HP | DL280 | Service and Maintain | HP DL280 Service and Maintain

HP ProLiant DL288 G6 Server
Maintenance and Service Guide
Part number 663204-001
First edition July 2011
Legal notices
© Copyright 2011 Hewlett-Packard Development Company, L.P.
The information contained herein is subject to change without notice. The only warranties for HP products and services are
set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed
as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Intel and Xeon are registered trademarks of Intel Corporation in the U.S. and other countries.
Contents
Customer self repair ............................................................................................................................... 1
Parts only warranty service........................................................................................................................ 1
Illustrated parts catalog ......................................................................................................................... 12
Mechanical components / 4 3.5” HDD model........................................................................................... 12
Mechanical components / 8 3.5” HDD model........................................................................................... 13
Mechanical components / 8 2.5” HDD model........................................................................................... 14
Mechanical components / 12 3.5” HDD model......................................................................................... 15
Mechanical components / 25 2.5” HDD model......................................................................................... 16
System components / 4 3.5” HDD model ................................................................................................. 20
System components / 8 3.5” HDD model ................................................................................................. 24
System components / 8 2.5” HDD model ................................................................................................. 27
System components / 12 3.5” HDD model ............................................................................................... 30
System components /25 2.5” HDD model ................................................................................................ 33
HP contact information ........................................................................................................................... 37
Before you contact HP ............................................................................................................................ 37
Removal and replacement procedures .................................................................................................... 39
Hardware configuration tools .................................................................................................................. 39
Hardware configuration information......................................................................................................... 39
Electrostatic discharge information ...................................................................................................... 39
Pre-installation procedure ................................................................................................................... 40
Post-installation instructions ................................................................................................................. 40
Server warnings and cautions.................................................................................................................. 40
HP Trusted Platform Module................................................................................................................ 41
Symbols on equipment............................................................................................................................ 41
Powering down the server ....................................................................................................................... 42
System cover ......................................................................................................................................... 43
Top cover......................................................................................................................................... 43
Drives................................................................................................................................................... 44
Cable management........................................................................................................................... 44
Cable connections ............................................................................................................................ 45
Drive bay configuration ..................................................................................................................... 49
Optical disc drive bay ....................................................................................................................... 52
Hard drives ...................................................................................................................................... 55
SAS/SATA HDD backplane ............................................................................................................... 61
System board configuration..................................................................................................................... 70
Processor ......................................................................................................................................... 70
Memory........................................................................................................................................... 79
DIMM identification........................................................................................................................... 82
PCI expansion card ........................................................................................................................... 83
Dedicated management port (Optional) ............................................................................................. 102
TPM Module (Optional) ................................................................................................................... 105
System battery ................................................................................................................................ 107
BBWC (Optional)............................................................................................................................ 110
System board removal and replacement procedure .................................................................................. 112
Power supply unit (PSU) ........................................................................................................................ 114
System fan cage .................................................................................................................................. 117
System fan .......................................................................................................................................... 122
Connectors, switches, and LEDs ........................................................................................................... 125
Connectors and components ................................................................................................................. 125
Front panel components ................................................................................................................... 125
Rear panel components ................................................................................................................... 130
System board components................................................................................................................ 133
Jumpers ......................................................................................................................................... 134
LED indicators ..................................................................................................................................... 135
Front panel LED indicators ................................................................................................................ 135
Optical disc drive activity LED indicator ............................................................................................. 136
Hard drive LED indicator.................................................................................................................. 137
Rear panel LED indicators ................................................................................................................ 138
System board LED indicator.............................................................................................................. 139
Diagnostic tools and setup utilities ........................................................................................................ 140
BIOS software ..................................................................................................................................... 140
BIOS Setup Utility ................................................................................................................................ 140
Accessing the BIOS Setup Utility ............................................................................................................ 140
Navigating through the Setup Utility .................................................................................................. 141
Setup Utility menu bar ..................................................................................................................... 142
BIOS update ....................................................................................................................................... 148
Clear CMOS....................................................................................................................................... 148
Power-On Self-Test (POST)..................................................................................................................... 148
POST error indicators ...................................................................................................................... 149
POST error descriptions ................................................................................................................... 149
POST related troubleshooting............................................................................................................ 150
SETSYS utility.................................................................................................................................. 151
Physical and operating specifications ................................................................................................... 152
System unit.......................................................................................................................................... 152
Index ................................................................................................................................................ 157
Customer self repair
HP products are designed with many Customer Self Repair (CSR) parts to minimize repair time and
allow for greater flexibility in performing defective parts replacement. If during the diagnosis period
HP (or HP service providers or service partners) identifies that the repair can be accomplished by the
use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of
CSR parts:
•
Mandatory—Parts for which customer self repair is mandatory. If, however, you require that
HP replace them for you, there may or may not be additional charges, depending on the type of
warranty service designated for your product.
•
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are
identified as "No" in the Illustrated Parts Catalog.
Based on availability and where geography permits, CSR parts will be shipped for next business day
delivery. Same day or four-hour delivery may be offered at an additional charge where geography
permits. If assistance is required, you can call the HP Technical Support Center and a technician will
help you over the telephone. HP specifies in the materials shipped with a replacement CSR part
whether a defective part must be returned to HP. In cases where it is required to return the defective
part to HP, you must ship the defective part back to HP within a defined period of time, normally five
(5) business days. The defective part must be returned with the associated documentation in the
provided shipping material. Failure to return the defective part may result in HP billing you for the
replacement. With a customer self repair, HP will pay all shipping and part return costs and
determine the courier/carrier to be used.
For more information about HP's Customer Self Repair program, contact your local service provider.
For the North American program, refer to the HP website (http://www.hp.com/go/selfrepair).
Parts only warranty service
Your HP Limited Warranty may include a parts only warranty service. Under the terms of parts only
warranty service, HP will provide replacement parts free of charge.
For parts only warranty service, CSR part replacement is mandatory. If you request HP to replace
these parts, you will be charged for the travel and labor costs of this service.
Customer self repair
1
Réparation par le client (CSR)
Les produits HP comportent de nombreuses pièces CSR (Customer Self Repair = réparation par le
client) afin de minimiser les délais de réparation et faciliter le remplacement des pièces défectueuses.
Si pendant la période de diagnostic, HP (ou ses partenaires ou mainteneurs agréés) détermine que la
réparation peut être effectuée à l'aide d'une pièce CSR, HP vous l'envoie directement. Il existe deux
catégories de pièces CSR:
•
Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service
vous seront facturés.
•
Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le
type de garantie applicable à votre produit.
REMARQUE: Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même
la réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention "Non" dans le
Catalogue illustré.
Les pièces CSR sont livrées le jour ouvré suivant, dans la limite des stocks disponibles et selon votre
situation géographique. Si votre situation géographique le permet et que vous demandez une
livraison le jour même ou dans les 4 heures, celle-ci vous sera facturée. Pour bénéficier d'une
assistance téléphonique, appelez le Centre d'assistance technique HP. Dans les documents envoyés
avec la pièce de rechange CSR, HP précise s'il est nécessaire de lui retourner la pièce défectueuse. Si
c'est le cas, vous devez le faire dans le délai indiqué, généralement cinq (5) jours ouvrés. La pièce et
sa documentation doivent être retournées dans l'emballage fourni. Si vous ne retournez pas la pièce
défectueuse, HP se réserve le droit de vous facturer les coûts de remplacement. Dans le cas d'une
pièce CSR, HP supporte l'ensemble des frais d'expédition et de retour, et détermine la société de
courses ou le transporteur à utiliser.
Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour
plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP
(http://www.hp.com/go/selfrepair).
Service de garantie "pièces seules"
Votre garantie limitée HP peut inclure un service de garantie "pièces seules". Dans ce cas, les pièces
de rechange fournies par HP ne sont pas facturées.
Dans le cadre de ce service, la réparation des pièces CSR par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
Customer self repair
2
Riparazione da parte del cliente
Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti
difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati
direttamente dal cliente (CSR, Customer Self Repair). Se in fase di diagnostica HP (o un centro di
servizi o di assistenza HP) identifica il guasto come riparabile mediante un ricambio CSR, HP lo
spedirà direttamente al cliente per la sostituzione. Vi sono due categorie di parti CSR:
•
Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente ne
affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
•
Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque di
componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il
prodotto.
NOTA: alcuni componenti HP non sono progettati per la riparazione da parte del cliente. Per
rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un "No" nel Catalogo illustrato dei componenti.
In base alla disponibilità e alla località geografica, le parti CSR vengono spedite con consegna entro
il giorno lavorativo seguente. La consegna nel giorno stesso o entro quattro ore è offerta con un
supplemento di costo solo in alcune zone. In caso di necessità si può richiedere l'assistenza telefonica
di un addetto del centro di supporto tecnico HP. Nel materiale fornito con una parte di ricambio CSR,
HP specifica se il cliente deve restituire dei componenti. Qualora sia richiesta la resa ad HP del
componente difettoso, lo si deve spedire ad HP entro un determinato periodo di tempo, generalmente
cinque (5) giorni lavorativi. Il componente difettoso deve essere restituito con la documentazione
associata nell'imballo di spedizione fornito. La mancata restituzione del componente può comportare
la fatturazione del ricambio da parte di HP. Nel caso di riparazione da parte del cliente, HP sostiene
tutte le spese di spedizione e resa e sceglie il corriere/vettore da utilizzare.
Per ulteriori informazioni sul programma CSR di HP contattare il centro di assistenza di zona. Per il
programma in Nord America fare riferimento al sito Web HP (http://www.hp.com/go/selfrepair).
Servizio di garanzia per i soli componenti
La garanzia limitata HP può includere un servizio di garanzia per i soli componenti. Nei termini di
garanzia del servizio per i soli componenti, HP fornirà gratuitamente le parti di ricambio.
Per il servizio di garanzia per i soli componenti è obbligatoria la formula CSR che prevede la
riparazione da parte del cliente. Se il cliente invece richiede la sostituzione ad HP, dovrà sostenere le
spese di spedizione e di manodopera per il servizio.
Customer self repair
3
Customer self repair
HP Produkte enthalten viele CSR-Teile (Customer Self Repair), um Reparaturzeiten zu minimieren und
höhere Flexibilität beim Austausch defekter Bauteile zu ermöglichen. Wenn HP (oder ein HP
Servicepartner) bei der Diagnose feststellt, dass das Produkt mithilfe eines CSR-Teils repariert werden
kann, sendet Ihnen HP dieses Bauteil zum Austausch direkt zu. CSR-Teile werden in zwei Kategorien
unterteilt:
•
Zwingend—Teile, für die das Customer Self Repair-Verfahren zwingend vorgegeben ist. Wenn
Sie den Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und
Arbeitskosten für diesen Service berechnet.
•
Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind auch
für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag
geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden
gegen einen Aufpreis verfügbar. Wenn Sie Hilfe benötigen, können Sie das HP technische Support
Center anrufen und sich von einem Mitarbeiter per Telefon helfen lassen. Den Materialien, die mit
einem CSR-Ersatzteil geliefert werden, können Sie entnehmen, ob das defekte Teil an HP
zurückgeschickt werden muss. Wenn es erforderlich ist, das defekte Teil an HP zurückzuschicken,
müssen Sie dies innerhalb eines vorgegebenen Zeitraums tun, in der Regel innerhalb von fünf (5)
Geschäftstagen. Das defekte Teil muss mit der zugehörigen Dokumentation in der Verpackung
zurückgeschickt werden, die im Lieferumfang enthalten ist. Wenn Sie das defekte Teil nicht
zurückschicken, kann HP Ihnen das Ersatzteil in Rechnung stellen. Im Falle von Customer Self Repair
kommt HP für alle Kosten für die Lieferung und Rücksendung auf und bestimmt den Kurier/Frachtdienst.
Weitere Informationen über das HP Customer Self Repair Programm erhalten Sie von Ihrem
Servicepartner vor Ort. Informationen über das CSR-Programm in Nordamerika finden Sie auf der HP
Website unter (http://www.hp.com/go/selfrepair).
Parts-only warranty service (Garantieservice
ausschließlich für Teile)
Ihre HP Garantie umfasst möglicherweise einen Parts-only Warranty Service (Garantieservice
ausschließlich für Teile). Gemäß den Bestimmungen des Parts-only Warranty Service stellt HP
Ersatzteile kostenlos zur Verfügung.
Für den Parts-only Warranty Service ist das CSR-Verfahren zwingend vorgegeben. Wenn Sie den
Austausch dieser Teile von HP vornehmen lassen, werden Ihnen die Anfahrt- und Arbeitskosten für
diesen Service berechnet
Customer self repair
4
Reparaciones del propio cliente
Los productos de HP incluyen muchos componentes que el propio usuario puede reemplazar
(Customer Self Repair, CSR) para minimizar el tiempo de reparación y ofrecer una mayor flexibilidad
a la hora de realizar sustituciones de componentes defectuosos. Si, durante la fase de diagnóstico,
HP (o los proveedores o socios de servicio de HP) identifica que una reparación puede llevarse a
cabo mediante el uso de un componente CSR, HP le enviará dicho componente directamente para
que realice su sustitución. Los componentes CSR se clasifican en dos categorías:
•
Obligatorio—componentes para los que la reparación por parte del usuario es obligatoria. Si
solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse cargo de los
gastos de desplazamiento y de mano de obra de dicho servicio.
•
Opcional—componentes para los que la reparación por parte del usuario es opcional. Estos
componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
NOTA: Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra "No" en el catálogo ilustrado de componentes.
Según la disponibilidad y la situación geográfica, los componentes CSR se enviarán para que
lleguen a su destino al siguiente día laborable. Si la situación geográfica lo permite, se puede
solicitar la entrega en el mismo día o en cuatro horas con un coste adicional. Si precisa asistencia
técnica, puede llamar al Centro de asistencia técnica de HP y recibirá ayuda telefónica por parte de
un técnico. Con el envío de materiales para la sustitución de componentes CSR, HP especificará si los
componentes defectuosos deberán devolverse a HP. En aquellos casos en los que sea necesario
devolver algún componente a HP, deberá hacerlo en el periodo de tiempo especificado,
normalmente cinco días laborables. Los componentes defectuosos deberán devolverse con toda la
documentación relacionada y con el embalaje de envío. Si no enviara el componente defectuoso
requerido, HP podrá cobrarle por el de sustitución. En el caso de todas sustituciones que lleve a cabo
el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la
empresa de transporte que se utilice para dicho servicio.
Para obtener más información acerca del programa de Reparaciones del propio cliente de HP,
póngase en contacto con su proveedor de servicios local. Si está interesado en el programa para
Norteamérica, visite la página web de HP siguiente (http://www.hp.com/go/selfrepair).
Servicio de garantía exclusivo de componentes
La garantía limitada de HP puede que incluya un servicio de garantía exclusivo de componentes.
Según las condiciones de este servicio exclusivo de componentes, HP le facilitará los componentes de
repuesto sin cargo adicional alguno.
Para este servicio de garantía exclusivo de componentes, es obligatoria la sustitución de
componentes por parte del usuario (CSR). Si solicita a HP que realice la sustitución de estos
componentes, tendrá que hacerse cargo de los gastos de desplazamiento y de mano de obra de
dicho servicio.
Customer self repair
5
Customer self repair
Veel onderdelen in HP producten zijn door de klant zelf te repareren, waardoor de reparatieduur tot
een minimum beperkt kan blijven en de flexibiliteit in het vervangen van defecte onderdelen groter is.
Deze onderdelen worden CSR-onderdelen (Customer Self Repair) genoemd. Als HP (of een HP
Service Partner) bij de diagnose vaststelt dat de reparatie kan worden uitgevoerd met een CSRonderdeel, verzendt HP dat onderdeel rechtstreeks naar u, zodat u het defecte onderdeel daarmee
kunt vervangen. Er zijn twee categorieën CSR-onderdelen:
•
Verplicht—Onderdelen waarvoor reparatie door de klant verplicht is. Als u HP verzoekt deze
onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
•
Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze onderdelen
zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen voor u te
vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het type
garantieservice voor het product.
OPMERKING: Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In
verband met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner
worden vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt
met "Nee".
Afhankelijk van de leverbaarheid en de locatie worden CSR-onderdelen verzonden voor levering op
de eerstvolgende werkdag. Levering op dezelfde dag of binnen vier uur kan tegen meerkosten
worden aangeboden, indien dit mogelijk is gezien de locatie. Indien assistentie gewenst is, belt u een
HP Service Partner om via de telefoon technische ondersteuning te ontvangen. HP vermeldt in de
documentatie bij het vervangende CSR-onderdeel of het defecte onderdeel aan HP moet worden
geretourneerd. Als het defecte onderdeel aan HP moet worden teruggezonden, moet u het defecte
onderdeel binnen een bepaalde periode, gewoonlijk vijf (5) werkdagen, retourneren aan HP. Het
defecte onderdeel moet met de bijbehorende documentatie worden geretourneerd in het
meegeleverde verpakkingsmateriaal. Als u het defecte onderdeel niet terugzendt, kan HP u voor het
vervangende onderdeel kosten in rekening brengen. Bij reparatie door de klant betaalt HP alle
verzendkosten voor het vervangende en geretourneerde onderdeel en kiest HP zelf welke
koerier/transportonderneming hiervoor wordt gebruikt.
Neem contact op met een Service Partner voor meer informatie over het Customer Self Repair
programma van HP. Informatie over Service Partners vindt u op de HP website
(http://www.hp.com/go/selfrepair).
Garantieservice "Parts Only"
Het is mogelijk dat de HP garantie alleen de garantieservice "Parts Only" omvat. Volgens de
bepalingen van de Parts Only garantieservice zal HP kosteloos vervangende onderdelen ter
beschikking stellen.
Voor de Parts Only garantieservice is vervanging door CSR-onderdelen verplicht. Als u HP verzoekt
deze onderdelen voor u te vervangen, worden u voor deze service reiskosten en arbeidsloon in
rekening gebracht.
Customer self repair
6
Reparo feito pelo cliente
Os produtos da HP são projetados com muitas peças para reparo feito pelo cliente (CSR) de modo a
minimizar o tempo de reparo e permitir maior flexibilidade na substituição de peças com defeito. Se,
durante o período de diagnóstico, a HP (ou fornecedores/parceiros de serviço da HP) concluir que o
reparo pode ser efetuado pelo uso de uma peça CSR, a peça de reposição será enviada diretamente
ao cliente. Existem duas categorias de peças CSR:
•
Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
•
Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia
destinado ao produto.
OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim
de cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas
peças estão identificadas com a marca "No" (Não), no catálogo de peças ilustrado.
Conforme a disponibilidade e o local geográfico, as peças CSR serão enviadas no primeiro dia útil
após o pedido. Onde as condições geográficas permitirem, a entrega no mesmo dia ou em quatro
horas pode ser feita mediante uma taxa adicional. Se precisar de auxílio, entre em contato com o
Centro de suporte técnico da HP para que um técnico o ajude por telefone. A HP especifica nos
materiais fornecidos com a peça CSR de reposição se a peça com defeito deve ser devolvida à HP.
Nos casos em que isso for necessário, é preciso enviar a peça com defeito à HP dentro do período
determinado, normalmente cinco (5) dias úteis. A peça com defeito deve ser enviada com a
documentação correspondente no material de transporte fornecido. Caso não o faça, a HP poderá
cobrar a reposição. Para as peças de reparo feito pelo cliente, a HP paga todas as despesas de
transporte e de devolução da peça e determina a transportadora/serviço postal a ser utilizado.
Para obter mais informações sobre o programa de reparo feito pelo cliente da HP, entre em contato
com o fornecedor de serviços local. Para o programa norte-americano, visite o site da HP
(http://www.hp.com/go/selfrepair).
Serviço de garantia apenas para peças
A garantia limitada da HP pode incluir um serviço de garantia apenas para peças. Segundo os
termos do serviço de garantia apenas para peças, a HP fornece as peças de reposição sem cobrar
nenhuma taxa.
No caso desse serviço, a substituição de peças CSR é obrigatória. Se desejar que a HP substitua
essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
Customer self repair
7
Customer self repair
8
Customer self repair
9
Customer self repair
10
Customer self repair
11
Illustrated parts catalog
Mechanical components / 4 3.5” HDD model
Table 1 Mechanical Components Spare Parts List / 4 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
Air baffle
507256-001
Mandatory1
2
Rail kit
573091-001
Mandatory1
3
Hard drive cage for 4 3.5” HDDs (includes control panel)
507305-001
Mandatory1
4
Hardware/Plastics Kit
507260-001
Mandatory1
507262-001
Mandatory1
ASSY, BLANK,SFF
BRKT, PCI,LOW PROFILE, ARRAY CONT
BRKT,HDD,SLIMLINE,12.7
SCR, M2-0.4x.2.1mm, 6G, PH
SCR TT, 6-32x.160,SLT-T15
BLANK, PS, NONPERF, IDOF
REAR I/O PANEL, LC2UG6
5
Top cover
Illustrated parts catalog 12
Mechanical components / 8 3.5” HDD model
Table 2 Mechanical Components Spare Parts List / 8 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
Air baffle
507256-001
Mandatory1
2
Rail kit
573091-001
Mandatory1
3
Hard drive cage for 8 3.5” HDDs(includes control panel)
507305-001
Mandatory1
4
Hardware/Plastics Kit
507260-001
Mandatory1
507262-001
Mandatory1
ASSY, BLANK,SFF
BRKT, PCI,LOW PROFILE, ARRAY CONT
BRKT,HDD,SLIMLINE,12.7
SCR, M2-0.4x.2.1mm, 6G, PH
SCR TT, 6-32x.160,SLT-T15
BLANK, PS, NONPERF, IDOF
REAR I/O PANEL, LC2UG6
5
Top cover
Illustrated parts catalog 13
Mechanical components / 8 2.5” HDD model
Table 3 Mechanical Components Spare Parts List / 8 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
Air baffle
507256-001
Mandatory1
2
Rail kit
573091-001
Mandatory1
3
Hard drive cage for 8 2.5” HDDs (includes control panel)
507253-001
Mandatory1
4
Hardware/Plastics Kit
507260-001
Mandatory1
507262-001
Mandatory1
ASSY, BLANK,SFF
BRKT, PCI,LOW PROFILE, ARRAY CONT
BRKT,HDD,SLIMLINE,12.7
SCR, M2-0.4x.2.1mm, 6G, PH
SCR TT, 6-32x.160,SLT-T15
BLANK, PS, NONPERF, IDOF
REAR I/O PANEL, LC2UG6
5
Top cover
Illustrated parts catalog 14
Mechanical components / 12 3.5” HDD model
Table 4 Mechanical Components Spare Parts List / 12 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
Air baffle
507256-001
Mandatory1
2
Rail kit
573091-001
Mandatory1
3
Hard drive cage for 12 3.5” HDDs (includes control panel)
587326-001
Mandatory1
4
Hardware/Plastics Kit
536390-001
Mandatory1
507262-001
Mandatory1
ASSY, BLANK,SFF
BRKT, PCI,LOW PROFILE, ARRAY CONT
BRKT,HDD,SLIMLINE,12.7
SCR, M2-0.4x.2.1mm, 6G, PH
SCR TT, 6-32x.160,SLT-T15
BLANK, PS, NONPERF, IDOF
REAR I/O PANEL, LC2UG6
5
Top cover
Illustrated parts catalog 15
Mechanical components / 25 2.5” HDD model
Table 5 Mechanical Components Spare Parts List / 25 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
Air baffle
507256-001
Mandatory1
2
Rail kit
573091-001
Mandatory1
3
Hard drive cage for 25 2.5” HDDs (includes control panel)
530946-001
Mandatory1
4
Hardware/Plastics Kit
507260-001
Mandatory1
507262-001
Mandatory1
ASSY, BLANK,SFF
BRKT, PCI,LOW PROFILE, ARRAY CONT
BRKT,HDD,SLIMLINE,12.7
SCR, M2-0.4x.2.1mm, 6G, PH
SCR TT, 6-32x.160,SLT-T15
BLANK, PS, NONPERF, IDOF
REAR I/O PANEL, LC2UG6
5
Top cover
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Illustrated parts catalog 16
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand- und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional—componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
3
Illustrated parts catalog 17
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
Illustrated parts catalog 18
Illustrated parts catalog 19
The system supports five kinds of HDD configurations, three types of PCI cage and three types of
power supply unit. The following table lists the detailed system configurations.
Table 6 System Configurations
System model
4 3.5” HDD model
PCI cage
Power supply unit
Standard PCI cage
One or two 460 W power supply unit
Optical disc drive PCI cage
8 3.5” HDD model
Standard PCI cage
One or two 460 W power supply unit
Optical disc drive PCI cage
8 2.5” HDD model
Standard PCI cage
One or two 460 W power supply unit
Optical disc drive PCI cage
12 3.5” HDD model
Standard PCI cage
One or two 750 W power supply unit
Optical disc drive PCI cage
HDD PCI cage
25 2.5” HDD model
Standard PCI cage
One or two 750W power supply unit
Optical disc drive PCI cage
System components / 4 3.5” HDD model
Illustrated parts catalog 20
Table 7 System Components Spare Parts List / 4 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
System board, Intel 5500 series processors
507255-001
Optional2
System board, Intel 5500 & 5600 series processors
608865-001
2
Power supplies (all support hot-plug)
Power supply 460 W
511777-001
Mandatory1
Power supply 750 W
511778-001
Mandatory1
Power supply 460 W 94%
599381-001
Mandatory1
Power supply 750 W 94%
599383-001
Mandatory1
3
DC Converter Power Backplane Assy.
519200-001
Mandatory1
4
System fans
519199-001
Mandatory1
5
Memory modules
DIMM, 2GB 2Rx8 PC3-10600R-9
501533-001
Mandatory1
DIMM, 4GB 2Rx4 PC3-10600R-9
501534-001
Mandatory1
DIMM, 4GB 4Rx8 PC3-8500R-7 LP
501535-001
Mandatory1
DIMM, 8GB 2Rx4 PC3-8500R-7
519201-001
Mandatory1
DIMM, 16GB 2RX4 PC3L-10600R-9
632204-001
Mandatory1
DIMM, 16GB 4RX4 PC3-8500R-7
501538-001
Mandatory1
DIMM, 1GB 1Rx8 PC3-10600E-9
501539-001
Mandatory1
DIMM, 2GB 2Rx8 PC3-10600E-9
501540-001
Mandatory1
PROC,Xeon E5620 4c, 2.4 Ghz, 12M, 80W
594887-001
Optional2
PROC,Xeon X5650 6c, 2.66 Ghz, 12M, 95W
594884-001
Optional2
PROC,Xeon X5660 6c, 2.8 Ghz, 12M, 95W
594883-001
Optional2
PROC,Xeon E5649 6c, 2.53GHz, 12M, 80W
628695-001
Optional2
PROC,Xeon E5645 6c, 2.4GHz, 12M, 80W
628696-001
Optional2
PROC,Xeon E5606 4c, 2.13GHz, 8M, 80W
628699-001
Optional2
Processor heat sinks
507247-001
Mandatory1
Registered DIMMs (RDIMMs)
Unregistered DIMMs (UDIMMs)
6
7
Processors, FCLGA 1366 Intel Xeon series
Illustrated parts catalog 21
Table 7 System Components Spare Parts List / 4 3.5” HDD Model
Item
Description
8
Optical disc drive (optional)
9
Spare Part
Number
Customer self
repair
SPS-DRV,ODD, SLIM SATA DVD-ROM
481428-001
Mandatory1
SPS-DRV,ODD, SLIM SATA DVD RW
481429-001
Mandatory1
72 GB 15,000 rpm
376594-001
Mandatory1
146 GB 15,000 rpm
376595-001
Mandatory1
300 GB 15,000 rpm
432146-001
Mandatory1
400 GB 10,000 rpm
456896-001
Mandatory1
450 GB 15,000 rpm
454274-001
Mandatory1
750 GB 7,200 rpm
461288-001
Mandatory1
1 TB 7,200 rpm
461289-001
Mandatory1
160 GB 7,200 rpm, 1.5Gbps
353043-001
Mandatory1
160 GB 7,200 rpm, 3.0Gbps
483095-001
Mandatory1
250 GB 7,200 rpm, 1.5Gbps
353044-001
Mandatory1
250 GB 7,200 rpm, 3.0Gbps
459318-001
Mandatory1
500 GB 7,200 rpm, 1.5Gbps
395501-001
Mandatory1
500 GB 7,200 rpm, 3.0Gbps
459319-001
Mandatory1
750 GB 7,200 rpm, 1.5Gbps
432401-001
Mandatory1
750 GB 7,200 rpm, 3.0Gbps
459320-001
Mandatory1
1 TB 7,200 rpm, 3.0Gbps
454273-001
Mandatory1
160 GB 7,200 rpm
459314-001
Mandatory1
250 GB 7,200 rpm
373313-001
Mandatory1
500 GB 7,200 rpm
404654-001
Mandatory1
750 GB 7,200 rpm
463047-001
Mandatory1
Hard drives
3.5” hot-plug SAS hard drives with carriers
3.5” hot-plug SATA hard drives with carriers
3.5”non- hot-plug SATA hard drives with carriers
Illustrated parts catalog 22
Table 7 System Components Spare Parts List / 4 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
10
Backplane four bays SAS/SATA hard drive
535348-001
Mandatory1
11
FH/FL PCI-E riser card
PCI-E x16+2PCI-X
507306-001
Mandatory1
3PCI-EX8
534235-001
Mandatory1
2PCI-EX8
516803-001
Mandatory1
PCI-E x16
534238-001
Mandatory1
PCI-E x16
507258-001
Mandatory1
13
TPM Module (Must be replaced with system board if present)
505836-001
Optional2
14
Dedicated Management Port Card
516806-001
Mandatory1
12
LP PCI-E riser card
Illustrated parts catalog 23
System components / 8 3.5” HDD model
Table 8 System Components Spare Parts List / 8 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
System board, Intel 5500 series processors
507255-001
Optional2
System board, Intel 5500 & 5600 series processors
608865-001
2
Power supplies (all support hot-plug)
Power supply 460 W
511777-001
Mandatory1
Power supply 750 W
511778-001
Mandatory1
Power supply 460 W 94%
599381-001
Mandatory1
Power supply 750 W 94%
599383-001
Mandatory1
3
DC Converter Power Backplane Assy.
519200-001
Mandatory1
4
System fans
519199-001
Mandatory1
5
Memory modules
DIMM, 2GB 2Rx8 PC3-10600R-9
501533-001
Mandatory1
DIMM, 4GB 2Rx4 PC3-10600R-9
501534-001
Mandatory1
DIMM, 4GB 4Rx8 PC3-8500R-7 LP
501535-001
Mandatory1
DIMM, 8GB 2Rx4 PC3-8500R-7
519201-001
Mandatory1
DIMM, 16GB 2RX4 PC3L-10600R-9
632204-001
Mandatory1
Registered DIMMs (RDIMMs)
Illustrated parts catalog 24
Table 8 System Components Spare Parts List / 8 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
DIMM, 16GB 4RX4 PC3-8500R-7
501538-001
Mandatory1
DIMM, 1GB 1Rx8 PC3-10600E-9
501539-001
Mandatory1
DIMM, 2GB 2Rx8 PC3-10600E-9
501540-001
Mandatory1
PROC,Xeon EP 2.93 Ghz, 8M, 95W
506012-001
Optional2
PROC,Xeon EP 2.67 Ghz, 8M, 95W
490070-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 80W
490073-001
Optional2
PROC,Xeon EP 2.0 Ghz, 4M, 80W QC
490074-001
Optional2
PROC,Xeon EP 2.53 Ghz, 8M, 80W
490071-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 60W
508567-001
Optional2
PROC,Xeon EP E5506 2.13 Ghz,4M, 80W
506013-001
Optional2
PROC,Xeon EP E5503 2.0 Ghz,4M, DC
594889-001
Optional2
PROC,Xeon L5630 4c, 2.13 Ghz, 12M, 40W
594891-001
Optional2
PROC,Xeon E5620 4c, 2.4 Ghz, 12M, 80W
594887-001
Optional2
PROC,Xeon X5650 6c, 2.66 Ghz, 12M, 95W
594884-001
Optional2
PROC,Xeon L5640 6c, 2.26 Ghz, 12M, 60W
594890-001
Optional2
PROC,Xeon E5630 4c, 2.53 Ghz, 12M, 80W
594886-001
Optional2
PROC,Xeon E5640 4c, 2.66 Ghz, 12M, 80W
594885-001
Optional2
PROC,Xeon X5660 6c, 2.8 Ghz, 12M, 95W
594883-001
Optional2
PROC,Xeon X5670 6c, 2.93 Ghz, 12M, 95W
594882-001
Optional2
PROC,Xeon X5675 6c, 3.06GHz, 12M, 95W
638134-001
Optional2
PROC,Xeon X5672 4c, 3.2GHz, 12M, 95W
638135-001
Optional2
PROC,Xeon E5649 6c, 2.53GHz, 12M, 80W
628695-001
Optional2
PROC,Xeon E5645 6c, 2.4GHz, 12M, 80W
628696-001
Optional2
PROC,Xeon E5606 4c, 2.13GHz, 8M, 80W
628699-001
Optional2
PROC,Xeon E5603 4c,1.6GHz, 4M, 80W
628700-001
Optional2
7
Processor heat sinks
507247-001
Mandatory1
8
Optical disc drive (optional)
SPS-DRV,ODD, SLIM SATA DVD-ROM
481428-001
Mandatory1
SPS-DRV,ODD, SLIM SATA DVD RW
481429-001
Mandatory1
Unregistered DIMMs (UDIMMs)
6
9
Processors, FCLGA 1366 Intel Xeon series
Hard drives
Illustrated parts catalog 25
Table 8 System Components Spare Parts List / 8 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
72 GB 15,000 rpm
376594-001
Mandatory1
146 GB 15,000 rpm
376595-001
Mandatory1
300 GB 15,000 rpm
432146-001
Mandatory1
400 GB 10,000 rpm
456896-001
Mandatory1
450 GB 15,000 rpm
454274-001
Mandatory1
750 GB 7,200 rpm
461288-001
Mandatory1
1 TB 7,200 rpm
461289-001
Mandatory1
160 GB 7,200 rpm, 1.5Gbps
353043-001
Mandatory1
160 GB 7,200 rpm, 3.0Gbps
483095-001
Mandatory1
250 GB 7,200 rpm, 1.5Gbps
353044-001
Mandatory1
250 GB 7,200 rpm, 3.0Gbps
459318-001
Mandatory1
500 GB 7,200 rpm, 1.5Gbps
395501-001
Mandatory1
500 GB 7,200 rpm, 3.0Gbps
459319-001
Mandatory1
750 GB 7,200 rpm, 1.5Gbps
432401-001
Mandatory1
750 GB 7,200 rpm, 3.0Gbps
459320-001
Mandatory1
1 TB 7,200 rpm, 3.0Gbps
454273-001
Mandatory1
160 GB 7,200 rpm
459314-001
Mandatory1
250 GB 7,200 rpm
373313-001
Mandatory1
500 GB 7,200 rpm
404654-001
Mandatory1
750 GB 7,200 rpm
463047-001
Mandatory1
10
Backplane eight bays SAS/SATA hard drive
507303-001
Mandatory1
11
FH/FL PCI-E riser card
507306-001
Mandatory1
2PCI-EX8
516803-001
Mandatory1
PCI-E x16
534238-001
Mandatory1
PCI-E x16
507258-001
Mandatory1
TPM Module (Must be replaced with system board if present)
505836-001
Optional2
3.5” hot-plug LFF SAS hard drives with carriers
3.5” hot-plug SATA hard drives with carriers
3.5”non- hot-plug SATA hard drives with carriers
PCI-E x16+2PCI-X
3PCI-EX8
12
13
LP PCI-E riser card
Illustrated parts catalog 26
Table 8 System Components Spare Parts List / 8 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
14
Dedicated Management Port Card
516806-001
Mandatory1
System components / 8 2.5” HDD model
Table 9 System Components Spare Parts List / 8 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
System board, Intel 5500 series processors
507255-001
Optional2
System board, Intel 5500 & 5600 series processors
608865-001
2
Power supplies (all support hot-plug)
Power supply 460 W
511777-001
Mandatory1
Power supply 750 W
511778-001
Mandatory1
Power supply 460 W 94%
599381-001
Mandatory1
Power supply 750 W 94%
599383-001
Mandatory1
3
DC Converter Power Backplane Assy.
519200-001
Mandatory1
4
System fans
519199-001
Mandatory1
5
Memory modules
501533-001
Mandatory1
Registered DIMMs (RDIMMs)
DIMM, 2GB 2Rx8 PC3-10600R-9
Illustrated parts catalog 27
Table 9 System Components Spare Parts List / 8 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
DIMM, 4GB 2Rx4 PC3-10600R-9
501534-001
Mandatory1
DIMM, 4GB 4Rx8 PC3-8500R-7 LP
501535-001
Mandatory1
DIMM, 8GB 2Rx4 PC3-8500R-7
519201-001
Mandatory1
DIMM, 16GB 2RX4 PC3 L-10600R-9
632204-001
Mandatory1
DIMM, 16GB 4RX4 PC3-8500R-7
501538-001
Mandatory1
DIMM, 1GB 1Rx8 PC3-10600E-9
501539-001
Mandatory1
DIMM, 2GB 2Rx8 PC3-10600E-9
501540-001
Mandatory1
PROC,Xeon EP 2.93 Ghz, 8M, 95W
506012-001
Optional2
PROC,Xeon EP 2.67 Ghz, 8M, 95W
490070-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 80W
490073-001
Optional2
PROC,Xeon EP 2.0 Ghz, 4M, 80W QC
490074-001
Optional2
PROC,Xeon EP 2.53 Ghz, 8M, 80W
490071-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 60W
508567-001
Optional2
PROC,Xeon EP E5506 2.13 Ghz,4M, 80W
506013-001
Optional2
PROC,Xeon EP E5503 2.0 Ghz,4M, DC
594889-001
Optional2
PROC,Xeon L5630 4c, 2.13 Ghz, 12M, 40W
594891-001
Optional2
PROC,Xeon E5620 4c, 2.4 Ghz, 12M, 80W
594887-001
Optional2
PROC,Xeon X5650 6c, 2.66 Ghz, 12M, 95W
594884-001
Optional2
PROC,Xeon L5640 6c, 2.26 Ghz, 12M, 60W
594890-001
Optional2
PROC,Xeon E5630 4c, 2.53 Ghz, 12M, 80W
594886-001
Optional2
PROC,Xeon E5640 4c, 2.66 Ghz, 12M, 80W
594885-001
Optional2
PROC,Xeon X5660 6c, 2.8 Ghz, 12M, 95W
594883-001
Optional2
PROC,Xeon X5670 6c, 2.93 Ghz, 12M, 95W
594882-001
Optional2
PROC,Xeon X5675 6c, 3.06GHz, 12M, 95W
638134-001
Optional2
PROC,Xeon X5672 4c, 3.2GHz, 12M, 95W
638135-001
Optional2
PROC,Xeon E5649 6c, 2.53GHz, 12M, 80W
628695-001
Optional2
PROC,Xeon E5645 6c, 2.4GHz, 12M, 80W
628696-001
Optional2
PROC,Xeon E5606 4c, 2.13GHz, 8M, 80W
628699-001
Optional2
PROC,Xeon E5603 4c,1.6GHz, 4M, 80W
628700-001
Optional2
Processor heat sinks
507247-001
Mandatory1
Unregistered DIMMs (UDIMMs)
6
7
Processors, FCLGA 1366 Intel Xeon series
Illustrated parts catalog 28
Table 9 System Components Spare Parts List / 8 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
8
Optical disc drive (optional)
SPS-DRV,ODD, SLIM SATA DVD-ROM
481428-001
Mandatory1
SPS-DRV,ODD, SLIM SATA DVD RW
481429-001
Mandatory1
36 GB 15,000 rpm DP
418397-001
Mandatory1
72 GB 10,000 rpm SP
376597-001
Mandatory1
72 GB 10,000 rpm DP
389346-001
Mandatory1
72 GB 15,000 rpm SP
432321-001
Mandatory1
72 GB 15,000 rpm DP
418398-001
Mandatory1
146 GB 10,000 rpm SP
432320-001
Mandatory1
146 GB 10,000 rpm DP
418399-001
Mandatory1
146 GB 15,000 rpm DP
504334-001
Mandatory1
300 GB 10,000 rpm DP
493083-001
Mandatory1
120 GB 5,400 rpm
459322-001
Mandatory1
250 GB 5,400 rpm
460426-001
Mandatory1
500 GB 5,400 rpm
508035-001
Mandatory1
10
Backplane eight bays SAS/SATA hard drive
532481-001
Mandatory1
11
FH/FL PCI-E riser card
507306-001
Mandatory1
2PCI-EX8FH
516803-001
Mandatory1
PCI-E x16
534238-001
Mandatory1
PCI-E x16
507258-001
Mandatory1
13
TPM Module (Must be replaced with system board if present)
505836-001
Optional2
14
Dedicated Management Port Card
516806-001
Mandatory1
9
Hard drives
2.5” hot-plug SAS hard drives with carriers
2.5” hot-plug SATA hard drives with carriers
PCI-E x16+2PCI-X FH
3PCI-EX8
12
LP PCI-E riser card
Illustrated parts catalog 29
System components / 12 3.5” HDD model
Table 10 System Components Spare Parts List / 12 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
System board, Intel 5500 series processors
507255-001
Optional2
System board, Intel 5500 & 5600 series processors
608865-001
2
Power supplies (all support hot-plug)
Power supply 460 W
511777-001
Mandatory1
Power supply 750 W
511778-001
Mandatory1
Power supply 460 W 94%
599381-001
Mandatory1
Power supply 750 W 94%
599383-001
Mandatory1
3
DC Converter Power Backplane Assy.
519200-001
Mandatory1
4
System fans
519199-001
Mandatory1
5
Memory modules
DIMM, 2GB 2Rx8 PC3-10600R-9
501533-001
Mandatory1
DIMM, 4GB 2Rx4 PC3-10600R-9
501534-001
Mandatory1
DIMM, 4GB 4Rx8 PC3-8500R-7 LP
501535-001
Mandatory1
DIMM, 8GB 2Rx4 PC3-8500R-7
519201-001
Mandatory1
DIMM, 16GB 2RX4 PC3 L-10600R-9
632204-001
Mandatory1
Registered DIMMs (RDIMMs)
Illustrated parts catalog 30
Table 10 System Components Spare Parts List / 12 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
DIMM, 16GB 4RX4 PC3-8500R-7
501538-001
Mandatory1
DIMM, 1GB 1Rx8 PC3-10600E-9
501539-001
Mandatory1
DIMM, 2GB 2Rx8 PC3-10600E-9
501540-001
Mandatory1
PROC,Xeon EP 2.93 Ghz, 8M, 95W
506012-001
Optional2
PROC,Xeon EP 2.67 Ghz, 8M, 95W
490070-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 80W
490073-001
Optional2
PROC,Xeon EP 2.0 Ghz, 4M, 80W QC
490074-001
Optional2
PROC,Xeon EP 2.53 Ghz, 8M, 80W
490071-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 60W
508567-001
Optional2
PROC,Xeon EP E5506 2.13 Ghz,4M, 80W
506013-001
Optional2
PROC,Xeon EP E5503 2.0 Ghz,4M, DC
594889-001
Optional2
PROC,Xeon L5630 4c, 2.13 Ghz, 12M, 40W
594891-001
Optional2
PROC,Xeon E5620 4c, 2.4 Ghz, 12M, 80W
594887-001
Optional2
PROC,Xeon X5650 6c, 2.66 Ghz, 12M, 95W
594884-001
Optional2
PROC,Xeon L5640 6c, 2.26 Ghz, 12M, 60W
594890-001
Optional2
PROC,Xeon E5630 4c, 2.53 Ghz, 12M, 80W
594886-001
Optional2
PROC,Xeon E5640 4c, 2.66 Ghz, 12M, 80W
594885-001
Optional2
PROC,Xeon X5660 6c, 2.8 Ghz, 12M, 95W
594883-001
Optional2
PROC,Xeon X5670 6c, 2.93 Ghz, 12M, 95W
594882-001
Optional2
PROC,Xeon X5675 6c, 3.06GHz, 12M, 95W
638134-001
Optional2
PROC,Xeon X5672 4c, 3.2GHz, 12M, 95W
638135-001
Optional2
PROC,Xeon E5649 6c, 2.53GHz, 12M, 80W
628695-001
Optional2
PROC,Xeon E5645 6c, 2.4GHz, 12M, 80W
628696-001
Optional2
PROC,Xeon E5606 4c, 2.13GHz, 8M, 80W
628699-001
Optional2
PROC,Xeon E5603 4c,1.6GHz, 4M, 80W
628700-001
Optional2
7
Processor heat sinks
507247-001
Mandatory1
8
Hard drives
72 GB 15,000 rpm
376594-001
Mandatory1
146 GB 15,000 rpm
376595-001
Mandatory1
Unregistered DIMMs (UDIMMs)
6
Processors, FCLGA 1366 Intel Xeon series
3.5” hot-plug SAS hard drives with carriers
Illustrated parts catalog 31
Table 10 System Components Spare Parts List / 12 3.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
300 GB 15,000 rpm
432146-001
Mandatory1
400 GB 10,000 rpm
456896-001
Mandatory1
450 GB 15,000 rpm
454274-001
Mandatory1
750 GB 7,200 rpm
461288-001
Mandatory1
1 TB 7,200 rpm
461289-001
Mandatory1
160 GB 7,200 rpm, 1.5Gbps
353043-001
Mandatory1
160 GB 7,200 rpm, 3.0Gbps
483095-001
Mandatory1
250 GB 7,200 rpm, 1.5Gbps
353044-001
Mandatory1
250 GB 7,200 rpm, 3.0Gbps
459318-001
Mandatory1
500 GB 7,200 rpm, 1.5Gbps
395501-001
Mandatory1
500 GB 7,200 rpm, 3.0Gbps
459319-001
Mandatory1
750 GB 7,200 rpm, 1.5Gbps
432401-001
Mandatory1
750 GB 7,200 rpm, 3.0Gbps
459320-001
Mandatory1
1 TB 7,200 rpm, 3.0Gbps
454273-001
Mandatory1
160 GB 7,200 rpm
459314-001
Mandatory1
250 GB 7,200 rpm
373313-001
Mandatory1
500 GB 7,200 rpm
404654-001
Mandatory1
750 GB 7,200 rpm
463047-001
Mandatory1
9
Backplane twelve bays SAS/SATA hard drive
507304-001
Mandatory1
10
FH/FL PCI-E riser card
507306-001
Mandatory1
2PCI-EX8
516803-001
Mandatory1
PCI-E x16
534238-001
Mandatory1
PCI-E x16
507258-001
Mandatory1
12
TPM Module (Must be replaced with system board if present)
505836-001
Optional2
13
Dedicated Management Port Card
516806-001
Mandatory1
3.5” hot-plug SATA hard drives with carriers
3.5”non- hot-plug SATA hard drives with carriers
PCI-E x16+2PCI-X
3PCI-EX8
11
LP PCI-E riser card
Illustrated parts catalog 32
System components /25 2.5” HDD model
Table 11 System Components Spare Parts List / 25 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
1
System board, Intel 5500 series processors
507255-001
Optiona2
System board, Intel 5500 & 5600 series processors
608865-001
2
Power supplies (all support hot-plug)
Power supply 460 W
511777-001
Mandatory1
Power supply 750 W
511778-001
Mandatory1
Power supply 460 W 94%
599381-001
Mandatory1
Power supply 750 W 94%
599383-001
Mandatory1
3
DC Converter Power Backplane Assy.
519200-001
Mandatory1
4
System fans
519199-001
Mandatory1
5
Memory modules
DIMM, 2GB 2Rx8 PC3-10600R-9
501533-001
Mandatory1
DIMM, 4GB 2Rx4 PC3-10600R-9
501534-001
Mandatory1
DIMM, 4GB 4Rx8 PC3-8500R-7 LP
501535-001
Mandatory1
DIMM, 8GB 2Rx4 PC3-8500R-7
519201-001
Mandatory1
Registered DIMMs (RDIMMs)
Illustrated parts catalog 33
Table 11 System Components Spare Parts List / 25 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
DIMM, 16GB 2RX4 PC3L-10600R-9
632204-001
Mandatory1
DIMM, 16GB 4RX4 PC3-8500R-7
501538-001
Mandatory1
DIMM, 1GB 1Rx8 PC3-10600E-9
501539-001
Mandatory1
DIMM, 2GB 2Rx8 PC3-10600E-9
501540-001
Mandatory1
PROC,Xeon EP 2.93 Ghz, 8M, 95W
506012-001
Optional2
PROC,Xeon EP 2.67 Ghz, 8M, 95W
490070-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 80W
490073-001
Optional2
PROC,Xeon EP 2.0 Ghz, 4M, 80W QC
490074-001
Optional2
PROC,Xeon EP 2.53 Ghz, 8M, 80W
490071-001
Optional2
PROC,Xeon EP 2.26 Ghz, 8M, 60W
508567-001
Optional2
PROC,Xeon EP E5506 2.13 Ghz,4M, 80W
506013-001
Optional2
PROC,Xeon EP E5503 2.0 Ghz,4M, DC
594889-001
Optional2
PROC,Xeon L5630 4c, 2.13 Ghz, 12M, 40W
594891-001
Optional2
PROC,Xeon E5620 4c, 2.4 Ghz, 12M, 80W
594887-001
Optional2
PROC,Xeon X5650 6c, 2.66 Ghz, 12M, 95W
594884-001
Optional2
PROC,Xeon L5640 6c, 2.26 Ghz, 12M, 60W
594890-001
Optional2
PROC,Xeon E5630 4c, 2.53 Ghz, 12M, 80W
594886-001
Optional2
PROC,Xeon E5640 4c, 2.66 Ghz, 12M, 80W
594885-001
Optional2
PROC,Xeon X5660 6c, 2.8 Ghz, 12M, 95W
594883-001
Optional2
PROC,Xeon X5670 6c, 2.93 Ghz, 12M, 95W
594882-001
Optional2
PROC,Xeon X5675 6c, 3.06GHz, 12M, 95W
638134-001
Optional2
PROC,Xeon X5672 4c, 3.2GHz, 12M, 95W
638135-001
Optional2
PROC,Xeon E5649 6c, 2.53GHz, 12M, 80W
628695-001
Optional2
PROC,Xeon E5645 6c, 2.4GHz, 12M, 80W
628696-001
Optional2
PROC,Xeon E5606 4c, 2.13GHz, 8M, 80W
628699-001
Optional2
PROC,Xeon E5603 4c,1.6GHz, 4M, 80W
628700-001
Optional2
7
Processor heat sinks
507247-001
Mandatory1
8
Hard drives
418397-001
Mandatory1
Unregistered DIMMs (UDIMMs)
6
Processors, FCLGA 1366 Intel Xeon series
2.5” hot-plug SAS hard drives with carriers
36 GB 15,000 rpm DP
Illustrated parts catalog 34
Table 11 System Components Spare Parts List / 25 2.5” HDD Model
Item
Description
Spare Part
Number
Customer self
repair
72 GB 10,000 rpm SP
376597-001
Mandatory1
72 GB 10,000 rpm DP
389346-001
Mandatory1
72 GB 15,000 rpm SP
432321-001
Mandatory1
72 GB 15,000 rpm DP
418398-001
Mandatory1
146 GB 10,000 rpm SP
432320-001
Mandatory1
146 GB 10,000 rpm DP
418399-001
Mandatory1
146 GB 15,000 rpm DP
504334-001
Mandatory1
300 GB 10,000 rpm DP
493083-001
Mandatory1
120 GB 5,400 rpm
459322-001
Mandatory1
250 GB 5,400 rpm
460426-001
Mandatory1
500 GB 5,400 rpm
508035-001
Mandatory1
9
Backplane twenty-five bays SAS/SATA hard drive
516809-001
Mandatory1
10
FH/FL PCIe riser card
507306-001
Mandatory1
2PCI-EX8
516803-001
Mandatory1
PCI-E x16
534238-001
Mandatory1
PCI-E x16
507258-001
Mandatory1
12
TPM Module (Must be replaced with system board if present)
505836-001
Optional2
13
Dedicated Management Port Card
516806-001
Mandatory1
2.5” hot-plug SATA hard drives with carriers
PCI-E x16+2PCI-X
3PCI-EX8
11
LP PCIe riser card
Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these
parts, you will be charged for the travel and labor costs of this service.
1
Optional—Parts for which customer self repair is optional. These parts are also designed for
customer self repair. If, however, you require that HP replace them for you, there may or may not be
additional charges, depending on the type of warranty service designated for your product.
2
No—Some HP parts are not designed for customer self repair. In order to satisfy the customer
warranty, HP requires that an authorized service provider replace the part. These parts are identified
as "No" in the Illustrated Parts Catalog.
3
Illustrated parts catalog 35
Mandatory: Obligatoire—Pièces pour lesquelles la réparation par le client est obligatoire. Si vous
demandez à HP de remplacer ces pièces, les coûts de déplacement et main d'œuvre du service vous
seront facturés.
1
Optional: Facultatif—Pièces pour lesquelles la réparation par le client est facultative. Ces pièces sont
également conçues pour permettre au client d'effectuer lui-même la réparation. Toutefois, si vous
demandez à HP de remplacer ces pièces, l'intervention peut ou non vous être facturée, selon le type
de garantie applicable à votre produit.
2
No: Non—Certaines pièces HP ne sont pas conçues pour permettre au client d'effectuer lui-même la
réparation. Pour que la garantie puisse s'appliquer, HP exige que le remplacement de la pièce soit
effectué par un Mainteneur Agréé. Ces pièces sont identifiées par la mention “Non” dans le
Catalogue illustré.
3
Mandatory: Obbligatorie—Parti che devono essere necessariamente riparate dal cliente. Se il cliente
ne affida la riparazione ad HP, deve sostenere le spese di spedizione e di manodopera per il
servizio.
1
Optional: Opzionali—Parti la cui riparazione da parte del cliente è facoltativa. Si tratta comunque
di componenti progettati per questo scopo. Se tuttavia il cliente ne richiede la sostituzione ad HP,
potrebbe dover sostenere spese addizionali a seconda del tipo di garanzia previsto per il prodotto.
2
No: Non CSR—Alcuni componenti HP non sono progettati per la riparazione da parte del cliente.
Per rispettare la garanzia, HP richiede che queste parti siano sostituite da un centro di assistenza
autorizzato. Tali parti sono identificate da un “No” nel Catalogo illustrato dei componenti.
3
Mandatory: Zwingend—Teile, die im Rahmen des Customer Self Repair Programms ersetzt werden
müssen. Wenn Sie diese Teile von HP ersetzen lassen, werden Ihnen die Versand-und Arbeitskosten
für diesen Service berechnet.
1
Optional: Optional—Teile, für die das Customer Self Repair-Verfahren optional ist. Diese Teile sind
auch für Customer Self Repair ausgelegt. Wenn Sie jedoch den Austausch dieser Teile von HP
vornehmen lassen möchten, können bei diesem Service je nach den für Ihr Produkt vorgesehenen
Garantiebedingungen zusätzliche Kosten anfallen.
2
No: Kein—Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des
Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten
Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet.
3
Mandatory: Obligatorio—componentes para los que la reparación por parte del usuario es
obligatoria. Si solicita a HP que realice la sustitución de estos componentes, tendrá que hacerse
cargo de los gastos de desplazamiento y de mano de obra de dicho servicio.
1
Optional: Opcional—componentes para los que la reparación por parte del usuario es opcional.
Estos componentes también están diseñados para que puedan ser reparados por el usuario. Sin
embargo, si precisa que HP realice su sustitución, puede o no conllevar costes adicionales,
dependiendo del tipo de servicio de garantía correspondiente al producto.
2
No: No—Algunos componentes no están diseñados para que puedan ser reparados por el usuario.
Para que el usuario haga valer su garantía, HP pone como condición que un proveedor de servicios
autorizado realice la sustitución de estos componentes. Dichos componentes se identifican con la
palabra “No” en el catálogo ilustrado de componentes.
3
Illustrated parts catalog 36
Mandatory: Verplicht—Onderdelen waarvoor Customer Self Repair verplicht is. Als u HP verzoekt
deze onderdelen te vervangen, komen de reiskosten en het arbeidsloon voor uw rekening.
1
Optional: Optioneel—Onderdelen waarvoor reparatie door de klant optioneel is. Ook deze
onderdelen zijn ontworpen voor reparatie door de klant. Als u echter HP verzoekt deze onderdelen
voor u te vervangen, kunnen daarvoor extra kosten in rekening worden gebracht, afhankelijk van het
type garantieservice voor het product.
2
No: Nee—Sommige HP onderdelen zijn niet ontwikkeld voor reparatie door de klant. In verband
met de garantievoorwaarden moet het onderdeel door een geautoriseerde Service Partner worden
vervangen. Deze onderdelen worden in de geïllustreerde onderdelencatalogus aangemerkt met
"Nee".
3
Mandatory: Obrigatória—Peças cujo reparo feito pelo cliente é obrigatório. Se desejar que a HP
substitua essas peças, serão cobradas as despesas de transporte e mão-de-obra do serviço.
1
Optional: Opcional—Peças cujo reparo feito pelo cliente é opcional. Essas peças também são
projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode
haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado
ao produto.
2
No: Nenhuma—Algumas peças da HP não são projetadas para o reparo feito pelo cliente. A fim de
cumprir a garantia do cliente, a HP exige que um técnico autorizado substitua a peça. Essas peças
estão identificadas com a marca “No” (Não), no catálogo de peças ilustrado.
3
HP contact information
For the name of the nearest HP authorized reseller:
•
•
•
In the United States, call 1-800-345-1518.
In Canada, call 1-800-263-5868.
In other locations, refer to the HP website at http://www.hp.com/.
For HP technical support:
•
In North America:
○ Call 1-800-HP-INVENT (1-800-474-6836). This service is available 24 hours a day, 7 days
a week. For continuous quality improvement, calls may be recorded or monitored.
○ If you have purchased a Care Pack (service upgrade), call 1-800-633-3600. For more
information about Care Packs, refer to the HP website at http://www.hp.com/.
•
Outside North America, call the nearest HP Technical Support Phone Center. For telephone
numbers for worldwide Technical Support Centers, refer to the HP website at
http://www.hp.com/.
Before you contact HP
Be sure to have the following information available before you call HP:
•
•
•
Technical support registration number (if applicable)
Product serial number
Product model name and number
Illustrated parts catalog 37
•
•
•
•
Applicable error messages
Add-on boards or hardware model number and serial number
Third-party hardware or software model number
Operating system type and revision level
Illustrated parts catalog 38
Removal and replacement procedures
This chapter provides subassembly/module-level removal and replacement procedures for the HP
ProLiant DL288 G6 server.
Review the specifications of a new component before installing it to make sure it is compatible with
the server. When you integrate new components into the system, record its model and serial number,
and any other pertinent information for future reference. After completing any removal or replacement
procedure, run the diagnostics program to verify that all components operate properly.
NOTE: The figures used in this chapter to illustrate procedural steps are labeled numerically (i.e., 1,
2…). When these figures are used in substep items, the alphabetically labeled instructions
correspond to the numbered labels on the related figure (i.e., label 1 corresponds to step a, label 2
corresponds to step b, etc.). The procedures described in this section assume that the server is out of
the rack and is positioned on a flat, stable surface.
Hardware configuration tools
You will need the following tools:
•
T-10/T-15 wrench
The following references and software tools will assist with the hardware configuration:
•
•
•
HP ProLiant DL288 G6 Server Easy set-up CD
IPMI Event Log
Diagnostics Utility Software
Hardware configuration information
Electrostatic discharge information
An electrostatic discharge (ESD) can damage static-sensitive devices or micro circuitry. Proper
packaging and grounding techniques are necessary precautions to prevent damage. To prevent
electrostatic damage, observe the following precautions:
•
•
•
Transport products in static-safe containers such as conductive tubes, bags, or boxes.
•
Keep work area free of nonconductive materials, such as ordinary plastic assembly aids and
foam packing.
•
Make sure that you are always properly grounded (earthed) when touching a static-sensitive
component or assembly.
•
•
•
Avoid touching pins, leads, or circuitry.
Keep electrostatic-sensitive parts in their containers until they arrive at static-free stations.
Cover workstations with approved static-dissipating material. Use a wrist strap connected to the
work surface, and properly grounded (earthed) tools and equipment.
Always place drives with the Printed Circuit Board (PCB) assembly-side down.
Use conductive field service tools.
Removal and replacement procedures 39
Pre-installation procedure
Perform the steps below before you open the server or before you remove or replace any component.
WARNING: Failure to properly turn off the server before you open the server or before your start
installing and removing components may cause serious damage as well as bodily harm.
1.
Turn off the server and all the peripherals connected to it.
2.
Unplug all cables from the power outlet(s) to avoid exposure to high energy levels that may
cause burns when parts are short-circuited by metal objects such as tools or jewelry.
3.
If necessary, label each one to expedite reassembly.
4.
Disconnect telecommunication cables to avoid exposure to shock hazard from ringing voltages.
5.
If server is installed in a rack, remove server and place it on a flat surface.
6.
Remove the top cover according to the instructions described in the “System cover” section in this
chapter.
7.
Follow the ESD precautions listed previously in this chapter when handling a server component.
IMPORTANT: To streamline the configuration process, read through the entire installation and
removal procedures first and make sure you understand them before you begin.
Post-installation instructions
Observe the following items after installing or removing a server component:
1.
Be sure all components are installed according to the described step-by-step instructions.
2.
Reinstall the rear cage, air baffle, peripherals, and system cables that you have removed.
3.
Reinstall the top cover.
4.
Reinstall server into rack.
5.
Connect all external cables and the AC power cord(s) to the system.
6.
Press the power button on the front panel to turn on the server.
Server warnings and cautions
Before installing a server, be sure that you understand the following warnings and cautions.
WARNING: To reduce the risk of electric shock or damage to the equipment:
• Do not disable the power cord grounding plug. The grounding plug is an important safety
feature.
• Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all
times.
• Unplug the power cord from the power supply to disconnect power to the equipment.
• Do not route the power cord where it can be walked on or pinched by items placed against it.
Pay particular attention to the plug, electrical outlet, and the point where the cord extends from
the server.
WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal
system components to cool before touching them.
Removal and replacement procedures 40
CAUTION: Do not operate the server for long periods with the system cover open or removed.
Operating the server in this manner results in improper airflow and improper cooling that can lead
to thermal damage.
HP Trusted Platform Module
The TPM is not a customer-removable part.
CAUTION: Any attempt to remove an installed TPM from the system board breaks or disfigures the
TPM security rivet. Upon locating a broken or disfigured rivet on an installed TPM, administrators
should consider the system compromised and take appropriate measures to ensure the integrity of
the system data.
IMPORTANT: If you suspect a TPM board failure, leave the TPM installed and remove the system.
Contact an HP authorized service provider for a replacement system board and TPM board.
Symbols on equipment
The following symbols may be placed on equipment to indicate the presence of potentially hazardous
conditions.
This symbol indicates the presence of hazardous energy circuits or electric shock
hazards. Refer all servicing to qualified personnel.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure. Refer all maintenance, upgrades, and servicing to qualified personnel.
This symbol indicates the presence of electric shock hazards. The area contains no
user or field serviceable parts. Do not open for any reason.
WARNING: To reduce the risk of injury from electric shock hazards, do not open this
enclosure.
This symbol on an RJ-45 receptacle indicates a network interface connection.
WARNING: To reduce the risk of electric shock, fire, or damage to the equipment, do
not plug telephone or telecommunications connectors into this receptacle.
This symbol indicates the presence of a hot surface or hot component. If this surface is
contacted, the potential for injury exists.
WARNING: To reduce the risk of injury from a hot component, allow the surface to
cool before touching.
Weight in kg.
Weight in lb.
This symbol indicates that the component exceeds the recommended weight for one
individual to handle safely.
WARNING: To reduce the risk of personal injury or damage to the equipment,
observe local occupational health and safety requirements and guidelines for manual
material handling.
Removal and replacement procedures 41
These symbols, on power supplies or systems, indicate that the equipment is supplied
by multiple sources of power.
WARNING: To reduce the risk of injury from electric shock, remove all power cords
to completely disconnect power from the system.
Powering down the server
The server does not completely power down when the power button on the front panel is pressed. The
button toggles between On and Standby. The standby position removes power from most electronics
and the drives, but some internal circuitry remains active. To completely remove all power from the
system, disconnect all power cords from the server.
To power down the server:
1.
Shut down the server as directed by the operating system documentation.
2.
Press the power button to toggle to Standby.
3.
This places the server in standby mode changing the power LED indicator to amber. In this
mode, the main power supply output is disabled. Standby does not completely disable or
remove power from the system.
4.
Disconnect the AC power cord(s) from the power outlet(s) and then from the server.
5.
Be sure that the power LED indicator is turned off and that the fan noise has stopped.
6.
Disconnect all peripheral devices from the server.
Removal and replacement procedures 42
System cover
You need to remove the top cover before you can remove or replace a server component. The top
cover needs to be removed to service the SAS/SATA backplane.
Top cover
To remove the top cover:
1.
Loosen the screw on the top cover with a T-10 wrench.
2.
Press the latch on the top cover.
3.
Slide the cover toward the rear of the server and then lift the top cover to remove it from the
chassis. Lift the top cover away from the chassis.
Figure 1 Removing the Top Cover
To reinstall the top cover:
1.
Align the top cover to the chassis and then slide it towards the front panel to position it into
place.
2.
Once the cover is attached to the chassis, tighten the screw on the top cover with a T-10 wrench.
Removal and replacement procedures 43
Figure 2 Reinstalling the Top Cover
Drives
The server supports the following configurations:
• 4 drive bays for 3.5 in. hard disk drives and 1 drive bay for optical disc drive
• 8 drive bays for 3.5 in. hard disk drives and 1 drive bay for optical disc drive
• 8 drive bays for 2.5 in. hard disk drives and 1 drive bay for optical disc drive
•12 drive bays for 3.5 in. hard disk drives (14 drive bays with optional rear two drive kit)
• 25 drive bays for 2.5 in. hard disk drives
Cable management
Always follow good cable management practices when working inside the computer.
board.
•
•
Keep cables away from major heat sources like the heat sink.
•
•
Keep cables clear of sliding or moveable parts to prevent cutting or crimping.
•
•
•
•
•
Some flat ribbon cables come pre-folded. Never change the folds on these cables.
Do not jam cables on top of expansion cards or memory modules. Printed circuit cards are not
designed to withstand excessive pressure.
When folding a flat ribbon cable, never fold to a sharp crease. Sharp creases may damage the
wires.
Do not sharply bend any cable. A sharp bend can break the internal wires.
Never bend a SATA data cable tighter than a 30 mm (1.18 in.) radius.
Never crease a SATA data cable.
Do not rely on components like the drive cage, power supply, or system cover to push cables
down into the chassis.
The next steps illustrate the removal of power cable from connector J60, 51, and 64 on system
Removal and replacement procedures 44
1.
Squeeze on the top of the retaining latch attached to the cable end of the connector.
2.
Grasp the cable end of the connector and pull it straight up.
CAUTION: Always pull the connector—NEVER pull on the cable. Pulling on the cable could damage
the cable and result in a failed power supply.
Figure 3 Unplugging Power Cable
Cable connections
The following tables provide information about switching power supply cable connector labels.
Table 12 Cable Connections from the 460/750 W Power Supply
Cable
To
Cable designator
Switching power supply
System board 24-pin power connector
P1
Switching power supply
System board 8-pin power connector
P2
Switching power supply
System board 4-pin power connector
P3
Switching power supply
System board power supply EFF
connector
RPS
Switching power supply
Front optical disk drive or rear optical
disk drive
CD
Switching power supply
4/8 HDD backplane
P4
Switching power supply
12/25 HDD backplane without 2HDD
backplane
P4 and P5
Switching power supply
12 HDD backplane and 2 HDD
backplane
P5 extended connectors, the two
short cable connectors to 12HDD
backplane, the long cable
connector to 2HDD backplane
Removal and replacement procedures 45
The following tables provide the system board designators that various cables plug into. For more
detailed information about system board components, see “System board components”.
Table 13 Cable Connections from the System Board
Cable
To
System board designator
20-Pin front panel connector
Front panel
J42
USB 0/1 connector
Front panel USB 2.0
J53
USB 4 connector
Internal USB 2.0
J69
24-pin power connector
Power supply
J51
8-pin power connector
Power supply
J64
4-pin power connector
Power supply
J60
3-pin backplane I2C connector
Backplane
J65
12-pin power supply EFF connector
Power supply
J79
16-pin Power backplane control connector
Power supply RPS
J76
10-pin Hard drive backplane SGPIO
connector
2 HDD backplane on the HDD PCI
cage
J66
6-pin system fan 1 connector
System fan 1 (four system fans)
J63
or system fan 1/2 (eight system fans)
6-pin system fan 2 connector
System fan 2 (four system fans)
J71
or system fan 3/4 (eight system fans)
6-pin system fan 3 connector
System fan 3 (four system fans)
J62
System fan 5/6 (eight system fans)
6-pin system fan 5 connector
System fan 4 (four system fans)
J68
or system fan 7/8 (eight system fans)
LCD connector (optional)
Optional LCD module
J56
Table 14 Drive Cable Connections / 4 3.5” HDD Model
Cable
To
SATA&SAS connector
designator
SATAs 1 to 4
4 3.5” HDD Backplane
Table 15 Drive Cable Connections / 8 3.5” HDD Model
Cable
To
SATA&SAS connector
designator
PCI storage controller card (LP)
8 3.5” HDD Backplane
3rd party Mini-SAS
connector
PCI storage controller card (LP)
8 3.5” HDD Backplane
3rd party Mini-SAS
connector
Removal and replacement procedures 46
Table 15 Drive Cable Connections / 8 3.5” HDD Model
Cable
To
SATA&SAS connector
designator
SATA 5 connector (optional)
Optical disk drive on the front
panel
J57
Table 16 Drive Cable Connections / 8 2.5” HDD Model
Cable
To
SATA&SAS connector
designator
PCI storage controller card
8 2.5” HDD Backplane
3rd party Mini-SAS
connector 1
PCI storage controller card
8 2.5” HDD Backplane
3rd party Mini-SAS
connector 2
SATA 5 connector (optional)
Optical disk drive on the front
panel
J57
Table 17 Drive Cable Connections / 12 3.5” HDD Model with Optical Disc Drive PCI Cages
Cable
To
SATA&SAS connector
designator
PCI storage controller card (FH/FL)
12 3.5” HDD Backplane
3rd party Mini-SAS
connector
SATA 5 connector
Rear optical disk drive on the
ODD PCI cage
J57
Table 18 Drive Cable Connections / 12 3.5” HDD Model with HDD PCI Cages
Cable
To
SATA&SAS connector
designator
PCI storage controller card (LP)
12 3.5” HDD backplane
3rd party Mini-SAS
connector
HDD connector 13 on 12 3.5” HDD backplane
2 HDD backplane on the HDD
PCI cages
J3
HDD connector 14 on 12 3.5” HDD backplane
2 HDD backplane on the HDD
PCI cages
J2
HDD LED connector on the 12 3.5” HDD
backplane
2 HDD backplane
J10
Table 19 Drive Cable Connections / 25 2.5” HDD Model
Cable
To
SATA&SAS connector
designator
Removal and replacement procedures 47
Table 19 Drive Cable Connections / 25 2.5” HDD Model
Cable
To
SATA&SAS connector
designator
PCI storage controller card
25 2.5” HDD Backplane
3rd party Mini-SAS
connector 1
PCI storage controller card
25 2.5” HDD Backplane
3rd party Mini-SAS
connector 2
Removal and replacement procedures 48
Drive bay configuration
The server supports a maximum of twenty-five 2.5 in. hard disk drive bays.
Figure 4 System Drive Bays / 4 3.5” HDD Model
Item
Description
1
Optical disc drive bay (optional)
2
3.5 in. hard disk drive bays (4)
Removal and replacement procedures 49
Figure 5 System Drive Bays / 8 3.5” HDD Model
Item
Description
1
Optical disc drive bay (optional)
2
3.5 in. hard disk drive bays (8)
Figure 6 System Drive Bays / 8 2.5” HDD Model
Item
Description
1
Optical disc drive bay (optional)
2
2.5 in. hard disk drive bays (8)
Removal and replacement procedures 50
Figure 7 System Drive Bays / 12 3.5” HDD Model
Item
Description
1
3.5 in. hard disk drive bays (12)
Figure 8 System Drive Bays / 25 2.5” HDD Model
Item
Description
1
2.5 in. hard disk drive bays (25)
Removal and replacement procedures 51
Optical disc drive bay
The Optical disc drive bay of servers with 8 3.5-inch HDDs, 8 2.5-inch HDDs and 12 3.5-inch HDDs
support the optional installation of a 12.7 mm (0.5 in.) optical disc drive, so the following procedure
is for servers with 8 3.5-inch HDDs.
To remove the optical disc drive:
1.
Remove the top cover.
2.
Unplug the SATA and power cables.
3.
Loosen the screws.
Figure 9 Removing the Cables and Screws
4.
Push the optical disc drive toward the front of the unit.
5.
Pull the optical disc drive out of the chassis.
Figure 10 Removing the Optical disc drive
Removal and replacement procedures 52
IMPORTANT: If you remove an optical disc drive without plans of installing a new one, you must
reinstall the blank to maintain proper system airflow.
To remove the bezel blank:
1.
Poke the hook of the bezel blank with a T-10/15 wrench through the round hole on the top side
of the HDD cage.
2.
Pull the bezel blank out of the bezel.
CAUTION: Do not discard the bezel blank. If the optical disc drive is removed in the future, you must
reinstall the bezel blank to maintain proper system function.
Figure 11 Removing the Bezel Blank
Removal and replacement procedures 53
To install the optical disc drive:
1.
Slide the optical disc drive into the chassis.
2.
Secure the optical disc drive to the chassis with the two screws.
3.
Connect the SATA and power cables to their corresponding connectors on the optical disc drive.
Figure 12 Installing the Optical disc drive
Removal and replacement procedures 54
Hard drives
The drive bays on the front panel can accommodate up to twenty-five 2.5-inch hard drives. You can
install either SAS hard drives or SATA hard drives in the server.
For servers with 4 3.5-inch HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 4, from left to right, when viewed from the front of the server.
Figure 13 Hard Drive Configuration / 4 3.5” HDD Model
Item
Description
1-4
SAS/SATA hard drives 1-4
Removal and replacement procedures 55
For servers with 8 3.5-inch HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 8, from top to bottom, left to right, when viewed from the front of the server.
Figure 14 Hard Drive Configuration / 8 3.5” HDD Model
Item
Description
1-8
SAS/SATA hard drives 1-8
Removal and replacement procedures 56
For servers with 8 2.5-inch HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 8, from top to bottom, left to right, when viewed from the front of the server.
Figure 15 Hard Drive Configuration / 8 2.5” HDD Model
Item
Description
1-8
SAS/SATA hard drives 1-8
Removal and replacement procedures 57
For servers with 12 3.5-inch HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 12, from top to bottom, left to right, when viewed from the front of the server.
Figure 16 Hard Drive Configuration / 12 3.5” HDD Model
Item
Description
1-12
SAS/SATA hard drives 1-12
Removal and replacement procedures 58
For servers with 25 2.5-inch HDDs, the hard drives installed in the server are labeled from Device 1 to
Device 25, from top to bottom, left to right, when viewed from the front of the server.
Figure 17 Hard Drive Configuration / 25 2.5” HDD Model
Item
Description
1-25
SAS/SATA hard drives 1-25
Removal and replacement procedures 59
To remove the hard drive:
1.
Press the hard disk carrier button to release the ejector lever.
2.
Use the HDD carrier latch to pull the drive out of the cage.
Make sure to support the drive when pulling it out of the cage.
3.
Pull the hard drive assembly out of the drive bay.
Figure 18 Removing the Hard Drive
To install the hard drive:
1.
Pull the hard drive blank out of the chassis.
Figure 19 Removing the Hard Drive Blank
IMPORTANT: Do not discard the hard drive blank. If the drive is removed in the future, you must
reinstall the hard drive blank to maintain proper system airflow.
Removal and replacement procedures 60
2.
Push the hard drive assembly into the drive bay until it stops.
3.
Press the HDD carrier latch inward until it clicks.
Figure 20 Installing the Hard Drive
SAS/SATA HDD backplane
The following figures show the front and back side of the backplane.
Figure 21 Backplane Connectors / 4 3.5” HDD Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Removal and replacement procedures 61
Figure 22 Backplane Connectors / 8 3.5” HDD Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Figure 23 Backplane Connectors / 8 2.5” HDD Model (component side)
Item
Description
1
LED indicators
2
Screw holes
3
Headers for hard drive
Removal and replacement procedures 62
Figure 24 Backplane Connectors / 12 3.5” HDD Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Figure 25 Backplane Connectors / 25 2.5” HDD Model (component side)
Item
Description
1
Screw holes
2
LED indicators
3
Headers for hard drive
Removal and replacement procedures 63
Figure 26 Backplane Connectors / 4 3.5” HDD Model (solder side)
Item
Description
1
Power connector
2
Mini SAS connector
3
PROG connector
4
I2C connector
Figure 27 Backplane Connectors / 8 3.5” HDD Model (solder side)
Item
Description
1
Power connector
2
PIC 2 PROG connector
3
PIC 1 PROG connector
Removal and replacement procedures 64
Item
Description
4
I2C connector
5
Mini SAS connector 1
6
Mini SAS connector 2
Figure 28 Backplane Connectors / 8 2.5” HDD Model (solder side)
Item
Description
1
PIC 2 PROG connector
2
Power connector
3
I2C connector
4
PIC 1 PROG connector
5
Mini SAS connectors
Removal and replacement procedures 65
Figure 29 Backplane Connectors / 12 3.5” HDD Model (solder side)
Item
Description
1
Power connector 1
2
PROG connector
3
SAS/SATA expander chip with heat sink covered
4
Mini SAS connector
5
HDD LED connector
6
I2C connector
7
HDD 14 connector
8
HDD 13 connector
9
Power connector 2
Removal and replacement procedures 66
Figure 30 Backplane Connectors / 25 2.5” HDD Model (solder side)
Item
Description
1
Power connector 1
2
Power connector 2
3
SAS/SATA expander chip with heat sink covered
4
CPLD PROG connector
5
I2C connector
6
Mini SAS connector 1
7
Mini SAS connector 2
WARNING: Ensure that the system is powered off and all power sources have been disconnected
from the server. Voltages are present at various locations within the server whenever an AC power
source is connected. This voltage is present even when the main power switch is in the off position.
Removal and replacement procedures 67
To remove the backplane:
1.
Remove all drives out of the drive bays.
Refer to the “Optical disc drive bay” and “Hard drives” sections in this chapter for detailed
procedures.
2.
Remove the top cover.
3.
Remove all cables connected to the backplane.
4.
Remove the backplane.
a. Remove the three screws that secure the backplane to the hard drive cage.
b. Pull the backplane up and out to release it from the hard drive cage.
Figure 31 Removing the Backplane
To reinstall the backplane:
1.
Orient the backplane so that the notches on the backplane align with the hook on the drive cage
and then press the backplane down until it clicks into place.
2.
Secure the backplane with three screws.
Removal and replacement procedures 68
Figure 32 Reinstalling the Backplane
3.
Install all necessary cables.
Removal and replacement procedures 69
System board configuration
Processor
HP ProLiant DL288 G6 Server supports Intel Xeon 5500 and 5600 Series processors. If a single
processor is installed, then use socket 1. When two processors are used, the server supports boot
functions through the processor installed in socket 1. However, if processor 1 fails, the system cannot
boot up, and if processor 2 fails, the system will be automatically booted from processor 1 and
provide a processor failure message.
The processor socket supports 2P Intel Xeon processor with integrated memory controller.
CAUTION: It is recommended to use processors of the same speeds or cache sizes to prevent
possible server malfunction.
Figure 33 Processor Locations
Item
Description
1
Processor 1
2
Processor 2
WARNING: To reduce the risk of personal injury from hot surfaces, allow the heat sink and the
processor to cool before touching them.
NOTE: Before installing the processor, remove the air baffle.
Removal and replacement procedures 70
To remove the air baffle:
1.
Gently rock the air baffle up.
2.
Take the air baffle out from the system board.
Figure 34 Removing the Air Baffle
To remove the heat sink:
1.
Loosen the two spring-loaded screws.
2.
Lift the heat sink away from the system board.
CAUTION: Place the heat sink down in an upright position with the thermal patch facing upward.
Do not let the thermal patch touch the work surface.
Figure 35 Removing the Heat Sink Assembly
IMPORTANT: If the heat sink has been removed for any reason on a previously installed processor, it
is critical that you clean any residue of the old thermal compound with alcohol and apply more
thermal grease compound to the integrated heat spreader on the processor to ensure proper thermal
bonding between the processor and the heat sink.
Removal and replacement procedures 71
CAUTION: Do not over-tighten the spring-loaded screws to prevent them from breaking off. A
maximum torque of 6 inch-lb is set for each screw. Rotate the heat sink a few degrees to the left and
right to break the bonding of the thermal grease compound before removing the heat sink from the
processor.
To remove the processor:
1.
Open the processor locking lever.
2.
Open the processor socket retaining bracket.
Figure 36 Opening the lever and bracket
CAUTION: The pins of the socket are very fragile. Do not bend or damage them.
CAUTION: Place the processor on a static-dissipating work surface or in an anti-static bag.
CAUTION: To allow heat sink to draw as much heat as possible from the processor base, there must
be good contact between the heat sink base and the top of the processor. To ensure good contact,
you must first remove any residue of the old thermal compound with alcohol and apply new thermal
grease compound.
3.
Using the processor removal tool, remove the processor from the system board.
a. Line up the processor tool, ensuring the locking lever graphic on the tool is
correctly oriented.
b. Press in on the plastic tabs, and then place the tool on the processor.
c.
Release the tabs, and then carefully lift the processor and tool straight up.
Removal and replacement procedures 72
Figure 37 Removing the Processor
4.
Carefully rotate the tool, and then push in and release the tabs to secure the processor in the
tool.
Figure 38 Removing the Processor
CAUTION: To avoid damage to the processor, do not touch the bottom of the processor, especially
the contact area.
Removal and replacement procedures 73
To apply the thermal grease compound:
1.
Use a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and the
new processor. Wipe the contact surfaces several times to make sure that no particles or dust
contaminants are evident.
2.
Apply the thermal grease compound to the CPU contact surface.
CAUTION: HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant
server.
3.
Apply new grease to the top of the processor using a five-dot pattern to ensure even distribution.
Figure 39 The top of the Processor
CAUTION: Never touch the bottom of the processor; any contaminant could prevent the mounting
pads from making contact with the socket.
CAUTION: Applying too much grease creates a gap between the contact surfaces, significantly
reducing the ability of the heat sink to draw out heat. Installing the heat sink with excessive grease
can also cause the grease to spread over the processor pins or the system board base, which can
cause electrical shorts that damage the system.
CAUTION: To prevent damage to processor socket pins the processor installation tool must be used
to insert the processor into the socket. Instructions are provided in the Option Kits and spare part
kits.
To install a processor:
CAUTION: Failure to completely open the processor locking lever prevents the processor from
seating during installation, leading to hardware damage.
1.
Open the processor locking lever and the processor socket retaining bracket. DO NOT REMOVE
THE PROCESSOR SOCKET COVER
Removal and replacement procedures 74
Figure 40 Opening the lever and bracket
IMPORTANT: Be sure the processor remains inside the processor installation tool.
2.
If the processor has separated from the installation tool, carefully re-insert the processor in the
tool. Handle the processor by the edges only, and do not touch the bottom of the processor,
especially the contact area.
Figure 41 Installing the processor in the installation tool
Removal and replacement procedures 75
3.
Be sure the tool is oriented correctly. Align the processor installation tool with the socket, and
then install the processor. THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY
DAMAGED.
Figure 42 Installing the Processor
CAUTION: THE PINS ON THE SYSTEM BOARD ARE VERY FRAGILE AND EASILY DAMAGED. To avoid
damage to the system board:
• Never install or remove a processor without using the processor installation tool.
• Do not touch the processor socket contacts.
• Do not tilt or slide the processor when lowering the processor into the socket.
4.
Press and hold the tabs on the processor installation tool to separate it from the processor, and
then remove the tool.
Removal and replacement procedures 76
Figure 43 Removing the processor installation tool
5.
Close the processor socket retaining bracket and the processor locking lever.
Figure 44 Closing the processor socket
CAUTION: Be sure to close the processor socket retaining bracket before closing the processor
locking lever. The lever should close without resistance. Forcing the lever closed can damage the
processor and socket, requiring system board replacement.
6.
Apply all the grease to the top of the processor in the following pattern to ensure even
distribution.
Removal and replacement procedures 77
Figure 45 The top of the processor
CAUTION: To prevent overheating or a possible system crash, use only a heat sink model specified
for the HP ProLiant DL288 G6 server.
To install the heat sink:
1.
Properly align the heat sink spring-loaded screws to the system board mounting holes.
2.
Tighten the spring-loaded screws clockwise to secure the heat sink connection to the system
board.
Figure 46 Installing the Heat Sink Assembly
NOTE: When installing two heat sinks, it is recommended to put the heat sinks with the 14-fin side
facing the DIMMs.
CAUTION: For proper cooling, do not operate the server without the top cover, air baffle, expansion
slot covers, or blanks installed. For additional information, see the user guide. If hot-plug
components are supported, minimize the amount of time the top cover is removed.
Removal and replacement procedures 78
To install the air baffle:
1.
Connect all necessary cables.
2.
Gently place the air baffle on the system board.
Figure 47 Installing the Air Baffle
Memory
The system board has twelve DIMM slots that support up to 192 GB maximum system memory (Two
16 GB Quad-rank or Dual-rank DIMMs in each of the four channels).
You must adhere to the following guidelines when adding or replacing memory modules:
•
•
•
•
For 2P system, both physical processors must be of the same type and speed.
Use 800/1066/1333 MHz DDR3 RDIMM/UDIMM.
Supported DIMM capacity: 2 GB, 4 GB, 8 GB and 16 GB
Installation guide for 1P configuration:
○ Follow the sequence of 2A, 4B, 6C, 1D, 3E, and 5F for the corresponding processor when
installing the memory.
•
Installation guide for 2P configuration:
○ Follow the sequence of 2A, 4B, 6C, 1D, 3E, and 5F for the corresponding processor when
installing the memory.
○ Install at least one memory DIMM for each processor.
○ The memory quantity installed for each processor can be different.
Removal and replacement procedures 79
Figure 48 DIMM Population
Figure 49 DIMM Slots
NOTE: Before installing the memory, remove the air baffle first. For a detailed procedure, see
the ”Processor” section in this chapter.
Removal and replacement procedures 80
To remove the memory module:
1.
Completely open the holding clips securing the memory module.
2.
Gently pull the memory module upward to remove it from the slot.
Figure 50 Removing the Memory Module
CAUTION: Place the memory module on a static-dissipating work surface or inside of an anti-static
bag.
To install the memory module:
1.
Align the notch on the bottom edge of the memory module with the keyed surface of the DIMM
slot and then fully press the memory module into the slot until the holding clips snap back in
place.
Figure 51 Installing the Memory Module
CAUTION: The DIMM slots are structured to ensure proper installation. If you insert a DIMM but it
does not fit easily into the slot, you may have inserted it incorrectly. Reverse the orientation of the
DIMM and insert it again.
Removal and replacement procedures 81
DIMM identification
IMPORTANT: This server does not support mixing RDIMMs and UDIMMs. Attempting to mix these
two types causes the server to halt during BIOS initialization.
The memory subsystem may be populated with either RDIMMs or UDIMMs, but mixing
the two types is not supported. To determine DIMM characteristics, use the label
attached to the DIMM and the following illustration and table.
Figure 52 DIMM identification
Item
Description
Definition
1
Size
—
2
Rank
1R = Single-rank
2R = Dual-rank 4R = Quad-rank
3
Data width
x4 = 4-bit
x8 = 8-bit
4
Memory speed
10600 = 1333-MHz
8500 = 1067-MHz
5
DIMM type
R = RDIMM (registered)
E = UDIMM (unbuffered with ECC)
Removal and replacement procedures 82
PCI expansion card
System board PCI expansion slot
There are three PCI expansion slots on the system board.
Figure 53 System Board PCI Expansion Slots
Item
Component
Designator
Component
Function
1
J31
PCIe x4 (FH/FL) slot 1b
Supports a PCIe riser card or PCIe & PCI-X riser card
2
J17
PCIe x16 (FH/FL) slot 1a
Supports a PCIe riser card or PCIe & PCI-X riser card
3
J18
PCIe x16 (LP) slot 2
Supports a PCIe riser card
Removal and replacement procedures 83
PCI riser card expansion slot
The one PCIe riser card attached to the PCI cage converts the functionality of the system board
expansion slot to the slot positioned at a 90° angle from the system board.
NOTE: Users have the option to replace the standard riser card in slot 1a&1b with other four models
using the dual PCIe x8 riser card, single PCIe x16 riser card, dual PCI-X riser card, or PCIe x16 &
dual PCI-X riser card option kit. This will allow support for PCIe x8, PCIe x16, and PCI-X devices.
Figure 54 Three PCIe x8 Riser Card Connector Location
•
Three slots PCIe riser card (Three x8 link with x8 slots)
Figure 55 Two PCIe x8 Riser Card Connector Location
•
Two slots PCIe riser card (Two x8 link with x8 slots)
Removal and replacement procedures 84
Figure 56 PCIe x16 Riser Card Connector Location
•
One slot PCIe riser card (x16 link with x16 slots)
Removal and replacement procedures 85
PCI cage
The server supports three types of PCI cages. They are the standard PCI cage, the HDD PCI cage, the
ODD PCI cage.
The table below identifies the PCI cages by their function and shows their corresponding server type
and supported riser cards.
PCI cage
Riser Card
System model
Standard PCI Cage
Slot 1a&1b:
4 3.5” HDD model;
dual PCIe x8 riser card for standard PCI
cage;
8 3.5” HDD model;
or three PCIe x8 riser card
12 3.5” HDD model;
or PCIe x16 + dual PCI-X riser card
8 2.5” HDD model;
25 2.5” HDD model;
or dual PCI-X riser card
or single PCIe x16 riser card (Full-height
/ Full-length Side)
Slot 2:
single PCIe x16 riser card (Low Profile)
Rear HDD PCI cage
Slot 2:
12 3.5” HDD model
single PCIe x16 riser card (Low Profile)
Rear Optical Disc Drive
PCI cage
Slot 1a&1b:
4 3.5” HDD model;
dual PCIe x8 riser card for Optical Disc
Drive PCI cage
8 3.5” HDD model;
8 2.5” HDD model;
12 3.5” HDD model;
25 2.5” HDD model;
Removal and replacement procedures 86
To remove the PCI cage:
NOTE: Disconnect all cables connecting an existing expansion board to the system board.
1.
Loosen the thumbscrews that secure the PCI cage to the system board and remove the screw that
secures the PCI cage to the rear of the server.
2.
Lift the PCI cage away from the system board.
Figure 57 Removing the PCI Cage
Installing PCIe riser card
The system supports up to two riser cards at a time. Use only HP supported expansion boards that
meet the following specifications:
•
Compliance
○ PCIe x8 or x16 (FH, FL)
○ PCIe x16 (LP)
○ PCI-X (FH, FL)
•
Form Factor
○ Full-Height/Full-Length
○ Low-Profile
○ Full-Height/Half-Length
Removal and replacement procedures 87
To remove the PCIe riser card:
1.
Loosen the screw securing the riser card to the PCI cage.
2.
Remove the riser card from the PCI cage.
Figure 58 Removing the Three PCIe x8 Riser Card
Figure 59 Removing the two PCIe x8 Riser Card
Removal and replacement procedures 88
Figure 60 Removing the PCIe x16 Riser Card
Removal and replacement procedures 89
To install the PCIe riser card:
1.
Align the three riser card locking-tab holes to the corresponding standoffs on the PCI cage, and
then push the card rightwards.
2.
Tighten the screw that secures the riser card to the PCI cage.
Figure 61 Installing the Three PCIe x8 Riser Card
Figure 62 Installing the Two PCIe x8 Riser Card
1.
Align the four riser card locking-tab holes to the corresponding screw standoffs on the PCI cage.
2.
Tighten the screws that secure the riser card to the PCI cage.
Removal and replacement procedures 90
Figure 63 Installing the PCIe x16 Riser Card
Removal and replacement procedures 91
To install the PCI expansion board:
1.
Remove the screw near the slot cover on the PCI cage.
Figure 64 Removing the Screw on the PCI Cage on the Full-height / Full-length Side
Figure 65 Removing the Screw on the PCI Cage on the Low-profile Side
Removal and replacement procedures 92
2.
Remove the slot cover from the PCI cage.
3.
Slide the expansion board into the slot, aligning the board with its matching connector.
Firmly press the board to seat it properly on the slot.
4.
Tighten the screw that secures the expansion board to the PCI cage.
Figure 66 Installing the Three PCIe x8 Expansion Board
Figure 67 Installing the Two PCIe x8 Expansion Board
Removal and replacement procedures 93
Figure 68 Installing the PCIe x16 Expansion Board
Removal and replacement procedures 94
To reinstall the PCI cage:
The following figures show the front and back side of the backplane.
Figure 69 Backplane Connectors / 2 3.5” HDD Model (component side)
Item
Description
1
Screw hole
2
LED indicators
3
Headers for hard drive
Figure 70 Backplane Connectors / 2 3.5” HDD Model (solder side)
Item
Description
1
I2C connector
2
SGPIO connector
Removal and replacement procedures 95
Item
Description
3
PIC PROG connector
4
HDD 13 connector
5
Power connector
6
HDD 14 connector
7
HDD LED connector
1.
Install the PCI expansion board into the PCI cage.
a. Align the PCI expansion board with the open expansion slot.
b. Press the PCI expansion board into the expansion slot on the riser card.
c.
Tighten the screw that secures the expansion board to the PCI cage.
2.
Align the PCI cage assembly to the system board expansion slot, and then press it down to
ensure full connection to the system board.
3.
Tighten the thumbscrews to secure the PCI cage assembly to the system board and secure the
screw on the rear panel of the chassis.
Figure 71 Reinstalling the PCI Cage with PCI Expansion Board
4.
Connect the necessary cable(s) to the system board.
Removal and replacement procedures 96
To install the HDD PCI cage:
1.
Loosen the thumbscrew and screws that secure the HDD PCI cage to the system board.
2.
Lift the HDD PCI cage assembly away from the system board.
Figure 72 Removing the HDD PCI Cage Assembly
3.
Align the four backplane holes to the corresponding standoffs on the HDD PCI cage, and then
push the card down.
4.
Tighten the screw that secures the backplane to the HDD PCI cage.
Figure 73 Installing the 2HDD Backplane
Removal and replacement procedures 97
5.
Align the HDD PCI cage assembly to the system board expansion slot, and then press it down to
ensure full connection to the system board.
6.
Tighten the thumbscrew to secure the HDD PCI cage assembly to the system board and secure
the screws on the side and the rear panel of the chassis.
Figure 74 Installing the HDD PCI Cage Assembly
7.
Pull the rear hard drive blank out of the HDD PCI cage assembly.
Figure 75 Removing the Rear Hard Drive Blank
Removal and replacement procedures 98
8.
Push the hard dive assembly into the drive bay until it stops.
9.
Press the HDD carrier latch inward until it clicks.
Figure 76 Installing the Rear Hard Drive
To install the Optical Disc Drive PCI cage:
1.
Loosen the thumbscrews that secure the optical disc drive PCI cage to the system board and
remove the screw on the rear panel of the chassis.
2.
Lift the optical disc drive PCI cage away from the system board.
Figure 77 Removing the optical disc drive PCI Cage
Removal and replacement procedures 99
3.
Pushing the optical disc drive ROM into the ODD PCI cage.
Figure 78 Pushing the optical disc drive DVD-ROM into the ODD PCI Cage
4.
Tighten the screw that secures the optical disc drive to the ODD PCI cage.
Figure 79 Securing the Optical Disc Drive
Removal and replacement procedures 100
5.
Align the ODD PCI cage assembly to the system board expansion slot, and then press it down to
ensure full connection to the system board.
6.
Tighten the thumbscrews to secure the ODD PCI cage assembly to the system board and secure
the screw on the rear panel of the chassis.
Figure 80 Reinstalling the ODD PCI Cage Assembly
Removal and replacement procedures 101
Dedicated management port (Optional)
The server can support a dedicated management port. The dedicated management port is optional for
the shipment.
The following figure shows the dedicated management port location.
Figure 81 Dedicated management port Location
Removal and replacement procedures 102
To remove the dedicated management port:
1.
Remove the PCI cage assembly out of the chassis.
Refer to the “PCI cage” section in this chapter for detailed procedures.
2.
Loosen the screw.
3.
Pull the dedicated management port upwards, and then remove the dedicated management port
from the dedicated management port connector.
Figure 82 Removing the dedicated management port
4.
Remove the spacer from the system board.
Figure 83 Removing the Spacer
Removal and replacement procedures 103
To reinstall the dedicated management port:
1.
Remove the dedicated management port cover.
Figure 84 Removing the Dedicated management Port Cover
2.
Insert the spacer into the system board.
Figure 85 Inserting the Spacer
Removal and replacement procedures 104
3.
Align the dedicated management port to the plastic standoff, and insert the dedicated
management port into the dedicated management port connector.
4.
Tighten the screw clockwise to secure the dedicated management port to the system board.
Figure 86 Reinstalling the Dedicated management port
TPM Module (Optional)
The server can support a TPM module. The TPM module is optional for the shipment.
The following figure shows the TPM module location.
Figure 87 TPM module Location
To remove the Dedicated management port:
1.
Remove the security rivet from the system board
Removal and replacement procedures 105
Figure 88 Removing the security rivet
2.
Remove the TPM card from system board.
Figure 89 Removing the TPM card
To reinstall the dedicated management port:
1.
Install the TPM card. Press down the TPM card to the connector to seat on the system board
Removal and replacement procedures 106
Figure 90 Inserting the TPM card
2.
Insert the TPM security rivet by pressing the rivet firmly into the system board
Figure 91 Inserting security rivet
System battery
The server uses nonvolatile memory that requires a system battery to retain system information when
power is removed.
This 3 V lithium coin cell battery is located on the system board.
Removal and replacement procedures 107
Figure 92 System Battery Location
WARNING: Note the following reminders when replacing the system battery:
• Replace the system battery with the same type as the system battery recommended by HP. Use of
another system battery may present a risk of fire or explosion.
• A risk of fire and chemical burn exists if the system battery is not handled properly. Do not
disassemble, crush, puncture, or short external contacts, or expose the system battery to
temperatures higher than 60°C (140°F).
• Do not dispose of used system battery in water or fire. Dispose of used system battery according
to manufacturer's instructions.
CAUTION: Loss of BIOS settings occurs when the system battery is removed. You must reconfigure
BIOS settings whenever you replace the system battery.
NOTE: If the server no longer automatically displays the correct date and time, you may need to
replace the system battery. Under normal usage, system battery life is five to ten years.
To replace the system battery:
1.
Power down the server.
2.
Disconnect the power cord(s).
3.
Unlock the server if necessary and remove the top cover as described in the section “System
cover”.
NOTE: If the expansion board is installed to the PCI cage, remove the PCI cage before releasing the
battery. Refer to the “PCI cage” section in this chapter for detailed procedures.
4.
Release the battery from its holder by squeezing the metal clamp that extends above one edge of
the battery. When the battery pops up, lift it out.
5.
To insert the new battery, slide one edge of the replacement battery under the holder’s lip with
the positive side up. Push the other edge down until the clamp snaps over the other edge of the
battery.
Removal and replacement procedures 108
Figure 93 Replacing the System Battery
Removal and replacement procedures 109
BBWC (Optional)
The system board can support up to two BBWC. The BBWC is optional for the shipment.
Figure 94 BBWC Locations
To remove the BBWC:
1.
Pull the BBWC retaining latch.
2.
Slide the BBWC back, up and out of the tray.
Figure 95 Removing the BBWC
Removal and replacement procedures 110
To reinstall the BBWC:
1.
Pull the BBWC retaining latch.
2.
At the same time, align the locking tabs on the BBWC to their holes on the tray. Press the BBWC
into the tray, and then push it along the direction of the arrow to lock the locking tabs.
Figure 96 Reinstalling the BBWC
Removal and replacement procedures 111
System board removal and replacement procedure
To remove the system board:
1.
Remove the top cover.
2.
Loose the nine screws that secure the system board to the chassis.
3.
Slide the system board back, up and out of the chassis. Remove the system board from the
chassis.
Figure 97 Removing the System Board
Removal and replacement procedures 112
To reinstall the system board:
1.
Align the system board I/O connectors to their openings and slide the system board into place.
The nine screw holes on the chassis should align with the system board.
2.
Fasten the nine screws on the system board to secure the system board to the chassis.
Figure 98 Reinstalling the System Board
Removal and replacement procedures 113
Power supply unit (PSU)
Located on the rear panel of the server power supply is designed with three types of power supply
units. They are 460 W and 750 W PSU with power factor correction (PFC) function. Table 20 lists
how to configure the power supply with the different system models.
Table 20 Power Supply Unit Configurations
System model
Power supply unit
4 3.5” HDD model
One or two 460 W power supply unit
8 3.5” HDD model
One or two 460 W power supply unit
8 2.5” HDD model
One or two 460 W power supply unit
12 3.5” HDD model
One or two 750 W power supply unit
25 2.5” HDD model
One or two 750 W power supply unit
Figure 99 Power Supply Unit
WARNING: Take note of the following reminders to reduce the risk of personal injury from electric
shock hazards and/or damage to the equipment.
• Installation of power supply units should be referred to individuals who are qualified to service
server systems and are trained to deal with equipment capability of generating hazardous
energy levels.
• DO not open the power supply unit. There are no serviceable parts inside it.
To remove the power supply:
1.
Press the port wine colored tab.
2.
Slide the hot-plug power supply out of the power supply bay.
Removal and replacement procedures 114
Figure 100 Removing the Power Supply
To reinstall the power supply:
1.
Press the release tabs of the power supply blank, and then pull the power supply blank out of the
chassis.
Figure 101 Removing the Power Supply Blank
2.
Align the hot-plug power supply cage connector with the open power supply bay and slide the
power supply into the chassis.
3.
Snap the latch cover over port colored handle. Latch cover only installs one way.
Removal and replacement procedures 115
Figure 102 Reinstalling the Power Supply
Removal and replacement procedures 116
System fan cage
The server supports two kinds of fan cage. The system redundant fan cage is optional for shipment.
•
•
System non-redundant fan cage
System redundant fan cage
Figure 103 System Non-redundant Fan Cage
Figure 104 System Redundant Fan Cage
Removal and replacement procedures 117
To remove the system non-redundant fan cage
1.
Remove all screws on the system non-redundant fan cage.
2.
Lift the system fan cage up and out of the chassis.
Figure 105 Removing the System Non-redundant Fan Cage
To remove the system redundant fan cage
1.
Loosen the screws that secure the system redundant fan cage.
2.
Lift the system fan cage up and out of the chassis.
Figure 106 Removing the System Redundant Fan Cage
To reinstall the system non-redundant fan cage
1.
Align the system non-redundant fan cage to the chassis, press the system non-redundant fan cage
down.
2.
Tighten the screws that secure the system fan cage.
Removal and replacement procedures 118
Figure 107 Reinstalling the System Non-redundant Fan Cage
To install the system redundant fan cage
1.
Get eight screws from the existing system non-redundant fan cage. See figure “Figure 105 “
2.
Remove the foam on the system redundant fan cage.
Figure 108 Removing the foam
3.
The redundant fan kit has 4 fans installed on the cage. Squeeze the release tab on the system
fan and lift the system fan away from the fan cage.
Figure 109 Removing the system fans
Removal and replacement procedures 119
4.
Locate the system fan cage on the chassis and vertical wall.
5.
Fasten the screws.
Figure 110 Installing the System Redundant Fan Cage
6.
Install the foam on the system redundant fan cage.
7.
Paste the mylar on the fan bracket.
Figure 111 Installing the Foam and Mylar
Removal and replacement procedures 120
Removal and replacement procedures 121
System fan
The server has four or eight system fans located on the center wall of the chassis. While the server is
equipped with eight system fans, the redundant function is provided.
The figure below identifies the system fans by their device number and shows their corresponding
cable connections.
Figure 112 Connection of the Four System Fans
Device number
Connector
System fan 1
J63 on the system board
System fan 2
J71 on the system board
System fan 3
J62 on the system board
System fan 4
J68 on the system board
System fans 1 to 3 are for the memory modules and processors, while system fan 4 is for the PCI slots and system
chipsets.
Removal and replacement procedures 122
Figure 113 Connection of the Eight System Fans
Device number
Connector
System fan 1/2
J63 on the system board
System fan 3/4
J71 on the system board
System fan 5/6
J62 on the system board
System fan 7/8
J68 on the system board
System fans 1 to 6 are for the memory modules and processors, while system fan 7/8 is for the PCI slots and system
chipsets.
A new system fan can be installed to allow the server to operate properly in case a default system fan
becomes defective.
The installation and removal of fans on the system redundant fan cage and system non-redundant fan
cage are same, here we take the removal and installation of fans on the system non-redundant fan
cage for example.
To remove the system fan:
1.
Power down the server.
2.
Disconnect the power cord(s).
3.
Unlock the server if necessary and remove the top cover as described in the section “System
cover”.
4.
Disconnect the system fan cable from its corresponding board connector.
5.
Release the fan cable from the cable clip securing it to the chassis partition wall.
6.
Squeeze the release tab on the system fan to release it from the chassis.
7.
Lift the system fan away from the chassis.
Removal and replacement procedures 123
Figure 114 Removing the System Fan
To reinstall the system fan:
1.
Hold the system fan and press it into the system fan bracket.
2.
Secure the cable using the cable clip located on the chassis partition wall.
3.
Connect the system fan cable to its corresponding board connector.
Figure 115 Reinstalling the System Fan
Removal and replacement procedures 124
Connectors, switches, and LEDs
This chapter contains illustrations and tables identifying and describing the connectors, jumpers,
switch, buttons, and LED indicators located on the front panel, rear panel, system board and hard
drives of the HP ProLiant DL288 G6 server.
Connectors and components
Front panel components
Figure 116 Front Panel Components / 4 3.5” HDD Model
Item
Description
1
Front panel USB 2.0 port 0/1
2
Optical disc drive
3
System health LED
4
Front UID LED/switch
5
NIC 1 activity LED
6
NIC 2 activity LED
7
Hard Drive activity LED
8
Power LED/switch
9
Thumbscrews for rack mounting
10
Drive online/error LED
11
Drive activity LED
Connectors, switches, and LEDs 125
Item
Description
12
Hard disk drive (HDD) bays
Figure 117 Front Panel Components / 8 3.5” HDD Model
Item
Description
1
Front panel USB 2.0 port 0/1
2
Optical disc drive
3
Front UID LED/switch
4
System health LED
5
NIC 1 activity LED
6
NIC 2 activity LED
7
Hard drive activity LED
8
Power LED/switch
9
Thumbscrews for rack mounting
10
Drive activity LED
11
Drive online/error LED
12
Hard disk drive (HDD) bays
Connectors, switches, and LEDs 126
Figure 118 Front Panel Components / 8 2.5” HDD Model
Item
Description
1
Front panel USB 2.0 port 0/1
2
Optical disc drive
3
Front UID LED/switch
4
System health LED
5
NIC 1 activity LED
6
NIC 2 activity LED
7
Hard drive activity LED
8
Power LED/switch
9
Thumbscrews for rack mounting
10
Drive activity LED
11
Drive online/error LED
12
Hard disk drive (HDD) bays
Connectors, switches, and LEDs 127
Figure 119 Front Panel Components / 12 3.5” HDD Model
Item
Description
1
Front panel USB 2.0 port 0/1
2
System health LED
3
Front UID LED/switch
4
NIC 1 activity LED
5
NIC 2 activity LED
6
Hard drive activity LED
7
Power LED/switch
8
Thumbscrews for rack mounting
9
Drive online/error LED
10
Drive activity LED
11
Hard disk drive (HDD) bays
Connectors, switches, and LEDs 128
Figure 120 Front Panel Components / 25 2.5” HDD Model
Item
Description
1
Front panel USB 2.0 port 0/1
2
System health LED
3
Front UID LED/switch
4
NIC 1 activity LED
5
NIC 2 activity LED
6
Hard drive activity LED
7
Power LED/switch
8
Thumbscrews for rack mounting
9
Drive online/error LED
10
Drive activity LED
11
Hard disk drive (HDD) bays
Connectors, switches, and LEDs 129
Rear panel components
Figure 121 Rear Panel Components for Standard PCI Cage
Item
Description
1
Power supply 2 cable socket
2
Serial port
3
T-10/T-15 wrench
4
GbE LAN port for NIC 2
5
Dedicated management port (optional)
6
Low-profile PCI expansion card slot cover
7
Full-height/full-length PCI expansion card slot covers
8
Rear UID LED/switch
9
GbE LAN port for NIC 1
10
Rear panel USB 2.0 port 2/3
11
VGA port
12
Power supply 1 cable socket
Connectors, switches, and LEDs 130
Figure 122 Rear Panel Components for HDD PCI Cage
Item
Description
1
Power supply 2 cable socket
2
Serial port
3
T-10/T-15 wrench
4
GbE LAN port for NIC 2
5
Dedicated management port (optional)
6
Low-profile PCI expansion card slot cover
7
Hard disk drive (HDD) bay
8
Rear UID LED/switch
9
GbE LAN port for NIC 1
10
Rear panel USB 2.0 port 2/3
11
VGA port
12
Power supply 1 cable socket
Connectors, switches, and LEDs 131
Figure 123 Rear Panel Components for ODD PCI Cage
Item
Description
1
Power supply 2 cable socket
2
Serial port
3
T-10/T-15 wrench
4
GbE LAN port for NIC 2
5
Dedicated management port (optional)
6
Optical disk drive (ODD) bay
7
Full-height/full-length PCI expansion card slot covers
8
Rear panel USB 2.0 port 2/3
9
GbE LAN port for NIC 1
10
Rear UID LED/switch
11
VGA port
12
Power supply 1 cable socket
Connectors, switches, and LEDs 132
System board components
Figure 124 System Board Components
Item
Designator
Description
1
J17
PCIe slot
2
J11
Dedicated management port connector
3
J18
PCIe slot
4
J21
DIMM slot 6C for processor 2
5
J26
DIMM slot 1D for processor 2
6
CPU2
Processor 2
7
J48
DIMM slot 6C for processor 1
8
J60
4-pin power connector
9
J43
DIMM slot 1D for processor 1
10
J51
System power connector
11
CPU1
Processor 1
12
J63
Fan connector 1
13
J71
Fan connector 2
14
J64
8-pin power connector
15
J62, J70
Fan connector 3/4 (Fan 4 is unused)
16
J69
Internal USB 2.0 port 4
17
J65
Backplane I2C connector
18
J68, J67
Fan connector 5/6 (Fan 6 is unused)
19
J66
Hard drive backplane SGPIO connector
20
J79
Power supply EFF connector
Connectors, switches, and LEDs 133
Item
Designator
Description
21
B1
3 V CMOS battery (CR2032)
22
J76
Power backplane control connector
23
J56
LCD connector (optional)
24
J53
Front panel USB 2.0 port 0/1
25
J42
Front panel header
26
J29
TPM connector
27
J27
System maintenance jumper
28
SATA
SATA connectors
29
J31
PCIe slot
Jumpers
The system board contains a system maintenance jumper (J27). Table 21 describes the jumper
settings.
Table 21 System Maintenance Jumper Setting (J27)
Jumper
Status (default=off)
A
Clear CMOS
B
Clear password
C
Recovery BIOS
D
Recovery BMC
E
RTC reset
Connectors, switches, and LEDs 134
LED indicators
This section contains illustration and descriptions of internal and external status LED indicators located
on the:
•
•
•
•
•
Front panel
Optical disc drive
Hard drive
Rear panel
System board
These LED indicators aid in problem diagnosis by indicating the status of system components and
operations of the server.
Front panel LED indicators
The front panel LED indicators allow constant monitoring of basic system functions while the server is
operating.
Figure 125 Front Panel LED Indicators on the Right Ear
Table 22 Front Panel LED Indicator Status on the Right Ear
Item
LED indicator
Status
Description
1
System health LED
Steady green
Healthy
Red
Critical error
Amber
Non-critical error
Steady green
Linked to the network
Flashing green
Linked and activity on the network.
Off
No connection
2
NIC 2 activity LED
Connectors, switches, and LEDs 135
Table 22 Front Panel LED Indicator Status on the Right Ear
Item
LED indicator
Status
Description
3
Hard drive activity LED
Flashing green
Hard drive activity
Off
No hard drive activity
Steady green
The system has AC power and is turned on.
Steady amber
The system has AC power but in standby
mode.
Off
No AC power to the system.
Steady green
Linked to the network
Flashing green
Linked and activity on the network.
Off
No connection
Steady blue
Identification.
Flashing blue
The system is being remotely managed.
Off
No identification.
4
5
6
Power LED/switch
NIC 1 activity LED
Front UID LED/switch
Optical disc drive activity LED indicator
The optical disc drive has an activity indicator that indicates when the drive is reading media.
Figure 126 Optical disc drive activity LED indicator
Table 23 Optical Disc Drive Activity LED Indicator Status
Item
Component
Status
Description
1
Optical disc drive activity LED
indicator
Flashing green
Ongoing drive activity.
Off
No drive activity.
Connectors, switches, and LEDs 136
Hard drive LED indicator
The status of hard drives installed in the server is indicated by the hard drive LED indicators located
on the HDD.
Figure 127 Hard Drive LED Indicator
Table 24 Hard Drive LED Indicator Status
Item
LED indicator
Status
Description
1
Drive online/error LED indicator
Steady blue
The drive is located
Steady orange
The drive is in a failed state.
Off
The drive is not in a failed state.
Flashing green
The drive is in an activity state.
Off
The drive is not in an activity state.
2
Drive activity LED indicator
Connectors, switches, and LEDs 137
Rear panel LED indicators
The LAN port on the rear panel has two LED indicators that allow monitoring of network activity.
Figure 128 LAN LED Indicators Location
Table 25 LAN LED Indicator Status
Item
Component
Status
Description
1
NIC activity LED indicator
Flashing green
Linked and activity on the network.
Off
No connection or linking at 10 Mbps
speed.
Flashing green
LAN is active.
Steady green
LAN is linking.
Flashing amber
LAN is active.
2
NIC link LED indicator
3
Dedicated management port
activity LED indicator (optional)
4
Dedicated management port link Steady green
LED indicator (optional)
Off
Linking at 100 Mbps speed.
No connection or linking at 10 Mbps
speed.
Connectors, switches, and LEDs 138
System board LED indicator
The system board contains one LED indicator for use during troubleshooting operations.
Figure 129 System Board LED Indicator
Table 26 BMC activity LED Indicator Status
Item
Component
Status
Description
1
BMC activity LED indicator
Steady green
BMC is power on and in initialization process.
Flashing green
BMC activity.
Off
AC is Off.
Connectors, switches, and LEDs 139
Diagnostic tools and setup utilities
This chapter provides an overview of the Power-On Self-Test (POST), the POST error messages, and
BIOS, SAS and SATA setup utilities.
BIOS software
The server uses BIOS to boot up the system. BIOS software is a ROM-based firmware that allows
reliability, manageability, and connectivity for the server platforms. This software contains a set of
programs permanently stored in an EEPROM chipset located on the system board. These programs
assist in managing, initializing, and testing the hardware devices installed on the computer.
BIOS software allows you to:
•
Perform configuration from the BIOS Setup Utility
Using the Setup Utility, you can install, configure, and optimize the hardware devices on the
system board. In addition, you can set various features such as serial console redirection, PXE
boot, and much more.
•
Initialize hardware at boot up using POST routines
During power-on or warm reset, the BIOS perform POST routines to test system components,
allocate resource for various hardware devices, and prepare the system to boot to various
operating systems.
BIOS Setup Utility
The HP server BIOS Setup Utility is used to configure five primary menu selections:
•
•
•
•
•
Main
Advanced
Boot
Security
Exit
Accessing the BIOS Setup Utility
1.
Turn on the monitor and server.
If the server is already turned on, save your data and exit from all open applications, and then
restart the server.
2.
When the HP logo is displayed during POST, press F10 into BIOS Setup Utility. If you fail to
press F10 before POST is completed, you will need to restart the server.
3.
The first page displayed is the Main menu showing the Setup Utility menu bar. Use the left (←)
and right (→) arrow keys to change the options for each setting. Use the up (↑) and down (↓)
arrow keys to move among the different settings in each menu.
Diagnostic tools and setup utilities 140
Navigating through the Setup Utility
Use the keys listed in the legend bar on the right of the Setup screen to navigate through the various
menu and submenu screens of the Setup Utility. Table 27 lists these legend keys and their respective
functions.
Table 27 Setup Utility Navigation Keys
Key
Function
← and →
Select different screens.
↑ and ↓
Select items in each menu.
Enter, Tab, or
Shift-Tab
Select a field value or display a submenu screen.
Esc
Exit the CMOS Setup menu.
<+>, <–>
Configure the system time or change field.
F1
Display more options for items marked with
To bring up the General Help window.
The General Help window describes other Setup navigation keys that are not displayed
on the legend bar.
F10
To save changes and exit the CMOS Setup Utility.
Diagnostic tools and setup utilities 141
Setup Utility menu bar
The BIOS Setup Utility provides a menu bar with the menu selections. The menu bar choices are
described in the topics below.
Main menu
Figure 130 Main Menu of the BIOS Setup Utility
ROM-based Setup Utility
<Main>
Advanced
Boot
Security
Exit
System Overview
Use [ENTER], [TAB]
Product Name:
ProLiant DL288 G6
or [SHIFT-TAB] to select a field.
ProLiant BIOS:
O20
Build Date:
01/26/2010
Use [+] or [-] to configure system
time.
ROM ID
12DIM191
Processor
Intel(R) Xeon(R) CPU
xxxxxxxxxxx
Speed:
xxxxMHz
Count:
1
System Memory
←→ Select Screen
Size:
1024MB
↑↓ Select Item
+-
Change Field
System Time
[16:52:34]
Tab Select Field
System Date
[Sat 02/14/2009]
F1
System Serial Number
General Help
F10 Save and Exit
NIC#1 MAC Address
00-21-5A-4A-11-21
NIC#2 MAC Address
00-1E-0B-4A-89-24
Asset Tag
[
POST F1 Prompt
[Delayed]
ESC Exit
]
v02. 61 (C) Copyright 1985-2006, American Megatrends, Inc.
Use this menu to configure the following items:
•
•
•
•
•
•
•
View product name.
View BIOS build date and ROM ID.
View processor information and system memory size.
Set system time and date.
View system serial number.
View NIC 1&2 MAC addresses.
Configure asset tags and POST F1 Prompt settings.
Diagnostic tools and setup utilities 142
Advanced menu
Figure 131 Advanced Menu of the BIOS Setup Utility
ROM-based Setup Utility
Main
<Advanced>
Boot
Security
Exit
Custom: Allow to
Advanced Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
configure Efficiency
/Performance related
items individually.
Efficiency
Power Efficiency Mode
Power Supply Redundancy Mode
[Efficiency]
[High Efficiency]
/Performance: Impact
groups as CPU
Configuration/CPU
bridge Configuration
> CPU Configuration
> CPU Bridge Configuration
> SATA Configuration
> SuperIO Configuration
/PCI Express
> USB Configuration
Configuration
> PCI Configuration
> PCI Express Configuration
˜˜
Select Screen
> IPMI Configuration
˜˜
Select Item
> BIOS Serial Console Configuration
Enter Go to Sub Screen
> Trusted Computing
F1
General Help
F10
Save and Exit
ESC
Exit
` Intel VT-d Configuration
V02. 61(C) Copyright 1985-2006, American Megatrends, Inc.
WARNING: Incorrect settings may cause the server to malfunction. To correct the settings, press the
F9 key to restore the default settings.
•
•
•
•
•
•
•
•
•
CPU Configuration—Configure CPU settings.
CPU Bridge Configuration—Configure CPU bridge settings.
SATA Configuration—Configure SATA settings.
SuperIO Configuration—Configure Super I/O settings.
USB Configuration—Configure USB settings.
PCI Configuration—Configure PCI settings.
PCI-Express Configuration—Configure PCI Express settings.
IPMI Configuration—Configure the IPMI settings.
BIOS Serial Console Configuration—Configure the BIOS Serial Console settings.
Diagnostic tools and setup utilities 143
Figure 132 IPMI Submenu of the BIOS Setup Utility
ROM-based Setup Utility
<Advanced>
InPut for Set LAN
IPMI 2.0 Configuration
Status of BMC
Working
BMC Firmware Revision
09.57
BMC/IPMI FW Date:
Jan/13/2010
BMC SDR Version:
2.17.0.43
Warehouse Build Number
XXX
Configuration command.
NOTE: Each question in
this group may take
considerable amount of
time.
>Set LAN Configuration
>SEL Configuration
>Hardware Health Information
>Watchdog Configuration
>Serial Port Configuration
←→ Select Screen
↑↓ Select Item
Enter Go to Sub Screen
F1
General Help
F10
Save and Exit
ESC
Exit
V02. 61(C)Copyright 1985-2006, American Megatrends, Inc.
•
•
•
•
•
•
•
•
•
Status of BMC—Display the status of BMC.
BMC Firmware Revision—Display the current revision of the BMC firmware.
BMC/IPMI FW Date—Display the date of the BMC/IPMI firmware.
BMC SDR Version—Display the current version of the BMC SDR.
Set LAN Configuration—Set LAN settings.
SEL Configuration—Display and clear the BMC system event log.
Hardware Health Information—Set temperature and fan rotation rate.
Watchdog Configuration—Configure watch dog timer status.
Serial Port Configuration—Configure serial port connection settings.
Diagnostic tools and setup utilities 144
Boot menu
Figure 133 Boot Menu of the BIOS Setup Utility
ROM-based Setup Utility
Main
Advanced
<Boot>
Security
Exit
Configure Settings
Boot Settings
during System Boot.
> Boot Settings Configuration
>Standard Boot Order
>Hard Disk Drives
USB Device Boot Priority
Restore on AC Power Loss
[High]
[Last State]
˜˜
Select Screen
˜˜
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
V02. 61 (C) Copyright 1985-2006, American Megatrends, Inc.
•
•
•
•
Boot Settings Configuration—Configure settings during system boot.
•
Restore on AC Power Loss—Use this screen to restore the AC power loss.
Standard Boot Order—View and configure standard boot order settings.
Hard Disk Drives—Display HDD information if detect HDD installed.
USB Device Boot Priority—Configure priority settings for USB devices. Users can configure the
BIOS to avoid attempting to boot non-bootable USB devices that are left plugged into the server
during POST. The options are High (default) and Low.
Diagnostic tools and setup utilities 145
Security menu
Figure 134 Security Menu of the BIOS Setup Utility
ROM-based Setup Utility
Main
Advanced
Boot
<Security>
Exit
Install or Change the
Security Settings
Admin Password:
Not Installed
User Password:
Not Installed
Password.
Change Admin Password
Boot Sector Virus Protection:
[Disabled]
˜˜
Select Screen
˜˜
Select Item
Enter Change
F1
General Help
F10 Save and Exit
ESC Exit
V02. 61(C) Copyright 1985-2006, American Megatrends, Inc.
Use this menu to configure the following items:
•
•
•
•
Admin Password—Indicate if an admin password has been installed to the system.
User Password—Indicate if a user password has been installed to the system.
Change Admin Password—Modify or change your admin password.
Boot Sector Virus Protection—Set Enabled to boot sector virus protection. The options are
Enabled and Disabled.
Diagnostic tools and setup utilities 146
Exit menu
Figure 135 Exit Menu of the BIOS Setup Utility
ROM-based Setup Utility
Main
Advanced
Boot
Security
<Exit>
Exit system setup
Exit Options
Save Changes and Exit
Discard Changes and Exit
Discard Changes
after saving the
changes.
F10 key can be used
Restore Default Settings
for this operation..
˜˜
Select Screen
˜˜
Select Item
Enter Go to Sub Screen
F1
General Help
F10 Save and Exit
ESC Exit
V02. 61(C) Copyright 1985-2006, American Megatrends, Inc.
Use this menu to save changes or discard changes. When you save and exit, the server reboots.
•
•
Save Changes and Exit—Save the changes you have made and exit the BIOS Setup Utility.
•
Discard Changes—Discard (cancel) any changes you have made. F10 can be used for this
operation. You will remain in the Setup Utility.
•
Restore Default Settings—Restore the default settings for all items in the BIOS Setup.
Discard Changes and Exit—Exit the BIOS Setup Utility without saving the changes you have
made.
Diagnostic tools and setup utilities 147
BIOS update
HP recommends that you update the server BIOS with the latest system BIOS version to take
advantage of the most recent compatibility fixes. The latest BIOS version for your server can be
downloaded from http://www.hp.com.
Clear CMOS
You may need to clear the Setup configuration values (CMOS) if the configuration has been
corrupted, or if incorrect settings made in the Setup Utility have caused error messages to be
unreadable.
To clear CMOS:
1.
Perform the Pre-installation procedure.
2.
If necessary, remove any accessory boards or cables that prevent access to the system
configuration switch.
3.
Locate the system maintenance jumper (J27-A) on the system board.
4.
Press the button. AC power must not be connected.
5.
Perform the Post-installation instructions.
6.
During POST, press F10 to access the Setup Utility.
7.
Load setup defaults by pressing F9.
8.
Set time, date, and other system values.
9.
Press F10 to close the Setup Utility.
NOTE: Clearing CMOS restore all system configurations and password default settings.
Power-On Self-Test (POST)
Before you can use a server, all devices must be tested and initialized, and the operating system must
be bootstrapped to the memory. This is referred to as Power–On Self-Test or POST. POST is a series of
diagnostic tests that checks firmware and hardware components on the system to ensure that the
server is properly functioning. This diagnostic function automatically runs each time the server is
powered on.
These diagnostics, which reside in the BIOS ROM, isolate the server-related logic failures and indicate
the board or component that you need to replace, as indicated by the error messages. Most server
hardware failures will be accurately isolated during POST. The number of tests displayed depends on
the configuration of the server.
During POST you can:
•
•
•
•
Press ESC to skip the HP logo and go to POST boot progress display system summary screen.
Press F10 to access the Setup Utility.
Press F12 to request a network boot (PXE).
Press F1 to continue POST after POST errors are detected.
Diagnostic tools and setup utilities 148
POST error indicators
When POST detects a system failure, it displays a POST error message.
POST error descriptions
When a non-fatal error occurs during POST, the screen will display an error message with the format
“xxx-Error Identifier String” where “xxx” is a unique number code that matches ODM system specific
error documentation and may be a hexadecimal or decimal value.
All Error messages describe the problems as shown below:
Table 28 POST Error Messages
Error code
Description
10
Floppy Controller Failure
00B
CMOS Memory Size Wrong
00C
RAM R/W test failed
003
CMOS Battery Low
005
CMOS Checksum Bad
040
Refresh timer test failed
041
Display memory test failed
048
Password check failed
120
$A0CCMOS Cleared by Jumper. Restore the Jumper and Continue…
122
$A0CPassword Cleared By Jumper. Restore the Jumper and Continue…
150
Processor failed BIST
160
Processor missing microcode:
192
L3 cache size mismatch
193
CPUID, Processor stepping are different
194
CPUID, Processor family are different
195
Front side bus mismatch. System halted.
196
CPUID, Processor Model are different
197
Processor speeds mismatched
198
Processor QPI speed mismatch detected.
601
Error: BMC Not Responding
605
BMC Has Detected Fatal Hardware Error
611
Internal User Area Of BMC FRU Corrupted
612
Controller Update 'boot block' Firmware Corrupted
613
Controller Operational Firmware Corrupted
Diagnostic tools and setup utilities 149
Table 28 POST Error Messages
Error code
Description
620
Non-Redundant Fan Failure or Missing
621
Redundant Fan Configuration, One Fan Failure or Missing
622
Redundant Fan Configuration, Multiple Fans Failure or Missing
Temperature Violation Detected
623
Waiting 5 minutes for system to cool
Press ESC Key to resume booting without waiting for the system to cool
Warning: Pressing ESC is NOT recommended as the system may shutdown
unexpectedly
624
Power Supply Failure or Power Supply Unplugged
626
Update SDRR/Configuration Image failed
Invalid or Unknown SKU/Chassis ID
627
Please check Front panel, System ID Jumper or Riser card
Press F1 to Continue
628
Redundant Power Supply Mismatch
701
Insufficient Runtime space for MPS data.!!.
System may operate in PIC or Non-MPS mode.
702
No enough APIC ID in range 0-0Fh can be assigned to IO APICs.
(Re-assigning CPUs' local APIC ID may solve this issue)
MPS Table is not built! System may operate in PIC or Non-MPS mode.
POST related troubleshooting
Perform the following procedures when POST fails to run, displays error messages.
If the POST failure is during a routine boot up, check the following:
•
•
•
All external cables and power cables should be firmly plugged in.
•
•
•
•
•
•
The monitor's contrast and brightness settings are correct.
•
•
All internal cabling and connections are in their proper order.
The power outlet to the server should be connected and works correctly.
The server and monitor are both turned on. The bicolour status LED indicator on the front panel
must be lit up green.
All internal cables are properly connected and all boards firmly seated.
The processor is fully seated in its socket on the system board.
The heat sink assembly is properly installed on top of the processor.
All memory modules are properly installed.
If you have installed a PCI accessory board, verify that the board is firmly seated and any
jumpers on the board are properly set. Refer to the documentation provided with the accessory
board.
If you have changed the jumpers on the system board, verify that each is properly set.
Diagnostic tools and setup utilities 150
SETSYS utility
SETSYS.EXE (DOS application) is the correct tool for setting the Serial Number/Asset Tag text on this
server after a system board replacement has occurred.
Once the Serial Number/Asset Tag text has been entered via SETSYS, populating the SMBIOS data,
the system BIOS will automatically write this info into the BMC IPMI FRU data on the next boot up.
Diagnostic tools and setup utilities 151
Physical and operating specifications
This chapter provides physical and operating specifications for the HP ProLiant DL288 G6 server.
Specifications include:
System unit
Table 29 Hardware Specifications
Item
Components
Processor socket
Intel FCLGA1366 socket
Processor
2P Intel Xeon processor 5500 series with integrated memory
controller
2P Intel Xeon processor 5600 series with integrated memory
controller
Chipset
Tylersberg-36D/ICH-10R
Hardware monitoring device
ServerEngines Pilot 2 management controller
Gigabit ethernet controller
HP NC362i GbE controller for NIC
LO100i sideband support
Onboard storage controller
Integrated ICH10R SATA (6-port)
ODD & Floppy interface
Optional Optical Disc Drive (SATA)
Optional Floppy (USB only, USB key)
Embedded video controller
ServerEngines Pilot 2 management controller
I/O subsystem
One PCIe x16 links with x16 slot + PCIe x4 links with x4 slot
One PCIe x16 links with x16 slot
Memory
Twelve DDR3 800/1066/1333 MHz RDIMM/UDIMM slots, up to
96 GB
Default media storage
Four bays hot-plug HDD cage for 3.5” SAS or SATA drivers
Eight bays hot-plug HDD cage for 3.5” SAS or SATA drives
Eight bays hot-plug HDD cage for 2.5” SAS or SATA drives
Twelve bays hot-plug HDD cage for 3.5” SAS or SATA drives
Twenty-five bays hot-plug HDD cage for 2.5” SAS or SATA drives
Optical disc drive
One slim optical disc drive bay for optical disc drive on the front (8
3.5” HDD model)
I/O ports
PS/2 keyboard port, PS/2 mouse port, USB 2.0 ports (two rear
USB ports, one internal USB port, two front USB ports), video port,
serial port and GbE port and IPMI LAN port.
Physical and operating specifications
152
Table 29 Hardware Specifications
Item
Components
Status LED indicators
Front panel
System Health LED
NIC 1/2 activity LED
Power Switch/LED
Hard drive activity LED indicator
UID Switch/LED
Rear panel
UID LED
LAN link status
System board
BMC Activity LED
Power supply unit
460 W redundant, power supply
750 W redundant, power supply
Thermal solution
Four system fans
Or eight system fans
Physical and operating specifications
153
Table 30 Physical Dimensions
Item
Description
System board platform
EATX (Extended Advanced Technology Extended)
System board dimension
304.8 mm x 330.2 mm (12 in x 13 in)
Server dimensions (H x W x D)
Rack
87.6 mm x 448.0 mm x 703.4 mm (3.45 in x 17.64 in x
27.69 in)
Server weight
Basic configuration (excludes monitor): 16~24kg
Table 31 Environmental Specifications
Item
Description
Temperature:
Operating
+10°C to +35°C (+50°F to +95°F)
Non-operating
-30°C to 60°C (-22°F to 140°F)
Storage
-30°C to 60°C (-22°F to 140°F)
Wet-bulb temperature
38.7°C (101.7°F)
Relative humidity:
Operating
10% to 90% (non-condensing)
Non-operating
5% to 95%
Storage
5% to 95%
Altitude:
Operating
0 to 3049 m (0 to 10,000 ft)
Non-operating
0 to 9146 m (0 to 30,000 ft)
Thermal output (maximum operating)
1000 W/hr
Acoustic emissions
LWad: 6.7 Bels
Normal configuration
(operating at room temperature)
LWad: 6.7 Bels
(Idle at room temperature)
Physical and operating specifications
154
Table 32 Power Supply Specifications / 460 W
Item
Description
Dimensions (H x W x D)
38.5 mm x 86.4 mm x 190.5 mm (1.52 in x 3.4 in x 7.5 in)
Weight (approximate)
1.36 kg
Input requirements:
Rated input voltage
90 VAC to 264 VAC
Normal line voltage
100 VAC to 120 VAC/200 VAC to 240 VAC
Line frequency
47–63 Hz
Rated input current
6.0 ARMS max @ 100 V
5.0 ARMS max @ 120 V
3.00 ARMS max @ 200 V to 240 V
BTU rating
N/A
Power supply output power:
Rated steady state power
460 W (1+1 Redundant)
Maximum peak power
N/A
Temperature range:
Operating
+5°C to +50°C
Shipping
–40°C to +85°C
Relative humidity:
Operating
5% to 95% relative humidity, non-condensing
Non-operating
5% to 95% relative humidity, non-condensing
Table 33 Power Supply Specifications / 750 W
Item
Description
Dimensions (H x W x D)
38.5 mm x 86.4 mm x 190.5 mm (1.52 in x 3.4 in x 7.5 in)
Weight (approximate)
1.36 kg
Input requirements:
Rated input voltage
90 VAC to 264 VAC
Normal line voltage
100 VAC to 120 VAC/200 VAC to 240 VAC
Line frequency
47–63 Hz
Rated input current
9.10 ARMS max @ 100V
5.10 ARMS max @ 200V
BTU rating
N/A
Power supply output power:
Rated steady state power
750 W (1+1 Redundant)
Maximum peak power
N/A
Physical and operating specifications
155
Table 33 Power Supply Specifications / 750 W
Item
Description
Temperature range:
Operating
+5°C to +50°C
Shipping
–40°C to +85°C
Relative humidity:
Operating
5% to 95% relative humidity, non-condensing
Non-operating
5% to 95% relative humidity, non-condensing
Physical and operating specifications
156
Index
POST, 148
A
AC power
power-down procedures, 42
air baffle
installing, 79
Diagnostic tools and Setup Utilities
clear CMOS, 148
drive bay configuration, 49
drives
backplane, 61
removing, 71
cable connections, 45
B
cable management, 44
backplane, 61
drive bay configuration, 49
reinstalling, 68
hard drives, 55
removing, 68
battery
replacement warnings, 108
BBWC
Optical disc drive, 52
E
electric shock
symbol, 41
reinstalling, 111
removing, 110
bezel blank
removing, 53
warning, 40
environmental specifications, 154
exploded view
Mechanical Components Spare Parts List / 12 3.5, 15
BIOS Setup Utility
Mechanical Components Spare Parts List / 25 2.5, 16
accessing, 140
Mechanical Components Spare Parts List / 8 2.5, 14
additional navigation keys, 141
Mechanical Components Spare Parts List / 8 3.5, 13
menu bar, 140
System Components Spare Parts List / 12 3.5, 30
BIOS software
System Components Spare Parts List / 4 3.5, 21
overview, 140
System Components Spare Parts List / 8 2.5, 27
C
System Components Spare Parts List / 8 3.5, 24
cable connections, 45
cable management, 44
CSR (customer self repair), 1
CSR program
System Components Spare Parts List /25 2.5, 33
F
front panel components, 125
part categories, 2
H
website, 1
hard drive
customer self repair (CSR), 1
installing, 60
D
removing, 60
dedicated management port
reinstalling, 104, 106
removing, 103, 105
diagnostic tools and setup utilities
BIOS Setup Utility, 140
BIOS software, 140
BIOS update, 148
hard drive cage for 12 3.5, 15
hard drive cage for 25 2.5, 16
hard drive cage for 4 3.5, 12
hard drive cage for 8 2.5, 14
hard drive cage for 8 3.5, 13
Hard drive LED indicators, 137
hardware configuration
BBWC, 110
Index 157
dedicated management port, 102, 105
L
hard drives, 55
LAN controller, 152
memory, 79
LED indicator
Optical disc drive, 52
optical disc drive activity, 136
PCI expansion card, 83
power supply unit, 114
system board LED, 139
LED indicators
processor, 70
references, 39
system battery, 107
system fan, 122
system fan cage, 117
top cover, 43
hardware configuration tools, 39
hardware specifications
I/O ports, 152
LAN, 138
M
mechanical components / 12 3.5, 15
mechanical components / 25 2.5, 16
mechanical components / 4 3.5, 12
mechanical components / 8 2.5, 14
mechanical components / 8 3.5, 13
memory module
installing, 81
LAN controller, 152
memory, 152
processor socket, 152
removing, 81
memory modules
spare part number, 21, 24, 25, 27, 28, 30, 31, 33,
34
processor support, 152
status LED indicators, 153
thermal solution, 153
Hardware Specifications, 152
O
onboard controllers
LAN, 152
chipset, 152
default media storage, 152
Hardware monitoring device, 152
I/O subsystem, 152
optical media storage, 152
storage controller, 152
optical carrier
installing, 54
optical disc drive
activity indicator, 136
hazardous conditions. See symbols on equipment
hazardous energy circuits
symbol, 41
heat sink
installing, 78
removing, 71
hot surface
symbol, 41
warning, 40
HP
authorized reseller, 37
contact information, 37
technical support, 37
technical support requirements, 37
I
improper airflow
caution, 40
removing, 52
P
PCI cage
reinstalling, 95, 97, 99
removing, 87
PCI card
installing, 92
PCI riser card expansion slot, 84
PCIe riser card
installing, 87, 90
removing, 88
physical dimensions, 154
server, 154
system board, 154
Power Supply Specifications / 460 W, 155
Power Supply Specifications / 750 W, 155
power supply unit. See PSU
Power-On Self Test
Index 158
POST error indicators, 149
reinstalling, 113
POST related troubleshooting, 150
removing, 112
recoverable POST errors, 149
spare part number, 21, 24, 27, 30, 33
SETSYS utility, 151
processor
system components / 12 3.5, 30
system components / 25 2.5, 33
applying thermal grease compound, 74
system components / 4 3.5, 20
removing, 72
system components / 8 2.5, 27
processor socket
system components / 8 3.5, 24
specification, 152
system cover
processors
spare part number, 21, 25, 28, 31, 34
top cover, 43
system fan
PSU
installing, 124
reinstalling, 115
removing, 114
removing, 123
system fans
replacement warnings, 114
R
rear panel components, 130
S
SAS/SATA hard drives with carriers
spare part number, 22, 23, 25, 26, 29, 31, 32, 34,
35
server dimensions
spare part number, 21, 23, 24, 26, 27, 29, 30, 32,
33, 35
system LEDs. See status LEDs
system non-redundant fan cage
reinstalling, 118
system non-redundant fan cage
removing, 118
system redundant fan cage
installing, 119
rack, 154
server warnings and cautions, 40
Setup Utility menu bar
removing, 118
system structure
front panel, 125
advanced menu, 143
rear panel, 130
boot menu, 145
exit menu, 147
security menu, 146
specifications
physical and operating, 152
system board, 133
T
thermal solution, 153
top cover
reinstalling, 43
storage controller, 152
removing, 43
symbols on equipment, 41
spare part number, 12, 13, 14, 15, 16
system battery
replacing, 108
system board
W
warnings
components, 133
battery replacement, 108
dimensions, 154
PSU replacement, 114
LED, 139
warranty, 1
platform, 154
Index 159
Download PDF

advertising