HP | 7000 dl Router Series | Installation manual | HP 7000 dl Router Series Installation Manual

Installation Guide
ProCurve Secure Router 7102dl
ProCurve Secure Router 7203dl
61195880L1-34E
ProCurve Secure Router
Installation Guide
J8752A
ProCurve Secure Router 7102dl
J8753A
ProCurve Secure Router 7203dl
J8451A
ProCurve Secure Router 1xT1 Interface Module
J8452A
ProCurve Secure Router 1xT1 + DSX-1 Interface Module
J8453A
ProCurve Secure Router 2xT1 Interface Module
J8454A
ProCurve Secure Router 1xE1 Interface Module
J8455A
ProCurve Secure Router 1xE1 + G.703 Interface Module
J8456A
ProCurve Secure Router 2xE1 Interface Module
J8457A
ProCurve Secure Router 2xISDN BRI S/T Interface Module
J8458A
ProCurve Secure Router 1xSerial Interface Module
J8459A
ProCurve Secure Router 1xADSL2+ Annex A Interface Module
J8759A
ProCurve Secure Router 1xADSL2+ Annex B Interface Module
J8460A
ProCurve Secure Router ISDN BRI U Backup Module
J8461A
ProCurve Secure Router ISDN BRI S/T Backup Module
J8462A
ProCurve Secure Router Analog Modem Backup Module
J8463A
ProCurve Secure Router 8xT1/E1 Wide Module
J8471A
ProCurve Secure Router 7100/7200 IPSec Module
J9010A
ProCurve Secure Router 2xISDN BRI U Interface Module
J9011A
ProCurve Secure Router 8xSerial Wide Module
J9026A
ProCurve Secure Router 7100/7200 IPSec Base Module
5990-8878
61195880L1-34E
May 2006
Copyright
ProCurve Secure Router Installation Guide
Copyright
Copyright 2006 Hewlett-Packard Development Company, LP. The information contained herein is subject
to change without notice.
This document contains proprietary information, which is protected by copyright. No part of this document
can be photocopied, reproduced, or translated into another language without the prior written consent of
Hewlett-Packard.
Trademarks
CompactFlash is a registered trademark of the CompactFlash Association (CFA).
Any brand names and product names included in this manual are trademarks, registered trademarks, or
trade names of their respective holders.
Software Licensing Agreement
Use of the software is subject to the HP Software License terms. A copy of the HP Software License is
included in the product package and can be found on the ProCurve SROS Documentation CD.
Disclaimer
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO
THIS MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be
liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Hewlett-Packard assumes no responsibility for the use or reliability of its software on equipment that is not
furnished by Hewlett-Packard.
Warranty
See the Customer Support/Warranty booklet included with the product.
A copy of the specific warranty terms applicable to your Hewlett-Packard products and replacement parts
can be obtained from your HP Sales and Service Office or authorized dealer.
4
Copyright 2006 Hewlett-Packard Development Company, LP
5990-8878
ProCurve Secure Router Installation Guide
Table of Contents
Table of Contents
Introduction to the ProCurve Secure Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ProCurve Secure Router 7102dl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
ProCurve Secure Router 7203dl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Unpack and Inspect the System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Physical Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reviewing the Front Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Reviewing the Rear Panel Design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear Panel Interfaces . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15
15
17
17
Option Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Interface Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xT1 + DSX-1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xT1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xE1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xE1 + G.703 Drop and Insert Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xE1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xSerial Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex A Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex B Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI S/T Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI U Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8xT1/E1 Wide Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8xSerial Wide Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Backup Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN BRI U Backup Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ISDN S/T Backup Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Modem Backup Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
20
21
22
23
24
25
26
27
28
29
30
32
33
33
34
35
Unit Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tools Required . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Mounting Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding the Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding Requirements Statement. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Interface and Backup Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing the Encryption Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing a CompactFlash® Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1/E1 Mode Dip-Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplying Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Supplying Redundant Power to the Unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
36
36
37
37
38
38
40
40
40
41
41
Connector Pin Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Safety and Regulatory Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Waste Electrical And Electronic Equipment (Weee) Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
5
Table of Contents
6
ProCurve Secure Router Installation Guide
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Hardware Installation Guide
List of Figures
List of Figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
Figure 12.
Figure 13.
Figure 14.
Figure 15.
Figure 16.
Figure 17.
Figure 18.
Figure 19.
5990-3760
ProCurve Secure Router 7102dl Front Panel Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCurve Secure Router 7203dl Front Panel Layout. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCurve Secure Router 7102dl Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ProCurve Secure Router 7203dl Rear Panel Layout . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xT1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xT1 + DSX-1 Interface Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xT1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xE1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xE1 + G.703 Drop and Insert Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xE1 Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xSerial Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex A Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex B Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI S/T Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI U Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8xT1/E1 Wide Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8xSerial Wide Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Grounding the ProCurve Secure Router . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installing Backup Module and Interface Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copyright 2006 Hewlett-Packard Development Company, LP
15
15
17
17
19
20
21
22
23
24
25
26
27
28
29
30
32
38
39
7
ProCurve Secure Router Installation Guide
List of Tables
List of Tables
Table 1.
Table A-1.
Table A-2.
Table A-3.
Table A-4.
Table A-5.
Table A-6.
Table A-7.
Table A-8.
Table A-9.
Table A-10.
Table A-11.
Table A-12.
Table A-13.
5990-3760
ProCurve Secure Router LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONSOLE Port (DTE) Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10/100BaseT Ethernet Port Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E1 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DSX-1 Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
G.703 Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1xSerial Interface and 8xSerial Wide Module Connector Pinouts . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex A Interface Module Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . .
1xADSL2+ Annex B Interface Module Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI S/T Interface Module Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2xISDN BRI U Interface Module Connector Pinouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Analog Modem and ISDN BRI U Backup Modules Connector Pinouts . . . . . . . . . . . . . . .
ISDN BRI S/T Backup Module Connector Pinouts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Copyright 2006 Hewlett-Packard Development Company, LP
15
43
43
44
44
44
45
45
46
46
46
46
47
47
8
1.
INTRODUCTION TO THE PROCURVE SECURE ROUTER
This installation guide describes the ProCurve Secure Router, details basic functionality, gives installation
instructions, and lists hardware specifications. For more information on router configuration for a specific
application, refer to the supplemental documents provided on your ProCurve SROS Documentation CD.
The router can be managed and configured through the command line interface CLI (accessible via the
VT100 (Console connection) or Telnet) or through the Graphical User Interface (GUI), using a Web
browser. These two methods are described in the Quick Start Guide provided with your router. For detailed
information on the CLI, refer to the SROS Command Line Interface Reference Guide, also on the CD. The
GUI is contains integrated help and various wizards to facilitate configuration. The Console port is
enabled by default, with no configured password.
The ProCurve Secure Router is a mid-range IP router designed for medium- to large-office connectivity
over Frame Relay or point-to-point (PPP) networks. This modular platform offers a complete solution for
access routing and WAN connectivity in a single, compact package. The main base units support a variety
of interchangeable interface modules and backup modules. The ProCurve Secure Router base units include
the following:
ProCurve Secure Router 7102dl
•
•
•
•
•
•
1U-high housing, rack-mountable, metal enclosure
Two module (card) slots
Two built-in Ethernet ports
Console port
Encryption Module slot
Compact Flash slot
ProCurve Secure Router 7203dl
•
•
•
•
•
•
•
1U-high housing, rack-mountable, metal enclosure
Three module (card) slots (two small, one wide)
Two built-in Ethernet ports
Console port
Encryption Module slot
Compact Flash slot
Redundant power supply (RPS) option
The interface modules in this series provide the following WAN connectivity options:
•
•
•
•
•
•
•
•
•
•
•
T1/FT1
T1/FT1 + DSX-1
Dual T1
E1/FE1
E1/FE1 + G.703 Drop
Dual E1/FE1
Dual ISDN BRI (U and S/T)
Serial (V.35/X.21)
ADSL (Annex A and Annex B)
Octal Serial Wide Module
Octal T1/E1 Wide Module (no external CSU/DSU needed)
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
9
Introduction to the ProCurve Secure Router
ProCurve Secure Router Installation Guide
If needed, an ISDN BRI U Backup Module, ISDN BRI S/T Backup Module, or Analog Modem Backup
Module can plug onto any narrow interface module, providing backup capability. Refer to Installing
Interface and Backup Modules on page 38 for more details.
For VPN applications using the ProCurve Secure Router, the optional 7100/7200 IPSec Module and
7100/7200 IPSec Base Module provide or activate encryption/decryption and security services. Refer to
Installing the Encryption Module on page 40. The installation of the optional encryption module enables
the software features associated with the VPN services.
Features
The ProCurve Secure Routers have the following features:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Modular network interface via module (card) slots
1U-high metal chassis with two or three slots for option modules
Two integrated 10/100BaseT Ethernet ports (RJ-45 with auto-MDIX)
Layer 2 WAN Protocol: Frame Relay, Multilink Frame Relay, PPP, Multilink PPP, HDLC
Integrated IP router with bridging
RIP Versions 1 and 2, OSPF, and BGP
IP encapsulation over Frame Relay (RFC1490)
Secure Router Operating System (SROS) Command Line Interface (CLI)
SNMP management
Web GUI
Integrated EIA-232 DTE configuration port (DB-9)
Optional backup modules available
Optional 7100/7200 IPSec Module and 7100/7200 IPSec Base Module provide encryption/decryption
and security services
Front panel LEDs
Mountable in a 19-inch rack
Worldwide auto-ranging AC power supply
Specifications
The ProCurve Secure Routers have the following specifications:
Physical
10
ProCurve Secure Router 7102dl
ProCurve Secure Router 7203dl
Width
44.25 cm (17.42 in)
44.25 cm (17.42 in)
Depth
29.26 cm (11.52 in)
29.26 cm (11.52 in)
Height
4.39 cm (1.73 in)
4.39 cm (1.73 in)
Weight
4.66 kg (10.26 lbs)
4.98 kg (10.95 lbs)
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Introduction to the ProCurve Secure Router
Electrical
ProCurve Secure Router 7102dl
ProCurve Secure Router 7203dl
AC Voltage
100 to 127/200 to 240 volts
100 to 127/200 to 240 volts
Maximum Current
0.4 A/0.2 A
0.8 A/0.4 A
Frequency Range
50 to 60 Hz
50 to 60 Hz
Environmental
ProCurve Secure Router 7102dl
ProCurve Secure Router 7203dl
Operating
Temperature
0°C to 50°C (32°F to 122°F)
0°C to 50°C (32°F to 122°F)
Non-Operating
Temperature
-20°C to 70°C (-4°F to 158°F)
-20°C to 70°C (-4°F to 158°F)
Relative Humidity
(noncondensing)
Up to 95 percent at 30°C (86°F)
Up to 95 percent at 30°C (86°F)
Non-Operating
Relative Humidity
(noncondensing)
Up to 95 percent at 30°C (86°F)
Up to 95 percent at 30°C (86°F)
Maximum Altitude
3.05 km (10,000 ft)
3.05 km (10,000 ft)
Unpack and Inspect the System
Each ProCurve Secure Router unit is shipped in its own cardboard shipping carton. Open each carton
carefully, and avoid deep penetration into the carton with sharp objects.
After unpacking the unit, inspect it for possible shipping damage. If the equipment has been damaged in
transit, immediately file a claim with the carrier and contact your local HP representative or reseller.
Contents of Shipments
ProCurve Secure Router 7000dl (7102dl and 7203dl)
Shipments of the ProCurve Secure Router 7000dl include the following items:
•
•
•
•
•
•
•
ProCurve Secure Router 7000dl base unit
Racking hardware
ProCurve SROS Documentation CD
Installation Guide
Quick Start Guide
Software License, Warranty, and Support documentation
Console cable, power cord
ProCurve Secure Router dl 1xT1 Module
Shipments of the 1xT1 Module include the following items:
•
•
•
1xT1 Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
11
Introduction to the ProCurve Secure Router
ProCurve Secure Router Installation Guide
ProCurve Secure Router dl 1xT1 + DSX-1 Module
Shipments of the 1xT1 + DSX-1 Module include the following items:
•
•
•
1xT1 + DSX-1 Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable
ProCurve Secure Router dl 2xT1 Module
Shipments of the 2xT1 Module include the following items:
•
•
•
2xT1 Interface Module
Quick Start Guide
Two 15-foot RJ-45 to RJ-45 cables
ProCurve Secure Router dl 1xE1 Module
Shipments of the 1xE1 Module include the following items:
•
•
•
1xE1 Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable
ProCurve Secure Router dl 1xE1 + G.703 Module
Shipments of the 1xE1 + G.703 Module include the following items:
•
•
•
1xE1 + G.703 Interface Module
Quick Start Guide
15-foot RJ-45 to RJ-45 cable
ProCurve Secure Router dl 2xE1 Module
Shipments of the 2xE1 Module include the following items:
•
•
•
2xE1 Interface Module
Quick Start Guide
Two 15-foot RJ-45 to RJ-45 cables
ProCurve Secure Router dl 2xISDN BRI S/T Module
Shipments of the 2xISDN BRI S/T Module include the following items:
•
•
•
2xISDN BRI Interface Module
Quick Start Guide
7-foot RJ-45 to RJ-11 cable
ProCurve Secure Router dl 2xISDN BRI U Module
Shipments of the 2xISDN BRI U Module include the following items:
•
•
•
12
2xISDN BRI U Interface Module
Quick Start Guide
7-foot RJ-45 to RJ-11 cable
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Introduction to the ProCurve Secure Router
ProCurve Secure Router dl 1xSerial Module
Shipments of the 1xSerial Module include the following items:
•
•
1xSerial Interface Module
Quick Start Guide
Cables for the 1xSerial module must be ordered separately: V.35 DTE (J8757A) or X.21
DTE (J8755A).
Note
ProCurve Secure Router dl 1xADSL2+ Annex A Module
Shipments of the 1xADSL2+ Annex A Module include the following items:
•
•
•
1xADSL2+ Annex A Interface Module
Quick Start Guide
7-foot RJ-11 to RJ-11 cable
ProCurve Secure Router dl 1xADSL2+ Annex B Module
Shipments of the 1xADSL2+ Annex B Module include the following items:
•
•
•
1xADSL2+ Annex B Interface Module
Quick Start Guide
7-foot RJ-11 to RJ-45 cable
ProCurve Secure Router dl ISDN BRI U Backup Module
Shipments of the ISDN BRI U Backup Module include the following items:
•
•
•
ISDN BRI U Backup Module
Quick Start Guide
7-foot RJ-11 to RJ-45 cable
ProCurve Secure Router dl ISDN BRI S/T Backup Module
Shipments of the ISDN BRI S/T Backup Module include the following items:
•
•
•
ISDN BRI S/T Backup Module
Quick Start Guide
7-foot RJ-11 to RJ-45 cable
ProCurve Secure Router dl Analog Modem Backup Module
Shipments of the Analog Modem Backup Module include the following items:
•
•
•
Analog Modem Backup Module
Quick Start Guide
7-foot RJ-11 to RJ-45 cable
ProCurve Secure Router dl Wide 8xT1/E1 Wide Module
Shipments of the 8xT1/E1 Wide Module include the following items:
•
•
•
8xT1/E1 Wide Interface Module
Quick Start Guide
Eight 15-foot RJ-45 to RJ-45 cables
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
13
Introduction to the ProCurve Secure Router
ProCurve Secure Router Installation Guide
ProCurve Secure Router dl 8xSerial Wide Module
Shipments of the 8xSerial Wide Module include the following items:
•
•
8xSerial Wide Interface Module
Quick Start Guide
Cables for the 8xSerial Wide Module must be ordered separately: V.35 DTE (J8757A) or
X.21 DTE (J8755A).
Note
ProCurve Secure Router dl 7100/7200 IPSec Module
Shipments of the 7100/7200 IPSec Module include the following items:
•
•
7100/7200 IPSec Module
Quick Start Guide
ProCurve Secure Router dl 7100/7200 IPSec Base Module
Shipments of the 7100/7200 IPSec Base Module include the following items:
•
•
7100/7200 IPSec Base Module
Quick Start Guide
Caution
14
Option modules are to be serviced by qualified service personnel only.
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
2.
Physical Description
PHYSICAL DESCRIPTION
Reviewing the Front Panel Design
Figure 1 shows the ProCurve Secure Router 7102dl front panel. Figure 2 shows the
ProCurve Secure Router 7203dl front panel. The pictures show the chassis with modules installed.
ACTIVITY LED
LINK LED
Eth 0/2
ProCurve 7102dl
Secure Router
J8752A
Slots
1
2
Stat
Stat
Bkp
Bkp
Power
Console
Fault
Tx
Tx
Rx
Rx
Eth 0/1
dl
dl
Figure 1. ProCurve Secure Router 7102dl Front Panel Layout
ProCurve 7203dl
Secure Router
J8753A
Power
Fault
Console
Eth 0/2
Slots
1
2
3
Stat
Stat
Stat
Bkp
Bkp
Act
Tx
Tx
Test
Rx
Rx
Eth 0/1
dl
dl
dl
wide
Figure 2. ProCurve Secure Router 7203dl Front Panel Layout
Front Panel Switches, Interfaces, and LEDs
Table 1 describes the front panel LEDs.
Table 1. ProCurve Secure Router LEDs
LED
Power
Fault
Slot 1/Slot 2 Stat
5990-3760
Color
Indicates that…
Off
The AC power input is off. Fault LED flashes slowly if RPS backup
power is on.
Green (flashing)
Unit is powering up. On power-up, the Power LED flashes if self-test
fails.
Green (solid)
Power is on and self-test passed.
Off
Operation is normal.
Orange (flashing)
A fault condition exists:
One or more cooling fans have failed.
AC power is not being received or internal primary AC/DC
converter has failed.
One or more option modules have failed.
Off
No interface module is installed, or interface is administratively down.
Green (solid)
Link is up and everything is operational.
Red (solid)
Current alarm condition is present on the WAN interface, or there is a
self-test failure. The LED illuminates if an interface is configured and in
the “no shutdown” condition, but a valid physical network connection
has not yet been established.
Yellow (solid)
Unit is in test.
Copyright 2006 Hewlett-Packard Development Company, LP
15
Physical Description
ProCurve Secure Router Installation Guide
Table 1. ProCurve Secure Router LEDs (Continued)
LED
Color
Indicates that…
Slot 1/Slot 2 Bkp
Off
No backup module is installed.
Green (solid)
Backup module is ready. For the ISDN BRI backup module, green solid
indicates that the negotiation with the switch is complete.
Green (flashing)
Backup is active.
Red (solid)
An alarm condition is occurring on the backup interface, or there is a
self-test failure. An interface is configured and in the “no shutdown”
condition, but a valid physical network connection has not yet been
established.
Yellow (solid)
Unit is in test.
Slot 1/Slot 2 - Tx/ Off
Rx
Green (flashing)
Slot 3 - Stat
(7203dl only)
Off
There is no activity on the WAN or backup interface.
There is activity on the WAN or backup interface.
Module is not installed.
Green (solid)
Module is recognized by the system.
Red (solid)
An alarm condition is occurring on the module interface.
Slot 3 - Act
(7203dl only)
Off
There is no data activity on the module.
Green (flashing)
There is data activity on the module.
Slot 3 - Test
(7203dl only)
Off
Module is not in test.
Yellow (solid)
Module is in test mode.
ETH 0/1 Link
Off
10/100BaseT Ethernet connection is inactive.
Green (solid)
10/100BaseT Ethernet connection is active.
ETH 0/2 Activity
Off
No Tx or Rx data is present.
Yellow (flashing)
Tx or Rx data is present.
Console Interface
The Console interface is an EIA-232 serial port (DTE) which provides for local management and
configuration (via a DB-9 female connector). Table A-1 on page 43 shows the Console port pinouts.
Note
Connection directly to an external modem requires a straight-through cable.
10/100BaseT Ethernet Interface and Activity LEDs
The Ethernet ports (Eth 0/1, Eth 0/2) are RJ-45 connectors with LEDs. The yellow activity LED flashes
when data traffic is being sent or received on the Ethernet port. The green link LED is on when the router
has a good connection to the LAN. Refer to Table A-2 on page 43 for the Ethernet port pinouts. The
Ethernet port provides the following:
•
•
•
•
•
10BaseT or 100BaseT with a single connector
Auto-negotiation
CSMA/CD
IEEE 802.3 compatibility
Auto-MDIX
Module Card Slots
The module card slots support various network plug-in cards. These card options are described in the
section Option Modules on page 18.
16
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Physical Description
Reviewing the Rear Panel Design
Figure 3 shows the ProCurve Secure Router 7102dl rear panel. Figure 4 shows the ProCurve Secure Router
7203dl rear panel.
Figure 3. ProCurve Secure Router 7102dl Rear Panel Layout
ProCurv
e SR IPSec Module
J8471A
Figure 4. ProCurve Secure Router 7203dl Rear Panel Layout
Rear Panel Interfaces
Encryption Module Slot
This slot supports the 7100/7200 IPSec Module (part number J8471A) and the 7100/7200 IPSec Base
Module (J9026A). These modules are designed to be used in the ProCurve Secure Router to activate
encryption/decryption and security services.
The 7100/7200 IPSec Module (J8471A) provides the following security services to the host processor:
DES, triple-DES(3DES), AES, SHA-1, MD5, and random number generation. Performance metrics
include 528 Mbps (DES), 176 Mbps (3DES), and 422 Mbps (AES). The power consumption of the card
does not exceed 2 watts. See Installing the Encryption Module on page 40 for installation instructions.
The 7100/7200 IPSec Base Module (J9026A) activate software encryption/decryption and security
services for IPSec VPNs. The card activates the following software security services in the host processor:
DES, triple-DES (3DES), AES, SHA-1, MD5, and random number generation.The power consumption of
the card does not exceed 1 watt. See Installing the Encryption Module on page 40 for installation
instructions.
Compact Flash Slot
This slot supports any Type 1 CompactFlash® card (16 MB to 1GB). See Installing a CompactFlash®
Card on page 40.
Redundant Power Supply (RPS) Input
This input supports a backup power supply for the unit with the use of the ProCurve 600 Redundant and
External Power Supply (J8168A). See Supplying Redundant Power to the Unit on page 41.
Power Supply
The ProCurve Secure Router has a worldwide auto-ranging AC power supply with an IEC connector. The
appropriate three-prong cable is included in the shipment. Please refer to Supplying Power to the Unit on
page 41 for connection details.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
17
Option Modules
3.
ProCurve Secure Router Installation Guide
OPTION MODULES
Note
ProCurve Secure Router option modules are not hot-swappable. Disconnect power from
the base unit before installing or removing modules.
The ProCurve Secure Router accepts several option modules designed to meet a variety of networking
requirements. The option modules are of three types: plug-in interface modules, plug-on backup modules,
and wide modules.
Interface modules are cards which plug directly into the option module slots located on the front of the
base unit. These cards provide the following types of interfaces:
•
•
•
•
•
•
•
•
•
•
•
1xT1 Interface Module on page 19
1xT1 + DSX-1 Interface Module on page 20
2xT1 Interface Module on page 21
1xE1 Interface Module on page 22
1xE1 + G.703 Drop and Insert Interface Module on page 23
2xE1 Interface Module on page 24
1xSerial Interface Module on page 25
1xADSL2+ Annex A Interface Module on page 26
1xADSL2+ Annex B Interface Module on page 27
2xISDN BRI S/T Interface Module on page 28
2xISDN BRI U Interface Module on page 29
Wide modules are cards which plug directly into the wide module slot located on the front of the base unit.
Two wide modules are available for use with the ProCurve Secure Router 7203dl:
•
•
8xT1/E1 Wide Module on page 30
8xSerial Wide Module on page 32
Backup modules are plug-on cards which plug directly on to the interface module prior to installation into
the base unit. A backup module must be plugged on to an interface module in order for the backup port on
the interface module to be active. The ProCurve Secure Router supports three different backup modules
(only two can be installed simultaneously):
•
•
•
ISDN BRI U Backup Module on page 33
ISDN S/T Backup Module on page 34
Analog Modem Backup Module on page 35
This section describes each module, providing individual card specifications and features. Refer to
Connector Pin Definitions on page 43 for pinout information. Installing Interface and Backup Modules on
page 38 provides information on card installation.
18
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
Interface Modules
1xT1 Interface Module
The 1xT1 Interface Module (see Figure 5) provides a T1 (full T1 or fractional T1) WAN interface for
the ProCurve Secure Router. Refer to Table A-3 on page 44 for the T1 connector pinouts, and refer to
Table A-12 on page 47 for the backup connector pinouts. An optional backup module is required for
backup applications.
Figure 5. 1xT1 Interface Module
Features and Specifications
•
Operating Modes
•
•
•
T1/FT1 Frame Relay/Multilink Frame
Relay
T1/FT1 PPP/Multilink PPP
T1/FT1 HDLC
T1/FT1 Interface
•
•
•
•
•
•
•
•
•
Diagnostics
Supported Standards: AT&T TR 62411,
AT&T TR 54016, ANSI T1.403,
Bellcore TR 194
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB (long)
or 0 to 655 feet (short)
Connector: RJ-48C
DS0 Assignment: Programmable
•
•
•
Compliance
•
•
•
•
•
•
•
•
•
•
Physical
•
ACTA/FCC Part 68, IC CS-03
UL/CUL 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Environmental
Clock Source
Network
Internal
Test Pattern Generation and Detection: 511,
QRSS, all ones, all zeros
Network loopbacks (local and remote);
responds to both inband and FDL loop
codes
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to 70°C
(-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
19
Option Modules
ProCurve Secure Router Installation Guide
1xT1 + DSX-1 Interface Module
The 1xT1 + DSX-1 Interface Module (see Figure 6) provides a full T1 or fractional T1 network interface and
a DSX-1 interface. Refer to Table A-3 on page 44 for the T1 connector pinouts, Table A-5 on page 44 for the
DSX-1 connector pinouts, and Table A-12 on page 47 for the backup connector pinouts. An optional backup
module is required for backup applications.
Figure 6. 1xT1 + DSX-1 Interface Module
Features and Specifications
Operating Modes
•
•
•
T1/FT1 Frame Relay/Multilink Frame Relay
T1/FT1 PPP/Multilink PPP
T1/FT1 HDLC
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411,
AT&T TR 54016, Bellcore TR 194,
ANSI T1.403
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized (multiples
of 56/64 kbps)
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB (long)
or 0 to 655 feet (short)
Connector: RJ-48C
DS0 Assignment: Programmable
DSX-1 Interface
•
•
•
•
•
•
•
•
•
•
•
•
Line Interface: DSX-1 per ANSI T1.102
DSX Receiver Input Range: -10 dBdsx to +6
dBdsx
Line Rate: 1.544 Mbps
Capacity: 1 to 24 DS0s
Line Codes: AMI, B8ZS
Framing: D4 (SF) or ESF
Line Length: 0 to 655 feet and -7.5 dB
Connector: RJ-48C
DSX-1 interface to PBX
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Diagnostics
•
•
•
•
Test Pattern Generation and Detection: 511,
QRSS, all ones, all zeros
Network loopbacks (local and remote);
responds to both inband and FDL loop
codes (T1 interface only)
Alarm generation and detection
Network and user sets of performance data
(15 minutes and 24 hours)
Compliance
•
•
•
ACTA/FCC Part 68, IC CS-03
UL/CUL 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Environmental
•
•
•
•
•
20
Network
Internal
Through
Physical
•
T1/FT1 Interface
•
Clock Source
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to 70°C
(-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
2xT1 Interface Module
The 2xT1 Interface Module (see Figure 7) provides two T1 interfaces for the ProCurve Secure Router. The
module provides up to 1.544 Mbps on each network interface. Refer to Table A-3 on page 44 for the
pinouts. Refer to Table A-12 on page 47 for the backup connector pinouts. An optional backup module is
required for backup applications.
Figure 7. 2xT1 Interface Module
Features and Specifications
Diagnostics
Operating Modes
•
•
•
•
•
T1/ FT1 Frame Relay/Multilink Frame Relay
T1/FT1 PPP/Multilink PPP
T1/FT1 HDLC
T1 Interface
•
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411,
AT&T TR 54016, Bellcore TR 194,
ANSI T1.403
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 channelized
Input Signal: 0 to -36 dB (DS1)
Line Build-Out: 0, -7.5, -15, -22.5 dB
Connector: RJ-48C
DS0 Assignment: Programmable
•
•
Compliance
•
•
•
•
•
•
•
•
•
•
Physical
•
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Note
5990-3760
ACTA/FCC Part 68, IC CS-03
UL/CUL 60950, IEC 60950
EMC - refer to Electromagnetic
Compatibility (EMC) Table on page 62.
Environmental
Clock Source
Network
Internal
Through
Test Pattern Generation and Detection:
QRSS, 511, 215-1, 220-1, all ones, all zeros
Network loopbacks (local and remote);
responds to both inband and FDL loop codes
(T1 interface only)
Alarm generation and detection
Network performance data (15 minutes and
24 hours)
•
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to 70°C
(-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
The 2xT1 module supports a single clock source for both T1 interfaces. Changing the
clock source on one T1 interface automatically affects the configuration of the other T1
interface. For example, setting the clock to line on the first T1 configures the clock source
of the second T1 as through.
Copyright 2006 Hewlett-Packard Development Company, LP
21
Option Modules
ProCurve Secure Router Installation Guide
1xE1 Interface Module
The 1xE1 Interface Module (see Figure 8) provides an E1 interface for the ProCurve Secure Router meeting
the requirements of ITU-T G.703/G.704. The module provides a single 2.048 Mbps network interface. Refer
to Table A-4 on page 44 for the pinouts. Refer to Table A-12 on page 47 for the backup connector pinouts.
An optional backup module is required for backup applications.
Figure 8. 1xE1 Interface Module
Features and Specifications
Operating Modes
Compliance
•
•
•
•
•
•
E1/ FE1 Frame Relay/Multilink Frame Relay
E1/FE1 PPP/Multilink PPP
E1/FE1 HDLC
E1 Interface
•
•
•
•
•
•
•
Supported Standards: ITU-T G.703,
ITU-T G.704 (CRC-4), ITU-T G.797,
ITU-T G.823
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized timeslot
(in multiples of 56/64 kbps)
Receiver Sensitivity: -30 dB
Connector: RJ-48C
ACIF S016, ETSI TBR 12/TBR 13
EN 60950, IEC 60950, AS/NZS 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to 70°C
(-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Clock Source
Physical
•
•
•
Network
Internal
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Diagnostics
•
•
•
•
22
Test Pattern Generation and Detection: QRSS,
511, all ones, all zeros
Network loopbacks
Alarm generation and detection
Network performance data (15 minutes and
24 hours)
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
1xE1 + G.703 Drop and Insert Interface Module
The 1xE1 + G.703 Drop and Insert Interface Module (see Figure 9) provides a single E1 interface
(2.043 Mbps) with user-selectable TS0 assignment and a G.703 drop port which may be used to drop and
insert traffic to an E1 PBX. Refer to Table A-4 on page 44 for the E1 pinouts. Refer to Table A-6 on page 45
for the G.703 pinouts. Refer to Table A-12 on page 47 for the backup connector pinouts. An optional backup
module is required for backup applications.
Figure 9. 1xE1 + G.703 Drop and Insert Interface Module
Features and Specifications
Operating Modes
Diagnostics
•
•
•
•
E1/ FE1 Frame Relay/Multilink Frame Relay
E1/FE1 PPP/Multilink PPP
E1/FE1 HDLC
E1 Interface
•
•
•
•
•
•
•
Supported Standards: ITU-T G.703,
ITU-T G.704 (CRC-4), ITU-T G.797,
ITU-T G.823
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized timeslot
(in multiples of 56/64 kbps)
Receiver Sensitivity: -30 dB
Connector: RJ-48C
G.703 Interface
•
•
•
•
•
•
•
Line Interface: Per ITU-T G.703
Line Rate: 2.048 Mbps ± 50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
Capacity: 1 to 31 timeslots
Receiver Sensitivity: -30 dB
Connector: RJ-48C
Clock Source
•
•
•
Network
Internal
Through
5990-3760
•
•
•
Test Pattern Generation and Detection:
QRSS, 511, all ones, all zeros
Network loopbacks
Alarm generation and detection
Network performance data (15 minutes and
24 hours)
Compliance
•
•
•
ACIF S016, ETSI TBR 12/TBR 13
EN 60950, AS/NZS 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Environmental
•
•
•
•
•
Operating temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Copyright 2006 Hewlett-Packard Development Company, LP
23
Option Modules
ProCurve Secure Router Installation Guide
2xE1 Interface Module
The 2xE1 Interface Module (see Figure 10) provides two E1 interfaces for the ProCurve Secure Router
meeting the requirements of ITU-T G.703/G.704. The module provides up to 2.048 Mbps on each network
interface. Refer to Table A-4 on page 44 for the pinouts. Refer to Table A-12 on page 47 for the backup
connector pinouts. An optional backup module is required for backup applications.
Figure 10. 2xE1 Interface Module
Features and Specifications
Operating Modes
Clock Source
•
•
•
Compliance
E1/FE1 Frame Relay/Multilink Frame Relay
E1/FE1 PPP/Multilink PPP
E1/FE1 HDLS
E1 Interface
•
•
•
•
•
•
•
Supported Standards: ITU-T G.703,
ITU-T G.704 (CRC-4), ITU-T G.797,
ITU-T G.823
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS with optional CRC-4
FE1 Line Rate: Channelized timeslot
(in multiples of 56/64 kbps)
Receiver Sensitivity: -30 dB
Connector: RJ-48C
Diagnostics
•
•
•
•
Note
24
Test Pattern Generation and Detection: QRSS,
215 - 1, all ones, all zeros
Network loopbacks
Alarm generation and detection
Network performance data (15 minutes and
24 hours)
•
•
•
•
Network, internal, and through
ACIF S016, ETSI TBR 12/TBR 13
EN 60950, IEC 60950, AS/NZS 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to 70°C
(-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
The 2xE1 module supports a single clock source for both E1 interfaces. Changing the
clock source on one E1 interface automatically affects the configuration of the other E1
interface. For example, setting the clock to line on the first E1 configures the clock source
of the second E1 as through.
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
1xSerial Interface Module
The 1xSerial Interface Module (see Figure 11) is user-configurable to be either a V.35 or an X.21 (V.11)
interface. This module supports rates up to a maximum of 10 Mbps. An additional V.35 or X.21 cable is
required (see Note, below). Refer to Table A-7 on page 45 for the Serial connector pinouts, and to Table A-12
on page 47 for the backup connector pinouts. An optional backup module is required for backup applications.
Caution
Cable length for the Serial Interface Module should not exceed 25 feet.
Note
Cables for the Serial module must be ordered separately: V.35 DTE (J8757A) or
X.21 DTE (J8755A).
Figure 11. 1xSerial Interface Module
Features and Specifications
Operating Mode
Compliance
•
•
•
•
•
Frame Relay/Multilink Frame Relay
PPP/Multilink PPP
HDLC
•
Serial Interface
•
•
•
•
DTE only; no internal clock provided
Supported Standards: ISO 4903 (X.21)
CCITT V.35 Synchronous (V.35)
Provides V.35 or X.21 (V.11) electrical
interface
26-pin smart serial (DTE) connector
•
•
V.35 DTE (J8757A)
X.21 DTE (J8755A)
•
•
•
•
Physical
•
Environmental
•
Optional Cables
ETSI TBR 1, ETSI TBR 2
EN 60950, UL/CUL 60950,
AS/NZS 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Operating Temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
25
Option Modules
ProCurve Secure Router Installation Guide
1xADSL2+ Annex A Interface Module
The 1xADSL2+ Annex A Interface Module (see Figure 12) adds ADSL capability to the ProCurve Secure
Router. Performance information is provided below. Refer to Table A-8 on page 46 for the pinouts. Refer
to Table A-12 on page 47 for the backup connector pinouts. An optional backup module is required for
backup applications.
Figure 12. 1xADSL2+ Annex A Interface Module
Features and Specifications
ADSL Interface
ADSL1 Performance
•
•
•
•
ADSL over POTS, Annex A
Supported Standards:
– ITU G.992.1 – Annex A (G.dmt)
– ITU G.992.2 – Annex A (G.lite)
– ITU G.992.3 – Annex A ADSL2
(G.dmt.bis)
– ITU G.992.3 – Annex L READSL2
– ITU G.992.5 – Annex A ADSL2+
– ANSI T1.413 Issue 2
Connector: RJ-11 (6-pin jack, inner pair)
Multiple Protocol over AAL5 (RFC2684)
ATM Forum UNI 3.1/4.0 PVC
Up to 16 Virtual Circuits
ATM Class of Service (UBR)
PPP over ATM (RFC2364)
PPP over Ethernet (RFC2516)
ATM F5 OAM
Compliance
•
•
•
ADSL2 Performance
•
•
Max = ~12 Mbps downstream and
~1 Mbps upstream
Min = 224 kbps downstream and
32 kbps upstream
ADSL2+ Performance*
ATM
•
•
•
•
•
•
•
•
Max = 8 Mbps downstream and
800 kbps upstream
Min = 224 kbps downstream and
32 kbps upstream
ACTA/FCC Part 68, IC CS-03,
AS/ASIF S043, AS/ACIF S002
EN 60950, IEC 60950, UL/CUL 60950,
AS/NZS 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
•
Max = ~24.5 Mbps downstream and up to 2
Mbps upstream
• Min = 224 kbps downstream and 32 kbps
upstream
*ADSL2+ support is planned in a future software update.
Environmental
•
•
•
•
•
Operating temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
26
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
1xADSL2+ Annex B Interface Module
The 1xADSL2+ Annex B Interface Module (see Figure 13) adds ADSL capability to the ProCurve Secure
Router. Performance information is provided below. Refer to Table A-9 on page 46 for the pinouts. Refer
to Table A-12 on page 47 for the backup connector pinouts. An optional backup module is required for
backup applications.
Figure 13. 1xADSL2+ Annex B Interface Module
Features and Specifications
ADSL1 Performance
ADSL Interface
•
•
•
•
•
ADSL over ISDN, Annex B
Supported Standards:
– ITU G.992.1 – Annex B (G.dmt)
RJ-11C (6-pin jack, inner pair)
•
•
•
•
•
•
•
Multiple Protocol over AAL5 (RFC2684)
ATM Forum UNI 3.1/4.0 PVC
Up to 16 Virtual Circuits
ATM Class of Service (UBR)
PPP over ATM (RFC2364)
PPP over Ethernet (RFC2516)
ATM F5 OAM
Compliance
•
•
EN 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Physical
•
ADSL2 Performance
•
ATM
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
•
Max = ~12 Mbps downstream and
~1 Mbps upstream
Min = 224 kbps downstream and
32 kbps upstream
ADSL2+ Performance*
•
•
Max = ~24.5 Mbps downstream and up to
2 Mbps upstream
Min = 224 kbps downstream and 32 kbps
upstream
*ADSL2+ support is planned in a future software update.
Environmental
•
•
•
•
•
5990-3760
Max = 8 Mbps downstream and
800 kbps upstream
Min = 224 kbps downstream and
32 kbps upstream
Operating temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Copyright 2006 Hewlett-Packard Development Company, LP
27
Option Modules
ProCurve Secure Router Installation Guide
2xISDN BRI S/T Interface Module
The 2xISDN BRI S/T Interface Module (see Figure 14) adds BRI ISDN (with S/T interface) capability to
the ProCurve Secure Router. Refer to Table A-10 on page 46 for the pinouts. Refer to Table A-12 on page
47 for the backup connector pinouts. An optional backup module is required for backup applications.
Figure 14. 2xISDN BRI S/T Interface Module
Features and Specifications
•
Operating Mode
•
Independent TE mode of operation for each
interface
•
•
Line Rate: Network support for 128 kbps
(2 B channels per interface)
Switch Compatibility: Euro-ISDN
Test Capability: Local and network
loopbacks
•
•
•
Compliance
•
•
28
EN 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Environmental
•
Features
•
Physical
•
Operating temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
2xISDN BRI U Interface Module
The 2xISDN BRI U Interface Module (see Figure 15) adds ISDN BRI (with U interface) capability to the
ProCurve Secure Router. Refer to Table A-11 on page 46 for the pinouts. Refer to Table A-12 on page 47
for the backup connector pinouts. An optional backup module is required for backup applications.
Figure 15. 2xISDN BRI U Interface Module
Features and Specifications
•
Operating Mode
•
Independent TE mode of operation for each
interface
•
•
Line Rate: Network support for 128 kbps
(2 B channels per interface)
Switch Compatibility: Euro-ISDN
Test Capability: Local and network
loopbacks
•
•
•
Compliance
•
•
EN 60950, IEC 60950
EMC - see Electromagnetic Compatibility
(EMC) Table on page 62
5990-3760
Dimensions: 6.99 cm (2.75 in) W x
10.80 cm (4.25 in) D
Environmental
•
Features
•
Physical
•
Operating temperature: 0°C to 50°C (32°F
to 122°F)
Non-Operating Temperature: -20°C to
70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent
noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to
95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Copyright 2006 Hewlett-Packard Development Company, LP
29
Option Modules
ProCurve Secure Router Installation Guide
8xT1/E1 Wide Module
The 8xT1/E1 Wide Module (see Figure 16) provides eight T1/E1 WAN interfaces. Refer to Table A-3 on
page 44 for the T1 interface pinouts. Refer to Table A-4 on page 44 for the E1 interface pinouts.
Figure 16. 8xT1/E1 Wide Module
Features and Specifications
Operating Modes
•
•
•
•
•
•
Note
T1/FT1 Frame Relay/Multilink Frame Relay
T1/FT1 PPP/Multilink PPP
T1/FT1 HDLC
E1/FE1 Frame Relay/Multilink Frame Relay
E1/FE1 PPP/Multilink PPP
E1/FE1 HDLC
A dip-switch on the circuit board selects either T1 or E1 operation. All 8 ports are either
T1 or E1. The default is T1. See T1/E1 Mode Dip-Switch on page 40 for more
information.
8xT1 Interfaces
•
•
•
•
•
•
•
•
Supported Standards: AT&T TR 62411, AT&T TR 54016, ANSI T1.403, Bellcore TR 194
Line Rate: 1.544 Mbps +75 bps
Line Code: AMI or B8ZS
Framing: D4 (SF) or ESF
FT1 Line Rate: DS0 Channelized
Input Signal: 0 to -36 dB (DS1); Support for Nx64 on all T1 interfaces
Line Build-Out: 0, -7.5, -15, -22.5 dB
Connector: RJ-48C
8xE1 Interfaces
•
•
•
•
•
•
•
Supported Standards: ITU-T G.703, ITU-T G.704 (CRC-4), ITU-T G.823, ITU-T G.797
Line Rate: 2.048 Mbps +50 PPM
Line Code: AMI or HDB3
Framing: FAS/NFAS with optional CRC-4
FE1 Line Rate: Channelized timeslot
Input Signal: 0 to -30 dB (DS1) on all E1 interfaces (1 through 8)
Connector: RJ-48C
Clock Source
•
30
Network, internal
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
Diagnostics
•
•
Network Loopbacks: Line, payload, remote
Test Pattern Generation and Detection: QRSS, 215 - 1, 511, all ones, all zeros
Compliance
•
•
•
ACIF S016, ETSI TBR 12/TBR 13, ACTA/FCC Part 68, IC CS-03
UL/CUL 60950, EN 60950, IEC 60950, AS/NZS 60950
EMC - see Electromagnetic Compatibility (EMC) Table on page 62.
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Relative Humidity: 95 percent noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: 95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
14.29 cm (5.63 in) W x 21.91 cm (8.63 in) D
Note
5990-3760
No external CSU/DSU is needed with the T1/FT1 or E1/FE1 interface.
Copyright 2006 Hewlett-Packard Development Company, LP
31
Option Modules
ProCurve Secure Router Installation Guide
8xSerial Wide Module
The 8xSerial Wide Module (see Figure 17) provides eight serial interfaces. Refer to Table A-7 on page 45 for
the serial interface pinouts.
Note
Cable length for the 8xSerial Wide Module should not exceed 25 feet.
Note
Cables for the 8xSerial Wide Module must be ordered separately: V.35 DTE (J8757A) or
X.21 (V.11) DTE (J8755A).
Figure 17. 8xSerial Wide Module
Features and Specifications
Operating Modes
•
•
•
Frame Relay/Multilink Frame Relay
PPP/Multilink PPP
HDLC
8xSerial Interfaces
•
•
•
•
•
DTE operation only; no internal clock provided
Clocking up to 10 Mbps for each interface
Supported Standards: ISO 4903 (X.21), CCITT V.35 Synchronous (V.35)
Provides eight V.35 of X.21 (V.11) electrical interfaces; additional adapter cables are available for
purchase to provide the V.35 DTE (J8757A) and X.21 DTE (J8755A) interfaces
Connector: 25-pin smart serial (DTE) connector
Compliance
•
•
ETSI TBR 1, ETSI TBR 2
EN 60950, UL/CUL 60950, AS/NZS 60950, IEC 60950
EMC - see Electromagnetic Compatibility (EMC) Table on page 62.
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Relative Humidity: 95 percent noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: 95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
32
14.29 cm (5.63 in) W x 21.91 cm (8.63 in) D
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
Backup Modules
ISDN BRI U Backup Module
The ISDN BRI U Backup Module provides backup access to the public switched telephone network
(PSTN) via Basic Rate ISDN for the ProCurve Secure Router. This backup module is a plug-on module
that connects to the interface module. For installation instructions, see Installing Interface and Backup
Modules on page 38. Refer to Table A-12 on page 47 for backup connector pinouts.
Features and Specifications
Features
•
•
•
•
Clear Channel and Bonding Mode 1 call protocols
Network support for 64 kbps (1 B-channel)
D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, and
National ISDN-1
V.54 network loopback support
Compliance
•
•
ACTA/FCC Part 68, IC CS-03, UL/CUL 60950
EMC - see Electromagnetic Compatibility (EMC) Table on page 62
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
Dimensions: 6.35 cm (2.5 in) W x 9.53 cm (3.75 in) D
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
33
Option Modules
ProCurve Secure Router Installation Guide
ISDN S/T Backup Module
The ISDN S/T Backup Module provides backup access to the public switched telephone network (PSTN)
via Basic Rate ISDN for the ProCurve Secure Router. This backup module is a plug-on module that
connects to the interface module. For installation instructions, see Installing Interface and Backup Modules
on page 38. Refer to Table A-13 on page 47 for backup connector pinouts.
Features and Specifications
Features
•
•
•
•
Clear Channel and Bonding Mode 1 call protocols
Network support for 64 kbps (1 B-channel)
D-channel switch compatibility with AT&T 5ESS, Northern Telecom DMS-100, National ISDN-1,
and Euro-ISDN
V.54 network loopback support
Compliance
•
•
•
ACIF S031, ETSI TBR 3
AS/NZS 60950, EN 60950
EMC - see Electromagnetic Compatibility (EMC) Table on page 62
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
34
Dimensions: 6.35 cm (2.5 in) W x 9.53 cm (3.75 in) D
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Option Modules
Analog Modem Backup Module
The Analog Modem Backup Module provides a modem with data rates up to 33.6 kbps for the ProCurve
Secure Router. This backup module is a plug-on card that connects to the interface module. For installation
instructions, see Installing Interface and Backup Modules on page 38. Refer to Table A-12 on page 47 for
backup connector pinouts.
Features and Specifications
Features
•
•
ITU V.90 compliant
Async
Compliance
•
•
•
ETSI TBR 21, IC CS-03, ACTA/FCC Part 68
UL/CUL 60950, AS/NZS 60950, IEC 60950, EN 60950
EMC - see Electromagnetic Compatibility (EMC) Table on page 62
Environmental
•
•
•
•
•
Operating Temperature: 0°C to 50°C (32°F to 122°F)
Non-Operating Temperature: -20°C to 70°C (-4°F to 158°F)
Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Non-Operating Relative Humidity: Up to 95 percent noncondensing at 30°C (86°F)
Altitude: Up to 3.05 km (10,000 ft)
Physical
•
Dimensions: 6.35 cm (2.5 in) W x 9.53 cm (3.75 in) D
Note
The Analog Modem Backup Module can be used in two different modes:
1. Backup interface for a primary connection.
2. Console port for remote dial-in access.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
35
Unit Installation
4.
ProCurve Secure Router Installation Guide
UNIT INSTALLATION
The instructions and guidelines provided in this section cover hardware installation topics such as rack
mounting the unit and installing option cards. These instructions are presented as follows:
•
•
•
•
Mounting Options on page 37
Grounding Requirements Statement on page 38
Installing Interface and Backup Modules on page 38
Installing the Encryption Module on page 40
•
•
•
•
Installing a CompactFlash® Card on page 40
T1/E1 Mode Dip-Switch on page 40
Supplying Power to the Unit on page 41
Supplying Redundant Power to the Unit on page 41
For information on router configuration for a specific application, refer to the quick configuration
documents provided on your ProCurve SROS Documentation CD. For details on the command line
interface, refer to the SROS Command Line Interface Reference Guide (also included on your CD).
To prevent electrical shock, do not install equipment in a wet location or during an
electrical storm.
Warning
Caution
Electronic modules can be damaged by static electrical discharge. Before handling
modules, wear an antistatic discharge wrist strap to prevent damage to electrical
components. Place modules in antistatic packing material when transporting or storing.
When working with modules, always place them on an approved antistatic mat that is
electrically grounded.
Tools Required
The following customer-provided tools are required for the hardware installation of the ProCurve Secure
Router:
•
•
•
•
•
•
Ethernet cable
Network cable (module dependent)
DSX-1 cable (1xT1 + DSX-1 module only)
G.703 cable (1xE1 + G.703 module only)
Backup cable (backup functions require an optional backup module)
Flat-blade or Torx T-10 screwdriver
Note
36
To access the command line interface (CLI) of the ProCurve Secure Router, you will also
need a VT100 terminal or PC with terminal emulation software and a CONSOLE port
cable. Instructions on how to access the CLI are given in the Quick Start Guide shipped
with your router and in the SROS Command Line Interface Reference Guide (provided
on the ProCurve SROS Documentation CD).
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Unit Installation
Mounting Options
The ProCurve Secure Router may be installed in a tabletop or 19-inch rackmount configuration. The
following section provides step-by-step instructions for rack mounting.
Rack Mounting ProCurve Secure Router
The ProCurve Secure Router is housed in a 1U-high, rack-mountable chassis which can be installed in
19-inch equipment racks. Follow these steps to mount the ProCurve Secure Router in a rack:
Instructions for Rack Mounting the ProCurve Secure Router
1
Position the ProCurve Secure Router in a stationary equipment rack. This unit occupies 1U of
space. To allow proper grounding, scrape the paint from the rack around the mounting holes
where the ProCurve Secure Router will be positioned. See the section Grounding the Router.
2
Using the rack mounting hardware supplied with your router, have an assistant hold the unit in
position as you install two mounting bolts through the unit’s brackets and into the equipment
rack.
3
Proceed to the steps given in Grounding the Router (below) and in Supplying Power to the Unit
on page 41.
Caution
Be careful not to compromise the stability of the equipment mounting rack when installing
this product.
Grounding the Router
Note
The supplemental equipment grounding terminal is located on the rear panel of the
ProCurve Secure Router.
Follow these steps to ground the ProCurve Secure Router:
Instructions for Grounding the ProCurve Secure Router
1
Strip one end of the ground wire to the length required for the ring terminal. (Ground wire and
ring terminal are supplied by the user.)
2
Crimp the ground wire to the ring terminal, using a crimp tool of the appropriate size.
3
Attach the ring terminal to the chassis as shown in Figure 18 on page 38. A 6/32 x 1/4 inch
screw and a washer are provided next to the AC inlet receptacle for connection to a reliable
ground.
4
Connect the other end of the ground wire to a suitable grounding point at your site.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
37
Unit Installation
ProCurve Secure Router Installation Guide
Figure 18. Grounding the ProCurve Secure Router
Grounding Requirements Statement
A supplementary equipment grounding conductor shall be installed between the product or system and
ground that is in addition to the equipment grounding conductor in the power supply cord. The supplementary
equipment grounding conductor shall not be smaller in size than the ungrounded branch-circuit supply
conductors. The supplementary equipment grounding conductor shall be connected to the product at the
terminal provided, and shall be connected to ground in a manner that will retain the ground connection when
the product is unplugged from the receptacle. The connection to ground of the supplementary equipment
grounding conductor shall be in compliance with the rules for terminating bonding jumpers at Part K or
Article 250 of the National Electrical Code, ANSI/NFPA 70. Termination of the supplementary equipment
grounding conductor is permitted to be made to building steel, to a metal electrical raceway system, or to any
grounded item that is permanently and reliably connected to the electrical service equipment ground.
The supplemental grounding conductor shall be connected to the equipment using a number 8 ring terminal and
should be fastened to the grounding terminal provided on the rear panel of the equipment. The ring terminal
should be installed using the appropriate crimping tool (AMP P/N 59250 T-EAD crimping tool or equivalent).
Installing Interface and Backup Modules
The backup modules plug on to the interface modules. The interface modules are then installed in the front
panel option module slot. The following tables list the installation steps. See Figure 19 on page 39.
Caution
Always remove power from the unit prior to removing or installing a module.
Improper installation may result in damage to the modules.
Warning
38
For ProCurve Secure Router modules with outside plant connections, ensure that all
cables are removed from the module before installing or removing it from the router
chassis.
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Unit Installation
Instructions for Installing the Backup Module
Remove power from the unit.
2
If the interface module is already installed in the ProCurve Secure Router chassis, remove all
connected cables, release the screws at both edges of the interface module front panel, and
slide the module out of the chassis.
3
Carefully align the P1 connector on the interface module with the J1 connector on the backup
module. Using only fingertip pressure so that neither circuit board bends or flexes, ensure that
the connectors are firmly seated. Secure the backup module to the interface module using the
screws and standoff posts supplied. (See Figure 19.)
4
Slide the interface module with the backup module attached into the ProCurve Secure Router
chassis, continuing with the normal interface module installation.
IC: 2250A-J8462
ITE
P/N: J8462A
32F8
US: PNBMM04AJ8462
1
2
Eth 0/2
1
Eth 0/1
3
IC: 2250A-J8462
ITE
32F8
P/N: J8462A
US: PNBMM04AJ8462
dl
Figure 19. Installing Backup Module and Interface Module
Instructions for Installing the Interface Modules and Wide Modules
1
Remove power from the unit.
2
Slide the option module into the option slot until the module is firmly seated against the chassis.
(See Figure 19.)
3
Secure the screws at both edges of the module.
4
Connect the cables to the associated device(s).
5
Restore power to the unit.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
39
Unit Installation
ProCurve Secure Router Installation Guide
Installing the Encryption Module
The Encryption Module slot supports the 7100/7200 IPSec Module. All software options associated with the
card become available once the card is installed. Follow these cautions and steps when installing a module.
Caution
Always remove power from the unit prior to removing or installing a module.
Improper installation may result in damage to the modules.
Instructions for Installing the Encryption Module
1
Remove power from the unit.
2
Remove the blank cover plate from the Encryption Module slot.
3
Slide the module into the Encryption Module slot until the module is firmly seated against the
chassis.
4
Secure the screws at both edges of the module.
5
Restore power to the unit.
6
The configuration options for encryption will now be available in the GUI and the SROS CLI.
Installing a CompactFlash® Card
The Compact Flash slot supports any Type 1 CompactFlash® card (16 MB to 1 GB). Follow these
instructions when installing the card.
Note
The CompactFlash® card is hot-swappable and can be inserted or removed while power is
applied to the unit.
Instructions for Installing a CompactFlash® Card
1
Slide the module into the Compact Flash slot until the card is firmly seated against the
chassis.
2
The CompactFlash® options will now be available in the GUI and the SROS CLI.
T1/E1 Mode Dip-Switch
The ProCurve Secure Router dl 8x T1/E1 Wide Module is shipped with the T1/E1 mode switch (located on
the circuit board) set to T1 (in the 1 position). If you require E1 functionality, use your thumbnail to slide
the switch to the ON position (as shown in the figure below).
Switch Set to T1 Mode
Switch Set to E1 Mode
40
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Unit Installation
Supplying Power to the Unit
After installing the base unit and any option modules, the ProCurve Secure Router is ready to be poweredup. To power the unit, ensure that the unit is properly connected to an appropriate power source (see the
sections below).
The ProCurve Secure Router comes equipped with an auto-ranging power supply rated as follows:
•
•
ProCurve Secure Router 7102dl: 100 to 127 VAC, 0.4 A/200 to 240 VAC, 0.2 A, 50 to 60 Hz
ProCurve Secure Router 7203dl: 100 to 127 VAC, 0.8 A/200 to 240 VAC, 0.4 A, 50 to 60 Hz
A grounded, three-plug detachable cable is included with the shipment.
Caution
Maximum recommended ambient operating temperature is 50°C (122°F).
Supplying Redundant Power to the Unit
A redundant power supply (RPS) is only available with the ProCurve Secure Router 7203dl. Follow these
instructions when connecting the RPS.
Instructions for Connecting the RPS
1
Remove the blank cover plate from the RPS slot on the back of the ProCurve Secure Router 7203dl.
2
Plug the RPS power cable (with the HP logo on the connector facing up) into this slot. (The RPS
power cable comes attached to the HP 600 RPS/EPS. The cable is 1.25 meters [4.1 feet] long.)
For more information about connecting the RPS, refer to the ProCurve 600 Redundant and External
Power Supply Installation and Getting Started Guide.
3
Secure the screws.
Your ProCurve Secure Router is now ready to be configured and connected to the network. For more
information on configuring a specific application, refer to the quick configuration documents provided on
your ProCurve SROS Documentation CD. For details on the CLI, refer to the SROS Command Line
Interface Reference Guide (also included on your CD).
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
41
Unit Installation
42
ProCurve Secure Router Installation Guide
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
APPENDIX A. CONNECTOR PIN DEFINITIONS
The following tables provide the pin assignments for the base unit, interface modules, and backup
modules.
Base Unit Pinouts
Table A-1. CONSOLE Port (DTE) Pinouts
Pin
Name
1
—
Unused
2
RD
Receive Data (input)
3
TD
Transmit Data (output)
4
DTR
Data Terminal Ready (output)
5
SG
Signal Ground
6
DSR
Data Set Ready (input)
7
RTS
Request to Send (output)
8
CTS
Clear to Send
9
—
Note
Description
Unused
Direct connection to an external modem requires a straight-through cable.
Table A-2. 10/100BaseT Ethernet Port Pinouts
Pin
Name
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4, 5
—
6
RX2
7, 8
—
5990-3760
Description
Unused
Receive Negative
Unused
Copyright 2006 Hewlett-Packard Development Company, LP
43
Appendix A. Connector Pin Definitions
ProCurve Secure Router Installation Guide
Interface Module and Wide Module Pinouts
Table A-3. T1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network
2
T1
Receive data from the network
3
—
Unused
4
R
Transmit data toward the network
5
T
Transmit data toward the network
6-8
—
Unused
Table A-4. E1 Connector Pinouts
Pin
Name
Description
1
R1
Receive data from the network
2
T1
Receive data from the network
3
—
Unused
4
R
Transmit data toward the network
5
T
Transmit data toward the network
6-8
—
Unused
Table A-5. DSX-1 Connector Pinouts
44
Pin
Name
Description
1
R
Transmit data toward the DTE
2
T
Transmit data toward the DTE
3
—
Unused
4
R1
Receive data from the DTE
5
T1
Receive data from the DTE
6-8
—
Unused
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix A. Connector Pin Definitions
Table A-6. G.703 Connector Pinouts
Pin
Name
Description
1
R
Transmit data toward the DTE
2
T
Transmit data toward the DTE
3
—
Unused
4
R1
Receive data from the DTE
5
T1
Receive data from the DTE
6-8
—
Unused
Table A-7. 1xSerial Interface and 8xSerial Wide Module Connector Pinouts
Serial Pin
V.35 Pin
X.21 Pin
1
P
2
2
U
N/A
External transmit clock (ETC_A)
3
Y
N/A
Transmit clock A (TCLK_A)
4
V
6
Receive clock A (RCLK_A)
5
R
4
Receive data A (RD_A)
6
F
N/A
Data carrier detect A (DCD_A)
7
H
N/A
Data transmit ready A (DTR_A)
8
C
3
Request to send A (RTS_A)
9
N/A
10
Request to send B (RTS_B)
V.11 only
10
N/A
12
Clear to send B (CTS_B)
V.11 only
11
D
5
Clear to send A (CTS_A)
12
E
N/A
Data set ready A (DSR_A)
13
K
N/A
Test mode A (TM_A)
14
S
9
15
W
N/A
External transmit clock B (ETC_B)
16
AA
N/A
Transmit clock B (TCLK_B)
17
X
13
Receive clock B (RCLK_B)
18
T
11
Receive data B (RD_B)
19-25
N/A
N/A
26
B
8
5990-3760
Description
Transmit data A (TD_A)
Transmit data B (TD_B)
Unused
Ground (GND)
Copyright 2006 Hewlett-Packard Development Company, LP
45
Appendix A. Connector Pin Definitions
ProCurve Secure Router Installation Guide
Table A-8. 1xADSL2+ Annex A Interface Module Connector Pinouts
Pin
Name
Description
1, 2
—
Unused
3
R
ADSL Ring
4
T
ADSL Tip
5, 6
—
Unused
Table A-9. 1xADSL2+ Annex B Interface Module Connector Pinouts
Pin
Name
Description
1, 2
—
Unused
3
R
ADSL Ring
4
T
ADSL Tip
5, 6
—
Unused
Table A-10. 2xISDN BRI S/T Interface Module Connector Pinouts
Pin
Name
Description
1, 2
—
Unused
3
R1
Network – Receive (Ring 1)
4
R
Network – Transmit (Ring)
5
T
Network – Transmit (Tip)
6
T1
Network – Receive (Tip 1)
7, 8
—
Unused
Table A-11. 2xISDN BRI U Interface Module Connector Pinouts
46
Pin
Name
Description
1-3
—
Unused
4
R
Network – Ring
5
T
Network – Tip
6-8
—
Unused
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix A. Connector Pin Definitions
Backup Connectors
Table A-12 describes the backup connector pinouts for the Analog Modem Backup Module and the
ISDN BRI U Backup Module.
Note
An optional backup module is required for backup applications.
Table A-12. Analog Modem and ISDN BRI U Backup Modules Connector Pinouts
Pin
Name
Description
1-3
—
Unused
4
R
Network – Ring
5
T
Network – Tip
6-8
—
Unused
Table A-13 describes the backup connector pinouts for the ISDN BRI S/T Backup Module.
Table A-13. ISDN BRI S/T Backup Module Connector Pinouts
Pin
Name
Description
1, 2
—
Unused
3
R
Network – Receive
4
T
Network – Transmit
5
T
Network – Transmit
6
R
Network – Receive
7, 8
—
Unused
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
47
Appendix A. Connector Pin Definitions
48
ProCurve Secure Router Installation Guide
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
APPENDIX B. SAFETY AND REGULATORY INFORMATION
ESD Precautions
Static electricity can severely damage the electronic components on the modules. When handling and
installing the modules in your switch, follow these procedures to avoid damage from static electricity:
1. Handle the module by its bulkhead or edges and avoid touching the components and the circuitry
on the board.
2. When installing the module, equalize any static charge difference between your body and the
router by wearing a grounding wrist strap and attaching it to the router’s metal body, or by
frequently touching the router’s metal body.
Safety Information (English)
Note
Notes provide important information.
Caution
Cautions appear before procedures which, if not observed, could result in loss of data or
damage to equipment.
Warning
Warning messages alert the reader to a specific procedure or practice which, if not
followed correctly, could cause personal injury or catastrophic loss of data or equipment.
Do not proceed beyond a WARNING or CAUTION notice until you have understood the hazardous
conditions and have taken appropriate steps.
Safety Instructions
When using this equipment, please follow these basic safety precautions to reduce the risk of fire, electrical
shock, or personal injury:
1. Do not use this product near water, such as a wash bowl, sink, or in a wet basement.
2. Avoid touching this product during an electrical storm. There is a remote risk of shock from
lightning.
3. Use only the power cord indicated in the manual.
4. The socket-outlet shall be installed near the equipment and shall be easily accessible.
Warning
5990-3760
Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
Copyright 2006 Hewlett-Packard Development Company, LP
49
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Grounding
This product is a Safety Class I compliant product and has a protective earthing terminal. There must be an
uninterruptible safety earth ground from the main power source to the product's power cord or supplied
power cord set. Whenever it is likely that the protection has been impaired, disconnect the power cord until
the ground has been restored.
For LAN cable grounding:
• If your LAN covers an area served by more than one power distribution system, be sure their safety
grounds are securely interconnected.
• LAN cables may occasionally be subject to hazardous transient voltages (such as lightning or
disturbances in the electrical utilities power grid). Handle exposed metal components of the network
with caution.
Servicing
There are no user-serviceable parts inside this product. Any servicing, adjustment, maintenance, or repair
must be performed only by service trained personnel.
This product does not have a power switch; it is powered on when the power cord is plugged in to an AC
power source.
Accessories
Regulatory information for accessories can be found in the installation instructions included with them.
Regulatory Model Identification Number
For regulatory identification purposes, this product has been assigned a Regulatory Model Number
(RMN). The RMN for your product is RSVLC-0407. The RMN should not be confused with the marketing
name (ProCurve Secure Router) or the Product Number (J8752A or J8753A).
50
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Conserver ces instructions de sécurité
Tout changement ou modification de cet appareil non approuve par l'entité responsable de la conformité
engage l'entière responsabilité de l'utilisateur sur les risques encourus.
Informations concernant la sécurité (French)
Symbole de référence à la documentation. Si le produit est marqué de ce symbole, reportez-vous à la
documentation du produit afin d'obtenir des informations plus détaillées.
Warning
Indique un danger susceptible d'entraîner des dommages corporels ou la mort.
Caution
Indique un danger susceptible de causer des dommages à l'équipement.
Note
Indique des informations plus détaillées.
Instruction de sécurité
Durant l'utilisation de cet équipement, suivre les consignes de sécurité élémentaires afin de minimiser le
risque d'incendie, d'électrocution ou de blessures infligées aux personnes:
1. N'utilisez pas le produit à proximité de l'eau, par exemple, près d'un bac de lavage, d'un évier ou
dans un sous-sol humide.
2. Evitez de toucher ce produit durant un orage. Il peut y avoir un risque de choc électrique cause par
l'orage.
3. Utilisez seulement le cordon d'alimentation spécifie dans le manuel.
4. Placez l'équipement près d'une prise électrique facilement accessible.
Mise à la terre
Cet appareil est un produit de classe I et possède une borne de mise à la terre. La source d'alimentation
principale doit être munie d'une prise de terre de sécurité installée aux bornes du câblage d'entrée, sur le
cordon d'alimentation ou le cordon de raccordement fourni avec le produit.
Lorsque cette protection semble avoir été endommagée, débrancher le cordon d'alimentation jusqu'à ce que
la mise à la terre ait été réparée.
Mise à la terre du câble de réseau local (LAN):
• Si votre LAN s'étend sur une zone desservie par plus d'un système de distribution de puissance, assurezvous que les prises de terre de sécurité soient convenablement interconnectées.
• Les câbles LAN peuvent occasionnellement être soumis à des surtensions transitoires dangereuses (telles
que la foudre ou des perturbations dans le réseau d'alimentation public). Manipulez les composants
métalliques du réseau avec précautions.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
51
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Reparation
Aucune pièce contenue à l'intérieur de ce produit ne peut être réparée par l'utilisateur. Tout dépannage,
réglage, entretien ou réparation devra être confié exclusivement à un personnel qualifié. Cet appareil ne
comporte pas de commutateur principal ; la mise sous tension est effectuée par branchement du cordon
d'alimentation.
Accessoires
Les informations réglementaires des accessoires sont fournies avec les instructions d'installation des
accessoires.
Numéro de modèle réglementaire:
Un numéro de modèle réglementaire HP (RMN: Regulatory Model Number) est affecte au produit a des
fins d'identification et de certificat de conformité aux diverses réglementations. Le modèle réglementaire
HP de ce produit est RSVLC-0407.
Ne confondez pas le numéro de modèle réglementaire (RMN) avec l'appellation commerciale (HP
Procurve Secure Router) ou avec la reference ou numéro de produit (J8752A ou J8753A).
52
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Hinweise zur Sicherheit (German)
Symbol für Dokumentationsverweis. Wenn das Produkt mit diesem Symbol markiert ist, schlagen Sie bitte
in der Produktdokumentation nach, um mehr Informationen über das Produkt zu erhalten.
Warning
Das Wort WARNING in der Dokumentation symbolisiert eine Gefahr, die Verletzungen
oder sogar Todesfälle verursachen kann.
Caution
Das Wort CAUTION in der Dokumentation symbolisiert eine Gefahr, die das Gerät
beschädigen kann.
Anweisungen zur Sicherheit
Folgen Sie bei der Benutzung des Gerätes bitte den grundsätzlichen Sicherheitsvorkehrungen um Gefahren
durch Feuer, elektrischem Schlag oder persönlichem Verletzungen zu vermeiden:
1. Benutzen Sie dieses Produkt nicht in der Nähe von Wasser, wie z.B. Wasch- und Spülbecken oder
in feuchten Kellern.
2. Vermeiden Sie das Berühren des Produktes während eines Gewitters. Es besteht die Gefahr eines
elektrischen Schlages während eines Blitzeinschlages.
3. Benutzen Sie nur das im Handbuch angegebene Netzkabel.
4. Die Netzsteckdose soll leicht zugänglich und nahe beim Gerät angebracht sein.
Erdung des Gerätes
Dies ist ein Gerät der Sicherheitsklasse I und verfügt über einen schützenden Erdungsanschluss. Der
sichere Betrieb des Geräts erfordert eine ununterbrochene Verbindung der Schutzerde von der
Hauptstromquelle zum Netzkabel und zum Geräteanschluss. Sobald Grund zur Annahme besteht, daß der
Schutz beeinträchtigt ist, das Netzkabel aus der Wandsteckdose herausziehen und erst wieder
zurückstecken, wenn die Erdungsverbindung wiederhergestellt ist.
Für LAN-Kabelerdung:
• Wenn Ihr LAN ein Gebiet umfasst, das von mehr als einem Stromverteilungssystem beliefert wird,
müssen Sie sich vergewissern, dass die Sicherheitserdungen fest untereinander verbunden sind.
• LAN-Kabel können gelegentlich gefährlichen Übergangsspannungen ausgesetzt sein (beispielsweise
durch Blitz oder Störungen in dem Starkstromnetz des Elektrizitätswerks). Bei der Handhabung
exponierter Metallbestandteile des Netzwerkes Vorsicht walten lassen.
Wartungsarbeiten
Dieses Gerät enthält keine durch den Benutzer zu wartenden Teile. Wartungs-, Anpassungs-,
Instandhaltungs- -oder Reparaturarbeiten dürfen nur von geschultem Bedienungspersonal durchgeführt
werden.
Dieses Gerät hat keinen Netzschalter; es wird beim Anschließen des Netzkabels eingeschaltet.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
53
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Produktidentifizierung durch “Regulatory Model Number"
Zur Identifizierung dieses Produktes wurde eine eindeutige Nummer, die sogenannte Regulatory Model
Number (RMN) vergeben. Die RMN für dieses Produkt ist: RSVLC-0407
Die RMN ist unabhängig vom Produktname (HP ProCurve Secure Router) und von der Produkt-nummer
(J8752A oder J8753A) und wird zu regulatorischen Zwecken benutzt.
54
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Conservare queste importanti istruzioni sulla sicurezza
Cambiamenti o modifiche a questa unità non espessamente approvata dalla parte responsabile per la
conformità può invalidare l'autorità dell'utente ad operare con l'apparecchio
Informationi sulla sicurezza (Italian)
Se il prodotto è contrassegnato da questo simbolo, si raccomanda di fare riferimento alla documentazione
del prodotto per ulteriori informazioni.
I seguenti simboli sono usati nella documentazione del prodotto:
Warning
Indica un pericolo che può causare lesioni o morte.
Caution
Indica un pericolo che può danneggiare le attrezzature.
Note
Indica informazioni più dettagliate.
Instruzioni di sicurezza
Nell'operare con questa apparecchiatura, si prega di seguire le seguenti misure di sicurezza di base per
ridurre il rischio di scossa elettrica, di incendio, o di ferita personale:
1. Non usare questo prodotto vicino ad acqua od oggetti che contengono acqua, quale un contenitore
per pulizie, un lavandino, o in uno scantinato bagnato.
2. Astenersi dal toccare questo prodotto durante un temporale o una tempesta elettrica. C'è un rischio
sebbene limitato di scossa elettrica dovuto ai fulmini e le cariche elettrostatiche.
3. Usare solo i cavi di alimentazione indicati nel manuale.
4. Assicurarsi che la presa di corrente sia facilmente acessibile e sia installata nelle vicinanze del
prodotto.
Messa a terra
Questo prodotto è omologato alla classe di sicurezza "I" ed ha un terminale protettivo di collegamento a
terra. Dev'essere installato con un collegamento a terra di sicurezza, non interrompibile che vada dalla
fonte d'alimentazione principale ai terminali d'entrata, al cavo d'alimentazione oppure al set
d'alimentazione fornito con il prodotto. Ogniqualvolta vi sia un possibile danneggiamento della protezione,
disinserite il cavo d'alimentazione fino a quando il collegaento a terra non sia stato ripristinato.
Per la messa a terra dei cavi LAN:
• se la vostra LAN copre un'area servita da più di un sistema di distribuzione elettrica, accertatevi che i
collegamenti a terra di sicurezza siano ben collegati fra loro;
• i cavi LAN possono occasionalmente essere soggetti a pericolose tensioni transitorie (ad esempio,
provocate da lampi o disturbi nella griglia d'alimentazione della società elettrica); siate cauti nel toccare
parti esposte in metallo della rete.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
55
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Assistenza
Nessun componente di questo prodotto può essere riparato dall'utente. Qualsiasi lavoro di riparazione,
messa a punto, manutenzione o assistenza va effettuato esclusivamente da personale specializzato.
Questo apparato non possiede un commutatore principale; questo prodotto si mette sotto tensione
all'inserimento del cavo d'alimentazione.
Accessori
Ulteriori informationi per gli accessori sono disponibili nelle istruzioni di installazione con essi distribuite.
Regulatory Model Identification Number
Un numero di modello regolamentario (Regulatory Model Number o RMN) è stato assegnato a questo
prodotto per identificare il prodotto da un punto di vista di coniformità alle norme, le regolamentazioni e
legislazioni tecniche.
Il RMN per questo prodotto è RSVLC-0407. Il numero di modello regolamentario non deve essere confuso
con il nome di commercializzazione del prodotto (ProCurve Secure Router) o il numero del modello del
prodotto (J8752A or J8753A).
56
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Conservar estas Instrucciones de seguridad Importantes
Cambios o modificaciones a esta unidad no claramente afirmada por el partido responsable de
conformidad implica la entera responsabilidad del usuario sobre los riesgos incurridos.
Consideraciones sobre la seguridad (Spanish)
Si el producto está marcado de este símbolo, consultar la documentación del producto a fin de obtener
mayor información sobre el producto.
Los símbolos siguientes se utilizan en la documentación del producto:
Warning
Señala un riesgo que podría resultar en lesiones o la muerte.
Caution
Señala un riesgo que podría resultar en averías al equipo.
Note
Señala información adicional útil.
Instrucciones de seguridad
Al usar este equipo, siga por favor estas medidas de seguridad básicas para reducir el riesgo del fuego, del
choque eléctrico, o de los daños corporales:
1. No utilice este producto cerca del agua.
2. Evite de tocar este producto durante una tormenta eléctrica. Hay un riesgo alejado del choque del
relámpago.
3. Utilice solamente el cable eléctrico indicado en el manual.
4. El zócalo-enchufe debe ser fácilmente accesible y se debe instalar cerca del equipo.
Puesta a tierra
Este aparato se enmarca dentro de la clase I de seguridad y se encuentra protegido por una borna de puesta
a tierra. Es preciso que exista una puesta a tierra continua desde la toma de alimentación eléctrica hasta las
bornas de los cables de entrada del aparato, el cable de alimentación o el juego de cable de alimentación
suministrado. Si existe la probabilidad de que la protección a tierra haya sufrido desperfectos, desenchufar
el cable de alimentación hasta haberse subsanado el problema.
Puesta a tierra del cable de la red local (LAN):
• Si la LAN abarca un área cuyo suministro eléctrico proviene de más de una red de distribución de
electricidad, cerciorarse de que las puestas a tierra estén conectadas entre sí de modo seguro.
• Es posible que los cables de la LAN se vean sometidos de vez en cuando a voltajes momentáneos que
entrañen peligro (rayos o alteraciones en la red de energía eléctrica). Manejar con precaución los
componentes de metal de la LAN que estén al descubierto.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
57
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Mantenimiento
Este aparato no contiene pieza alguna susceptible de reparación por parte del usuario. Todas las
reparaciones, ajustes o servicio de mantenimiento debe realizarlos solamente el técnico.
Este producto no tiene interruptor de potencia; se activa cuando se enchufa el cable de alimentación.
Accesorios
La información reguladora para los accesorios se puede encontrar en las instrucciones de instalación
incluidas con ellas.
Regulatory Model Identification Number
Para los propósitos reguladores de la identificación, este producto se ha asignado un Regulatory Model
Number (RMN).
El RMN para su producto es: RSVLC-0407. El RMN no se debe confundir con el nombre de la
comercialización (ProCurve Secure Router) o el número del modelo del producto (J8752A o J8753A).
58
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Safety Information (Japan)
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
59
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Safety Information (China)
60
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
FCC Radio Frequency Interference Statement for United States
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference, in which case the user will be required to
correct the interference at his own expense. The end user of this product should be aware that any changes
or modifications made to this equipment without the approval of Hewlett-Packard could result in the
product not meeting the Class A limits, in which case the FCC could void the user's authority to operate the
equipment.
Hewlett-Packard's device certification tests were conducted with HP computer systems and HP shielded
cables, such as those you received with your product. Changes or modifications not expressly approved by
Hewlett-Packard could void the user's authority to operate the equipment. Cables used with this device
must be properly shielded to comply with the requirements of the FCC.
For information on electromagnetic compatibility, see the Electromagnetic Compatibility (EMC) Table on
page 62.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
61
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Electromagnetic Compatibility (EMC) Table
Module Part Number
Module Name
J8451A
1xT1 Interface
J8452A
1xT1 + DSX-1 Interface
J8453A
J8454A
J8456A
2xT1 Interface
1xE1 Interface
2xE1 Interface
J8455A
1xE1 + G.703 Interface
J8457A
2xISDN BRI S/T Interface
J8458A
1xSerial Interface
J8459A
1xADSL2+ Annex A
Interface
J8759A
1xADSL2+ Annex B
Interface
J8460A
J8461A
ISDN BRI U Backup
ISDN BRI S/T Backup
J8462A
Analog Modem Backup
J8463A
8xT1/E1 Wide
J8471A
7100/7200 IPSec
62
ProCurve Secure Router
FCC Part 15, Class A
EN 55022 Class A
FCC Part 15, Class A
EN 55022 Class A
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 61000-3-2
EN61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Module Part Number
Module Name
J9010A
2xISDN BRI U Interface
J9011A
8xSerial Wide
5990-3760
Appendix B. Safety and Regulatory Information
ProCurve Secure Router
FCC Part 15, Class A
EN 55022 Class A
EN 61000-3-2
EN 61000-3-3
FCC Part 15, Class A
EN 55022 Class A
EN 55024
EN 61000-3-2
EN 61000-3-3
Copyright 2006 Hewlett-Packard Development Company, LP
63
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Industry Canada Compliance Information
Notice: The Industry Canada label applied to the product (identified by the Industry Canada logo or the
“IC:” in front of the certification/registration number) signifies that the Industry Canada technical
specifications were met.
Notice: The Ringer Equivalence Number (REN) for this terminal equipment is supplied in the
documentation or on the product labeling/markings. The REN assigned to each terminal device indicates
the maximum number of terminals that can be connected to a telephone interface. The termination on an
interface may consist of any combination of devices subject only to the requirement that the sum of the
RENs of all the devices should not exceed five (5).
Canadian Emissions Requirements
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus
as set out in the interference-causing equipment standard entitled “Digital Apparatus,” ICES-003 of the
Department of Communications.
Cet appareil numérique respecte les limites de bruits radioelectriques applicables aux appareils numériques
de Class A prescrites dans la norme sur le materiel brouilleur: “Appareils Numériques,” NMB-003 edictee
par le ministre des Communications.
Notice for European Union
This is a Class A product. In a domestic environment this product may cause radio interference, in which
case the user may be required to take adequate measures. This product has been tested in accordance to,
and complies with, the Low Voltage Directive (73/23/EEC) and EMC Directive (89/336/EEC). The
product has been marked with the CE Mark to illustrate its compliance.
Notice for France
DECLARATION D'INSTALLATION ET DE MISE EN EXPLOITATION d'un matériel de traitement de
l'information (ATI), classé A en fonction des niveaux de perturbations radioélectriques émis, définis dans
la norme européenne EN 55022 concernant la Compatibilité Electromagnétique.
64
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Notice for Japan
EMC
Harmonics
Japanese Power Cord
Notice for Korea
Notice for Germany
Geraeuschemission LwA=60 dB am fiktiven Arbeitsplatz nach DIN 45635 T.19 and
ISO 7779:1999
Noise Emission LwA=60 dB at virtual workspace according to DIN 45635 T.19 and
ISO 7779:1999
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
65
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
FCC-Required Information
FCC regulations require that the following information be provided in this manual:
1. This equipment complies with Part 68 of FCC rules and requirements adopted by ACTA. Each
registered interface has a label that contains, among other information, a product identifier in the
format US:AAAEQ##TXXXX. If requested, provide this information to the telephone company.
2. If this equipment causes harm to the telephone network, the telephone company may temporarily
discontinue service. If possible, advance notification is given; otherwise, notification is given as
soon as possible. The telephone company will advise the customer of the right to file a complaint
with the FCC.
3. The telephone company may make changes in its facilities, equipment, operations, or procedures
that could effect the proper operation of this equipment. Advance notification and the opportunity
to maintain uninterrupted service are given.
4. If experiencing difficulty with this equipment, please contact Hewlett-Packard for repair and
warranty information. The telephone company may require this equipment to be disconnected
from the network until the problem is corrected or it is certain the equipment is not
malfunctioning.
5. This unit contains no user-serviceable parts.
6. This equipment is designed to connect to the telephone network or premises wiring using an
FCC-compatible modular jack, which is compliant with Part 68 and requirements adopted by
ACTA.
7. The following information may be required when applying to the local telephone company for
leased line facilities:
Product
Part Number
1xT1 Interface Module
J8451A
1xT1 + DSX-1 Interface Module
J8452A
2xT1 Interface Module
J8453A
8xT1/E1 Wide Module
J8463A
Service Type
REN/SOC
FIC
USOC
6.0N
04DU9-BN
04DU9-DN
04DU9-1KN
04DU9-1SN
RJ-48C
1.544 Mbps - SF
1.544 Mbps - SF and B8ZS
1.544 Mbps - ESF
1.544 Mbps - ESF and B8ZS
Analog Modem Backup Module
J8462A
Analog Loop Start
0.4A/9.0Y
02LS2
RJ-11C
ISDN BRI U Backup Module
J8460A
Basic Rate ISDN
6.0N
02IS5
RJ-49C
2xISDN BRI U Interface Module
J9010A
Basic Rate ISDN
6.0N
02IS5
RJ-49C
1xADSL2+ Annex A Interface Module
J8459A
ADSL, ADSL2, ADSL2+
0.1A
Metallic
RJ-11C
8. The REN is useful in determining the quantity of devices you may connect to your telephone line
and still have all of those devices ring when your number is called. In most areas, the sum of the
RENs of all devices should not exceed five. To be certain of the number of devices you may
connect to your line as determined by the REN, call your telephone company to determine the
maximum REN for your calling area.
9. This equipment may not be used on coin service provided by the telephone company. Connection
to party lines is subject to state tariffs. Contact your state public utility commission or corporation
commission for information.
66
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Declaration of Conformity (USA)
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
67
Appendix B. Safety and Regulatory Information
ProCurve Secure Router Installation Guide
Declaration of Conformity (European)
68
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix B. Safety and Regulatory Information
Warranty and Customer Service
Warranty and Support information for your product is found in the Software License, Warranty, and
Support documentation that ships in the product box. An electronic copy of this document may be found
on the Documentation CD included with the product or on the ProCurve Web site at
http://www.procurve.com. Click on Technical Support, then, under Additional Support, click on Warranty
information and assistance.
Installation and Maintenance Support
ProCurve Networking and HP Services provide a range of service and support options to assist you in the
installation and maintenance of your network. For more information, visit http://hp.com/go/
procurveservices.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
69
Appendix B. Safety and Regulatory Information
70
ProCurve Secure Router Installation Guide
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
APPENDIX C. WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT
(WEEE) INSTRUCTIONS
Likvidace zařízení soukromými domácími uživateli v Evropské unii
Tento symbol na produktu nebo balení označuje výrobek, který nesmí být vyhozen
spolu s ostatním domácím odpadem. Povinností uživatele je předat takto označený
odpad na předem určené sběrné místo pro recyklaci elektrických a elektronických
zařízení. Okamžité třídění a recyklace odpadu pomůže uchovat přírodní prostředí
a zajistí takový způsob recyklace, který ochrání zdraví a životní prostředí člověka. Další
informace o možnostech odevzdání odpadu k recyklaci získáte na příslušném obecním
nebo městském úřadě, od firmy zabývající se sběrem a svozem odpadu nebo v
obchodě, kde jste produkt zakoupili.
Bortskaffelse af affald fra husstande i den Europæiske Union
Hvis produktet eller dets emballage er forsynet med dette symbol, angiver det, at
produktet ikke må bortskaffes med andet almindeligt husholdningsaffald. I stedet er det
dit ansvar at bortskaffe kasseret udstyr ved at aflevere det på den kommunale
genbrugsstation, der forestår genvinding af kasseret elektrisk og elektronisk udstyr. Den
centrale modtagelse og genvinding af kasseret udstyr i forbindelse med bortskaffelsen
bidrager til bevarelse af naturlige ressourcer og sikrer, at udstyret genvindes på en måde,
der beskytter både mennesker og miljø. Yderligere oplysninger om, hvor du kan aflevere
kasseret udstyr til genvinding, kan du få hos kommunen, den lokale genbrugsstation eller
i den butik, hvor du købte produktet.
Disposal of Waste Equipment by Users in Private Household in the European Union
This symbol on the product or on its packaging indicates that this product must not be
disposed of with your other household waste. Instead, it is your responsibility to dispose
of your waste equipment by handing it over to a designated collection point for the
recycling of waste electrical and electronic equipment. The separate collection and
recycling of your waste equipment at the time of disposal will help to conserve natural
resources and ensure that it is recycled in a manner that protects human health and the
environment. For more information about where you can drop off your waste equipment
for recycling, please contact your local city office, your household waste disposal service
or the shop where you purchased the product.
Seadmete jäätmete kõrvaldamine eramajapidamistes Euroopa Liidus
See tootel või selle pakendil olev sümbol näitab, et kõnealust toodet ei tohi koos teiste
majapidamisjäätmetega kõrvaldada. Teie kohus on oma seadmete jäätmed kõrvaldada,
viies need elektri- ja elektroonikaseadmete jäätmete ringlussevõtmiseks selleks
ettenähtud kogumispunkti. Seadmete jäätmete eraldi kogumine ja ringlussevõtmine
kõrvaldamise ajal aitab kaitsta loodusvarasid ning tagada, et ringlussevõtmine toimub
viisil, mis kaitseb inimeste tervist ning keskkonda. Lisateabe saamiseks selle kohta,
kuhu oma seadmete jäätmed ringlussevõtmiseks viia, võtke palun ühendust oma
kohaliku linnakantselei, majapidamisjäätmete kõrvaldamise teenistuse või kauplusega,
kust Te toote ostsite.
Laitteiden hävittäminen kotitalouksissa Euroopan unionin alueella
Jos tuotteessa tai sen pakkauksessa on tämä merkki, tuotetta ei saa hävittää
kotitalousjätteiden mukana. Tällöin hävitettävä laite on toimitettava sähkölaitteiden ja
elektronisten laitteiden kierrätyspisteeseen. Hävitettävien laitteiden erillinen käsittely
ja kierrätys auttavat säästämään luonnonvaroja ja varmistamaan, että laite kierrätetään
tavalla, joka estää terveyshaitat ja suojelee luontoa. Lisätietoja paikoista, joihin
hävitettävät laitteet voi toimittaa kierrätettäväksi, saa ottamalla yhteyttä jätehuoltoon tai
liikkeeseen, josta tuote on ostettu.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
71
Appendix C. WEEE Instructions
ProCurve Secure Router Installation Guide
Élimination des appareils mis au rebut par les ménages dans l'Union européenne
Le symbole apposé sur ce produit ou sur son emballage indique que ce produit ne doit
pas être jeté avec les déchets ménagers ordinaires. Il est de votre responsabilité de
mettre au rebut vos appareils en les déposant dans les centres de collecte publique
désignés pour le recyclage des équipements électriques et électroniques. La collecte
et le recyclage de vos appareils mis au rebut indépendamment du reste des déchets
contribue à la préservation des ressources naturelles et garantit que ces appareils seront
recyclés dans le respect de la santé humaine et de l'environnement. Pour obtenir plus
d'informations sur les centres de collecte et de recyclage des appareils mis au rebut,
veuillez contacter les autorités locales de votre région, les services de collecte des
ordures ménagères ou le magasin dans lequel vous avez acheté ce produit.
Entsorgung von Altgeräten aus privaten Haushalten in der EU
Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass das Produkt
nicht über den normalen Hausmüll entsorgt werden darf. Benutzer sind verpflichtet, die
Altgeräte an einer Rücknahmestelle für Elektro- und Elektronik-Altgeräte abzugeben.
Die getrennte Sammlung und ordnungsgemäße Entsorgung Ihrer Altgeräte trägt zur
Erhaltung der natürlichen Ressourcen bei und garantiert eine Wiederverwertung, die die
Gesundheit des Menschen und die Umwelt schützt. Informationen dazu, wo Sie
Rücknahmestellen für Ihre Altgeräte finden, erhalten Sie bei Ihrer Stadtverwaltung, den
örtlichen Müllentsorgungsbetrieben oder im Geschäft, in dem Sie das Gerät erworben
haben
Απόρριψη άχρηστου εξοπλισµού από χρήστες σε ιδιωτικά νοικοκυριά
στην Ευρωπαϊκή Ένωση
Το σύµβολο αυτό στο προϊόν ή τη συσκευασία του υποδεικνύει ότι το
συγκεκριµένο προϊόν δεν πρέπει να διατίθεται µαζί µε τα άλλα οικιακά σας
απορρίµµατα. Αντίθετα, είναι δική σας ευθύνη να απορρίψετε τον άχρηστο
εξοπλισµό σας παραδίδοντάς τον σε καθορισµένο σηµείο συλλογής για την
ανακύκλωση άχρηστου ηλεκτρικού και ηλεκτρονικού εξοπλισµού. Η ξεχωριστή
συλλογή και ανακύκλωση του άχρηστου εξοπλισµού σας κατά την απόρριψη θα
συµβάλει στη διατήρηση των φυσικών πόρων και θα διασφαλίσει ότι
η ανακύκλωση γίνεται µε τρόπο που προστατεύει την ανθρώπινη υγεία και το
περιβάλλον. Για περισσότερες πληροφορίες σχετικά µε το πού µπορείτε να
παραδώσετε τον άχρηστο εξοπλισµό σας για ανακύκλωση, επικοινωνήστε µε το
αρµόδιο τοπικό γραφείο, την τοπική υπηρεσία διάθεσης οικιακών απορριµµάτων
ή το κατάστηµα όπου αγοράσατε το προϊόν.
Készülékek magánháztartásban történő selejtezése az Európai Unió területén
A készüléken, illetve a készülék csomagolásán látható azonos szimbólum annak
jelzésére szolgál, hogy a készülék a selejtezés során az egyéb háztartási hulladéktól
eltérő módon kezelendő. A vásárló a hulladékká vált készüléket köteles a kijelölt
gyűjtőhelyre szállítani az elektromos és elektronikai készülékek újrahasznosítása
céljából. A hulladékká vált készülékek selejtezéskori begyűjtése és újrahasznosítása
hozzájárul a természeti erőforrások megőrzéséhez, valamint biztosítja a selejtezett
termékek környezetre és emberi egészségre nézve biztonságos feldolgozását.
A begyűjtés pontos helyéről bővebb tájékoztatást a lakhelye szerint illetékes
önkormányzattól, az illetékes szemételtakarító vállalattól, illetve a terméket elárusító
helyen kaphat.
Smaltimento delle apparecchiature da parte di privati nel territorio dell'Unione Europea
Questo simbolo presente sul prodotto o sulla sua confezione indica che il prodotto non
può essere smaltito insieme ai rifiuti domestici. È responsabilità dell'utente smaltire le
apparecchiature consegnandole presso un punto di raccolta designato al riciclo e allo
smaltimento di apparecchiature elettriche ed elettroniche. La raccolta differenziata e il
corretto riciclo delle apparecchiature da smaltire permette di proteggere la salute degli
individui e l'ecosistema. Per ulteriori informazioni relative ai punti di raccolta delle
apparecchiature, contattare l'ente locale per lo smaltimento dei rifiuti, oppure il negozio
presso il quale è stato acquistato il prodotto.
72
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Appendix C. WEEE Instructions
Nolietotu iekārtu iznīcināšanas noteikumi lietotājiem Eiropas Savienības
privātajās mājsaimniecībās
Šāds simbols uz izstrādājuma vai uz tā iesaiņojuma norāda, ka šo izstrādājumu
nedrīkst izmest kopā ar citiem sadzīves atkritumiem. Jūs atbildat par to, lai nolietotās
iekārtas tiktu nodotas speciāli iekārtotos punktos, kas paredzēti izmantoto elektrisko
un elektronisko iekārtu savākšanai otrreizējai pārstrādei. Atsevišķa nolietoto iekārtu
savākšana un otrreizējā pārstrāde palīdzēs saglabāt dabas resursus un garantēs, ka
šīs iekārtas tiks otrreizēji pārstrādātas tādā veidā, lai pasargātu vidi un cilvēku
veselību. Lai uzzinātu, kur nolietotās iekārtas var izmest otrreizējai pārstrādei,
jāvēršas savas dzīves vietas pašvaldībā, sadzīves atkritumu savākšanas dienestā vai
veikalā, kurā izstrādājums tika nopirkts.
Vartotojų iš privačių namų ūkių įrangos atliekų šalinimas Europos Sąjungoje
Šis simbolis ant gaminio arba jo pakuotės rodo, kad šio gaminio šalinti kartu su
kitomis namų ūkio atliekomis negalima. Šalintinas įrangos atliekas privalote
pristatyti į specialią surinkimo vietą elektros ir elektroninės įrangos atliekoms
perdirbti. Atskirai surenkamos ir perdirbamos šalintinos įrangos atliekos padės
saugoti gamtinius išteklius ir užtikrinti, kad jos bus perdirbtos tokiu būdu, kuris
nekenkia žmonių sveikatai ir aplinkai. Jeigu norite sužinoti daugiau apie tai, kur
galima pristatyti perdirbtinas įrangos atliekas, kreipkitės į savo seniūniją, namų ūkio
atliekų šalinimo tarnybą arba parduotuvę, kurioje įsigijote gaminį.
Verwijdering van afgedankte apparatuur door privé-gebruikers in de Europese Unie
Dit symbool op het product of de verpakking geeft aan dat dit product niet mag worden
gedeponeerd bij het normale huishoudelijke afval. U bent zelf verantwoordelijk voor het
inleveren van uw afgedankte apparatuur bij een inzamelingspunt voor het recyclen van
oude elektrische en elektronische apparatuur. Door uw oude apparatuur apart aan te
bieden en te recyclen, kunnen natuurlijke bronnen worden behouden en kan het
materiaal worden hergebruikt op een manier waarmee de volksgezondheid en het milieu
worden beschermd. Neem contact op met uw gemeente, het afvalinzamelingsbedrijf of
de winkel waar u het product hebt gekocht voor meer informatie over inzamelingspunten
waar u oude apparatuur kunt aanbieden voor recycling.
Pozbywanie się zużytego sprzętu przez użytkowników w prywatnych
gospodarstwach domowych w Unii Europejskiej
Ten symbol na produkcie lub jego opakowaniu oznacza, że produktu nie wolno
wyrzucać do zwykłych pojemników na śmieci. Obowiązkiem użytkownika jest
przekazanie zużytego sprzętu do wyznaczonego punktu zbiórki w celu recyklingu
odpadów powstałych ze sprzętu elektrycznego i elektronicznego. Osobna zbiórka oraz
recykling zużytego sprzętu pomogą w ochronie zasobów naturalnych i zapewnią
ponowne wprowadzenie go do obiegu w sposób chroniący zdrowie człowieka
i środowisko. Aby uzyskać więcej informacji o tym, gdzie można przekazać zużyty
sprzęt do recyklingu, należy się skontaktować z urzędem miasta, zakładem
gospodarki odpadami lub sklepem, w którym zakupiono produkt.
Descarte de Lixo Elétrico na Comunidade Européia
Este símbolo encontrado no produto ou na embalagem indica que o produto não deve ser
descartado no lixo doméstico comum. É responsabilidade do cliente descartar o material
usado (lixo elétrico), encaminhando-o para um ponto de coleta para reciclagem. A
coleta e a reciclagem seletivas desse tipo de lixo ajudarão a conservar as reservas
naturais; sendo assim, a reciclagem será feita de uma forma segura, protegendo o
ambiente e a saúde das pessoas. Para obter mais informações sobre locais que reciclam
esse tipo de material, entre em contato com o escritório da HP em sua cidade, com o
serviço de coleta de lixo ou com a loja em que o produto foi adquirido.
5990-3760
Copyright 2006 Hewlett-Packard Development Company, LP
73
Appendix C. WEEE Instructions
ProCurve Secure Router Installation Guide
Likvidácia vyradených zariadení v domácnostiach v Európskej únii
Symbol na výrobku alebo jeho balení označuje, že daný výrobok sa nesmie likvidovať s
domovým odpadom. Povinnosťou spotrebiteľa je odovzdať vyradené zariadenie v
zbernom mieste, ktoré je určené na recykláciu vyradených elektrických a
elektronických zariadení. Separovaný zber a recyklácia vyradených zariadení prispieva
k ochrane prírodných zdrojov a zabezpečuje, že recyklácia sa vykonáva spôsobom
chrániacim ľudské zdravie a životné prostredie. Informácie o zberných miestach na
recykláciu vyradených zariadení vám poskytne miestne zastupiteľstvo, spoločnosť
zabezpečujúca odvoz domového odpadu alebo obchod, v ktorom ste si výrobok
zakúpili.
Odstranjevanje odslužene opreme uporabnikov v zasebnih gospodinjstvih v
Evropski uniji
Ta znak na izdelku ali njegovi embalaži pomeni, da izdelka ne smete odvreči med
gospodinjske odpadke. Nasprotno, odsluženo opremo morate predati na zbirališče,
pooblaščeno za recikliranje odslužene električne in elektronske opreme. Ločeno
zbiranje in recikliranje odslužene opreme prispeva k ohranjanju naravnih virov in
zagotavlja recikliranje te opreme na zdravju in okolju neškodljiv način. Za podrobnejše
informacije o tem, kam lahko odpeljete odsluženo opremo na recikliranje, se obrnite na
pristojni organ, komunalno službo ali trgovino, kjer ste izdelek kupili.
Eliminación de residuos de equipos eléctricos y electrónicos por parte de usuarios
particulares en la Unión Europea
Este símbolo en el producto o en su envase indica que no debe eliminarse junto con los
desperdicios generales de la casa. Es responsabilidad del usuario eliminar los residuos
de este tipo depositándolos en un "punto limpio" para el reciclado de residuos eléctricos
y electrónicos. La recogida y el reciclado selectivos de los residuos de aparatos
eléctricos en el momento de su eliminación contribuirá a conservar los recursos
naturales y a garantizar el reciclado de estos residuos de forma que se proteja el medio
ambiente y la salud. Para obtener más información sobre los puntos de recogida de
residuos eléctricos y electrónicos para reciclado, póngase en contacto con su
ayuntamiento, con el servicio de eliminación de residuos domésticos o con el
establecimiento en el que adquirió el producto.
Bortskaffande av avfallsprodukter från användare i privathushåll inom Europeiska
Unionen
Om den här symbolen visas på produkten eller förpackningen betyder det att produkten
inte får slängas på samma ställe som hushållssopor. I stället är det ditt ansvar att
bortskaffa avfallet genom att överlämna det till ett uppsamlingsställe avsett för
återvinning av avfall från elektriska och elektroniska produkter. Separat insamling och
återvinning av avfallet hjälper till att spara på våra naturresurser och gör att avfallet
återvinns på ett sätt som skyddar människors hälsa och miljön. Kontakta ditt lokala
kommunkontor, din närmsta återvinningsstation för hushållsavfall eller affären där du
köpte produkten för att få mer information om var du kan lämna ditt avfall för återvinning.
74
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
Index
Index
Numerics
10/100BaseT Ethernet 10, 16
pinouts 43
1xADSL2+ (Annex A) interface module
features and specifications 26
pinouts 46
shipping contents 13
1xADSL2+ (Annex B) interface module
features and specifications 27
pinouts 46
shipping contents 13
1xE1 + G.703 interface module
features and specifications 23
pinouts
E1 44
G.703 45
shipping contents 12
1xE1 interface module
features and specifications 22
pinouts 44
shipping contents 12
1xSerial interface module
features and specifications 25
pinouts 45
shipping contents 13
1xT1 + DSX-1 interface module
features and specifications 20
pinouts
DSX-1 44
T1 44
shipping contents 12
1xT1 interface module
features and specifications 19
pinouts 44
shipping contents 11
2xE1 interface module
features and specifications 24
pinouts 44
shipping contents 12
2xISDN BRI S/T interface module
features and specifications 28
pinouts 46
shipping contents 12
2xISDN BRI U interface module
features and specifications 29
pinouts 46
shipping contents 12
2xT1 interface module
features and specifications 21
5990-3760
pinouts 44
shipping contents 12
7100/7200 IPSec Base Module 10, 17
shipping contents 14
7100/7200 IPSec Module 10, 17
shipping contents 14
8xSerial wide module
features and specifications 32
pinouts 45
shipping contents 14
8xT1/E1 wide module
dip-switch, T1/E1 mode 40
features and specifications 30, 32
pinouts
E1 44
T1 44
shipping contents 13
A
Activity LEDs 16
Analog Modem backup module
feature and specifications 35
pinouts 47
shipping contents 13
B
backup interface, pinouts 47
backup modules
Analog Modem backup module
features and specifications 35
pinouts 47
shipping contents 13
installation 38
ISDN BRI S/T backup module
features and specifications 34
pinouts 47
shipping contents 13
ISDN BRI U backup module
features and specifications 33
pinouts 47
shipping contents 13
C
command line interface 9
CompactFlash 17, 40
console port 16
pinouts 43
contents of shipment 11
Copyright 2006 Hewlett-Packard Development Company, LP
75
Index
ProCurve Secure Router Installation Guide
D
dimensions
ProCurve Secure Router 10
dip-switch, T1/E1 mode 40
DSX-1 interface, pinouts 44
E
E1 interface, pinouts 44
electrical specifications 11
encryption module 40
encryption module slot 17
environmental specifications
ESD precautions 49
11
F
fault LED 15
features of the ProCurve Secure Router
Frame Relay 10
front panel 15
10
G
G.703 interface, pinouts 45
grounding the router 37
I
installing CompactFlash card 40
installing encryption module 40
installing modules 38
installing the ProCurve Secure Router 36
interface modules 19
1xADSL2+ (Annex A) interface module
features and specifications 26
pinouts 46
shipping contents 13
1xADSL2+ (Annex B) interface module
features and specifications 27
pinouts 46
shipping contents 13
1xE1 + G.703 interface module
features and specifications 23
pinouts
E1 44
G.703 45
shipping contents 12
1xE1 interface module
features and specifications 22
pinouts 44
shipping contents 12
1xSerial interface module
features and specifications 25
pinouts 45
76
shipping contents 13
1xT1 + DSX-1 interface module
features and specifications 20
pinouts
DSX-1 44
shipping contents 12
1xT1 interface module
features and specifications 19
pinouts 44
shipping contents 11
2xE1 interface module
features and specifications 24
pinouts 44
shipping contents 12
2xISDN BRI S/T interface module
features and specifications 28
pinouts 46
shipping contents 12
2xISDN BRI U interface module
features and specifications 29
pinouts 46
shipping contents 12
2xT1 interface module
features and specifications 21
pinouts 44
shipping contents 12
8xSerial wide module
features and specifications 32
pinouts 45
shipping contents 14
8xT1/E1 wide module
dip-switch, T1/E1 mode 40
features and specifications 30,
pinouts
E1 44
T1 44
shipping contents 13
installation 38
ISDN BRI S/T backup module
features and specifications 34
pinouts 47
shipping contents 13
ISDN BRI U backup module
features and specifications 33
pinouts 47
shipping contents 13
L
LEDs, front panel
M
module card slot
32
15
16
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
ProCurve Secure Router Installation Guide
mounting options
37
N
non-operating temperature
O
operating temperature
option modules 18
grounding 37
installation 36
rear panel 17
shipping contents
specifications 10
11
11
P
pinouts
10/100BaseT Ethernet 43
ADSL (Annex A) 46
ADSL (Annex B) 46
backup 47
console port 43
DSX-1 44
E1 44
G.703 45
ISDN BRI S/T 46
ISDN BRI U 46
serial 45
T1 44
power 11, 41
redundant 17, 41
power LED 15
power supply 17
PPP 10
ProCurve Secure Router
dimensions 10
features 10
front panel 15
5990-3760
Index
11
R
rear panel 17
redundant power 17, 41
regulatory information 49
relative humidity 11
S
safety and regulatory information 49
safety information 49
serial interface, pinouts 45
software licensing agreement 4
specifications of the ProCurve Secure Router
10
T
T1 interface, pinouts 44
T1/E1 mode dip-switch 40
tools required for installation
trademarks 4
36
U
unit installation 36
unpack and inspect the system
W
warranty 4,
11
69
Copyright 2006 Hewlett-Packard Development Company, LP
77
Index
78
ProCurve Secure Router Installation Guide
Copyright 2006 Hewlett-Packard Development Company, LP
5990-3760
An intelligent tool for network contol
The information in this document
is subject to change without notice.
© Copyright 2006
Hewlett-Packard Development Company, L.P.
Reproduction, adaptation, or translation
without prior written permission is prohibited
except as allowed under the copyright laws.
May 2006
Manual Part Number
5990-8878
Printed in China
61195880L1-34E
Download PDF

advertising