HP R1500 User manual
HP R1500 G3 UPS
User Guide
Abstract
This document includes installation, configuration, and operation information for the HP R1500 G3 UPS. This document is for the person who installs
and maintains power products. HP assumes you are qualified in the servicing of high-voltage equipment and trained in recognizing hazards in
products with hazardous energy levels.
Part Number: 651175-002
August 2012
Edition: 2
© Copyright 2011, 2012 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express
warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall
not be liable for technical or editorial errors or omissions contained herein.
Microsoft®, Windows®, Windows Server®, and Windows Vista® are U.S. registered trademarks of Microsoft Corporation. Bluetooth® is a
trademark owned by its proprietor and used by Hewlett-Packard Company under license.
Contents
Component identification ............................................................................................................... 6
UPS
UPS
UPS
UPS
UPS
UPS
R1500 G3 overview ........................................................................................................................... 6
front panel ......................................................................................................................................... 6
front panel controls ............................................................................................................................. 7
front panel LED indicators .................................................................................................................... 7
R1500 G3 NA/JPN/TWN rear panel .................................................................................................. 8
R1500 G3 INTL rear panel .................................................................................................................. 9
Installation ................................................................................................................................. 10
Precautions ............................................................................................................................................. 10
Preparing to install the hardware ............................................................................................................... 10
Tools required ............................................................................................................................... 10
Selecting a site .............................................................................................................................. 10
Readying the equipment ................................................................................................................. 11
Installing the UPS .................................................................................................................................... 11
Connecting the batteries ................................................................................................................. 12
Attaching the UPS front bezel .......................................................................................................... 13
Selecting the UPS voltage configuration ............................................................................................ 14
Connecting the host computer ......................................................................................................... 14
Connecting the Network Transient Protectors ..................................................................................... 15
Connecting the UPS to utility power ................................................................................................. 16
Connecting devices to the UPS ........................................................................................................ 16
Charging the UPS batteries ............................................................................................................. 17
Powering up the UPS ..................................................................................................................... 17
Installing the optional UPS Network Module ............................................................................................... 17
Connecting the UPS Network Module .............................................................................................. 19
UPS operations ........................................................................................................................... 20
Modes of operation ................................................................................................................................. 20
Operate mode .............................................................................................................................. 20
Battery mode ................................................................................................................................ 20
Initiating a self-test ................................................................................................................................... 20
Silencing an audible alarm ....................................................................................................................... 20
Powering down the UPS ........................................................................................................................... 21
Maintenance .............................................................................................................................. 22
Removing the UPS front bezel ................................................................................................................... 22
Replacing the batteries ............................................................................................................................. 22
Important battery safety information ................................................................................................. 22
Battery care and storage guidelines ................................................................................................. 23
UPS battery replacement procedure ................................................................................................. 23
Testing the new battery module ....................................................................................................... 25
Replacing the UPS ................................................................................................................................... 25
Replacing the UPS option card .................................................................................................................. 25
Updating the UPS firmware ...................................................................................................................... 26
Configuring a USB to serial converter............................................................................................... 26
Reassigning the USB COM ports ..................................................................................................... 27
Contents
3
Power management .................................................................................................................... 29
Power Protector software .......................................................................................................................... 29
Troubleshooting .......................................................................................................................... 31
LED and audible alarm troubleshooting ...................................................................................................... 31
UPS does not start ................................................................................................................................... 32
UPS operates on battery only .................................................................................................................... 32
UPS frequently switches between utility and battery power ............................................................................ 32
UPS does not provide the expected backup time ......................................................................................... 32
UPS cannot communicate with the host computer ......................................................................................... 33
UPS emits a slight clicking noise ................................................................................................................ 33
Site wiring condition ................................................................................................................................ 33
Specifications ............................................................................................................................. 34
UPS physical specifications ....................................................................................................................... 34
UPS input specifications ........................................................................................................................... 34
UPS output specifications .......................................................................................................................... 34
Power protection specifications ....................................................................................................... 34
Voltage specifications .................................................................................................................... 35
Output tolerance specifications ........................................................................................................ 35
Output feature specifications ........................................................................................................... 35
Battery specifications ............................................................................................................................... 35
Battery runtime ........................................................................................................................................ 36
Environmental specifications ..................................................................................................................... 36
Serial communications port pin assignment ................................................................................................. 36
Spares ....................................................................................................................................... 38
Ordering spares ...................................................................................................................................... 38
UPS spare parts list .................................................................................................................................. 38
Hardware options ................................................................................................................................... 38
Support and other resources ........................................................................................................ 39
Before you contact HP.............................................................................................................................. 39
HP contact information ............................................................................................................................. 39
Warranty information .................................................................................................................. 40
Limited warranty ..................................................................................................................................... 40
$250,000 Computer Load Protection Guarantee ......................................................................................... 40
Pre-Failure Battery Warranty ..................................................................................................................... 40
Recommended duration of use .................................................................................................................. 41
Regulatory compliance notices ..................................................................................................... 42
Regulatory compliance identification numbers ............................................................................................. 42
Federal Communications Commission notice ............................................................................................... 42
FCC rating label ............................................................................................................................ 42
FCC Notice, Class A Equipment ...................................................................................................... 42
FCC Notice, Class B Equipment ...................................................................................................... 42
Declaration of conformity for products marked with the FCC logo, United States only ....................................... 43
Modifications .......................................................................................................................................... 43
Cables ................................................................................................................................................... 43
Canadian notice (Avis Canadien) .............................................................................................................. 43
European Union regulatory notice ............................................................................................................. 44
Disposal of waste equipment by users in private households in the European Union ......................................... 44
Japanese notice ...................................................................................................................................... 45
BSMI notice ............................................................................................................................................ 45
Contents
4
Korean notice ......................................................................................................................................... 45
Battery replacement notice........................................................................................................................ 46
Power cord statement for Japan................................................................................................................. 46
Electrostatic discharge ................................................................................................................. 47
Preventing electrostatic discharge .............................................................................................................. 47
Grounding methods to prevent electrostatic discharge .................................................................................. 47
Acronyms and abbreviations ........................................................................................................ 48
Documentation feedback ............................................................................................................. 49
Index ......................................................................................................................................... 50
Contents
5
Component identification
UPS R1500 G3 overview
The HP UPS R1500 G3 features a 1U rack-mount design and offers power protection for loads up to 1440
VA/1000 W (NA), 1200 VA/900 W (JPN/TWN) or 1500 VA/1000 W (INTL).
To benefit from the latest product enhancements, update to the latest versions of UPS firmware and software.
NOTE: To download the latest versions of UPS firmware and software, see the HP website
(http://www.hp.com/go/rackandpower).
UPS front panel
Item
Description
1
Battery compartment
2
Control buttons and LED display
Component identification 6
UPS front panel controls
Item
Description
Function
1
Power On/Standby button
Powers up the UPS ("Powering up the UPS" on page 17).
Powers down the UPS ("Powering down the UPS" on page
21).
2
Test/Alarm Reset button
Initiates a self-test ("Initiating a self-test" on page 20).
Silences UPS alarms ("Silencing an audible alarm" on page
20).
UPS front panel LED indicators
Component identification 7
Item
LED description
1
Load Segment 2
2
Load Segment 1
3
General Alarm
4
On Battery
5
Overload
6
Power On
For more information, see "LED and audible alarm troubleshooting (on page 31)."
UPS R1500 G3 NA/JPN/TWN rear panel
Item
Description
1
UPS option card slot
2
USB communications port
3
Site Wiring Fault LED
4
Serial communications port
5
Network Transient Protector IN jack
6
Voltage configuration DIP switches
7
Network Transient Protector OUT jack
8
Load segment 1 (two NEMA 5-15 output receptacles for surge
and battery backup protection)
9
Load segment 2 (two NEMA 5-15 output receptacles for surge
and battery backup protection)
10
Input power cord with NEMA 5-15 plug (BSMI approved for
TWN)
Component identification 8
UPS R1500 G3 INTL rear panel
Item
Description
1
UPS option card slot
2
Input power connector (IEC-320-C14 power inlet)
3
Input circuit breaker
4
USB communications port
5
Serial communications port
6
Network Transient Protector IN jack
7
Voltage configuration DIP switches
8
Network Transient Protector OUT jack
9
Load segment 1 (two IEC-320-C13 output receptacles for
surge and battery backup protection)
10
Load segment 2 (two IEC-320-C13 output receptacles for
surge and battery backup protection)
Component identification 9
Installation
Precautions
Save these instructions. This document contains important safety instructions that should be followed during
installation, operation, and maintenance of the UPS and batteries.
WARNING: A risk of personal injury from electric shock and hazardous energy levels exists. The
installation of options and routine maintenance and service of this product must be performed by
individuals who are knowledgeable about the procedures, precautions, and hazards associated
with AC power products.
WARNING: To prevent personal injury from earth conductor leakage current:
• Do not operate the UPS while disconnected from the utility power source.
• Disconnect load devices before disconnecting the UPS from the utility power source.
WARNING: To prevent personal injury, prepare the area and observe all materials handling
procedures when transporting the UPS. When fully assembled, the UPS weighs 23 kg (50.5 lb).
Preparing to install the hardware
Before installing the hardware:
1.
Be sure the necessary tools and materials ("Tools required" on page 10) are available.
2.
Select an installation site ("Selecting a site" on page 10).
3.
Prepare the equipment ("Readying the equipment" on page 11) for installation in the rack.
Tools required
A Philips screwdriver is required.
Selecting a site
WARNING: To prevent fire or electric shock, install the unit in a temperature- and
humidity-controlled indoor environment, free of conductive contaminants.
When selecting a site, consider the following factors:
•
Elevated operating ambient temperature—If the equipment is installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment might be greater than room
ambient temperature. Install the equipment in an environment compatible with the operating
temperature ("Environmental specifications" on page 36).
•
Reduced air flow—In the rack, the rate of air flow required for safe operation of the equipment must not
be compromised.
Installation 10
•
Circuit overloading—Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of the circuits might have on overcurrent protection and supply
wiring. Appropriate consideration of equipment nameplate ratings should be used when addressing
this concern.
•
Reliable earthing—Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connections to the branch circuit, such
as the use of power strips.
•
Electrical requirements—All models require a dedicated (unshared) branch circuit, suitably rated for the
specific UPS as stated in "Input specifications ("UPS input specifications" on page 34)" .
Readying the equipment
1.
Check the battery recharge date specified on the label that is affixed to the shipping carton.
IMPORTANT: Do not use the battery if the recharge date has passed. If the date on the battery
recharge date label has passed without the battery being recharged, contact an HP authorized
service representative for directions.
2.
Transport the packaged unit to its installation location.
3.
Unpack the equipment near the rack where the unit will be assembled.
CAUTION: Always plan the rack installation so that the heaviest item is on the bottom of the rack.
Install the heaviest item first, and continue to populate the rack from the bottom to the top.
Installing the UPS
Before installing the unit, review and adhere to all warnings provided in "Precautions (on page 10)."
WARNING: A risk of personal injury or damage to the equipment exists. Uneven loading of
equipment in the rack might cause the rack to become unstable. Install the heavier components
first, and then continue to populate the rack from the bottom to the top.
1.
Install the mounting rails.
Installation 11
2.
Attach the chassis to the rack using the supplied screws.
3.
(optional) Insert the rear stabilization brackets into the mounting rails and then attach the brackets to the
UPS.
Connecting the batteries
WARNING: The unit contains sealed lead-acid battery modules. To prevent fire or chemical
burns:
•
•
•
•
•
Do
Do
Do
Do
Do
not
not
not
not
not
attempt to recharge batteries after removal from the unit.
disassemble, crush, or puncture the batteries.
short the external contacts of the batteries.
immerse the batteries in water.
expose to temperatures higher than 40°C (104°F).
Installation 12
WARNING: To prevent personal injury from hazardous energy:
• Remove watches, rings, or other metal objects.
• Use tools with insulated handles.
• Do not place tools or metal parts on top of batteries.
IMPORTANT: Before performing the following tasks, be sure that the unit is powered down and
disconnected from the utility power source.
NOTE: A small amount of arcing may occur when connecting the batteries. This is normal and
does not damage the unit or present any safety concern.
Connect the battery lead to the battery terminal.
Attaching the UPS front bezel
Installation 13
Selecting the UPS voltage configuration
Using a small tool, position the DIP switches according to the desired voltage configuration.
NOTE: An asterisk (*) indicates the default setting.
Output voltage
Input voltage range
DIP switch 1
DIP switch 2
90–106 V
Down
Down
99–116 V
Down
Up
110 V
99–116 V
Down
Up
120 V*
108–127 V
Up
N/A
220 V
198–233 V
Down
Up
230 V*
207–243 V
Up
N/A
240 V
216–254 V
Down
Down
R1500 G3 JPN/TWN 100 V*
110 V
R1500 G3 NA
R1500 G3 INTL
Connecting the host computer
CAUTION: Only one communications port can be connected to the host computer. Connecting
more than one will result in unexpected UPS behavior. If an option card is installed, the serial and
USB communications ports are automatically disabled.
Connect the UPS to a host computer using either the USB cable or the DB9 serial cable included with the UPS.
Install HP Power Protector on the host computer. See the HP website
(http://www.hp.com/go/rackandpower) to download the latest version of HP Power Protector.
NOTE: To install and configure the software, see the software user guide. The software user
guide is available for download from the HP website (http://www.hp.com/go/rackandpower).
Connecting the serial communications port
CAUTION: Use only the computer interface cable supplied with the UPS to connect the
communications port to the host computer.
Installation 14
IMPORTANT: Power protector software requires the communications port to be appropriately
cabled to the host computer.
CAUTION: Only one communications port can be connected to the host computer. Connecting
more than one will result in unexpected UPS behavior. If an option card is installed, the serial and
USB communications ports are automatically disabled.
For information about serial port pin assignment, see "Serial communications port pin assignment (on page
36)" .
Connecting the USB communications port
Connecting the Network Transient Protectors
CAUTION: To avoid damaging the equipment, use the Network Transient Protector with a
standard telephone line only, not with a digital PBX.
NOTE: Do not connect any telephone or fax/modem equipment (RJ-11) to the 230V models;
only connect network cable (RJ-45) to the 230V models.
To protect equipment against surges over a network data line:
1.
Connect the network wall jack to the UPS Network Transient Protector IN jack.
Installation 15
2.
Connect the equipment to the UPS Network Transient Protector OUT jack.
Connecting the UPS to utility power
WARNING: To prevent injury from electric shock or damage to the equipment:
• Plug the input line cord into a grounded (earthed) electrical outlet that is installed near the
equipment and is easily accessible.
• Do not disable the grounding plug on the input line cord. The grounding plug is an important
safety feature.
• Do not use extension cords.
1.
Connect the input power cord to the IEC-320-C14 input power connector on the UPS rear panel (INTL
model only).
2.
Connect the UPS power cord to a grounded utility power outlet. When the UPS is connected, the
batteries begin to charge. Power to the output receptacles designated for surge and battery backup is
not available until the unit is powered up.
For more information about receptacle control, see "Power protector software (on page 29)" .
Connecting devices to the UPS
CAUTION: Do not plug laser printers into the UPS output receptacles. The instantaneous current
drawn by this type of printer can overload the UPS.
Before connecting devices, verify that the UPS will not overload by checking that the ratings of the devices do
not exceed the UPS capacity. If the equipment rating is listed in amps, multiply the number of amps by the
selected output voltage to determine the VA.
After verifying that the UPS will not overload:
•
Connect the device power cords to the output receptacles on the rear panel of the UPS (NA/JPN/TWN
model).
-or-
•
Connect devices to the output receptacles on the rear panel of the UPS using the jumper cords included
with the UPS (INTL model).
Installation 16
Charging the UPS batteries
Allow the batteries to charge before putting the UPS into service.
IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to
devices. The batteries charge to:
• 90% of their capacity within 24 hours
• 100% of their capacity within 48 hours
Powering up the UPS
Press and hold the Power On/Standby button (1) until the UPS beeps. The Power On, Load 1 and Load 2
LEDs illuminate, indicating that power is available at the UPS output receptacles.
Installing the optional UPS Network Module
NOTE: It is not necessary to power down the UPS before installing the UPS Network Module.
Installation 17
1.
Remove the two screws securing the UPS option slot cover plate, and then remove the cover plate.
2.
Install the UPS Network Module along the alignment channels in the option slot.
3.
Secure the UPS Network Module using the two screws removed in step 1.
Installation 18
4.
If the UPS is powered up, you can be sure that the UPS Network Module is seated properly and
communicating with the UPS by verifying that the UPS Data LED illuminates solid green, and then flashes
regularly after 2 minutes.
Connecting the UPS Network Module
The UPS Network Module card is provided to manage the attached servers. RJ 45 network patch panel
cables are required to use this card.
The RJ 45 network patch panel cables are not included.
Installation 19
UPS operations
Modes of operation
The UPS has two modes of operation:
•
Operate mode (on page 20)
•
Battery mode (on page 20)
Operate mode
In Operate mode:
•
Power is available at the UPS receptacles.
•
The UPS charges the batteries as necessary.
The UPS can be placed in Operate mode if either of the following conditions applies:
•
The UPS is powered up.
•
The UPS is powered down and no utility power is available.
To place the UPS in Operate mode, press and hold the Power On/Standby button ("UPS front panel controls"
on page 7) until the UPS acknowledges compliance with a short beep. The Power On, Load 1 and Load 2
LEDs ("UPS front panel LED indicators" on page 7) illuminate, indicating that power is available at the UPS
output receptacles.
Battery mode
In Battery mode, the UPS supplies power without being connected to utility power.
To power up the UPS without using utility power, press and hold the Power On/Standby button ("UPS front
panel controls" on page 7) for two seconds.
Initiating a self-test
To initiate a self-test, press and hold the Test/Alarm Reset button ("UPS front panel controls" on page 7) for
three seconds.
Because a portion of the self-test requires battery power, the self-test cannot be initiated if the batteries are
less than 90 percent charged. If the UPS detects a problem, the appropriate LED ("UPS front panel LED
indicators" on page 7) illuminates and an audible alarm may sound.
For information on what to do if the self-test detects a problem, see "Troubleshooting (on page 31)."
Silencing an audible alarm
To silence an alarm, press the Test/Alarm Reset button ("UPS front panel controls" on page 7).
UPS operations
20
IMPORTANT:
• Although the audible alarm silences, the condition that caused the alarm to sound might still
exist.
• If a utility power failure caused the alarm (or the General Alarm LED illuminates yellow), the
alarm silences after power is restored.
For information about audible alarm conditions, see "LED and audible alarm troubleshooting (on page 31)."
Powering down the UPS
1.
Shut down all connected load devices.
2.
Press the Power On/Standby button. Power to the output receptacles ceases.
3.
Disconnect the UPS from utility power.
4.
Wait at least 60 seconds for the UPS internal circuitry to discharge.
UPS operations
21
Maintenance
Removing the UPS front bezel
Replacing the batteries
To replace the batteries:
1.
Read and observe the requirements in "Important battery safety information (on page 22)" and "Battery
care and storage guidelines (on page 23)."
2.
Follow the instructions in "UPS battery replacement procedure (on page 23)."
Important battery safety information
WARNING: The unit contains sealed lead-acid battery modules. To prevent fire or chemical
burns:
•
•
•
•
•
Do
Do
Do
Do
Do
not
not
not
not
not
attempt to recharge batteries after removal from the unit.
disassemble, crush, or puncture the batteries.
short the external contacts of the batteries.
immerse the batteries in water.
expose to temperatures higher than 60°C (140°F).
WARNING: To prevent personal injury from hazardous energy:
• Remove watches, rings, or other metal objects.
• Use tools with insulated handles.
• Do not place tools or metal parts on top of batteries.
Maintenance
22
NOTE: Replace all battery modules at the same time.
Battery care and storage guidelines
CAUTION: Because of the short shelf life of the batteries, avoid storing a battery spare as a
backup. Do not maintain an inventory of spare batteries on site unless a procedure to keep these
batteries charged while in storage is implemented.
To maintain the batteries:
•
Minimize the amount of time the UPS uses battery power by matching the UPS configuration with the
utility voltage. See "Selecting the UPS voltage configuration (on page 14)."
•
Keep the area around the UPS clean and dust-free. If the environment is very dusty, clean the outside of
the UPS regularly with a vacuum cleaner.
•
Maintain the ambient temperature at 25°C (77°F).
•
If storing a UPS for an extended period, recharge the batteries every 6 months, and then update the
battery recharge date label.
UPS battery replacement procedure
This component is hot-swappable and can be replaced without powering down the UPS.
1.
(optional) To replace the component with the UPS powered down, refer to "Powering down the UPS (on
page 21)."
2.
Remove the UPS front bezel ("Removing the UPS front bezel" on page 22).
3.
Disconnect the battery leads.
Maintenance
23
4.
Remove the battery bracket.
5.
Remove the UPS battery modules.
IMPORTANT: Do not pull the battery leads when removing or installing the batteries.
To replace the component, reverse the removal procedure.
IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to
devices. The batteries charge to:
• 90% of their capacity within 24 hours
• 100% of their capacity within 48 hours
Maintenance
24
Testing the new battery module
After installing the new battery module, press the Test/Alarm Reset button. For information on initiating a
self-test, see "Initiating a self-test (on page 20)."
IMPORTANT: The UPS does not execute a self-test until the batteries are 90 percent charged.
If the installation has been successful, the UPS enters Operate mode. If the installation has not been
successful, the alarm beeps, the On Battery LED illuminates, and the General Alarm LED flashes. If this occurs,
repeat the procedures in "Replacing the batteries (on page 22)," and check the battery terminal connections.
If the condition persists, see "Troubleshooting (on page 31)."
IMPORTANT: Charge the batteries for at least 24 hours before supplying backup power to
devices. The batteries charge to:
• 90% of their capacity within 24 hours
• 100% of their capacity within 48 hours
Replacing the UPS
To remove the UPS:
1.
Power down all attached load devices.
2.
Power down the UPS ("Powering down the UPS" on page 21).
3.
Unplug the UPS power cord.
4.
Disconnect the communications cable.
5.
Unplug the load devices.
6.
Remove the UPS front bezel ("Removing the UPS front bezel" on page 22).
7.
Remove the UPS battery bracket.
8.
Remove the UPS battery modules.
9.
Remove the screws securing the UPS to the rack.
10.
Remove the UPS from the rack.
To replace the component, reverse the removal procedure.
Replacing the UPS option card
This component is hot-swappable and can be replaced without powering down the UPS.
1.
(optional) To replace the component with the UPS powered down, refer to "Powering down the UPS (on
page 21)."
Maintenance
25
2.
Remove the two screws securing the option card, and then slide the card out.
To replace the component, reverse the removal procedure.
CAUTION: Only one communications port can be connected to the host computer. Connecting
more than one will result in unexpected UPS behavior. If an option card is installed, the serial and
USB communications ports are automatically disabled.
NOTE: Replacing the option card might require power protector software to be restarted or
reconfigured.
Updating the UPS firmware
To update the UPS firmware, see the HP website (http://www.hp.com/go/rackandpower).
Configuring a USB to serial converter
NOTE: This procedure was tested on the Windows® XP Professional, Windows Server® 2003,
and Windows® Vista Enterprise operating systems using the HP USB to serial converter (part
number 304098-001). Depending on your system configuration, a driver download might be
required to successfully install the converter. The driver can be downloaded from the USB-Drivers
website (http://www.usb-drivers.com/drivers/123/123294.htm).
To configure a USB port to the COM 1 port on systems that do not have available serial ports:
1.
Connect the USB to serial converter to the USB port on your system.
2.
For Windows Vista, click Start, select Control Panel, double-click System and Maintenance, and then
skip to step 4.
-orFor Windows XP, click Start, select Control Panel, click Performance and Maintenance, and then click
System.
-or-
Maintenance
26
For Windows Server, click Start, select Control Panel, and then double-click System.
3.
Click the Hardware tab.
4.
Click Device Manager. The Device Manager screen appears.
5.
In the tree displayed in the left panel, click the Ports (COM & LPT) branch to expand.
6.
Double-click the port that is assigned to your USB to serial converter device. This port is usually named
with the device manufacturer's name followed by one of the following:
o
USB to Serial Bridge (COM 4)
o
USB Serial port
o
Communications Port (COM1)
The Port Properties screen appears.
7.
Click the Port Settings tab. The Port Settings screen appears.
8.
Click Restore Defaults. The following default settings appear:
o
Bits per second: 9600
o
Data Bits: 8
o
Parity: None
o
Stop bits: 1
o
Flow control: None
9.
Click Advanced. The Advanced Settings screen appears.
10.
From the COM Port Number drop down menu, select Com 1 for the USB port number, and then click
OK.
If COM 1 is being used by another USB port, the following message appears:
This COM name is being used by another device. Using duplicate names can lead
to inaccessible devices and changed settings. Do you want to continue?
If this message appears, click YES. It might be necessary to disable the program accessing COM 1.
a. Click OK.
b. For Windows Vista, skip to step 13.
11.
For Windows Server, reduce the Receive Buffer and Transmit Buffer to the low setting by scrolling down
to select low (1).
12.
Be sure that the Use FIFO buffers (requires 16550 compatible UART) checkbox is selected.
For Windows XP, the USB settings might be different. Choose the lowest, most dependable Receive and
Transmit buffers by using the list menus, radio buttons, or other selection methods.
13.
Click OK to close the Advanced screen.
14.
Click OK to close the Device Manager screen.
15.
Run the firmware Flash batch file program. Follow the instructions provided with the program.
Reassigning the USB COM ports
To reassign a device from COM 1 to another port:
1.
From the open Device Manager screen, locate the USB device that is assigned to COM 1.
2.
Double-click the port name.
The Port Properties screen appears.
Maintenance
27
3.
Click the Port Settings tab.
The Port Settings screen appears.
4.
Click Advanced.
The Advanced Settings screen appears.
5.
Select an available USB port number from the COM Port Number drop down menu.
6.
Click OK to close the Advanced screen.
7.
Click OK to close the Port Settings screen.
8.
Verify that the Device Manager screen shows that the USB to serial converter is assigned to COM 1,
and that the other USB device is assigned to a different port.
If the Device Manager screen does not automatically refresh to show the change:
a. Click Action.
The Action Menu appears.
b. Click Scan for hardware changes to refresh the screen and display the changes.
Maintenance
28
Power management
Power Protector software
HP Power Protector software ensures maximum power reliability of computer systems through comprehensive
control of UPSs. The easy-to-use browser interface enables novice users to configure and manage power
protection settings. To download the latest version of HP Power Protector software, see the HP website
(http://www.hp.com/go/rackandpower).
NOTE: To install and configure the software, see the software user guide. The software user
guide is available for download from the HP website (http://www.hp.com/go/rackandpower).
HP Power Protector:
•
Does not require complex management systems, which simplifies deployment, configuration, and
management of UPS-protected environments.
•
Manages a graceful shutdown of attached devices during utility power failures.
•
Prioritize the shutdown timing of attached computers.
•
Customizes alert generation with modifiable dialog boxes, command execution, and email and
broadcast messages.
•
Monitors the status of the UPS and reports alarms.
•
Displays a power log for analysis.
•
Manages independent UPS load segments to provide separate power control of attached load devices.
The HP UPS Network Module (P/N AF465A) is a Minislot with an easy-to-use browser interface, which gives
you comprehensive control of the UPS and enables you to monitor and effectively manage power
environments. The UPS Network Module supports either a single UPS configuration or a dual redundant UPS
configuration for no single-point-of-failure.
The UPS Network Module can be configured to send alert traps to HP Systems Insight Manager and other
SNMP management programs or used as a stand-alone management system. This flexibility enables you to
monitor and manage UPSs through the network. To facilitate day-by-day maintenance tasks, the embedded
management software provides detailed system logs.
The UPS Network Module provides remote management of a UPS by connecting the UPS directly to the
network. Configuration and management of the UPS from anywhere and at any time through a standard web
browser.
The UPS Network Module (Minislot) is ideal for:
•
Small to enterprise-sized customers that will benefit from remotely managing their UPS.
•
Adding protection via the redundant UPS configuration.
•
Gracefully performing scheduled shut-downs of attached equipment.
•
Notifying administrative personnel in the event of a power failure.
•
Prioritizes the timing of attached load device shutdowns.
Power management 29
•
Delays reboot by load segment after a power outage to sequence the startup of system components.
Power management 30
Troubleshooting
LED and audible alarm troubleshooting
Condition
Power On On Battery Overload General
LED
LED
LED
Alarm LED
Audible alarm
Can alarm
be silenced
("Silencing
an audible
alarm" on
page 20)?
(green)
(yellow)
(red)
(red)
UPS operating from
utility
On
Off
Off
Off
No audible alarm
N/A
Buck mode (high
input voltage)
On
Off
Off
Off
No audible alarm
N/A
Boost mode (low
input voltage)
On
Off
Off
Off
No audible alarm
N/A
Over temperature
condition
On
On
Off
Flashing
On—Continuous
No
Battery test failure
Off
On
Off
Flashing
On—Continuous
Yes
Fan failure
On
Off
Off
Flashing
On—Continuous
No
Output short circuit
On
On
On
Flashing
On—Continuous
No
Flashing
Flashing
Flashing
On—3 beeps/10
seconds
No
On
Off
Off
On—2 second
beep
No
No
Power up failure from Flashing
a DC start—Low
battery (no utility
power)
Low battery (no utility Off
power)
Online—UPS power
capacity exceeded
On
Off
On
Off
On—1 second
beep
Overload timeout
Off
Off
On
Flashing
On—Continuous
No
On battery—Input
voltage is out of
range
On
On
Off
Off
On—2 second
beep
Yes
On battery—No
utility power
Off
On
Off
Off
On— 4 second
beep
Yes
On battery—Battery
voltage condition
Flashing
Off
Off
Flashing
On—Continuous
Yes
On
battery—Overload
condition
Off
On
On
Off
On—1 second
beep
No
On battery—Output
voltage is out of
range
Off
Flashing
Off
Flashing
On—Continuous
No
On battery—Output
wave is abnormal
Flashing
Flashing
Off
Flashing
On—Continuous
No
Troubleshooting
31
CAUTION: Only one communications port can be connected to the host computer. Connecting
more than one will result in unexpected UPS behavior. If an option card is installed, the serial and
USB communications ports are automatically disabled.
For the location of individual LEDs, see "UPS front panel LED indicators (on page 7)."
UPS does not start
Action:
1.
Be sure that the power cord is plugged in to a utility power receptacle.
2.
Check the power source at the utility power receptacle.
3.
Allow the UPS batteries to charge for 24 hours.
UPS operates on battery only
Action:
1.
Save your work.
2.
Power down the load devices connected to the UPS output receptacles.
3.
Remove one or more load devices to reduce the power requirements.
4.
Be sure the UPS configuration matches the utility voltage. Refer to "Selecting the UPS voltage
configuration (on page 14)."
UPS frequently switches between utility and battery
power
Action:
1.
Check the input voltage and reconfigure the UPS.
2.
Contact a qualified electrician to verify that the utility power is suitable for the UPS.
UPS does not provide the expected backup time
Action:
1.
If the Overload LED is illuminated, remove one or more load devices to reduce the power requirements.
2.
Power down the UPS ("Powering down the UPS" on page 21).
3.
Verify the batteries are connected.
4.
Allow the UPS batteries to charge for 24 hours.
5.
Initiate a self-test ("Initiating a self-test" on page 20).
6.
During extended power outages, save your work, power down the load devices, and then power down
the UPS ("Powering down the UPS" on page 21) to conserve battery power.
Troubleshooting
32
UPS cannot communicate with the host computer
Action:
•
Verify only one communications port is connected to the host computer ("Connecting the host computer"
on page 14).
•
If an option card is installed, verify the host computer is only connected to the option card. Installing an
option card automatically disables the built-in serial and USB communications ports.
UPS emits a slight clicking noise
Action: The UPS is automatically correcting high or low AC voltage on the utility line. No action is required.
Site wiring condition
Action: Contact a qualified electrician to be sure that:
•
The line and neutral wires are not reversed in the wall outlet.
•
A ground wire connection does not exist.
Troubleshooting
33
Specifications
UPS physical specifications
Parameter
Value
Height
4.5 cm (1.75 in)
Depth
61.21 cm (24.10 in)
Width
44.45 cm (17.5 in)
Weight
23 kg (50.5 lb)
UPS input specifications
NOTE: An asterisk (*) indicates the default setting.
Available settings
Branch circuit
utility voltage
rating (A)
("Selecting the UPS
voltage configuration"
on page 14) (VAC)
Line cord
R1500 G3 NA 50/60 Hz
110, 120*
15 or 20
Power cord with NEMA
5-15 plug
50/60 Hz
100*, 110
15 or 20
Power cord with NEMA
5-15 plug (BSMI
approved for TWN)
220, 230*, 240
16
IEC-320-C14 power
inlet
UPS model
R1500 G3
JPN/TWN
Utility voltage
frequency
(auto-sensing)
R1500 G3 INTL 50/60 Hz
UPS output specifications
UPS model
Output receptacles
R1500 G3 NA/JPN/TWN
4 x NEMA 5-15
R1500 G3 INTL
4 x IEC-320-C13
Power protection specifications
UPS model
VA
Nominal power
rating (W)
Nominal voltage
setting
R1500 G3 NA
1440
1000
110, 120
R1500 G3 JPN/TWN
1200
900
100
1320
1000
110
Specifications
34
UPS model
VA
Nominal power
rating (W)
Nominal voltage
setting
R1500 G3 INTL
1500
1000
220, 230, 240
Voltage specifications
Configuration setting (VAC)
Available nominal output voltage (VAC)
100
100
110
110
120
120
220
220
230
230
240
240
Output tolerance specifications
Source of power
Regulation
Utility power (nominal
range)
-10% to +6% of nominal output voltage rating (within the
guidelines of the Computer Business Equipment
Manufacturers Association)
Battery power
±20% of nominal output voltage rating
Output feature specifications
Feature
Specification
Online efficiency
95% nominal input voltage
Voltage wave shape
Sine wave; 5% THD with typical PFC load
Surge suppression
ANSI C62.41 Category A (formerly IEEE 587)
Noise filtering
Full-time EMI/RFI filtering
Battery specifications
Feature
Specification
Type
6 V, 9 AH, sealed, maintenance-free, valve-regulated,
rechargeable, lead-acid battery.
Voltage
The battery modules have a battery string voltage of 36 V.
Charging
Advanced charging for faster recovery. Complete charge takes at
least 48 hours. After approximately 24 hours, the batteries reach
90% charge at default nominal utility voltage and no load.
IMPORTANT: The 48-hour timer for the overall charge cycle triggers at the transition from charge
mode to float mode. For certain conditions such as heavily discharged batteries, battery
condition, and so on, it may take longer than usual to reach float mode. In these cases, it may take
longer than 48 hours to reach the rest mode.
Specifications
35
Battery runtime
Load, percent
Load, watts
Estimated battery runtime at 100% battery charge
20
200
58 minutes
50
500
17 minutes
80
800
8 minutes
100
1000
5 minutes
Environmental specifications
Feature
Specification
Operating temperature
0°C to 35°C (32°F to 95°F)
Nonoperating temperature -15°C to 55°C (5°F to 131°F)
5% to 95%; noncondensing
Relative humidity
Operating altitude
Up to 3,000 m (9,843 ft) above sea level
Nonoperating altitude
Up to 15,000 m (49,212 ft) above sea level
Audible noise
Less than 45 dBA
Serial communications port pin assignment
Pin number Signal name Function
Direction from the UPS
1
Low batt
2
TxD
Low battery relay contact; 20 mA, 30 Vdc contact Out
rating
Transmit to external device
Out
3
RxD
Receive from external device
In
4
DTR
PnP from external device (tied to Pin 6)
In
Specifications
36
Pin number Signal name Function
Direction from the UPS
5
GND
Signal common (tied to chassis)
—
6
DSR
To external device (tied to Pin 4)
Out
7
—
No connection
—
8
AC fail
Out
9
—
AC fail relay contact; 20 mA, 30 Vdc contact
rating
No connection
—
Specifications
37
Spares
Ordering spares
To order a spare, visit the HP website (http://www.hp.com/buy/parts).
To replace parts under warranty, contact an HP authorized service representative.
UPS spare parts list
Item
Spare part number
UPS unit NA
638837-001
UPS unit JPN/TWN
638838-001
UPS unit INTL
638839-001
Battery
418401-001
Hardware options
For information on the supported hardware options, see the HP website
(http://www.hp.com/go/rackandpower).
Spares
38
Support and other resources
Before you contact HP
Be sure to have the following information available before you call HP:
•
Active Health System log
Download and have available an Active Health System log for 3 days before the failure was detected.
For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP
website (http://www.hp.com/go/ilo/docs).
•
Onboard Administrator SHOW ALL report (for HP BladeSystem products only)
For more information on obtaining the Onboard Administrator SHOW ALL report, see the HP website
(http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?lang=en&cc=us&objectID=c
02843807).
•
Technical support registration number (if applicable)
•
Product serial number
•
Product model name and number
•
Product identification number
•
Applicable error messages
•
Add-on boards or hardware
•
Third-party hardware or software
•
Operating system type and revision level
HP contact information
For United States and worldwide contact information, see the Contact HP website
(http://www.hp.com/go/assistance).
In the United States:
•
To contact HP by phone, call 1-800-334-5144. For continuous quality improvement, calls may be
recorded or monitored.
•
If you have purchased a Care Pack (service upgrade), see the Support & Drivers website
(http://www8.hp.com/us/en/support-drivers.html). If the problem cannot be resolved at the website,
call 1-800-633-3600. For more information about Care Packs, see the HP website
(http://pro-aq-sama.houston.hp.com/services/cache/10950-0-0-225-121.html).
Support and other resources
39
Warranty information
Limited warranty
To back up the wide range of features offered with the UPS, a 3-year limited warranty is provided.
$250,000 Computer Load Protection Guarantee
In addition to the limited warranty, a $250,000 Computer Load Protection Guarantee (provided by the
original equipment manufacturer) is offered.
IMPORTANT: The $250,000 Computer Load Protection Guarantee is offered only in The United
States and Canada.
The $250,000 Computer Load Protection Guarantee only applies if:
•
The UPS is plugged into a suitably grounded and wired outlet using no extension cords, adapters, other
ground wires, or other electrical connections.
•
The UPS installation complies with all applicable electrical and safety codes specified by the NEC.
•
The UPS is used under normal operating conditions and users comply with all instructions and labels.
•
The UPS is not damaged by accident (other than a utility power transient), misuse, or abuse.
•
o
The Guarantee applies only to the original end-user and is non-transferable.
o
The Guarantee does not include reimbursement for or restoration of any data loss.
The UPS is either connected directly to an enterprise class PDU, which is then connected directly to a
server, workstation, or personal computer, or the UPS is connected directly to a server, workstation, or
personal computer.
Pre-Failure Battery Warranty
The Pre-Failure Battery Warranty, standard on all UPS units, extends the advantage of a 3-year limited
warranty by applying it to the battery before it actually fails. The Pre-Failure Battery Warranty ensures that the
battery is replaced free of charge when a notification that the battery might fail is received from power
protector software. The battery warranty coverage is 3 years for parts. The warranty for the first year of
ownership includes parts and labor. If battery spares are not available for a particular UPS model, the entire
UPS, including its battery, is replaced.
A Pre-Failure Battery warning is given 30 days before a battery failure. The warning is indicated in one or
both of the following ways:
•
An LED showing the battery is low
•
Notification from power protector software
Warranty information 40
Recommended duration of use
Although tests and a multitude of customer experiences have shown no noticeable performance issues with
UPSs for significant time periods after expiration of the 3-year limited warranty, we strongly recommend
considering replacing UPSs after a maximum of 5 to 6 years of use to assure full functionality and a safe
operating environment. This recommendation does not extend or in any way alter the warranty for UPSs
which is limited to a time period of 3 years and a coverage as stated in the applicable warranty statement.
Warranty information 41
Regulatory compliance notices
Regulatory compliance identification numbers
For the purpose of regulatory compliance certifications and identification, this product has been assigned a
unique regulatory model number. The regulatory model number can be found on the product nameplate
label, along with all required approval markings and information. When requesting compliance information
for this product, always refer to this regulatory model number. The regulatory model number is not the
marketing name or model number of the product.
Federal Communications Commission notice
Part 15 of the Federal Communications Commission (FCC) Rules and Regulations has established Radio
Frequency (RF) emission limits to provide an interference-free radio frequency spectrum. Many electronic
devices, including computers, generate RF energy incidental to their intended function and are, therefore,
covered by these rules. These rules place computers and related peripheral devices into two classes, A and
B, depending upon their intended installation. Class A devices are those that may reasonably be expected
to be installed in a business or commercial environment. Class B devices are those that may reasonably be
expected to be installed in a residential environment (for example, personal computers). The FCC requires
devices in both classes to bear a label indicating the interference potential of the device as well as additional
operating instructions for the user.
FCC rating label
The FCC rating label on the device shows the classification (A or B) of the equipment. Class B devices have
an FCC logo or ID on the label. Class A devices do not have an FCC logo or ID on the label. After you
determine the class of the device, refer to the corresponding statement.
FCC Notice, Class A Equipment
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. Operation of this equipment in a residential area
is likely to cause harmful interference, in which case the user will be required to correct the interference at
personal expense.
FCC Notice, Class B Equipment
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
Regulatory compliance notices
42
radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit that is different from that to which the receiver is
connected.
•
Consult the dealer or an experienced radio or television technician for help.
Declaration of conformity for products marked with
the FCC logo, United States only
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
For questions regarding this product, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 530113
Houston, Texas 77269-2000
•
1-800-HP-INVENT (1-800-474-6836). (For continuous quality improvement, calls may be recorded or
monitored.)
For questions regarding this FCC declaration, contact us by mail or telephone:
•
Hewlett-Packard Company
P. O. Box 692000, Mail Stop 510101
Houston, Texas 77269-2000
•
1­281-514-3333
To identify this product, refer to the part, series, or model number found on the product.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this device that are not
expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in
order to maintain compliance with FCC Rules and Regulations.
Canadian notice (Avis Canadien)
Class A equipment
Regulatory compliance notices
43
This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
Class B equipment
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment
Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur
du Canada.
European Union regulatory notice
Products bearing the CE marking comply with the following EU Directives:
•
Low Voltage Directive 2006/95/EC
•
EMC Directive 2004/108/EC
•
Ecodesign Directive 2009/125/EC, where applicable
CE compliance of this product is valid if powered with the correct CE-marked AC adapter provided by HP.
Compliance with these directives implies conformity to applicable harmonized European standards
(European Norms) that are listed in the EU Declaration of Conformity issued by HP for this product or product
family and available (in English only) either within the product documentation or at the following HP website
(http://www.hp.eu/certificates) (type the product number in the search field).
The compliance is indicated by one of the following conformity markings placed on the product:
For non-telecommunications products and for EU harmonized telecommunications products, such as
Bluetooth® within power class below 10mW.
For EU non-harmonized telecommunications products (If applicable, a 4-digit notified body number is
inserted between CE and !).
Please refer to the regulatory label provided on the product.
The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger
Strasse 140, 71034 Boeblingen, GERMANY.
Disposal of waste equipment by users in private
households in the European Union
Regulatory compliance notices
44
This symbol on the product or on its packaging indicates that this product must not be disposed of
with your other household waste. Instead, it is your responsibility to dispose of your waste
equipment by handing it over to a designated collection point for the recycling of waste electrical
and electronic equipment. The separate collection and recycling of your waste equipment at the
time of disposal will help to conserve natural resources and ensure that it is recycled in a manner
that protects human health and the environment. For more information about where you can drop
off your waste equipment for recycling, please contact your local city office, your household
waste disposal service or the shop where you purchased the product.
Japanese notice
BSMI notice
Korean notice
Class A equipment
Regulatory compliance notices
45
Class B equipment
Battery replacement notice
WARNING: Power products contain sealed lead-acid battery modules. A risk of fire and burns
exists if the battery is not properly handled. To reduce the risk of personal injury:
• Do not attempt to recharge the battery.
• Do not expose the battery to temperatures higher than 60°C (140°F).
• Do not disassemble, crush, puncture, short external contacts, or dispose of in fire or water. The
battery might explode.
Batteries, battery packs, and accumulators should not be disposed of together with the general
household waste. To forward them to recycling or proper disposal, use the public collection system or
return them to HP, an authorized HP Partner, or their agents.
For more information about battery replacement or proper disposal, contact an authorized reseller or an
authorized service provider.
Power cord statement for Japan
Regulatory compliance notices
46
Electrostatic discharge
Preventing electrostatic discharge
To prevent damaging the system, be aware of the precautions you need to follow when setting up the system
or handling parts. A discharge of static electricity from a finger or other conductor may damage system
boards or other static-sensitive devices. This type of damage may reduce the life expectancy of the device.
To prevent electrostatic damage:
•
Avoid hand contact by transporting and storing products in static-safe containers.
•
Keep electrostatic-sensitive parts in their containers until they arrive at static-free workstations.
•
Place parts on a grounded surface before removing them from their containers.
•
Avoid touching pins, leads, or circuitry.
•
Always be properly grounded when touching a static-sensitive component or assembly.
Grounding methods to prevent electrostatic discharge
Several methods are used for grounding. Use one or more of the following methods when handling or
installing electrostatic-sensitive parts:
•
Use a wrist strap connected by a ground cord to a grounded workstation or computer chassis. Wrist
straps are flexible straps with a minimum of 1 megohm ±10 percent resistance in the ground cords. To
provide proper ground, wear the strap snug against the skin.
•
Use heel straps, toe straps, or boot straps at standing workstations. Wear the straps on both feet when
standing on conductive floors or dissipating floor mats.
•
Use conductive field service tools.
•
Use a portable field service kit with a folding static-dissipating work mat.
If you do not have any of the suggested equipment for proper grounding, have an authorized reseller install
the part.
For more information on static electricity or assistance with product installation, contact an authorized
reseller.
Electrostatic discharge
47
Acronyms and abbreviations
IEC
International Electrotechnical Commission
PFC
power factor corrected
PnP
plug and play
UPS
uninterruptible power system
USB
universal serial bus
Acronyms and abbreviations
48
Documentation feedback
HP is committed to providing documentation that meets your needs. To help us improve the documentation,
send any errors, suggestions, or comments to Documentation Feedback (mailto:[email protected]).
Include the document title and part number, version number, or the URL when submitting your feedback.
Documentation feedback
49
Index
A
alarms, silencing 20
authorized reseller 39
B
backup time, insufficient 32
batteries, care and storage 23
batteries, charging 17
batteries, connecting 12
batteries, replacing 22, 23
batteries, runtime 36
batteries, testing 25
battery bracket 23
Battery mode 20
battery replacement notice 46
battery warranty 40
bezel, attaching 13
bezel, removing 23
BSMI notice 45
buttons 6
C
cables 43
Canadian notice 43
charging batteries 17
class A equipment 42
class B equipment 42
components, identification 6, 7
connecting batteries 12
contacting HP 39
environmental specifications 36
European Union notice 44
European Union regulatory notice 44
F
FCC rating label 42
Federal Communications Commission (FCC)
notice 42, 43
firmware, updating 26
frequent switching between battery and utility
power 32
front panel components 6
front panel LEDs 7
G
General Alarm LED, location 7
grounding methods 47
H
hardware options 38
hardware, preparing to install 10
HP technical support 39
I
installation instructions 10
installing the batteries 23
insufficient backup time 32
J
Japanese notice 45
D
K
Declaration of Conformity 43
devices, connecting 16
diagnostics 20
disposal, battery 44, 46
duration of use 41
Korean notices 45
E
electrostatic discharge 47
L
LEDs, troubleshooting 31
limited warranty 40
load protection guarantee 40
Load Segment 1 LED 7
Load Segment 2 LED 7
Index
50
M
maintenance 22
modifications, FCC notice 43
temperature ranges (environmental) 36
testing batteries 25
tools 10
troubleshooting 31
O
U
On Battery LED, location 7
Operate mode 20
operations, UPS 20
option card, replacing 25
ordering spares 38
output feature specifications 35
output tolerance specifications 35
Overload LED, location 7
updating the firmware 26
UPS does not start 32
UPS firmware, updating 26
UPS operations 20
UPS, installing 10
UPS, replacing 25
P
voltage specifications 35
phone numbers 39
pin assignment 36
power cord 46
power LED, location 7
power management 29
powering down 21
preparation procedures 10
W
V
warranties 40
R
recommended duration of use 41
regulatory compliance identification numbers 42
regulatory compliance notices 42, 44
replacing the batteries 22, 23
replacing the option card 25
replacing the UPS 25
required information 39
required tools 10
runtime specifications 36
S
safety considerations 10
selecting a site 10
spares 38
specifications 34
static electricity 47
storing batteries 23
support 39
supported hardware 38
T
technical support 39
telephone numbers 39
Index
51
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement