HP | MSR1000 | Command Reference Guide | HP MSR1000 Command Reference Guide

About the HP MSR Router Series
Command References(V7)
Part number: 5998-6352
Software version: CMW710-R0106
Document version: 6PW101-20140807
Legal and notice information
© Copyright 2014 Hewlett-Packard Development Company, L.P.
No part of this documentation may be reproduced or transmitted in any form or by any means without
prior written consent of Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice.
HEWLETT-PACKARD COMPANY MAKES NO WARRANTY OF ANY KIND WITH REGARD TO THIS
MATERIAL, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY
AND FITNESS FOR A PARTICULAR PURPOSE. Hewlett-Packard shall not be liable for errors contained
herein or for incidental or consequential damages in connection with the furnishing, performance, or use
of this material.
The only warranties for HP products and services are set forth in the express warranty statements
accompanying such products and services. Nothing herein should be construed as constituting an
additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
About the HP MSR Router Series Command
References
These command references apply to the following models of the HP MSR routers:
Model
• MSR1002-4
MSR1000
•
•
•
•
•
•
•
MSR2000
MSR3000
MSR2003
MSR2004-24
MSR2004-48
MSR3012
MSR3024
MSR3044
MSR3064
• MSR4060
• MSR4080
MSR4000
The HP MSR router series command references describe the commands and command syntax options
available for the HP MSR Routers.
Command reference
Content
Covers the commands for logging in to and setting up an MSR router. This
command reference includes:
Fundamentals Command
Reference
•
•
•
•
•
•
•
•
•
•
•
CLI
RBAC
Login Management
FTP and TFTP
File System Management
Configuration file management
Software upgrade
Emergency shell
Automatic Configuration
Device Management
Tcl
Covers the interface configuration commands. This command reference
includes:
Interface Command Reference
•
•
•
•
•
•
•
Bulk interface
Ethernet interface
WAN interfaces
POS interface
CPOS interface
ATM interface
Loopback, null, and inloopback interface
Command reference
Content
Covers the commands for configuring Layer 2 technologies and features in
a LAN switched network. This command reference includes:
Layer 2 – LAN Switching
Command Reference
•
•
•
•
•
•
•
•
MAC Address Table
Ethernet link aggregation
Port Isolation
Spanning Tree
Loop detection
VLAN
QinQ
LLDP
Covers WAN access technologies. This command reference includes:
Layer 2 – WAN Access
Command Reference
•
•
•
•
•
•
•
•
PPP
L2TP
HDLC
ISDN
ATM
Modem Management
3G and 4G modem management
DDR
Covers the commands for configuring and managing IP addressing
(including static and dynamic IPv4 and IPv6 address assignment), network
performance optimization, ARP, and interoperation between IPv4 and IPv6.
This command reference includes:
Layer 3 – IP Services Command
Reference
Layer 3 – IP Routing Command
Reference
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
ARP
IP Addressing
DHCP
DNS
NAT
IP Forwarding Basics
Fast Forwarding
Flow classification
Adjacency table
IRDP
IP Performance Optimization
UDP Helper
IPv6 Basics
DHCPv6
IPv6 Fast Forwarding
Tunneling
GRE
ADVPN
Covers the commands for configuring routes for IPv4 and IPv6 networks of
different sizes, route filtering, route control, and policy based routing. This
command reference includes:
• IP Routing Basics
• Static Routing
Command reference
Content
• RIP
• OSPF
• IS-IS
• BGP
• Policy-Based Routing
• IPv6 Static Routing
• RIPng
• OSPFv3
• IPv6 IS-IS
• IPv6 Policy-Based Routing
• Routing policy
• MTR
Covers the commands for Layer 3 IPv4 multicast protocols (IGMP and PIM),
and Layer 3 IPv6 multicast protocols (MLD and IPv6 PIM), Layer 2 IPv4
multicast protocols (IGMP snooping). This command reference includes:
IP Multicast Command
Reference
•
•
•
•
•
•
•
•
•
•
IGMP Snooping
Multicast Routing and Forwarding
IGMP
PIM
MSDP
Multicast VPN
MLD snooping
IPv6 Multicast Routing and Forwarding
MLD
IPv6 PIM
Covers the commands for MPLS and MPLS VPN. This command reference
includes:
MPLS Command Reference
ACL and QoS Command
Reference
•
•
•
•
•
•
•
•
•
•
•
Basic MPLS
Static LSP
LDP
MPLS TE
Static CRLSP
RSVP
Tunnel policy
MPLS L3VPN
MPLS L2VPN
MPLS OAM
MPLS protection switching
Covers the commands for classifying traffic with ACLs, and allocating
network resources and managing congestions with QoS technologies to
improve network performance and network use efficiency. This command
reference includes:
•
•
•
•
ACL
MPLS QoS
QoS
Time range
Covers security feature commands. Available security features include
identity authentication (AAA), access security (802.1X, MAC
authentication, and portal), secure management (SSH). This command
reference includes:
Security Command Reference
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
AAA
802.1X
MAC Authentication
Porta
Port security
Password control
Public key management
PKI
IPsec(IPsec, IKE)
SSH
SSL
ASPF
APR
Session management
Connection limit
Object group
ARP Attack Protection
IP source guard
ARP attack protection
uRPF
Crypto engine
FIPS
Attack detection and prevention
Covers Voice features commands. This command reference includes:
Voice Command Reference
•
•
•
•
•
•
Voice interface
Voice Entity
Dial Program
SIP
Call Services
Fax over IP
Covers high availability commands for managing failure detection. Failure
detection technologies focus on fault detection and isolation. This command
reference includes:
High Availability Command
Reference
Network Management and
Monitoring Command
Reference
•
•
•
•
•
Interface backup
VRRP
BFD
Track
Process placement
Covers the commands that help you manage and monitor your network, for
example, manage system events, sample packets, assess network
performance, and test network connectivity. This command reference
includes:
• System Maintenance and Debugging
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
NQA
NTP
PoE
SNMP
RMON
NETCONF
CWMP
EAA
Process monitoring and maintenance
Sampler
Mirroring
NetStream
IPv6 NetStream
sFlow
Information Center
Covers OAA commands. This command reference includes:
OAA Commands
Probe Commands
• OAP module
• OAP
Covers Probe commands. This command reference includes:
• Router Probe commands
Download PDF

advertising