Image IMTL39606.2 User's Manual

Image IMTL39606.2 User's Manual
Model No. IMTL39606.2
Serial No.
USER'S MANUAL
Serial Number
Decal
QUESTIONS?
As a manufacturer, we are committed to providing complete
customer satisfaction. If you
have questions, or if parts are
damaged or missing, PLEASE
CONTACT OUR CUSTOMER
Visit our
SERVICE DEPARTMENT
DIRECTLY.
website at
www.proform.com
CALL TOLL-FREE: new products, prizes,
fitness tips, and much more!
1-800-753-4645
Visit our website at
www.weslo.com
new products, prizes,
fitness tips, and much more!
Mon.–Fri., 6 a.m.–6 p.m. MST
ON THE WEB:
www.iconservice.com
Visit our website at
Visit our website at
www.healthrider.com
www.jumpking.com
new products, prizes,
fitness tips, and much more!
new products, prizes,
fitness tips, and much more!
CAUTION
Visit our website at
Read all precautions and instructions in this manual
before using
www.nordictrack.com
this equipment. Save this manual
for future reference.new products, prizes,
fitness tips, and much more!
Visit our website at
www.imagefitness.com
new products, prizes,
fitness tips, and much more!
TABLE OF CONTENTS
IMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
BEFORE YOU BEGIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
OPERATION AND ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
HOW TO FOLD AND MOVE THE TREADMILL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
CONDITIONING GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
HOW TO ORDER REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
LIMITED WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Back Cover
Note: An EXPLODED DRAWING and a PART LIST are attached in the center of this manual.
IMAGE is a registered trademark of ICON IP, Inc.
2
IMPORTANT PRECAUTIONS
WARNING:
To reduce the risk of burns, fire, electric shock, or injury to persons, read the
following important precautions and information before operating the treadmill.
1. It is the responsibility of the owner to ensure
that all users of this treadmill are adequately
informed of all warnings and precautions.
page 11. To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free
telephone number on the front cover of this
manual and order part number 146148, or see
your local electronics store.
2. Use the treadmill only as described.
3. Place the treadmill on a level surface, with at
least eight feet of clearance behind it and two
feet on each side. Do not place the treadmill
on any surface that blocks air openings. To
protect the floor or carpet from damage, place
a mat under the treadmill.
12. Failure to use a properly functioning surge
suppressor could result in damage to the control system of the treadmill. If the control system is damaged, the walking belt may change
speed, accelerate, or stop unexpectedly,
which may result in a fall and serious injury.
4. Keep the treadmill indoors, away from moisture and dust. Do not put the treadmill in a
garage or covered patio, or near water.
13. Keep the power cord and the surge suppressor away from heated surfaces.
14. Never move the walking belt while the power
is turned off. Do not operate the treadmill if
the power cord or plug is damaged, or if the
treadmill is not working properly. (See TROUBLESHOOTING on page 20 if the treadmill is
not working properly.)
5. Do not operate the treadmill where aerosol
products are used or where oxygen is being
administered.
6. Keep children under the age of 12 and pets
away from the treadmill at all times.
15. Read, understand, and test the emergency
stop procedure before using the treadmill (see
HOW TO TURN ON THE POWER on page 12).
7. The treadmill should be used only by persons
weighing 275 pounds or less.
8. Never allow more than one person on the
treadmill at a time.
16. Never start the treadmill while you are standing on the walking belt. Always hold the
handrails while using the treadmill.
9. Wear appropriate exercise clothes when
using the treadmill. Do not wear loose clothes
that could become caught in the treadmill.
Athletic support clothes are recommended for
both men and women. Always wear athletic
shoes. Never use the treadmill with bare feet,
wearing only stockings, or in sandals.
17. The treadmill is capable of high speeds.
Adjust the speed in small increments to avoid
sudden jumps in speed.
18. Never leave the treadmill unattended while it
is running. Always remove the key and unplug
the power cord when the treadmill is not in
use.
10. When connecting the power cord (see page 11),
plug the power cord into a surge suppressor
(not included) and plug the surge suppressor
into a grounded circuit capable of carrying 15
or more amps. No other appliance should be on
the same circuit. Do not use an extension cord.
19. The pulse sensor is not a medical device.
Various factors, including the user's movement, may affect the accuracy of heart rate
readings. The pulse sensor is intended only
as an exercise aid in determining heart rate
trends in general.
11. Use only a single-outlet surge suppressor that
meets all of the specifications described on
3
20. Do not attempt to raise, lower, or move the
treadmill until it is properly assembled. (See
ASSEMBLY on page 6, and HOW TO FOLD
AND MOVE THE TREADMILL on page 18.)
You must be able to safely lift 45 pounds (20
kg) to raise, lower, or move the treadmill.
24.
cord immediately after use, before cleaning
the treadmill, and before performing the
maintenance and adjustment procedures described in this manual. Never remove the
motor hood unless instructed to do so by an
authorized service representative. Servicing
other than the procedures in this manual
should be performed by an authorized service representative only.
21. When folding or moving the treadmill, make
sure that the storage latch is fully closed.
22. Inspect and properly tighten all parts of the
treadmill regularly.
23. Never insert any object into any opening.
DANGER: Always unplug the power
25. This treadmill is intended for in-home use
only. Do not use this treadmill in a commercial, rental, or institutional setting.
WARNING:
Before beginning this or any exercise program, consult your physician. This
is especially important for persons over the age of 35 or persons with pre-existing health problems.
Read all instructions before using. ICON assumes no responsibility for personal injury or property
damage sustained by or through the use of this product.
SAVE THESE INSTRUCTIONS
The decals shown here have been placed on the treadmill. If a decal is missing, or if
it is not legible, call the toll-free telephone number on the front cover of this manual
and order a free replacement decal. Apply the decal in the location shown. Note:
The decals are not shown at actual size.
4
BEFORE YOU BEGIN
Thank you for selecting the new IMAGE® 15.5 S treadmill. The 15.5 S treadmill combines advanced technology with innovative design to help you get the most from
your exercise in the convenience of your home. And
when you’re not exercising, the 15.5 S treadmill can be
folded up, requiring less than half the floor space of
other treadmills.
number and serial number before calling. The model
number of the treadmill is IMTL39606.2. The serial
number can be found on a decal attached to the treadmill (see the front cover of this manual for the location).
To avoid a registration fee for any service needed
under warranty, you must register the treadmill at
www.iconservice.com/registration.
For your benefit, read this manual carefully before
using the treadmill. If you have questions after reading this manual, please see the front cover of this manual. To help us assist you, note the product model
Before reading further, please review the drawing
below and familiarize yourself with the labeled parts.
Fan
Accessory Tray
Console
Handrail
Key/Clip
Storage Latch
Upright
Reset/Off
Circuit Breaker
Walking Belt
Power Cord
Foot Rail
Cushioned Walking Platform
for maximum exercise comfort
BACK
RIGHT SIDE
Rear Roller
Adjustment Bolts
5
1/2” Screw (119)–1
3/4” Tek Screw (58)–8
ASSEMBLY
To hire an authorized service technician to assemble the treadmill, call toll-free 1-800-445-2480. Assembly
requires two persons. Set the treadmill in a cleared area and remove the packing materials; do not dispose of the
packing materials until assembly is completed. Note: The underside of the treadmill walking belt is coated with
high-performance lubricant. During shipping, lubricant may be transferred to the top of the walking belt or to the
shipping carton. This is a normal condition and does not affect treadmill performance. If there is lubricant on top
of the walking belt, wipe it off with a soft cloth and mild, non-abrasive cleaner.
Assembly requires the included hex keys
mallet
, adjustable wrench
and your own phillips screwdriver
, and wire cutters
.
, rubber
To identify assembly hardware, see the drawings below. The number in parentheses below each drawing is the
key number of the part, from the PART LIST in the center of the manual. The number following the parentheses
is the quantity used in assembly. To avoid damaging plastic parts, do not use power tools for assembly.
Handrail Bolt (20)–4
Upright Bolt/Wheel Bolt (27)–6
3/4" Screw (2)–6
Silver Ground
Screw (87)–2
Frame Bolt (32)–2
Console
Bolt (22)–2
1. Orient the Base (48) as shown.
Wheel Spacer
(44)–4
Frame Washer
(33)–2
1/4" Star Washer
(21)–2
Handrail Star
Washer (19)–4
Upright Star
Washer (39)–4
Nut (47)–4
1
Identify the Right Upright (36), which has a
square hole near the lower end.
36
Orient the Right Upright (36) as shown, and
attach it to the Base (48) with two Upright Bolts
(27) and two Upright Star Washers (39); do not
tighten the Upright Bolts yet.
48
Square
Hole
39
27
39
27
Wheel Bolt (40)–2
6
2. Orient the Left Upright (31) as shown, and attach
it to the Base (48) with two Upright Bolts (27) and
two Upright Star Washers (39); do not tighten
the Upright Bolts yet.
2
Latch
Holes
48
31
39
39
3. Attach a Wheel (45) to each side of the Base
(48) with a Wheel Bolt (27), two Wheel Spacers
(44), and a Nut (47) as shown. Do not overtighten the Wheel Bolts; the Wheels should
turn freely.
3
45
27
44
44
27
47
45
44
44
47
48
27
4. Turn the Base (48) over, and set it near the front
of the treadmill as shown.
4
Large
Hole
Cut the tie holding the Upright Wire (28) in a bundle. Leave the large colored tie on the end of
the Upright Wire.
48
Tie
31
Insert the Upright Wire (28) into the large hole at
the bottom of the Right Upright (36) (see the
inset drawing) and out of the top.
28
Raise the Uprights (31, 36) so the Base (48) is
flat on the floor. Make sure that the end of the
Upright Wire (28) does not fall into the Right
Upright. It may be helpful to bend the colored
tie on the end of the Upright Wire over the
Right Upright.
36
Colored Tie
28
7
28
5. Raise the Uprights (31, 36).
5
31
See the left inset drawing. Identify the two Frame
Spacers (34). Open the included packet of
grease, and apply grease to both sides of both
Frame Spacers. Then, identify the outer side of
each Frame Spacer.
36
47
34
Hold the Frame Spacer (34) between the Right
Upright (36) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Right Upright. Attach the Right Upright to the
Lift Frame with a Frame Bolt (32), a Frame
Washer (33), and a Nut (47); do not tighten the
Frame Bolt yet.
33
32
59
34
36
47
Outer
Side
33 32
Inner
Side
34
59
6. See the left inset drawing. Identify the outer side
of the remaining Frame Spacer (34).
6
31
47
Hold the Frame Spacer (34) between the Left
Upright (31) and the Lift Frame (59), with the
outer side of the Frame Spacer facing the
Left Upright. Attach the Left Upright to the Lift
Frame with a Frame Bolt (32), a Frame Washer
(33), and a Nut (47); do not tighten the Frame
Bolt yet.
34
33
32
59
34
31
47
Outer
Side
32
Inner
Side
8
33
34
59
7. Route the Upright Wire (28) through one of the
Handrails (18) as shown, and remove the tie
from the Upright Wire.
7
20
Attach the Handrail (18) to the Right Upright (36)
with two Handrail Bolts (20) and two Handrail
Star Washers (19). Be careful not to pinch the
Upright Wire (28).
19
Attach the other Handrail (18) to the Left Upright
(31) with two Handrail Bolts (20) and two
Handrail Star Washers (19).
18
Tie
28
31
20
19
18
36
8. While another person holds the Console Base
(26) near the right Handrail (18), attach the
ground wire on the Console Base to the right
Handrail with a Silver Ground Screw (87).
8
26
Ground
Wire
87
Wire
Harness
Connect the wire harness on the Console Base
(26) to the Upright Wire (28) as shown in the
inset drawing. Important: If the connectors are
oriented correctly, they will slide together
easily and snap into place. If the connectors
are not oriented correctly, the console may
be damaged when the power is turned on.
28
18
28
9. Insert the wires into the Console Base (26) as
you set the Console Base on the Handrails. Be
careful not to pinch the wires. Next, thread two
Console Bolts (22) with 1/4" Star Washers (21)
into the Handrails and the Console Base; do not
tighten the Console Bolts yet.
9
26
Front View
18
18
Attach the Console Base (26) to the Handrails
(18) with four 3/4" Screws (2). Then, tighten the
two Console Bolts (22).
21
2
9
22
2
21
22
10. Lower the Uprights (31, 36).
10
32
Side View
See the inset drawing. Position the Uprights (31,
36) so that the treadmill Frame (74) is centered
between the Uprights.
40
Firmly tighten the Frame Bolts (32) and then the
Upright Bolts (40) on each side of the treadmill.
Do not overtighten the Frame Bolts.
31, 36
74
View from Above
31
11. Attach the ground wire on the Upright Wire (28)
to the indicated hole in the Base (48) with a
Silver Ground Screw (87).
36
74
11
Grommet
36
28
Press the indicated grommet into the Right
Upright (36).
Raise the Uprights (31, 36).
48
Ground
Wire
87
12. Attach the Latch Housing (30) to the Left Upright
(31) with two 3/4" Screws (2). Make sure that
the large hole in the Latch Housing is on the
side shown. Do not overtighten the Screws.
12
30
Knob
Remove the knob from the pin. Make sure that
the collar and the spring are on the pin as
shown. Insert the pin into the Latch Housing
(30), and tighten the knob back onto the pin.
31
2
Pin
Spring
Collar
13. Make sure that all parts are properly tightened before you use the treadmill. Note: Extra hardware may
be included. Keep the included hex keys in a secure place; the large hex key is used to adjust the walking belt
(see page 21). To protect the floor or carpet, place a mat under the treadmill.
10
OPERATION AND ADJUSTMENT
THE PRE-LUBRICATED WALKING BELT
tric shock. This product is equipped with a cord having
an equipment-grounding conductor and a grounding
plug. Plug the power cord into a surge suppressor,
and plug the surge suppressor into an appropriate
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.
Important: The treadmill is not compatible with
GFCI-equipped outlets.
Your treadmill features a walking belt coated with highperformance lubricant. IMPORTANT: Never apply silicone spray or other substances to the walking
belt or the walking platform. Such substances will
deteriorate the walking belt and cause excessive
wear.
HOW TO PLUG IN THE POWER CORD
This product is for use on a nominal 120-volt circuit,
and has a grounding plug that looks like the plug illustrated in drawing 1 below. A temporary adapter that
looks like the adapter illustrated in drawing 2 may be
used to connect the surge suppressor to a 2-pole
receptacle as shown in drawing 2 if a properly
grounded outlet is not available.
DANGER: Improper connection
of the equipment-grounding conductor can
result in an increased risk of electric shock.
Check with a qualified electrician or serviceman if you are in doubt as to whether the
product is properly grounded. Do not modify
the plug provided with the product—if it will
not fit the outlet, have a proper outlet
installed by a qualified electrician.
1
Grounded Outlet Box
Surge Suppressor
Grounding Pin
Your treadmill, like any other type of sophisticated
electronic equipment, can be seriously damaged by
sudden voltage changes in your home’s power.
Voltage surges, spikes, and noise interference can
result from weather conditions or from other appliances
being turned on or off. To decrease the possibility of
your treadmill being damaged, always use a surge
suppressor with your treadmill (see drawing 1 at
the right). To purchase a surge suppressor, see
your local IMAGE dealer or call the toll-free telephone number on the front cover of this manual
and order part number 146148, or see your local
electronics store.
Grounding Pin
Grounded Outlet
Grounding Plug
2
Grounded Outlet Box
Adapter
Use only a single-outlet surge suppressor that is
UL 1449 listed as a transient voltage surge suppressor (TVSS). The surge suppressor must have a
UL suppressed voltage rating of 400 volts or less
and a minimum surge dissipation of 450 joules.
The surge suppressor must be electrically rated for
120 volts AC and 15 amps. There must be a monitoring light on the surge suppressor to indicate
whether it is functioning properly. Failure to use a
properly functioning surge suppressor could result
in damage to the control system of the treadmill. If
the control system is damaged, the walking belt
may change speed, accelerate or stop unexpectedly, which may result in a fall and serious injury.
Surge Suppressor
Lug
Metal Screw
The temporary adapter should be used only until a
properly grounded outlet (drawing 1) can be installed
by a qualified electrician.
The green-colored rigid ear, lug, or the like extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box cover.
Whenever the adapter is used it must be held in place
by a metal screw. Some 2-pole receptacle outlet box
covers are not grounded. Contact a qualified electrician to determine if the outlet box cover is
grounded before using an adapter.
This product must be grounded. If it should malfunction or break down, grounding provides a path of least
resistance for electric current to reduce the risk of elec-
11
CONSOLE DIAGRAM
Note: If there are sheets of clear plastic
on the console, remove the plastic.
Clip
Key
FEATURES OF THE CONSOLE
Calorie Goal Programs
The treadmill console offers a selection of features
designed to make your workouts more effective. When
the manual mode of the console is selected, the speed
and incline of the treadmill can be changed with the
touch of a button. As you exercise, the console will
display continuous exercise feedback. You can even
measure your heart rate using the built-in pulse sensor.
The console also features four calorie goal programs.
Each program controls the speed and incline of the
treadmill to help you burn unwanted pounds.
To use the manual mode of the console, follow the
steps beginning on page 13. To use a step program,
see page 15. To use a calorie goal program, see
page 16.
Step Program
HOW TO TURN ON THE POWER
Walking is one of the most popular exercises worldwide. Walking does not require advanced conditioning
or special skills, yet it produces numerous benefits,
such as increased calorie burning, a slimmer waist,
toned muscles, enhanced energy and stamina, lower
blood pressure, and reduced stress.
Plug in the power cord (see
page 11). Next, locate the
reset/off circuit breaker on
the treadmill frame near the
power cord. Make sure that
the circuit breaker is in the
“reset” position.
To track your walking exercise, the console features a
new step program that counts the number of steps that
you take during each workout. In addition, the console
offers a step program that allows you to enter the number of steps that you plan to walk, and counts down the
steps as you exercise.
Reset
Position
Next, stand on the foot rails of the treadmill. Locate the
clip attached to the key (see the drawing above), and
slide the clip securely onto the waistband of your
clothes. Then, insert the key into the console; after a
moment, the display will light. Important: In an
emergency situation, the key can be pulled from
the console, causing the walking belt to slow to a
stop. Test the clip by carefully taking a few steps
backward; if the key is not pulled from the console,
adjust the position of the clip.
More reliable than conventional pedometers, the treadmill’s step program is highly accurate with most users.
For the best results, try to maintain a steady pace, a
uniform stride length, and a consistent position on the
treadmill as you walk. Lighter users may also find it
helpful to reduce the incline of the treadmill or to
increase the speed of the walking belt.
Note: To prevent damage to the walking platform,
always wear clean shoes while using the treadmill.
12
To stop the walking belt, press the Stop button.
The time will begin to flash in the display. To
restart the walking belt, press the Start button, the
Speed increase button, or one of the ten numbered buttons.
HOW TO USE THE MANUAL MODE
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page
12.
2
Note: The first time you use the treadmill, periodically inspect the alignment of the walking belt, and
center it if necessary (see page 21).
Enter your weight if desired.
5
For the most accurate
calorie count, enter
your weight into the
console by pressing
the weight (WT.) increase and decrease
buttons repeatedly. Note: Once you have entered
your weight, your weight will be saved in memory.
3
To change the incline of the treadmill, press the
Incline increase and decrease buttons. Each time
a button is pressed, the incline setting will change
by 0.5%; if a button is held down, the incline setting will change quickly.
6
Select the manual mode.
Follow your progress with the display.
When the manual mode
or a step program is selected, a track representing 1/4 mile will appear in the upper right
corner of the display.
As you walk or run on the treadmill, the indicators
around the track will appear in succession until the
entire track appears. The track will then disappear
and the indicators will again begin to appear in
succession.
When the key is inserted, the manual
mode will be selected.
If a program has been
selected, press the
Calorie Goal Programs
button repeatedly until a track appears in the display.
4
Change the incline of the treadmill as desired.
Start the walking belt.
The lower left corner of
the display can show
the elapsed time, the
distance that you have
walked or run during
your workout, and the
incline level of the treadmill. Note: During a calorie
goal program, the display will show the time remaining in the program instead of the elapsed
time.
To start the walking belt, press the Start button,
the Speed increase button, or one of the buttons
numbered 1 through 10.
If the Start button or
the Speed increase
button is pressed, the
walking belt will begin
to move at 1 mph. As
you exercise, change
the speed of the walking belt as desired by pressing the Speed increase and decrease buttons.
Each time a button is pressed, the speed setting
will change by 0.1 mph; if a button is held down,
the speed setting will change in increments of 0.5
mph.
The lower right corner
of the display can show
the speed of the walking belt and the approximate number of calories that you have
burned during your workout. The lower right corner of the display will also show your heart rate
when you use the handgrip pulse sensor.
If one of the ten numbered buttons is pressed, the
walking belt will gradually increase in speed until it
reaches the selected speed setting. Note: The
console can display speed and distance in either miles or kilometers (see THE INFORMATION MODE/DEMO MODE on page 17). For
simplicity, all instructions in this section refer
to miles.
13
To measure your heart rate, stand on the foot
rails and place your hands on the metal contacts—avoid moving your hands. When your
pulse is detected, the heart symbol in the display
will begin to flash each time your heart beats, one
or two dashes will appear, and then your heart
rate will be shown. For the most accurate heart
rate reading, continue to hold the contacts for
about 15 seconds.
The upper display can
show the elapsed
time, the speed of the
walking belt, the approximate number of
calories that you have
burned, the number of steps you have walked or
run during your workout, or the distance that you
have walked or run. Press the Display button repeatedly until the upper display shows the information that you are most interested in viewing. Note:
When a step program is selected, the display will
show the number of steps still to be taken instead
of the number of steps you have walked or run.
8
To turn on the fan, press the Fan button. To turn
on the fan at high speed, press the button a second time. To turn off the fan, press the button a
third time. Note: If the fan is left on when the walking belt is stopped, the fan will automatically turn
off after a few minutes.
While information is shown in the upper display,
the same information will not be shown in the
lower left or lower right display.
Note: For the treadmill to count your steps accurately, correct walking form is important. As you
walk, try to maintain a steady pace, a uniform
stride length, and a consistent position on the
treadmill. Lighter users may also find it helpful to
reduce the incline of the treadmill or to increase
the speed of the walking belt. IMPORTANT:
Always walk at a speed that is comfortable for
you.
9
When you are finished exercising, remove the
key.
Step onto the foot rails, press the Stop button, and
adjust the incline of the treadmill to the lowest
setting. The incline must be at the lowest setting
when the treadmill is folded to the storage position, or the treadmill will be damaged. Next, remove the key from the console and put it in a secure place. Note: If the display remains lit after
the key is removed, the console is in the
“demo” mode. See page 17 and turn off the
demo mode.
To reset the display, press the Stop button, remove the key, and then reinsert the key.
7
Turn on the fan if desired.
Measure your heart rate if desired.
Before using
the handgrip
pulse sensor,
remove the
sheets of clear
plastic from the
metal contacts.
In addition,
make sure that
your hands are clean.
When you are finished using the treadmill,
switch the reset/off circuit breaker to the “off”
position and unplug the power cord.
Metal Contacts
14
As you exercise, adjust the speed and incline of
the treadmill as desired by pressing the Speed
and Incline buttons.
HOW TO USE A STEP PROGRAM
1
Insert the key into the console.
During the program, the upper display will show
the number of steps still to be taken (unless you
have changed the display by pressing the Display
button). When only ten steps remain, the upper
left of the display will flash and a tone will sound
repeatedly until you reach the goal. The walking
belt will then slow to a stop.
See HOW TO TURN ON THE POWER on page
12.
2
Select a step program.
To select a step program, press the 10,000
Steps Program button
or the Goal increase
button; if you press the
10,000 Steps Program
button, a goal of 10,000 steps will appear in the
upper display. Note: If the walking belt is moving
when the 10,000 Steps Program button is
pressed, the walking belt will slow to a stop.
To stop the program temporarily, press the Stop
button. The time will begin to flash in the display.
To restart the program, press the Start button or
the Speed increase button. The walking belt will
begin to move at 2 mph. To end the program,
press the Stop button, remove the key, and then
reinsert the key.
4
Depending on your fitness level, you may desire
to walk fewer than or more than 10,000 steps. To
change the goal, press the Goal increase and decrease buttons. Each time a button is pressed, the
goal will change by 500 steps. Note: The goal can
be changed either before or after the program is
started.
See step 6 on pages 13 and 14.
5
Measure your heart rate if desired.
See step 7 on page 14.
6
Note: To find an appropriate starting goal, walk on
the treadmill with the manual mode selected (see
page 13), and note the number of steps that you
walk during your workout. Then, round that number up to the nearest 500 steps. This can be a
starting goal. As your fitness level improves, you
can increase the goal by 500 steps every few
weeks. IMPORTANT: Always exercise at an intensity level and for a length of time that is
comfortable for you.
3
Follow your progress with the display.
Turn on the fan if desired.
See step 8 on page 14.
7
When the program is completed, remove the
key from the console.
See step 9 on page 14.
Press the Start button or the Speed increase
button to start the program.
A moment after the button is pressed, the walking
belt will begin to move at 2 mph. Hold the
handrails and begin walking.
15
When the first segment is completed, all speed
settings will move one column to the left. The
speed setting for the second segment will then be
shown in the flashing Current Segment column
and the treadmill will automatically adjust to the
speed and incline settings for the second segment. Note: If all five of the indicators in the
Current Segment column are lit, the speed settings
may move downward so that only the highest indicators appear in the matrix.
HOW TO USE A CALORIE GOAL PROGRAM
1
Insert the key into the console.
See HOW TO TURN ON THE POWER on page 12.
2
Enter your weight.
See step 2 on page 13. Note: Always enter your
weight before using a calorie goal program;
the speed and incline settings of the program
will depend on the weight setting you enter.
3
If the speed or incline setting for the current segment is too high or too low, you can manually
override the setting by pressing the Speed and
Incline buttons. Every few times a Speed button is
pressed, an additional indicator will appear or disappear in the Current Segment column.
Important: When the current segment of the
program ends, the treadmill will automatically
adjust to the speed and incline settings for the
next segment.
Select a calorie goal program.
To select a calorie goal
program, press the
Calorie Goal Programs
button repeatedly. As
each calorie goal program is selected, the
maximum speed setting of the program and the
maximum incline setting of the program will flash
in the display for a few seconds. The display will
then show how long the program will last. A profile
of the speed settings of the program will scroll
across the display.
4
To stop the program at any time, press the Stop
button. To restart the program, press the Start button or the Speed increase button. The walking belt
will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings
for that segment.
Press the Start button to start the program.
The program will continue in this way until the last
segment of the program ends. The walking belt
will then slow to a stop. Important: The calorie
goal is an estimate of the number of calories
that you will burn during the program. The actual number of calories that you burn will depend on your weight. In addition, if you manually change the speed or incline of treadmill
during the program, the number of calories
you burn will be affected.
A moment after the button is pressed, the treadmill will automatically adjust to the first speed and
incline settings of the program. Hold the handrails
and begin walking.
Each program is divided into 30 or 40 one-minute
segments. One speed setting and one incline setting are programmed for each segment. Note: The
same speed and/or incline setting may be programmed for two or more consecutive segments.
5
The speed setting for
Current Period
the first segment will be
shown in the flashing
Current Segment column of the matrix. (The
incline settings are not
shown in the matrix.) The speed settings for the
next four segments will be shown in the columns
to the right.
Follow your progress with the display.
See step 6 on pages 13 and 14.
6
Measure your heart rate if desired.
See step 7 on page 14.
7
Turn on the fan if desired.
See step 8 on page 14.
When only three seconds remain in the first segment of the program, both the Current Segment
column and the column to the right will flash and a
series of tones will sound. If the speed and/or incline of the treadmill is about to change, the speed
setting and/or the incline setting will flash in the
display to alert you.
8
When the program is completed, remove the
key from the console.
See step 9 on page 14.
16
THE INFORMATION MODE/DEMO MODE
The console features an information mode that keeps
track of treadmill usage information and allows you to
select a unit of measurement for the console.
To select the information mode, insert the key into the
console while holding down the Stop button, and then
release the Stop button. When the information mode is
selected, the following information will be shown:
An “E” (for English) or an “M”
(for metric) will appear in the
lower right corner of the display. Press the Speed increase button to change the
unit of measurement, if desired. IMPORTANT: If a “d” appears in the display, the
console is in the “demo” mode. This mode is intended
to be used only when a treadmill is displayed in a store.
When the console is in the demo mode, the power cord
can be plugged in, the key can be removed from the
console, and the display will remain lit, although the
buttons will not operate. If a “d” appears when the information mode is selected, press the Speed decrease button so the “d” disappears.
The upper left corner of the
display will show the total
number of thousands of
steps taken by all users of
the treadmill. For example,
the number 396 would indicate 396,000 steps taken.
The lower left corner of the
display will show the total
number of hours that the
treadmill has been used and
the total number of miles (or
kilometers) that the walking
belt has moved, for a few seconds at a time.
To exit the information mode, remove the key from the
console.
17
HOW TO FOLD AND MOVE THE TREADMILL
HOW TO FOLD THE TREADMILL FOR STORAGE
Before folding the treadmill, adjust the incline to the
lowest position. If this is not done, the treadmill may be permanently damaged. Next, unplug the power cord. CAUTION:
You must be able to safely lift 45 pounds (20 kg) to raise,
lower, or move the treadmill.
1. Hold the metal frame firmly in the location shown by the
arrow at the right. CAUTION: To decrease the possibility
of injury, do not lift the frame by the plastic foot rails.
Make sure you bend your legs and keep your back
straight. As you raise the frame, make sure to lift with
your legs rather than your back. Raise the frame about
halfway to the vertical position.
Frame
2. Move your right hand to the position shown and hold the
treadmill firmly. Using your left hand, pull the latch knob to
the left and hold it. Raise the frame until the hole in the isolator is aligned with the latch pin, and then slowly release the
latch knob. Make sure that the latch pin is fully inserted
into the center of the isolator.
To protect the floor or carpet from damage, place a mat
under the treadmill. Keep the treadmill out of direct sunlight. Do not leave the treadmill in the storage position in
temperatures above 85° Fahrenheit.
Storage
Latch
Isolator
HOW TO MOVE THE TREADMILL
Deck
Before moving the treadmill, convert it to the storage position as
described above. Make sure that the latch pin is fully inserted into the isolator.
Handrails
1. Hold one of the handrails and place your other hand on the
deck. Place one foot against one of the wheels.
2. Tilt the treadmill back until it rolls freely on the wheels.
Carefully move the treadmill to the desired location. To reduce the risk of injury, use extreme caution while moving the treadmill. Do not move the treadmill over an uneven surface.
3. Place one foot against one of the wheels, and carefully lower
the treadmill until it is resting in the storage position.
18
Wheels
Engaged
HOW TO LOWER THE TREADMILL FOR USE
1. Hold the treadmill with your right hand as shown. Pull the
latch knob to the left and hold it. Pivot the frame down until it
is past the latch pin.
Latch
Knob
Frame
2. Hold the metal frame firmly with both hands, and lower it
to the floor. CAUTION: To decrease the possibility of injury, do not lower the frame by gripping only the plastic
foot rails; do not drop the frame to the floor. Make sure to
bend your legs and keep your back straight.
Frame
19
TROUBLESHOOTING
Most treadmill problems can be solved by following the steps below. Find the symptom that applies, and
follow the steps listed. If further assistance is needed, please see the front cover of this manual.
PROBLEM: The power does not turn on
SOLUTION: a. Make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor
is plugged into a properly grounded outlet (see page 11). Use only a single-outlet surge suppressor that meets all of the specifications described on page 11. Important: The treadmill is not compatible with GFCI-equipped outlets.
b. After the power cord has been plugged in, make sure that the key is inserted into the console.
c. Check the reset/off circuit breaker located on the
treadmill frame near the power cord. If the switch
protrudes as shown, the circuit breaker has tripped.
To reset the circuit breaker, wait for five minutes
and then press the switch back in.
c
Tripped
Reset
PROBLEM: The power turns off during use
SOLUTION: a. Check the circuit breaker located on the treadmill frame near the power cord (see the drawing
above). If the circuit breaker has tripped, wait for five minutes and then press the switch back in.
b. Make sure that the power cord is plugged in. If the power cord is plugged in, unplug it, wait for
five minutes, and then plug it back in.
c. Remove the key from the console. Reinsert the key into the console.
d. If the treadmill still will not run, see the front cover of this manual.
PROBLEM: The displays of the console do not function properly
SOLUTION: a. Remove the key from the console and UNPLUG THE
POWER CORD. Remove the two Foot Rail Screws
(4) and the two 3/4” Hood Screws (2) and carefully remove the Hood (1).
2
a
4
1
Locate the Reed Switch (63) and the Magnet (67) on
the left side of the Pulley (64). Turn the Pulley until
the Magnet is aligned with the Reed Switch. Make
sure that the gap between the Magnet and the
Reed Switch is about 1/8". If necessary, loosen the
Screw (38), move the Reed Switch slightly, and then
retighten the Screw. Reattach the Hood (not shown),
and run the treadmill for a few minutes to check for a
correct speed reading.
20
4
1/8"
38
64
63
67
Top
View
PROBLEM: The walking belt slows when walked on
SOLUTION: a. Use only a single-outlet surge suppressor that meets all of the specifications described on page 11.
b. If the walking belt is overtightened, treadmill performance may decrease and the walking belt may become damaged. Remove the key and UNPLUG THE
POWER CORD. Using the hex key, turn both rear
roller bolts counterclockwise, 1/4 of a turn. When the
walking belt is properly tightened, you should be able
to lift each edge of the walking belt 2 to 3 inches off
the walking platform. Be careful to keep the walking
belt centered. Then, plug in the power cord, insert the
key, and run the treadmill for a few minutes. Repeat
until the walking belt is properly tightened.
b
2"–3"
Rear Roller Bolts
c. If the walking belt still slows when walked on, please see the front cover of this manual.
PROBLEM: The walking belt is off-center or slips when walked on
SOLUTION: a. If the walking belt is off-center, first remove the key
and UNPLUG THE POWER CORD. If the walking
belt has shifted to the left, use the hex key to turn
the left rear roller bolt clockwise 1/2 of a turn; if the
walking belt has shifted to the right, turn the left
bolt counterclockwise 1/2 of a turn. Be careful not to
overtighten the walking belt. Then, plug in the power
cord, insert the key, and run the treadmill for a few
minutes. Repeat until the walking belt is centered.
b. If the walking belt slips when walked on, first remove
the key and UNPLUG THE POWER CORD. Using
the hex key, turn both rear roller bolts clockwise, 1/4
of a turn. When the walking belt is correctly tightened,
you should be able to lift each edge of the walking
belt 2 to 3 inches off the walking platform. Be careful
to keep the walking belt centered. Then, plug in the
power cord, insert the key, and carefully walk on the
treadmill for a few minutes. Repeat until the walking
belt is properly tightened.
21
a
b
CONDITIONING GUIDELINES
WARNING:
Before beginning this
or any exercise program, consult your physician. This is especially important for individuals over the age of 35 or individuals with preexisting health problems.
The pulse sensor is not a medical device.
Various factors, including your movement,
may affect the accuracy of heart rate readings.
The sensor is intended only as an exercise aid
in determining heart rate trends in general.
The following guidelines will help you to plan your exercise program. For more detailed exercise information, obtain a reputable book or consult your physician.
EXERCISE INTENSITY
Whether your goal is to burn fat or to strengthen your
cardiovascular system, the key to achieving the
desired results is to exercise with the proper intensity.
The proper intensity level can be found by using your
heart rate as a guide. The chart below shows recommended heart rates for fat burning and aerobic exercise.
To find the proper heart rate for you, first find your age
near the bottom of the chart (ages are rounded off to
the nearest ten years). Next, find the three numbers
above your age. The three numbers define your “training zone.” The lower two numbers are recommended
heart rates for fat burning; the higher number is the
recommended heart rate for aerobic exercise.
Fat Burning
To burn fat effectively, you must exercise at a relatively
low intensity level for a sustained period of time.
During the first few minutes of exercise, your body
uses easily accessible carbohydrate calories for energy. Only after the first few minutes does your body
begin to use stored fat calories for energy. If your goal
is to burn fat, adjust the speed and incline of the treadmill until your heart rate is near the lowest number in
your training zone.
For maximum fat burning, adjust the speed and incline
of the treadmill until your heart rate is near the middle
number in your training zone.
Aerobic Exercise
If your goal is to strengthen your cardiovascular system, your exercise must be “aerobic.” Aerobic exercise
is activity that requires large amounts of oxygen for
prolonged periods of time. This increases the demand
on the heart to pump blood to the muscles, and on the
lungs to oxygenate the blood. For aerobic exercise,
adjust the speed and incline of the treadmill until your
heart rate is near the highest number in your training
zone.
WORKOUT GUIDELINES
Each workout should include the following three parts:
A Warm-up—Start each workout with 5 to 10 minutes
of stretching and light exercise. A proper warm-up increases your body temperature, heart rate and circulation in preparation for exercise.
Training Zone Exercise—After warming up, increase
the intensity of your exercise until your pulse is in your
training zone for 20 to 60 minutes. (During the first few
weeks of your exercise program, do not keep your
pulse in your training zone for longer than 20 minutes.)
Breathe regularly and deeply as you exercise—never
hold your breath.
A Cool-down—Finish each workout with 5 to 10 minutes of stretching to cool down. This will increase the
flexibility of your muscles and will help prevent postexercise problems.
EXERCISE FREQUENCY
To maintain or improve your condition, complete three
workouts each week, with at least one day of rest between workouts. After a few months, you may complete up to five workouts each week if desired. The key
to success is to make exercise a regular and enjoyable
part of your everyday life.
22
SUGGESTED STRETCHES
The correct form for several basic stretches is shown at the right. Move slowly as you stretch—never bounce.
1. Toe Touch Stretch
Stand with your knees bent slightly and slowly bend forward from
your hips. Allow your back and shoulders to relax as you reach
down toward your toes as far as possible. Hold for 15 counts, then
relax. Repeat 3 times. Stretches: Hamstrings, back of knees and
back.
1
2. Hamstring Stretch
Sit with one leg extended. Bring the sole of the opposite foot toward
you and rest it against the inner thigh of your extended leg. Reach
toward your toes as far as possible. Hold for 15 counts, then relax.
Repeat 3 times for each leg. Stretches: Hamstrings, lower back and
groin.
2
3. Calf/Achilles Stretch
With one leg in front of the other, reach forward and place your
hands against a wall. Keep your back leg straight and your back
foot flat on the floor. Bend your front leg, lean forward and move
your hips toward the wall. Hold for 15 counts, then relax. Repeat 3
times for each leg. To cause further stretching of the achilles tendons, bend your back leg as well. Stretches: Calves, achilles tendons and ankles.
3
4
4. Quadriceps Stretch
With one hand against a wall for balance, reach back and grasp one
foot with your other hand. Bring your heel as close to your buttocks
as possible. Hold for 15 counts, then relax. Repeat 3 times for each
leg. Stretches: Quadriceps and hip muscles.
5. Inner Thigh Stretch
Sit with the soles of your feet together and your knees outward. Pull
your feet toward your groin area as far as possible. Hold for 15
counts, then relax. Repeat 3 times. Stretches: Quadriceps and hip
muscles.
23
5
PART LIST—Model No. IMTL39606.2
Key No. Qty.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
1
30
1
8
2
1
6
2
1
1
5
2
1
1
2
1
4
2
4
4
4
2
1
2
1
1
6
1
1
1
1
2
4
2
2
1
4
13
5
1
2
1
1
4
2
2
4
1
Description
Hood
3/4" Screw
Left Foot Rail
Foot Rail Screw
Motor Tension Bolt
Motor Pivot Nut
6” Wire Tie
Motor Bolt
Drive Motor
Motor Bracket
Ground Screw
Power Bracket Star Washer
Power Cord Assembly
Reset/Off Circuit Breaker
Foot Rail Decal
Console Fan Assembly
Handrail Endcap
Handrail
Handrail Star Washer
Handrail Bolt
1/4" Star Washer
Console Bolt
Key/Clip
Frame Pivot Spacer
Console
Console Base
Upright Bolt/Wheel Bolt
Upright Wire
Latch Pin Assembly
Latch Housing
Left Upright
Frame Bolt
Frame Washer
Frame Spacer
Base Endcap
Right Upright
Base Pad
3/4" Tek Screw
Upright Star Washer
5/32" Hex Key
Caution Decal
Console Support Bracket
Warning Decal
Wheel Spacer
Wheel
Rear Bracket Screw
Nut
Base
Key No. Qty.
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
#
#
#
#
3
1
1
4
2
4
1
1
1
1
1
2
1
1
1
1
1
2
1
2
2
2
4
1
1
1
1
4
8
2
1
1
1
2
1
1
1
2
2
1
1
1
1
1
R1106A
Description
Plastic Tie
Belly Pan
Controller
U-Nut
Lift Frame Bolt
3/8" Nut
Lift Motor
Stop Bracket
Incline Motor Bolt, Top
Incline Motor Bolt, Bottom
Lift Frame
Motor Tension Nut
Motor Belt
Reed Switch
Clip
Front Roller/ Pulley
Motor Pivot Bolt
Platform Bolt, Front
Magnet
Belt Guide
Rear Roller Bracket
Isolator
Belt Guide Screw
Walking Belt
Walking Platform
Frame
Right Foot Rail
Platform Nut
Rear Roller Washer/Isolator Washer
Platform Bolt, Rear
Rear Roller
Right Rear Foot
3” Wire Tie
Rear Roller Bolt
Left Rear Foot
Ground Wire
Hex Key
Roller Bushing
Sliver Ground Screw
8” Wire Tie
4" Black Wire, M/F
8" Green Wire, F/R
4" Blue Wire, 2F
User’s Manual
#These parts are not illustrated
Specifications are subject to change without notice.
82
40
21
46
77
4
84
85
38
77
83
76
69
78
43
4
1
82
80
77
21
15
79
77
46
70
77
2
4
2
38
69
76
78
3
71
68
72
66
76
4
4
74
73
75
63
86
24
62
4
64
54
33
61
15
70
77
65
67
38
53
10
5
2
66
9
38
8
71
6
60
39
4
47
86
68
59
5
24
76
54
58
11
38
12
4
54
57
11
2
14
33
47
55
51
49
53
38
54
56
11
12
13
50
17
44
27
38
45
2
44
81
37
2
29
18
19
20
16
2
7
2
47
11
30
2
41
32
31
88
87
2
44
45
47
27
39
34
17
23
2
25
22
48
52
33
21
17
26
44
28
35
18
2
37
38
19
20
42
2
27
28
37
38
41
34
21
2
17
2
36
52
22
2
33
2
2
27
39
32
2
2
37
38
35
2
87
EXPLODED DRAWING—Model No. IMTL39606.2
R1106A
HOW TO ORDER REPLACEMENT PARTS
To order replacement parts, see the front cover of this manual. To help us assist you, please be prepared to give
the following information:
• the MODEL NUMBER of the product (IMTL39606.2)
• the NAME of the product (IMAGE 15.5 S treadmill)
• the SERIAL NUMBER of the product (see the front cover of this manual)
• the KEY NUMBER AND DESCRIPTION OF THE PART(S) (see the EXPLODED DRAWING and the PART
LIST attached in the center of this manual)
LIMITED WARRANTY
ICON Health & Fitness, Inc. (ICON) warrants this product to be free from defects in workmanship and
material, under normal use and service conditions. The drive motor is warranted for three (3) years after
the date of purchase. Parts and labor are warranted for ninety (90) days after the date of purchase.
This warranty extends only to the original purchaser. ICON's obligation under this warranty is limited to
replacing or repairing, at ICON's option, the product through one of its authorized service centers. All repairs for which warranty claims are made must be pre-authorized by ICON. If the product is shipped to a
service center, freight charges to and from the service center will be the customer’s responsibility. For inhome service, the customer will be responsible for a minimal trip charge. This warranty does not extend
to any product or damage to a product caused by or attributable to freight damage, abuse, misuse, improper or abnormal usage or repairs not provided by an ICON authorized service center; to products
used for commercial or rental purposes; or to products used as store display models. No other warranty
beyond that specifically set forth above is authorized by ICON.
ICON is not responsible or liable for indirect, special or consequential damages arising out of or in connection with the use or performance of the product or damages with respect to any economic loss, loss
of property, loss of revenues or profits, loss of enjoyment or use, costs of removal or installation or other
consequential damages of whatsoever nature. Some states do not allow the exclusion or limitation of incidental or consequential damages. Accordingly, the above limitation may not apply to you.
The warranty extended hereunder is in lieu of any and all other warranties and any implied warranties of
merchantability or fitness for a particular purpose is limited in its scope and duration to the terms set
forth herein. Some states do not allow limitations on how long an implied warranty lasts. Accordingly, the
above limitation may not apply to you.
This warranty gives you specific legal rights. You may also have other rights which vary from state to state.
ICON HEALTH & FITNESS, INC., 1500 S. 1000 W., LOGAN, UT 84321-9813
Part No. 247134 R1106A
Printed in Canada © 2006 ICON IP, Inc.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement