Manual - Martin Professional
P/N 35010030-F
READ AND SAVE THESE INSTRUCTIONS
Magnum 2500Hz
user manual
Dimensions/Legal
All dimensions are in millimeters
© 2016 Martin Professional™ ApS. Information subject to change without notice. Martin Professional and all
affiliated companies disclaim liability for any injury, damage, direct or indirect loss, consequential or economic loss or
any other loss occasioned by the use of, inability to use or reliance on the information contained in this manual.
Martin™, Harman™ and all other trademarks in this document pertaining to services or products by Martin
Professional or its affiliates and subsidiaries are registered as the property of Harman International Industries.
Martin Professional™ ApS • Olof Palmes Allé 18 • 8200 Aarhus N • Denmark • www.martin.com
2
Dimensions/Legal
Dimensions/Legal .......................................................................................................... 2
Safety information .......................................................................................................... 4
Product overview ........................................................................................................... 7
Product description
Features at a glance
Product details
7
7
8
Quick Start ..................................................................................................................... 9
Setting up
Making haze
9
9
Installation and setting up ........................................................................................... 10
Location
AC power
Setting up
Final checks
Turning on the power
10
10
11
12
12
Control settings ............................................................................................................ 13
Overview
Continuous Run Mode
Setting the Automatic Timer
Setting the “one-shot” timer
What the status lights mean
13
13
13
14
16
DMX control ................................................................................................................. 17
Overview
Connection
DMX functions
Setting the DMX address
17
17
17
18
Approved Fluid Types.................................................................................................. 19
Basic service ................................................................................................................ 20
Cleaning
Pro Clean Supreme
Fuse replacement
20
20
21
Shutting down the machine ......................................................................................... 22
Shutdown procedure
Long term storage instructions
22
22
Optional accessories ................................................................................................... 23
Fitting the DMX decoder module
23
Troubleshooting ........................................................................................................... 24
Technical Specifications .............................................................................................. 25
Notes ............................................................................................................................ 27
Dimensions/Legal
3
Safety information
The following symbols are used to identify important safety information:
Caution! Safety
hazard. Risk of
personal injury.
Caution! Burn
hazard. Hot
surface. Do not
touch.
Danger!
Hazardous
voltage. Contact
will cause electric
shock.
Caution! Fire
hazard.
Warning! This product is not for household use. It presents risks of injury due to
electric shock, burns, falls and respiratory problems!
Before operating the machine – Read and retain these Instructions
Avant l'opération – Lire et conserber ces instructions
Observe all warnings in this manual and printed on the machine. Use the system
only as described in this manual and in accordance with local laws and
regulations.
If you have questions about how to operate the machine safely, or if you have
followed the instructions in this manual and the machine is malfunctioning,
please contact Martin Service.
P r e ve n t i n g e l e ct ri c s h o c k s
4
•
Always ground (earth) the machine electrically.
•
Use only a source of AC power that complies with local building and
electrical codes, and that has both overload and ground-fault protection.
•
Before connecting the Magnum 2500Hz to power, check that the
voltage indicated on the machine’s serial label matches your local AC
power voltage. If your AC power voltage does not match, do not use the
machine. Contact Martin Service for assistance.
•
Before using the machine, check that all power distribution equipment
and cables are in perfect condition and rated for the current
requirements of all connected devices.
•
If the machine or any cables connected to it are in any way damaged,
defective, wet, or show signs of overheating, stop using the machine
and contact Martin Service for assistance. If the supply cord is
damaged, it must be replaced by a special cord or assembly available
from the manufacturer or it’s service agent.
•
Disconnect the machine from AC power before servicing and when not
in use.
•
This system is not waterproof and should not be exposed to wet
outdoor conditions. Do not immerse in water or any other liquid. Do not
expose to high-pressure water jets.
Safety information
•
Do not spill fluid over or inside the machine. If fluid is spilled, disconnect
AC power and clean with a damp cloth. If fluid is spilled onto electronic
parts, take the system out of service and contact Martin for advice.
•
Do not remove the covers or attempt to repair a faulty machine. Refer
any service not described in this manual to Martin.
•
Do not operate the machine if any parts are damaged, defective or
missing.
•
Moisture and electricity do not mix. Do not aim the haze output at
electrical connections or devices.
P r e ve n t i n g b u r n s an d f i r e
•
The haze produced by the machine is hot enough to cause burns when
it leaves the nozzle, and very hot droplets of fluid escape occasionally.
Keep people and objects at least 1 meter (39 inches) away from the
haze output nozzle.
•
Do not touch the haze output nozzle during or after use – it becomes
extremely hot and remains hot for several hours after the machine has
been shut down.
•
Haze output contains glycol, a flammable alcohol that burns with an
almost invisible blue flame. Do not point haze output at sources of
ignition such as open flames or pyrotechnic effects.
•
Do not attempt to bypass thermostatic switches, fluid sensors or fuses.
•
Replace fuses only with ones of the type and rating specified in this
manual for the machine.
•
Provide a minimum free space of 100 mm (4 in.) around the machine.
•
Provide a minimum free space of 500 mm (20 in.) around fans and air
vents and ensure free and unobstructed air flow to and around the
machine.
•
Keep the machine at least 600 mm (24 in.) away from combustible and
heat-sensitive materials.
•
Do not operate the machine if the ambient temperature (Ta) is below 5°
C (41° F) or above 40° C (104° F).
•
Do not operate the machine if the relative air humidity exceeds 80%.
P r e ve n t i n g i n j u ri e s
•
Ensure that the surface on which the machine is located or installed can
safely hold the weight of the machine.
•
Do not install the machine over areas where people are present.
•
This appliance is not intended for use by persons (including children)
with reduced physical sensory or mental capabilities, or lack of
experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for
their safety. Children should be supervised to ensure that they do not
play with the appliance.
•
Haze machines can cause condensation. Do not point the output at
smooth floors. Floors and surfaces may become slippery. Check these
frequently and wipe dry as necessary to avoid any danger of slipping.
•
Ensure at least 2m visibility in areas where haze is being produced.
•
Haze fluid contains food-grade glycols in solution but may present
health risks if swallowed. Do not drink it. Store it securely. If eye contact
Safety information
5
occurs, rinse with water. If fluid is swallowed, give water and obtain
medical advice.
P r e ve n t i n g b r e at h i n g p r o b l em s
6
•
A haze machine can operate safely only with the haze fluid it is
designed for. Use the machine only with fluids specified under
“Approved Fluid Types” on page 19 or you may cause the release of
toxic gases, presenting a severe health hazard. You will also probably
damage the machine.
•
Do not create dense haze in confined or poorly ventilated areas.
•
Do not expose people with health problems (including allergic and/or
respiratory conditions such as asthma) to haze output.
•
Do not point haze output directly at a person’s face or at face height.
Safety information
Product overview
Product description
The Magnum 2500Hz from Martin provides a uniquely flexible and convenient
solution to a wide range of atmospheric requirements whether permanently
installed or taken on the road.
The machine features a unique new design that encompasses what the
Magnum range is all about: state of the art technology, high quality and
ruggedness.
Congratulations on your purchase of the Magnum 2500Hz from Martin. Details
of the full range of Martin products are available on our website at
www.martin.com.
Features at a glance
•
•
•
•
•
•
•
•
•
•
Proportional haze & fan output
Continuous output
Timer remote control included
Output and density level control
Internal remote control storage
Concealed 3.8 l fluid reservoir
Fluid-out sensing
Uses economical RUSH Haze Fluid™
Optional DMX interface
Machine link mode - up to 4 units can be operated at the same time with one
remote.
Product overview
7
Product details
Heat (Red) /
Ready (Green)
indicators
Remote /
machine link
sockets
DMX address
selection switches
Power inlet
plug
Main power
switch
DMX through
socket
DMX input
plug
Hinged door to
concealed fluid
compartment
Fluid level gauge
Haze output nozzle
Warning, high
temperature vapour and
surfaces!
8
Product overview
Quick Start
You are no doubt eager to switch on the machine and try it out by making a lot
of haze. This section tells you how to do that. However, please also make the
time to read the safety and servicing instructions in the remainder of this
manual.
Setting up
Locate the machine in a suitably large area with nothing in front of the haze
output.
Fill the fluid tank with Martin approved haze fluid (see page 19). The fluid
compartment is opened by pulling outwards on the cover (pull using a finger in
the round hole).
Connect the machine to a suitably rated power source. The power requirements
are:
EU Models – 920 W, 220-240 V
US Models – 920 W, 100-130 V
Connect the remote control to the REMOTE IN connector on the rear panel.
Turn on the power switch. The red Heat indicator on the remote and the rear of
the unit will light. After about 6-8 minutes the green Ready indicator on the
remote and the rear of the unit will light. The machine is then ready to produce
haze. To obtain maximum haze output, wait another couple of minutes for the
Heat indicator to go out.
Making haze
Once the machine has heated up, press the FOG button on the remote to start
the haze output. The green ON light will come on. Press the FOG button again
to turn off the haze.
You can set the haze density by turning the knob. If the knob is turned fully
counter-clockwise, no haze will be produced.
Quick Start
9
Installation and setting up
DANGER! DO NOT operate the Magnum 2500Hz until you have read and
observed all the precautions listed under “Safety information” on page 4.
Location
The Magnum 2500Hz should be located on a solid surface such as the floor.
The machine can operate in any orientation from 30 degrees upwards to 30
degrees downwards. Steeper tilting may cause fluid leakage.
Do not suspend the machine over areas where people will be underneath.
Ensure that there is at least 100 mm (4 in.) clearance around the machine and at
least 600 mm (24 in.) in front of the haze output.
AC power
Before using the machine, ensure that a grounding-type (earthed) power plug
that fits the local power outlets is installed on the power cable.
DANGER! Make sure the power plug is correctly rated:
• For EU models fit with a plug rated at 6 A minimum.
• For US models fit with a plug rated at 15 A minimum.
When installing the plug, follow the plug manufacturer’s instructions and
connect pins as follows:
yellow and green wire to ground (earth), blue wire to neutral and brown wire to
live.
The table below shows some common pin identification schemes.
wire
function
marking
screw colour
brown
live
“L”
yellow or brass
blue
neutral
“N”
silver
green/yellow
earth
green
Before connecting the Magnum 2500Hz to power, verify that the AC supply is
adequately dimensioned for the current draw of the machine. The machine
requires:
EU Models – 920 W, 220-240 V
US Models – 920 W, 100-130 V
Check that the local AC voltage is appropriate, as indicated on the machine’s
serial number label. If your AC voltage is outside the appropriate range, do not
use the machine. Contact Martin Service for assistance.
10
Installation and setting up
Setting up
Fill the fluid tank with Martin approved haze fluid (see page 19). The fluid
compartment is opened by pulling outwards on the cover (pull using a finger in
the round hole). The cover is held closed by a magnetic catch and hinges
upwards.
If the optional DMX input is fitted and DMX control is being used, connect the
machine to the DMX line (see page 17).
Connect the remote to the REMOTE IN socket on the back panel.
If you are operating several machines using the machine-to-machine link
function, connect up the machines in a daisy-chain using RJ45 (computer
network) type cables. The maximum total length of cable, including the remote
cable, is 50 m (164 ft.).
To additional
machines
Do not connect a computer network to the RJ45 remote / link sockets on the
Magnum 2500Hz. Although the connectors are compatible, the electrical signals
are not, and equipment may be damaged.
Installation and setting up
11
Final checks
Before applying power to the Magnum 2500Hz, verify the following:
• the machine is safely located or installed and meets the location
requirements stated on page 10.
•
the operator is familiar with, and able to comply with, the requirements
for safe operation listed on page 4.
•
the haze fluid is genuine Martin fluid listed under “Approved fluid
•
types” on page 19.
•
the machine is electrically grounded (earthed).
•
the AC power distribution circuits and lines are adequately rated for the
current load.
Turning on the power
Turn on the main power switch located next to the power cable inlet.
The red Heat indicator on the remote and on the rear of the machine will light for
about 6-8 minutes as the machine heats up to operating temperature.
When the green Ready indicator comes on, the machine is ready to make haze.
To obtain maximum output, wait another few minutes for the red Heat
indicator to go off, as haze output is reduced while the unit is heating
up.
12
Installation and setting up
Control settings
Overview
Output level / timer
programming knob
Machine ready to fog
light
Machine heating light
Fog / Timer engage
button
Timer On light
Timer Off light
Timer set button
The unit is controlled using the remote control. You can control it in these ways:
•
Automatic Continuous run mode.
•
Automatic haze bursts using a repeating timer
•
You trigger a timed burst of haze using the “one-shot” timer
You can also set the haze output level using the knob.
Continuous Run Mode
Press the FOG button once (for less than one second) to enter continuous run
mode or timer mode. If the timer is set, the timer mode will run automatically,
otherwise continuous mode will be enabled and the machine will produce haze
until the button is pressed again. The green timer LED will light when in
continuous run mode.
Setting the Automatic Timer
The Automatic Timer allows you to set the machine to keep producing timed
bursts of haze without anyone having to press any buttons. You need to set two
times: the run/on time during which the machine will produce haze, and the
wait/off time during which the machine will idle.
Control settings
13
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF – 255 seconds).
3. Press the TIMER SET button once. The ON light will come on static and
the OFF light will flash. You are now setting the Off/Wait time.
4. Turn the knob to the required “wait” time.
5. Press the TIMER SET button once more. Both ON/OFF lights will come
on to show the timer is programmed.
The run and wait times are now stored and will be remembered even after the
unit has been switched off.
To start the timer using the times you’ve set, press the FOG / TIMER ENGAGE
button briefly. To turn off the timer, press the FOG / TIMER ENGAGE button
briefly again. When the timer is engaged, the ON light will come on during the
On/Run time and the OFF light will come on during the Off/Wait time.
If you only want to change the Off/Wait time, leaving the On/Run time
unchanged, press TIMER SET twice. This will take you directly to
setting the Off time without changing the On time.
To find out what the current time settings are, press TIMER SET then rotate the
knob slowly until the “ON” light begins to flash very rapidly. The knob is now set
to the current run/on time. Press TIMER SET once and rotate the knob slowly
again until the “OFF” light begins to flash very rapidly. The knob is now set to
the current wait/off time. Press TIMER SET again to get back to normal.
Setting the “one-shot” timer
The “one shot” timer allows you to pre-program the length of the haze burst.
This can be useful if you want to have a fixed-time burst of haze which you can
repeat at will by pressing the haze button.
1. Press the TIMER SET button. The ON light will flash. You are now
setting the On/Run time.
2. Turn the knob to the required “run” time, as shown on the outer scale of
the knob (OFF – 255 seconds).
3. Press the TIMER SET button once. The ON light will come on and the
OFF light will flash.
4. Turn the knob fully right to where “OS” (“One Shot”) is marked.
5. Press the TIMER SET button once more.
The timer is now programmed to one-shot mode and this will be remembered
even after the unit has been switched off.
To produce a timed burst of haze, press the FOG button briefly. To stop the
timed haze output early, press the FOG button briefly again.
14
Control settings
Priming the machine after fluid out
If the machine runs out of fluid, it may not pump properly after refilling the fluid
due to airlocks in the fluid pipes.
To prime the machine, hold down the FOG button and turn the knob to
maximum. Keep the button held until the haze output is strong and steady. Then
turn the knob back to the required output level and release the FOG button.
During PRIME mode the machine will prime for 10seconds if any
airlock is still visible on the fluid line, prime machine again until the
haze output is continuous. Note that you must turn the knob to start
the prime process.
If the machine is left to run when out of fluid, damage may be caused to the
pump leading to premature pump failure. The automatic fluid sensing system will
shut the machine down within approximately 5 minutes of running dry.
Control settings
15
What the status lights mean
The four lights on the remote have the following functions. The red “HEAT” light
and the green “READY” light are also duplicated on the rear of the machine
itself.
HEAT+READY
meaning
no lights
Machine is not powered, or remote is not connected.
heat
Machine is heating but is not yet up to operating
temperature.
heat + ready
Machine is heating and has reached minimum operating
temperature. Haze output level may be reduced while
heating.
ready
Machine has finished heating and is at full operating
temperature.
If the ready LED is flashing, refer to the following code
table.
ready flashing
16
Single pulse
Calibration Error
Double pulse
Fluid-Out Error
Triple pulse
Overheat Error
OFF+ON
meaning
no lights
Timer is disabled
both on
Timer is programmed but not enabled
“OFF” lit
Timer is running, currently in Off/Wait period
“ON” lit
Timer is running, currently in On/Run period or continuous
mode
“ON” flashing
The timer “ON” time is currently being programmed
“ON” lit, “OFF”
flashing
The timer “OFF” time is currently being programmed
Control settings
DMX control
Overview
DMX is a digital control system widely used in entertainment and architectural
lighting. Any controller meeting the DMX-512A standard may be used to control
and program the haze output of the Magnum 2500Hz.
The Magnum 2500Hz requires the optional DMX control module to allow DMX
operation.
Connection
The Magnum 2500Hz provides a 3-pin XLR plug and socket on the rear panel
for DMX connection. The wiring is shown below.
Connector pin
function
1
Ground
2
Data – (“Cold”)
3
Data + (“Hot”)
For best results, use cable designed for high speed digital data transmission.
DMX functions
The Magnum 2500Hz operates from a single DMX channel which gives
proportional control of haze density from 0-100%.
DMX Level
function
0 – 29
No haze
30 – 255
Haze at variable density, (30=minimum, 255=maximum)
When the machine is receiving valid DMX data, the indicator light next to the
address switches will light.
It is possible to control the machine by DMX and using the remote control at the
same time, the highest setting will take precedence.
No provision is made for resetting the fluid out condition via the DMX system.
Reset this using the remote or by powering down the machine to perform a full
reset.
Note that the last switch (switch 10) on the DMX address setting dipswitch is
used for the test function not address 512. Setting this switch to ‘on’ will
produce a timer (10 second) burst of haze allowing the machine to be tested
without the remote control being present.
DMX control
17
Setting the DMX address
Each unit on a DMX system must be allocated an address so that the DMX
controller can send separate commands to the unit. On the Magnum 2500Hz,
the DMX address is set using the bank of switches (“dip switches”) on the back
panel next to the DMX connectors. The switch settings for each possible DMX
address are given in the table below.
DIP-Switch Setting
0 = OFF
1 = ON
18
#1
#2
#3
#4
#5
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
#9
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
#8
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
#7
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
#6
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
336
337
338
339
340
341
342
343
344
345
346
347
348
349
350
351
352
353
354
355
356
357
358
359
360
361
362
363
364
365
366
367
368
369
370
371
372
373
374
375
376
377
378
379
380
381
382
383
384
385
386
387
388
389
390
391
392
393
394
395
396
397
398
399
400
401
402
403
404
405
406
407
408
409
410
411
412
413
414
415
416
417
418
419
420
421
422
423
424
425
426
427
428
429
430
431
432
433
434
435
436
437
438
439
440
441
442
443
444
445
446
447
448
449
450
451
452
453
454
455
456
457
458
459
460
461
462
463
464
465
466
467
468
469
470
471
472
473
474
475
476
477
478
479
480
481
482
483
484
485
486
487
488
489
490
491
492
493
494
495
496
497
498
499
500
501
502
503
504
505
506
507
508
509
510
511
DMX control
Approved Fluid Types
The following types of Martin haze fluid are suitable for use in this machine.
Martin supplies high quality haze fluids that are based on ultra-pure deionized
water. Use only the following genuine Martin haze fluids. No other fluid is
suitable for use.
DANGER! The Magnum 2500Hz can run safely only on the specific haze fluids it
is designed for. Use ONLY the Martin haze fluids designated in this manual.
NEVER use any other type of fluid, or toxic gas may be produced. You will
probably also cause damage to the system that is not covered by the product
warranty. Do not dilute haze fluid with water or any other liquid. Discard haze
fluid if it becomes contaminated.
RUSH Haze Fluid™
RUSH Haze Fluid™ is a specially formulated water-based haze formula and is
recommended for use with applicable Martin haze effect generators. It gives a
fine, optically transparent airborne medium with a light-to-medium index of
refraction that is ideal for beam and aerial FX projections. RUSH Haze Fluid is
designed as an economy fluid that is suitable for use in nightclubs, bars, stage
and outdoor events
“Calibration factors have been developed and approved by the Actors’ Equity Association
and the Broadway League for use in measuring theatrical haze with the Magnum
2500Hz™ and RUSH Haze Fluid™.
Approved Fluid Types
19
Basic service
Before servicing the Magnum 2500Hz, read and observe all the precautions
listed in “Safety information” on page 4. Any service not described in this section
must be carried out by a Martin service technician.
Cleaning
Excessive dust, haze fluid, and dirt build up will degrade performance and
cause overheating and damage to the machine that is not covered by the
product warranty. To maintain adequate cooling, dust must be cleaned from the
outer casing and air vents of the machine periodically.
Isolate the machine from power and allow to cool completely before cleaning.
The haze output nozzle remains hot for up to 10 hours after use.
•
Remove dust from the air vents with a soft brush, cotton swab, vacuum,
or compressed air.
•
Clean haze fluid residues from the haze output of the machine using a
damp cloth.
•
Clean the outer casing with a damp cloth only.
Pro Clean Supreme
Specially designed for optimum performance while providing longevity of the heat
exchanger, Pro Clean Supreme is the ultimate cleaning solution for Martin fog and haze
effect machines. Applying Pro Clean Supreme fluid on a regular basis reduces clogging and
further extends the life of Martin Fog and Haze machines.
Using Pro Clean Supreme every 200 hours, or once a month (depending on usage), will
prolong the life of the heat exchanger in Martin fog and haze machines. Connect Pro Clean
Supreme fluid to the fogger or hazer, then allow the unit to heat. When fully ready, activate
the machine or remote for approximately 30-45
minutes (use the timer function if available). When completed, replace cleaning fluid with
appropriate fluid.
Note: Cleaning procedure should be used if the unit is to be stored for 30 days or more.
Ensure there is no fluid in the fluid tube when placing in storage.
20
Basic service
Fuse replacement
The main fuse for the Magnum 2500Hz is located on the electronics board
inside the unit.
DANGER! Disconnect the power supply before removing any covers. Live parts
inside!
To replace the fuse, disconnect the power cord from the supply, unscrew the
screws holding the top cover of the unit and remove the cover. The electronics
board is located at the back of the unit near the remote control sockets.
Remove the fuse holder cover and pull out the fuse. Remove the spent fuse and
replace with one of exactly the same size and rating. The fuse type is indicated
below. Contact Martin Service if the fuse blows repeatedly.
F1
EU Models = 6.3 AT (slow-blow), 250 V
US Models = 10 AT (slow-blow), 125 V
F2
All models = 3.15AT
Basic service
21
Shutting down the machine
IMPORTANT: To ensure both the performance and life of your Magnum 2500Hz
is maximised, the following procedures should always be followed.
Shutdown procedure
When shutting down the machine, always allow a 5-minute period with the
output set at zero, before removing the power.
Long term storage instructions
When the machine is expected to be out of use for more than 7 days you must
drain the fluid system. To do this follow the following sequence of operations:
•
•
•
•
•
22
Switch on the machine and wait for the operating temperature to be
reached (Green ‘ready’ LED will illuminate)
Remove the fluid feed pipe from the fluid bottle, and invert it while
holding it above the machine.
Prime the machine repeatedly until no more haze is emitted.
Replace the fluid pipe in the bottle, and allow the machine to reheat
(very important) for at least five minutes.
Remove the power from the machine and place into storage.
Shutting down the machine
Optional accessories
Fitting the DMX decoder module
The optional DMX decoder replaces the blanking plate on the rear of the
Magnum 2500Hz.
DANGER! Disconnect the power supply before removing the blanking plate. Live
parts inside!
1. Remove and keep safe the two screws holding in the blanking plate,
and remove the plate.
2. Locate the DMX interface ribbon cable inside the rear of the unit and
plug onto the connector on the DMX interface circuit board (PL5).
3. If you cannot locate the ribbon cable, you will need to remove the main
covers of the unit. The ribbon cable connects the main circuit board to
the DMX interface.
4. Fit the new DMX module into the rear panel and tighten the screws.
5. Refit any covers you have removed before reconnecting the power
supply.
Optional accessories
23
Troubleshooting
Problem
Probable cause(s)
Suggested remedy
Machine not at operating
temperature
Wait 10 to 15 minutes
Machine not powered up or
heaters disabled
Ensure mains power switch
on, enable heaters by
pressing FOG
Output level control set to
zero
Increase setting
Timer is engaged
Disengage the timer by
pressing the FOG/TIMER
ENGAGE button briefly
DMX address setting
incorrect
Change DMX address (page
17)
Poor connection in DMX line
Check DMX cables and
connections
Haze output is weak
Machine requires priming
Prime machine (page 15)
Wet, greasy, non-uniform
haze output, fluid drips or
spits from nozzles, or very
loud noise when firing
machine
Incompatible haze fluid
Use only approved fluid!
Mains fuse blown
Replace fuse (page 21)
No power at AC cable inlet
Check power cable and
circuit breaker
Internal error
Check fault codes in status
light table.
Machine will not produce
haze when remote control
Fog button pressed
Machine continues to
produce haze when Fog
button is not pressed
Machine can be fired from
the remote control, but not
by DMX controller
Machine appears dead
Ready LED flashing
24
Troubleshooting
Technical Specifications
P h ys i c a l
Length ............................................................................................ 455 mm (18 in.)
Width ........................................................................................... 285 mm (11.3 in.)
Height .......................................................................................... 286 mm (11.1 in.)
Weight, dry ................................................................................... 11.9 kg (26.3 lb.)
Weight, filled ................................................................................. 15.7 kg (34.6 lb.)
P e r f o r m a nc e
Coverage volume ......................................................... 2500m3 (88,287 ft3) minute
Fluid consumption (max.) ......................................................... 10.5 ml per minute
Continuous effect output
Ready time ........................................................................................... 6-8 minutes
C o n t r o l a n d pr o g r am mi n g
Control options .................. Included timer remote control, optional analog DMX,
................................................................................................. machine link mode
Control parameters ................................... Continuous or timer controlled output
Haze and fan ............................... Proportionally controlled haze and fan, 0-100%
DMX channels ...................................................................................................... 1
DMX compliance .................................................. ANSI E1.11 – USITT DMX512-A
Construction
Housing .................................................................................. Steel and aluminium
Color ..............................................................................................Black and silver
Heat exchanger ............................................................900 W, thermally protected
Blower fan ..................................................................... Integrated, 200-2800 RPM
Fluid pump .......................................................... Oscillating piston, high pressure
Fluid reservoir ........................ 3.8 l concealed reservoir with quick-connect fitting
Fluid management ............................. Fluid out sensing, sealed for transportation
........................................................................................... visual fluid level gauge
Remote control .... Includes 3 m (9.8 ft.) lead terminated to RJ45, internal storage
I n s t al l at i o n
Mounting ...................................................................................................Standing
Orientation ................................................................ Up to +/- 30° from Horizontal
Clearance around machine.............................................................. 100 mm (4 in.)
Connections
AC Power ................................................................................. IEC male inlet, C14
Optional DMX in/out .................................................................... 3-pin locking XLR
Remote control, machine link in/out ............................................................... RJ45
E l e c t ri c a l
EU Model
AC Power .............................................................................. 220-240 V, 50-60 Hz
Main fuse ......................................................................... 6.3 AT (slow-blow), 250V
Typical power and current .............................................................. 920 W, 4.15 A*
US Model
AC Power .............................................................................. 100-130 V, 50-60 Hz
Main fuse .......................................................................... 10 AT (slow-blow), 125V
Typical power and current ................................................................... 920 W, 8 A*
*Measurements made at nominal voltage. Allow for a deviation of +/- 10%
Technical Specifications
25
Th e r m a l
Maximum ambient temperature (Ta max) .......................................... 40° C (104° F)
Minimum ambient temperature (Ta Min) ............................................... 5° C (41° F)
Exterior surface temperature, steady state ........................................ 40° C (104° F)
Maximum nozzle temperature.......................................................... 200° C (392° F)
Ap p r o va l s
EU Model
EU safety: ................................................................. EN 60 335-1+A15, EN 62233
EU EMC:..............................................................................................EN 61000-6-3
EU Immunity:.......................................................................................EN 61000-6-1
Australia/NZ (pending): ..................................................................................... RCM
US Model
US safety ................................................................................................. UL Std.998
Canada safety ....................................................................... CSA C22.2 No.104-01
“Calibration factors have been developed and approved by the Actors’ Equity
Association and the Broadway League for use in measuring theatrical Haze with
the Magnum 2500Hz and RUSH Haze Fluid™.”
Included Items
Fluid reservoir, 3.8 l: .......................................................................... P/N 34300537
Power input cable, EU, IEC C13 female, stripped ends, 1.5 m (4.9 m): ..................
........................................................................................................... P/N 11501012
Power input cable, US, IEC C13 female, molded NEMA 5-15P, 3 m (9.84 m): .......
........................................................................................................... P/N 11501502
Timer remote control .......................................................................... P/N 92765033
User manual ....................................................................................... P/N 35010030
Ac c e s s o r i e s
Martin™ Magnum 2500Hz, DMX interface ......................................... P/N 91612011
Approved Fluids
RUSH Haze Fluid™
JEM™ Pro Clean Supreme
*Various sizes available - contact your dealer or see martin.com for more details.
Service Tools
Epsilon 5 AVR Programmer ............................................................... P/N 50502004
Temperature Calibration Box ............................................................. P/N 92620005
O r d e ri n g i n f or m at i o n
Martin™ Magnum 2500Hz, EU ........................................................... P/N 92225450
Martin™ Magnum 2500Hz, US ........................................................... P/N 92225400
26
Technical Specifications
Notes
Notes
27
28
Notes
29
30
Disposing of this product
Martin™ products are supplied in compliance with Directive 2002/96/EC of the European
Parliament and of the Council of the European Union on WEEE (Waste Electrical and
Electronic Equipment), as amended by Directive 2003/108/EC, where applicable.
Help preserve the environment! Ensure that this product is recycled at the end of its life.
Your supplier can give details of local arrangements for the disposal of Martin products.
31
Martin Professional A/S,Olof Palmes Allé 18, DK-8200,Aarhus N
Phone: +45 87 40 00 00 Internet: www.martin.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement