HP | StorageWorks Disk System 2100 (fld rck 0 drvs) | User's Manual | HP StorageWorks Disk System 2100 (fld rck 0 drvs) User's Manual

HP StorageWorks
Disk System 2100 / 2110
User’s Guide
Edition E0304
Order No. A7381-96013
Printed in U.S.A.
Components bearing this symbol may
be hot to touch.
Notice
© Hewlett-Packard Company, 2004. All rights
reserved.
Hewlett-Packard Company makes no warranty of
any kind with regard to this document, including, but
not limited to, the implied warranties of merchantability and fitness for a particular purpose. HewlettPackard shall not be liable for errors contained
herein or for incidental or consequential damages in
connection with the furnishing, performance, or use
of this material.
This document contains proprietary information,
which is protected by copyright. No part of this
document may be photocopied, reproduced, or
translated into another language without the prior
written consent of Hewlett-Packard. The information contained in this document is subject to change
without notice.
Warranty
If you have any questions about the warranty for
this product, contact your dealer or local HewlettPackard sales representative.
Components bearing this symbol are
fragile. Handle with care.
Components bearing this symbol are
susceptible to damage by static
electricity. ESD precautions are
required.
Operation
The front door should be closed and locked at all
times during the operation of this product except
when replacing disks.
This product is intended to be operated in a
restricted access area.
Service
Maintenance or repair of the backplane and
mezzanine boards must be performed by authorized
service-trained personnel.
Format Conventions
Denotes
WARNING
Safety Notices
Warning
CAUTION
Weight exceeds 50 lbs. (22.5 kg.)
Do NOT lift unassisted. Use
a lift device or two people.
A hazard that can cause hardware
or software damage
Note
Significant concepts or operating
instructions
this font
Text to be typed verbatim: all
commands, path names, and file
names. Also menu and button
selections in GUI contexts
this font
Text displayed on the screen
To protect against personal injury and product
damage, do not attempt to lift the product without
the assistance of another person or lift device.
2
A hazard that can cause
personal injury
Table of Contents
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Components of the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Disk Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Power LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
SCSI ID Switch. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Connector. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Electrical Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
AC Site Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Installing the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Hardware Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Preparing for Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Setting the SCSI IDs for the Disk Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Installing the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connect the SCSI Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Connecting the Power Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Powering On and Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power On the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Power Off the Disk System. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Adding Disk Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Add a Disk Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Configure the new Disk Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Remove and Replace A Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . 19
Remove a Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Replace a Disk Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Remove the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Setting Up the Hardware Event Monitor (HP-UX Only) . . . . . . . . . . . 22
Configuration Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Event Notification (HP-UX Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Status LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
View Disk Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
STM Disk Information: HP-UX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
STM Disk Information: MPE/iX 6.5 or Later . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Isolating Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Reference Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Product Numbers and Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Upgrade Disk Products Available. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Electrical Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Operating Temperatures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
3
4
Table of Contents
Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Safety Certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
EMC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
A. FCC Notice for United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
B. Canadian Notice (Avis Canadien) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
C. Notice for European Union . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
D. Notice for France . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
E. Notice for Japan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
F. Harmonics Conformance (Japan) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
G. BSMI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
H. Notice for Germany . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
I. Declaration of Conformity. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Product Web Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
List of Figures
Figure 1
Disk Module LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Figure 2
System Power LED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 3
Rear View of the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4
Power Button . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 5
SCSI ID Switch Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6
AC Power Connector Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7
SCSI Switch Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Figure 8
SCSI Port Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Figure 9
AC Power Connector Location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Figure 10
Power Button Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 11
Installing a Disk Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 12
Removing the Disk System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 13
Sample Hardware Event Notification. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 14
LED Status Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 15
Sample STM Information Log (HP-UX) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 16
Sample STM Expert Tool Disk Error Log (MPE/iX 6.5 or Later). . . . . . . . . . . . . . . . . . . . . . 29
5
6
List of Tables
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
Table
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Disk LED Activity Definitions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
System Power LED Activity Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AC Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
SCSI Switch Setting Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
SCSI Address Priority. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
LED Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Troubleshooting Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Product Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Available Upgrade Disk Modules . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Upgrade Products for Hewlett-Packard Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Replaceable Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Supported HP Cables and Terminators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Physical Dimensions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
AC Power Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Environmental Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
HP StorageWorks Disk System 2100 / 2110
7
Overview
Both units support Ultra3 (U160) drives and the new U320 drives. However, the U320
drives are supported at a maximum of 160 MB/s speeds. The Disk System 2100 does
not support the U320 73-GB drive (part number A7286A) or the U320 146-GB drive
(part number A7287A).
For both the DS2100 and DS2110, connectivity to U320 initiators is supported if the
speed of the U320 initiator is set to limit negotiations to U160 speed. The U320 drives
do not operate reliably at U320 speeds and are not supported at those speeds. This is
due to limitations within the controller and not the U320 drive mechanisms.
English
The HP StorageWorks Disk System 2100 and Disk System 2110 are 1-EIA unit disk
systems capable of accommodating up to four disk modules. They are designed to
provide inexpensive, high performance rack-optimized online mass storage for entrylevel configurations in three distinct markets: (1) HP servers/workstations, (2) open
systems JBODs, and (3) open systems IDACs (Internal Disk Array Controller).
8
HP StorageWorks Disk System 2100 / 2110
Components of the Disk System
Front Panel
The disk modules can be accessed from the front of the disk system. It can accept up
to 4 low profile disk drives. If your storage system contains less than 4 disk modules,
the remaining empty slots contain filler panels. These filler panels (part number
A6198-60002) ensure that the proper cooling is maintained within the storage system.
Remove filler panels only when a disk module is added to the system.
Disk Module LEDs
Each disk module has two LEDs: an amber LED on the top (see Figure 1) and a green
LED on the bottom. The amber LED is not operational. The green LED provides disk
module status information as listed in Table 6.
FIGURE 1
Disk Module LEDs
Amber LED (not used)
Green LED
Disk Module
LEDs
TABLE 1
Disk LED Activity Definitions
LED Activity
Indication
Blinking
Disk activity
On solid for
approximately 1 second
Bus reset
Off
Disk is idle or off
System Power LED
The System Power LED (see Figure 2) gives diagnostic information about the disk
system operation. Refer to Table 2 on page 9 for more information.
HP StorageWorks Disk System 2100 / 2110
FIGURE 2
9
System Power LED
English
System
Power LED
TABLE 2
System Power LED Activity Definitions
LED Activity
Indication
Blinking
Malfunction - either a fan is not operating
properly or internal voltage is too low.
On solid
Disk system is operating properly.
Off
Disk system is off.
Rear Panel
FIGURE 3
Rear View of the Disk System
AC
Power
Connector
FIGURE 4
SCSI
Address
Switch
Power
Button
LVD/SE
SCSI
Port
LVD/SE
SCSI
Port
Power Button
Power
Button
With the power button in the “ON” position, power is supplied to the disk system.
10
HP StorageWorks Disk System 2100 / 2110
SCSI ID Switch
The SCSI ID switch sets the address for the disk drives.
There are three possible settings for the SCSI address switch: A, B, and C. Each
setting assigns a different set of addresses to the disk modules installed in the disk
system. For SCSI address switch setting A, the addresses for the installed disk
modules are (from left to right, looking at the disk system from the front) 0, 2, 4, and
6. For SCSI address switch setting B, the addresses for the installed disk modules are
8, 10, 12, and 14. For SCSI address switch setting C, the addresses for the installed
disk modules are 9, 11, 13, and 15. See Figure 5, below.
SCSI address 7 is reserved for use by the host bus adapter.
FIGURE 5
SCSI ID Switch Settings
C
B
A
SCSI
Address
Switch
Setting
A
B
C
Disk Module SCSI Addresses (Viewed from front of storage enclosure)
0
8
9
2
10
11
4
12
13
6
14
15
Note The disk system requires a terminator when it is installed at the end
of the SCSI bus.
HP StorageWorks Disk System 2100 / 2110
11
Power Connector
FIGURE 6
AC Power Connector Location
English
AC
Power
Connector
Electrical Requirements
AC Site Requirements
Overcurrent protection devices are required for each cabinet where the disk system is
installed. They must be positioned between the power source and the disk system.
These protective devices must not trip when exposed to an inrush current of 30 amps
lasting 5 ms.
Note These protection devices must meet all applicable electrical safety
requirements and be approved for the intended purpose.
I
TABLE 3
AC Power Requirements
Electrical Element
Requirements
Voltage
100-240 VAC
Frequency
50-60 Hz
Input Current
< 1 amp
Maximum Surge Current
30 amps peak
12
HP StorageWorks Disk System 2100 / 2110
Installing the Disk System
Hardware Requirements
The following hardware is included with the disk system:
One power cord comes with each disk system.
Your host computer must have one of the following:
■
An on board UltraSCSI port
■
An UltraSCSI host bus adapter board installed in the host system:
– A6828A Single Port Ultra160 SCSI Host Bus Adapter (HP Series 9000 only)
– A6829A Dual Port Ultra160 SCSI Host Bus Adapter (HP Series 9000 only)
– A7059A Windows and Linux Ultra160 SCSI Host Bus Adapter
– A7060A Windows and Linux Dual Port Ultra160 SCSI Host Bus Adapter
– P3413A Single Port Ultra3 SCSI Host Bus Adapter for HP Netservers
The following accessories are available for your storage disk system:
■
A6828A Single Port Ultra160 SCSI Host Bus Adapter
■
A6829A Dual Port Ultra160 SCSI Host Bus Adapter
■
C2364A High Density 68-pin Terminator for LVD or Single-Ended
The DS2100 and DS2110 support a maximum SCSI speed of U160. Connectivity to
U320 initiators is supported if the speed of the U320 initiator is set to limit
negotiations to U160 speed. U320 drives do not operate reliably at U320 speeds and
are not supported at those speeds. This is due to limitations within the controller and
not the U320 disk mechanisms. Contact your HP support representative for assistance
with the configuration.
Preparing for Installation
Before the disk system is ready for installation, its SCSI IDs must be set and the host
system must be prepared to recognize the newly installed disk system. See your
operating system administration manual for configuration procedures for the host bus
adapter.
HP StorageWorks Disk System 2100 / 2110
13
Setting the SCSI IDs for the Disk Modules
1 Determine which SCSI addresses are not being used on the host system.
2 Locate the SCSI switch on the back of the disk system.
FIGURE 7
SCSI Switch Location
C
B
A
SCSI
Address
Switch
Setting
A
B
C
Disk Module SCSI Addresses (Viewed from front of storage enclosure)
6
14
15
4
12
13
2
10
11
0
8
9
3 Set the SCSI IDs.
Verify that the SCSI IDs you have chosen are available. If you are daisy-chaining
these disk systems together, each SCSI ID switch must be set for a unique
available set of SCSI IDs.
TABLE 4
SCSI Switch Setting Definitions
SCSI
Switch
Setting
Disk Slot
1
2
3
4
A
0
2
4
6
B
8
10
12
14
C
9
11
13
15
English
Refer to your system administration manual for information on determining
which SCSI addresses are available on the host system.
14
HP StorageWorks Disk System 2100 / 2110
Keep in mind that the host bus adapter should have the highest SCSI address priority.
See Table 5 below.
TABLE 5
SCSI Address Priority
SCSI ID 7
Priority
6
5
4
3
2
1
0
15
14
13
12
Highest
11
10
9
8
Lowest
Installing the Disk System
See the installation instructions enclosed with your rackmount kit.
Connect the SCSI Cables
1 Make sure that the host system has been powered down.
2 Connect one end of an Ultra SCSI cable (included in the shipping box) to the host
system. For the SCSI port location on your host system, refer to your host system’s
documentation.
3 Connect the other end of the SCSI cable to one of the LVD/SE ports on the rear of
the disk system.
FIGURE 8
SCSI Port Locations
LVD/SE
SCSI
Port
LVD/SE
SCSI
Port
HP StorageWorks Disk System 2100 / 2110
15
4 Determine if this disk system is at the beginning or end of the SCSI bus.
– If the disk system is at the beginning or middle of the SCSI bus (you are going
to daisy-chain another device off this one), consider the following:
• Due to SCSI ID restrictions, no more than three of these disk systems can be
daisy-chained together.
• For the DS2110, use only 0.5-meter cable between enclosures in daisy-chain
configurations. Longer cable lengths between enclosures are not supported.
• Ensure that the SCSI IDs assigned for the disk drives in the second disk
system or other peripheral are not already assigned to another device on the
SCSI bus. Refer to “Setting the SCSI IDs for the Disk Modules” (see Figure 7
on page 13 for the SCSI IDs assigned for each SCSI switch setting).
• If you connected the SCSI cable to the on-board UltraSCSI port on the host
system, verify that the SCSI IDs assigned to the disk drives in the second disk
system or additional peripherals are not already assigned to any other
peripherals installed in the host system.
• For the DS2100, the overall SCSI bus length cannot exceed
12 meters. For the DS2110, the overall SCSI bus length cannot exceed 9
meters.
The SCSI bus length for the disk system internal cables is 1.1 meters. If
another type of peripheral is being connected on this SCSI bus, refer to that
peripheral’s documentation for its internal SCSI cable length.
5 Connect one end of an Ultra SCSI cable (get it from the shipping box) to the
available SCSI port on the rear of the first disk system on the SCSI bus.
6 Connect the other end of the Ultra SCSI cable to the SCSI IN port on the rear of
the second disk system on the SCSI bus.
7 Repeat Steps 3, 5, and 6 for the last disk system on the SCSI bus if three disk
systems are being installed. Keep in mind the maximum bus length (12 meters).
8 Install a terminator if the device is the last one on the bus. For supported
terminators, see Table 10 on page 33 or Table 12 on page 34.
Note The disk system, when connected at the end of a SCSI bus, requires
a terminator. Refer to the documentation that came with your wide
SCSI device to determine if it needs a terminator or not. Narrow
SCSI devices at the end of a daisy-chain always require a terminator.
English
– If the disk system is at the end of the SCSI bus (you are not going to daisy-chain
another device off this one), install the appropriate terminator (part number
5183-2657) on the available SCSI port and go to “Connecting the Power Cable”
(see Figure 9 on page 16).
16
HP StorageWorks Disk System 2100 / 2110
Connecting the Power Cable
CAUTION
FIGURE 9
Ensure that the connection of multiple units to the supply circuit does not
overload the supply overcurrent protection or the supply wiring. Refer to
the storage electrical ratings when determining the correct branch circuit
rating for your installation. See Table 3 on page 11.
AC Power Connector Location
AC
Power
Connector
Powering On and Off
Power On the Disk System
1 Press the power button and release it. The power button will stay in a depressed
position, indicating that the power is on.
See Figure 10 on page 17 for the location of the power button.
2 Confirm that the disk system is running properly by checking the system power
LED and the disk module LEDs at the front of your disk system. A system reboot
may be necessary to assure that the host system recognizes the disk drives within
the disk system.
Refer to “Front Panel” on page 3 for explanations of the LED functions and their
meanings.
HP StorageWorks Disk System 2100 / 2110
17
Power Off the Disk System
1 Back up all data if the disk system is still operational.
3 Unmount any file systems associated with the disk system that is going to be
powered off. Refer to the system administration manual for your host system’s
operating system for the correct procedure for unmounting a file system or
stopping access to the disk modules within the disk system.
Note If your host system’s boot or root disk drive resides in the disk
system, the host system must be brought down before the power
to the disk system can be turned off. See your host system’s
system administrator’s manual for the correct procedures.
4 Turn the disk system off by pressing the power button. See Figure 10 (below) for
the power button location.
5 Confirm that the storage disk system System Power LED is off. See Figure 2 on
page 9.
6 Disconnect the power cable from the power connector at the rear of the disk
system.
FIGURE 10 Power Button Location
Power
Button
English
2 Ensure that no data on disk modules within the disk system is being accessed.
18
HP StorageWorks Disk System 2100 / 2110
Adding Disk Modules
Disk modules can be added, removed, and replaced while the disk system is running.
Because the disk modules can be handled in this way, they are called
hot-pluggable.
The SCSI addresses for the disks are set using the addressing switches on the back of
the disk system. You can determine the assigned SCSI addresses by looking at the
SCSI address switch settings at the rear of the disk system.
If your storage system contains less than 4 disk modules, the remaining empty slots
require filler panels. These filler panels ensure that the proper cooling is maintained
within the storage system.
The system administration procedure for adding a disk module is operating system
specific. You must decide where the disk module is to be installed and install it. Once
the disk module is installed, the operating system must be configured to recognize it.
Add a Disk Module
1 Select an available slot for the new disk module. Note the slot chosen for
application configuration.
2 Remove the disk module filler panel. Store the filler panel for future use.
3 Hold the locking handle open on the disk drive. Push the locking lever to the left
to release the latch.
4 Slide the disk into the appropriate slot.
5 Gently push the drive until the locking mechanism engages. When the disk
module is completely installed, an audible click can be heard.
6 Close the locking handle completely, using gentle downward pressure.
HP StorageWorks Disk System 2100 / 2110
19
FIGURE 11 Installing a Disk Module
English
Configure the new Disk Module
Configure a new disk module within your application.
CAUTION
These procedures should be performed only by qualified system
administrator. Performing hot-plug operations on an active disk drive can
result in data loss or corruption.
Remove and Replace A Disk Module
Remove a Disk Module
CAUTION
If the disk system is running and a disk module slot does not contain a disk
drive or filler panel, the disk system will not cool properly and may
overheat. If you are not replacing the disk module immediately, a filler
panel must be installed to maintain proper cooling.
Ensure that you have a replacement disk or filler panel before removing the
disk module from the disk system unless you are returning a defective disk
system.
1 Ensure there is no activity on the drives.
If the Disk Drive LED for that disk module is flashing green, the disk drive is
active. When the Disk Drive LED off, the disk module is either idle or
completely off (see Table 1 on page 8). In this state, it is safe to remove the disk
module.
20
HP StorageWorks Disk System 2100 / 2110
2 Prepare the software environment to remove the drive.
See your operating system documentation for instructions and procedures
required to remove a disk module. It may be necessary to unmount file systems
associated with the disk drives installed in the disk system.
3 Unlatch the disk module handle and remove the disk module.
Squeeze the latch to unlock the disk module. Put a finger behind the latch and
pull the disk module out until it disengages from the backplane. Leave it in its
slot for two to three minutes to allow the disk drive to spin down before removing
the disk module from the enclosure.
If you are going to replace the disk module immediately, refer to “Replace a Disk
Module” below.
If you are not going to replace the disk module immediately insert a filler panel
into the open slot to assure the required cooling.
Replace a Disk Module
1 Refer to your operating system documentation for requirements and procedures
for replacing disk modules.
2 Align the replacement disk module with the disk module slot.
3 Slide the disk module into the slot until it engages with the backplane.
4 Press on the locking handle until it locks. You will hear an audible click when the
locking mechanism is fully engaged.
HP StorageWorks Disk System 2100 / 2110
21
Remove the Disk System
Reverse the installation instructions enclosed with the rackmount kit for your cabinet:
■
■
■
■
A5679A - Hewlett-Packard Rack Systems/E for Enterprise Systems
A5680A - all other Hewlett-Packard rack systems for Enterprise Systems
purchased before November 1998.
A6532A - Hewlett-Packard Rack Systems/E for Commercial Systems
A6533A - all other Hewlett-Packard rack systems for Commercial Systems
purchased before November 1998.
If your disk system is a factory-integrated unit, see the figure below for removal
instructions.
FIGURE 12 Removing the Disk System
If you are exchanging a desktop disk system, be sure to remove and store the plastic
Desktop Disk System Cover for use on the replacement disk system.
English
Some data paths may be slot-dependent. Be sure to note the slot from which
the disk module is removed so it can be installed in the same slot in the
replacement disk system.
CAUTION
22
HP StorageWorks Disk System 2100 / 2110
Setting Up the Hardware Event Monitor (HP-UX
Only)
Hardware event monitors run on HP-UX hosts, versions 10.20 and later. The Disk
Monitor (disk_em) monitors all disks bound to sdisk drivers. Consequently, if the
Disk Monitor is active on your host, it is already set up to monitor the disks of a new
disk system. If you need to install or activate the Disk Monitor, refer to the EMS
Hardware Monitors User’s Guide in the latest IPR Support Media or on the Web
(http://www.docs.hp.com/hpux/diag/).
Note This Disk Monitor should not be confused with the EMS disk
monitor that is used to monitor LVM resources.
The way you configure the monitor determines, among other things, where event
messages will be sent and what level of severity will be reported.
Configuration Overview
The following steps will help you identify and resolve disk system failures:
1 Gather information from all sources:
– Hardware event notifications (page 25)
– Disk system LED status (page 25)
– Online information tools (page 26)
2 Isolate the cause of the problem (Table 7 on page 30).
3 Correct the problem. (See page 19 for disk module removal and replacement.)
4 Verify operational status with ioscan or other host utilities.
HP StorageWorks Disk System 2100 / 2110
23
Event Notification (HP-UX Only)
Event severity ranges from critical to informational:
Critical
An event that causes data loss, host system downtime, or
other loss of service. Host system operation will be affected if
the disk system continues to be used without correction.
Immediate action is required. For example, read data could
not be recovered.
Serious
An event that may cause data loss, host system downtime, or
other loss of service if left uncorrected. Host system and
hardware operation may be adversely affected. The problem
needs repair as soon as possible. For example, the request
queue is full.
Warning
An event that could escalate to a serious condition if not
corrected. Host system operation should not be affected and
normal use of the disk system can continue. Repair is needed
but at a convenient time. For example, the bus failed to reset.
Information
An event that is expected as part of the normal operation of
the hardware. No action is required. For example, write
protection was switched on or off.
Event messages (see Figure 13) contain the following types of information:
■
■
■
■
Message Data – Date and time the message was sent, the source and destination
of the message, and the severity level.
Event Data – Date and time of the event, the host, event ID, name of the monitor,
event number, event class, severity level, hardware path, associated OS error log
entry ID.
Error Description – Narrative information indicating the component that
experienced the event and the nature of the event.
Probable Cause/Recommended Action – The cause of the event and suggested
steps toward a solution. This information should be the first step in
troubleshooting.
English
The Disk Monitor, an EMS hardware event monitor, reports changes in disk status.
Depending on how the monitor is set up, it sends messages to the console, an e-mail
address, a log file, or a third-party application. These messages give early notice of a
disk problem. Events include media errors, failed read and write attempts, invalid
commands, changed operating parameters, failed diagnostics, and many others.
24
HP StorageWorks Disk System 2100 / 2110
FIGURE 13 Sample Hardware Event Notification
Notification Time:
Wed Feb 3 11:27:15 1999
yourserver sent Event Monitor notification information:
/storage/events/disks/default/10_4_4_0.0 is >=1.
Its current value is CRITICAL(5)
Event data from monitor:
Event Time: Wed Feb 3 11:27:15 1999
Hostname: yourserver.rose.hp.com
Event ID: 0x0036b8a313000000002
Event # : 100037
Severity : CRITICAL
IP Address : 15.43.213.13
Monitor
: disk_em
Event Class: I/O
Disk at hardware path 10/4/4/0.0 : Media failure
Associated OS error log entry id(s) : 000000000000000000
Description of Error:
The device was unsuccessful in reading data for the current I/
O request due to an error on the medium. The data could not be
recovered. The request was likely processed in a way which
could cause damage to or loss of data.
Probable Cause / Recommended Action:
The medium in the device is flawed. If the medium is removable,
replace the medium with a fresh one. Alternatively, if the
medium is not removable, the device has experienced a hardware
failure. Repair or replace the device, as necessary.
HP StorageWorks Disk System 2100 / 2110
25
Status LEDs
FIGURE 14 LED Status Indicators
Amber LED (not used)
Green LED
Disk Module
LEDs
System Power
LED
TABLE 6
LED Status Indicators
LED
State
Indication
System Power
Green
Power is on
Blinking
Malfunction - either a fan is not operating
properly or internal voltage is too low.
OFF
Power is off
Green
Installed and spinning up. If the LED is still on
3 minutes after term power is engaged and
there is no I/O activity occurring, the disk may
be faulty.
Flashing
I/O activity on the disk. The LED flashes at
variable speeds, depending on the I/O activity.
The LED may appear to be on solid during
periods of high I/O activity.
OFF
Not installed, not operating, or no I/O activity
Disk Module
English
LEDs indicate the status of the disk system itself and each of the disk modules. A
green system LED is visible on the front of the disk system. It shows that a fault has
occurred or that power is on. Disk activity LEDs are on the front of the disk modules
(see Figure 14 and Table 6 below).
26
HP StorageWorks Disk System 2100 / 2110
View Disk Status
HP-UX and MPE/iX utilities provide descriptive and diagnostic information about
disks, including disk type, firmware revision, and errors. On HP-UX and MPE/iX 6.5
or later, the disk utility is Support Tools Manager (STM). For all other operating
systems, consult the appropriate system administration manual for disk module status
checking procedures.
STM Disk Information: HP-UX
STM displays the last-generated Information Log for a selected disk. Start STM and
run the Information tool as follows.
1 Log on the system.
2 At the system prompt, type xstm&. STM starts and displays a graphic of the
devices on the system.
3 Select the desired disk.
4 Select Information from the Tools menu.
5 To generate a current log, select Run. The log will be displayed as soon as it is
generated
6 To view a log without updating the contents, select Information Log.
7 Select Done when you have finished viewing the information.
8 To quit STM, type exit.
Figure 15 shows a sample Information Log.
HP StorageWorks Disk System 2100 / 2110
27
FIGURE 15 Sample STM Information Log (HP-UX)
English
28
HP StorageWorks Disk System 2100 / 2110
STM Disk Information: MPE/iX 6.5 or Later
STM displays the last-generated Information Log for a selected disk. Start STM and
run the Information tool as follows.
1 Log on the system.
2 At the system prompt (:), type vsclose <physical volume number>. This removes
the disk from use.
3 At the system prompt (:), type cstm. STM starts.
4 At the cstm prompt, type map. STM displays a list of all the disks installed on the
system.
5 Select the desired disk by typing select device <number>; for example, select
device 15.
6 Type information. STM updates the system map.
7 To display the information log, type infolog. A sample information log is shown
in Figure 16.
HP StorageWorks Disk System 2100 / 2110
29
FIGURE 16 Sample STM Expert Tool Disk Error Log (MPE/iX 6.5 or Later)
Write Error Statistics
N/A
0
0
0
0
6.3253e+10
0
Read Error Statistics
Errors Corrected Without Delay:
Errors Corrected With Delay:
Total Retries:
Total Errors Corrected:
Correction Algorithm Executions:
Total Bytes Processed:
Total Uncorrected Errors:
23781
0
0
23781
23781
9.6191e+10
0
Read Reverse Error Statistics
Errors Corrected Without Delay:
Errors Corrected With Delay:
Total Retries:
Total Errors Corrected:
Correction Algorithm Executions:
Total Bytes Processed:
Total Uncorrected Errors:
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Verify Error Statistics
Errors Corrected Without Delay:
Errors Corrected With Delay:
Total Retries:
Total Errors Corrected:
Correction Algorithm Executions:
Total Bytes Processed:
Total Uncorrected Errors:
Non-Medium Error Counts:
0
0
0
0
0
36864
0
0
English
Errors Corrected Without Delay:
Errors Corrected With Delay:
Total Retries:
Total Errors Corrected:
Correction Algorithm Executions:
Total Bytes Processed:
Total Uncorrected Errors:
30
HP StorageWorks Disk System 2100 / 2110
Isolating Faults
Table 7 lists the probable causes and solutions for problems you may detect on the
disk system. When more than one problem describes your situation, investigate the
first solution that applies. The table lists the most basic problems first and excludes
them from subsequent problem descriptions.
Erratic LED behavior on the disk system could be observed in the following
situations:
■
When a server that is connected to a Disk System 2110 is powered down or loses
power (and the disk system remains powered on)
■
When the disk system is powered up when connected to a downed server
■
When an unconnected disk system is powered up
An example of this LED behavior is the LEDs staying lit solidly. This condition is
caused by the disk system being deprived of term power when the server loses power
or is powered down. The disk system does not provide its own term power. It relies on
the host bus adapter to which it is connected for term power.
TABLE 7
Troubleshooting Table
Problem
Description
LED
State
Disk system System
fails to power power LED
on when
is off
installed
System
power LED
is blinking
Operating
system
reports
errors on a
device
Disk
module
LED is on
solid or off
Probable Cause
Solution
Power cord is not plugged in.
Plug in the power
cord.
The power button is not
pressed.
Press the power
button.
AC breaker is tripped or AC
power source has failed.
Confirm AC power
availability.
The PDU/PDRU is defective.
Replace the PDU/
PDRU.
Enclosure chassis is faulty.
Replace the enclosure
chassis.
Power supply is defective.
Replace the enclosure
chassis.
Cooling fans are not spinning
at the correct speed.
Replace the enclosure
chassis.
Use diagnostic utilities to
determine disk status.
Depending on the
results, monitor or
replace disk module.
HP StorageWorks Disk System 2100 / 2110
LED
State
ioscan (HPUX) lists disk
as NO_HW,
or Mapper or
dstat all
(MPE/iX) lists
no device
type
Disk
module
LED is on
solid or off
Unable to
configure
device for
use by
operating
system
Disk
module
LED is on
solid or off
Probable Cause
Solution
Disk module is faulty.
Replace the disk
module.
Enclosure is faulty.
Replace the enclosure
chassis.
If the all disks on the bus have Replace the cable.
this problem, the cable is
faulty.
Disk module possibly not
correctly seated.
Remove and reinstall
the disk module.
If troubleshooting an existing If the problem cannot
installation, run diagnostics to be resolved, replace
determine drive status.
the disk module.
English
Problem
Description
31
32
HP StorageWorks Disk System 2100 / 2110
Reference Information
Product Numbers and Options
TABLE 8
Product Numbers
Disk System 2100
Product
Number
UPC Code
Description
A5675A
(None)
Field-racked disk system with at least one drive
A5675AD
(None)
Desktop disk system with at least one drive
A5675AZ
(None)
Factory-racked disk system with at least one drive
A5675AE
0 88698-48848 5
Field-racked disk system, empty enclosure only
A5675ED
0 88698-48849 2
Desktop disk system, empty enclosure only
Disk System 2110
Product
Number
UPC Code
Description
A7381A
8 08736-55999 7
Field-racked disk system with at least one drive
A7381AD
8 08736-56000 9
Desktop disk system with at least one drive
A7381AZ
8 08736-56002 3
Factory-racked disk system with at least one drive
A7381AE
8 08736-56001 6
Field-racked disk system, empty enclosure only
A7381ED
8 08736-56003 0
Desktop disk system, empty enclosure only
When ordering disk modules for a product, specify Option OD1 to install the module
in the product before it ships from the factory. For example, to order a desktop Disk
System 2110 with one 18-GB, 15,000 rpm disk module, request the following:
Product
Number
Quantity Description
A7381AD
1
Desktop Disk System 2110
A7328A
1
18-GB 15,000 rpm LVD U320 disk module
A7328A (OD1)
1
Factory integration of the disk module
HP StorageWorks Disk System 2100 / 2110
33
Upgrade Disk Products Available
Available Upgrade Disk Modules
Product
Number
UPC Code
Description1
A6571A
8 08736-45416 2
36-GB 10,000 rpm LVD U320 disk module
A7285A
8 08736-45417 9
73-GB 10,000 rpm LVD U320 disk module
A7286A2
8 08736-45418 62
73-GB 15,000 rpm LVD U320 disk module
A7287A2
8 08736-45419 32
146-GB 10,000 rpm LVD U320 disk module
A7328A
8 08736-33052 7
18-GB 15,000 rpm LVD U320 disk module
A7329A
8 08736-33053 4
36-GB 15,000 rpm LVD U320 disk module
1
The U320 drives are supported at 160 MB/s speeds only. U320 drives do not operate
reliably 320 MB/s speeds and are not supported at those speeds. This is due to
limitations within the controller and not the disk mechanisms.
2
May only be used in Disk System 2110.
TABLE 10 Upgrade Products for Hewlett-Packard Systems
Product
Number
Description
A4999A
Single Port Ultra2 SCSI Host Bus Adapter for Hewlett-Packard
Workstations
A5675A
HP StorageWorks Disk System 2100
A5679A
Rail kit for the Rittal Style Rack Systems and HP Rack Systems/E
A5680A
Rail kit for HP Rack Systems
A5856A
Internal Disk Array Controller for HP-UX Systems
A6828A
Single Port Ultra160 SCSI Host Bus Adapter for HP-UX Systems
A6829A
Dual Port Ultra160 SCSI Host Bus Adapter for HP-UX Systems
A7059A
Windows and Linux Ultra160 SCSI Host Bus Adapter
A7060A
Windows and Linux Dual Port Ultra160 SCSI Host Bus Adapter
A7381A
HP StorageWorks Disk System 2110
C2364A
LVD/SE SCSI Terminator (HDTS68)
P3413A
Single Port Ultra3 SCSI Host Bus Adapter for HP Netservers
English
TABLE 9
34
HP StorageWorks Disk System 2100 / 2110
TABLE 11 Replaceable Parts
Product
Number Description
Customer
Field
Replaceable Replaceable Replaceable
Part Numbers Unit (CRU) Unit (FRU)
A5675A
DS2100 Base Disk System Assembly
A5675-69003
Yes
Yes
A6198A
Disk Filler Panel
A6198-67002
Yes
Yes
A6571A* 36-GB 10,000 rpm LVD U320 disk mod. A6571-69001
Yes
Yes
A7285A* 73-GB 10,000 rpm LVD U320 disk mod. A7285-69001
Yes
Yes
A7286A* 73-GB 15,000 rpm LVD U320 disk mod. A7286-69001
Yes
Yes
A7287A* 146-GB 10,000 rpm LVD U320 disk mod. A7287-69001
Yes
Yes
A7328A* 18-GB 15,000 rpm LVD U320 disk mod. A7328-69001
Yes
Yes
A7329A* 36-GB 15,000 rpm LVD U320 disk mod. A7329-69001
Yes
Yes
A7381A
DS2110 Base Disk System Assembly
A7381-69001
Yes
Yes
Desktop Disk System Cover
5065-5217
No
Yes
Desktop Disk System Feet
0403-0285
No
Yes
* The U320 drives are supported at 160 MB/s speeds only. U320 drives do not operate reliably 320 MB/s
speeds and are not supported at those speeds. This is due to limitations within the controller and not the
disk mechanisms.
TABLE 12 Supported HP Cables and Terminators
Order
Number
Description
Part
Number
C2978B
0.5-meter HDT S68 SCSI multimode cable
5183-2670
C2911C
1.0-meter HDT S68 SCSI multimode cable
5183-2671
C2979B
1.5-meter HDT S68 SCSI multimode cable
5183-2672
C2924C
2.5-meter HDT S68 SCSI multimode cable
5183-2673
C7521A
5.0-meter HDT S68 SCSI multimode cable
5183-2678
C2361B
1.0-meter VHDT S68/HDT S68 SCSI multimode cable
5183-2674
C2362B
2.5-meter VHDT S68/HDT S68 SCSI multimode cable
5183-2675
C2365B
5.0-meter VHDT S68/HDT S68 SCSI multimode cable
5183-2676
C2364A
SCSI Terminator LVD/SE HDTS68
5183-2657
HP StorageWorks Disk System 2100 / 2110
35
Specifications
Measure
Metric
English
Width
45.08 cm
17.75 in
Depth
38.10 cm
15.0 in
Height
4.32 cm
1.7 in
Weight without disk modules
4.94 kg
10.90 lbs
Weight fully loaded
8.11 kg
17.89 lbs
Electrical Specifications
TABLE 14 AC Power Requirements
Electrical Element
Requirement
Product Voltage Range
100 - 240 VAC RMS
Product Frequency Range
50 - 60 Hz
TABLE 15 Environmental Specifications
Climate Control
Disk System 2100
Temperature (dry bulb)
Disk System 2110
Temperature (dry bulb)
Relative Humidity
(non-condensing)
Altitude (based on disks)
Operating
0°C - +40°C
Storage
-40°C - +70°C
Operating
0°C - +35°C
Storage
-40°C - +70°C
Operating
5% - 95% Relative Humidity at 40°C
Storage
90% Relative Humidity at 65°C
Operating
-1000 ft to +10,000 ft (3048 M)
Storage
40,000 ft (12,092 M)
Heat Dissipation (maximum) Operating
< 100 watts
English
TABLE 13 Physical Dimensions
36
HP StorageWorks Disk System 2100 / 2110
Operating Temperatures
If the storage system is installed in a multi-unit rack assembly, the operating ambient
temperature of the rack environment may exceed room ambient temperature. For the
Disk System 2100 the rack environment ambient temperature cannot exceed 40°
Celsius (104° Fahrenheit). For the Disk System 2110 the rack environment ambient
temperature cannot exceed 35° Celsius (95° Fahrenheit).
If your storage system contains less than 4 disk modules, the remaining empty slots
require filler panels. These filler panels (part number A6198-60002) ensure that the
proper cooling is maintained within the storage system.
Regulatory Statements
Safety Certifications
UL listed, UL 1950:1995 – 3rd Edition
CSA certified, C22.2 No. 950:1995
TUV certified with GS mark, EN 60950:1992 + A1:1993, A2:1993, A3:1995,
A4:1997, A11:1997
CE mark (see I. Declaration of Conformity on page 39)
EMC Compliance
Australia: AS/NZS 3548, Class A
Canada: ICES-003, Class A
China: GB9254-88
European Union: EN55022 Class A, EN55024
Japan: VCCI Class A
Taiwan: CNS 13438, Class A
US: 47 CFR Parts 2 & 15, Class A
A. FCC Notice for United States
The Federal Communications Commission (in 47 CFR 15.105) has specified that the
following notice be brought to the attention of the users of this product.
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
HP StorageWorks Disk System 2100 / 2110
37
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
B. Canadian Notice (Avis Canadien)
This Class A digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.
Cet appareil numérique de la classe A respecte toutes les exigences du Règlement sur
le matériel brouilleur du Canada.
C. Notice for European Union
This is a Class A product. In a domestic environment this product may cause radio
interference, in which case the user may be required to take adequate measures.
D. Notice for France
DECLARATION D'INSTALLATION ET DE MISE EN EXPLOITATION d'un
matériel de traitement de l'information (ATI), classé A en fonction des niveaux de
perturbations radioélectriques émis, définis dans la norme européenne EN 55022
concernant la Compatibilité Electromagnétique.
E. Notice for Japan
F. Harmonics Conformance (Japan)
English
Hewlett-Packard’s certification tests were conducted with a Hewlett-Packard
supported computer system and Hewlett-Packard shielded cables, such as those you
received with your storage product. Changes or modifications not expressly approved
by Hewlett-Packard could void the user’s authority to operate the equipment. Cables
used with this device must be properly shielded to comply with the requirements of
the FCC.
38
HP StorageWorks Disk System 2100 / 2110
G. BSMI
H. Notice for Germany
Schalldruckpegel Lp = 55.0 dB(A)
Am Arbeitsplatz (operator position)
Normaler Betrieb (normal operation)
Nach ISO 7779:1999 (Typprüfung)
HP StorageWorks Disk System 2100 / 2110
39
I. Declaration of Conformity
According to ISO/IEC Guide 22 and EN 45014
Manufacturer's Name:
Hewlett-Packard Company
Manufacturer's Address:
11311 Chinden Blvd.
Boise, ID 83714
USA
Declares, that the product
Product Name:
Product Number:
Regulatory Model Number:
Product Options:
hp StorageWorks disk system 2100 and 2110
A5675A/AD/AZ/ED, A5676A/AD, and
A7381A/AD/AE/AZ/ED
BOISA-0301
All
Conforms to the following Product Specifications:
Safety:
EMC:
IEC 60950:1991+A1+A2+A3+A4 / EN 60950:1992+A1+A2+A3+A4+A11
GB 4943:1995
IEC 60825-1:1993 / EN 60825-1:1994 +A11, Class 1 (Laser/LED)
CISPR 22:1997+A1 / EN 55022:1998 +A1 Class A 1
GB 9254:1988
CISPR 24:1997 / EN 55024:1998
IEC 61000-3-2:1995 / EN 61000-3-2:1995 + A14
IEC 61000-3-3:1994 / EN 61000-3-3:1995
Supplementary Information:
The product herewith complies with the requirements of the Low Voltage Directive
73/23/EEC and the EMC Directive 89/336/EEC and carries the CE-marking accordingly.
1) The Product was tested in a worst-case configuration which maximizes RFI
emissions.
Boise, ID USA
March 7, 2003
European contact for regulatory topics only: Hewlett-Packard GmbH, HQ-TRE, Herrenberger Strasse 140, and D-71034
Böblingen (FAX: + 49-7031-14-3143)
English
DECLARATION OF CONFORMITY
40
HP StorageWorks Disk System 2100 / 2110
Product Web Site
For the most current information about the HP StorageWorks Disk System 2100, visit
the support Web site located at http://www.hp.com/support/ds2100
For the most current information about the HP StorageWorks Disk System 2110, visit
the support Web site located at http://www.hp.com/support/ds2110.
Related Documents
The following resources contain information on using the system software interfaces
to the HP StorageWorks Disk System 2100 / 2110:
■
■
Online Diagnostics (for HP 9000): Support Tools Manager Overview, available at
http://docs.hp.com/hpux/diag/
HP-UX documentation, available at http://docs.hp.com
HP StorageWorks Disk System 2100 / 2110
41
English
42
HP StorageWorks Disk System 2100 / 2110
Download PDF

advertising