media

Light-Manager Air

Quickstart Guide

Overview and scope of delivery

Thank you for choosing the Light-Manager Air. The Light-Manager is the control center for your wireless home automation. For this purpose the device integrates several transmitter and receiver modules as there are

•

•

Radio frequency on 433 MHz

Radio frequency on 868 MHz

•

•

Infrared on 30-40 kHz

Wi-Fi according to the 802.11 g standard

Additionally the Light-Manager features an integrated webserver, which allows an autarkic and flexible service, as well as a temperature sensor.

The package includes

•

•

Light-Manager Air

Antenna for 433 MHz (pre-installed)

•

•

•

Antenna for 868 MHz (pre- installed)

5V power adaptor with micro USB cable (approx. 1.5 m)

Quickstart guide

Wi-Fi compatibility

The Light-Manager Air uses the 802.11g standard (54 Mbit) with WPA2 encryption on the channels 1-11. Please ensure that your access point is configured accordingly. The network type can be set to any mode including g, for example 802.11 n+g.

3 media

Note: The encryption type must be set to WPA2. The outdated mixed mode

WPA+WPA2 is not supported. This is especially important for FRITZ!Box routers which usually come with mixed mode enabled by default.

Setup with WPS

A comfortable method to connect the Light-Manager to your Wi-Fi network is by using WPS (Wi-Fi Protected Setup). This just requires a push of a button. Please connect the Light-Manager to the AC adaptor included in delivery. Now activate WPS mode at your router. Most devices offer a dedicated button for this purpose. In case of the FRITZ!Box the Wi-Fi button has to be pressed for 5 seconds. Other models require the WPS mode to be enabled in the configuration interface.

Now press the button of the Light-Manager shortly. The LED starts blinking in green.

As soon as the devices have found each other the blinking frequency increases.

Connection establishment can take up to two minutes. When this is done the LED stops blinking and changes its color to dim blue to signal operational readiness. The

Light-Manager is successfully connected to your local Wi-Fi network and the IP address is shown in AirStudio under options -> Light-Manager setup. This setting can be changed in the options, too.

4 media

Setup with Wi-Fi connection

Another possibility to connect the Light-Manager to your Wi-Fi network is by accessing the device directly through its own network. Right after power has been plugged in, the Light-Manager creates its own Wi-Fi network called Light-Manager

Air. You can connect to this network with your smartphone, tablet or PC. There is no password required. Afterwards open a browser and navigate to:

•

192.168.100.115

A website opens up which allows the configuration of the name (SSID) and the passphrase for the Wi-Fi network.

After a click on the OK button the Light-Manager starts connecting to the selcted Wi-

Fi network. During this phase the LED is blinking in green. When this is done the LED stops blinking and changes its color to dim blue to signal operational readiness. Now the Light-Manager is connected to your Wi-Fi network and the IP address is shown in

5 media

AirStudio under options -> Light-Manager setup. This setting can be changed in the options, too.

Possible errors during connection establishment

If the LED flashes in red during connection establishment then there is an error. The number of times it flashes in red gives information about the error source.

•

1x Blinking: the network name (SSID) is wrong

•

2x Blinking: the passphrase is wrong

•

3x Blinking: the access point is set to mixed mode (WPA+WPA2)

• 4x Blinking: the access point is set to WEP or Open

To delete the credentials you have entered, set the device back to factory defaults and start over.

Reset to factory defaults

To reset the Light-Manager to factory defaults please proceed as follows:

•

•

•

Disconnect Light-Manager from power

Keep button at the front of the Light-Manager pressed gently

Connect AC adaptor

•

•

Wait until the LED flashes red

Release the button

6 media

Now the device has been reset and the Wi-Fi connection can be setup again if required. Note: The web interface data will not get cleared by this procedure. If necessary it can be deleted by uploading an empty configuration.

airStudio

The configuration of the Light-Manager is done with the software airStudio which can be found in the download section of www.jbmedia.de

free of charge.

On the left side of the main window there is a table which shows the whole configuration. The right part is split into the Scenes section and the Actions section.

The first section is used to create new scenarios. Here you can select what kind of trigger is used to start the scenario. The selection consists of:

7 media

•

Manual scene: Triggers by a press of a button in the web interface or on an infrared remote control

•

Timer: Triggers at fixed points of time or by astro function

•

Temperature: Triggers by over- or underrun of inside or outside temperature

•

By RF transmitter: Triggers by RF signals e.g. from a push button or motion detector

In the Actions section you can select actions which are performed when a scenario has been triggered. Among others the selection consists of:

•

•

•

Actuator commands

Infrared commands

SONOS commands

•

•

•

Network commands

Long-term and short-term pauses

Marker commands

Manual scene

To create a scenario, which is triggered by a button in the web interface or by a button on an infrared remote control, a click on the Add button is sufficient. Right after the click a new scenario appears in the table on the left side. A scene number is increased automatically. In the right column of the table a short description can be entered. This will be used to display the scenario in the web interface.

8 media

Timer

With the integrated real time clock of the Light-Manager it is possible to trigger scenarios at certain points of times at certain days.

To start this scenario with a Logitech Harmony remote control, please add the device

Light-Manager Air from the Logitech database to your remote control. This will install buttons with the names L001 until L255 on your Harmony. The number behind the letter L corresponds to the scene number configured in AirStudio. Of course the button names appearing on the display of the Harmony can be renamed with the

Logitech software.

If a different remote control other than a Harmony is to be used, then the IR code for each button has to be taught to the remote control manually. For this purpose there is the learn button on the tab:

9 media

The internal clock of the Light-Manager is synchronized with an Internet time server resulting in a very accurate time adjustment at any time.

The option Simulate presence will move points of time in the range of +/- 60 minutes randomly. So for an observer from outside it is not obvious that this is an automated process.

Astro function

Instead of using fixed points of time it is often desired to couple lighting control to dusk or dawn. The Light-Manager offers an extensive astro function for this purpose which calculates the times for civil twilight for each day and each location precisely.

Civil twilight is defined as the point of time where it is not possible anymore to read a newspaper outside in the evening.

10 media

You can define your location in airStudio under Options -> Astro function comfortably by a Google maps application.

Temperature

Scenarios can be triggered when the temperature rises above or falls below a certain level. For this purpose the Light-Manager measures temperature every minute and triggers scenarios if required. This function is useful to control a fan or electric blinds for example.

The hops in the curves are changes from summer to winter time and back. For control purposes the dusk and dawn times for the current day are displayed in the lower right corner of the window. On the left there are two sliders which allow the adjustment of the curves in the range of +/- 6 hours.

Perform actions only by night or by day

Sometimes it is useful to perform certain actions within a scenario only by day or at night. For example you might turn on the living room lights automatically when starting the activity Watch TV on your remote control, but only when it is dark outside. For this purpose the Light-Manager offers the options Only by day and Only

at night in the edit menu and context menu of each action within a scenario. The underlying periods of time are defined by the astro function. At night is defined as the sector between the dusk and dawn curves, by day vice versa.

11 media

Besides the inside temperature, which is measured by the device itself, also the outside temperature can be used as control factor. The source for the outside temperature is a network of weather stations (openweathermap.org), out of which the Light-Manager selects the station which is closest to the location defined in the astro function settings.

Note: The temperature sensor is located on the layer board of the device. Therefore it will heat up slightly after startup, when connecting the Light-Manager to power. This calefaction is compensated automatically. However during the first 30 minutes the device will display a lower temperature than there is actually.

The Light-Manager can measure precise temperatures only if it is not exposed to direct sun light or to another source of heat. Fine tuning can be applied under

Options -> Light-Manager setup -> Extended settings.

12 media

RF Transmitter

A very powerful feature is the ability to trigger scenarios by signals of RF transmitters, e.g. wall switches, motion detectors, magnet switches, brightness detectors or other components. To create such a scenario it is sufficient to send an RF signal with one of these components.

Instantly the corresponding RF code will be displayed in AirStudio. This scenario will be triggered each time this code has been received. If it is received several times in a row, the Light-Manager waits three seconds before it triggers the scenario again. This prevents unintended multiple execution of scenarios.

Front button

The button of the Light-Manager is an additional convenient input source to trigger two scenarios of your choice, depending if the button has been pressed short or long

(> 2 sec.). The selection is done by the menu items Button short and Button long from the context and edit menu. This function is suitable for turning off the whole lighting when going to bed for example.

13 media

E-mail notification

The Light-Manager allows getting a notification by e-mail when a scenario has been executed. This is especially suitable for scenarios which are triggered by sensors. So you could get an e-mail as soon as a window or a door has been opened or motion has been detected. If you want to go a step further you can also enter the address of an SMS provider. Then you will get an SMS notification on your phone within a few seconds worldwide. This can be very useful for alarm events.

It is possible to configure two different e-mail addresses, one for standard notifications and one for alarm notifications with higher priority. These addresses can be entered under Options -> Light-

Manager setup -> E-mail

setup.

You can activate the notification feature by selecting a scenario in the table, and then from the edit or context menu (right click) select Send e-mail

(default) or Send e-mail (alarm). Both options can be enabled for the same scenario if desired. So one could send an e-mail to two recipients or send one e-mail and one

SMS.

14 media

Adding actuators

Before you can select an actuator from the drop down list it has to be added to the actuator administration. To get there click on the little button next the drop down list.

The actuator administration will show up in a new window.

In the upper part of the window all actuators and zones are listed which have been added already. Zones make it possible to group actuators into logical units, like rooms or areas of your home. Below the table there are tabs for each supported system. On these you can configure each actuator. Please note that some tabs are meant for more than one brand. So the InterTechno – Trust tab is also made for brands like

COCO, KlikAanKlikUit, Trust, HomeEasy UK, Elro, Chacon, Nexa and more. The INSTA tab is for Gira, Berker, Jung and Busch-Jäger (433.42 MHz).

After an actuator has been added, it can be named by clicking on it. A right click opens a context menu with more menu items. There you find options to check in and out the actuator from the Light-Manager.

Note: If you have an RF remote control for your actuators, it is sufficient to press a button on the remote control to add the corresponding actuator automatically. The

Light-Manager processes the received signals and calculates the parameters like housecode and channel for you. This method is not yet supported for all systems.

15 media

16 media

Markers

Markers are a powerful tool for advanced programming technics. Markers are variables which can have the values 1 (ON) and 0 (OFF) only. The value of each marker can be altered by actions within scenarios. This makes it possible to visualize certain information in the marker section of the web interface.

So you could visualize if a window is open or if the alarm system is armed. Also marker states can be tied to scenarios in form of conditions, so that a scenario is executed only if one or more markers have a defined state. This is done by selecting a scenario in the table and opening the

Marker Selection window from the edit- or context menu. In this window the desired states of the markers can be configured which are required to make this scenario executable. (All markers are in an AND-relation.) If these states are not met the scenario will not be executed.

This allows the creation of so called IF-THEN statements. Using markers makes it possible to create complex courses of actions with simple programming tasks.

17 media

Transferring the configuration

When configuration is completed it has to be transferred to the Light-Manager. This is done with the Transfer button.

Finally the Light-Manager is ready for action. A click on the Browser button opens up the web interface in the default browser instantly. There it can be verified and used instantly.

Web Interface

The web interface is the central operating interface for the Light-Manager. It works on all devices which features a web browser, even on a smart watch (available for

Android Wear and Apple

Watch).

The head line shows the name of the configuration, also the inside- and outside-

18 media

temperature is shown as well as the current time, date and wind speed. Below the head line there are several areas which can be opened and closed individually. The first area includes all scenes defined in airStudio. The adjacent areas are the zones, defined in the actuator administration of airStudio. Each zone lists all actuators which are part of the zone, and shows proper control elements for each of them. The last area is the marker section, which displays the state of each marker. By touching a marker its state can be toggled.

A click on the room temperature opens up the weather chart which shows the course of weather data for the last 48 hours. The state of the web interface is saved automatically and restored on startup.

Under Android and iOS the web interface can be turned into a web app. That means that the application will no longer be displayed as a web page in the browser. Instead it will have its own icon on the home screen and will be opened full screen as a standalone application, just like other apps on the phone or tablet. For this purpose it is sufficient to select Add to home screen from the browser’s menu.

If you have configured login data for the web interface then this data can be used in the web app,

19 media too, without the need to enter it manually each time.

Just open the interface in the browser by a link which has this format: http://login:password@IP-address

(e.g. http://admin:[email protected]

) iOS might bring up a warning message, which can be ignored. Afterwards select Add to home screen as described before. From now on the web app will use this data automatically.

20 media

Access through the Internet

Access to the web interface is not limited to your home network. Instead you can access the interface from any point of the world where you have Internet connection.

So you could turn on your home coffee machine from on the way already for example.

For this purpose it is necessary to open port 80 in the router and forward it to the IP address of the Light-Manager. For testing you can disable Wi-Fi in your phone and enter the external IP address of your router (given from your Internet provider) in the browser. The web interface should open up immediately if you have mobile data.

Now the web interface is reachable from on the go.

Most DSL connections use dynamic IP addresses. This means that the IP address changes once within 24 hours. To keep access to your web interface the Light-

Manager offers DynDNS service free of charge. This has just to be enabled under

options Light-Manager

setup Extended settings.

From now on the web interface is always available under the shown URL. If a different port than port 80 is used, the port number has to be appended with a colon. So the final URL might be:

21 media http://0123456789ab.dns.jbmedia.de:100

As this URL is not easy to remember, it is useful to send the URL to yourself by e-mail.

By double click it will be opened in the default browser automatically. This URL can also be used for other devices in your household, which you might want to access online. By using different ports an unlimited number of devices like IP cams can be connected this way.

Modification of the Web Interface

The template used for creation of the web interface is stored in the subfolder /html of the airStudio installation. Smaller changes like colors or font sizes can be done directly in the CSS file in this folder. When clicking the transfer button AirStudio loads this template and generates your individual web interface. This is stored in the folder

%appdata%/AirStudio/html_temp before it is compressed and uploaded to the webserver of the Light-Manager finally. In contrast to the /html folder the

/temp_temp folder contains all your personal scenarios and actuators.

Larger modifications require changes of the file index.htm and possibly of the file lightman.js, which contains Javascript. We recommend this procedure to skilled users with HTML, CSS and Javascript knowledge only.

22 media

Technical data

Operating voltage: 5 Volts

Power consumption: ca. 0.9 Watts

Dimensions (W x H X D): ca. 6 x 6 x 2 cm

Wi-Fi types: Infrastructure and Virtual Access Point

Wi-Fi standards: 802.11 g with WPS function

Wi-Fi channels: 1 – 11

Wi-Fi encryption: WPA2

Radio transmission frequencies: 433.42, 433.92 and 868.35 MHz

Radio reception frequencies: 433.42, 433.92 and 868.35 MHz

Infrared transmission frequency: 38 kHz

Infrared reception frequencies: 30-40 kHz

Memory capacity: 2 Megabyte flash available memory for web interface

Supported operating systems of AirStudio software:

Windows 2000, Windows XP, Windows Vista, Windows 7 and 8

23 media

media

jb media Dreherstrasse 24 42899 Remscheid Germany