Manuel d`utilisation 3M MP8795

Manuel d`utilisation 3M MP8795
Document téléchargé sur www.lampe-videoprojecteur.info
MP8795
Multimedia Projector
Operator's Guide
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
Liquid Crystal Projector
ENGLISH
Operator's Guide
Thank you for purchasing this liquid crystal projector.
WARNING • Please read the “Product Safety Guide” and this “Operator's
Guide” thoroughly to ensure correct usage through understanding. After
reading, store this instruction manual in a safe place for future reference.
NOTE • The information in this manual is subject to change without notice.
• The manufacturer assumes no responsibility for any errors that may appear in this manual
• The reproduction, transmission or use of this document or contents is not permitted without
express written authority.
TRADEMARK ACKNOWLEDGMENT : PS/2, VGA and XGA are registered trademarks of
International Business Machines Corporation. Apple, Mac and ADB are registered trademarks of
Apple Computer, Inc. VESA and SVGA are trademarks of the Video Electronics Standard
Association. Windows is a registered trademark of Microsoft Corporation. Carefully observe the
trademarks and registered trademarks of all companies, even when not mentioned.
CONTENTS
Page
Page
FEATURES .......................................2
BEFORE USE ...................................2
TROUBLESHOOTING ....................20
Contents of Package ..............................2
Part Names.............................................3
Loading the Batteries..............................5
INSTALLATION ................................6
Installation of the Projector and Screen........6
Angle Adjustment ...................................6
Cabling ...................................................7
Power Connection ..................................8
Example of System Setup ......................8
Plug & Play .............................................8
OPERATIONS ...................................9
Power ON ..................................................9
Power OFF ..............................................9
Basic Operation ....................................10
Setup Menu ..........................................12
Input Menu............................................13
Image Menu..........................................14
Options Menu .......................................15
No Signal Menu ....................................16
MAINTENANCE ..............................17
Lamp.....................................................17
Air Filters ..............................................19
Other Maintenance ...............................19
OSD Message ......................................20
Indicators Message ..............................21
Symptom ..............................................22
SPECIFICATIONS...........................23
ACCESSORIES...............................24
.......................................................................................
TABLES
Table 1. Installation Reference.................6
Table 2. Cabling .......................................7
Table 3. Basic Operation ........................10
Table 4. Setup Menu ..............................12
Table 5. Input Menu................................13
Table 6. Image Menu..............................14
Table 7. Options Menu ...........................15
Table 8. No Signal Menu ........................16
Table 9. OSD Message ..........................20
Table 10. Indicators Message ................21
Table 11. Symptom ................................22
Table 12. Specifications .........................23
.......................................................................................
For "TECHNICAL" , see the end of this
manual.
© 3M 2003. All Rights Reserved.
ENGLISH-1
3M™ Multimedia Projector MP8795
FEATURES
This liquid crystal projector is used to project various computer signals as well as NTSC / PAL /
SECAM video signals onto a screen. Little space is required for installation and large images can
easily be realized.
Outstanding Brightness
The UHB lamp and high-efficiency optical system assure a high level of brightness.
Partial Magnification Function
Interesting parts of images can be magnified for closer viewing.
Distortion Correction Function
Distortion-free images are quickly available.
BEFORE USE
Contents of package
Make sure all of the following items are included in the package. If anything is missing, please
contact your dealer.
NOTE • Keep the original packing material for future reshipment.
R
ECTO
ABLE
PORT
PROJ
MP
8795
MP8
795
Power Cord x3
(US, UK, Europe)
S-Video
Cable
Stereo Mini-Cable
Projector
MP8795
Multimedia Projector
Product Safety Guide
VGA Cable
MP8775i Projecteur multimedia - Guide de Securite de Produit
MP8775i Multimedia-Projektor - Sicherheitsanleitung des Gerats
MP8775i Proyector de Multimedia - Guía de Seguridad del Producto
MP8775i Proiettore Multimediale - Guida di Sicurezza del Prodotto
MP8775i Multimedia Projector - Veiligheidgids op Product
MP8775i Projector dos Multimedia - Guia da Seguranca de Produto
MP8775i Multimedia Projektør- Bruksanvisning for Produktsakerhets
Video/Audio
Cable
(with white lead)
PROJECTOR
PORTABLE
MP8775
MP8775
Component Video
Cable
(with green lead)
BLANK
STANDBY/ON
LASER
Product Safety Guide
Warranty
Quick Start Guide
VIDEO
RGB
AUTO
Mouse cable x3
(PS/2, ADB, Serial)
Batteries
for Remote Control
Transmitter
MENU
KEYSTONE
MENU SELECT
RESET
POSITION
FREEZE
MAGNIFY
PinP
MUTE
OFF
FOCUS
ZOOM
VOLUME
Remote Control
Transmitter
ENGLISH-2
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
BEFORE USE (continued)
ENGLISH
Part Names
FOCUS Button
ZOOM Button
–
KEYSTONE Button
ZOOM
+
–
FOCUS
KEYSTONE
+
INPUT Button
INPUT
MENU
STANDBY/ON Button
STANDBY ON
LAMP
TEMP
MENU Button
RESET
RESET Button
LAMP Indicator
TEMP Indicator
POWER Indicator
Control Panel
(Refer to P.9 "OPERATIONS")
Remote Control Sensor
Control Panel
ECTO
PORT
ABLE
Lens
R
PROJ
MP87
95
Filter Cover
( Air Filter )
Ventilation Openings
(exhaust)
Carrying Handle
MP87
95
Foot Adjuster
Filter cover
Air Filter and Intake
for the Cooling Fan
(
Lens Cap
Front/Right View
Remote Control Sensor
PO
RTAB
LE
)
Foot Adjuster
MP
8795
OJEC
PR
TO
R
Terminal Panel
(Refer below)
Speaker
Power Switch
AC Inlet
(to Power Cord)
Rear/Left View
DVI Terminal
RGB IN 1 Terminal
RGB IN 2 Terminal
DVI
S-VIDEO Terminal
1
VIDEO Terminal
S-VIDEO
AUDIO(MONO)/L
Terminal
COMPO
NENT
VIDEO
RGB IN
2
CONTROL Terminal
CONTROL
RGB OUT
VIDEO
(MONO)/L
Y
AUDIO
AUDIO R Terminal
USB
R
CB/PB
RGB OUT Terminal
AUDIO IN
RGB 1 RGB 2
DVI
AUDIO
OUT
AUDIO IN RGB1/DVI Terminal
AUDIO IN RGB2 Terminal
AUDIO OUT Terminal
CR/PR
USB Terminal
Terminal
Panel
© 3M 2003. All Rights Reserved.
COMPONENT VIDEO
Y Terminal
CB/PB Terminal
CR/PR Terminal
ENGLISH-3
3M™ Multimedia Projector MP8795
BEFORE USE (continued)
Part Names (continued)
STANDBY/ON Button
VIDEO Button
N
BLA
/ON
DBY
STAN
LAS
BLANK Button
LASER Button
K
ER
RGB Button
B
RG
Disk Pad
MOUSE / RIGHT Button
IDEO
V
Used to operate the
mouse shift function and
left click function.
Used to click the right
mouse button.
KEYSTONE Button
AUTO Button
MENU Button
O
AUT
MENU SELECT Button
Used to click the left
mouse button.
,
,
,
ME
RESET Button
Used to click the right
mouse button.
TONE
KEYS
NU
ME
NU
ION
POSIT
SEL
ECT
ET
RES
FREEZE Button
TE
MU
Button
Used to operate the
mouse shift function.
PinP Button
PinP
EZE
FRE
NIFY
MAG
OFF
MUTE Button
E
US
FOC
POSITION Button
M
ZOO
M
VOLU
VOLUME Button
ZOOM Button
MAGNIFY Button
FOCUS Button
REMOTE CONTROL TRANSMITTER
(Refer to P.9 "OPERATIONS")
These functions work when the mouse control function is activated. Remember, the POSITION,
BLANK ON and MENU ON functions disable the mouse control function.
WARNING • The laser pointer of the remote control transmitter is used in place of a
finger or rod. Never look directly into the laser beam outlet or point the laser beam at
other people. The laser beam can cause vision problems.
CAUTION • Use of controls or adjustments or performance of procedures other than
those specified herein may result in hazardous radiation exposure.
AVOID EXPOSURELASER RADIATIONS IS
EMITTED FROM THIS
APERTURE
C A U T I O N
LASER RADIATIONDO NOT STARE INTO BEAM
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
CLASS2 LASER PRODUCT
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS2 LASER PRODUCT
MAX. OUTPUT: 1mW
WAVE LENGTH: 650nm
IEC60825-1 : 1993+A1:1997
Complies with 21 CFR 1040. 10 and 1040. 11 except for deviations
pursuant to Laser Notice No.50, dated 2001.7.26
SMK CORPORATION
6-5-5 Togoshi Shinagawa-ku, Tokyo, JAPAN 142-8511
MANUFACTURED Novemver 2001
PLACE OF MANUFACTURER: A
NOTE • Keep the remote control transmitter away from children and pets.
• Do not give the remote control transmitter any physical impact. Take care not to drop.
• Do not place the heavy objects on the remote control transmitter.
• Do not wet the remote control transmitter or place it on any wet object.
• Do not place the remote control transmitter close to the cooling fan of the projector.
• Do not disassemble the remote control transmitter.
ENGLISH-4
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
BEFORE USE (continued)
Install the AA batteries into the remote control
transmitter.
1. Remove the battery cover.
Push the knob while lifting up the battery cover.
2. Load the batteries.
Make sure the plus and minus poles are correctly
oriented.
3. Close the battery cover.
ENGLISH
Loading the Batteries
1
2
CAUTION • Use only the specified batteries with this remote control
transmitter. Also, do not mix new and old batteries. This could cause
battery cracking or leakage, which could result in fire or personal injury.
• When loading the batteries, make sure the plus and minus terminals are
correctly oriented as indicated in the remote control transmitter. Incorrect
orientation could cause battery cracking or leakage, which could result in
personal injury or pollution of the surrounding environment.
• When you dispose the battery, you should obey the law in the relative area or
country.
• Keep the battery away from children and pets.
• When not to be used for an extended period, remove the batteries from the
remote control transmitter.
NOTE Replace the batteries when remote control transmitter operation becomes difficult.
© 3M 2003. All Rights Reserved.
ENGLISH-5
3M™ Multimedia Projector MP8795
INSTALLATION
Installation of the Projector and Screen
Refer to the drawing and table below for determining the screen size and projection distance.
The projection distances shown in the table below
Screen
are for full size (1024 x 768 dots).
a: Distance from the projector to the screen. (±10%)
b: Distance from the lens center to the bottom of the
screen. (±10%)
Table 1. Installation Reference
Screen size
[inches (m)]
a [inches (m)]
Min.
Max.
b
[inches (cm)]
40 (1.0)
60 (1.5)
55 (1.4)
85 (2.2)
73 (1.9)
114 (2.9)
1
2
(3)
(4)
80 (2.0)
114 (2.9)
151 (3.8)
2
(6)
100 (2.5)
144 (3.7)
191 (4.9)
3
(7)
120 (3.0)
176 (4.5)
231 (5.9)
3
(9)
150 (3.8)
220 (5.6)
282 (7.2)
4 (11)
200 (5.0)
291 (7.4)
386 (9.8)
6 (15)
Top View
Lens center
b
a
Side View
CAUTION • Install the projector in a suitable environment according to instructions of
the “Product Safety Guide” and this manual.
• When you fix this unit with a metal tool and the like, you must connect it with ground
wire; otherwise, fire or electric shock can result.
Connect the ground terminal of AC inlet of this unit with the ground terminal provided at the
building using an optional three-core power-supply cord.
• Please basically use liquid crystal projector at the horizontal position. If you use liquid
crystal projector by the lens up position, the lens down position and the side up position, this
may cause the heat inside to build up and cause damage. Be especially careful
not to install it with ventilation holes blocked.
• Do not install LCD projector in smoke effected environment. Smoke residue may buildup
on critical parts (i.e.LCD panel, Lens Assy etc.).
Angle Adjustment
Use the foot adjusters on the bottom of the
projector to adjust the projection angle. It is
variable within 0˚ to 9˚ approximately.
1. Lift up the front side of the projector, and
pressing the foot adjuster button, adjust the
projection angle.
2. Release the button to lock at the desired angle.
3. Use the foot adjusters for fine adjustment.
Do not force the adjuster screws.
This could damage the adjusters or cause the
lock to fail.
Foot Adjusters
Variable within the range of approximately 0° - 9°
CAUTION • Do not release the foot adjuster button unless the projector is
being held; otherwise, the projector could overturn or fingers could get
caught and cause personal injury.
ENGLISH-6
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
INSTALLATION (continued)
ENGLISH
Cabling
Refer to the table below for connecting each terminal of the projector to a device.
Table 2. Cabling
Function
Analog RGB input
Terminal
RGB IN 1
RGB IN 2
Analog RGB output
RGB OUT
Digital RGB input
DVI
Audio input
(from the computer)
Cable
VGA cable with D-sub 15-pin jack
and inch thread screws
DVI cable with inch thread screws
AUDIO IN [RGB 1] / [DVI]
(interlocked with RGB IN 1 or DVI)
Audio cable with stereo mini jack
AUDIO IN [RGB 2]
(interlocked with RGB IN 2)
PS/2 mouse control
PS/2 mouse cable
ADB mouse control
ADB mouse cable
CONTROL
Serial mouse control
Serial mouse cable
RS-232C communication
RS-232C cable
USB mouse control
USB
USB cable
S-video input
S-VIDEO
S-video cable with mini DIN 4-pin jack
Video input
VIDEO
Video/audio cable
COMPONENT VIDEO Y
Component video input
COMPONENT VIDEO CB/PB
Component video cable
COMPONENT VIDEO CR/PR
Audio input
(from video equipment)
AUDIO (MONO)/L
AUDIO R
Video/Audio cable
or Audio cable with RCA jack
Audio output
AUDIO OUT
Audio cable with stereo mini jack
CAUTION • Incorrect connecting could result in fire or electrical shock.
Please read this manual and the “Product Safety Guide”.
• Before connecting, turn off to all devices to be connected, except for the USB
cable.
• The cables may have to be used with the core set to the projector side. Use the
cables which are included with the projector or specified.
NOTE • Before connecting, read instruction manuals of the devices to be connected, and make sure that the
projector is compatible with the device.
• Secure the screws on the connectors and tighten.
• For some RGB input modes, the optional Mac adapter is necessary.
• To select the DVI input, the computer may need some settings. See the manuals of the computer for details.
• Some computers may have multiple display screen modes. Use of some of these modes will not be possible
with this projector.
• Refer to the “TECHNICAL” section for the pin assignment of connectors and RS-232C communication data.
• When the DVI terminal is used, the RGB OUT terminal may not function.
© 3M 2003. All Rights Reserved.
ENGLISH-7
3M™ Multimedia Projector MP8795
INSTALLATION (continued)
Power Connection
Use the correct power cord depending on the power outlet to be used.
Connect the AC inlet of the projector to the power outlet firmly by the power cord.
CAUTION • Be carful in handling the power
cord according to instructions of the "Product
Safety Guide" and this manual.
• Connect the power cord firmly. Avoid using a
loose, unsound outlet or failed contact.
Power outlet
PORT
ABLE
MP
879
5
PROJ
ECTO
R
AC Inlet
Power Cord
Example of System Setup
Computer
(desktop type)
Computer
(notebook type)
S-Video Tape
Recorder
DIGTAL
RGB IN
S-VIDEO
COMPO
NENT
VIDEO
2
Display
Monitor
CONTROL
RGB OUT
VIDEO
(MONO)/L
AUDIO
USB
R
CB/PB
AUDIO IN
RGB 1 RGB 2
DIGITAL
AUDIO
OUT
CR/PR
Speaker
with
amplifier
DVD Player
Computer (desktop type)
NOTE • When connecting with a notebook computer, set the proper RGB external image output
(setting CRT display or simultaneous display of LCD and CRT). Please read instruction manual of
the notebook for more information.
Plug & Play
This projector is VESA DDC 1/2B compatible. Plug & play is possible by connecting to a computer
that is VESA DDC (Display Data Channel) compatible.
Please use this function by connecting the VGA cable with RGB IN 1 terminal (DDC 1/2B
compatible), or by connecting a DVI cable with DVI terminal (DDC 2B compatible).
Plug & play may not operate by other connections.
NOTE • Plug & play is a system configured with peripheral equipment including a computer,
display and an operating system.
• This projector is recognized as a plug & play monitor. Use the standard display drivers.
• Plug & play may not operate by the computer to connect. Use the RGB IN 2 terminal if plug &
play does not operate correctly.
ENGLISH-8
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
POWER Indicator
STANDBY/
ON Button
STANDBY/ON Button
LASER
VIDEO
RGB
ZOOM button
LE
RTAB
PO
5
879 R
MPPROJECTO
FOCUS button
BLANK
STANDBY/ON
Y ON
STANDB
MUTE
–
ZOOM
LAM
P PWE
U
– FOCU
S
R TEMP
RESET
MEN
+
INPUT
+
AUTO
MENU
8795
MP
KEYSTONE
MENU SELECT
RESET
POSITION
Power Switch
FREEZE
MAGNIFY
PinP
MUTE
OFF
FOCUS button
FOCUS
Power ON
Lens cap
ZOOM
VOLUME
ZOOM button
1. Check that the power cord is connected correctly.
2. Set the power switch to [ | ]. The standby mode is selected, and the POWER indicator is turned to
orange.
3. Press the STANDBY/ON button
on the control panel or the remote control transmitter.
Warm-up begins and the POWER indicator blinks in green.
4. The POWER indicator ceases blinking and turns to green when power is on. Remove the lens
cap.
5. Adjust picture size using the ZOOM button.
6. Adjust focus using the FOCUS button .
Power OFF
1. Press the STANDBY/ON button
on the control panel or the remote control transmitter. Then,
the message "Power off?" will appear on the screen, and the message will disappear by any
operation or no operation for 5 seconds. During this message indication, press the
STANDBY/ON
button again. The projector lamp is extinguished and lamp cooling begins.
The POWER indicator blinks orange during lamp cooling. Pressing the STANDBY/ON button
has no effect while the POWER indicator is blinking.
2. The system assumes the Standby mode when cooling is complete, and the POWER indicator
ceases blinking and changes to orange. Check that the indicator is orange and set the Power
switch to [O].
3. The POWER indicator is extinguished when power is off. Attach the lens cap.
WARNING • Please read this manual, and the “Product Safety Guide”
thoroughly before using the equipment. Always ensure that the equipment is
used safely.
NOTE • Except in emergencies, follow the above-mentioned procedure for turning power off.
Incorrect procedure will reduce the life of the projector lamp and LCD panel.
• To prevent any trouble, turn on/off the projector when the computer or video tape recorder is OFF.
Providing a RS-232C cable is connected, turn on the computer before the projector.
• When a projector continues projecting the same image, the image may remain as an afterimage.
Please do not project the image same for a long time.
© 3M 2003. All Rights Reserved.
ENGLISH-9
ENGLISH
OPERATIONS
3M™ Multimedia Projector MP8795
OPERATIONS (continued)
Basic Operation
The basic operations shown in Table 3 is performed from the supplied remote control transmitter or
the projector control panel. Items indicated by (*) may be used from the control panel.
Table 3 . Basic Operation
Item
Description
Select Input Signal (*) : Press the INPUT button.
RGB IN 1 → RGB IN 2 → DVI
→ VIDEO → S-VIDEO → COMPONENT VIDEO (→ RGB IN 1)
Select RGB Input : Press the RGB button.
INPUT
SELECT
VIDEO/S-VIDEO/COMPONENT VIDEO → RGB IN 1/RGB IN 2/DVI
RGB IN 1 → RGB IN 2 → DVI (→ RGB IN 1)
Select Video Input : Press the VIDEO button.
RGB IN 1/RGB IN 2/DVI → VIDEO/S-VIDEO/COMPONENT VIDEO
VIDEO → S-VIDEO → COMPONENT VIDEO (→ VIDEO)
• The selected signal name is displayed for approximately 3 seconds when the input
signal is changed.
Set/Clear Position Adjustment Mode : Press the POSITION button.
The [
] icon is displayed in the POSITION mode.
POSITION
Image Position Adjustment: Press the
POSITION mode.
,
,
and
buttons in the
RESET (*)
Initialize Each Item : Select an item and press the RESET button.
Initialize Position Adjustment : Press the RESET button and the
POSITION mode. This function is valid only when RGB signal is input.
• Valid only in the MAGNIFY mode with a video signal is input.
• After approximately 10 seconds of inactivity the [ ] icon is extinguished and the
POSITION mode is cleared automatically.
•
, ,
and
buttons may operate as the mouse control button. Refer to page 4.
• Valid except for the VOLUME, LANGUAGE, WHISPER and H PHASE.
• The RESET button may operate as the mouse control button. Refer to page 4.
MAGNIFY
Set MAGNIFY Mode : Press the MAGNIFY
button.
Move Magnified Area : Run the POSITION in the MAGNIFY mode.
Adjust Magnification : Press the MAGNIFY
/
button in MAGNIFY
mode.
Clear MAGNIFY Mode : Press the MAGNIFY
button.
OFF
• The MAGNIFY mode is cleared by running or setting the AUTO, ASPECT, INPUT
SELECT or VIDEO, or by changing the input signal.
Set/Clear FREEZE Mode : Press the FREEZE button. The [II] icon is
displayed, and the image is frozen, in the FREEZE mode.
FREEZE
• The FREEZE mode is cleared by running or setting POSITION, VOLUME, MUTE,
Automatic Adjustment, BLANK ON/OFF, or MENU ON/OFF, or by changing the input
signal.
• Do not forget to clear frozen static images.
NOTE • Use the remote control transmitter at a distance of approximately 5m from the sensor on
the front of the projector, and within a range of 30° left-right. Strong light and obstacles will
interfere with operation of the remote control transmitter.
ENGLISH-10
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
OPERATIONS (continued)
ENGLISH
Items indicated by (*) may be used from the control panel.
Table 3. Basic Operation (continued)
Item
Description
VOLUME
Volume Adjustment : Press the VOLUME
MUTE
Set/Clear Mute Mode : Press the MUTE button. No sound is heard in the
MUTE mode.
AUTO
button.
/
Automatic Adjustment at RGB Input : Press the AUTO button. Horizontal
position(H.POSIT), vertical position (V.POSIT),clock phase (H.PHASE), and
horizontal size(H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input : Press the AUTO button. A signal
type appropriate for the input signal is selected automatically. Valid only
when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals.
BLANK
ON/OFF
Set/Clear Blank Mode: Press the BLANK button. No image is displayed in
the Blank mode. The screen color is as set in BLANK on the Image menu.
Menu Display Start/Stop: Press the MENU button.
MENU
• The menu display is terminated automatically after approximately 10 seconds of
ON/OFF (*)
inactivity.
Select Menu Type: Press the MENU SELECT button. Allows the user to
select the normal menu or the single menu. Only the selected item is
displayed on the single menu, and other items are displayed with the
and
buttons as with the normal menu.
MENU
SELECT
• Valid only when the Setup menu is used. Push the MENU SELECT button after
selecting items such as "BRIGHTNESS".
• The MENU SELECT button may operate as the mouse control button. Refer to
page 4.
Normal menu
Single menu
(MENU SELECT)
SETUP
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
OPT.
0
-2
100
100
+1
800
0
0
CONTRAST
P.IN P.
MODE
Select Mode of P.IN P. Display : Press the PinP button.
Small → Large → P.IN P. off ( → Small)
ZOOM (*)
Adjust Screen Size : Press the ZOOM
/
FOCUS (*)
Adjust Focus : Press the FOCUS
button.
-2
• P.IN P. function superimposes a video image over RGB or DVI signals.
/
button.
Set / Clear KEYSTONE Mode : Press the KEYSTONE
button.
Select
KEYSTONE
Mode
:
Press
the
/
button
in
the
KEYSTONE
KEYSTONE
(*) mode.
↔
Horizontal
Vertical
Adjust KEYSTONE : Press the
/
button.
© 3M 2003. All Rights Reserved.
ENGLISH-11
3M™ Multimedia Projector MP8795
OPERATIONS (continued)
Setup Menu
SETUP
The following adjustments and settings are possible
when SETUP is selected at the top of the menu. Part
of the Setup menu differs between RGB input and
video input. Select an item with the
and
buttons, and start operation. Use the Single menu to
reduce menu size (see Table 3, MENU SELECT).
Table 4. Setup Menu
Item
INPUT
BRIGHT
CONTRAST
V POSIT
H POSIT
H PHASE
H SIZE
COLOR BAL R
COLOR BAL B
ASPECT
IMAGE
SETUP
OPT.
0
-2
INPUT
IMAGE
OPT.
0
+1
+1
0
0
+1
0
0
BRIGHT
CONTRAST
SHARPNESS
COLOR
TINT
H PHASE
COLOR BAL R
COLOR BAL B
ASPECT
100
100
+1
800
0
0
VIDEO
S-VIDEO
COMPONENT VIDEO
RGB IN 1
RGB IN 2
DVI
Description
↔ Light
RGB IN 1
RGB IN 2
DVI
VIDEO
S-VIDEO
COMPONENT
✔
✔
✔
BRIGHT
Adjustment: Dark
CONTRAST
Adjustment: Weak
↔ Strong
✔
✔
✔
V POSIT
Adjustment: Down
↔ Up
✔
-
-
H POSIT
Adjustment: Left
↔ Right
✔
-
-
H PHASE
Adjustment: Left
↔ Right
• Adjust to eliminate flicker.
✔
-
✔
H SIZE
↔ Large
• The image may not be displayed correctly if the horizontal
size is excessive. In such cases, press the RESET button,
and initialize the horizontal size.
✔
-
-
SHARPNESS
Adjustment: Soft
↔ Clear
-
-
✔
COLOR
Adjustment: Light
↔ Dark
-
-
✔
-
-
✔
Adjustment: Small
TINT
↔ Green
• Valid only when NTSC or NTSC 4.43 signal is received.
Adjustment: Red
COLOR BAL R Adjustment: Light
↔ Dark
✔
✔
✔
COLOR BAL B Adjustment: Light
↔ Dark
✔
✔
✔
✔
✔
-
-
-
✔
Select Image Aspect Ratio :
4:3[
]
↔
16:9[
]
Select Position of Image:
Press the
button while 16:9[
] is selected.
Center →
Down →
Up ( → Center
)
ASPECT
Select Image Aspect Ratio:
4:3[
]
↔
16:9[
]
↔
4:3 small[
Select Position of Image :
Press the
button while 16:9[
] / 4:3 small[
is selected.
Center →
Down →
Up ( → Center
)
]
]
• 4:3 small cannot be selected with the input of 720P or
1080i component.
• 4:3 small may not be displayed correctly with some input
signals.
ENGLISH-12
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
Input Menu
The following functions are available when INPUT is selected on the
menu. Select an item with the
and
buttons, and start or stop
operation with the
and
buttons. The function indicated (**) are
effective on video input mode only, not on RGB input mode, except in
the P.IN P. window on RGB input mode.
Table 5. Input Menu
Item
AUTO
RGB
SETUP
INPUT
AUTO
RGB
VIDEO
VIDEO NR
Progressive
BLACK
HDTV
IMAGE
OPT.
EXECUTE
CANCEL
Description
Automatic Adjustment at RGB Input: Select the EXECUTE with the
button.
Horizontal position (H.POSIT), vertical position (V.POSIT), clock phase (H.PHASE),
and horizontal size (H.SIZE) are automatically adjusted. Use with the window at
maximum size in the application display.
Automatic Adjustment at Video Input: Select the EXECUTE with the
button. A
signal type appropriate for the input signal is selected automatically when EXECUTE
is selected automatically. Valid only when AUTO is set for VIDEO on the menu.
• This operation requires approximately 10 seconds. It may not function correctly with
some input signals. Pressing the AUTO button in this case may correct this problem.
• This function is the same as for the AUTO function in Basic operation.
Displays RGB Input Frequency: Displays the horizontal and vertical sync signal
frequencies for RGB input.
• Valid only at RGB input.
VIDEO (**)
Select Video Signal Type: Select the signal type with the
and
buttons.
Select NTSC, PAL, SECAM, NTSC4.43, M-PAL, or N-PAL as appropriate for the
input signal. The selection of AUTO enables and executes the function AUTO
(Automatic Adjustment at Video Input), except for the N-PAL input.
• Use this function when the image becomes unstable (eg. the image becomes
irregular, or lacks color) at VIDEO/S-VIDEO input.
• Automatic Adjustment requires approximately 10 seconds. It may not function
correctly with some input signals. Pressing the AUTO button in this case may correct
this problem except for the N-PAL input.
• For the COMPONENT VIDEO input, this function is not effective and the signal type
is distinguished automatically. Refer to the item HDTV of the OPT. Menu for the
signal of HDTV.
VIDEO NR
(**)
Set/Clear Noise Reduction Mode: Select the TURN ON / TURN OFF with the
/
button. When the TURN ON is selected, the NR mode is active and the noise on
screen of the video input will be reduced.
• Valid except for the HDTV.
Progressive
(**)
BLACK(**)
HDTV (**)
Select Progressive Mode: Select the mode suitable for the input signal with the
and
buttons. The TV mode and the FILM mode convert the interlaced video signal
into the progressive signal. The FILM mode is adptable 2-3 Pull-Down system to the
conversion.
• Use this function to raise resolution, at the interlaced video input except HDTV
signal.
Set/Clear Black Enhancement Mode: Select the TURN ON / TURN OFF with the
/
button. When the TURN ON is selected, the black enhancement mode is
active and the contrast ratio of the screen for the video input will be raised by making
black level darker.
Select HDTV mode: Select the 1035i mode or 1080i mode suitable for the input
signal with the
/
button.
© 3M 2003. All Rights Reserved.
ENGLISH-13
ENGLISH
OPERATIONS (continued)
3M™ Multimedia Projector MP8795
OPERATIONS (continued)
Image Menu
SETUP
The following adjustments and settings are available when IMAGE is
selected on the menu. Select an item with the
and
buttons, and
start or stop operation with the
and
buttons.
Table 6. Image Menu
Item
INPUT
BLANK
START UP
MyScreen
MIRROR
P.IN P. POSIT
P.IN P. INPUT
GAMMA
IMAGE
OPT.
MyScreen
ORIGINAL
Description
BLANK
Select Blank Screen: Select the screen in case of the BLANK mode with the
/
button.The selected one (MyScreen, ORIGIAL or one colors) is displayed when the
BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGIAL is selected, the screen is going to the black after
several minutes.
START UP
Select Start Up Screen:Select the screen in case of no signal input with the
/
button. The selected one (MyScreen, ORIGIAL or TURN OFF) is displayed when no
signal is input
MyScreen is a mode that the customer-customized screen is displayed. This is the
blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGIAL is selected, the screen is going to the black after
several minutes.
MyScreen
Set MyScreen Mode: Select the EXECUTE with the
button to display the
MyScreen menu and set the MyScreen mode for BLANK and START UP functions.
ESC clears and closes the menu box.
NORM. is default of the MyScreen menu.
FREEZE freezes the image and displays the frame to capture.
Press the
button after freeze to go to the MyScreen Capture Position mode.
In the MyScreen Capture Position mode, the buttons
,
,
and
allow to
move the frame to capture.
After adjusting the position, press the KEYSTONE button to go to the MyScreen
Display Size mode.
To cancel freezing and return to the NORM. of the MyScreen menu, press the
RESET button.
In the MyScreen Display Size mode, select the magnification x1, x2 or FULL with the
button
/
.
After selecting the magnification, press the KEYSTONE button to go to the CAPT.
mode and start capturing.
To return to the MyScreen Capture Position mode, press the RESET button.
CAPT. executes a capturing the image. It requires about 20 seconds. After capturing,
the captured image will be displayed for about 10 seconds.
MIRROR
Select Mirror Status: Select mirror status with
P. IN P.
POSIT
Select Position of P. in P. Display : Press the
/
button.
↔
↔
↔
• P.IN P. function superimposes a video image over RGB or DVI signals.
P. IN P.
INPUT
Select signal of P. in P. Display : Press the
/
VIDEO
↔
S-VIDEO
↔
COMPONENT
GAMMA
Select Gamma Mode: Select the gamma mode with the
NORMAL
↔
CINEMA
↔
DYNAMIC
ENGLISH-14
/
© 3M 2003. All Rights Reserved.
button.
button.
/
button.
3M™ Multimedia Projector MP8795
Options Menu
SETUP
The following adjustments and settings are available when OPT. is
selected on the menu. Select an item with the
and
buttons, and
start operation.
INPUT
IMAGE
OPT.
16
VOLUME
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
Table 7. Options Menu
Item
Description
↔ Increase VOLUME
VOLUME
Volume Adjustment: Reduce VOLUME
MENU COLOR
Select Menu Background Color: Select with the
and
buttons.
LANGUAGE
Operation Start/Stop: Press the
/
button.
Select Menu Display Language: Select with the
and
buttons.
AUTO OFF
Operation Start/Stop: Press the
/
button.
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The
system automatically enters the standby mode when a signal is not
received for the set time.
Clear AUTO OFF: Select STOP (0 min.) with the
button. When
STOP is selected the system does not enter the standby mode even if
no signal is received.
SYNC ON G
WHISPER
Operation Start/Stop: Press the
/
button.
SYNC ON G Valid: Select TURN ON with the
button.
SYNC ON G Invalid: Select TURN OFF with the
button.
• May not be displayed correctly with some input signals when SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set SYNC ON G to invalid, and reconnect the signal.
Set / Crear WHISPER Mode: Press the
/
button. When the
WHISPER is selected, the WHISPER mode is active. In the WHISPER
mode, acoustic noise level from the unit is reduced, and brightness level
on screen is a little lower.
© 3M 2003. All Rights Reserved.
ENGLISH-15
ENGLISH
OPERATIONS (continued)
3M™ Multimedia Projector MP8795
OPERATIONS (continued)
No Signal Menu
The same adjustments and settings are available with the Image and
Options menus when the MENU button is pressed during display of the
“NO INPUT IS DETECTED ON ***” or “SYNC IS OUT OF RANGE
ON ***” message while no signal is received.
VOLUME
BLANK
START UP
MIRROR
MENU COLOR
LANGUAGE
AUTO OFF
SYNC ON G
WHISPER
16
Table 8. No Signal Menu
Item
Description
VOLUME
Volume Adjustment: Reduce VOLUME
↔ Increase VOLUME
• When this function is used, audio input is automatically switched to video. The
audio input can be switched by moving the DISK PAD left and right during the
display of the volume adjustment bar. The volume adjustment bar is displayed by
pressing VOLUME
or VOLUME
button.
BLANK
Select Blank Screen: Select the screen in case of the BLANK mode with the
/
button.The selected one (MyScreen, ORIGIAL or one colors) is displayed
when the BLANK mode is ON.
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
• When MyScreen or ORIGIAL is selected, the screen is going to the black after
several minutes.
START UP
Select Start Up Screen:Select the screen in case of no signal input with the
/
button. The selected one (MyScreen, ORIGIAL or TURN OFF) is displayed
when no signal is input
MyScreen is a mode that the customer-customized screen is displayed. This is
the blue screen at the factory setting. Refer to the description of MyScreen below.
ORIGINAL is a mode that the factory fixed screen is displayed.
TURN OFF displays the blue screen.
• When MyScreen or ORIGIAL is selected, the screen is going to the black after
several minutes.
MIRROR
Operation Start/Stop: Press the
/
button.
Select Mirror Status: Select the mirror status with the
MENU COLOR
Select Menu Background Color: Select the color with the
LANGUAGE
Operation Start/Stop: Press the
/
button.
Select Menu Display Language: Select the language with the
AUTO OFF
Operation start/stop: Press the
/
button.
Set AUTO OFF: Set 1~99 minutes with the
and
buttons. The system
automatically enters the standby mode when a signal is not received for the set
time.
Clear AUTO OFF: Select the STOP (0 min.) with the
button. When the STOP
is selected the system does not enter the standby mode even if no signal is
received.
SYNC ON G
Operation Start/Stop: Press the
/
button.
SYNC ON G Valid: Select the TURN ON with the
button.
SYNC ON G Invalid: Select the TURN OFF with the
button.
• May not be displayed correctly with some input signals when the SYNC ON G is
valid. In such cases, remove the signal connector so that no signal is received,
set the SYNC ON G to invalid, and reconnect the signal.
WHISPER
Set / Crear WHISPER Mode: Press the
/
button. When the WHISPER is
selected, the WHISPER mode is active. In the WHISPER mode, acoustic noise
level from the unit is reduced, and brightness level on screen is a little lower.
ENGLISH-16
© 3M 2003. All Rights Reserved.
and
buttons.
and
buttons.
and
buttons.
3M™ Multimedia Projector MP8795
Lamp
HIGH VOLTAGE
HIGH TEMPERATURE
HIGH PRESSURE
Contact your dealer before replacing the lamp.
For the optional lamp, see the item “ACCESSORIES” of P.24.
Before replacing the lamp, switch power OFF, remove the power cord from the power outlet, and
wait approximately 45 minutes until the lamp has cooled. The lamp may explode if handled at high
temperatures.
WARNING • For disposal of used lamp, treat
according to the instruction of community
authorities.
• Since the lamp is made of glass, do not apply shock
to it and do not scratch it.
• Also, do not use old lamp. This could also cause
explosion of the lamp.
• Premature lamp failure MAY be caused by an
electronic component in the projector and not
necessarily the lamp. If unsure contact your local
service center.
• If it is probable that the lamp has exploded (explosive
sound is heard), disconnect the power plug from the
power outlet and ask your dealer to replace lamp. The
lamp is covered by front glass , but, in rare cases, the
reflector and the inside of the projector may be
damaged by scattered broken pieces of glass, and
broken pieces could cause injury when being handled.
• Do not use the projector with the lamp cover removed.
Lamp
Reflector
Front
glass
Lamp Life
Projector lamps have a finite life. The image will become darker, and hues will become weaker,
after a lamp has been used for a long period of time.
Replace the lamp if the LAMP indicator is red, or the CHANGE THE LAMP message appears
when the projector is switched ON. See Table 9 of P.20 and Table 10 of P.21.
NOTE • The LAMP indicator is also red when the lamp unit reaches high temperature. Before
replacing the lamp, switch power OFF, wait approximately 20 minutes, and switch power ON again.
If the LAMP indicator is still red, replace the lamp.
© 3M 2003. All Rights Reserved.
ENGLISH-17
ENGLISH
MAINTENANCE
3M™ Multimedia Projector MP8795
MAINTENANCE (continued)
Replacing the Lamp
1. Switch the projector OFF, remove the power cord from the
power outlet, and wait at least 45 minutes for the unit to cool.
2. Prepare a new lamp.
3. Check that the projector has cooled sufficiently, and gently
turn it upside down.
4. Loosen the screw as shown in the diagram, and remove the
lamp cover.
5. Loosen the two screws, and gently remove the lamp while
holding the grips. Touching the inside of the lamp case may
result in uneven coloring.
6. Install the new lamp and tighten the two screws firmly. Also
steadily push the opposite side of the screwed lamp into the
unit.
7. Replace the lamp cover in position and tighten the screw
firmly.
8. Gently turn the projector right-side up.
CAUTION • Ensure that screws are tightened
properly. Screws not tightened fully may result
in injury or accidents.
• Do not use the projector with the lamp cover
removed.
Resetting the Lamp Timer
Reset the lamp timer after replacing the lamp. When the lamp has been replaced after the LAMP
indicator is red, or the CHANGE THE LAMP message is displayed, complete the following
operation within ten minutes of switching power ON. The power will be turned off automatically in
over 10 minutes.
1. Switch power ON, and press the RESET button, for approximately three seconds. The ‘LAMP
xxxx hr’ message will appear on the lamp timer on the bottom of the screen.
2. Press the MENU button on the remote control transmitter, or the RESET button on the control
panel, while the lamp timer is displayed. The ‘LAMP xxxx → 0 ■ CANCEL’ message will
then appear.
3. Press the
and select 0, and wait until the timer display is cleared.
NOTE • Do not reset the lamp timer without replacing the lamp. Reset the lamp timer always
when replacing the lamp. The message functions will not operate properly if the lamp timer is not
reset correctly.
ENGLISH-18
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
Air Filters
TAB
POR
LE
Cleaning Air Filters
filter cover
795TOR
JEC
MP8
PRO
BY ON
STAND
MUTE
–
ZOOM
LAMP
PWER
TEMP
T
RESE
MENU
+
– FOCUS
INPU
+
T
This projector uses 2 air filters. These air filters should be
cleaned as described below at intervals of approximately
100 hours.
1. Switch the projector power supply OFF, and remove the
power cord from the power outlet.
2. Remove the filter cover and the air filter.
3. Clean the air filter with a vacuum cleaner.
4. Set the air filter and the filter cover.
795
MP8
filters
Replacing the Air Filter
Replace the air filter if contamination cannot be removed, or if it is damaged.
1. Switch the projector power supply OFF, and remove the power cord from the power outlet.
2. Remove the filter cover and the old filter.
3. Set the new filter and the filter cover.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the “Product Safety
Guide” thoroughly to ensure that maintenance is performed correctly.
• Replace the air filter if contamination cannot be removed, or if it is damaged.
Contact your dealer in such case. For the optional air filter, see the item
“ACCESSORIES” of P.24.
• Do not use the equipment with the air filter removed.
• When the air filter is clogged with dust etc. the power supply is switched OFF
automatically to prevent the temperature rising inside the projector.
Other Maintenance
Maintenance Inside the Equipment
For safety reasons, ensure that the equipment is cleaned and checked by the dealer once every two
years. Maintaining the equipment by yourself is dangerous.
Cleaning the Lens
Gently wipe the lens with lens cleaning paper. Do not touch the lens with your hands.
Cleaning the Cabinet and Remote control transmitter
Gently wipe with a soft cloth. If dirt and stains etc. are not easily removed, use a soft cloth
dampened with water, or water and a neutral detergent, and wipe dry with a soft, dry cloth.
CAUTION • Switch power OFF and remove the power cord from the power
outlet before beginning maintenance work. Please read the “Product Safety
Guide” thoroughly to ensure that maintenance is performed correctly.
• Do not use detergents or chemicals other than those noted above (e.g. benzene
or thinners).
• Do not use cleaning sprays.
• Do not rub with hard materials, or tap the equipment.
© 3M 2003. All Rights Reserved.
ENGLISH-19
ENGLISH
MAINTENANCE (continued)
3M™ Multimedia Projector MP8795
TROUBLESHOOTING
Service Infomation
For product infomation,product assistance,service infomation,or to order accessories,please call:
In U.S.or Canada :1-800-328-1371
In other locations,contact your local 3M sales office.
OSD Message
The messages as described below may appear on the screen at power ON. Take the appropriate
measures when such messages appears.
Table 9. OSD Message
Message
Contents
CHANGE THE LAMP
The usage time of lamp will be reaching 2000 hr shortly.(*2)
AFTER REPLACING LAMP,
It is recommended to replace the lamp soon. Prepare a new
RESET THE LAMP TIME.
lamp as a replacement.
(*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL TURN OFF
AFTER ** hr.
(*1)
CHANGE THE LAMP
AFTER REPLACING LAMP,
RESET THE LAMP TIME.
THE POWER WILL
TURN OFF
AFTER 0 hr.
The usage time of lamp will be reaching 2000 hr shortly. It is
recommended to replace the lamp within * * hours.(*2)
It might be happened that the lamp is cut off before * * hr by any
chance. Power will be switched OFF automatically in * * hours.
Replace the lamp as shown in P.17~18 “Lamp”. Always reset
the lamp timer after replacing the lamp.
The usage time of lamp is about to reach. Power will be
switched OFF in a few minutes.(*2)
Switch power OFF immediately and replace the lamp as shown
in P.17 ~18 “Lamp”. Always reset the lamp timer after replacing
the lamp.
NO INPUT IS DETECTED
ON ***
No input signal found.
Check signal input connections and signal sources.
SYNC IS OUT OF RANGE
ON ***
The horizontal or vertical frequency of the input signal is not
within the specified range.
Check the specifications of the equipment and the signal source.
CHECK THE AIR FLOW
The internal temperature has risen.
Switch power OFF, and wait 20 minutes until the equipment
cools.
Check the following and Switch power ON again.
* Are the ventilation openings blocked.
* Is the air filter dirty.
* Is the ambient temperature in excess of 35°C.
NOTE (*1) This message is cleared automatically after approximately three minutes, and
appears every time power is switched ON.
(*2) The unit has a function to turn the power off which will be active when the usage time reaches
2000 hr. However the life of lamp might be much different among lamps, so that it might be
happened that a lamp is cut off before the function is active.
ENGLISH-20
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
Indicators Message
The POWER indicator, LAMP indicator, and TEMP indicator are lit and blank as follows. Take the
appropriate measures.
Table 10. Indicators Message
POWER
LAMP
TEMP
indicator indicator indicator
Contents
Lights
orange
Turns off Turns off The Standby mode has been set.
Blinks
green
Turns off Turns off Warming up. Please wait.
Lights
green
Turns off Turns off ON. Normal operation possible.
Blinks
orange
Turns off Turns off Cooling. Please wait.
Lights red
Lights red
Lights
red
Lamp is not lit.
The interior of the equipment may be too hot. Switch
power OFF, wait 20 minutes until the equipment cools,
Turns off and check whether the ventilation openings are blocked,
whether the air filter is dirty, or whether the ambient
temperature exceeds 35 °C. And switch power ON
again. Replace the lamp if the same problem occurs.
Blinks
red
Lamp or lamp cover is not found, or hasn’t been fitted in
correctly.
Switch power OFF, and wait for 45 minutes until the
Turns off
equipment cools. Check fitting of the lamp and lamp
cover, and switch power ON again. Contact your dealer if
the same problem occurs again.
Lights red Turns off
Lights red Turns off
Blinks
red
The cooling fan is not operating.
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check for foreign matters in the fan,
and switch power ON again. Contact your dealer if the
same problem occurs again.
Lights
red
The interior of the equipment is too hot.
Switch power OFF, and wait for 20 minutes until the
equipment cools. Check whether the ventilation openings
are blocked, whether the air filter is dirty, or whether the
ambient temperature exceeds 35 °C. Then switch power
ON again. Contact your dealer if the same problem
occurs again.
NOTE When the internal temperature becomes excessive power is switched OFF automatically
for safety reasons, and the indicator is extinguished. Set the power switch to [O] and wait for 20
minutes until the equipment has cooled sufficiently.
© 3M 2003. All Rights Reserved.
ENGLISH-21
ENGLISH
TROUBLESHOOTING (continued)
3M™ Multimedia Projector MP8795
TROUBLESHOOTING (continued)
Symptom
Before requesting repair, check in accordance with the following chart. If the situation cannot be
corrected, then contact your dealer.
Table 11. Symptom
Symptom
The power is not
turned on.
Possible cause
Remedy
The main power switch is not
turned on.
Turn on the main power switch.
The power cord is
disconnected.
Plug the power cord into an AC
power outlet.
The input is not correctly set.
Use the projector or remote control
transmitter to set.
10
No signal input.
Connect correctly.
7,8
The projector is not correctly
connected.
Connect correctly.
7,8
No video or audio.
Video is present but
The volume is set to minimum.
no audio.
Press VOLUME
on the remote
control or display the menu screen
and adjust the volume.
Mute is turned on.
Press the MUTE
The projector is not correctly
connected.
Connect correctly.
button.
Audio is present but The brightness adjustment knob Select BRIGHT with the MENU
button and the press the
button.
is rotated fully clockwise.
no video.
The lens cap is still attached.
Colors are pale and Color density and color
color matching is
matching are not correctly
poor.
adjusted.
Images are dark.
Video is blurred.
ENGLISH-22
Page
Remove the lens cap.
8,9
11,15
11
7,8
12
9
Adjust the video.
12
Brightness and contrast are not
Adjust the video.
correctly adjusted.
12
The lamp is nearing the end of
its service life.
Replace with a new lamp.
17
WHISPER mode is set.
Clear WHISPER mode.
15
Focus or H PHASE is out of
adjustment.
Adjust the focus or H PHASE.
© 3M 2003. All Rights Reserved.
9,12
3M™ Multimedia Projector MP8795
ENGLISH
SPECIFICATIONS
Table 12. Specifications
Item
Specification
Product name
Liquid
crystal
panel
Liquid crystal projector
Panel size
3.3 cm (1.3 type)
Drive system
TFT active matrix
Pixels
786,432 pixels (1024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7 ~ 2.3 f=49.0 ~ 64.0 mm
Lamp
275 W UHB
Speaker
1.2 W + 1.2W (Stereo)
Power supply
AC100 ~ 120V, 4.7A / AC220 ~ 240V, 2.0A
Power consumption
440W
Temperature range
0 ~ 35°C (Operating)
Size
289 (W) x 144 (H) x 350 (D) mm
Weight (mass)
6.5 kg
1
RGB IN
RGB
signal
input
2
Video
signal
input
TMDS, DC: 150~1200 mV / AC: 1.56 Vp-p
TTL Level (Positive/Negative)
DVI
AUDIO IN
Video: Analog 0.7Vp-p, 75Ω terminator (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
RGB1
DVI
RGB2
200mVrms, 50 kΩ (max. 3.0Vp-p)
Stereo mini jack
VIDEO
1.0Vp-p, 75Ω terminator
RCA jack
S-VIDEO
Brightness signal: 1.0Vp-p, 75Ω terminator
Color signal: 0.3Vp-p (burst signal), 75Ω terminator
Mini DIN 4-pin jack
Y
1.0 Vp-p, 75 Ω Terminator (Positive)
COMPONENT
CB/CR 0.7 Vp-p, 75 Ω Terminator (Positive)
VIDEO
PB/PR 0.7 Vp-p, 75 Ω Terminator (Positive)
AUDIO
Signal
output
Control
functions
L/MONO 200mVrms, 50 kΩ (max. 3.0Vp-p)
RCA jack
R
RGB OUT
Video: Analog 0.7Vp-p, 75Ω output impedance (positive)
H/V. sync.: TTL level (positive/negative)
Composite sync.: TTL level
D-sub 15-pin shrink jack
AUDIO OUT
200mVrms, output impedance 1 kΩ (max. 3.0Vp-p)
Stereo mini jack
CONTROL
D-sub 15-pin shrink plug
USB
USB jack (B type)
NOTE • This specifications are subject to change without notice.
© 3M 2003. All Rights Reserved.
ENGLISH-23
3M™ Multimedia Projector MP8795
ACCESSORIES
Acccessories..................................................................................Part Number
UHB Lamp, 275W ..........................................................................78-6969-9548-5
Air Filter ...........................................................................................78-8118-8967-0
Power Cord (US) .............................................................................78-8118-8102-4
Power Cord (UK) .............................................................................78-8118-8101-6
Power Cord (Europe) .....................................................................78-8118-8103-2
VGA Cable ......................................................................................78-8118-8708-8
RCA Component Cable ..................................................................78-8118-8843-3
RCA Video/Audio Cable ..................................................................78-8118-3234-0
S-Video Cable ................................................................................78-8118-3238-1
Stereo Mini-Cable ..........................................................................78-8118-8846-6
Mouse Cable (PS/2) ......................................................................78-8118-8105-7
Mouse Cable (ADB) ........................................................................78-8118-8106-5
Mouse Cable (Serial) ......................................................................78-8118-8107-3
Remote Control Transmitter ...........................................................78-8118-8966-2
Not Included with Basic Packet....................................................Part Number
Ceiling mount .................................................................................78-6969-8924-9
Adjustable Height Suspension .......................................................78-6969-8312-7
Shipping Case ...............................................................................78-6969-8925-6
Carry Case .....................................................................................78-6969-8926-4
Mouse Cable (USB) ........................................................................78-8118-8186-7
RS-232C Control Cable ..................................................................78-8118-3312-4
Mac Adapter ...................................................................................78-8118-3308-2
How to Order
Please order these parts through your dealer, or contact 3M Customer Service at the
following number :
In U.S. or Canada : 1-800-328-1371
In other locations,contact your local 3M sales office.
ENGLISH-24
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
TECHNICAL
350
395
Dimension Diagram
289
144
88
139
308.5
Unit : mm
30.5
Signal Connector Pin Assignment
1. D-sub 15-pin Shrink Connector (RGB IN 1/RGB IN 2/RGB OUT)
Pin No
1
2
3
4
5
6
7
8
Signal
Video input Red
Video input Green
Video input Blue
Ground
Ground Red
Ground Green
Ground Blue
Pin No
Signal
9
10
11
-
12
13
14
Ground
Pin No
15
RGB IN 1: SDA(DDC)
RGB IN 2: RGB OUT: H. sync./ Composite sync.
Vertical sync
Signal
RGB IN 1: SCL(DDC)
RGB IN 2: RGB OUT: -
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
2. Digital Receptacle Connector (DVI)
Pin No
1
2
3
4
5
6
7
8
9
10
Signal
T.M.D.S. Data 2 T.M.D.S. Data 2 +
T.M.D.S. Data 2 / 4 Shield
DDC Clock
DDC Data
Analog V. Sync.
T.M.D.S. Data 1 T.M.D.S. Data 1 +
Pin No
Signal
11
12
13
14
15
16
17
18
19
20
T.M.D.S. Data 1 / 3 Shield
+5V Power
Ground (+5V, Analog H/V Sync.)
Hot-Plug Sense
T.M.D.S. Data 0 T.M.D.S. Data 0 +
T.M.D.S. Data 0 / 5 Shield
-
Pin No
21
22
23
24
Signal
T.M.D.S. Clock Shield
T.M.D.S. Clock +
T.M.D.S. Clock -
1 2 3 4
5 6 7 8
9 10 11 12 13 14 15 16
17 18 19 20 21 22 23 24
3. Mini Din 4-pin Connector (S-VIDEO)
Signal
1
Color:0.286Vp-p (NTSC, burst signal),75Ω terminator
0.3Vp-p (PAL/SECAM, burst signal),75Ω terminator
2
Brightness:1.0Vp-p, 75Ω terminator
3
Ground
4
Ground
© 3M 2003. All Rights Reserved.
TECHNICAL
Pin No
TECHNICAL - 1
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Example of computer signal
Resolution
H×V
fH (kHz)
fV (Hz)
Rating
Signal mode
Display
mode
720 × 400
37.9
85.0
VESA
TEXT
Zoom in
640 × 480
31.5
59.9
VESA
640 × 480
35.0
66.7
640 × 480
37.9
72.8
640 × 480
37.5
75.0
640 × 480
43.3
800 × 600
800 × 600
VGA (60Hz)
Zoom in
Mac13"mode
Zoom in
VESA
VGA (72Hz)
Zoom in
VESA
VGA (75Hz)
Zoom in
85.0
VESA
VGA (85Hz)
Zoom in
35.2
56.3
VESA
SVGA (56Hz)
Zoom in
37.9
60.3
VESA
SVGA (60Hz)
Zoom in
800 × 600
48.1
72.2
VESA
SVGA (72Hz)
Zoom in
800 × 600
46.9
75.0
VESA
SVGA (75Hz)
Zoom in
800 × 600
53.7
85.1
VESA
SVGA (85Hz)
Zoom in
Mac16"mode
Zoom in
832 × 624
49.7
74.5
1024 × 768
48.4
60.0
VESA
XGA (60Hz)
1024 × 768
56.5
70.1
VESA
XGA (70Hz)
1024 × 768
60.0
75.0
VESA
XGA (75Hz)
1024 × 768
68.7
85.0
VESA
XGA (85Hz)
1152 × 864
67.5
75.0
VESA
SXGA (75Hz)
Zoom out
1280 × 960
60.0
60.0
VESA
SXGA (60Hz)
Zoom out
1280 × 1024
64.0
60.0
VESA
SXGA (60Hz)
Zoom out
1280 × 1024
80.0
75.0
VESA
SXGA (75Hz)
Zoom out
1600 × 1200
75.0
60.0
VESA
VXGA (60Hz)
Zoom out
NOTE • Some computers may have multiple display screen modes. Use of some of these modes
will not be possible with this projector.
• Be sure to check jack type, signal level, timing and resolution before connecting this projector to a
computer.
• Depending on the input signal, full-size display may not be possible in some cases. Refer to the
number of display pixels above.
• The image may not be displayed correctly when the input sync. signal is "Composite Sync." or
"Sync. on G".
• The image might be something wrong with computer by computer on the DVI mode. In this case, it
is recommended to reduce the resolution and / or reflesh rate.
TECHNICAL - 2
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Instial set signals
The following signals are used for the instial settings.
The signal timing of some computer models may be different. In such case, refer to adjust the
V.POSIT and H.POSIT of the menu.
Back porch b
Front porch d
Display interval c
Back porch b
Front porch d
Display interval c
DATA
DATA
HSYNC
VSYNC
Sync a
Computer /
Signal
Sync a
Horizontal signal timing (µs)
TEXT
a
2.0
b
3.0
c
20.3
d
1.0
Computer /
Signal
Vertical signal timimg (lines)
TEXT
a
3
b
42
c
400
d
1
VGA (60Hz)
3.8
1.9
25.4
0.6
VGA (60Hz)
2
33
480
10
Mac 13"mode
2.1
3.2
21.2
2.1
Mac 13"mode
3
39
480
3
VGA (72Hz)
1.3
3.8
20.3
1.0
VGA (72Hz)
3
28
480
9
VGA (75Hz)
2.0
3.8
20.3
0.5
VGA (75Hz)
3
16
480
1
VGA (85Hz)
1.6
2.2
17.8
1.6
VGA (85Hz)
3
25
480
1
SVGA (56Hz)
2.0
3.6
22.2
0.7
SVGA (56Hz)
2
22
600
1
SVGA (60Hz)
3.2
2.2
20.0
1.0
SVGA (60Hz)
4
23
600
1
SVGA (72Hz)
2.4
1.3
16.0
1.1
SVGA (72Hz)
6
23
600
37
SVGA (75Hz)
1.6
3.2
16.2
0.3
SVGA (75Hz)
3
21
600
1
SVGA (85Hz)
1.1
2.7
14.2
0.6
SVGA (85Hz)
3
27
600
1
Mac 16"mode
1.1
3.9
14.5
0.6
Mac 16"mode
3
39
624
1
XGA (60Hz)
2.1
2.5
15.8
0.4
XGA (60Hz)
6
29
768
3
XGA (70Hz)
1.8
1.9
13.7
0.3
XGA (70Hz)
6
29
768
3
XGA (75Hz)
1.2
2.2
13.0
0.2
XGA (75Hz)
3
28
768
1
1.0
2.2
10.8
0.5
XGA (85Hz)
3
36
768
1
1.2
2.4
10.7
0.6
1152×864 (75Hz)
3
32
864
1
1280×960 (60Hz)
1.0
2.9
11.9
0.9
1280×960 (60Hz)
3
36
960
1
1280×1024 (60Hz)
1.0
2.3
11.9
0.4
1280×1024 (60Hz)
3
38
1024
1
1280×1024 (75Hz)
1.1
1.8
9.5
0.1
1280×1024 (75Hz)
3
38
1024
1
1600×1200 (60Hz)
1.2
1.9
9.9
0.4
1600×1200 (60Hz)
3
46
1200
1
TECHNICAL
XGA (85Hz)
1152×864 (75Hz)
© 3M 2003. All Rights Reserved.
TECHNICAL - 3
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Connection to the Mouse Control
1. PS/2, ADB or Serial Mouse
(1) Turn off the projector and computer, and connect the two units with the appropriate cable. For
PS/2 mouse control (for IBM and compatible), use the enclosed mouse cable. For others, consult
your dealer.
(2) Disconnect the USB cable from the projector if it is connected. Then turn on the projector.
(3) Turn on the computer.
(4) Start the mouse function. If the mouse has not been started, reboot the computer (soft reboot or
reboot buttons). Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT button” of page 4.
2. USB Mouse
(1) Connect the projector and computer with a suitable commercially available USB cable. Consult
your dealer to get the cable, if you need.
(2) Start the mouse function. Refer to the descriptions of “DISC PAD” and “MOUSE/RIGHT
button” of page 4.
NOTE • Before connecting, read the instruction manuals of the devices to be connected.
• In the case of notebook type computers with an internal pointing device, the mouse control
function will not work unless the internal pointing device is disabled. In such case, disable the
internal pointing device and change the BIOS setting to select an external mouse before the
operations described in (1) to (4) above.
Also, some computers may not have a utility program to operate a mouse.
Refer to the computer hardware manual for detail.
PS/2 Mouse
Projector
CONTROL Terminal
CLK
DATA
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
SEL0
RTS
+5V
GND
TECHNICAL - 4
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1
2
3
4
5
6
© 3M 2003. All Rights Reserved.
DATA
GND
+5V
CLK
Mouse jack
Mini DIN 6-pin
6
5
3
4
2
1
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
ADB Mouse
Projector
CONTROL Terminal
DATA
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
RTS
+5V
GND
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Computer
1 ADB
2 (POWER ON)
3 +5V
4 GND
Mouse jack
Mini DIN 4-pin
3
4
1
2
Serial Mouse
CONTROL Terminal
D-sub 15-pin shrink jack
6
2 3 4 5
7 8 9 10
11 12 13 14 15
1
Projector
1
2
3
4
5
SEL0 6
RTS 7
8
9
GND 10
11
12
13
TD 14
15
1
2
3
4
5
6
7
8
9
Computer
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
Mouse jack
D-sub 9-pin
1
2
6
3
7
5
4
8
9
USB Mouse
2
3
1
4
Computer
Projector
+5V 1
1
+5V
—DATA 2
2 —DATA
+DATA 3
3
GND 4
USB jack
(A type)
+DATA
4 GND
1
2
3
4
USB cable
© 3M 2003. All Rights Reserved.
TECHNICAL - 5
TECHNICAL
USB jack
(B type)
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
RS-232C communication
(1) Turn off the projector and computer power supplies and connect with the RS-232C cable.
(2) Turn on the computer power supply and after the computer has started up, turn on the projector
power supply.
Projector
Computer
1
2
3
4
5
SELO 6
RTS 7
8
9
GND 10
11
12
RD 13
TD 14
15
Control jack
D-sub 15-pin shrink jack
5 4 3 2 1
10 9 8 7 6
15 14 13 12 11
1
2
3
4
5
6
7
8
9
CD
RD
TD
DTR
GND
DSR
RTS
CTS
RI
RS-232C jack
D-sub 9-pin
2
1
6
3
7
4
8
Communications setting
19200bps, 8N1
1 Protocol
Consist of header (7 bytes) + command data (6 bytes).
2 Header
BE + EF + 03 + 06 + 00 + CRC_low + CRC_high
CRC_low : Lower byte of CRC flag for command data.
CRC_high : Upper byte of CRC flag for command data.
3 Command data
Command data chart
byte_0
byte_1
byte_2
Action
low
byte_3
byte_4
Type
high
low
byte_5
Setting code
high
low
high
Action (byte_0 - 1)
Action
Classification
Content
1
SET
Change setting to desired value.
2
GET
Read projector internal setup value.
4
INCREMENT
Increment setup value by 1.
5
DECREMENT
Decrement setup value by 1.
6
EXECUTE
Run a command.
TECHNICAL - 6
© 3M 2003. All Rights Reserved.
5
9
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Requesting projector status (Get command)
(1) Send the request code Header + Command data (‘02H’+‘00H’+ type (2 bytes) +‘00H’+‘00H’)
from the computer to the projector.
(2) The projector returns the response code ‘1DH’+ data (2 bytes) to the computer.
Changing the projector settings (Set command)
(1) Send the setting code Header + Command data (‘01H’+‘00H’+ type (2 bytes) + setting code (2
bytes)) from the computer to the projector.
(2) The projector changes the setting based on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Using the projector default settings (Reset Command)
(1) The computer sends the default setting code Header + Command data (‘06H’+‘00H’+ type (2
bytes) +‘00H’+‘00H’) to the projector.
(2) The projector changes the specified setting to the default value.
(3) The projector returns the response code ‘06H’ to the computer.
Increasing the projector setting value (Increment command)
(1) The computer sends the increment code Header + Command data (‘04H’+‘00H’+ type (2 bytes)
+‘00H’+‘00H’) to the projector.
(2) The projector in creases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
Decreasing the projector setting value (Decrement command)
(1) The computer sends the decrement code Header + Command data (‘05H’+‘00H’+ type (2 bytes)
+‘00H’ + ‘00H’) to the projector.
(2) The projector decreases the setting value on the above setting code.
(3) The projector returns the response code ‘06H’ to the computer.
When a command sent by the projector cannot be understood by the computer
When the command sent by the projector cannot be understood, the error command ‘15H’ is
returned by the computer. Some times, the projector ignores RS-232C commands during other
works. If the error command ‘15H’ is returned, please send the same command again.
When data sent by the projector cannot be practice
NOTE • Operation cannot be guaranteed when the projector receives an undefined command or
data.
• Provide an interval of at least 40ms between the response code and any other code.
• The projector outputs test data when the power supply is switched ON, and when the lamp is lit.
Ignore this data.
• Commands are not accepted during warm-up.
© 3M 2003. All Rights Reserved.
TECHNICAL - 7
TECHNICAL
When the command sent by the projector cannot be practiced, the the error code ‘1cH’ +‘xxxxH’ is
returned.
When the data length is greater than indicated by the data length code, the projector will ignore the
excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an error code
will be returned to the projector.
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Command data chart
Names
Blank Color
Operation type
Set
Type
Setting code
Red
BE EF
03
06 00
3B D3
01 00
00 30
00 00
Orange
BE EF
03
06 00
AB D2
01 00
00 30
01 00
Green
BE EF
03
06 00
5B D2
01 00
00 30
02 00
Blue
BE EF
03
06 00
CB D3
01 00
00 30
03 00
Purple
BE EF
03
06 00
FB D1
01 00
00 30
04 00
White
BE EF
03
06 00
6B D0
01 00
00 30
05 00
Black
BE EF
03
06 00
9B D0
01 00
00 30
06 00
MyScreen
BE EF
03
06 00
FB CA
01 00
00 30
20 00
ORIGINAL
BE EF
03
06 00
FB E2
01 00
00 30
40 00
BE EF
03
06 00
08 D3
02 00
00 30
00 00
Get
Mirror
Set
Set
Menu Color
BE EF
03
06 00
C7 D2
01 00
01 30
00 00
BE EF
03
06 00
57 D3
01 00
01 30
01 00
V lnverse
BE EF
03
06 00
A7 D3
01 00
01 30
02 00
H&V Inverse
BE EF
03
06 00
37 D2
01 00
01 30
03 00
BE EF
03
06 00
F4 D2
02 00
01 30
00 00
Normal
BE EF
03
06 00
83 D2
01 00
02 30
00 00
Freeze
BE EF
03
06 00
13 D3
01 00
02 30
01 00
BE EF
03
06 00
B0 D2
02 00
02 30
00 00
Red
BE EF
03
06 00
7F D3
01 00
03 30
00 00
Orange
BE EF
03
06 00
EF D2
01 00
03 30
01 00
Green
BE EF
03
06 00
1F D2
01 00
03 30
02 00
Blub
BE EF
03
06 00
8F D3
01 00
03 30
03 00
Purple
BE EF
03
06 00
BF D1
01 00
03 30
04 00
Transparent
BE EF
03
06 00
2F D0
01 00
03 30
05 00
Gray
BE EF
03
06 00
DF D0
01 00
03 30
06 00
BE EF
03
06 00
4C D3
02 00
03 30
00 00
ORIGINAL
BE EF
03
06 00
0B D2
01 00
04 30
00 00
OFF
BE EF
03
06 00
9B D3
01 00
04 30
01 00
MyScreen
BE EF
03
06 00
CB CB
01 00
04 30
20 00
Get
BE EF
03
06 00
38 D2
02 00
04 30
00 00
English
BE EF
03
06 00
F7 D3
01 00
05 30
00 00
Français
BE EF
03
06 00
67 D2
01 00
05 30
01 00
Deutsch
BE EF
03
06 00
97 D2
01 00
05 30
02 00
Español
BE EF
03
06 00
07 D3
01 00
05 30
03 00
Italiano
BE EF
03
06 00
37 D1
01 00
05 30
04 00
Norsk
BE EF
03
06 00
A7 D0
01 00
05 30
05 00
Nederlands
BE EF
03
06 00
57 D0
01 00
05 30
06 00
Português
BE EF
03
06 00
C7 D1
01 00
05 30
07 00
Japanese
BE EF
03
06 00
37 D4
01 00
05 30
08 00
Get
BE EF
03
06 00
C4 D3
02 00
05 30
00 00
Get
Startup
Language
Set
Set
TECHNICAL - 8
Action
Normal
Get
Set
CRC
H Inverse
Get
Freeze
Command data
Header
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Command data chart
Operation type
Command data
Header
Type
Setting code
Get
BE EF
03
06 00
7C D2
02 00
07 30
00 00
Increment
BE EF
03
06 00
1A D2
04 00
07 30
00 00
Decrement
BE EF
03
06 00
CB D3
05 00
07 30
00 00
Get
BE EF
03
06 00
08 86
02 00
10 31
00 00
Increment
BE EF
03
06 00
6E 86
04 00
10 31
00 00
Decrement
BE EF
03
06 00
BF 87
05 00
10 31
00 00
Brightness Reset
Execute
BE EF
03
06 00
58 D3
06 00
00 70
00 00
Contrast Reset
Execute
BE EF
03
06 00
A4 D2
06 00
01 70
00 00
V.Position Reset
Execute
BE EF
03
06 00
E0 D2
06 00
02 70
00 00
H.Position Reset
Execute
BE EF
03
06 00
IC D3
06 00
03 70
00 00
H.Size Reset
Execute
BE EF
03
06 00
68 D2
06 00
04 70
00 00
Color Balance R Reset
Execute
BE EF
03
06 00
94 D3
06 00
05 70
00 00
Color Balance B Reset
Execute
BE EF
03
06 00
D0 D3
06 00
06 70
00 00
Sharpness Reset
Execute
BE EF
03
06 00
C4 D0
06 00
09 70
00 00
Color Reset
Execute
BE EF
03
06 00
80 D0
06 00
0A 70
00 00
Tint Reset
Execute
BE EF
03
06 00
7C D1
06 00
0B 70
00 00
Keystone_V Reset
Execute
BE EF
03
06 00
08 D0
06 00
0C 70
00 00
Keystone_H Reset
Execute
BE EF
03
06 00
98 D8
06 00
20 70
00 00
Auto
Execute
BE EF
03
06 00
91 D0
06 00
0A 20
00 00
off
BE EF
03
06 00
FB D8
01 00
20 30
00 00
on
BE EF
03
06 00
6B D9
01 00
20 30
01 00
BE EF
03
06 00
C8 D8
02 00
20 30
00 00
BE EF
03
06 00
D9 D8
02 00
20 60
00 00
Magnify
Auto off
Blank on/off
Set
Get
Error Status
(Example of Return)
00 00
01 00
(Normal) (Cover-error)
Get
04 00
(Temp-error)
Power
Set
Volume
Action
02 00
(Fan-error)
05 00
(Air flow-error)
03 00
(Lamp-error)
06 00
(Lamp-Time-over)
BE EF
BE EF
BE EF
03
03
03
06 00
06 00
06 00
2A D3
BA D2
19 D3
01 00
01 00
02 00
00 60
00 60
00 60
00 00
01 00
00 00
RGB1
BE EF
03
06 00
FE D2
01 00
00 20
00 00
OFF
ON
Get
Input Source
CRC
RGB2
BE EF
03
06 00
3E D0
01 00
00 20
04 00
Digital
BE EF
03
06 00
0E D2
01 00
00 20
03 00
Video
BE EF
03
06 00
6E D3
01 00
00 20
01 00
SVideo
BE EF
03
06 00
9E D3
01 00
00 20
02 00
Component
BE EF
03
06 00
AE D1
01 00
00 20
05 00
Get
BE EF
03
06 00
CD D2
02 00
00 20
00 00
Get
BE EF
03
06 00
31 D3
02 00
01 20
00 00
Increment
BE EF
03
06 00
57 D3
04 00
01 20
00 00
Decrement
BE EF
03
06 00
86 D2
05 00
01 20
00 00
Set
© 3M 2003. All Rights Reserved.
TECHNICAL - 9
TECHNICAL
Names
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Command data chart
Names
Mute
Operation type
Contrast
Color
Balance R
Color
Balance B
Keystone_V
Keystone_H
Aspect
Type
Setting code
Normal
BE EF
03
06 00
46 D3
01 00
02 20
00 00
Mute
BE EF
03
06 00
D6 D2
01 00
02 20
01 00
Get
BE EF
03
06 00
75 D3
02 00
02 20
00 00
Get
BE EF
03
06 00
89 D2
02 00
03 20
00 00
Increment
BE EF
03
06 00
EF D2
04 00
03 20
00 00
Decrement
BE EF
03
06 00
3E D3
05 00
03 20
00 00
Get
BE EF
03
06 00
FD D3
02 00
04 20
00 00
Increment
BE EF
03
06 00
9B D3
04 00
04 20
00 00
Decrement
BE EF
03
06 00
4A D2
05 00
04 20
00 00
Get
BE EF
03
06 00
01 D2
02 00
05 20
00 00
Increment
BE EF
03
06 00
67 D2
04 00
05 20
00 00
Decrement
BE EF
03
06 00
B6 D3
05 00
05 20
00 00
Get
BE EF
03
06 00
45 D2
02 00
06 20
00 00
Increment
BE EF
03
06 00
23 D2
04 00
06 20
00 00
Decrement
BE EF
03
06 00
F2 D3
05 00
06 20
00 00
Get
BE EF
03
06 00
B9 D3
02 00
07 20
00 00
Increment
BE EF
03
06 00
DF D3
04 00
07 20
00 00
Decrement
BE EF
03
06 00
0E D2
05 00
07 20
00 00
Get
BE EF
03
06 00
E9 D0
02 00
0B 20
00 00
Increment
BE EF
03
06 00
8F D0
04 00
0B 20
00 00
Decrement
BE EF
03
06 00
5E D1
05 00
0B 20
00 00
4:3
BE EF
03
06 00
9E D0
01 00
08 20
00 00
16:9
BE EF
03
06 00
0E D1
01 00
08 20
01 00
Small
BE EF
03
06 00
FE D1
01 00
08 20
02 00
BE EF
03
06 00
AD D0
02 00
08 20
00 00
Default
BE EF
03
06 00
62 D1
01 00
09 20
00 00
Bottom
BE EF
03
06 00
F2 D0
01 00
09 20
01 00
Top
BE EF
03
06 00
02 D0
01 00
09 20
02 00
Get
BE EF
03
06 00
51 D1
02 00
09 20
00 00
Get
BE EF
03
06 00
0D 83
02 00
00 21
00 00
Increment
BE EF
03
06 00
6B 83
04 00
00 21
00 00
Decrement
BE EF
03
06 00
BA 82
05 00
00 21
00 00
Get
BE EF
03
06 00
F1 82
02 00
01 21
00 00
Increment
BE EF
03
06 00
97 82
04 00
01 21
00 00
Decrement
BE EF
03
06 00
46 83
05 00
01 21
00 00
Get
BE EF
03
06 00
B5 82
02 00
02 21
00 00
Increment
BE EF
03
06 00
D3 82
04 00
02 21
00 00
Decrement
BE EF
03
06 00
02 83
05 00
02 21
00 00
Get
BE EF
03
06 00
49 83
02 00
03 21
00 00
Increment
BE EF
03
06 00
2F 83
04 00
03 21
00 00
Decrement
BE EF
03
06 00
FE 82
05 00
03 21
00 00
Set
Brightness
Set
Get
Display
Position at
16 : 9 or Small
V.Position
H.Position
H.Size
H.Phase
Command data
Header
Set
TECHNICAL - 10
CRC
© 3M 2003. All Rights Reserved.
Action
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Command data chart
Names
Operation type
Sharpness
Color
Tint
Set
Video Format
Type
Setting code
Get
BE EF
03
06 00
F1 72
02 00
01 22
00 00
Increment
BE EF
03
06 00
97 72
04 00
01 22
00 00
Decrement
BE EF
03
06 00
46 73
05 00
01 22
00 00
Get
BE EF
03
06 00
B5 72
02 00
02 22
00 00
Increment
BE EF
03
06 00
D3 72
04 00
02 22
00 00
Decrement
BE EF
03
06 00
02 73
05 00
02 22
00 00
Get
BE EF
03
06 00
49 73
02 00
03 22
00 00
Increment
BE EF
03
06 00
2F 73
04 00
03 22
00 00
Decrement
BE EF
03
06 00
FE 72
05 00
03 22
00 00
Auto
BE EF
03
06 00
9E 75
01 00
00 22
0A 00
NTSC
BE EF
03
06 00
FE 71
01 00
00 22
04 00
PAL
BE EF
03
06 00
6E 70
01 00
00 22
05 00
SECAM
BE EF
03
06 00
6E 75
01 00
00 22
09 00
NTSC 4.43
BE EF
03
06 00
5E 72
01 00
00 22
02 00
M-PAL
BE EF
03
06 00
FE 74
01 00
00 22
08 00
N-PAL
BE EF
03
06 00
0E 71
01 00
00 22
07 00
Get
Set
Video NR
CRC
Action
BE EF
03
06 00
0D 73
02 00
00 22
00 00
off
BE EF
03
06 00
B6 73
01 00
06 22
00 00
on
BE EF
03
06 00
26 72
01 00
06 22
01 00
BE EF
03
06 00
85 73
02 00
06 22
00 00
Get
Set
Command data
Header
off
BE EF
03
06 00
4A 72
01 00
07 22
00 00
TV
BE EF
03
06 00
DA 73
01 00
07 22
01 00
FILM
BE EF
03
06 00
2A 73
01 00
07 22
02 00
Progressive
Get
BE EF
03
06 00
79 72
02 00
07 22
00 00
off
BE EF
03
06 00
5E 71
01 00
08 22
00 00
on
BE EF
03
06 00
CE 70
01 00
08 22
01 00
Set
Black
Get
HDTV
BE EF
03
06 00
6D 71
02 00
08 22
00 00
1080i
BE EF
03
06 00
F2 73
01 00
05 22
00 00
1035i
BE EF
03
06 00
62 72
01 00
05 22
01 00
Set
Get
Set
BE EF
03
06 00
C1 73
02 00
05 22
00 00
off
BE EF
03
06 00
FE 22
01 00
00 23
00 00
Large
BE EF
03
06 00
6E 23
01 00
00 23
01 00
Small
BE EF
03
06 00
9E 23
01 00
00 23
02 00
BE EF
03
06 00
Cd 22
02 00
00 23
00 00
Get
© 3M 2003. All Rights Reserved.
TECHNICAL - 11
TECHNICAL
PinP Size
3M™ Multimedia Projector MP8795
TECHNICAL (continued)
Command data chart
Names
Operation type
Set
PinP Position
Type
Setting code
Upper left
BE EF
03
06 00
02 23
01 00
01 23
00 00
Upper right
BE EF
03
06 00
92 22
01 00
01 23
01 00
bottom left
BE EF
03
06 00
62 22
01 00
01 23
03 00
bottom right
BE EF
03
06 00
F2 23
01 00
01 23
02 00
Get
PinP Audio ch
Set
Zoom
Sync on G
WHISPER
Action
BE EF
03
06 00
31 23
02 00
01 23
00 00
BE EF
03
06 00
BA 22
01 00
03 23
00 00
Video
BE EF
03
06 00
2A 23
01 00
03 23
01 00
BE EF
03
06 00
89 22
02 00
03 23
00 00
Video
BE EF
03
06 00
D6 22
01 00
02 23
01 00
S-Video
BE EF
03
06 00
26 22
01 00
02 23
02 00
Component
BE EF
03
06 00
16 20
01 00
02 23
05 00
Get
BE EF
03
06 00
75 23
02 00
02 23
00 00
Increment
BE EF
03
06 00
6A 93
04 00
00 24
00 00
Decrement
BE EF
03
06 00
BB 92
05 00
00 24
00 00
Increment
BE EF
03
06 00
96 92
04 00
01 24
00 00
Decrement
BE EF
03
06 00
47 93
05 00
01 24
00 00
off
BE EF
03
06 00
CB D0
01 00
08 30
01 00
on
BE EF
03
06 00
5B D1
01 00
08 30
00 00
Get
BE EF
03
06 00
68 D1
02 00
08 30
00 00
NORMAL
BE EF
03
06 00
3B 23
01 00
00 33
00 00
WHISPER
BE EF
03
06 00
AB 22
01 00
00 33
01 00
Get
BE EF
03
06 00
08 23
02 00
00 33
00 00
NORMAL
BE EF
03
06 00
C7 F0
01 00
A1 30
00 00
CINEMA
BE EF
03
06 00
57 F1
01 00
A1 30
01 00
DYNAMIC
BE EF
03
06 00
A7 F1
01 00
A1 30
02 00
6500K
BE EF
03
06 00
37 F0
01 00
A1 30
03 00
BE EF
03
06 00
F4 F0
02 00
A1 30
00 00
Set
FOCUS
CRC
RGB
Get
PinP Input
Command data
Header
Set
Set
Set
GAMMA
Get
TECHNICAL - 12
© 3M 2003. All Rights Reserved.
3M™ Multimedia Projector MP8795
Intended Use
Before operating this machine, please read this entire manual thoroughly. The 3MTM Multimedia Projectors are designed, built, and tested for use indoors,
using 3M lamps, 3M ceiling mount hardware, and nominal local voltages.
The use of other replacement lamps, outdoor operation, or different voltages has not been tested and could damage the projector peripheral equipment
and/or create a potentially unsafe operating condition.
3M Multimedia projectors and Wall Display Systems are designed to operate in a normal office environment.
• 16˚ to 29˚C (60˚ to 85˚ F)
• 10- 80 %RH (without condensation)
• 0- 1828 m (0-6000 feet) above sea level
The ambient operating environment should be free of airborne smoke, grease, oil and other contaminates that can affect the operation or performance of the
projector.
Use of this product in adverse conditions will void the product warranty.
Let us help you make the most of your next presentation. We offer everything from presentation supplies to tips for better meetings. And we're the only
transparency manufacturer that offers a recycling program for your used transparencies. For late-breaking news, handy reference and free product samples, call
us toll-free in the continental United States and Canada, 24 hours a day, or visit our Internet Website.
3M Austin Center
Building A145-5N-01
6801 River Place Blvd.
Austin, TX 78726-9000
3M Canada
P.O. Box 5757
London, Ontario
N6A 4T1
3M Mexico, S.A. de C.V.
Apartado Postal 14-139
Mexico, D.F. 07000
Mexico
3M Europe
Boulevard de l'Oise
95006 Cerge Pontoise Cedex
France
© 3M 2003. All Rights Reserved.
Litho in Japan
© 3M 2003
78-6970-9175-5 Rev. A
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement