owner`s manual - Trail Appliances
ENGLISH
FRANÇAIS
OWNER’S MANUAL
DRYER
Please read this owner’s manual thoroughly before operating and keep it
handy for reference at all times.
DLEY1701*E
DLGY1702*E
MFL67731050
MFL67731050_en_141213.indd 1
www.lg.com
2014.12.13 5:20:59 PM
2
TABLE OF CONTENTS
TABLE OF CONTENTS
3
IMPORTANT SAFETY INSTRUCTIONS
31
HOW TO USE
3
4
5
5
WHAT TO DO IF YOU SMELL GAS
BASIC SAFETY PRECAUTIONS
GROUNDING INSTRUCTIONS
SAFETY INSTRUCTIONS FOR
INSTALLATION
SAFETY INSTRUCTIONS FOR CONNECTING
ELECTRICITY
31
32
32
32
33
34
35
35
36
36
37
38
Operating the Dryer
Sorting Loads
Loading the Dryer
Check the Lint Filter Before Every Load
Using the LG EasyLoad™
Cycle Guide
Cycle Settings and Options
Special Functions
Custom Program
Steam Functions
Tag On
Using Tag On with Applications
7
8
PRODUCT FEATURES
9
INTRODUCING YOUR DRYER
9
9
9
10
11
Parts
Accessories
2-Way Reversible Door
Control Panel Features
Display
44
MAINTENANCE
44
Regular Cleaning
45
TROUBLESHOOTING
12
INSTALLATION INSTRUCTIONS
45
Before Calling for Service
12
13
13
14
15
21
22
24
25
27
28
Preview Installation Order
Installation Location Requirements
Clearances
Leveling the Dryer
Reversing the Door
Installing the Side Vent Kit
Venting the Dryer
Connecting Inlet Hose
Connecting Gas Dryers
Connecting Electric Dryers
Special Requirements for Manufactured or
Mobile Homes
Final Installation Check
Installation Test (Duct Check)
47
SPECIFICATIONS
48
USING SMART DIAGNOSISTM
49
WARRANTY
28
29
MFL67731050_en_141213.indd 2
2014.12.13 5:20:59 PM
IMPORTANT SAFETY INSTRUCTIONS
3
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
Your safety and the safety of others is very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all
safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER, WARNING, or CAUTION.
w
These words mean:
wDANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
wWARNING
You can be killed or seriously injured if you don’t follow instructions.
wCAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell
you what can happen if the instructions are not followed.
• Do not install a clothes dryer ith flexible plastic venting materials. If flexible metal (foil type) duct is
installed, it must be of a specific type identified by the appliance manufacturer as suitable for use ith
clothes dryers. Flexible venting materials are no n to collapse, be easily crushed, and trap lint. These
conditions ill obstruct clothes dryer airflo and increase the ris of fire.
• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this appliance or any
other appliances.
• Installation and service must be performed by a qualified installer, service agency, or the gas supplier.
• Install the clothes dryer according to the manufacturer’s instructions and local codes.
• Save these instructions.
WHAT TO DO IF YOU SMELL GAS:
1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.
2. Do not touch any electrical s itches. Do not use any phone in your building.
3. Clear the room, building, or area of all occupants.
4. Immediately call your gas supplier from a neighbor’s phone. Follo the gas supplier’s instructions
carefully.
5. If you cannot reach your gas supplier, call the fire department.
wWARNING:This product contains chemicals known to the State of California to cause cancer and birth defects or
other reproductive harm. Wash hands after handling.
MFL67731050_en_141213.indd 3
2014.12.13 5:20:59 PM
4
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
bASIC SAFETY pRECAUTIONS
wWARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Read all instructions before using the dryer.
• Before use, the dryer must be properly installed as
described in this manual.
• Do not place items exposed to cooking oils in your
dryer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
• Do not dry articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline, drycleaning solvents, or other flammable or explosive
substances as they give off vapors that could ignite or
explode.
• Do not reach into the dryer if the drum or any other
part is moving.
• Do not repair or replace any part of the dryer
or attempt any servicing unless specifically
recommended in this owner’s manual or in published
user-repair instructions that you understand and have
the skills to carry out.
• Do not tamper ith controls.
• Before the dryer is removed from service or discarded,
remove the door to the drying compartment.
• Do not allo children to play on or in the dryer. Close
supervision of children is necessary when the dryer is
used near children.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of
the fabric softener or product.
• Do not use heat to dry articles containing foam rubber
or similarly textured rubber-like materials.
• Keep area around the exhaust opening and adjacent
surrounding areas free from the accumulation of lint,
dust, and dirt.
• The interior of the dryer and exhaust vent should be
cleaned periodically by qualified service personnel.
• Do not install or store the dryer here it ill be
exposed to the weather.
• Al ays check the inside of the dryer for foreign
objects.
• Clean lint screen before or after each load.
• Do not store plastic, paper, or clothing that may
burn or melt on top of the dryer during operation.
• Be careful hen opening and closing the door.Fingers
and hands can get caught in the door and cause injury
if the door drops forward unexpectedly.
• Do not place heavy items on or lean against the top
of the door hen it is open.
• Do not attempt to pull the hamper door open more
than 40 degrees.
• The dryer could tip for ard, causing injury or damage.
• Do not place items on the top of the dryer.
MFL67731050_en_141213.indd 4
2014.12.13 5:20:59 PM
IMPORTANT SAFETY INSTRUCTIONS
5
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of
malfunction or breakdown, grounding will reduce
the risk of electric shock by providing a path of least
resistance for electric current. This appliance must be
equipped with a cord having an equipment-grounding
conductor and a grounding plug. The plug must be
plugged into an appropriate outlet that is properly
installed and grounded in accordance with all local
codes and ordinances.
Do not modify the plug provided with the appliance. If
it will not fit the outlet, have a proper outlet installed by
a qualified electrician.
This appliance must be connected to a grounded metal,
permanent wiring system or an equipment-grounding
conductor must be run with the circuit conductors and
connected to the equipment-grounding terminal or
lead on the appliance.
Electric shock can result if the dryer is not properly
grounded.
wWARNING
Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or service person if you are in doubt that the appliance is properly grounded.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• properly ground dryer to conform ith all
governing codes and ordinances. Follow details in
the installation instructions. Electric shock can result if
the dryer is not properly grounded.
• before use, the dryer must be properly installed as
described in this manual. Electric shock can result if
the dryer is not properly grounded.
• Install and store the dryer here it ill not be
exposed to temperatures belo freezing or
exposed to the eather.
• All repairs and servicing must be performed
by an authorized servicer unless specifically
recommended in this o ner’s manual. Use only
authorized factory parts. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
• To reduce the ris of electric shoc , do not install
the dryer in humid spaces. Failure to follow this
warning can cause serious injury, fire, electric shock, or
death.
• Remove all pac ing items and dispose of all
shipping materials properly. Failure to do so can
result in death, explosion, fire, or burns.
• place dryer at least 18 inches above the floor for
a garage installation. Failure to do so can result in
death, explosion, fire, or burns.
• Keep all pac aging from children. Packaging
material can be dangerous for children. There is a risk
of suffocation.
• Do not install near another source of heat such as
a stove, coo ing oven. Failure to do so can cause
deform, smoke and fire.
• Do not place candles, smo ing materials, or other
flammables on top of the product. Dripping wax,
smoke, or fire can result.
• Remove all protective vinyl film from the product.
Failure to do so can cause product damage, smoke or
fire.
• Connect to a properly rated, protected, and sized
po er circuit to avoid electrical overload. Improper
power circuit can melt, creating electric shock and/or
fire hazard.
MFL67731050_en_141213.indd 5
2014.12.13 5:21:0 PM
6
IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
wWARNING
To reduce the risk of injury to persons, follow all industry recommended safety procedures including the use of long
sleeved gloves and safety glasses. Failure to follow all of the safety warnings in this manual could result in property
damage, injury to persons, or death.
Exhaust/Ducting:
• Gas dryers MUST be exhausted to the outside.
Failure to follow these instructions can result in fire or
death.
• The dryer exhaust system must be exhausted
to the outside of the d elling. If the dryer is not
exhausted outdoors, some fine lint and large
amounts of moisture ill be expelled into the
laundry area. An accumulation of lint in any area of
the home can create a health and fire hazard.
• Use only rigid metal or flexible metal 4-inch
diameter duct or inside the dryer cabinet or for
exhausting to the outside. Use of plastic or other
combustible duct or can cause a fire. Punctured
ductwork can cause a fire if it collapses or becomes
otherwise restricted in use or during installation.
• Duct or is not provided ith the dryer, and you
should obtain the necessary duct or locally. The
end cap should have hinged dampers to prevent
bac draft hen the dryer is not in use. Failure to
follow these instructions can result in fire or death.
MFL67731050_en_141213.indd 6
• The exhaust duct must be 4 inches (10.2 cm) in
diameter ith no obstructions. The exhaust duct
should be ept as short as possible. Ma e sure
to clean any old ducts before installing your ne
dryer. Failure to follow these instructions can result in
fire or death.
• Rigid or semi-rigid metal ducting is recommended
for use bet een the dryer and the all. In special
installations hen it is impossible to ma e a
connection ith the above recommendations, a ULlisted flexible metal transition duct may be used
bet een the dryer and all connection only. The
use of this ducting ill affect drying time. Failure to
follow these instructions can result in fire or death.
• DO NOT use sheet metal scre s or other fasteners
hich extend into the duct that could catch lint and
reduce the efficiency of the exhaust system. Secure
all joints with duct tape. For complete details, follow
the Installation Instructions. Failure to follow these
instructions can result in fire or death.
2014.12.13 5:21:0 PM
IMPORTANT SAFETY INSTRUCTIONS
7
IMPORTANT SAFETY INSTRUCTIONS
ENGLISH
READ ALL INSTRUCTIONS BEFORE USE
wWARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric
shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY
wWARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Do not, under any circumstances, cut or remove
the ground prong from the po er cord. To prevent
injury to persons or damage to the dryer, the electrical
power cord must be plugged into a properly grounded
outlet.
• For personal safety, this dryer must be properly
grounded. Failure to do so can result in electric shock
or injury.
• Refer to the installation instructions in this manual
for specific electrical requirements for your model.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
• This dryer must be plugged into a properly
grounded outlet. Electric shoc can result if the
dryer is not properly grounded. Have the all
outlet and circuit chec ed by a qualified electrician
to ma e sure the outlet is properly grounded.
Failure to follow these instructions can create an
electric shock hazard and/or a fire hazard.
• The dryer should al ays be plugged into its o n
individual electrical outlet hich has a voltage
rating that matches the rating plate. This provides
sparkling performance and also prevents overloading
house wiring circuits which could cause a fire hazard
from overheated wires.
• Never unplug your dryer by pulling on the po er
cord. Al ays grip plug firmly and pull straight out
from the outlet. The power cord can be damaged,
resulting in a risk of fire and electric shock.
• Repair or replace immediately all po er cords that
have become frayed or other ise damaged. Do not
use a cord that sho s crac s or abrasion damage
along its length or at either end. The power cord can
melt, creating an electric shock and/or fire hazard.
• When installing or moving the dryer, be careful not
to pinch, crush, or damage the po er cord. This will
prevent injury and prevent damage to the dryer from
fire and electric shock.
SAVE THESE INSTRUCTIONS
MFL67731050_en_141213.indd 7
2014.12.13 5:21:0 PM
8
PRODUCT FEATURES
PRODUCT FEATURES
EASY-TO-USE CONTROL PANEL
An entire selection of user-friendly functions make operating the dryer easy.
2-WAY EASY-ACCESS REVERSIBLE DOOR
The LG EasyLoad™ can be tilted open from the top, hamper-style, allowing you to easily load the dryer without
items falling on the floor. The door still swings open to provide easy access for unloading or loading of bulkier
items. The door hinge can be reversed to adjust for installation location.
STEAM FUNCTIONS
LG’s steam technology allows you to inject fabrics with a swirling jet of steam to refresh clothes, reduce static, and
make ironing easier. Simply select the Steam Fresh™ cycle or Wrinkle Care cycle.
Flow Sense™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR
The Flow Sense™ duct blockage sensing system detects and alerts you to restrictions in the installed household
ductwork that reduce exhaust airflow through the dryer. If you see the alert: Clean or repair the ducts to remove
the restrictions. Keep your ducts clean to help increase efficiency and reduce long drying times caused by blocked
ducts.
Smart Diagnosis™
Should you experience any technical difficulty with your dryer, it has the capability of transmitting data via your
telephone to the Customer Information Center. The call center agent records the data transmitted from your
machine and uses it to analyze the issue, providing a fast and effective diagnosis.
Tag On
D
The Tag On feature works on most smart phones equipped with the NFC function and based on the Android
operating system (OS).
Using the “LG Smart Laundry” application, the Tag On feature will allow you to diagnose your appliance, download
new cycles, and see the status of your appliance by simply touching the smartphone to the Tag On logo of the
appliance.
ES
C
ER
IGN
TIFIE
D
protocol p154
Sanitization performance of
Residential Clothes dryer
MFL67731050_en_141213.indd 8
2014.12.13 5:21:1 PM
INTRODUCING YOUR DRYER
9
INTRODUCING YOUR DRYER
ENGLISH
Parts
Control
panel
Reversible
door
Lint filter
Leveling
feet
Accessories
Power cord
location
(Gas
models)
Power Cord
Location
(Electric
Models)
Gas
connection
location
(Gas models)
Water inlet
valve
Exhaust
duct
outlet
2-Way Reversible Door
Included accessories
Release
Y connector
Hose
Optional accessories
Hamper door
Swing door
Drying rack
Side vent kit
(sold separately)
Kit No. 383EEL9001B
The LG EasyLoad™ feature allows you to open the dryer
door from the top, hamper-style, when loading the
dryer to help guide clothes into the drum and prevent
them from falling onto the floor. When unloading the
dryer or loading bulkier items, use the swing door for
easy access to the drum. For more details on using the
door, see page 33. For information on reversing the
door s ing, see page 15.
NOTE
• Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are missing.
• For your safety and for extended product life, use only authorized components. The manufacturer is not
responsible for product malfunction or accidents caused by the use of separately purchased unauthorized
components or parts.
• The images in this o ner’s manual may be different from the actual components and accessories, and are
subject to change by the manufacturer without prior notice for product improvement purposes.
MFL67731050_en_141213.indd 9
2014.12.13 5:21:10 PM
10
INTRODUCING YOUR DRYER
Control Panel Features
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
wWARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
G
F
D
E
A pOWER ON/OFF bUTTON
Press to turn the dryer ON. Press again to turn
the dryer OFF.
NOTE
Pressing the ON/OFF button during a cycle will
cancel that cycle and any load settings will be lost.
B CYCLE bUTTONS
Press the Cycle button repeatedly to scroll
through the cycle selections until the desired
cycle is selected. The standard presets for the
selected cycle will be shown in the display.
On MANUAL DRY cycles, these settings can be
adjusted using the cycle setting buttons anytime
before starting the cycle.
C START/pAUSE bUTTON
Press this button to start the selected cycle. If
the dryer is running, use this button to pause
the cycle without losing the current settings.
NOTE
If you do not press the START/PAUSE button to
resume a cycle ithin 4 minutes, the dryer turns
off automatically.
A
H
B
C
D MORE TIME/LESS TIME bUTTONS
Use these buttons with the Time Dry and other
MANUAL DRY cycles to adjust the drying time.
Press the More Time button to increase the
selected manual cycle time by one minute;
press Less Time to decrease the cycle time by
one minute.
E CYCLE SETTING bUTTONS
Use these buttons to select the desired cycle
settings for the selected cycle. The current
settings are shown in the display. Press the
button for that option to select other settings.
F TIME AND STATUS DISpLAY
The display shows the settings, estimated time
remaining, options, and status messages for
your dryer.
G OpTION bUTTONS
The option buttons allow you to select
additional cycle options. Certain buttons also
allow you to activate special functions by
pressing and holding the button for 3 seconds.
H STEAM FUNCTIONS
LG’s steam technology allows you to inject
fabrics with a swirling jet of steam to refresh
clothes, reduce static, and make ironing
easier. Simply select the Steam Fresh™ cycle or
Wrinkle Free cycle.
MFL67731050_en_141213.indd 10
2014.12.13 5:21:12 PM
E
H
B
C
INTRODUCING YOUR DRYER
11
Display
wWARNING
To reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety
Instructions, before operating this dryer.
F
D
B
C
E
A ESTIMATED TIME REMAINING
This display shows the estimated time remaining
for SENSOR DRY cycles or the actual time
remaining for Time Dry or MANUAL DRY cycles.
NOTE
ENGLISH
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
A
D CLEAN FILTER REMINDER
The display will show Clean Filter when the
dryer is turned on as a reminder to check the
filter. It turns off when the START/PAUSE button
is pressed.
The cycle time on SENSOR DRY cycles may
fluctuate as the dryer recalculates drying time for
optimal results.
B CYCLE COMpLETION INDICATOR
WITH CHECK FILTER REMINDER
This portion of the display shows which stage
of the drying cycle is currently underway (Clean
Filter, Drying, Cooling).
C CHILD LOCK INDICATOR
When Child Lock is set, the Child Lock indicator
will appear and all buttons are disabled except
the POWER button. This prevents children from
changing settings while the dryer is operating.
MFL67731050_en_141213.indd 11
E CUSTOM pROGRAM
If you have a special combination of settings
that you use frequently, you can save these
settings as a Custom Program.
F Flo Sense DUCT bLOCKAGE
SENSING SYSTEM INDICATOR
The Flow Sense™ duct blockage sensing
system detects and alerts you to blockages in
the ductwork that reduce exhaust flow from
the dryer. Maintaining a clean exhaust system
improves operating efficiency and helps
minimize service calls, saving your money.
2014.12.13 5:21:13 PM
12
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
Preview Installation Order
Checking and
choosing the proper
location
Leveling the dryer
Connecting the inlet hose
120V
Venting the dryer
Connecting gas
dryers
240V(USA)
230V(CANADA)
Press and hold
Plugging in the
power cord and
grounding
MFL67731050_en_141213.indd 12
Installation test
Test run
(Refer to page 29.)
2014.12.13 5:21:14 PM
INSTALLATION INSTRUCTIONS
13
Installation Location Requirements
Read all installation instructions completely before installing and operating your dryer It is important that
you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical
connections, gas connections, and exhaust requirements are provided on the following pages.
• A location that allo s for proper exhaust installation. A
gas dryer must be exhausted to the outdoors.
See Venting the dryer.
• A sturdy floor to support the total dryer eight of 200
lbs (90.7 kg). The combined eight of a companion
appliance should also be considered.
• A grounded electrical outlet located ithin 2 ft.
(61 cm) of either side of the dryer. See Connecting
electric dryers.
• No other fuel-burning appliance can be installed in the
same closet as a dryer.
ENGLISH
wWARNING
Do not operate your dryer at temperatures belo 45°F (7°C). At lo er temperatures, the dryer might not shut off
at the end of an automatic cycle. This can result in longer drying times. The dryer must not be installed or stored in
an area where it will be exposed to water and/or weather. Check code requirements. Some codes limit, or do not
permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building
inspector.
NOTE
• A level floor ith a maximum slope of 1 inch (2.5 cm) under entire dryer. If slope is greater than 1 inch (2.5 cm),
install the Extended Dryer Feet Kit. Clothes may not tumble properly, and automatic sensor cycles may not
operate correctly if dryer is not level.
• For a garage installation, you ill need to place the dryer at least 18 inches (46 cm) above the floor. If using a
pedestal, you ill need 18 inches (46 cm) to the bottom of the dryer.
Clearances
(7.6 cm)
14" max.*
(35.6 cm)
21 1/4"
(54 cm)
40 3/16"
(102 cm)
28 15/16"
(73.4 cm)
5"**
(12.7 cm)
(2.54 cm)
(68.6 cm)
(2.54 cm)
50 1/4"
(127.5 cm)
Closet Door Vent
(7.6 cm) Requirements
INSTALLATION SPACING FOR RECESSED AREA OR CLOSET INSTALLATION
(7,6 cm)
The following spacing dimensions
are recommended for this dryer. This dryer has been
tested for spacing of
14" max.*
cm)
1 inch clearance on the
and(35,6rear.
Recommended spacing should be considered for the follo ing reasons:
21 /sides
"
1 4
(54 cm)
40 3/16"
(102 cm)
• Additional spacing should be considered
for ease of
installation and servicing.
• Additional spacing should be considered on all sides
of the dryer to reduce noise transfer.
• Additional clearances might be required for all, door
28 / "
5"**
and floor moldings.
(73,4 cm)
(2,54 cm)
(12,7 cm)
(68,6 cm)
15 16
50 1/4"
(127,5 cm)
NOTE
For closet installation, with a door, minimum
ventilation
openings in the top and bottom of the
(2,54 cm)
Requisitos de ventilación
(7,6 cm) doors
de la puertawith
del armario
door are required. Louvered
equivalent
ventilation openings are acceptable.
• Companion appliance spacing should also be
(7,6 cm)
considered.
14" max.*
(35,6 cm)
21 1/4"
(54 cm)
There should be at least a little space around the dryer (or any other appliance) to eliminate the transfer of
40 / "
vibration from one to the other. Too much
vibration, it could cause them to make noise or touch each other
(102 cm)
causing paint damage and making even more noise.
3 16
28 15/16"
(73,4 cm)
50 1/4"
(127,5 cm)
MFL67731050_en_141213.indd 13
5"**
(12,7 cm)
(2,54 cm)
(68,6 cm)
(2,54 cm)
(7,6 cm)
2014.12.13 5:21:16 PM
14
INSTALLATION INSTRUCTIONS
50 1/4"
(127,5 c
Clearances (cont.)
RECOMMENDED INSTALLATION SPACING FOR CABINET INSTALLATION
• For cabinet installation with a door, minimum ventilation openings in the top of the cabinet are required.
7"* (17.8 cm)
*Required spacing
7"* (17.8 cm)
**For side or bottom venting,
2 inches (5.1 cm) spacing is allo ed.
5"* 28
1"*
(12.7 cm) (73.4 cm) (2.5 cm)
1"
27 "
(2.54 cm) (68.6 cm)
1"
(2.54 cm)
Leveling the Dryer
wWARNING
• To reduce the ris of injury to persons, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
Failure to follow this warning can cause serious injury
or death.
• The appliances are heavy. T o or more people are
required hen installing the dryer. Failure to follow
this warning can cause serious injury or death.
To ensure that the dryer provides optimal drying
performance, it must be level. To minimize vibration,
noise, and unwanted movement, the floor must be a
perfectly level, solid surface.
• All four leveling feet must rest solidly on the floor.
Gently push on the top corners of the dryer to make
sure that the dryer does not rock from corner to corner.
If you are installing the dryer on the optional pedestal,
you must use the leveling feet on the pedestal to
level the dryer. The dryer leveling feet should be fully
retracted.
2. Use an adjustable rench to turn the leveling feet.
Turn clockwise to raise the dryer or counterclockwise
to lower it. Raise or lower the leveling feet until dryer
is level from side to side and front to back.
Make sure that all 4 leveling feet are in firm contact ith
the floor.
NOTE
Adjust the leveling feet only as far as necessary to
level the dryer. Extending the leveling feet more than
necessary can cause the dryer to vibrate.
1. Position the dryer in the final location. Place a level
across the top of the dryer.
Level
Leveling Feet
MFL67731050_en_141213.indd 14
2014.12.13 5:21:18 PM
INSTALLATION INSTRUCTIONS
15
Reversing the Door
NOTE
The door reversal procedure for the two-way door
is far more complex than for a conventional dryer
door. It is recommended that you read through these
instructions in their entirety before beginning the
process, in order to gauge whether you prefer to have
the procedure done by a professional installer or
service person.
The door reversal procedure consists of four main parts:
• Removing and reinstalling the door and hinges (steps
1, 2 and 20)
• Removing and reversing components on the dryer
cabinet (step 3)
• Removing and reversing components on the door
cover (steps 4 and 5)
• Removing and reversing components inside the door
(steps 6 through 19).
Tools Required
• phillips scre driver
• Large flat blade scre driver (recommended for hinge
screws if they are tight or your Phillips screwdriver is
worn)
• Small flat blade scre driver (for lifting out parts)
wWARNING
• To avoid damage to the dryer or the door, support
the door ith a stool or box that fits under the door,
or have an assistant support the eight of the door.
• Avoid dropping the door to avoid damage to the
door or the floor.
• Unplug the dryer or turn off po er at the main
circuit brea er before beginning door reversal.
• THE DRYER DOOR IS VERY LARGE AND HEAVY.
Failure to follo the instructions belo can result in
damage to the dryer, property damage or personal
injury.
Instructions
NOTE
The instructions here are for changing the door swing
from a right to a left side hinge. If the door has been
reversed, and it is necessary to change it back, use
care when following these instructions. Some of
the illustrations and the left/right references will be
reversed, and you will need to read the instructions
carefully.
MFL67731050_en_141213.indd 15
wWARNING
Be sure to support the eight of the door before
removing the hinge screws.
ENGLISH
before you begin
1. Open the door from the side so that the hinge
scre s are accessible.
Two large
screws
Two small
screws
2. Remove the four hinge scre s.
While supporting the door, remove the four hinge
screws, two from each hinge. Set the door aside face
down on a protected surface to prevent damage to
the door or the work surface.
3. Reverse the components on the cabinet.
a. Use a Phillips screwdriver to remove the two screws
and the latch mechanism on the front panel of the
cabinet.
hinge
cover
latch
mechanism
hinge
upper
hinge
latch hole
cover
hinge
bracket
b. Remove the latch hole cover by gently prying it
up with a flat blade screwdriver, being careful not
to scratch the paint. Install the latch hole cover on
the opposite side, where the latch mechanism was
removed. Install the latch mechanism in the position
from which you removed the latch hole cover, using
the two screws removed in step a.
c. Remove the hinge cover by gently prying it up with
a flat blade screwdriver, being careful not to scratch
the paint. Rotate the hinge cover 180 degrees and
install it on the opposite side, where the upper hinge
was attached.
2014.12.13 5:21:19 PM
16
INSTALLATION INSTRUCTIONS
Reversing the Door (cont.)
hinge
cover
latch
mechanism
hinge
upper
hinge
latch hole
cover
hinge
bracket
ON THE DOOR:
4. Lift off the door cover.
With the door laid inside facing up on a protected
surface, remove the 12 scre s on the inside of the
door. Carefully lift off the door cover with the help of
a small flat blade screwdriver inserted in the upper
corner (circled below).
wWARNING
The edges of the door cover may be sharp. Take care
when handling, or wear gloves to avoid injury.
twelve screws
d. Reverse the hinge and the hinge bracket at the
bottom of the cabinet. Remove the two screws from
the hinge bracket at bottom right and remove the
hinge bracket.
Remove the lower of the two
screws behind the hinge
bracket. Do NOT remove the
upper screw behind the hinge
bracket. Set the parts aside.
Hole
plug
interlock
button
NOTE
Do NOT remove any of the eight screws on the face of
below). Doing so could
the cabinet (marked with
result in damage to the dryer and the need for a
service call to repair the dryer.
5. S itch the door stri e and the blan cover.
Remove the four screws on the door cover that secure
the door strike and the blank cover.
Switch the door strike and the blank cover, installing
them on the opposite sides from which they were
removed.
short
screws
long screw
blank cover
door strike
Gently pry out the hole plug on the side of the door
cover and install it in the hole on the opposite side.
e. Remove the three screws on the
hinge at bottom left. Remove the
hinge and reinstall it on the right
side. The top screw occupies the
hole where you removed the screw
behind the hinge bracket in step d.
f. Install the hinge bracket removed in step d on the
bottom left side, first installing one screw behind the
hinge bracket.
MFL67731050_en_141213.indd 16
hole plug
Set the door cover aside.
2014.12.13 5:21:22 PM
INSTALLATION INSTRUCTIONS
17
Reversing the Door (cont.)
ENGLISH
6. Reverse the components inside the door.
You will now be removing and reversing various components inside the door. See below for a detailed diagram
and identification of the inner structure and parts of the door. (The diagram shows the “before view” of the door,
with the default set-up for a right side hinge swing. After following these instructions, your door should be a
mirror image of the illustration.)
Inner Structure of Door
(before reversing - right hinge swing)
Top interlock buttons
inner lock rods
upper hinge
assembly
upper hinge
filler
upper hinge
pivot
top lock rod
side lock rod
glass
Side Interlock button
lower hinge
filler
lower
hinge
assembly
lower
hinge
bracket
bumpers
interlock buttons
lower hinge filler
side lock rod
top lock rod
inner lock rods
lower hinge bracket
Hole plug
lower hinge assembly
MFL67731050_en_141213.indd 17
2014.12.13 5:21:27 PM
18
INSTALLATION INSTRUCTIONS
Reversing the Door (cont.)
7. Lift out the t o top interloc buttons.
Lift out the two grey interlock buttons from the top of
the outer door and set them aside for later use.
interlock buttons
side lock rod
8. Lift out the grey interloc button in the side of the
door.
Make sure to remove the spring with the interlock
button and to keep the two together. Set the interlock
button aside. Do not confuse with interlock buttons
from the top of the outer door.
b. While sliding the lock rod right, lift the right end up
and out of the guides.
NOTE
Do not remove the t o inner lock rods (see page 17)
located underneath the top lock rod. They do NOT
need to be reversed
11. Remove the upper hinge pivot.
Once the top lock rod has been removed, the
hinge pivot can easily be removed from the hinge
assembly on the upper left and set aside.
upper hinge
assembly
9. Remove the side loc rod.
Remove the side lock rod from
the lower hinge bracket by lifting
the top end of the rod and sliding
it toward the top of the door. The
spring should remain attached to
the lock rod. Set the lock rod aside.
Spring
10. Remove the top loc rod.
upper hinge
pivot
12. Reverse the upper hinge assembly and hinge
filler.
Lift out the upper hinge filler (on the right) and set it
aside.
Carefully lift the upper hinge assembly (on the left)
out of the outer door frame, using a small flat blade
screwdriver if necessary. Rotate the hinge assembly
180 degrees and install it on the upper right side of
the outer door. You will need to press firmly to install
the hinge assembly.
The hinge pivot removed in step 11 ill be installed
later.
a. Slide the lock rod to the right to remove it from the
hinge assembly on the left side.
upper hinge assembly
upper hinge pivot
MFL67731050_en_141213.indd 18
2014.12.13 5:21:32 PM
INSTALLATION INSTRUCTIONS
19
Reversing the Door (cont.)
upper hinge filler
13. Reinstall the top loc rod.
Rotate the top lock rod (removed in step 10) 180
degrees end for end from its original position and
reinstall it. The spring should now be to the right of
center, with the spring on the side of the rod facing
the top of the door.
b. Rotate the lo er hinge assembly 180 degrees and
install it on the right side using the two screws
removed in step a.
screws
ENGLISH
No rotate the hinge filler 180 degrees and install it
on the upper left side of the door.
lower hinge assembly
c. Flip over the lower hinge bracket and release the
tabs on the back locking the hinge filler to the hinge
bracket.
a. Insert the right end of the lock rod into the right
hinge assembly. Make sure the rod is aligned with
the guides in the door panel.
tabs
d. Rotate the hinge filler 180 degrees and snap it back
onto the FRONT of the hinge bracket facing in the
opposite direction.
b. Lower the rod into position, sliding it to bypass the
center handle, making sure to align the lock rod
with the guides all the way across the door panel.
When released, the lock rod should slide completely
into the hinge assembly on the right. Slide the
lock rod back and forth to make sure it is correctly
positioned in the guides and slides easily.
14. Reverse the lo er hinge brac et and hinge
assembly.
a. Remove the screw from the lower hinge bracket (on
the right) and lift the hinge bracket out. Set it aside.
Remove the two screws from the lower hinge assembly
on the bottom left and lift the hinge assembly out.
MFL67731050_en_141213.indd 19
e. Mount the lower hinge bracket and the filler on the
left side of the door with the screw removed in step a.
screw
15. Install the side loc rod.
Flip the side lock rod over and install it on the
opposite side. Insert the lower end into the left
hinge and lower the rod into the guides on the door
while compressing the spring inside the recess.
2014.12.13 5:21:36 PM
20
INSTALLATION INSTRUCTIONS
Reversing the Door (cont.)
Make sure the top of the side lock rod is beside the top
lock rod and the two do not overlap each other, so the
two rods can interact correctly. If they are not aligned
properly, the door will not operate properly.
interlock
buttons
bumpers
16. Reinstall the top interloc buttons.
Reinstall the top gray interlock buttons removed in
step 7, one on each side of the outer door panel.
17. Reinstall the side interloc button.
Reinstall the side interlock button removed in step 8.
Center the spring in the compartment and insert the
interlock button on top of it.
19. No , pic up the upper hinge pivot removed earlier and
rotate it 180 degrees. Press in the side interlock button
on the left side and hold it down while you press the hinge
pivot into the hinge assembly on the top right side. If the
door has been reassembled correctly, the lock rod will slide
back easily and lock the pivot in place. The door is now
ready to remount on the opposite side of the dryer.
wWARNING
Be sure to support the eight of the door before installing
the hinge screws.
18. Reinstall the door cover.
Clean the glass on the door and door cover, if
necessary.
Make sure the three gray interlock buttons are
properly installed and that the top and side lock
rods are properly aligned where they meet. Carefully
lower the door cover into place, aligning the holes in
the cover with the interlock buttons on the top and
side and the bumpers on the bottom. Take care not
to dislodge the lock rods while mounting the door
cover. Once the door cover is in place, secure it with
the 12 scre s removed in step 4.
The ten similar screws go around the top and sides
of the door cover. Make sure to install the two
different screws on the bottom edge, in the locations
marked below
MFL67731050_en_141213.indd 20
20. Reinstall the door.
While supporting the door, install the four hinge screws
removed in step 2. Test the s ing of the door to make sure
the hinges and latch are properly aligned and that the
door opens, closes and latches properly in both directions.
Two large
screws
Two small
screws
If the door doesn’t operate smoothly, remove the door
and then the door cover to check that the lock rods and
interlock buttons are properly mounted and aligned.
The interlock buttons should be oriented correctly and
operating smoothly. The interlock rods should be in the
proper position and should not overlap at the contact
point. (See steps 13-15.)
If the door is damaged, or if the door does not work after
reassembly, contact the call center at 1-800-243-0000.
2014.12.13 5:21:38 PM
INSTALLATION INSTRUCTIONS
21
Installing the Side Vent Kit
• Use a heavy metal vent.
• Do not use plastic or thin foil duct.
• Clean old ducts before installing this dryer.
• To reduce the ris of injury to persons, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
• Failure to follow all of the safety warnings in this
manual could result in property damage, injury to
persons, or death.
3. Preassemble a 4 inches (10.2 cm) elbo to the next
4-inches (10.2 cm) duct section, and secure all joints
ith duct tape. Be sure that the male end of the
elbow faces AWAY from the dryer. Insert the elbow/
duct assembly through the side opening and press it
onto the adapter duct. Secure in place with duct tape.
Be sure that the male end of the duct protrudes 12/4
inches (3.8 cm) to connect the remaining duct ork.
Attach cover plate to the back of the dryer with
included screw.
ENGLISH
wWARNING
Your new dryer is shipped to vent to the rear. It can also
be configured to vent to the bottom or side (right-side
venting is not available on gas models).
An adapter kit, part number 383EEL9001B, may be
purchased from your LG retailer. This kit contains the
necessary duct components to change the dryer vent
location.
Cover
Plate
Elbow
1. Remove the rear exhaust duct retaining scre . Pull
out the exhaust duct.
Retaining
Screw
12/4”
(3.8 cm)
OpTION 2: bOTTOM VENTING
2. Press the adapter duct onto the blo er housing and
secure to the base of the dryer as shown.
Adapter
Duct
Rear
Exhaust Duct
Bracket
OpTION 1: SIDE VENTING
2. Press the tabs on the knockout and carefully remove
the knockout for the desired vent opening (rightside venting is not available on gas models). Press the
adapter duct onto the blower housing and secure to
the base of the dryer as shown.
3. Insert the 4 inches (10.2 cm) elbo through the rear
opening and press it onto the adapter duct. Be sure
that the male end of the elbow faces down through
hole in the bottom of the dryer. Secure in place with
duct tape. Attach the cover plate to the back of the
dryer with included screw.
Adapter
Duct
Cover
Plate
Bracket
Knockout
MFL67731050_en_141213.indd 21
Elbow
2014.12.13 5:21:40 PM
22
INSTALLATION INSTRUCTIONS
Venting the Dryer
wWARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Do not crush or collapse duct or . Failure to follow
these instructions can result in fire or death.
• Do not allo duct or to rest on or contact sharp
objects. Failure to follow these instructions can result
in fire or death.
• If connecting to existing duct or , ma e sure it
is suitable and clean before installing the dryer.
Failure to follow these instructions can result in fire or
death.
• Venting must conform to local building codes.
Failure to follow these instructions can result in fire or
death.
• Gas dryers MUST exhaust to the outdoors. Failure to
follow these instructions can result in fire or death.
• Use only 4-inch (10.2 cm) rigid or flexible metal
duct or inside the dryer cabinet and for venting
outside. Failure to follow these instructions can result
in fire or death.
• To reduce the ris of fire, combustion, or
accumulation of combustible gases, DO NOT
exhaust dryer air into an enclosed and unventilated
area, such as an attic, all, ceiling, cra l space,
chimney, gas vent, or concealed space of a building.
Failure to follow these instructions can result in fire or
death.
• To reduce the ris of fire, DO NOT exhaust the dryer
ith plastic or thin foil ducting. Failure to follow
these instructions can result in fire or death.
• Rigid or semirigid metal ducting is recommended
for use bet een the dryer and the all. In special
installations hen it is impossible to ma e a
connection ith the above recommendations, a ULlisted flexible metal transition duct may be used
bet een the dryer and all connection only. The
use of this ducting ill affect drying time. Failure to
follow these instructions can result in fire or death.
• DO NOT use sheet metal scre s or other fasteners
hich extend into the duct that could catch lint
and reduce the effi ciency of the exhaust system.
Secure all joints ith duct tape. Failure to follow
these instructions can result in fire or death.
• Duct or is not provided ith the dryer. You
should obtain the necessary duct or locally. The
end cap should have hinged dampers to prevent
bac draft hen the dryer is not in use. Failure to
follow these instructions can result in fire or death.
• The total length of flexible metal duct shall not
exceed 8 ft. (2.4 m).
• In Canada, only those foil-type flexible ducts,
if any, specifically identified for use ith the
appliance by the manufacturer shall be used. In the
United States, only those foil-type flexible ducts, if any,
specifically identified for use with the appliance by the
manufacturer and that comply with the Outline for
Clothes Dryer Transition Duct, Subject 2158A, shall be
used.
• The exhaust duct must be 4 inches (10.2 cm) in
diameter ith no obstructions. The exhaust duct
should be ept as short as possible. Ma e sure
to clean any old ducts before installing your ne
dryer. Failure to follow these instructions can result in
fire or death.
MFL67731050_en_141213.indd 22
2014.12.13 5:21:40 PM
INSTALLATION INSTRUCTIONS
23
Venting the Dryer (cont.)
WALL CAp TYpE
NUMbER OF
90 ELbOWS
MAxIMUM LENGTH OF
4 INCH DIAMETER
RIGID METAL DUCT
Recommended
0
65 ft. (19.8 m)
1
55 ft. (16.8 m)
2
47 ft. (14.3 m)
3
36 ft. (11.0 m)
4
28 ft. (8.5 m)
0
55 ft. (16.8 m)
1
47 ft. (14.3 m )
2
41 ft. (12.5 m)
3
30 ft. (9.1 m)
4
22 ft. (6.7 m)
4”
(10.2 cm)
4”
(10.2 cm)
Use only for
short run
installations
12/4”
(6.35 cm)
CORRECT VENTING
ENGLISH
Ductwork
INCORRECT VENTING
NOTE
Deduct 6 ft. (1.8 m) for each additional elbo . It is not
recommended to use more than four 90° elbo s.
Routing and Connecting Ductwork
NOTE
Follow the guidelines below to maximize drying
performance and reduce lint buildup and
condensation in the ductwork.
Ductwork and fittings are NOT included and must be
purchased separately.
• Use 4-inch (10.2 cm) diameter rigid or semirigid
metal ductwork.
• The exhaust duct run should be as short as possible.
• Use as fe elbo joints as possible.
• The male end of each section of exhaust duct must
point away from the dryer.
• Use duct tape on all duct joints.
• Insulate duct ork that runs through unheated areas
in order to reduce condensation and lint buildup on
duct surfaces.
• Incorrect or inadequate exhaust systems are not
covered by the dryer warranty. Failures or poor
performance caused by such exhaust systems will
not be covered by the dryer warranty.
MFL67731050_en_141213.indd 23
2014.12.13 5:21:42 PM
24
INSTALLATION INSTRUCTIONS
Connecting Inlet Hose
The dryer must be connected to the cold water tap using the new water supply hose. Do not use old hoses
NOTE
• Water supply pressure must be bet een 21.8 PSI and 116 PSI (150~800 kPa).
• Do not strip or cross-thread hen connecting inlet hose to the valve.
• If the ater supply pressure is more than 800 kPa, a decompression device should be installed.
• Periodically check the condition of the hose and replace the hose if necessary.
• Replace inlet hoses after 5 years of use to reduce the risk of hose failure.
• Record hose installation or replacement dates on the hoses for future reference.
1. Check rubber seal in the inlet hose. T o rubber seals
are supplied with each inlet hose. They are used for
preventing water leaks. Make sure the connection to
the cold water tap is tight.
Hose
connector
3. Connect the hose to the dryer.
• Connect the ater supply hose to the dryer inlet valve
tightly by hand and then tighten another 2/3 turn ith
pliers.
Make sure that there are no kinks in the hoses and that
they are not crushed.
Rubber
seal
Y connector
2. Check the installation type.
Short
hose
Long
hose
4. Turn on the cold ater faucet.
Y connector
WITH WASHER
WITHOUT WASHER
Connect all ater supply hoses tightly by hand and
then tighten another 2/3 turn ith pliers.
WITH WASHER: When connecting the dryer to the
same faucet as a asher.
a. Shut off the cold water tap and remove the washer hose.
b. Connect the short hose to the Y-connector using one
of the hose washers.
c. Connect the other end of the short hose to the cold
water faucet.
5. Check for leaks at the Y-connector (if used) and in all
hoses.
d. Connect the long dryer hose to one side of theY-connector
and connect the washer hose to the other side.
WITHOUT WASHER: If the dryer does not share the
cold ater tap ith a asher.
a. Connect the straight end of the long hose to the cold
water faucet.
NOTE
• Before connecting the ater line to the dryer, ush
several gallons of water into a drain or bucket. This will
help prevent foreign particles such as sand and scale
from clogging the dryer inlet valve.
• Do not overtighten. Damage to the coupling can result.
MFL67731050_en_141213.indd 24
NOTE
• If any leaks are found, shut o the ater faucet,
remove the hose and check the condition of the
hose washer.
2014.12.13 5:21:44 PM
INSTALLATION INSTRUCTIONS
25
Connecting Gas Dryers
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• Gas supply requirements:
As shipped from the factory, this dryer is
configured for use ith natural gas. It can be
converted for use ith Lp (Liquefied propane) gas.
Gas pressure must not exceed 13 inches of ater
column.
• A qualified service or gas company technician must
connect the dryer to the gas service.
Failure to do so can result in fire, explosion, or death.
• Isolate the dryer from the gas supply system by
closing its individual manual shutoff valve during
any pressure testing of the gas supply. Failure to do
so can result in fire, explosion, or death.
• Supply line requirements:
Your laundry room must have a rigid gas
supply line to your dryer. In the United States,
an individual manual shutoff valve MUST be
installed ithin at least 6 ft. (1.8 m) of the dryer,
in accordance ith the National Fuel Gas Code
ANSI Z223.1 or Canadian gas installation code CSA
B149.1. A 1 - inch NpT pipe plug must be installed.
Failure to do so can result in fire, explosion, or death.
• If using a rigid pipe, the rigid pipe should be
- inch IpS. If acceptable under local codes and
ordinances and hen acceptable to your gas
supplier, 3 - inch approved tubing may be used
here lengths are less than 20 ft. (6.1 m). Larger
tubing should be used for lengths in excess of 20 ft.
(6.1 m). Failure to do so can result in fire, explosion, or
death.
ENGLISH
wWARNING
• Connect the dryer to the type of gas sho n on
the nameplate. Failure to do so can result in fire,
explosion, or death.
• To prevent contamination of the gas valve,
purge the gas supply of air and sediment before
connecting the gas supply to the dryer. before
tightening the connection bet een the gas supply
and the dryer, purge remaining air until the odor
of gas is detected. Failure to do so can result in fire,
explosion, or death.
• DO NOT use an open flame to inspect for gas lea s.
Use a noncorrosive lea -detection fluid. Failure to
do so can result in fire, explosion, or death.
• Use only a ne AGA- or CSA-certified gas supply
line ith flexible stainless steel connectors. Failure
to do so can result in fire, explosion, or death.
• Securely tighten all gas connections. Failure to do
so can result in fire, explosion, or death.
• DO NOT attempt any disassembly of the dryer
any disassembly requires the attention and tools
of an authorized and qualified service person or
company. Failure to do so can result in fire, explosion,
or death.
• Use a pipe-joint compound that is insoluble in
Liquefied petroleum (Lp) gas on all pipe threads.
Failure to do so can result in fire, explosion, or death.
Electrical requirements for gas models only
wWARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions,
including the following:
• This dryer must be plugged into a 60 Hz, 120 VAC,
• Do not, under any circumstances, cut or remove the
grounded outlet protected by a 15-ampere fuse
third (ground) prong from the po er cord. Failure
or circuit brea er. Failure to follow this warning can
to follow this warning can result in fire, explosion, or
result in fire, explosion, or death.
death.
• For personal safety, this dryer must be properly
grounded. Failure to follow this warning can result in
fire, explosion, or death.
• The po er cord of this dryer is equipped ith
a 3-prong (grounding) plug hich mates ith
a standard 3-prong (grounding) all outlet to
minimize the possibility of electric shoc hazard
from this appliance. Failure to follow this warning
can result in fire, explosion, or death.
MFL67731050_en_141213.indd 25
• Where a standard 2-prong all outlet is
encountered, it is your personal responsibility
and obligation to have it replaced ith a properly
grounded 3-prong all outlet. Failure to follow this
warning can result in fire, explosion, or death.
2014.12.13 5:21:44 PM
26
INSTALLATION INSTRUCTIONS
Connecting Gas Dryers (cont.)
wWARNING
Connecting the gas supply
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
1. Make sure that the gas supply to the laundry room is
turned OFF. Confirm that the type of gas available in
your laundry room is appropriate for the dryer. The
dryer is prepared for Natural Gas with a 3⁄8 - inch NPT
gas connection.
• Installation and service must be performed by
a qualified installer, service agency, or the gas
supplier. Failure to do so can result in fire, explosion,
or death.
• Use only a ne stainless steel flexible connector
and a ne AGA-certified connector. Failure to do so
can result in fire, explosion, or death.
• A gas shutoff valve must be installed ithin 6 ft.
(1.8 m) of the dryer. Failure to do so can result in fire,
explosion, or death.
• The dryer is configured for Natural Gas hen
shipped from the factory. Ma e sure that the dryer
is equipped ith the correct burner orifice for the
type of gas being used (Natural Gas or Liquefied
petroleum). Failure to do so can result in fire,
explosion, or death.
• If necessary, the correct orifice (For the Lp orifice
it, order part number 383EEL3002D) should be
installed by a qualified technician and the change
should be noted on the dryer. Failure to do so can
result in fire, explosion, or death.
2. Remove the shipping cap from the gas connection
at the back of the dryer. Be careful not to damage
the threads of the gas connector when removing the
shipping cap.
3. Connect the dryer to your laundry room’s gas supply
using a new flexible stainless steel connector with a 3⁄8
- inch NPT fitting.
4. Securely tighten all connections bet een the
dryer and your laundry room’s gas supply. Turn on
your laundry room’s gas supply and check all pipe
connections (both internal and external) for gas leaks
with a noncorrosive leak-detection fluid.
Electrical connection
Plug dryer into a 120 VAC,
60 Hz grounded 3-prong
outlet.
• All connections must be in accordance ith local
codes and regulations. Failure to do so can result in
fire, explosion, or death.
• Gas dryers MUST exhaust to the outdoors. Failure to
do so can result in fire, explosion, or death.
3/8” NPT Gas
Connection
AGA/CSA-Certified
Stainless Steel Flexible
Connector
1/8” NPT Pipe
Plug
Gas Supply
Shutoff Valve
High-altitude installations
The BTU rating of this dryer is AGA-certified for
elevations belo 10,000 feet.
If your gas dryer is being installed at an elevation above
10,000 feet, it must be derated by a qualified technician
or gas supplier.
MFL67731050_en_141213.indd 26
2014.12.13 5:21:45 PM
INSTALLATION INSTRUCTIONS
27
Connecting Electric Dryers
wWARNING
To help prevent fire, electric shock, serious injury,
or death, the wiring and grounding must conform
to the latest edition of the National Electrical Code,
ANSI/NFPA 70 and all applicable local regulations.
Please contact a qualified electrician to check your
home’s wiring and fuses to ensure that your home has
adequate electrical power to operate the dryer.
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
Electrical requirements for electric models only
wWARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• This dryer must be connected to a grounded
metal, permanent iring system, or an equipmentgrounding conductor must be run ith the circuit
conductors and connected to the equipmentgrounding terminal or lead on the dryer. Failure to
do so can result in fire, explosion, or death.
• The dryer has its o n terminal bloc that must
be connected to a separate 230 VAC, 60-Hertz,
single-phase circuit, fused at 30 amperes (the
circuit must be fused on both sides of the line).
ELECTRICAL SERVICE FOR THE DRYER SHOULD bE
OF THE MAxIMUM RATE VOLTAGE LISTED ON THE
NAMEpLATE. DO NOT CONNECT DRYER TO 110-,
115-, OR 120-VOLT CIRCUIT. Failure to follow these
instructions can result in fire, explosion, or death.
ENGLISH
wWARNING
• Do not modify the plug and internal ire provided
ith the dryer.
• The dryer should be connected to 4-hole outlet.
• If it does not fit the outlet, a proper outlet ill
need to be installed by a qualified electrician.
wWARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• Any installation in a manufactured or mobile
home must comply ith the Manufactured Home
Construction and Safety Standards Title 24 CFR,
part 3280 or Standard CAN/ CSA Z240 MH and
local codes and ordinances.
• A 4- ire connection is required for all mobile and
manufactured home installations, as ell as all
ne construction after January 1, 1996. Failure to
do so can result in fire, explosion, or death.
• If branch circuit to dryer is 15 ft. (4.5 m) or less in
length, use UL (Under riters Laboratories) listed
No.-10 AWG ire (copper ire only), or as required
by local codes. If over 15 ft. (4.5 m), use UL-listed
No.-8 AWG ire (copper ire only), or as required
by local codes. Allo sufficient slac in iring
so dryer can be moved from its normal location
hen necessary. Failure to do so can result in fire,
explosion, or death.
• The po er cord (pigtail) connection bet een
all receptacle and dryer terminal bloc IS NOT
supplied ith dryer. Type of pigtail and gauge
of ire must conform to local codes and ith
instructions on the follo ing pages. Failure to
follow these instructions can result in fire, explosion,
or death.
• A 4- ire connection is required for all mobile and
manufactured home installations, as ell as all
ne construction after January 1, 1996. A 4- ire
connection must be used here local codes do not
permit grounding through the neutral ire. Failure
to do so can result in fire, explosion, or death.
MFL67731050_en_141213.indd 27
2014.12.13 5:21:45 PM
28
INSTALLATION INSTRUCTIONS
Special Requirements for
Manufactured or Mobile Homes
Any installation in a manufactured or mobile home must
comply with the Manufactured Home Construction and
Safety Standards Title 24 CFR, Part 3280 or Standard
CAN/CSA Z240 MH and local codes and ordinances. If
you are uncertain whether your proposed installation
will comply with these standards, please contact a
service and installation professional for assistance.
• A gas dryer must be permanently attached to the floor.
• The electrical connection for an electric dryer must
be a 4- ire connection. More detailed information
concerning the electrical connection is provided in the
section Connecting Electric Dryers.
• To reduce the risk of combustion and fire, the dryer
must be vented to the outside.
• DO NOT vent the dryer under a manufactured home or
mobile home.
• Electric dryers may be vented to the outside using the
back, left, right, or bottom panel.
• Gas dryers may be vented to the outside using the
back, left, or bottom panel. Gas dryers may not be
vented to the outside using the right side panel
because of the burner housing.
• The dryer exhaust duct must be affixed securely to
the manufactured or mobile home structure, and the
exhaust duct must be made of a material that will resist
fire and combustion.
It is recommended that you use a rigid or flexible metal
duct.
• DO NOT connect the dryer exhaust duct to any other
duct, vent, chimney, or other exhaust duct.
• Make sure the dryer has adequate access to outside
fresh air to ensure proper operation. The opening for
outside fresh air must be at least 25 in2 (163 cm2).
• It is important that the clearance of the duct from any
combustible construction be at least 2 inches (5 cm),
and when venting the dryer to the outdoors, the dryer
can be installed ith a clearance of 1 inch (2.5 cm) at
the sides and back of the dryer.
Final Installation Check
Once you have completed the installation of the dryer
and it is in its final location, confirm proper operation
with the following tests and Installation Test (Duct
Check) on the following page.
Testing dryer heating
GAS MODELS
Close the dryer door, press the ON/OFF button to turn
the dryer on, and start the dryer on a heat setting.
When the dryer starts, the igniter should ignite the main
burner.
NOTE
If all air is not purged from the gas line, the gas igniter
may turn off before the main burner ignites. If this
happens, the igniter will reattempt gas ignition after
approximately two minutes.
ELECTRIC MODELS
Close the dryer door, press the ON/OFF button to turn
the dryer on, and start the dryer on a heat setting. The
exhaust air should be warm after the dryer has been
operating for 3 minutes.
Checking airflow
Effective dryer operation requires proper airflow.
The adequacy of the airflow can be measured by
evaluating the static pressure. Static pressure in the
exhaust duct can be measured with a manometer,
placed on the exhaust duct approximately 2 ft. (60.9 cm)
from the dryer.
Static pressure in the exhaust duct should not exceed 0.6
inches (1.5 cm). The dryer should be checked hile the
dryer is running with no load.
Checking levelness
Once the dryer is in its final location, recheck the dryer
to be sure it is level. Make sure it is level front to back
and side to side, and that all 4 leveling feet are firmly on
the floor.
• Please be a are that venting materials are not supplied
with the dryer. You should obtain the venting materials
necessary for proper installation.
MFL67731050_en_141213.indd 28
2014.12.13 5:21:46 PM
D
INSTALLATION INSTRUCTIONS
G
F
E
29
A
Installation Test (Duct check)
• Your dryer features Flo Sense , an innovative sensing
system that automatically detects blockages and
restrictions in dryer duct ork. Keeping duct ork clean
of lint buildup and free of restrictions allows clothes to
dry faster and reduces energy use.
F
NOTE
A
D
The dryer should be cool before starting this test. If
the dryer was warmed up during installation, run the
AIR DRY cycle for a few minutes to reduce the interior
temperature.
To activate the installation test:
1. Remove the literature, and then close the door.
Do not load anything in the drum for this test, as in
may affect the accuracy of the results.
H
B
4. Chec the display for results.
During the three minute test cycle, monitor the
Flow Sense™ display on the control panel. If no bars
are displayed, when the cycle ends, the exhaust
system is adequate. If the exhaust system is severely
restricted, the display will show four bars. Other
problems may also be shown with error codes. Refer
to the next page for error code details and solutions.
E
H
NO BARS:
OK
B
ENGLISH
Once you have completed the installation of the dryer,
use this test to make sure the condition of the exhaust
system is adequate for proper operation of the dryer.
This test should be performed to alert you to any serious
problems in the exhaust system of your home.
C
FOUR BARS:
RESTRICTED
Four bars indicates that the exhaust system is severely
restricted. Have the system checked immediately, as
performance will be poor.
5. End of cycle.
At the end of the test cycle,
will display.
The test cycle will end and the dryer will shut off
automatically after a short delay.
C
2. press and hold the Temp.Control and Signal
buttons and then press the pOWER button.
This button sequence activates the installation test.
The code
will display if the activation is
successful.
3. press START/pAUSE button.
The dryer will start the test, which will last about
two minutes. The heat will be turned on and the
temperatures in the drum will be measured.
MFL67731050_en_141213.indd 29
2014.12.13 5:21:52 PM
30
INSTALLATION INSTRUCTIONS
Installation Test (Duct check) (cont.)
• Check the error code before you call for service
Error Code
tE1 or tE2
HS
pS or pF or np
Possible Causes
Solutions
• Temperature sensor failure
• Turn o the dryer and call for
service.
• Humidity sensor failure.
• Turn o the dryer and call for
service.
• Electric dryer po er cord is not
connected correctly, or house power
supply is incorrect.
• Check the power supply or the
connection of power cord to the
terminal block. Refer to the
Connecting electric dryers section of this manual
for complete instructions.
• Reset circuit breaker or replace fuse. Do not increase
the fuse capacity.
If the problem is a circuit overload, have it corrected
by a qualified electrician.
• House fuse is blo n, circuit breaker has
tripped, or power outage has occurred.
• Chec the duct condition
If the test displays four bars, check the exhaust system
for restrictions and damage. Repair or replace the
exhaust system as needed.
Restricted or bloc ed airflo
Avoid long runs or runs with multiple elbows or
bends.
NOTE
When the dryer is first installed, this test should be
performed to alert you to any existing problems with
the exhaust duct in your home. However, since the
test performed during normal operation provides
more accurate information on the condition of the
exhaust duct than does the installation test, the
number of bars displayed during the two tests may
not be the same.
Do not interrupt the test cycle, as this could result in
the wrong results.
Even if no bars are displayed during the test cycle,
some restrictions may still be present in the exhaust
system. Refer to the Venting the Dryer section of
this manual for complete exhaust system and venting
requirements.
Your dryer features Flow Sense™, an innovative
sensing system that automatically detects blockages
and restrictions in dryer duct ork. Keeping duct ork
clean of lint buildup and free of restrictions allows
clothes to dry faster and reduces energy use.
Excess or crushed
transition duct
Too many elbows or
exhaust too long
Check for blockages and lint buildup.
Lint buildup
or blockage
Make sure the ductwork is not crushed or restricted.
Crushed or
damaged
exhaust
MFL67731050_en_141213.indd 30
2014.12.13 5:21:55 PM
H
B
C
HOW TO USE
31
A
E
HOW TO USE
H
B
C
ENGLISH
D
E
Operating the Dryer
A
Clean the Lint Filter
1
H
B
C
Lint
Filter
Load the Dryer
2
H
If the lint filter has not already been cleaned, lift out the filter and remove the
lint from the last load. This will help ensure the fastest and most efficient drying
performance.
B
C
3
Load the dryer with the wet laundry from the washer. If the load is extra large,
you may need to divide it into smaller loads for proper performance and fabric
care.
Turn On the Dryer
Press the POWER button to turn on the dryer. The cycle LEDs will illuminate
and a signal ill sound, if turned on. Refer to page 10.
4
Select a Cycle
Press the Cycle buttons until the indicator for the desired cycle is lit.
The preset temperature, dry level, and option settings for that cycle will be
shown. Default settings for the selected cycle can now be changed if desired.
Refer to the Cycle Setting and Options page for details.
NOTE
Not all options or modifiers are available on all cycles. Refer to the Cycle
Guide page for default settings and allowable options. A different chime will
sound and the LED will not come on if the selection is not allowed.
5
begin the cycle
Press the START/PAUSE button to begin the cycle. The cycle can be paused at
any time either by opening the door or by pressing the START/PAUSE button. If
the cycle is not restarted ithin 4 minutes, the dryer ill shut off and the cycle
settings will be lost.
6
End of Cycle
When the cycle is finished, the chime will sound if it is set. Remove your
clothing from the dryer immediately to reduce wrinkling. If Wrinkle Care is
selected, the dryer will tumble briefly every few minutes to help prevent
wrinkles from setting in the clothes.
MFL67731050_en_141213.indd 31
2014.12.13 5:22:2 PM
32
HOW TO USE
Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for
more detailed information.
Sorting Loads
Check the Lint Filter Before Every
Load
Fabric care labels
Most articles of clothing feature fabric care labels that
include instructions for proper care.
To clean, pull the lint filter straight up and roll any lint
off the filter with your fingers. Do not rinse or wash the
filter to remove lint. Push the lint filter firmly back into
place. See Regular Cleaning for more information.
Fabric care labels
Tumble
Tumble
dry
dry
Dry
Dry
Gentle/
Gentle/
delicate
delicate
Heat
setting
Always make sure the lint filter is clean before starting a
new load; a clogged lint filter will increase drying times.
Normal
Normal
Permanent Press/
Permanent
Press/
wrinkle resistant
wrinkle resistant
Always ensure the lint filter is properly installed before
running the dryer. Running the dryer with a loose or
missing lint filter will damage the dryer and articles in
the dryer.
Do not dry
Do not tumble dry (used
Do not dry
Do not tumble dry (used with
with
do not wash)
do not wash)
High
Medium
Low
No heat/air
Grouping similar items
For best results, sort clothes into loads that can be dried
with the same drying cycle.
Different fabrics have different care requirements, and
some fabrics will dry more quickly than others.
Loading the Dryer
Lint
Filter
wWARNING
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• Chec all poc ets to ma e sure that they are
empty. Items such as clips, pens, coins, and eys
can damage both your dryer and your clothes.
Flammable objects such as lighters or matches
could ignite, causing a fire. Failure to do so can result
in fire, explosion, or death.
• Never dry clothes that have been exposed to oil,
gasoline, or other flammable substances. Washing
clothes ill not completely remove oil residues.
Failure to obey this warning can result in fire, explosion,
or death.
NOTE
Loading tips
• Combine large and small items in a load.
• Damp clothes ill expand as they dry. Do not
overload the dryer; clothes require room to tumble
dry properly.
• Close zippers, hooks, and dra strings to prevent
these items from snagging or tangling on other
clothes.
MFL67731050_en_141213.indd 32
2014.12.13 5:22:4 PM
HOW TO USE
33
Using the LG EasyLoad™
Hamper Door
Use the swing door when unloading, or when loading
bulkier items, for easy access to the drum.
Use the hamper door when loading. It acts as a chute, to
help guide items into the drum and help prevent items
from falling onto the floor. It also comes in handy when
unloading a few small items, helping prevent the rest of
the laundry from being pulled onto the floor.
To open the swing door, insert your fingers into the
handle recess on the top of the door on the side
opposite the hinge and pull the door open.
NOTE
Make sure the hamper door release is completely
closed before using the swing door.
ENGLISH
S ing Door
To open the hamper door, press the release in the
middle of the handle recess on the top of the door and
pull the door forward.
Make sure laundry is fully inserted in the drum before
closing the door.
NOTE
Make sure the swing door latch is completely closed
before pressing the hamper door release.
Hamper door latch
Swing door
Interlock
Buttons
Hamper door
wWARNING
When the door is opened if you press the three interlock
buttons, door may fall off.
Failure to follow this warning can cause serious injury.
wWARNING
• Do not place heavy items on or lean against the top
of the door hen it is open.
• Do not attempt to pull the hamper door open more
than 40 degrees.
wWARNING
• Be careful hen opening and closing the door. Fingers
and hands can get caught in the door and cause injury
if the door drops forward unexpectedly.
The dryer could tip forward, causing injury or damage.
MFL67731050_en_141213.indd 33
2014.12.13 5:22:7 PM
34
HOW TO USE
Cycle Guide
= default setting

Type
STEAM
CYCLE
Cycle
Fabric Type
MANUAL
DRY
Time
in Min.
More
Time/ Wrin le Damp
Dry Energy
Less
Care
Saver
Signal
Time
Steam
FreshTM
Comforter, Shirts,
Trousers (except
especially delicate
fabrics)
Off
High
14

Wrinkle
Free
Comforter, Bedding,
Children’s clothing
Off
High
18

High
54


Low
32


Medium
Elec. : 67
Gas : 76


Low
28


Medium
High
55


Medium
55
High
70
High
25
Heavy Duty Jeans,
heavyweight items
SENSOR
DRY
Dry Level Temperature
= allowable option
Normal Dry
Adjustable
Perm.Press
Permanent press,
synthetic items
Normal Dry
Normal
Work clothes,
corduroys, etc.
Normal Dry
Delicates
Lingerie, sheets,
blouses
Normal Dry
Towels
Denims, towels,
heavy cottons
Normal Dry
Bulky
Comforters,
Pillows, shirts
Normal Dry
Anti
Bacterial
Do not use this cycle
with delicate fabrics.
Very
Dry
Speed Dry
For small loads with
short drying times
Off
Air Dry
For items that require
heat-free drying such
as plastics or rubber
Off
Time Dry
For loads that require
a specific dry time.
Off
Adjustable
Adjustable
Adjustable
Adjustable
Adjustable
Sensor dry cycles
Sensor dry cycles utilize LG’s unique dual sensor
system to detect and compare the moisture level
in clothes and in the air and adjust the drying time
as needed to ensure superior results. The dryer
automatically sets the dryness level and temperature
at the recommended setting for each cycle. The
estimated time remaining will be shown in the display.
NOTE
To protect your garments not every dryness level,
temperature, or option is available with every cycle.
See the Cycle Guide for details.
Adjustable Adjustable
No Heat
High
30
Adjustable
40
Adjustable Adjustable








Manual dry cycles
Use manual dry cycles to select a specific amount of
drying time and a drying temperature. When a manual
dry cycle is selected, the ESTIMATED TIME REMAINING
display shows the actual time remaining in your cycle.
You can change the actual time in the cycle by
pressing More Time or Less Time.
Certified by NSF
NSF International (formerly the National
Sanitation Foundation), certifies that Anti
Bacterial cycle reduces 99.9% of bacteria
on laundry, and none of bacteria will carry
over onto the next laundry load.
NOTE
The Energy Saver option is turned on by default in the
Normal cycle.
For faster drying in the Normal cycle, turn off the
Energy Saver option.
MFL67731050_en_141213.indd 34
2014.12.13 5:22:8 PM
HOW TO USE
35
Cycle Settings And Options
NOTE
To protect your garments, not every dryness level,
temperature, or option is available with every cycle.
See the Cycle Guide for details.
Dry Level
Selects the level of dryness for the cycle. Press the Dry
Level button repeatedly to scroll through available
settings.
• This option is only available ith sensor dry cycles.
• The dryer ill automatically adjust the cycle time.
Selecting More Dry or Very Dry will increase the cycle
time, while Less Dry or Damp Dry will decrease the
cycle time.
• Use a Less Dry or Damp Dry setting for items that you
wish to iron.
Temp.Control
Adjusts the temperature setting from Low to High. This
allows precise care of your fabrics and garments. Press
the Temp.Control button repeatedly to scroll through
available settings. Temp control is not adjustable in
Sensor dry cycles.
Time Dry
Allo s you to manually select the drying time, from 20
to 60 minutes, in 10-minute increments. Use this for
small loads or to remove wrinkles. Use the More Time/
Less Time buttons to add or reduce the drying time in
1-minute increments.
Signal
Adjusts the volume of the Signal or turns off the Signal.
Press the button repeatedly until the desired volume
setting is illuminated.
Your dryer features several additional cycle options to
customize cycles to meet your individual needs. Certain
option buttons also feature a special function that can
be activated by pressing and holding that option button
for 3 seconds.
To Add Cycle Options to a Cycle:
1. Turn on the dryer and press the Cycle buttons to
select the desired cycle.
2. Use the cycle settings buttons to adjust the settings
for that cycle.
3. Press the cycle option button(s) for the option you
would like to add. A confirmation message will be
shown in the display.
4. Press the START/PAUSE button to start the cycle. The
dryer will start automatically.
MFL67731050_en_141213.indd 35
Damp Dry Signal
With this option, the dryer will signal when the load
is approximately 80% dry. This allo s you to remove
faster- drying lightweight items or items that you would
like to iron or hang while still slightly damp. Press the
Damp Dry Signal button to activate or deactivate Damp
Dry Signal.
ENGLISH
Sensor dry cycles have preset settings that are selected
automatically. Manual dry cycles have default settings,
but you may also customize the settings using the cycle
setting buttons. Press the button for that option to view
and select other settings.
Wrinkle Care
Selecting this option will tumble the load periodically for
up to 3 hours after the selected cycle, or until the door is
opened. This is helpful in preventing wrinkles when you
are unable to remove items from the dryer immediately.
Special functions
The option buttons also activate special functions,
including Child Lock and Rack Dry.
Select the option by pressing the option button. Press
and hold the option button for special features marked
with the asterisk (*), such as Child Lock.
* Rack Dry
Use RACK DRY ith items, such as ool s eaters, silk,
and lingerie, that should dry flat. Rack Dry can also be
used with items that should not be tumbled dry, such as
gym shoes or stuffed animals.
NOTE
NEVER tumble dry a load of clothing with the rack
installed. When the rack is installed, the drum will
rotate as usual, but the rack will not move. Make sure
all articles to be dried remain completely on the rack
and cannot fall off or be pulled off by the turning
drum. Be sure to remove the rack after use.
To install the drying rack:
1. With the dryer door open, slide the rack into the dryer
drum.
2. Make sure it is seated evenly on the edge of the inner
door rim and resting flat on the inside of the dryer.
2014.12.13 5:22:10 PM
36
HOW TO USE
Special Functions. (cont.)
* Child Lock
Use this option to prevent unwanted use of the dryer
or to keep cycle settings from being changed while the
dryer is operating. Press and hold the Damp Dry Signal
button for 3 seconds to activate or deactivate the Child
Lock function.
The Child Lock icon will be shown in the display, and all
controls are disabled except the POWER button.
NOTE
Once set, Child Lock remains active until it is manually
deactivated. Child Lock must be turned off to run
another cycle. To deactivate Child Lock, press and hold
the Damp Dry Signal button for three seconds.
Energy Saver
This option helps to reduce the energy consumption in
the Normal cycle, depending on the load size.
The drying time will be changed when the Energy Saver
option is selected.
NOTE
The Energy Saver option is turned on by default in the
Normal cycle.
For faster drying in the Normal cycle, turn off the
Energy Saver option.
Custom Program
If you have a special combination of settings that you
use frequently, you can save these settings as a Custom
Program..
* To Save a Custom Program:
1. Turn on the dryer and press the Cycle Buttons to select
the desired cycle.
2. Use the cycle setting buttons to adjust the settings for
that cycle.
3. Press the cycle option button(s) for the option you
would like to add.
4. Press and hold the Custom PGM button for 3 seconds.
MFL67731050_en_141213.indd 36
NOTE
You may save only one custom program at a time.
Pressing and holding the Custom PGM button will
overwrite any previously saved custom program.
To Recall a Custom Program:
1. Turn on the dryer.
2. Press the Custom PGM button.
3. Press the START/PAUSE button to start the cycle.
Steam Functions
LG’s new steam technology allows you to inject fabrics
with a swirling jet of hot steam to refresh clothes, reduce
static, and make ironing easier.
Simply select the Steam Fresh™ cycle, or you can add a
steam option to selected cycles.
Using the Steam Fresh™ cycle
Steam Fresh™ uses the power of steam alone to quickly
reduce wrinkles and odor in fabrics. It brings new life to
wrinkled clothes that have been stored for an extended
time and makes heavily wrinkled clothes easier to iron.
Steam Fresh™ can also be used to help reduce odors in
fabrics.
Using the Wrinkle Free cycle
Use to remove wrinkles, including from loads left in the
dryer too long. This is helpful in preventing wrinkles
when you are unable to remove items from the dryer
immediately.
NOTE
• If you ill be on vacation or not using your dryer
for an extended period of time, you should turn off
the water supply to the dryer. This helps to avoid
unintended flooding (due to a water pressure surge)
while you are away.
2014.12.13 5:22:10 PM
HOW TO USE
Tag on
NOTE
Depending on the smart phone manufacturer and
Android OS version, the NFC activation process may
differ. Refer to the manual of your smart phone for
details.
ENGLISH
- The Tag On function allows you to conveniently use the
LG Smart Diagnosis™ , Cycle Download, Laundry Stats
and Tag On Cycle Set features to communicate with
your appliance right from your own smart phone. To
use the Tag On functions:
1. Do nload the LG Smart Laundry&DW App to your
smart phone.
2. Turn on the NFC (Near Field Communication) function
in your smart phone.
- The Tag On function can only be used with smart
phones equipped with the NFC function and based on
the Android operating system (OS).
37
Using the Tag On Function
The Tag On icon
Turning on the Smart Phone’s NFC Function
1. Enter the Settings menu of
the smart phone and select
Share & Connect under
“WIRELESS & NETWORKS.”
Tag On position
Look for the Tag On icon next to the LED
screen on the control panel. This is where you
position your smart phone when using the
Tag On function of the LG Smart Laundry&DW
application.
2. 1 Set NFC and
Direct/Android Beam to
ON, 2 and select NFC.
1
2
1
2
1
2
3. Check the Use Read and
Write/P2P Receive option.
2
2
1
1
When you use the Tag On function, position your smart
phone so that the NFC antenna on the back of your
smart phone matches the position of the Tag On icon
on the appliance. If you do not know the position of
your NFC antenna, move your smart phone very slightly
in a circular motion until the application verifies the
connection.
Because of the characteristics of NFC, the transmission can
fail :
• if the distance is too far
• if the phone has a metal sticker or a thick case
• if the phone doesn’t support NFC
Press [
in the LG Smart Laundry&DW app for a
more detailed guide on how to use the Tag On function.
MFL67731050_en_141213.indd 37
2014.12.13 5:22:18 PM
38
HOW TO USE
Using Tag On with Applications
Touch the LG appliance’s Tag On logo with your
NFCequipped smart phone to use the LG Smart
Laundry&DW applications: LG Smart Diagnosis, Cycle
Download, Laundry Stats, and Tag on Cycle Set.
Tag On Diagnosis
1. Install the LG Smart Laundry & DW application on
a NFC-equipped smartphone.
- Install the application from the Play store and run it.
4. Touch the Tag On logo.
- When a Tag On screen
appears (see at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If it isn’t recognized, touch
] on the upper right
[
of the Tag On screen on
your LG Smart Laundry&DW
application to see the
detailed guide. (This might
happen due to the different
NFC antenna positions for
each phone.)
5. Chec the diagnosis results
and solutions.
- It shows the diagnosis results
on the cycles recently used.
2. Select Tag On.
- Select Tag On by using the
top icons or the bottom icons.
※ Images are for reference only.
The actual LG Smart Laundry&DW application may be
different.
3. Select Tag On Diagnosis.
MFL67731050_en_141213.indd 38
2014.12.13 5:22:22 PM
HOW TO USE
39
Call Center
ENGLISH
If you receive a diagnosis from either the Tag On
Diagnosis or Smart Diagnosis application that is unclear
or directs you to call the LG Service Center, follow these
instructions:
1. Select press to Call LG
Service on the Smart
Diagnosis Result screen.
2. Select your country.
3. Agree to Terms and Conditions of the Use and
privacy policy selecting I Accept.
4. Enter your phone number in the field. Use this
phone number hen tal ing to the LG customer
service representative to allo them to find your
Smart Diagnosis data.
Canada
Canada
Canada
Canada
Canada
Canada
5. press the Call button to
initiate the call to LG’s
Support Center.
1 888 542 2623
888 542
542 2623
2623
11 888
※ Images are for reference only. The actual LG Smart
Laundry&DW application may be different.
MFL67731050_en_141213.indd 39
2014.12.13 5:22:23 PM
40
HOW TO USE
Tag On Cycles Download
Tag On Cycle Download allows you to download cycles for later
use. The cycle is available at the Downloaded cycle position on
the control panel until another cycle is downloaded.
1. Install the LG Smart Laundry&DW application on a
NFC-equipped smartphone.
- Install the application from the Play store and run it.
2. Select Tag On.
- Select Tag On by using the
top icons or the bottom
icons.
3. Select Tag On Cycle
Do nload.
5 Select a cycle to do nload.
- You can also check the existing
cycles already downloaded.
6. Touch the Tag On logo.
- When a Tag On screen
appears (see at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If it isn’t recognized, touch
] on the upper right of
[
the Tag On screen on your LG
Smart Laundry&D’ application
to see the detailed guide.
(This might happen due to
the different NFC antenna
positions for each phone.)
7. The ne cycle is do nloaded
successfully
- Check the cycle at the
Downloade’ cycle position on
the control panel.
※ Images are for reference only. The actual LG Smart
Laundry&DW application may be different.
4. Touch the Tag On logo.
- When a Tag On screen
appears (see at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If it isn’t recognized, touch
] on the upper right
[
of the Tag On screen on your
LG Smart Laundry&DW’
application to see the detailed
guide. (This might happen due
to the different NFC antenna
positions for each phone.)
MFL67731050_en_141213.indd 40
2014.12.13 5:22:27 PM
HOW TO USE
Laundry Stats
FLOW SENSETM Status
LG’s Flow SenseTM duct blockage sensing system detects
and alerts you to restrictions in the installed household
ductwork that reduce exhaust airflow through the dryer.
ENGLISH
Laundry Stats can monitor the Flow Sense result in case
your home exhaust system is clogged.
Laundry Stats can also tell you details of your last ten
cycles.
1. Select Tag On by using the
top icons or the bottom
icons.
41
1. Select the FLOW SENSETM
Status in the Laundry Stats
screen.
2. Select Laundry Stats.
2. If the status sho s your
home exhaust system is
bloc ed, press the Venting
Tips button.
Refer to pages 22-23 of this
manual for more guidance
on venting the dryer.
Refer to pages 29-30 of this
manual for more information
regarding Flo SenseTM.
4. Touch the Tag On logo.
- When a Tag On screen
appears (see at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If the phone isn’t recognized,
touch [
] on the upper
right of the Tag On screen on
your LG Smart Laundry&DW
application to see the detailed
guide.(This might happen due
to the different NFC antenna
positions for each phone.)
MFL67731050_en_141213.indd 41
※ Images are for reference only. The actual LG Smart
Laundry&DW application may be different.
2014.12.13 5:22:29 PM
42
HOW TO USE
Run Cycle Again
1. Select the Run Cycle Again
button.
- The most used cycle or
most recent cycle can be
immediately started by
selecting the Run Cycle Again
button.
3. Chec
hether drying starts
ith the selected cycle.
- The screen shown at right
appears and drying starts
immediately on the selected
cycle.
2. Touch the Tag On logo.
- When a Tag On screen
appears(shown at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If the phone isn’t recognized,
] on the upper
touch [
right of the Tag On screen on
your LG Smart Laundry&DW
application to see the
detailed guide. (This might
happen due to the different
NFC antenna positions for
each phone.)
※ Images are for reference only. The actual LG Smart
Laundry&DW application may be different.
MFL67731050_en_141213.indd 42
2014.12.13 5:22:31 PM
HOW TO USE
43
Tag On Cycle Set
1. Select Tag On by using the
top icons or the bottom
icons.
2. Select Tag On Cycle Set.
3. Touch the Tag On logo.
- When a Tag On screen
appears(shown at right), tap
your smart phone on the Tag
On icon on the right side of
the dryer’s control panel.
- If the phone isn’t recognized,
] on the upper
touch [
right of the Tag On screen on
your LG Smart Laundry&DW
application to see the
detailed guide. (This might
happen due to the different
NFC antenna positions for
each phone.)
ENGLISH
Tag On Cycle Set allows you to automatically adjust the
cycle and settings based on your needs.
5. After selecting the
category, a list of specific
cycles ill appear. Select
the cycle based on your
needs.
6. When the Tag On screen
appears (sho n at right),
tap your smart phone to
the Tag On logo on the
right side of the asher’s or
dryer’s control panel.
7. After tagging the machine
ith your phone, the cycle
ill automatically start.
Verify the correct cycle and
settings ere selected.
※ Images are for reference only. The actual LG Smart
Laundry&DW application may be different.
4. Select a laundry category
based on the issue you ant
the machine to focus on.
MFL67731050_en_141213.indd 43
2014.12.13 5:22:34 PM
44
MAINTENANCE
MAINTENANCE
Regular Cleaning
wWARNING
Cleaning the lint filter
Always clean the lint from the filter after every cycle.
To reduce the risk of fire, electric shock, or injury
to persons when using this appliance, follow basic
precautions, including the following:
• Unplug the dryer before cleaning to avoid the ris
of electric shoc . Failure to follow this warning can
cause serious injury, fire, electrical shock, or death.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the asher. They will damage the
finish.
Cleaning the exterior
Proper care of your dryer can extend its life.
The outside of the machine can be cleaned with warm
water and a mild, nonabrasive household detergent.
Immediately wipe off any spills with a soft, damp cloth.
NOTE
Do not use methylated spirits, solvents, or similar
products.
Lint
Filter
To clean, open the dryer door and pull the lint filter
straight up. Then:
1. For everyday cleaning, roll any lint off the filter ith
your fingers, or
Never use steel wool or abrasive cleansers; they can
damage the surface.
Cleaning the interior
Wipe around the door opening and seal with a soft,
damp cloth to prevent lint and dust buildup that could
damage the door seal.
Clean the window with a soft cloth dampened with
warm water and a mild, nonabrasive household
detergent; then wipe dry.
The stainless steel drum can be cleaned with a
conventional stainless steel cleaner, used according to
the manufacturer’s specifications.
Never use steel wool or abrasive cleansers; they can
scratch or damage the surface.
Cleaning around and under the dryer
Vacuum lint and dust from around the dryer and
underneath it regularly. Vent ductwork should be
checked for lint buildup and cleaned at least once per
year. If any noticeable reduction in airflow or drying
performance occurs, immediately check ductwork for
obstructions and blockages.
Maintaining ductwork
Vent ductwork should be checked for lint buildup once
per month and cleaned at least once per year. If any
noticeable reduction in airflow or drying performance
occurs, immediately check ductwork for obstructions
and blockages. Contact a qualified technician or
service provider.
2. Vacuum the lint filter.
3. If the lint filter has become very dirty or clogged
with fabric softener, wash the lint filter in warm,
soapy water and allow to dry thoroughly before
reinstalling.
NOTE
NEVER operate the dryer without the lint filter in
place. NEVER operate the dryer with a wet lint filter.
MFL67731050_en_141213.indd 44
2014.12.13 5:22:35 PM
TROUBLESHOOTING
45
TROUBLESHOOTING
Your dryer is equipped with an automatic error-monitoring system to detect and diagnose problems at an early
stage. If your dryer does not function properly or does not function at all, check the following before you call for
service.
problem
possible Causes
Solutions
Dryer will not
turn on
• Po er cord is not properly
plugged in.
• House fuse is blo n, circuit
breaker has tripped, or power
outage has occurred.
• Make sure that the plug is plugged securely into a
grounded outlet matching the dryer’s rating plate.
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload, have it
corrected by a qualified electrician.
Dryer does
not heat
• House fuse is blo n, circuit
breaker has tripped, or power
outage has occurred.
• Gas supply or service turned off
(gas models only).
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload, have it
corrected by a qualified electrician.
• Confirm that the house gas shutoff and the dryer gas
shutoff are both fully open.
Greasy or dirty • Fabric softener used incorrectly.
• Clean and dirty clothes being
spots
dried together.
on clothes
• Confirm and follo the instructions provided ith your
fabric softener.
• Make sure to use your dryer to dry only clean items,
because dirty items can soil clean clothes placed in the
same or subsequent loads.
• Stains on dried clothes are actually stains that ere not
removed during the washing process.
Make sure that clothes are being completely cleaned
according to the instructions for your washer and
detergent.
Display shows
error
code tE1 or tE2
• Thermistor is malfunctioning.
Lint on clothes • Lint filter not cleaned properly.
• Laundry not sorted properly.
• Excess static in clothes.
• Dryer is overloaded.
• Tissue, paper, etc., left in pockets.
Excess static in
clothes after
drying
• Fabric softener not used or used
incorrectly.
• Clothes dried too long
(overdried).
• Drying synthetics, permanent
press, or synthetic blends.
MFL67731050_en_141213.indd 45
ENGLISH
Before Calling for Service
• Turn off the dryer and call for service.
• Make sure the lint filter is cleaned before every load. With
some loads that produce high amounts of lint, it may be
necessary to clean the filter during the cycle.
• Some fabrics are lint producers (i.e., a fuzzy hite cotton
towel) and should be dried separately from clothes that
are lint trappers (i.e., a pair of black linen pants).
• See the Excess static in clothes after drying section belo .
• Divide larger loads into smaller loads for drying.
• Check pockets thoroughly before ashing and drying
clothes.
• Use a fabric softener to reduce static electricity correctly.
Do not use fabric softeners or products to eliminate static
unless recommended by the manufacturer of the fabric
softener or product.
• Overdrying a load of laundry can cause a buildup of static
electricity. Adjust settings and use a shorter drying time,
or use SENSOR DRY cycles.
• These materials can cause static buildup. Try using a fabric
softener.
2014.12.13 5:22:36 PM
46
TROUBLESHOOTING
Before Calling for Service (cont.)
problem
Clothes are
wrinkled
possible Causes
• Clothes dried too long
(overdried).
• Clothes left in dryer too long
after cycle ends.
Solutions
• Overdrying a load of laundry can lead to rinkled clothes.
Try a shorter drying time, and remove items while they
still retain a slight amount of moisture.
• Remove items from the dryer immediately at the end
of the cycle. Use the Wrinkle Care option to continue
tumbling clothes at the end of the cycle, for up to 3 hours.
Drying time is
not consistent
• Heat settings, load size, or
dampness of clothing is not
consistent.
• The drying time for a load ill vary depending on the heat
setting, the type of heat used (electric, natural gas, or LP
gas), the size of the load, the type of fabrics, the wetness
of the clothes, and the condition of the exhaust ducts and
lint filter.
Clothes take
too long to dry
• Load is not properly sorted.
• Separate heavy items from light eight items. Larger and
heavier items take longer to dry.
• Heavy fabrics take longer to dry because they tend to
retain more moisture. To help reduce and maintain more
consistent drying times for large and heavy fabrics,
separate these items into smaller loads of a consistent
size.
• Use the appropriate control settings for the type of load
you are drying.
• Make sure the lint filter is cleaned before every load. With
some loads that produce high amounts of lint, it may be
necessary to clean the filter during the cycle.
• Confirm that the exhaust duct ork is properly configured
and free of debris, lint, and obstructions. Make sure that
outside wall dampers can open properly and are not
blocked, jammed, or damaged.
• Reset circuit breaker or replace fuse. Do not increase
fuse capacity. If the problem is a circuit overload, have it
corrected by a qualified electrician.
• Divide larger loads into smaller loads for drying.
• If you are drying a very small load, add a fe extra items
to ensure proper tumbling action.
• Large load of heavy fabrics.
• Dryer controls are not set
properly.
• Lint filter needs to be cleaned.
• Exhaust ducts blocked, dirty, or
duct run is too long.
• House fuse is blo n, circuit
breaker has tripped, or power
outage has occurred.
• Dryer is overloaded.
• Dryer is underloaded.
Clothes are
shrinking
• Garment care instructions are
not being followed.
• To avoid shrinkage, please carefully follo the fabric
care instructions for your garment, because some fabrics
will naturally shrink when washed. Other fabrics can be
washed but will shrink when dried in a dryer. Use a low or
no heat setting.
Clean Filter
light is on
during the
drying cycle
• Lint filter is almost clogged or
full.
• Pause the drying cycle and clean the lint filter.
Garments still
wrinkled after
Steam Fresh™
• Too many or too different types
of garments in dryer.
• Small loads of 1 to 5 items ork best.
• Load fe er garments. Load similar-type garments.
MFL67731050_en_141213.indd 46
2014.12.13 5:22:36 PM
TROUBLESHOOTING / SPECIFICATIONS
47
Before Calling for Service (cont.)
possible Causes
ENGLISH
problem
Solutions
There are no
creases left on
garment after
Steam Fresh™
• The function of this cycle is to
remove wrinkles from fabric.
• Use an iron to make creases.
Odors remain
in clothing after
Steam Fresh™
• Steam Fresh did not remove
odor completely.
• Fabrics containing strong odors should be ashed in a
normal cycle.
Flow Sense™
indicator
shows four
bars during the
drying cycle
• Duct ork is too long or has too
many turns/restrictions.
• Significant blockage of the
ductwork due to lint buildup or
debris.
• The appliance has detected a
restriction in the external dryer
venting.
• Install a shorter or straighter duct run. See the Installation
Instructions.
The display
shows
“d90”, “d95”
• The duct ork is about 90%-95%
blocked.
(“d90” or “d95” error code
displayed 2 hours only)
• House exhaust system blocked.
• Do not use the dryer until the exhaust system has been
cleaned and/or repaired. Using the dryer with a severely
restricted exhaust is dangerous and could result in a fire
or other property damage.
• Check the outside dryer vent hile the dryer is operating
to make sure there is strong airflow.
• If the exhaust system is extremely long, have it repaired or
rerouted.
• Keep the area around the dryer clean and free of clutter.
• Check vent hood for damage or lint clogging.
• Make sure the area around the vent hood is clear.
• Duct ork should be checked/cleaned soon.
Dryer can be used in this condition, but drying times may
be longer.
• If exhaust restrictions are sensed by the Flo Sense
system, the indicator will remain on for two hours after
the end of the cycle. Opening the door or pressing the
POWER button will turn off the display.
SPECIFICATIONS
Steam Dryer
Models
DLEY1701*E DLGY1702*E
Description
Steam Dryer
Electrical requirements
Please refer to the rating label regarding detailed information.
Gas requirements
NG 4-10.5 inches WC
LP: 8–13 inches WC (Gas Models only)
Max. water pressure
21.8 ~ 116 psi (150 ~ 800 kPa)
Dimensions
27” (W) X 28 15/16” (D) X 40 3/16” (H), 50 1/4” (D with door open)
68.6 cm (W) X 73.4 cm (D) X 102 cm (H), 127.5 cm (D ith door open)
Net weight
Gas dryer : 137.6 lbs (62.4 kg)
Electric dryer : 134.5 lbs (61 kg)
Drying capacity
- Normal cycle
MFL67731050_en_141213.indd 47
IEC 7.3 cu.ft. (22.5 lb/10.2 kg)
2014.12.13 5:22:36 PM
48
USING SMART DIAGNOSIS™
USING Smart Diagnosis™
Should you experience any problems with your dryer, it has the capability of transmitting data to your Smart Phone
using the LG Smart Laundry Application or via your telephone to the LG call center.
Smart Diagnosis™ cannot be activated unless your dryer is turned on by pressing the POWER button. If your dryer is
unable to turn on, then troubleshooting must be done without using Smart Diagnosis™.
Audible Diagnosis
Smart Diagnosis™ Using Your
Smart Phone
Smart Diagnosis™ Through the Call
Center
1. Do nload the LG Smart Laundry application on your
smart phone.
1. Call the LG call center at: (LG U.S.) 1-800-243-0000
(LG Canada) 1-888-542-2623.
2. Open the LG Smart Laundry application on your
smart phone. Press the right arrow button to advance
to the next screen.
2. When instructed to do so by the call center agent,
hold the mouthpiece of your phone over the Smart
Diagnosis™ logo on the machine. Hold the phone no
more than one inch (but not touching) the machine.
3. Press the RECORD button on the smart phone and
then hold the mouth piece of the smart phone near
the Smart Diagnosis™ logo on the dryer.
4. With the phone held in place, press and hold Temp.
Control button for three seconds.
5. Keep the phone in place until the tone transmission
has finished. This takes about 6 seconds and the
display will count down the time.
6. When the recording is complete, vie the diagnosis
by pressing the Next button on the phone.
NOTE
Smart Diagnosis™ is a troubleshooting feature
designed to assist, not replace, the traditional method
of troubleshooting through service calls. The
effectiveness of this feature depends upon various
factors, including, but not limited to, the reception
of the cellular phone being used for transmission,
any external noise that may be present during the
transmission, and the acoustics of the room where the
machine is located.
Accordingly, LG does not guarantee that Smart
Diagnosis™ would accurately troubleshoot any given
issue.
MFL67731050_en_141213.indd 48
NOTE
Do not touch any other buttons or icons on the
display screen.
3. Press and hold the Temp. Control button for three
seconds.
4. Keep the phone in place until the tone transmission
has finished. This takes about 6 seconds and the
display will count down the time.
5. Once the countdo n is over and the tones have
stopped, resume your conversation with the call
center agent, who will then be able to assist you in
using the information transmitted for analysis.
2014.12.13 5:22:37 PM
WARRANTY
49
LG ELECTRONICS CANADA, INC.
LG DRYER LIMITED WARRANTY - Canada
ENGLISH
WARRANTY:
•
•
•
LG CANADA’S SOLE LIABILITY IS LIMITED TO THE WARRANTY SET OUT ABOVE. EXCEPT AS EXPRESSLY PROVIDED ABOVE, LG CANADA
MAKES NO AND HEREBY DISCLAIMS ALL OTHER WARRANTIES AND CONDITIONS RESPECTING THE PRODUCT, WHETHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OR CONDITION OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE, AND NO REPRESENTATIONS SHALL BE BINDING ON LG CANADA. LG CANADA DOES NOT AUTHORIZE ANY
PERSON TO CREATE OR ASSUME FOR IT ANY OTHER WARRANTY OBLIGATION OR LIABILITY IN CONNECTION WITH THE PRODUCT. TO THE
EXTENT THAT ANY WARRANTY OR CONDITION IS IMPLIED BY LAW, IT IS LIMITED TO THE EXPRESS WARRANTY PERIOD ABOVE.
LG CANADA, THE MANUFACTURER OR DISTRIBUTOR SHALL NOT BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, DIRECT OR
INDIRECT DAMAGES, LOSS OF GOODWILL, LOST PROFITS, PUNITIVE OR EXEMPLARY DAMAGES OR ANY OTHER DAMAGE, WHETHER ARISING DIRECTLY OR INDIRECTLY FROM ANY CONTRACTUAL BREACH, FUNDAMENTAL OR OTHERWISE, OR FROM ANY ACTS OR
OMISSIONS, TORT, OR OTHERWISE.
THIS LIMITED WARRANTY DOES NOT COVER:
All costs associated with the above excluded circumstances shall be borne by the consumer.
Write your warranty information below:
For complete warranty details and customer
assistance, please call or visit our website:
Product Registration Information:
Model:
Serial Number:
Date of Purchase:
MFL67731050_en_141213.indd 49
2014.12.13 5:22:37 PM
50
MFL67731050_en_141213.indd 50
2014.12.13 5:22:37 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement