Ceiling Mount
PIR Detector
INSTALLATION INSTRUCTIONS
The Bravo 5 is a ceiling mount detector designed to
provide reliable motion detection for residential
and commercial applications. The Bravo 5 uses a
special Fresnel lens made for 360° detection in
conjunction with a quad element PIR sensor
optimized for uniform detection all around its field
of view. Special attention is given to false alarm
immunity against RF, static, electrical transient to
ensure trouble free operation for many years.
Operation
• Maximum detection range (diameter)
Detector placed 8 ft./ 2.4 m from floor: 24 ft./ 7.3 m
Detector placed 10 ft./ 3.0 m from floor: 30 ft./ 9.2 m
Detector placed 12 ft./ 3.6 m from floor: 40 ft./ 12.2 m
• Additional operating modes
LED ON/OFF Jumper J1
Pulse Count (Fast/Slow) Jumper J2
Environmental/Immunity
• RF Immunity: 20V/m ( 100Hz - 1.2GHz)
• Transients @ wiring terminal: 2.4KV @ 1.2joules
• Operating temperature: 32 -122°F / 0 - 50°C
• Humidity 5 - 95% RH non-condensing
Product Information
• BV-500: Form ‘A’ alarm contact
• BV-501: Form ‘A’ alarm contact and tamper switch
• BV-502: Form ‘C’ alarm contact and tamper switch
Features
•
•
•
•
•
•
•
•
•
•
•
Multi-Level Signal Processing *
360° coverage
Quad element PIR sensor
High level static and transient protection
Excellent RF immunity
Temperature compensation
Fast/Slow detection jumper
LED ON/OFF jumper
SMD Construction
Super quiet operation
5 YEAR Warranty
Coverage
Top View (at 8 ft./ 2.4 m height)
The Bravo 5 is designed to be mounted on the ceiling of a
dry indoor location for 360° coverage. Ensure that the
expected path of an intruder is well in the field of view of the
detector. Use the coverage pattern indicated on the
coverage diagram to determine the best sensor location.
Survey the mounting location and the area being protected
for the following potential problems. Avoid following sources
of false alarms:
Reflective Surfaces
Do not aim the detector at reflective surfaces such as
mirrors or windows as this may distort the coverage pattern
or reflect sunlight directly onto the detector.
Air Flow
Avoid locations that are subject to direct high air flow such
as near an air duct outlet.
Moisture
Do not locate the detector near sources of steam or oil.
The Sun
Do not aim the detector such that it will receive direct sunlight.
Obstructions
Do not limit the coverage by placing large objects within the
detection area (such as plants, high shelves, filing cabinets etc.).
Mounting
To open the case, gently twist the top cover counterclockwise and lift it up from the bottom cover. Use a small
screwdriver to remove the appropriate knockouts for wiring.
Mount the bottom cover using the screws supplied.
To close the case, use the locating line on the bottom cover
to align the tab on the top cover. Once the top cover is
engaged, twist the top cover clockwise to lock it in place.
Specifications
Electrical
• Input Voltage: 9 - 14.5 VDC
• Current (nominal): 18 /15 mA (alarm on/off) @12 VDC
Locating the Detector
Side View
NOTE: Since no adjustment is necessary for the circuit
board, it is not recommended that the installer remove the
circuit board from the case.
Contact Rating
• Alarm Relay: 0.1A @24VDC
• Tamper Switch: 0.1A @24VDC
Size (diameter x height)
4.6" x 1.4" / 117 mm x 36 mm
* Patent Pending
WWW.DIYALARMFORUM.COM
Wiring
Testing
Limited Warranty
Refer to the following diagram for wiring instructions:
IMPORTANT NOTE: Upon installation, the unit should be
thoroughly tested to ensure proper working order. The end
user should be instructed on how to perform walk tests, and
should walk test the detector regularly.
Digital Security Controls Ltd. warrants that for a period of five years
from the date of purchase, the product shall be free of defects in
materials and workmanship under normal use and that in fulfilment
of any breach of such warranty, Digital Security Controls Ltd. shall,
at its option, repair or replace the defective equipment upon return
of the equipment to its repair depot. This warranty applies only to
defects in parts and workmanship and not to damage incurred in
shipping or handling, or damage due to causes beyond the control of
Digital Security Controls Ltd. such as lightning, excessive voltage,
mechanical shock, water damage, or damage arising out of abuse,
alteration or improper application of the equipment.
The foregoing warranty shall apply only to the original buyer, and
is and shall be in lieu of any and all other warranties, whether expressed
or implied and of all other obligations or liabilities on the part of
Digital Security Controls Ltd. Digital Security Controls Ltd. neither
assumes, nor authorizes any other person purporting to act on its
behalf to modify or to change this warranty, nor to assume for it any
other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct,
indirect or consequential damages, loss of anticipated profits, loss of
time or any other losses incurred by the buyer in connection with the
purchase, installation or operation or failure of this product.
Motion detectors can only detect motion within the designated areas
as shown in their respective installation instructions. They cannot
discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have multiple beams of detection and motion can only be detected in unobstructed areas covered by these beams. They cannot detect motion
which occurs behind walls, ceilings, floor, closed doors, glass partitions, glass doors or windows. Any type of tampering whether intentional or unintentional such as masking, painting, or spraying of any
material on the lenses, mirrors, windows or any other part of the
detection system will impair its proper operation.
Passive infrared motion detectors operate by sensing changes in temperature. However their effectiveness can be reduced when the ambient temperature rises near or above body temperature or if there are
intentional or unintentional sources of heat in or near the detection
area. Some of these heat sources could be heaters, radiators, stoves,
barbeques, f ireplaces, sunlight, steam vents, lighting and so on.
Warning: Digital Security Controls Ltd. recommends that the entire
system be completely tested on a regular basis. However, despite frequent
testing, and due to, but not limited to, criminal tampering or electrical
disruption, it is possible for this product to fail to perform as expected.
Walk Test
1. Set PIR LED jumper J1 to the ON position.
2. Close the top cover.
3. Create movement in the entire area where coverage is
desired. The LED on the unit will turn on whenever
motion is detected. Should the coverage be incomplete,
relocate the unit. Minor adjustment can be made by
rotating the detector several degrees (use the detection
pattern as a reference) to enhance detection at certain
point in the protected area.
4. If desired, the alarm LED may be disabled by setting
J1 to OFF after the completion of the walk test.
Power Up
Upon application of power, the LED will be on for
approximately 90 seconds to indicate that the unit is warming
up. During this period, the relay is held in its alarm state. After
the 90 second warm-up period, the LED will turn off and the
unit will respond to motion in the protected area.
Important Information: Changes or modifications not expressly approved
by Digital Security Controls Ltd. could void the user’s authority to operate
this equipment.
WWW.DIYALARMFORUM.COM
© 1997 Digital Security Controls Ltd., Toronto, Canada
1645 Flint Road, Downsview, Ontario Canada M3J 2J6
(416) 665-8460 Fax: (416) 665-7498
29002462 R1
">
