Image IMTL49606.0 User's Manual

Image IMTL49606.0 User's Manual
Model No. IMTL49606.0
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
SERVICE DEPARTMENT
Visit our
DIRECTLY.
website at
CALL TOLL-FREE:www.proform.com
new products, prizes,
1-800-753-4645
fitness tips, and much more!
Mon.–Fri. 6 a.m.–6 p.m. MST
Sat. 8 a.m.–5 p.m. MST
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
ON THE WEB:
www.iconservice.com
Visit our website at
Visit our website at
www.healthrider.com
www.jumpking.com
new products, prizes,
fitness tips, and much more!
new products, prizes,
fitness tips, and much more!
CAUTION
Visit our website at
Read all precautions and instructions in this manual
before using
www.nordictrack.com
this equipment. Save this manual
for future reference.new products, prizes,
fitness tips, and much more!
Visit our website at
www.imagefitness.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMAGE is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
page 12. To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 21 if the treadmill is
not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 13).
7. The treadmill should be used only by persons
weighing 275 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
10. When connecting the power cord (see page 12),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
3
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 20.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
24.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never insert any object into any opening.
DANGER: Always unplug the power
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing, or if
it is not legible, call the toll-free telephone number on the front cover of this manual
and order a free replacement decal. Apply the decal in the location shown. Note:
The decals are not shown at actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 17.5 S treadmill. The 17.5 S treadmill combines advanced technology with innovative design to help you get the most from
your exercise in the convenience of your home. And
when you’re not exercising, the 17.5 S treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
number and serial number before calling. The model
number of the treadmill is IMTL49606.0. The serial
number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product model
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Accessory Tray
Console
Handrail
Key/Clip
Upright
Storage Latch
Reset/Off
Circuit Breaker
Walking Belt
Power Cord
Foot Rail
Cushioned Walking Platform
for maximum exercise comfort
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
1/2” Screw (119)–1
3/4” Tek Screw (58)–8
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly
requires two persons. Set the treadmill in a cleared area and remove the packing materials; do not dispose of the
packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with
high-performance lubricant. During shipping, lubricant may be transferred to the top of the walking belt or to the
shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top
of the walking belt, wipe it off with a soft cloth and mild, non-abrasive cleaner.
Assembly requires the included hex keys
mallet
, adjustable wrench
and your own phillips screwdriver
, and needlenose pliers
, rubber
.
To identify assembly hardware, see the drawings below. The number in parentheses below each drawing is the
key number of the part, from the PART LIST in the center of the manual. The number following the parentheses
is the quantity used in assembly. To avoid damaging plastic parts, do not use power tools for assembly.
Silver Ground
Screw (11)–2
3/4" Screw (2)–10
1 1/2" Screw (A)–4
1/4” Star Washer
(21)–2
Nut (47)–2
Upright Bolt (27)–4
Wheel Nut (35)–2
Handrail Star
Washer (19)–4
Wheel Bolt (14)–2
Frame Washer
(33)–2
Console
Bolt (22)–2
Frame Bolt (32)–2
Wheel Spacer
(44)–4
Handrail Bolt (20)–4
1. Attach a Wheel (45) to one side of the Base (48)
with a Wheel Bolt (14), two Wheel Spacers (44),
and a Wheel Nut (35) as shown. Do not overtighten the Wheel Nut; the Wheel should turn
freely.
Upright Star
Washer (39)–4
1
45
A
45 44
44
Attach the other Wheel (45) to the other side
of the Base (48) in the same way.
A
35
14
37
Hole
Attach the four Base Pads (37) to the Base (48)
with four 1 1/2” Screws (A); make sure that the
screws are in the indicated holes in the Base.
37
Hole
37
48
A
A
Hole
37
6
Hole
2. Have a second person orient the Base (48) as
shown.
2
Identify the Left Upright (31), which has a large
hole near the bend as shown.
Bend
31
Orient the Left Upright (31) as shown, and attach
it to the Base (48) with two Upright Bolts (27) and
two Upright Star Washers (39); do not tighten
the Upright Bolts yet.
39
Large Hole
27
48
39
27
3. Orient the Right Upright (36) as shown, and attach it to the Base (48) with two Upright Bolts
(27) and two Upright Star Washers (39); do not
tighten the Upright Bolts yet.
3
48
Bend
39
36
27
39
4. Set the Base (48) near the front of the treadmill,
with the Power Cord (13) on the Hood (1) as
shown.
4
36
13
Cut the small tie (not shown) holding the Upright
Wire (28) in a bundle.
36
Strap
Wrap the strap around the Upright Wire (28) and
secure the strap using the included plastic tie.
Then, pull the opposite end of the strap until the
end of the Upright Wire is pulled through the
Right Upright (36).
28
Tie
28
48
7
5. See the left inset drawing. Identify the two Frame
Spacers (34). Open the included packet of
grease, and apply grease to both sides of both
Frame Spacers. Then, identify the outer side of
each Frame Spacer.
5
36
91
47
Next, hold a Frame Spacer (34) between the
Right Upright (36) and the Lift Frame (59), with
the outer side of the Frame Spacer facing the
Right Upright. Attach the Right Upright to the
Lift Frame with a Frame Bolt (32), a Frame
Washer (33), and a Nut (47); do not tighten the
Frame Bolt yet.
34
33
59
Then, identify the Right Base Cover (91). Slide
the Right Base Cover onto the Right Upright (36)
and turn it to the position shown.
28
Pull gently on the upper end of the Upright Wire
(28) to remove any excess slack.
34
32
36
47
Outer
Side
Cut the plastic tie and remove the strap from the
Upright Wire (28).
33 32
Inner
Side
34
59
6. See the left inset drawing. Identify the outer side
of the remaining Frame Spacer (34).
6
90
Hold the Frame Spacer (34) between the Left
Upright (31) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Left Upright. Attach the Left Upright to the Lift
Frame with a Frame Bolt (32), a Frame Washer
(33), and a Nut (47); do not tighten the Frame
Bolt yet.
31
47
34
33
Identify the Left Base Cover (90). Slide the Left
Base Cover onto the Left Upright (31) and turn it
to the position shown.
59
32
34
31
47
Outer
Side
32
Inner
Side
8
33
34
59
7. Set the console assembly face down on a soft
surface to avoid scratching it. Hold a Handrail
(18) near the console assembly.
7
Console
Wire
Next, insert the console wire into the hole in the
bottom of the Handrail (18) and out of the indicated square hole. If necessary, grip the connector with needlenose pliers only in the area
indicated by the arrow (see the inset drawing.)
Then, attach the ground wire to the Handrail with
a Silver Ground Screw (11).
22
18
21
2
Square
Hole
Next, set the Handrail (18) on the console assembly. Make sure that no wires are pinched.
Finger tighten a Console Bolt (22) with a 1/4”
Star Washer (21) into the Handrail, and then
start two 3/4” Screws (2) into the Handrail.
Tighten the Console Bolt and then the two
Screws; do not overtighten the Screws.
Ground
Wire
11
Console
Assembly
Attach the other Handrail (not shown) to the console assembly in the same way. Note: There are
no wires on the other side.
8. Insert the Upright Wire (28) through a Handrail
Spacer (88) as shown. Attach the Handrail
Spacer to the Right Upright (36) with a 3/4”
Screw (2). Remove the stap and tie from the
Upright Wire.
8
88
2
Attach the other Handrail Spacer (not shown) to
the Left Upright (not shown) as described above.
Note: There is not a wire on the left side.
28
36
Tie
Strap
9. While another person holds the Console Base
(26) near the right Handrail (18), connect the
console wire to the Upright Wire (28) as shown
in the inset drawing. Important: If the connectors are oriented correctly, they will slide together easily and snap into place. If the connectors are not oriented correctly, the console may be damaged when the power is
turned on. Insert the connectors into the Right
Upright (36).
9
18
26
36
Console Wire
28
Attach the Console Base (26) to the Right
Upright (36) and the Left Upright (not shown)
with four Handrail Bolts (20) and four Handrail
Star Washers (19) (only one side is shown).
Start all four Handrail Bolts before tightening
any of them.
19
20
19
20
9
28
10. Lower the Uprights (31, 36).
10
Side View
32
See the inset drawing. Position the Uprights (31,
36) so that the treadmill Frame (74) is centered
between the Uprights.
27
Firmly tighten the Upright Bolts (27) and the
Frame Bolts (32) on each side of the treadmill.
Do not overtighten the Frame Bolts.
74
31, 36
View from Above
31
11. Raise the Uprights (31, 36).
36
74
11
Rotate the Left and Right Base Covers (90, 91)
180°. Slide the Base Covers over the Base (48).
If necessary, pull out on the sides of the Base
Covers to fit them over the Wheel Bolts (14).
31, 36
90, 91
48
10
14
12. Attach the ground wire on the Upright Wire (28)
to the indicated hole in the Base (48) with a
Silver Ground Screw (11).
12
Grommet
28
Then, press the indicated grommet into the Right
Upright (36).
36
2
Attach the Right Base Cover (91) to the Base
(48) with two 3/4” Screws (2). Attach the Left
Base Cover (not shown) in the same way.
48
Ground
Wire
Raise the Uprights (31, 36) to a vertical position.
11
2
91
13. Press the Latch Sleeve (30) into the Left Upright
(31).
13
31
89
Remove the knob from the pin. Make sure that
the collar and the spring are on the pin. Insert
the pin into the Latch Sleeve (30) and the Left
Upright (31). Press the Latch Insert (89) into the
other side of the Left Upright, and then tighten
the knob back onto the pin.
Knob
30
Spring
Collar
Remove the plastic packaging from the bottom of
the Belly Pan.
Pin
14. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 22). To protect the floor or carpet, place a mat under the treadmill.
11
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free telephone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
12
CONSOLE DIAGRAM
Note: If there are sheets of clear plastic
on the console, remove the plastic.
Clip
Key
FEATURES OF THE CONSOLE
Calorie Goal Programs
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
The console also features four calorie goal programs.
Each program controls the speed and incline of the
treadmill to help you burn unwanted pounds.
To use the manual mode of the console, follow the
steps beginning on page 14. To use a distance program, see page 16. To use a step program, see
page 17. To use a calorie goal program, see page
18.
Distance Goal Programs
HOW TO TURN ON THE POWER
In addition, the console offers two distance programs—
the 5K program counts down from 5 kilometers as you
complete a 5-kilometer run, and the 10K program
counts down from 10 kilometers.
Plug in the power cord (see
page 12). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
Step Program
Walking is one of the most popular exercises worldwide. Walking does not require advanced conditioning
or special skills, yet it produces numerous benefits,
such as increased calorie burning, a slimmer waist,
toned muscles, enhanced energy and stamina, lower
blood pressure, and reduced stress.
Reset
Position
To track your walking exercise, the console features a
new step program that counts the number of steps that
you take during each workout. In addition, the console
offers a step program that allows you to enter the number of steps that you plan to walk, and counts down the
steps as you exercise.
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console; after a
moment, the display will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
More reliable than conventional pedometers, the treadmill’s step program is highly accurate with most users.
Note: To prevent damage to the walking platform,
always wear clean shoes while using the treadmill.
13
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the numbered
speed buttons.
HOW TO USE THE MANUAL MODE
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
13.
2
Note: The first time you use the treadmill, periodically inspect the alignment of the walking belt, and
center it if necessary (see page 22).
Enter your weight if desired.
5
For the most accurate
calorie count, enter your
weight into the console
by pressing the Weight
increase and decrease
buttons repeatedly. Note:
Once you have entered your weight, your weight
will be saved in memory.
3
To change the incline of
the treadmill, press the
Incline increase and decrease buttons or one of
the numbered incline buttons. Each time the
Incline increase or decrease button is pressed,
the incline will change by 0.5%. If one of the numbered incline buttons is pressed, the treadmill will
adjust to the selected incline setting. Note: After
the buttons are pressed, it may take a moment for
the treadmill to reach the selected incline setting.
Select the manual mode.
When the
key is inserted, the
manual
mode will be
Track
selected. If
you have selected a program, press the Calorie Goal
Programs button repeatedly until a track appears
in the display.
4
Change the incline of the treadmill as desired.
6
Follow your progress with the display.
When the
manual mode
Track
is selected,
the upper
part of the
display will
show a track
that represents 1/4 mile. As you walk or run, indicators will appear in succession around the track
until the entire track appears. The track will then
disappear and the indicators will again begin to appear in succession.
Start the walking belt.
To start the walking belt, press the Start button,
the Speed increase button, or one of the numbered speed buttons.
If the Start button or the Speed increase button is
pressed, the walking belt will begin to move at 1
mph. As you exercise, change the speed of the
walking belt as desired by pressing the Speed increase and decrease buttons. Each time a button
is pressed, the speed
setting will change by
0.1 mph; if a button is
held down, the speed
setting will change in increments of 0.5 mph.
The left side of the display
will show the elapsed
time, the distance that
you have walked or run,
and the incline level of the
treadmill. Note: When a
calorie goal program is selected, the display will
show the time remaining in the program instead of
the elapsed time.
The right side of the display will show the approximate number of
calories you have
burned, the speed of the
walking belt, and your
pace in minutes per mile. The right side of the display will also show your heart rate when you use
the handgrip pulse sensor.
If one of the numbered speed buttons is pressed,
the walking belt will gradually increase in speed
until it reaches the selected speed setting. Note:
The console can display speed and distance in
either miles or kilometers (see THE INFORMATION MODE/DEMO MODE on page 19). For
simplicity, all instructions in this section refer
to miles.
14
Note: For the treadmill to count your steps accurately, correct walking form is important. As you
walk, try to maintain a steady pace, a uniform
stride length, and a consistent position on the
treadmill. Lighter users may also find it helpful to
reduce the incline of the treadmill or to increase
the speed of the walking belt. IMPORTANT:
Always exercise at a pace that is comfortable
for you.
8
To turn on the fan at low speed, press the Fan
button; the word “Low” will appear in the display.
To turn on the fan at high speed, press the button
a second time; the word “High” will appear in the
display. To turn off the fan, press the button a third
time; the word “Off” will appear in the display.
Note: If the fan is left on when the walking belt is
stopped, the fan will automatically turn off after a
few minutes.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
7
9
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
make sure that
your hands are clean.
Turn on the fan if desired.
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position, or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 19 and turn off the
demo mode.
Metal Contacts
To measure your heart rate, stand on the foot
rails and place your hands on the metal contacts—avoid moving your hands. When your
pulse is detected, the heart symbol in the display
will begin to flash each time your heart beats, one
or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
at least 15 seconds.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
15
Note: To change the speed of the walking belt or
the incline of the treadmill at any time during the
program, press the Speed or Incline buttons.
HOW TO USE A DISTANCE PROGRAM
1
Insert the key into the console.
The left side of the display will show the number
of kilometers still to be run every few seconds.
See HOW TO TURN ON THE POWER on page
13.
2
To stop the program at any time, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button. The
walking belt will begin to move at 1 mph. Adjust
the speed of the walking belt as desired by pressing the Speed increase or decrease button or one
of the numbered Speed buttons.
Select a distance program.
To select a
distance program, press
the Distance
Goal
Programs
button once
or twice until
a distance
goal of 5.000 or 10.00 (kilometers) appears in the
left side of the display. When a distance program
is selected, the maximum speed setting of the
program will flash in the right side of the display
for a few seconds and the maximum incline setting of the program will appear in the left side of
the display.
3
When you have completed a 5-kilometer run or a
10-kilometer run, your total time and the word
“cool” (meaning cool down) will appear in the left
side of the display. If the speed of the walking belt
was greater than 5 mph when you completed your
run, the walking belt will then slow to 5 mph for
one minute. After one minute, the walking belt will
slow to 4 mph for 2 minutes. The walking belt will
then slow to 3 mph for 2 minutes. The walking belt
will then slow to a stop.
4
Press the Start button to start the program.
Follow your progress with the display.
See step 6 on pages 14 and 15.
A moment after the button is pressed, the walking
belt will begin to move at 3 mph. Hold the
handrails and begin walking.
5
Measure your heart rate if desired.
See step 7 on page 15.
Near the end of the second minute of the program, the speed setting will flash in the display
and a series of tones will sound. The speed of the
walking belt will then increase to 4 mph.
6
Turn on the fan if desired.
See step 8 on page 15.
Near the end of the third minute of the program,
the speed setting will flash in the display and a series of tones will sound. The speed of the walking
belt will then increase to 5 mph.
7
When you are finished exercising, remove the
key from the console.
See step 9 on page 15.
Near the end of the fourth minute of the program,
the speed setting will flash in the display and a series of tones will sound. The speed of the walking
belt will then increase to 6.5 mph.
16
3
HOW TO USE A STEP PROGRAM
1
Insert the key into the console.
A moment after the button is pressed, the walking
belt will begin to move at 2 mph. Hold the
handrails and begin walking.
See HOW TO TURN ON THE POWER on page
13.
2
Press the Start button or the Speed increase
button to start the program.
As you exercise, adjust the speed and incline of
the treadmill as desired by pressing the Speed
and Incline buttons.
Select a step program.
To select a
step program, press
the 10,000
Steps
Program button or the
Goal increase button; if you press the 10,000 Steps Program button, a goal of 10,000 steps will appear in the
upper display. Note: If the walking belt is moving
when the 10,000 Steps Program button is
pressed, the walking belt will slow to a stop.
During the program, the upper display will show
the number of steps still to be taken. When only
ten steps remain, the upper left of the display will
flash and a tone will sound repeatedly until you
reach the goal. The walking belt will then slow to a
stop.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 2 mph. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
Depending on your fitness level, you may desire
to walk fewer than or more than 10,000 steps. To
change the goal, press the Goal increase and decrease buttons. Each time a button is pressed, the
goal will change by 500 steps. Note: The goal can
be changed either before or after the program is
started.
4
Follow your progress with the display.
See step 6 on pages 14 and 15.
5
Measure your heart rate if desired.
See step 7 on page 15.
Note: To find an appropriate starting goal, walk on
the treadmill with the manual mode selected (see
page 14), and note the number of steps that you
walk during your workout. Then, round that number up to the nearest 500 steps. This can be a
starting goal. As your fitness level improves, you
can increase the goal by 500 steps every few
weeks. IMPORTANT: Always exercise at an intensity level and for a length of time that is
comfortable for you.
6
Turn on the fan if desired.
See step 8 on page 15.
7
When the program is completed, remove the
key from the console.
See step 9 on page 15.
17
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
HOW TO USE A CALORIE GOAL PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 13.
2
Enter your weight.
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment. Note: If all seven of the indicators in the
Current Segment column are lit, the speed settings
may move downward so that only the highest indicators appear in the matrix.
See step 2 on page 14. Note: Always enter your
weight before using a calorie goal program;
the speed and incline settings of the program
will depend on the weight setting you enter.
3
Select a calorie goal program.
To select a
calorie goal
program,
press the
Calorie Goal
Programs
button repeatedly. As
each calorie
goal program is selected, the maximum speed
setting of the program and the maximum incline
setting of the program will flash in the display for a
few seconds and the display will show how long
the program will last. A profile of the speed settings of the program will scroll across the display.
4
If the speed or incline setting for the current segment is too high or too low, you can manually
override the setting by pressing the Speed and
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column.
Important: When the current segment of the
program ends, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings
for that segment.
Press the Start button to start the program.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
The program will continue in this way until the last
segment of the program ends. The walking belt
will then slow to a stop. Important: The calorie
goal is an estimate of the number of calories
that you will burn during the program. The actual number of calories that you burn will depend on your weight. In addition, if you manually change the speed or incline of treadmill
during the program, the number of calories
you burn will be affected.
Each program is divided into 30 or 40 one-minute
segments. One speed setting and one incline setting are programmed for each segment. Note: The
same speed and/or incline setting may be programmed for two or more consecutive segments.
The speed
setting for
the first segment will be
Current Segment
shown in the
flashing
Current
Segment column of the matrix. (The incline settings are not shown in the matrix.) The speed settings for the following segments will be shown in
the columns to the right.
18
5
6
Follow your progress with the display.
THE INFORMATION MODE
See step 6 on pages 14 and 15.
The console features an information mode that keeps
track of treadmill usage information. The information
mode also allows you to select miles or kilometers as
the unit of measurement and to turn on and turn off the
demo mode.
Measure your heart rate if desired.
See step 7 on page 15.
7
Turn on the fan if desired.
See step 8 on page 15.
8
When the program is completed, remove the
key from the console.
See step 9 on page 15.
To select the information mode, hold down the Stop
button, insert the key into the console, and then release
the Stop button. When the information mode is selected, the following information will appear in the display:
The upper display
will show the total
number of thousands of steps
taken by all users
of the treadmill.
For example, the
number 316 would indicate 316,000 steps taken.
The center of the
display will show
the number of
hours that the
treadmill has been
operated. The
lower right corner
of the display will show the total number of miles or kilometers that the walking belt has moved.
In addition, an “E” for English miles or an “M” for metric
kilometers will appear in the right side of the display. To
change the unit of measurement, press the Speed increase button.
IMPORTANT: If a “d” appears in the display, the console is in the “demo” mode. This mode is intended to be
used only when the treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the indicators in the display will automatically appear in a preset sequence; the buttons on the
console will not operate. If a “d” appears when the information mode is selected, press the Speed decrease button so the “d” disappears.
Note: If you press the Calorie Goal Programs button
while in the information mode, the display may appear
very dim, very dark, or blank. If this happens, press the
Calorie Goal Programs button repeatedly until the display looks right.
To exit the information mode, remove the key from the
console.
19
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails. To
raise the frame, bend your legs, keep your back straight,
and lift with your legs. Raise the frame about halfway to the
vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the catch passes the
pin on the latch knob, and then slowly release the latch knob.
Make sure that the pin is resting securely against the
catch.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Latch
Knob
Engaged
Catch
HOW TO MOVE THE TREADMILL
Deck
Before moving the treadmill, convert it to the storage position as
described above. Make sure that the pin on the latch knob is
resting securely against the catch.
1. Hold one of the handrails and place your other hand on the
deck. Place one foot against one of the wheels.
Handrail
2. Tilt the treadmill back until it rolls freely on the wheels. Carefully
move the treadmill to the desired location. To reduce the risk
of injury, use extreme caution while moving the treadmill.
Do not move the treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
Wheel
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the upper end of the treadmill with your left hand. Pull the latch knob to the left and hold it. Pivot the
frame downward and then release the latch knob.
2. Hold the metal frame firmly with both hands, and lower it to the floor. CAUTION: To decrease the possibility
of injury, do not lower the frame by gripping only the plastic foot rails. Do not drop the frame to the floor.
Make sure to bend your legs and keep your back straight.
20
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 12). Use only a single-outlet surge suppressor that meets all of the specifications described on page 12. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
c
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, please see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the two Foot Rail Screws
(4) and the two 3/4” Hood Screws (2) and carefully remove the Hood (1).
a
2
4
1
Locate the Reed Switch (63) and the Magnet (67) on
the left side of the Pulley (64). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 1/8". If necessary, loosen the
Screw (11), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Hood (not shown),
and run the treadmill for a few minutes to check for a
correct speed reading.
21
4
1/8"
11
64
63
67
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 12.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 inches off
the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
b
2"–3"
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 2 to 3 inches off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
a
b
PROBLEM: No exercise information appears in the console display when the power is turned on and the
key is inserted in the console.
SOLUTION: a. Remove the key from the console. Press the Stop button while reinserting the key into the console. Then, press the Calorie Goal Programs button. Exercise information should now appear in
the console display.
b. If there is still no text in the console display, please see the front cover of this manual.
22
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
23
PART LIST—Model No. IMTL49606.0
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
1
34
1
8
2
2
11
2
1
1
6
2
1
2
2
1
4
2
4
4
2
2
1
2
1
1
4
1
1
1
1
2
4
2
2
1
4
14
5
1
2
1
1
4
2
3
4
1
3
1
1
2
Description
Hood
3/4" Screw
Left Foot Rail
Foot Rail Screw
Motor Tension Bolt
Motor Tension Washer
Wire Tie
Motor Bolt
Drive Motor
Motor Bracket
Sliver Ground Screw
Power Bracket Star Washer
Power Cord Assembly
Wheel Bolt
Foot Rail Decal
Console Fan Assembly
Handrail Endcap
Handrail
Handrail Star Washer
Handrail Bolt
1/4" Star Washer
Console Bolt
Key/Clip
Frame Pivot Spacer
Console
Console Base
Upright Bolt
Upright Wire
Latch Pin Assembly
Latch Sleeve
Left Upright
Frame Bolt
Frame Washer
Frame Spacer
Wheel Nut
Right Upright
Base Pad
3/4" Tek Screw
Upright Star Washer
5/32" Hex Key
Caution Decal
Console Support Bracket
Warning Decal
Wheel Spacer
Wheel
Incline Motor Nut, Top
Nut
Base
Plastic Tie
Belly Pan
Controller
Upright Endcap
Key No. Qty.
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
#
#
#
#
#
2
6
1
1
1
1
1
2
1
1
1
1
1
2
1
2
2
2
4
1
1
1
1
4
6
6
1
1
4
2
1
1
1
2
2
2
1
1
1
1
4
4
1
1
1
1
1
1
1
R0407A
Description
Lift Frame Bolt
3/8" Nut
Lift Motor
Stop Bracket
Incline Motor Bolt, Top
Incline Motor Bolt, Bottom
Lift Frame
Motor Tension Nut
Motor Belt
Reed Switch
Clip
Front Roller/Pulley
Motor Pivot Bolt
Platform Bolt, Front
Magnet
Belt Guide
Rear Roller Bracket
Isolator
Belt Guide Screw
Walking Belt
Walking Platform
Frame
Right Foot Rail
Platform Nut
Rear Roller Washer
Platform Bolt, Rear
Rear Roller
Right Rear Foot
Rear Roller Star Washer
Rear Roller Bolt
Left Rear Foot
Ground Wire
Hex Key
Roller Bushing
Handrail Spacer Screw
Handrail Spacer
Latch Insert
Left Base Cover
Right Base Cover
Hood Cover
Hood Cover Screw
Isolator Fastener
Reset/Off Circuit Breaker
Catch
4" Black Wire, M/F
8" Green Wire, F/R
8" Blue Wire, 2F
4" Red Wire, M/F
User’s Manual
#These parts are not illustrated
Specifications are subject to change without notice.
82
40
81
38
77
4
84
85
38
83
76
69
78
93
1
43
4
11
82
2
80
77
81
96
79
15
38
70
93
2
94
38
69
76
78
4
3
71
68
72
66
76
4
4
74
73
4
64
49
75
63
89
24
62
92
65
15
70
94
54
67
11
53
33
61
10
5
2
66
9
6
2
38
2
71
39
47
6
4
60
54
8
89
68
59
5
24
76
54
58
27
38
4
54
57
38
12
11
2
95
38
33
17
50
44
14
90
29
41
51
53
41
46
47
55
56
11
12
13
45
88
87
18
7
44
2
35
91
89
16
2
2
31
2
33
30
37
32
21 22
17
2
17
19
20
52
25
87
44
45
2
2
48
27
39
34
18
88
26
35
2
2
44
2
11
28
28
21
17
14
37
36
42
2
2
2
37
34
22
2
2
19
33
20
2
52
2
27
39
32
23
2
2
11
37
2
2
2
EXPLODED DRAWING—Model No. IMTL49606.0
R0407A
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, please see the front cover of this manual. To help us assist you, be prepared to
provide the following information:
• the MODEL NUMBER of the product (IMTL49606.0)
• the NAME of the product (IMAGE 17.5 S treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and PART LIST
attached in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for five (5) years after
the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; to products
used for commercial or rental purposes; or to products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 244084 R0407A
Printed in USA © 2007 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement