HP C6Z78UT#ABA User's manual
HP Compaq Business PC Maintenance
and Service Guide
Pro 6300 Series Microtower
Pro 6300 Series Small Form Factor
© Copyright 2012 Hewlett-Packard
Development Company, L.P. The
information contained herein is subject to
change without notice.
Microsoft, Windows, and Windows Vista are
either trademarks or registered trademarks
of Microsoft Corporation in the United
States and/or other countries.
The only warranties for HP products and
services are set forth in the express
warranty statements accompanying such
products and services. Nothing herein
should be construed as constituting an
additional warranty. HP shall not be liable
for technical or editorial errors or omissions
contained herein.
This document contains proprietary
information that is protected by copyright.
No part of this document may be
photocopied, reproduced, or translated to
another language without the prior written
consent of Hewlett-Packard Company.
First Edition (June 2012)
Document Part Number: 690362-001
About This Book
WARNING! Text set off in this manner indicates that failure to follow directions could result in bodily
harm or loss of life.
CAUTION: Text set off in this manner indicates that failure to follow directions could result in
damage to equipment or loss of information.
NOTE:
Text set off in this manner provides important supplemental information.
iii
iv
About This Book
Table of contents
1 Product Features ............................................................................................................................................ 1
Standard Configuration Features ......................................................................................................... 1
Microtower (MT) Front Panel Components .......................................................................................... 2
Small Form Factor (SFF) Front Panel Components ............................................................................. 3
Microtower (MT) Rear Panel Components ........................................................................................... 4
Small Form Factor (SFF) Rear Panel Components ............................................................................. 5
Serial Number Location ........................................................................................................................ 6
2 Installing and Customizing the Software ...................................................................................................... 7
Installing the Windows Operating System ............................................................................................ 7
Downloading Microsoft Windows Updates ........................................................................................... 8
Installing or Upgrading Device Drivers (Windows systems) ................................................................. 8
Customizing the Monitor Display (Windows systems) .......................................................................... 8
Launching Windows XP from Windows 7 ............................................................................................. 9
Accessing Disk Image (ISO) Files ........................................................................................................ 9
3 Computer Setup (F10) Utility ....................................................................................................................... 10
Computer Setup (F10) Utilities ........................................................................................................... 10
Using Computer Setup (F10) Utilities ................................................................................ 11
Computer Setup—File ....................................................................................................... 12
Computer Setup—Storage ................................................................................................ 13
Computer Setup—Security ................................................................................................ 16
Computer Setup—Power ................................................................................................... 20
Computer Setup—Advanced ............................................................................................. 21
Recovering the Configuration Settings ............................................................................................... 23
4 Illustrated parts catalog ............................................................................................................................... 24
Microtower (MT) chassis spare parts ................................................................................................. 24
Computer major components ............................................................................................ 24
Cables ................................................................................................................................ 26
Misc parts .......................................................................................................................... 27
v
Drives ................................................................................................................................. 28
Misc boards ....................................................................................................................... 29
Sequential part number listing ........................................................................................... 29
Small Form Factor (SFF) chassis spare parts .................................................................................... 33
Computer major components ............................................................................................ 33
Cables ................................................................................................................................ 35
Misc parts .......................................................................................................................... 36
Drives ................................................................................................................................. 38
Misc boards ....................................................................................................................... 38
Sequential part number listing ........................................................................................... 39
5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation .................................................... 42
Electrostatic Discharge Information .................................................................................................... 42
Generating Static ............................................................................................................... 42
Preventing Electrostatic Damage to Equipment ................................................................ 43
Personal Grounding Methods and Equipment ................................................................... 43
Grounding the Work Area .................................................................................................. 44
Recommended Materials and Equipment .......................................................................... 44
Operating Guidelines .......................................................................................................................... 45
Routine Care ...................................................................................................................................... 45
General Cleaning Safety Precautions ................................................................................ 45
Cleaning the Computer Case ............................................................................................ 45
Cleaning the Keyboard ...................................................................................................... 46
Cleaning the Monitor .......................................................................................................... 46
Cleaning the Mouse ........................................................................................................... 47
Service Considerations ...................................................................................................................... 47
Power Supply Fan ............................................................................................................. 47
Tools and Software Requirements .................................................................................... 47
Screws ............................................................................................................................... 47
Cables and Connectors ..................................................................................................... 48
Hard Drives ........................................................................................................................ 48
Lithium Coin Cell Battery ................................................................................................... 48
SATA Hard Drives .............................................................................................................................. 49
SATA Hard Drive Cables .................................................................................................................... 49
SATA Data Cable .............................................................................................................. 49
SMART ATA Drives ............................................................................................................................ 49
Cable Management ............................................................................................................................ 49
Hard Drive Capacities ........................................................................................................................ 50
6 Removal and Replacement Procedures Microtower (MT) Chassis .......................................................... 51
Preparation for Disassembly .............................................................................................................. 51
vi
Computer Access Panel ..................................................................................................................... 52
Front Bezel ......................................................................................................................................... 53
Front Bezel Security ........................................................................................................................... 54
Bezel Blanks ....................................................................................................................................... 56
Memory .............................................................................................................................................. 57
DIMMs ............................................................................................................................... 57
DDR3-SDRAM DIMMs ...................................................................................................... 57
Populating DIMM Sockets ................................................................................................. 57
Installing DIMMs ................................................................................................................ 58
Expansion Cards ................................................................................................................................ 60
System Board Connections ................................................................................................................ 64
Drives ................................................................................................................................................. 66
Drive Positions ................................................................................................................... 68
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay ................................................. 68
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay .................................................... 69
Removing a Hard Drive from a Drive Bay .......................................................................... 72
Installing a Hard Drive into an Internal Drive Bay .............................................................. 72
Front Fan Assembly ........................................................................................................................... 76
Front I/O Assembly ............................................................................................................................. 78
Power Switch/LED Assembly ............................................................................................................. 79
Heat sink ............................................................................................................................................ 80
Processor ........................................................................................................................................... 82
Speaker .............................................................................................................................................. 85
Rear Chassis Fan ............................................................................................................................... 86
Power Supply ..................................................................................................................................... 88
System Board ..................................................................................................................................... 90
7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis ............................................ 91
Preparation for Disassembly .............................................................................................................. 91
Access Panel ...................................................................................................................................... 92
Front Bezel ......................................................................................................................................... 93
Front Bezel Security ........................................................................................................................... 94
Bezel Blanks ....................................................................................................................................... 96
Memory .............................................................................................................................................. 97
DIMMs ............................................................................................................................... 97
DDR3-SDRAM DIMMs ...................................................................................................... 97
Populating DIMM Sockets ................................................................................................. 97
Installing DIMMs ................................................................................................................ 98
Expansion Card ................................................................................................................................ 100
System Board Connections .............................................................................................................. 104
Drives ............................................................................................................................................... 105
vii
Drive Positions ................................................................................................................. 106
Installing and Removing Drives ....................................................................................... 106
Removing a 5.25-inch Drive from a Drive Bay ................................................ 107
Installing a 5.25-inch Drive into a Drive Bay ................................................... 108
Removing a 3.5-inch Drive from a Drive Bay .................................................. 111
Installing a 3.5-inch Drive into a Drive Bay ..................................................... 112
Removing and Replacing the Primary 3.5-inch Internal Hard Drive ................ 113
Fan duct ........................................................................................................................................... 116
Front Fan Assembly ......................................................................................................................... 117
Hood Sensor .................................................................................................................................... 119
Front I/O, Power Switch Assembly ................................................................................................... 120
Speaker ............................................................................................................................................ 122
Heat sink .......................................................................................................................................... 123
Processor ......................................................................................................................................... 125
Power Supply ................................................................................................................................... 128
System Board ................................................................................................................................... 130
Using the Small Form Factor Computer in a Tower Orientation ...................................................... 132
8 Troubleshooting Without Diagnostics ...................................................................................................... 133
Safety and Comfort .......................................................................................................................... 133
Before You Call for Technical Support ............................................................................................. 133
Helpful Hints ..................................................................................................................................... 134
Solving General Problems ................................................................................................................ 136
Solving Power Problems .................................................................................................................. 140
Solving Diskette Problems ............................................................................................................... 142
Solving Hard Drive Problems ........................................................................................................... 145
Solving Media Card Reader Problems ............................................................................................. 148
Solving Display Problems ................................................................................................................. 150
Solving Audio Problems ................................................................................................................... 154
Solving Printer Problems .................................................................................................................. 156
Solving Keyboard and Mouse Problems .......................................................................................... 158
Solving Hardware Installation Problems ........................................................................................... 160
Solving Network Problems ............................................................................................................... 161
Solving Memory Problems ............................................................................................................... 164
Solving Processor Problems ............................................................................................................ 166
Solving CD-ROM and DVD Problems .............................................................................................. 166
Solving USB Flash Drive Problems .................................................................................................. 169
Solving Front Panel Component Problems ...................................................................................... 170
Solving Internet Access Problems .................................................................................................... 170
Solving Software Problems .............................................................................................................. 173
Contacting Customer Support .......................................................................................................... 174
viii
9 POST Error Messages ................................................................................................................................ 175
POST Numeric Codes and Text Messages ..................................................................................... 176
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes .............................................. 184
10 Password Security and Resetting CMOS ............................................................................................... 188
Resetting the Password Jumper ...................................................................................................... 189
Clearing and Resetting the CMOS ................................................................................................... 190
11 Backup and Recovery .............................................................................................................................. 192
Windows 7 – Backup and Recovery ................................................................................................. 192
Backing up your information ............................................................................................ 192
Performing a recovery ..................................................................................................... 194
Using the Windows recovery tools .................................................................. 194
Using F11 ........................................................................................................ 195
Using a Windows 7 operating system DVD (purchased separately) ............... 195
Appendix A Battery Replacement ................................................................................................................ 197
Appendix B Removing and Replacing a Removable 3.5-inch SATA Hard Drive ..................................... 200
Appendix C Unlocking the Smart Cover Lock ............................................................................................ 205
Smart Cover FailSafe Key ................................................................................................................ 205
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock ......................................... 206
Appendix D Power Cord Set Requirements ................................................................................................ 208
General Requirements ..................................................................................................................... 208
Japanese Power Cord Requirements .............................................................................................. 208
Country-Specific Requirements ........................................................................................................ 209
Appendix E Specifications ............................................................................................................................ 210
MT Specifications ............................................................................................................................. 210
SFF Specifications ........................................................................................................................... 212
Index ................................................................................................................................................................. 213
ix
x
1
Product Features
Standard Configuration Features
Features may vary depending on the model. For a complete listing of the hardware and software
installed in the computer, run the diagnostic utility (included on some computer models only).
Figure 1-1 Microtower Configuration
Figure 1-2 Small Form Factor Configuration
Standard Configuration Features
1
NOTE: The Small Form Factor computer can also be used in a tower orientation. For more
information, see Using the Small Form Factor Computer in a Tower Orientation on page 132 in this
guide.
Microtower (MT) Front Panel Components
Drive configuration may vary by model. Some models have a bezel blank covering one or more drive
bays.
Table 1-1 Front Panel Components
1
5.25-inch Optical Drives
5
3.5-inch Media Card Reader (optional)
2
Hard Drive Activity Light
6
Dual-State Power Button
3
Microphone/Headphone Connector
7
Power On Light
4
USB (Universal Serial Bus) 2.0 Ports
8
Headphone Connector
NOTE: When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if
you want to use the connector for a microphone Line-In device or a headphone. You can reconfigure the
connector at any time by double-clicking the Realtek HD Audio Manager icon in the Windows taskbar.
NOTE: The Power On Light is normally green when the power is on. If it is flashing red, there is a problem with
the computer and it is displaying a diagnostic code. Refer to Interpreting POST Diagnostic Front Panel LEDs and
Audible Codes on page 184 to interpret the code.
2
Chapter 1 Product Features
Small Form Factor (SFF) Front Panel Components
Drive configuration may vary by model. Some models have a bezel blank covering one or more drive
bays.
Figure 1-3 Front Panel Components
Table 1-2 Front Panel Components
1
5.25-inch Optical Drive
5
Microphone/Headphone Connector
2
Dual-State Power Button
6
3.5-inch Media Card Reader (optional)
3
Power On Light
7
Hard Drive Activity Light
4
USB (Universal Serial Bus) Ports
8
Headphone Connector
NOTE: When a device is plugged into the Microphone/Headphone Connector, a dialog box will pop up asking if
you want to use the connector for a microphone Line-In device or a headphone. You can reconfigure the
connector at any time by double-clicking the Realtek HD Audio Manager icon in the Windows taskbar.
NOTE: The Power On Light is normally green when the power is on. If it is flashing red, there is a problem with
the computer and it is displaying a diagnostic code. Refer toInterpreting POST Diagnostic Front Panel LEDs and
Audible Codes on page 184 to interpret the code.
Small Form Factor (SFF) Front Panel Components
3
Microtower (MT) Rear Panel Components
Figure 1-4 Rear Panel Components
Table 1-3 Rear Panel Components
1
Power Cord Connector
6
Line-Out Connector for powered audio
devices (green)
2
Line-In Audio Connector (blue)
7
PS/2 Keyboard Connector (purple)
3
PS/2 Mouse Connector (green)
8
VGA Monitor Connector
4
Serial Connector
9
DisplayPort Monitor Connector
5
RJ-45 Network Connector
10
USB 3.0 ports (blue)
11
USB 2.0 ports (black)
NOTE: USB 3.0 ports are blue; USB 2.0 ports are black.
An optional second serial port and an optional parallel port are available from HP.
When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use
the connector for a line-in device or a microphone. You can reconfigure the connector at any time by doubleclicking the Realtek HD Audio Manager icon in the Windows taskbar.
The monitor connectors on the system board are inactive when a graphics card is installed in the computer.
If a graphics card is installed into one of the motherboard slots, the connectors on the graphics card and the
system board may be used at the same time. Some settings may need to be changed in Computer Setup to use
both connectors.
4
Chapter 1 Product Features
Small Form Factor (SFF) Rear Panel Components
Figure 1-5 Rear Panel Components
1
RJ-45 Network Connector
7
DisplayPort Monitor Connector
2
Serial Connector
8
VGA Monitor Connector
3
PS/2 Mouse Connector (green)
9
PS/2 Keyboard Connector (purple)
4
Power Cord Connector
10
Line-Out Connector for powered audio
devices (green)
5
USB 2.0 ports (black)
11
Line-In Audio Connector (blue)
6
USB 3.0 ports (blue)
NOTE: USB 3.0 ports are blue; USB 2.0 ports are black.
An optional second serial port and an optional parallel port are available from HP.
When a device is plugged into the blue Line-In Audio Connector, a dialog box will pop up asking if you want to use
the connector for a line-in device or a microphone. You can reconfigure the connector at any time by doubleclicking the Realtek HD Audio Manager icon in the Windows taskbar.
The monitor connectors on the system board are inactive when a graphics card is installed in the computer.
If a graphics card is installed into one of the motherboard slots, the connectors on the graphics card and the
system board may be used at the same time. Some settings may need to be changed in Computer Setup to use
both connectors.
Small Form Factor (SFF) Rear Panel Components
5
Serial Number Location
Each computer has a unique serial number and a product ID number that are located on the top
cover of the computer. Keep these numbers available for use when contacting customer service for
assistance.
Figure 1-6 Microtower Serial Number and Product ID Location
Figure 1-7 Small Form Factor Serial Number and Product ID Location
6
Chapter 1 Product Features
2
Installing and Customizing the
Software
If your computer was not shipped with a Microsoft operating system, some portions of this
documentation do not apply. Additional information is available in online help after you install the
operating system.
NOTE: If the computer was shipped with Windows 7 loaded, you will be prompted to register the
computer with HP Total Care before installing the operating system. You will see a brief movie
followed by an online registration form. Fill out the form, click the Begin button, and follow the
instructions on the screen.
CAUTION: Do not add optional hardware or third-party devices to the computer until the operating
system is successfully installed. Doing so may cause errors and prevent the operating system from
installing properly.
NOTE: Be sure there is a 10.2-cm (4-inch) clearance at the back of the unit and above the monitor
to permit the required airflow.
Installing the Windows Operating System
The first time you turn on the computer, the operating system is installed automatically. This process
takes about 5 to 10 minutes, depending on which operating system is being installed. Carefully read
and follow the instructions on the screen to complete the installation.
CAUTION: Once the automatic installation has begun, DO NOT TURN OFF THE COMPUTER
UNTIL THE PROCESS IS COMPLETE. Turning off the computer during the installation process may
damage the software that runs the computer or prevent its proper installation.
NOTE: If the computer shipped with more than one operating system language on the hard drive,
the installation process could take up to 60 minutes.
If your computer was not shipped with a Microsoft operating system, some portions of this
documentation do not apply. Additional information is available in online help after you install the
operating system.
Installing the Windows Operating System
7
Downloading Microsoft Windows Updates
1.
To set up your Internet connection, click Start > Internet Explorer and follow the instructions on
the screen.
2.
Once an Internet connection has been established, click the Start button.
3.
Select the All Programs menu.
4.
Click on the Windows Update link.
In Windows 7, the Windows Update screen appears. Click view available updates and make
sure all critical updates are selected. Click the Install button and follow the instructions on the
screen.
In Windows XP, you will be directed to the Microsoft Windows Update Web site. If you see
one or more pop-up windows that ask you to install a program from http://www.microsoft.com,
click Yes to install the program. Follow the instructions on the Microsoft Web site to scan for
updates and install critical updates and service packs.
It is recommended that you install all of the critical updates and service packs.
5.
After the updates have been installed, Windows will prompt you to reboot the machine. Be sure
to save any files or documents that you may have open before rebooting. Then select Yes to
reboot the machine.
Installing or Upgrading Device Drivers (Windows
systems)
When installing optional hardware devices after the operating system installation is complete, you
must also install the drivers for each of the devices.
If prompted for the i386 directory, replace the path specification with C:\i386, or use the Browse
button in the dialog box to locate the i386 folder. This action points the operating system to the
appropriate drivers.
Obtain the latest support software, including support software for the operating system from
http://www.hp.com/support. Select your country and language, select Download drivers and
software (and firmware), enter the model number of the computer, and press Enter.
Customizing the Monitor Display (Windows systems)
If you wish, you can select or change the monitor model, refresh rates, screen resolution, color
settings, font sizes, and power management settings. To do so, right-click on the Windows Desktop,
then click Personalize in Windows 7 or Properties in Windows XP to change display settings. For
more information, refer to the online documentation provided with the graphics controller utility or the
documentation that came with your monitor.
8
Chapter 2 Installing and Customizing the Software
Launching Windows XP from Windows 7
Windows XP Mode for Windows 7 allows you to install and launch Windows XP applications from the
Windows 7 taskbar. This feature is available on some computer models only.
To set up from a pre-installed Windows 7 desktop, click Start > Windows Virtual PC > Virtual
Windows XP and follow the instructions on the screen.
Accessing Disk Image (ISO) Files
There are disk image files (ISO files) included on your PC that contain the installation software for
additional software. These CD image files are located in the folder C:\SWSetup\ISOs. Each .iso file
can be burned to CD media to create an installation CD. It is recommended that these disks be
created and the software installed in order to get the most from your PC. The software and image file
names are:
●
Corel WinDVD SD and BD – installation software for WinDVD – used to play DVD movies
●
HP Insight Diagnostics OR Vision Diagnostics – software to perform diagnostic activities on your
PC
Launching Windows XP from Windows 7
9
3
Computer Setup (F10) Utility
Computer Setup (F10) Utilities
Use Computer Setup (F10) Utility to do the following:
10
●
Change factory default settings.
●
Set the system date and time.
●
Set, view, change, or verify the system configuration, including settings for processor, graphics,
memory, audio, storage, communications, and input devices.
●
Modify the boot order of bootable devices such as hard drives, optical drives, or USB flash
media devices.
●
Enable Quick Boot, which is faster than Full Boot but does not run all of the diagnostic tests run
during a Full Boot. You can set the system to:
❑
always Quick Boot (default);
❑
periodically Full Boot (from every 1 to 30 days); or
❑
always Full Boot.
●
Select Post Messages Enabled or Disabled to change the display status of Power-On Self-Test
(POST) messages. Post Messages Disabled suppresses most POST messages, such as
memory count, product name, and other non-error text messages. If a POST error occurs, the
error is displayed regardless of the mode selected. To manually switch to Post Messages
Enabled during POST, press any key (except F1 through F12).
●
Establish an Ownership Tag, the text of which is displayed each time the system is turned on or
restarted.
●
Enter the Asset Tag or property identification number assigned by the company to this computer.
●
Enable the power-on password prompt during system restarts (warm boots) as well as during
power-on.
●
Establish a setup password that controls access to the Computer Setup (F10) Utility and the
settings described in this section.
●
Secure integrated I/O functionality, including the serial, USB, or parallel ports, audio, or
embedded NIC, so that they cannot be used until they are unsecured.
●
Enable or disable removable media boot ability.
Chapter 3 Computer Setup (F10) Utility
●
Solve system configuration errors detected but not automatically fixed during the Power-On SelfTest (POST).
●
Replicate the system setup by saving system configuration information on a USB device and
restoring it on one or more computers.
●
Execute self-tests on a specified ATA hard drive (when supported by drive).
●
Enable or disable DriveLock security (when supported by drive).
Using Computer Setup (F10) Utilities
Computer Setup can be accessed only by turning the computer on or restarting the system.
To access the Computer Setup Utilities menu, complete the following steps:
1.
Turn on or restart the computer. If you are in Microsoft Windows, click Start > Shut Down >
Restart.
2.
Press either Esc or F10 while the “Press the ESC key for Startup Menu” message is displayed at
the bottom of the screen.
Pressing Esc displays a menu that allows you to access different options available at startup.
NOTE: If you do not press Esc or F10 at the appropriate time, you must restart the computer
and again press Esc or F10 when the monitor light turns green to access the utility.
3.
If you pressed Esc, press F10 to enter Computer Setup.
4.
A choice of five headings appears in the Computer Setup Utilities menu: File, Storage, Security,
Power, and Advanced.
5.
Use the arrow (left and right) keys to select the appropriate heading. Use the arrow (up and
down) keys to select the option you want, then press Enter. To return to the Computer Setup
Utilities menu, press Esc.
6.
To apply and save changes, select File > Save Changes and Exit.
●
If you have made changes that you do not want applied, select Ignore Changes and Exit.
●
To reset to factory settings or previously saved default settings (some models), select
Apply Defaults and Exit. This option will restore the original factory system defaults.
CAUTION: Do NOT turn the computer power OFF while the BIOS is saving the Computer Setup
(F10) changes because the CMOS could become corrupted. It is safe to turn off the computer only
after exiting the F10 Setup screen.
Table 3-1 Computer Setup (F10) Utility
Heading
Table
File
Computer Setup—File on page 12
Storage
Computer Setup—Storage on page 13
Security
Computer Setup—Security on page 16
Power
Computer Setup—Power on page 20
Advanced
Computer Setup—Advanced on page 21
Computer Setup (F10) Utilities
11
Computer Setup—File
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-2 Computer Setup—File
Option
Description
System Information
Lists:
●
Product name
●
SKU number (some models)
●
Processor type/speed/stepping
●
Cache size (L1/L2/L3) (dual core processors have this listed twice)
●
Installed memory size/speed, number of channels (single or dual) (if applicable)
●
Integrated MAC address for embedded, enabled NIC (if applicable)
●
System BIOS (includes family name and version)
●
Chassis serial number
●
Asset tracking number
●
ME firmware version
●
ME Management mode
About
Displays copyright notice.
Set Time and Date
Allows you to set system time and date.
Flash System ROM
Allows you to update the system ROM with a BIOS image file located on removable media.
Replicated Setup
Save to Removable Media
Saves system configuration, including CMOS, to a formatted USB flash media device.
Restore from Removable Media
Restores system configuration from a USB flash media device.
Default Setup
Save Current Settings as Default
Saves the current system configuration settings as the default.
Restore Factory Settings as Default
Restores the factory system configuration settings as the default.
12
Apply Defaults and
Exit
Applies the currently selected default settings and clears any established passwords.
Ignore Changes
and Exit
Exits Computer Setup without applying or saving any changes.
Save Changes and
Exit
Saves changes to system configuration or default settings and exits Computer Setup.
Chapter 3 Computer Setup (F10) Utility
Computer Setup—Storage
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-3 Computer Setup—Storage
Option
Description
Device Configuration
Lists all installed BIOS-controlled storage devices.
When a device is selected, detailed information and options are displayed. The following options
may be presented:
●
Hard Disk: Size, model, firmware version, serial number, connector color.
Translation mode (ATA disks only)
Lets you select the translation mode to be used for the device. This enables the BIOS to
access disks partitioned and formatted on other systems and may be necessary for users of
older versions of UNIX (e.g., SCO UNIX version 3.2). Options are Automatic, Bit-Shift,
LBA Assisted, User, and Off.
Available only when the drive translation mode is set to User, allows you to specify the
parameters (logical cylinders, heads, and sectors per track) used by the BIOS to translate
disk I/O requests (from the operating system or an application) into terms the hard drive can
accept. Logical cylinders may not exceed 1024. The number of heads may not exceed 256.
The number of sectors per track may not exceed 63.
CAUTION: Ordinarily, the translation mode selected automatically by the BIOS should not
be changed. If the selected translation mode is not compatible with the translation mode that
was active when the disk was partitioned and formatted, the data on the disk will be
inaccessible.
●
CD-ROM: Model, firmware version, serial number, connector color (not included for USB CDROM).
●
SSD Life Used
●
SMART (ATA disks only)
●
Diskette: Model and firmware version.
NOTE: Displays for USB diskette drives.
●
Default Values (ATA disks only)
See Translation Mode above for details.
SATA Defaults
Computer Setup (F10) Utilities
13
Table 3-3 Computer Setup—Storage (continued)
Storage Options
eSATA Port (some models)
Allows you to set a SATA port as an eSATA port for use with an external drive. Default is enabled.
This setting affects only the port with the black connector, labeled as eSATA on the system board.
This port should have the eSATA back panel connector attached to use eSATA drives. For more
information, see the eSATA white paper at www.hp.com.
NOTE: eSATA is not available on USDT systems.
SATA Emulation
Allows you to choose how the SATA controller and devices are accessed by the operating
system. There are three supported options: IDE, RAID, and AHCI (default).
IDE - This is the most backwards-compatible setting of the three options. Operating systems
usually do not require additional driver support in IDE mode.
RAID - Allows DOS and boot access to RAID volumes. Use this mode with the RAID device driver
loaded in the operating system to take advantage of RAID features.
AHCI (default option) - Allows operating systems with AHCI device drivers loaded to take
advantage of more advanced features of the SATA controller.
NOTE: The RAID/AHCI device driver must be installed prior to attempting to boot from a RAID/
AHCI volume. If you attempt to boot from a RAID/AHCI volume without the required device driver
installed, the system will crash (blue screen). RAID volumes may become corrupted if they are
booted to after disabling RAID.
NOTE: RAID is not available on USDT systems.
Removable Media Boot
Enables/disables ability to boot the system from removable media. Default is enabled.
Max eSATA Speed (some models)
Allows you to choose 1.5 Gbps or 3.0 Gpbs as the maximum eSATA speed. By default, the speed
is limited to 1.5 Gbps for maximum reliability.
CAUTION: Consult your eSATA drive and cable manufacturer before enabling 3.0 Gpbs speed.
Some drive and cable combinations may not run reliably at 3.0 Gpbs.
14
Chapter 3 Computer Setup (F10) Utility
Table 3-3 Computer Setup—Storage (continued)
DPS Self-Test
Allows you to execute self-tests on ATA hard drives capable of performing the Drive Protection
System (DPS) self-tests.
NOTE: This selection will only appear when at least one drive capable of performing the DPS
self-tests is attached to the system.
Boot Order
Allows you to:
●
EFI Boot Sources: Specify the order in which EFI boot sources (such as a internal hard
drive, USB hard drive, USB optical drive, or internal optical drive) are checked for a bootable
operating system image. Each device on the list may be individually excluded from or
included for consideration as a bootable operating system source.
EFI boot sources always have precedence over legacy boot sources.
●
Legacy Boot Sources:Specify the order in which legacy boot sources (such as a network
interface card, internal hard drive, USB optical drive, or internal optical drive) are checked for
a bootable operating system image. Each device on the list may be individually excluded
from or included for consideration as a bootable operating system source.
Specify the order of attached hard drives. The first hard drive in the order will have priority in
the boot sequence and will be recognized as drive C (if any devices are attached).
NOTE: You can use F5 to disable individual boot items, as well as disable EFI boot and/or
legacy boot.
NOTE: MS-DOS drive lettering assignments may not apply after a non-MS-DOS operating
system has started.
Shortcut to Temporarily Override Boot Order
To boot one time from a device other than the default device specified in Boot Order, restart the
computer and press Esc (to access the boot menu) and then F9 (Boot Order), or only F9 (skipping
the boot menu) when the monitor light turns green. After POST is completed, a list of bootable
devices is displayed. Use the arrow keys to select the preferred bootable device and press Enter.
The computer then boots from the selected non-default device for this one time.
Computer Setup (F10) Utilities
15
Computer Setup—Security
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-4 Computer Setup—Security
Option
Description
Setup Password
Allows you to set and enable a setup (administrator) password.
NOTE: If the setup password is set, it is required to change Computer Setup options, flash the
ROM, and make changes to certain plug and play settings under Windows.
NOTE: This selection will only appear when at least one drive that supports the DriveLock
feature is attached to the system.
See the Desktop Management Guide for more information.
Power-On Password
Allows you to set and enable a power-on password. The power-on password prompt appears
after a power cycle. If the user does not enter the correct power-on password, the unit will not
boot.
NOTE: This selection will only appear when at least one drive that supports the DriveLock
feature is attached to the system.
See the Desktop Management Guide for more information.
Password Options
Allows you to enable/disable:
(This selection appears
only if a power-on
password or setup
password is set.)
●
Lock Legacy Resources (appears if a setup password is set). Default is enabled.
●
Setup Browse Mode (appears if a setup password is set) (allows viewing, but not changing,
the F10 Setup Options without entering setup password). Default is enabled.
●
Password prompt on F9, F11, & F12 (allows access to menus without entering setup
password). Default is enabled.
●
Network Server Mode (appears if a power-on password is set). Default is disabled.
See the Desktop Management Guide for more information.
Smart Cover (some
models)
Allows you to:
●
Lock/unlock the Cover Lock.
●
Set the Cover Removal Sensor to Disable/Notify User/Setup Password.
NOTE: Notify User alerts the user that the sensor has detected that the cover has been
removed. Setup Password requires that the setup password be entered to boot the computer if
the sensor detects that the cover has been removed.
This feature is supported on some models only. See the Desktop Management Guide for more
information.
16
Chapter 3 Computer Setup (F10) Utility
Table 3-4 Computer Setup—Security (continued)
Device Security
Allows you to set Device Available/Device Hidden (default is Device Available) for:
●
Embedded security device (some models)
●
System audio
●
Network controller
NOTE: You must disable AMT before trying to hide the network controller.
USB Security
●
Serial ports (some models)
●
Parallel port (some models)
●
SATA0
●
SATA1
●
SATA2 (some models)
●
SATA3 (some models)
●
SATA4 (some models)
Allows you to set Enabled/Disabled (default is Enabled) for:
●
●
●
Front USB Ports
◦
USB Port 1
◦
USB Port 2
◦
USB Port 3
◦
USB Port 4
Rear USB Ports
◦
USB Port 1
◦
USB Port 2
◦
USB Port 3
◦
USB Port 4
◦
USB Port 5
◦
USB Port 6
Accessory USB Ports
◦
USB Port 1
◦
USB Port 2
◦
USB Port 3 (some models)
◦
USB Port 4 (some models)
Slot Security
Allows you to disable any PCI or PCI Express slot. Default is enabled.
Network Boot
Enables/disables the computer’s ability to boot from an operating system installed on a network
server. (Feature available on NIC models only; the network controller must be either a PCI
expansion card or embedded on the system board.) Default is enabled.
Computer Setup (F10) Utilities
17
Table 3-4 Computer Setup—Security (continued)
System IDs
Master Boot Record
Security
Allows you to set:
●
Asset tag (18-byte identifier), a property identification number assigned by the company to
the computer.
●
Ownership tag (80-byte identifier) displayed during POST.
●
Universal Unique Identifier (UUID) number. The UUID can only be updated if the current
chassis serial number is invalid. (These ID numbers are normally set in the factory and are
used to uniquely identify the system.)
●
Keyboard locale setting for System ID entry.
Enables/disables Master Boot Record (MBR) security.
The MBR contains information needed to successfully boot from a disk and to access the data
stored on the disk. Master Boot Record Security may prevent unintentional or malicious changes
to the MBR, such as those caused by some viruses or by the incorrect use of certain disk utilities.
It also allows you to recover the "last known good" MBR, should changes to the MBR be detected
when the system is restarted.
When MBR Security is enabled, the BIOS prevents any changes being made to the MBR of the
current bootable disk while in MS-DOS or Windows Safe Mode.
NOTE: Most operating systems control access to the MBR of the current bootable disk; the
BIOS cannot prevent changes that may occur while the operating system is running.
18
Chapter 3 Computer Setup (F10) Utility
Table 3-4 Computer Setup—Security (continued)
System Security
(some models: these
options are hardware
dependent)
Data Execution Prevention (enable/disable) - Helps prevent operating system security breaches.
Default is enabled.
Virtualization Technology (VTx)(some models) (enable/disable) - Controls the virtualization
features of the processor. Changing this setting requires turning the computer off and then back
on. Default is disabled.
Virtualization Technology Directed I/O (VTd) (some models) (enable/disable) - Controls
virtualization DMA remapping features of the chipset. Changing this setting requires turning the
computer off and then back on. Default is disabled.
Trusted Execution Technology (enable/disable) — Enabling automatically enables VTx and VTd
and disable OS Management of Embedded Security Device. Embedded Security Device must be
enabled to enable this feature.
Intel TXT (LT) Support (some models) (enable/disable) - Controls the underlying processor and
chipset features needed to support a virtual appliance. Changing this setting requires turning the
computer off and then back on. Default is disabled. To enable this feature you must enable the
following features:
●
Embedded Security Device Support
●
Virtualization Technology
●
Virtualization Technology Directed I/O
Embedded Security Device (some models) (enable/disable) - Permits activation and deactivation
of the Embedded Security Device. Changing this setting requires turning the computer off and
then back on.
NOTE: To configure the Embedded Security Device, a Setup password must be set.
●
Reset to Factory Settings (some models) (Do not reset/Reset) - Resetting to factory defaults
will erase all security keys. Changing this setting requires turning the computer off and then
back on. Default is Do not reset.
CAUTION: The embedded security device is a critical component of many security
schemes. Erasing the security keys will prevent access to data protected by the Embedded
Security Device. Choosing Reset to Factory Settings may result in significant data loss.
OS management of Embedded Security Device (some models) (enable/disable) - This option
allows the user to limit operating system control of the Embedded Security Device. Changing this
setting requires turning the computer off and then back on. This option allows the user to limit OS
control of the Embedded Security Device. Default is enabled. This option is automatically disabled
if Trusted Execution Technology is enabled.
Reset of Embedded Security Device through OS (some models) (enable/disable) - This option
allows the user to limit the operating system ability to request a Reset to Factory Settings of the
Embedded Security Device. Changing this setting requires turning the computer off and then back
on. Default is disabled.
NOTE: To enable this option, a Setup password must be set.
DriveLock Security
Allows you to assign or modify a master or user password for hard drives. When this feature is
enabled, the user is prompted to provide one of the DriveLock passwords during POST. If neither
is successfully entered, the hard drive will remain inaccessible until one of the passwords is
successfully provided during a subsequent cold-boot sequence.
NOTE: This selection will only appear when at least one drive that supports the DriveLock
feature is attached to the system.
See the Desktop Management Guide for more information.
Computer Setup (F10) Utilities
19
Computer Setup—Power
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-5 Computer Setup—Power
Option
Description
OS Power
Management
●
Runtime Power Management— Enable/Disable. Allows certain operating systems to reduce
processor voltage and frequency when the current software load does not require the full
capabilities of the processor. Default is enabled.
●
Idle Power Savings—Extended/Normal. Allows certain operating systems to decrease the
processors power consumption when the processor is idle. Default is extended.
●
ACPI S3 Hard Disk Reset — Enable/disable. Enabling this causes the BIOS to ensure hard
disks are ready to accept commands after resuming from S3 before returning control to the
operating system.
●
Unique Sleep State Blink Rates—Enable/Disable. This feature is designed to provide a
visual indication of what sleep state the system is in. Each sleep state has a unique blink
pattern. Default is disabled.
◦
S0 (On) = Solid green LED.
◦
S3 (Stand By)= 3 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds
(green LED) — repeated cycles of 3 blinks and a pause.
◦
S4 (Hibernation)= 4 blinks at 1Hz (50% duty cycle) followed by a pause of 2 seconds
(green LED) — repeated cycles of 4 blinks and a pause.
◦
S5 (Soft Off) = LED is off.
NOTE: If this feature is disabled, S4 and S5 both have the LED off. S1 (no longer
supported) and S3 use 1 blink per second.
Hardware Power
Management
SATA Power Management – Enables or disables SATA bus and/or device power management.
Default is enabled.
S5 Maximum Power Savings—Turns off power to all nonessential hardware when system is off to
meet EUP Lot 6 requirement of less than 1 Watt power usage. Default is disabled.
Thermal
Fan idle mode—This bar graph controls the minimum permitted fan speed.
NOTE: This setting only changes the minimum fan speed. The fans are still automatically
controlled.
20
Chapter 3 Computer Setup (F10) Utility
Computer Setup—Advanced
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Table 3-6 Computer Setup—Advanced (for advanced users)
Option
Heading
Power-On Options
Allows you to set:
●
POST mode (QuickBoot, Clear Memory, FullBoot, or FullBoot Every x Days).
◦
QuickBoot (default) = Do not clear memory or perform a memory test.
◦
FullBoot = Memory test (count) on cold boot. Clears memory on all boots.
◦
Clear Memory = No memory count on cold boot. Clears memory on all boots.
◦
FullBoot Every x Days = Memory count on 1st cold boot on or after the xth day. No
more memory counts until 1st cold boot on or after x days. Clears memory on all boots.
●
POST messages (enable/disable). Default is disabled.
●
Press the ESC key for Startup Menu (Enable/Disable). Default is enabled.
●
Option ROM Prompt (enable/disable). Enabling this feature will cause the system to display
a message before loading option ROMs. Default is enabled.
●
After Power Loss (off/on/previous state). Default is Power off. Setting this option to:
◦
Off—causes the computer to remain powered off when power is restored.
◦
On—causes the computer to power on automatically as soon as power is restored.
◦
Previous state—causes the computer to power on automatically as soon as power is
restored, if it was on when power was lost.
NOTE: If you turn off power to the computer using the switch on a power strip, you will not be
able to use the suspend/sleep feature or the Remote Management features.
●
POST Delay (in seconds). Enabling this feature will add a user-specified delay to the POST
process. This delay is sometimes needed for hard disks on some PCI cards that spin up very
slowly, so slowly that they are not ready to boot by the time POST is finished. The POST
delay also gives you more time to select F10 to enter Computer (F10) Setup. Default is
None.
●
Remote Wakeup Boot Source (remote server/local hard drive). Default is Local hard drive.
●
Factory Recovery Boot Support (Enable/Disable). Provides the ability for the BIOS to redirect
the boot to the recovery partition on the user hard drive, if present. Some versions of the
recovery software honor the F11 key press even when this feature is disabled by the BIOS.
Default is disabled.
●
Bypass F1 Prompt on Configuration Changes (Enable/Disable). Allows you to set the
computer not to confirm when changes were made. Default is disabled.
BIOS Power-On
Allows you to set the computer to turn on automatically at a time you specify.
Onboard Devices
Allows you to set resources for or disable Legacy devices.
Select the Legacy device's IRQ, DMA, and I/O Range. The settings may not take effect for all
operating systems. To hide a device from the operating system, see Security > Device Security.
Computer Setup (F10) Utilities
21
Table 3-6 Computer Setup—Advanced (for advanced users) (continued)
Bus Options
Device Options
22
On some models, allows you to enable or disable:
●
PCI SERR# Generation. Default is enabled.
●
PCI VGA Palette Snooping, which sets the VGA palette snooping bit in PCI configuration
space; only needed when more than one graphics controller is installed. Default is disabled.
Allows you to set:
●
Monitor Tracking (enable/disable). Allows ROM to save monitor asset information. Default is
disabled.
●
Printer mode (Bi-Directional, EPP + ECP, Output Only). Default is EPP+ECP.
●
Num Lock State at Power-On (off/on). Default is off.
●
Integrated Video (enable/disable). Use this option to disable the integrated video controller
when another video controller is present in the system. Default is enabled.
●
Internal Speaker (some models) (does not affect external speakers). Default is enabled.
●
NIC Option ROM Download (PXE, iSCSI, disabled). The BIOS contains an embedded NIC
option ROM to allow the unit to boot through the network to a PXE server. This is typically
used to download a corporate image to a hard drive. The NIC option ROM takes up memory
space below 1MB commonly referred to as DOS Compatibility Hole (DCH) space. This
space is limited. This F10 option will allow users to disable the downloading of this
embedded NIC option ROM thus giving more DCH space for additional PCI cards which may
need option ROM space. The default will be to have the NIC option-ROM-enabled. Default is
PXE.
●
SATA RAID Option ROM Download (enable/disable). The BIOS contains an embedded
SATA RAID option ROM for RAID support. This can be temporarily disabled to save DCH
space. Note that with the option ROM disabled, users will be unable to boot to hard drives in
the system while running in RAID mode. Default is disabled.
●
Multi-Processor (enable/disable). Use this option to disable multi-processor support under
the OS. Default is enabled.
●
Hyper threading (enable/disable) (some models). Use this option to disable processor hyperthreading.
●
Turbo Mode (enable/disable). Allows you to enable and disable the Intel Turbo Mode feature,
which allows one core of the system to run at a higher than standard frequency and power if
other cores are idle. Default is enabled.
Chapter 3 Computer Setup (F10) Utility
Table 3-6 Computer Setup—Advanced (for advanced users) (continued)
VGA Configuration
Displayed only if there is an add-in video card in the system. Allows you to specify which VGA
controller will be the “boot” or primary VGA controller.
AMT Configuration
Allows you to set:
●
AMT (enable/disable). Allows you to enable or disable functions of the embedded
Management Engine (ME) such as Active Management Technology (AMT). If set to disable,
the Management Engine is set to a temporarily disabled state and will not provide functions
beyond necessary system configuration. Default is enabled.
●
Unconfigure AMT/ME (enable/disable). Allows you to unconfigure any provisioned
management settings for AMT. The AMT settings are restored to factory defaults. This
feature should be used with caution as AMT will not be able to provide any set AMT
management functions once unconfigured. Default is disabled.
●
Hide Unconfigure ME Confirmation Prompt (enable/disable). Allows you to set the system to
not display the confirmation to unconfigure ME.
●
Watchdog Timer (enable/disable). Allows you to set amount of time for a operating system
and BIOS watchdog alert to be sent if the timers are not deactivated. BIOS watchdog is
deactivated by BIOS and would indicate that a halt occurred during execution if the alert is
sent to the management console. An operating system alert is deactivated by the operating
system image and would indicate that a hang occurred during its initialization. Default is
enabled.
Recovering the Configuration Settings
This method of recovery requires that you first perform the Save to Removable Media command
with the Computer Setup (F10) Utility before Restore is needed. (See Save to Removable Media
on page 12 in the Computer Setup—File table.)
NOTE: It is recommended that you save any modified computer configuration settings to a USB
flash media device and save the device for possible future use.
To restore the configuration, insert the USB flash media device with the saved configuration and
perform the Restore from Removable Media command with the Computer Setup (F10) Utility. (See
Restore from Removable Media on page 12 in the Computer Setup—File table.)
Recovering the Configuration Settings
23
4
Illustrated parts catalog
Microtower (MT) chassis spare parts
Computer major components
24
Item
Description
(1)
Front bezel
Spare part number
For use in all countries and regions except China
689377-001
For use in China
689378-001
5.25-inch bezel blank (optical drive; not illustrated)
570838-001
Chapter 4 Illustrated parts catalog
Item
Description
Spare part number
3.5-inch bezel blank (not illustrated)
583653-001
(2)
Access panel
646825-001
(3)
Power supply
(4)
320W, 90% efficient
613764-001
320W, standard
613765-001
System board (includes replacement thermal material)
657239-001
Memory modules (PC3-12800, 1600-MHz; not illustrated)
8-GB
689375-001
4-GB
671613-001
2-GB
671612-001
Processors (include replacement thermal material; not illustrated)
Intel Core i7 processor
3770, 3.4 GHz, 8-MB L3 cache, 95W
688164-001
Intel Core i5 processors
3570, 3.4 GHz, 6-MB L3 cache, 95W
688162-001
3470, 3.2 GHz, 6-MB L3 cache, 95W
687943-001
Intel Core i3 processors
3240, 3.4 GHz, 3-MB L3 cache
688951-001
3225, 3.3 GHz, 3-MB L3 cache, 55W
689578-001
3220, 3.3 GHz, 3-MB L3 cache, 65W
688950-001
2130, 3.4 GHz, 3-MB L3 cache
665120-001
2120, 3.3 GHz, 3-MB L3 cache
638629-001
Intel Pentium processors
G870, 3.1 GHz, 3-MB L3 cache
G860, 3.0 GHz, 3-MB L3 cache
691936-001
G850, 2.9 GHz, 3-MB L3 cache
655973-001
G640, 2.8 GHz, 3-MB L3 cache
691935-001
G630, 2.7 GHz, 3-MB L3 cache
665122-001
Intel Celeron processors
G550, 2.6 GHz, 2-MB L3 cache
691934-001
G540, 2.5 GHz, 2-MB L3 cache
665119-001
G530T, 2.0 GHz, 2-MB L3 cache
665118-001
Microtower (MT) chassis spare parts
25
Cables
26
Item
Description
Spare part number
(1)
Front I/O assembly
646827-001
(2)
SATA optical drive power cable
646834-001
(3)
SATA hard drive power cable
646833-001
(4)
Power switch/LED assembly
646828-001
(5)
SATA cable, 18 inch, 1 straight end, 1 angled end (labeled; not illustrated)
646830-001
(6)
SATA cable, 17.7 inch, 2 straight ends
639959-001
DMS-59 to dual VGA cable
463023-001
Adapter, DisplayPort to VGA
632484-001
Adapter, DisplayPort to DVI
662723-001
Adapter, DVI to VGA
657401-001
Adapter, DisplayPort to HDMI
617450-001
DisplayPort cable
487562-001
SATA power extension cable
633756-001
Chapter 4 Illustrated parts catalog
Misc parts
Item
Description
Spare part number
(1)
Heat sink (includes replacement thermal material)
645326-001
(2)
Fan with guard
585884-001
(3)
Hood sensor
638816-001
(4)
Speaker
645330-001
(5)
Solenoid lock
641498-001
(6)
Rear chassis fan
636922-001
(7)
Printer port, PCI card (not illustrated)
638817-001
Fan duct assembly
646824-001
Serial port, PCI card (not illustrated)
638815-001
2.5-in drive adapter (not illustrated)
586721-001
Hard drive conversion bracket
397117-001
Grommet, hard drive isolation, blue (not illustrated)
450712-001
Card reader, 22-in-1 (not illustrated)
636166-001
USB powered speakers (not illustrated)
636917-001
Mouse (not illustrated)
Mouse, PS2, optical, jack black (non-ECO)
609250-001
USB, optical, jack black
537749-001
Microtower (MT) chassis spare parts
27
Item
Description
Spare part number
Washable
619580-001
Wireless
674317-001
Transceiver for use with wireless mouse and keyboard
674319-001
eSATA port assembly, PCI card (not illustrated)
645558-001
Clamp lock, includes universal cable (plate not included; not illustrated)
508987-001
Antenna for use with 538048-001 (not illustrated)
583345-001
HP Business Digital Headset (not illustrated)
642738-001
External USB Webcam (not illustrated)
609252-001
Keyboards (not illustrated)
PS/2, basic
537745-xx1
USB, basic
537746-xx1
USB, mini
674314-xx1
Washable
613125-xx1
Smart card
631411-xx1
Screw Kit - misc screws
330458-001
Screw Kit - tamper resistant screws
393956-001
Drives
Description
Spare part number
Hard drive
1-TB, 7200-rpm
636930-001
500-GB, 7200-rpm
636929-001
320-GB, 7200-rpm, 2.5-inch
634824-001
250-GB, 7200-rpm
636927-001
256-GB Solid-state Drive (SSD), self-encrypting (SED), SATA 6.0
680020-001
160-GB Solid-state Drive (SSD), SATA 3.0
646809-001
128-GB Solid-state Drive (SSD), SATA 2.0
665961-001
120-GB Solid-state Drive (SSD), SATA 2.0
661841-001
Optical drive
28
Blu-ray BD-Writer XL Drive
682219-001
Blu-ray BD-RW SuperMulti DL Drive
656792-001
16X SATA DVD±RW drive
660408-001
Chapter 4 Illustrated parts catalog
Description
Spare part number
16X SATA DVD-ROM drive
581599-001
Grommet, hard drive isolation, blue
450712-001
Misc boards
Description
Spare part number
GeForce GT630 PCIe x16 graphics card, 2 GB
684591-001
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
680653-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
632486-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
682411-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637213-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
637995-001
HP FireWire / IEEE 1394a PCIe x1 Card
637591-001
Intel PRO/1000CT2 NIC, includes bracket
635523-001
HP WLAN 802.11 g/n 1x2 PCIe NIC
538048-001
Sequential part number listing
Spare part
number
Description
330458-001
Screw Kit
336445-001
Feet
393956-001
Screw Kit - tamper resistant screws
397117-001
Hard drive conversion bracket
450712-001
Grommet, hard drive isolation, blue
463023-001
DMS-59 to dual VGA cable
487562-001
DisplayPort cable
508987-001
Clamp lock, includes universal cable (plate not included)
537745-xx1
PS/2 basic keyboard
537746-xx1
USB basic keyboard
537749-001
Mouse, USB, optical, jack black
538048-001
HP WLAN 802.11b/g/n card
570580-001
Mouse, USB, laser (non-ECO)
570838-001
Bezel blank, optical drive, 5.25-inch
581599-001
16X SATA DVD-ROM drive
Microtower (MT) chassis spare parts
29
30
Spare part
number
Description
583345-001
Antenna for use with 538048-001
583653-001
Bezel blank, 3.5-inch
585884-001
Chassis fan with guard
586721-001
2.5-in drive adapter
609250-001
Mouse, PS2, optical, jack black (non-ECO)
609252-001
External USB webcam
613125-xx1
Washable keyboard
613764-001
320W, 90% efficient
613765-001
320W, standard
617450-001
Adapter, DisplayPort to HDMI
619580-001
Mouse, washable
631411-xx4
Smart card keyboard
632484-001
Adapter, DisplayPort to VGA
632486-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
633756-001
SATA power extension cable
634824-001
320-GB, 7200-rpm hard drive, 2.5 inch, SED
635523-001
Intel PRO/1000CT2 NIC, includes bracket
636166-001
Card reader, 22-in-1
636917-001
USB powered speakers
636922-001
Chassis fan
636927-001
250-GB, 7200-rpm hard drive
636929-001
500-GB, 7200-rpm hard drive
636930-001
1-TB, 7200-rpm hard drive
637213-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637591-001
HP FireWire / IEEE 1394a PCIe x1 card
637995-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
638629-001
Intel Core i3 2120 (3.3-GHz, 3-MB L3 cache)
638815-001
Serial port PCI card
638816-001
Hood sensor
638817-001
Printer port, PCI card
639959-001
SATA cable, 17.7 inch, 2 straight ends
641498-001
Solenoid lock
642738-001
HP Business Digital Headset
645326-001
Heat sink (includes replacement thermal material)
Chapter 4 Illustrated parts catalog
Spare part
number
Description
645330-001
Speaker
645558-001
eSATA port assembly, PCI card
646809-001
160-GB Solid-state drive, SATA 3.0
646824-001
Fan duct assembly
646825-001
Access panel
646827-001
Front I/O assembly
646828-001
Power switch/LED with holder
646830-001
SATA cable, 18 inch, 1 straight end, 1 angled end
646833-001
Hard drive power cable
646834-001
Optical drive power cable
655973-001
Intel Pentium G850 (2.9-GHz, 3-MB L3 cache)
656792-001
Blu-ray BD-RW DL drive
657239-001
System board (includes replacement thermal material)
657401-001
Adapter, DVI to VGA
660408-001
DVD±RW drive
661841-001
120-GB Solid-state drive, SATA 2.0
662723-001
Adapter, DisplayPort to DVI
665118-001
Intel Celeron G530T (2.0-GHz, 2-MB L3 cache)
665119-001
Intel Celeron G540 (2.5-GHz, 2-MB L3 cache)
665120-001
Intel Core i3 2130 (3.4-GHz, 3-MB L3 cache)
665122-001
Intel Pentium G630 (2.7-GHz, 3-MB L3 cache)
665123-001
Intel Pentium G860 (3.0-GHz, 3-MB L3 cache)
665961-001
128-GB Solid-state drive, SATA 2.0
671612-001
Memory module, 2-GB, PC3 12800, CL11)
671613-001
Memory module, 4-GB, PC3 10600, 1333-MH
674314-xx1
Keyboard, wireless
674317-001
Mouse, wireless
674319-001
Transceiver for use with wireless mouse and keyboard
680020-001
256-GB Solid-state drive, self-encrypting (SED), SATA 6.0
680653-001
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
682219-001
Blu-ray BD-Writer XL Drive
682410-001
Intel Celeron G460 processor (1.7-GHz, 1-MB L3 cache)
682411-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
684591-001
GeForce GT630 PCIe x16 graphics card, 2 GB
Microtower (MT) chassis spare parts
31
32
Spare part
number
Description
687943-001
Intel Core i5 3470 procoessor (3.2-GHz, 6-MB L3 cache)
688162-001
Intel Core i5 3570 (3.4-GHz, 6-MB L3 cache)
688164-001
Intel Core i7 3770 (3.4-GHz, 8-MB L3 cache)
688950-001
Intel Core i3 3220 (3.3-GHz, 3-MB L3 cache, 65-W)
688951-001
Intel Core i3 3240 (3.4-GHz, 3-MB L3 cache)
689375-001
Memory module, 8-GB, PC3 12800, CL11
689377-001
Front bezel for use in all countries and regions except China
689378-001
Front bezel for use in China
689578-001
Intel Core i3 3225 (3.4-GHz, 3-MB L3 cache, 55-W)
691934-001
Intel Celeron G550 (2.6-GHz, 2-MB L3 cache)
691935-001
Intel Pentium G640 (2.8-GHz, 3-MB L3 cache)
691936-001
Intel Pentium G870 (3.1-GHz, 3-MB L3 cache)
696442-001
500-GB hard drive, 7200-rpm, 2.5-inch, SED
696622-001
180-GB Solid-state drive, SATA 6.0
Chapter 4 Illustrated parts catalog
Small Form Factor (SFF) chassis spare parts
Computer major components
Item
Description
Spare part number
(1)
Front bezel
687950-001
Bezel blank (optical drive; not illustrated)
570838-001
Bezel blank (diskette drive; not illustrated)
583653-001
(2)
Access panel
646815-001
(3)
Power supply
(4)
240W, 90% efficient
613762-001
240W, standard
613763-001
System board (includes replacement thermal material)
657239-001
Memory modules (PC3-12800, 1600-MHz; not illustrated)
8-GB
689375-001
4-GB
671613-001
2-GB
671612-001
Small Form Factor (SFF) chassis spare parts
33
Item
Description
Spare part number
Processors (include replacement thermal material; not illustrated)
Intel Core i7 processor
3770, 3.4 GHz, 8-MB L3 cache, 95W
688164-001
Intel Core i5 processors
3570, 3.4 GHz, 6-MB L3 cache, 95W
688162-001
3470, 3.2 GHz, 6-MB L3 cache, 95W
687943-001
Intel Core i3 processors
3240, 3.4 GHz, 3-MB L3 cache
688951-001
3225, 3.3 GHz, 3-MB L3 cache, 55W
689578-001
3220, 3.3 GHz, 3-MB L3 cache, 65W
688950-001
2130, 3.4 GHz, 3-MB L3 cache
665120-001
2120, 3.3 GHz, 3-MB L3 cache
638629-001
Intel Pentium processors
G870, 3.1 GHz, 3-MB L3 cache
G860, 3.0 GHz, 3-MB L3 cache
691936-001
G850, 2.9 GHz, 3-MB L3 cache
655973-001
G640, 2.8 GHz, 3-MB L3 cache
691935-001
G630, 2.7 GHz, 3-MB L3 cache
665122-001
Intel Celeron processors
34
G550, 2.6 GHz, 2-MB L3 cache
691934-001
G540, 2.5 GHz, 2-MB L3 cache
665119-001
G530T, 2.0 GHz, 2-MB L3 cache
665118-001
G460, 1.7 GHz, 1-MB L3 cache
682410-001
Chapter 4 Illustrated parts catalog
Cables
Item
Description
Spare part number
(1)
Front I/O and power switch assembly
636926-001
(2)
SATA cable, 19.5 inch, 2 straight ends
638813-001
(3)
SATA drive power cable
636923-001
SATA cable, 25.2 inch, 1 straight end, 1 angled end (not illustrated)
638814-001
DMS-59 to dual VGA cable
463023-001
Adapter, DisplayPort to VGA
632484-001
Adapter, DisplayPort to DVI
662723-001
Adapter, DVI to VGA
657401-001
Adapter, DisplayPort to HDMI
617450-001
DisplayPort cable
487562-001
SATA power extension cable
633756-001
Small Form Factor (SFF) chassis spare parts
35
Misc parts
36
Item
Description
Spare part number
(1)
Chassis fan
645327-001
(2)
Fan duct (not illustrated)
636921-001
(3)
Heat sink (includes replacement thermal material)
645326-001
(4)
Speaker
636925-001
(5)
Solenoid lock
641471-001
(6)
Printer port, PCI card
638817-001
(7)
Hood sensor
638816-001
Rubber feet
583654-001
Chassis stand
587451-001
Chapter 4 Illustrated parts catalog
Item
Description
Spare part number
Serial port, PCI card (not illustrated)
638815-001
2.5-in drive adapter (not illustrated)
586721-001
Hard drive conversion bracket
397117-001
Grommet, hard drive isolation, blue (not illustrated)
450712-001
Card reader, 22-in-1 (not illustrated)
636166-001
USB powered speakers (not illustrated)
636917-001
Mouse (not illustrated)
USB, optical, jack black
537749-001
Washable
619580-001
Wireless
674317-001
Transceiver for use with wireless mouse and keyboard
674319-001
Mouse, USB, laser (non-ECO)
570580-001
Mouse, PS2, optical, jack black (non-ECO)
609250-001
eSATA port assembly, PCI card (not illustrated)
645558-001
Clamp lock, includes universal cable (plate not included; not illustrated)
508987-001
Antenna for use with 538048-001 (not illustrated)
583345-001
HP Business Digital Headset (not illustrated)
642738-001
External USB webcam (not illustrated)
609252-001
Keyboard (not illustrated)
PS/2, basic
537745-xx1
USB, basic
537746-xx1
USB, mini
674314-xx1
Washable
613125-xx1
Smart card
631411-xx1
Screw Kit - misc screws
330458-001
Screw Kit - tamper resistant screws
393956-001
Small Form Factor (SFF) chassis spare parts
37
Drives
Description
Spare part number
Hard drive
1-TB, 7200-rpm
636930-001
500-GB, 7200-rpm, 2.5-inch, SED
696442-001
500-GB, 7200-rpm
636929-001
320-GB, 7200-rpm, 2.5-inch
634824-001
250-GB, 7200-rpm
636927-001
256-GB Solid-state Drive (SSD), self-encrypting (SED), SATA 6.0
680020-001
180-GB Solid-state Drive (SSD), SATA 6.0
696622-001
160-GB Solid-state Drive (SSD), SATA 3.0
646809-001
128-GB Solid-state Drive (SSD), SATA 2.0
665961-001
120-GB Solid-state Drive (SSD), SATA 2.0
661841-001
Optical drive
Blu-ray BD-Writer XL Drive
682219-001
Blu-ray BD-RW SuperMulti DL Drive
656792-001
16X SATA DVD±RW drive
660408-001
16X SATA DVD-ROM drive
581599-001
Grommet, hard drive isolation, blue
450712-001
Misc boards
38
Description
Spare part number
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
680653-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
632486-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
682411-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637213-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
637995-001
HP FireWire / IEEE 1394a PCIe x1 Card
637591-001
Intel PRO/1000CT2 NIC, includes bracket
635523-001
HP WLAN 802.11 b/g/n minicard
538048-001
Chapter 4 Illustrated parts catalog
Sequential part number listing
Spare part
number
Description
330458-001
Screw Kit
393956-001
Screw Kit - tamper resistant screws
397117-001
Hard drive conversion bracket
450712-001
Grommet, hard drive isolation, blue
463023-001
DMS-59 to dual VGA cable
487562-001
DisplayPort cable
508987-001
Clamp lock, includes universal cable (plate not included)
537745-xx1
PS/2 basic keyboard
537746-xx1
USB basic keyboard
537749-001
Mouse, USB, optical, jack black
538048-001
HP WLAN 802.11b/g/n card
570580-001
Mouse, USB, laser (non-ECO)
570838-001
Bezel blank, optical drive, 5.25-inch
581599-001
DVD-ROM drive
583345-001
Antenna for use with 538048-001
583653-001
Bezel blank, 3.5-inch
583654-001
Rubber foot
586721-001
Drive adapter, 2.5-inch
587451-001
Chassis stand
609250-001
Mouse, PS2, optical, jack black (non-ECO)
609252-001
External USB webcam
613125-xx1
Washable keyboard
613762-001
320W, 90% efficient
613763-001
320W, standard
617450-001
Adapter, DisplayPort to HDMI
619580-001
Mouse, washable
631411-xx4
Smart card keyboard
632484-001
Adapter, DisplayPort to VGA
632486-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
633756-001
SATA power extension cable
634824-001
320-GB, 7200-rpm hard drive, 2.5 inch, SED
635523-001
Intel PRO/1000CT2 NIC, includes bracket
Small Form Factor (SFF) chassis spare parts
39
40
Spare part
number
Description
636166-001
Card reader, 22-in-1
636917-001
USB powered speakers
636921-001
Fan duct
636922-001
Fan
636923-001
SATA power cable
636925-001
Speaker
636926-001
Front I/O cable and power switch assembly
636927-001
250-GB, 7200-rpm hard drive
636929-001
500-GB, 7200-rpm hard drive
636930-001
1-TB, 7200-rpm hard drive
637213-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637591-001
HP FireWire / IEEE 1394a PCIe x1 card
637995-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
638629-001
Intel Core i3 2120 (3.3-GHz, 3-MB L3 cache)
638813-001
SATA cable, 19.5 inch, 2 straight ends
638814-001
SATA cable, 25.2 inch, 1 straight end, 1 angled end
638815-001
Serial port PCI card
638816-001
Hood sensor
638817-001
Printer port, PCI card
641471-001
Solenoid lock
642738-001
HP Business Digital Headset
645326-001
Heat sink
645327-001
Chassis fan
645558-001
eSATA port assembly, PCI card
646809-001
160-GB Solid-state drive, SATA3.0
646815-001
Access panel
655973-001
Intel Pentium G850 (2.9-GHz, 3-MB L3 cache)
656792-001
Blu-ray BD-RW SuperMulti DL Drive
657239-001
System board (includes replacement thermal material)
657401-001
Adapter, DVI to VGA
660408-001
16X SATA DVD±RW drive
661841-001
120-GB Solid-state drive, SATA 2.0
662723-001
Adapter, DisplayPort to DVI
665118-001
Intel Celeron G530T (2.0-GHz, 2-MB L3 cache)
Chapter 4 Illustrated parts catalog
Spare part
number
Description
665119-001
Intel Celeron G540 (2.5-GHz, 2-MB L3 cache)
665120-001
Intel Core i3 2130 (3.4-GHz, 3-MB L3 cache)
665122-001
Intel Pentium G630 (2.7-GHz, 3-MB L3 cache)
665123-001
Intel Pentium G860 (3.0-GHz, 3-MB L3 cache)
665961-001
128-GB Solid-state drive, SATA 2.0
671612-001
Memory module, 2-GB, PC3 12800, CL11)
671613-001
Memory module, 4-GB, PC3 10600, 1333-MH
674314-xx1
Keyboard, wireless
674317-001
Mouse, wireless
674319-001
Transceiver for use with wireless mouse and keyboard
680020-001
256-GB Solid-state drive, self-encrypting (SED), SATA 6.0
680653-001
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
682219-001
Blu-ray BD-Writer XL Drive
682411-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
687943-001
Intel Core i5 3470 (3.3-GHz, 6-MB L3 cache)
687950-001
Front bezel
688162-001
Intel Core i5 3570 (3.4-GHz, 6-MB L3 cache)
688164-001
Intel Core i7 3770 (3.4-GHz, 8-MB L3 cache)
688950-001
Intel Core i3 3220 (3.3-GHz, 3-MB L3 cache, 65-W)
688951-001
Intel Core i3 3240 (3.4-GHz, 3-MB L3 cache)
689375-001
Memory module, 8-GB, PC3 12800, CL11
689578-001
Intel Core i3 3225 (3.4-GHz, 3-MB L3 cache, 55-W)
691934-001
Intel Celeron G550 (2.6-GHz, 2-MB L3 cache)
691935-001
Intel Pentium G640 (2.8-GHz, 3-MB L3 cache)
691936-001
Intel Pentium G870 (3.1-GHz, 3-MB L3 cache)
696422-001
500-GB hard drive, 7200-rpm, 2.5-inch, SED
696622-001
180-GB Solid-state drive, SATA 2.0
Small Form Factor (SFF) chassis spare parts
41
5
Routine Care, SATA Drive Guidelines,
and Disassembly Preparation
This chapter provides general service information for the computer. Adherence to the procedures and
precautions described in this chapter is essential for proper service.
CAUTION: When the computer is plugged into an AC power source, voltage is always applied to
the system board. You must disconnect the power cord from the power source before opening the
computer to prevent system board or component damage.
Electrostatic Discharge Information
A sudden discharge of static electricity from your finger or other conductor can destroy static-sensitive
devices or microcircuitry. Often the spark is neither felt nor heard, but damage occurs. An electronic
device exposed to electrostatic discharge (ESD) may not appear to be affected at all and can work
perfectly throughout a normal cycle. The device may function normally for a while, but it has been
degraded in the internal layers, reducing its life expectancy.
Networks built into many integrated circuits provide some protection, but in many cases, the
discharge contains enough power to alter device parameters or melt silicon junctions.
Generating Static
The following table shows that:
●
Different activities generate different amounts of static electricity.
●
Static electricity increases as humidity decreases.
Relative Humidity
42
Event
55%
40%
10%
Walking across carpet
7,500 V
15,000 V
35,000 V
Walking across vinyl floor
3,000 V
5,000 V
12,000 V
Motions of bench worker
400 V
800 V
6,000 V
Removing DIPs from plastic tube
400 V
700 V
2,000 V
Chapter 5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation
Removing DIPs from vinyl tray
2,000 V
4,000 V
11,500 V
Removing DIPs from Styrofoam
3,500 V
5,000 V
14,500 V
Removing bubble pack from PCB
7,000 V
20,000 V
26,500 V
Packing PCBs in foam-lined box
5,000 V
11,000 V
21,000 V
These are then multi-packaged inside plastic tubes, trays, or Styrofoam.
NOTE:
700 volts can degrade a product.
Preventing Electrostatic Damage to Equipment
Many electronic components are sensitive to ESD. Circuitry design and structure determine the
degree of sensitivity. The following packaging and grounding precautions are necessary to prevent
damage to electric components and accessories.
●
To avoid hand contact, transport products in static-safe containers such as tubes, bags, or
boxes.
●
Protect all electrostatic parts and assemblies with conductive or approved containers or
packaging.
●
Keep electrostatic sensitive parts in their containers until they arrive at static-free stations.
●
Place items on a grounded surface before removing them from their container.
●
Always be properly grounded when touching a sensitive component or assembly.
●
Avoid contact with pins, leads, or circuitry.
●
Place reusable electrostatic-sensitive parts from assemblies in protective packaging or
conductive foam.
Personal Grounding Methods and Equipment
Use the following equipment to prevent static electricity damage to equipment:
●
Wrist straps are flexible straps with a maximum of one-megohm ± 10% resistance in the ground
cords. To provide proper ground, a strap must be worn snug against bare skin. The ground cord
must be connected and fit snugly into the banana plug connector on the grounding mat or
workstation.
●
Heel straps/Toe straps/Boot straps can be used at standing workstations and are compatible
with most types of shoes or boots. On conductive floors or dissipative floor mats, use them on
both feet with a maximum of one-megohm ± 10% resistance between the operator and ground.
Static Shielding Protection Levels
Method
Voltage
Antistatic plastic
1,500
Carbon-loaded plastic
7,500
Metallized laminate
15,000
Electrostatic Discharge Information
43
Grounding the Work Area
To prevent static damage at the work area, use the following precautions:
●
Cover the work surface with approved static-dissipative material. Provide a wrist strap connected
to the work surface and properly grounded tools and equipment.
●
Use static-dissipative mats, foot straps, or air ionizers to give added protection.
●
Handle electrostatic sensitive components, parts, and assemblies by the case or PCB laminate.
Handle them only at static-free work areas.
●
Turn off power and input signals before inserting and removing connectors or test equipment.
●
Use fixtures made of static-safe materials when fixtures must directly contact dissipative
surfaces.
●
Keep work area free of nonconductive materials such as ordinary plastic assembly aids and
Styrofoam.
●
Use field service tools, such as cutters, screwdrivers, and vacuums, that are conductive.
Recommended Materials and Equipment
Materials and equipment that are recommended for use in preventing static electricity include:
44
●
Antistatic tape
●
Antistatic smocks, aprons, or sleeve protectors
●
Conductive bins and other assembly or soldering aids
●
Conductive foam
●
Conductive tabletop workstations with ground cord of one-megohm +/- 10% resistance
●
Static-dissipative table or floor mats with hard tie to ground
●
Field service kits
●
Static awareness labels
●
Wrist straps and footwear straps providing one-megohm +/- 10% resistance
●
Material handling packages
●
Conductive plastic bags
●
Conductive plastic tubes
●
Conductive tote boxes
●
Opaque shielding bags
●
Transparent metallized shielding bags
●
Transparent shielding tubes
Chapter 5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation
Operating Guidelines
To prevent overheating and to help prolong the life of the computer:
●
Keep the computer away from excessive moisture, direct sunlight, and extremes of heat and
cold.
●
Operate the computer on a sturdy, level surface. Leave a 10.2-cm (4-inch) clearance on all
vented sides of the computer and above the monitor to permit the required airflow.
●
Never restrict the airflow into the computer by blocking any vents or air intakes. Do not place the
keyboard, with the keyboard feet down, directly against the front of the desktop unit as this also
restricts airflow.
●
Occasionally clean the air vents on all vented sides of the computer. Lint, dust, and other foreign
matter can block the vents and limit the airflow. Be sure to unplug the computer before cleaning
the air vents.
●
Never operate the computer with the cover or side panel removed.
●
Do not stack computers on top of each other or place computers so near each other that they
are subject to each other’s re-circulated or preheated air.
●
If the computer is to be operated within a separate enclosure, intake and exhaust ventilation
must be provided on the enclosure, and the same operating guidelines listed above will still
apply.
●
Keep liquids away from the computer and keyboard.
●
Never cover the ventilation slots on the monitor with any type of material.
●
Install or enable power management functions of the operating system or other software,
including sleep states.
Routine Care
General Cleaning Safety Precautions
1.
Never use solvents or flammable solutions to clean the computer.
2.
Never immerse any parts in water or cleaning solutions; apply any liquids to a clean cloth and
then use the cloth on the component.
3.
Always unplug the computer when cleaning with liquids or damp cloths.
4.
Always unplug the computer before cleaning the keyboard, mouse, or air vents.
5.
Disconnect the keyboard before cleaning it.
6.
Wear safety glasses equipped with side shields when cleaning the keyboard.
Cleaning the Computer Case
Follow all safety precautions in General Cleaning Safety Precautions on page 45 before cleaning the
computer.
Operating Guidelines
45
To clean the computer case, follow the procedures described below:
●
To remove light stains or dirt, use plain water with a clean, lint-free cloth or swab.
●
For stronger stains, use a mild dishwashing liquid diluted with water. Rinse well by wiping it with
a cloth or swab dampened with clear water.
●
For stubborn stains, use isopropyl (rubbing) alcohol. No rinsing is needed as the alcohol will
evaporate quickly and not leave a residue.
●
After cleaning, always wipe the unit with a clean, lint-free cloth.
●
Occasionally clean the air vents on the computer. Lint and other foreign matter can block the
vents and limit the airflow.
Cleaning the Keyboard
Follow all safety precautions in General Cleaning Safety Precautions on page 45 before cleaning the
keyboard.
To clean the tops of the keys or the keyboard body, follow the procedures described in Cleaning the
Computer Case on page 45.
When cleaning debris from under the keys, review all rules in General Cleaning Safety Precautions
on page 45 before following these procedures:
CAUTION: Use safety glasses equipped with side shields before attempting to clean debris from
under the keys.
●
Visible debris underneath or between the keys may be removed by vacuuming or shaking.
●
Canned, pressurized air may be used to clean debris from under the keys. Caution should be
used as too much air pressure can dislodge lubricants applied under the wide keys.
●
If you remove a key, use a specially designed key puller to prevent damage to the keys. This
tool is available through many electronic supply outlets.
CAUTION: Never remove a wide leveled key (like the space bar) from the keyboard. If these
keys are improperly removed or installed, the keyboard may not function properly.
●
Cleaning under a key may be done with a swab moistened with isopropyl alcohol and squeezed
out. Be careful not to wipe away lubricants necessary for proper key functions. Use tweezers to
remove any fibers or dirt in confined areas. Allow the parts to air dry before reassembly.
Cleaning the Monitor
46
●
Wipe the monitor screen with a clean cloth moistened with water or with a towelette designed for
cleaning monitors. Do not use sprays or aerosols directly on the screen; the liquid may seep into
the housing and damage a component. Never use solvents or flammable liquids on the monitor.
●
To clean the monitor body follow the procedures in Cleaning the Computer Case on page 45.
Chapter 5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation
Cleaning the Mouse
Before cleaning the mouse, ensure that the power to the computer is turned off.
●
Clean the mouse ball by first removing the retaining plate and the ball from the housing. Pull out
any debris from the ball socket and wipe the ball with a clean, dry cloth before reassembly.
●
To clean the mouse body, follow the procedures in Cleaning the Computer Case on page 45.
Service Considerations
Listed below are some of the considerations that you should keep in mind during the disassembly and
assembly of the computer.
Power Supply Fan
The power supply fan is a variable-speed fan based on the temperature in the power supply.
CAUTION: The cooling fan is always on when the computer is in the “On” mode. The cooling fan is
off when the computer is in “Standby,” “Suspend,” or “Off” modes.
You must disconnect the power cord from the power source before opening the computer to prevent
system board or component damage.
Tools and Software Requirements
To service the computer, you need the following:
●
Torx T-15 screwdriver (HP screwdriver with bits, PN 161946-001)
●
Torx T-15 screwdriver with small diameter shank (for certain front bezel removal)
●
Flat-bladed screwdriver (may sometimes be used in place of the Torx screwdriver)
●
Phillips #2 screwdriver
●
Diagnostics software
●
HP tamper-resistant T-15 wrench (Smart Cover FailSafe Key, PN 166527-001) or HP tamperresistant bits (Smart Cover FailSafe Key, PN 166527-002)
Screws
The screws used in the computer are not interchangeable. They may have standard or metric threads
and may be of different lengths. If an incorrect screw is used during the reassembly process, it can
damage the unit. HP strongly recommends that all screws removed during disassembly be kept with
the part that was removed, then returned to their proper locations.
CAUTION: Metric screws have a black finish. U.S. screws have a silver finish and are used on hard
drives only.
CAUTION: As each subassembly is removed from the computer, it should be placed away from the
work area to prevent damage.
Service Considerations
47
Cables and Connectors
Most cables used throughout the unit are flat, flexible cables. These cables must be handled with
care to avoid damage. Apply only the tension required to seat or unseat the cables during insertion or
removal from the connector. Handle cables by the connector whenever possible. In all cases, avoid
bending or twisting the cables, and ensure that the cables are routed in such a way that they cannot
be caught or snagged by parts being removed or replaced.
CAUTION: When servicing this computer, ensure that cables are placed in their proper location
during the reassembly process. Improper cable placement can damage the computer.
Hard Drives
Handle hard drives as delicate, precision components, avoiding all physical shock and vibration. This
applies to failed drives as well as replacement spares.
●
If a drive must be mailed, place the drive in a bubble-pack mailer or other suitable protective
packaging and label the package “Fragile: Handle With Care.”
●
Do not remove hard drives from the shipping package for storage. Keep hard drives in their
protective packaging until they are actually mounted in the CPU.
●
Avoid dropping drives from any height onto any surface.
●
If you are inserting or removing a hard drive, turn off the computer. Do not remove a hard drive
while the computer is on or in standby mode.
●
Before handling a drive, ensure that you are discharged of static electricity. While handling a
drive, avoid touching the connector. For more information about preventing electrostatic
damage, refer to Electrostatic Discharge Information on page 42
●
Do not use excessive force when inserting a drive.
●
Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic
fields such as monitors or speakers.
Lithium Coin Cell Battery
The battery that comes with the computer provides power to the real-time clock and has a minimum
lifetime of about three years.
See the appropriate removal and replacement chapter for the chassis you are working on in this
guide for instructions on the replacement procedures.
WARNING! This computer contains a lithium battery. There is a risk of fire and chemical burn if the
battery is handled improperly. Do not disassemble, crush, puncture, short external contacts, dispose
in water or fire, or expose it to temperatures higher than 140ºF (60ºC). Do not attempt to recharge the
battery.
NOTE: Batteries, battery packs, and accumulators should not be disposed of together with the
general household waste. In order to forward them to recycling or proper disposal, please use the
public collection system or return them to HP, their authorized partners, or their agents.
48
Chapter 5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation
SATA Hard Drives
Serial ATA Hard Drive Characteristics
Number of pins/conductors in data cable
7/7
Number of pins in power cable
15
Maximum data cable length
39.37 in (100 cm)
Data interface voltage differential
400-700 mV
Drive voltages
3.3 V, 5 V, 12 V
Jumpers for configuring drive
N/A
Data transfer rate
3.0 Gb/s
SATA Hard Drive Cables
SATA Data Cable
Always use an HP approved SATA 3.0 Gb/s cable as it is fully backwards compatible with the SATA
1.5 Gb/s drives.
Current HP desktop products ship with SATA 3.0 Gb/s hard drives.
SATA data cables are susceptible to damage if overflexed. Never crease a SATA data cable and
never bend it tighter than a 30 mm (1.18 in) radius.
The SATA data cable is a thin, 7-pin cable designed to transmit data for only a single drive.
SMART ATA Drives
The Self Monitoring Analysis and Recording Technology (SMART) ATA drives for the HP Personal
Computers have built-in drive failure prediction that warns the user or network administrator of an
impending failure or crash of the hard drive. The SMART drive tracks fault prediction and failure
indication parameters such as reallocated sector count, spin retry count, and calibration retry count. If
the drive determines that a failure is imminent, it generates a fault alert.
Cable Management
Always follow good cable management practices when working inside the computer.
●
Keep cables away from major heat sources like the heat sink.
●
Do not jam cables on top of expansion cards or memory modules. Printed circuit cards like these
are not designed to take excessive pressure on them.
●
Keep cables clear of sliding or moveable parts to prevent them from being cut or crimped when
the parts are moved.
●
When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the
wires.
SATA Hard Drives
49
●
Some flat ribbon cables come prefolded. Never change the folds on these cables.
●
Do not bend any cable sharply. A sharp bend can break the internal wires.
●
Never bend a SATA data cable tighter than a 30 mm (1.18 in) radius.
●
Never crease a SATA data cable.
●
Do not rely on components like the drive cage, power supply, or computer cover to push cables
down into the chassis. Always position the cables to lay properly by themselves.
Hard Drive Capacities
The combination of the file system and the operating system used in the computer determines the
maximum usable size of a drive partition. A drive partition is the largest segment of a drive that may
be properly accessed by the operating system. A single hard drive may therefore be subdivided into a
number of unique drive partitions in order to make use of all of its space.
Because of the differences in the way that drive sizes are calculated, the size reported by the
operating system may differ from that marked on the hard drive or listed in the computer specification.
Drive size calculations by drive manufacturers are bytes to the base 10 while calculations by
Microsoft are bytes to the base 2.
Drive/Partition Capacity Limits
Maximum Size
50
File System
Controller Type
Operating System
Partition
Drive
FAT 32
ATA
Windows XP/Windows 7
32 GB
2 TB
NTFS
ATA
Windows XP/Windows 7
2 TB
2 TB
Chapter 5 Routine Care, SATA Drive Guidelines, and Disassembly Preparation
6
Removal and Replacement Procedures
Microtower (MT) Chassis
Adherence to the procedures and precautions described in this chapter is essential for proper service.
After completing all necessary removal and replacement procedures, run the Diagnostics utility to
verify that all components operate properly.
NOTE:
Not all features listed in this guide are available on all computers.
Preparation for Disassembly
See Routine Care, SATA Drive Guidelines, and Disassembly Preparation on page 42 for initial safety
procedures.
1.
Remove/disengage any security devices that prohibit opening the computer.
2.
Close any open software applications.
3.
Exit the operating system.
4.
Remove any diskette, compact disc, or media card from the computer.
5.
Turn off the computer and any peripheral devices that are connected to it.
CAUTION: Turn off the computer before disconnecting any cables.
Regardless of the power-on state, voltage is always present on the system board as long as the
system is plugged into an active AC outlet. In some systems the cooling fan is on even when the
computer is in the “Standby,” or “Suspend” modes. The power cord should always be
disconnected before servicing a unit.
6.
Disconnect the power cord from the electrical outlet and then from the computer.
7.
Disconnect all peripheral device cables from the computer.
8.
As applicable, lay the computer down on its side to achieve a safe working position.
NOTE: During disassembly, label each cable as you remove it, noting its position and routing.
Keep all screws with the units removed.
CAUTION: The screws used in the computer are of different thread sizes and lengths; using the
wrong screw in an application may damage the unit.
Preparation for Disassembly
51
Computer Access Panel
Description
Spare part number
Access panel
646825-001
To access internal components, you must remove the access panel:
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Loosen the two captive thumbscrews (1) that secure the access panel to the computer chassis.
3.
Use the handle located between the thumbscrews to lift the access panel off the unit (2).
NOTE: You may want to lay the computer on its side to install internal parts. Be sure the side
with the access panel is facing up.
Figure 6-1 Removing the Computer Access Panel
52
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
Front Bezel
Description
Spare part number
Front bezel for use in all countries and regions except China
689377-001
Front bezel for use in China
689378-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
3.
Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2).
Figure 6-2 Removing the Front Bezel
Front Bezel
53
Front Bezel Security
The front bezel can be locked in place by installing a security screw provided by HP. To install the
security screw:
1.
Remove/disengage any security devices that prohibit opening the computer.
2.
Remove all removable media, such as compact discs or USB flash drives, from the computer.
3.
Turn off the computer properly through the operating system, then turn off any external devices.
4.
Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board
as long as the system is plugged into an active AC outlet. You must disconnect the power cord
to avoid damage to the internal components of the computer.
5.
Remove the access panel and front bezel.
6.
Remove the security screw from the inside of the front bezel.
Figure 6-3 Retrieving the Front Bezel Security Screw
7.
54
Replace the front bezel.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
8.
Install the screw through the interior of the front of the chassis into the front bezel. The screw
hole is located toward the middle of the right edge of the chassis between the hard drive bay and
speaker.
Figure 6-4 Installing the Front Bezel Security Screw
9.
Replace the access panel.
10. Reconnect the power cord and turn on the computer.
11. Lock any security devices that were disengaged when the access panel was removed.
Front Bezel Security
55
Bezel Blanks
Description
Spare part number
3.5-inch bezel blank
583653-001
5.25-inch bezel blank, optical drive
570838-001
On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch drive bays that need to
be removed before installing a drive. To remove a bezel blank:
1.
Remove the access panel (Computer Access Panel on page 52)
2.
Remove the front bezel (Front Bezel on page 53)
3.
To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards
the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it
(2).
Figure 6-5 Removing a Bezel Blank
56
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
Memory
Description
Spare part number
8-GB, PC3-12800
689375-001
4-GB, PC3-12800
671613-001
2-GB, PC3-12800
671612-001
The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs).
DIMMs
The memory sockets on the system board can be populated with up to four industry-standard DIMMs.
These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum
memory support, you can populate the system board with up to 16-GB of memory configured in a
high-performing dual channel mode.
DDR3-SDRAM DIMMs
CAUTION: This product DOES NOT support DDR3 Ultra Low Voltage (DDR3U) memory. The
processor is not compatible with DDR3U memory and if you plug DDR3U memory into the system
board, it can cause the physical damage to the DIMM or invoke system malfunction.
For proper system operation, the DDR3-SDRAM DIMMs must be:
●
industry-standard 240-pin
●
unbuffered non-ECC PC3-12800 DDR3-1600 MHz-compliant
●
1.5 volt DDR3-SDRAM DIMMs
The DDR3-SDRAM DIMMs must also:
●
support CAS latency 11 DDR3 1600 MHz (11-11-11 timing)
●
contain the mandatory JEDEC SPD information
In addition, the computer supports:
●
512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies
●
single-sided and double-sided DIMMs
●
DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not
supported
NOTE:
The system will not operate properly if you install unsupported DIMMs.
Populating DIMM Sockets
There are four DIMM sockets on the system board, with two sockets per channel. The sockets are
labeled DIMM1, DIMM2, DIMM3, and DIMM4. Sockets DIMM1 and DIMM2 operate in memory
channel B. Sockets DIMM3 and DIMM4 operate in memory channel A.
Memory
57
The system will automatically operate in single channel mode, dual channel mode, or flex mode,
depending on how the DIMMs are installed.
●
The system will operate in single channel mode if the DIMM sockets are populated in one
channel only.
●
The system will operate in a higher-performing dual channel mode if the total memory capacity
of the DIMMs in Channel A is equal to the total memory capacity of the DIMMs in Channel B.
The technology and device width can vary between the channels. For example, if Channel A is
populated with two 1-GB DIMMs and Channel B is populated with one 2-GB DIMM, the system
will operate in dual channel mode.
●
The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is
not equal to the total memory capacity of the DIMMs in Channel B. In flex mode, the channel
populated with the least amount of memory describes the total amount of memory assigned to
dual channel and the remainder is assigned to single channel. For optimal speed, the channels
should be balanced so that the largest amount of memory is spread between the two channels.
If one channel will have more memory than the other, the larger amount should be assigned to
Channel A. For example, if you are populating the sockets with one 2-GB DIMM, and three 1-GB
DIMMs, Channel A should be populated with the 2-GB DIMM and one 1-GB DIMM, and Channel
B should be populated with the other two 1-GB DIMMs. With this configuration, 4-GB will run as
dual channel and 1-GB will run as single channel.
●
In any mode, the maximum operational speed is determined by the slowest DIMM in the system.
Installing DIMMs
CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power
to drain before adding or removing memory modules. Regardless of the power-on state, voltage is
always supplied to the memory modules as long as the computer is plugged into an active AC outlet.
Adding or removing memory modules while voltage is present may cause irreparable damage to the
memory modules or system board.
The memory module sockets have gold-plated metal contacts. When upgrading the memory, it is
important to use memory modules with gold-plated metal contacts to prevent corrosion and/or
oxidation resulting from having incompatible metals in contact with each other.
Static electricity can damage the electronic components of the computer or optional cards. Before
beginning these procedures, ensure that you are discharged of static electricity by briefly touching a
grounded metal object. For more information, refer to Electrostatic Discharge Information on page 42.
When handling a memory module, be careful not to touch any of the contacts. Doing so may damage
the module.
58
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
3.
Open both latches of the memory module socket (1), and insert the memory module into the
socket (2).
Figure 6-6 Installing a DIMM
NOTE: A memory module can be installed in only one way. Match the notch on the module
with the tab on the memory socket.
Populate the black DIMM sockets before the white DIMM sockets.
For maximum performance, populate the sockets so that the memory capacity is spread as
equally as possible between Channel A and Channel B. Refer to Populating DIMM Sockets
on page 57 for more information.
4.
Push the module down into the socket, ensuring that the module is fully inserted and properly
seated. Make sure the latches are in the closed position (3).
5.
Repeat steps 3 and 4 to install any additional modules.
6.
Replace the computer access panel.
7.
Reconnect the power cord and turn on the computer.
8.
Lock any security devices that were disengaged when the access panel was removed.
The computer should automatically recognize the additional memory the next time you turn on the
computer.
Memory
59
Expansion Cards
Description
Spare part number
GeForce GT630 PCIe x16 graphics card, 2 GB
684591-001
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
680653-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
632486-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
682411-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
637995-001
Intel PRO/1000CT2 NIC, includes bracket
635523-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637213-001
HP FireWire / IEEE 1394a PCIe x1 Card
637591-001
The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI
Express x16 expansion slot.
NOTE:
You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 slot.
To remove, replace, or add an expansion card:
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
3.
Locate the correct vacant expansion socket on the system board and the corresponding
expansion slot on the back of the computer chassis.
4.
Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on
the latch and rotating the latch to the open position.
Figure 6-7 Opening the Expansion Slot Retainer
60
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
5.
Before installing an expansion card, remove the expansion slot cover or the existing expansion
card.
NOTE: Before removing an installed expansion card, disconnect any cables that may be
attached to the expansion card.
a.
If you are installing an expansion card in a vacant socket, remove the appropriate
expansion slot cover on the back of the chassis. Pull the slot cover straight up then away
from the inside of the chassis.
Figure 6-8 Removing an Expansion Slot Cover
Expansion Cards
61
b.
If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end,
and carefully rock it back and forth until the connectors pull free from the socket. Pull the
expansion card straight up from the socket then away from the inside of the chassis to
release it from the chassis frame. Be sure not to scrape the card against the other
components.
Figure 6-9 Removing a Standard PCI Expansion Card
c.
If you are removing a PCI Express x16 card, pull the retention arm on the back of the
expansion socket away from the card and carefully rock the card back and forth until the
connectors pull free from the socket. Pull the expansion card straight up from the socket
then away from the inside of the chassis to release it from the chassis frame. Be sure not to
scrape the card against the other components.
Figure 6-10 Removing a PCI Express x16 Expansion Card
6.
62
Store the removed card in anti-static packaging.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
7.
If you are not installing a new expansion card, install an expansion slot cover to close the open
slot.
CAUTION: After removing an expansion card, you must replace it with a new card or
expansion slot cover for proper cooling of internal components during operation.
8.
To install a new expansion card, hold the card just above the expansion socket on the system
board then move the card toward the rear of the chassis so that the bracket on the card is
aligned with the open slot on the rear of the chassis. Press the card straight down into the
expansion socket on the system board.
Figure 6-11 Installing an Expansion Card
NOTE: When installing an expansion card, press firmly on the card so that the whole
connector seats properly in the expansion card slot.
9.
Rotate the slot cover retention latch back in place to secure the expansion card.
10. Connect external cables to the installed card, if needed. Connect internal cables to the system
board, if needed.
11. Replace the computer access panel.
12. Reconnect the power cord and turn on the computer.
13. Lock any security devices that were disengaged when the access panel was removed.
14. Reconfigure the computer, if necessary.
Expansion Cards
63
System Board Connections
Refer to the following illustrations and tables to identify the system board connectors for your model.
Figure 6-12 System Board Connections
Table 6-1 System Board Connections
64
No.
System Board Connector
System Board Label
Color
Component
1
DIMM4 (Channel A)
DIMM4
white
Memory Module
2
DIMM3 (Channel A)
DIMM3
black
Memory Module
3
DIMM2 (Channel B)
DIMM2
white
Memory Module
4
DIMM1 (Channel B)
DIMM1
black
Memory Module
5
Power
SATAPWR1
black
SATA Optical Drives
6
Power
SATAPWR0
black
SATA Hard Drives
7
SATA 3.0
SATA0
dark blue
1st Hard Drive
8
SATA 2.0
SATA1
white
2nd Hard Drive, or 2nd Optical Drive
if an eSATA Adapter Cable exists
9
SATA 2.0
SATA2
white
1st Optical Drive
10
eSATA
ESATA
black
eSATA Adapter Cable, or 2nd
Optical Drive
11
Parallel Port
PAR
black
Parallel Port
12
Serial Port
COMB
black
Serial Port
13
USB
MEDIA
black
USB Device, such as a Media Card
Reader
14
Hood Lock
HLCK
black
Hood Lock
16
Hood Sensor
HSENSE
white
Hood Sensor
15
USB
MEDIA2
black
USB Device, such as a Media Card
Reader
17
PCI Express x1
X1PCIEXP1
black
Expansion Card
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
Table 6-1 System Board Connections (continued)
No.
System Board Connector
System Board Label
Color
Component
18
PCI Express x1
X1PCIEXP2
black
Expansion Card
19
PCI Express x16
X16PCIEXP
black
Expansion Card
20
PCI
PCI1
white
Expansion Card
System Board Connections
65
Drives
Description
Spare part number
DVD±RW drive
660408-001
DVD-ROM drive
581599-001
Blu-ray BD-Writer XL Drive
682219-001
Blu-ray BD-RW SuperMulti DL Drive
656792-001
1 TB, 7200 rpm SATA hard drive
636930-001
500 GB, 7200 rpm, 2.5 inch, SED, SATA hard drive
696422-001
500 GB, 7200 rpm SATA hard drive
636929-001
320 GB, 7200 rpm SATA hard drive, 2.5-inch
634824-001
250 GB, 7200 rpm SATA hard drive
636927-001
256 GB Solid State Drive (SSD), self-encrypting (SED), SATA 6.0
680020-001
180 GB Solid State Drive (SSD), SATA 6.0
696622-001
160 GB Solid State Drive (SSD), SATA 3.0
646809-001
128 GB Solid State Drive (SSD), SATA 2.0
665961-001
120 GB Solid State Drive (SSD), SATA 2.0
661841-001
When installing drives, follow these guidelines:
66
●
The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA
connector on the system board labeled SATA0. If you are adding a second hard drive, connect it
to the white connector on the system board labeled SATA1.
●
Connect the first SATA optical drive to the white SATA connector on the system board labeled
SATA2. If you are adding a second optical drive connect it to the black SATA connector on the
system board labeled ESATA. If the ESATA connector is already populated, connect the second
optical drive to the white connector labeled SATA1.
●
Connect an optional eSATA adapter cable to the black SATA connector on the system board
labeled ESATA.
●
Connect a media card reader USB cable to the USB connector on the system board labeled
MEDIA.
●
The power cable for the SATA optical drives is a two-headed cable this is plugged into the
system board with the first connector routed to the top 5.25-inch bay and the second connector
routed to the bottom 5.25-inch bay.
●
The power cable for the SATA hard drives is a two-headed cable this is plugged into the system
board with the first connector routed to the bottom 3.5-inch bay and the second connector routed
to the top 3.5-inch bay.
●
The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.
●
You must install guide screws to ensure the drive will line up correctly in the drive cage and lock
in place. HP has provided extra guide screws for the drive bays (four 6-32 isolation mounting
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
guide screws and eight M3 metric guide screws), installed on the side of the drive bays. The
6-32 isolation mounting screws are required for a secondary hard drive. All other drives (except
the primary hard drive) use M3 metric screws. The HP-supplied metric screws are black and the
HP-supplied isolation mounting screws are silver and blue. If you are replacing the primary hard
drive, you must remove the four silver and blue 6-32 isolation mounting guide screws from the
old hard drive and install them in the new hard drive.
Figure 6-13 Extra Guide Screw Locations
No.
Guide Screw
Device
1
Black M3 Metric Screws
All Drives (except hard drives)
2
Silver and Blue 6-32 Isolation Mounting Screws
Secondary Hard Drive
CAUTION: To prevent loss of work and damage to the computer or drive:
If you are inserting or removing a drive, shut down the operating system properly, turn off the
computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby
mode.
Before handling a drive, ensure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Handle a drive carefully; do not drop it.
Do not use excessive force when inserting a drive.
Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields
such as monitors or speakers.
If a drive must be mailed, place the drive in a bubble-pack mailer or other protective packaging and
label the package “Fragile: Handle With Care.”
Drives
67
Drive Positions
Figure 6-14 Drive Positions
Table 6-2 Drive Positions
1
Two 5.25-inch drive bays for optional drives (optical drives shown)
2
One 3.5-inch drive bay for optional drive (media card reader shown)
3
Secondary 3.5-inch internal hard drive bay for optional hard drive
4
Primary 3.5-inch internal hard drive bay
NOTE: The drive configuration on your computer may be different than the drive
configuration shown above.
To verify the type and size of the storage devices installed in the computer, run Computer Setup.
Removing a 5.25-inch or 3.5-inch Drive from a Drive Bay
CAUTION: All removable media should be taken out of a drive before removing the drive from the
computer.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
3.
Remove the front bezel (Front Bezel on page 53)
4.
Disconnect the drive cables, as indicated in the following illustrations.
CAUTION: When removing the cables, pull the tab or connector instead of the cable itself to
avoid damaging the cable.
a.
68
If you are removing an optical drive, disconnect the power cable and data cable from the
back of the drive.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
b.
If you are removing a media card reader, disconnect the USB cable from the system board.
Figure 6-15 Disconnecting the Media Card Reader USB Cable
5.
A latch drive bracket with release tabs secures the drives in the drive bay. Lift the release tab on
the latch drive bracket (1) for the drive you want to remove, then slide the drive from its drive bay
(2).
Figure 6-16 Removing the Drives
Installing a 5.25-inch or 3.5-inch Drive into a Drive Bay
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
Drives
69
3.
Remove the front bezel (Front Bezel on page 53)
4.
If you are installing a drive in a bay covered by a bezel blank, remove the bezel blank. See Bezel
Blanks on page 56 for more information.
5.
Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided
eight extra M3 metric guide screws on the front of the chassis, under the front bezel. The M3
metric guide screws are black. Refer to Drives on page 66 for an illustration of the extra M3
metric guide screws location.
NOTE: When replacing the drive, transfer the four M3 metric guide screws from the old drive to
the new one.
CAUTION: Use only 5-mm long screws as guide screws. Longer screws can damage the
internal components of the drive.
Figure 6-17 Installing Guide Screws (Optical Drive Shown)
6.
Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until
the drive snaps into place.
Figure 6-18 Sliding the Drives into the Drive Cage
7.
Connect the power and data cables to the drive as indicated in the following illustrations.
a.
If you are installing an optical drive, connect the power cable and data cable to the back of
the drive.
NOTE: The power cable for the optical drives is a two-headed cable that is routed from
the system board to the rear of the optical drive bays.
70
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
b.
If your are installing a media card reader, connect the USB cable to the USB system board
connector labeled MEDIA.
Figure 6-19 Connecting the Media Card Reader USB Cable
8.
If installing a new drive, connect the opposite end of the data cable to the appropriate system
board connector.
NOTE: If you are installing a new SATA optical drive, connect the data cable for the first optical
drive to the white SATA connector on the system board labeled SATA2. Connect the data cable
for a second optical drive to the black SATA connector on the system board labeled ESATA. If
the ESATA connector is already populated, connect the second optical drive to white connector
labeled SATA1.
Refer to System Board Connections on page 64 for an illustration of the system board drive
connectors.
9.
Replace the front bezel and computer access panel.
10. Reconnect the power cord and any external devices, then turn on the computer.
11. Lock any security devices that were disengaged when the access panel was removed.
Drives
71
Removing a Hard Drive from a Drive Bay
NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so
that you can transfer the data to the new hard drive.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
3.
Disconnect the power cable and data cable from the back of the hard drive.
4.
Release the drive by pulling the release tab away from the drive (1) and sliding the drive out of
the bay (2).
Figure 6-20 Removing a Hard Drive
5.
Remove the four guide screws (two on each side) from the old drive. You will need these screws
to install a new drive.
Installing a Hard Drive into an Internal Drive Bay
NOTE:
72
The system does not support Parallel ATA (PATA) hard drives.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51)
2.
Remove the access panel (Computer Access Panel on page 52)
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
3.
Install guide screws on the sides of the drive. If you are installing a 2.5-inch drive, you must
install the drive in an adapter bracket.
NOTE: The hard drive uses 6-32 isolation mounting guide screws. Four extra guide screws are
installed on the exterior of the hard drive bays. The HP-supplied isolation mounting guide screws
are silver and blue. Refer to Drives on page 66 for an illustration of the extra 6-32 isolation
mounting guide screws location.
If you are replacing a drive, transfer the guides screws from the old drive to the new one.
●
If you are installing a 3.5-inch hard drive, install four isolation mounting guide screws (two
on each side of the drive).
Figure 6-21 Installing Isolation Mounting Guide Screws in a 3.5-inch Drive
●
If you are installing a 2.5-inch hard drive:
◦
Slide the drive into the bay adapter bracket, ensuring the connector on the drive is fully
inserted into the connector on the adapter bracket.
Figure 6-22 Sliding the 2.5-inch Drive in the Adapter Bracket
Drives
73
◦
Secure the drive to the bay adapter bracket by installing four black M3 adapter bracket
screws through the sides of the bracket into the drive.
Figure 6-23 Securing the Drive in the Adapter Bracket
◦
Install four 6-32 silver and blue isolation mounting guide screws in the adapter bracket
(two on each side of the bracket).
Figure 6-24 Installing Isolation Mounting Guide Screws in the Adapter Bracket
74
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
4.
Slide the drive into the drive bay, making sure to align the guide screws with the guide slots, until
the drive snaps into place. The bottom bay is for the primary hard drive. The upper bay is for an
optional secondary hard drive.
Figure 6-25 Sliding a Hard Drive into the Drive Bay
5.
Connect the power cable and data cable to the back of the hard drive.
NOTE: The power cable for the hard drives is a two-headed cable that is routed from the
system board to the rear of the hard drive bays.
6.
If installing a new drive, connect the opposite end of the data cable to the appropriate system
board connector.
NOTE: If your system has only one SATA hard drive, you must connect the hard drive data
cable to the dark blue connector labeled SATA0 to avoid any hard drive performance problems.
If you are adding a second hard drive, connect the data cable to the white connector labeled
SATA1.
7.
Route the power and data cables in their cable retainers.
8.
Replace the computer access panel.
9.
Reconnect the power cord and any external devices, then turn on the computer.
10. Lock any security devices that were disengaged when the access panel was removed.
Drives
75
Front Fan Assembly
Description
Spare part number
Front fan assembly
585884-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the cables from the clip on the top of the fan assembly.
Figure 6-26 Removing the cables from atop the front fan assembly
4.
76
Unplug the fan cable from the system board connector labeled CHFAN.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
5.
Press the lever that secures the assembly to the chassis (1), pivot the assembly forward toward
the front of the computer (2), and then lift the assembly straight up and out of the computer (3).
Figure 6-27 Removing the front fan assembly
To reinstall the front fan, reverse the removal procedure.
Front Fan Assembly
77
Front I/O Assembly
Description
Spare part number
Front I/O assembly
646827-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the computer access panel (Computer Access Panel on page 52).
3.
Remove the front bezel (Front Bezel on page 53).
4.
Remove the front fan (Front Fan Assembly on page 76).
5.
Disconnect the three front I/O cables (yellow, green, and blue) from the system board
connectors (FRONT USB, FRONT USB2, and FRONT AUD).
6.
Remove the Torx T15 screw that secures the assembly to the chassis.
Figure 6-28 Removing the front I/O assembly screw
7.
Rotate the left side of the assembly to the right .
Figure 6-29 Removing the front I/O assembly
8.
Pull the assembly away from the computer while threading the wires through the hole in the front
of the chassis.
To reinstall the assembly, reverse the removal procedure.
78
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
Power Switch/LED Assembly
Description
Spare part number
Power switch/LED assembly
646828-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the front bezel (Front Bezel on page 53).
4.
Remove the front fan (Front Fan Assembly on page 76).
5.
Disconnect the cable from the system board connector labeled PB/LED.
6.
With the computer on its side, press on the tabs on the bottom of the assembly (1) to disengage
the assembly from the chassis, and then rotate the bottom of the assembly upward (2) to
remove it from the chassis.
Figure 6-30 Removing the power switch/LED
7.
Pull the assembly away from the chassis while threading the cable through the hole in front of
the chassis.
Power Switch/LED Assembly
79
Heat sink
Description
Spare part number
Heat sink
645326-001
WARNING! To reduce risk of personal injury from hot surfaces, allow the internal system
components to cool before touching.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the computer access panel (Computer Access Panel on page 52).
3.
Remove the front fan (Front Fan Assembly on page 76).
4.
Loosen the four silver captive Torx T15 screws that secure the heat sink to the system board.
CAUTION: Remove heat sink retaining screws in diagonally opposite pairs (as in an X) to even
the downward forces on the processor. The pins on the socket are very fragile and any damage
to them may require replacing the system board.
80
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
5.
Lift the heat sink from atop the processor.
When reinstalling the heat sink, make sure that its bottom has been cleaned with an alcohol wipe and
fresh thermal grease has been applied to the top of the processor.
CAUTION: Heat sink retaining screws should be tightened in diagonally opposite pairs (as in an X)
to evenly seat the heat sink on the processor. This is especially important as the pins on the socket
are very fragile and any damage to them may require replacing the system board.
Heat sink
81
Processor
Description
Spare part number
Intel Core i7 processor
3770, 3.4 GHz, 8-MB L3 cache, 95W
688164-001
Intel Core i5 processors
3570, 3.4 GHz, 6-MB L3 cache, 95W
688162-001
3470, 3.2 GHz, 6-MB L3 cache, 95W
687943-001
Intel Core i3 processors
3240, 3.4 GHz, 3-MB L3 cache
688951-001
3225, 3.3 GHz, 3-MB L3 cache, 55W
689578-001
3220, 3.3 GHz, 3-MB L3 cache, 65W
688950-001
2130, 3.4 GHz, 3-MB L3 cache
665120-001
2120, 3.3 GHz, 3-MB L3 cache
638629-001
Intel Pentium processors
G870, 3.1 GHz, 3-MB L3 cache
G860, 3.0 GHz, 3-MB L3 cache
691936-001
G850, 2.9 GHz, 3-MB L3 cache
655973-001
G640, 2.8 GHz, 3-MB L3 cache
691935-001
G630, 2.7 GHz, 3-MB L3 cache
665122-001
Intel Celeron processors
82
G550, 2.6 GHz, 2-MB L3 cache
691934-001
G540, 2.5 GHz, 2-MB L3 cache
665119-001
G530T, 2.0 GHz, 2-MB L3 cache
665118-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the heat sink (Heat sink on page 80).
4.
Rotate the locking lever to its full open position (1).
5.
Raise and rotate the microprocessor retainer to its fully open position (2).
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
6.
Carefully lift the processor from the socket (3).
CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and
handling them could cause irreparable damage. Once pins are damaged it may be necessary to
replace the system board.
The heat sink must be installed within 24 hours of installing the processor to prevent damage to
the processor’s solder connections.
Processor
83
To install a new processor:
1.
Place the processor in its socket and close the retainer.
2.
Secure the locking lever.
If reusing the existing heat sink, go to step 3.
If using a new heat sink, go to step 5.
3.
If reusing the existing heat sink, apply the thermal grease provided in the spares kit to the top of
the processor.
4.
Clean the bottom of the heat sink with the provided alcohol pad and place it atop the processor.
5.
If using a new heat sink, remove the protective covering from the bottom of the heat sink and
place it in position atop the processor.
6.
Secure the heat sink to the system board and system board tray with the four captive screws
and attach the heat sink control cable to the system board.
CAUTION: Heat sink retaining screws should be tightened in diagonally opposite pairs (as in
an X) to evenly seat the heat sink on the processor. This is especially important as the pins on
the socket are very fragile and any damage to them may require replacing the system board.
NOTE: After installing a new processor onto the system board, always update the system ROM to
ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can
be found on the Web at: http://h18000.www1.hp.com/support/files.
84
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
Speaker
Description
Spare part number
Speaker
645330-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the front fan assembly (Front Fan Assembly on page 76).
4.
Disconnect the speaker wire from the system board connector labeled SPKR.
5.
From the inside of the chassis, remove the two silver Torx T15 screws (1) that secure the
speaker to the chassis.
6.
Rotate the top of the speaker downward (2), and then remove it from the chassis.
Figure 6-31 Removing the speaker
To replace the speaker, reverse the removal procedures.
Speaker
85
Rear Chassis Fan
Description
Spare part number
Rear chassis fan
636922-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the four silver Phillips screws that secure the fan to the chassis.
Figure 6-32 Rear fan screws
4.
86
Disconnect the fan control cable (1) from the system board connector labeled CHFAN2.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
5.
Lift the fan out of the chassis (2).
Figure 6-33 Removing the rear fan
To install the fan assembly, reverse the removal procedure. Be sure to orient the air flow out of the
unit.
Rear Chassis Fan
87
Power Supply
Description
Spare part number
Power supply, 320W, 90% efficient
613764-001
Power supply, 320W
613765-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Disconnect the power cables from the white system board connector labeled PWR and the white
system board connector labeled PWRCMD.
4.
Remove the power cables from the clip on the base pan.
5.
Remove the four silver Torx T15 screws that connect the power supply to the chassis.
Figure 6-34 Power supply screws
6.
88
Press the tab (1) on the base pan in front of the power supply that holds it in place.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
7.
Slide the power supply toward the front of the computer (2), rotate toward the fan so the power
supply clears the lip on the top of the chassis, and then lift the power supply out of the chassis
(3).
Figure 6-35 Removing the power supply
To install the power supply, reverse the removal procedure.
Power Supply
89
System Board
Description
Spare part number
System board (includes thermal material)
657239-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 51).
2.
Remove the access panel (Computer Access Panel on page 52).
3.
Remove the front fan assembly (Front Fan Assembly on page 76).
4.
When replacing the system board, make sure the following components are removed from the
defective system board and installed on the replacement system board:
●
Memory modules (Memory on page 57)
●
Expansion cards (Expansion Cards on page 60)
●
Heat sink (Heat sink on page 80).
●
Processor (Processor on page 82)
5.
Disconnect all cables connected to the system board, noting their location for reinstallation.
6.
Remove the eight Torx T15 screws that secure the system board to the chassis.
Figure 6-36 System board screws
7.
Slide the system board toward the front of the computer to disengage the I/O panel, lift the rear
of the system board up at an angle, and then lift the system board out of the computer.
When reinstalling the system board, first insert the I/O panel back into the slots in the rear of the
chassis, and then align the board with the chassis screw holes.
NOTE:
90
When replacing the system board, you must change the chassis serial number in the BIOS.
Chapter 6 Removal and Replacement Procedures Microtower (MT) Chassis
7
Removal and Replacement Procedures
Small Form Factor (SFF) Chassis
Adherence to the procedures and precautions described in this chapter is essential for proper service.
After completing all necessary removal and replacement procedures, run the Diagnostics utility to
verify that all components operate properly.
NOTE:
Not all features listed in this guide are available on all computers.
Preparation for Disassembly
See Routine Care, SATA Drive Guidelines, and Disassembly Preparation on page 42 for initial safety
procedures.
1.
Remove/disengage any security devices that prohibit opening the computer.
2.
Close any open software applications.
3.
Exit the operating system.
4.
Remove any compact disc or media card from the computer.
5.
Turn off the computer and any peripheral devices that are connected to it.
CAUTION: Turn off the computer before disconnecting any cables.
Regardless of the power-on state, voltage is always present on the system board as long as the
system is plugged into an active AC outlet. In some systems the cooling fan is on even when the
computer is in the “Standby,” or “Suspend” modes. The power cord should always be
disconnected before servicing a unit.
6.
Disconnect the power cord from the electrical outlet and then from the computer.
7.
Disconnect all peripheral device cables from the computer.
NOTE: During disassembly, label each cable as you remove it, noting its position and routing.
Keep all screws with the units removed.
CAUTION: The screws used in the computer are of different thread sizes and lengths; using
the wrong screw in an application may damage the unit.
Preparation for Disassembly
91
Access Panel
Description
Spare part number
Access panel
646815-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
If the computer is on a stand, remove the computer from the stand.
3.
Lift up on the access panel handle (1) then lift the access panel off the computer (2).
Figure 7-1 Removing the access panel
To install the access panel, reverse the removal procedure.
92
Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Front Bezel
Description
Spare part number
Front bezel
687950-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Lift up the three tabs on the side of the bezel (1), then rotate the bezel off the chassis (2).
Figure 7-2 Removing the front bezel
To install the front bezel, reverse the removal procedure.
Front Bezel
93
Front Bezel Security
The front bezel can be locked in place by installing a security screw provided by HP. To install the
security screw:
1.
Remove/disengage any security devices that prohibit opening the computer.
2.
Remove all removable media, such as compact discs or USB flash drives, from the computer.
3.
Turn off the computer properly through the operating system, then turn off any external devices.
4.
Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board
as long as the system is plugged into an active AC outlet. You must disconnect the power cord
to avoid damage to the internal components of the computer.
5.
If the computer is on a stand, remove the computer from the stand.
6.
Remove the access panel and front bezel.
7.
Remove one of the five silver 6-32 standard screws located on the front of the chassis behind
the bezel.
Figure 7-3 Retrieving the Front Bezel Security Screw
8.
94
Replace the front bezel.
Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
9.
Install the security screw next to the middle front bezel release tab to secure the front bezel in
place.
Figure 7-4 Installing the Front Bezel Security Screw
10. Replace the access panel.
11. If the computer was on a stand, replace the stand.
12. Reconnect the power cord and turn on the computer.
13. Lock any security devices that were disengaged when the access panel was removed.
Front Bezel Security
95
Bezel Blanks
Description
Spare part number
3.5-inch bezel blank
583653-001
5.25-inch bezel blank, optical drive
570838-001
On some models, there are bezel blanks covering the 3.5-inch and 5.25-inch external drive bays that
need to be removed before installing a drive. To remove a bezel blank:
1.
Remove the access panel (Access Panel on page 92).
2.
Remove the front bezel (Front Bezel on page 93)..
3.
To remove a bezel blank, push the two retaining tabs that hold the bezel blank in place towards
the outer right edge of the bezel (1) and slide the bezel blank back and to the right to remove it
(2).
Figure 7-5 Removing a bezel blank
4.
96
Replace the front bezel.
Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Memory
Description
Spare part number
8-GB, PC3-12800
689375-001
4-GB, PC3-12800
671613-001
2-GB, PC3-12800
671612-001
The computer comes with double data rate 3 synchronous dynamic random access memory (DDR3SDRAM) dual inline memory modules (DIMMs).
DIMMs
The memory sockets on the system board can be populated with up to four industry-standard DIMMs.
These memory sockets are populated with at least one preinstalled DIMM. To achieve the maximum
memory support, you can populate the system board with up to 16-GB of memory configured in a
high-performing dual channel mode.
DDR3-SDRAM DIMMs
CAUTION: This product DOES NOT support DDR3 Ultra Low Voltage (DDR3U) memory. The
processor is not compatible with DDR3U memory and if you plug DDR3U memory into the system
board, it can cause the physical damage to the DIMM or invoke system malfunction.
For proper system operation, the DDR3-SDRAM DIMMs must be:
●
industry-standard 240-pin
●
unbuffered non-ECC PC3-12800 DDR3-1600 MHz-compliant
●
1.5 volt DDR3-SDRAM DIMMs
The DDR3-SDRAM DIMMs must also:
●
support CAS latency 11 DDR3 1600 MHz (11-11-11 timing)
●
contain the mandatory JEDEC SPD information
In addition, the computer supports:
●
512-Mbit, 1-Gbit, and 2-Gbit non-ECC memory technologies
●
single-sided and double-sided DIMMs
●
DIMMs constructed with x8 and x16 DDR devices; DIMMs constructed with x4 SDRAM are not
supported
NOTE:
The system will not operate properly if you install unsupported DIMMs.
Populating DIMM Sockets
There are four DIMM sockets on the system board, with two sockets per channel. The sockets are
labeled DIMM1, DIMM2, DIMM3, and DIMM4. Sockets DIMM1 and DIMM2 operate in memory
channel B. Sockets DIMM3 and DIMM4 operate in memory channel A.
Memory
97
The system will automatically operate in single channel mode, dual channel mode, or flex mode,
depending on how the DIMMs are installed.
●
The system will operate in single channel mode if the DIMM sockets are populated in one
channel only.
●
The system will operate in a higher-performing dual channel mode if the total memory capacity
of the DIMMs in Channel A is equal to the total memory capacity of the DIMMs in Channel B.
The technology and device width can vary between the channels. For example, if Channel A is
populated with two 1-GB DIMMs and Channel B is populated with one 2-GB DIMM, the system
will operate in dual channel mode.
●
The system will operate in flex mode if the total memory capacity of the DIMMs in Channel A is
not equal to the total memory capacity of the DIMMs in Channel B. In flex mode, the channel
populated with the least amount of memory describes the total amount of memory assigned to
dual channel and the remainder is assigned to single channel. For optimal speed, the channels
should be balanced so that the largest amount of memory is spread between the two channels.
If one channel will have more memory than the other, the larger amount should be assigned to
Channel A. For example, if you are populating the sockets with one 2-GB DIMM, and three 1-GB
DIMMs, Channel A should be populated with the 2-GB DIMM and one 1-GB DIMM, and Channel
B should be populated with the other two 1-GB DIMMs. With this configuration, 4-GB will run as
dual channel and 1-GB will run as single channel.
●
In any mode, the maximum operational speed is determined by the slowest DIMM in the system.
Installing DIMMs
CAUTION: You must disconnect the power cord and wait approximately 30 seconds for the power
to drain before adding or removing memory modules. Regardless of the power-on state, voltage is
always supplied to the memory modules as long as the computer is plugged into an active AC outlet.
Adding or removing memory modules while voltage is present may cause irreparable damage to the
memory modules or system board.
The memory module sockets have gold-plated metal contacts. When upgrading the memory, it is
important to use memory modules with gold-plated metal contacts to prevent corrosion and/or
oxidation resulting from having incompatible metals in contact with each other.
Static electricity can damage the electronic components of the computer or optional cards. Before
beginning these procedures, ensure that you are discharged of static electricity by briefly touching a
grounded metal object. For more information, refer to Electrostatic Discharge Information on page 42.
When handling a memory module, be careful not to touch any of the contacts. Doing so may damage
the module.
98
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Rotate up the internal drive bay housing to access the memory module sockets on the system
board.
Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
4.
Open both latches of the memory module socket (1), and insert the memory module into the
socket (2).
Figure 7-6 Installing a DIMM
NOTE: A memory module can be installed in only one way. Match the notch on the module
with the tab on the memory socket.
Populate the black DIMM sockets before the white DIMM sockets.
For maximum performance, populate the sockets so that the memory capacity is spread as
equally as possible between Channel A and Channel B. Refer to Populating DIMM Sockets
on page 97 for more information.
5.
Push the module down into the socket, ensuring that the module is fully inserted and properly
seated. Make sure the latches are in the closed position (3).
6.
Repeat steps 4 and 5 to install any additional modules.
7.
Replace the access panel.
8.
If the computer was on a stand, replace the stand.
9.
Reconnect the power cord and turn on the computer.
10. Lock any security devices that were disengaged when the access panel was removed.
The computer should automatically recognize the additional memory the next time you turn on the
computer.
Memory
99
Expansion Card
Description
Spare part number
nVidia Quadro NVS310 PCIe x16 graphics card, 512 MB
680653-001
nVidia Quadro NVS300 PCIe x16 graphics card, 512 MB
632486-001
AMD Radeon HD7450 PCIe x16 graphics card, 1 GB
682411-001
AMD Radeon HD6350 PCIe x16 graphics card, 512 MB
637995-001
Intel PRO/1000CT2 NIC, includes bracket
635523-001
AMD FirePro 2270 PCIe x16 graphics card, 512 MB
637213-001
HP FireWire / IEEE 1394a PCIe x1 Card
637591-001
The computer has one PCI expansion slot, two PCI Express x1 expansion slots, and one PCI
Express x16 expansion slot.
NOTE:
The PCI and PCI Express slots support only low profile cards.
You can install a PCI Express x1, x4, x8, or x16 expansion card in the PCI Express x16 slot.
To remove, replace, or add an expansion card:
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Locate the correct vacant expansion socket on the system board and the corresponding
expansion slot on the back of the computer chassis.
4.
Release the slot cover retention latch that secures the PCI slot covers by lifting the green tab on
the latch and rotating the latch to the open position.
Figure 7-7 Opening the Expansion Slot Retainer
100 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
5.
Before installing an expansion card, remove the expansion slot cover or the existing expansion
card.
NOTE: Before removing an installed expansion card, disconnect any cables that may be
attached to the expansion card.
a.
If you are installing an expansion card in a vacant socket, remove the appropriate
expansion slot cover on the back of the chassis. Pull the slot cover straight up then away
from the inside of the chassis.
Figure 7-8 Removing an Expansion Slot Cover
b.
If you are removing a standard PCI card or PCI Express x1 card, hold the card at each end,
and carefully rock it back and forth until the connectors pull free from the socket. Pull the
expansion card straight up from the socket (1) then away from the inside of the chassis to
release it from the chassis frame (2). Be sure not to scrape the card against the other
components.
Figure 7-9 Removing a Standard PCI Expansion Card
Expansion Card 101
c.
If you are removing a PCI Express x16 card, pull the retention arm on the back of the
expansion socket away from the card and carefully rock the card back and forth until the
connectors pull free from the socket. Pull the expansion card straight up from the socket
then away from the inside of the chassis to release it from the chassis frame. Be sure not to
scrape the card against the other components.
Figure 7-10 Removing a PCI Express x16 Expansion Card
6.
Store the removed card in anti-static packaging.
7.
If you are not installing a new expansion card, install an expansion slot cover to close the open
slot.
CAUTION: After removing an expansion card, you must replace it with a new card or
expansion slot cover for proper cooling of internal components during operation.
102 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
8.
To install a new expansion card, hold the card just above the expansion socket on the system
board then move the card toward the rear of the chassis (1) so that the bracket on the card is
aligned with the open slot on the rear of the chassis. Press the card straight down into the
expansion socket on the system board (2).
Figure 7-11 Installing an Expansion Card
NOTE: When installing an expansion card, press firmly on the card so that the whole
connector seats properly in the expansion card slot.
9.
Rotate the slot cover retention latch back in place to secure the expansion card.
10. Connect external cables to the installed card, if needed. Connect internal cables to the system
board, if needed.
11. Replace the computer access panel.
12. If the computer was on a stand, replace the stand.
13. Reconnect the power cord and turn on the computer.
14. Lock any security devices that were disengaged when the access panel was removed.
15. Reconfigure the computer, if necessary.
Expansion Card 103
System Board Connections
Refer to the following illustration and table to identify the system board connectors for your model.
Figure 7-12 System Board Connections
Table 7-1 System Board Connections
No.
System Board Connector
System Board Label
Color
Component
1
DIMM4 (Channel A)
DIMM4
white
Memory Module
2
DIMM3 (Channel A)
DIMM3
black
Memory Module
3
DIMM2 (Channel B)
DIMM2
white
Memory Module
4
DIMM1 (Channel B)
DIMM1
black
Memory Module
5
Power
SATAPWR1
black
(unused)
6
Power
SATAPWR1
black
SATA Optical and Hard Drives
7
SATA 3.0
SATA0
dark blue
1st Hard Drive
8
SATA 2.0
SATA1
white
2nd Hard Drive, or 2nd Optical Drive
if an eSATA Adapter Cable exists
9
SATA 2.0
SATA2
white
1st Optical Drive
10
eSATA
ESATA
black
eSATA Adapter Cable, or 2nd
Optical Drive
11
Parallel Port
PAR
black
Parallel Port
12
Serial Port
COMB
black
Serial Port
13
USB
MEDIA
black
USB Device, such as a Media Card
Reader
14
Hood Lock
HLCK
black
Hood Lock
15
USB
MEDIA2
black
USB Device, such as a Media Card
Reader
16
Hood Sensor
HSENSE
white
Hood Sensor
17
PCI Express x1
X1PCIEXP1
black
Expansion Card
104 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Table 7-1 System Board Connections (continued)
No.
System Board Connector
System Board Label
Color
Component
18
PCI Express x1
X4PCIEXP
black
Expansion Card
19
PCI Express x16
X16PCIEXP
black
Expansion Card
20
PCI
PCI
white
Expansion Card
Drives
Description
Spare part number
DVD±RW drive
660408-001
DVD-ROM drive
581599-001
Blu-ray BD-RW SuperMulti DL Drive
656792-001
Blu-ray BD-Writer XL Drive
682219-001
1 TB, 7200 rpm SATA hard drive
636930-001
500 GB, 7200 rpm, 2.5 inch, SED, SATA hard drive
696442-001
500 GB, 7200 rpm SATA hard drive
636929-001
320 GB, 7200 rpm SATA hard drive, 2.5-inch
634824-001
250 GB, 7200 rpm SATA hard drive
636927-001
256 GB Solid State Drive (SSD), self-encrypting (SED), SATA 6.0
680020-001
180 GB Solid State Drive (SSD), SATA 6.0
696622-001
160 GB Solid State Drive (SSD), SATA 3.0
646809-001
128 GB Solid State Drive (SSD), SATA 2.0
665961-001
120 GB Solid State Drive (SSD), SATA 2.0
661841-001
Drives 105
Drive Positions
Figure 7-13 Drive Positions
Table 7-2 Drive Positions
1
3.5-inch internal hard drive bay
2
3.5-inch drive bay for optional drives (media card reader shown)
3
5.25-inch drive bay for optional drives (optical drive shown)
NOTE: The drive configuration on your computer may be different than the drive
configuration shown above.
To verify the type and size of the storage devices installed in the computer, run Computer Setup.
Installing and Removing Drives
When installing drives, follow these guidelines:
●
The primary Serial ATA (SATA) hard drive must be connected to the dark blue primary SATA
connector on the system board labeled SATA0. If you are adding a second hard drive, connect it
to the white connector on the system board labeled SATA1.
●
Connect a SATA optical drive to the white SATA connector on the system board labeled SATA2.
●
Connect an optional eSATA adapter cable to the black SATA connector on the system board
labeled ESATA.
●
Connect a media card reader USB cable to the USB connector on the system board labeled
MEDIA.
●
The power cable for the SATA drives is a three-headed cable that is plugged into the system
board with the first connector routed to the rear of the hard drive, the second connector routed to
the rear of the 3.5” drive, and the third connector routed to the rear of the 5.25” optical drive.
●
The system does not support Parallel ATA (PATA) optical drives or PATA hard drives.
●
You must install guide screws to ensure the drive will line up correctly in the drive cage and lock
in place. HP has provided extra guide screws for the drive bays (five 6-32 standard screws and
four M3 metric screws), installed in the front of the chassis, under the front bezel. The 6-32
standard screws are required for a secondary hard drive. All other drives (except the primary
hard drive) use M3 metric screws. The HP-supplied metric screws are black and the HPsupplied standard screws are silver. If you are replacing the primary hard drive, you must
106 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
remove the four silver and blue 6-32 isolation mounting guide screws from the old hard drive and
install them in the new hard drive.
Figure 7-14 Extra Guide Screw Locations
No.
Guide Screw
Device
1
Black M3 Metric Screws
All Drives (except primary and secondary hard drives)
2
Silver 6-32 Standard Screws
Secondary Hard Drive
There are at total of five extra silver 6-32 standard screws. Four are used as guide screws for a
secondary hard drive. The fifth is used for bezel security (see Front Bezel Security on page 94 for more
information).
CAUTION: To prevent loss of work and damage to the computer or drive:
If you are inserting or removing a drive, shut down the operating system properly, turn off the
computer, and unplug the power cord. Do not remove a drive while the computer is on or in standby
mode.
Before handling a drive, ensure that you are discharged of static electricity. While handling a drive,
avoid touching the connector.
Handle a drive carefully; do not drop it.
Do not use excessive force when inserting a drive.
Avoid exposing a hard drive to liquids, temperature extremes, or products that have magnetic fields
such as monitors or speakers.
If a drive must be mailed, place the drive in a bubble-pack mailer or other protective packaging and
label the package “Fragile: Handle With Care.”
Removing a 5.25-inch Drive from a Drive Bay
CAUTION: All removable media should be taken out of a drive before removing the drive from the
computer.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Rotate the drive cage to its upright position.
Drives 107
4.
If removing an optical drive, disconnect the power cable and data cable from the rear of the
optical drive.
CAUTION: When removing the cables, pull the tab or connector instead of the cable itself to
avoid damaging the cable.
5.
Rotate the drive cage back down to its normal position.
CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.
6.
Press down on the green drive retainer button located on the left side of the drive to disengage
the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back
until it stops, then lift it up and out of the drive cage (2).
Figure 7-15 Removing the 5.25-inch Drive
Installing a 5.25-inch Drive into a Drive Bay
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
If you are installing a drive in a bay covered by a bezel blank, remove the front bezel then
remove the bezel blank. See Bezel Blanks on page 96 for more information.
108 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
4.
Install four M3 metric guide screws in the lower holes on each side of the drive. HP has provided
four extra M3 metric guide screws on the front of the chassis, under the front bezel. The M3
metric guide screws are black. Refer to Installing and Removing Drives on page 106 for an
illustration of the extra M3 metric guide screws location.
NOTE: When replacing the drive, transfer the four M3 metric guide screws from the old drive to
the new one.
CAUTION: Use only 5-mm long screws as guide screws. Longer screws can damage the
internal components of the drive.
Figure 7-16 Installing Guide Screws in the Optical Drive
5.
Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive
toward the front of the computer until it locks into place.
Figure 7-17 Installing the Optical Drive
6.
Rotate the drive cage to its upright position.
7.
Connect the SATA data cable to the white SATA system board connector labeled SATA2.
8.
Route the data cable through the cable guides.
CAUTION: There are two cable guides that keep the data cable from being pinched by the
drive cage when raising or lowering it. One is located on the bottom side of the drive cage. The
other is located on the chassis frame under the drive cage. Ensure that the data cable is routed
through these guides before connecting it to the optical drive.
Drives 109
9.
Connect the power cable and data cable to the rear of the optical drive.
NOTE: The power cable for the optical drive is a three-headed cable that is routed from the
system board to the hard drive, then to the rear of the optical drive.
10. Rotate the drive cage back down to its normal position.
CAUTION: Be careful not to pinch any cables or wires when rotating the drive cage down.
11. Replace the front bezel (if removed) and access panel.
12. If the computer was on a stand, replace the stand.
13. Reconnect the power cord and turn on the computer.
14. Lock any security devices that were disengaged when the access panel was removed.
110 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Removing a 3.5-inch Drive from a Drive Bay
CAUTION: All removable media should be taken out of a drive before removing the drive from the
computer.
The 3.5-inch drive is located underneath the 5.25-inch drive. You must remove the 5.25-inch drive
before removing the 3.5-inch drive.
1.
Follow the procedure in Removing a 5.25-inch Drive from a Drive Bay on page 107 to remove
the 5.25-inch drive and access the 3.5-inch drive.
CAUTION: Ensure that the computer is turned off and that the power cord is disconnected
from the electrical outlet before proceeding.
2.
Disconnect the drive cables from the rear of the drive, or, if you are removing a media card
reader, disconnect the USB cable from the system board as indicated in the following illustration.
Figure 7-18 Disconnecting the Media Card Reader USB Cable
3.
Press down on the green drive retainer button located on the left side of the drive to disengage
the drive from the drive cage (1). While pressing the drive retainer button, slide the drive back
until it stops, then lift it up and out of the drive cage (2).
Figure 7-19 Removing a 3.5-inch Drive (Media Card Reader Shown)
Drives 111
Installing a 3.5-inch Drive into a Drive Bay
The 3.5-inch bay is located underneath the 5.25-inch drive. To install a drive into the 3.5-inch bay:
NOTE: Install guide screws to ensure the drive will line up correctly in the drive cage and lock in
place. HP has provided extra guide screws for the drive bays (four 6-32 standard screws and four M3
metric screws), installed in the front of the chassis, under the front bezel. A secondary hard drive
uses 6-32 standard screws. All other drives (except the primary hard drive) use M3 metric screws.
The HP-supplied M3 metric screws are black and the HP-supplied 6-32 standard screws are silver.
Refer to Installing and Removing Drives on page 106 for illustrations of the guide screw locations.
1.
Follow the procedure in Removing a 5.25-inch Drive from a Drive Bay on page 107 to remove
the 5.25-inch drive and access the 3.5-inch drive bay.
CAUTION: Ensure that the computer is turned off and that the power cord is disconnected
from the electrical outlet before proceeding.
2.
If you are installing a drive in a bay covered by a bezel blank, remove the front bezel then
remove the bezel blank. See Bezel Blanks on page 96 for more information.
3.
Install guide screws in the holes on each side of the drive.
Figure 7-20 Installing Guide Screws (Media Card Reader Shown)
4.
Position the guide screws on the drive into the J-slots in the drive bay. Then slide the drive
toward the front of the computer until it locks into place.
Figure 7-21 Installing a Drive into the 3.5-inch Drive Bay (Media Card Reader Shown)
5.
Connect the appropriate drive cables:
a.
If installing a second hard drive, connect the power cable and data cable to the rear of the
drive and connect the other end of the data cable to the white connector on the system
board labeled SATA1.
112 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
b.
If installing a media card reader, connect the USB cable from the media card reader to the
USB connector on the system board labeled MEDIA.
Figure 7-22 Connecting the Media Card Reader USB Cable
NOTE: Refer to System Board Connections on page 104 for an illustration of the system
board drive connectors.
6.
Replace the 5.25-inch drive.
7.
Replace the front bezel (if removed) and access panel.
8.
If the computer was on a stand, replace the stand.
9.
Reconnect the power cord and turn on the computer.
10. Lock any security devices that were disengaged when the access panel was removed.
Removing and Replacing the Primary 3.5-inch Internal Hard Drive
NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so
that you can transfer the data to the new hard drive.
The preinstalled 3.5-inch hard drive is located under the power supply. To remove and replace the
hard drive:
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Rotate the drive cage for internal drives to its upright position.
Drives 113
4.
Rotate the power supply to its upright position. The hard drive is located beneath the power
supply.
Figure 7-23 Raising the Power Supply
5.
Disconnect the power cable and data cable from the back of the hard drive.
6.
Press down on the green release latch next to the hard drive (1). While holding the latch down,
slide the drive forward until it stops, then lift the drive up and out of the bay (2).
Figure 7-24 Removing the Hard Drive
114 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
7.
To install a hard drive, you must transfer the silver and blue isolation mounting guide screws
from the old hard drive to the new hard drive.
Figure 7-25 Installing Hard Drive Guide Screws
8.
Align the guide screws with the slots on the chassis drive cage, press the hard drive down into
the bay, then slide it back until it stops and locks in place.
Figure 7-26 Installing the Hard Drive
9.
Connect the power cable and data cable to the back of the hard drive.
NOTE: If the system has only one SATA hard drive, the data cable must be connected to the
dark blue connector labeled SATA0 on the system board to avoid any hard drive performance
problems.
10. Rotate the drive cage for internal drives and the power supply down to their normal positions.
11. Replace the access panel.
12. If the computer was on a stand, replace the stand.
13. Reconnect the power cord and turn on the computer.
14. Lock any security devices that were disengaged when the access panel was removed.
Drives 115
Fan duct
Description
Spare part number
Fan duct
636921-001
The fan duct sits between the front fan and the heat sink.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Lift the fan duct straight up out of the chassis.
Figure 7-27 Removing the fan duct
To install the fan duct, reverse the removal procedure.
116 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Front Fan Assembly
Description
Spare part number
Front fan
645327-001
The front fan assembly is attached to the front of the chassis.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Remove the front bezel (Front Bezel on page 93).
4.
Remove the baffle (Fan duct on page 116).
5.
Disconnect the fan cable from the red/brown system board connector labeled CHFAN.
Figure 7-28 Disconnecting the front fan cable
6.
Press the tabs that secure the fan assembly to the front of the chassis (1).
Front Fan Assembly 117
7.
Pull the assembly toward the rear of the unit (2), and then lift it out of the chassis.
Figure 7-29 Removing the front fan
To install the front fan, reverse the removal procedure. Be sure to orient the air flow into the unit.
118 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Hood Sensor
Description
Spare part number
Hood sensor
638816-001
The hood sensor is attached in a slot in the rear of the chassis.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Unplug the sensor cable from the system board connector labeled HSENSE (1).
4.
Slide the hood sensor straight out of the notch in the chassis (2).
NOTE: A flat blade screwdriver can be used to push the hood sensor out of the slot.
Figure 7-30 Removing the hood sensor from the chassis fan
To install the hood sensor, reverse the removal procedure.
Hood Sensor 119
Front I/O, Power Switch Assembly
Description
Spare part number
Front I/O and power switch assembly
636926-001
The front I/O and power switch/LEDs is one assembly, attached to the front of the chassis. Push the
assembly into the chassis to remove.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Remove the front bezel (Front Bezel on page 93).
4.
Remove the chassis fan (Front Fan Assembly on page 117).
5.
Rotate the drive cage to its upright position.
6.
Disconnect the four cables from the system board as follows:
●
Yellow connector labeled FRONT_USB
●
Green connector labeled FRONT_USB2
●
Blue connector labeled FRONT AUD
●
Black connector labeled PB/LED
Figure 7-31 Disconnecting the front I/O, power switch/LED assembly cables
7.
Remove the Torx T15 screw (1) that secures the assembly to the front of the chassis.
120 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
8.
Route the cables through the slots beneath the drive cage, rotate the assembly into the chassis
(2), and then remove the assembly from the computer.
Figure 7-32 Removing the front I/O, power switch/LED assembly screw
To install the front I/O and power switch assembly, reverse the removal procedure.
NOTE: Be sure to correctly route the cables beneath the drive cage when reinstalling the assembly.
Proper cable routing prevents damage to the cables and allows the drive cage to close properly.
Front I/O, Power Switch Assembly 121
Speaker
Description
Spare part number
Speaker
636925-001
The speaker is attached to the front of the chassis under the rotating drive cage.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Remove the front bezel (Front Bezel on page 93).
4.
Rotate the drive cage to its upright position.
5.
Disconnect the speaker wire from the white system board labeled SPKR (1).
6.
Remove the Torx screw that secures the speaker to the chassis (2).
7.
Lift the speaker from the inside of the chassis to remove it (3).
Figure 7-33 Removing the speaker
To install the speaker, reverse the removal procedures.
122 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Heat sink
Description
Spare part number
Heat sink
645326-001
The heat sink is secured atop the processor with four captive Torx screws. The heat sink does not
include a fan.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Remove the fan duct (Fan duct on page 116).
4.
Remove the front fan (Front Fan Assembly on page 117).
5.
In the order shown, loosen the four captive screws that secure the heat sink to the system board
tray.
CAUTION: Heat sink retaining screws should be removed in diagonally opposite pairs (as in
an X) to even the downward forces on the processor. This is especially important as the pins on
the socket are very fragile and any damage to them may require replacing the system board.
Figure 7-34 Loosening the heat sink screws
Heat sink 123
6.
After loosening the Torx T15 screws (1), lift the heat sink from atop the processor (2) and set it
on its side to keep from contaminating the work area with thermal grease.
Figure 7-35 Removing the heat sink
When reinstalling the heat sink, make sure that its bottom has been cleaned with an alcohol wipe and
fresh thermal grease has been applied to the top of the processor.
CAUTION: Heat sink retaining screws should be tightened in diagonally opposite pairs (as in an X)
to evenly seat the heat sink on the processor to avoid damage that could require replacing the system
board.
Failure to install the fan duct may cause the computer to overheat.
124 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
Processor
Description
Spare part number
Intel Core i7 processor
3770, 3.4 GHz, 8-MB L3 cache, 95W
688164-001
Intel Core i5 processors
3570, 3.4 GHz, 6-MB L3 cache, 95W
688162-001
3470, 3.2 GHz, 6-MB L3 cache, 95W
687943-001
Intel Core i3 processors
3240, 3.4 GHz, 3-MB L3 cache
688951-001
3225, 3.3 GHz, 3-MB L3 cache, 55W
689578-001
3220, 3.3 GHz, 3-MB L3 cache, 65W
688950-001
2130, 3.4 GHz, 3-MB L3 cache
665120-001
2120, 3.3 GHz, 3-MB L3 cache
638629-001
Intel Pentium processors
G870, 3.1 GHz, 3-MB L3 cache
691936-001
G860, 3.0 GHz, 3-MB L3 cache
665123-001
G850, 2.9 GHz, 3-MB L3 cache
655973-001
G640, 2.8 GHz, 3-MB L3 cache
691935-001
G630, 2.7 GHz, 3-MB L3 cache
665122-001
Intel Celeron processors
G550, 2.6 GHz, 2-MB L3 cache
691934-001
G540, 2.5 GHz, 2-MB L3 cache
665119-001
G530T, 2.0 GHz, 2-MB L3 cache
665118-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Remove the fan duct (Fan duct on page 116).
4.
Remove the front fan assembly (Front Fan Assembly on page 117).
5.
Remove the heat sink (Heat sink on page 123).
6.
Rotate the locking lever to its full open position (1).
7.
Raise and rotate the microprocessor retainer to its fully open position (2).
Processor 125
8.
Carefully lift the processor from the socket (3).
CAUTION: Do NOT handle the pins in the processor socket. These pins are very fragile and
handling them could cause irreparable damage. Once pins are damaged it may be necessary to
replace the system board.
The heat sink must be installed within 24 hours of installing the processor to prevent damage to
the processor’s solder connections.
Figure 7-36 Removing the processor
To install a new processor:
1.
Place the processor in its socket and close the retainer. Make sure the slot in the processor fits
into the post on the socket.
126 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
2.
Secure the locking lever. If reusing the existing heat sink, go to step 3. If using a new heat sink,
go to step 6.
Figure 7-37 Removing the processor
3.
If reusing the existing heat sink, clean the bottom of the heat sink with the alcohol pad provided
in the spares kit.
CAUTION: Before reinstalling the heat sink you must clean the top of the processor and the
bottom of the heat sink with an alcohol pad supplied in the spares kit. After the alcohol has
evaporated, apply thermal grease to the top of the processor from the syringe supplied in the
spares kit.
4.
Apply the thermal grease provided in the spares kit to the top of the processor and install the
heat sink atop the processor.
5.
Go to step 7.
6.
If using a new heat sink, remove the protective covering from the bottom of the heat sink and
place it in position atop the processor.
7.
Secure the heat sink to the system board and system board tray.
CAUTION: Heat sink retaining screws should be tightened in diagonally opposite pairs (as in
an X) to evenly seat the heat sink on the processor. This is especially important as the pins on
the socket are very fragile and any damage to them may require replacing the system board.
NOTE: After installing a new processor onto the system board, always update the system ROM to
ensure that the latest version of the BIOS is being used on the computer. The latest system BIOS can
be found on the Web at: http://h18000.www1.hp.com/support/files.
Processor 127
Power Supply
Description
Spare part number
Power supply, 90% efficient
613762-001
Power supply, standard
613763-001
WARNING! To reduce potential safety issues, only the power supply provided with the computer, a
replacement power supply provided by HP, or a power supply purchased as an accessory from HP
should be used with the computer.
The rotating power supply is located at the rear of the chassis. It is held in place by a bracket – no
screws are used.
WARNING! Voltage is always present on the system board when the computer is plugged into an
active AC outlet. To avoid possible personal injury and damage to the equipment the power cord
should be disconnected from the computer and/or the AC outlet before opening the computer.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
Rotate the drive cage up and disconnect the power cables from all of the drives.
4.
Disconnect all power cables from the system board as follows:
●
4-pin PWRCPU
●
6-pin PWR
●
6-pin PWRCMD
5.
Rotate the power supply to its full upright position.
6.
Release the power supply cables from the cable retaining clip under the drive cage.
128 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
7.
Pull the power supply forward until the posts on the power supply move forward in the power
supply bracket, and then lift the power supply straight up and out of the chassis.
Figure 7-38 Removing the power supply
To install the power supply, reverse the removal procedure.
CAUTION: When installing the power supply cables, make sure they are properly positioned so
they are not cut by the drive cage and are not pinched by the rotating power supply.
Power Supply 129
System Board
Description
Spare part number
System board (includes thermal material)
657239-001
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Remove the access panel (Access Panel on page 92).
3.
When replacing the system board, make sure the following components are removed from the
defective system board and installed on the replacement system board:
●
Memory modules (Memory on page 97)
●
Expansion cards (Expansion Card on page 100)
●
Heat sink (Heat sink on page 123)
●
Processor (Processor on page 125)
4.
Remove the baffle from the chassis (Fan duct on page 116).
5.
Remove the fan from the chassis (Front Fan Assembly on page 117).
6.
Rotate the drive cage to its upright position.
7.
Rotate the power supply to its full upright position.
8.
Disconnect all data and power cables from the system board.
9.
Disconnect the balance of the cables from the system board.
10. Remove the eight Torx T15 screws (1) that secure the system board to the chassis.
130 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
11. Lift up the front of the system board, and then pull the system board forward, up, and out of the
chassis (2).
Figure 7-39 Removing the system board
To install the system board, reverse the removal procedure.
NOTE:
BIOS.
When replacing the system board, you must also change the chassis serial number in the
CAUTION: Before reinstalling the heat sink you must clean the top of the processor and the bottom
of the heat sink with an alcohol pad supplied in the spares kit. After the alcohol has evaporated, apply
thermal grease to the top of the processor from the syringe supplied in the spares kit.
CAUTION: When reconnecting the cables it is important that they be positioned so they do not
interfere with the rotation of the drive cage or power supply.
System Board 131
Using the Small Form Factor Computer in a Tower
Orientation
The Small Form Factor computer can be used in a tower orientation. The HP logo plate on the front
bezel is adjustable for either desktop or tower orientation.
1.
Prepare the computer for disassembly (Preparation for Disassembly on page 91).
2.
Orient the computer so that its right side is facing down and place the computer in the optional
stand.
Figure 7-40 Changing from Desktop to Tower Orientation
NOTE: To stabilize the computer in a tower orientation, HP recommends the use of the
optional tower stand.
3.
Lock any security devices that were disengaged when the access panel was removed.
NOTE: Ensure at least 10.2 centimeters (4 inches) of space on all sides of the computer remains
clear and free of obstructions.
132 Chapter 7 Removal and Replacement Procedures Small Form Factor (SFF) Chassis
8
Troubleshooting Without Diagnostics
This chapter provides information on how to identify and correct minor problems, such as diskette
drive, hard drive, optical drive, graphics, audio, memory, and software problems. If you encounter
problems with the computer, refer to the tables in this chapter for probable causes and recommended
solutions.
NOTE: For information on specific error messages that may appear on the screen during Power-On
Self-Test (POST) at startup, refer to Appendix A, POST Error Messages on page 175.
Safety and Comfort
WARNING! Misuse of the computer or failure to establish a safe and comfortable work environment
may result in discomfort or serious injury. Refer to the Safety & Comfort Guide at http://www.hp.com/
ergo for more information on choosing a workspace and creating a safe and comfortable work
environment. For more information, refer to the Safety & Regulatory Information guide.
Before You Call for Technical Support
If you are having problems with the computer, try the appropriate solutions below to try to isolate the
exact problem before calling for technical support.
●
Run the HP diagnostic tool.
●
Run the hard drive self-test in Computer Setup. Refer to Computer Setup (F10) Utility
on page 10 for more information.
●
Check the Power LED on the front of the computer to see if it is flashing red. The flashing lights
are error codes that will help you diagnose the problem. Refer to Appendix A, POST Error
Messages on page 175 for more information.
●
If the screen is blank, plug the monitor into a different video port on the computer if one is
available. Or, replace the monitor with a monitor that you know is functioning properly.
●
If you are working on a network, plug another computer with a different cable into the network
connection. There may be a problem with the network plug or cable.
●
If you recently added new hardware, remove the hardware and see if the computer functions
properly.
●
If you recently installed new software, uninstall the software and see if the computer functions
properly.
●
Boot the computer to the Safe Mode to see if it will boot without all of the drivers loaded. When
booting the operating system, use “Last Known Configuration.”
Safety and Comfort 133
●
Refer to the comprehensive online technical support at http://www.hp.com/support.
●
Refer to Helpful Hints on page 134 in this guide.
To assist you in resolving problems online, HP Instant Support Professional Edition provides you with
self-solve diagnostics. If you need to contact HP support, use HP Instant Support Professional
Edition's online chat feature. Access HP Instant Support Professional Edition at: http://www.hp.com/
go/ispe.
Access the Business Support Center (BSC) at http://www.hp.com/go/bizsupport for the latest online
support information, software and drivers, proactive notification, and worldwide community of peers
and HP experts.
If it becomes necessary to call for technical assistance, be prepared to do the following to ensure that
your service call is handled properly:
●
Be in front of your computer when you call.
●
Write down the computer serial number, product ID number, and monitor serial number before
calling.
●
Spend time troubleshooting the problem with the service technician.
●
Remove any hardware that was recently added to your system.
●
Remove any software that was recently installed.
●
Restore the system from the Recovery Disc Set that you created or restore the system to its
original factory condition in HP Backup and Recovery Manager.
CAUTION: Restoring the system will erase all data on the hard drive. Be sure to back up all data
files before running the restore process.
NOTE: For sales information and warranty upgrades (Care Packs), call your local authorized
service provider or dealer.
Helpful Hints
If you encounter problems with the computer, monitor, or software, see the following list of general
suggestions before taking further action:
●
Check that the computer and monitor are plugged into a working electrical outlet.
●
Check that the voltage select switch (some models) is set to the appropriate voltage for your
region (115V or 230V).
●
Check that the computer is turned on and the green power light is on.
●
Check that the monitor is turned on and the green monitor light is on.
●
Check the Power LED on the front of the computer to see if it is flashing red. The flashing lights
are error codes that will help you diagnose the problem. Refer to Appendix A, POST Error
Messages on page 175 for more information.
●
Turn up the brightness and contrast controls of the monitor if the monitor is dim.
●
Press and hold any key. If the system beeps, then the keyboard should be operating correctly.
●
Check all cable connections for loose connections or incorrect connections.
134 Chapter 8 Troubleshooting Without Diagnostics
●
Wake the computer by pressing any key on the keyboard or pressing the power button. If the
system remains in suspend mode, shut down the computer by pressing and holding the power
button for at least four seconds then press the power button again to restart the computer. If the
system will not shut down, unplug the power cord, wait a few seconds, then plug it in again. The
computer will restart if it is set to power on automatically as soon as power is restored in
Computer Setup. If it does not restart, press the power button to start the computer.
●
Reconfigure the computer after installing a non-plug and play expansion board or other option.
See Solving Hardware Installation Problems on page 160 for instructions.
●
Be sure that all the needed device drivers have been installed. For example, if you are using a
printer, you need a driver for that model printer.
●
Remove all bootable media (diskette, CD, or USB device) from the system before turning it on.
●
If you have installed an operating system other than the factory-installed operating system,
check to be sure that it is supported on the system.
●
If the system has multiple video sources (embedded, PCI, or PCI-Express adapters) installed
(embedded video on some models only) and a single monitor, the monitor must be plugged into
the monitor connector on the source selected as the primary VGA adapter. During boot, the
other monitor connectors are disabled and if the monitor is connected into these ports, the
monitor will not function. You can select which source will be the default VGA source in
Computer Setup.
CAUTION: When the computer is plugged into an AC power source, there is always voltage applied
to the system board. You must disconnect the power cord from the power source before opening the
computer to prevent system board or component damage.
Helpful Hints 135
Solving General Problems
You may be able to easily resolve the general problems described in this section. If a problem
persists and you are unable to resolve it yourself or if you feel uncomfortable about performing the
operation, contact an authorized dealer or reseller.
WARNING! When the computer is plugged into an AC power source, voltage is always applied to
the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.
Table 8-1 Solving General Problems
Computer appears locked up and will not turn off when the power button is pressed.
Cause
Solution
Software control of the power switch is not functional.
1.
Press and hold the power button for at least four
seconds until the computer turns off.
2.
Disconnect the power cord from the electrical outlet.
Computer will not respond to USB keyboard or mouse.
Cause
Solution
Computer is in standby mode.
To resume from standby mode, press the power button or
press any key.
CAUTION: When attempting to resume from standby
mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.
System has locked up.
Restart computer.
Computer date and time display is incorrect.
Cause
Solution
RTC (real-time clock) battery may need to be replaced.
First, reset the date and time under Control Panel
(Computer Setup can also be used to update the RTC date
and time). If the problem persists, replace the RTC battery.
See the Removal and Replacement section for instructions
on installing a new battery, or contact an authorized dealer or
reseller for RTC battery replacement.
NOTE: Connecting the computer to a live AC outlet
prolongs the life of the RTC battery.
Cursor will not move using the arrow keys on the keypad.
Cause
Solution
The Num Lock key may be on.
Press the Num Lock key. The Num Lock light should not be
on if you want to use the arrow keys. The Num Lock key can
be disabled (or enabled) in Computer Setup.
136 Chapter 8 Troubleshooting Without Diagnostics
There is no sound or sound volume is too low.
Cause
Solution
System volume may be set low or muted.
1.
Check the F10 BIOS settings to make sure the internal
system speaker is not muted (this setting does not
affect the external speakers).
2.
Make sure the external speakers are properly
connected and powered on and that the speakers'
volume control is set correctly.
3.
Use the system volume control available in the
operating system to make sure the speakers are not
muted or to increase the volume.
Cannot remove computer cover or access panel.
Cause
Solution
Smart Cover Lock, featured on some computers, is locked.
Unlock the Smart Cover Lock using Computer Setup.
The Smart Cover FailSafe Key, a device for manually
disabling the Smart Cover Lock, is available from HP. You
will need the FailSafe Key in case of forgotten password,
power loss, or computer malfunction. Order PN 166527-001
for the wrench-style key or PN 166527-002 for the
screwdriver bit key.
Poor performance is experienced.
Cause
Solution
Processor is hot.
1.
Make sure airflow to the computer is not blocked. Leave
a 10.2-cm (4-inch) clearance on all vented sides of the
computer and above the monitor to permit the required
airflow.
2.
Make sure fans are connected and working properly
(some fans only operate when needed).
3.
Make sure the processor heat sink is installed properly.
Hard drive is full.
Transfer data from the hard drive to create more space on
the hard drive.
Low on memory.
Add more memory.
Hard drive fragmented.
Defragment hard drive.
Program previously accessed did not release reserved
memory back to the system.
Restart the computer.
Virus resident on the hard drive.
Run virus protection program.
Solving General Problems 137
Table 8-1 Solving General Problems (continued)
Poor performance is experienced.
Cause
Solution
Too many applications running.
1.
Close unnecessary applications to free up memory.
2.
Add more memory. Some applications run in the
background and can be closed by right-clicking on their
corresponding icons in the task tray. To prevent these
applications from launching at startup, go to Start >
Run (Windows XP) or Start > All Programs >
Accessories > Run (Windows 7) and type msconfig.
On the Startup tab of the System Configuration Utility,
clear applications that you do not want to launch
automatically.
1.
Lower the display resolution for the current application
or consult the documentation that came with the
application for suggestions on how to improve
performance by adjusting parameters in the application.
2.
Add more memory.
3.
Upgrade the graphics solution.
Some software applications, especially games, are stressful
on the graphics subsystem
Cause unknown.
Restart the computer.
Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a
two second pause, and the computer beeps two times. (Beeps stop after fifth iteration but LEDs continue flashing).
Cause
Solution
Processor thermal protection activated:
1.
Ensure that the computer air vents are not blocked and
the processor cooling fan is running.
2.
Open hood, press power button, and see if the
processor fan spins. If the processor fan is not spinning,
make sure the fan's cable is plugged onto the system
board header.
3.
If fan is plugged in, but is not spinning, then replace the
heat sink/fan assembly.
4.
Contact an authorized reseller or service provider.
A fan may be blocked or not turning.
OR
The heat sink is not properly attached to the processor.
138 Chapter 8 Troubleshooting Without Diagnostics
System does not power on and the LEDs on the front of the computer are not flashing.
Cause
Solution
System unable to power on.
Press and hold the power button for less than 4 seconds. If
the hard drive LED turns green, then:
1.
Check that the voltage selector, located on the rear of
the power supply on some models, is set to the
appropriate voltage. Proper voltage setting depends on
your region.
2.
Remove the expansion cards one at a time until the
5V_aux light on the system board turns on.
3.
Replace the system board.
OR
Press and hold the power button for less than 4 seconds. If
the hard drive LED does not turn on green then:
1.
Check that the unit is plugged into a working AC outlet.
2.
Open hood and check that the power button harness is
properly connected to the system board.
3.
Check that both power supply cables are properly
connected to the system board.
4.
Check to see if the 5V_aux light on the system board is
turned on. If it is turned on, then replace the power
button harness.
5.
If the 5V_aux light on the system board is off, then
replace the power supply.
6.
Replace the system board.
Solving General Problems 139
Solving Power Problems
Common causes and solutions for power problems are listed in the following table.
Table 8-2 Solving Power Problems
Power supply shuts down intermittently.
Cause
Solution
Voltage selector switch on rear of computer chassis (some
models) not switched to correct line voltage (115V or 230V).
Select the proper AC voltage using the selector switch.
Power supply will not turn on because of internal power
supply fault.
Contact an authorized service provider to replace the power
supply.
Computer powered off automatically and the Power LED flashes Red two times, once every second, followed by a
two second pause, and the computer beeps two times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Processor thermal protection activated:
1.
Ensure that the computer air vents are not blocked and
the processor cooling fan is running.
2.
Open hood, press power button, and see if the
processor fan spins. If the processor fan is not spinning,
make sure the fan's cable is plugged onto the system
board header.
3.
If fan is plugged in, but is not spinning, then replace the
heat sink/fan assembly.
4.
Contact an authorized reseller or service provider.
A fan may be blocked or not turning.
OR
The heat sink is not properly attached to the processor.
140 Chapter 8 Troubleshooting Without Diagnostics
Power LED flashes Red four times, once every second, followed by a two second pause, and the computer beeps
four times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Power failure (power supply is overloaded).
1.
Check that the voltage selector, located on the rear of
the power supply (some models), is set to the
appropriate voltage. Proper voltage setting depends on
your region.
2.
Open the hood and ensure the 4- or 6-wire power
supply cable is seated into the connector on the system
board.
3.
Check if a device is causing the problem by removing
ALL attached devices (such as hard, diskette, or optical
drives, and expansion cards). Power on the system. If
the system enters the POST, then power off and
replace one device at a time and repeat this procedure
until failure occurs. Replace the device that is causing
the failure. Continue adding devices one at a time to
ensure all devices are functioning properly.
4.
Replace the power supply.
5.
Replace the system board.
The incorrect external power supply adapter is being used on
the USDT.
The USDT power supply adapter must be at 135W and use
the Smart ID technology before the system will power up.
Replace the power supply adapter with the HP-supplied
USDT power supply adapter.
Solving Power Problems 141
Solving Diskette Problems
Common causes and solutions for diskette problems are listed in the following table.
NOTE: The computer does not support internal diskette drives. Only USB diskette drives are
supported.
NOTE: You may need to reconfigure the computer when you add or remove hardware, such as an
additional diskette drive. See Solving Hardware Installation Problems on page 160 for instructions.
Table 8-3 Solving Diskette Problems
Diskette drive light stays on.
Cause
Solution
Diskette is damaged.
In Microsoft Windows XP, right-click Start, click Explore,
and select a drive. Select File > Properties > Tools. Under
Error-checking click Check Now.
In Windows 7, right-click Start, click Explore, and right-click
on a drive. Select Properties then select the Tools tab.
Under Error-checking click Check Now.
Diskette is incorrectly inserted.
Remove diskette and reinsert.
Drive cable is not properly connected.
Reconnect drive cable. Ensure that all four pins on the
diskette power cable are connected to the drive.
Drive not found.
Cause
Solution
Cable is loose.
Reseat diskette drive data and power cable.
Removable drive is not seated properly.
Reseat the drive.
The device has been hidden in Computer Setup.
Run the Computer Setup utility and ensure Device Available
is selected for the Legacy Diskette in Security > Device
Security.
Diskette drive cannot write to a diskette.
Cause
Solution
Diskette is not formatted.
Format the diskette.
1.
From Windows Explorer select the disk (A) drive.
2.
Right-click the drive letter and select Format.
3.
Select the desired options, and click Start to begin
formatting the diskette.
Diskette is write-protected.
Use another diskette or remove the write protection.
Writing to the wrong drive.
Check the drive letter in the path statement.
142 Chapter 8 Troubleshooting Without Diagnostics
Table 8-3 Solving Diskette Problems (continued)
Diskette drive cannot write to a diskette.
Cause
Solution
Not enough space is left on the diskette.
1.
Use another diskette.
2.
Delete unneeded files from diskette.
Diskette is damaged.
Replace the damaged disk.
Cannot format diskette.
Cause
Solution
Invalid media reported.
When formatting a disk in MS-DOS, you may need to specify
diskette capacity. For example, to format a 1.44-MB diskette,
type the following command at the MS-DOS prompt:
FORMAT A: /F:1440
Disk may be write-protected.
Open the locking device on the diskette.
Legacy diskette writes are disabled in Computer Setup.
Enter Computer Setup and enable Legacy Diskette Write in
Storage > Storage Options.
A problem has occurred with a disk transaction.
Cause
Solution
The directory structure is bad, or there is a problem with a
file.
In Microsoft Windows XP, right-click Start, click Explore,
and select a drive. Select File > Properties > Tools. Under
Error-checking, click Check Now.
In Windows 7, right-click Start, click Explore, and right-click
on a drive. Select Properties then select the Tools tab.
Under Error-checking click Check Now.
Diskette drive cannot read a diskette.
Cause
Solution
You are using the wrong diskette type for the drive type.
Check the type of drive that you are using and use the
correct diskette type.
You are reading the wrong drive.
Check the drive letter in the path statement.
Diskette is damaged.
Replace the diskette with a new one.
Solving Diskette Problems 143
“Invalid system disk” message is displayed.
Cause
Solution
A diskette that does not contain the system files needed to
start the computer has been inserted in the drive.
When drive activity stops, remove the diskette and press the
Spacebar. The computer should start up.
Diskette error has occurred.
Restart the computer by pressing the power button.
Cannot Boot to Diskette.
Cause
Solution
Diskette is not bootable.
Replace with a bootable diskette.
Diskette boot has been disabled in Computer Setup.
1.
Run Computer Setup and enable USB device in
Storage > Boot Order.
2.
Run Computer Setup and enable USB device in
Storage > Storage Options > Removable Media
Boot.
NOTE: Both steps should be used as the Removable
Media Boot function in Computer Setup overrides the Boot
Order enable command.
Network server mode is enabled in Computer Setup.
144 Chapter 8 Troubleshooting Without Diagnostics
Run Computer Setup and disable Network Server Mode in
Security > Password Options.
Solving Hard Drive Problems
Table 8-4 Solving Hard Drive Problems
Hard drive error occurs.
Cause
Solution
Hard disk has bad sectors or has failed.
1.
In Microsoft Windows XP, right-click Start, click
Explore, and select a drive. Select File > Properties >
Tools. Under Error-checking, click Check Now.
In Windows 7, right-click Start, click Explore, and rightclick on a drive. Select Properties then select the
Tools tab. Under Error-checking click Check Now.
2.
Use a utility to locate and block usage of bad sectors. If
necessary, reformat the hard disk.
Disk transaction problem.
Cause
Solution
Either the directory structure is bad or there is a problem with
a file.
In Microsoft Windows XP, right-click Start, click Explore,
and select a drive. Select File > Properties > Tools. Under
Error-checking, click Check Now.
In Windows 7, right-click Start, click Explore, and right-click
on a drive. Select Properties then select the Tools tab.
Under Error-checking click Check Now.
Drive not found (identified).
Cause
Solution
Cable could be loose.
Check cable connections.
The system may not have automatically recognized a newly
installed device.
See reconfiguration directions in the Solving Hardware
Installation Problems on page 160 section. If the system still
does not recognize the new device, check to see if the
device is listed within Computer Setup. If it is listed, the
probable cause is a driver problem. If it is not listed, the
probable cause is a hardware problem.
If this is a newly installed drive, run the Computer Setup
utility and try adding a POST delay under Advanced >
Power-On.
The device is attached to a SATA port that has been hidden
in Computer Setup.
Run the Computer Setup utility and ensure Device Available
is selected for the device's SATA port in Security > Device
Security.
Drive responds slowly immediately after power-up.
Run Computer Setup and increase the POST Delay in
Advanced > Power-On Options.
Solving Hard Drive Problems 145
Nonsystem disk/NTLDR missing message.
Cause
Solution
The system is trying to start from a diskette that is not
bootable.
Remove the diskette from the diskette drive.
The system is trying to start from the hard drive but the hard
drive may have been damaged.
1.
Insert a bootable diskette into the diskette drive and
restart the computer.
2.
Check the hard drive format using fdisk: If NTFS
formatting, use a third party reader to evaluate the
drive. If FAT32 formatting, the hard drive cannot be
accessed.
1.
Insert a bootable diskette into the diskette drive and
restart the computer.
2.
Check the hard drive format using Fdisk: If NFTFS
formatting, use a third party reader to evaluate the
drive. If FAT32 formatting, the hard drive cannot be
accessed.
3.
Install system files for the appropriate operating system.
System files missing or not properly installed.
Hard drive boot has been disabled in Computer Setup.
Run the Computer Setup utility and enable the hard drive
entry in the Storage > Boot Order list.
Bootable hard drive is not attached as first in a multi-hard
drive configuration.
If attempting to boot from a hard drive, ensure it is attached
to the system board dark blue SATA connector.
Bootable hard drive's controller is not listed first in the Boot
Order.
Run the Computer Setup utility and select Storage > Boot
Order and ensure the bootable hard drive's controller is
listed immediately under the Hard Drive entry.
Computer will not boot from hard drive.
Cause
Solution
The device is attached to a SATA port that has been hidden
in Computer Setup.
Run the Computer Setup utility and ensure Device Available
is selected for the device's SATA port in Security > Device
Security.
Boot order is not correct.
Run the Computer Setup utility and change boot sequence in
Storage > Boot Order.
Hard Drive's “Emulation Type” is set to “None.”
Run the Computer Setup utility and change the “Emulation
Type” to “Hard Disk” in the device's details under Storage >
Device Configuration.
Hard drive is damaged.
Observe if the front panel Power LED is blinking RED and if
any beeps are heard. See Appendix A, POST Error
Messages on page 175 to determine possible causes for the
blinking red and beep codes.
See the Worldwide Limited Warranty for terms and
conditions.
146 Chapter 8 Troubleshooting Without Diagnostics
Computer seems to be locked up.
Cause
Solution
Program in use has stopped responding to commands.
Attempt the normal Windows “Shut Down” procedure. If this
fails, press the power button for four or more seconds to turn
off the power. To restart the computer, press the power
button again.
The removable hard drive has no power to the hard drive enclosure.
Cause
Solution
The lock on the enclosure is not turned to the “ON” position.
Insert the key and turn the lock clockwise 90 degrees. The
green LED on the front of the enclosure should be on.
Power cable from the computer power supply to the
enclosure frame is not properly connected.
Check the power supply to make sure it is properly
connected to the rear of the enclosure frame.
The removable hard drive is not recognized by the computer.
Cause
Solution
The removable hard drive carrier is not fully seated in the
enclosure frame or the hard drive is not fully seated in the
carrier.
Push the carrier into the enclosure frame so that the
connector on the rear of the frame is properly seated. If this
does not solve the problem, turn off the computer, remove
the carrier, and check to see if the connector on the hard
drive is properly seated in the carrier.
The removable hard drive enclosure is beeping and the green LED is flashing.
Cause
Solution
Fan failure alarm on the removable hard drive enclosure has
been activated.
Shut down the computer and contact HP for a replacement
enclosure.
Solving Hard Drive Problems 147
Solving Media Card Reader Problems
Table 8-5 Solving Media Card Reader Problems
Media card will not work in a digital camera after formatting it in Microsoft Windows XP.
Cause
Solution
By default, Windows will format any media card with a
capacity greater than 32MB with the FAT32 format. Most
digital cameras use the FAT (FAT16 & FAT12) format and
can not operate with a FAT32 formatted card.
Either format the media card in the digital camera or select
FAT file system to format the media card in a computer with
Windows.
A write-protected or locked error occurs when attempting to write to the media card.
Cause
Solution
Media card is locked. Locking the media card is a safety
feature that prevents writing to and deleting from an SD/
Memory Stick/PRO card.
If using an SD card, make sure that the lock tab located on
the right of the SD card is not in the locked position. If using
a Memory Stick/PRO card, make sure that the lock tab
located on the bottom of the Memory Stick/PRO card is not
in the locked position.
Can not write to the media card.
Cause
Solution
The media card is a read-only memory (ROM) card.
Check the manufacturer’s documentation included with your
card to see if it writable. Refer to the previous section for a
list of compatible cards.
Media card is locked. Locking the media card is a safety
feature that prevents writing to and deleting from an SD/
Memory Stick/PRO card.
If using an SD card, make sure that the lock tab located on
the right of the SD card is not in the locked position. If using
a Memory Stick/PRO card, make sure that the lock tab
located on the bottom of the Memory Stick/PRO card is not
in the locked position.
Unable to access data on the media card after inserting it into a slot.
Cause
Solution
The media card is not inserted properly, is inserted in the
wrong slot, or is not supported.
Ensure that the card is inserted properly with the gold
contact on the correct side. The green LED will light if
inserted properly.
148 Chapter 8 Troubleshooting Without Diagnostics
Do not know how to remove a media card correctly.
Cause
Solution
The computer’s software is used to safely eject the card.
Open My Computer (Windows XP) or Computer (Windows
7), right-click on the corresponding drive icon, and select
Eject. Then pull the card out of the slot.
NOTE: Never remove the card when the green LED is
flashing
After installing the media card reader and booting to Windows, the reader and the inserted cards are not recognized
by the computer.
Cause
Solution
The operating system needs time to recognize the device if
the reader was just installed into the computer and you are
turning the PC on for the first time.
Wait a few seconds so that the operating system can
recognize the reader and the available ports, and then
recognize whatever media is inserted in the reader.
After inserting a media card in the reader, the computer attempts to boot from the media card.
Cause
Solution
The inserted media card has boot capability.
If you do not want to boot from the media card, remove it
during boot or do not select the option to boot from the
inserted media card during the boot process.
Solving Media Card Reader Problems 149
Solving Display Problems
If you encounter display problems, see the documentation that came with the monitor and to the
common causes and solutions listed in the following table.
Table 8-6 Solving Display Problems
Blank screen (no video).
Cause
Solution
Monitor is not turned on and the monitor light is not on.
Turn on the monitor and check that the monitor light is on.
Bad monitor.
Try a different monitor.
The cable connections are not correct.
Check the cable connection from the monitor to the computer
and to the electrical outlet.
You may have a screen blanking utility installed or energy
saver features are enabled.
Press any key or click the mouse button and, if set, type your
password.
System ROM is corrupted; system is running in Boot Block
Emergency Recovery Mode (indicated by eight beeps).
Reflash the system ROM with the latest BIOS image.
You are using a fixed-sync monitor and it will not sync at the
resolution chosen.
Be sure that the monitor can accept the same horizontal
scan rate as the resolution chosen.
Computer is in standby mode.
Press the power button to resume from standby mode.
CAUTION: When attempting to resume from standby
mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.
Monitor cable is plugged into the wrong connector.
Systems may have a monitor connection on both the
motherboard or an add-in card. Try moving the monitor
connection to a different connector on the back of the
computer
Monitor settings in the computer are not compatible with the
monitor.
1.
In Windows XP Control Panel, double-click the Display
icon and select the Settings tab.
In Windows 7 Control Panel, under Appearance and
Personalization, select Adjust screen resolution.
2.
Monitor is configured to use an input that is not active.
150 Chapter 8 Troubleshooting Without Diagnostics
Use the sliding control to reset the resolution.
Use the monitor's on-screen menu controls to select the
input that is being driven by the system. Refer to the
monitor's user documentation for more information on the onscreen controls and settings.
Blank screen and the power LED flashes Red five times, once every second, followed by a two second pause, and
the computer beeps five times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Pre-video memory error.
1.
Reseat DIMMs. Power on the system.
2.
Replace DIMMs one at a time to isolate the faulty
module.
3.
Replace third-party memory with HP memory.
4.
Replace the system board.
Blank screen and the power LED flashes Red six times, once every second, followed by a two second pause, and
the computer beeps six times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Pre-video graphics error.
For systems with a graphics card:
1.
Reseat the graphics card. Power on the system.
2.
Replace the graphics card.
3.
Replace the system board.
For systems with integrated graphics, replace the system
board.
Blank screen and the power LED flashes Red seven times, once every second, followed by a two second pause, and
the computer beeps seven times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
System board failure (ROM detected failure prior to video).
Replace the system board.
Monitor does not function properly when used with energy saver features.
Cause
Solution
Monitor without energy saver capabilities is being used with
energy saver features enabled.
Disable monitor energy saver feature.
Dim characters.
Cause
Solution
The brightness and contrast controls are not set properly.
Adjust the monitor brightness and contrast controls.
Cables are not properly connected.
Check that the graphics cable is securely connected to the
graphics card and the monitor.
Solving Display Problems 151
Blurry video or requested resolution cannot be set.
Cause
Solution
If the graphics controller was upgraded, the correct graphics
drivers may not be loaded.
Install the video drivers included in the upgrade kit.
Monitor is not capable of displaying requested resolution.
Change requested resolution.
Graphics card is bad.
Replace the graphics card.
The picture is broken up, rolls, jitters, or flashes.
Cause
Solution
The monitor connections may be incomplete or the monitor
may be incorrectly adjusted.
1.
Be sure the monitor cable is securely connected to the
computer.
2.
In a two-monitor system or if another monitor is in close
proximity, be sure the monitors are not interfering with
each other’s electromagnetic field by moving them
apart.
3.
Fluorescent lights or fans may be too close to the
monitor.
Monitor needs to be degaussed.
Degauss the monitor. Refer to the documentation that came
with the monitor for instructions.
Image is not centered.
Cause
Solution
Position may need adjustment.
Press the monitor's Menu button to access the OSD menu.
Select ImageControl/ Horizontal Position or Vertical
Position to adjust the horizontal or vertical position of the
image.
“No Connection, Check Signal Cable” displays on screen.
Cause
Solution
Monitor video cable is disconnected.
Connect the video cable between the monitor and computer.
CAUTION: Ensure that the computer power is off while
connecting the video cable.
“Out of Range” displays on screen.
Cause
Solution
Video resolution and refresh rate are set higher than what
the monitor supports.
Restart the computer and enter Safe Mode. Change the
settings to a supported setting then restart the computer so
that the new settings take effect.
152 Chapter 8 Troubleshooting Without Diagnostics
Vibrating or rattling noise coming from inside a CRT monitor when powered on.
Cause
Solution
Monitor degaussing coil has been activated.
None. It is normal for the degaussing coil to be activated
when the monitor is powered on.
Clicking noise coming from inside a CRT monitor.
Cause
Solution
Electronic relays have been activated inside the monitor.
None. It is normal for some monitors to make a clicking noise
when turned on and off, when going in and out of standby
mode, and when changing resolutions.
High pitched noise coming from inside a flat panel monitor.
Cause
Solution
Brightness and/or contrast settings are too high.
Lower brightness and/or contrast settings.
Fuzzy focus; streaking, ghosting, or shadowing effects; horizontal scrolling lines; faint vertical bars; or unable to
center the picture on the screen (flat panel monitors using an analog VGA input connection only).
Cause
Solution
Flat panel monitor’s internal digital conversion circuits may
be unable to correctly interpret the output synchronization of
the graphics card.
1.
Select the monitor’s Auto-Adjustment option in the
monitor’s on-screen display menu.
2.
Manually synchronize the Clock and Clock Phase onscreen display functions. To download a SoftPaq that
will assist you with the synchronization, go to the
following Web site, select the appropriate monitor, and
download either SP32347 or SP32202:
http://www.hp.com/support
1.
Reseat the graphics card.
2.
Replace the graphics card.
Graphics card is not seated properly or is bad.
Certain typed symbols do not appear correct.
Cause
Solution
The font you are using does not support that particular
symbol.
Use the Character Map to locate and select the appropriate
symbol. Click Start > All Programs > Accessories >
System Tools > Character Map. You can copy the symbol
from the Character Map into a document.
Solving Display Problems 153
Solving Audio Problems
If the computer has audio features and you encounter audio problems, see the common causes and
solutions listed in the following table.
Table 8-7 Solving Audio Problems
Sound cuts in and out.
Cause
Solution
Processor resources are being used by other open
applications.
Shut down all open processor-intensive applications.
Direct sound latency, common in many media player
applications.
In Windows XP only:
1.
From the Control Panel, select Sounds and Audio
Devices.
2.
On the Audio tab, select a device from the Sound
Playback list.
3.
Click the Advanced button and select the Performance
tab.
4.
Set the Hardware acceleration slider to None and the
Sample rate conversion quality slider to Good and
retest the audio.
5.
Set the Hardware acceleration slider to Full and the
Sample rate conversion quality slider to Best and
retest the audio.
Sound does not come out of the speaker or headphones.
Cause
Solution
Software volume control is turned down or muted.
Double-click the Speaker icon on the taskbar, then make
sure that Mute is not selected and use the volume slider to
adjust the volume.
Audio is hidden in Computer Setup.
Enable the audio in Computer Setup: Security >
Device Security > System Audio.
The external speakers are not turned on.
Turn on the external speakers.
The audio device may be connected to the wrong jack.
Ensure that the device is connected to the correct jack on the
computer. The speakers should be plugged into the rear lineout jack and the headphones should be plugged into the
front headphone jack.
External speakers plugged into the wrong audio jack on a
recently installed sound card.
See the sound card documentation for proper speaker
connection.
Digital CD audio is not enabled.
Enable digital CD audio. In the Device Manager, right-click
on the CD/DVD device and select Properties. Make sure
Enable digital CD audio for this CD-ROM device is
checked.
Headphones or devices connected to the line-out connector
mute the internal speaker.
Turn on and use headphones or external speakers, if
connected, or disconnect headphones or external speakers.
154 Chapter 8 Troubleshooting Without Diagnostics
Table 8-7 Solving Audio Problems (continued)
Sound does not come out of the speaker or headphones.
Cause
Solution
Computer is in standby mode.
Press the power button to resume from standby mode.
CAUTION: When attempting to resume from standby
mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.
Internal speaker is disabled in Computer Setup.
Enable the internal speaker in Computer Setup. Select
Advanced > Device Options > Internal Speaker.
The application is set to use a different audio device than
speakers.
Some graphics cards support audio over the DisplayPort
connection, so multiple audio devices may be listed in
Device Manager. Make sure the correct device is being
used.
Some applications can select which audio output device is
used.
Make sure the application has selected the correct audio
device.
The operating system controls may be set to use a different
audio device as the default output device than what is
expected.
Set the operating system to use the correct audio device.
Sound from headphones is not clear or muffled.
Cause
Solution
Headphones are plugged into the rear audio output
connector. The rear audio output connector is for powered
audio devices and is not designed for headphone use.
Plug the headphones into the headphone connector on the
front of the computer.
Computer appears to be locked up while recording audio.
Cause
Solution
The hard disk may be full.
Before recording, make sure there is enough free space on
the hard disk. You can also try recording the audio file in a
compressed format.
Line-in jack is not functioning properly.
Cause
Solution
Jack has been reconfigured in the audio driver or application
software.
In the audio driver or application software, reconfigure the
jack or set the jack to its default value.
Solving Audio Problems 155
There is no sound or sound volume is too low.
Cause
Solution
The application is set to use a different audio device than
speakers.
Some graphics cards support audio over the DisplayPort
connection, so multiple audio devices may be listed in
Device Manager. Make sure the correct device is being
used.
Some applications can select which audio output device is
used.
Make sure the application has selected the correct audio
device.
The operating system controls may be set to use a different
audio device as the default output device than what is
expected.
Set the operating system to use the correct audio device.
Solving Printer Problems
If you encounter printer problems, see the documentation that came with the printer and to the
common causes and solutions listed in the following table.
Table 8-8 Solving Printer Problems
Printer will not print.
Cause
Solution
Printer is not turned on and online.
Turn the printer on and make sure it is online.
The correct printer drivers for the application are not
installed.
1.
Install the correct printer driver for the application.
2.
Try printing using the MS-DOS command:
DIR C:\ > [printer port]
where [printer port] is the address of the printer being
used. If the printer works, reload the printer driver.
If you are on a network, you may not have made the
connection to the printer.
Make the proper network connections to the printer.
Printer may have failed.
Run printer self-test.
Printer will not turn on.
Cause
Solution
The cables may not be connected properly.
Reconnect all cables and check the power cord and
electrical outlet.
Printer prints garbled information.
Cause
Solution
The correct printer driver for the application is not installed.
Install the correct printer driver for the application.
156 Chapter 8 Troubleshooting Without Diagnostics
Table 8-8 Solving Printer Problems (continued)
Printer prints garbled information.
Cause
Solution
The cables may not be connected properly.
Reconnect all cables.
Printer memory may be overloaded.
Reset the printer by turning it off for one minute, then turn it
back on.
Printer is offline.
Cause
Solution
The printer may be out of paper.
Check the paper tray and refill it if it is empty. Select online.
Solving Printer Problems 157
Solving Keyboard and Mouse Problems
If you encounter keyboard or mouse problems, see the documentation that came with the equipment
and to the common causes and solutions listed in the following table.
Table 8-9 Solving Keyboard Problems
Keyboard commands and typing are not recognized by the computer.
Cause
Solution
Keyboard connector is not properly connected.
1.
On the Windows XP Desktop, click Start > Shut Down.
On the Windows 7 Desktop, click Start, click the arrow
on the lower right corner of the Start menu, then select
Shut Down.
2.
After the shutdown is complete, reconnect the keyboard
to the back of the computer and restart the computer.
Program in use has stopped responding to commands.
Shut down your computer using the mouse and then restart
the computer.
Keyboard needs repairs.
See the Worldwide Limited Warranty for terms and
conditions.
Computer is in standby mode.
Press the power button to resume from standby mode.
CAUTION: When attempting to resume from standby
mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.
Cursor will not move using the arrow keys on the keypad.
Cause
Solution
The Num Lock key may be on.
Press the Num Lock key. The Num Lock light should not be
on if you want to use the arrow keys. The Num Lock key can
be disabled (or enabled) in Computer Setup.
Table 8-10 Solving Mouse Problems
Mouse does not respond to movement or is too slow.
Cause
Solution
Mouse connector is not properly plugged into the back of the
computer.
Shut down the computer using the keyboard.
158 Chapter 8 Troubleshooting Without Diagnostics
1.
Press the Ctrl and Esc keys at the same time (or press
the Windows logo key) to display the Start menu.
2.
Use the arrow keys to select Shut Down and then
press the Enter key.
3.
After the shutdown is complete, plug the mouse
connector into the back of the computer (or the
keyboard) and restart.
Table 8-10 Solving Mouse Problems (continued)
Mouse does not respond to movement or is too slow.
Cause
Solution
Program in use has stopped responding to commands.
Shut down the computer using the keyboard then restart the
computer.
Mouse may need cleaning.
Remove the roller ball cover on the mouse and clean the
internal components.
Mouse may need repair.
See the Worldwide Limited Warranty for terms and
conditions.
Computer is in standby mode.
Press the power button to resume from standby mode.
CAUTION: When attempting to resume from standby
mode, do not hold down the power button for more than four
seconds. Otherwise, the computer will shut down and you
will lose any unsaved data.
Mouse will only move vertically, horizontally, or movement is jerky.
Cause
Solution
Mouse roller ball or the rotating encoder shafts that make
contact with the ball are dirty.
Remove roller ball cover from the bottom of the mouse and
clean the internal components with a mouse cleaning kit
available from most computer stores.
A wireless keyboard/mouse is not working correctly. Symptoms include lagging mouse movement, jumpy mouse/
keyboard, or no function of mouse/keyboard and external drive.
Cause
Solution
If your computer is equipped with USB 3.0 ports, connected
USB 3.0 devices can interfere with the wireless keyboard
USB receiver.
Connect the wireless keyboard USB receiver to a USB 2.0
port that is separated from ports with USB 3.0 devices. If you
still experience interference, you may have to place the
connectors farther apart using an external USB hub.
Solving Keyboard and Mouse Problems 159
Solving Hardware Installation Problems
You may need to reconfigure the computer when you add or remove hardware, such as an additional
drive or expansion card. If you install a plug and play device, Windows automatically recognizes the
device and configures the computer. If you install a non–plug and play device, you must reconfigure
the computer after completing installation of the new hardware. In Windows, use the Add Hardware
Wizard and follow the instructions that appear on the screen.
WARNING! When the computer is plugged into an AC power source, voltage is always applied to
the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.
Table 8-11 Solving Hardware Installation Problems
A new device is not recognized as part of the system.
Cause
Solution
Device is not seated or connected properly.
Ensure that the device is properly and securely connected
and that pins in the connector are not bent down.
Cable(s) of new external device are loose or power cables
are unplugged.
Ensure that all cables are properly and securely connected
and that pins in the cable or connector are not bent down.
Power switch of new external device is not turned on.
Turn off the computer, turn on the external device, then turn
on the computer to integrate the device with the computer
system.
When the system advised you of changes to the
configuration, you did not accept them.
Reboot the computer and follow the instructions for
accepting the changes.
A plug and play board may not automatically configure when
added if the default configuration conflicts with other devices.
Use Windows Device Manager to deselect the automatic
settings for the board and choose a basic configuration that
does not cause a resource conflict. You can also use
Computer Setup to reconfigure or disable devices to resolve
the resource conflict.
USB ports on the computer are disabled in Computer Setup.
Run the Computer Setup utility and ensure that Device
available is selected for appropriate USB ports under
Security > USB Security.
Computer will not start.
Cause
Solution
Wrong memory modules were used in the upgrade or
memory modules were installed in the wrong location.
1.
Review the documentation that came with the system to
determine if you are using the correct memory modules
and to verify the proper installation.
NOTE: DIMM1 or XMM1 must always be installed. On
all computers expect the USDT, DIMM1 must be
installed before DIMM2, and DIMM3 must be installed
before DIMM4.
160 Chapter 8 Troubleshooting Without Diagnostics
2.
Observe the beeps and LED lights on the front of the
computer. Beeps and flashing LEDs are codes for
specific problems.
3.
If you still cannot resolve the issue, contact Customer
Support.
Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps
five times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Memory is installed incorrectly or is bad.
CAUTION: To avoid damage to the DIMMs or the system
board, you must unplug the computer power cord before
attempting to reseat, install, or remove a DIMM module.
1.
Reseat DIMMs. Power on the system.
2.
Replace DIMMs one at a time to isolate the faulty
module.
NOTE: DIMM1 or XMM1 must always be installed. On
all computers expect the USDT, DIMM1 must be
installed before DIMM2, and DIMM3 must be installed
before DIMM4
3.
Replace third-party memory with HP memory.
4.
Replace the system board.
Power LED flashes Red six times, once every second, followed by a two second pause, and the computer beeps six
times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Graphics card is not seated properly or is bad, or system
board is bad.
For systems with a graphics card:
1.
Reseat the graphics card. Power on the system.
2.
Replace the graphics card.
3.
Replace the system board.
For systems with integrated graphics, replace the system
board.
Power LED flashes Red ten times, once every second, followed by a two second pause, and the computer beeps ten
times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Bad option card.
1.
Check each option card by removing the cards one at
time (if multiple cards), then power on the system to see
if fault goes away.
2.
Once bad card is identified, remove and replace bad
option card.
3.
Replace the system board.
Solving Network Problems
Some common causes and solutions for network problems are listed in the following table. These
guidelines do not discuss the process of debugging the network cabling.
Solving Network Problems 161
Table 8-12 Solving Network Problems
Wake-on-LAN feature is not functioning.
Cause
Solution
S5 Maximum Power Saving feature is enabled.
Disable the S5 Maximum Power Saving option in Computer
Setup. Select Power > Hardware Power Management > S5
Maximum Power Saving.
S5 Wake on LAN is disabled.
: Enable the S5 Wake on LAN option in Computer Setup.
Select Advanced > Device Options > S5 Wake on LAN.
Wake-on-LAN is not enabled.
To enable Wake-on-LAN in Windows XP:
1.
Select Start > Control Panel.
2.
Double-click Network Connections.
3.
Double-click Local Area Connection.
4.
Click Properties.
5.
Click Configure.
6.
Click the Power Management tab, then select the
check box to Allow this device to bring the computer
out of standby.
To enable Wake-on-LAN in Windows 7:
1.
Select Start > Control Panel.
2.
Under Network and Internet, select View network
status and tasks.
3.
Click Local Area Connection.
4.
Click the Properties button.
5.
Click the Configure button.
6.
Click the Power Management tab, then select the
check box to Allow this device to wake the computer.
Network driver does not detect network controller.
Cause
Solution
Network controller is disabled.
1.
Run Computer Setup and enable network controller.
2.
Enable the network controller in the operating system
via Device Manager.
Incorrect network driver.
162 Chapter 8 Troubleshooting Without Diagnostics
Check the network controller documentation for the correct
driver or obtain the latest driver from the manufacturer’s Web
site.
Network status link light never flashes.
NOTE: The network status light is supposed to flash when there is network activity.
Cause
Solution
No active network is detected.
Check cabling and network equipment for proper connection.
Network controller is not set up properly.
Check for the device status within Windows, such as Device
Manager for driver load and the Network Connections applet
within Windows for link status.
Network controller is disabled.
1.
Run Computer Setup and enable network controller.
2.
Enable the network controller in the operating system
via Device Manager.
Network driver is not properly loaded.
Reinstall network drivers.
System cannot autosense the network.
Disable auto-sensing capabilities and force the system into
the correct operating mode.
Diagnostics reports a failure.
Cause
Solution
The cable is not securely connected.
Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.
The cable is attached to the incorrect connector.
Ensure that the cable is attached to the correct connector.
There is a problem with the cable or a device at the other
end of the cable.
Ensure that the cable and device at the other end are
operating correctly.
Network controller interrupt is shared with an expansion
board.
Under the Computer Setup Advanced menu, change the
resource settings for the board.
The network controller is defective.
Contact an authorized service provider.
Diagnostics passes, but the computer does not communicate with the network.
Cause
Solution
Network drivers are not loaded, or driver parameters do not
match current configuration.
Make sure the network drivers are loaded and that the driver
parameters match the configuration of the network controller.
Make sure the correct network client and protocol is installed.
The network controller is not configured for this computer.
Select the Network icon in the Control Panel and configure
the network controller.
Network controller stopped working when an expansion board was added to the computer.
Cause
Solution
Network controller interrupt is shared with an expansion
board.
Under the Computer Setup Advanced menu, change the
resource settings for the board.
Solving Network Problems 163
Table 8-12 Solving Network Problems (continued)
Network controller stopped working when an expansion board was added to the computer.
Cause
Solution
The network controller requires drivers.
Verify that the drivers were not accidentally deleted when the
drivers for a new expansion board were installed.
The expansion board installed is a network card (NIC) and
conflicts with the embedded NIC.
Under the Computer Setup Advanced menu, change the
resource settings for the board.
Network controller stops working without apparent cause.
Cause
Solution
The files containing the network drivers are corrupted.
Reinstall the network drivers, using the Recovery Disc Set
created from the hard drive's Recovery Partition.
The cable is not securely connected.
Ensure that the cable is securely attached to the network
connector and that the other end of the cable is securely
attached to the correct device.
The network controller is defective.
Contact an authorized service provider.
New network card will not boot.
Cause
Solution
New network card may be defective or may not meet
industry-standard specifications.
Install a working, industry-standard NIC, or change the boot
sequence to boot from another source.
Cannot connect to network server when attempting Remote System Installation.
Cause
Solution
The network controller is not configured properly.
Verify Network Connectivity, that a DHCP Server is present,
and that the Remote System Installation Server contains the
NIC drivers for your NIC.
System setup utility reports unprogrammed EEPROM.
Cause
Solution
Unprogrammed EEPROM.
Contact an authorized service provider.
Solving Memory Problems
If you encounter memory problems, some common causes and solutions are listed in the following
table.
164 Chapter 8 Troubleshooting Without Diagnostics
CAUTION: Power may still be supplied to the DIMMs when the computer is turned off (depending
on the Management Engine (ME) settings). To avoid damage to the DIMMs or the system board, you
must unplug the computer power cord before attempting to reseat, install, or remove a DIMM module.
For those systems that support ECC memory, HP does not support mixing ECC and non-ECC
memory. Otherwise, the computer will not boot the operating system.
NOTE: The memory count will be affected by configurations with the Management Engine (ME)
enabled. The ME uses 8MB of system memory in single channel mode or 16MB of memory in dualchannel mode to download, decompress, and execute the ME firmware for Out-of-Band (OOB), thirdparty data storage, and other management functions.
Table 8-13 Solving Memory Problems
System will not boot or does not function properly after installing additional memory modules.
Cause
Solution
A memory module is not installed in the DIMM1 or XMM1
socket.
Ensure that a memory module is installed in the DIMM1 or
XMM1 socket on the system board. This socket must be
populated with a memory module.
Memory module is not the correct type or speed grade for
the system or the new memory module is not seated
properly.
Replace module with the correct industry-standard device for
the computer. On some models, ECC and non-ECC memory
modules cannot be mixed.
Out of memory error.
Cause
Solution
Memory configuration may not be set up correctly.
Use the Device Manager to check memory configuration.
You have run out of memory to run the application.
Check the application documentation to determine the
memory requirements.
Memory count during POST is wrong.
Cause
Solution
The memory modules may not be installed correctly.
Check that the memory modules have been installed
correctly and that proper modules are used.
Integrated graphics may use system memory.
No action required.
Insufficient memory error during operation.
Cause
Solution
Too many Terminate and Stay Resident programs (TSRs)
are installed.
Delete any TSRs that you do not need.
You have run out of memory for the application.
Check the memory requirements for the application or add
more memory to the computer.
Solving Memory Problems 165
Power LED flashes Red five times, once every second, followed by a two second pause, and the computer beeps
five times. (Beeps stop after fifth iteration but LEDs continue flashing.)
Cause
Solution
Memory is installed incorrectly or is bad.
1.
Reseat DIMMs. Power on the system.
2.
Replace DIMMs one at a time to isolate the faulty
module.
3.
Replace third-party memory with HP memory.
4.
Replace the system board.
Solving Processor Problems
If you encounter processor problems, common causes and solutions are listed in the following table.
Table 8-14 Solving Processor Problems
Poor performance is experienced.
Cause
Solution
Processor is hot.
1.
Make sure the airflow to the computer is not blocked.
2.
Make sure the fans are connected and working properly
(some fans only operate when needed).
3.
Make sure the processor heat sink is installed properly.
Power LED flashes Red three times, once every second, followed by a two second pause.
Cause
Solution
Processor is not seated properly or not installed.
1.
Check to see that the processor is present.
2.
Reseat the processor.
Power LED flashes Red eleven times, once every second, followed by a two second pause.
Cause
Solution
The current processor does not support a feature previously
enabled on this system.
1.
Install a TXT capable processor.
2.
Disable TXT in the Computer Setup (F10) utility.
3.
Reinstall the original processor.
Solving CD-ROM and DVD Problems
If you encounter CD-ROM or DVD problems, see the common causes and solutions listed in the
following table or to the documentation that came with the optional device.
166 Chapter 8 Troubleshooting Without Diagnostics
Table 8-15 Solving CD-ROM and DVD Problems
System will not boot from CD-ROM or DVD drive.
Cause
Solution
The device is attached to a SATA port that has been hidden
in the Computer Setup utility.
Run the Computer Setup utility and ensure Device Available
is selected for the device's SATA port in Security > Device
Security.
Removable Media Boot is disabled in the Computer Setup
utility.
Run the Computer Setup utility and enable booting to
removable media in Storage > Storage Options. Ensure
CD-ROM is enabled in Storage > Boot Order.
Network Server Mode is enabled in Computer Setup.
Run the Computer Setup utility and disable Network Server
Mode in Security > Password Options.
Non-bootable CD in drive.
Try a bootable CD in the drive.
Boot order not correct.
Run the Computer Setup utility and change boot sequence in
Storage > Boot Order.
Drive not found (identified).
Cause
Solution
Cable could be loose.
Check cable connections.
The system may not have automatically recognized a newly
installed device.
See reconfiguration directions in the Solving Hardware
Installation Problems on page 160 section. If the system still
does not recognize the new device, check to see if the
device is listed within Computer Setup. If it is listed, the
probable cause is a driver problem. If it is not listed, the
probable cause is a hardware problem.
If this is a newly installed drive, run the Computer Setup
utility and try adding a POST delay under Advanced >
Power-On Options.
The device is attached to a SATA port that has been hidden
in Computer Setup.
Run the Computer Setup utility and ensure Device Available
is selected for the device's SATA port in Security > Device
Security.
Drive responds slowly immediately after power-up.
Run Computer Setup and increase the POST Delay in
Advanced > Power-On Options.
CD-ROM or DVD devices are not detected or driver is not loaded.
Cause
Solution
Drive is not connected properly or not properly configured.
See the documentation that came with the optional device.
Movie will not play in the DVD drive.
Cause
Solution
Movie may be regionalized for a different country.
See the documentation that came with the DVD drive.
Decoder software is not installed.
Install decoder software.
Solving CD-ROM and DVD Problems 167
Table 8-15 Solving CD-ROM and DVD Problems (continued)
Movie will not play in the DVD drive.
Cause
Solution
Damaged media.
Replace media.
Movie rating locked out by parental lock.
Use DVD software to remove parental lock.
Media installed upside down.
Reinstall media.
Cannot eject compact disc (tray-load unit).
Cause
Solution
Disc not properly seated in the drive.
Turn off the computer and insert a thin metal rod into the
emergency eject hole and push firmly. Slowly pull the tray
out from the drive until the tray is fully extended, then remove
the disc.
CD-ROM, CD-RW, DVD-ROM, or DVD-R/RW drive cannot read a disc or takes too long to start.
Cause
Solution
Media has been inserted upside down.
Re-insert the media with the label facing up.
The DVD-ROM drive takes longer to start because it has to
determine the type of media played, such as audio or video.
Wait at least 30 seconds to let the DVD-ROM drive
determine the type of media being played. If the disc still
does not start, read the other solutions listed for this topic.
CD or DVD disc is dirty.
Clean CD or DVD with a CD cleaning kit, available from most
computer stores.
Windows does not detect the CD-ROM or DVD-ROM drive.
1.
Use Device Manager to remove or uninstall the device.
2.
Restart the computer and let Windows detect the CD or
DVD driver.
Recording or copying CDs is difficult or impossible.
Cause
Solution
Wrong or poor quality media type.
1.
Try using a slower speed when recording.
2.
Verify that you are using the correct media for the drive.
3.
Try a different brand of media. Quality varies widely
between manufacturers.
USDT computer boots too slow after removing a CD-ROM or DVD drive.
Cause
Solution
The system is searching for the drive during boot because
the drive cable is still attached to the system board.
Disconnect the drive cable from the system board.
168 Chapter 8 Troubleshooting Without Diagnostics
Solving USB Flash Drive Problems
If you encounter USB flash drive problems, common causes and solutions are listed in the following
table.
Table 8-16 Solving USB Flash Drive Problems
USB flash drive is not seen as a drive letter in Windows.
Cause
Solution
The drive letter after the last physical drive is not available.
Change the default drive letter for the flash drive in Windows.
USB flash drive not found (identified).
Cause
Solution
The device is attached to a USB port that has been hidden in
Computer Setup.
Run the Computer Setup utility and ensure that “Device
available” is selected for “Front USB Ports” and “Rear USB
Ports” under Security > Device Security.
The device was not properly seated before power-up.
Ensure the device is fully inserted into the USB port before
applying power to the system
System will not boot from USB flash drive.
Cause
Solution
Boot order is not correct.
Run the Computer Setup utility and change boot sequence in
Storage > Boot Order.
Removable Media Boot is disabled in the Computer Setup
utility.
Run the Computer Setup utility and enable booting to
removable media in Storage > Storage Options. Ensure
USB is enabled in Storage > Boot Order.
The computer boots to DOS after making a bootable flash drive.
Cause
Solution
Flash drive is bootable.
Install the flash drive only after the operating system boots.
Solving USB Flash Drive Problems 169
Solving Front Panel Component Problems
If you encounter problems with devices connected to the front panel, refer to the common causes and
solutions listed in the following table.
Table 8-17 Solving Front Panel Component Problems
A USB device, headphone, or microphone is not recognized by the computer.
Cause
Solution
Device is not properly connected.
1.
Turn off the computer.
2.
Reconnect the device to the front of the computer and
restart the computer.
The device does not have power.
If the USB device requires AC power, be sure one end is
connected to the device and one end is connected to a live
outlet.
The correct device driver is not installed.
1.
Install the correct driver for the device.
2.
You might need to reboot the computer.
1.
If possible, replace the cable.
2.
Restart the computer.
1.
Replace the device.
2.
Restart the computer.
The cable from the device to the computer does not work.
The device is not working.
USB ports on the computer are disabled in Computer Setup.
Run the Computer Setup utility and ensure that Device
available is selected for appropriate USB ports under
Security > USB Security.
Solving Internet Access Problems
If you encounter Internet access problems, consult your Internet Service Provider (ISP) or refer to the
common causes and solutions listed in the following table.
Table 8-18 Solving Internet Access Problems
Unable to connect to the Internet.
Cause
Solution
Internet Service Provider (ISP) account is not set up
properly.
Verify Internet settings or contact your ISP for assistance.
Modem is not set up properly.
Reconnect the modem. Verify the connections are correct
using the quick setup documentation.
Web browser is not set up properly.
Verify that the Web browser is installed and set up to work
with your ISP.
Cable/DSL modem is not plugged in.
Plug in cable/DSL modem. You should see a “power” LED
light on the front of the cable/DSL modem.
170 Chapter 8 Troubleshooting Without Diagnostics
Table 8-18 Solving Internet Access Problems (continued)
Unable to connect to the Internet.
Cause
Solution
Cable/DSL service is not available or has been interrupted
due to bad weather.
Try connecting to the Internet at a later time or contact your
ISP. (If the cable/DSL service is connected, the “cable” LED
light on the front of the cable/DSL modem will be on.)
The CAT5 UTP cable is disconnected.
Connect the CAT5 UTP cable between the cable modem
and the computers’s RJ-45 connector. (If the connection is
good, the “PC” LED light on the front of the cable/DSL
modem will be on.)
IP address is not configured properly.
Contact your ISP for the correct IP address.
Cookies are corrupted. (A “cookie” is a small piece of
information that a Web server can store temporarily with the
Web browser. This is useful for having the browser
remember some specific information that the Web server can
later retrieve.)
Windows 7
1.
Select Start > Control Panel.
2.
Click Network and Internet.
3.
Click Internet Options.
4.
In the Browsing history section on the General tab,
click the Delete button.
5.
Select the Cookies check box and click the Delete
button.
Windows XP
1.
Select Start > Control Panel.
2.
Double-click Internet Options.
3.
On the General tab, click the Delete Cookies button.
Cannot automatically launch Internet programs.
Cause
Solution
You must log on to your ISP before some programs will start.
Log on to your ISP and launch the desired program.
Solving Internet Access Problems 171
Internet takes too long to download Web sites.
Cause
Solution
Modem is not set up properly.
Verify that the modem is connected and communicating
properly.
Windows 7
1.
Select Start > Control Panel.
2.
Click on Hardware and Sound.
3.
Click on Device Manager.
4.
Double-click Modems.
5.
Double-click Agere Systems PCI-SV92PP Soft
Modem.
6.
On the General tab, click Diagnostics.
7.
Click Query Modem. A “Success” response indicates
the modem is connected and working properly.
Windows XP
172 Chapter 8 Troubleshooting Without Diagnostics
1.
Select Start > Control Panel.
2.
Double-click System.
3.
Click the Hardware tab.
4.
In the Device Manager area, click the Device Manager
button.
5.
Double-click Modems.
6.
Double-click Agere Systems PCI-SV92PP Soft
Modem.
7.
On the General tab, click Diagnostics.
8.
Click Query Modem. A “Success” response indicates
the modem is connected and working properly.
Solving Software Problems
Most software problems occur as a result of the following:
●
The application was not installed or configured correctly.
●
There is insufficient memory available to run the application.
●
There is a conflict between applications.
●
Be sure that all the needed device drivers have been installed.
●
If you have installed an operating system other than the factory-installed operating system,
check to be sure it is supported on the system.
If you encounter software problems, see the applicable solutions listed in the following table.
Table 8-19 Solving Software Problems
Computer will not continue and no HP logo screen has appeared.
Cause
Solution
POST error has occurred.
Observe the beeps and LED lights on the front of the
computer. See Appendix A, POST Error Messages
on page 175 to determine possible causes.
See the Restore Kit or the Worldwide Limited Warranty for
terms and conditions.
Computer will not continue after HP logo screen has appeared.
Cause
Solution
System files may be damaged.
Use recovery diskette to scan hard drive for errors.
“Illegal Operation has Occurred” error message is displayed.
Cause
Solution
Software being used is not Microsoft-certified for your
version of Windows.
Verify that the software is certified by Microsoft for your
version of Windows (see program packaging for this
information).
Configuration files are corrupt.
If possible, save all data, close all programs, and restart the
computer.
Solving Software Problems 173
Contacting Customer Support
For help and service, contact an authorized reseller or dealer. To locate a reseller or dealer near you,
visit http://www.hp.com.
NOTE: If you take the computer to an authorized reseller, dealer, or service provider for service,
remember to provide the setup and power-on passwords if they are set.
Refer to the number listed in the warranty or in the Support Telephone Numbers guide for technical
assistance.
174 Chapter 8 Troubleshooting Without Diagnostics
9
POST Error Messages
This appendix lists the error codes, error messages, and the various indicator light and audible
sequences that you may encounter during Power-On Self-Test (POST) or computer restart, the
probable source of the problem, and steps you can take to resolve the error condition.
POST Message Disabled suppresses most system messages during POST, such as memory count
and non-error text messages. If a POST error occurs, the screen will display the error message. To
manually switch to the POST Messages Enabled mode during POST, press any key (except F10,
F11, or F12). The default mode is POST Message Disabled.
The speed at which the computer loads the operating system and the extent to which it is tested are
determined by the POST mode selection.
Quick Boot is a fast startup process that does not run all of the system level tests, such as the
memory test. Full Boot runs all of the ROM-based system tests and takes longer to complete.
Full Boot may also be enabled to run every 1 to 30 days on a regularly scheduled basis. To establish
the schedule, reconfigure the computer to the Full Boot Every x Days mode, using Computer Setup.
NOTE:
For more information on Computer Setup, see Computer Setup (F10) Utility on page 10.
175
POST Numeric Codes and Text Messages
This section covers those POST errors that have numeric codes associated with them. The section
also includes some text messages that may be encountered during POST.
NOTE:
The computer will beep once after a POST text message is displayed on the screen.
Table 9-1 Numeric Codes and Text Messages
Control panel message
Description
Recommended action
101-Option ROM Checksum Error
System ROM or expansion board option
ROM checksum.
1.
Verify the correct ROM.
2.
Flash the ROM if needed.
3.
If an expansion board was recently
added, remove it to see if the problem
remains.
4.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
5.
If the message disappears, there may
be a problem with the expansion card.
6.
Replace the system board.
1.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
2.
Remove expansion boards.
3.
Replace the system board.
1.
If a PCI expansion card was recently
added, remove it to see if the problem
remains.
2.
In Computer Setup, set Advanced >
Device Options > NIC PXE Option
ROM Download to DISABLE to
prevent PXE option ROM for the
internal NIC from being downloaded
during POST to free more memory for
an expansion card's option ROM.
Internal PXE option ROM is used for
booting from the NIC to a PXE server.
103-System Board Failure
110-Out of Memory Space for Option ROMs
162-System Options Not Set
DMA or timers.
Recently added PCI expansion card
contains an option ROM too large to
download during POST.
Configuration incorrect.
RTC (real-time clock) battery may need to
be replaced.
Run Computer Setup and check the
configuration in Advanced > Onboard
Devices.
Reset the date and time under Control
Panel. If the problem persists, replace the
RTC battery. See the Removal and
Replacement section for instructions on
installing a new battery, or contact an
authorized dealer or reseller for RTC battery
replacement.
176 Chapter 9 POST Error Messages
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
163-Time & Date Not Set
Invalid time or date in configuration
memory.
RTC (real-time clock) battery may need to
be replaced.
Reset the date and time under Control
Panel (Computer Setup can also be used).
If the problem persists, replace the RTC
battery. See the Removal and Replacement
section for instructions on installing a new
battery, or contact an authorized dealer or
reseller for RTC battery replacement.
163-Time & Date Not Set
CMOS jumper may not be properly
installed.
Check for proper placement of the CMOS
jumper if applicable.
164-MemorySize Error
Memory amount has changed since the last
boot (memory added or removed).
Press the F1 key to save the memory
changes.
164-MemorySize Error
Memory configuration incorrect.
1.
Run Computer Setup or Windows
utilities.
2.
Make sure the memory module(s) are
installed properly.
3.
If third-party memory has been added,
test using HP-only memory.
4.
Verify proper memory module type.
1.
Ensure memory modules are correctly
installed.
2.
Verify proper memory module type.
3.
Remove and replace the identified
faulty memory module(s).
4.
If the error persists after replacing
memory modules, replace the system
board.
A memory module in memory socket
identified in the error message is missing
critical SPD information, or is incompatible
with the chipset.
1.
Verify proper memory module type.
2.
Try another memory socket.
3.
Replace DIMM with a module
conforming to the SPD standard.
214-DIMM Configuration Warning
Populated DIMM Configuration is not
optimized.
Rearrange the DIMMs so that each channel
has the same amount of memory.
219-ECC Memory Module Detected ECC
Modules not supported on this Platform
Recently added memory module(s) support
ECC memory error correction.
1.
If additional memory was recently
added, remove it to see if the problem
remains.
2.
Check product documentation for
memory support information.
1.
Reconnect keyboard with computer
turned off.
2.
Check connector for bent or missing
pins.
3.
Ensure that none of the keys are
depressed.
4.
Replace keyboard.
201-Memory Error
213-Incompatible Memory Module in
Memory Socket(s) X, X, ...
301-Keyboard Error
RAM failure.
Keyboard failure.
POST Numeric Codes and Text Messages 177
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
303-Keyboard Controller Error
I/O board keyboard controller.
1.
Reconnect keyboard with computer
turned off.
2.
Replace the system board.
1.
Reconnect the keyboard with computer
turned off.
2.
Ensure that none of the keys are
depressed.
3.
Replace the keyboard.
4.
Replace the system board.
1.
Reseat the graphics card
(if applicable).
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
3.
Verify monitor is attached and turned
on.
4.
Replace the graphics card (if possible).
304-Keyboard or System Unit Error
501-Display Adapter Failure
Keyboard failure.
Graphics display controller.
510-Flash Screen Image Corrupted
Flash Screen image has errors.
Reflash the system ROM with the latest
BIOS image.
511-CPU, CPUA, or CPUB Fan not
Detected
CPU fan is not connected or may have
malfunctioned.
1.
Reseat CPU fan.
2.
Reseat fan cable.
3.
Replace CPU fan.
1.
Reseat chassis, rear chassis, or front
chassis fan.
2.
Reseat fan cable.
3.
Replace chassis, rear chassis, or front
chassis fan.
1.
Reseat front chassis fan.
2.
Reseat fan cable.
3.
Replace front chassis fan.
1.
Reseat CPU or chassis fan.
2.
Reseat fan cable.
3.
Replace CPU or chassis fan.
1.
Reseat power supply fan.
2.
Reseat fan cable.
3.
Replace power supply fan.
512-Chassis, Rear Chassis, or Front
Chassis Fan not Detected
513-Front Chassis fan not detected
514-CPU or Chassis Fan not Detected
515-Power Supply fan not detected
178 Chapter 9 POST Error Messages
Chassis, rear chassis, or front chassis fan is
not connected or may have malfunctioned.
Front chassis fan is not connected or may
have malfunctioned.
CPU or chassis fan is not connected or may
have malfunctioned.
Power supply fan is not connected or may
have malfunctioned.
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
601-Diskette Controller Error
Diskette controller circuitry or floppy drive
circuitry incorrect.
1.
Check and/or replace cables.
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
3.
Replace diskette drive.
4.
Replace the system board.
1.
Disconnect any other diskette
controller devices (tape drives).
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
605-Diskette Drive Type Error
Mismatch in drive type.
660-Display cache is detected unreliable
Integrated graphics controller display cache
is not working properly and will be disabled.
Replace system board if minimal graphics
degrading is an issue.
912-Computer Cover Has Been Removed
Since Last System Startup
Computer cover was removed since last
system startup.
No action required.
917-Front Audio Not Connected
Front audio harness has been detached or
unseated from motherboard.
Reconnect or replace front audio harness.
918-Front USB Not Connected
Front USB harness has been detached or
unseated from motherboard.
Reconnect or replace front USB harness.
921-Device in PCI Express slot failed to
initialize
There is an incompatibility/problem with this
device and the system or PCI Express Link
could not be retrained to an x1.
Try rebooting the system. If the error
reoccurs, the device may not work with this
system
1151-Serial Port A Address Conflict
Detected
Both external and internal serial ports are
assigned to COM1.
1.
Remove any serial port expansion
cards.
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
3.
Reconfigure card resources and/or run
Computer Setup or Windows utilities.
1.
Remove any serial port expansion
cards.
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
3.
Reconfigure card resources and/or run
Computer Setup or Windows utilities.
1.
Remove any serial port expansion
cards.
2.
Clear CMOS. (See Appendix B,
Password Security and Resetting
CMOS on page 188.)
3.
Reconfigure card resources and/or run
Computer Setup or Windows utilities.
1152-Serial Port B Address Conflict
Detected
1155-Serial Port Address Conflict Detected
Both external and internal serial ports are
assigned to COM2.
Both external and internal serial ports are
assigned to same IRQ.
POST Numeric Codes and Text Messages 179
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
1720-SMART Hard Drive Detects Imminent
Failure
Hard drive is about to fail. (Some hard
drives have a hard drive firmware patch that
will fix an erroneous error message.)
1.
Determine if hard drive is giving correct
error message. Enter Computer Setup
and run the Drive Protection System
test under Storage > DPS Self-test.
2.
Apply hard drive firmware patch
if applicable. (Available at
http://www.hp.com/support.)
3.
Back up contents and replace hard
drive.
1796-SATA Cabling Error
One or more SATA devices are improperly
attached. For optimal performance, the
SATA 0 and SATA 1 connectors must be
used before SATA 2 and SATA 3.
Ensure SATA connectors are used in
ascending order. For one device, use SATA
0. For two devices, use SATA 0 and SATA
1. For three devices, use SATA 0, SATA 1,
and SATA 2.
1797-SATA Drivelock is not supported in
RAID mode.
Drivelock is enabled on one or more SATA
hard drives, and they cannot be accessed
while the system is configured for RAID
mode.
Either remove the Drivelocked SATA device
or disable the Drivelock feature. To disable
the Drivelock feature, enter Computer
Setup, change Storage > Storage
Options > SATA Emulation to IDE, and
select File > Save Changes and Exit.
Reenter Computer Setup and select
Security > Drivelock Security. For each
listed Drivelock-capable SATA device,
ensure Drivelock is Disabled. Lastly,
change Storage > Storage Options >
SATA Emulation back to RAID and select
File > Save Changes and Exit.
1801-Microcode Patch Error
Processor is not supported by ROM BIOS.
1.
Upgrade BIOS to proper version.
2.
Change the processor.
1.
Reboot the computer.
2.
Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3.
If the memory configuration was
recently changed, unplug the
computer, restore the original memory
configuration, and reboot the
computer.
4.
If the error persists, replace the system
board.
2200-PMM Allocation Error during MEBx
Download
180 Chapter 9 POST Error Messages
Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
2201-MEBx Module did not checksum
correctly
Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
1.
Reboot the computer.
2.
Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3.
If the memory configuration was
recently changed, unplug the power
cord, restore the original memory
configuration, and reboot the
computer.
4.
If the error persists, replace the system
board.
1.
Reboot the computer.
2.
Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3.
If the memory configuration was
recently changed, unplug the power
cord, restore the original memory
configuration, and reboot the
computer.
4.
If the error persists, replace the system
board.
1.
Reboot the computer.
2.
Unplug the power cord, re-seat the
memory modules, and reboot the
computer.
3.
If the memory configuration was
recently changed, unplug the power
cord, restore the original memory
configuration, and reboot the
computer.
4.
If the error persists, replace the system
board.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version.
3.
If the error still persists, replace the
system board.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version.
3.
If the error still persists, replace the
system board.
2202-PMM Deallocation Error during MEBx
cleanup
2203-Setup error during MEBx execution
2204-Inventory error during MEBx execution
2205-Interface error during MEBx execution
Memory error during POST execution of the
Management Engine (ME) BIOS Extensions
option ROM.
MEBx selection or exit resulted in a setup
failure.
BIOS information passed to the MEBx
resulted in a failure.
MEBx operation experienced a hardware
error during communication with ME.
POST Numeric Codes and Text Messages 181
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
2211-Memory not configured correctly for
proper MEBx execution.
DIMM1 or XMM1 is not installed.
Make sure there is a memory module in the
black DIMM1 socket and that it is properly
seated.
2212-USB Key Provisioning failure writing to
device
USB device used for USB key provisioning
will not allow BIOS to update provision file
properly.
1.
Try a different USB key device for
provisioning.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
1.
Update to the latest ME firmware
version.
2.
If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.
3.
If the error still persists, replace the
system board.
1.
Recreate the provisioning file using
third party management console
software.
2.
If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.
Otherwise, update the ME firmware
version.
3.
If the error still persists, replace the
system board.
1.
Reboot the computer.
2.
If the error persists and system BIOS
has been recently updated, restore
previous system BIOS version.
Otherwise, update the ME firmware
version.
3.
If the error still persists, replace the
system board.
2217-ME Firmware Version request failure
2218-ME Firmware Version should be
updated
2219-USB Key Provisioning file has invalid
header identifier
2220-USB Key Provisioning file has
mismatch version
182 Chapter 9 POST Error Messages
ME firmware is not properly responding to
BIOS query for version information.
ME firmware must be updated to match
current functionality contained in the system
BIOS.
Provisioning file contained on the USB key
has been corrupted or is not a valid version
for the current ME firmware.
Provisioning file contained on the USB key
is not a valid version for the current ME
firmware.
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
2230-General error during MEBx execution
Error occurred during MEBx execution
which fails into the “General” grouping.
Status information displayed along with the
error provides further clarity into the failure.
MEBx handles transference of information
between the system BIOS and ME
firmware.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
Error occurred during MEBx execution
which fails into “ME” grouping.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
Special system configurations with reduced
ME firmware image require BIOS control of
ME firmware upgrading. A failure has
occurred after the ME firmware update
process in which the BIOS could not relock
the ME firmware region.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
Special system configurations with reduced
ME firmware image require BIOS control of
ME firmware upgrading. A failure has
occurred prior to the ME firmware update
process in which the BIOS could not unlock
the ME firmware region.
1.
Reboot the computer.
2.
If the error persists, update to the latest
BIOS version and ME firmware
version.
3.
If the error still persists, replace the
system board.
Electronic serial number is missing.
Enter the correct serial number in Computer
Setup.
2231-ME error during MEBx execution
2232-AMT error during MEBx execution
2233-HECI error during MEBx execution
2239-ME image lock failure
2240-ME image unlock failure
Invalid Electronic Serial Number
Error occurred during MEBx execution
which fails into “AMT” grouping.
Error occurred during MEBx execution
which fails into “MEI or HECI” grouping.
POST Numeric Codes and Text Messages 183
Table 9-1 Numeric Codes and Text Messages (continued)
Control panel message
Description
Recommended action
Network Server Mode Active and No
Keyboard Attached
Keyboard failure while Network Server
Mode enabled.
1.
Reconnect keyboard with computer
turned off.
2.
Check connector for bent or missing
pins.
3.
Ensure that none of the keys are
depressed.
4.
Replace keyboard.
Parity Check 2
Parity RAM failure.
Run Computer Setup and Diagnostic
utilities.
Interpreting POST Diagnostic Front Panel LEDs and
Audible Codes
This section covers the front panel LED codes as well as the audible codes that may occur before or
during POST that do not necessarily have an error code or text message associated with them.
WARNING! When the computer is plugged into an AC power source, voltage is always applied to
the system board. To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet and allow the internal system components to
cool before touching.
NOTE: If you see flashing LEDs on a PS/2 keyboard, look for flashing LEDs on the front panel of
the computer and refer to the following table to determine the front panel LED codes.
Recommended actions in the following table are listed in the order in which they should be
performed.
Not all diagnostic lights and audible codes are available on all models.
Table 9-2 Diagnostic Front Panel LEDs and Audible Codes
Activity
Beeps
Possible Cause
Recommended Action
Green Power LED On.
None
Computer on.
None
Green Power LED flashes
every two seconds.
None
Computer in Suspend to
RAM mode (some models
only) or normal Suspend
mode.
None required. Press any key or move the
mouse to wake the computer.
184 Chapter 9 POST Error Messages
Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continued)
Activity
Beeps
Possible Cause
Recommended Action
Red Power LED flashes two
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
2
Processor thermal
protection activated:
1.
Ensure that the computer air vents are not
blocked and the processor cooling fan is
running.
2.
Open hood, press power button, and see if
the processor fan spins. If the processor fan
is not spinning, make sure the fan's cable is
plugged onto the system board header.
3.
If fan is plugged in, but is not spinning, then
replace heat sink/fan assembly.
4.
Contact an authorized reseller or service
provider.
Processor not installed
(not an indicator of bad
processor).
1.
Check to see that the processor is present.
2.
Reseat the processor.
Power failure (power
supply is overloaded).
1.
Open the hood and ensure the 4 or 6-wire
power supply cable is seated into the
connector on the system board.
2.
Check if a device is causing the problem by
removing ALL attached devices (such as
hard, diskette, or optical drives, and
expansion cards). Power on the system. If
the system enters the POST, then power off
and replace one device at a time and
repeat this procedure until failure occurs.
Replace the device that is causing the
failure. Continue adding devices one at a
time to ensure all devices are functioning
properly.
3.
Replace the power supply.
4.
Replace the system board.
A fan may be blocked or
not turning.
OR
The heat sink/fan
assembly is not properly
attached to the processor.
Red Power LED flashes three
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
3
Red Power LED flashes four
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
4
OR
The incorrect external
power supply adapter is
being used on the USDT.
OR
The USDT power supply adapter must be at
135W and use the Smart ID technology before
the system will power up. Replace the power
supply adapter with the HP-supplied USDT
power supply adapter.
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes 185
Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continued)
Activity
Beeps
Possible Cause
Recommended Action
Red Power LED flashes five
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
5
Pre-video memory error.
CAUTION: To avoid damage to the DIMMs or
the system board, you must unplug the computer
power cord before attempting to reseat, install, or
remove a DIMM module.
Red Power LED flashes six
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
6
Pre-video graphics error.
1.
Reseat DIMMs.
2.
Replace DIMMs one at a time to isolate the
faulty module.
3.
Replace third-party memory with HP
memory.
4.
Replace the system board.
For systems with a graphics card:
1.
Reseat the graphics card.
2.
Replace the graphics card.
3.
Replace the system board.
For systems with integrated graphics, replace
the system board.
Red Power LED flashes
seven times, once every
second, followed by a two
second pause. Beeps stop
after fifth iteration but LEDs
continue until problem is
solved.
7
System board failure
(ROM detected failure
prior to video).
Replace the system board.
Red Power LED flashes eight
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
8
Invalid ROM based on
bad checksum.
1.
Reflash the system ROM with the latest
BIOS image. See the “Boot Block
Emergency Recovery Mode” section of the
Desktop Management Guide for more
information.
2.
Replace the system board.
1.
Check that the voltage selector, located on
the rear of the power supply (some
models), is set to the appropriate voltage.
Proper voltage setting depends on your
region.
2.
Unplug the AC power cord from the
computer, wait 30 seconds, then plug the
power cord back in to the computer.
3.
Replace the system board.
4.
Replace the processor.
Red Power LED flashes nine
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
9
186 Chapter 9 POST Error Messages
System powers on but is
unable to boot.
Table 9-2 Diagnostic Front Panel LEDs and Audible Codes (continued)
Activity
Beeps
Possible Cause
Recommended Action
Red Power LED flashes ten
times, once every second,
followed by a two second
pause. Beeps stop after fifth
iteration but LEDs continue
until problem is solved.
10
Bad option card.
1.
Check each option card by removing the
card (one at a time if multiple cards), then
power on the system to see if fault goes
away.
2.
Once a bad card is identified, remove and
replace the bad option card.
3.
Replace the system board.
1.
Install a TXT capable processor.
2.
Disable TXT in the Computer Setup (F10)
utility.
3.
Reinstall the original processor.
Red Power LED flashes
eleven times, once every
second, followed by a two
second pause. Beeps stop
after fifth iteration but LEDs
continue until problem is
solved.
11
The current processor
does not support a
feature previously
enabled on this system.
System does not power on
and LEDs are not flashing.
None
System unable to power
on.
Press and hold the power button for less than 4
seconds. If the hard drive LED turns green, the
power button is working correctly. Try the
following:
1.
Check that the voltage selector (some
models), located on the rear of the power
supply, is set to the appropriate voltage.
Proper voltage setting depends on your
region.
2.
Replace the system board.
OR
Press and hold the power button for less than 4
seconds. If the hard drive LED does not turn on
green then:
1.
Check that the unit is plugged into a
working AC outlet.
2.
Open hood and check that the power button
harness is properly connected to the
system board.
3.
Check that both power supply cables are
properly connected to the system board.
4.
Check to see if the 5V_aux light on the
system board is turned on. If it is turned on,
then replace the power button harness. If
the problem persists, replace the system
board.
5.
If the 5V_aux light on the system board is
not turned on, remove the expansion cards
one at a time until the 5V_aux light on the
system board turns on. It the problem
persists, replace the power supply.
Interpreting POST Diagnostic Front Panel LEDs and Audible Codes 187
10 Password Security and Resetting
CMOS
This computer supports security password features, which can be established through the Computer
Setup Utilities menu.
This computer supports two security password features that are established through the Computer
Setup Utilities menu: setup password and power-on password. When you establish only a setup
password, any user can access all the information on the computer except Computer Setup. When
you establish only a power-on password, the power-on password is required to access Computer
Setup and any other information on the computer. When you establish both passwords, only the
setup password will give you access to Computer Setup.
When both passwords are set, the setup password can also be used in place of the power-on
password as an override to log in to the computer. This is a useful feature for a network administrator.
If you forget the password for the computer, you can clear that password so you can gain access to
the information on the computer by resetting the password jumper.
CAUTION: Pushing the CMOS button will reset CMOS values to factory defaults. It is important to
back up the computer CMOS settings before resetting them in case they are needed later. Back up is
easily done through Computer Setup. See Computer Setup (F10) Utility on page 10 for information on
backing up the CMOS settings.
188 Chapter 10 Password Security and Resetting CMOS
Resetting the Password Jumper
To disable the power-on or setup password features, or to clear the power-on or setup passwords,
complete the following steps:
1.
Shut down the operating system properly, then turn off the computer and any external devices,
and disconnect the power cord from the power outlet.
2.
With the power cord disconnected, press the power button again to drain the system of any
residual power.
WARNING! To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet, and allow the internal system
components to cool before touching.
CAUTION: When the computer is plugged in, the power supply always has voltage applied to
the system board even when the unit is turned off. Failure to disconnect the power cord can
result in damage to the system.
Static electricity can damage the electronic components of the computer or optional equipment.
Before beginning these procedures, ensure that you are discharged of static electricity by briefly
touching a grounded metal object. See the Safety & Regulatory Information guide for more
information.
3.
Remove the computer cover or access panel.
4.
Locate the header and jumper.
NOTE: The password jumper is green so that it can be easily identified. For assistance
locating the password jumper and other system board components, see the Illustrated Parts &
Service Map (IPSM). The IPSM can be downloaded from http://www.hp.com/support.
5.
Remove the jumper from pins 1 and 2. Place the jumper on either pin 1 or 2, but not both, so
that it does not get lost.
6.
Replace the computer cover or access panel.
7.
Reconnect the external equipment.
8.
Plug in the computer and turn on power. Allow the operating system to start. This clears the
current passwords and disables the password features.
9.
To establish new passwords, repeat steps 1 through 4, replace the password jumper on pins 1
and 2, then repeat steps 6 through 8. Establish the new passwords in Computer Setup.
Resetting the Password Jumper 189
Clearing and Resetting the CMOS
The computer’s configuration memory (CMOS) stores information about the computer’s configuration.
The CMOS button resets CMOS but does not clear the power-on and setup passwords.
Clearing CMOS will clear the Active Management Technology (AMT) settings in the Management
Engine BIOS Extension (MEBx), including the password. The password will default to “admin” and will
need to be reset. The AMT settings will also need to be reset. To access the MEBx, press Ctrl+P
during POST.
1.
Turn off the computer and any external devices, and disconnect the power cord from the power
outlet.
2.
Disconnect the keyboard, monitor, and any other external equipment connected to the computer.
WARNING! To reduce the risk of personal injury from electrical shock and/or hot surfaces, be
sure to disconnect the power cord from the wall outlet, and allow the internal system
components to cool before touching.
CAUTION: When the computer is plugged in, the power supply always has voltage applied to
the system board even when the unit is turned off. Failure to disconnect the power cord can
result in damage to the system.
Static electricity can damage the electronic components of the computer or optional equipment.
Before beginning these procedures, ensure that you are discharged of static electricity by briefly
touching a grounded metal object. See the Safety & Regulatory Information guide for more
information.
3.
Remove the computer cover or access panel.
CAUTION: Pushing the CMOS button will reset CMOS values to factory defaults. It is
important to back up the computer CMOS settings before resetting them in case they are
needed later. Back up is easily done through Computer Setup. See Computer Setup (F10) Utility
on page 10 for information on backing up the CMOS settings.
190 Chapter 10 Password Security and Resetting CMOS
4.
Locate, press, and hold the CMOS button in for five seconds.
NOTE: Make sure you have disconnected the AC power cord from the wall outlet. The CMOS
button will not clear CMOS if the power cord is connected.
Figure 10-1 CMOS button
NOTE: For assistance locating the CMOS button and other system board components, see the
Illustrated Parts & Service Map (IPSM).
5.
Replace the computer cover or access panel.
6.
Reconnect the external devices.
7.
Plug in the computer and turn on power.
NOTE: You will receive POST error messages after clearing CMOS and rebooting advising
you that configuration changes have occurred. Use Computer Setup to reset any special system
setups along with the date and time.
For instructions on Computer Setup, see Computer Setup (F10) Utility on page 10.
Clearing and Resetting the CMOS 191
11 Backup and Recovery
Windows 7 – Backup and Recovery
To protect your information, use Windows® Backup and Restore to back up individual files and
folders, back up your entire hard drive (select models only), create system repair discs (select models
only), or create system restore points. In case of system failure, you can use the backup files to
restore the contents of your computer.
Windows Backup and Restore provides the following options:
●
Creating a system repair disc (select models only)
●
Backing up individual files and folders
●
Creating a system image (select models only)
●
Scheduling automatic backups (select models only)
●
Creating system restore points
●
Recovering individual files
●
Restoring the computer to a previous state
●
Recovering information using recovery tools
NOTE:
For detailed instructions, perform a search for these topics in Help and Support.
NOTE: In case of system instability, HP recommends that you print the recovery procedures and
save them for later use.
Backing up your information
Recovery after a system failure is as complete as your most current backup. You should create
system repair discs (select models only) and your initial backup immediately after software setup. As
you add new software and data files, you should continue to back up your system on a regular basis
to maintain a reasonably current backup. The system repair discs (select models only) are used to
start up (boot) the computer and repair the operating system in case of system instability or failure.
Your initial and subsequent backups allow you to restore your data and settings if a failure occurs.
You can back up your information to an optional external hard drive, a network drive, or discs.
192 Chapter 11 Backup and Recovery
Note the following when backing up:
●
Store personal files in the Documents library, and back it up regularly.
●
Back up templates that are stored in their associated programs.
●
Save customized settings that appear in a window, toolbar, or menu bar by taking a screen shot
of your settings. The screen shot can be a time-saver if you have to reset your preferences.
To create a screen shot:
1.
Display the screen you want to save.
2.
Copy the screen image:
To copy only the active window, press alt+fn+prt sc.
To copy the entire screen, press fn+prt sc.
3.
Open a word-processing document, and then select Edit > Paste.
The screen image is added to the document.
4.
●
Save the document.
When backing up to discs, use any of the following types of discs (purchased separately): CD-R,
CD-RW, DVD+R, DVD+R DL, DVD-R, DVD-R DL, or DVD±RW. The discs you use will depend
on the type of optical drive installed in your computer.
NOTE: DVDs and DVDs with double-layer (DL) support store more information than CDs, so
using them for backup reduces the number of recovery discs required.
●
When backing up to discs, number each disc before inserting it into the optical drive of the
computer.
To create a backup using Backup and Restore, follow these steps:
NOTE:
Be sure that the computer is connected to AC power before you start the backup process.
NOTE: The backup process may take over an hour, depending on file size and the speed of the
computer.
1.
Select Start > All Programs > Maintenance > Backup and Restore.
2.
Follow the on-screen instructions to set up your backup, create a system image (select models
only), or create a system repair disc (select models only).
NOTE: Windows® includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
Windows 7 – Backup and Recovery 193
Performing a recovery
In case of system failure or instability, the computer provides the following tools to recover your files:
●
Windows recovery tools: You can use Windows Backup and Restore to recover information you
have previously backed up. You can also use Windows Startup Repair to fix problems that might
prevent Windows from starting correctly.
●
F11 recovery tools: You can use the F11 recovery tools to recover your original hard drive
image. The image includes the Windows operating system and software programs installed at
the factory.
NOTE: If you are unable to boot (start up) your computer and you cannot use the system repair
discs you previously created (select models only), you must purchase a Windows 7 operating system
DVD to reboot the computer and repair the operating system. For additional information, refer to the
“Using a Windows 7 operating system DVD (purchased separately)” section in this guide.
Using the Windows recovery tools
To recover information you previously backed up, follow these steps:
1.
Select Start > All Programs > Maintenance > Backup and Restore.
2.
Follow the on-screen instructions to recover your system settings, your computer (select models
only), or your files.
NOTE: Windows includes the User Account Control feature to improve the security of your
computer. You may be prompted for your permission or password for tasks such as installing
software, running utilities, or changing Windows settings. Refer to Help and Support for more
information.
To recover your information using Startup Repair, follow these steps:
CAUTION: All files you have created and any software installed on the computer are permanently
removed. When reformatting is complete, the recovery process restores the operating system, as well
as the drivers, software, and utilities from the backup used for recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the Windows partition and the HP Recovery partition.
To check for the Windows partition, select Start > Computer.
To check for the HP Recovery partition, select Start, right-click Computer, click Manage, and
then click Disk Management.
NOTE: If the Windows partition and the HP Recovery partition are not listed, you must recover
your operating system and programs using the System Recovery discs that you can obtain from
HP Support.
3.
If the Windows partition and the HP Recovery partition are listed, restart the computer, and then
press F8 before the Windows operating system loads.
4.
Select Repair Your Computer. The following options display: Startup Repair, System Restore,
System Image Recovery, Windows Memory Diagnostics, Command Prompt, Recovery
Manager.
194 Chapter 11 Backup and Recovery
5.
Select one of the first three listed tools to repair your computer.
6.
Follow the on-screen instructions.
NOTE: For additional information on recovering information using the Windows tools, perform a
search for these topics in Help and Support.
Using F11
CAUTION: Using F11 completely erases hard drive contents and reformats the hard drive. All files
you have created and any software installed on the computer are permanently removed. The F11
recovery tool reinstalls the operating system and HP programs and drivers that were installed at the
factory. Software not installed at the factory must be reinstalled.
If Windows 7 is not responding, but the computer is working, follow these steps to perform a System
Recovery.
1.
If possible, back up all personal files.
2.
If possible, check for the presence of the HP Recovery partition: select Start, right-click
Computer, click Manage, and then click Disk Management.
NOTE: If the Windows partition and the HP Recovery partition are not listed, you must recover
your operating system and programs using the System Recovery discs that you can obtain from
HP Support.
3.
Press the Power button to turn on the computer.
4.
As soon as you see the initial company logo screen appear, repeatedly press the F11 key on
your keyboard until the Windows is Loading Files… message appears on the screen.
5.
Under I need help immediately, tap System Recovery.
6.
If you are prompted to back up your files, and you have not done so, tap Back up your files
first (recommended), and then tap Next. Otherwise, tap Recover without backing up your
files, and then tap Next.
7.
System Recovery begins. After System Recovery is complete, tap Finish to restart the
computer.
Using a Windows 7 operating system DVD (purchased separately)
If you are unable to boot (start up) your computer and you cannot use the system repair discs you
previously created (select models only), you must use System Recovery discs that you can obtain
from HP Support to reboot the computer and repair the operating system. Make sure that your most
recent backup (stored on discs or on an external drive) is easily accessible.
CAUTION: All files you have created and any software installed on the computer are permanently
removed. When reformatting is complete, the recovery process helps you restore the operating
system, as well as drivers, software, and utilities.
To initiate recovery using a Windows 7 operating system DVD, follow these steps:
Windows 7 – Backup and Recovery 195
NOTE:
This process takes several minutes.
1.
If possible, back up all personal files.
2.
Restart the computer, and then insert the Windows 7 operating system DVD into the optical
drive before the Windows operating system loads.
3.
When prompted, press any keyboard key.
4.
Follow the on-screen instructions.
5.
Click Next.
6.
Select Repair your computer.
7.
Follow the on-screen instructions.
196 Chapter 11 Backup and Recovery
A
Battery Replacement
The battery that comes with the computer provides power to the real-time clock. When replacing the
battery, use a battery equivalent to the battery originally installed in the computer. The computer
comes with a 3-volt lithium coin cell battery.
WARNING! The computer contains an internal lithium manganese dioxide battery. There is a risk of
fire and burns if the battery is not handled properly. To reduce the risk of personal injury:
Do not attempt to recharge the battery.
Do not expose to temperatures higher than 60°C (140ºF).
Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water.
Replace the battery only with the HP spare designated for this product.
CAUTION: Before replacing the battery, it is important to back up the computer CMOS settings.
When the battery is removed or replaced, the CMOS settings will be cleared.
Static electricity can damage the electronic components of the computer or optional equipment.
Before beginning these procedures, ensure that you are discharged of static electricity by briefly
touching a grounded metal object.
NOTE: The lifetime of the lithium battery can be extended by plugging the computer into a live AC
wall socket. The lithium battery is only used when the computer is NOT connected to AC power.
HP encourages customers to recycle used electronic hardware, HP original print cartridges, and
rechargeable batteries. For more information about recycling programs, go to http://www.hp.com/
recycle.
1.
Remove/disengage any security devices that prohibit opening the computer.
2.
Remove all removable media, such as compact discs or USB flash drives, from the computer.
3.
Turn off the computer properly through the operating system, then turn off any external devices.
4.
Disconnect the power cord from the power outlet and disconnect any external devices.
CAUTION: Regardless of the power-on state, voltage is always present on the system board
as long as the system is plugged into an active AC outlet. You must disconnect the power cord
to avoid damage to the internal components of the computer.
5.
Remove the computer access panel.
6.
Locate the battery and battery holder on the system board.
NOTE: On some computer models, it may be necessary to remove an internal component to
gain access to the battery.
197
7.
Depending on the type of battery holder on the system board, complete the following instructions
to replace the battery.
Type 1
a.
Lift the battery out of its holder.
Figure A-1 Removing a Coin Cell Battery (Type 1)
b.
Slide the replacement battery into position, positive side up. The battery holder
automatically secures the battery in the proper position.
Type 2
a.
To release the battery from its holder, squeeze the metal clamp that extends above one
edge of the battery. When the battery pops up, lift it out (1).
b.
To insert the new battery, slide one edge of the replacement battery under the holder’s lip
with the positive side up. Push the other edge down until the clamp snaps over the other
edge of the battery (2).
Figure A-2 Removing and Replacing a Coin Cell Battery (Type 2)
Type 3
a.
Pull back on the clip (1) that is holding the battery in place, and remove the battery (2).
198 Appendix A Battery Replacement
b.
Insert the new battery and position the clip back into place.
Figure A-3 Removing a Coin Cell Battery (Type 3)
NOTE: After the battery has been replaced, use the following steps to complete this procedure.
8.
Replace the computer access panel.
9.
Plug in the computer and turn on power to the computer.
10. Reset the date and time, your passwords, and any special system setups using Computer
Setup.
11. Lock any security devices that were disengaged when the computer access panel was removed.
199
B
Removing and Replacing a Removable
3.5-inch SATA Hard Drive
Some models are equipped with a Removable SATA Hard Drive Enclosure in the 5.25-inch internal
drive bay. The hard drive is housed in a carrier that can be quickly and easily removed from the drive
bay. To remove and replace a drive in the carrier:
NOTE: Before you remove the old hard drive, be sure to back up the data from the old hard drive so
that you can transfer the data to the new hard drive.
1.
Unlock the hard drive carrier with the key provided and slide the carrier out of the enclosure.
2.
Remove the screw from the rear of the carrier (1) and slide the top cover off the carrier (2).
Figure B-1 Removing the Carrier Cover
200 Appendix B Removing and Replacing a Removable 3.5-inch SATA Hard Drive
3.
Remove the adhesive strip that secures the thermal sensor to the top of the hard drive (1) and
move the thermal sensor away from the carrier (2).
Figure B-2 Removing the Thermal Sensor
4.
Remove the four screws from the bottom of the hard drive carrier.
Figure B-3 Removing the Security Screws
201
5.
Slide the hard drive back to disconnect it from the carrier then lift it up and out of the carrier.
Figure B-4 Removing the Hard Drive
6.
Place the new hard drive in the carrier then slide the hard drive back so that it seats in the SATA
connector on the carrier's circuit board. Be sure the connector on the hard drive is pressed all
the way into the connector on the carrier's circuit board.
Figure B-5 Replacing the Hard Drive
202 Appendix B Removing and Replacing a Removable 3.5-inch SATA Hard Drive
7.
Replace the four screws in the bottom of the carrier to hold the drive securely in place.
Figure B-6 Replacing the Security Screws
8.
Place the thermal sensor on top of the hard drive in a position that does not cover the label (1)
and attach the thermal sensor to the top of the hard drive with the adhesive strip (2).
Figure B-7 Replacing the Thermal Sensor
203
9.
Slide the cover on the carrier (1) and replace the screw on the rear of the carrier to secure the
cover in place (2).
Figure B-8 Replacing the Carrier Cover
10. Slide the hard drive carrier into the enclosure on the computer and lock it with the key provided.
NOTE: The carrier must be locked for power to be supplied to the hard drive.
204 Appendix B Removing and Replacing a Removable 3.5-inch SATA Hard Drive
C
Unlocking the Smart Cover Lock
NOTE:
The Smart Cover Lock is an optional feature included on some models only.
The Smart Cover Lock is a software-controllable cover lock, controlled by the setup password. This
lock prevents unauthorized access to the internal components. The computer ships with the
Smart Cover Lock in the unlocked position. For more information about locking the Smart Cover Lock,
refer to the Desktop Management Guide.
Smart Cover FailSafe Key
If you enable the Smart Cover Lock and cannot enter your password to disable the lock, you will need
a Smart Cover FailSafe Key to open the computer cover. You will need the key to access the internal
computer components in any of the following circumstances:
●
Power outage
●
Startup failure
●
PC component (for example, processor or power supply) failure
●
Forgotten password
NOTE: The Smart Cover FailSafe Key is a specialized tool available from HP. Be prepared; order
this key before you need it.
To obtain a FailSafe Key:
●
Contact an authorized HP reseller or service provider. Order PN 166527-001 for the wrenchstyle key or PN 166527-002 for the screwdriver bit key.
●
Refer to the HP Web site (http://www.hp.com) for ordering information.
●
Call the appropriate number listed in the warranty or in the Support Telephone Numbers guide.
Smart Cover FailSafe Key 205
Using the Smart Cover FailSafe Key to Remove the Smart
Cover Lock
To open the access panel with the Smart Cover Lock engaged:
1.
Prepare the computer for disassembly.
2.
Use the Smart Cover FailSafe Key to remove the two tamper-proof screws that secure the Smart
Cover Lock to the chassis.
Figure C-1 Removing the Smart Cover Lock Screws from the Convertible Minitower
Figure C-2 Removing the Smart Cover Lock Screws from the Microtower
206 Appendix C Unlocking the Smart Cover Lock
Figure C-3 Removing the Smart Cover Lock Screws from the Small Form Factor
You can now remove the access panel.
To reattach the Smart Cover Lock, secure the lock in place with the tamper-proof screws.
Using the Smart Cover FailSafe Key to Remove the Smart Cover Lock 207
D
Power Cord Set Requirements
The power supplies on some computers have external power switches. The voltage select switch
feature on the computer permits it to operate from any line voltage between 100-120 or 220-240 volts
AC. Power supplies on those computers that do not have external power switches are equipped with
internal switches that sense the incoming voltage and automatically switch to the proper voltage.
The power cord set received with the computer meets the requirements for use in the country where
you purchased the equipment.
Power cord sets for use in other countries must meet the requirements of the country where you use
the computer.
General Requirements
The requirements listed below are applicable to all countries:
1.
The power cord must be approved by an acceptable accredited agency responsible for
evaluation in the country where the power cord set will be installed.
2.
The power cord set must have a minimum current capacity of 10A (7A Japan only) and a
nominal voltage rating of 125 or 250 volts AC, as required by each country’s power system.
3.
The diameter of the wire must be a minimum of 0.75 mm2 or 18AWG, and the length of the cord
must be between 1.8 m (6 feet) and 3.6 m (12 feet).
The power cord should be routed so that it is not likely to be walked on or pinched by items placed
upon it or against it. Particular attention should be paid to the plug, electrical outlet, and the point
where the cord exits from the product.
WARNING! Do not operate this product with a damaged power cord set. If the power cord set is
damaged in any manner, replace it immediately.
Japanese Power Cord Requirements
For use in Japan, use only the power cord received with this product.
CAUTION: Do not use the power cord received with this product on any other products.
208 Appendix D Power Cord Set Requirements
Country-Specific Requirements
Additional requirements specific to a country are shown in parentheses and explained below.
Country
Accrediting Agency
Country
Accrediting Agency
Australia (1)
EANSW
Italy (1)
IMQ
Austria (1)
OVE
Japan (3)
METI
Belgium (1)
CEBC
Norway (1)
NEMKO
Canada (2)
CSA
Sweden (1)
SEMKO
Denmark (1)
DEMKO
Switzerland (1)
SEV
Finland (1)
SETI
United Kingdom (1)
BSI
France (1)
UTE
United States (2)
UL
Germany (1)
VDE
1.
The flexible cord must be Type HO5VV-F, 3-conductor, 0.75mm2 conductor size. Power cord set fittings (appliance
coupler and wall plug) must bear the certification mark of the agency responsible for evaluation in the country where it
will be used.
2.
The flexible cord must be Type SVT or equivalent, No. 18 AWG, 3-conductor. The wall plug must be a two-pole
grounding type with a NEMA 5-15P (15A, 125V) or NEMA 6-15P (15A, 250V) configuration.
3.
Appliance coupler, flexible cord, and wall plug must bear a “T” mark and registration number in accordance with the
Japanese Dentori Law. Flexible cord must be Type VCT or VCTF, 3-conductor, 0.75 mm2 conductor size. Wall plug
must be a two-pole grounding type with a Japanese Industrial Standard C8303 (7A, 125V) configuration.
Country-Specific Requirements 209
E
Specifications
MT Specifications
Table E-1 Specifications
Chassis
Height
14.9 in
37.7 cm
Width
7.0 in
17.7 cm
Depth
17.0 in
43.1 cm
Approximate Weight
20.5 lb
9.3 kg
Weight Supported (maximum distributed load in desktop
position)
77 lb
35 kg
Operating
50° to 95°F
10° to 35°C
Nonoperating
-22° to 140°F
-30° to 60°C
Temperature Range
NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no
direct sustained sunlight. Maximum rate of change is 10° C/Hr. The upper limit may be limited by the type and
number of options installed.
Relative Humidity (noncondensing)
Operating
10-90%
10-90%
Nonoperating (38.7°C max wet bulb)
5-95%
5-95%
Operating
10,000 ft
3048 m
Nonoperating
30,000 ft
9144 m
Maximum Altitude (unpressurized)
Power Supply
Operating Voltage Range
90-264 VAC
Rated Voltage Range1
100-240 VAC
Rated Line Frequency
50-60 Hz
Operating Line Frequency
47-63 Hz
210 Appendix E Specifications
Table E-1 Specifications (continued)
1
Standard Efficiency
320W
High Efficiency
320W active PFC; 87/90/87% efficient at
20/50/100% load
Rated Input Current
5.5A
This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark
requirements for use in the countries of the European Union. The active power factor corrected power supply also has the
added benefit of not requiring an input voltage range select switch.
MT Specifications 211
SFF Specifications
Table E-2 Specifications
Chassis (in the desktop position)
Height
4.0 in
10.0 cm
Width
13.3 in
33.8 cm
Depth
14.9 in
37.9 cm
Approximate Weight
16.7 lb
7.6 kg
Weight Supported (maximum distributed load in desktop position)
77 lb
35 kg
Operating
50° to 95°F
10° to 35°C
Nonoperating
-22° to 140°F
-30° to 60°C
Temperature Range
NOTE: Operating temperature is derated 1.0° C per 300 m (1000 ft) to 3000 m (10,000 ft) above sea level; no direct
sustained sunlight. Maximum rate of change is 10° C/Hr. The upper limit may be limited by the type and number of options
installed.
Relative Humidity (noncondensing)
Operating
10-90%
10-90%
Nonoperating (38.7°C max wet bulb)
5-95%
5-95%
Operating
10,000 ft
3048 m
Nonoperating
30,000 ft
9144 m
Maximum Altitude (unpressurized)
Power Supply
1
Operating Voltage Range
90-264 VAC
Rated Voltage Range1
100-240 VAC
Rated Line Frequency
50-60 Hz
Operating Line Frequency
47-63 Hz
Standard Efficiency
240W active PFC
High Efficiency
240W active PFC; 87/90/87% efficient at
20/50/100% load
Rated Input Current
4A
This system utilizes an active power factor corrected power supply. This allows the system to pass the CE mark
requirements for use in the countries of the European Union. The active power factor corrected power supply also has the
added benefit of not requiring an input voltage range select switch.
212 Appendix E Specifications
Index
Symbols/Numerics
2.5-in drive adapter, spare part
number 27, 37
A
access panel
locking and unlocking 205
MT removal 52
MT spare part number 52
SFF removal and
replacement 92
SFF spare part number 92
access panel, locked 137
access panel, MT
spare part number 25, 31
access panel, SFF
spare part number 33, 40
adapter, DisplayPort to DVI
spare part number 31, 40
adapter, DisplayPort to DVI (not
illustrated)
spare part number 26, 35
adapter, DisplayPort to HDMI
spare part number 30, 39
adapter, DisplayPort to HDMI (not
illustrated)
spare part number 26, 35
adapter, DisplayPort to VGA
spare part number 30, 39
adapter, DisplayPort to VGA (not
illustrated)
spare part number 26, 35
antenna, spare part number 28,
37
audible codes 184
audio problems 154
B
backing up files 192
Backup and Restore 192, 193
battery
disposal 48
battery replacement 197
beep codes 184
bezel blank
spare part number 56, 96
boot problems 168
booting options
Full Boot 175
Quick Boot 175
C
cable management 49
cable pinouts
SATA data 49
card reader, spare part number
27, 37
cautions
AC power 42
cables 48
cooling fan 47
electrostatic discharge 42
keyboard cleaning 46
keyboard keys 46
CD-ROM or DVD problems 166
chasis types, illustrated 42
chassis fan, MT
spare part number 30
chassis fan, SFF
spare part number 40
chassis stand
spare part number 36
clamp lock, spare part number
28, 29, 37, 39
cleaning
computer 45
mouse 47
safety precautions 45
CMOS
backing up 188
clearing and resetting 190
computer
specifications 212
computer cleaning 45
country power cord set
requirements 209
creating a backup 192
Customer Support 133, 174
D
DIMMs. See memory
disassembly preparation
MT 51
SFF 91
diskette problems 142
DisplayPort cable
spare part number 29, 39
DisplayPort cable (not illustrated)
spare part number 26, 35
DMS-59 to dual VGA cable
spare part number 29, 39
DMS-59 to dual VGA cable (not
illustrated)
spare part number 26, 35
drives
MT cable connections 66
MT installation 66
MT locations 68
SFF cable connections 106
SFF installation 106
SFF locations 106
E
electrostatic discharge (ESD)
preventing damage 43
42
Index 213
error
codes 175, 184
messages 176
eSATA port (expansion), spare
part number 31, 40
eSATA port assembly, spare part
number 28, 37
expansion card
MT installation 60
MT removal 60
SFF installation 100
SFF removal 100
expansion slot cover
MT removal 61
SFF removal 101
external USB webcam, spare part
number 28, 37
F
F11 recovery 195
FailSafe Key 205
fan
MT spare part number 86
fan duct
SFF removal and
replacement 116
SFF spare part number 116
fan duct, SFF
spare part number 36, 40
fan with guard, MT
spare part number 27
fan, MT
spare part number 30
fan, power supply 47
fan, SFF
spare part number 36, 40
fan/baffle assembly
MT removal and replacement
76
FireWire card, spare part
number 30, 40
flash drive problems 169
flashing LEDs 184
front bezel
MT blank removal 56
MT removal 53
MT security 54
MT spare part number 53
removing blanks 96
214 Index
SFF removal and
replacement 93
SFF security 94
SFF spare part number 93
front bezel, MT
spare part number 24, 32
front bezel, SFF
spare part number 33, 41
front fan
SFF removal and
replacement 117
SFF spare part number 117
front fan assembly
MT spare part number 76
front I/O and power switch
assembly
SFF spare part number 120
front I/O assembly
MT spare part number 78
front I/O assembly, MT
spare part number 26, 31
front I/O assembly, SFF
spare part number 35
Front I/O cable and power switch
assembly, SFF
spare part number 40
front I/O, power switch assembly
SFF removal and
replacement 120
front panel components
MT 2
SFF 3
front panel problems 170
front USB panel
MT removal and replacement
78
G
general problems 136
graphics card, spare part
number 29, 38
grommet (hard drive isolation),
spare part number 27, 37
grounding methods 43
guide screws
MT location 67
SFF location 107
H
hard drive
MT installation 72
MT removal 72
proper handling 48
SATA characteristics 49
SFF installation 113
SFF removal 113
spare part numbers 28, 38
hard drive problems 145
hard drive recovery 195
hardware installation problems
160
heat sink
MT removal and replacement
80
MT spare part number 80
SFF removal and
replacement 123
SFF spare part number 123
heat sink, MT
spare part number 27, 30
heat sink, SFF
spare part number 36, 40
helpful hints 134
hood sensor
SFF removal and
replacement 119
SFF spare part number 119
spare part number 27, 30, 36,
40
HP Business Digital Headset,
spare part number 28, 37
I
installing
battery 197
MT drive cables 66
MT expansion card 60
MT hard drive 72
MT media card reader 69
MT memory 57
MT optical drive 69
SFF drive cables 106
SFF expansion card 100
SFF hard drive 113
SFF media card reader 112
SFF memory 97
SFF optical drive 108
Internet access problems 170
K
keyboard
cleaning 46
spare part numbers 28, 29,
30, 37, 39
keyboard problems 158
L
LEDs
blinking power 184
blinking PS/2 keyboard 184
locks
MT front bezel 54
SFF front bezel 94
Smart Cover Lock 205
M
media card reader
MT installation 69
MT removal 68
SFF installation 112
SFF removal 111
Media Card Reader problems
148
memory
MT installation 57
MT socket population 57
MT specifications 57
SFF installation 97
SFF socket population 97
SFF specifications 97
memory module
spare part number 57, 97
memory modules
spare part number 25, 31, 32,
33, 41
memory problems 164
monitor problems 150
mouse
cleaning 47
mouse problems 158
mouse, spare part number 27,
28, 37
MT
access panel, spare part
number 25, 31
disassembly preparation 51
fan with guard, spare part
number 27
fan, spare part number 30
fan/baffle assembly removal
and replacement 76
front bezel, spare part
number 24, 32
front I/O assembly, spare part
number 26, 31
front USB panel removal and
replacement 78
heat sink removal and
replacement 80
heat sink, spare part number
27, 30
power supply removal and
replacement 88
power supply, spare part
number 25, 30
power switch/LED assembly
removal and replacement 79
power switch/LED assembly,
spare part number 26, 31
preparation for disassembly
51
processor removal and
replacement 82
rear chassis fan removal and
replacement 86
SATA hard drive cable, spare
part number 26, 31
SATA optical drive cable, spare
part number 26, 31
speaker removal and
replacement 85
speaker, spare part number
27, 31
system board removal and
replacement 90
system board, spare part
number 25, 31
N
network problems 161
NIC, spare part number 30, 39
numeric error codes 176
O
operating guidelines 45
optical drive
MT installation 69
MT removal 68
SFF installation 108
SFF removal 107
spare part numbers 28, 31,
38, 40
optical drive problems 166
overheating, prevention 45
P
password
clearing 188
power-on 188
setup 188
POST error messages 175
power cord set requirements
country specific 209
power problems 140
power supply
fan 47
MT removal and replacement
88
MT spare part number 88
operating voltage range 210,
212
SFF removal and
replacement 128
power supply, MT
spare part number 25, 30
power supply, SFF
spare part number 33, 39
power switch/LED assembly
MT removal and replacement
79
MT spare part number 79
power switch/LED assembly, MT
spare part number 26, 31
power-on password 188
printer port (expansion), spare part
number 30, 40
printer port, PCI card
spare part number 36
printer port, spare part number
27
printer problems 156
problems
audio 154
CD-ROM or DVD 166
diskette 142
flash drive 169
front panel 170
general 136
hard drive 145
Index 215
hardware installation 160
Internet access 170
keyboard 158
Media Card Reader 148
memory 164
monitor 150
mouse 158
network 161
power 140
printer 156
processor 166
software 173
processor
MT removal and replacement
82
SFF removal and
replacement 125
spare part number 25, 32, 34,
41
processor problems 166
product ID locations 6
R
rear chassis fan
MT removal and replacement
86
MT spare part number 86
rear panel components
MT 4
SFF 5
recovering information 194
recovery partition 195
removal and replacement
MT fan/baffle assembly 76
MT front USB panel 78
MT heat sink 80
MT power supply 88
MT power switch/LED
assembly 79
MT processor 82
MT rear chassis fan 86
MT speaker 85
MT system board 90
SFF fan duct 116
SFF front bezel 92, 93
SFF front fan 117
SFF front I/O, power switch
assembly 120
SFF heat sink 123
SFF hood sensor 119
216 Index
SFF power supply 128
SFF processor 125
SFF speaker 122
SFF system board 130
removing
battery 197
bezel blanks 96
MT bezel blanks 56
MT computer access panel 52
MT expansion card 60
MT expansion slot cover 61
MT front bezel 53
MT hard drive 72
MT media card reader 68
MT optical drive 68
SFF expansion card 100
SFF expansion slot cover 101
SFF hard drive 113
SFF media card reader 111
SFF optical drive 107
Smart Cover Lock 205
resetting
CMOS 188
password jumper 188
restoring the hard drive 195
rubber foot
spare part number 36
S
safety and comfort 133
safety precautions
cleaning 45
SATA
connectors on system board
49
data cable pinouts 49
hard drive characteristics 49
SATA cable, SFF
spare part number 35
SATA drive cable, SFF
spare part number 35
SATA hard drive cable, MT
spare part number 26, 31
SATA optical drive cable, MT
spare part number 26, 31
screws, correct size 47
security
MT front bezel 54
SFF front bezel 94
Smart Cover Lock 205
serial number locations 6
serial port (expansion), spare part
number 30, 40
serial port, spare part number 27,
37
service considerations 47
setup password 188
SFF
access panel, spare part
number 33, 40
chassis fan, spare part
number 40
disassembly preparation 91
fan duct removal and
replacement 116
fan duct, spare part number
36, 40
fan, spare part number 36
front bezel removal and
replacement 92, 93
front bezel, spare part
number 33, 41
front fan removal and
replacement 117
front I/O assembly, spare part
number 35
Front I/O cable and power
switch assembly, spare part
number 40
front I/O, power switch
assembly removal and
replacement 120
heat sink removal and
replacement 123
heat sink, spare part number
36, 40
hood sensor removal and
replacement 119
power supply removal and
replacement 128
power supply, spare part
number 33, 39
preparation for disassembly
91
processor removal and
replacement 125
SATA cable, spare part
number 35
SATA drive cable, spare part
number 35
solenoid lock, spare part
number 36
speaker removal and
replacement 122
speaker, spare part number
36, 40
system board removal and
replacement 130
system board, spare part
number 33, 40
Smart Cover Lock 205
software
problems 173
servicing computer 47
solenoid lock
spare part number 27, 30, 40
solenoid lock, SFF
spare part number 36
solid-state drive, spare part
number 28, 38
spare part number
tamper-resistant wrench 47
Torx T-15 screwdriver 47
speaker
MT removal and replacement
85
MT spare part number 85
SFF removal and
replacement 122
SFF spare part number 122
speaker, MT
spare part number 27, 31
speaker, SFF
spare part number 36, 40
specifications
computer 210, 212
MT memory 57
SFF memory 97
static electricity 42
system board
MT removal and replacement
90
MT spare part number 90
SATA connectors 49
SFF removal and
replacement 130
SFF spare part number 130
system board connections
MT 64
SFF 104
system board, MT
spare part number 25, 31
system board, SFF
spare part number 33, 40
T
tamper-proof screws
tool 47
temperature control 45
tools, servicing 47
Torx T15 screwdriver 47
tower orientation 132
U
unlocking access panel 205
USB powered speakers, spare part
number 27, 30, 37, 40
V
ventilation, proper 45
W
Wake-on-LAN feature 162
Windows 7 operating system
DVD 195
Index 217
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement