Switching mode
Basic operation
Switching mode
The main unit can be used when the vehicle's ignition switch is on or in the ACC position.
• The main unit supports use of a remote control. The optional remote control is sold
separately and can be purchased at your local retailer. Refer to page 96 for instructions on
operation of the remote control.
Switching the mode
 Press
(SOURCE) MENU .
• The AUDIO MENU screen will be displayed.
 Touch
FM .
• The various audio modes can be
selected by touching the
corresponding touch switches.
• When the navigation screen is being
displayed before pressing
(SOURCE) MENU , the selected
mode will be displayed on-screen over
the background.
On-screen display
Displaying operation screen
 Press
20
CONT .
Basic operation
Operation screen of each mode
The operation screen for each mode will appear as shown below.
● FM radio operation screen
● HD RADIO (IBOC) operation screen (optional)
● SIRIUS operation screen (optional)
Basic
operation
● AM radio operation screen
● CD player operation screen
● DVD player operation screen
● MP3 player operation screen
● CD changer operation screen (optional)
● VTR operation screen (optional)
When the operation screen for DVD or video (VTR) has not been operated for 6 seconds or
more, the operation screen will automatically be canceled.
21
Basic operation
Adjusting the volume
Adjusting main volume
 Press the VOLUME switch.
Pressing
will increase volume.
Pressing
will decrease volume.
• Each press of the switch will change
the volume by two steps. When the
volume reaches 50 or higher, the
switch will change the volume by one
step. Holding the switch will continue
to change the volume.
22
VOLUME switch
Basic operation
Adjusting sound quality
DSP
EQ
Basic
operation
To adjust sound quality, touch the DSP, EQ or POS switch while the operation screen for a
mode is displayed. Adjustments made in any mode will be saved and applied to all modes.
POS
In the DVD mode, display the sound quality adjustment switches by pressing
from the operation modes, and then SET . In the VTR mode display them
either by pressing CONT or by touching the screen.
23
Basic operation
Adjusting sound quality
Setting DSP (acoustics)
The DSP function reproduces the sensation of various factory set performance environments
by adding reverberation to the music being played.
DSP mode setting
 Touching the DSP touch switch
brings up the acoustics mode
screen as shown.
• After making settings, touch BACK .
The acoustics mode adjustments will
be saved and the system will return to
the previous operation screen.
Touch switch
DSP Environment
Touch switch
DSP Environment
CONCERT
Concert hall
CLUB
Disco, Club
LIVE
Live performance
arena
THEATER
Movie theater
CATHEDRAL
Church with echo
OFF
DSP OFF
Adjusting, saving DSP (acoustics)
The factory set DSP (acoustics) level for each mode can be adjusted to preference and
saved.
 Touch
or
at the right of the
screen while in the acoustics mode
to be adjusted.
• There are five + and five - adjustment
levels available.
 Touch the switch for the acoustics
mode that has been adjusted until
a beep is heard.
24
Resetting DSP (acoustics) levels
 Touch OFF until a beep is heard.
• The accoustic level will be returned to default value (the default value is "0").
Basic
operation
Default settings for the currently adjusted and saved DSP (acoustics) level can be reset.
When adjusting the level for the currently selected DSP (acoustics) mode, the
level will not be saved for other acoustics modes.
25
Basic operation
Adjusting sound quality
Adjusting EQ (equalizer)
Adjusts sound quality to preferred characteristics according to the music genre and audio
source.
Setting sound quality
Each factory set equalizer pattern can be selected and adjusted to preference.
 Touching the touch switch brings
up the equalizer mode screen as
shown in the table.
• After making settings, touch BACK .
The equalizer mode adjustments will
be saved and the system will return to
the previous operation screen.
Touch switch
Equalizer mode types
FLAT
No EQ correction
EQ1
Effective pattern for POPS
EQ2
Effective pattern for ROCK
EQ3
Effective pattern for JAZZ
EQ4
Effective pattern for CLASSIC
EQ5
Effective pattern for VOCAL
The default setting is
26
EQ3
.
Adjusting and saving equalizer (EQ) patterns
 Touch the screen and slowly draw
the image of the preferred
equalizer curve with your finger.
Basic
operation
Apart from these preset equalizer patterns, you can adjust and record other equalizer
patterns to suit your own sound preferences.
 To make fine adjustments, touch
the switch for the frequency to be
adjusted.
 Touch
or
at the right of the
screen to adjust.
 Choose from touch switches EQ1 to EQ5 for saving the settings and then
touch and hold the switch until a beep is heard.
• The saved equalizer curve can be used for other settings.
• After making settings, touch BACK . The equalizer mode adjustments will be saved
and the system will return to the previous operation screen.
Resetting EQ patterns
Currently saved equalizer patterns and factory set equalizer patterns can be returned to the
default values.
 Touch
FLAT until a beep is
heard.
• The equalizer pattern will be reset to
default values (factory default values).
27
Basic operation
Adjusting sound quality
Setting POS (position selector)
The stereophonic position for obtaining optimum acoustic effects can be adjusted to match
the number and position of passengers.
In addition, front-to-back, right-to-left volume balance can be adjusted for the selected
position.
 Touching the image of a seat
shown on the POS setting screen
will change the position.
• The selected position will change its
color to orange. Touching the seat
again will cancel the selection. The
four positions shown by the table
below can be set.
• Touching OFF will cancel all settings.
• After making settings, touch BACK . The position will be saved and the system will
return to the previous operation screen.
Touch switch
Function
Touch switch
Function
Acoustics optimized for
driver's seat
Acoustics optimized for
both front seats
Acoustics optimized for
passenger's seat
Acoustics optimized for
rear seats
• This setting cannot be done at the same time as adjustment of the volume
balance (see next page).
• The main unit is configured for vehicles with a left-side driver's position.
28
Adjusting volume balance
The set position for front-to-back, right-to-left volume balance can be adjusted.
BAL
FAD on the
Basic
operation
 Touch
POSITION setting screen to
display the volume balance
adjustment screen.
 Touch the screen at the preferred
balance point.
• To make fine adjustments, touch
,
,
,
.
• Touching CENTER will set the
volume balance to the center position.
• After making settings, touch BACK .
• The set volume balance will be saved
and the system will return to the
previous operation screen.
• To set the position again, touch POS
and repeat the steps above.
• This setting cannot be done at the same time as POS (position selector)
adjustment, described on the previous page.
• Touching and holding
,
,
or
while making fine adjustments will
adjust values in a continuous action. However, adjustment will lock when it
reaches the center value, and
continue adjustment.
,
,
or
must be pressed again to
29
Basic operation
Adjusting sound quality
Setting the BEEP tone
The guide tone that is emitted when touching a panel switch or touch switch can be set to on
or off.
 Touch
 Touch
SETTING on the INFORMATION screen.
ON or OFF of GUIDE TONE.
• The pressed touch switch will become green.
• Touching OFF will cancel (turn off) the guide tone.
 Touch
ENTER .
Muting sound
Sound from the audio system can be temporarily muted.
 Press
MUTE .
• Volume will become zero.
• Pressing MUTE switch again will
return to previous volume.
• The VOLUME display will flash during
mute.
MUTE switch
The MUTE function will be canceled on pressing the + VOLUME switch (it is
unaffected by pressing the – switch).
30
Basic operation
Setting LOUDNESS
 Touch
SETTING on the
INFORMATION screen.
Basic
operation
Audio can be modulated to correct for insufficient low and high sounds when listening at low
volume.
 Touch
ON or OFF of
LOUDNESS.
• The pressed touch switch will become
green.
 Touch
ENTER .
Setting subwoofer level
When a woofer is connected, the preferred output level for audio can be set.
To connect a woofer, an optional cable is required.
 Touch
SETTING on the
INFORMATION screen.
 Touch
or
of WOOFER
CONT.
 Touch
ENTER .
31
Basic operation
Setting the background screen
The background for the audio screen, information screen and navigation screen can be
changed to a preferred wallpaper.
Setting the wallpaper
Changing the wallpaper
 Touch
SETTING on the
INFORMATION screen.
 Touch
1 , 2 or 3 of WALL
PAPER.
• The pressed touch switch will become
green and the wallpaper (background)
will change.
 Touch
32
ENTER .
Basic operation
Adjusting the background screen
Setting the opening screen
Changing the image on the opening screen
 Insert a CD-R/RW disc that includes your favorite image.
Basic
operation
The image displayed on the opening screen (which is displayed when the power is turned
on) can be changed to your favorite one stored in a CD-R/RW.
• It would take approximately 30 seconds to read the image data. While the image
data is being read, do not operate the main unit and the ignition key.
 Touch Opening Image Change .
 Touch the image you want to display on the opening screen.
 Touch OK .
• Be sure to eject the CD-R/RW disc that includes the image data.
About usable image data
The format of disc and image data that can be used on the opening screen are shown in the
table below. If your disc and/or data does not meet the conditions below, the file names may
not be listed nor displayed correctly.
CD-R/RW
Disc format
ISO9660 (MODE1)
File size
Smaller than 100 KB
File name
ISO9660 LEVEL 2 (Up to 31 bytes)
File extension
.jpg (Non-JPEG2000-compliant)
Writing method
Single-session only
Image size
416 (W) X 240 (H) dots (Max.)
The files in the root directory (top-most directory) only.
Displayed file
*When storing the image data in a CD-R/RW disc, make a text file named "CSM.txt" (any
content/text is OK) and store it together with the image data.
• If the image size is larger than the condition above, the image cannot be previewed or
imported.
• If the image size is smaller than the condition above, the image will be displayed at the
center of screen.
• Only one image data can be imported at a time.
33
Basic operation
Adjusting/setting the screen
Quality adjustments can be made for the images such as the audio operation screen,
navigation screen and DVD or VTR (optional).
Displaying the image adjustment screen
Contrast, brightness and other picture settings can be adjusted to match preferences for
viewing DVD video or the audio operation screen.
To make viewing easier, the display switches between day screen/night screen according to
whether the vehicle lights (parking lights, taillights, license plate lights) are on/off.
(Default settings)
• When vehicle lights are on: [Night screen is displayed]
• When vehicle lights are off: [Day screen is displayed]
[Audio operation screen]
● Day display [Vehicle lights are off]
● Night display [Vehicle lights are on]
[DVD/VTR Screen]
● Day display [Vehicle lights are off]
34
● Night display [Vehicle lights are on]
DISP on the audio mode screen or DVD/VTR screen.
ENTER after making any adjustments.
• If no adjustments are made after 20 or more seconds, the image quality adjustment
screen will be canceled.
● When adjusting audio operation screen
Basic
operation
 Press
 Touch
● When adjusting DVD/VTR screen
How to switch to daytime display when the lights are ON
 The day screen and night screen will be switched each time
DAY is
pressed.
● When adjusting audio operation screen
● When adjusting DVD/VTR screen
Turning off the screen
 Touch OFF .
• Press CONT or NAVI to return to the original screen.
35
Basic operation
Adjusting/setting the screen
Adjusting image quality
The day screen and night screen can be separately adjusted (on the audio operation screen,
the navigation screen, and the DVD/VTR screen).
● When adjusting audio operation screen or
navigation screen
● When adjusting DVD/VTR screen
■ CONTRAST
 Touch
to strengthen contrast,
to weaken contrast.
■ BRIGHT
 Touch
to make lighter,
to make darker.
■ COLOR (for DVD/VTR screen only)
 Touch
to strengthen green color,
to strengthen red color.
■ TINT (for DVD/VTR screen only)
 Touch
to make tint darker,
to make tint lighter.
Switching screen mode
 Touch
WIDE on DVD or VTR
operation screen.
 Touch
NORMAL , WIDE1 ,
WIDE2 or WIDE3 .
• This selects the wide mode.
 Touch
36
BACK .
● Returns to the DVD or VTR operation screen.
Basic
operation
■ NORMAL mode
■ WIDE 1 mode
The screen is shown with vertical to
horizontal ratio of 3 to 4 (normal TV
screen size) and side edges are black.
The screen for vertical to horizontal ratio
of 3 to 4 (normal TV screen size) is
uniformly expanded in the left and right
directions.
■ WIDE 2 mode
■ WIDE 3 mode
The screen for vertical to horizontal ratio
of 3 to 4 (normal TV screen size) is
uniformly expanded in the left and right
directions (except for the central section
of the screen).
The screen for vertical to horizontal ratio
of 3 to 4 (normal TV screen size) is
uniformly expanded in the upward,
downward, left and right directions.
Viewing of wide screen modes is permitted when limited to the personal
entertainment of the user, but caution is required when using technologies such
as image compression and expansion for the purpose of commercial benefit or
public presentation may infringe upon the rights of the copyright holder being
protected by applicable copyright law.
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising