HP 3PAR Installation guide
HP 3PAR StoreServ File Controller Quick Start Guide Table 1 Network information (clustered system) (continued) Supported storage systems Network device These installation instructions apply to the HP 3PAR StoreServ File Controller, which is based on the HP ProLiant DL380p Gen8 server platform. IMPORTANT: Read this document first. Table 2 Network information (standalone system) Network device Restrictive Active Directory environments If the 3PAR StoreServ system is placed in a restrictive Active Directory environment, it may require pre-staging Active Directory objects or certain administrative permissions. See the following Microsoft articles for more information: Record network information It is critical to have the correct networking information available before proceeding with the system installation and configuration. It may be necessary to pre-stage DNS information. Contact your system administrator to clarify network configuration requirements. • How to Create a Cluster in a Restrictive Active Directory environment • Failover Cluster Step-by-Step Guide: Configuring Accounts in Active Directory Ping the domain controller from Node 2. Ping the IP address ping <node 2 address> of Node 2 from Node 1. Use Table 1 (page 1) or Table 2 (page 1), depending on your system configuration, to document your network information before proceeding with system setup. Ping the name of ping <node 2 name> Node 2 from Node ping <node 2 fqdn> 1. Table 1 Network information (clustered system) Ping the IP address ping <node 1> of Node 1 from Node 2. IP address Node 1 iLO Ping the name of ping <node1 name> Node 1 from Node ping <node1 fqdn> 2. Node 2 iLO Node 1 Page 1 ping <domain controller name> Verify the network pingpath <domain path to the domain controller address> controller and DNS pingpath <domain servers is correct. controller name> pingpath <DNS server name> (repeat for each DNS server) Table 4 Validation tests (standalone system) Test Table 3 Validation tests (clustered system) Command(s) to execute ping <domain controller address> pingpath <DNS server address> (repeat for each DNS server) Complete the tests in Table 3 (page 1) or Table 4 (page 1), depending on your configuration, to verify network connectivity. Consult with your network administrator to confirm test results. Test ping <domain controller name> ping <domain controller fqdn> Confirm that the IP address and names are not already in use. The HP 3PAR StoreServ File Controller requires a minimum of 6 IP addresses. These addresses may be statically assigned or assigned by a DHCP server or both. If you are using static addressing or a DHCP server that does not automatically update DNS, ensure that both forward and reverse DNS information (A and PTR records) is pre-staged in the DNS server. ping <domain controller address> ping <domain controller fqdn> Validate network information IMPORTANT: Before joining the 3PAR StoreServ system nodes to the Active Directory domain, ensure that there is network connectivity between each node and the domain controller. Successful? (Y/N) Verify forward and nslookup <node 2 reverse DNS address> information for nslookup <node 2 name> Node 2 is correct. nslookup <node 2 fqdn> Ping the domain controller from Node 1. iLO The Microsoft Windows Storage Server 2012 Standard Edition operating system is preinstalled and activated on all systems. Fully qualified DNS name (FQDN) IP address System IMPORTANT: Included with your storage system is the HP Storage System Recovery DVD. This DVD is used to restore the system to factory defaults. Keep this DVD in a safe place. Network device Fully qualified DNS name (FQDN) Command(s) to execute Verify forward and nslookup <node 1 reverse DNS address> information for nslookup <node 1 name> Node 1 is correct. nslookup <node 1 fqdn> First file server http://www.hp.com/go/proliantgen8/docs *C8S69-96001* IP address Cluster For details and specifications, see the HP 3PAR StoreServ File Controller QuickSpecs available at: For general information about HP ProLiant Gen8 servers, go to: HP Part Number: C8S69-96001 Published: June 2013 Edition: 2 Test Node 2 http://www.hp.com/go/3PARStoreServ © Copyright 2013 Hewlett-Packard Development Company, L.P. Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. Fully qualified DNS name (FQDN) Table 3 Validation tests (clustered system) (continued) Successful? (Y/N) Command(s) to execute Ping the IP address ping <system address> of the StoreEasy system from another system on the same network. Ping the IP address ping <system address> of some other system on the same network form the StoreEasy system. Ping the name of the StoreEasy system from another system on the same network. ping <node1 name> ping <node1 fqdn> Successful? (Y/N) Table 4 Validation tests (standalone system) (continued) Test Command(s) to execute Ping the name of some other system on the same network form the StoreEasy system. ping <node1 name> 3. Successful? (Y/N) ping <node1 fqdn> If you will be adding the StoreEasy system to an Active Directory domain, some additional tests include: Ping the domain controller from the StoreEasy system. ping <domain controller address> You can deploy the product as a standalone system, or use multiple systems to deploy a Windows failover cluster. If you are setting up a cluster configuration, you must connect a cable between the servers to complete the initial setup. Connect a cable between the ports identified as callout 1 in Figure 1, which enables you to create a simplified two-node cluster later in the HP Initial Configuration Tasks (ICT) window. If more than two nodes are desired in the cluster, create the two–node cluster first, then add nodes later. 3. 4. 5. NOTE: By default, iLO obtains the management IP address and subnet mask from your network’s DHCP server. The hostname found on the iLO tag is automatically registered with your network’s DNS server. Figure 1 Connecting the servers ping <domain controller name> 6. Verify the network pingpath <domain path to the domain controller address> controller and DNS pingpath <domain servers is correct. controller name> pingpath <DNS server address> (Repeat for each DNS server) 2. Install the rail kit by following the HP Rack Rail Kit Installation Instructions, which is packaged with the rail kit. Install the storage system into the rack. 3. After installation completes and the server (or servers if deploying a cluster) reboots, you are automatically logged on as the local administrator (using the default Windows Administrator password of HPinvent!). If you are deploying a cluster, continue to work only with the server on which you used the Setup Windows Wizard. The HP Initial Configuration Tasks (ICT) window launches automatically at logon. The tasks presented vary depending on whether you have chosen to deploy a standalone system or a cluster. For more information on any of these tasks, click the help icon for the appropriate task group in the ICT window. IMPORTANT: HP strongly recommends that you validate your configuration when using clusters. Whether you create a cluster through the ICT or the Failover Cluster Manager, one of the first steps is validating your configuration using the Microsoft cluster validation tool. If you choose to skip the validation step, you can still validate the cluster after it is created. http://www.hp.com/support/manuals Regulatory information Access the storage system Use either the direct attach or remote management method to connect to the storage system. Power on and complete the configuration 1. IMPORTANT: Only the direct attach and remote management access methods can be used to install the storage system. After the storage system installation process is complete and the server’s IP addresses have been assigned, you can then additionally use the remote desktop method to access the storage system. Install the storage system hardware 1. Using the default user information provided on the iLO Network Settings tag, log on to iLO, and then launch a remote console to the storage system. For detailed instructions about using each of these access methods, see the HP 3PAR StoreServ File Controller Administrator Guide or the HP iLO 4 User Guide, which you can search for (by product name) at: pingpath <DNS server name> (Repeat for each DNS server) Additionally, verify that the DNS information is valid for the cluster and file server. HP recommends that you also verify the iLO IP address and name resolution; however, this is not critical to support the cluster and file server. Connect a power cable to the storage system. Locate the iLO Network Settings tag attached to the storage system and record the default user name, password, and DNS name. From a remote computer, open a standard Web browser and enter the iLO management hostname of the storage system. • IMPORTANT: If you are deploying a cluster, only interact with one of the servers. After powering on both servers, the Setup Windows Wizard and the Initial Configuration Tasks must be run from only one server. Direct attach —This access method is mandatory if your network does not have a Dynamic Host Configuration Protocol (DHCP) server. Connect the following cables to the back panel of the storage system in the following sequence: keyboard, mouse, network cables, monitor cable, and power cable. NOTE: The keyboard, mouse, and monitor are not provided with the storage system. • Power on the system by pushing the power button on the front panel. If using iLO, click Momentary Press under the Power Switch menu of the remote console. 2. Remote management—Access the storage system using the Integrated Lights-Out (iLO) remote management method: 1. Connect the desired network cables to network adapter ports on the back of the storage system. 2. Connect a network cable to the iLO port located on the back of the storage system. Page 2 The storage system starts and displays the Setup Windows wizard, in which you select language and regional settings and accept the license agreement. After completing the wizard, you are asked if you want to configure a standalone system or a two-node cluster. Click Yes to configure your system as a cluster or click No to configure your system as a standalone server. The storage system installation process takes approximately 10–15 minutes. For important safety, environmental, and regulatory information, see Safety and Compliance Information for Server, Storage, Power, Networking, and Rack Products, available at http://www.hp.com/support/ Safety-Compliance-EnterpriseProducts. Documentation feedback Send any errors, suggestions, or comments to Documentation Feedback ([email protected]).
* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project