wayneguard xp
Wayne-Dalton Corp.
One Door Drive
P.O. Box 67
Mt. Hope, Ohio 44660
Phone: 800-827-3667
330-674-7015
Fax: 330-763-8014
www.wayne-dalton.com
email: customerservice@wayne-dalton.com
OWNER’S MANUAL
MODEL
WAYNEGUARD XP
EXTENDED PERFORMANCE RELEASE DEVICE
TABLE OF CONTENTS
INTRODUCTION
WARNING
General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Agency Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Mechanical
CAUTION
WARNING
WARNING
Electrical
WARNING
CAUTION
WARNING
INSTALLATION
Important Installation Warnings . . . . . . . . . . . . . . . . . . . . . . . . . .4
Mount the Release Device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
CAUTION
WIRING
Wiring Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
Connections of Initiating Devices and Accessories . . . . . . . . . .7-8
Optional Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9
When you see these Safety Symbols and Signal Words on the
following pages, they will alert you to the possibility of serious
injury or death if you do not comply with the warnings that
accompany them. The hazard may come from something
mechanical or from electric shock. Read the warnings carefully.
When you see this Signal Word on the following pages, it will
alert you to the possibility of damage to your door and/or the
door operator if you do not comply with the cautionary
statements that accompany it. Read them carefully.
TESTING
Test Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
TROUBLESHOOTING
Operational Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
MAINTENANCE
Maintenance Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Enclosure Mounted LEDs Status Indicators . . . . . . . . . . . . . . . .12
IMPORTANT NOTES:
• BEFORE attempting to install, operate or maintain the release
device, you must read and fully understand this manual and
follow all safety instructions.
• DO NOT attempt repair or service of your release device unless
you are an Authorized Service Technician.
ACCESSORIES AND REPLACEMENT PARTS . . . . . . . .13
APPENDIX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
OPERATOR NOTES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
INTRODUCTION
GENERAL DESCRIPTION
The release device must be powered from 24Vdc received from
an approved UL 1481 regulated power supply with battery
backup. The devices can be activated via a smoke detector or an
alarm relay from the panel’s Form C dry contact relay. The release
device features include a 10-, 20-, 30- or 60-second delay on
alarm, closed door detection capabilities, Form C relay outputs for
the transmission of alarm and trouble signals transmitted to the
fire alarm control panel, an audible trouble sounder, and
diagnostic feedback LEDs.
The WayneGuard XP Release Device is UL/ULC listed normally
energized fail-safe device designed for use on rolling doors,
single-slide and center-parting level and inclined track doors. All
models are normally energized fail-safe releasing devices
incorporating state-of-the-art electronic control circuitry. The
release devices respond to emergency conditions generated from
an automatic initiating device and are used in conjunction with a
temperature fuse link system.
This device is designated to be used with manual doors, but can
be used on motorized doors incorporating a fusible link assembly
and drop-out mechanism.
2
INTRODUCTION
AGENCY REQUIREMENTS
WARNING
Installation and testing to factory specifications shall be
performed by factory authorized personnel for proper operation in
accordance with the latest National Fire Protection Association
(NFPA), Underwriters Laboratories (UL), National Electrical Code
(NEC), local, state, county, district and/or other applicable
building and fire standards, guidelines, regulations and codes
including, but not limited to, all appendices and amendments and
the requirements of the local authority having jurisdiction (AHJ).
To prevent possible SERIOUS INJURY or DEATH:
• DO NOT use this device without fuse links installed.
• Test every 90 days to assure proper operation of release
device.
CAUTION
SPECIFICATIONS
ELECTRICAL SPECIFICATIONS
VOLTAGE RATING:
STANDBY CURRENT:
ALARM CURRENT:
INITIATING DEVICE:
24Vdc
.100A
.15A
Maximum line impedance 20 ohm;
Maximum current not to exceed
.010A.; Maximum voltage 28Vdc
COMMON ALARM AND
TROUBLE RELAY:
(MAX. CONTACT RATING)
.5A 125Vac, 60Hz
1A 24Vdc Resistive
MECHANICAL SPECIFICATIONS
LOAD RATING:
PHYSICAL DIMENSIONS:
WEIGHT:
Support and Release 40 lbs. Max.
9.7" x 7.5" x 5" (h x w x d)
Approximately 8 lbs.
PREPARATION
It is imperative that the wall or mounting surface provide
adequate support for the release device.
Refer to the door manufacturer’s recommendations for use of this
product with specific door being utilized. Use only hardware
approved or recognized by the appropriate testing and listing
agencies in conjunction with the installation of this product.
Additional items may be required to complete the installation:
• Concrete anchors or fasteners
• Sash chain or 1/16 cable
• Eyebolts-hook
• Fuse links
• Turnbuckles
• Smoke detectors (up to 4 may be installed with this device)
Refer to NFPA 72 and NFPA 80 for instructions concerning proper
placement and detection coverage. End-of-line devices shall be
installed for supervision of electrical power to 4-wire smoke
detector. When using 4-wire smoke detectors with this device,
electrical supervision must be provided by means of a UL/ULC
listed end-of-line relay.
Eyebolt
Fuse Links
Turnbuckle
Smoke Detector
Releasing
Unit
Chain End
Link
Chain
Fire Door
3
WARNING
I N S TA L L AT I O N
IMPORTANT INSTALLATION INSTRUCTIONS
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
1. READ AND FOLLOW ALL INSTALLATION WARNINGS
AND INSTRUCTIONS.
2. NEVER connect release device to power source until
instructed to do so.
3. DO NOT install this device on a motorized door without
an electric safety edge.
4. DO NOT use this device without fuse links installed.
5. Concrete anchors MUST be used if mounting release
device into masonry.
6. DO NOT exceed maximum pull rating of 40 lbs. on
releasing device.
Mechanical
Reset Plunger
Classification:
Releasing device as defined by Underwriters Laboratories.
Installation Requirements:
Intended for “Indoor Dry” locations; all wiring must be performed
in accordance with the most current version of NFPA 72 - National
Fire Alarm Code and the National Electric Code.
End Link
MOUNT THE RELEASE DEVICE
Installation procedures vary according to door types. Refer to
door manufacturer’s recommendation that applies to your door.
1. Mount the release device on a vertical surface with chain end
link exiting side of enclosure.
2. Secure the release device enclosure with fasteners (#10 is the
minimum size recommended). If installing in masonry, use
concrete anchors (not provided).
3. Install hardware (sash chain or 1/16 cable, eyebolts-hook, fuse
links, turnbuckles—not provided) according to door
manufacturer’s recommendations. NOTE: The end link direction
of pull must be perpendicular to the side of the release device
enclosure. Install an eyebolt a minimum distance of 12" from
the release device to adequately redirect sash chain pull.
4. Install end link by pressing mechanical reset to allow insertion
of end link. Push end link completely in and release mechanical
reset to latch end link.
5. Remove sash chain or cable slack by adjusting turnbuckle.
Eyebolt
Fuse Links
Turnbuckle
Smoke Detector
Releasing
Unit
Chain End
Link
Chain
Fire Door
4
NING
WARNING
W
IRING
ION
WARNING
To reduce the risk of SEVERE INJURY or DEATH:
• ALL electrical connections MUST be made by a qualified
individual.
• Disconnect power at the fuse box BEFORE proceeding. Release
device MUST be properly grounded and connected in
accordance with local electrical codes.
• ALL power wiring should be on a dedicated circuit and well
protected. The location of the power disconnect should be
visible and clearly labeled.
• ALL power and control wiring MUST be run in separate
conduit.
• Installation of ALL wiring and connections, including Class 1
and Class 2 circuits, shall be performed in accordance with,
but not limited to, the latest NFPA, UL and N.E.C. standards
and codes. In addition, ALL installations subject to Canadian
standards shall be performed in accordance with the Canadian
Electrical Code, Part I, with respect to wiring material type,
wiring gauge related to power capacity requirements and
circuit length and wiring methods.
WARNING
WIRING INSTRUCTIONS
CAUTION
Verify wiring configuration with that recommended by door
manufacturer for use of this product with specific door and
accessories being utilized. 18-gauge wire is recommended.
1. Turn off power supply sources for the release device as well as
the door operator, if applicable, before beginning.
2. Verify voltage rating of release device to power source being
utilized. Voltage is indicated on the side of the unit. Verify that
power is disconnected before proceeding.
3. Connect 24Vdc power to terminal board positions 1 and 2
(Figure 2). Observe proper polarity. 24Vdc power input from an
approved UL 1481 regulated power supply with battery backup.
To prevent DAMAGE to the circuit board, ALL connections from
terminals 3 through 16 MUST be dry contact type.
FIGURE 1
Mechanical Reset
Plunger
Option
DIP Switch
FIGURE 2
1
2
5
+
–
24Vdc from an Approved UL 1481
Regulated Power Supply
with Battery Backup
WIRING
WIRING DIAGRAM
+ In
+ Out
- In/Out
2-Wire Detector
Initiation Loop (1) (3)
Keep 10k Ohm resister
between 5 & 6 if unused.
+ In
+ Out
- In/Out
Field Wiring shall consist of 22-18 AWG wiring.
1. Supervised, power limited circuit, 20 Ohm maximum line impedance.
2. Unsupervised, power limited circuit, 20 Ohm maximum line impedance.
3. Maximum of 4 Class B Style A detectors.
4. Power from an approved UL1481 regulated supply with battery backup.
Resistor
10k Ohm EOL
NC
COM
Normally Closed
Initiation Loop (1) (3)
Keep jumper between
3 & 4 if unused.
External power required.
014G0962B
+ 24Vdc
Input Power
(4)
PTC1
U3
LED7
GND_FAULT
K2
D1
SW1
1 2 3 4
C1
2
3
4
5
16 15 14 13 12 11 10 9 8
CL_LIMIT
LED2
C4
7
6
U4
NC_FAULT
LED4 LED5 LED6
R6
U2
2W_FAULT
1
P2
C2
2W_OP
Common Relay
Connections
Alarm NC
Alarm Com
Alarm NO
Trouble NC
Trouble Com
Trouble NO
K3
+
(YE)
P1
(GY)
K1
Solenoid
SW2
SW3
POWER ON
LED 1
DISABLE
LED 3
N.O. Close
Door Proximity
Switch (2)
6
WIRING
CONNECTIONS OF INITIATING DEVICES AND
ACCESSORIES
WARNING
A maximum of 4 smoke detectors may be installed with this
device. Refer to NFPA 72 and NFPA 80 for instructions
concerning proper placement and detection coverage. End-of-line
devices must be installed for supervision of electrical power to
4-wire smoke detector. When using 4-wire smoke detectors with
this device, electrical supervision must be provided by means of a
UL/ULC listed end-of-line relay.
NOTE: For low voltage wiring #18 AWG is recommended.
Normally Open “2-Wire,” Class B Style A Initiating Devices
Connect wiring from N/O initiating device loop to positions 3 and
4. Place the supervisory resistor (10k ohm @ 1/2 watt) contained
within the accessory pack. (Figure 3). Observe proper polarity, 3
(+), 4 (–) when attaching to the release device’s terminal board.
NOTE: Make certain that the factory-installed jumper between
terminal positions 5 and 6 remains in place. This option is a
supervised, current-limited circuit.
OR
Normally Open “4-Wire,” Class B Style A Initiating Devices
Connect wiring from N/O 4-Wire initiating device loop to
positions 3 and 4, making sure an end-of-line supervisory
resistor (10k ohm @ 1/2 watt) is installed as shown in Figure 4
or 5, depending upon the type of smoke detector being used.
Observe proper polarity, 3 (+), 4 (–) when attaching to the release
device’s terminal board. NOTE: Make certain that the factoryinstalled jumper between terminal positions 5 and 6 remains in
place. This option is a supervised, current-limited circuit.
OR
Normally Closed “4-Wire,” Class B Style A Initiating Devices
After removing the factory-installed jumper between terminal
positions 5 and 6, connect wiring from N/C 4-Wire initiating
device loop to positions 5 and 6 (Figure 6). This option is a
supervised, current-limited circuit. NOTE: Make certain that the
factory-installed resistor between positions 3 and 4 remains in
place.
NOTE: End-of-line devices must be installed adjacent and after
the last initiating device. Initiating device loops are supervised
and cannot be direct series or paralleled between multiple release
devices or shared with other alarm equipment. For proper wiring
configurations from multiple smoke detectors or signaling for
simultaneous closure on multiple doors, call technical support,
1-800-827-3667. Incorrect wiring between devices may cause
damage to the release control circuit and void warranty.
OR
Relay Module Installation as described on the following page.
To prevent possible SERIOUS INJURY or DEATH:
• End-of-line devices MUST be installed for supervision of
electrical power to 4-wire smoke detector.
• DO NOT install this device on a motorized door without an
electric safety edge.
CAUTION
10k Ohm @1/2 watt
Supervisory Resistor
(LMEOLRES-10)
FIGURE 3
– IN/OUT
+ OUT
+ IN
– IN/OUT
+ OUT
+ IN
24Vdc Power
from Terminal
Strip
3
NOTE: Follow this method of
attachment when using LM2W-B,
LM2WT-B, or other 2-wire 24Vdc
smoke detectors.
4
FIGURE 4
(–)
NOTE: Follow this method of attachment when using
LM4W-B, LM4WT-B, or other N/O 4-wire smoke detectors.
Power from
Control Panel
(+)
LMEOLR1224
12/24 Vdc
EOL Relay
Terminal Strip
4
FIGURE 5
(+)
COM
NO
– IN/OUT
+ OUT
+ IN
COM
NO
– IN/OUT
+ OUT
+ IN
3
10k Ohm @ 1/2 watt
Supervisory Resistor
(LMEOLRES-10)
NOTE: Follow this method of attachment when using
LM1424, LM1412, or other N/O 4-wire smoke detectors.
Power from
Control Panel
(–)
(+)
LMEOLR1224
12/24 Vdc
EOL Relay
(+)
Alarm
Contacts
Style A
(N/O)
(–)
(–)
10k Ohm @ 1/2 watt
Supervisory Resistor
(LMEOLRES-10)
Terminal Strip
3
4
(+)
(–)
FIGURE 6
IMPORTANT: When using 4-wire smoke detectors with this device,
the smoke detectors must be powered from a source other than the
release device, such as an approved UL 1481 regulated power supply
providing battery backup support.
(–)
Power from
Control Panel
NOTE: Generic version of a N/C
4-wire smoke detector is shown.
(+)
(+)
(+)
(–)
(–)
N/C
Terminal Strip
C
N/C
LMEOLR1224
12/24 Vdc
EOL Relay
C
Purple
5
6
7
IMPORTANT: When using 4-wire smoke detectors with this
device, the smoke detectors must be powered from a source
other than the release device, such as an approved UL 1481
regulated power supply providing battery backup support.
WARNING
WIRING
CONNECTIONS OF INITIATING DEVICES AND
ACCESSORIES (cont’d)
CAUTION
To prevent DAMAGE to the circuit board, ALL connections from
terminals 3 through 16 MUST be dry contact type.
Relay Module Installation
In lieu of smoke detectors, the release device may be put into
alarm by the fire alarm control panel. Most commonly, a relay
module is used as an interface between the fire alarm control
panel and the release device. The relay module must provide
Form C dry contacts for connection to the appropriate terminals
on the release device (Figure 7).
NOTE: When choosing a relay module to activate the release
device in an alarm condition, always select one that provides
Form C dry contact relays. Do not use any relay module
providing or passing any (control) voltage through the contacts
into the release device. The passage of voltage through such a
relay module into the release device will cause problems with the
operation of the device and may damage the device’s terminals
and/or circuit board.
FIGURE 7
Relay Module
5
Common
6
Normally Closed
Red
–
Black
Fire Alarm
Control Panel
+
Terminal Strip
FIGURE 8
7
Attach to Common on
N/O Proximity Switch
8
Attach to N/O Position
on Proximity Switch
OPTIONAL CONNECTIONS
CLOSE DOOR DETECTION OPTION
Connect wiring from N/O electrical loop, using a proximity switch
or other similar device with dry contacts, to 7 and 8 (Figure 8).
The switch should be placed to engage when the door is in the
closed position and so that it will toggle states from its N/O
condition (switch closed when door is closed) to a closed
condition indicating that the door edge has made contact with
desired down position. When the switch is closed by contact
from the door, the release device will not activate on alarm,
thereby eliminating nuisance gravity drops through the
inadvertent release of the fusible link assembly. This option only
works as long as power is available to unit. Fail-safe operation is
maintained under all operating conditions, and if power is not
available to the unit, the fusible link assembly will be released.
This is a power-limited, unsupervised circuit. The proximity
switch and the release device MUST be mounted in the same
room.
RELAY AND TROUBLE OUTPUTS OPTION
Connect wiring from the Alarm Relay Outputs (#11 N/C or #13
N/O and #14 Common) to the appropriate inputs on the fire alarm
control panel to provide a signal at the panel when the release
device is in an alarm state. Connect wiring from the Trouble Relay
Outputs (#14 N/C or #16 N/O and #15 Common) to the
appropriate inputs on the fire alarm control panel to provide a
signal at the panel that the release device is in a trouble state
(Figure 9). If these features are desired, coordinate the
interconnection between the Release Device and the Fire Alarm
Control Panel with the fire alarm installer.
Proximity Switch
Part No. LM56A
FIGURE 9
8
11
N/C Alarm Relay Output
12
Common
13
N/O Alarm Relay Output
14
N/C Trouble Output
15
Trouble Common
16
N/O Trouble Output
Make all necessary
connections to the
Fire Alarm Panel as
required by the project
specifications and
the Authority Having
Jurisdiction
WIRING
FIGURE 10
OPTIONAL CONNECTIONS (cont’d)
DIP SWITCH SELECTION
The release device will provide a factory default delay of 10
seconds (to minimize nuisance alarms) before releasing the
fusible link chain upon alarm or power loss. A 4-position DIP
Switch found on the PC board within the release device can be
used to adjust the length of the delay to one of four preset delays.
The optional delay settings are as follows:
NOTE: Position 4 is unused and should remain in the OFF position.
Position 3 is used to select one of the two available voice messages.
ON
1
Delay Setting
2
3
4
Switch Position
Factory default setting of 10 seconds shown.
1
2
3
4
10 Seconds
Off
Off
Off
Off
20 Seconds
Off
On
Off
Off
30 Seconds
On
Off
Off
Off
60 Seconds
On
On
Off
Off
NOTE: Set all DIP switch options before applying power to the
system.
9
TESTING
TEST PROCEDURES
WARNING
TO BE PERFORMED BY FACTORY AUTHORIZED PERSONNEL
ONLY! CLEAR FIRE DOOR OPENING AND PROHIBIT TRAFFIC
THROUGH DOOR OPENING WHILE TESTING!
Testing does not affect normal operation of alarm system when
connected to release device/control panel. Testing of the release
device is independent of, and shall in no way be interpreted as an
alternative method of, testing of a central fire alarm system,
motorized operator and/or any other system component employed
on the fire door or counter fire door installation. Complete testing
and normal operation can only be accomplished with power
applied to unit. Door must be in open position with power applied
to unit to begin testing. The following procedures describe testing
of all options. Verify options ordered and installed with unit. All
tests may not apply. Refer to Figure 1 for location of all the LEDs
and switches mentioned in this section.
INITIAL POWER UP
1. Apply line power to the release device.
2. Power LED (red) will be lit on the bottom of the release
device.
To prevent possible SERIOUS INJURY or DEATH:
• Clear fire door opening and prohibit ALL traffic through door
opening while testing.
• Test every 90 days to assure proper operation of release
device.
CAUTION
FIGURE 1
Mechanical
Reset Plunger
MECHANICAL RELEASE
1. Depress and continue to hold test button on side of release
device. After the selected delay expires, the device will release
the end link and allow door to drop. Release test button.
2. Reset the door per door manufacturer’s instructions. Raise
door and then reset the release device by pushing downward on
the mechanical reset button at the top of the device. Fully
insert the end link through the side opening on the device and
release the reset button in order to latch end link.
Front of Release Device
Bottom of Release Device
Test Button
CLOSE DOOR DETECTION (OPTIONAL)
1. Using the chain hoist or motor operator, lower the door to
fully closed position.
2. Verify that Close Door Detection LED (yellow) is lit indicating
door closure. Depress and continue to hold test button on
side of release device for 10 seconds. Close Door Detection
logic will prohibit the release device from energizing and
releasing the end link. Reset the test button.
3. Raise door to fully open position.
SUSPENSION OF POWER
1. Make sure door is in fully open position. Turn off all power to
release device. Immediately upon loss of power to the release
device, a mechanical release will be initiated.
2. Reset the door per door manufacturer’s instructions. Raise
the door and then reset the release device by pushing
downward on the mechanical reset button at the top of the
device. Fully insert the end link through the side opening on
the device and release the reset button in order to latch end
link. Press the “Reset” button on the side of the device to
reset the alarm loop.
After completing all tests, make sure the door is in its normal
condition (open or closed) and all power required for normal
operation is restored to unit. The release device is designed to
operate with power applied.
NOTE: Testing shall be performed and witnessed for proper
operation.
Electronic
Reset Button
Red LED (Line Power Present)
Yellow LED
(Close Door Detection
Release Disabled)
10
End Link
TROUBLESHOOTING
CHECK THE CLOSE DOOR DETECTION
Is the Yellow LED on the bottom of the enclosure lit? If lit, the
close limit is active and the device is disabled and will not release
the tension on the door spring as the door is in the closed
position, activating the proximity switch. If not lit, check wiring
instructions in Figure 8.
OPERATIONAL CHECKLIST
POWER
Is the red LED, labeled “Power,” located on the bottom of the
enclosure lit?
Is the Red LED Lit?
Yes
Move on.
No
Check power connections at terminal board positions 1 and 2.
Check voltage; voltage should be 24Vdc received from an
approved UL 1481 regulated power supply.
CHECK THE ALARM
Are the alarm (smoke detection) inputs correct? If not, the
release device will not release the fusible link assembly in a fire
condition. Conversely, the release device will always release the
fusible link assembly when powered or reset.
Are the Alarm Inputs correct?
Yes
Move on.
No
Check that it is a dry contact input. There should not be any
voltage on the alarm lines when they are disconnected from the
unit.
Check to see if it is tied into an addressable relay module of an
alarm panel. At times, noise can be picked up from these
modules.
CIRCUIT BOARD DIAGNOSTIC LEDS
View diagnostic LEDs present on the circuit board located behind
the terminal board. Refer to the table below for the status LED
indications.
LED
LED Color
Description
N/O Detector
Trouble
Yellow
(LED 4)
If lit, indicates a trouble condition (a short) within the N/O 2-wire (or 4-wire) smoke detector loop
(emanating from terminal board positions 3 and 4), resulting from either incorrect wiring or
incorrect placement of the end-of-line resistor, and the smoke detector loop is inactive. Refer to the
Smoke Detector Installation section on pages 7 and 8 of this manual for correct wiring instructions.
N/O Detector
Alarm
Red
(LED 5)
If lit, indicates that the N/O 2-wire (or 4-wire) smoke detector loop (emanating from terminal board
positions 3 and 4) is in alarm. When lit during testing, press the Auxiliary Reset Button at the
bottom of the release device to reset the loop.
N/C Detector
Trouble
Red
(LED 6)
If lit, indicates an open circuit within the N/C 4-wire smoke detector loop (emanating from terminal
board positions 5 and 6), resulting from either incorrect wiring or incorrect placement of the endof-line relay or the detector(s) are in alarm. If in alarm, cycle power off and then on to the smoke
detectors to reset, then depress the auxiliary reset button to reset. Refer to the Smoke Detector
Installation section on pages 7 and 8 of this manual for correct wiring instructions.
Close Door
Detection
Green
(LED 2)
If lit, indicates that the fire door or shutter is closed and activating the proximity switch. If not lit,
refer to the Close Door Detection section of this manual for correct wiring instructions.
Ground Fault
Yellow
(LED 7)
If lit, indicates that one of the ancillary devices/loops (smoke detector, annunciator, etc.) is not
grounded properly, and a short to earth ground exists.
11
WARNING
WARNING
MAINTENANCE
MAINTENANCE REQUIREMENTS
CAUTION
WARNING
The release device has no scheduled maintenance requirements.
The unit has been designed and tested for use in dry, indoor
locations. Testing of the unit at least once every 90 days is
recommended, but test intervals shall ultimately be subject to
criteria established by the Authority Having Jurisdiction (AHJ).
To avoid SERIOUS PERSONAL INJURY or DEATH from
electrocution, disconnect ALL power BEFORE performing
ANY maintenance.
FIGURE 1
Mechanical
Reset Plunger
Front of Release Device
Bottom of Release Device
End Link
Electronic
Reset Button
Test Button
Red LED (Line Power Present)
Yellow LED
(Close Door Detection
Release Disabled)
ENCLOSURE MOUNTED LEDS STATUS INDICATORS
LED Label LED Color
Description
Action Required
Disable
Yellow
The Yellow LED will light when the door reaches the close
limit and activates a proximity switch attached to terminal
positions 7 and 8 on the release device. This
configuration results in the device not releasing the
fusible link assembly in alarm or power loss situations
and should only be used when the fire door is kept in a
constant closed position.
If the LED does not light when the door reaches the close
limit and activates the proximity switch, then check that
the proximity switch has been activated and that the
switch is set to normally open (N.O.). Check to make
certain that the switch is attached to terminal positions 7
and 8 on the release device.
Power
Red
If the Red LED is lit, then the line power is connected and
switched “on.”
If the LED does not light when power is applied, check
that power is connected as described in the installation
manual electrical connections.
12
ACCESSORIES AND REPLACEMENT PARTS
ACCESSORIES
ITEM
1
2
PART #
LM8100
LM8100T
3
4
LM8100I
LM2W-B
5
LM2WT-B
6
LM4W-B
DESCRIPTION
Smoke Detector - 120V Photo
Smoke Detector - 120V Photo with
Thermal
Smoke Detector - 120V Ion
Smoke Detector - 12/24Vdc 2-Wire
Photo
Smoke Detector - 12/24Vdc 2-Wire
Photo with Thermal
Smoke Detector - 12/24Vdc 4-Wire
Photo
ITEM
7
8
9
10
11
12
13
PART #
LM4WT-B
DESCRIPTION
Smoke Detector - 12/24Vdc 4-Wire
Photo with Thermal and Form C Relay
LM1424
Smoke Detector - 24Vdc Ion
LM1412
Smoke Detector - 12Vdc Ion
LMTH135
Heat Detector - 135 Degree Fixed
Temperature
LMTH194
Heat Detector - 194 Degree Fixed
Temperature
LMEOLR1224 End-of-Line Relay - 12/24Vdc
LMEOLR120 End-of-Line Relay - 120Vac
REPLACEMENT PARTS
ITEM
1
2
3
4
PART #
LMRK
LMELH
01-32046
LMEOLRES-10
DESCRIPTION
Reset Knob
End Link
Owner's Manual
End-of-Line Resistor, 10 kOhm
NOTE: Certain accessories above will require a separate power source. Refer to product manual.
HOW TO ORDER REPAIR PARTS
OUR LARGE SERVICE ORGANIZATION SPANS AMERICA
Installation and service information call:
(800) 827-3667
13
APPENDIX
ACCESSORY COMPATIBILITY GUIDE
SMOKE DETECTORS
MODEL NO.
DESCRIPTION
SYSTEM SENSOR
MODEL NO.
LM2W-B
24Vdc 2-Wire Photo
2W-B
LM2WT-B
24Vdc 2-Wire Photo with Thermal
2WT-B
LM4W-B
24Vdc 4-Wire Photo
4W-B
LM4WT-B
24Vdc 4-Wire Photo with Thermal & Form C Relay
4WT-B
24Vdc Ion
#1424
LM1424
HEAT DETECTORS
MODEL NO.
DESCRIPTION
SYSTEM SENSOR
MODEL NO.
CHEMTRONICS
MODEL NO.
EDWARDS SYSTEM TECHNOLOGY
(EST) MODEL NO.
LMTH135
135 Degree Fixed Temperature
#5603
#603
#283B-PL
LMTH194
194 Degree Fixed Temperature
#5604
#604
#284B-PL
END-OF-LINE DEVICE
MODEL NO.
DESCRIPTION
SYSTEM SENSOR
MODEL NO.
SPACE AGE
ELECTRONICS NO.
LMEOLRES-10 10 kOhm End-of-Line Resistor
LMEOLRES-10
LMEOLR1224 End-of-Line Relay
LMEOLR120
LIFTMASTER NO.
EOLR-1
End-of-Line Relay
PAM-1
NOTE: Certain accessories above will require a separate power source. Refer to product manual.
14
O P E R AT O R N O T E S
15
01-32050B
Issue Date 9/13/2006
© 2006, The Chamberlain Group, Inc.
All Rights Reserved
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising