HP | HSR6600 | Command Reference Guide | HP HSR6600 Command Reference Guide

About the HP 6600/HSR6600 Command
References
The HP 6600/HSR6600 command references are part of the HP 6600/HSR6600 Routers
documentation set. They describe the commands and command syntax options available for the HP
6600/HSR6600 Routers. The HP 6600/HSR6600 documentation set includes 13 command references:
Command reference
Content
Fundamentals Command
Reference
Covers the commands for logging in to and setting up an 6600/HSR6600
Router. This command reference includes:
• CLI
• Logging In to the Router
• FTP and TFTP
• File Management
• Configuration File Management
• Software Upgrade
• Device Management
Interface Command Reference
Covers the interface configuration commands. This command reference
includes:
• Ethernet Interface
• ATM Interface
• WAN Interface
• POS Interface
• CPOS Interface
• E-CPOS Interface
• Loopback and Null Interface
Layer 2 – LAN Switching
Command Reference
Covers the commands for configuring Layer 2 technologies and features in
a LAN switched network. This command reference includes:
• MAC Address Table
• Ethernet Link Aggregation
• Port Isolation
• MSTP
• BPDU Tunneling
• VLAN
• GVRP
• QinQ
• VLAN Termination
• VLAN Mapping
• LLDP
Layer 2 – WAN Access
Command Reference
Covers WAN access technologies. This command reference includes:
• ATM
• PPP
• L2TP
• HDLC
• Frame Relay
• Modem Management
Layer 3 – IP Services Command
Reference
Covers the commands for configuring and managing IP addressing
(including static and dynamic IPv4 and IPv6 address assignment), network
performance optimization, ARP, and interoperation between IPv4 and IPv6.
This command reference includes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Layer 3 – IP Routing Command
Reference
ARP
IP Addressing
DHCP
DNS
NAT
IP Forwarding Basics
Flow Classification
Adjacency Table
IP Performance Optimization
UDP Helper
IPv6 Basics
DHCPv6
IPv6 DNS
NPT
AFT
Tunneling
GRE
DVPN
Covers the commands for configuring routes for IPv4 and IPv6 networks of
different sizes, route filtering, route control, and policy based routing. This
command reference includes:
• IP Routing Basics
• Static Routing
• RIP
• OSPF
• IS-IS
• BGP
• PoliBased Routing
• IPv6 Static Routing
• RIPng
• OSPFv3
• IPv6 IS-IS
• IPv6 BGP
• IPv6 PoliBased Routing
• Routing Policy
• MTR
IP Multicast Command
Reference
Covers the commands for Layer 3 IPv4 multicast protocols IGMP, PIM,
MBGP, and Layer 3 IPv6 multicast protocols MLD, IPv6 PIM, MSDP, and
IPv6 MBGP), Layer 2 IPv4 multicast protocols (IGMP snooping). This
command reference includes:
• IGMP Snooping
• Multicast Routing and Forwarding
• IGMP
• PIM
• MSDP
• MBGP
• Multicast VPN
• IPv6 Multicast Routing and Forwarding
• MLD
• IPv6 PIM
• IPv6 MBGP
• PIM Snooping
• Multicast VLAN
MPLS Command Reference
Describes the commands to configure MPLS and MPLS VPN, This command
reference includes:
• MPLS Basics
• MPLS TE
• MPLS L2VPN
• VPLS
• MPLS L3VPN
ACL and QoS Command
Reference
Covers the commands for classifying traffic with ACLs, and allocating
network resources and managing congestions with QoS technologies to
improve network performance and network use efficiency. This command
reference includes:
• ACL
• QoS
• MPLS QoS
• FR QoS
Security Command Reference
Covers security feature commands. Available security features include
identity authentication (AAA), access security (802.1X, MAC
authentication, and portal), secure management (SSH), and attack
protection (Firewall, TCP and ICMP Attack Protection, ARP attack
protection, ARP Attack Protection, ND Attack Defense and URPF). This
command reference includes:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AAA
802.1X
MAC Authentication
Portal
Port Security
User Profile
Password Control
RSH
Public Key
PKI
IPsec
SSH2.0
SSL
SSL VPN
Firewall
ALG
Session Management
Connection Limit
Web Filtering
Attack Detection and Protection
• TCP and ICMP Attack Protection
• IP Source Guard
• ARP Attack Protection
• ND Attack Defense
• URPF
• FIPS
High Availability Command
Reference
Covers high availability commands for managing failure detection and
failover. Failure detection technologies focus on fault detection and
isolation. Failover technologies focus on network recovery. This command
reference includes:
• Active and Standby Switchover
• Ethernet OAM
• CFD
• DLDP
• RPR
• RRPP
• Smart Link
• VRRP
• Stateful Failover
• BFD
• Track
Network Management and
Monitoring Command
Reference
Covers the commands that help you manage and monitor your network, for
example, manage system events, collect traffic statistics, sample packets,
assess network performance, and test network connectivity. This command
reference includes:
• System Maintenance and Debugging
• NQA
• NTP
• IPC
• SNMP
• RMON
• Sampler
• Mirroring
• NetStream
• IPv6 NetStream
• Information Center
• Flow Logging
• sFlow
• Gateway Mode
OAA Command Reference
Describes the commands of OAA-based protocols ACFP and ACSEI . This
guide includes:
• OAP Module
• ACFP
• ACSEI
Download PDF

advertising