world-wide
033-54 Welding 2012_033-054 Welding1a 08.qxd 3/19/13 12:33 PM Page 15
Welding Accessories
Welding
Accessories
dimenSion SerieS
14-pin receptacle provides quick, direct connection to Miller 14-pin wire feeders and accessories. Internal digital voltage control (DVC) enables operator to preset weld voltage in the CV mode before striking an arc. Built-in arc control lets you get in tight without sticking the electrode. An electrode compensation circuit ensures consistent arc
control performance regardless of the electrode size. DC multiprocess capability provides versatility and outstanding arc performance in CV (MIG) and CC (Stick, TIG).
Power efficient for exceptional value and return on your investment. Fan-On-Demand ™ operates only when needed reducing noise, power consumption, and the amount
of airborne contaminants pulled through the machine. 115 V duplex receptacle provides 15 amps of auxiliary power. Hot Start ™ makes it easier to start difficult-to-start
Stick electrodes such as E-6010 and E-7018. Simple control panel features single range amperage/voltage adjustment. Provides easy, efficient operation. Digital voltmeter
and ammeter are easy to read, even at 30 ft (9.2 m). Line voltage compensation ensures consistent weld performance by keeping output power constant even if primary
input power varies by ±10%. Power cord strain relief provided for your convenience at installation. Remote on/off capabilities allow operator to turn power source on/off
from a distance. Remote voltage control allows operator to change voltage from feeder. Thermal overload protection light indicates power shutdown. Helps prevent
machine damage if the duty cycle is exceeded or airflow is blocked. PC board protection prevents the wire feeder power or other stray voltages (less than 115 VAC) from
harming the power source PC board. Enclosed circuit boards provide additional protection from contaminants resulting in longer service life.
dimenSion Sub arc SerieS
DC multiprocess capability provides versatility and outstanding arc performance in SAW (Submerged Arc) and CC (Stick, Carbon Arc Gouging). Internal digital voltage control
(DVC) enables operator to preset weld voltage in the CV mode before striking an arc. Built-in arc control lets you get in tight without sticking the electrode. An electrode compensation circuit ensures consistent arc control performance regardless of the electrode size. Hot Start ™ makes it easier to start difficult-to-start Stick electrodes such as E-6010
and E-7018. Line voltage compensation ensures consistent weld performance by keeping output power constant even if primary input power varies by ±10%. Simple control
panel features single range amperage/voltage adjustment. Provides easy, efficient operation. Digital voltmeter and ammeter are easy to read, even at 30 ft (9.2 m). Thermal overload protection light indicates power shutdown. Helps prevent machine damage if the duty cycle is exceeded or airflow is blocked. 14-pin receptacle provides quick, direct connection to Miller 14-pin wire feeders and accessories. 115 V duplex receptacle provides 15 amps of auxiliary power. Remote on/off capabilities allow operator to turn power
source on/off from a distance. Remote voltage control allows operator to change voltage from SAW Control. Power efficient for exceptional value and return on your investment.
Fan-On-Demand ™ operates only when needed reducing noise, power consumption, and the amount of airborne contaminants pulled through the machine. Enclosed circuit
boards provide additional protection from contaminants resulting in longer service life. Power cord strain relief provided for your convenience at installation.
trailblazer pro 350 d
The professional welder’s choice with higher outputs is designed to deliver the best arc performance with enough weld power to dominate larger diameter flux
cored wires and air carbon arc gouging thru 1/4 in carbons. Weld at Idle ™ —lock in idle and weld in DC up to 180 A. 12,000 watts of generator power is regulated to provide constant, strong power and very good motor starting characteristics. Power is independent of weld control settings so that the correct voltage is
available at all times. Even better weld performance with an arc that dominates the competition. In Stick mode, you get a smooth E7018 and a great E6010 arc
with Arc-Drive and Hot Start ™ standard. Great MIG/FCAW arc and machine idles with feeders hooked up. More stable AC TIG and excellent starts in DC scratch
start TIG. With a compact and lightweight design at only 998 lb, a smaller truck can be used, and related transportation costs will be reduced. Low height allows
the driver to see over the machine when mounted on a truck bed and the machine fits sideways in a standard pickup. Automatic Start at Idle ™ idles engine
immediately when started, extending engine life and reducing fuel consumption and noise. Toolless top and side engine access allows easy and faster maintenance
with little clearance space needed. Toolless remote oil drain is standard. Standard 14-pin receptacle easily connects feeders or remote controls for enhanced process
operation. Automatic idle in all processes, including MIG/FCAW with feeders to save fuel and reduce noise. 26 HP, 3-cylinder Kubota diesel engine with its
durable, proven liquid-cooled design is the world standard for small diesel engines. Engine shutdowns standard.
www.fmmafco.com
WORLD-WIDE
1.513.367.2151
CINCINNATI, OH – BIRMINGHAM, AL – CARSON CITY, NV – CHARLOTTE, NC
47
© 2013 - ALL RIGHTS RESERVED
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement