àà õ - Mobi.Control
CONTRIVE S.R.L.
Via Enrico Fermi 18 I-24040 SUISIO (Bergamo)
Tel. +39 (0)35 4948236 Fax +39 (0)35 4933759
B2510.EN / 1113
Do not install this unit near medical devices like pacemakers or hearing
aids. This unit may interfere with the operation of these devices.
www.contrive.mobi
Switch off this unit when flying.
Secure it so that it cannot be switched on inadvertently.
INDUSTRIAL GSM TERMINAL
This unit can be installed on any standard EN-50022 rail by simple snap-in.
For safe operation, the unit must be installed only by qualified personnel in an
enclosure which prevents accidental contact with hazardous voltages.
Protection degree IP40 must be guaranteed, raised to IP54 for open air application.
F. RJ socket - COM port
Do not install this unit near petrol stations, fuel depots, chemical plants or
blasting operations when this unit can disturb the operation of technical
equipment.
C. GSM operation blue LED indicator
¡ OFF
No power supply
¡ ON
Interference can occur if this unit is used near televisions, radios or
personal computers.
0681
If the device has been stored in a cold environment, condensation can occur.
Before starting operations, the device must be absolutely dry.
Thus, an acclimatization period of at least three hours must be observed.
This device complies with Part 15 of the FCC Rules
CONTAINS FCC ID N7NQ2687
USER GUIDE
Mobi.Modem 2510. 0 C . X 0
ANTENNA IS NOT PROVIDED AND
MUST BE PURCHASED SEPARATELY
INTERFACE
EIA RS-232 C
USB U
ANTENNA
EXTERNAL FME X
INTERNAL I
BATTERY
NO BATTERY 0
Li-Poly BATTERY B
*
RJ45 CONNECTOR AVAILABLE ON THIS UNIT PROVIDES
EIA RS-232 INTERFACE TO BE CONVERTED BY MEANS
OF EXTERNAL ADAPTER CABLE (INCLUDED) TO:
¡ SUB-D 9 POLE FEMALE DCE CONNECTOR, OR
¡ USB STANDARD PLUG TYPE A
FULLY COMPLIANT WITH THE USB 2.0 SPECIFICATION
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
¡ this device may not cause harmful interference, and
¡ this device must accept any interference received, including interference that may
cause undesired operation.
This device should be installed only by qualified personnel. Carefully read the
instruction manual in its entirety and keep it safe for future reference.
It is essential to know the information and comply with the instructions given in the
manual to ensure the fitting is installed, used and serviced correctly and safely.
This RF unit is not designed for and intended to be used in portable applications
(within 20 cm or 8 inches of the body of the user) and such uses are strictly prohibited.
This unit is not authorised for use as critical component in life-support devices or
systems unless a specific written agreement has been given.
If incorrectly installed in a vehicle, the operation of GSM device could interfere with
the correct functioning of vehicle electronics. Verification of the protection of vehicle
electronics should form a part of the installation.
Regulations must be considered to operate a vehicle’s light or horn on public roads.
No complex software or hardware system is perfect.
Bugs are always present in a system of any size.
In order to prevent danger to life or property, it is the responsibility of the system
designer to incorporate redundant protective mechanism appropriate to the risk
involved.
All units are 100% functionally tested. Specifications are based on characterisation
of tested sample units rather than testing over temperature and voltage each unit.
Contrive disclaims all liability for damage to the fitting or to other property or persons
deriving from installation, use and maintenance that have not been carried out in
conformity with this instruction manual, which must always accompany the fitting.
PRODUCT DESCRIPTION
Your Mobi.Modem is the product of advanced engineering, design and craftmanship
and should be treated with care. The suggestion below will help you to enjoy this
product for many years.
Mobi.Modem is an industrial DIN rail GSM modem for for the transfer of data, SMS
and faxes in GSM networks. Industrial standard interface and an integrated SIM card
reader mean it can be used rapidly, easily and universally to quickly implement new
applications in telemetry, telematics and remote control. All interfaces are integrated
in the housing.
The connections are suitable for use in domestic and industrial environments.
Both fixed and mobile applications are allowed, as defined below:
Fixed means that the device is physically secured at one location and is not able
to be easily moved to another location.
Mobile means that the device is designed to be used in other than fixed locations
and generally in such a way that a separation distance of at least 20 cm (8 inches)
is normally maintained between the transmitter’s antenna and the body of the user
or nearby persons.
Do contact an authorized service center in the unlikely event of a fault in the unit.
Module switched ON
Not registered on the network,
missing SIM or invalid PIN
¡ SLOW FLASH
C
In order to avoid possible damage, we recommend that you only use the
specified accessories.
These have been tested and shown to work well with this unit.
CARE AND MAINTENANCE
¡ Do not expose the unit to any extreme environment where the temperature or
humidity are out of operating range.
¡ Do not use or store the unit in dusty or dirty areas.
¡ Do not use chemical cleaning agent on the unit or the SIM card.
¡ Do not attempt to disassemble the unit or remove any part or label.
¡ Do not expose the unit to water, rain or spilt beverages. It is not waterproof.
¡ Do not abuse the unit by dropping, knocking or violenty shaking it.
Rough handling can damage it.
¡ Do not place the unit alongside computer discs, credit or travel cards or other
magnetic media. The information contained on these devices may be affected.
¡ This unit is under your responsibility. Please treat it with care respecting all local
regulations. It is not a toy: keep it in a safe place and out of the reach of children.
¡ Treat the SIM card with the same care as your credit card: do not bend or scratch
or expose it to static electricity.
¡ Keep your unlock and PIN codes in safe place.
PERMANENTLY
PRODUCT FEATURES
Quad band GSM / GPRS / EDGE communication with manual / automatic selection
on bands 850 / 900 / 1800 / 1900 MHz for data, sms, data and voice applications.
Class 4 ( 2W for GSM850 and EGSM900 )
Class 1 ( 1W for DCS1800 and PCS1850 )
Temperature:
-40 to 85°C
-20 to 60°C recommended for battery
Relative humidity:
operating 5 to 95% non-condensing
storage & transport 5 to 95% condensation allowed outside
Enclosure:
EN-50022 rail 4 modules, polycarbonate, UL94 -V0
Overall dimensions: mm 71 x 90 x 48 ( W x H x D )
Weight:
200 g
Degree of protection: IP 40 (EN-60529 / IEC 529) properly fitted
200ms ON / 2s OFF
Module switched ON
Registered on the network
¡ QUICK FLASH
200ms ON / 600ms OFF
àà
13 14 15 16 17 18 19 20
E
F
Module switched ON
Registered on the network
Communication in progress
E. Power supply terminals
2
2 x 2,5mm (AWG14)
X. Antenna connector
NOT AVAILABLE FOR IPEX VERSION
õ
STANDARD VERSION: 2510.0C.X0
OTHER OPTIONS ON REQUEST
*
r
RJ45 SOCKET
INSTALLATION
SAFETY INFORMATION
X
Disconnect all power
supplies and battery before
to insert or remove the
SIM card.
Replace the plastic cover
before to operate the unit.
F. SIM card holder
3V and 1,8V SIM card allowed
8
V24
RS232
1.RXD
104
BB
RECEIVE DATA
DCE > DTE
2.GND
101
AB
SIGNAL
GROUND
3.TxD
103
BA
TRANSMIT DATA
DCE < DTE
> +2.4V HI:ACTIVE
< +1.5V LO
4.SPK
---
--
SPEAKER 2
OUTPUT+
8 ohm
2 Vpp
5.CTS
106
CB
CLEAR TO SEND
DCE > DTE
> +5.0V HI:ACTIVE
< -5.0V LO
6.SPK
---
--
SPEAKER 2
OUTPUT-
8 ohm
2 Vpp
7.RTS
105
CA
REQUEST TO SEND
DCE < DTE
> +2.4V HI:ACTIVE
< +1.5V LO
8.+5V
---
--
POWER
SUPPLY
5 Vdc
500 mA
Communication:
DESCRIPTION
PARAMETERS
> +5.0V HI:LOGIC 0
< -5.0V LO:LOGIC 1
RS-232 (DCE)
300 ... 115200 bit/s
7/8 data bits, 1/2 stop bits, 1 parity bit, 10/11 bit char length
Software handshake, Hardware handshake
Mobi.Modem is a DCE (Data Communication Equipment).
The EIA-RS232 interface is the interface for the application software providing the
connection to DTE (Data Terminal Equipment).
The EIA-RS232 interface is implemented as a 8 pole RJ45 modular socket.
Circuit type SELV, max 15 m length, shielding not required.
The customer application communicates with Mobi.Modem by means of AT cellular
commands.
AT commands manual is availble for download at www.contrive.mobi
EIA-RS232 VERSION
Mobi.Link cable 2505.00.01 is provided to convert RJ45 to standard DB9 connector.
SIM PIN
If the PIN code is enabled use AT+CPIN
command to unlock the SIM card.
Enable or disable the verification of PIN
code either with the help of a mobile
phone or with the command AT+CLCK.
WARNING
If you provide a wrong PIN number the device will not operate.
If you enter the PIN 3 times incorrectly, SIM card will lock up and you must
provide the PUK (PIN Unblocking Key).
Output power:
USB VERSION
Mobi.Link cable 2505.00.03 is provided to convert RJ45 to standard USB type A plug.
Mobi.Modem can receive the power supply from this USB interface.
A Personal Computer USB port can keep the unit alive if capable of sourcing 500 mA peak
current. The unit can receive power supply both from terminal connector and RJ plug at
same time.
POWER SUPPLY
This unit can be supplied either by alternating or direct current, polarity independent,
in a wide voltage range. Power supply connection terminals 19 and 20.
The power supply must not be shared with other equipment: suggested power
supply source is a simple 12VAC / 10VA transformer.
Supply Voltage
9,5 ... 35 V DC
9,5 ... 27 V AC
Power consumption
< 200 mW IDLE
PEAK
<5W
An automatic 2-pole circuit breaker or equivalent protection capable of disconnecting circuit in the event of short circuit or over-current condition should be placed
on the AC mains side of power supply unit. Maximum permissible connection length
between device and low voltage supply source is 3 m.
48
1
POWER SUPPLY AND COM PORT MUST
MEET THE DEMANDS PLACED ON
SELV (SAFETY EXTREMELY LOW VOLTAGE)
CIRCUITS ACCORDING TO EN60950 / IEC950
WARRANTIES
CONTRIVE GUARANTEES FOR TWO YEARS FROM THE DATE OF MANUFACTURE OF
ITS PRODUCT TO REPLACE, OR, AT ITS OPTION, TO REPAIR ANY PRODUCT OR PART
THEREOF WHICH IS FOUND DEFECTIVE IN MATERIAL OR WORKMANSHIP OR WHICH
OTHERWISE FAILS TO CONFORM TO THE DESCRIPTION OF ITS SALES ORDER.
CONTRIVE MAKES NO WARRANTY OF MERCHANTABILITY OR ANY OTHER
WARRANTY EXPRESS OR IMPLIED. IN NO EVENT SHALL CONTRIVE BE LIABLE FOR
CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY NATURE WHICH MAY ARISE IN
CONNECTION WITH SUCH PRODUCTS.
THE WARRANTY DOES NOT APPLY IN CASE OF IMPROPER USE
Please perform the following tasks after receiving the product :
¡ Inspect the unit for damage.
If the unit appears damaged upon receipt, contact the shipper immediately.
DIMENSIONS [mm]
71
90
¡ Verify receipt of the correct unit by checking the label on the right side of the unit.
¡ If you have received the wrong model or the device does not function properly,
contact your supplier.
© COPYRIGHT 2012 CONTRIVE SRL ITALY. SOME RIGHTS RESERVED.
INFORMATION CONTAINED IN THIS DOCUMENT ARE SUBJECT TO CHANGE WITHOUT
NOTICE. PRODUCT NAMES, CORPORATE NAMES OR TITLES USED WITHIN THIS
DOCUMENT MAY BE TRADEMARKS OR REGISTERED TRADEMARKS OF OTHER
COMPANIES AND ARE MENTIONED ONLY IN AN EXPLANATORY MANNER TO THE
READERS’ BENEFIT, AND WITHOUT INTENTION TO INFRINGE.
WHILE EVERY EFFORT HAS BEEN MADE TO MAKE SURE THE INFORMATION IN THIS
DOCUMENT IS CORRECT, CONTRIVE CAN NOT BE LIABLE FOR ANY DAMAGES
WHATSOEVER FOR LOSS RELATING TO THIS DOCUMENT.
DEFAULT SETTINGS
Q:0 V:1 S0:000 S2:043 S3:013 S4:010 S5:008
+CR:0 +CRC:0 +CMEE:0 +CBST:0,0,1
+SPEAKER:1 +ECHO:0 &C:1 &D:2 %C:0
+IPR:115200 +ICF:3,4 +IFC:2,2
Q:0
V:1
Result codes NOT suppressed
Verbose mode
S0:000
S2:043
S3:013
S4:010
S5:008
Auto answer disabled
Character for escape sequence (+)
Command line termination character (Cr)
Response formatting character (Lf)
Command line editing character (BS)
OPTIONAL BATTERY
The antenna must be connected to the RF interface, implemented as a 50W connector available in 2 different options:
¡ External FME male coaxial jack at the end of a short RG178 cable stub exiting
from the bottom left side of the unit.
¡ Internal IPEX connector suitable for embeddable antennas.
This unit could be equipped with an high efficiency Lithium-Ion Polymer battery
having a long life, that largely depends on temperature and frequency of main power
failures, used in normal condition can last several years.
Battery equipped devices are provided with removable top cover enclosure.
The antenna must fulfil the requirements given below:
Frequency TX
880 to
915 MHz
1710 to
1785 MHz
824 to
849 MHz
1850 to
1910 MHz
Frequency RX
925 to
960 MHz
1805 to
1880 MHz
869 to
894 MHz
1930 to
1990 MHz
Impedance
VSWR
50 ohms
RX max
1.5 : 1
TX max
1.5 : 1
Polarization
Linear
Typical gain
0 dBi in one direction at least
+CR:0
+CRC:0
+CMEE:0
+CBST:0,0,1
+SPEAKER:1
+ECHO:0
&C:1
&D:2
%C:0
Extended reports disabled
Extended result codes disabled
Extended error indication disabled
Bearer autobauding, async, transparent
Speaker output 2 (available at RJ45 connector)
Echo cancellation disabled
Carrier detect indication
Call released when DTR drop to OFF
Data compression disabled (no V24 bis)
The gain must not exceed 8,4dBi @ 850MHz and 3,5dBi @ 1900MHz.
We recommend a VSWR max of 1.5:1 although a VSWR max of 2:1 can be accepted
without affecting performance and certification.
The DC impedance is floating but there is no problem when using antennas that
present a short to ground.
+IPR:115200
+ICF:3,4
+IFC:2,2
115200 baud
8 data 1 stop No parity
RTS / CTS (Hardware handshake)
Some custom AT commands are available for a simplified use of advanced features:
CUSTOM AT COMMANDS
AT#SMS=n,t
Each setting can be modified with specific AT command.
This and many other settings related to active profile can be written to internal non
volatile memory by means of command AT&W.
The command AT&F will restore the factory settings, overwriting any profile
previously set with command AT&W.
AT#CMSS=i,n
QUICK START
example
Connect a personal computer running a terminal emulation program or any other
DTE to the serial interface providing the factory default communication settings:
example
AT#CMGW=i,n,t
¡ 115200 bit/s, 8 databits, 1 stop bit and no parity.
(AT+IPR and AT+ICF commands to edit settings).
¡ RTS / CTS flowcontrol enabled
( AT+IFC command to edit settings).
Hard or soft flowcontrol MUST be enabled when using high speed rates.
Follow the steps below to get the unit up and running as quickly as possible:
¡ Insert a valid SIM card.
example
¡ For X-types devices make sure that the antenna is connected.
¡ Verify that the antenna is placed in the best position possible.
¡ Connect the battery, if any.
¡ Power on the unit and make sure that the PIN code of the SIM card is disabled
either with the help of a mobile phone or with the command AT+CLCK.
If the PIN code should be enabled make sure to enter the correct PIN code
with the command AT+CPIN.
After entering the PIN some SIM user data files are loaded into the device.
Please be aware that it might take some time to read a large phonebook.
¡ Check that the the GSM operation led indicator [C] is flashing, this means that
the unit has a connection to network and that it is registered.
¡ Verify the registration status by means of AT+CREG? command:
+CREG:0,0 means not registered
+CREG:0,1 means registered with Home Network
+CREG:0,5 means registered roaming
¡ Check the received signal quality by means of AT+CSQ command: the value of
the first parameter reported from the +CSQ command should be more than 10.
+CSQ:99 means no signal available.
¡ Configure the unit with appropriate commands as needed in the specific
application.
Commands always start with AT (which means ATtention) and finish with a <CR>
character (carriage return).
Responses start and end with <CR><LF> (except for the ATV0 DCE response
format) and the ATQ1 (result code suppression) commands.
Send SMS from Mobi.Modem internal memory
i memory index (1...99)
n destination phone number (overrides stored one, if any)
AT#CMSS=1
AT#CMSS=2,+44123456
AT#APN=myapn.com,myuser,mypass
Returns current APN settings
AT#SMTP=n,p,u,w Set Outgoing Mail Server Address
n Server address
p Server port (optional, default 25)
u User name (optional, if required by Server)
w Password (optional, if required by Server)
Returns current SMTP settings
AT#EMAIL=s,t,r
Send simple Email to destination
s Sender’s Email address
t Text to be sent (into Subject line)
r Recipients Email address (up to 10 separated by comma)
AT#EMAIL=myemail.com,”Hello”,email1.com,email2.com
Use Mobi.Voicer software utility to generate audio files from SMS text stored within
the Mobi.Modem internal memory. Once text has been converted to speech it will be
possible to use the following commands during a phone call:
AT#PLAY=i,r
example
AT#PLAY=2,0
(repeat continuously until hangup)
AT#STOP
¡ If command syntax is correct but transmitted with wrong parameters, the
+CME ERROR:<Err> or +CMS ERROR:<SmsErr> string is returned with
adequate error codes if CMEE was previously set to 1. By default, CMEE
is set to 0, thus the error message is only “ERROR”.
Any key pressed by the other party during a phone call will be reported issuing an
unsolicited code:
DTMF:k
¡ If the command line has been executed successfully, an “OK” string is returned.
Use the following command to enable/disable custom commands:
In some cases, such “AT+CPIN?” or (unsolicited) incoming events, the product does
not return the “OK” string as a response.
AT+WOPEN=1
AT+WOPEN=0
Stop current audio file
k
0-9 * #
Custom commands enabled (factory default)
Custom commands disabled
GSM Data features:
¡ Circuit Switched Data Asynchronous
transparent or non-transparent up to 14 400 bit/s
¡ Fax group 3 compatible
GPRS Data features: ¡
¡
¡
¡
Multislot Class 10
Multislot Class 2 supported
Coding scheme: CS1 to CS4
PBCCH (Packet Broadcast Control Channel) support
EGPRS Data features: ¡
¡
¡
¡
Multislot Class 10
Multislot Class 2 supported
Coding scheme: MCS5 to MCS9
PBCCH (Packet Broadcast Control Channel) support
Disconnect the battery if the
device is put out of service.
¡ SMS 160 characters text or PDU
¡ Point to point (MT/MO)
¡ Cell broadcast
GSM Supplementary ¡ Call Forwarding, Call Barring, Call Waiting, Call Hold
Services:
¡ Multiparty
¡ USSD (Unstructured Supplementary Services Data)
Internet services:
¡
¡
¡
¡
¡
¡
¡
¡
¡
TCP
UDP
FTP
HTTP
POP3
SMTP
SNMP
SSL
MMS
[1] Speaker output routed to RJ45 connector
Microphone input not implemented
DECLARATION OF CONFORMITY
4. Replace the front cover to
close the unit.
R&TTE Directive 1999/5/EC
Company identification: Manufacturer: Contrive, Srl
Via Enrico Fermi 18 24040 Suisio Italy
Product identification:
Brand:
Contrive
Equipment name: Mobi.Modem
Equipment type: GSM/GPRS modem
We declare on our sole responsibility, that the product described above is in
compliance with the essential requirements of the 1995/5/EC Directive:
BATTERY SPECIFICATIONS
K
4,2V FULL CHARGE
Voltage
3,7 V
Capacity
> 320 mAh 1.26 Wh
Temperature -20...60°C 0...45°C CHARGING
¡ Health and safety requirements pursuant to clause 3.1a:
EN 60950-1:2006
EN 60950-1 A11:2009
EN 60950-1 A1:2010
EN 60950-1 A12:2011
EN 50385:2002
¡ Protection requirements concerning EMC clause 3.1b:
EN 301 489-7 V1.3.1:2005-11
EN 301 489-1 V1.9.2:2011-09
Before a long period of inactivity switch off
the unit to prevent deep discharge of the
battery by issuing the command AT+CPOF
¡ Measures for the efficient use of the radio frequency spectrum clause 3.2:
EN 301 511 V9.O.2:2003-03
NOTE:
Battery status is reported at any time by the
LED located near the connector:
OFF
OFF
Charge OFF
RED
OFF
Charge in progress
OFF
GREEN
Charge completed
RED
GREEN
Bad or NO battery
RECYCLING OPTIONS
AVAILABLE IN YOUR AREA
MUST BE CONSIDERED
WHEN DISPOSING
BATTERIES !
DO NOT DISPOSE OF
IN FIRE !
Play an audio file previously stored during a phone call
i index of stored audio file (1...99, same as SMS index)
r repeat (1...32000 times, 0 endless)
¡ If command syntax is incorrect, the “ERROR” string is returned.
¡ 1.8V and 3V SIM
¡ U-SIM compatible
3. Plug / unplug battery
connector from socket [K].
AT#SMTP=mysmtp.com,587,mailuser,mailpass
AT#SMTP?
example
2. Pull the front cover and
keep it in a safe place.
1
SIM Interface:
Disconnect power supply and
all live circuits. Remove front
cover to access the inside :
1. Push with two fingers on
top and bottom sides of
front cover to release it.
AT#CMGW=1,+44123456,”Warning”
AT#CMGW=44,,”Failure”
Set Internet Access Point Name
n APN address
u User name (optional, if required by APN)
w Password (optional, if required by APN)
example
1
Save SMS into Mobi.Modem internal memory
i memory index (1...99)
n destination phone number (optional)
t text to be sent (up to 160 characters)
Read all SMS from Mobi.Modem internal memory
AT#APN?
If the battery is already connected, you just need to provide power supply to operate
Mobi.Key. The battery charging process will start.
If the battery is not connected, proceed as follows:
2
Voice features (GSM): ¡ Telephony, Emergency calls
[1]
¡ Full Rate, Enhanced Full Rate, Half Rate,
Adaptive Multi Rate
¡ Echo cancellation and noise reduction
¡ Dual Tone Multi Frequency (DTMF) function
¡ Full duplex handsfree
SMS features:
Overall dimensions: mm 71 x 90 x 58 ( W x H x D )
AT#SMS=+44123456,”Alarm”
AT#APN=n,u,w
example
90
71
Send SMS
n destination phone number
t text to be sent (up to 160 characters)
AT#CMGR
¡ Verify that the correct services are enabled.
(e.g. incoming and outgoing DATA service, SMS service center, FAX service).
58
õ
It’s possible to read current settings from the unit by means of AT&V command.
A device with factory settings will return:
VOICE / DATA / FAX / SMS
ANTENNA
This product may load and run custom specific firmware.
Use the following commands to retrieve advanced information:
AT#DVC
Returns device type
AT#VER
Returns custom firmware version
AT#DOP
Returns Date of Production
AT#NOT
Returns additional information related to device
Complete literature for this unit available here:
www.contrive.mobi/mobimodem
Class B equipment (domestic) emission level applied.
Class A equipment (industrial) immunity level applied.
and all tests were carried out
EUROFINS Product Services, GmbH
Notified Body:
Storkower Strasse 38C
D-15526 Reichenwalde
0681
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES
Operation is subject to the following two conditions:
1 this device may not cause harmful interference, and
2 this device must accept any interference received, including interference
that may cause undesired operation.
REFERENCE STANDARD:
FCC Part 15 part A Code of Regulations Part 15 (Radio Frequency Devices),
Subpart A (General) of the Federal Communication
Commission
FCC Part 15 part B Code of Regulations Part 15 (Radio Frequency Devices),
Subpart C (Unintentional Radiators) of the Federal
Communication Commission
ANSI C63.4
American National Standard for Methods of Measuring of
Radio-Noise Emissions from Low-Voltage Electrical and
Electronic Equipment in the Range of 9 kHz – 40 GHz
Suisio, Italy March 21, 2013
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement