HP 2510xi Installation guide

HP 2510xi Installation guide
Q3093-90172
a Choose the one poster that
b
matches your equipment.
If you have an existing
Windows or Macintosh
Network setup, follow this
poster.
Wired Network
4
2
Remove all items
from the carton.
Remove all tape
and packaging
from the
HP PSC.
3
Remove tray and load plain white paper
a Place the cover over
the top of the
HP PSC. Make sure
the buttons are
visible.
b Firmly press down
Wireless Network
5
a
a
c
b
b
a
b
c
d
Lift display.
c
Connect power cords
Connect the power
supply to the
HP PSC, and then to
the power cord.
Plug into the wall.
Attach cover and lift display
on all sides of the
cover.
If you do not have a network,
see the Direct Connect(USB)
poster.
Connect supplied phone cord
6
You must connect one end of the
supplied phone cord to the phone jack
on the left (1-LINE) and the other end
to a wall jack.
Turn on and set language
and country/region
a
Turn power on.
b
Select your language, and then press
OK. Select your country/region, and
then press OK.
To connect an answering machine or
use your own phone cord, see the
Fax Setup chapter in the
Reference Guide.
1-LINE
hp psc 2500 photosmart series all-in-one
Windows/Macintosh
Network (Wired/Wireless) Setup Poster - Side 1
*Q3093-90172*
*Q3093-90172*
Wired/Wireless Network
Start Here - CHOOSE CORRECT POSTER
1
7
8
Insert print cartridges
Tri-Color
a
9
Lift the print carriage door
up until it catches. Lift the
blue and gray latches.
b
Remove the bright pink
tape from both the print
cartridges. Do not touch
the gold-colored contacts
or retape the cartridges.
c
d
Hold the black print cartridge with the label on top as
shown. Slide the cartridge underneath the metal bar
into the right (gray latch) side of the print carriage.
e
Hold the color print cartridge with the label on top
as shown. Slide the cartridge into the left (blue
latch) side of the print carriage.
Pull the end of the gray latch
toward you, press down until it
stops, and then release. Make
sure the latch catches below the
bottom tabs. Repeat with the
blue latch.
f
Align the print cartridges
Black
Make sure both latches are
locked into position. Close
the door.
Press OK on the front panel to begin
alignment. Wait a couple of minutes.
After a page prints, alignment is
complete. Discard or recycle this
page.
Choose Wired or Wireless setup*
Match the network type to your
existing network.
If you do not have an existing
network, set one up before
attempting to connect the
HP PSC.
Choose a or b, and then turn the
poster over.
a
Wired network
Requirements:
Router/hub/switch
ETHERNET (CAT-5) cable
Go to step 10a to set up with a wired network.
bc
Wireless network (infrastructure)
Requirements:
Wireless access point/
gateway/base station
ETHERNET (CAT-5) cable
*If you have a different network
setup, see the Reference Guide.
Wireless Information:
WPA - If your wireless network uses WPA, configure this on the
HP PSC before you install the software. For details see the
Reference Guide, chapter 15, Wireless Network Setup,
use the embedded web server.
To set up with a USB cable, please
see the other poster for a direct
connection (install the software
before connecting the USB cable).
Compatibility with 802.11g - This HP PSC includes an 802.11b
radio that is compatible on 802.11g systems.
Go to step 10b to set up with a wireless network.
Copyright Hewlett-Packard Company 2003 Printed in Germany.
For the most up-to-date information on network setup, see www. hp.com/support
Side 2 - Start on other side.
10a Wired network setup
Follow these boxed steps for each computer that is part of the wired network.
WINDOWS
USERS:
Wired setup allows your
HP PSC to communicate to
your computers through a
router/hub/switch.
1
2
4
3
Choose
Windows or
Macintosh,
and then follow
the steps carefully.
8
9
10
11
Complete the rest of
the onscreen
instructions.
After your computer
restarts, follow all
onscreen instructions
including the Fax
Setup Wizard.
Congratulations!
You are ready
to use the HP PSC.
5
6
7
Turn on your
computer and wait
for the desktop to
appear.
Insert the HP PSC
Windows CD and
then, follow the
onscreen
instructions.
Choose Through the
network as your
connection type.
6
7
8
9
1010
Insert the HP PSC
Macintosh CD.
Double-click the HP
In the first dialog
box, you must select
Network as the
device connection
type.
Choose wired
network as your
connection type.
Complete all onscreen
instructions including
the Setup Assistant.
In the Select Device
dialog box, make
sure TCP/IP
(network) is
selected.
Choose the second
option, connect
using a network
cable as your
connection type.
Make sure you are
logged onto the
network.
Disable any firewall
software.
ETHERNET
Connect the
ETHERNET
cable to the
hub/router/
switch.
Remove the yellow
plug from the
ETHERNET jack.
Connect the
ETHERNET cable to
the back of the
HP PSC.
hp psc 2500
photosmart series
all-in-one
reference guide
If you have any questions,
see the Wired Network
Setup chapter in the
Reference Guide.
MACINTOSH
USERS:
STOP! Make sure
the blue network
light on the HP PSC
is lit. This might take
60 seconds.
5
Turn on your
computer and wait
for the desktop to
appear.
All-In-One Installer
icon on your folder.
Make sure you are
logged onto the
network.
NOTE: You can use the
cable from the box or
purchase a longer cable.
1111
Congratulations!
You are ready
to use the
HP PSC.
Disable any
firewall software.
Network Setup Poster - Side 2
10b Wireless network setup (infrastructure)
Follow these boxed steps for each computer that is part of the wireless network.
Wireless setup allows your
HP PSC to communicate to your
computers through a wireless
access point or base station.
WINDOWS
USERS:
1
2
3
ETHERNET
Remove the yellow
plug from the
ETHERNET jack.
Connect the
ETHERNET cable to
the back of the
HP PSC.
Connect the
ETHERNET
cable to the
access point.
(You will remove
this later.)
STOP! Make sure
the blue network
light on the
HP PSC is lit. This
might take 60
seconds.
4
5
In the box below,
write down the
information listed.
Use during step
10. If you are
unsure, see the
documentation or
web page for the
access point/base
station.
Choose
Windows or
Macintosh,
and then follow
the steps carefully.
SSID
/Network Name:
WEP Key/Password
(if applicable):
For Macintosh, this is
called Network Name
and Password.
6
7
Turn on your
computer and wait
for the desktop to
appear.
Insert the HP PSC
Windows CD and
then, follow the
onscreen
instructions.
8
Choose Through
the network as
your connection
type.
9
10
11
12
Choose connect
Complete the rest of
the onscreen
instructions. Enter the
information your
wrote down earlier.
When you see the
After your
computer restarts,
complete all
onscreen
instructions
including the Fax
Setup Wizard.
using wireless
communication
as your connection
type.
Make sure you are
logged onto the
network.
Make sure the blue
network light is
steady. Refer to the
Reference Guide for
help.
Disable any
firewall software.
Unplug Cable
dialog box,
disconnect the
cable from your
HP PSC and
access point.
Congratulations!
You are ready
to use the HP PSC.
12
MACINTOSH
USERS:
6
7
Turn on your
computer and wait
for the desktop to
appear.
Insert the HP PSC
Macintosh CD.
Make sure you are
logged onto the
network.
Disable any
firewall software.
Double-click the
HP All-In-One
Installer icon on
8
In the first dialog
box, you must select
Network as the
device connection
type.
9
Choose wireless
network as your
connection type.
1010
Enter the
information that
you wrote down
earlier.
Make sure the
blue network light
is steady. Refer to
the Reference
Guide for help.
1111
Complete all
onscreen
instructions
including the
Setup Assistant. In
the Select Device
dialog box, make
sure
TCP/IP
(network) is
selected.
12
Congratulations!
You are ready
to use the HP PSC.
your desktop.
hp psc 2500
photosmart series
all-in-one
reference guide
If you have any questions,
see the Wireless
Network Setup chapter
in the Reference Guide.
For the most up-to-date information on network setup, see www. hp.com/support
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement