HP C4380 User manual

HP C4380 User manual
HP Photosmart C4380 All-in-One series
Basics Guide
Hewlett-Packard Company notices
The information contained in this document is subject to change without notice.
All rights reserved. Reproduction, adaptation, or translation of this material is prohibited without prior written permission of Hewlett-Packard, except
as allowed under copyright laws. The only warranties for HP products and services are set forth in the express warranty statements accompanying
such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial
errors or omissions contained herein.
© 2007 Hewlett-Packard Development Company, L.P.
Windows, Windows 2000, and Windows XP are U.S. registered trademarks of Microsoft Corporation.
Windows Vista is either a registered trademark or trademark of Microsoft Corporation in the United States and/or other countries.
Intel and Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries.
1
HP All-in-One overview
The HP All-in-One at a glance....................................................................................................2
Control panel buttons.................................................................................................................3
Find more information.................................................................................................................4
2
Network setup
Integrated wireless WLAN 802.11 network setup.......................................................................5
Wireless ad hoc network setup...................................................................................................7
Connect to additional computers on a network........................................................................10
Change the HP All-in-One from a USB connection to a network connection...........................10
Manage your network settings..................................................................................................11
3
Use the HP All-in-One features
Load originals and load paper..................................................................................................13
Avoid paper jams......................................................................................................................15
Print 10 x 15 cm (4 x 6 inch) photos.........................................................................................16
Scan an image or document.....................................................................................................17
Make a copy.............................................................................................................................17
Replace the print cartridges......................................................................................................18
Clean the HP All-in-One...........................................................................................................20
4
Troubleshooting and support
Uninstall and reinstall the software...........................................................................................22
Hardware setup troubleshooting...............................................................................................22
Wireless setup troubleshooting................................................................................................25
Clear paper jams......................................................................................................................27
Print cartridge troubleshooting..................................................................................................28
Support process.......................................................................................................................29
5
Technical information
System requirements................................................................................................................30
Product specifications...............................................................................................................30
Print cartridge yield...................................................................................................................30
Regulatory notices....................................................................................................................30
Warranty...................................................................................................................................32
1
Contents
Contents
1
HP All-in-One overview
Use the HP All-in-One to quickly and easily accomplish tasks such as making a copy,
scanning documents, or printing photos from a memory card. You can access many
HP All-in-One functions directly from the control panel, without turning on your computer.
NOTE: This guide introduces basic operations and troubleshooting, as well as
provides information for contacting HP support and ordering supplies.
The onscreen Help details the full range of features and functions, including use of
the HP Photosmart software that came with the HP All-in-One.
The HP All-in-One at a glance
HP All-in-One overview
2
Label
Description
1
Control panel
2
On button
3
Memory card slots
4
Wireless network indicator light and button
5
Input tray
6
Tray extender
7
Paper-width guide
8
Print cartridge door
9
Glass
10
Lid backing
11
Rear door
HP All-in-One overview
(continued)
*
Label
Description
12
Rear USB port
13
Power connection*
Use only with the power adapter supplied by HP.
HP All-in-One overview
Control panel buttons
Label
Icon
Name and Description
1
On button: Turns the HP All-in-One on or off. When the HP Allin-One is off, a minimal amount of power is still used by the
device. To completely remove power, turn the HP All-in-One
off, and then unplug the power cord.
2
Quality button: Changes the copy quality or the quality of
photos you print from a memory card. The default quality for
both plain and photo papers is two stars. However, the quality
produced varies depending on the paper type. For plain paper,
two stars represents normal quality. For photo paper, two stars
represents best quality.
3
Size button: Changes the image size to 100% (Actual Size),
fits it to the page (Resize to Fit), or prints borderless images
(Borderless). The default setting is 100% for plain paper and
borderless for photo paper.
4
Copies button: Specifies the desired number of copies.
Control panel buttons
3
Chapter 1
(continued)
Label
Icon
Name and Description
5
Cancel button: Stops a task (such as scanning or copying) or
resets settings (such as Quality and Copies).
6
Scan button: Starts a scan. When a memory card is inserted,
this button advances to the next photo on the memory card
when pressed.
7
Start Copy Black button: Starts a black-and-white copy. In
certain situations (for example, after clearing a paper jam), this
button resumes printing. When a memory card is inserted, this
button acts as a previous image button.
8
Start Copy Color button: Starts a color copy. In certain
situations (for example, after clearing a paper jam), this button
resumes printing. When a memory card is inserted, this button
starts printing the image currently on the display.
HP All-in-One overview
Find more information
A variety of resources, both printed and onscreen, provide information about setting up
and using the HP All-in-One.
•
•
•
4
Setup Guide
The Setup Guide provides instructions for setting up the HP All-in-One and installing
software. Make sure you follow the steps in the Setup Guide in order.
If you have problems during setup, see Troubleshooting in the last section of the
Setup Guide, or see “Troubleshooting and support” on page 22 in this guide.
Onscreen Help
The onscreen Help provides detailed instructions on features of the HP All-in-One
that are not described in this User Guide, including features that are only available
using the software you installed with the HP All-in-One.
www.hp.com/support
If you have Internet access, you can get help and support from the HP Web site. This
Web site offers technical support, drivers, supplies, and ordering information.
HP All-in-One overview
2
Network setup
This section describes how to connect the HP All-in-One to a network and how to view
and manage network settings.
For optimal performance and security in your wireless network, HP recommends you use
a wireless router or access point (802.11) to connect the HP All-in-One and the other
network elements. When network elements are connected through a wireless router or
access point, this is called an infrastructure network.
If you connect the HP All-in-One directly to a wireless-capable computer, without using
a wireless router or access point, this is known as an ad hoc network. You might only be
able to connect to one wireless device at a time with an ad hoc connection.
The advantages of a wireless infrastructure network as compared to an ad hoc network
include:
Advanced network security
Enhanced reliability
Network flexibility
Better performance, especially with 802.11 g mode
If you want to:
See this section:
Connect to a wireless network with a wireless
router (infrastructure).
“Integrated wireless WLAN 802.11 network
setup” on page 5
Connect directly to a wireless-capable
computer without a wireless router (ad-hoc).
“Wireless ad hoc network setup” on page 7
Add connections to more computers on the
network.
“Connect to additional computers on a
network” on page 10
Change the HP All-in-One from a USB
connection to a network connection.
“Change the HP All-in-One from a USB
connection to a network connection”
on page 10
NOTE: Use the instructions in this section if
you first installed the HP All-in-One with a USB
connection, and you now want to change to a
wireless network connection.
Find troubleshooting information.
Network setup
•
•
•
•
“Wireless setup troubleshooting” on page 25
Integrated wireless WLAN 802.11 network setup
Use this section if you want to connect the HP All-in-One to a computer on a wireless
network using a wireless router or access point (802.11). HP recommends this method.
Network setup
5
Chapter 2
To set up the HP All-in-One on an integrated
wireless WLAN 802.11 network, you need to
do the following:
See this section:
First, collect all of the required materials.
“What you need for an integrated wireless
WLAN 802.11 network” on page 6
Next, install the software and connect the
HP All-in-One to the wireless router.
“Connect to an integrated wireless WLAN
802.11 network” on page 6
What you need for an integrated wireless WLAN 802.11 network
To connect the HP All-in-One to an integrated wireless WLAN 802.11 network, you will
need the following:
Network setup
❑ A wireless 802.11 network that includes a wireless router or access point.
❑ A desktop computer or laptop with either wireless networking support, or a network
interface card (NIC). The computer must be connected to the wireless network that
you intend to install the HP All-in-One on.
❑ If you connect the HP All-in-One on a wireless network that has Internet access, HP
recommends that you use a wireless router (access point or base station) that uses
Dynamic Host Configuration Protocol (DHCP).
❑ Network name (SSID).
❑ WEP key or WPA Passphrase (if needed).
Connect to an integrated wireless WLAN 802.11 network
The HP Photosmart Software CD and included USB setup cable provide an easy way to
connect the HP All-in-One to your wireless network.
6
Network setup
CAUTION: To prevent other users from accessing your wireless network, HP
strongly recommends using a password or passphrase (WPA or WEP security) and
a unique network name (SSID) for your wireless router. Your wireless router might
have been shipped with a default network name, which is typically the manufacturer
name. If you use the default network name, your network can be easily accessed by
other users using the same default network name (SSID). It also means that the
HP All-in-One might accidently connect to a different wireless network in your area
which uses the same network name. If this happens you will not be able to access
the HP All-in-One. For more information on how to change the network name, see
the documentation that came with your wireless router.
NOTE: HP provides an online tool that might be able to find your wireless security
settings automatically. Go to: www.hp.com/go/networksetup.
To connect the HP All-in-One
1. Insert the HP Photosmart Software CD in the computer CD-ROM drive.
2. Follow the instructions on the screen.
When you are prompted, connect the HP All-in-One to the computer using the USB
setup cable included in the box. The HP All-in-One will attempt to connect to the
network. If the connection fails, follow the prompts to correct the problem, and then
try again.
3. When the setup is finished, you will be prompted to disconnect the USB cable and
test the wireless network connection. Once the HP All-in-One connects successfully
to the network, install the software on each computer that will use the device over the
network.
Wireless ad hoc network setup
Network setup
Use this section if you want to connect the HP All-in-One directly to a wireless-capable
computer without using a wireless router or access point.
In order to connect the HP All-in-One to your computer (ad hoc), you need to create an
ad hoc network profile on your computer. This includes choosing a network name (SSID)
and WEP security (optional but recommended) for your ad hoc network.
Wireless ad hoc network setup
7
Chapter 2
To set up the HP All-in-One on a wireless ad
hoc network, you need to do the following:
See this section:
First, collect all of the required materials.
“What you need for an ad hoc network”
on page 8
Next, prepare your computer by creating a
network profile.
“Create a network profile for a Windows XP
computer” on page 8
“Create a network profile for other operating
systems” on page 9
Finally, install the software.
“Connect to a wireless ad hoc network”
on page 9
What you need for an ad hoc network
To connect the HP All-in-One to a Windows computer with an ad hoc connection, the
computer must have a wireless network adapter and an ad hoc profile.
Create a network profile for a Windows XP computer
Prepare your computer for an ad hoc connection by creating a network profile.
To create a network profile
NOTE: The HP All-in-One comes configured with a network profile with hpsetup as
the network name (SSID). However, for security and privacy HP recommends you
create a new network profile on your computer as described here.
Network setup
1. In the Control Panel, double-click Network Connections.
2. On the Network Connections window, right-click the Wireless Network
Connection. If you see Enable on the pop-up menu, select it. Otherwise, if you see
Disable on the menu, the wireless connection is already enabled.
3. Right-click the Wireless Network Connection icon, and then click Properties.
4. Click the Wireless Networks tab.
5. Select the Use Windows to configure my wireless network settings check box.
6. Click Add, and then do the following:
a. In Network name (SSID) box, type in a unique network name of your choice.
NOTE: The network name is case sensitive, so it is important to remember
any uppercase (capital) and lowercase (small) letters.
b. If there is a Network Authentication list, select Open. Otherwise, go to the next
step.
c. In the Data encryption list, select WEP.
NOTE: It is possible to create a network that does not use a WEP key.
However, HP recommends using a WEP key in order to secure your network.
d. Make sure that the check box is not selected next to The key is provided for me
automatically. If it is selected, click the check box to clear it.
8
Network setup
e. In the Network key box, type a WEP key that has exactly 5 or exactly 13
alphanumeric (ASCII) characters. For example, if you enter 5 characters, you
might enter ABCDE or 12345. Or, if you enter 13 characters, you might enter
ABCDEF1234567. (12345 and ABCDE are examples only. Select a combination
of your choosing.)
Alternatively, you can use HEX (hexadecimal) characters for the WEP key. A HEX
WEP key must be 10 characters for 40 bit encryption, or 26 characters for 128 bit
encryption.
f. In the Confirm network key box, type the same WEP key you typed in the
previous step.
g. Write down the WEP key exactly as you typed it, including uppercase and
lowercase letters.
NOTE: You must remember the exact uppercase (capital) and lowercase
(small) letters. If you enter your WEP key incorrectly on the HP All-in-One, the
wireless connection will fail.
h. Select the check box for This is a computer-to-computer (ad hoc) network;
wireless access points are not used.
i. Click OK to close the Wireless network properties window, and then click OK
again.
j. Click OK again to close the Wireless Network Properties Connection window.
Create a network profile for other operating systems
If you have an operating system other than Windows XP, HP recommends that you use
the configuration program that came with your wireless LAN card. To find the
configuration program for your wireless LAN card, access your computer's list of
programs.
Using the LAN card configuration program, create a network profile that has the following
values:
•
Network name (SSID): Mynetwork (example only)
•
•
Network setup
NOTE: You should create a network name that is unique and easy for you to
remember. Just remember that the network name is case-sensitive. Therefore,
you must remember which letters are uppercase and lowercase.
Communication mode: Ad Hoc
Encryption: enabled
Connect to a wireless ad hoc network
The HP Photosmart Software CD and included USB setup cable provide an easy way to
connect the HP All-in-One directly to your computer for an ad-hoc wireless network.
Wireless ad hoc network setup
9
Chapter 2
To connect the HP All-in-One
1. Insert the HP Photosmart Software CD in the computer CD-ROM drive.
2. Follow the instructions on the screen.
When you are prompted, connect the HP All-in-One to the computer using the USB
setup cable included in the box. The HP All-in-One will attempt to connect to the
network. If the connection fails, follow the prompts to correct the problem, and then
try again.
3. When the setup is finished, you will be prompted to disconnect the USB cable and
test the wireless network connection. Once the HP All-in-One connects successfully
to the network, install the software on each computer that will use the device over the
network.
Connect to additional computers on a network
You can share the HP All-in-One on a network so that more computers can use it. If the
HP All-in-One is already connected to a computer on the network, you must install the
HP All-in-One software for each additional computer. During the installation, the software
will discover the HP All-in-One on the network for each of the computers. Once you have
set up the HP All-in-One on the network you will not need to configure it again when you
add additional computers.
Network setup
To install the Windows HP All-in-One software on additional networked computers
1. Quit all applications running on your computer, including any virus detection software.
2. Insert the Windows CD that came with the HP All-in-One into the CD-ROM drive on
your computer and follow the onscreen instructions.
3. If a dialog box about firewalls appears, follow the instructions. If you see firewall popup messages, you must always accept or allow the pop-up messages.
4. On the Connection Type screen, select Through the network, and then click
Next.
The Searching screen appears as the Setup program searches for the HP All-in-One
on the network.
5. On the Printer Found screen, verify that the printer description is correct.
If more than one printer is found on the network, the Printers Found screen appears.
Select the HP All-in-One you want to connect.
6. Follow the prompts to install the software.
When you have finished installing the software, the HP All-in-One is ready for use.
7. If you disabled any virus detection software on your computer, make sure to enable
it again.
8. To test your network connection, go to your computer and print a self-test report to
the HP All-in-One.
Change the HP All-in-One from a USB connection to a
network connection
If you first install the HP All-in-One with a USB connection, you can later change to a
wireless network connection. If you already understand how to connect to a network, you
can use the general directions below.
10
Network setup
To change a USB connection to an integrated wireless WLAN 802.11 connection
1. Unplug the USB connection from the back of the HP All-in-One.
2. Insert the HP All-in-One CD in the computer CD-ROM drive.
3. Follow the onscreen instructions for a wireless network installation.
4. When the installation is complete, open Printers and Faxes (or Printers) in the
Control Panel and delete the printers for the USB installation.
For more detailed instructions on connecting the HP All-in-One to a network, see:
•
•
“Integrated wireless WLAN 802.11 network setup” on page 5
“Wireless ad hoc network setup” on page 7
Manage your network settings
You can manage network settings for the HP All-in-One through the HP All-in-One control
panel.
Change basic network settings from the control panel
The HP All-in-One control panel enables you to perform a variety of network management
tasks. This includes printing the network settings, restoring the network defaults, turning
the wireless radio on and off, and printing a wireless network test.
Print network settings
You can print a network configuration page to see network settings such as the IP
address, communication mode, and network name (SSID).
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Print Network Configuration
Page is highlighted, and then press the button next to OK.
Restore network defaults
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Restore Network Defaults
is highlighted, and then press the button next to OK.
3. Confirm that you want to restore the network defaults.
Turn the wireless radio on and off
The wireless radio is off by default, but when you install the software and connect the
HP All-in-One to the network, the wireless radio is turned on automatically. The blue light
on the front of the HP All-in-One indicates that the wireless radio is on. In order to stay
connected to a wireless network, the radio must stay on. However, if the HP All-in-One
is connected directly to a computer with a USB connection, the radio is not used. In this
case you might want to turn the radio off.
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Turn Radio On or Turn Radio
Off is highlighted, and then press the button next to OK.
Manage your network settings
11
Network setup
You can reset the network settings to what they were when you purchased the HP All-inOne.
Chapter 2
Print the wireless network test
The wireless network test performs a series of diagnostic tests to determine whether
network setup is successful. If an issue is detected, a recommendation on how to correct
the issue will be included on the printed report. You can print the wireless network test at
any time.
1. Press the Wireless button on the front of the HP All-in-One.
2. Press the button next to the icon on the display until Wireless Network Test is
highlighted, and then press the button next to OK.
The Wireless Network Test prints.
Network setup
12
Network setup
3
Use the HP All-in-One features
This chapter includes information about how to use the HP All-in-One for basic
operations. In addition, it provides instructions about how to load paper and replace the
print cartridges.
Load originals and load paper
You can load many different types and sizes of paper in the HP All-in-One, including letter
or A4 paper, photo paper, transparencies, envelopes, and HP CD/DVD tattoo labels. By
default, the HP All-in-One is set to detect the size and type of paper you load in the input
tray automatically and then adjust its settings to generate the highest quality output for
that paper.
If you are using special papers, such as photo paper, transparency films, envelopes, or
labels, or if you experience poor print quality using the Automatic setting, you can
manually set the paper size and type for print and copy jobs.
To load an original on the scanner glass
1. Lift the lid on the HP All-in-One.
2. Load your original print side down on the right front corner of the glass.
Use the HP All-in-One features
TIP: For more help on loading an original, refer to the engraved guides along the
edge of the glass.
3. Close the lid.
To load full-size paper
1. Slide the paper-width guide to its outermost position.
Use the HP All-in-One features
13
Chapter 3
NOTE: If you are using letter, A4, or smaller paper, make sure the tray extender
is open all the way.
2. Tap a stack of paper on a flat surface to align the edges, and then check the paper
for the following:
• Make sure it is free of rips, dust, wrinkles, and curled or bent edges.
• Make sure all the paper in the stack is the same size and type.
3. Insert the stack of paper into the input tray with the short edge forward and the print
side down. Slide the stack of paper forward until it stops.
CAUTION: Make sure that the HP All-in-One is idle and silent when you load
paper into the input tray. If the HP All-in-One is servicing the print cartridges or
otherwise engaged in a task, the paper stop inside the device might not be in
place. You could push the paper too far forward, causing the HP All-in-One to
eject blank pages.
TIP: If you are using letterhead, insert the top of the page first with the print side
down.
Use the HP All-in-One features
4. Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray
and is no higher than the top of the paper-width guide.
NOTE: When you use legal-size paper, leave the tray extender closed.
14
Use the HP All-in-One features
To load 10 x 15 cm (4 x 6 inch) photo paper in the input tray
1. Remove all paper from the input tray.
2. Insert the stack of photo paper into the far-right side of the input tray with the short
edge forward and the print side down. Slide the stack of photo paper forward until it
stops.
If the photo paper you are using has perforated tabs, load the photo paper so that the
tabs are closest to you.
TIP: For more help on loading small-size photo paper, refer to the guides
engraved in the base of the input tray for loading photo paper.
3. Slide the paper-width guide inward until it stops at the edge of the paper.
Do not overload the input tray; make sure the stack of paper fits within the input tray
and is no higher than the top of the paper-width guide.
Avoid paper jams
•
•
•
•
•
•
•
•
Remove printed papers from the output tray frequently.
Prevent curled or wrinkled paper by storing all unused paper flat in a resealable bag.
Ensure that paper loaded in the input tray lays flat and the edges are not bent or torn.
Do not combine different paper types and paper sizes in the input tray; the entire stack
of paper in the input tray must be the same size and type.
Adjust the paper-width guide in the input tray to fit snugly against all paper. Make sure
the paper-width guide does not bend the paper in the input tray.
Do not overload the input tray; make sure the stack of paper fits within the input tray
and is no higher than the top of the paper-width guide.
Do not force paper too far forward in the input tray.
Use paper types that are recommended for the HP All-in-One.
Avoid paper jams
15
Use the HP All-in-One features
To help avoid paper jams, follow these guidelines.
Chapter 3
Print 10 x 15 cm (4 x 6 inch) photos
You can select specific photos on your memory card to print as 10 x 15 cm (4 x 6 inch)
photos.
1
xD-Picture Card
2
Memory Stick, Memory Stick Pro, Memory Stick Select, Memory Stick Magic Gate, Memory
Stick Duo or Duo Pro (adapter optional), or Memory Stick Micro (adapter required)
3
CompactFlash (CF) types I and II
4
Secure Digital (SD), Secure Digital Mini (adapter required), Secure Digital High Capacity
(SDHC), MultiMediaCard (MMC), MMC Plus, MMC Mobile (RS-MMC; adapter required),
TransFlash MicroSD Card, or Secure MultiMedia Card
To print one or more 10 x 15 cm (4 x 6 inch) photos
1. Insert your memory card into the appropriate slot on the HP All-in-One.
The most recent image on the card appears on the display.
Use the HP All-in-One features
2. Load 10 x 15 cm (4 x 6 inch) photo paper in the input tray.
3. Press the buttons next to the and icons on the display to scroll through the photos
on your memory card until the photo you want to print appears.
16
Use the HP All-in-One features
4. Do one of the following:
• For faster printing with slightly reduced resolution, leave the Quality setting at
best resolution (as indicated by the two star icons on the display).
• For much faster printing with moderately reduced resolution, press the Quality
button until one star icon appears on the display (indicating normal resolution).
• For maximum resolution, press the Quality button until three star icons appear
on the display.
5. Leave the default Size setting as Borderless.
6. Press the Copies button until the number of copies you want to print appears on the
display.
7. Press the Print button.
TIP: While the photo is printing, you can continue scrolling through the photos
on your memory card. When you see a photo you want to print, you can press the
Print button to add that photo to the print queue.
Scan an image or document
For original documents or images placed on the glass, you can start a scan from your
computer or from the HP All-in-One. This section explains the second option: how to scan
from the control panel of the HP All-in-One to a computer.
To use the scan features, the HP All-in-One and computer must be connected and turned
on. The HP Photosmart Software must also be installed and running on your computer
prior to scanning. To verify that the HP Photosmart Software is running on a Windows
computer, look for the HP Digital Imaging Monitor icon in the system tray at the lower
right side of the screen, near the time.
To scan to a computer
1. Load your original print side down on the right front corner of the glass.
2. Ensure that there are no memory cards inserted in the memory card slots on the
HP All-in-One.
3. Press Scan.
A preview image of the scan appears on your computer, where you can edit it. Any
edits that you make apply to the current scan session only.
The HP Photosmart Software has many tools that you can use to edit your scanned
image. You can improve the overall image quality by adjusting the brightness,
sharpness, color tone, and saturation. You can also crop, straighten, rotate, or resize
the image.
4. Make any edits to the preview image, and then click Accept when you are finished.
Make a copy
You can make quality copies from the control panel.
Scan an image or document
17
Use the HP All-in-One features
NOTE: Closing the HP Digital Imaging Monitor icon in the Windows system tray
can cause the HP All-in-One to lose some of its scan functionality. If this happens,
you can restore full functionality by restarting your computer or by starting the
HP Photosmart Software.
Chapter 3
To make a copy from the control panel
1. Make sure you have paper loaded in the input tray.
2. Load your original print side down on the right front corner of the glass.
3. Press Start Copy Black or Start Copy Color to begin copying.
Replace the print cartridges
Follow these instructions when you need to replace print cartridges.
NOTE: When the ink level for the print cartridge is low, a message appears on the
display. You can also check the ink levels by using the Printer Toolbox available
through the HP Photosmart Software on your computer or through the Print
Properties dialog box on your computer.
If you do not already have replacement print cartridges for the HP All-in-One, you can
order them by clicking the Shop for HP Supplies icon on your computer. On a Windows
computer this is located in the HP folder in the Start menu.
For more information see www.hp.com/buy/supplies.
To replace the print cartridges
1. Make sure the HP All-in-One is on.
CAUTION: If the HP All-in-One is off when you open the print cartridge door to
access the print cartridges, the HP All-in-One will not release the cartridges for
changing. You might damage the HP All-in-One if the print cartridges are not
docked safely when you try to remove them.
2. Make sure you have letter or A4 unused plain white paper loaded in the input tray.
3. Open the print cartridge door.
The print carriage moves to the far right side of the HP All-in-One.
Use the HP All-in-One features
4. Wait until the print carriage is idle and silent, and then lightly press down on a print
cartridge to release it.
If you are replacing the tri-color print cartridge, remove the print cartridge from the
slot on the left.
If you are replacing the black or photo print cartridge, remove the print cartridge from
the slot on the right.
18
Use the HP All-in-One features
1
Print cartridge slot for the tri-color print cartridge
2
Print cartridge slot for the black and photo print cartridges
5. Pull the print cartridge towards you out of its slot.
6. If you are removing the black print cartridge in order to install the photo print cartridge,
store the black print cartridge in the print cartridge protector or an airtight plastic
container.
7. Remove the new print cartridge from its packaging and, being careful to touch only
the black plastic, gently remove the plastic tape by using the pink pull tab.
1
Copper-colored contacts
2
Plastic tape with pink pull tab (must be removed before installing)
3
Ink nozzles under tape
Use the HP All-in-One features
CAUTION: Do not touch the copper-colored contacts or ink nozzles. Also, do
not re-tape the print cartridges. Doing so can result in clogs, ink failure, and bad
electrical connections.
Replace the print cartridges
19
Chapter 3
8. Hold the print cartridge with the HP logo on top, and insert the new print cartridge into
the empty cartridge slot. Make sure you push the print cartridge in firmly until it snaps
into place.
If you are installing the tri-color print cartridge, slide it into the left slot.
If you are installing a black or photo print cartridge, slide it into the right slot.
9. Close the print cartridge door.
If you installed a new print cartridge, the HP All-in-One prints a print cartridge
alignment page.
10. When prompted, ensure plain white paper is loaded in the input tray, then press the
button next to OK.
NOTE: If you have colored paper loaded in the input tray when you align the print
cartridges, the alignment will fail. Load unused plain white paper into the input
tray, and then try the alignment again.
11. Load the page print side down on the right front corner of the glass, and then press
the button next to OK to scan the page.
When the On button stops flashing, the alignment is complete and the page can be
removed. Recycle or discard the page.
Clean the HP All-in-One
Use the HP All-in-One features
To ensure that your copies and scans remain clear, you might need to clean the glass
and lid backing. You might also want to dust the exterior of the HP All-in-One.
TIP: You can purchase an HP Cleaning Kit for Inkjet Printers and All-in-Ones
(Q6260A) that provides everything needed to safely clean your HP device. For more
information, go to: www.shopping.hp.com/accessories-store/printer.
Clean the glass
Fingerprints, smudges, hair, and dust on the main glass surface slow down performance
and affect the accuracy of the copy and scan features.
20
Use the HP All-in-One features
To clean the glass
1. Turn off the HP All-in-One, unplug the power cord, and raise the lid.
2. Clean the glass with a soft cloth or sponge slightly moistened with a nonabrasive
glass cleaner.
CAUTION: Do not use abrasives, acetone, benzene, or carbon tetrachloride on
the glass, since they can damage it. Do not place or spray liquid directly on the
glass. The liquid might seep under the glass and damage the device.
3. Dry the glass with a dry, soft, lint-free cloth to prevent spotting.
4. Plug in the power cord, and then turn on the HP All-in-One.
Clean the lid backing
Minor debris can accumulate on the white document backing located underneath the lid
of the HP All-in-One.
To clean the lid backing
1. Turn off the HP All-in-One, unplug the power cord, and raise the lid.
2. Clean the white document backing with a soft cloth or sponge slightly moistened with
a mild soap and warm water.
Wash the backing gently to loosen debris. Do not scrub the backing.
3. Dry the backing with a dry, soft, lint-free cloth.
CAUTION: Do not use paper-based wipes, as these might scratch the backing.
4. If further cleaning is needed, repeat the previous steps using isopropyl (rubbing)
alcohol, and wipe the backing thoroughly with a damp cloth to remove any residual
alcohol.
CAUTION: Be careful not to spill alcohol on the glass or exterior of the HP Allin-One, as this might damage the device.
Use the HP All-in-One features
5. Plug in the power cord, and then turn on the HP All-in-One.
Clean the HP All-in-One
21
Troubleshooting and support
4
Troubleshooting and support
This chapter contains troubleshooting information for the HP All-in-One. Specific information is
provided for installation and configuration issues, and some operational topics. For more
troubleshooting information, see the onscreen Help that came with your software.
Many issues are caused when the HP All-in-One is connected to the computer using a USB cable
before the HP All-in-One software is installed on the computer. If you connected the HP All-in-One
to your computer before the software installation screen prompts you to do so, you must follow these
steps:
Troubleshooting common setup issues
1. Disconnect the USB cable from the computer.
2. Uninstall the software (if you have already installed it).
3. Restart your computer.
4. Turn off the HP All-in-One, wait one minute, then restart it.
5. Reinstall the HP All-in-One software.
CAUTION: Do not connect the USB cable to the computer until prompted by the software
installation screen.
For support contact information, see the inside back cover of this guide.
Uninstall and reinstall the software
If your installation is incomplete, or if you connected the USB cable to the computer before prompted
by the software installation screen, you might need to uninstall and then reinstall the software. Do
not simply delete the HP All-in-One application files from your computer. Make sure to remove them
properly using the uninstall utility provided when you installed the software that came with the HP Allin-One.
To uninstall from a Windows computer and then reinstall
1. On the Windows taskbar, click Start, Settings, Control Panel (or just Control Panel).
2. Double-click Add/Remove Programs (or click Uninstall a program).
3. Select HP Photosmart All-In-One Driver Software, and then click Change/Remove.
Follow the onscreen instructions.
4. Disconnect the HP All-in-One from your computer.
5. Restart your computer.
NOTE: It is important that you disconnect the HP All-in-One before restarting your
computer. Do not connect the HP All-in-One to your computer until after you have reinstalled
the software.
6.
7.
Insert the HP All-in-One CD-ROM into your computer’s CD-ROM drive and then start the Setup
program.
Follow the onscreen instructions and the instructions provided in the Setup Guide that came
with the HP All-in-One.
Hardware setup troubleshooting
Use this section to solve any problems you might encounter while setting up the HP All-in-One
hardware.
The HP All-in-One will not turn on
Cause: The HP All-in-One is not properly connected to a power supply.
22
Troubleshooting and support
•
•
•
1
Power connection
2
Power cord and adapter
3
Power outlet
Troubleshooting and support
Solution
•
Make sure the power cord is firmly connected to both the HP All-in-One and the power
adapter. Plug the power cord into a power outlet, surge protector, or power strip.
If you are using a power strip, make sure the power strip is on. Or, try plugging the HP Allin-One directly into a power outlet.
Test the power outlet to make sure it is working. Plug in an appliance that you know works,
and see if the appliance has power. If not, then there might be a problem with the power
outlet.
If you plugged the HP All-in-One into a switched outlet, make sure the switch is on. If it is
switched to on but still does not work, then there might be a problem with the power outlet.
Cause: You pressed the On button too quickly.
Solution: The HP All-in-One might not respond if you press the On button too quickly. Press
the On button once. It might take a few minutes for the HP All-in-One to turn on. If you press
the On button again during this time, you might turn the device off.
CAUTION: If the HP All-in-One still does not turn on, it might have a mechanical failure.
Unplug the HP All-in-One from the power outlet and contact HP. Go to: www.hp.com/
support. If prompted, choose your country/region, and then click Contact HP for information
on calling for technical support.
I connected the USB cable, but I am having problems using the HP All-in-One with
my computer
Cause: The USB cable was connected before the software was installed. Connecting the USB
cable before prompted can cause errors.
Solution: You must first install the software that came with the HP All-in-One before
connecting the USB cable. During installation, do not plug in the USB cable until prompted by
the onscreen instructions.
Once you have installed the software, connecting your computer to the HP All-in-One with a
USB cable is straightforward. Simply plug one end of the USB cable into the back of your
Hardware setup troubleshooting
23
Chapter 4
computer and the other into the back of the HP All-in-One. You can connect to any USB port on
the back of your computer.
Troubleshooting and support
For more information on installing the software and connecting the USB cable, see the Setup
Guide that came with the HP All-in-One.
The HP All-in-One does not print
Solution: If the HP All-in-One and computer are not communicating with each other, try the
following:
•
Look at the On light located on the front of the HP All-in-One. If it is not lit, the HP All-inOne is turned off. Make sure the power cord is firmly connected to the HP All-in-One and
plugged into a power outlet. Press the On button to turn on the HP All-in-One.
•
Make sure the print cartridges are installed.
•
Make sure you have paper loaded in the input tray.
•
Check that the HP All-in-One does not have a paper jam.
•
Check that the print carriage is not jammed.
Open the print cartridge door to access the print carriage area. Remove any objects that
are blocking the print carriage, including any packing materials. Turn the HP All-in-One off
and then turn it on again.
•
Check that the HP All-in-One print queue is not paused (Windows) or stopped (Mac). If it
is, choose the appropriate setting to resume printing. For more information about accessing
the print queue, see the documentation that came with the operating system installed on
your computer.
•
Check the USB cable. If you are using an older cable, it might not be working properly. Try
connecting it to another product to see if the USB cable works. If you experience problems,
the USB cable might need to be replaced. Also verify that the cable does not exceed 3
meters (9.8 feet) in length.
•
Make sure your computer is USB ready. Some operating systems, such as Windows 95
and Windows NT, do not support USB connections. Check the documentation that came
with your operating system for more information.
•
Check the connection from the HP All-in-One to your computer. Verify that the USB cable
is securely plugged into the USB port on the back of the HP All-in-One. Make sure the other
end of the USB cable is plugged into a USB port on your computer. After the cable is
connected properly, turn the HP All-in-One off and then on again.
•
If you are connecting the HP All-in-One through a USB hub, make sure the hub is turned
on. If the hub is on, try connecting directly to your computer.
24
Troubleshooting and support
Check other printers or scanners. You might need to disconnect older products from your
computer.
•
Try connecting the USB cable to another USB port on your computer. After you check the
connections, try restarting your computer. Turn the HP All-in-One off and then on again.
•
If the HP All-in-One is offline, turn the HP All-in-One off and on again. Start a print job.
•
If necessary, remove and then install the software you installed with the HP All-in-One again.
For more information on setting up the HP All-in-One and connecting it to your computer, see
the Setup Guide that came with the HP All-in-One.
Wireless setup troubleshooting
This section addresses problems you might encounter setting up a network.
During wireless network setup you do not see the SSID (network name)
displayed
Cause: Your wireless router is not broadcasting its network name (SSID) because the
Broadcast SSID option is turned off.
Solution: Access the router's Embedded Web Server and turn on the Broadcast SSID option.
See the user guide that came with your wireless router for information on how to access the
Embedded Web Server and check the Broadcast SSID setting.
For more information, see:
“Connect to an integrated wireless WLAN 802.11 network” on page 6
Cause: The wireless router (infrastructure) or computer (ad hoc) is too far from the HP All-inOne or there is interference.
Solution: In order to establish a good signal between the HP All-in-One and wireless router
(infrastructure) or computer (ad hoc), you might have to experiment a bit. Assuming the
equipment is functioning properly, try doing the following things separately or in combination:
•
If there is a long distance between your computer or wireless router and the HP All-in-One,
move them closer together.
•
If there are metal objects (such as a metal bookcase or refrigerator) in the transmission
path, clear the path between the HP All-in-One and the computer or wireless router.
•
If a cordless telephone, microwave, or other device that emits radio signals transmitting at
2.4 GHz is nearby, move it farther away to reduce radio interference.
•
If your computer or wireless router is near an external wall, move them away from the wall.
Cause: Your network name (SSID) may be at the bottom of the SSID list that is displayed
when you install the HP All-in-One on a wireless network.
Solution: Press
to scroll to the bottom of the list. Infrastructure entries are listed first, ad
hoc last.
Weak signal
Cause: The HP All-in-One is too far away from the wireless router or there is interference.
Solution: In order to establish a good signal between the HP All-in-One and the wireless
router, you might have to experiment a bit. Assuming the equipment is functioning properly, try
doing the following things separately or in combination:
•
If there is a long distance between your computer or wireless router and the HP All-in-One,
move them closer together.
•
If there are metal objects (such as a metal bookcase or refrigerator) in the transmission
path, clear the path between the HP All-in-One and the computer or wireless router.
Wireless setup troubleshooting
25
Troubleshooting and support
•
Chapter 4
•
Troubleshooting and support
•
If a cordless telephone, microwave, or other device that emits radio signals transmitting at
2.4 GHz is nearby, move it farther away to reduce radio interference.
If your computer or wireless router is near an external wall, move them away from the wall.
Cannot connect to network during setup
Cause: The equipment is not turned on.
Solution: Turn on the networked devices, such as the wireless router for an infrastructure
network, or the computer for an ad hoc network. For more information on how to turn on the
wireless router, see the documentation that came with your wireless router.
Cause: The HP All-in-One is not receiving a signal.
Solution: Move the wireless router and the HP All-in-One closer together. Then run the
wireless setup process again.
For more information, see:
“Integrated wireless WLAN 802.11 network setup” on page 5
Cause: If you manually entered your network name (SSID), you might have entered it
incorrectly.
Solution: Run the wireless setup process again and enter your network name (SSID)
carefully. Remember that the SSID is case-sensitive.
For more information, see:
“Connect to an integrated wireless WLAN 802.11 network” on page 6
Cause: The setting for MAC address filtering might be enabled on your wireless router.
Solution: Disable MAC address filtering on your wireless router until the HP All-in-One has
successfully connected to your network. If you re-enable MAC address filtering on your wireless
router, make sure the MAC address of the HP All-in-One is on the list of acceptable MAC
addresses.
Invalid WEP key during wireless setup
Cause: If you are using WEP security, you might have entered the WEP key incorrectly during
the wireless setup process.
Solution: During the wireless setup process, you might have entered the WEP key incorrectly.
Some wireless routers provide up to four WEP keys. The HP All-in-One uses the first WEP key
(selected by the wireless router as the default WEP key). Run the wireless setup process again
and be sure to use the first WEP key provided by the wireless router. Enter the WEP key exactly
as it appears in the wireless router settings. The WEP key is case sensitive.
If you do not know the WEP key, see the documentation that came with your wireless router for
information on how to access the router's Embedded Web Server. You can find the WEP key
by logging onto the router's Embedded Web Server using a computer on the wireless network.
Invalid passphrase during wireless setup
Cause: During the wireless setup process, you might have entered the WPA passphrase
incorrectly.
Solution: Run the wireless setup process again and enter the correct passphrase. The
passphrase is case-sensitive.
The Printer Not Found screen appears during installation
Cause: An anti-virus or anti-spyware application is preventing the HP All-in-One from
accessing your computer.
26
Troubleshooting and support
Cause: A Virtual Private Network (VPN) is preventing the HP All-in-One from accessing your
computer.
Solution: Temporarily disable the VPN before proceeding with the installation.
NOTE: The HP All-in-One functionality will be limited during VPN sessions.
Cause: The HP All-in-One is not turned on.
Solution: Turn on the HP All-in-One.
Clear paper jams
If the HP All-in-One has a paper jam, first check the rear door.
If the jammed paper is not in the rear rollers, check the front door.
To clear a paper jam from the rear door
1. Press in the tab on the left side of the rear door to release the door. Remove the door by pulling
it away from the HP All-in-One.
2.
Gently pull the paper out of the rollers.
CAUTION: If the paper tears when you are removing it from the rollers, check the rollers
and wheels for torn pieces of paper that might be remaining inside the device. If you do not
remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.
3.
4.
Replace the rear door. Gently push the door forward until it snaps into place.
Press Start Copy Black or Start Copy Color to continue the current job.
To clear a paper jam from the front door
1. If necessary, pull the input tray down to open it. Then, lower the print cartridge door.
Clear paper jams
27
Troubleshooting and support
Solution: Uninstall the HP All-in-One software, and then reboot your computer. Temporarily
disable anti-virus or anti-spyware applications, and then reinstall the HP All-in-One software.
You can re-enable your anti-virus or anti-spyware applications after installation is complete. If
you see firewall pop-up messages, you must always accept or allow the pop-up messages.
If the screen still appears, try uninstalling the HP All-in-One software, rebooting your computer,
and temporarily disabling your firewall before reinstalling the HP All-in-One software. You can
re-enable your firewall application after installation is complete. If you still see firewall pop-up
messages, you must always accept or allow the pop-up messages.
For more information, see the documentation provided with the firewall software.
Chapter 4
Troubleshooting and support
2.
Gently pull the paper out of the rollers.
CAUTION: If the paper tears when you are removing it from the rollers, check the rollers
and wheels for torn pieces of paper that might be remaining inside the device. If you do not
remove all the pieces of paper from the HP All-in-One, more paper jams are likely to occur.
3.
Close the print cartridge door.
4.
Press Start Copy Black to continue the current job.
Print cartridge troubleshooting
If you are experiencing problems with printing, you might have a problem with one of the print
cartridges. For more information, see “Replace the print cartridges” on page 18 in this guide.
•
Keep all print cartridges in the original sealed packages until they are needed.
•
Store print cartridges at room temperature (15.6°-26.6° C or 60°-78° F).
•
Do not reattach the protective tape once it has been removed from the print cartridge.
Reattaching the plastic tape might damage the print cartridge. Place the print cartridge in the
HP All-in-One immediately after removing the plastic tape. If this is not possible, store it in a print
cartridge protector or airtight plastic container.
•
HP recommends that you do not remove the print cartridges from the HP All-in-One until you
have replacement print cartridges available to install.
•
Turn off the HP All-in-One from the control panel. Do not turn off the device by turning off a
power strip or unplugging the power cord from the HP All-in-One. If you improperly turn off the
HP All-in-One, the print carriage does not return to the correct position and the print cartridges
can dry out.
•
Do not open the print cartridge door unless necessary. This exposes the print cartridges to air,
which reduces the life of the print cartridges.
NOTE: If you leave the print cartridge door open for a long period of time, the HP All-inOne will recap the print cartridges to protect them from exposure to air.
•
Clean the print cartridges when you notice a significant decrease in print quality.
TIP: You might notice a decrease in print quality if the print cartridges have not been used
for a long time.
28
Troubleshooting and support
•
Do not clean the print cartridges unnecessarily. This wastes ink and shortens the life of the
cartridges.
Handle print cartridges carefully. Dropping, jarring, or rough handling during installation can
cause temporary printing problems. If print quality is poor right after cartridge installation, allow
half an hour for the print cartridge to recover.
Support process
If you have a problem, follow these steps:
1. Check the documentation that came with the HP All-in-One.
2. Visit the HP online support Web site at www.hp.com/support. HP online support is available to
all HP customers. It is the fastest source for up-to-date device information and expert assistance
and includes the following features:
•
Fast access to qualified online support specialists
•
Software and driver updates for the HP All-in-One
•
Valuable HP All-in-One and troubleshooting information for common problems
•
Proactive device updates, support alerts, and HP newsgrams that are available when you
register the HP All-in-One
3. Call HP support. Support options and availability vary by device, country/region, and language.
For a list of support phone numbers, see the printed documentation that came with the device.
Support process
29
Troubleshooting and support
•
5
Technical information
The technical specifications and international regulatory information for the HP All-in-One are
provided in this section.
System requirements
Software system requirements are located in the Readme file.
Product specifications
For product specifications, go to the HP Web site at www.hp.com/support.
Paper specifications
•
Input tray capacity: Plain paper sheets: Up to 100 (20 lb./75 gsm. paper)
•
Output tray capacity: Plain paper sheets: Up to 50 (20 lb./75 gsm. paper)
NOTE: For a complete list of supported media sizes, see the printer software.
Technical information
Physical specifications
•
Height: 16.97 cm (7.0 inches)
•
Width: 44 cm (16.8 inches)
•
Depth: 25.9 cm (10.2 inches)
•
Weight: 4.5 kg (10 pounds)
Power specifications
•
Power consumption: 25 watts maximum (average printing)
•
Input voltage (0957-2231): AC 100 to 240 V ~ 600 mA 50–60 Hz
•
Input voltage (0957-2248): AC 200 to 240 V ~ 400 mA 50-60 Hz
•
Output voltage: DC 32 V===375 mA, 16 V===500 mA
NOTE: Use only with the power adapter supplied by HP.
Environmental specifications
•
Recommended operating temperature range: 15º to 32º C (59º to 90º F)
•
Allowable operating temperature range: 5º to 35º C (41º to 95º F)
•
Humidity: 15% to 80% RH non-condensing
•
Non-operating (Storage) temperature range: –20º to 50º C (–4º to 122º F)
•
In the presence of high electromagnetic fields, it is possible the output from the HP All-in-One
may be slightly distorted
•
HP recommends using a USB cable less than or equal to 3 m (10 feet) in length to minimize
injected noise due to potential high electromagnetic fields
Print cartridge yield
Ink from the cartridges is used in the printing process in a number of different ways, including in the
initialization process, which prepares the device and cartridges for printing, and in printhead
servicing, which keeps print nozzles clear and ink flowing smoothly. In addition, some residual ink
is left in the cartridge after it is used. For more information, see www.hp.com/go/inkusage.
Visit www.hp.com/pageyield for more information on estimated cartridge yields.
Regulatory notices
The HP All-in-One meets product requirements from regulatory agencies in your country/region. For
a complete listing of regulatory notices, see the onscreen Help.
30
Technical information
Technical information
Regulatory model identification number
For regulatory identification purposes, your product is assigned a Regulatory Model Number. The
Regulatory Model Number for your product is SNPRB-0721-01. This regulatory number should not
be confused with the marketing name (HP Photosmart C4380 All-in-One series, etc.) or product
numbers (CC280A, etc.).
Regulatory notices
31
Chapter 5
Warranty
Technical information
32
Technical information
www.hp.com/support
ᦎᥫҫᦐᦀᦿҫ
Ӆҳҵ᧗ҫ
$UJHQWLQD%XHQRV$LUHV
뼑霢
$UJHQWLQD
/X[HPERXUJ)UDQ©DLV
$XVWUDOLD
/X[HPERXUJ'HXWVFK
$XVWUDOLDRXWRIZDUUDQW\
0DOD\VLD
˜VWHUUHLFK
0DXULWLXV
0«[LFR&LXGDGGH0«[LFR
0«[LFR
ᧆ᧓ᦎᦄᥲᦿҫ
%HOJL­
%HOJLTXH
%UDVLO6DR3DXOR
1HGHUODQG
%UDVLO
1HZ=HDODQG
&DQDGD
KS
LQYHQW
1LJHULD
1RUJH
&HQWUDO$PHULFD7KH&DULEEHDQ ZZZKSFRPVXSSRUW
&KLOH
Ё೑
Ё೑
&RORPELD%RJRW£
&RORPELD
Ҭᦎᦰᧄᦿҫ
Ӆ᥮ᧄᦫӎ
3DQDP£
3DUDJXD\
3HU¼
3KLOLSSLQHV
3ROVND
&RVWD5LFD
3RUWXJDO
ÎHVN£UHSXEOLND
3XHUWR5LFR
'DQPDUN
5HS¼EOLFD'RPLQLFDQD
(FXDGRU$QGLQDWHO
5HXQLRQ
(FXDGRU3DFLILWHO
5RP¤QLD
̷͕͘͘͏̳͕͉͇ͦ͑͘
℡
℡
ᦎᦜᧃ
̷͕͘͘͏̸̶͇͔͙͙͈͚ͦ͑͌͌͗͗͊
(O6DOYDGRU
(VSD³D
)UDQFH
'HXWVFKODQG
˃˨˨˙ˡ˞˞˭˹˱ˬˢ˫˶˱ˢˮ˦˧˹
$OORWKHU$IULFDQ(QJOLVK6SHDNLQJ ,6(FRXQWULHV
˃˨˨˙ˡ˞ˢ˪˱˹˯˃˨˨˙ˡ˞˯
6RXWK$IULFD56$
˃˨˨˙ˡ˞˞˭˹̱˺˭ˮˬ
5HVWRI:HVW$IULFD
*XDWHPDOD
6XRPL
佭␃⡍߹㸠ᬓऔ
6YHULJH
0DJ\DURUV]£J
6ZLW]HUODQG
,QGLD
㟎☷
,QGLD
ࡷࡎ࡙
,QGRQHVLD
ᥴ᧔ᥱ᧎᦬ᦔᦿҫ
6LQJDSRUH
6ORYHQVNR
ᦒᧇ᧎᥷
Ӂҫᦎ᦬ᦿҫ
7ULQLGDG7REDJR
᥶᧓᧎ᦼᦿҫ
7¾UNL\H
Ӆ᥮ᧈᥲᦿ
̺͇͔͇͑͗ͭ
ᦎᦤᦷ
ᧆᧄ᧔ᦿҫ
,UHODQG
Ҏ҂Ққҋ
Үҫҵ᥮ᧃ᧙ҫᥴ᧔ᥱᦎ᦬ᦿҫҭᦊᦄ᥸ᧄᦿҫ
8QLWHG.LQJGRP
8QLWHG6WDWHV
8UXJXD\
,WDOLD
9HQH]XHOD&DUDFDV
-DPDLFD
9HQH]XHOD
㡴㦻
9L¬W1DP
㡴㦻㛉ゾ榊崀ቑ⫃⚗
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement