IKEA | DW60 | User's Manual | IKEA DW60 User's Manual

RENLIG
DW60
GB
ENGLISH
4
ENGLISH
4
Contents
Safety information
Product description
Control panel
Washing programmes
Use of the appliance
Setting the water softener
Use of dishwasher salt
Use of rinse aid
Loading cutlery and dishes
Use of detergent
4
6
7
9
10
10
11
12
12
14
Setting and starting a washing programme
Care and cleaning
What to do if…
Technical data
Installation
Water connection
Electrical connection
Environment concerns
IKEA GUARANTEE
15
16
17
19
19
20
21
21
21
Subject to change without notice
Safety information
For your safety and correct operation of
the appliance, read this manual carefully
before installation and use. Always keep these
instructions with the appliance even if you
move or sell it. Users must fully know the operation and safety features of the appliance.
Correct use
• The appliance is designed exclusively for
domestic use.
• Only use the appliance to clean household
utensils that are applicable for dishwashers.
• Do not put solvents in the appliance. Risk of
explosion.
• Put the knives and all items with sharp points
in the cutlery basket with their points down.
If not, put in a horizontal position in the upper basket.
• Use only branded products for dishwashers
(detergent, salt, rinse aid).
• If you open the door while the appliance is
in operation, hot steam can escape. Risk of
skin burns.
• Do not remove dishes from the dishwasher
before the end of the washing programme.
• When the washing programme is completed, disconnect the mains plug from the
mains socket and close the water tap.
• Only an authorised service engineer can repair this appliance. Use only original spare
parts.
• Do not do repairs yourself to prevent injury
and damage to the appliance. Always contact your local After Sales Service.
General safety
• Persons (including children) with reduced
physical sensory, mental capabilities or lack
of experience and knowledge must not use
the appliance. They must have supervision
or instruction for the operation of the appliance by a person responsible for their safety.
• Obey the safety instructions from the manufacturer of the dishwasher detergent to
prevent burns to eyes, mouth and throat.
• Do not drink the water from the dishwasher.
Detergent residues can stay in your appliance.
• Always close the door when you do not use
the appliance to prevent injury and not to
stumble over the open door.
• Do not sit or stand on the open door.
Child safety
• Only adults can use this appliance. Children
must get supervision to make sure that they
do not play with the appliance.
• Keep all the packaging away from children.
There is a risk of suffocation.
• Keep all detergents in a safe area. Do not
let children touch the detergents.
• Keep children away from the appliance
when the door is open.
ENGLISH
Installation
• Make sure that the appliance is not damaged because of transport. Do not connect
a damaged appliance. If necessary, contact
the supplier.
• Remove all packaging before first use.
• A qualified and competent person must do
the electrical installation.
• A qualified and competent person must do
the plumbing installation.
• Do not change the specifications or modify
this product. Risk of injury and damage to
the appliance.
• Do not use the appliance:
– if the mains cable or water hoses are
damaged,
– if the control panel, worktop or plinth area
are damaged, that you can get access to
the inner side of the appliance.
If you have any doubts, please contact your
After Sales Service. Refer to the list of the
After Sales Services at the end of user manual.
5
• Do not drill into the sides of the appliance to
prevent damage to hydraulic and electrical
components.
Warning! Carefully obey the instructions
for electrical and water connections.
ENGLISH
6
Product description
1
2
9
3
8
4
5
7
6
1
2
3
4
5
Upper basket
Water hardness dial
Salt container
Detergent dispenser
Rinse aid dispenser
6
7
8
9
Rating plate
Filters
Lower spray arm
Upper spray arm
ENGLISH
7
Control panel
5
1
2
A
1
2
3
4
5
4
3
B
On/off button
Half-load button
Programme selection/cancel button (SELECT/CANCEL)
Indicator lights
Programme indicator lights
Indicator lights
The indicator light comes on when the washing
programme is completed. Auxiliary functions:
• Level of the water softener.
• Activation/deactivation the audible signals.
• An alarm if the appliance has a malfunction.
1)
1)
The indicator light comes on when it is necessary to fill the rinse aid. Refer to the chapter
'Use of rinse aid'.
The indicator light comes on when it is necessary to fill the salt container. Refer to the chapter 'Use of dishwasher salt'.
The salt indicator light can stay on for some
hours, but it does not have an unwanted effect
on the operation of the appliance.
1) The indicator light is off while a washing programme operates.
ENGLISH
Programme selection/cancel button
Use the programme selection/cancel button
for these operations:
• To set the washing programme. Refer to the
chapter 'Setting and starting a washing programme'.
• To set the water softener. Refer to the chapter 'Setting the water softener'.
• To deactivate/activate the audible signals.
Refer to the section 'Audible signals'.
• To cancel a washing programme in progress. Refer to the chapter 'Setting and starting a washing programme'.
Half-load button
The half-load option is not available for all
washing programmes. Refer to the chapter
'Washing programmes'.
• Load dishes in the upper and lower basket.
• Decrease the detergent dosage when you
use the half-load option.
• Press the half-load button to set the option.
– The half-load indicator light comes on,
when the half-load option is selectable.
With the half-load button pressed the
time duration and the consumption of water and energy are reduced.
Setting mode
The appliance is in setting mode when all the
programme indicator lights are off and the end
indicator light flashes.
The appliance must be in setting mode for
these operations:
– To set a washing programme.
– To set the water softener level.
– To deactivate/activate the audible signals.
If a programme indicator light is on, cancel the
programme to go back to the setting mode.
Refer to the chapter "Setting and starting a
washing programme".
Programme indicator lights A and B
Apart the selection of the corresponding washing programme, these lights have an auxiliary
functions:
8
• The adjustment of the water softener level.
• Deactivation/activation of the audible signals.
Audible signals
You can hear an audible signal:
• At the end of the washing programme.
• When the appliance has a malfunction.
The activation of the audible signals is set at
the factory.
Do these steps to deactivate the audible signals:
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press and hold the programme selection/
cancel button until programme indicator
light A flashes and programme indicator
light B comes on.
4. Press the programme selection/cancel
button again.
– Programme indicator light A comes on.
– Programme indicator light B starts to
flash.
5. Wait until programme indicator light A
goes off.
– Programme indicator light B continues to
flash.
– The end indicator light comes on.
The audible signals are activated.
6. Press the programme selection/cancel
button again.
– The end indicator light goes off.
The audible signals are deactivated.
7. Switch off the appliance to save the operation.
Do these steps to activate the audible signals:
1. Do the above procedure until the end indicator light comes on.
ENGLISH
9
Washing programmes
Washing programmes
Programme
Intensive
Normal
1)
Quick
Eco 2)
Hold
Rinse &
Degree of
Type of load
soil
Programme description
Half-load option
Prewash
Main wash up to 70°C
2 intermediate rinses
Final rinse
Drying
yes
Heavy soil
Crockery,
cutlery, pots
and pans
Prewash
Main wash up to 65°C
2 intermediate rinses
Final rinse
Drying
yes
Normal soil
Crockery,
cutlery, pots
and pans
Normal or
light soil
Crockery
and cutlery
Main wash up to 60°C
Final rinse
no
Normal soil
Prewash
Main wash up to 50°C
1 intermediate rinse
Final rinse
Drying
yes
Crockery
and cutlery
Any
Partial load
(to be completed later
in the day)
1 cold rinse (to prevent food
scraps to bond).
Detergent is not necessary
with this programme.
no
1) This is the perfect daily programme to clean a not fully load. Ideal for a family of 4 persons who only want
to load breakfast and dinner crockery and cutlery.
2) Test programme for test institutes. This is the economy washing programme. Please refer to separate leaflet
supplied, for test data. Available only in 3 languages (English, French, German) just for test institutes
purpose.
Consumption values (for full washing cycle)
Programme
1)
Programme duration Energy consumption Water consumption
(minutes)
(kWh)
(litres)
120-130
1,8-2,0
22-24
105-115
1,5-1,7
23-25
30
0,9
9
130-140
1,0-1,2
14-16
ENGLISH
10
Programme
Programme duration Energy consumption Water consumption
(minutes)
(kWh)
(litres)
12
0,1
5
1) The duration of this washing programme is prefixed (longer) than the others due to a prolonged drying
and washing phases.
The pressure and temperature of the water, the variations of power supply and
the quantity of dishes can change these values.
Use of the appliance
Refer to the following instructions for each step
of procedure:
1. Make a check if the water softener level is
correct for the water hardness in your area.
If necessary set the water softener.
2. Fill the salt container with dishwasher salt.
3. Fill the rinse aid dispenser with rinse aid.
4. Load cutlery and dishes into the dishwasher.
5. Set the correct washing programme for the
type of load and soil.
6. Fill the detergent dispenser with the correct
quantity of detergent.
7. Start the washing programme.
If you use detergent tablets, refer to the
chapter 'Use of detergent'.
Setting the water softener
The water softener removes minerals and salts
from the water supply. Minerals and salts can
have bad effect on the operation of the appliance.
Water hardness is measured in equivalent
scales:
• German degrees (dH°).
• French degrees (°TH).
• mmol/l (millimol per litre - international unit
for the hardness of water).
• Clarke.
Adjust the water softener to the water hardness in your area. If necessary, contact your
local water authority.
Water hardness
Water hardness setting
°dH
°TH
mmol/l
Clarke
manually
electronically
51 - 70
91 - 125
9,1 - 12,5
64 - 88
2
10
43 - 50
76 - 90
7,6 - 9,0
53 - 63
2
9
37 - 42
65 - 75
6,5 - 7,5
46 - 52
2
8
29 - 36
51 - 64
5,1 - 6,4
36 - 45
2
7
23 - 28
40 - 50
4,0 - 5,0
28 - 35
2
6
19 - 22
33 - 39
3,3 - 3,9
23 - 27
2
5
15 - 18
26 - 32
2,6 - 3,2
18 - 22
1
4
11 - 14
19 - 25
1,9 - 2,5
13 - 17
1
3
ENGLISH
11
Water hardness
Water hardness setting
°dH
°TH
mmol/l
Clarke
manually
electronically
4 - 10
7 - 18
0,7 - 1,8
5 - 12
1
2
<4
<7
< 0,7
<5
11)
11)
1) No use of salt required.
You must set the water softener manually
and electronically.
Manual adjustment
The appliance is set at the factory at position
2.
1
2
Set switch to position
1 or 2.
Electronic adjustment
The water softener is set at the factory at
level 5.
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press and hold the programme selection/
cancel button.
4. Release the programme selection/cancel
button when programme indicator light A
starts to flash and programme indicator
light B comes on.
5. Wait until programme indicator light B
goes off.
– Programme indicator light A starts to
flash.
– The end indicator light starts to flash.
6. Press the programme selection/cancel
button one time.
– Programme indicator light A starts to
flash.
– The setting function of the water softener
is activated.
– The end indicator light flashes to show
the level of the water softener.
Example: 5 flashes, pause, 5 flashes,
pause, etc... = level 5.
7. Press the programme selection/cancel
button one time to increase the water softener level by one step.
8. Press the on/off button to save the operation.
Use of dishwasher salt
Caution! Only use dishwashers salt.
Types of salt that are not applicable for
dishwashers cause damage to the water
softener.
1
2
ENGLISH
12
3
4
5
6
Fill the salt container
with 1 litre of water
(only the first operation).
Fill the salt container
with 1,5-2,0 kg of
salt. Use the salt funnel supplied.
Make sure that there
is no grain of salt outer of the salt compartment.
It is normal that water overflows from the
salt container when you fill it with salt.
Use of rinse aid
Caution! Only use branded rinse aid for
dishwashers.
Do these steps to fill the rinse aid dispenser:
1
2
Caution! Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent).
There is a risk of damage to the appliance.
Adjusting the dosage of rinse aid
The rinse aid dial is
set at the factory at
position 3.
To increase or decrease the dosage
refer to 'What to do
if...'
3
4
M
+
AX
-
Loading cutlery and dishes
Helpful hints and tips
Caution! Only use the appliance for
household utensils that are applicable for
dishwashers.
ENGLISH
Do not use the appliance to clean objects that
can absorb water (sponges, household cloths,
etc.).
• Before you load cutlery and dishes, do these
steps:
– Remove all food remainings and debris.
– Make burnt, remaining food in pans soft.
• While you load cutlery and dishes, do these
steps:
– Load hollow items (e.g. cups, glasses and
pans) with the opening down.
– Make sure that water does not collect in
the container or in a deep base.
– Make sure that cutlery and dishes do not
lie inside one another.
– Make sure that cutlery and dishes do not
cover other cutlery and dishes.
– Make sure that glasses do not touch other
glasses.
– Put small objects in the cutlery basket.
• Plastic items and pans with non-stick coatings can keep water droplets. Plastic items
do not dry as well as porcelain and steel
items.
• Put light items in the upper basket. Make
sure that the items do not move.
Caution! Make sure that the spray arms
can move freely before you start a
washing programme.
Warning! Always close the door after
you load or unload the appliance. An
open door can be dangerous.
13
Use the cutlery grid. If the dimensions of
the cutlery prevent use of the cutlery grid,
remove it.
Arrange the items to let water touch all surfaces (left). For longer items fold the cup
racks up (right).
Put plates in the rear part of the upper
basket. Tilt them forward.
Adjustment of the height of the upper basket
If you put large plates in the lower basket, first
move the upper basket to a upper position.
Warning! Adjust the height before you
load the upper basket.
Arrange
service
dishes and large lids
around the edge of
the lower basket.
Maximum height of the dishes in :
• Upper basket.
– Upper position: 20 cm.
– Lower position: 24 cm.
• Lower basket.
– Upper position: 31 cm.
– Lower position: 27 cm.
ENGLISH
14
A
A
Do these steps to move the upper basket to the
upper or lower position:
1. Move the front runner stops (A) out.
2. Pull the basket out.
3. Put the basket in the upper or lower position.
4. Replace the front runner stops (A) in their
initial position.
Caution! If the basket is in the upper
position, do not put cups on the cup racks.
Use of detergent
Only use detergents (powder, liquid or
tablet) that are applicable for dishwash-
4
3
ers.
Follow the data on the packaging:
• Dosage recommended by the manufacturer.
• Storage recommendations.
B
A
Do not use more than the correct quantity of
detergent to save an environment.
1
2
Fill the detergent dis- If you use a washing
penser (A) with de- programme
with
tergent.
prewash phase, put
more detergent in
the prewash detergent compartment
(B).
5
6
A
Use of detergent tablets
Put the detergent tablet in the detergent dispenser (A).
Detergent tablets contain:
• detergent
• rinse aid
• other cleaning agents.
Do these steps to use detergent tablets:
ENGLISH
15
1. Make sure that the detergent tablets are
applicable for your water hardness. Refer
to the instructions from the manufacturer.
2. Set the lowest levels of water hardness and
rinse aid dosage.
2. Set the water softener to the highest level.
3. Do a washing programme without dishes.
4. Adjust the water softener. Refer to the
chapter 'Setting the water softener'.
5. Adjust the rinse aid dosage.
It is not necessary to fill the salt container
and the rinse aid dispenser.
Different brands of detergent dissolve in
different times. Some detergent tablets
do not have the best cleaning results during
short washing programmes. Use long washing
programmes when you use detergent tablets
to fully remove the detergent.
Do these steps when the drying results are
not satisfactory:
1. Fill the rinse aid dispenser with rinse aid.
2. Set the rinse aid dosage to position 2.
Do these steps to use the detergent powder
again:
1. Fill the salt container and the rinse aid dispenser.
Setting and starting a washing programme
Set the washing programme with the
door ajar. The washing programme only
starts after you close the door. Until then it is
possible to modify the settings.
Do these steps to set and start a washing programme:
1. Switch on the appliance.
2. Make sure that the appliance is in setting
mode.
3. Press the programme selection/cancel
button again and again to set the washing
programme. Refer to the chapter 'Washing
programmes'.
– The programme indicator light comes
on.
4. Close the door.
– The washing programme starts automatically.
When the washing programme operates,
you cannot change the programme. Cancel the washing programme.
Warning! Only interrupt or cancel a
washing programme if necessary.
Caution! Open the door carefully. Hot
steam can come free.
Cancelling a washing programme
1. Press and hold the programme selection/
cancel button for approximately 3 seconds.
– The programme indicator light goes off.
– The end indicator light starts to flash.
2. Release the programme selection/cancel
button to cancel the washing programme.
At this time you can do these steps:
1. Switch off the appliance.
2. Set a new washing programme.
Fill the detergent dispenser with detergent before you set a new washing programme.
Interrupting a washing programme
Open the door.
• The programme stops.
Close the door.
• The programme continues from the point of
interruption.
End of the washing programme
Switch off the appliance in these conditions:
• The appliance stops automatically.
• The audible signals for the end of the programme operate.
1. Open the door.
– The end indicator light comes on.
– The programme indicator light stays on.
2. Press the on/off button.
ENGLISH
16
3. For better drying results, keep the door
ajar for some minutes before you remove
the dishes.
Let the dishes cool down before you remove
them from the appliance. Hot dishes are easily
damaged.
• There can be water on the sides and door
of the appliance. Stainless steel becomes
cool more quickly than the dishes.
Removing the load
• First remove items from the lower basket,
then from the upper basket.
Care and cleaning
Warning! Switch the appliance off before
you clean the filters.
6
5
Cleaning the filters
Important! Do not use the appliance without
the filters. Make sure that the installation of the
filters is correct. Incorrect installation will cause
unsatisfactory washing results and damage to
the appliance.
1
2
B
A
2
Put the filter system in
position. To lock the
filter system, turn the
handle clockwise until it locks in position.
Important! Do not remove the spray arms.
A
Fully clean the filters
A, B and C below running water.
4
2
1
1
Put the flat filter A in
the bottom of the appliance. Install the
flat filter correctly under the two guides D.
C
3
D
A
To remove filters B Remove the flat filter
and C, turn the han- A from the bottom of
dle approximately the appliance.
1/4 anticlockwise.
If the holes in the spray arms become clogged,
remove remaining parts of soil with a cocktail
stick.
Long periods of non-operation
Do these steps when you do not use the appliance for a long period:
1. Disconnect the mains plug from the mains
socket.
2. Close the water tap.
3. Keep the door open to prevent unpleasant
smells.
4. Keep the inner side of the appliance clean
(filters especially).
External cleaning
Clean the external surfaces of the appliance
and control panel with a damp soft cloth. Only
use neutral detergents. Do not use abrasive
products, scouring pads or solvents (acetone,
trichloroethylene etc...).
ENGLISH
17
Frost precautions
Caution! Do not install the appliance
where the temperature is below 0 °C. The
manufacturer is not responsible for damage
because of frost.
If not possible, empty the appliance and close
the door. Disconnect the water inlet hose and
remove water from the water inlet hose.
What to do if…
The appliance does not start or stops during operation.
If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution
to the problem yourself, contact your dealer or the After Sales Service.
Problem
Possible cause
Solution
• Continuous flash
of the light of the
running
programme.
• Intermittent audible signal.
• 1 flash of the end
indicator light.
Malfunction:
The
dishwasher
does not fill with water.
The water tap is blocked or furred Clean the water tap.
with limescale.
• Continuous flash
of the light of the
running
programme.
• Intermittent audible signal.
• 2 flashes of the
end
indicator
light.
Malfunction:
The dishwasher will
not drain.
There is a blockage in the sink spi- Clean the sink spigot.
got.
The water tap is closed.
Open the water tap.
The filter in the water inlet hose is Clean the filter.
blocked.
The connection of the water inlet Make sure that the connection is
hose is not correct. The hose can be correct.
kinked or squashed.
The connection of the water drain Make sure that the connection is
hose is not correct. The hose can be correct.
kinked or squashed.
ENGLISH
Problem
18
Possible cause
Solution
• Continuous flash Close the water tap and Contact your local After Sales Service.
of the light of the
running
programme.
• Intermittent audible signal.
• 3 flashes of the
end
indicator
light.
Malfunction:
The anti-flood device operates.
Malfunction:
The appliance door is not closed. Close the door.
The
programme Mains plug is not connected in.
Put in the mains.
does not start.
The fuse has blown out in the Replace the fuse.
household fuse box.
After the check, switch on the appliance. The programme continues from the point of interruption. If the malfunction shows again, contact your After Sales Service.
When the cleaning results are not satisfactory:
Problem
The dishes are
not clean
Possible cause
Solution
The selected washing programme is Set different washing programme.
not applicable for the type of load
and soil.
The baskets are loaded incorrectly so Load the baskets correctly.
that water cannot reach all surfaces.
Spray arms do not turn freely because Make sure that the cutlery and dishes
of incorrect arrangement of the load. do not block the spray arms.
The filters are dirty or not correctly in- Make sure that the filters are clean
stalled.
and installed correctly.
The quantity of detergent is too little Make sure that the quantity of deteror missing.
gent in detergent dispenser is correct.
Limescales
The salt container is empty.
Fill the salt container with salt.
particles on the
The water softener is adjusted on a Set the water softener.
dishes
wrong level.
The salt container cap is not closed Make sure that the salt container is
correctly.
closed correctly.
The dishes are
wet and dull
No rinse aid has been used.
Set the rinse aid dosage.
The rinse aid dispenser is empty.
Fill the rinse aid dispenser.
ENGLISH
19
Problem
Possible cause
There are
streaks, milky
spots or a bluish coating on
glasses and
dishes
Solution
Wrong dosage of rinse aid.
Decrease the rinse aid dosage.
Dry water drop Wrong dosage of rinse aid.
signs on
The detergent can be the cause.
glasses and
dishes
Increase rinse aid dosage.
Use different type of detergent.
Technical data
Dimensions
Width (cm)
59,6
Height (cm)
81,8-87,8
Depth (cm)
Water supply
pressure1)
Minimum
Maximum
Capacity (place settings)
12
Energy class
A
Washing class
A
Drying class
A
Noise (dB(A))
49
Average annual energy consumption (kWh) 2)
231
Average annual water consumption (litres)2)
3520
55,5
0,5 bar (0,05 MPa)
8 bar (0,8 MPa)
1) If the pressure in your area is lower or higher, please contact your After Sales Service.
2) The data is based on the washing programme for test institutes assuming 220 cycles per a year.
Information on the electrical connection, voltage and overall power is given on the rating
plate on the inner edge of the dishwasher door.
Installation
Caution! Refer to the assembly
instructions, in order to proceed with the
installation.
Warning! Make sure that mains plug is
disconnected from the mains socket during
installation.
Place the appliance on the floor and install it
under a counter (kitchen worktop or sink).
ENGLISH
If a repair is necessary, the appliance must be
easily accessible for the engineer.
Put the appliance adjacent to a water tap and
a drain.
20
For the venting of the dishwasher only water
fill, water drain and power supply cable openings are necessary.
Water connection
This appliance has a special inlet hose for
water stop later defined as aqualock.
Water inlet hose
Connected the appliance to a hot (max. 60°)
or cold water supply.
If the hot water comes from alternative sources
of energy that are more environmentally
friendly (e.g. solar or photovoltaic panels and
aeolian), use a hot water supply to decrease
energy consumption.
Connect the inlet hose to a water tap with an
external thread of 3/4".
Caution! Do not use connection hoses
from an old appliance.
Caution! If you connect the appliance to
new pipes or pipes that are not used for
a long time, we recommend to run the water
for some minutes before you connect the inlet
hose.
Aqualock inlet hose
The inlet hose is a high pressure resistant. It can
hold pressure at maximum 6 MPa. From external the inlet hose has a sheathing against
eventual damages. If the inner hose breaks,
the water that is in the hose will became dark.
You can see it across the special transparent
sheathing. Turn off the water tap immediately
and contact the After Sales Service.
A
B
The aqualock inlet
hose is installed with
a safety device to
prevent accidental
loosening. To disconnect the hose:
• Press the lever ( B ).
• Turn the retaining
ring ( A ) anticlockwise.
Turn the inlet hose to
the left or the right to
suit the installation.
Tight the locknut correctly to prevent water leaks.
If you use a inlet
hose extension
the total reached
length must be no
longer than 4 metres.
Drain hose
A
If you connect the
water drain hose to a
water trap under the
sink, remove the
plastic
membrane
(A). If you do not remove the membrane,
remaining food can
cause a blockage in
the drain hose spigot.
Caution! Make
sure that the
water couplings are
tight to prevent water leakage.
ENGLISH
21
Electrical connection
Warning! The manufacturer is not
responsible if you do not follow these
safety precautions.
Ground the appliance according to safety precautions.
Make sure that the rated voltage and type of
power on the rating plate agree with the voltage and the power of the local power supply.
Always use a correctly installed shockproof
socket.
Do not use multi-way plugs, connectors and
extension cables. There is a risk of fire.
Do not replace the mains cable yourself. Contact the After Sales Service.
Make sure that the mains plug is accessible
after installation.
Do not pull the mains cable to disconnect the
appliance. Always pull the mains plug.
Warning! The appliance is supplied with
a 13 amp plug attached. Use a 13 amp
ASTA approved (BS 1362) fuse if it is necessary
to change the fuse in the plug supplied.
A cut off plug inserted into a 13 amp socket is
a serious safety danger. Make sure that it is
disposed of safely.
This appliance complies with the E.E.C. Directives.
Environment concerns
The symbol
on the product or on its
packaging indicates that this product may not
be treated as household waste. Instead it
should be taken to the appropriate collection
point for the recycling of electrical and
electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent
potential negative consequences for the
environment and human health, which could
otherwise be caused by inappropriate waste
handling of this product. For more detailed
information about recycling of this product,
please contact your local council, your
household waste disposal service or the shop
where you purchased the product.
Before disposal of appliance
Warning! Do these steps to dispose the
appliance:
• Pull the mains plug out of the mains socket.
• Cut off the mains cable and discard it.
• Discard the door catch. This prevents the
children to close themselves inside the appliance. Risk of suffocation.
Packaging materials
The materials with the symbol
are recyclable. Dispose the packaging in a suitable collection containers to recycle it.
IKEA GUARANTEE
How long is the IKEA guarantee valid?
This guarantee is valid for five (5) years from
the original date of purchase of Your appliance at IKEA, unless the appliance is named
LAGAN in which case two (2) years of guarantee apply. The original sales receipt is re-
ENGLISH
quired as proof of purchase. If service work is
carried out under guarantee, this will not extend the guarantee period for the appliance,
Which appliances are not covered by the
IKEA five (5) years guarantee?
The range of appliances named LAGAN and
all appliances purchased in IKEA before 1st of
August 2007.
Who will execute the service?
IKEA service provider will provide the service
through its own service operations or authorized service partner network.
What does this guarantee cover?
The guarantee covers faults of the appliance,
which have been caused by faulty construction
or material faults from the date of purchase
from IKEA. This guarantee applies to domestic
use only. The exceptions are specified under
the headline “What is not covered under this
guarantee?” Within the guarantee period, the
costs to remedy the fault e.g. repairs, parts, labour and travel will be covered, provided that
the appliance is accessible for repair without
special expenditure. On these conditions the
EU guidelines (Nr. 99/44/EG) and the respective local regulations are applicable. Replaced
parts become the property of IKEA.
What will IKEA do to correct the problem?
IKEA appointed service provider will examine
the product and decide, at its sole discretion,
if it is covered under this guarantee. If considered covered, IKEA service provider or its authorized service partner through its own service operations, will then, at its sole discretion,
either repair the defective product or replace
it with the same or a comparable product.
What is not covered under this guarantee?
• Normal wear and tear.
• Deliberate or negligent damage, damage
caused by failure to observe operating instructions, incorrect installation or by connection to the wrong voltage, damage
caused by chemical or electro-chemical reaction, rust, corrosion or water damage including but not limited to damage caused by
excessive lime in the water supply, damage
caused by abnormal environmental conditions.
• Consumable parts including batteries and
lamps.
22
• Non-functional and decorative parts which
do not affect normal use of the appliance,
including any scratches and possible color
differences.
• Accidental damage caused by foreign objects or substances and cleaning or unblocking of filters, drainage systems or soap
drawers.
• Damage to the following parts: ceramic
glass, accessories, crockery and cutlery baskets, feed and drainage pipes, seals, lamps
and lamp covers, screens, knobs, casings
and parts of casings. Unless such damages
can be proved to have been caused by production faults.
• Cases where no fault could be found during
a technician’s visit.
• Repairs not carried out by our appointed
service providers and/or an authorized
service contractual partner or where nonoriginal parts have been used.
• Repairs caused by installation which is faulty
or not according to specification.
• The use of the appliance in a non-domestic
environment i.e. professional use.
• Transportation damages.
• Cost for carrying out the initial installation of
the IKEA appliance, unless it is due to a repair or a replacement for faulty parts.
This restriction does not apply to fault-free
work carried out by a qualified specialist using
our original parts in order to adapt the appliance to the technical safety specifications of
another EU country.
How country law applies
The IKEA guarantee gives You specific legal
rights, which covers or exceed local demands.
However these conditions do not limit in any
way consumer rights described in the local
legislation
Area of validity
For appliances which are purchased in one EU
country and taken to another EU country, the
services will be provided in the framework of
the guarantee conditions normal in the new
country. An obligation to carry out services in
the framework of the guarantee exists only if
the appliance complies and is installed in accordance with:
ENGLISH
• the technical specifications of the country in
which the guarantee claim is made;
• the Assembly Instructions and User Manual
Safety Information;
The dedicated SERVICE for IKEA appliances
Please do not hesitate to contact IKEA appointed SERVICE to:
• make a service request under this guarantee;
• ask for clarification on installation of the
IKEA appliance in the dedicated IKEA kitchen furniture. The service won’t provide clarifications related to:
– the overall IKEA kitchen installation;
– connections to electricity (if machine
comes without plug and cable), to water
and to gas since they have to be executed
by an authorized service engineer.
• ask for clarification on user manual contents
and specifications of the IKEA appliance.
To ensure that we provide you with the best
assistance, please read carefully the Assembly
Instructions and/or the User Manual section of
this booklet before contacting us.
How to reach us if You need our service
Please refer to the last page of this manual for
the full list of IKEA appointed Service Providers
and relative national phone numbers.
Important! In order to provide You with a
quicker service, we recommend that You use
the specific phone numbers listed at the end of
this manual. Always refer to the numbers listed
in the booklet of the specific appliance You
need an assistance for. Before calling us,
assure that You have to hand the IKEA article
number (8 digit code) for the appliance of
which you need our assistance.
Important! SAVE THE SALES RECEIPT! It is
Your proof of purchase and required for the
guarantee to apply. Note that the receipt
reports also the IKEA article name and number
23
(8 digit code) for each of the appliances you
have purchased.
Do You need extra help?
For any additional question, not listed in the
above paragraph “The dedicated SERVICE for
IKEA appliances”, please do not use the specific phone numbers in the last page of this
booklet, but contact our nearest IKEA store
Call Center. We recommend that you carefully
read the appliance documentation before
contacting us.
24
France
0170 36 02 05
Germany
01803-334532 (0,09€/Min. aus dem Festnetz der DTAG;
Mobilfunkpreise abweichend)
Italy
02 00620818
Spain
91 1875537
UK
020 3347 0044
Holland
0172 468 568
Sweden
0770 330015
Norway
815 22052
Denmark
07922 1368
Belgium
070 246016
Austria
081 300486 zum Ortstarif
Switzerland
031 5500 324
Portugal
211 557 985
Czech Republic
246 019721
Poland
012 297 8787
Russia
0495 666 2929
Hungary
061 998 0549
Finland
0207 85 1000
Slovakia
012 3300 2554
Romania
212 121 224
Cyprus
22 030 529
Ukraine
044 586 2078
Turkey
212 244 0769
Greece
211 176 8276
Bulgaria
0700 10 218
25
26
27
156988030-00-012009
© Inter IKEA Systems B.V. 2008
AA-401733-1
Download PDF

advertising