- Computers & electronics
- Software
- HP
- StorageWorks Enterprise File Services WAN Accelerator
- User's manual
advertisement
HP StorageWorks
Enterprise File Services WAN Accelerator 3.0.4
Management Console user guide
Part number: AG421–96002
Fifth edition: March 2007
Legal and notice information
© Copyright 2006–2007 Hewlett-Packard Development Company, L.P.
© Copyright 2003–2007 Riverbed Technology, Inc.
Hewlett-Packard Company makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose. Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
This document contains proprietary information, which is protected by copyright. No part of this document may be photocopied, reproduced, or translated into another language without the prior written consent of Hewlett-Packard. The information is provided “as is” without warranty of any kind and is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Linux is a trademark of Linus Torvalds in the United States and in other countries.
Microsoft, Windows, Windows NT, Windows 2000, Outlook, and Windows Internet Explorer are trademarks or registered trademarks of Microsoft
Corporation in the United States and in other countries.
UNIX is a registered trademark in the United States and in other countries, exclusively licensed through X/Open Company, Ltd.
Parts of this product are derived from the following software:
Apache © 2000-2003 The Apache Software Foundation. All rights reserved. bsdstr.c, © 1998 Todd C. Miller ([email protected]). All rights reserved.
Busybox, © Eric Andersen
Less © 1984-2002 Mark Nudelman
Libevent, © 2000-2002 Niels Provos. All rights reserved.
LibGD, Version 2.0 licensed by Boutell.Com, Inc.
Libtecla, © 2000, 2001 by Martin C. Shepherd. All rights reserved.
Linux Kernel, © Linus Torvalds md5, md5.cc, © 1995 University of Southern California. All rights reserved. © 1991-2, RSA Data Security, Inc. All rights reserved.
my_getopt.{c,h}, © 1997, 2000, 2001, 2002, Benjamin Sittler. All rights reserved.
NET-SNMP: © 1989, 1991, 1992 by Carnegie Mellon University. All rights reserved.
OpenSSH, © 2002 Nils Nordman. All rights reserved.
ptmalloc © 2001 Wolfram Gloger sSMTP, © Mark Ryan, Hugo Haas, Christoph Lameter, and Dave Collier-Brown
Vixie-Cron, © 1988,1990,1993,1994 by Paul Vixie. All rights reserved.
Zile, © 1997-2001 Sandro Sigalam © 2003 Reuben Thomas. All rights reserved.
For detailed copyright and license agreements, see the HP StorageWorks Enterprise File Services WAN Accelerator Installation and Configuration
Guide. For modified source code (where required), see the HP technical support site at http://www.hp.com.
Certain libraries were used in the development of this software, licensed under GNU Lesser General Public License, Version 2.1, February 1999. For the copyright and license agreement, see the HP StorageWorks Enterprise File Services WAN Accelerator Installation and Configuration Guide. For a list of libraries and source material (where required), see the HP technical support site at http://www.hp.com.
Enterprise File Services WAN Accelerator 3.0.4 Management Console user guide
Contents
About This Guide.................................................................................. 7
Types of Users ................................................................................ 7
Organization of This Guide ............................................................ 7
Document Conventions .................................................................. 8
Hardware and Software Dependencies ................................................. 8
Ethernet Network Compatibility........................................................... 9
Antivirus Compatibility ........................................................................ 9
Additional Resources .......................................................................... 10
Related HP Documentation .......................................................... 10
Online Documentation.................................................................. 10
Related Reading............................................................................ 11
Technical Support......................................................................... 11
HP Storage Web Site........................................................................... 11
Chapter 1 Overview of the HP EFS WAN Accelerator Management
Console ...................................................................................... 13
Connecting to the Management Console ............................................ 13
Connecting to the Management Console...................................... 13
The Home: Welcome Page ........................................................... 15
Navigating in the Management Console............................................. 16
Navigating in the Management Console ...................................... 16
Chapter 2 Configuring the HP EFS WAN Accelerator .............................. 21
Setting Optimization Services............................................................. 22
Enabling In-Path and Out-of-Path Support .................................. 22
Setting In-Path Rules.................................................................... 25
Modifying In-Path Descriptions ................................................... 30
Configuring CIFS Protocol Support............................................. 31
Configuring MAPI Protocol Options ........................................... 34
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 3
4
Configuring MS-SQL Protocol Options....................................... 36
Enabling the NFS-Application Streamlining................................ 38
Modifying NFS Server Settings ................................................... 39
Enabling HSTCP Protocol Options .............................................. 42
Enabling Connection Pooling....................................................... 44
Enabling Transparent Prepopulation ............................................ 46
Setting Host Parameters...................................................................... 52
Setting the Primary Interface........................................................ 52
Setting In-Path Interfaces ............................................................. 54
Setting Auxiliary Interfaces.......................................................... 58
Setting Main Static Routes ........................................................... 59
Setting Static In-Path Routes........................................................ 60
Setting the DNS............................................................................ 61
Modifying the Host Name ............................................................ 63
Mapping Hosts to IP Addresses ................................................... 63
Setting Proxies.............................................................................. 64
Setting Advanced Network Parameters .............................................. 65
Enabling Asymmetric Routing Auto-Detection ........................... 66
Enabling Connection Forwarding................................................. 68
Enabling Encryption..................................................................... 70
Enabling Failover and Data Store Synchronization ..................... 73
Enabling NetFlow......................................................................... 77
Setting Peering Rules ................................................................... 79
Enabling Quality of Service ......................................................... 81
Modifying a QoS Class ................................................................ 85
Setting QoS Marking.................................................................... 87
Modifying QoS Marking Descriptions......................................... 89
Modifying Service Ports............................................................... 90
Enabling Simplified Routing........................................................ 92
Enabling WCCP Groups .............................................................. 94
Modifying WCCP Group Settings ............................................... 96
Enabling Proxy File Service ............................................................... 99
Enabling PFS ................................................................................ 99
Adding PFS Shares..................................................................... 102
Creating Port Labels ......................................................................... 113
Creating Port Labels ................................................................... 113
Modifying Ports in a Port Label ................................................. 115
Setting Report Parameters................................................................. 115
Setting Alarm Parameters........................................................... 116
Setting Email Notification.......................................................... 117
Setting SNMP Parameters .......................................................... 119
Setting SNMP Trap Receivers.................................................... 120
Setting Monitored Ports.............................................................. 121
Setting Logging Options ................................................................... 123
Setting Local Logging ................................................................ 123
Setting Remote Logging............................................................. 124
Setting the Date and Time................................................................. 125
C ONTENTS
Setting the Date and Time .......................................................... 125
Setting NTP Servers ................................................................... 126
Setting Authentication Methods ....................................................... 127
Setting General Authentication .................................................. 127
Setting the Administrative Password ......................................... 129
Setting the Monitor Password .................................................... 130
Setting RADIUS Servers............................................................ 131
Setting TACACS+ Servers ......................................................... 133
Modifying Web Settings............................................................. 135
Setting the Message of the Day (MOTD)................................... 136
Managing Licenses ........................................................................... 137
Updating Your Licenses ............................................................. 137
Viewing Scheduled Jobs ................................................................... 138
Viewing Scheduled Jobs............................................................. 139
Managing Configurations ................................................................. 139
Upgrading Your Software ................................................................. 142
Starting and Stopping Services ......................................................... 144
Rebooting the HP EFS WAN Accelerator ........................................ 145
Shutting Down the HP EFS WAN Accelerator................................. 145
Chapter 3 Creating HP EFS WAN Accelerator Reports and Logs ......... 147
Creating Performance Reports.......................................................... 147
Creating Bandwidth Optimization Reports ................................ 148
Creating Data Store Hits Reports ............................................... 150
Creating Data Reduction Reports............................................... 152
Creating NFS Statistics Report................................................... 155
Creating Throughput Reports ..................................................... 157
Creating Traffic Summary Reports ............................................ 159
Viewing Appliance Reports .............................................................. 162
Viewing Data Store Reports ....................................................... 162
Viewing TCP Statistics Report................................................... 163
Viewing Networking Reports ........................................................... 165
Viewing Connected Appliances Reports .................................... 166
Viewing Connection History ...................................................... 167
Viewing Current Connections .................................................... 170
Viewing the Current Connection Details Report........................ 172
Viewing Connection Pooling...................................................... 174
Viewing Interface Statistics........................................................ 177
Creating Link State Reports ....................................................... 178
Creating Neighbor Statistic Reports........................................... 181
Creating QoS Statistics Reports ................................................. 182
Viewing System Health Reports ....................................................... 185
Viewing Alarm Status Reports ................................................... 185
Creating CPU Utilization Reports .............................................. 188
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 5
6
Creating Memory Paging Reports .............................................. 190
Viewing Proxy File Service Reports................................................. 192
Viewing PFS Share Status Reports............................................. 192
Viewing PFS Statistics ............................................................... 193
Exporting Performance Statistics Reports ........................................ 196
Exporting Performance Statistics ............................................... 196
Viewing System Diagnostic Files ..................................................... 197
Viewing System Dump Files ...................................................... 197
Viewing System Snapshots......................................................... 198
Viewing TCP Dump Files .......................................................... 199
Viewing HP EFS WAN Accelerator Logs ........................................ 200
Viewing HP EFS WAN Accelerator Logs.................................. 201
Contacting Technical Support .................................................... 202
Viewing Online Help Contents................................................... 202
Appendix A HP EFS WAN Accelerator Ports .............................................. 203
Commonly Optimized Ports ............................................................. 204
Commonly Excluded Ports ............................................................... 204
Interactive Ports Forwarded by the HP EFS WAN Accelerator ....... 205
Secure Ports Forwarded by the HP EFS WAN Accelerator ............. 206
Appendix B HP EFS WAN Accelerator MIB ................................................ 209
Accessing the HP EFS WAN Accelerator Enterprise MIB .............. 209
SNMP Traps...................................................................................... 210
HP EFS WAN Accelerator Enterprise MIB...................................... 211
C ONTENTS
Introduction
In This
Introduction
Welcome to the HP EFS WAN Accelerator Management Console User Guide. Read this introduction for an overview of the information provided in this guide and for an understanding of the documentation conventions used throughout. This introduction contains the following sections:
next
“Hardware and Software Dependencies” on page 8
“Ethernet Network Compatibility” on page 9
“Antivirus Compatibility” on page 9
“Additional Resources” on page 10
About This Guide
The HP EFS WAN Accelerator Management Console User Guide describes how to manage and monitor the HP StorageWorks Enterprise File Services WAN Accelerator using the Management Console.
Types of Users
This guide is written for storage and network administrators with familiarity administering and managing networks using Common Internet File System (CIFS),
Hypertext Transport Protocol (HTTP), File Transfer Protocol (FTP), and Microsoft
Exchange.
Organization of
This Guide
The HP EFS WAN Accelerator Management Console User Guide includes the following chapters:
Chapter 1, “Overview of the HP EFS WAN Accelerator Management Console,”
describes how to connect to and navigate in the Management Console.
Chapter 2, “Configuring the HP EFS WAN Accelerator,” describes how to
configure and manage the HP EFS WAN Accelerator using the Management
Console.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 7
8
Document
Conventions
Chapter 3, “Creating HP EFS WAN Accelerator Reports and Logs,”
describes how to create and view HP EFS WAN Accelerator reports and logs.
Appendix A, “HP EFS WAN Accelerator Ports,”
provides a list of commonly optimized ports, excluded ports, default ports, and interactive and secure ports that are automatically forwarded by the HP EFS WAN Accelerator.
Appendix B, “HP EFS WAN Accelerator MIB,”
provides a reference for the HP
EFS WAN Accelerator Enterprise Simple Network Management Protocol
(SNMP) Message Information Block (MIB).
A glossary of terms follows the chapters, and a comprehensive index directs you to areas of particular interest.
This manual uses the following standard set of typographical conventions to introduce new terms, illustrate screen displays, describe command syntax, and so forth.
Convention italics boldface
Courier
KEYSTROKE
Meaning
Within text, new terms and emphasized words appear in italic typeface.
Within text, commands, keywords, identifiers (names of classes, objects, constants, events, functions, program variables), environment variables, filenames, Graphical User Interface (GUI) controls, and other similar terms appear in bold typeface.
Information displayed on your terminal screen and information that you are instructed to enter appear in Courier font.
Keys that you are to press appear in uppercase letters in Helvetica font.
HP EFS WAN Accelerator
Component
Management Console
Hardware and Software Dependencies
The following table summarizes the hardware, software, and operating system requirements for the Management Console.
Hardware Requirements
• Any computer that supports a
Web browser with a color image display.
Software Requirements
Operating System Requirements
• The Management Console has been tested with
Mozilla Firefox, version 1.0.x and 1.5.x and
Microsoft Internet Explorer version 6.0x.
NOTE: Javascript and cookies must be enabled in your browser.
NOTE: If you want to encrypt your communication, you must have a Secure Sockets
Layer (SSL) capable browser.
I NTRODUCTION
Ethernet Network Compatibility
The HP EFS WAN Accelerator supports the following types of Ethernet networks:
Ethernet Logical Link Control (LLC) (IEEE 802.2 - 2002)
Fast Ethernet 100 Base-TX (IEEE 802.3 - 2002)
Gigabit Ethernet over Copper 1000 Base-T and Fiber 1000 Base-SX (LC connector) (IEEE 802.3 - 2002)
The Primary port in the HP EFS WAN Accelerator is 10 Base-T/100, Base-TX/1000, and Base-T/SX Mbps (IEEE 802.3 -2002).
In-path HP EFS WAN Accelerator ports are 10/100/1000 Base-TX or Gigabit Ethernet
1000Base-T/SX (IEEE 802.3 – 2002) (depending on your order).
The HP EFS WAN Accelerator supports Virtual Local Area Network (VLAN) Tagging
(IEEE 802.1Q - 2003). It does not support the Cisco InterSwitch Link (ISL) protocol.
All copper interfaces are auto-sensing for speed and duplex (IEEE 802.3 - 2002).
The HP EFS WAN Accelerator auto-negotiates speed and duplex mode for all data rates and supports full duplex mode and flow control (IEEE 802.3 – 2002).
The HP EFS WAN Accelerator with a Gigabit Ethernet card supports Jumbo Frames on in-path and primary ports.
Antivirus Compatibility
The HP EFS WAN Accelerator has been tested with the following antivirus software with no impact on performance:
Network Associates (McAfee) VirusScan v7.0.0 Enterprise on the server
Network Associates (McAfee) VirusScan v7.1.0 Enterprise on the server
Network Associates (McAfee) VirusScan v7.1.0 Enterprise on the client
Symantec (Norton) AntiVirus Corporate Edition v8.1 on the server
The HP EFS WAN Accelerator has been tested with the following antivirus software with a noticeable to moderate impact on performance:
F-Secure Anti-Virus v5.43 on the client
F-Secure Anti-Virus v5.5 on the server
Network Associates (McAfee) NetShield v4.5 on the server
Network Associates VirusScan v4.5 for multiplatforms on the client
Symantec (Norton) AntiVirus Corporate Edition v8.1 on the client
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 9
Additional Resources
This section describes the following resources that supplement the information in this guide:
“Related HP Documentation” on page 10
“Online Documentation” on page 10
Related HP
Documentation
You can access the complete document set for the HP EFS WAN Accelerator from the
HP StorageWorks EFS WAN Accelerator Documentation Set CD-ROM:
HP StorageWorks Enterprise File Services WAN Accelerator Installation and
Configuration Guide describes how to install and configure the HP EFS WAN
Accelerator.
HP StorageWorks Enterprise File Services WAN Accelerator Command Line
Interface Reference Manual is a reference manual for the HP EFS WAN
Accelerator command-line interface for the HP EFS WAN Accelerator. It lists commands, syntax, parameters, and example usage.
HP StorageWorks Enterprise File Services WAN Accelerator Deployment Guide describes how to deploy the HP EFS WAN Accelerator in complex network environments (for example, environments using Web Cache Communication
Protocol (WCCP), Policy-Based Routing (PBR), and Layer-4 switches).
HP StorageWorks Enterprise File Services Remote Copy Utility Reference
Manual describes how to install and deploy the HP EFS Remote Copy Utility
(RCU). The RCU is an optional utility of the HP EFS WAN Accelerator that copies, mirrors, and transparently prepopulates data. You can download the RCU from the HP Technical Support site located at http://www.hp.com.
HP StorageWorks Enterprise File Services WAN Accelerator Manager User’s
Guide describes how to install, configure, and administer a network made up of multiple HP EFS WAN Accelerators using the HP StorageWorks Enterprise File
ServicesWAN Accelerator Manager.
HP StorageWorks Enterprise File Services N4c WAN Accelerator 4-port NIC
Installation Guide describes how to install bypass cards in the HP EFS WAN
Accelerator.
Online
Documentation
The HP EFS WAN Accelerator documentation set is periodically updated with new information. To access the most current version of the HP EFS WAN Accelerator documentation and other technical information, consult the HP Technical Support site located at http://www.hp.com.
10 I NTRODUCTION
Related
Reading
Technical
Support
To learn more about network storage systems and network administration, consult the following books:
Microsoft Windows 2000 Server Administrator’s Companion by Charlie Russell and Sharon Crawford (Microsoft Press, 2000)
Common Internet File System (CIFS) Technical Reference by the Storage
Networking Industry Association (Storage Networking Industry Association,
2002)
TCP/IP Illustrated, Volume I, The Protocols by W. R. Stevens (Addison-Wesley,
1994)
Internet Routing Architectures (2nd Edition) by Bassam Halabi (Cisco Press,
2000)
Contacting HP
This section describes how to contact departments within HP.
Telephone numbers for worldwide technical support are listed on the following HP web site: http://www.hp.com/support . From this web site, select the country of origin.
For example, the North American technical support number is 800-633-3600.
NOTE: For continuous quality improvement, calls may be recorded or monitored.
Be sure to have the following information available before calling:
Technical support registration number (if applicable)
Product serial numbers
Product model names and numbers
Applicable error messages
Operating system type and revision level
Detailed, specific questions
HP Storage Web Site
The HP web site has the latest information on this product, as well as the latest drivers.
Access the storage site at: http://www.hp.com/country/us/en/prodserv/storage.html
.
From this web site, select the appropriate product or solution.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 11
12 I NTRODUCTION
CHAPTER 1
Overview of the HP EFS WAN
Accelerator Management Console
In This Chapter This chapter introduces the Management Console. This chapter includes the following sections:
“Connecting to the Management Console,” next
“Navigating in the Management Console” on page 16
NOTE: If you prefer, you can use the HP EFS WAN Accelerator Command Line Interface
(CLI) to perform configuring and monitoring tasks. For detailed information, see the HP
StorageWorks Enterprise File Services WAN Accelerator Command Line Interface Reference
Manual.
This chapter assumes you have installed and configured the HP EFS WAN
Accelerator. For detailed information, see the HP StorageWorks Enterprise File
Services WAN Accelerator Installation and Configuration Guide.
This chapter also assumes you are familiar with the various deployment options available to you. For detailed information, see the HP StorageWorks Enterprise File
Services WAN Accelerator Deployment Guide.
Connecting to the
Management
Console
Connecting to the Management Console
You can connect to the Management Console through any supported Web browser.
To connect to the Management Console you must know the Uniform Resource Locator
(URL) and administrator password that you assigned in the configuration wizard of the
HP EFS WAN Accelerator. For detailed information, see the HP StorageWorks
Enterprise File Services WAN Accelerator Installation and Configuration Guide.
NOTE: Cookies and Javascript must be enabled in your Web browser.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 13
To connect to the
Management Console
1. Enter the URL for the Management Console in the location box of your Web browser:
protocol://host.domain
protocol is http or https. Hypertext Transport Protocol Secure (HTTPS) uses the
Secure Sockets Layer (SSL) protocol to ensure a secure environment. If you use
HTTPS to connect, you are prompted to inspect and verify the SSL key.
host is the host name you assigned to the HP EFS WAN Accelerator during initial configuration. If your Domain Name Service (DNS) server maps that IP address to a name, you can specify the DNS name.
domain is the full domain name for the appliance.
TIP: Alternatively, you can specify the IP address instead of the host and domain name.
The Management Console appears, displaying the Welcome page.
Figure 1-1. Welcome Page
14
2. In the Account text box, type the user login: admin, monitor, or a login from a
Remote Authentication Dial-In User Service (RADIUS), or a Terminal Access
Controller Access Control System (TACACS+) database. The default login is
admin.
Users with administrator (admin) privileges can configure and administer the HP
EFS WAN Accelerator. Users with monitor (monitor) privileges can view HP
EFS WAN Accelerator reports and system logs.
3. In the Password text box, type the password you assigned in the configuration wizard of the HP EFS WAN Accelerator. (The HP EFS WAN Accelerator is shipped with the default password: password.)
4. Click Login to display the Home: Welcome page. The Home: Welcome page summarizes the current status of your system and provides links to connected appliances, a traffic summary, alarms, system logs, and technical support information.
O VERVIEW OF THE HP EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE
The Home:
Welcome Page
The Management Console Home: Welcome page includes the current status of the HP
EFS WAN Accelerator and the Traffic Overview report.
Figure 1-2. The Home: Welcome Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 15
The following table describes the information included in the Home: Welcome page.
Field Description
Status Bar The status bar appears on every page of the Management Console and displays the current status of the system. To check the status of the system, click the link in the status bar. For detailed information about system alarms, see
“Viewing Alarm Status Reports” on page 185
. The HP EFS WAN Accelerator can be in one of the following states:
• Healthy. All systems are functioning properly.
• Degraded. A system alarm has been triggered. Alarms are triggered for software version mismatches, abnormal memory page swapping activity, when the CPU utilization threshold has been reached, or on the Series 5000 and 3000, if there is a
Redundant Array of Independent Disks (RAID) issue. For detailed information about
system alarms, see “Viewing Alarm Status Reports” on page 185
.
• Critical. Critical indicates one of the following states:
– Bypass Mode. The HP EFS WAN Accelerator service is not functioning or the HP
EFS WAN Accelerator is in bypass mode. For detailed information, see
“Starting and Stopping Services” on page 144
.
– Unlicensed. The HP EFS WAN Accelerator does not have a a base license key or
the key has expired. For detailed information, see “Updating Your Licenses” on page 137 .
– Corrupted Store. The HP EFS WAN Accelerator data store is corrupt. For detailed information, see
“Starting and Stopping Services” on page 144
.
– Service Halted. The HP EFS WAN Accelerator has detected a software error that prevents the HP EFS WAN Accelerator service from continuing. For detailed information, see
“Starting and Stopping Services” on page 144
.
• Connection Limit. The system has reached the maximum number of connections for this model of the HP EFS WAN Accelerator. For detailed information about system
alarms, see “Viewing Alarm Status Reports” on page 185
.
TIP: The status bar alerts you if you need to save your configuration changes to memory.
To save your changes, click the link in the status bar.
System Up
Time
Service Up
Time
Total time the system has been active.
The state of the HP EFS WAN Accelerator service. The total time the HP EFS WAN
Accelerator has been running or Not Running is displayed. To restart the HP EFS WAN
Accelerator service, see
“Starting and Stopping Services” on page 144
.
Temperature The current Central Processing Unit (CPU) temperature. An alarm is raised if the temperature rises above 70º C.
Navigating in the Management Console
The following section describes how to navigate in the Management Console.
You navigate to the tools and reports available to you in the Management Console using hyperlinked tabs and menus.
Navigating in the
Management
Console
16 O VERVIEW OF THE HP EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE
The following figure illustrates the tabs and menus that appear on each page of the
Management Console.
Figure 1-3. Management Console, The Home: Welcome Page
Click tabbed pages to display configuration and administration tools, reports, logs, and online help.
Click Logout to log out of the system.
Click the Printer icon to print a page or report. Click the
Book icon to display online help.
Menus for tasks you can perform from tabbed pages appear on the left of the Console.
TIP: To revisit the Home: Welcome page, click Home in the navigation bar.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 17
Tabbed Pages and
Menus
You click the hyperlinked tabs to display tools and reports to help you configure and manage your HP EFS WAN Accelerator. The following table summarizes the purpose of each tabbed page.
Tab
Home
Setup
Reports
Purpose
Displays the current status of your system and provides links to connected appliances, a traffic summary, alarms, system logs, and technical support information.
Configure and administer the HP EFS WAN Accelerator.
Create and view performance, network, and appliance reports.
Saving Your
Configuration
Help Display contact information for technical support, and the online-help table of contents.
When you click a hyperlinked tab, a menu for the tasks you can perform appears in the left menu of the Management Console. For example, when you click the Setup tab, the
Setup menu appears.
Menu items are hyperlinks to pages that display tools and reports to help you configure and manage your HP EFS WAN Accelerator. When you click a menu item, you display the primary tool or report for the menu choice.
As you Apply page settings, the values are applied to the running configuration and an orange exclamation point (!) appears in the left menu to remind you to permanently save your configuration settings to disk.
NOTE: The status bar at the top of each page also alerts you if the changes you have made require you to save them to disk. To save your changes, click the link in the status bar to go to the Configuration Manager page.
Restarting the HP
EFS WAN
Accelerator
Service
Printing Pages and
Reports
To print pages and reports
For detailed information about saving your configuration to disk, see
Some configuration settings apply to the HP EFS WAN Accelerator service. The HP
EFS WAN Accelerator service is a daemon that executes in the background performing operations when required.
If the new settings require you to restart the HP EFS WAN Accelerator service an orange exclamation point (!) appears in the left menu to remind you to restart the service. For detailed information, see
“Starting and Stopping Services” on page 144
.
You can print Management Console pages and reports.
• Click the Printer icon in the upper right-side of the page to display a printerfriendly version of the page.
18 O VERVIEW OF THE HP EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE
Displaying Online
Help
To display online help
Logging Out
To log out of the
Management Console
You can view online help that describes each page of the Management Console and the tasks that you can perform.
• Click the Book icon in the upper right-side of the page. The help for the page appears in a new browser window.
The Help tab provides you with the following links to help you administer and manage the HP EFS WAN Accelerator:
Technical Support. Displays HP Technical Support contact information.
Online Help. Displays the online help table of contents.
Click the Logout link to end your session and require subsequent users to authenticate their session. When you click Logout, the Management Console displays the Good-
Bye page.
• Click Logout to display the Good-Bye page and log out of the Management
Console.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 19
20 O VERVIEW OF THE HP EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE
CHAPTER 2
Configuring the HP EFS WAN
Accelerator
In This Chapter This chapter describes how to configure and manage the HP EFS WAN Accelerator using the Management Console. This chapter includes the following sections:
“Setting Optimization Services,”
next
“Setting Host Parameters” on page 52
“Setting Advanced Network Parameters” on page 65
“Enabling Proxy File Service” on page 99
“Creating Port Labels” on page 113
“Setting Report Parameters” on page 115
“Setting Logging Options” on page 123
“Setting the Date and Time” on page 125
“Setting Authentication Methods” on page 127
“Managing Licenses” on page 137
“Viewing Scheduled Jobs” on page 138
“Managing Configurations” on page 139
“Upgrading Your Software” on page 142
“Starting and Stopping Services” on page 144
“Rebooting the HP EFS WAN Accelerator” on page 145
“Shutting Down the HP EFS WAN Accelerator” on page 145
This chapter assumes that you have installed and configured the HP EFS WAN
Accelerator. For detailed information, see the HP StorageWorks Enterprise File
Services WAN Accelerator Installation and Configuration Guide.
If you prefer, you can use the HP EFS WAN Accelerator Command Line Interface
(CLI) to configure your system. For detailed information, see the HP StorageWorks
Enterprise File Services WAN Accelerator Command Line-Interface Reference
Manual.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 21
Setting Optimization Services
This section describes how to set optimization service parameters for the HP EFS
WAN Accelerator. It includes the following sections:
“Enabling In-Path and Out-of-Path Support,”
next
“Setting In-Path Rules” on page 25
“Modifying In-Path Descriptions” on page 30
“Configuring CIFS Protocol Support” on page 31
“Configuring MAPI Protocol Options” on page 34
“Configuring MS-SQL Protocol Options” on page 36
“Enabling the NFS-Application Streamlining” on page 38
“Modifying NFS Server Settings” on page 39
“Enabling HSTCP Protocol Options” on page 42
“Enabling Connection Pooling” on page 44
“Enabling Transparent Prepopulation” on page 46
“Enabling and Synchronizing Prepopulation Shares” on page 47
Enabling In-
Path and Out-of-
Path Support
You can modify general in-path and out-of-path interface settings in the Optimization
Service - General Settings Page.
NOTE: You were prompted to enable in-path or out-of-path support when you completed the installation wizard. This section describes how you can modify these settings.
22
The following types of deployments are available to you:
Physical In-Path. The HP EFS WAN Accelerator is physically in the direct path between the client and server. The clients and servers continue to see client and server IP addresses. Physical in-path configurations are suitable for any location where the total bandwidth is within the limits of the installed HP EFS WAN
Accelerator.
Virtual In-Path. The HP EFS WAN Accelerator is virtually in the path between the client and server. This differs from a physical in-path in that a packet redirection mechanism is used to direct packets to HP EFS WAN Accelerators that are not in the physical path. Redirection mechanisms include Web Cache
Communication Protocol (WCCP), Layer 4 (L4) switches, and Policy-Based
Routing (PBR). In this configuration, clients and servers continue to see client and server IP addresses.
Out-of-Path. The HP EFS WAN Accelerator is not in the direct path between the client and the server. Servers see the IP address of the server-side HP EFS WAN
Accelerator rather than the client IP address, which might impact security policies. An out-of-path configuration is suitable for data center locations where physically in-path or virtually in-path configurations are not possible.
C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable in-path or out-of-path support
For detailed information about in-path and out-of-path deployments, see the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
If you have an HP EFS WAN Accelerator that contains multiple two-port or four-port bypass cards, the Management Console displays options to enable in-path support for these ports. The number of these interface options depends on the number of pairs of
Local Area Network (LAN) and Wide Area Network (WAN) ports that you have enabled in your HP EFS WAN Accelerator.
1. Click the Setup tab to display the Optimization Service - General Settings page.
Figure 2-1. Optimization Service - General Settings Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 23
Control
In-Path
24
2. Use the controls to complete the configuration, as described in the following table.
Description
Enable In-Path Support. Specify this option to enable optimization on traffic that is in the direct path of the client, server, and HP EFS WAN Accelerator.
Reset Existing Client Connections on Startup. Specify this option to enable kickoff. If you enable kickoff, connections that exist when the HP EFS WAN Accelerator service is started and restarted are disconnected. When the connections are retried they are optimized.
Generally, connections are short lived and kickoff is not necessary. It is suitable for very challenging remote environments. For example, in an environment with 128 kbps and 1.5 seconds of latency, you might want to abort an HTTP download so that your traffic is optimized, whereas in a remote branch-office with a T1 and 35 ms round-trip time, you would want connections to migrate to optimization gracefully, rather than risk interruption with kickoff.
NOTE: Do not enable kickoff for in-path HP EFS WAN Accelerators that use autodiscovery or if you do not have an HP EFS WAN Accelerator on the remote side of the network.
Enable L4/PBR/WCCP Support on Interface <interface_name>. Specify this option to enable optional, virtual in-path support on the named interface. External traffic redirection is supported only on the first in-path interface. The following redirection methods are available:
• Layer-4 Switch. You enable Layer-4 switch support when you have multiple HP EFS
WAN Accelerators in your network, so that you can manage large bandwidth requirements.
• Policy-Based Routing (PBR). PBR allows you to define policies to route packets instead of relying on routing protocols. You enable PBR to redirect traffic that you want optimized by an HP EFS WAN Accelerator that is not in the direct physical path between the client and server.
• Web Cache Communication Protocol (WCCP). If your network design requires you to use WCCP, a packet redirection mechanism directs packets to HP EFS WAN
Accelerators that are not in the direct physical path to ensure that they are optimized.
For detailed information about configuring Layer-4 switch, PBR, and WCCP deployments, see the HP StorageWorks Enterprise File Services WAN Accelerator
Deployment Guide.
Enable Optimizations on Interface <interface_name>. Specify this option to enable in-path support for additional bypass cards.
If you have an HP EFS WAN Accelerator that contains multiple two-port or four-port bypass cards, the Management Console displays options to enable in-path support for these ports. The number of these interface options depends on the number of pairs of
LAN and WAN ports that you have enabled in your HP EFS WAN Accelerator.
The interface names for the bypass cards are a combination of the slot number and the port pairs (inpath<slot>_<pair>, inpath<slot>_<pair>). For example, if a four-port bypass card is located in slot 0 of your appliance, the interface names are: inpath0_0 and
inpath0_1. Alternatively, if the bypass card is located in slot 1 of your appliance, the interface names are: inpath1_0 and inpath1_1. The maximum number of pairs is six, which is three four-port bypass cards.
For detailed information about installing additional bypass cards, see the HP
StorageWorks Enterprise File Services N4c WAN Accelerator 4-port NIC Installation
Guide.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Out-of-Path
Connection Limit
Setting In-Path
Rules
Description
Enable Out-of-Path Support. Specify this option to enable out-of-path support. You enable out-of-path support on server-side HP EFS WAN Accelerators only.
NOTE: If you set up an out-of-path configuration with failover support, you must set fixed target rules that specify the master and backup HP EFS WAN Accelerators. For detailed information, see
“Setting In-Path Rules” on page 25 .
Per Source IP Connection Limit. Check this box to limit half-opened connections on a source IP address initiating connections (that is, the client machine). Set this feature to block a source IP address that is opening multiple connections to invalid hosts or ports simultaneously (for example, a virus or a port scanner). This feature does not prevent a source IP address from connecting to valid hosts at a normal rate. Thus a source IP address could have more established connections than the limit. The default value is
4096.
The appliance counts the number of half-opened connections for a source IP address
(connections that check if a server connection can be established before accepting the client connection). If the count is above the limit, new connections from the source IP address are passed through unoptimized.
NOTE: If you have a client connecting to valid hosts or ports at a very high rate, some of its connections might be passed through even though all the connections are valid.
3. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set in-path configuration rules in the Optimization Service - In-Path Rules page.
An in-path rule defines the policies for intercepting traffic on specified ports for optimization.
You can create rules that apply to a single port or to a port label. A port label is a name that you assign to a set of ports so that you can reduce the number of configuration rules in your system. The following port labels are created by default in your system:
Interactive. Automatically passes through traffic on interactive ports (for example, Telnet, TCP ECHO, remote logging, and shell).
Secure. Automatically pass-through traffic on commonly secure ports (for example, ssh, https, and smtps).
RBT-Proto. Specifies well-known ports used by the system: 7800-7801 (in-path),
7810 (out-of-path), 7820 (failover), 7850 (connection forwarding), 7860
(Interceptor appliance).
If you do not want to automatically forward these ports, click Remove Selected Rules in the Optimization Service - In-Path Rules page.
For detailed information about how to configure port labels, see
.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 25
To set an in-path rule
For a list of interactive and secure ports that are automatically forwarded, see
Appendix A, “HP EFS WAN Accelerator Ports.”
1. Click the Setup tab to expand the Optimization Service menu.
2. Click In-Path Rules to display the Optimization Service - In-Path Rules page.
Figure 2-2. Optimization Service - In-Path Rules Page
26 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Rule
3. Use the controls to complete the configuration, as described in the following table.
Description
Type. Select one of the following rule types from the drop-down list:
• Auto-Discovery. Auto-discovery is the process by which the HP EFS WAN
Accelerator automatically intercepts and optimizes traffic on all Internet Protocol (IP) addresses and ports. By default, auto-discovery is applied to all IP addresses and the ports which are not secure or interactive. Defining in-path rules modifies this default setting.
• Fixed-Target. Use fixed-target rules to specify out-of-path HP EFS WAN Accelerators near the target server that you want to optimize. Determine which servers you would like a particular HP EFS WAN Accelerator to optimize (and, optionally, which ports), and add rules to specify the network of servers, ports, port labels, and out-of-path HP
EFS WAN Accelerators to use.
• Pass-Through. Pass-through rules identify traffic that is passed through the network unoptimized. You define pass-through rules to exclude subnets from optimization.
Traffic is also passed through when the HP EFS WAN Accelerator is in bypass mode.
(Pass through might be occur because of in-path rules or because the connection was established before the HP EFS WAN Accelerator was put in place or before the HP
EFS WAN Accelerator service was enabled.)
• Discard. Packets for the connection that match the rule are dropped silently. The HP
EFS WAN Accelerator filters out traffic that matches the discard rules. This process is similar to how routers and firewalls drop disallowed packets: the connection-initiating device has no knowledge of the fact that its packets were dropped until the connection times out.
• Deny. When packets for connections match the deny rule, the appliance actively tries to reset the connection. Deny tells the HP EFS WAN Accelerator to actively try to reset a TCP connection being attempted. Using an active reset process, rather than a silent discard allows the connection initiator to know that its connection is disallowed.
If you have an out-of-path configuration with failover support, you specify the master and backup HP EFS WAN Accelerator in the Optimization Service - In-Path Rules page.
NOTE: In out-of-path deployments, to optimize MAPI Exchange 2003 by destination port, you must define fixed-target, in-path rules that specify the following ports on the client-side HP EFS WAN Accelerator: the Microsoft end-point mapper port: 135; the HP
EFS WAN Accelerator port for Exchange traffic: 7830; the HP EFS WAN Accelerator port for Exchange Directory Name Service Provider Interface (NSPI) traffic: 7840. For detailed information, see
“Optimizing MAPI Exchange in Out-of-Path Deployments” on page 34
.
Source Subnet. Specify the IP address for the source network in the Source Subnet text box. Use the following format: XXX.XXX.XXX.XXX/XX.
Destination Subnet. Specify the IP address for the destination network. Use the following format: XXX.XXX.XXX.XXX/XX.
Port. Specify the destination port number, port label, or all. For detailed information on port labels, see
“Creating Port Labels” on page 113
.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 27
Control
Add New Rule cont.
Description
Insert Rule At. Select start, end, or a rule number from the drop-down list.
HP EFS WAN Accelerators evaluate rules in numerical order starting with rule 1. If the conditions set in the rule match, then the rule is applied, and the system moves on to the next packet. If the conditions set in the rule do not match, the system consults the next rule. For example, if the conditions of rule 1 do not match, rule 2 is consulted. If rule 2 matches the conditions, it is applied, and no further rules are consulted.
In general, you should list rules in the following order:
1. Pass-through. List the exceptions to optimization, first.
2. Fixed-target. List any fixed-targets for optimization, next.
3. Auto-discovery. Apply the default rule: optimize all remaining traffic. (The default auto-discovery rule is listed automatically.)
Add Rule. Specify this option to add the rule to the rules list.
Remove Selected Rules. To remove an entry, click the check box next to the and entry and click Remove Selected Rules.
Move Rule. Use the Move Rule drop-down list and button to change the order in which rules are evaluated.
28 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Advanced Options
Description
VLAN Tag ID. Select the VLAN identification number from the drop-down list to set the VLAN tag identification number (VLAN ID). All specifies the rule applies to all
VLANs; Untagged specifies the rule applies to non-tagged connections.
The HP EFS WAN Accelerator supports VLAN 802.1q. To configure VLAN tagging you perform the following tasks:
• You configure in-path rules to apply to all VLANs or to a specific VLAN. By default, rules apply to all VLAN values unless you specify a particular VLAN ID. Pass-through traffic maintains any pre-existing VLAN tagging between the LAN and WAN interfaces.
• You set the in-path interfaces, VLAN tag IDs to define the VLAN tag that the HP EFS
WAN Accelerator uses to communicate with other HP EFS WAN Accelerator. For
detailed information, see “Setting In-Path Interfaces” on page 54
.
Optimization Policy. Optionally, if you have selected an Auto-Discovery or Fixed
Target rule, you can configure the following types of optimization policies:
• Normal. Perform Lempel-Ziv (LZ) compression and Scalable Data Referencing
(SDR).
• SDR-Only. Perform SDR; do not perform LZ compression.
• Compression-Only. Perform LZ compression; do not perform SDR.
• None. Do not perform SDR or LZ compression.
Setting an optimization policy allows you more flexibility in applying optimization techniques. For example, if you have a network that requires 45 Mbps or higher with abundant bandwidth, you do not need to perform LZ compression to obtain maximum optimization of data. Turning off LZ compression also increases throughput on large bandwidth networks.
To configure optimization policies for the File Transfer Protocol (FTP) data channel, define an in-path rule with the destination port 20 and set its optimization policy. Setting
QoS for port 20 on the client-side HP EFS WAN Accelerator effects passive FTP, while setting the QoS for port 20 on the server-side HP EFS WAN Accelerator effects active
FTP.
To configure optimization policies for the Messaging Application Protocol Interface
(MAPI) data channel, define an in-path rule with the destination port 7830 and set its optimization policy.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 29
Control
Advanced Options cont.
Additional Options
Modifying In-
Path
Descriptions
Description
Neural Framing. Optionally, if you have selected Auto-Discovery or Fixed Target, you can select a neural framing mode for the in-path rule. Neural framing enables the appliance to select the optimal packet framing boundaries for SDR. Neural framing creates a set of heuristics to intelligently determine the optimal moment to flush TCP buffers. The appliance continuously evaluates these heuristics and uses the optimal heuristic to maximize the amount of buffered data transmitted in each flush, while minimizing the amount of idle time that the data sits in the buffer. You can specify the following neural framing settings:
• Never. Never use the Nagle algorithm. All the data is immediately encoded without waiting for timers to fire or application buffers to fill past a specified threshold. Neural heuristics are computed in this mode but are not used.
• Always. Always use the Nagle algorithm. All data is passed to the codec which attempts to coalesce consume calls (if needed) to achieve better fingerprinting. A timer
(6 ms) backs up the codec and causes leftover data to be consumed. Neural heuristics are computed in this mode but are not used.
• Transmission Control Protocol (TCP) Hints. This is the default setting which is based on the TCP hints. If data is received from a partial frame packet or a packet with the TCP PUSH flag set, the encoder encodes the data instead of immediately coalescing it. Neural heuristics are computed in this mode but are not used.
• Dynamic. Dynamically adjust the Nagle parameters. In this option, the HP EFS WAN
Accelerator software discerns the optimum algorithm for a particular type of traffic and switches to the best algorithm based on traffic characteristic changes.
For different types of traffic, one algorithm may be better than others. The considerations include: latency added to the connection, compression, and SDR performance.
To configure neural framing for an FTP data channel, define an in-path rule with the destination port 20 and set its optimization policy. To configure neural framing for a
MAPI data channel, define an in-path rule with the destination port 7830 and set its optimization policy.
Enable Computation of Neural Heuristics. Optionally, check this box to enable optimal packet framing boundaries for SDR.
Update. Click Update to apply your settings to the running configuration.
Remove Selected Rules. To remove an entry, click the check box next to the entry and click Remove Selected Rules.
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You can modify the description of your in-path rules in the Optimization Service - In-
Path Rules Edit page.
30 C ONFIGURING THE HP EFS WAN A CCELERATOR
To modify your in-path rule description
1. Click the Setup tab to expand the Optimization Service menu.
2. Click In-Path Rules to display the Optimization Service - In-Path Rules page.
3. Click Edit Desc in the Rules table to display the Optimization Service - In-Path
Rules Edit page.
Figure 2-3. Optimization Service - In-Path Rules Edit Page
Configuring
CIFS Protocol
Support
4. Modify the description of the rule in the text box and click Update Description.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You configure CIFS protocol support in the Optimization Service - Protocol: CIFS page.
CIFS optimization is enabled by default. Typically, you only disable CIFS optimization to troubleshoot the system.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 31
To configure CIFS protocol options
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Protocol: CIFS to display the Optimization Service - Protocol: CIFS page.
Figure 2-4. Optimization Service - Protocol: CIFS Page
32 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
General
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable Latency Optimization. Latency optimization is enabled by default. Only uncheck this box if you want disable Latency optimization. Typically, you disable latency optimization to troubleshoot problems with the system.
Disable Write Optimization. Specify this option to disable write optimization.
Disable write optimization only if you have applications that assume and require writethrough in the network. If you disable write optimization, the HP EFS WAN Accelerator still provides optimization for CIFS reads and for other protocols, but you might experience a slight decrease in overall optimization.
Most applications operate safely with write optimization because CIFS allows you to explicitly specify write-through on each write operation. However, if you have an application that does not support explicit write-through operations, you must disable it in the HP EFS WAN Accelerator.
If you do not disable write-through, the HP EFS WAN Accelerator acknowledges writes before they are fully committed to disk, to speed up write operation. The HP EFS WAN
Accelerator does not acknowledge the file close until the file is safely written.
Optimize Connections with Security Signatures (that do not require signing).
Specify this option to disable Windows Server Message Block (SMB) signing.
The Secure-CIFS feature enables you to automatically disable Windows Server Message
Block (SMB) signing. SMB signing prevents the appliance from applying full optimization on CIFS connections and significantly reduces the performance gain from an HP EFS WAN Accelerator deployment. Because many enterprises already take additional security precautions (such as firewalls, internal-only reachable servers, and so forth), SMB signing adds little additional security, at a significant performance cost
(even without appliances).
Before you enable Secure-CIFS, you must consider the following factors:
• If the client-side machine has Required signing, enabling Secure-CIFS prevents the client from connecting to the server.
• If the server-side machine has Required signing, the client and server connect but you cannot perform full latency optimization with the appliance. Domain controllers default to Required.
For detailed information about SMB signing and the performance cost associated with it, see the HP StorageWorks Enterprise File Services WAN Accelerator Installation and
Configuration Guide.
Enable Dynamic Write Throttling. Enables CIFS dynamic throttling mechanism which replaces the current static buffer scheme. If you enable CIFS dynamic throttling, it is activated only when there are sub-optimal conditions on the server side causing a backlog of writes messages; it does not have a negative effect under normal network conditions.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 33
Control
Overlapping Open
Configuring
MAPI Protocol
Options
Optimizing MAPI
Exchange in Outof-Path
Deployments
Description
Enable Overlapping Open Optimization. This option is enabled by default. To prevent any compromise to data integrity, the HP EFS WAN Accelerator only optimizes data to which exclusive access is available (in other words, when locks are granted). When an oplock is not available the HP EFS WAN Accelerator does not perform application-level latency optimizations but still performs Scalable Data Referencing (SDR) and compression on the data as well as TCP optimizations. If you disable this feature, the HP
EFS WAN Accelerator will still increase WAN performance, but not as effectively.
Enabling this feature on applications that perform multiple opens of the same file to complete an operation will result in a performance improvement (for example, Computer
Aided Design (CAD) applications):
• Optimize the Following Extensions. Specify a list of extensions you want to optimize using overlapping opens. The default values are: doc, pdf, ppt, sldasm, slddrw,
slddwg, sldprt, txt, vsd, xls.
• Do Not Optimize the Following Extensions. Specify a list of extension you do not want to optimize using overlapping opens. The default values are: ldb, mdb.
NOTE: If a remote user opens a file which is optimized using the overlapping opens feature and a second user opens the same file they might receive an error if the file fails to go through a v3.x HP EFS WAN Accelerator or if it does not go through an HP EFS
WAN Accelerator (for example, certain applications that are sent over the LAN). If this occurs, you should disable overlapping opens for those applications.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You configure MAPI protocol support in the Optimization Service - Protocol: MAPI
Page.
MAPI optimization is enabled by default. Typically, you only disable MAPI optimization to troubleshoot the system.
In out-of-path deployments, if you want to optimize MAPI Exchange by destination port, you must define a fixed-target, in-path rule that specifies the following ports on the client-side appliance:
Port 135. The Microsoft end-point mapper port
Port 7830. The HP EFS WAN Accelerator port used for Exchange traffic
Port 7840. The HP EFS WAN Accelerator port used for Exchange Directory
NSPI traffic
For detailed information about defining in-path rules, see
“To set an in-path rule” on page 26
.
34 C ONFIGURING THE HP EFS WAN A CCELERATOR
To configure MAPI protocol options
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Protocol: MAPI to display the Optimization Service - Protocol: MAPI page.
Figure 2-5. Optimization Service - Protocol: MAPI Page
Control
General
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable MAPI Optimization. MAPI optimization is enabled by default. Only uncheck this box if you want disable MAPI optimization. Typically, you disable MAPI optimization to troubleshoot problems with the system. For example, if you are experiencing problems with
Outlook clients connecting with Exchange, you can disable MAPI latency acceleration
(while continuing to optimize with SDR for MAPI).
Enable MAPI NSPI Optimization. NSPI optimization is enabled by default. Only uncheck this box if you want disable MAPI NSPI optimization. Typically, you disable MAPI NSPI optimization to troubleshoot problems with the system. NSPI is the address book subcomponent of the Exchange protocol that is optimized by the appliance. In certain situations (for example, clients connecting through a firewall), you might want to force a server to listen on a single pre-defined port so that access to ports can be controlled or locked down on the firewall.
NSPI port. Specify the NSPI port.
Enable MAPI Exchange 2003 Acceleration. Specify this option to enable MAPI 2003
Acceleration. This feature increases optimization of traffic between Exchange 2003 and
Outlook 2003.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 35
Control
MAPI Transparent
Pre-population
Description
MAPI Exchange 2003 Port. Specify the MAPI Exchange 2003 port. Typically, you do not need to modify the default value, 7830. If you have changed the Microsoft Exchange
Information Store Interface (MEISI) port in your Exchange Server environment, change port
7830 to the static port number you have configured in your Exchange environment.
For further information about changing (MEISI) ports, see the Microsoft Exchange
Information Store Interface at
http://support.microsoft.com/default.aspx?scid=kb;en-us;270836.
NOTE: For out-of-path deployments, to optimize MAPI Exchange 2003, you must define fixed-target, in-path rules that specify the following ports on the client-side HP EFS WAN
Accelerator: the Microsoft end-point mapper port: 135; the HP EFS WAN Accelerator port for Exchange traffic: 7830; the HP EFS WAN Accelerator port for Exchange Directory NSPI
traffic: 7840. For information on creating a fixed-target, in-path rule, see “Setting In-Path
Enable MAPI Transparent Pre-population. Specify this option to enable MAPI transparent pre-population.
This feature allows email data to be delivered between the Exchange server and the clientside appliance while the Outlook client is off-line. When a user logs into their MAPI client, the mail is already waiting in the client-side appliance and can be retrieved locally. This feature enables email to be optimized even though it has not been seen before by the client.
Max Connections. Specify the maximum number of virtual MAPI connections to the
Exchange server for Outlook clients that have shut down. Setting the maximum connections limits the aggregate load on all Exchange servers through the configured HP EFS WAN
Accelerator. The default value is 325.
You must configure the maximum connections on both the client and server-side of the network.
Poll Interval. Set the number of minutes you want the appliance to poll for shut down clients. The default is 20.
Time-out. Specify the number of hours after which to time-out virtual MAPI connections.
When this threshold is reached, the virtual MAPI connection is terminated. The time-out is enforced on a per-connection basis. Time-out prevents a build up of stale or unused virtual connections over time. The default value is 96.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Configuring MS-
SQL Protocol
Options
You configure MS-SQL protocol support in the Optimization Service - Protocol: MS-
SQL page. Enabling MS-SQL optimization applies default rules to increase optimization for Microsoft Project (MS Project).
The MS-SQL feature also optimizes other database applications, but you must define
SQL rules to obtain maximum optimization. If you are interested in enabling the MS-
SQL feature for other database applications, contact HP professional services.
36 C ONFIGURING THE HP EFS WAN A CCELERATOR
To configure MS-SQL protocol support
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Protocol: MS-SQL to display the Optimization Service - Protocol: MS-SQL page.
Figure 2-6. Optimization Service - Protocol: MS-SQL Page
Control
General
Add MS-SQL Port
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable MS-SQL Optimization. Specify this option to increase optimization for
Microsoft Project.
Enable MS-SQL Prefetch Fetch-Next. Specify this option to enable prefetching requests to request the next row in MS Project. This feature is enabled by default. The server-side appliance prefetches sequential row results and the client-side HP EFS WAN
Accelerator caches them.
Max Number of Pre-Acknowledgements. Specify the number of requests to preacknowledge before waiting for a server response to be returned. The default is 30.
Apply. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
Port. Specify the port number for the MS-SQL server.
Add Port. Click Add Port. The default is 1433.
Remove Selected Ports. To remove an entry, click the check box next to the port name and click Remove Selected Ports.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 37
Enabling the
NFS-
Application
Streamlining
To enable the NFS optimizer
You enable NFS-application streamlining in the Optimization Service - Protocol: NFS page. NFS-application streamlining provides latency optimization improvements for
NFS operations primarily by prefetching data, storing it on the client HP EFS WAN
Accelerator for a short amount of time, and using it to respond to client requests.
You enable NFS-application streamlining where NFS performance over the WAN is impacted by a high latency environment.
NFS file system objects have owners and permissions and NFS-application streamlining conforms to the file system permissions model by enforcing file server and volume policies. You must ensure that the policy is set correctly to Read-Only or
Global Read-Write as appropriate. Setting the policy to Read-Only on a non-read-only file system results in Read-Only file system (ROFS) errors.
1. Click the Setup tab to expand the Optimization Service menu.
1. Click Protocol: NFS to display the Optimization Service - Protocol: NFS page.
Figure 2-7. Optimization Service - Protocol: NFS Page
38 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
General
Add New Server Configuration
2. Use the controls to set NFS options, as described in the following table.
Description
Enable NFS Optimization. Specify this option to enable NFS-application streamlining
(optimization). You enable NFS-application optimization where NFS performance over the WAN is impacted by a high latency environment.
Enable NFS v2 and v4 Alarms. Specify this option to enable alarm notification when v2 and v4 traffic is detected.
Default Server Policy. Select one of the following options from the drop-down list to configure the default policy for NFS servers:
• Global Read-Write. Specifies a policy that provides a trade-off of performance for data consistency. All of the data can be accessed from any client, including LAN based
NFS clients (which do not go through the HP EFS WAN Accelerators) and clients using other file protocols like CIFS. This option severely restricts the optimizations that can be applied without introducing consistency problems. This is the default configuration.
• Custom. Click Custom to display the Enable Root Squashing check box. Click
Enable Root Squashing and Apply to enable the root squash feature for NFS volumes from this server. Root-squashing allows an NFS server to map any incoming user ID 0 or guest ID 0 to another number that does not have superuser privileges, often -2 (the nobody user).
• Home Directory. All accesses to each directory are by a single user. This policy allows aggressive caching of data and metadata.
Default Volume Policy. Select one of the following options from the drop-down list to configure the default policy for NFS volumes:
• Global Read-Write. Specifies a policy that provides a trade-off of performance for data consistency. All of the data can be accessed from any client, including LAN based
NFS clients (which do not go through the HP EFS WAN Accelerators) and clients using other file protocols such as CIFS. This option severely restricts the optimizations that can be applied without introducing consistency problems. This is the default configuration.
• Custom. Click Custom to display the Enable Root Squashing check box. Click
Enable Root Squashing and Apply to enable the root squash feature for NFS volumes from this server. Root-squashing allows an NFS server to map any incoming user ID 0 or guest ID 0 to another number that does not have superuser privileges, often -2 (the nobody user).
• Home Directory. All accesses to each directory are by a single user. This policy allows aggressive caching of data and metadata.
Apply. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
Name. Specify the name of the server to add a new configuration for an NFS server.
Server IP. Specify the IP address of the server and click Add Server.
Remove Selected Servers. To remove an entry, click the check box next to the name and click Remove Selected Servers.
Modifying NFS
Server Settings
You can modify your NFS server configuration settings in the Setup: Optimization
Service - Protocol: NFS Server <server name> page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 39
To modify NFS server settings
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Protocol: NFS to display the Optimization Service - Protocol: NFS page.
3. Click the server name in the NFS Server list to display the Optimization Service -
Protocol: NFS Server <server name> page.
Figure 2-8. Optimization Service - Protocol: NFS Server <server name> Page
40 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Server Settings
Default Volume
Add New Server Configuration
4. Use the controls to complete the configuration, as described in the following table.
Description
Server Policy. Select one of the following options from the drop-down list to configure the default policy for NFS servers:
• Global Read-Write. Specifies a policy that provides a trade-off of performance for data consistency. All of the data can be accessed from any client, including LAN based
NFS clients (which do not go through the HP EFS WAN Accelerators) and clients using other file protocols like CIFS. This option severely restricts the optimizations that can be applied without introducing consistency problems. This is the default configuration.
• Custom. Enables you to turn on or off the root squash feature for NFS volumes from this server.
• Home Directory. All accesses to each directory are by a single user. This policy allows aggressive caching of data and metadata.
Apply. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
Enable Default Volume with Policy. Specify this option and select one of the following options from the drop-down list to configure the default policy for NFS volumes:
• Global Read-Write. Specifies a policy that provides a trade-off of performance for data consistency. All of the data can be accessed from any client, including LAN based
NFS clients (which do not go through the HP EFS WAN Accelerators) and clients using other file protocols like CIFS. This option severely restricts the optimizations that can be applied without introducing consistency problems. This is the default configuration.
• Custom. Enables you to turn on or off the root squash feature for NFS volumes from this server.
• Home Directory. All accesses to each directory are by a single user. This policy allows aggressive caching of data and metadata.
Apply. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
Name. Specify the name of the server to add a new configuration for an NFS server.
Server IP. Specify the IP address of the server and click Add Server.
Remove Selected Servers. To remove an entry, click the check box next to the name and click Remove Selected Servers.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 41
Control
Add New Volume Configuration
Description
FSID. Specify the file system identification number (ID) to add a new NFS volume.
Policy. Select one of the following options from the drop-down list to configure the policy for NFS volumes:
• Global Read-Write. Specifies a policy that provides a trade-off of performance for data consistency. All of the data can be accessed from any client, including LAN based
NFS clients (which do not go through the HP EFS WAN Accelerators) and clients using other file protocols like CIFS. This option severely restricts the optimizations that can be applied without introducing consistency problems. This is the default configuration.
• Custom. Enables you to turn on or off the root squash feature for NFS volumes from this server.
• Home Directory. All accesses to each directory are by a single user. This policy allows aggressive caching of data and metadata.
Enable Root Squash. Select this option to enable root squashing.
Add Volume. Click Add Volume to add the NFS volume to the list.
Remove Selected Volumes. To remove an entry, click the check box next to the name and click Remove Selected Volumes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Enabling
HSTCP Protocol
Options
Task
Enable HSTCP support.
Increase the WAN buffers.
Increase the LAN buffers.
You enable the High Speed Transmission Control Protocol (HSTCP) in the
Optimization Service - Protocol: HSTCP page.
HSTCP provides acceleration and high throughput for high bandwidth networks where the WAN pipe is large but latency is high. HSTCP is activated for all connections that have a Bandwidth-Delay Product (BDP) larger than 100 packets. HSTCP is available only on the Series 5000.
To configure HSTCP you must perform the following tasks.
Description
For detailed information, see “To enable HSTCP protocol support” on page 43 .
Increase the WAN buffers to 2 Bandwidth Delay Product (BDP) or 10 MB. For detailed information, see
“To enable HSTCP protocol support” on page 43 .
You can calculate the BDP WAN buffer size. For example, for a link of 155
Mbps and 100 ms round-trip delay, the WAN buffers should be set to:
2 * 155 Mbps * 100 ms = 3875000 bytes
Increase the LAN buffers to 1 MB. For detailed information, see “To enable
HSTCP protocol support” on page 43 .
42 C ONFIGURING THE HP EFS WAN A CCELERATOR
Task
Enable in-path support.
Disable the Lempel-Ziv (LZ) compression and SDR in in-path optimization policies.
To enable HSTCP protocol support
Description
For detailed information, see “Enabling In-Path and Out-of-Path Support” on page 22
.
For detailed information about optimization policies if your WAN link capacity
is 100 Mbps, see “Setting In-Path Rules” on page 25 .
With SDR enabled your throughput will bottleneck between 100 and 150
Mbps, which cancels out the benefit of HSTCP. If you have an Optical Carrier-
3 line or faster, turning off SDR makes sense and allows HSTCP to reach its full potential. For a 2 Mbps link, regardless of the amount of latency, it is better to keep SDR enabled, because the HSTCP mechanism is typically not triggered until you reach beyond 100 Mbps of WAN throughput.
1. Click the Setup tab to expand the Optimization Service menu.
1. Click Protocol: HSTCP to display the Optimization Service - Protocol: HSTCP page.
Figure 2-9. Optimization Service - Protocol: HSTCP Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 43
Control
High-Speed TCP
Enabling
Connection
Pooling
2. Use the controls to set HSTCP options, as described in the following table.
Description
Enable High Speed TCP. Select this option to enable HSTCP:
• LAN Send Buffer Size. Specify the send buffer size to set the buffer size used to send data out of the LAN. The default value is 81920.
• LAN Receive Buffer Size. Specify the receive buffer size to set the buffer size used to receive data from the LAN. The default value is 32768.
• WAN Default Send Buffer Size. Specify the send buffer size to set the buffer size used to send data out the WAN. The default value is 262140.
• WAN Default Receive Buffer Size. Specify the receive buffer size to set the buffer size used to receive data from the WAN. The default value is 262140.
3. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You configure connection pooling in the Optimization Service - Connection Pooling page.
Connection pooling enhances network performance by reusing active connections instead of creating a new connection for every request. A connection pool manager maintains a pool of open connections. When a new connection request comes in, the pool manager checks if the pool contains unused connections and returns one if available. If all connections currently in the pool are busy and the maximum pool size has not been reached, the new connection is created and added to the pool. When the pool reaches its maximum size all new connection requests are queued up until a connection in the pool becomes available or the connection attempt times out.
Connection pooling is useful for protocols which open a large number of short lived connections, such as HTTP.
Enabling this feature is optional.
44 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable connection pooling
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Connection Pooling to display the Optimization Service - Connection
Pooling page.
Figure 2-10. Optimization Service - Connection Pooling Page
3. Under Connection Pooling Size, type the connection pooling size in the
Maximum Connection Pooling Size text box. The default value is 20.
TIP: To help you determine whether to modify the default, display the Connection Pooling report, described in
“Viewing Connection Pooling” on page 174 . If the report indicates an
unacceptably low ratio of pool hits per total connection requests, increase the pool size.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
IMPORTANT: You must restart the HP EFS WAN Accelerator service on the HP EFS WAN
Accelerator if you have modified your connection pooling parameters. For detailed information
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 45
Enabling
Transparent
Prepopulation
To enable prepopulation settings
You can enable or disable transparent prepopulation in the Optimization Service -
Prepopulation Settings and Shares page.
With transparent prepopulation the HP EFS WAN Accelerator warms the data store with data from the client. When a data store is warm, the HP EFS WAN Accelerator has already seen the data. When data is sent again over the WAN only new or modified data is sent, dramatically increasing the rate of data transfer over the WAN.
After you enable transparent prepopulation you create a share on a remote file server.
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Prepopulation to display the Optimization Service - Prepopulation Settings and Shares page.
3. Click Enable to display the Prepopulation controls.
Figure 2-11. Optimization Service - Prepopulation Settings and Shares Page
46 C ONFIGURING THE HP EFS WAN A CCELERATOR
4. Use the controls to complete the configuration, as described in the following table.
Control
Add a Prepopulation Share
Transparent Prepopulation Using the RCU
Prepopulation Shares
Description
Enable/Disable. Click Enable to enable prepopulation on the share; click Disable to disable prepopulation on the share.
Enable Transparent Pre-population Support. Specify this option to enable transparent pre-population using the HP Copy Utility (RCU).
To enable transparent pre-population using the RCU, you must install and run the RCU on the client and server. Because the data has already been copied to the client and server, the HP EFS WAN Accelerator only copies new data, increasing optimization of traffic across the WAN. The RCU is available for download from the HP Technical Support site at http://www.hp.com.
Apply. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
Save. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Remote Path. The path to the data on the origin server or the Universal Naming
Convention (UNC) path of a share to which you want to make available for prepopulation. For example,
\\<origin-file-server>\<local-name>
NOTE: Do not use guest or anonymous access to a Samba share. Also, the share and the origin-server share name cannot contain Unicode characters. The Management Console does not support Unicode characters.
Account. The local administrator account used to manage prepopulation shares.
Password/Password Confirm. Specify a password. You must use the correct syntax for the administrator login name (for example: admin_user@parent_realm) even if you belong to a subdomain.
Comment. Specify comments to help you identify the share.
Sync Schedule Date and Time. Specify a date and time to schedule synchronization of prepopulation shares with the HP EFS WAN Accelerator. The share conducts automatic synchronization with the origin server based on the synchronization interval.
The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator. Subsequent synchronizations are based on the synchronization interval.
Sync Interval. Interval of updates (synchronization) in minutes. After the initial synchronization, the HP EFS WAN Accelerator retrieves data from the server at every synchronization interval. In these subsequent synchronizations, only new data that was modified or created after the previous synchronization is sent from file server to HP EFS
WAN Accelerator.
5. Click Save to save your settings permanently or click Cancel to return the settings to their previous values.
Enabling and
Synchronizing
Prepopulation
Shares
After you have configured your prepopulation shares, you must perform the initial synchronization of your shares in the Prepopulation Settings and Shares page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 47
To initialize and enable a prepopulation share
When you perform the initial synchronization of the share, a copy of the data is downloaded from the origin server to the HP EFS WAN Accelerator. The HP EFS
WAN Accelerator also configures the share for automatic synchronization according to the parameters you specified previously.
1. Click the Setup tab to display the Optimization menu.
2. Click to Prepopulation to display the Prepopulation Settings and Shares page.
3. Click the Remote Path of the share that you want to initialize in the Prepopulation
Shares list to display the Prepopulation Settings and Shares Details page.
Figure 2-12. Prepopulation Settings and Shares Details Page
48
4. Click Syncing Enable to download the initial copy of the share from the origin server to the HP EFS WAN Accelerator.
5. Click Save to write your changes to disk or Cancel to cancel your settings.
C ONFIGURING THE HP EFS WAN A CCELERATOR
NOTE: When performing the initial synchronization, or when changing large amounts of data, your bandwidth utilization and other graphs may show pockets of inactivity. This is by design.
Modifying
Prepopulation
Share Settings
To modify prepopulation share settings
You can modify your prepopulation share settings in the Prepopulation Settings and
Shares Details page.
1. Click the Setup tab to expand the Optimization menu.
2. Click Prepopulation to display the Prepopulation Settings and Shares page page.
3. Click the Remote Path name in the Prepopulation shares list name that you want to modify to display the Prepopulation Settings and Shares page Details page.
Figure 2-13. Prepopulation Settings and Shares Details Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 49
4. Use the controls to modify your values.
Control Description
Remote Path
Comment
Account
Specify the remote path of the origin file server where the share resides. You must use the Uniform Naming Convention (UNC) for the mapped drive for Version 3 shares. For example, \\<origin-file-server>\<local-name>
IMPORTANT: The prepopulation share and the origin-server share name cannot contain Unicode characters. The Management Console does not support Unicode characters.
Optionally, specify a comment to help you identify the share.
Specify the login to be used to access the shares folder on the origin file server.
IMPORTANT: Make sure the users are members of the Administrators group on the remote share server, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
Password/Password Confirm
Sync Enable
Sync Schedule, Data and Time
Specify and confirm the password to be used to access the shares folder on the origin file server.
Enables a download the initial copy of the share from the origin server to the HP EFS
WAN Accelerator and configure the share for automatic synchronization.
Specify the date and time that you want updates (synchronization) to start. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator. Subsequent synchronizations are based on the synchronization interval.
IMPORTANT: For local mode, changes are synchronized from the HP EFS WAN
Accelerator to the origin file server; broadcast mode changes are synchronized from the origin file server to the HP EFS WAN Accelerator.
Incremental Sync Interval Specify the frequency of updates (synchronization) in minutes.
Full Sync Schedule, Date and Time Specify the date and time that you want updates to start. Use full synchronization if performance is not an issue. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator.
Subsequent synchronizations are based on the synchronization interval.
Full Sync Interval Specify the frequency of updates (synchronization) in minutes.
5. Click Save to save your settings permanently or click Cancel to cancel your settings.
Performing Manual
Actions on
Prepopulation
Shares
You can verify a prepopulation share, perform a full synchronization, cancel an operation, or delete a prepopulation share in the Prepopulation Shares list. The shares list appears on the Prepopulation Settings and Shares Details page.
50 C ONFIGURING THE HP EFS WAN A CCELERATOR
To perform manual actions on prepopulation shares
1. Click the Setup tab to expand the Optimization menu.
2. Click Prepopulation to display the Prepopulation Settings and Shares page.
3. Click the Remote Path name in the Prepopulation shares list name that you want to modify to display the Prepopulation Settings and Shares Details page.
Figure 2-14. Prepopulation Settings and Shares Details Page
Control
Actions
4. Select one of the following actions for the prepopulation share, as described in the following table.
Description
Select one of the following actions from the drop-down list:
• Start Full Sync. Allows you to immediately synchronize the share and its corresponding remote share on the origin file server. You may select Start Full Sync at any time to manually synchronize a share.
• Cancel Action. Cancels the synchronization process.
• Delete Share. Deletes the selected share.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 51
Setting the
Primary
Interface
Setting Host Parameters
This section describes how to set host parameters for the HP EFS WAN Accelerator.
It includes the following sections:
“Setting the Primary Interface,” next
“Setting In-Path Interfaces” on page 54
“Setting Auxiliary Interfaces” on page 58
“Setting Main Static Routes” on page 59
“Setting Static In-Path Routes” on page 60
“Modifying the Host Name” on page 63
“Mapping Hosts to IP Addresses” on page 63
You modify settings for the primary interface in the Host Settings - Interface Primary page.
You were prompted to configure the primary interface when you completed the installation wizard. This section describes how you can modify these settings.
IMPORTANT: The primary and in-path interfaces can share the same subnet. The primary and auxiliary interfaces cannot share the same network subnet.
52 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set the primary interface
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to display the Host Settings - Interface: Primary page.
Figure 2-15. Host Settings - Interface Primary Page
Control
IP Address
3. Use the controls to complete the configuration, as described in the following table.
Description
Obtain IP address automatically. Specify this option to automatically obtain the IP address from a Dynamic Host Configuration Protocol DHCP server. (A DHCP server must be available so that the HP EFS WAN Accelerator can request the IP address from it.)
IMPORTANT: The primary and in-path interfaces can share the same subnet. The primary and auxiliary interfaces cannot share the same network subnet.
Specify IP Address Manually. Specify this option if you do not use a DHCP server to set the IP address. Specify the following settings:
• IP Address. Specify an IP address.
• Subnet Mask. Specify a subnet mask.
• Primary Gateway. Specify the primary gateway IP address. The primary gateway must be in the same network as the primary interface. You must set the primary gateway for in-path configurations.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 53
Control
Additional Interface Settings
Description
Speed. Select the speed from the drop-down list. The default value is Auto .
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same speed settings.
Duplex. Select Auto, Full or Half from the drop-down list. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same duplex settings.
MTU. Specify the Maximum Transmission Unit (MTU) value. The MTU is the largest physical packet size, measured in Bytes, that a network can transmit. The default value is
1500.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous value.
Setting In-Path
Interfaces
You modify the settings for the in-path interface in the Host Settings - Interface: In-
Path (LAN/WAN) page.
You specify the in-path interface if you plan to have the appliance in the direct path
(the same subnet) as the client and the server in your network. You also set the in-path gateway (WAN router).
NOTE: You were prompted to configure the in-path interface when you completed the installation wizard. This section describes how you can modify these settings.
Speed and Duplex
Tips
If your network routers do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the in-path interface (that is, the HP EFS WAN
Accelerator).
Speed and duplex mismatches can easily occur in a network. For example, if one end of the link is set at half or full-duplex and the other end of the link is configured to auto negotiate (auto), the link defaults to half-duplex, regardless of the duplex setting on the non-auto-negotiated end. This duplex mismatch passes traffic, but it causes interface errors and results in degraded optimization.
The following are general guidelines to avoid speed and duplex mismatches when configuring the HP EFS WAN Accelerator:
54 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set the in-path interface
Routers are often configured with fixed speed and duplex settings. Check your router configuration and set it to match the HP EFS WAN Accelerator WAN and
LAN settings. Make sure your switch has the correct setting.
After you finish configuring the HP EFS WAN Accelerator, check for speed and duplex error messages (crc or frame errors) in the Logging, View System Log page of the Management Console. For detailed information about viewing HP
EFS WAN Accelerator logs, see
“Viewing HP EFS WAN Accelerator Logs” on page 201 .
If there is a serious problem with the HP EFS WAN Accelerator and it goes into bypass mode (that is, it automatically continues to pass traffic through your network), a speed and duplex mismatch might occur when you reboot the HP EFS
WAN Accelerator. To avoid a speed and duplex mismatch, configure your LAN external pair to match the WAN external pair. For example, auto on the LAN and
WAN and fixed to 100 FULL on the LAN and WAN.
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Interface: In-Path to display the Host Settings - Interface: In-Path (LAN/
WAN) page.
Figure 2-16. Host Settings - Interface: In-Path (LAN/WAN) Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 55
Control
IP Address
4. Use the controls to complete the configuration, as described in the following table.
Description
Obtain IP address automatically. Specify this option to obtain the IP address from a
DHCP server.
IMPORTANT: The primary and in-path interfaces can share the same subnet. The primary and auxiliary interfaces cannot share the same network subnet.
Specify IP Address Manually. Specify this option if you do not use a DHCP server to set the IP address. Specify the following settings:
• IP Address. Specify an IP address. This IP address is the in-path main interface.
• Subnet Mask. Specify the subnet mask.
• In-Path Gateway IP. Specify the IP address for the in-path gateway. If you have a router (or a Layer-3 switch) on the LAN side of your network, specify this device as the in-path gateway.
IMPORTANT: If there is a routed network on the LAN-side of the in-path appliance, the router that is the default gateway for the appliance must not have the Access Control List
(ACL) configured to drop packets from the remote hosts as its source. The in-path appliance uses IP masquerading to appear as the remote server.
56 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Additional Interface Settings
VLAN
Description
LAN Speed. Select the speed from the drop-down list to set the speed for the in-path
LAN port. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same settings.
Duplex. Select Auto, Full, or Half from the drop-down list to set the duplex speed for the in-path LAN port. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same settings.
WAN Speed. Select the speed from the drop-down list to set the speed for the in-path
WAN port. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same settings.
Duplex. Select Auto, Full, or Half from the drop-down list to set the duplex speed for the in-path WAN port. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must manually set the speed and duplex for the primary interface.
The speed and duplex must match (LAN and WAN) in an in-path configuration. If they do not match you might have a large number of errors on the interface when it is in bypass mode, because the switch and router are not set with the same settings.
MTU. Specify the Maximum Transmission Unit (MTU) value. The MTU is the largest physical packet size, measured in Bytes, that a network can transmit. The default value is
1500.
VLAN Tag ID. If you have enabled VLAN tagging, type a numeric ID. Specify 0 to leave the interface untagged.
When you specify the VLAN Tag ID for the in-path interface, all packets originating from the HP EFS WAN Accelerator are tagged with that identification number. This is the
VLAN tag that the appliance uses to communicate with other HP EFS WAN Accelerators in your network. The VLAN Tag ID might be the same value or a different value than the
VLAN tag used on the client. A zero (0) value specifies non-tagged (or native) VLAN.
NOTE: When the HP EFS WAN Accelerator communicates with a client or a server it uses the same VLAN tag as the client or the server. If the HP EFS WAN Accelerator cannot determine which VLAN the client or server is in, it uses its own VLAN until it is able to determine that information.
NOTE: You must also define in-path rules to apply to your VLANs. For detailed
information, see “Setting In-Path Rules” on page 25 .
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 57
Setting
Auxiliary
Interfaces
To set an auxiliary interface
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set up an auxiliary interface, which provides support if your network has a dedicated management subnet, in the Host Settings - Interface: AUX page. For example, if your network has an auxiliary interface that connects and passes packets between the HP EFS WAN Accelerator and a different network, such as one purely for device management.
IMPORTANT: The primary and auxiliary interfaces cannot share the same network subnet.
The auxiliary and in-path interfaces cannot share the same subnet.
Enabling this interface is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Interface: AUX to display the Host Settings - Interface: AUX page.
Figure 2-17. Host Settings - Interface: AUX Page
58 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
AUX Interface Enabled
IP Address
Additional Interface Settings
4. Use the controls to complete the configuration, as described in the following table.
Description
Select Enabled or Disabled from the drop-down list.
IMPORTANT: The primary and auxiliary interfaces cannot share the same network subnet. The auxiliary and in-path interfaces cannot share the same subnet. You cannot use the auxiliary port for out-of-path HP EFS WAN Accelerators.
Obtain IP address automatically. Specify this option to obtain the IP address from a dynamic host configuration protocol (DHCP) server.
Specify IP Address Manually. Specify this option if you do not use a DHCP server to set the IP address. Specify the following settings:
• IP Address. Specify an IP address.
• Subnet Mask. Specify the subnet mask.
Speed. Select the speed from the drop-down list to set the speed for the auxiliary interface. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must set the speed and duplex manually.
Duplex. Select Auto, Full, or Half from the drop-down list to set the duplex speed for the auxiliary interface. The default value is Auto.
If your network routers or switches do not automatically negotiate the speed and duplex, you must set the speed and duplex manually.
MTU. Specify the Maximum Transmission Unit (MTU) value. The MTU is the largest physical packet size, measured in Bytes, that a network can transmit. The default is 1500.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Main
Static Routes
You set static routes for device management or out-of-path network configurations in the Host Settings - Routing: Main page.
Main static network routes set routing rules in the main routing table for the primary interface.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 59
To set a static main route
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Routing: Main to display Host Settings - Routing: Main page.
Figure 2-18. Host Settings - Routing: Main Page
Control
Add New Route
Setting Static
In-Path Routes
60
4. Use the controls to complete the configuration, as described in the following table.
Description
Destination. Specify the IP address.
Netmask. Specify the subnet mask.
Gateway. Specify the IP address for the gateway. The gateway must be in the same network as the primary or auxiliary interface.
Add Route. Specify this option to add the entry to the list.
Remove Selected Routes. To remove an entry, click the check box next to the entry and click Remove Selected Routes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You configure static, in-path network routes if your network configuration requires additional static in-path network routing rules in the Host Settings - Routing: In-Path page.
The values you specify set the routing table for in-path interfaces (as opposed to the primary interface).
C ONFIGURING THE HP EFS WAN A CCELERATOR
To set a static, in-path route
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Routing: In-Path to display the Host Settings - In-Path Routing page.
Figure 2-19. Host Settings - In-Path Routing Page
Control
Add New Route
4. Use the controls to complete the configuration, as described in the following table.
Description
Destination. Specify the IP address.
Netmask. Specify the subnet mask.
Gateway. Specify the IP address for the gateway. The gateway must be in the same network as the primary or auxiliary interface.
Add Route. Specify this option to add the entry to the list.
Remove Selected Routes. To remove an entry, click the check box next to the entry and click Remove Selected Routes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting the DNS
You set the primary Domain Name Service (DNS) server and domain for the HP EFS
WAN Accelerator in the Host Settings - DNS Settings page.
HP recommends you use DNS.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 61
NOTE: You were prompted to configure DNS when you completed the installation wizard.
This section describes how you can modify these settings.
To set the DNS server 1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click DNS Settings to display the Host Settings - DNS Settings page.
Figure 2-20. Host Settings - DNS Settings Page
Control
Name Servers
Domain Search
62
4. Use the controls to complete the configuration, as described in the following table.
Description
Set one or more of the following:
• Primary DNS IP. Specify the IP address for the primary name server.
• Secondary DNS IP. Optionally, specify the IP address for the secondary name server.
• Tertiary DNS IP. Optionally, specify the IP address for the tertiary name server.
To apply your settings, click Set Name Servers.
Add Domain. Specify the domain name and click Add Domain. If you specify domains the HP EFS WAN Accelerator automatically finds the appropriate domain for each of the hosts that you enter in the system.
Remove Selected Domain. To remove an entry, click the box next to the domain name and click Remove Selected Domain.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Modifying the
Host Name
To modify the host name
You can change the host name for the HP EFS WAN Accelerator in the Host Settings
- Host Name page.
NOTE: You were prompted to specify a host name when you completed the installation wizard.
This section describes how you can modify these settings.
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Host Name to display the Host Settings - Host Name page.
Figure 2-21. Host Settings - Host Name Page
4. Modify the text in the Host Name text box to change the host name.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Mapping Hosts to IP Addresses
You can map a host name to IP addresses in the Host Settings - Hosts page.
Specify these values only if you are not using DNS to resolve host names and IP addresses in your system (or if the host does not have a DNS entry).
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 63
To map a host name to an IP address
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Hosts to display the Host Settings - Hosts page.
Figure 2-22. Host Settings - Hosts Page
Control
Add New Host
4. Use the controls to complete the configuration, as described in the following table.
Description
Host IP. Specify the IP address for the host.
Host name. Specify a host name.
Add Entry. Click Add Entry to add a host and IP address.
Remove Selected Hosts. To remove an entry, click the check box next to the name and click Remove Selected Hosts.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Proxies
You can specify a Web or FTP proxy in the Host Settings - Proxies page.
This proxy is used when a Uniform Resource Locator (URL) is specified in the
Management Console or the CLI. For example, the proxy is used in the Software
Upgrade page if you specify a URL from which to download the software image.
This setting applies only if you specify FTP or HTTP in the URL.
64 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable a proxy
Setting proxies is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Host Settings to expand the Host Settings menu.
3. Click Proxies to display the Host Settings - Proxies page.
Figure 2-23. Host Settings - Proxies Page
Control
Web/FTP Proxy IP Address
Port
4. Use the controls to complete the configuration, as described in the following table.
Description
Specify the IP address for the Web/FTP proxy.
Specify the port number for the Web/FTP proxy.
5. Click Apply to apply your settings to the running configuration.
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Advanced Network Parameters
This section describes how to configure advanced network parameters in the HP EFS
WAN Accelerator. It includes the following sections:
“Enabling Asymmetric Routing Auto-Detection,”
next
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 65
Enabling
Asymmetric
Routing Auto-
Detection
“Enabling Connection Forwarding” on page 68
“Enabling Encryption” on page 70
“Enabling Failover and Data Store Synchronization” on page 73
“Setting Peering Rules” on page 79
“Enabling Quality of Service” on page 81
“Modifying a QoS Class” on page 85
“Setting QoS Marking” on page 87
“Modifying QoS Marking Descriptions” on page 89
“Modifying Service Ports” on page 90
“Enabling Simplified Routing” on page 92
“Enabling WCCP Groups” on page 94
“Modifying WCCP Group Settings” on page 96
You enable asymmetric route auto-detection in the Advanced Networking -
Asymmetric Routing page. Asymmetric route auto-detection detects and reports asymmetric routing conditions and caches this information to avoid losing connectivity between a client and a server.
When HP EFS WAN Accelerators are deployed in a network, all TCP traffic must flow through the same HP EFS WAN Accelerators in the forward and reverse direction. If traffic flows through an HP EFS WAN Accelerator in one direction and not the other, then TCP clients are unable to make connections to TCP servers. When deploying HP
EFS WAN Accelerators into redundant networks, there is a possibility of traffic taking different forward and return paths so that traffic in one direction goes through HP EFS
WAN Accelerators but traffic in the reverse direction does not.
If asymmetric routing is detected, the pair of IP addresses, defined by the client and server addresses of this connection, is cached on the HP EFS WAN Accelerator.
Further connections between these hosts are not optimized until that particular asymmetric routing cache entry times out.
Detecting and caching asymmetric routes does not optimize these packets. If you want to optimize asymmetric routed packets you must make sure that packets going to the
WAN always go through an HP EFS WAN Accelerator either by using a multi-port HP
EFS WAN Accelerator, connection forwarding, or using external ways to redirect packets, such as WCCP or PBR.
For detailed information, see
“Enabling Connection Forwarding” on page 68 or the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
66 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable asymmetric routing auto-detection
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to display Advanced Networking - Asymmetric
Routing page.
Figure 2-24. Advanced Networking - Asymmetric Routing Page
Control
General Settings
Source IP Table
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable Asymmetric Routing Detection. Specify this option to detect asymmetric routes in your network.
Enable Asymmetric Routing Caching. Specify this option to enable the asymmetric routing cache in the HP EFS WAN Accelerator. If asymmetric routing is detected, the pair of IP addresses, defined by the client and server addresses of this connection, is cached on the HP EFS WAN Accelerator. Further connections between these hosts are not optimized until that particular asymmetric routing cache entry times out.
Detecting and caching asymmetric routes does not optimize these packets. If you want to optimize asymmetric routed packets you must make sure that packets going to the WAN always go through an HP EFS WAN Accelerator either by using a multi-port HP EFS
WAN Accelerator, connection forwarding, or using external ways to redirect packets, such as WCCP or PBR.
For detailed information, see
“Enabling Connection Forwarding” on page 68 or the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
Apply. Click Apply to apply your settings to the running configuration.
Remove Selected Entries. To remove an entry, click the check box next to the name and click Remove Selected Entries.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 67
Enabling
Connection
Forwarding
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You enable connection forwarding in a network configuration with multiple paths from the server in the Advanced Networking - Connection Forwarding page.
You enable connection forwarding only in asymmetric networks; that is, in networks in which a client request traverses a different network path than the server response.The default port for connection forwarding is 7850.
To optimize connections in asymmetric networks, packets traveling in both directions must pass through the same client-side and server-side HP EFS WAN Accelerator. If you have one path from the client to the server and a different path from the server to the client, you need to enable in-path connection forwarding and configure the HP EFS
WAN Accelerators communicate with each other. These HP EFS WAN Accelerators are called neighbors and exchange connection information to redirect packets to each other.
Figure 2-25. Asymmetric Network
68
Neighbors can be placed in the same physical site or in different sites but the latency between them should be small because the packets travelling between them are not optimized.
IMPORTANT: When you define a neighbor, you specify the HP EFS WAN Accelerator in-path
IP address, not the primary IP address.
If there are more than two possible paths, additional HP EFS WAN Accelerators must be installed on each path and configured as neighbors. Neighbors are notified in parallel so that the delay introduced at connection set up is equal to the time it takes to get an acknowledgement from the furthest neighbor.
For detailed information about connection forwarding, see the HP StorageWorks
Enterprise File Services WAN Accelerator Deployment Guide.
C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable connection forwarding
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu and display the Advanced Networking -Connection Forwarding page.
Figure 2-26. Advanced Networking - Connection Forwarding Page
Control
General
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable Connection Forwarding. Specify this option to enable connection forwarding by default on all neighbors added to the peer list. The default port for connection forwarding is 7850.
Port. Specify the port number to use as the default for neighbor appliance in-path port.
The default is 7850.
Keep-Alive Interval. Specify the number of seconds to use as the default interval for
ping commands between neighbor appliances.
Keep-Alive Count. Specify the number of tries to use as the default number of failed
ping attempts before an appliance terminates a connection with a neighbor. The default value is 3.
Apply. Click Apply to apply them to entries in the peer list.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 69
Control
Add New Entry
Enabling
Encryption
Description
Neighbor IP. Specify the in-path IP address for the neighbor appliance. When you define a neighbor, you must specify the appliance in-path IP address, not the primary IP address.
Neighbor Port. Specify the in-path port for the neighbor appliance. The default is 7850.
Add Peer. Click Add Peer to add a neighbor to the peer list.
Remove Selected Entries. To remove an entry, select it and click Remove Selected
Entries.
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You configure IP Security Protocol (IPsec) encryption to allow data to be communicated securely between peer HP EFS WAN Accelerators in the Advanced
Networking - Encryption page.
Enabling IPsec encryption makes it difficult for a third party to view your data or pose as a machine you expect to receive data from. To enable IPsec, you must specify at least one encryption and authentication algorithm. Only optimized data is protected, pass-through traffic is not.
Enabling IPsec support is optional.
IMPORTANT: You must set IPsec support on each peer HP EFS WAN Accelerator in your network for which you want to establish a secure connection. You must also specify a shared secret on each peer HP EFS WAN Accelerator.
NOTE: If you Network Address Translate (NAT) traffic between HP EFS WAN Accelerators, you cannot use the IPSEC channel between the appliances because the NAT changes the packet headers causing IPSEC to reject them.
70 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable encryption 1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click Encryption to display the Advanced Networking - Encryption page.
Figure 2-27. Advanced Networking - Encryption Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 71
Control
General
Add New Peer
72
4. Use the controls to complete the configuration, as described in the following table.
Description
Check one or more of the following options:
• Enable Authentication and Encryption. Specify this option to enable authentication between appliances.
• Enable Perfect Forward Secrecy. Specify this option if you want to provide additional security by renegotiating keys at specified intervals. Perfect Forward
Secrecy provides additional security by renegotiating keys at specified intervals. If one key is compromised, subsequent keys are secure because they are not derived from previous keys.
Encryption Policy. Select one of the following methods from the Method 1 drop-down list:
• DES. Data Encryption Standard. DES is the default value.
• NULL. Specifies the null encryption algorithm.
Set encryption algorithms in order of priority. The algorithm is used to encrypt each packet sent using IPsec.
Optionally, select DES, NULL, or None from the Method 2 drop-down list.
Authentication Policy. Select one of the following authentication methods from the
Method One drop-own list:
• MD5. Message-Digest algorithm. MD5 is a widely-used cryptographic hash function with a 128-bit hash value. MD5 is the default value.
• SHA-1. Secure Hash Algorithm. SHA-1 is a set of related cryptographic hash functions. SHA-1 is considered to be the successor to MD5.
Optionally, select MD5, SHA-1, or None from the Method Two drop-down list.
Time Between Key Renegotiations. Specify the number of minutes between quickmode renegotiation of keys using Internet Key Exchange (IKE). IKE uses public key cryptography to provide the secure transmission of a secret key to a recipient so that the encrypted data can be decrypted at the other end. The default value is 240 minutes.
Enter the Shared Secret/Confirm the Shared Secret. Specify the shared secret. All the
HP EFS WAN Accelerators in a network for which you want to use IPsec must have the same shared secret.
Apply. Click Apply to apply your settings to the running configuration.
Peer IP. Specify the IP address for the peer HP EFS WAN Accelerator for which you want to make a secure connection.
Add Peer. Click Add Peer to add the peer specified in the Peer IP text box.
If IPsec is enabled on this HP EFS WAN Accelerator, then it must also be enabled on all appliances in the IP security peers list; otherwise this HP EFS WAN Accelerator will not be able to make optimized connections with those peers.
If a connection has not been established between the two HP EFS WAN Accelerators that are configured to use IPsec security, the Peers list does not display the peer HP EFS WAN
Accelerator because a security association has not been established.
Remove Selected Peers. To remove an entry, click the check box next to the name and click Remove Selected Peers.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Enabling Failover and Data Store
Synchronization
You enable failover and automatic data store synchronization support in the Advanced
Networking - Failover Settings page.
Failover support ensures continued optimization if there is a failure with one of the HP
EFS WAN Accelerators. If the master HP EFS WAN Accelerator fails, the traffic is automatically processed by the backup HP EFS WAN Accelerator.
Automatic data store synchronization replicates the data store from an active HP EFS
WAN Accelerator to a passive HP EFS WAN Accelerator without disrupting operations. Data store synchronization ensures that a warm data store exists on the backup HP EFS WAN Accelerator. With a warm data store, the backup HP EFS WAN
Accelerator can perform as optimally as its master when it is activated; that is, it performs as if it has seen the data before and only sends new segments across the
WAN.
NOTE: Data is replicated only from the master HP EFS WAN Accelerator to the backup; not vice versa.
NOTE: All operations occur in the background and do not disrupt operations on any of the systems.
Enable data store synchronization if you have:
Simple Redundancy. A network in which two HP EFS WAN Accelerators have been deployed in a failover configuration.
Router Redundancy. A network where there two or more routers at a remote site and HP EFS WAN Accelerators are deployed behind each router for redundancy.
Complex Router Redundancy. A network where serially connected HP EFS
WAN Accelerators containing multi-port cards that connect to multiple routers on each side of the network.
Virtual In-Path and Out-of-Path. An out-of-path deployment or a virtual inpath deployment using WCCP, PBR, or a Layer-4 switch.
Serial Cluster. A network where several HP EFS WAN Accelerators are deployed back-to-back in an in-path configuration.
Enabling failover and data synchronization support is optional.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 73
To enable failover and data store synchronization
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click Failover Settings to display the Advanced Networking - Failover Settings page.
Figure 2-28. Advanced Networking - Failover Settings Page
74 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Failover Settings
4. Use the controls to complete the configuration, as described in the following table.
Description
Enable Failover Support. Specify this option to enable failover support.
Current Appliance is the. Select Master or Backup from the drop-down list. A master
HP EFS WAN Accelerator is the primary appliance; the backup HP EFS WAN
Accelerator is the appliance that automatically optimizes traffic if the master appliance fails. You must specify the primary IP address for the backup appliance.
IMPORTANT: If you have multiple bypass cards installed in your appliance you must specify the inpath0_0 interface for the in-path IP address.
NOTE: If you have an out-of-path configuration with failover support, you must specify the master and backup appliances in the Optimization Service - In-Path Rules page. For detailed information, see
“Setting In-Path Rules” on page 25 .
Other Appliance’s In-path IP Address. Specify the IP address for the master or backup
HP EFS WAN Accelerator. You must specify the in-path IP address (inpath0_0) for the
HP EFS WAN Accelerator, not the primary interface IP address.
IMPORTANT: If you have multiple bypass cards installed in your HP EFS WAN
Accelerator you must specify the inpath0_0 interface for the in-path IP address.
For detailed information, see
“Setting In-Path Interfaces” on page 54
.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 75
Control
Automated Online Datastore
Settings
Description
Enable Automated Online Datastore Synchronization. Specify this option to enable automated data store synchronization. Data store synchronization ensures that each data store in your network has warm data for maximum optimization. All operations occur in the background and do not disrupt operations on any of the systems.
There are the following phases in synchronization:
• Catchup. Copies data that is already on the master to the backup HP EFS WAN
Accelerator. This process stops when all the old data from the master is copied to the backup HP EFS WAN Accelerator.
• Keepup. Runs continuously copying new data that the master appliance encounters to the backup HP EFS WAN Accelerator.
IMPORTANT: The HP EFS WAN Accelerators must be the same model; models running different versions of the software will not synchronize (for example v2.x to 3.x).
Synchronization does not guarantee that all data objects are replicated—synchronization runs in the background, if the HP EFS WAN Accelerator is under load, all data may not be replicated.
NOTE: If you are setting up automated data store synchronization for the first time, the
HP EFS WAN Accelerator service is halted on the backup HP EFS WAN Accelerator.
You must restart the HP EFS WAN Accelerator service on backup HP EFS WAN
Accelerators. If you restart the service with a clean data store you must shutdown the backup HP EFS WAN Accelerator, power it off, and power it on.
NOTE: In out-of-path configurations, you must designate an HP EFS WAN Accelerator as a backup appliance, either by enabling failover support or by designating it as an outof-path backup appliance, to implement data store synchronization.
Current Appliance is the. Select Master or Backup from the drop-down list. You must specify the primary IP address for the master and backup appliance.
IMPORTANT: If you have multiple bypass cards installed in your appliance you must specify the inpath0_0 interface.
Other Appliance’s In-path IP Address. Specify the backup or master HP EFS WAN
Accelerator IP address. You must specify the primary IP address for the master and backup appliance.
You must specify the primary (or AUX if you have enabled this option) IP address for the
HP EFS WAN Accelerator. For detailed information, see “Setting the Primary Interface” on page 52 .
IMPORTANT: If you have multiple bypass cards installed in your appliance you must specify the inpath0_0 interface.
Synchronization Port. Specify the port number for the HP EFS WAN Accelerator from which you want to replicate data. The default value is 7744.
Reconnection interval. Specify the number of seconds. The default value is 30.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
76 C ONFIGURING THE HP EFS WAN A CCELERATOR
Enabling
NetFlow
NOTE: If you are setting up automated data store synchronization for the first time, you must restart the HP EFS WAN Accelerator service on both the master and the backup HP EFS WAN
Accelerators to initialize data store synchronization. For detailed information about restarting the HP EFS WAN Accelerator service, see the
“Starting and Stopping Services” on page 144
.
NOTE: In an out-of-path configuration, to implement failover support, you must also specify a fixed target rule that specifies both master and backup target appliances. For detailed information, see
“Setting In-Path Rules” on page 25 .
You enable and configure NetFlow support in the Advanced Networking - NetFlow
Export page.
NetFlow enables you to export network statistics that provide information about network users and applications, peak usage times, and traffic routing. NetFlow records information for each packet ingressing the specified network interface. This data is then sent to a NetFlow collector, a software package provided by a third party vendor or an open source.
IMPORTANT: Enabling NetFlow could adversely impact HP EFS WAN Accelerator performance and increase bandwidth utilization.
Enabling NetFlow support is optional.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 77
To enable NetFlow support
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click NetFlow to display the Advanced Networking - NetFlow Export page.
Figure 2-29. Advanced Networking - NetFlow Export Page
Control
General
4. Use the controls to complete the configuration, as described in the following table.
Description
Enable NetFlow Export. Specify this option to enable NetFlow support.
Apply. Click Apply to apply your settings to the running configuration.
78 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Entry
Description
Collector IP. Specify the IP address for the NetFlow collector.
Collector Port. Specify the port the NetFlow collector is listening on. The default value is 2055.
Capture. Select Optimized, Passthrough, or All from the drop-down list. Specifies whether optimized, pass through, or all traffic is exported to the NetFlow collector. The default value is Optimized.
Export Interface. Select aux or primary from the drop-down list. NetFlow records sent from the HP EFS WAN Accelerator will appear to be sent from the IP address of the selected interface.
Show LAN Address. Specify this option if the TCP IP addresses and ports reported for optimized flows should contain the original client and server IP addresses and not those of the HP EFS WAN Accelerator. The default is to show the IP addresses of the original client and server without the IP address of the HP EFS WAN Accelerators.
Capture Interface. Select from the drop-down list the interface on which NetFlow should track flows.
Additional Interface. Click the Additional interface to display an additional Capture
Interface drop-down list.
Add Collector. Click Add Collector to add the collector to the Collector list.
Remove Selected Entries. To remove an entry, click the check box next to the name and click Remove Selected Peers.
Setting Peering
Rules
You set peering relationships among HP EFS WAN Accelerators in the Advanced
Networking - Peering Rules page. Serial clusters are supported only on Series 5000s.
You can configure peering rules that apply to a single port or you can configure peering rules that apply to a port label. A port label is a label that you assign to a set of ports so that you can reduce the number of configuration rules in your system. For detailed
information about how to configure port labels, see “Creating Port Labels” on page 113
.
Enabling Peering
Rules for Serial
Clustering
You can provide increased optimization by deploying several HP EFS WAN
Accelerators back-to-back in an in-path configuration to create a serial cluster. For detailed information, see the HP StorageWorks Enterprise File Services WAN
Accelerator Deployment Guide.
Appliances in a cluster process the peering rules you specify in a spill-over fashion.
When the maximum number of TCP connections for an HP EFS WAN Accelerator is reached, that appliance stops intercepting new connections and passes them on to the next HP EFS WAN Accelerator in the cluster (as defined by the peer rule that you set).
In serial cluster deployments:
The peering rules table is a ordered list of rules and the first rule that matches the rule is applied.
To avoid interceptions on inner connections created by other appliances in the same cluster, in-path rules are specified to pass-through connections originating from those appliances.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 79
To set a peering rule
Setting peering rules to enable serial clustering is optional.
IMPORTANT: HP strongly recommends that only Series 5000s are deployed in a serial cluster due to traffic loads.
For detailed information about serial cluster deployments and peering rules, see the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click Peering Rules to display the Advanced Networking - Peering Rules page.
Figure 2-30. Advanced Networking - Peering Rules Page
80 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Rule
Enabling
Quality of
Service
4. Use the controls to complete the configuration, as described in the following table.
Description
Type. Select one of the following rule types from the drop-down list:
• Auto. Allows built-in functionality to determine the response for peering requests
(performs the best peering possible).
• Accept. Accepts peering requests that match the source-destination-port pattern.
• Pass. Allows pass-through peering requests that match the source and destination port pattern.
You can configure peering rules that apply to a single port or you can configure peering rules that apply to a port label. A port label is a label that you assign to a set of ports so that you can reduce the number of configuration rules in your system. For detailed information about how to configure port labels, see
“Creating Port Labels” on page 113
.
Insert Rule At. Select start, end, or a rule number from the drop-down list.
HP EFS WAN Accelerators evaluate rules in numerical order starting with rule 1. If the conditions set in the rule match, then the rule is applied, and the system moves on to the next packet. If the conditions set in the rule do not match, the system consults the next rule. For example, if the conditions of rule 1 do not match, rule 2 is consulted. If rule 2 matches the conditions, it is applied, and no further rules are consulted.
Source Subnet. Specify the IP address for the source network. Use the following format:
XXX.XXX.XXX.XXX/XX.
Destination Subnet. Specify the IP address for the destination subnet. Use the following format: XXX.XXX.XXX.XXX/XX.
Port. Specify the destination port number, port label, or all. For detailed information on port labels, see
“Creating Port Labels” on page 113
.
Peer IP. Specify the IP address for the peer to which TCP requests should spill over when the HP EFS WAN Accelerator reaches its built-in capacity limit.
Description. Specify a description to help you identify the peering relationship.
Add Rule. Specify this option to add the rule to the list of rules for the profile.
Remove Selected Rules. To remove an entry, click the check box next to the and entry and click Remove Selected Rules.
Move Rule. Use the Move Rule drop-down list boxes and button to change the order in which rules are evaluated.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You enable Quality of Service (QoS) in the Advanced Networking - QoS Classification page.
You can configure QoS on HP EFS WAN Accelerators to control the prioritization of different types of network traffic and to ensure that HP EFS WAN Accelerators give certain network traffic (for instance, voice over IP) higher priority than other network traffic.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 81
To enable QoS classification
QoS allows you to specify priorities for various classes of traffic and properly distributes excess bandwidth among classes. The HP EFS WAN Accelerator allows you to decouple priority (in terms of delay) from the bandwidth allocation. This provides the flexibility needed to support varying degrees of priority and bandwidth traffic patterns, such as high-priority, low-bandwidth traffic patterns (for example,
Telnet). Many QoS schemes use the term priority to specify how to control the excessive bandwidth among different classes. In the HP EFS WAN Accelerator, priority actually refers to traffic delays and excessive bandwidth is shared, proportional to the minimum bandwidth guaranteed for a specific class.
Enabling this feature is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click QoS Classification to display the Advanced Networking - QoS
Classification page.
82 C ONFIGURING THE HP EFS WAN A CCELERATOR
Figure 2-31. Advanced Networking - QoS Classification Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 83
Control
General
Add New QoS Class
4. Use the controls to complete the configuration, as described in the following table.
Description
Enable QoS Classification. Specify this option to enable QoS.
WAN Bandwidth for Interface XXXX-X. Specify the bandwidth link rate for the WAN interface.
This is the bottleneck WAN bandwidth not the interface speed out of the WAN interface into the router or switch. For example, if your HP EFS WAN Accelerator connects to a router with a 100 Mbps link, do not specify this value—specify the actual WAN bandwidth (for example, T1, T3).
IMPORTANT: Different WAN interfaces can have different WAN bandwidths; this value must be correctly entered for QoS to function correctly.
IMPORTANT: The percentage of excess bandwidth give to a class is relative to the percentage of minimum bandwidth allocated to the class.
Apply. Click Apply to apply your settings to the running configuration.
Class Name. Specify a name for the QoS class.
TIP: You must enable QoS classification and set the bandwidth link rate for the WAN interface to create a QoS class.
Priority. Select a priority type from the drop-down list:
• Real-Time. Specifies real-time traffic class. Traffic that is your highest priority should be given this value.
• Interactive. Specifies an interactive traffic class.
• Business Critical. Specifies the business critical traffic class.
• Normal Priority. Specifies normal priority traffic class.
• Low Priority. Specifies low priority traffic class. Traffic that is your lowest priority should be given this value.
Priorities are listed in decreasing order of importance. These are minimum priority guarantees, if better service is available it is provided. For example, if a class is specified as Low Priority and the higher priority classes are not active, then the Low Priority class is given the highest possible priority for the current traffic conditions.
Guaranteed BW. Specify the bandwidth amount that you want to guarantee for a specific class. All the classes combined cannot exceed 100%. During contention for bandwidth the class is guaranteed for the amount specified, it will receive more bandwidth if there is unused bandwidth remaining.
NOTE: The percentage of excess bandwidth given to a class is relative to the percentage of the minimum bandwidth allocated in the WAN Bandwidth for Interface field.
Add QoS Class. Click Add QoS Class to add a class to the QoS class list.
Remove Selected Classes. To remove an entry, click the check box next to the name and click Remove Selected Classes.
84 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Rule
Modifying a
QoS Class
Description
Insert Rule At. To create a QoS rule for a QoS class, select start, end, or a rule number from the drop-down list. Specify an ordered list of rules.
HP EFS WAN Accelerators evaluate rules in numerical order starting with rule 1. If the conditions set in the rule match, then the rule is applied, and the system moves on to the next packet. If the conditions set in the rule do not match, the system consults the next rule. For example, if the conditions of rule 1 do not match, rule 2 is consulted. If rule 2 matches the conditions, it is applied, and no further rules are consulted.
Class Name. Select a class name from the drop-down list. If the rule matches, the specified rule sends the packet to this class.
Source Subnet. Specify the IP address for the source network. Use the following format:
XXX.XXX.XXX.XXX/XX.
Port. Specify the port for the source subnet. The default value is All.
Destination Subnet. Specify the IP address for the destination network. Use the following format: XXX.XXX.XXX.XXX/XX.
Port. Specify the port for the destination port. The default value is All.
Protocol. Select All, TCP, or UDP from the drop-down list.
Traffic Type. Select an option from the drop-down list:
• Real-Time. Specifies real-time traffic class. Traffic that is your highest priority should be given this value.
• Interactive. Specifies an interactive traffic class.
• Business Critical. Specifies the business critical traffic class.
• Normal Priority. Specifies normal priority traffic class.
• Low Priority. Specifies low priority traffic class. Traffic that is your lowest priority should be given this value.
DSCP. Optionally, specify the DSCP level.
VLAN. Optionally, specify the VLAN tag for the rule.
Add Rule. Click Add Rule to add a rule to the QoS rule list.
Remove Selected Rules. To remove an entry, click the check box next to the name and click Remove Selected Rules.
Move Rule. Select a rule to move and the position where you want to move it to. Click
Move Rule to apply your changes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You can modify a QoS class in the Advanced Networking - QoS Classification <class name> page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 85
To modify a QoS class 1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click QoS Classification to display the Advanced Networking - QoS
Classification page.
4. Click the class name in the Classification List to display the Advanced Networking
- QoS Classification page
Figure 2-32. Advanced Networking - QoS Classification Page
86 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
QoS Class
Setting QoS
Marking
5. Use the controls to complete the configuration, as described in the following table.
Description
Priority. Select a priority type from the drop-down list:
• Real-Time. Specifies real-time traffic class. Traffic that is your highest priority should be given this value.
• Interactive. Specifies an interactive traffic class.
• Business Critical. Specifies the business critical traffic class.
• Normal Priority. Specifies normal priority traffic class.
• Low Priority. Specifies low priority traffic class. Traffic that is your lowest priority should be given this value.
Guaranteed BW. Specify the bandwidth amount that you want to guarantee for a specific class. All the classes combined cannot exceed 100%. During contention for bandwidth the class is guaranteed for the amount specified, it will receive more bandwidth if there is unused bandwidth remaining.
NOTE: The percentage of excess bandwidth given to a class is relative to the percentage of the minimum bandwidth allocated in the WAN Bandwidth for Interface field.
Upper BW. Optionally, specify the upper bandwidth limit. Specifies the maximum amount (percentage) of allowed bandwidth a flow will receive regardless of excess bandwidth available.
6. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
7. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set QoS marking in the Advanced Networking - QoS Marking page.
The QoS feature allows you to enforce a DSCP level for optimized connections. The
DSCP level corresponds to the DiffServ DSCP field in the IP packets header. After you map a source-destination-port pattern and a DSCP level, every packet corresponding to the connection with that destination port has the DSCP field set to that value in the forward and backward direction. On the WAN side of the HP EFS WAN Accelerator, you configure a network router or a traffic shaper to prioritize packets according to the value in the DSCP field before they are sent across the WAN.
After you map a destination port and a DSCP level, every packet corresponding to the connection with that destination port has the DSCP field set to that value in the forward and backward direction. On the WAN side of the HP EFS WAN Accelerator, you configure a network router or a traffic shaper to prioritize packets according to the value in the DSCP field before they are sent across the WAN.
Note that only the first matching mapping will be applied.
Enabling this feature is optional.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 87
To set a QoS marking 1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click QoS Rules to display the Advanced Networking - QoS Marking page.
Figure 2-33. Advanced Networking - QoS Marking Page
88 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Mappings
4. Use the controls to complete the configuration, as described in the following table.
Description
Insert Rule At. Select start, end, or a rule number from the drop-down list. Specify an ordered list of rules where each rule is the DSCP level used on the inner connection for connections matching the source IP subnet, the destination IP subnet and, optionally, the destination port fields.
HP EFS WAN Accelerators evaluate rules in numerical order starting with rule 1. If the conditions set in the rule match, then the rule is applied, and the system moves on to the next packet. If the conditions set in the rule do not match, the system consults the next rule. For example, if the conditions of rule 1 do not match, rule 2 is consulted. If rule 2 matches the conditions, it is applied, and no further rules are consulted.
Source Subnet. Specify the IP address for the source network. Use the following format:
XXX.XXX.XXX.XXX/XX.
Destination Subnet. Specify the IP address for the destination network. Use the following format: XXX.XXX.XXX.XXX/XX.
Port. Specify the port number or port label. A port label is a label that you assign to a set of ports so that you can reduce the number of configuration rules in your system. For
detailed information about how to configure port labels, see “Creating Port Labels” on page 113
.
For the MAPI data channel, specify port 7830 and the corresponding DSCP level.
For the FTP data channel, specify port 20 and the corresponding DSCP level. Setting
QoS for port 20 on the client-side HP EFS WAN Accelerator effects passive FTP, while setting the QoS for port 20 on the server-side HP EFS WAN Accelerator effects port active FTP.
DSCP. Specify the DSCP level (0-63). Specify a DSCP level to use instead of the existing DSCP level. If you do not define a DSCP level, the HP EFS WAN Accelerator uses the existing DSCP level.
IMPORTANT: If your connections already have a DSCP level and you do not define one in the Management Console, the HP EFS WAN Accelerator uses the existing DSCP level for the connection between the HP EFS WAN Accelerators. If you define a DSCP level in the Management Console, the HP EFS WAN Accelerator overrides the existing
DSCP level and the value that you defined is applied.
Description. Specify a description of the QoS rule.
Add Rule. Click Add Rule to add a rule to the QoS rule list.
Remove Selected Rules. To remove an entry, click the check box next to the name and click Remove Selected Rules.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Modifying QoS
Marking
Descriptions
You can modify the description of your QoS marking rules in the Advanced
Networking - QoS Marking Edit page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 89
To modify your QoS rule description
1. Click the Setup tab to expand the Optimization Service menu.
2. Click Advanced Networking expand the Advanced Networking menu.
3. Click Qos Marking to display the Advanced Networking - QoS Marking page.
4. Click Edit Desc in the QoS Rules table to display the Optimization Service - In-
Path Rules Edit page.
Figure 2-34. Advanced Networking - QoS Marking Edit Page
Modifying
Service Ports
5. Modify the description of the QoS rule in the text box and click Update
Description.
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You can modify service port settings in the Advanced Networking - Service Ports page.
Service ports are the ports used for inner connections between HP EFS WAN
Accelerators.
You can configure multiple service ports on the server-side of the network for multiple
QoS mappings. You define a new service port and then map destination ports to that port, so that QoS configuration settings on the router are applied to that service port.
Modifying service port settings is optional.
90 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set a service port 1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click Service Ports to display the Advanced Networking - Service Ports page.
Figure 2-35. Advanced Networking - Service Ports Page
Control
Add Service Port
Add Service Port Mapping
4. Use the controls to complete the configuration, as described in the following table.
Description
Service Port. Specify a port number. The default service ports are 7800 and 7810.
Add Port. Click Add Port to add the port to the service port list.
Set As Default Port. To set a port as the default port, select it and click Set As Default
Port.
Remove Selected Port. To remove an entry, select it and click Remove Selected Port.
Destination Port. Specify a destination port number.
Service Port. Specify a port number.
Add Mapping. Click Add Mapping to add a mapping to the mappings list.
Remove Selected Mappings. To remove an entry, select it and click Remove Selected
Mappings.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 91
Enabling
Simplified
Routing
You can enable simplified routing in the Advanced Networking - Simplified Routing page.
Simplified routing collects the IP address for the next hop Media Access Control
(MAC) address from each packet it receives to use in addressing traffic. Enabling simplified routing eliminates the need to add static routes when the HP EFS WAN
Accelerator is in a different subnet from the client and server.
Without simplified routing if an HP EFS WAN Accelerator is installed in a different subnet from the client or server, you must define one router as the default gateway and static routes for the other routers so that traffic is not redirected back through the HP
EFS WAN Accelerator. In some cases, even with the static routes defined, the Access
Control List (ACL) on the default gateway may still drop traffic that should have gone through the other router.
Simplified routing has the following constraints:
Broadcast support in Proxy File Service configurations cannot be enabled.
WCCP cannot be enabled.
Connection forwarding cannot be enabled if you collect mappings for source
MAC data (that is, the options all or dest-source).
The default route must exist on each HP EFS WAN Accelerator in your network.
Simplified routing requires a client-side and server-side HP EFS WAN
Accelerator.
92 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable simplified routing
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click Simplified Routing to display the Advanced Networking - Simplified
Routing page.
Figure 2-36. Advanced Networking - Simplified Routing Page
Control
Mappings Data Collection Settings
4. Use the controls to complete the configuration, as described in the following table.
Description
Collect Mappings from. Select one of the following options from the drop-down list:
• None. All options are disabled.
• Destination Only. Collects destination MAC data. This option can be used in connection forwarding deployments.
• Destination and Source. Collect mappings from destination and source MAC data.
This option cannot be used in connection forwarding deployments.
• All. Collect mappings for destination and source MAC data and data. It also collects data for connections that are un-natted (that is, connections that are not translated using Network Address Translation (NAT). This option cannot be disabled in connection forwarding deployments.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 93
Enabling WCCP
Groups
You can enable WCCP service groups in the Advanced Networking - WCCP Service
Groups page.
WCCP enables you to redirect traffic that is not in the direct physical path between the client and the server. To enable WCCP, the HP EFS WAN Accelerator must join a service group at the router. A service group is a group of routers and HP EFS WAN
Accelerators which define the traffic to redirect, and the routers and HP EFS WAN
Accelerators the traffic goes through.
Enabling WCCP is optional.
TIP: You can also use the HP EFS WAN Accelerator Command Line Interface (CLI) to configure WCCP service groups. For detailed configuration information (including configuring the WCCP router), see the HP StorageWorks Enterprise File Services WAN Accelerator
Deployment Guide.
NOTE: The following section assumes you are familiar with WCCP. For detailed information about WCCP, see the Cisco documentation Web site at
http://www.cisco.com/univercd/home/home.htm.
94 C ONFIGURING THE HP EFS WAN A CCELERATOR
To enable a WCCP service group
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click WCCP Groups to display the Advanced Networking - WCCP Service
Groups page.
Figure 2-37. Advanced Networking - WCCP Service Groups Page
Control
General
4. Use the controls to complete the configuration, as described in the following table.
Description
Enable WCCP v2 Support. Select this box to enable WCCP v2 support on all groups added to the Service Group list.
Multicast TTL. Specify the TTL boundary for the WCCP protocol packets. The default value is 5.
Apply. Click Apply to apply your settings to the running configuration.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 95
Control
Add New Service Group
Modifying
WCCP Group
Settings
Description
Service Group ID. Specify the service group identification number (from 0 to 255).
The service group ID is the number that is set on the router. A value of 0 specifies the standard http service group.
Router IP. Specify a multicast group IP address or a unicast router IP address. You can specify up to 32 routers. For information on adding additional routers to the group, see
“Modifying WCCP Group Settings” on page 96
.
Password/Confirm Password. Optionally, you can assign a password to the HP EFS
WAN Accelerator. This password must be the same password that is on the router.
WCCP requires that all routers in a service group have the same password. Passwords are limited to 8 characters.
Priority. Specify the WCCP priority for traffic redirection. If a connection matches multiple service groups on a router, the router chooses the service group with the highest priority. The range is 0-255. The default value is 200.
Weight. Determine how often the traffic is redirected to a particular HP EFS WAN
Accelerator. A higher weight redirects more traffic to that HP EFS WAN Accelerator.
The ratio of traffic redirected to an HP EFS WAN Accelerator is equal to its weight divided by the sum of the weights of all the HP EFS WAN Accelerators in the same service group. For example, if there are two HP EFS WAN Accelerators in a service group and one has a weight of 100 and the other has a weight of 200, the one with the weight 100 receives 1/3 of the traffic and the other receives 2/3 of the traffic. The range is 0-65535. The default value corresponds to the number of TCP connections your appliance supports.
NOTE: To enable failover support for WCCP groups, define the service group weight to be 0 on the backup HP EFS WAN Accelerator. If one HP EFS WAN Accelerator has a weight 0, but another one has a non-zero weight, the HP EFS WAN Accelerator with weight 0 does not receive any redirected traffic. If all the HP EFS WAN Accelerators have a weight 0, the traffic is redirected equally among them.
Encapsulation Scheme. Specify the traffic forwarding and redirection scheme: Generic
Routing Encapsulation (gre) or Layer-2 (l2) redirection. Specify either to use Layer-2 first; if Layer-2 is not supported, gre is used.
Add Group. Click Add Group to add the group to the Service Group list.
Remove Selected Groups. To remove an entry, select it and click Remove Selected
Groups.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You modify WCCP service group settings, add additional routers to a service group, and set flags for source and destination ports to redirect traffic (that is, the hash table settings) in the Advanced Networking - WCCP Service Group: <group ID> page.
Before you can modify WCCP service group settings, you must create a WCCP service group. For information on creating a WCCP service group, see
.
For detailed information about hash table settings for WCCP, see the Cisco documentation Web site at http://www.cisco.com/univercd/home/home.htm.
96 C ONFIGURING THE HP EFS WAN A CCELERATOR
To modify WCCP service group settings
1. Click the Setup tab to display the Setup menu.
2. Click Advanced Networking to expand the Advanced Networking menu.
3. Click WCCP Groups to display the WCCP Service Groups page.
4. Click the service group ID in the Groups list to display Advanced Networking -
WCCP Service Group: <Group ID> page.
Figure 2-38. Advanced Networking - WCCP Service Group: <Group ID> Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 97
Control
Group Settings
Flags
Ports
98
5. Use the controls to complete the configuration, as described in the following table.
Description
Password/Confirm Password. Optionally, you can assign a password to the HP EFS
WAN Accelerator. This password must be the same password that is on the router.
WCCP requires that all routers in a service group have the same password. Passwords are limited to 8 characters.
Priority. Specify the WCCP priority for traffic redirection. If a connection matches multiple service groups on a router, the router chooses the service group with the highest priority. The range is 0-255. The default value is 200.
Weight. Determine how often the traffic is redirected to a particular HP EFS WAN
Accelerator. A higher weight redirects more traffic to that HP EFS WAN Accelerator.
The ratio of traffic redirected to an HP EFS WAN Accelerator is equal to its weight divided by the sum of the weights of all the HP EFS WAN Accelerators in the same service group. For example, if there are two HP EFS WAN Accelerators in a service group and one has a weight of 100 and the other has a weight of 200, the one with the weight 100 receives 1/3 of the traffic and the other receives 2/3 of the traffic. The range is 0-65535. The default value corresponds to the number of TCP connections your appliance supports.
NOTE: To enable failover support for WCCP groups, define the service group weight to be 0 on the backup HP EFS WAN Accelerator. If one HP EFS WAN Accelerator has a weight 0, but another one has a non-zero weight, the HP EFS WAN Accelerator with weight 0 does not receive any redirected traffic. If all the HP EFS WAN Accelerators have a weight 0, the traffic is redirected equally among them.
Encapsulation Scheme. Specify the traffic forwarding and redirection scheme: Generic
Routing Encapsulation (gre) or Layer-2 (l2) redirection. Specify either to use Layer-2 first; if Layer-2 is not supported, gre is used.
Update Settings. If you modify group settings, click Update Settings to apply the settings to WCCP groups in the Service Group list.
Source IP Hash. Specify this option to specify that the router hash the source IP address to determine traffic to redirect.
Destination IP Hash. Specify this option to specify that the router hash the destination
IP address to determine traffic to redirect. You can set one or more flags.
Source Port Hash. Specify this option to specify that the router hash the source port to determine traffic to redirect. You can set one or more flags.
Destination Port Hash. Specify this option to specify that the router hash the destination port to determine traffic to redirect. You can set one or more flags.
Update Flags. Click Update Flags to apply your settings.
Ports Disabled. Select this option to turn off port matching.
Use Source Ports. Select this option to redirect TCP traffic when the source port matches the port numbers in the port list.
Use Destination Ports. Select this option to redirect TCP traffic when the destination port matches the port numbers in the Port list.
Apply. Click Apply to apply the change to the Port list.
Add Port. Specify the port number and click Add Port to add it to the Port list. You can add up to 7 ports.
Remove Selected Ports. To remove an entry, select it and click Remove Selected Ports.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Routers
Description
Add Router IP. Specify a multicast group IP address or a unicast router IP address and click Add Router to add it to the Router list. You can add up to 32 routers.
Remove Selected Routers. To remove an entry, select it and click Remove Selected
Routers.
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Enabling PFS
Enabling Proxy File Service
This section describes how to enable and configure the Proxy File Service (PFS) for the HP EFS WAN Accelerator. It includes the following sections:
next
“Adding PFS Shares” on page 102
You can enable and configure PFS support in the Proxy File Service (PFS) -
Configuration page.
NOTE: PFS is not supported on the Model 510.
PFS is an optional integrated virtual file server that allows you to store copies of files on the HP EFS WAN Accelerator with Windows file access, while creating several options for transmitting data between remote offices and centralized locations with improved performance and functions. PFS provides:
LAN access to data residing across the WAN.
Continuous access to files in the event of WAN disruption.
Simplified branch infrastructure and backup architectures.
In v3.0 you no longer need to install the HP EFS Remote Copy Utility (RCU) service on the server to synchronize your PFS shares—all RCU functionality has been moved to the HP EFS WAN Accelerator. When you upgrade from v2.x to v3.x all your existing shares will be running as v2.x shares. If you have legacy shares (that is, shares created with Version v2.x software), you can convert your v2.x shares to v3.x shares in the Management Console.
For detailed information about PFS and when to enable it, see the HP StorageWorks
Enterprise File Services WAN Accelerator Deployment Guide.
Enabling PFS support is optional.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 99
To enable PFS 1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to display the Proxy File Service (PFS) - Configuration page.
Figure 2-39. Proxy File Service (PFS) - Configuration Page
Control
Start Proxy File Service
3. Use the controls to complete the configuration, as described in the following table.
Description
Enable/Disable. Enable or disable PFS support. PFS must be enabled before it is configured. You must restart the HP EFS WAN Accelerator each time PFS is enabled or disabled.
When you click Enable, the page refreshes displaying the Domain/Local Workgroup controls.
Start/Stop. Starts and stops the PFS service.
NOTE: You must restart the HP EFS WAN Accelerator service if you enable PFS support.
100 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Local Workgroup Settings
Domain Settings
Description
Workgroup Name. Specify a local workgroup name. If you configure PFS in
Workgroup mode the HP EFS WAN Accelerator does not need to join a domain.
Workgroup accounts are used by clients when they connect to the HP EFS WAN
Accelerator to access PFS shares.
NOTE: PFS must be enabled and Local Workgroup Settings must be selected before you can set the Workgroup Name. After you have set a Workgroup Name click the Join button.
Join/Leave. Click Join to join the workgroup; click Leave to leave the local workgroup.
IMPORTANT: If you are in Domain mode and have joined a domain you cannot change to workgroup mode until you leave the domain.
User. Specify the login to create a local workgroup account so that users can connect to the HP EFS WAN Accelerator and to access PFS shares.
Password/Password Confirm. Specify and confirm the user account password.
Add. Click Add to add users to the local workgroup.
Remove. To remove an entry, select it and click Remove.
Fully-Qualified Domain Name/Realm. The domain to which you want to make the proxy file server a member. Typically, this is your company domain name. PFS supports
Windows 2000 domains.
NOTE: PFS does not support non-domain accounts other than Administrator accounts.
If you create Local mode shares on a non-administrator account, your security permissions for the share will not be preserved on the origin server.
Primary DNS IP. By default, this field displays the primary DNS IP set in the DNS
Settings page. To modify this entry, click the IP address.
Domain Admin Login. Specify the administrator login for the domain.
Domain Admin Password/Password Confirm. Specify and confirm the domain administrator password.
Domain Controller Name. Optionally, specify the domain controller names (that is, the host that provides user log in service in the domain). Typically, with Windows 2000
Active Directory Service domains, given a domain name, the system automatically retrieves the domain controller name. Enter the names in a comma-separated list.
NOTE: If you specify the domain controller name in high latency situations, it will reduce the time to join domain significantly.
Short Domain Name. Optionally, specify a short domain name, if available. Typically, the short domain name is a sub-string of the realm. In rare situations, this is not the case, and you must explicitly specify it.
Join/Leave. Click Join to join the domain or Leave to leave the domain.
IMPORTANT: If you are in Domain mode and have joined a domain you cannot change to workgroup mode until you leave the domain.
Cancel. Click Cancel to cancel any current domain action that is in progress, such as joining or leaving a domain.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 101
Control
Other PFS Settings
Adding PFS
Shares
Description
Security Signature Settings. Select one of the following settings:
Enabled. This setting supports any type of security signature setting requested by the client machine.
Disabled. This is the default setting. In this setting, PFS does not support clients with security signatures set to Required.
Required. In this setting, PFS supports clients with security signatures set to Enabled or
Required.
Idle Connection Timeout. Specify the number of minutes after which to time-out idle connections. If there is no read or write activity on a mapped PFS share on a client machine, then the TCP connection times out according to the value set and the client has to re-map the share.
Local Admin User Name. Displays the local administrator user name—administrator.
The local administrator account can be used to manage PFS files. You must use the correct syntax for the administrator login name (for example:
administrator@parent_realm) even if you belong to a subdomain.
NOTE: PFS does not support non-domain accounts other than Administrator accounts.
If you create Local mode shares on a non-administrator account, your security permissions for the share will not be preserved on the origin server.
TIP: To change the ACLs on a share hosted by PFS, first map it using the local administrator account.
Local Admin Password/Confirm. Specify and confirm the local administrator password.
Save. Click Save to save your settings permanently.
You create and manage PFS shares in the Proxy File Service - Shares page.
A share is the data volume exported by the origin server.
102 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set PFS share parameters
1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to expand the PFS menu.
3. Click Shares to display the Proxy File Service - Shares page.
4. Click Add a new Proxy Share to display the Proxy File Service (PFS) - Shares page.
Figure 2-40. Proxy File Service - Shares Page
Control
Local Name
Remote Path
Comment
5. Use the controls to complete the configuration, as described in the following table.
Description
Specify the name that you assign to a share on the HP EFS WAN Accelerator. The maximum length is 80 characters.
IMPORTANT: The PFS share and the origin-server share name cannot contain
Unicode characters. The Management Console does not support Unicode characters.
Specify the remote path of the origin file server where the share resides. You must use the Uniform Naming Convention (UNC) for the mapped drive for v3 shares. For example, \\<origin-file-server>\<local-name>
IMPORTANT: The PFS share and the origin-server share name cannot contain
Unicode characters. The Management Console does not support Unicode characters.
NOTE: If you created your share with v2.x software, this value represents the name of the Windows server where the HP EFS Remote Copy Utility (RCU) is running. If the origin server is not the RCU server, you specify the remote path using the UNC format for the mapped drive. If the origin server is the same as the RCU server then you must type its full path including the drive letter, for example C:\data.
Optionally, specify a comment to help you identify the share.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 103
Control
Mode
Version
104
Description
Select one of the following options from the drop-down list:
• Broadcast. The share originates on the origin server and a read-only copy is available as a share on the branch-office HP EFS WAN Accelerator. The data is updated periodically on the HP EFS WAN Accelerator with the data from the origin server.
You specify when and how frequently updates (that is, synchronization) are to occur when you configure a share.
IMPORTANT: While performing a incremental synchronization for Broadcast mode share, if files are deleted on the server, they are not deleted on the HP EFS WAN
Accelerator.
IMPORTANT: For Broadcast mode: if you are performing directory moves regularly
(for example, mv ./dir1/dir2 ./dir3/dir2), incremental synchronization will not reflect these directory changes. You must perform a full synchronization more frequently to keep the PFS shares in synchronization with the remote site.
• Local. After the HP EFS WAN Accelerator receives the initial copy, new data generated by clients is periodically synchronized to the origin server. The folder on the origin server essentially becomes a back-up folder of the share on the HP EFS WAN
Accelerator. Users must not directly write to this folder on the origin server. You specify when and how frequently updates (that is, synchronization) are to occur when you configure a share.
CAUTION: In Local Mode, the HP EFS WAN Accelerator copy of the data is the master copy; do not make changes to the shared files from the origin server while in
Local mode. Changes are propagated from the remote office hosting the share to the origin server.
NOTE: PFS does not support non-domain accounts other than Administrator accounts.
If you create Local mode shares on a non-administrator account, your security permissions for the share will not be preserved on the origin server.
• Stand-Alone. Provides the branch-office HP EFS WAN Accelerator with a one time working copy of data mapped from the origin server. You can specify a remote path to a directory on the origin server, creating a copy at the branch-office. This data is not synchronized back to the origin server. The stand-alone share is an initial and one-time only synchronization.
Select one of the following software versions from the drop-down list. The controls change according to the version you choose. This value represents the version of the share that you want to create.
• Version 2. Specify the server name and remote path for the share folder on the origin file server. With v2 you must have the RCU service running on a Windows server— this can be the origin file server or a separate server.
HP recommends you upgrade your v2.x shares to 3.x shares so that you do not have to
run the RCU on a server. For detailed information, see “Upgrading Shares from V2.x to
IMPORTANT: If you have shares that were created with v2.x of the HP EFS WAN
Accelerator software, the account that starts the RCU must have full permissions to the folder on the origin file server. Also, the log-in user for the RCU server (which is used for v2.x shares) and the share creation user for v3 shares must to be a member of the
Administrators group, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
• Version 3. Specify the login, password, and remote path used to access the share folder on the origin file server. With v3, the RCU runs on the HP EFS WAN
Accelerator—you do not need to install the RCU service on a Windows server.
IMPORTANT: Make sure the users are members of the Administrators group on the remote share server, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control Description
Version 2
Version 3
Server Name. The server located in the data center which hosts the origin data volumes
(folders).
Port. Specify the port for the server.
Account. Specify the fully qualified Windows login (including domain) to be used to access the shares folder on the origin file server. For example,
<Domain>\Administrator.
IMPORTANT: Make sure the users are members of the Administrators group on the remote share server, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
Password/Password Confirm. Specify and confirm the password to be used to access the shares folder on the origin file server.
Incremental Sync Schedule, Date and Time
Specify the date and time that you want updates (synchronization) to start. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator. Subsequent synchronizations are based on the synchronization interval.
IMPORTANT: For Local mode, changes are synchronized from the HP EFS WAN
Accelerator to the origin file server; Broadcast mode changes are synchronized from the origin file server to the HP EFS WAN Accelerator.
IMPORTANT: For Broadcast mode: if you are performing directory moves regularly
(for example, mv ./dir1/dir2 ./dir3/dir2), incremental synchronization will not reflect these directory changes. You must perform a full synchronization more frequently to keep the PFS shares in synchronization with the remote site.
Specify the frequency of updates (synchronization) in minutes.
Incremental Sync Interval
Full Sync Schedule, Date and Time Specify the date and time that you want updates (synchronization) to start. Use full synchronization if performance is not an issue. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS
WAN Accelerator. Subsequent synchronizations are based on the synchronization interval.
IMPORTANT: For Local mode, changes are synchronized from the HP EFS WAN
Accelerator to the file server; Broadcast mode changes are synchronized from the origin file server to the HP EFS WAN Accelerator.
IMPORTANT: For Broadcast mode: if you are performing directory moves regularly
(for example, mv ./dir1/dir2 ./dir3/dir2), incremental synchronization will not reflect these directory changes. You must perform a full synchronization more frequently to keep the PFS shares in synchronization with the remote site.
Full Sync Interval Specify the interval of updates (synchronization) in minutes.
6. Click Save to write your changes to disk or Cancel to cancel your settings.
After you save your share settings the share is added to the Shares list.
NOTE: The PFS service must be started to add a share. To start the PFS service, click Start in
the Proxy File Service (PFS) - Configuration page. For details, see “To enable PFS” on page 100 .
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 105
Enabling and
Synchronizing
Shares
To initialize and enable a share
After you have configured your PFS shares, you must perform the initial synchronization and enable your shares in the Proxy File Services (PFS) - Shares
Details page.
When you perform the initial synchronization of the share, a copy of the data is downloaded from the origin server to the HP EFS WAN Accelerator. The HP EFS
WAN Accelerator also configures the share for automatic synchronization according to the parameters you specified previously.
When you enable sharing for the first time, the share is made available to users for mounting. Users can map the mounted share using standard Windows mapping procedures. For example, map a network drive using the following format:
\\<appliance name or primary interface IP address>\<name of share>
1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to expand the PFS menu.
3. Click Shares to display the Proxy File Service - Shares page.
4. Click the Local Name of the share that you want to initialize or synchronize in the
Shares list to display the Proxy File Service (PFS) - Shares Details page.
Figure 2-41. Proxy File Service (PFS) - Shares Details Page
106 C ONFIGURING THE HP EFS WAN A CCELERATOR
5. Click Syncing Enable to download the initial copy of the share from the origin server to the HP EFS WAN Accelerator and to configure the share for automatic synchronization.
6. Click Sharing Enable to make the share available to end users for mounting. End users will be able to read the share by mapping to the mounted share (for example,
\\HP EFS WAN Accelerator\share1).
After you enable sharing, you can map this share from your machine by typing:
\\<HP EFS WAN Accelerator or primary interface IP address>\<name of share>
7. Click Save to write your changes to disk or Cancel to cancel your settings.
NOTE: When performing the initial synchronization, or when changing large amounts of data, your bandwidth utilization and other graphs may show pockets of inactivity. This is by design.
Upgrading Shares from V2.x to V3.x
When you upgrade to v3.x software, all your existing shares will be running as v2.x shares.
In v3.0 you no longer need to install the HP EFS Remote Copy Utility (RCU) service on the server for synchronization purposes—all RCU functionality has been moved to the HP EFS WAN Accelerator.
If you have legacy shares (that is, shares created with Version 2.x software), you must upgrade your v2.x shares to v3.x shares in the Management Console.
IMPORTANT: HP recommends that you convert your v2.x shares to v3.x shares. HP recommends you do not configure a mixed system of PFS shares, that is v2.x shares and v3.x shares.
When you upgrade your shares you must specify the remote path for the share. The format depends on the path name:
If you created your share with v2.x software, this value represents the name of the
Windows server where the RCU is running. If the remote path share contains a drive letter, then you must provide a new remote path in UNC format that points to the same directory. For example, if the remote path was c:\data\eng on a server called granite. To upgrade, you must log in to granite, and make c:\data\eng a shared directory, with the name eng. In the Management Console, you specify
\\granite\eng as your new remote path for the v3.x upgrade.
If the remote path share is in UNC format, you simply copy that path to the
Remote Path field.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 107
To upgrade your share 1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to expand the PFS menu.
3. Click Shares to display the Proxy File Service - Shares page.
4. In the Shares list click the share name that you want to upgrade. The Proxy File
Service (PFS) - Shares Details page appears.
Figure 2-42. Proxy File Service (PFS) - Shares Details Page
Control
Account
108
5. Click Upgrade to Version 3 on Save. The page refreshes with additional controls necessary to configure v3.
6. Use the controls to complete the configuration, as described in the following table.
Description
Specify the fully qualified Windows login (including domain) to be used to access the shares folder on the origin file server. For example, <Domain>\Administrator.
IMPORTANT: Make sure the users are members of the Administrators group on the remote share server, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Password/Password Confirm
Remote Path
Modifying Share
Settings
Description
Specify and confirm the password to be used to access the shares folder on the origin file server.
Specify the remote path of the origin file server where the share resides. You must use the Uniform Naming Convention (UNC) for the mapped drive for Version 3 shares. For example, \\<origin-file-server>\<local-name>
IMPORTANT: The PFS share and the origin-server share name cannot contain
Unicode characters. The Management Console does not support Unicode characters.
NOTE: If you created your share with v2.x software, this value represents the name of the Windows server where the HP EFS Remote Copy Utility (RCU) is running. If the origin server is not the RCU server, you specify the remote path using the UNC format for the mapped drive. If the origin server is the same as the RCU server then you must type its full path including the drive letter, for example C:\data.
7. Click Save to save your settings permanently or click Cancel to cancel your settings.
You can modify your share settings in the Proxy File Service (PFS) - Shares Details page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 109
To modify share settings
1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to expand the PFS menu.
3. Click Shares to display the Proxy File Service - Shares page.
4. In the Shares list click the share name that you want to modify. The Proxy File
Service (PFS) - Shares page is updated with the share name and current status displayed.
Figure 2-43. Proxy File Service (PFS) - Shares Page
110 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Comment
Mode
Version 2
Version 3
Incremental Sync Schedule, Date and Time
5. Use the controls to modify the configuration, as described in the following table.
Description
Optionally, specify a comment to help you identify the share.
Select one of the following options from the drop-down list:
• Broadcast. The share originates on the origin server and a read-only copy is available as a share on the branch-office HP EFS WAN Accelerator. The data is updated periodically on the HP EFS WAN Accelerator with the data from the origin server.
You specify when and how frequently updates (that is, synchronization) are to occur when you configure a share.
IMPORTANT: For Broadcast mode: if you are performing directory moves regularly
(for example, mv ./dir1/dir2 ./dir3/dir2), incremental synchronization will not reflect these directory changes. You must perform a full synchronization more frequently to keep the PFS shares in synchronization with the remote site.
IMPORTANT: While performing a incremental synchronization for Broadcast mode share, if files are deleted on the server, they are not deleted on the HP EFS WAN
Accelerator.
• Local. After the HP EFS WAN Accelerator receives the initial copy, new data generated by clients is periodically synchronized to the origin server. The folder on the origin server essentially becomes a back-up folder of the share on the HP EFS WAN
Accelerator. Users must not directly write to this folder on the origin server. You specify when and how frequently updates (that is, synchronization) are to occur when you configure a share.
CAUTION: In Local Mode, the HP EFS WAN Accelerator copy of the data is the master copy; do not make changes to the shared files from the origin server while in
Local mode. Changes are propagated from the remote office hosting the share to the origin server.
NOTE: PFS does not support non-domain accounts other than Administrator accounts.
If you create Local mode shares on a non-administrator account, your security permissions for the share will not be preserved on the origin server.
• Stand-Alone. Provides the branch-office HP EFS WAN Accelerator with a one time working copy of data mapped from the origin server. You can specify a remote path to a directory on the origin server, creating a copy at the branch-office. This data is not synchronized back to the origin server. The stand-alone share is an initial and one-time only synchronization.
Port. Specify the port for the server.
Account. Specify the fully qualified Windows login (including domain) to be used to access the shares folder on the origin file server. For example,
<Domain>\Administrator.
IMPORTANT: Make sure the users are members of the Administrators group on the remote share server, either locally on the file server (the local Administrators group) or globally in the domain (the Domain Administrator group).
Password/Password Confirm. Specify and confirm the password to be used to access the shares folder on the origin file server.
Specify the date and time that you want updates (synchronization) to start. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator. Subsequent synchronizations are based on the synchronization interval.
IMPORTANT: For Local mode, changes are synchronized from the HP EFS WAN
Accelerator to the origin file server; Broadcast mode changes are synchronized from the origin file server to the HP EFS WAN Accelerator.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 111
Control Description
Incremental Sync Interval Specify the frequency of updates (synchronization) in minutes.
Full Sync Schedule, Date and Time Specify the date and time that you want updates to start. Use full synchronization if performance is not an issue. The first synchronization, or the initial copy, retrieves data from origin file server and copies it to the local disk on the HP EFS WAN Accelerator.
Subsequent synchronizations are based on the synchronization interval.
IMPORTANT: For Local mode, changes are synchronized from the HP EFS WAN
Accelerator to the file server; Broadcast mode changes are synchronized from the origin file server to the HP EFS WAN Accelerator.
Full Sync Interval Specify the interval of updates (synchronization) in minutes.
6. Click Save to save your settings permanently or click Cancel to cancel your settings.
Performing Manual
Actions on Shares
To perform manual actions on shares
You can verify a share, perform a full synchronization, cancel an operation, or delete a share in the Shares list. The shares list appears on the Proxy File Service (PFS) -
Shares page and the Proxy File Service (PFS) - Shares Details page.
1. Click the Setup tab to display the Setup menu.
2. Click Proxy File Service to expand the PFS menu.
3. Click Shares to display the Proxy File Service - Shares page.
Figure 2-44. Proxy File Service - Shares Page
112 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Actions
4. Select one of the following actions for the share, as described in the following table.
Description
Select one of the following actions from the drop-down list:
• Start Verify. Generates a list of the differences between the share on the HP EFS
WAN Accelerator and the origin file server. The first time you synchronize a share the data comes from the origin file server. A list of differences is available in the PFS
Shares Status report.
• Start Full Sync. Allows you to immediately synchronize the share and its corresponding remote share on the origin file server. You may select Start Full Sync at any time to manually synchronize a share.
• Cancel Action. Cancels the synchronization process.
• Delete Share. Deletes the selected share.
Creating Port
Labels
Port Type
Interactive
RBT-Proto
Secure
Creating Port Labels
This section describes how to create port labels. It includes the following sections:
“Creating Port Labels” on page 113
“Modifying Ports in a Port Label” on page 115
You create port labels in the Port Labels page. Port labels are names given to sets of port numbers. You use port labels to simplify configuration and reporting tasks you perform with the Management Console. For example, you can create port labels to define a set of ports for which the same in-path, load-balancing, or QoS rules apply.
The HP EFS WAN Accelerator automatically discovers all the ports in the system that have traffic. The discovered port along with a label (if one exists) is added to the
Traffic Summary report. If a label does not exist then an unknown label is added to the discovered port.
If you want to change the unknown label to a name representing the port, you must add the port with new label. All statistics for this new port label are preserved from the time the port was discovered.
The following tables summarizes the port labels that are provided by default.
Description and Ports
Automatically passes through traffic on interactive ports (for example, Telnet, TCP ECHO, remote logging, and shell).
Specifies well-known ports used by the system: 7800-7801 (in-path), 7810 (out-of-path),
7820 (failover), 7850 (connection forwarding), 7860 (Interceptor appliance).
Automatically passes through traffic on secure ports (for example, ssh, https, and smtps).
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 113
To create a port label
If you do not want to automatically forward traffic on these ports, you must delete the
Interactive and Secure in-path rules. For detailed information, see
.
For information on common port assignments, see
This feature is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Port Labels to display the Port Labels page.
Figure 2-45. Port Labels Page
Control
Add New Port Label
114
3. Use the controls to complete the configuration, as described in the following table.
Description
Label. Specify the label name. The following rules apply:
• Port labels are not case sensitive and can be any string consisting of letters, the underscore ( _ ), or the hyphen ( - ). There cannot be spaces in port labels.
• The fields in the various rule pages of the Management Console that take a physical port number also take a port label.
• To avoid confusion, do not use a number for a port label.
• Port labels that are used in in-path and other rules, such as QoS, and peering rules cannot be deleted.
• Port label changes (that is, adding and removing ports inside a label) are applied immediately by the rules that use the port labels that you have modified.
Ports. Specify a comma-separated list of port numbers.
Add Label. Click Add Peer to add a neighbor to the peer list.
Remove Selected Labels. To remove an entry, select it and click Remove Selected
Labels.
C ONFIGURING THE HP EFS WAN A CCELERATOR
4. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Modifying Ports in a Port Label
To modify ports in a port label
You can add or delete ports associated with a port label in the Port Label: <Port Label
Name> page.
1. Click the Setup tab to display the Setup menu.
2. Click Port Labels to display the Port Labels page.
3. Click the port label name in the Port Labels list to display the Port Label - <Port
Label Name> page.
Figure 2-46. Port Label: <Port Label Name> Page
4. Under Ports, add or delete ports in the Ports text box.
5. Click Update Ports to save your settings. Click Cancel to cancel your changes.
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Report Parameters
This section describes how to set parameters to generate alarm and error reports. It includes the following sections:
next
“Setting Email Notification” on page 117
“Setting SNMP Parameters” on page 119
“Setting SNMP Trap Receivers” on page 120
“Setting Monitored Ports” on page 121
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 115
Setting Alarm
Parameters
To set alarm parameters
You can set alarms in Reports - Alarm Settings page.
Enabling alarms is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Reports to display the Reports - Alarm Settings page.
Figure 2-47. Reports - Alarm Settings Page
Control
CPU Alarms
Data Store Alarm
116
3. Use the controls to complete the configuration, as described in the following table.
Description
Raise Alarm When CPU Utilization Reaches. Specify this option to trigger an alarm if the average and peak threshold for the Central Processing Unit (CPU) utilization is exceeded. When an alarm reaches the rising threshold, it is activated; when it reaches the lowest or reset threshold, it is reset. After an alarm is triggered, it is not triggered again until it has fallen below the reset threshold.
This alarm is enabled by default, with a rising threshold of 90% and a reset threshold of
70%.
Rising Threshold. Specify rising value CPU utilization.
Reset Threshold. Specify reset value for CPU utilization.
Send email if stale data replaced by fresh data is less than __ day(s) old. Specify this option to trigger an alarm if data in the data store is replaced with new data before the time period specified.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Warning Temperature Alarm
Additional Alarms
Description
Raise Alarm When Temperature (°C) Reaches. Specify this option to trigger an alarm when the CPU temperature exceeds the rising threshold. When the CPU returns to the reset threshold, the rising alarm is cleared. When the CPU returns to the reset threshold, the rising alarm is cleared. The default value for the rising threshold temperature is 70º
C; the default reset threshold temperature is 67º C.
Rising Threshold. Specify the rising temperature (º C).
Reset Threshold. Specify the reset temperature (º C).
Raise Alarm When Network Interface Duplex Errors are Detected. Specify this option to trigger an alarm if the system has encountered a large number of packet errors in your network. Make sure the speed and duplex settings on your HP EFS WAN
Accelerator match the settings on your switch and router.
This alarm is enabled by default.
Raise Alarm When Network Interface Link Errors are Detected. Specify this option to trigger an Simple Network Management Protocol (SNMP) trap, email, and alarm notification when a link goes down. This alarm is disabled by default.
For WAN/LAN interfaces, an alarm is only triggered if in-path support is enabled for that
WAN/LAN pair.
Raise Alarm When Extended Memory Paging Activity is Detected. Specify this option to trigger the memory paging alarm. If 100 pages are swapped every couple of hours, the HP EFS WAN Accelerator is functioning properly. If thousands of pages are swapped every few minutes, contact HP Technical Support.
This alarm is enabled by default.
Raise Alarm If a Software Version Mismatch is Detected in the Network. Specify this option to trigger an alarm if there is a mismatch between software versions in the HP
EFS WAN Accelerator system.
This alarm is enabled by default.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Email
Notification
You can set email notification parameters for events and failures in the
Reports - Notification page.
By default email addresses are not specified for event and failure notification.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 117
To set event and failure email notification
1. Click the Setup tab to display the Setup menu.
2. Click Reports expand the Reports menu.
3. Click Notification to display the Reports - Notification page.
Figure 2-48. Reports - Notification Page
Control
Events
Failures
118
4. Use the controls to complete the configuration, as described in the following table.
Description
Report Events to SNMP Agent. Specify this option to report activity to an SNMP
agent. To complete SNMP settings, see “Setting SNMP Parameters” on page 119 .
For detailed information about SNMP traps sent to configured servers, see
.
Report Events via Email. Specify this option to report events via email.
Email Addresses. Specify a space-separated list of email address to which to send notification messages.
Report Failures via Email. Specify this option to report failures via email.
Email Addresses. Specify a space-separated list of email address to which to send notification messages.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
SMTP Server
Setting SNMP
Parameters
To set SNMP parameters
Description
SMTP Server. Specify a valid Simple Mail Transfer Protocol (SMTP) server. External
DNS and external access for SMTP traffic is required for this feature to function.
IMPORTANT: Make sure you provide a valid SMTP server to ensure that the users you specify receive email notifications for events and failures.
SMTP Port. Specify a port number for the SMTP server.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set SNMP parameters in the Reports - SNMP Settings page.
By default SNMP parameters are not configured.
1. Click the Setup tab to display the Setup menu.
2. Click Reports expand the Reports menu.
3. Click SNMP Settings to display the Reports - SNMP Settings page.
Figure 2-49. Reports - SNMP Settings Page
Control
System Contact
4. Use the controls to complete the configuration, as described in the following table.
Description
Specify the user name for the SNMP contact.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 119
Control
System Location
Read Only Community Name
Description
Specify the physical location of the router.
Specify a string to identify the read-only community. For example: public.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting SNMP
Trap Receivers
To set an SNMP trap
You set SNMP traps in the Reports - SNMP Trap Receivers page.
Traps are messages sent by an SNMP agent that indicate the occurrence of an event.
For detailed information about SNMP traps sent to configured servers, see
.
The default setup does not complete SNMP traps.
1. Click the Setup tab to display the Setup menu.
2. Click Reports expand the Reports menu.
3. Click SNMP Trap Receivers to display the Reports - SNMP Trap Receivers page.
Figure 2-50. Reports - SNMP Trap Receivers Page
120 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New Trap Receiver
4. Use the controls to complete the configuration, as described in the following table.
Description
Receiver IP. Specify the IP address for the SNMP trap. For detailed information about
SNMP traps sent to configured servers, see
Community. Specify the SNMP community name.
Type. Select v1 or v2c from the drop-down list to specify the SNMP software version.
Enabled. Select True to enable or False to disable the trap receiver.
Add Trap Receiver. Click Add Trap Receiver to add the configuration to the Trap
Receiver list.
Remove Selected Receivers. To remove an entry, click the check box next to the entry and click Remove Selected Receivers.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting
Monitored Ports
You set TCP ports you want to monitor in the Reports - Monitored Ports page.
By default, traffic is monitored on ports 21 (FTP), 80 (HTTP), 139 (CIFS:NetBIOS),
445 (CIFS:TCP), 1433 (SQL:TDS), Radius (1812), TACACS+ (49), and 7830
(MAPI).
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 121
To set monitored ports 1. Click the Setup tab to display the Setup menu.
2. Click Reports expand the Reports menu.
3. Click Monitored Ports to display the Reports - Monitored Ports page.
Figure 2-51. Reports - Monitored Ports Page
4. Use the controls to complete the configuration, as described in the following table.
Control
Add New Port to Monitor
Set Maximum Number of Ports to
Monitor
Description
Port. Specify the port to be monitored.
Description. Specify a description for the monitoring activity.
Add Port. Click Add Port to add the port to the Monitored Port list.
Remove Selected Ports. To remove an entry, click the check box next to the entry and click Remove Selected Ports.
Update All Ports. To change the description of a port, edit the description and click
Update All Ports.
Maximum Ports. Specify the maximum number of ports to monitor. This option restricts the number of ports
Set. Click Set to restrict the number of ports that the HP EFS WAN Accelerator monitors.
122 C ONFIGURING THE HP EFS WAN A CCELERATOR
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Logging Options
This section describes how to set local and remote logging for the HP EFS WAN
Accelerator. It includes the following sections:
next
“Setting Remote Logging” on page 124
Setting Local
Logging
To set up local logging
You set up local logging in the Logging - General Settings page.
1. Click the Setup tab to display the Setup menu.
2. Click Logging to display the Logging - General Settings page.
Figure 2-52. Logging - General Settings Page
Control
Log Filtering
Log Rotation
Log Display Preferences
3. Use the controls to complete the configuration, as described in the following table.
Description
Minimum Severity. Select a severity level from the drop-down list. All log messages with this severity level or higher are logged.
Rotate every. From the first drop-down list, select None, Daily, Weekly, or Monthly.
Rotate when log reaches. Specify a file size in MB.
Keep at most __ log file(s). Specify a number to indicate the maximum number of logs to store.
Lines per Page. Specify a number to indicate the lines per page in logs.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 123
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Remote
Logging
To set up remote logging
You set remote logging in the Logging - Remote Log Servers page.
Remote logging forwards HP EFS WAN Accelerator logs to a remote server you specify.
Enabling this feature is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Logging to expand the Logging menu.
3. Click Remote Log Servers to display the Logging - Remote Log Servers page.
Figure 2-53. Logging - Remote Log Servers Page
Control
Add Remote Syslog Server
124
4. Use the controls to complete the configuration, as described in the following table.
Description
Server IP. Specify the IP address for the system log server (syslog).
Minimum Severity. Select a severity level from the drop-down list.
Add Server. Click Add Server to add the remote server to the Remote Syslog Server list.
Remove Selected Servers. To remove an entry, click the check box next to the entry and click Remove Selected Servers.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Setting the Date and Time
This section describes how to set the date and time, and Network Time Protocol (NTP) servers for the HP EFS WAN Accelerator. It includes the following sections:
next
“Setting NTP Servers” on page 126
Setting the Date and Time
To set the date and time
You set the date, time, and time zone in the Date & Time - Set Clock page.
1. Click the Setup tab to display the Setup menu.
2. Click Date & Time to display the Date & Time - Set Clock page.
Figure 2-54. Date & Time - Set Clock Page
Control
Set Time Using NTP Time
Synchronization
Set Time Manually
Time Zone
3. Use the controls to complete the configuration, as described in the following table.
Description
Specify this option to enable NTP time synchronization. NTP synchronization enables the time stamps for logs to match those of other computers that use NTP time synchronization. This option is not required for proper system operation.
Date. Specify the current date. Use the following format: YYYY/MM/DD.
Time. Specify the current time. Use the following format: HH:MM:SS.
Select your time zone from the drop-down list. The default is GMT (Greenwich Mean
Time).
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 125
Setting NTP
Servers
To set an NTP server
NOTE: If you change the time zone, log messages retain the old time zone until you reboot the
HP EFS WAN Accelerator.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set clock synchronization using NTP in the Date & Time - NTP Servers page.
Enabling NTP time synchronization enables the time stamps on the HP EFS WAN
Accelerator logs to match those of other computers using NTP time synchronization.
While this option is not generally required for proper appliance operation, NTP is
required if you use PFS. For detailed information, see “Enabling Proxy File Service” on page 99 .
1. Click the Setup tab to display the Setup menu.
2. Click Date & Time to expand Date & Time menu.
3. Click NTP Servers to display the Date & Time - NTP Servers page.
Figure 2-55. Date & Time - NTP Servers Page
126 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New NTP Server
4. Use the controls to complete the configuration, as described in the following table.
Description
Server IP. Specify the IP address for the NTP server.
Version. Select the NTP protocol version number from the drop-down list.
Enabled. Select True to enable synchronization; select False to disable.
Add Server. Click Add Server to add the NTP server to the list.
Enable/Disable. Enable or disable an NTP server.
Remove Selected Servers. To remove an entry, click the check box next to the entry and click Remove Selected Servers.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting Authentication Methods
This section describes how to set administrator and monitor passwords, Remote
Authentication Dial-In User Service (RADIUS), and Terminal Access Controller
Access Control System (TACACS+) authentication. It includes the following sections:
“Setting General Authentication,” next
“Setting the Administrative Password” on page 129
“Setting the Monitor Password” on page 130
“Setting RADIUS Servers” on page 131
“Setting TACACS+ Servers” on page 133
“Modifying Web Settings” on page 135
“Setting the Message of the Day (MOTD)” on page 136
Setting General
Authentication
You can prioritize local, RADIUS, and TACACS+ authentication methods for the system and set the authorization policy and default user for RADIUS and TACACS+ authorization systems in the Setup: Authentication - General Settings page.
IMPORTANT: Make sure to put the authentication methods in the order in which you want authentication to occur. If authorization fails on the first method, the next method is attempted, and so forth, until all the methods have been attempted.
TIP: To set TACACS+ authorization levels (admin or read-only) to allow certain members of a group to log in, add the following attribute to users on the TACACS+ server:
service = rbt-exec {
local-user-name = "monitor"
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 127
} where you replace monitor with admin for write access.
To set an authentication method
For detailed information about setting up RADIUS and TACACS+ servers, see the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to display the Authentication - General Settings page.
Figure 2-56. Authentication - General Settings Page
Control
Authentication Methods
3. Use the controls to complete the configuration, as described in the following table.
Description
Method 1. Select Local, RADIUS, or TACACS+ from the drop-down list.
NOTE: Make sure you put the authentication methods in the order in which you want them to occur. If authorization fails on the first method, the next method is attempted, and so forth, until all the methods have been attempted.
Method 2. Select None, Local, RADIUS, or TACACS+ from the drop-down list.
Method 3. Select None, Local, RADIUS, or TACACS+ from the drop-down list.
128 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Advanced Authorization
Setting the
Administrative
Password
Description
Authorization Policy. Optionally, select one of the following options from the dropdown list:
• Remote-First. If a local-user mapping attribute is returned and it is a valid local user name, map the authenticated user to the local user specified in the attribute. If the attribute is not present or not valid locally, use the user name specified by the defaultuser command. This is the default behavior.
• Remote-Only. Map only to a remote authenticated user if the authentication server sends a local-user mapping attribute. If the attribute does not specify a valid local user, no further mapping is attempted.
• Local-Only. All remote users are mapped to the user specified. Any vendor attributes received by an authentication server are ignored.
Default User. Optionally, select Admin or Monitor from the drop-down list.
4. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You can change the administrator password Authentication - Account: Admin page.
During the initial setup, you set the administrator password.
The administrator user has full privileges. For example, as an administrator you can set and modify configuration settings, restart the HP EFS WAN Accelerator service, reboot the appliance, and create and view performance and system reports.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 129
To set the administrator password
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click Account: Admin to display the Authentication - Account: Admin page.
Figure 2-57. Authentication - Account: Admin Page
Control
Change Password
Setting the
Monitor
Password
4. Use the controls to complete the configuration, as described in the following table.
Description
New Password. Specify the new administrator password. The password must have a minimum of 6 characters.
Confirm New Password. Retype the new administrator password.
Change Password. Click Change Password to apply your changes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set the monitor user password in the Authentication - Account: Monitor page.
A monitor user can view reports; a monitor user cannot make configuration changes.
130 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set the monitor password
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click Account: Monitor to display the Authentication - Account: Monitor page.
Figure 2-58. Authentication - Account: Monitor Page
Control
Change Password
4. Use the controls to complete the configuration, as described in the following table.
Description
New Password. Specify the new administrator password. The password must have a minimum of 6 characters.
Confirm New Password. Retype the new administrator password.
Change Password. Click Change Password to apply your changes.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting RADIUS
Servers
You set up RADIUS server authentication in the Authentication - RADIUS Servers page.
RADIUS is an access control protocol that uses a challenge and response method for authenticating users. Setting up RADIUS server authentication is optional.
For detailed information about setting up RADIUS and TACACS+ servers, see the HP
StorageWorks Enterprise File Services WAN Accelerator Deployment Guide.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 131
To set RADIUS server authentication
Enabling this feature is optional.
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click RADIUS Servers to display the Authentication - RADIUS Servers page.
Figure 2-59. Authentication - RADIUS Servers Page
Control
General
4. Use controls to complete the configuration, as described in the following table.
Description
Server Key. Specify the server key.
Timeout. Specify the time-out period.
Retries. Specify the number of times you want to allow the user to retry authentication.
Apply. Click Apply to apply your settings to the running configuration.
132 C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New RADIUS Server
Enable/Disable
Remove Selected Servers
Setting
TACACS+
Servers
Description
Server IP. Specify the server IP address.
Authentication Port. Specify the port for the server.
Server Key. Specify the server key.
Timeout. Specify the time-out period.
Retries. Specify the number of times you want to allow the user to retry authentication.
Valid values are 0-5.
Enabled. Select True to enable; select False to disable.
Add Server. Click Add Server to add the RADIUS server to the list.
Enable or disable a RADIUS server.
Remove Selected Servers. To remove an entry, click the check box next to the entry and click Remove Selected Servers.
NOTE: If you add a new server to your network and you do not specify these fields at that time, the global settings are applied automatically.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
You set up TACACS+ server authentication in the Authentication - TACACS+ Servers page.
Enabling this feature is optional.
TACACS+ is an authentication protocol that allows a remote access server to forward a login password for a user to an authentication server to determine whether access is allowed to a given system.
For detailed information about configuring RADIUS and TACACS+ servers to accept login requests from the HP EFS WAN Accelerator, see the HP StorageWorks
Enterprise File Services WAN Accelerator Deployment Guide.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 133
To set a TACACS+ server
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click TACACS+ Servers to display the Authentication - TACACS+ Servers page.
Figure 2-60. Authentication - TACACS+ Servers Page
Control
General
134
4. Use the controls to complete the configuration, as described in the following table.
Description
Server Key. Specify the server key.
Timeout. Specify the time-out period.
Retries. Specify the number of times you want to allow the user to retry authentication.
Update Settings. Click Update Settings to update your global TACACS+ settings.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Control
Add New TACACS+ Server
Enable/Disable
Remove Selected Servers
Description
Server IP. Specify the server IP address.
Authentication Port. Specify the port for the server.
Authentication Type. Select ASCII or PAP from the drop-down list.
Server Key. Specify the server key.
Timeout. Specify the time-out period.
Retries. Specify the number of times you want to allow the user to retry authentication.
Valid values are 0-5.
Enabled. Select True to enable; select False to disable.
Add Server. Click Add Server to add the TACACS+ server to the list.
Enable or disable a TACACS+ server.
Remove Selected Servers. To remove an entry, click the check box next to the entry and click Remove Selected Servers.
NOTE: If you add a new server to your network and you do not specify these fields at that time, the global settings are applied automatically.
5. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Modifying Web
Settings
You can modify Management Console Web user interface settings in the
Authentication: Web Settings page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 135
To modify Web settings
1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click Web Settings to display the Authentication - Web Settings page.
Figure 2-61. Authentication: Web Settings Page
Control
Login Page
Timeout
4. Use the controls to complete the configuration, as described in the following table.
Description
Default Login ID. If desired, modify the user name that appears by default on the authentication page. The default is admin.
Web Activity Time-Out. Specify the number of idle minutes before time-out. Specify 0 to disable time-out.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Setting the
Message of the
Day (MOTD)
You can create or modify a message of the day that appears in the Management
Console or in the CLI in the Authentication - MOTD page.
136 C ONFIGURING THE HP EFS WAN A CCELERATOR
To set a MOTD 1. Click the Setup tab to display the Setup menu.
2. Click Authentication to expand the Authentication menu.
3. Click MOTD in to display the Authentication - MOTD page.
Figure 2-62. Authentication - MOTD Page
4. Type a message in the MOTD (Message of the Day) text box.
5. Click Apply to apply your settings to the running configuration. (Apply your settings to test a new configuration before saving them permanently.)
6. Click Save to save your settings permanently or click Reset to return the settings to their previous values.
Updating Your
Licenses
Managing Licenses
This section describes how to manage HP EFS WAN Accelerator licenses.
You can view a list of active licenses, update expired licenses, and add new license keys in the Licenses page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 137
To update a license 1. Click the Setup tab to display the Setup menu.
2. Click Licenses to display the Licenses page.
Figure 2-63. Licenses Page
Control
Add New License
138
3. Use the controls to complete the configuration, as described in the following table.
Description
Add License. Copy and paste the license key provided by HP into the Add New
License(s) text box, and click Add License to add a license.
TIP: Separate multiple license keys with a space, tab, or
ENTER
.
Remove Selected Licenses. To remove an entry, click the check box next to the entry and click Remove Selected Licenses.
4. Click Save to write the new license to disk or click Reset to return the settings to their previous values.
Viewing Scheduled Jobs
This section describes how to view scheduled jobs.
C ONFIGURING THE HP EFS WAN A CCELERATOR
Viewing
Scheduled Jobs
To view scheduled jobs
You can view completed, pending, inactive jobs, as well as jobs that were not completed because of an error in the Scheduled Jobs page.
Jobs are CLI commands that are scheduled to execute at a time you specify.
The only job you can schedule using the Management Console are software upgrades; for all other jobs, you must use the CLI.
For detailed information about scheduling jobs using the CLI, see the HP
StorageWorks Enterprise File Services WAN Accelerator Command Line-Interface
Reference Manual.
1. Click the Setup tab to display the Setup menu.
2. Click Scheduled Jobs to display the Scheduled Jobs page.
Figure 2-64. Scheduled Jobs Page
3. To remove an entry, click the check box next to the name and click Cancel/
Remove Selected Jobs.
4. Click Save to save your settings permanently or click Reset to return your settings to their previous values.
Managing Configurations
You can save, activate, and import configurations in the Configuration Manager Page.
Each HP EFS WAN Accelerator has an active, running configuration and written, saved configurations.
When you Apply your settings in the Management Console, the values are applied to the active running configuration. but the values are not written to disk and saved permanently.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 139
When you Save your configuration settings, the values are written to disk and saved permanently. They take effect after you restart the HP EFS WAN Accelerator service.
Each time you save your configuration settings, they are written to the current running configuration, and a backup is created. For example, if the running configuration is
myconfig and you save it, myconfig is backed up to myconfig.bak and myconfig is overwritten with the current configuration settings.
The Configuration Manager is a utility that enables you to save configurations as backups or active configuration backups.
The Configuration Manager also includes an Import Configuration utility to support these common use cases:
Replacing an HP EFS WAN Accelerator. If you are swapping one HP EFS
WAN Accelerator for another, you can import all of the network information
(although not the licenses) and disconnect the old HP EFS WAN Accelerator before you switch configurations on the new HP EFS WAN Accelerator.
Configuration template for a large deployment. You can avoid entering the complete HP EFS WAN Accelerator configuration for each of many appliances by setting up a template HP EFS WAN Accelerator and importing template settings to the configuration list.
IMPORTANT: Some configuration settings require you to restart the HP EFS WAN
Accelerator service for the settings to take effect. For detailed information about restarting the
HP EFS WAN Accelerator service, see
“Starting and Stopping Services” on page 144
.
140 C ONFIGURING THE HP EFS WAN A CCELERATOR
To manage configurations
1. Click the Setup tab to display the Setup menu.
2. Click Configuration Manager to display Configuration Manager page.
Figure 2-65. Configuration Manager Page
Control
Current Configuration
3. Use the controls to manage configurations, as described in the following table.
Description
Save Configuration. To save settings that have been applied to the running configuration, click Save Configuration.
Revert. To revert your settings to the running configuration, click Revert.
Save Current Configuration As. To save settings that have been applied to the running configuration as a new file, type a name in the Name text box and click Save As. The configuration name you specify does not become the active configuration.
Activate Selected Configuration. To activate an alternative configuration, click the check box next to the entry and click Activate Selected Configuration.
Remove Selected Configuration. To remove an entry, click the check box next to the entry and click Remove Selected Configuration.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 141
Import Configuration From IP/Host Name. Specify the IP address or host name of the HP EFS WAN Accelerator from which you want to import the configuration.
Remote Admin Password. Specify the administrator password for the remote HP EFS
WAN Accelerator.
Remote Config Name. Specify the name of the configuration you want to import from the remote HP EFS WAN Accelerator.
New Config Name. Specify a new, local, configuration name for this appliance.
Import Shared Data Only. This is enabled by default. Keep this option checked to copy only the following common settings: in-path and out-of-path interface, protocols, CLI and Web, statistics, NTP, SNMP, and alarm settings. The following settings are not automatically copied: failover, SNMP (contact and location), log, and network settings.
Import Configuration. To perform the import configuration operation, click Import
Configuration.
The imported configuration appears in the Configuration list but does not become the active configuration until you click Activate.
TIP: Click the configuration name to display the configuration settings in a new browser window.
IMPORTANT: You must restart the HP EFS WAN Accelerator service for a configuration to
take effect. For detailed information, see “Starting and Stopping Services” on page 144 .
Upgrading Your Software
You can upgrade or revert to a back-up version of the software in the Software Upgrade page.
142 C ONFIGURING THE HP EFS WAN A CCELERATOR
To upgrade or revert software versions
1. Click the Setup tab to display the Setup menu.
2. Click Upgrade Software to display the Software Upgrade page.
Figure 2-66. Software Upgrade Page
Control
Install Upgrade From
Switch to Backup Version
3. Use the controls to complete the configuration, as described in the following table.
Description
URL. Specify this option and type the URL.
If you specify a URL in the URL text box, the image is uploaded, installed, and the HP
EFS WAN Accelerator is rebooted at the time you specify.
Local File. Specify this option and type the path or click Browse to navigate to the local file directory.
If you specify a file to upload in the Local File text box, the image is uploaded immediately, however the image is installed and the HP EFS WAN Accelerator is rebooted at the time you specify.
Install Upgrade. Click Install Image to install the new version of the software.
Schedule Upgrade for Later. Specify this option to schedule the upgrade process.
Specify the date and time for the upgrade:
• Date. Specify the date to run the operation, following the format YYYY/MM/DD.
• Time. Specify the time to run the operation, following the format HH:MM:SS.
To revert to the previous software version (identified on this page), click Switch to
Backup Version. The process starts immediately.
IMPORTANT: You must restart the HP EFS WAN Accelerator service for this configuration
to take effect. For detailed information, see “Starting and Stopping Services” on page 144
.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 143
To start, stop, or restart services
Starting and Stopping Services
You can start, stop, and restart the HP EFS WAN Accelerator service in the Start/Stop
Services page.
The HP EFS WAN Accelerator service is a daemon that execute in the background, performing operations when required.
Many of the HP EFS WAN Accelerator service commands are initiated at startup. It is important to restart the HP EFS WAN Accelerator service when you have made changes to your configuration.
WARNING: Restarting the HP EFS WAN Accelerator service disrupts existing network connections that are proxied through the HP EFS WAN Accelerator.
1. Click the Setup tab to display the Setup menu.
2. Click Start/Stop Services to display the Start/Stop Services page.
Figure 2-67. Start/Stop Services Page
144
3. Under Optimization, to start, stop, or restart the HP EFS WAN Accelerator service, click the appropriate button.
4. Click Save to save your settings permanently or click Reset to return your settings to their previous values.
TIP: To remove data from the data store, click Clean the Data Store. (You rarely need to clean the data store outside of a lab environment.)
C ONFIGURING THE HP EFS WAN A CCELERATOR
To reboot the HP EFS
WAN Accelerator
Rebooting the HP EFS WAN Accelerator
You can reboot the HP EFS WAN Accelerator in the Reboot Appliance page.
Rebooting the HP EFS WAN Accelerator disrupts existing network connections that are currently proxied through the HP EFS WAN Accelerator.
Rebooting can take a few minutes.
1. Click the Setup tab to display the Setup menu.
2. Click Reboot Appliance to display the Reboot Appliance page.
Figure 2-68. Reboot Appliance Page
3. Click Reboot Appliance. After you click Reboot Appliance, you are logged out of the system and it is rebooted
TIP: To remove data from the data store, click the Clean the Data Store on Reboot check box.
(You rarely need to clean the data store outside of a lab environment.)
Shutting Down the HP EFS WAN Accelerator
You can shut down the HP EFS WAN Accelerator in the Shutdown Appliance page.
When you shutdown the HP EFS WAN Accelerator, connections are broken and optimization ceases.
Shutdown can take a few minutes.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 145
To shutdown the HP
EFS WAN Accelerator
To restart the system, you must manually turn on the HP EFS WAN Accelerator.
1. Click the Setup tab to display the Setup menu.
2. Click Shutdown Appliance to display the Shutdown Appliance page.
Figure 2-69. Shutdown Appliance Page
3. Click Shutdown Appliance. After you click Shutdown Appliance, the system is turned off. To restart the system you must manually turn on the HP EFS WAN
Accelerator.
146 C ONFIGURING THE HP EFS WAN A CCELERATOR
CHAPTER 3
Creating HP EFS WAN
Accelerator Reports and Logs
In This Chapter This chapter describes how to create and view performance, network, health, Proxy
File Service (PFS), export, and diagnostic reports. It also describes how to view HP
EFS WAN Accelerator logs, contact technical support, and the online help table of contents. This chapter includes the following sections:
“Creating Performance Reports,” next
“Viewing Networking Reports” on page 165
“Viewing System Health Reports” on page 185
“Viewing Proxy File Service Reports” on page 192
“Exporting Performance Statistics Reports” on page 196
“Viewing System Diagnostic Files” on page 197
“Viewing HP EFS WAN Accelerator Logs” on page 201
Creating Performance Reports
The following section describes how to create and view performance reports. It includes the following sections:
“Creating Bandwidth Optimization Reports,” next
“Creating Data Store Hits Reports” on page 150
“Creating Data Reduction Reports” on page 152
“Creating NFS Statistics Report” on page 155
“Creating Throughput Reports” on page 157
“Creating Traffic Summary Reports” on page 159
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 147
Creating
Bandwidth
Optimization
Reports
The Performance - Bandwidth Optimization report summarizes the overall inbound and outbound bandwidth improvements for your network using the HP EFS WAN
Accelerator. You can create reports according to the time period of your choice, application, and type of traffic.
The Performance - Bandwidth Optimization report includes the following table of statistics that describe bandwidth activity for the time period you specify.
Field
WAN Data
LAN Data
Total Data Reduction % over
Last Week
Description
Specifies the bytes sent over the Wide Area Network (WAN) using the HP EFS WAN
Accelerator.
Specifies the bytes sent over the Local Area Network (LAN) using the HP EFS WAN
Accelerator.
Specifies the total decrease of data transmitted over the WAN, according to the following calculation:
(Data In – Data Out)/(Data In)
Specifies the peak decrease in data transmitted over the WAN.
Peak Data Reduction % over
Last Week
Peak Data Reduction Occurred
At
Capacity Increase
Specifies the time that the peak data reduction occurred.
Specifies the increase in the amount of data transmitted over the WAN, according to the following calculation:
1/(1-Reduction Rate)
What this Report
Tells You
About Report
Graphs
The Performance - Bandwidth Optimization report answers the following questions:
How much bandwidth optimization has occurred?
What was the average and peak amount of data sent?
What was the rate at which data was sent?
What was the overall increase in the amount of data that can be transmitted using the HP EFS WAN Accelerator?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
148 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
To create a Bandwidth
Optimization report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
Figure 3-1. Performance - Bandwidth Optimization Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 149
Control
Period
Application
Traffic
Appliances
Resolution
Refresh
2. Use the controls to customize the report, as described in the following table.
Description
Select Last Minute, Last 5 Minutes, Last Hour, Last Day, Last Week, Last Month, or Custom Interval from the drop-down list.
Select FTP, HTTP, CIFS:NetBIOS, CIFS:TCP, or MAPI from the drop-down list. The default value is All.
Select Bi-directional, WAN-to-LAN, or LAN-to-WAN from the drop-down list.
The default is to include all appliances. To set a custom group, click All and use the dialog box to select an HP EFS WAN Accelerator, a group, or a custom selection of HP
EFS WAN Accelerators to include in the report.
Select High, Medium, or Low from the Resolution drop-down list. High (small bars) allows you to drill down to specific points in time, while Low (large bars) enables you to count or compare aggregate values in the time interval.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15s.
• To refresh your report every 30 seconds, click 30s.
• To turn off refresh, click off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Printer icon
Creating Data
Store Hits
Reports
What This Report
Tells You
150
The Performance - Data Store Hits report summarizes how many times the HP EFS
WAN Accelerator data-store disk and memory have seen a data segment. A hit is a data segment that has been seen before by the data store in the HP EFS WAN Accelerator.
If a hit has occurred, the HP EFS WAN Accelerator sends the reference to the data segment rather than the actual data over the WAN.
The Performance - Data Store Hits report contains the following table of statistics that summarize data store activity.
Field
Total Hits over Last Week
Misses
Description
Specifies the total number of hits against the data store. A hit is a data segment that has been seen before by the data store in the HP EFS WAN Accelerator. If a hit has occurred, the
HP EFS WAN Accelerator sends the reference to the data rather than the actual data over the WAN.
Specifies the number of misses that occurred. A miss is an unmatched data segment—the data store has not seen the data segment before and must send all the data across the
WAN. The data is Lempel-Ziv (LZ) compressed if LZ compression is enabled. For detailed information about
setting optimization policies, see “Setting In-Path Rules” on page 25 .
The Performance - Data Store Hit Rate report answers the following questions:
How much optimization is occurring?
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
About Report
Graphs
How much optimization occurred through disk hits?
How much optimization occurred through memory hits?
How much data traversed the WAN without optimization?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 151
To create the Data
Store Hits report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Performance in the left menu, click Data Store Hit Rate to display the
Performance - Data Store Hits page.
Figure 3-2. Performance - Data Store Hit Rate Page
3. Select Last 5 Minutes, Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
TIP: To refresh your report every 15 seconds, click 15s. To refresh your report every 30 seconds, click 30s.
TIP: To print your report, click the Printer icon in the upper right corner of the page.
Creating Data
Reduction
Reports
152
The Performance - Data Reduction report summarizes the percent reduction of data transmitted by an application such as File Transfer Protocol (FTP), Hypertext Transfer
Protocol (HTTP), NetBIOS and Transmission Control Protocol (TCP), traffic in
Common Internet File Systems (CIFS), and Messaging Application Protocol Interface
(MAPI).
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
The Performance - Data Reduction report includes the following table of statistics that describe data reduction for the application and the time period you specify.
Field
Total Data Reduction %
Over Last Week
Peak Data Reduction % Over
Last Week
Peak Data Reduction
Occured At
Capacity Increase
Description
Specifies the total decrease of data transmitted over the
WAN.
Specifies the peak decrease in data transmitted over the
WAN.
Specifies the time that the peak data reduction occured.
Specifies the increase in the amount of the data that can be transmitted over the WAN.
What This Report
Tells You
About Report
Graphs
The Performance - Data Reduction report answers the following questions:
What was the total reduction in the amount of data that can be transmitted for each application?
What was the peak reduction in the amount of data transmitted for each application?
What was the total capacity increase for the application and time period specified?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 153
To create the Data
Reduction report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Performance in the left menu, click Data Reduction to display the
Performance - Data Reduction page.
Figure 3-3. Performance - Data Reduction Page
154 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Control
Period
Application
Traffic
Resolution
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table.
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select FTP, HTTP, CIFS:NetBIOS, CIFS:TCP, or MAPI from the drop-down list. The default value is All.
Select Bi-directional, WAN-to-LAN, or LAN-to-WAN from the drop-down list.
Select High, Medium, or Low from the Resolution drop-down list. High (small bars) allows you to drill down to specific points in time, while Low (large bars) enables you to count or compare aggregate values in the time interval.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Creating NFS
Statistics
Report
The Performance - NFS Statistics report summarizes NFS optimization statistics for the time period specified.
The Performance - NFS Statistics report contains the following table of statistics that summarize data store activity.
Field Description
Local Response
Remote Response
Reduction % Over Last
Month
Peak Reduction % Over Last
Month
Specifies the local response time for the NFS server.
Specifies the total delay for NFS data.
Specifies the percentage decrease in data transmitted over the WAN.
Specifies the peak-percentage decrease in data transmitted over the WAN.
Peak Reduction Occurred At Specifies the date and time the reduction occurred.
Capacity Increase Specifies the increase in the amount of data that can be transmitted over the WAN.
What This Report
Tells You
About Report
Graphs
The Performance - NFS Statistics report answers the following questions:
What was the local and remote response for NFS data?
How much data was transmitted over the WAN?
What was the overall decrease in data transmitted over the WAN?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 155
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
To create the NFS
Statistics report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Performance in the left menu, click NFS Statistics to display the
Performance - NFS Statistics page.
Figure 3-4. Performance - NFS Statistics Page
156 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Control
Period
Server
Resolution
Refresh
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select the server for which you want to collect statistics from the drop-down list.
Select High, Medium, or Low from the Resolution drop-down list. High (small bars) allows you to drill down to specific points in time, while Low (large bars) enables you to count or compare aggregate values in the time interval.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Printer icon
Creating
Throughput
Reports
The Performance: Throughput report summarizes the throughput or total data transmitted for the application and time period specified.
The Performance - Throughput report includes the following table of statistics that describe data activity for the application and the time period you specify.
Field Description
Average Throughput Over
Last Week
95th Percentile Throughput
Over Last Week
Specifies the average amount of data transmitted.
Specifies the 95th percentile for data activity. The 95th percentile is calculated by taking the peak of the lower 95% of inbound and outbound throughput samples.
Peak Throughput Over Last
Week
Specifies the peak data transmitted in the time period specified.
Peak Throughput Occured At Specifies when the peak data activity occurred.
What This Report
Tells You
About Report
Graphs
The Performance - Throughput report answers the following questions:
What was the average throughput?
What was the peak throughput?
At what time did the peak throughput occur?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 157
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
To create the
Throughput report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Performance in the left menu, click Throughput to display the Performance
- Throughput page
Figure 3-5. .Performance - Throughput Page
158 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Control
Period
Application
Traffic
Resolution
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select FTP, HTTP, CIFS:NetBIOS, CIFS:TCP, or MAPI from the drop-down list. The default value is All.
Select Bi-directional, WAN-to-LAN, or LAN-to-WAN from the drop-down list.
Select High, Medium, or Low from the Resolution drop-down list. High (small bars) allows you to drill down to specific points in time, while Low (large bars) enables you to count or compare aggregate values in the time interval.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Creating Traffic
Summary
Reports
The Performance - Traffic Summary report provides a percentage breakdown of the amount of traffic going through the system by application.
The HP EFS WAN Accelerator automatically discovers all the ports in the system that have traffic. The discovered port along with a label (if one exists) is added to the report.
If a label does not exist then an unknown label is added to the discovered port.
If you want to change the unknown label to a name representing the port, you must add the port with new label. All statistics for this new port label are preserved from the time the port was discovered. For detailed information about adding port labels, see
“Creating Port Labels” on page 113 .
NOTE: The Performance - Traffic Summary report displays a maximum of 16 colors for ports.
If you have more than 16 ports, the colors in the report wrap from the beginning.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 159
The Performance - Traffic Summary report contains the following table of statistics that summarize traffic activity by network protocol.
Field
Total Traffic
FTP (21)
HTTP (80)
CIFS: NetBIOS (139)
CIFS: TCP (445)
MAPI (7830)
Other (Optimized)
Passed Through
(Unoptimized)
Description
Specifies the total amount of traffic transmitted.
Specifies the amount of File Transfer Protocol (FTP) data transmitted. (This also includes FTP data from other ports.)
Specifies the amount of Hypertext Transfer Protocol (HTTP) data transmitted.
Specifies the amount of data transmitted with Network Basic
Input Output System (NETBIOS) over the Common Internet
File System (CIFS) protocol.
Specifies the amount of data transmitted with the CIFS protocol over Transmission Control Protocol (TCP).
Specifies the amount of data transmitted over Mail
Application Programming Interface (MAPI).
Specifies the amount of data transmitted over other applications.
Specifies the amount of traffic transmitted unoptimized.
NOTE: To monitor traffic other than the default traffic listed above, see “Setting Monitored
What This Report
Tells You
About Report
Graphs
The Performance - Traffic Summary report answers the following questions:
How much data reduction occurred with a particular network protocol?
How much data was transmitted optimized?
How much data was transmitted unoptimized?
How much data was transmitted using common network protocols?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
160 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
To create the Traffic
Summary report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Performance in the left menu, click Traffic Summary to display the
Performance - Traffic Summary page.
Figure 3-6. Performance - Traffic Summary Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 161
Control
Period
Type
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select Optimized, Pass-Through, or Both from the drop-down list. The default value is
Optimized.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Viewing Data
Store Reports
162
Viewing Appliance Reports
The following section describes how to create and view appliance reports. It includes the following sections:
next
“Viewing TCP Statistics Report” on page 163
The Appliance - Data Store report summarizes the current status and state of the data store synchronization process.
If you have enabled data store synchronization, it summarizes the state of the
replication process. For detailed information, see “Enabling Failover and Data Store
The Appliance - Data Store report contains the following table that summarizes the current state of the data store in the appliance.
Field
Synchronization Connection
Status
Synchronization Catch-Up
Status
Synchronization Keep-Up
Status
Data Store Percentage Used
(Since Last Clean)
Description
Specifies the current connection status of the data store.
Specifies the process of transferring the newest data in from the active HP EFS WAN Accelerator to the passive HP EFS
WAN Accelerators. The process is complete when the Catch
Up and Keep Up processes meet.
Specifies the process of over-writing the oldest part of the data store and proceeding to the newest part of the data store.
The process is complete when the Catch Up and Keep Up processes meet.
Specifies the percentage of the data store that is available for optimization since the last data store clean request.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
To create the Data
Store report
The Appliance - Data Store report answers the following questions:
Do I have a current connection with my active HP EFS WAN Accelerator?
How much synchronization has occurred on the data store since the synchronization request?
What percentage of the data store is unused?
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Appliance in the left menu, click Data Store to display the Network -
Connected Appliances page.
Figure 3-7. Appliance - Data Store Page
TIP: To print your report, click the Printer icon in the upper right corner of the page.
Viewing TCP
Statistics
Report
The Appliance - TCP Statistics report summarizes TCP statistics for the appliance.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 163
What This Report
Tells You
The Appliance - TCP Statistics report contains the following table of statistics that summarize TCP activity.
Packet Type
Packets Received
Packets Sent
Packets Retransmitted
Timeouts
Loss Events
Description
Specifies the total packets received.
Specifies the total TCP packets sent.
Specifies the total TCP packets retransmitted.
Specifies the number of time-outs.
Specifies the total number of loss events.
The Appliance - TCP Statistics report answers the following questions:
How many TCP packets have been sent and received?
How many TCP packets have been retransmitted?
How many timeouts have occurred?
How many loss events have occurred?
164 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To create the TCP
Statistics report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Appliance in the left menu, click TCP Statistics to display the Network -
TCP Statistics page.
Figure 3-8. Appliance - TCP Statistics Page
TIP: To print your report, click the Printer icon in the upper right corner of the page.
Viewing Networking Reports
The following section describes how to create and view networking reports. It includes the following sections:
“Viewing Connected Appliances Reports,”
next
“Viewing Connection History” on page 167
“Viewing Current Connections” on page 170
“Viewing the Current Connection Details Report” on page 172
“Viewing Connection Pooling” on page 174
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 165
Viewing
Connected
Appliances
Reports
“Viewing Interface Statistics” on page 177
“Creating Link State Reports” on page 178
“Creating Neighbor Statistic Reports” on page 181
“Creating QoS Statistics Reports” on page 182
The Network - Connected Appliances report lists the connected remote HP EFS WAN
Accelerators that are connected to the HP EFS WAN Accelerator.
NOTE: HP EFS WAN Accelerators might remain for a short time in the Network - Connected
Appliances report after they have been shut down or renamed.
What This Report
Tells You
The Network - Connected Appliances report answers the following questions:
What remote HP EFS WAN Accelerators are connected to this HP EFS WAN
Accelerator?
Is there an incompatibility issue between the HP EFS WAN Accelerator software versions.
166 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To create the
Connected Appliances report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Connected Appliances to display the
Network - Connected Appliances page.
Figure 3-9. Network - Connected Appliances Page
Viewing
Connection
History
TIP: Click the appliance name or IP address in the Connected Appliance list to open the
Management Console for the specified system in a new browser window.
TIP: To print your report, click the Printer icon in the upper right corner of the page.
The Network - Connection History report summarizes the current active, established, passed-through, and active-optimized connections. The Network - Connection History report also summarizes half-opened and half-closed connections which can help you assess whether your HP EFS WAN Accelerator is appropriately sized for your network load.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 167
What This Report
Tells You
About Report
Graphs
168
The Network - Connection History report contains the following table of statistics that summarize connection activity.
Packet Type
Optimized Connections
Flowing Connections
Half Opened
Half Closed
Active Optimized
Pass-Through
Description
Specifies the total active connections optimized.
Specifies the total established active connections.
Specifies the total half-opened active connections. A halfopened connection is a TCP connection in which the connection has not been fully established. Half-opened connections count toward the connection count limit on the
HP EFS WAN Accelerator because, at any time, they might become a fully-opened connection.
If you are experiencing a large number of half-opened connections, you might consider a more appropriately sized
HP EFS WAN Accelerator.
Specifies the total half-closed active connections. Halfclosed connections are connections which the HP EFS WAN
Accelerator has intercepted and optimized but are in the process of becoming inactive. These connections are counted toward the connection count limit on the HP EFS
WAN Accelerator. (Half closed connections might remain if the client or server does not close their connections cleanly.)
If you are experiencing a large number of half-closed connections, you might consider a more appropriately sized
HP EFS WAN Accelerator.
Specifies the total number of optimized connections with traffic in the last 60 seconds.
Specifies the total connections passed through, unoptimized, when the connection limit has been reached.
The Network - Connection History report answers the following questions:
How many connections were optimized?
How many connections were passed through, unoptimized?
How many connections were half-opened?
How many connections were half-closed?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
To create the
Connection History report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Connection History to display the Network
- Connection History page.
Figure 3-10. Network - Connection History Page
Control
Period
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 169
Viewing Current
Connections
The Network - Current Connections report displays the connections that are intercepted through the HP EFS WAN Accelerator, including the connections that are passed through unoptimized.
The Network - Current Connections report contains the following Current Connections table of statistics that summarize current connections.
Packet Type
Established
Half Opened
Half Closed
Pass-Through
Forwarded
Description
Specifies the total established active connections.
Specifies the total half-opened active connections. A halfopened connection is a TCP connection in which the connection has not been fully established. Half-opened connections count toward the connection count limit on the
HP EFS WAN Accelerator because at any time they might become a fully opened connection.
If you are experiencing a large number of half-opened connections, you might consider a more appropriately sized
HP EFS WAN Accelerator.
Specifies the total half-closed active connections. Halfclosed connections are connections which the HP EFS WAN
Accelerator has intercepted and optimized but are in the process of becoming inactive. These connections are counted toward the connection count limit on the HP EFS
WAN Accelerator. (Half closed connections might remain if the client or server does not close their connections cleanly.)
If you are experiencing a large number of half-closed connections, you might consider a more appropriately sized
HP EFS WAN Accelerator.
Specifies the total connections passed through, unoptimized when the connection limit has been reached.
Specifies the total number of connections that were forwarded when you have configured a connection forwarding neighbor to manage the connection.
The Network - Current Connections report also contains the following Discarded/
Denied Connections table of statistics that summarize discarded or denied connections.
Packet Type
Discarded
Denied
Description
Specifies the total number of discarded connections.
Discarded packets for the connection that match the Discard rule are dropped silently.
Specifies the total number of denied connections. (When packets for connections match a Deny rule, the appliance actively tries to reset the connection.)
NOTE: If the connection is in an unknown state, the line is greyed-out.
170 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
To create the Current
Connections report
The Network - Current Connections report answers the following questions:
How many connections were established?
How many connections were half-opened?
How many connections were half-closed?
How many connections were denied or discarded?
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Current Connections to display the Network
- Current Connections page.
Figure 3-11. Network - Current Connections Page
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 171
Control
Filter
Type
Printer icon
NOTE: If the connection is in an unknown state, the line is greyed-out.
3. Use the controls to customize the report, as described in the following table..
Description
Specify an IP address or port number in the Filter text box to filter the report.
All. Specifies all established active connections.
• Established (Optimized) Only. Specifies the total established active connections.
• Half-Opened (Optimized) Only. Specifies the total half-opened active connections. A half-opened connection is a TCP connection in which the connection has not been fully established. Half-opened connections count toward the connection count limit on the appliance because at any time they might become a fully opened connection. If you are experiencing a large number of half-opened connections, you might consider a more appropriately sized system.
• Half-Closed (Optimized) Only. Specifies the total half-closed active connections.
Half-closed connections are connections which the appliance has intercepted and optimized but are in the process of becoming inactive. These connections are counted toward the connection count limit on the appliance. (Half closed connections might remain if the client or server does not close their connections cleanly.) If you are experiencing a large number of half-closed connections, you might consider a more appropriately sized system.
• Pass-Through Only. Specifies the total connections passed through, unoptimized when the connection limit has been reached.
• Forwarded. Specifies the total number of connections that were forwarded when you have configured a connection forwarding neighbor to manage the connection.
To print your report, click the Printer icon in the upper right corner of the page.
NOTE: If you have the Secure-CIFS feature enabled (which disables Server Message Block
(SMB) signing), the Network - Current Connections report displays Protocol Error—this is an
expected response. For detailed information about enabling Secure-CIFS, see “Configuring
CIFS Protocol Support” on page 31
.
Viewing the
Current
Connection
Details Report
The Network - Current Connections: Connection Details report displays details about the connected HP EFS WAN Accelerator such as the source and destination IP address, the peer HP EFS WAN Accelerator, the inner local port, and so forth.
172 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
The Network - Current Connections report contains the following table that summarizes current connection details.
Field
Type
Source
Destination
Peer Appliance
Inner Local Port
Outer Local
Outer Remote
Client-Side
Since
App
Bytes In (LAN)
Bytes Out (WAN)
Reduction
Description
Specifies the type of connection.
Specifies the source IP address for the connection.
Specifies the destination IP address for the connection.
Specifies the IP address of the remote HP EFS WAN
Accelerator the connection is going through.
Specifies the local port for the inner connection to the peer
HP EFS WAN Accelerator.
Specifies the local port for the outer connection to the client or server.
Specifies the remote port for the outer connection to the client or server.
Specifies whether the connection is a client-side HP EFS
WAN Accelerator for this connection.
Specifies the time the system has been active.
Specifies the internal protocol blade that is used to service the connection.
Specifies the total number of LAN bytes for this connection.
Specifies the total number of WAN bytes for this connection.
Specifies the percent reduction of traffic over the WAN.
The Network - Current Connections Detail report answers the following questions:
How is the status of this system?
What is the peer for this system?
What are the total number of bytes in and out of this system?
What is the percent reduction of traffic for this system?
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 173
To view current connection details
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Current Connections to display the Network
- Current Connections page.
3. Click the magnifying-glass next to the HP EFS WAN Accelerator name to display the Network - Current Connections Details page.
Figure 3-12. Network - Current Connections Details Page
Viewing
Connection
Pooling
174
TIP: To send keep-alive messages for this system, click Send Keep Alive. To reset keep-alive messages for the system, click Reset.
The Network - Connection Pooling report summarizes the current connection pool of connections to peer appliances.
The Network - Current Connections report contains the following table that summarizes current connection details.
Field
Total Pool
Total Hits
Peak Hits
Peak Hits Occurred At
Description
Specifies the total pool of connections to peer appliances.
Specifies the total number of successful connections.
Specifies the peak number of successful connections in the time period specified.
Specifies the date and time of the peak number of connections.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
About Report
Graphs
The Network - Connection Pooling report answers the following questions:
How large is the pool of connections?
How many connections occurred?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 175
To create the
Connection Pooling report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Connection Pooling to display the Network
- Connection Pooling page.
Figure 3-13. Network - Connection Pooling Page
Control
Period
Type
Resolution
Refresh
Printer icon
176
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select Re-used & Created Connections or Re-used Percentage from the drop down list.
Select High, Medium, Low, or Maximum from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Viewing
Interface
Statistics
The Network - Interfaces Statistics report summarizes the statistics for the primary, inpath LAN and WAN, and auxiliary interfaces. It also displays the IP address, speed, duplex, MAC address, and current status for each interface.
TIP: For auto-negotiated speed and duplex settings the Network - Interfaces Statistics report displays the speed at which they were negotiated.
Primary Interface
In-Path: LAN Interface
In-Path: WAN Interface
Auxiliary Interface
The Network - Interfaces Statistics report displays the following statistics.
Packet Type
RX Packets (Received)
TX Packets (Transmitted)
RX Packets (Received)
TX Packets (Transmitted)
RX Packets (Received)
TX Packets (Transmitted)
RX Packets (Received)
TX Packets (Transmitted)
Description
Specifies the number of packets discarded, errors encountered, packets overrun, and mcast packets sent.
Specifies the number of packets discarded, errors encountered, packets overrun, carriers used, and collisions encountered.
Specifies the number of packets discarded, errors encountered, packets overrun, frames sent, and mcast packets sent.
Specifies the number of packets discarded, errors encountered, packets overrun, carriers used, and collisions encountered.
Specifies the number of packets discarded, errors encountered, packets overrun, frames sent, and mcast packets sent.
Specifies the number packets discarded, errors encountered, packets overrun, carriers used, and collisions encountered.
Specifies the number of packets discarded, errors encountered, packets overrun, and mcast packets sent.
Specifies the number of packets discarded, errors encountered, packets overrun, carriers used, and collisions encountered.
NOTE: If you have multiple dual port or four-port bypass cards installed, the Network -
Interface Statistics report displays the interface statistics for each LAN and WAN port.
What This Report
Tells You
The Network - Interface Statistics report answers the following questions:
How many packets am I transmitting?
How many errors are there in each transmission?
What is the current status of my interface?
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 177
To view Interface
Statistics
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Interface Statistics to display the Network -
Interface Statistics page.
Figure 3-14. Network - Interface Statistics Page
TIP: To print your report, click the Printer icon in the upper right corner of the page.
Creating Link
State Reports
The Network - Link State report summarizes the loss rate for the HP EFS WAN
Accelerator. The loss rate is the rate at which packets are not successfully delivered to the peer HP EFS WAN Accelerator.
178 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
About Report
Graphs
The Network - Link State report answers the following question:
What percentage of packets did not reach the peer HP EFS WAN Accelerator?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 179
To create the Link
State report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Link State to display the Network - Link
State page.
Figure 3-15. Network - Link State Page
Control
Period
Statistic
Peer
Refresh
Printer icon
180
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select Loss Rate from the drop-down list.
Select All or a specific peer from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Creating
Neighbor
Statistic
Reports
The Network - Neighbor Statistics report summarizes number of bytes or packets transferred between the HP EFS WAN Accelerator and a specified neighbor.
What This Report
Tells You
About Report
Graphs
The Network - Neighbor Statistics report answers the following questions:
How many bytes were transferred between an HP EFS WAN Accelerator and a specified neighbor?
How many packets were transferred between an HP EFS WAN Accelerator and a specified neighbor?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 181
To create the Neighbor
Statistics report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click Neighbor Statistics to display the Network
- Neighbor Statistics page.
Figure 3-16. Network - Neighbor Statistics Page
Control
Period
Statistic
Neighbor
Refresh
Printer icon
Creating QoS
Statistics
Reports
182
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select Byte Counts or Packet Counts from the drop-down list.
Select All or a specific neighbor from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
The Network - QoS Statistics report summarizes the number of bytes and packets transmitted for the QoS class or an aggregate of all classes for the time period specified.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
The Network - QoS Statistics report contains the following Data table of statistics that summarize current connections.
Field Description
Data Sent
Data Dropped
Specifies the total amount of data sent over the WAN for the
QoS class.
Specifies the total amount of data packets that were dropped for the QoS class.
Peak Data % Over Last Week Specifies the peak amount of data transmitted over the last week.
Pass Data % Occurred At Specifies when the peak data transmission occurred.
What This Report
Tells You
About Report
Graphs
The Network - QoS Statistics report answers the following questions:
How many bytes transmitted over the WAN for the QoS class?
How many data packets were dropped for the QoS class?
When did the peak data transmission occur for the QoS class?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 183
To create the QoS
Statistics report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Network in the left menu, click QoS Statistics to display the Network - QoS
Statistics page.
Figure 3-17. Network - QoS Statistics Page
Control
Period
Statistic
Class
Refresh
Printer icon
184
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select Byte Counts or Packet Counts from the drop-down list.
Select the QoS class from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Viewing Alarm
Status Reports
Viewing System Health Reports
The following section describes how to view reports that summarize the current status of the HP EFS WAN Accelerator. It includes the following sections:
“Viewing Alarm Status Reports,” next
“Creating CPU Utilization Reports” on page 188
“Creating Memory Paging Reports” on page 190
The Health - Alarm Status report provides status for the HP EFS WAN Accelerator alarms.
The Health -Alarm Status report contains the following table of statistics that summarize traffic activity by application.
Alarm
Admission Control
Asymmetric
Routing
Central Processing
Unit (CPU)
Utilization
Data Store
Licensing
Link State
Description
Whether the system connection limit has been reached. Additional connections are passed through unoptimized. The alarm clears when the HP EFS WAN Accelerator moves out of this condition.
Indicates OK if the system is not experiencing asymmetric traffic. If the system does experience asymmetric traffic, this condition is detected and reported here. In addition, the traffic is passed through, and the route appears in the Asymmetric Routing table. For
information about the Asymmetric Routing table, see “Enabling
Asymmetric Routing Auto-Detection” on page 66 .
Whether the system has reached the CPU threshold for any of the
CPUs in the HP EFS WAN Accelerator. If the system has reached the CPU threshold, check your settings. For detailed information, see
“Setting Alarm Parameters” on page 116 .
If your alarm thresholds are correct, reboot the HP EFS WAN
Accelerator. For detailed information, see “Rebooting the HP EFS
WAN Accelerator” on page 145 .
NOTE: If more than 100 MB of data is moved through an HP EFS
WAN Accelerator, Model 1010 while performing PFS synchronization, the CPU utilization might become high and result in a CPU alarm. This CPU alarm should not be cause for concern.
Whether the data store is corrupt. To clear the data store of data, restart the HP EFS WAN Accelerator service and click Clear Data
Store on Next Restart. For detailed information, see “Starting and
Stopping Services” on page 144
.
Whether your licenses are current. For detailed information about
updating licenses, see “Updating Your Licenses” on page 137 .
Whether the system has detected a link that is down. You are notified via SNMP traps, email, and alarm status.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 185
Alarm
Memory Paging
Network Bypass
NFS V2/V4 Alarm
Optimization
Service
Proxy File Service
Partition Full
Description
Whether the system has reached the memory paging threshold. If
100 pages are swapped approximately every two hours the HP EFS
WAN Accelerator is functioning properly. If thousands of pages are swapped every few minutes, then reboot the HP EFS WAN
Accelerator. For detailed information, see “Rebooting the HP EFS
WAN Accelerator” on page 145 . If rebooting does not solve the
problem, contact HP technical support.
Whether the system is in bypass mode. If the HP EFS WAN
Accelerator is in bypass mode, restart the HP EFS WAN Accelerator service.
If restarting the service does not resolve the problem, reboot the HP
EFS WAN Accelerator. For detailed information, see “Rebooting the
HP EFS WAN Accelerator” on page 145 .
If rebooting does not resolve the problem, shutdown and restart the
Stopping Services” on page 144
.
Whether the system has triggered a v2 or v4 NFS alarm.
Whether the system has detected a software error in the HP EFS
WAN Accelerator service. The HP EFS WAN Accelerator service continues to function, but an error message appears in the logs that you should investigate. For detailed information, see
EFS WAN Accelerator Logs” on page 201 .
Whether you Proxy File Service (PFS) partition is full.
186 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
What This Report
Tells You
Alarm
Proxy File Service
Connection Error
Proxy File Service
Operation Failed
Redundant Array of
Independent Disks
(RAID)
Software Version
Mismatch
System Disk Full
Temperature
Description
Whether there has been a PFS connection error. If a connection error is detected, restart the HP EFS WAN Accelerator service and PFS.
For detailed information, see
“Enabling Proxy File Service” on page 99 and
“Starting and Stopping Services” on page 144
.
Whether a synchronization operation has failed. If an operation failure is detected, attempt the operation again. For detailed information, see
“Adding PFS Shares” on page 102
.
Whether the system has encountered RAID errors (for example, missing drives, pulled drives, drive failures, and drive rebuilds).
For drive rebuilds, if a drive is removed and then reinserted, the alarm continues to be triggered until the rebuild is complete.
IMPORTANT: Rebuilding a disk drive can take 4-6 hours.
NOTE: RAID status applies only to the HP EFS WAN Accelerator,
Series 3000 and 5000.
Whether there is a mismatch between software versions in your network. If a software mismatch is detected, resolve the mismatch by upgrading or reverting to a previous version of the software. For detailed information, see
“Upgrading Your Software” on page 142
.
NOTE: If a software version mismatch occurs and you are running v.1.2 and client-side v.2.1 HP EFS WAN Accelerators, you must set the correct version of the HP EFS WAN Accelerator service protocol on the client-side v.2.1 appliances using the HP EFS WAN
Accelerator CLI: sh> peer <addr> version min 5 sh> peer <addr> version max 5
Whether the data store has reached maximum disk capacity.
Whether the CPU temperature has exceeded the critical threshold.
The default value for the rising threshold temperature is 70º C; the default reset threshold temperature is 67º C.
The Health -Alarm Status report answers the following question:
What is the current status of the HP EFS WAN Accelerator?
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 187
To create the Alarm
Status report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Health in the left menu, click Alarm Status to display the Health - Alarm
Status page.
Figure 3-18. Health - Alarm Status Page
NOTE: To print your report, click the Printer icon in the upper right corner of the page.
Creating CPU
Utilization
Reports
What this Report
Tells You
The Health - CPU Utilization report summarizes the percentage of the CPU utilized in the time period specified.
About Report
Graphs
188
The Health - CPU Utilization report answers the following questions:
How much CPU is being used?
What is the average and peak percentage of CPU being used?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To create the CPU
Utilization report
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Health in the left menu, click CPU Utilization to display the Health - CPU
Utilization page.
Figure 3-19. Health - CPU Utilization Page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 189
Control
Period
Refresh
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
Printer icon
Creating
Memory Paging
Reports
The Health - Memory Paging report provides the total number of memory pages, per second, utilized in the time period specified.
The Health - Memory Paging report includes the following table of statistics that describe memory paging activity for the time period you specify.
Field Description
Total Pages Swapped Out Specifies the total number of pages swapped. If 100 pages are swapped approximately every two hours the HP EFS
WAN Accelerator is functioning properly. If thousands of pages are swapped every few minutes, contact HP technical support.
Average Pages Swapped Out Specifies the average number of pages swapped. If 100 pages are swapped every couple of hours the HP EFS WAN
Accelerator is functioning properly. If thousands of pages are swapped every few minutes, contact
HP technical support.
Peak Pages Swapped Out
Peak Pages Swapped Out
Occured At
Specifies the peak number of pages swapped.
Specifies the time and date that the peak number of pages were swapped.
What this Report
Tells You
About Report
Graphs
The Health - Memory Paging report answers the following questions:
How much memory is being used?
What is the average and peak amount of memory pages swapped?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
190 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To create Memory
Paging report
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Health in the left menu, click Memory Paging to display the Health -
Memory Paging page.
Figure 3-20. Health - Memory Paging Page
Control
Period
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table.
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 191
Viewing Proxy File Service Reports
The following section describes the Proxy File Share (PFS) Status report. It includes the following sections:
“Viewing PFS Share Status Reports,”
next
“Viewing PFS Statistics” on page 193
The PFS Share Status report provides information about your PFS shares: the size of the share and the status of the share. For detailed information, see
.
Viewing PFS
Share Status
Reports
What this Report
Tells You
The PFS Share Status report answers the following questions:
What action is occurring on the share?
How large is the share?
Is the share ready for synchronization?
Is a synchronization currently occurring?
192 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To view the PFS Share
Status report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Click Share Status in the left menu to display the PFS - Share Status page.
Figure 3-21. PFS - Share Status Page
Viewing PFS
Statistics
TIP: Click the local name to display the PFS - Shares page.
The PFS Statistics report summarizes PFS connection statistics for the time period specified.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 193
The PFS Statistics report contains the following table of statistics that summarize PFS activity.
Packet Type Description
Bytes Received
Peak Bytes Received Over
Last Month
Peak Bytes Occurred At
Specifies the total bytes received on the specified share.
Specifies the peak number of bytes received over the last month on the specified share.
Specifies the date and time for the peak activity for the share.
Bytes Sent
Peak Bytes Sent Over Last
Month
Specifies the total bytes sent for the specified share.
Specifies the peak number of bytes sent over the last month on the specified share.
Peak Bytes Sent Occurred At Specifies the date and time for the peak bytes sent for the share.
What this Report
Tells You
About Report
Graphs
The PFS Statistics report answers the following questions:
How many bytes were sent and received for the specified share?
How many bytes were sent and received over the last month for the specified share?
What is the date and time for the peak activity (both, sent and received)?
In bar-graph and line-graph reports, the x-axis (or tick mark) plots time, according to the interval you select. The y-axis plots the metric of interest, such as gigabytes (GB) of bandwidth, percent (%) of data reduction, connection counts, and the like.
A diamond icon above the top margin of the graph points to the value on the x-axis (the time) at which the peak occurred.
A diamond icon outside the right margin of the graph points to the value on the y-axis
(for example, the percent) that is the average value for the time period selected.
Pie chart graphs do not indicate peaks or averages. Pie chart graphs represent the aggregate for the time period selected.
About Report Data The HP EFS WAN Accelerator system polls bandwidth and connection metrics every second and can report on performance for periods as long as one year. However, due to performance and disk space considerations, data representation in reports for periods longer than the Last 5 Minutes are interpolated from aggregate data points.
194 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To view the PFS Share:
Name-of-Share report
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Click Statistics in the left menu to display the PFS Statistics page.
Figure 3-22. PFS Statistics Page
Control
Period
Share
Resolution
Refresh
Printer icon
3. Use the controls to customize the report, as described in the following table..
Description
Select Last Hour, Last Day, Last Week, or Last Month from the drop-down list.
Select All or a specific share from the drop-down list.
Select High, Medium, or Low from the Resolution drop-down list. High (small bars) allows you to drill down to specific points in time, while Low (large bars) enables you to count or compare aggregate values in the time interval.
Set a rate to refresh the report display:
• To refresh your report every 15 seconds, click 15 Seconds.
• To refresh your report every 30 seconds, click 30 Seconds.
• To turn off refresh, click Off.
NOTE: The refresh rate does not affect polling. Polling occurs every 5 minutes.
To print your report, click the Printer icon in the upper right corner of the page.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 195
Exporting
Performance
Statistics
To export statistics
Exporting Performance Statistics Reports
The following section describes how to export performance statistics reports.
You can export performance statistics in comma-separated value (CSV) format in the
Export - Statistics report. The CSV format allows you to easily import the statistics into spreadsheets and databases. You can open the CSV file in any text editor.
The CSV file contains commented lines (comments beginning with the # character) at the beginning of the file. These comments report what host generated the file, the report that was generated, time boundaries, the time the export occurred, and the version of the HP EFS WAN Accelerator the file was exported from. The statistical values are provided in columns: the first column is the date and time of the statistic sample, the columns that follow contain the data.
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Export in the left menu, click Statistics to display the Export - Statistics page.
Figure 3-23. Export - Statistics Page
196 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Control
Report
After
Before
Export
Printer icon
3. Use the controls to customize the report, as described in the following table..
Description
Select the report you want to export from the drop-down list.
Specify a date and time from which the statistics should begin in the After text box. Use the following format: YYYY/MM/DD HH:MM:SS.
Specify a date and time from which the statistics should begin in the After text box. Use the following format: YYYY/MM/DD HH:MM:SS
Click Export to export your data.
To print your report, click the Printer icon in the upper right corner of the page.
Viewing System Diagnostic Files
The following section describes how to view HP EFS WAN Accelerator system files to help diagnose problems. It includes the following sections:
next
“Viewing System Snapshots” on page 198
“Viewing TCP Dump Files” on page 199
Viewing System
Dump Files
The Diagnostic - System Dump Report displays a list of system dump files and their size. A system dump contains a copy of the kernel data on the system. System dump files can help you diagnose problems in the HP EFS WAN Accelerator.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 197
To view system dump files
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Diagnostic in the left menu, click System Dumps to display the Diagnostic
- System Dumps page.
Figure 3-24. Diagnostic - System Dumps Page
3. Click the file name to open a file save dialog box to download the file.
4. Click Generate System Dump Now to generate a new system dump.
TIP: To remove an entry, click the check box next to the name and click Remove Selected
Files. This action applies the settings to the running configuration. Click Save to write your settings to memory or click Reset to return the settings to their previous values.
Viewing System
Snapshots
The Diagnostic -System Snapshots report displays a list of system snapshot files and their size. A system snapshot is a saved copy of memory including the contents of all memory, bytes, hardware registers, and status indicators. It is periodically taken to restore the system in the event of failure. System snapshot files can help you diagnose problems in the HP EFS WAN Accelerator.
198 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
To view system snapshot files
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Diagnostic in the left menu, click System Snapshots to display the
Diagnostic - System Snapshots page.
Figure 3-25. Diagnostic - System Snapshots Page
3. Click the file name to open a file save dialog box to download the file.
TIP: To remove an entry, click the check box next to the name and click Remove Selected
Files.
Viewing TCP
Dump Files
The Diagnostic -TCP Dumps report displays a list of system snapshot files and their size. TCP dump files contain summary information for every Internet packet received or transmitted on the interface. TCP dump files can help you diagnose problems in the
HP EFS WAN Accelerator.
To view TCP data you must run the tcpdump tool using the HP EFS WAN Accelerator
CLI. For detailed information, see the HP StorageWorks Enterprise File Services WAN
Accelerator Command Line Interface Reference Manual.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 199
To view TCP dump files
1. Click the Reports tab to display the Performance - Bandwidth Optimization page.
2. Under Diagnostic in the left menu, click TCP Dump to display the Diagnostic -
TCP Dump page.
Figure 3-26. Diagnostic - TCP Dump Page
200
3. Click the file name to open a file save dialog box to download the file.
TIP: To remove an entry, click the check box next to the name and click Remove Selected
Files.
Viewing HP EFS WAN Accelerator Logs
The following section describes how to view HP EFS WAN Accelerator logs.
C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
Viewing HP EFS
WAN
Accelerator
Logs
To view HP EFS WAN
Accelerator logs
You can view HP EFS WAN Accelerator logs in the Logging: System Log report. Use system logs to monitor HP EFS WAN Accelerator activity and to troubleshoot problems with the system. The most recent log events are listed first.
1. Click the Logging tab to display the Logging: System Log page.
Figure 3-27. Logging: Current Log Page
Control
Filter
Prev
Page #
Jump to Page
Launch Continuous Log
Rotate Logs Now
Disk Icon
2. Use the controls to customize your logs, as described in the following table.
Description
Specify a keyword or string and click Filter to display logs according to the parameters you specify.
Click Prev to view previous pages in the log.
Click the page number to view additional pages in the log.
Specify a page number and click Go to view the log page you specified.
Click Launch Continuous Log to display continuous log messages in your Web browser. (This feature might not be supported in all Web browsers.)
Click Rotate Logs Now to archive the current log.
Click the Disk icon in the upper right corner to download the log file to your local machine.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 201
Contacting
Technical
Support
Getting Help
The following section describes how to obtain help with your HP EFS WAN
Accelerator. It includes the following sections:
“Contacting Technical Support,”
next
“Viewing Online Help Contents” on page 202
You can obtain the technical support phone number from the Help: Technical Support page.
TIP: Under Website, click the Web site link to go to the HP technical support Web site.
Viewing Online
Help Contents
To view online help contents
You can view the table of contents for online help in the Help: Online Help page. The online help contains page-level help for each page in the Management Console.
1. Click the Help tab to display the Help: Technical Support page.
2. Click Online Help in the left menu to display the Help: Online Help page.
3. Click the Click here for online help link to display the online help table of contents.
202 C REATING HP EFS WAN A CCELERATOR R EPORTS AND L OGS
APPENDIX A
HP EFS WAN Accelerator Ports
In This Appendix This appendix describes the HP EFS WAN Accelerator default and supported secure ports. It includes the following sections:
“Commonly Optimized Ports” on page 204
“Commonly Excluded Ports” on page 204
“Interactive Ports Forwarded by the HP EFS WAN Accelerator” on page 205
“Secure Ports Forwarded by the HP EFS WAN Accelerator” on page 206
Default Ports
The following table summarizes HP EFS WAN Accelerator default ports with the port label: RBT-Proto.
Default Ports
7744
7800
7801
7810
7820
7830
7840
7850
7860
Description
Data store synchronization port.
In-path port for appliance to appliance connections.
Network Address Translation (NAT) port.
Out-of-path server port.
Failover port for redundant appliances.
Messaging Application Programming Interface (MAPI)
Exchange 2003 port.
Name Service Provider Interface (NSPI) port.
Connection forwarding (neighbor) port.
Interceptor appliance
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 203
204
IMPORTANT: For two HP EFS WAN Accelerators to optimize traffic, ports 7800 and 7810, must be passed through firewall devices located between the pair of HP EFS WAN Accelerators.
Also, SYN and SYN/ACK packets with the TCP option 76 must be passed through firewalls for autodiscovery to function properly. For the HP EFS WAN Accelerator Manager, port 22 must be passed through the firewall for it to function properly.
Commonly Optimized Ports
The HP EFS WAN Accelerator by default optimizes all ports. If you do not want the
HP EFS WAN Accelerator to optimize all ports for an in-path or out-of path configuration, you can specify specific ports for optimization.
Although these ports can vary according to your requirements, the following ports are commonly optimized and monitored for in-path and out-of-path configurations:
21 (FTP)
49 (TACACS+)
80 (HTTP)
139 (CIFS:NETBIOS)
445 (CIFS:TCP)
1433 (SQL:TDS)
1812 (Radius)
7830 (MAPI)
Commonly Excluded Ports
This section summarizes the ports that are commonly excluded from optimization in the HP EFS WAN Accelerator.
If you have multiple ports that you want to exclude, create a port label and list the ports.
Application
PolyComm
(video conferencing)
Cisco IPTel
Ports
1503, 1720-1727, 3230-3253, 5060
2000
HP EFS WAN A CCELERATOR P ORTS
Interactive Ports Forwarded by the HP EFS
WAN Accelerator
A default in-path rule with the port label Interactive is automatically created in your system. This in-path rule automatically passes through traffic on interactive ports (for example, Telnet, TCP ECHO, remote logging, and shell).
TIP: If you do not want to automatically forward these ports, simply delete the Interactive rule in the Management Console.
The following table lists the interactive ports that are automatically forwarded by the
HP EFS WAN Accelerator.
Port Description
2727
3389
5060
5631
1718-1720
2000-2003
2427
2598
5900-5903
6000
179
513
514
1494
7
23
37
107
TCP ECHO
Telnet
UDP/Time
Remote Telnet Service
Border Gateway Protocol
Remote Login
Shell
Citrix h323gatedisc
Cisco SCCp
Media Gateway Control Protocol Gateway
Citrix
Media Gateway Control Protocol Call Agent
MS WBT Server, TS/Remote Desktop
SIP
PC Anywhere
VNC
X11
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 205
206
Secure Ports Forwarded by the HP EFS WAN
Accelerator
A default in-path rule with the port label Secure is automatically created in your system. This in-path rule automatically passes through traffic on commonly secure ports (for example, ssh, https, and smtps).
TIP: If you do not want to automatically forward these ports, simply delete the Secure rule in the Management Console.
The following table lists the common secure ports that are automatically forwarded by the HP EFS WAN Accelerator.
Type ftps-data ftps telnets imaps pop3s l2tp pptp tftps ssh tacacs https smtps nntps imap4-ssl sshell ldaps
Port
989/tcp
990/tcp
992/tcp
993/tcp
995/tcp
1701/tcp
1723/tcp
3713/tcp
22/tcp
49/tcp
443/tcp
465/tcp
563/tcp
585/tcp
614/tcp
636/tcp
Description
SSH Remote Login Protocol
TACACS+ http protocol over TLS/SSL
# SMTP over SSL (TLS) nntp protocol over TLS/SSL (was snntp)
IMAP4+SSL (use 993 instead)
SSLshell ldap protocol over TLS/SSL (was sldap) ftp protocol, data, over TLS/SSL ftp protocol, control, over TLS/SSL telnet protocol over TLS/SSL imap4 protocol over TLS/SSL pop3 protocol over TLS/SSL (was spop3) l2tp pptp
TFTP over TLS
HP EFS WAN A CCELERATOR P ORTS
The following table contains the uncommon ports automatically forwarded by the HP
EFS WAN Accelerator.
Type csvr-sslproxy xnm-ssl msft-gc-ssl networklenss xtrms jt400-ssl seclayer-tls vt-ssl jboss-iiop-ssl ibm-diradm-ssl can-nds-ssl can-ferret-ssl linktest-s asap-tcp-tls topflow-ssl sdo-tls nsiiops ddm-ssl corba-iiop-ssl ieee-mms-ssl ircs njenet-ssl ssm-cssps ssm-els giop-ssl ttc-ssl syncserverssl dicom-tls realsecure orbix-loc-ssl orbix-cfg-ssl cops-tls
Port
3529/tcp
3539/tcp
3660/tcp
3661/tcp
3747/tcp
3864/tcp
3885/tcp
3896/tcp
3191/tcp
3220/tcp
3269/tcp
3410/tcp
3424/tcp
3471/tcp
3496/tcp
3509/tcp
2482/tcp
2484/tcp
2679/tcp
2762/tcp
2998/tcp
3077/tcp
3078/tcp
3183/tcp
261/tcp
448/tcp
684/tcp
695/tcp
994/tcp
2252/tcp
2478/tcp
2479/tcp
Description
IIOP Name Service over TLS/SSL
DDM-Remote DB Access Using Secure Sockets
CORBA IIOP SSL
IEEE-MMS-SSL irc protocol over TLS/SSL
NJENET using SSL
SecurSight Authentication Server (SSL)
SecurSight Event Logging Server (SSL)
Oracle GIOP SSL
Oracle TTC SSL
Sync Server SSL
DICOM TLS
Real Secure
Orbix 2000 Locator SSL
Orbix 2000 Locator SSL
COPS/TLS
ConServR SSL Proxy
XML NM over SSL
Microsoft Global Catalog with LDAP/SSL
NetworkLens SSL Event xTrade over TLS/SSL jt400-ssl securitylayer over tls
Virtual Token SSL Port
JBoss IIOP/SSL
IBM Directory Server SSL
Candle Directory Services using SSL
Candle Directory Services using SSL
LXPRO.COM LinkTest SSL asap/tls tcp port
TopFlow SSL
Simple Distributed Objects over TLS
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 207
Type sdo-ssh iss-mgmt-ssl suucp wsm-server-ssl sip-tls imqtunnels davsrcs intrepid-ssl rets-ssl
Port
3897/tcp
3995/tcp
4031/tcp
5007/tcp
5061/tcp
7674/tcp
9802/tcp
11751/tcp
12109/tcp
Description
Simple Distributed Objects over SSH
ISS Management Svcs SSL
UUCP over SSL wsm server ssl
SIP-TLS iMQ SSL tunnel
WebDAV Source TLS/SSL
Intrepid SSL
RETS over SSL
208 HP EFS WAN A CCELERATOR P ORTS
APPENDIX B
HP EFS WAN Accelerator MIB
In This Appendix This appendix describes the HP EFS WAN Accelerator Enterprise Simple Network
Management Protocol (SNMP) Message Information Base (MIB). It includes the following sections:
“Accessing the HP EFS WAN Accelerator Enterprise MIB,”
next
“HP EFS WAN Accelerator Enterprise MIB” on page 211
Accessing the HP EFS WAN Accelerator
Enterprise MIB
The HP EFS WAN Accelerator Enterprise MIB monitors device status, peers, and provides network statistics for seamless integration into network management systems such as Hewlett Packard OpenView Network Node Manager, Paessler Router Traffic
Grapher (PRTG), and other SNMP browser tools.
For detailed information about configuring and using these network monitoring tools, consult their individual web sites.
The following guidelines describe how to download and access the HP EFS WAN
Accelerator Enterprise MIB using common MIB browsing utilities.
You can download the HP EFS WAN Accelerator Enterprise MIB (RBT-mib.txt) from the HP support site at http://www.hp.com and load it into any MIB browser utility.
Some utilities might expect a file type other than a text file. If this occurs, change the file type to the one expected.
Some utilities assume that the root is mib-2 by default. If the utility sees a new node, such as enterprises, it might look under mib-2.enterprises. If this occurs, use .iso.org.dod.internet.private.enterprises.rbt as the root.
Some command-line browsers might not load all MIB files by default. If this occurs, find the appropriate command option to load the RBT-mib.txt file. For example, for NET-SNMP browsers: snmwalk -m all
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 209
210
SNMP Traps
The following table summarizes the Simple Network Management Protocol (SNMP) traps sent out from the HP EFS WAN Accelerator to configured trap receivers.
Trap procCrash
(enterprises.17163.1.1.4.1) procExit
(enterprises.17163.1.1.4.2) cpuUtil
(enterprises.17163.1.1.4.3) pagingActivity
(enterprises.17163.1.1.4.4) smartError
(enterprises.17163.1.1.4.5) peerVersionMismatch
(enterprises.17163.1.1.4.6) bypassMode
(enterprises.17163.1.1.4.7) raidError
(enterprises.17163.1.1.4.8) storeCorruption
(enterprises.17163.1.1.4.9)
Description
A process has crashed and subsequently been restarted by the system. A system snapshot associated with this crash has been created on the HP EFS WAN Accelerator and is accessible via the CLI or Management Console. HP
Technical Support may need this information to determine the cause of the crash.
A process has unexpectedly exited and been restarted by the system. The process may have exited on its own or due to other process failures on the HP EFS WAN Accelerator.
Please contact HP Technical Support to determine the cause of this event.
Average CPU utilization has exceeded an acceptable threshold. If CPU utilization spikes are frequent, it may be because the system is undersized. Sustained CPU load may be symptomatic of more serious issues; please contact HP
Technical Support for more information.
The system is running low on memory and has begun swapping memory pages to disk. This event can be triggered during a software upgrade on an optimizing HP EFS WAN
Accelerator and is normal. Should this event be triggered at any other time, please contact HP Technical Support.
A disk is about to fail. Contact HP Technical Support immediately.
NOTE: Applicable to models 510, 520, 1010, 1020, 2010,
2020 only.
The HP EFS WAN Accelerator has encountered another HP
EFS WAN Accelerator which is running an incompatible version of system software. The CLI, Management Console, or the SNMP peer table can be referenced to determine which HP EFS WAN Accelerator is causing the conflict. To resolve the problem: upgrade your system software.
The HP EFS WAN Accelerator has entered bypass mode and is now passing through all traffic unoptimized. This event can be the result of a system crash or a manual configuration change, such as a service restart or system reboot.
A drive has failed in a RAID array. Consult the CLI or
Management Console to determine the location of the failed drive. Please contact HP Technical Support for assistance with installing the spare drive. The appliance will continue to optimize during this event.
NOTE: Applicable to models 3010 and 5010 only.
Corruption has been detected in the data store. Please contact HP Technical Support immediately
B - HP EFS WAN A CCELERATOR MIB
Trap admissionMemError
(enterprises.17163.1.1.4.10) admissionConnError
(enterprises.17163.1.1.4.11) haltError
(enterprises.17163.1.1.4.12) serviceError
(enterprises.17163.1.1.4.13) scheduledJobError
(enterprises.17163.1.1.4.14) confModeEnter
(enterprises.17163.1.1.4.15) confModeExit
(enterprises.17163.1.1.4.16)
Description
The HP EFS WAN Accelerator is optimizing traffic beyond its rated capability. During this event, the HP EFS WAN
Accelerator will continue to optimize existing connections, but new connections will be passed through without optimization.
The HP EFS WAN Accelerator is optimizing a number of connections beyond its rated capability. During this event, theHP EFS WAN Accelerator will continue to optimize existing connections, but new connections will be passed through without optimization.
The optimization service has halted due to a serious software error. Please contact HP Technical Support immediately.
The optimization service has encountered a condition which may degrade optimization performance. Please consult the system log for more information.
A scheduled job on the system (e.g., a software upgrade) has failed. Please use the CLI or the Management Console to determine which job failed.
A user on the system has entered configuration mode from either the CLI or Management Console.
A user on the system has entered configuration mode from either the CLI or Management Console.
HP EFS WAN Accelerator Enterprise MIB
The following text is an example of the HP EFS WAN Accelerator Enterprise MIB file
(RBT-mib.txt).
STEELHEAD-MIB DEFINITIONS ::= BEGIN
IMPORTS
OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, enterprises,
Unsigned32,
TimeTicks, IpAddress, Counter64 FROM SNMPv2-SMI
DateAndTime FROM SNMPv2-TC
products FROM RBT-MIB; steelhead MODULE-IDENTITY
LAST-UPDATED "200608040000Z"
ORGANIZATION "Riverbed Technology, Inc."
CONTACT-INFO
" Balaji Ramachandran
DESCRIPTION "Steelhead MIB"
::= { products 1 } system OBJECT IDENTIFIER
::= { steelhead 1 } status OBJECT IDENTIFIER
::= { steelhead 2 }
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 211
212 config OBJECT IDENTIFIER
::= { steelhead 3 } alarms OBJECT IDENTIFIER
::= { steelhead 4 } statistics OBJECT IDENTIFIER
::= { steelhead 5 }
--
--
-- SYSTEM
--
-model OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Appliance model"
::= { system 1 } serialNumber OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Appliance serial number"
::= { system 2 } systemVersion OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"System software version string"
::= { system 3 }
--
--
-- STATUS
--
-systemClock OBJECT-TYPE
SYNTAX DateAndTime
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"System clock time"
::= { status 1 } health OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current health"
::= { status 2 } serviceStatus OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
B - HP EFS WAN A CCELERATOR MIB
STATUS current
DESCRIPTION
"Current service status"
::= { status 3 } serviceUptime OBJECT-TYPE
SYNTAX TimeTicks
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current service uptime"
::= { status 4 } procTable OBJECT-TYPE
SYNTAX SEQUENCE OF ProcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of managed processes"
::= { status 5 } procEntry OBJECT-TYPE
SYNTAX ProcEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry for one process"
INDEX { procIndex }
::= { procTable 1 }
ProcEntry ::=
SEQUENCE {
procIndex Unsigned32,
procName OCTET STRING,
procStatus OCTET STRING,
procNumFailures Unsigned32
} procIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Synthetic numeric unique ID of process"
::= { procEntry 1 } procName OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Unique name of process"
::= { procEntry 2 } procStatus OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current state of process"
::= { procEntry 3 } procNumFailures OBJECT-TYPE
SYNTAX Unsigned32
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 213
214
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Number of times process has crashed or exited unexpectedly"
::= { procEntry 4 } peerStatus OBJECT IDENTIFIER
::= { status 6 } peerTable OBJECT-TYPE
SYNTAX SEQUENCE OF PeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of peers"
::= { peerStatus 1 } peerEntry OBJECT-TYPE
SYNTAX PeerEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry for one peer"
INDEX { peerIndex }
::= { peerTable 1 }
PeerEntry ::=
SEQUENCE {
peerIndex Unsigned32,
peerHostname OCTET STRING,
peerVersion OCTET STRING, peerAddress IpAddress,
peerModel OCTET STRING
} peerIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index of peer"
::= { peerEntry 1 } peerHostname OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Hostname of peer"
::= { peerEntry 2 } peerVersion OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"System software version of peer"
::= { peerEntry 3 } peerAddress OBJECT-TYPE
SYNTAX IpAddress
MAX-ACCESS read-only
STATUS current
DESCRIPTION
B - HP EFS WAN A CCELERATOR MIB
"IP address of peer"
::= { peerEntry 4 } peerModel OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Model of peer"
::= { peerEntry 5 }
--
--
-- CONFIG
--
-activeConfig OBJECT-TYPE
SYNTAX OCTET STRING
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current active configuration"
::= { config 1 } inpath OBJECT IDENTIFIER
::= { config 2 } inpathSupport OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"In-path support"
::= { inpath 1 } outofpath OBJECT IDENTIFIER
::= { config 3 } outofpathSupport OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Out-of-path support"
::= { outofpath 1 }
--
--
-- ALARMS
--
-alarmsPrefix OBJECT IDENTIFIER
::= { alarms 0 } procCrash NOTIFICATION-TYPE
OBJECTS { procName }
STATUS current
DESCRIPTION
"A procCrash trap signifies that a process managed by PM
has crashed and left a core file. The variable sent with
the notification indicates which process crashed."
::= { alarmsPrefix 1 }
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 215
216 procExit NOTIFICATION-TYPE
OBJECTS { procName }
STATUS current
DESCRIPTION
"A procExit trap signifies that a process managed by PM
has exited unexpectedly, but not left a core file.
The variable sent with the notification indicates
which process exited."
::= { alarmsPrefix 2 } cpuUtil NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"The average CPU utilization in the past minute has gone
above the acceptable threshold"
::= { alarmsPrefix 3 } pagingActivity NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"The system has been paging excessively (thrashing)"
::= { alarmsPrefix 4 } smartError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"SMART has sent an event about a possible disk error"
::= { alarmsPrefix 5 } peerVersionMismatch NOTIFICATION-TYPE
OBJECTS { systemVersion }
STATUS current
DESCRIPTION
"Detected a peer with a mismatched software version"
::= { alarmsPrefix 6 } bypassMode NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"The appliance has entered bypass (failthru) mode"
::= { alarmsPrefix 7 } raidError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"An error has been generated by the RAID array"
::= { alarmsPrefix 8 } storeCorruption NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"The data store is corrupted"
::= { alarmsPrefix 9 } admissionMemError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"Admission control memory alarm has been triggered"
::= { alarmsPrefix 10 } admissionConnError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
B - HP EFS WAN A CCELERATOR MIB
"Admission control connections alarm has been triggered"
::= { alarmsPrefix 11 } haltError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"The service is halted due to a software error"
::= { alarmsPrefix 12 } serviceError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"There has been a service error. Please consult the log file"
::= { alarmsPrefix 13 } scheduledJobError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A scheduled job has failed during execution"
::= { alarmsPrefix 14 } confModeEnter NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A user has entered configuration mode"
::= { alarmsPrefix 15 } confModeExit NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A user has exited configuration mode"
::= { alarmsPrefix 16 } linkError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"An interface has lost link on the appliance"
::= { alarmsPrefix 17 } nfsV2V4 NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"NFS v2/v4 alarm notification"
::= { alarmsPrefix 18 } powerSupplyError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A power supply on the appliance has failed. Not supported on all models"
::= { alarmsPrefix 19 } asymRouteError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"Asymmetric routes have been detected,certain connections might not have been optimized because of this."
::= { alarmsPrefix 20 } fanError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 217
218
"A fan error has been detected on the appliance. Not supported on all models"
::= { alarmsPrefix 21 } memoryError NOTIFICATION-TYPE
STATUS current
DESCRIPTION
"A memory error has been detected on the appliance. Not supported on all models"
::= { alarmsPrefix 22 }
--
--
-- STATISTICS
--
-cpuLoad OBJECT IDENTIFIER
::= { statistics 1 } cpuLoad1 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"One-minute CPU load in hundreths"
::= { cpuLoad 1 } cpuLoad5 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Five-minute CPU load in hundreths"
::= { cpuLoad 2 } cpuLoad15 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Fifteen-minute CPU load in hundreths"
::= { cpuLoad 3 } cpuUtil1 OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Percentage CPU utilization, aggregated across all CPUs, rolling average over the past minute"
::= { cpuLoad 4 } cpuIndivUtilTable OBJECT-TYPE
SYNTAX SEQUENCE OF CPUIndivUtilEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Details about the individual CPU utilization"
::= { cpuLoad 5 } cpuIndivUtilEntry OBJECT-TYPE
SYNTAX CPUIndivUtilEntry
MAX-ACCESS not-accessible
B - HP EFS WAN A CCELERATOR MIB
STATUS current
DESCRIPTION
"Entry for one cpu"
INDEX { cpuIndivId }
::= {cpuIndivUtilTable 1 }
CPUIndivUtilEntry ::=
SEQUENCE {
cpuIndivIndex Unsigned32,
cpuIndivId Unsigned32,
cpuIndivIdleTime Unsigned32,
cpuIndivSystemTime Unsigned32,
cpuIndivUserTime Unsigned32
} cpuIndivIndex OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the table"
::= { cpuIndivUtilEntry 1 } cpuIndivId OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the table"
::= { cpuIndivUtilEntry 2 } cpuIndivIdleTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Idle time for this CPU"
::= { cpuIndivUtilEntry 3 } cpuIndivSystemTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"System time for this CPU"
::= { cpuIndivUtilEntry 4 } cpuIndivUserTime OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"User time for this CPU"
::= { cpuIndivUtilEntry 5 } connectionCounts OBJECT IDENTIFIER
::= { statistics 2 } optimizedConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current total number of optimized connections"
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 219
220
::= { connectionCounts 1 } passthroughConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current total number of pass-through connections"
::= { connectionCounts 2 } halfOpenedConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current total number of half-opened (optimized) connections"
::= { connectionCounts 3 } halfClosedConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current total number of half-closed (optimized) connections"
::= { connectionCounts 4 } establishedConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current number of established (optimized) connections"
::= { connectionCounts 5 } activeConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Current number of active (optimized) connections"
::= { connectionCounts 6 } totalConnections OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of connections"
::= { connectionCounts 7 } bandwidth OBJECT IDENTIFIER
::= { statistics 3 } bandwidthAggregate OBJECT IDENTIFIER
::= { bandwidth 1 } bwAggInLan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total bytes WanToLan LAN side since last restart of service"
::= { bandwidthAggregate 1 }
B - HP EFS WAN A CCELERATOR MIB
bwAggInWan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total bytes WanToLan WAN side since last restart of service"
::= { bandwidthAggregate 2 } bwAggOutLan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total bytes LanToWan LAN side since last restart of service"
::= { bandwidthAggregate 3 } bwAggOutWan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total bytes LanToWan WAN side since last restart of service"
::= { bandwidthAggregate 4 } bandwidthPerPort OBJECT IDENTIFIER
::= { bandwidth 2 } bwPortTable OBJECT-TYPE
SYNTAX SEQUENCE OF BWPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"List of bandwidth ports"
::= { bandwidthPerPort 1 } bwPortEntry OBJECT-TYPE
SYNTAX BWPortEntry
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Entry for one port"
INDEX { bwPort }
::= { bwPortTable 1 }
BWPortEntry ::=
SEQUENCE {
bwPort Unsigned32,
bwPortInLan Counter32,
bwPortInWan Counter32,
bwPortOutLan Counter32,
bwPortOutWan Counter32,
bwPortNumber Unsigned32
} bwPort OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS not-accessible
STATUS current
DESCRIPTION
"Index for the table"
::= { bwPortEntry 1 } bwPortInLan OBJECT-TYPE
SYNTAX Counter32
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 221
222
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bytes WanToLan LAN side since last restart of service"
::= { bwPortEntry 2 } bwPortInWan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bytes WanToLan WAN side since last restart of service"
::= { bwPortEntry 3 } bwPortOutLan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bytes LanToWan LAN side since last restart of service"
::= { bwPortEntry 4 } bwPortOutWan OBJECT-TYPE
SYNTAX Counter32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Bytes LanToWan WAN side since last restart of service"
::= { bwPortEntry 5 } bwPortNumber OBJECT-TYPE
SYNTAX Unsigned32
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Port Number"
::= { bwPortEntry 6 } bandwidthPassThrough OBJECT IDENTIFIER
::= { bandwidth 3 } bwPassThroughIn OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Amount of incoming pass through traffic"
::= { bandwidthPassThrough 1 } bwPassThroughOut OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Amount of outgoing pass through traffic"
::= { bandwidthPassThrough 2 } bwPassThroughTotal OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total passthrough traffic"
::= { bandwidthPassThrough 3 }
B - HP EFS WAN A CCELERATOR MIB
datastore OBJECT IDENTIFIER
::= { statistics 4 } hitsTotal OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of datastore hits since last restart of service"
::= { datastore 1 } missTotal OBJECT-TYPE
SYNTAX Counter64
MAX-ACCESS read-only
STATUS current
DESCRIPTION
"Total number of datastore misses since last restart of service"
::= { datastore 2 }
END
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 223
224 B - HP EFS WAN A CCELERATOR MIB
Glossary
ARP. Address Resolution Protocol. An IP protocol used to obtain a node's physical address.
Bandwidth. The upper limit on the amount of data, typically in kilobits per second
(kbps), that can pass through a network connection. Greater bandwidth indicates faster data transfer capability.
Bit. A Binary digit. The smallest unit of information handled by a computer; either 1 or 0 in the binary number system.
Blade. One component in a system that is designed to accept some number of components (blades).
Bottleneck. Anode in a network at which information is processed more slowly, or any element (for example, a network interface card) that slows network connectivity rates
CIFS. Common Internet File System. CIFS is the remote file system access protocol used by Windows servers and clients to share files across the network.
Database Cursor. A record pointer in a database. When a database file is selected and the cursor is opened, the cursor points to the first record in the file. Using various commands, the cursor can be moved forward, backward, to top of file, bottom of file and so forth.
Default gateway. The default address of a network or Web site. It provides a single domain name and point of entry to the network or site.
DHCP. Dynamic Host Configuration Protocol. Software that automatically assigns IP addresses to client stations logging onto a TCP/IP network.
Domain. In the Internet, a portion of the Domain Name Service (DNS) that refers to groupings of networks based on the type of organization or geography.
DNS. Domain Name Service. System used in the Internet for translating names of network nodes into IP addresses. A Domain Name Server notifies hosts of other host
IP addresses, associating host names with IP addresses.
Ethernet. The most widely used Local Area Network (LAN) access method.
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 225
226
FDDI. Fiber Distributed Data Interface. A set of American National Standards
Institute (ANSI) protocols for sending digital data over fiber optic cable. FDDI networks are token-passing networks, and support data rates of up to 100 Mbps (100 million bits) per second. FDDI networks are typically used as backbones for Wide-
Area Networks (WANs).
Filer. An appliance that attaches to a computer network and is used for data storage.
Gateway. A computer that acts as an intermediate device for two or more networks that use the same protocols. The gateway functions as an entry and exit point to the network. Transport protocol conversion might not be required, but some form of processing is typically performed.
Gigabit Ethernet. An Ethernet technology that raises transmission speed to 1 Gbps
(1000 Mbps).
Hashing. Producing hash values for accessing data or for security. A hash value, is a number generated from a string of text. The hash is substantially smaller than the text itself and it is generated by a formula in such a way that it is extremely unlikely that some other text will produce the same hash value.
Heartbeat. A repeating signal transmitted from one appliance to another that indicates that the appliance is operating.
Heuristic. A method of problem solving using exploration and trial and error methods.
Heuristic program design provides a framework for solving the problem in contrast with a fixed set of rules (algorithmic) that cannot vary.
Host. A computer or other computing device that resides on a network.
Host address. The IP address assigned to each computer attached to the network.
Host name. Name given to a computer, usually by DNS.
HSRP. Hot Standby Routing Protocol. HSRP is a routing protocol from Cisco that provides backup to a router in the event of failure. Using HSRP, several routers are connected to the same segment of an Ethernet, FDDI or token-ring network and work together to present the appearance of a single virtual router on the LAN. The routers share the same IP and MAC addresses, therefore in the event of failure of one router, the hosts on the LAN are able to continue forwarding packets to a consistent IP and
MAC address. The process of transferring the routing responsibilities from one device to another is transparent to the user.
HTTP. Hypertext Transport Protocol. The protocol used by Web browsers to communicate with Web servers.
HTTPS. Hypertext Transport Protocol Secure. The protocol for accessing a secure
Web server. Using HTTPS directs the message to a secure port number to be managed by a security protocol.
Interface. The point at which a connection is made between two elements, systems, or devices so that they can communicate with one another.
G LOSSARY
Internet. The collection of networks tied together to provide a global network that use the TCP/IP suite of protocols.
IP. Internet protocol. Network layer protocol in the TCP/IP stack that enables a connectionless internetwork service.
IP address. In IP version 4 (IPv4), a 32-bit address assigned to hosts using the IP protocol. Also called an Internet address.
IPsec. Internet Protocol Security Protocol. A set of protocols to support secure exchange of packets at the IP layer. IPsec has been deployed widely to implement
Virtual Private Networks (VPNs). IPsec supports two encryption modes: Transport and
Tunnel. For IPsec to work, the sending and receiving devices must share a public key.
Latency. Delay between a request being issued and its response being received.
Layer-4. A communications protocol (called the transport layer) responsible for establishing a connection and ensuring that all data has arrived safely. The application delivers its data to the communications system by passing a stream of data Bytes to the transport layer along with the socket (the IP address of the station and a port number) of the destination machine.
MAPI. Messaging API. A programming interface from Microsoft that enables a client application to send and receive mail from Exchange Server or a Microsoft Mail (MS
Mail) messaging system. Microsoft applications such as Outlook, the Exchange client, and Microsoft Schedule use MAPI.
Microsoft Exchange. Messaging and groupware software for Windows from
Microsoft. The Exchange server is an Internet-compliant messaging system that runs under Windows systems and can be accessed by Web browsers, the Windows In-box,
Exchange client, or Outlook. The Exchange server is also a storage system that can hold anything that needs to be shared.
Netmask. A 32-bit mask which shows how an Internet address is divided into network, subnet, and host parts. The netmask has ones in the bit positions in the 32-bit address which are used for the network and subnet parts, and zeros for the host part.
The mask must contain at least the standard network portion (as determined by the class of the address), and the subnet field should be contiguous with the network portion.
Neural Network. A modeling technique based on the observed behavior of biological neurons and used to mimic the performance of a system. It consists of a set of elements that start out connected in a random pattern, and, based upon operational feedback, are molded into the pattern required to generate the required results. It is used in applications such as robotics, diagnosing, forecasting, image processing and pattern recognition.
NFS. Network File System. The file sharing protocol in a UNIX network.
NIS. Network Information Services. A naming service that allows resources to be easily added, deleted or relocated.
OSPF. Open Shortest Path First. An interior gateway routing protocol developed for
IP networks based on the shortest path first or link-state algorithm. Routers use link-
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 227
228 state algorithms to send routing information to all nodes in an internetwork by calculating the shortest path to each node based on a topography of the Internet constructed by each node. Each router sends that portion of the routing table (keeps track of routes to particular network destinations) that describes the state of its own links. It also sends the complete routing structure (topography).
Packet. A unit of information transmitted, as a whole, from one device to another on a network.
Probe. A small utility program that is used to investigate, or test, the status of a system, network or Web site.
Policy. Routing and Quality of Service (QoS) scheme that forwards data packets to network interfaces based on user-configured parameters.
Port. A pathway into and out of the computer or a network device such as a hub, switch, or router. On network devices, the ports are for communications, typically connecting Ethernet cables or other network devices.
Router. A device that forwards data packets from one LAN or WAN to another. Based on routing tables and routing protocols, routers read the network address in each transmitted frame and make a decision on how to send it based on the most expedient route (traffic load, line costs, speed, bad lines, etc.). Routers work at Layer-3 in the protocol stack, whereas bridges and switches work at the Layer-2.
SMB. Server Message Block. A message format used by DOS and Windows to share files, directories and devices. There are also a number of products that use SMB to enable file sharing among different operating system platforms. A product called
Samba, for example, enables UNIX and Windows machines to share directories and files.
SNMP. Simple Network Management Protocol. A network protocol that provides a way to monitor network devices, performance, and security and to manage configurations and collect statistics.
Switch. A network device that filters and forwards frames based on the destination address of each frame. The switch operates at Layer-2 (data link layer) of the Open
System Interconnection (OSI) model.
Tcl. Tool Command Language. A scripting language for developing cross-platform applications. Tcl is an interpreted language that runs on Windows, UNIX, and
Macintosh operating systems. An associated add-on toolkit, Tk (Toolkit) allows you to easily create graphical applications.
TCP. Transmission Control Protocol. The error correcting Transport layer (Layer-4) in the TCP/IP protocol suite.
TCP/IP. Transmission Control Protocol/Internet Protocol. The protocol suite used in the Internet, intranets, and extranets. TCP provides transport functions, which ensures that the total amount of Bytes sent is received correctly at the other end. TCP/IP is a routable protocol, and the IP part of TCP/IP provides this capability.
G LOSSARY
Index
A
Administrative password, setting 129
Admission Control alarm status 185
Alarm status
B
Data Store 185 licensing 185 link state 185
memory paging 186 network bypass 186 optimization service 186
PFS
connection error 187 operation failed 187
System Disk Full 187 temperature 187
Asymmetric routing auto-detection
enabling 67 cache, enabling 67
Authentication
Auto-detection of asymmetric routing, about 66
Auto-discovery rules, overview of 27
Auxiliary Interface, setting 58
Bandwidth Optimization report 148
C
CIFS
transparent prepopulation
Configuring, CIFS optimization 31
Connected Appliances report 166
Connection forwarding
Connection history, viewing 167
Connection Pooling report, viewing 174
Connection pooling, enabling 44
Console
CPU Utilization alarm status 185
CSV file, exporting statistics to 196
Current connections
D
Data Store
Data store
Deny in-path rules, overview of 27
Discard in-path rules, overview of 27
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE 229
DNS
E
Email notification, setting 117
Enabling asymmetric routing
Enterprise MIB
Event and failure notification, setting 117
Exchange 2003 support, enabling 35
Exchange port, setting for firewalls 36
F
Fixed-target rules, overview of 27
H
Host name
Hosts, mapping to IP addresses 63
I
In-path
static network routes, setting 60
Interactive ports
Interface statistics, viewing 177
230
IP addresses, mapping host to 63
K
Kickoff, reset existing client connections upon startup 24
L
Layer 4 switch support, overview of 24
M
MAPI
Exchange
out-of-path deployments 34 ports 34 protocol options, setting 34
transparent prepopulation, enabling 36
Memory Paging
Message of the day
MIB file
Modifying
WCCP service group settings 96
MS-SQL protocol support, enabling 36
N
Neighbor Statistics report 181
Network Bypass alarm status 186
NFS
I NDEX
O
Optimization service alarm status 186
Overview
of asymmetric routing auto-detection 66
of CIFS transparent prepopulation 47
P
Pass-through rules, overview of 27
PFS
connection error alarm status 187
enabling shares 106 initial synchronization 106
operation failed alarm status 187
partition full alarm status 186
upgrading from v2.x to 3.x 107
Physical in-path, overview of 22
Port labels
Ports
commonly excluded 204 commonly optimized 204
interactive ports forwarded 205
secure automatically forwarded 206
Prepopulation
enabling shares 47 initial synchronization 47
modifying share details 49, 51
HP S TORAGE W ORKS EFS WAN A CCELERATOR M ANAGEMENT C ONSOLE U SER G UIDE
Primary interface
Q
QoS
classification, enabling 82 overview of 82 priorities 82
rule descriptions, modifying 89
service ports for multiple mappings 90
R
RADIUS authentication method, setting 127
RBT-Proto, common ports used by the system 203
Reports
Current Connections Details 172
Export Performance Statistics 196
Resetting existing client connections upon startup 24
Routing
asymmetric, auto-detection of 66
231
S
Secure ports
Secure-CIFs feature, enabling 33
Services, starting, stopping, restarting 144
Setting
email notification 117 event notification 117 failure notification 117
in-path static network routes 60
Setting connection forwarding 68
Simplified routing, enabling 92
SNMP
Software Version Check alarm status 187
Static network routes, setting 59
System
System Disk Full alarm status 187
T
TACACS+ authentication method, setting 127
TCP
statistics report, viewing 163
Technical support, contacting 202
Transparent prepopulation modifying
share details 49, 51 modifying share settings 49
overview
Traps, summary of SNMP traps sent 210
U
Upgrading
V
Virtual in-path, overview of 22
W
WCCP
service groups
service groups, enabling 94 setting service groups for 94
232 I NDEX
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 Contents
- 7 Introduction
- 7 In This Introduction
- 7 About This Guide
- 7 Types of Users
- 7 Organization of This Guide
- 8 Document Conventions
- 8 Hardware and Software Dependencies
- 9 Ethernet Network Compatibility
- 9 Antivirus Compatibility
- 10 Additional Resources
- 10 Related HP Documentation
- 10 Online Documentation
- 11 Related Reading
- 11 Contacting HP
- 11 Technical Support
- 11 HP Storage Web Site
- 13 Chapter 1 Overview of the HP EFS WAN Accelerator Management Console
- 13 In This Chapter
- 13 Connecting to the Management Console
- 13 Connecting to the Management Console
- 15 The Home: Welcome Page
- 16 Navigating in the Management Console
- 16 Navigating in the Management Console
- 18 Tabbed Pages and Menus
- 18 Saving Your Configuration
- 18 Restarting the HP EFS WAN Accelerator Service
- 18 Printing Pages and Reports
- 19 Displaying Online Help
- 19 Logging Out
- 21 Chapter 2 Configuring the HP EFS WAN Accelerator
- 21 In This Chapter
- 22 Setting Optimization Services
- 22 Enabling In- Path and Out-of- Path Support
- 25 Setting In-Path Rules
- 30 Modifying In- Path Descriptions
- 31 Configuring CIFS Protocol Support
- 34 Configuring MAPI Protocol Options
- 34 Optimizing MAPI Exchange in Out- of-Path Deployments
- 36 Configuring MS- SQL Protocol Options
- 38 Enabling the NFS- Application Streamlining
- 39 Modifying NFS Server Settings
- 42 Enabling HSTCP Protocol Options
- 44 Enabling Connection Pooling
- 46 Enabling Transparent Prepopulation
- 47 Enabling and Synchronizing Prepopulation Shares
- 49 Modifying Prepopulation Share Settings
- 50 Performing Manual Actions on Prepopulation Shares
- 52 Setting Host Parameters
- 52 Setting the Primary Interface
- 54 Setting In-Path Interfaces
- 54 Speed and Duplex Tips
- 58 Setting Auxiliary Interfaces
- 59 Setting Main Static Routes
- 60 Setting Static In-Path Routes
- 61 Setting the DNS
- 63 Modifying the Host Name
- 63 Mapping Hosts to IP Addresses
- 64 Setting Proxies
- 65 Setting Advanced Network Parameters
- 66 Enabling Asymmetric Routing Auto- Detection
- 68 Enabling Connection Forwarding
- 70 Enabling Encryption
- 73 Enabling Failover and Data Store Synchronization
- 77 Enabling NetFlow
- 79 Setting Peering Rules
- 79 Enabling Peering Rules for Serial Clustering
- 81 Enabling Quality of Service
- 85 Modifying a QoS Class
- 87 Setting QoS Marking
- 89 Modifying QoS Marking Descriptions
- 90 Modifying Service Ports
- 92 Enabling Simplified Routing
- 94 Enabling WCCP Groups
- 96 Modifying WCCP Group Settings
- 99 Enabling Proxy File Service
- 99 Enabling PFS
- 102 Adding PFS Shares
- 106 Enabling and Synchronizing Shares
- 107 Upgrading Shares from V2.x to V3.x
- 109 Modifying Share Settings
- 112 Performing Manual Actions on Shares
- 113 Creating Port Labels
- 113 Creating Port Labels
- 115 Modifying Ports in a Port Label
- 115 Setting Report Parameters
- 116 Setting Alarm Parameters
- 117 Setting Email Notification
- 119 Setting SNMP Parameters
- 120 Setting SNMP Trap Receivers
- 121 Setting Monitored Ports
- 123 Setting Logging Options
- 123 Setting Local Logging
- 124 Setting Remote Logging
- 125 Setting the Date and Time
- 125 Setting the Date and Time
- 126 Setting NTP Servers
- 127 Setting Authentication Methods
- 127 Setting General Authentication
- 129 Setting the Administrative Password
- 130 Setting the Monitor Password
- 131 Setting RADIUS Servers
- 133 Setting TACACS+ Servers
- 135 Modifying Web Settings
- 136 Setting the Message of the Day (MOTD)
- 137 Managing Licenses
- 137 Updating Your Licenses
- 138 Viewing Scheduled Jobs
- 139 Viewing Scheduled Jobs
- 139 Managing Configurations
- 142 Upgrading Your Software
- 144 Starting and Stopping Services
- 145 Rebooting the HP EFS WAN Accelerator
- 145 Shutting Down the HP EFS WAN Accelerator
- 147 Chapter 3 Creating HP EFS WAN Accelerator Reports and Logs
- 147 In This Chapter
- 147 Creating Performance Reports
- 148 Creating Bandwidth Optimization Reports
- 148 What this Report Tells You
- 148 About Report Graphs
- 149 About Report Data
- 150 Creating Data Store Hits Reports
- 150 What This Report Tells You
- 151 About Report Graphs
- 151 About Report Data
- 152 Creating Data Reduction Reports
- 153 What This Report Tells You
- 153 About Report Graphs
- 153 About Report Data
- 155 Creating NFS Statistics Report
- 155 What This Report Tells You
- 155 About Report Graphs
- 156 About Report Data
- 157 Creating Throughput Reports
- 157 What This Report Tells You
- 157 About Report Graphs
- 158 About Report Data
- 159 Creating Traffic Summary Reports
- 160 What This Report Tells You
- 160 About Report Graphs
- 161 About Report Data
- 162 Viewing Appliance Reports
- 162 Viewing Data Store Reports
- 163 What This Report Tells You
- 163 Viewing TCP Statistics Report
- 164 What This Report Tells You
- 165 Viewing Networking Reports
- 166 Viewing Connected Appliances Reports
- 166 What This Report Tells You
- 167 Viewing Connection History
- 168 What This Report Tells You
- 168 About Report Graphs
- 169 About Report Data
- 170 Viewing Current Connections
- 171 What This Report Tells You
- 172 Viewing the Current Connection Details Report
- 173 What This Report Tells You
- 174 Viewing Connection Pooling
- 175 What This Report Tells You
- 175 About Report Graphs
- 175 About Report Data
- 177 Viewing Interface Statistics
- 177 What This Report Tells You
- 178 Creating Link State Reports
- 179 What This Report Tells You
- 179 About Report Graphs
- 179 About Report Data
- 181 Creating Neighbor Statistic Reports
- 181 What This Report Tells You
- 181 About Report Graphs
- 181 About Report Data
- 182 Creating QoS Statistics Reports
- 183 What This Report Tells You
- 183 About Report Graphs
- 183 About Report Data
- 185 Viewing System Health Reports
- 185 Viewing Alarm Status Reports
- 187 What This Report Tells You
- 188 Creating CPU Utilization Reports
- 188 What this Report Tells You
- 188 About Report Graphs
- 190 Creating Memory Paging Reports
- 190 What this Report Tells You
- 190 About Report Graphs
- 192 Viewing Proxy File Service Reports
- 192 Viewing PFS Share Status Reports
- 192 What this Report Tells You
- 193 Viewing PFS Statistics
- 194 What this Report Tells You
- 194 About Report Graphs
- 194 About Report Data
- 196 Exporting Performance Statistics Reports
- 196 Exporting Performance Statistics
- 197 Viewing System Diagnostic Files
- 197 Viewing System Dump Files
- 198 Viewing System Snapshots
- 199 Viewing TCP Dump Files
- 200 Viewing HP EFS WAN Accelerator Logs
- 201 Viewing HP EFS WAN Accelerator Logs
- 202 Getting Help
- 202 Contacting Technical Support
- 202 Viewing Online Help Contents
- 203 Appendix A HP EFS WAN Accelerator Ports
- 203 In This Appendix
- 203 Default Ports
- 204 Commonly Optimized Ports
- 204 Commonly Excluded Ports
- 205 Interactive Ports Forwarded by the HP EFS WAN Accelerator
- 206 Secure Ports Forwarded by the HP EFS WAN Accelerator
- 209 Appendix B HP EFS WAN Accelerator MIB
- 209 In This Appendix
- 209 Accessing the HP EFS WAN Accelerator Enterprise MIB
- 210 SNMP Traps
- 211 HP EFS WAN Accelerator Enterprise MIB
- 225 Glossary
- 225 ARP
- 225 Bandwidth
- 225 Bit
- 225 Blade
- 225 Bottleneck
- 225 CIFS
- 225 Database Cursor
- 225 Default gateway
- 225 DHCP
- 225 Domain
- 225 DNS
- 225 Ethernet
- 226 FDDI
- 226 Filer
- 226 Gateway
- 226 Gigabit Ethernet
- 226 Hashing
- 226 Heartbeat
- 226 Heuristic
- 226 Host
- 226 Host address
- 226 Host name
- 226 HSRP
- 226 HTTP
- 226 HTTPS
- 226 Interface
- 227 Internet
- 227 IP
- 227 IP address
- 227 IPsec
- 227 Latency
- 227 Layer-4
- 227 MAPI
- 227 Microsoft Exchange
- 227 Netmask
- 227 Neural Network
- 227 NFS
- 227 NIS
- 227 OSPF.
- 228 Packet
- 228 Probe
- 228 Policy
- 228 Port
- 228 Router
- 228 SMB
- 228 SNMP
- 228 Switch
- 228 Tcl
- 228 TCP
- 228 TCP/IP
- 229 Index
- 229 A
- 229 B
- 229 C
- 229 D
- 230 E
- 230 F
- 230 H
- 230 I
- 230 K
- 230 L
- 230 M
- 230 N
- 231 O
- 231 P
- 231 Q
- 231 R
- 232 S
- 232 T
- 232 U
- 232 V
- 232 W