Linksys NMH300 - Media Hub Home Entertainment Storage User manual
Media Hub
Home Entertainment Storage
NMH Series (EU)
User Guide
About This Guide
Icon Descriptions
While reading through the User Guide you may see various icons that call attention to specific items. Below is a description of these icons:
NOTE:
This check mark indicates that there is a note of interest and is something that you should pay special attention to while using the product.
WARNING:
This exclamation point indicates that there is a caution or warning and it is something that could damage your property or product.
WEB:
This globe icon indicates a noteworthy website address or e-mail address.
Online Resources
Website addresses in this document are listed without
http:// in front of the address because most current web browsers do not require it. If you use an older web browser, you may have to add http:// in front of the web address.
Resource
Linksys
Linksys
International
Glossary
Website www.linksysbycisco.com
www.linksysbycisco.com/international www.linksysbycisco.com/glossary
Network Security www.linksysbycisco.com/security
Copyright and Trademarks
Specifications are subject to change without notice. Linksys, Cisco, and the Cisco logo are registered trademarks or trademarks of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Other brands are the trademarks or registered trademarks of their respective holders.
Mac and the Mac logo are trademarks of
Apple Computer, Inc., registered in the
U.S. and other countries. Copyright © 2009
Cisco Systems, Inc. All rights reserved.
Media Hub
About This Guide i
Media Hub
Table of Contents
Chapter 1: Product Overview 1
Front Panel of the Media Hub with LCD (NMH400 Series) . . . . . . . . . . . . . . . . . . . . 1
Front Panel of the Media Hub (NMH300 Series) . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Chapter 2: Getting Started 5
Chapter 3: Ways to Use the Media Hub 14
Chapter 4: Use of the Media Browser 18
Chapter 5: Use of the LCD Menu 33
Chapter 6: Windows File Backup (Windows only) 37
ii
Table of Contents
Chapter 7: Advanced Configuration 41
Appendix A: Troubleshooting 51
Appendix B: Specifications 55
Model NMH405 - Media Hub with LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55
Model NMH410 - Media Hub with LCD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56
Appendix C: Warranty Information 57
Appendix D: Regulatory Information 59
User Information for Consumer Products Covered by EU Directive 2002/96/EC on Waste
Appendix E: Software End User License Agreement 64
Media Hub iii
Chapter 1
Chapter 1:
Product Overview
Thank you for choosing the Linksys by Cisco Media Hub.
One Serial-ATA (SATA) hard disk is pre-installed (except for the NMH300 model), and a second SATA hard drive bay is available if you want to add more storage space. Use the
USB ports to add USB hard drives or connect USB flash drives to access your portable files. (USB hard drives may require external power supplies.) The Media Hub with LCD
(NMH400 Series) offers additional features, a LCD screen with navigation pad and memory card slots.
The front panel features vary for the NMH400 and NMH300
Series. The back panel and top panel features are the same for both series.
Front Panel of the Media Hub with LCD
(NMH400 Series)
Product Overview
OK
Navigation Pad
Use the navigation pad to navigate the LCD menus. Press the up or down arrow to move up or down the menu choices.
Press the right arrow to move to a lower menu level. Press the left arrow to move to a higher menu level.
To select a menu choice, press the OK button.
Refer to the end of this chapter for more information.
Power Button and LED
(Blue/Red) To power on the Media Hub, press the Power button.
To shut down the Media Hub, press and hold the button until the Power LED starts flashing
(this may take more than three seconds). A complete shutdown may take 10-15 seconds.
The Power LED flashes blue when the
Media Hub boots up, installs a disk, or shuts down. It is solidly lit blue when the Media
Hub is ready for use. The LED flashes either blue or red when there is an error. (Refer to
Appendix A: Troubleshooting, page 51.)
NOTE:
If the Media Hub must be shut down for a long period of time, Linksys recommends that you disconnect the power adapter from the Media Hub.
Secure Digital (SD) Memory Card Slot
Insert the SD, MultiMediaCard (MMC), extreme Digital
(xD), or Memory Stick (MS) card to access its files.
CompactFlash (CF) Memory Card Slot
Insert the CF memory card to access its files.
Media Hub
LCD Screen
When the Media Hub is powered on, the menu is displayed. Use it to initiate backup jobs, display status information, configure LCD screen settings, or power off the
Media Hub. Refer to Chapter 5: Use of the LCD
Menu, page 33 for more information.
USB
The USB port connects to a USB storage device.
1
Front Panel of the Media Hub (NMH300
Series)
Power Button and LED
(Blue/Red) To power on the Media Hub, press the Power button.
To shut down the Media Hub, press and hold the button until the Power LED starts flashing
(this may take more than three seconds). A complete shutdown may take 10-15 seconds.
The Power LED flashes blue when the
Media Hub boots up, installs a disk, or shuts down. It is solidly lit blue when the Media
Hub is ready for use. The LED flashes either blue or red when there is an error. (Refer to
Appendix A: Troubleshooting, page 51.)
NOTE:
If the Media Hub must be shut down for a long period of time, Linksys recommends that you disconnect the power adapter from the Media Hub.
USB
The USB port connects to a USB storage device.
Back Panel
Both series of the Media Hub share the same back panel.
DISK 1
(Blue/Red) The DISK 1 LED serves two purposes. The LED is solidly lit blue when Disk 1 is ready for use. The LED is not lit when no disk is detected.
DISK 2
(Blue/Red) The DISK 2 LED serves two purposes. The LED is solidly lit blue when Disk 2 is ready for use. The LED is not lit when no disk is detected.
Back Up Button To initiate backup jobs specified by the backup software on your computer(s), press the back up button.
NOTE:
The back up button only supports Windows computers installed with the backup software.
NOTE:
Your computer(s) must be powered on for the jobs to run.
Air Vent
The air vent allows air to circulate and cool the Media Hub.
WARNING:
Do not block the air vent on the back of the Media Hub; otherwise, overheating can occur.
Chapter 1
Security Slot
The security slot is where you can attach a lock to protect the Media Hub from theft.
USB
The USB port connects to a USB storage device.
Ethernet
The 10/100/1000 Gigabit Ethernet port connects to an Ethernet network device, such as a router or switch. The LED on the left lights up green when there is a 100 Mbps connection. It lights up orange when there is a 1000 Mbps connection. It does not light up when there is a 10 Mbps connection.
The amber LED on the right flashes when there is network activity.
Reset
To restore the factory default settings, press and hold the Reset button for three seconds. (User data on the hard disk(s) will not be affected.)
Power
The Power port connects to the included power adapter.
NOTE:
If the Media Hub must be shut down for a long period of time, Linksys recommends that you disconnect the power adapter from the Media Hub.
Top Panel
Both series of the Media Hub share the same top panel.
The drive bay cover protects the drive bays. Disk 1, a SATA hard disk, is pre-installed.
Product Overview
Install a Second Hard Disk
NOTE:
If you plan to install a second disk and mirror (RAID 1) these disks, then match disk sizes for maximum disk use. For more information about disk configuration options,
refer to Available Disk Configuration Actions,
To install a second SATA hard disk, follow these instructions:
1. To shut down the Media Hub, press and hold the Power button until the Power LED starts flashing.
2. Disconnect the power adapter from the Power port.
3. Disconnect the Ethernet network cable from the
Ethernet port.
4. To release the drive bay cover, push the button on the top panel.
5. To remove the empty drive bay, push together its clips and pull out the drive bay.
6. Make sure the screw holes of the hard disk line up with the screw holes of the drive bay. Then insert the hard disk into the drive bay.
7. Use the four included screws to secure the hard disk in its bay.
8. With the hard disk’s label facing the right side of the
Media Hub, slide the disk into the empty slot.
9. Push down on the hard disk to make sure the connectors are securely seated.
10. Lower the cover, and push it down to secure it.
11. Connect the Ethernet network cable to the Ethernet port.
12. Connect the power adapter to the Power port.
Replace a Hard Disk
WARNING:
The replacement hard disk must be blank with no partitions; otherwise, the Media
Hub cannot use it. (If you want to install a hard disk that was previously used in a Windows
computer, refer to Before You Begin, page 53.)
Media Hub
Button
Push the button to open the drive bay cover.
3
Chapter 1
To replace a hard disk, follow these instructions:
1. To shut down the Media Hub, press and hold the Power button until the Power LED starts flashing.
If this step does not shut down the Media Hub, then proceed to step 2.
2. Disconnect the power adapter from the Power port.
3. Disconnect the Ethernet network cable from the
Ethernet port.
4. To release the drive bay cover, push the button on the top panel.
5. To remove the hard disk you want to replace, push together the clips of its drive bay, and then pull out the drive bay.
6. Remove the hard disk from its drive bay.
7. To install the replacement hard disk, make sure the screw holes of the hard disk line up with the screw holes of the drive bay. Then insert the hard disk into the drive bay.
8. Use the four included screws to secure the hard disk in its bay.
9. With the hard disk’s label facing the right side of the
Media Hub, slide the drive bay back into its slot.
Product Overview
10. Push down on the hard disk to make sure the connectors are securely seated.
11. Lower the cover, and push it down to secure it.
12. Connect the Ethernet network cable to the Ethernet port.
13. Connect the power adapter to the Power port.
Media Hub
4
Chapter 2
Chapter 2: Getting Started
Overview
The Media Hub is designed to store your media content in one location for convenient access. (There are additional
ways to use the Media Hub; refer to Chapter 3: Ways to
The Media Hub offers three ways to help you copy files to the Media Hub. This chapter describes how to use the Media Importer, NTI Shadow (Windows only), and the Copy-and-Paste feature. (FTP is another option for copying files.)
You can copy media files from a computer or other network device. You can also copy media files from a USB storage device or memory card directly connected to the
Media Hub.
NOTE:
Only the Media Hub with LCD (NMH400
Series) supports direct connection of memory cards.
Media Importer
The Media Importer is the import tool that was automatically installed by the Setup Wizard. It supports most popular formats, such as mp3, jpg, and mpg files.
Use the Media Importer to automatically find, copy, and update media files to the Media Hub. In the future, any changes made or new files added will be automatically updated on the Media Hub.
Files using the following file formats and extensions are imported:
•
•
•
Music
.mp3, .wma, .m4a, .aac, .lpcm, .ogg, .flac, .ac3,
.mpa, .aif
Photos
.jpg, .png
Videos
.mpg, .mpeg, .mp4, .avi, .wmv, .divx, .3gp, .asf,
.xvid, .m1v, .m4v, .mov
If the Media Importer is not installed on your computer, run the Setup Wizard on the enclosed CD-ROM and click
Connect Computers.
Windows Media Importer
NOTE:
For Mac-specific information, refer to
Getting Started
Access
To access the Media Importer, double-click the system tray icon.
Importer System Tray Icon (Active)
Importer System Tray Icon (Offline or Disconnected)
If you do not see the icon, go to Start > All Programs >
Cisco Media Hub > Linksys Media Importer > Linksys
Media Importer.
System Tray Icon Menu
Right-click the system tray icon to view the following options:
Importer Icon Menu
Open
Click this option to open the Media Importer.
Go to Media Hub Online
Click this option to open the
Media Browser.
Media Importer Status
Click this option to view the status of the file transfers to the Media Hub.
Shutdown Linksys Media Importer
Click this option to exit the Media Importer.
About Linksys Media Importer
Click this option to view the version number of the Media Importer.
Main Menu
The main menu appears with the following options:
Media Hub
Media Importer Main Menu
Disconnect/Connect
Click this option to connect or disconnect the Media Hub from the Media Importer.
5
Chapter 2
Switch Media Hub
Click this option to switch to a different Media Hub.
Manage Media Importer
Click this option to select the folders you want to copy to the Media Hub.
Getting Started
To exit the Media Importer, click the X button in the upper right corner.
Mac Media Importer
If the Setup Wizard located on the CD-ROM does not run on your Mac, then download the Mac Setup Wizard from
www.linksysbycisco.com. Run the Mac Setup Wizard to install the Mac Media Importer.
Access
To access the Media Importer, double-click the icon on the menu bar in the upper right corner.
Importer System Tray Icon (Active)
Manage Media Importer
•
•
Choose the folders that will be regularly searched for media
Select the appropriate folders.
Only these types
Select the file types that will be copied.
The percentages and size of files by type (Photos/
Images, Music, and Video) are displayed.
To exit the Manage Media Importer screen, click Finish.
Media Importer Status
Click this option to view the status of the file transfers to the Media Hub.
Importer System Tray Icon (Offline or Disconnected)
If you do not see the icon, double-click the Macintosh
HD icon on your desktop. Go to Application > Media
Importer.
System Tray Icon Menu
Click the icon to view the following options:
Media Importer Status
•
•
•
•
Import Status
The number and size of files being imported are displayed.
Time Left
The amount of time left for the import and its speed are displayed.
Current Transfers
For each file, the % (percentage),
Folder, File name, Sent (size of imported data), and Size
(total size of file) are displayed.
Files imported in this session
For each file, the Time
Completed, Folder, File name, and Size are displayed.
To exit the Media Importer Status screen, click Close.
Media Hub
Importer Icon Menu
Open Manager Media Importer
Click this option to open the Media Importer.
Go to Media Hub Online
Click this option to open the
Media Browser.
Open Media Importer Status
Click this option to view the status of the file transfers to the Media Hub.
About Media Importer
Click this option to view the version number of the Media Importer.
Shutdown Media Importer
Click this option to exit the
Media Importer.
6
Chapter 2
Main Menu
The main menu appears with the following options:
Getting Started
Manage Importer Status
Click this option to view the status of the file transfers to the Media Hub.
Media Importer Main Menu
Disconnect/Connect
Click this option to connect or disconnect the Media Hub from the Media Importer.
Change Media Hub
Click this option to switch to a different Media Hub.
Manage Media Importer
Click this option to select the folders you want to copy to the Media Hub.
Manage Media Importer
•
•
(Folders)
Select the folders that will be regularly searched for media.
Only these
Select the file types that will be copied.
The percentages and size of files by type (Music,
Photos/Images, and Video) are displayed.
To exit the Manage Media Importer screen, click OK.
Media Importer Status
•
•
•
Import Status
The number and size of files being imported are displayed.
Time Left
The amount of time left for the import and its speed are displayed.
Current Transfers
For each file, the % (percentage),
Folder, File name, Sent (size of imported data), and Size
(total size of file) are displayed.
•
Files imported in this session
For each file, the Time
Completed, Folder, File name, and Size are displayed.
To exit the Media Importer Status screen, click the X button in the upper left corner.
To exit the Media Importer, click the X button in the upper left corner.
NTI Shadow (Windows only)
NTI Shadow is the backup software you installed during the Setup Wizard. Use it to automatically copy your documents to the Media Hub for safekeeping.
If you chose not to install the backup software, then NTI
Shadow will not be available. To install NTI Shadow, run the Setup Wizard on the enclosed CD-ROM and click
Connect Computers.
Access
Go to Start > All Programs > Cisco Media Hub > NTI
Shadow.
After you have accessed NTI Shadow for the first time, the system tray icon appears. Double-click the icon to access
NTI Shadow.
NTI Shadow System Tray
Media Hub
7
Chapter 2
System Tray Icon Menu
Right-click the system tray icon to view the following options:
NTI Shadow Icon Menu
Shadow Setting
Click this option to open NTI Shadow.
About NTI Shadow
Click this option to view the version number of NTI Shadow.
Exit
Click this option to exit NTI Shadow.
Main Menu
The main menu appears.
NTI Shadow Main Menu
Create Backup Job
Create Backup Job
Click this option to create a backup
job. For more information, refer to Create Backup Job,
Modify Backup Job
Backup jobs are listed in this section.
Default Backup Job
The Setup Wizard creates a default backup job that backs up specific files in the Documents folder. (This folder is named “Users” in Windows Vista or “Documents and
Settings” in Windows XP.)
These files include the following file types: document
(.doc, .docx, .xls, .xlsx, .pdf, .ppt, .txt, .htm, etc.) and .pptx.
The backup files are saved to the \backup\<Computer_
Name>\Documents folder on the Media Hub and are
Media Hub
Getting Started
organized by date. You can change the default backup job created by the Setup Wizard; for example, you can back up additional folders on your computer.
Options
Select the appropriate backup job, and then click one of the following options:
Start Backup
Click this option to start a backup job.
Edit
Click this option to change a backup job.
Disable
Click this option to disable a backup job.
Disable All
Click this option to disable all backup jobs.
Delete
Click this option to delete a backup job.
To exit NTI Shadow, click Done.
NOTE:
For more information about NTI Shadow, click Help.
Copy-and-Paste
Use the Copy-and-Paste feature to manually copy files to the Media Hub. Paste music to the music folder, photos to the photos folder, and videos to the videos folder.
NOTE:
File transfers may take minutes or hours, depending on file transfer speeds and the number and size of your files. File transfer speeds will vary, depending on network conditions, including use of wireless.
Instructions to Copy Media Files to the Media Hub
Follow these guidelines:
•
•
•
•
Copy files of a single file type together at one time.
For example, copy music files at one time; do not copy music, photo, and video files at the same time.
Copy music files to the media\music folder of the
Media Hub.
Copy photo files to the media\photos folder of the
Media Hub.
Copy video files to the media\videos folder of the
Media Hub.
NOTE:
The files you copy to the Media Hub can be accessed by all users of the Media Hub.
8
Chapter 2
Windows Access
NOTE:
For Mac-specific information, refer to
1. To open Windows Explorer, go to Start > Programs
> Accessories > Windows Explorer. (You can also right-click Start and click Explore.)
2. During the Setup Wizard, you created a Friendly Name or device name for the Media Hub.
In the Address field of Windows Explorer, enter the Friendly Name of the Media Hub:
\\<Friendly_Name> (Example: \\mediahub)
Friendly Name
3. Press Enter.
You can also use the drive letter or IP address to access the
Media Hub.
NOTE:
The drive letter is mapped directly to the media folder, which holds the music, photos, and videos sub-folders. Use the Friendly Name or IP address of the Media Hub to access the backup and media folders.
Drive Letter
During the Setup Wizard, the Media Hub was assigned a drive letter to identify it on your computer.
Windows Vista
Right-click Start. Click Computer, and then click the drive letter to access the media folder of the Media Hub.
Windows XP
Double-click My Computer, and then click the drive letter to access the media folder of the Media Hub.
Drive Letter Not Found
If you do not see a drive letter for the Media Hub, run the Setup Wizard on the enclosed CD and click Connect
Computers. You can also follow these instructions:
1. To open Windows Explorer, go to Start > Programs
> Accessories > Windows Explorer. (You can also right-click Start and click Explore.)
2. Right-click My Computer (Windows XP) or Computer
(Windows Vista).
3. Select Map Network Drive.
Media Hub
Getting Started
4. In the Folder field, enter \\<Friendly_Name>\media.
5. Click Finish.
For additional information, refer to Windows Help.
NOTE:
If you do not see the Media Hub, then change the Workgroup of the Media Hub to match the Workgroup of your computer (refer
IP Address (For Advanced Users)
1. In the Address field of Windows Explorer, enter the IP address of the Media Hub:
\\<xxx.xxx.xxx.xxx>
IP Address of Media Hub
2. Then press Enter.
NOTE:
For the Media Hub with LCD (NMH400
Series), look up its IP address through the LCD
menu. Refer to Status, page 38. For the Media
Hub (NMH300 Series), look up its IP address through the router’s browser-based utility.
Refer to the router’s documentation for more information.
File Directory
Open the folders of the Media Hub. Use Windows Explorer to add, copy, move, or delete files.
Media Hub Accessed Through Friendly Name
9
Chapter 2
Getting Started
Media Folder of Media Hub Accessed Through Drive Letter
Mapped Drive
You can map any folder of the Media Hub as a separate drive.
1. To open Windows Explorer, go to Start > Programs
> Accessories > Windows Explorer. (You can also right-click Start and click Explore.)
2. Right-click Computer (Windows Vista) or My
Computer (Windows XP).
3. Select Map Network Drive.
4. From the Drive drop-down menu, select an available drive letter.
5. In the Folder field, enter the following:
\\<Friendly_Name_of_Media_Hub>\<folder_
name>. (Example: \\mediahub\backup.)
6. Click Finish.
Device Folder
If you have a USB storage device or memory card directly connected to the Media Hub, you can access it through the Media Hub.
If you accessed the Media Hub through its Friendly
Name or IP address, the name of the USB storage device or memory card is displayed. Double-click the name to access its files.
USB Storage Device Accessed Through Friendly Name
If you accessed the Media Hub through its drive letter, go to media > devices > mnt. The name of the USB storage device or memory card is displayed. Double-click the name to access its files.
USB Storage Device Accessed Through Drive Letter
Import Folder
The media\import folder stores the data imported from USB storage devices or memory cards. The data is organized by the date of the data import.
Media Hub
Data Imported from USB Storage Device
10
Chapter 2
Backup Folder
The backup folder stores the data backed up from USB storage devices or memory cards. The data is organized by the date of the data backup.
NOTE:
Use the Friendly Name or IP address of the Media Hub to access the backup folder.
3. Go to Edit > Paste.
Getting Started
Data Backed Up from USB Storage Device
NOTE:
You can map the backup folder as a
separate drive. Refer to Mapped Drive, page
Example Showing How to Copy Media Files to the
Media Hub
The following example describes the instructions to copy music files to the media\music folder of the Media Hub.
Use similar instructions to copy the other types of files, photo or video.
1. In Windows Explorer, select the music files on your computer or other network device. Then go to Edit >
Copy.
NOTE:
If you have a USB storage device or memory card directly connected to the
Media Hub, then its device name is displayed.
Double-click the device name to access its files.
2. Open the media\music folder of the Media Hub.
Copy Music Files to Media Hub
The music files are copied to the media\music folder; this may take minutes or hours, depending on file transfer speeds and the number and size of your files. File transfer speeds will vary, depending on network conditions, including use of wireless.
NOTE:
Additional information about Windows
Explorer is available in Windows Help.
WEB:
For more information about the Media
Hub, refer to the rest of the User Guide. You can also visit www.linksysbycisco.com/support, and select the Media Hub.
Mac Access
1. To open the Finder, double-click the Macintosh HD icon on your desktop.
2. During the Setup Wizard, you created a Friendly
Name or device name for the Media Hub. In the Shared section, the Media Hub is listed as its Friendly Name. (Example: MediaHub)
Double-click the Media Hub.
Friendly Name
Media Hub
11
Chapter 2
File Directory
Open the folders of the Media Hub. Use the Finder to add, copy, move, or delete files.
Getting Started
Import Folder
The media\import folder stores the data imported from USB storage devices or memory cards. The data is organized by the date of the data import.
Media Hub Accessed Through Friendly Name
Data Imported from USB Storage Device
Backup Folder
The backup folder stores the data backed up from USB storage devices or memory cards. The data is organized by the date of the data backup.
Media Folder of Media Hub Accessed Through Friendly Name
Device Folder
If you have a USB storage device or memory card directly connected to the Media Hub, you can access it through the Media Hub.
If you accessed the Media Hub through its Friendly
Name or IP address, the name of the USB storage device or memory card is displayed. Double-click the name to access its files.
USB Storage Device Accessed Through Friendly Name
Media Hub
Data Backed Up from USB Storage Device
Example Showing How to Copy Media Files to the
Media Hub
The following example describes the instructions to copy music files to the media\music folder of the Media Hub.
Use similar instructions to copy the other types of files, photo or video.
1. In the Finder, select the music files on your computer or other network device. Then go to Edit > Copy.
NOTE:
If you have a USB storage device or memory card directly connected to the
Media Hub, then its device name is displayed.
Double-click the device name to access its files.
2. Open the media\music folder of the Media Hub.
12
Chapter 2
3. Go to Edit > Paste.
Copy Music Files to Media Hub
The music files are copied to the media\music folder; this may take minutes or hours, depending on file transfer speeds and the number and size of your files. File transfer speeds will vary, depending on network conditions, including use of wireless.
WEB:
For more information about the Media
Hub, refer to the rest of the User Guide. You can also visit www.linksysbycisco.com/support, and select the Media Hub.
Getting Started
Media Hub
13
Chapter 3
Chapter 3: Ways to Use the
Media Hub
Overview
This chapter describes how you can use the Media Hub:
•
•
•
• centralized storage digital media sharing on-demand backups automatic backup of your computers
Centralized Storage
The Media Hub is designed to store and share files for your network. Most people use Windows Explorer or the Finder to manage the files of the Media Hub.
If the Remote Access service
†
is enabled, then use the File
Browser for remote access of the Media Hub. (FTP is another option.) For more information about how to configure the
remote access settings, refer to Remote Access, page 47.
Ways to Use the Media Hub
Local Access
Media files are typically stored on different computers and other network devices throughout the house. You can copy all of the media files to the Media Hub, so your media content is stored in one location for convenient access.
Plus you have backup copies of your media files.
The Media Hub offers three ways to help you copy files to the Media Hub:
•
• the Media Importer
NTI Shadow (Windows only)
• the Copy-and-Paste feature
For more information, refer to Chapter 2: Getting Started,
Remote Access
If you enable and set up the Remote Access service, you can use the Media Hub over the Internet. For more information about how to configure the remote access
settings, refer to Remote Access, page 47. Use the
File Browser to add, copy, move, or delete files. Refer to
Remotely access your media and data files over the Internet
Internet
Automatic or on-demand backups
View pictures on any computer
Wireless Broadband
Router
Media Hub
Watch videos on your big-screen TV or listen to music on your home entertainment sound system
Digital Media Adapter
Diagram Showing the Media Hub
†
A period of Remote Access is included from date of activation.
Fees may apply thereafter and are subject to change. Go to
www.linksysbycisco.com for further information and details of terms and conditions applicable to the Remote Access service.
Media Hub
14
Chapter 3
Digital Media Sharing
The Media Hub automatically indexes the digital media files it stores, so you can use a web browser to access them through the Media Browser.
Media Browser
Media Browser
After you have copied media files to the Media Hub, use the Media Browser screen to access your home entertainment:
•
•
Play music
View photos
• Watch videos
• Manage media files
The Media Browser also lets you access devices directly connected to the Media Hub.
USB Storage Devices
Both models of the Media Hub support USB storage devices.
You can connect USB storage devices to the USB ports at any time. All folders and files on these devices are available while the USB storage devices are connected to the Media
Hub. Refer to Copy-and-Paste, page 8.
Memory Cards
Only the Media Hub with LCD (NMH400 Series) supports direct connection of memory cards. All folders and files on these cards are available while the memory cards are
inserted into the Media Hub. Refer to Copy-and-Paste,
Local Access
You can access the Media Browser screen from any computer using a web browser. For more information,
refer to Chapter 4: Use of the Media Browser, page 18.
Media Hub
Ways to Use the Media Hub
UPnP AV Media Server
If you have UPnP AV-enabled (or DLNA-certified) devices in your home, then you can use the Media Hub as a media server. (This service is enabled by default—no special setup required.) Such devices include digital media adapters and other devices, such as a gaming console with a built-in media player or digital picture frame.
For example, if you have a digital media adapter that sends content to your entertainment system, then the digital media adapter can locate the Media Hub using the UPnP
AV standard. Media content on the Media Hub can then be accessed and played by the digital media adapter.
By default, the Media Hub automatically indexes the digital media files it stores. You have the option of indexing media files on your local network. If you use this option, the Media Hub scans its local content and any media content stored in UPnP AV-compatible servers connected
to the local network. Refer to Media Server, page 49.
iTunes Server
If you use iTunes, then you can use the Media Hub as a centralized location for your iTunes library. (This service is enabled by default—no special setup required.) Open iTunes on any of the computers on your network, and play any music file on the Media Hub.
NOTE:
In iTunes, the Media Hub is displayed in the Shared section. If it is not displayed, enable iTunes to look for shared libraries. Go to Edit >
Preferences > Sharing. Select Look for shared
libraries. Click OK.
Remote Access
If you enable and set up the Remote Access service, you can use the Media Hub over the Internet. For more information about how to configure the remote access
settings, refer to Remote Access, page 47.
With the Remote Access service, you can access media files through the Media Browser. Use the File Browser to
add, copy, move, or delete files. Refer to File Browser,
Here are a few examples of remote access:
View Pictures Remotely
You want to share pictures from your recent trip, but you forgot to bring the memory card you used. This is not a problem since you have set up your Media Hub for remote access.
1. On your friends’ computer, open the web browser.
2. Go to http://www.ciscomediahub.com.
15
Chapter 3
3. Enter the remote device name of your Media Hub, and then click Go.
4. Enter the administrative or Guest Password. (The administrative Password allows full access to the Media
Hub; the Guest Password allows access restricted to the media content of the Media Hub and is set up through the Configuration utility). Click Submit.
5. On the Media Browser screen, click Photos. Navigate to the trip pictures.
Now you can view a slideshow of your trip pictures.
Download Videos Remotely
You want to share videos from your recent trip, but they are stored on your Media Hub. Fortunately, you can access your Media Hub over the Internet.
1. On your friends’ computer, open the web browser.
2. Go to http://www.ciscomediahub.com.
3. Enter the remote device name of your Media Hub, and then click Go.
4. Enter the administrative or Guest Password. (The administrative Password allows full access to the Media
Hub; the Guest Password allows access restricted to the media content of the Media Hub and is set up through the Configuration utility). Click Submit.
5. On the Media Browser screen, click File Browser.
6. Navigate to the trip videos. Then click the Download
to PC option .
Now you can download the videos to your friends’ computer.
NOTE:
Playing video files over remote access requires the same plug-ins you have installed on your home computer. Video playback support over remote access depends on the broadband speeds of both your home connection and remote connection. Video playback should be limited to smaller video files, as larger video files may take a long time to load and play.
Ways to Use the Media Hub
NOTE:
The Media Hub plays video content through a browser plug-in. Download and install your favorite media player to enable video playback within the Media Browser.
Please note that media players have varying levels of support for different video formats.
If the video format you want to play is not supported, you may want to search the
Internet for a media player that can run on your computer and support the desired video formats. (Make sure you download the latest version.) Some suggested players include
QuickTime, VLC, and Windows Media Player.
For more information about video support, visit
http://www.linksysbycisco.com/support.
Upload Pictures Remotely
Your relatives have pictures from a recent family reunion.
The pictures are too large in size to send to your home e-mail address, so you decide to upload them to your
Media Hub.
1. On your relatives’ computer, open the web browser.
2. Go to http://www.ciscomediahub.com.
3. Enter the remote device name of your Media Hub, and then click Go.
4. Enter the administrative or Guest Password. (The administrative Password allows full access to the Media
Hub; the Guest Password allows access restricted to the media content of the Media Hub and is set up through the Configuration utility). Click Submit.
5. On the Media Browser screen, click File Browser. Then click the Upload to Media Hub option .
Now you can upload the photos to your Media Hub.
Setup of Remote Access Feature
When you enable and set up the remote access feature, keep the following in mind:
•
Every Media Hub has a unique Remote Device Name. If the name you want to use is already taken, then try an alternate name for your Media Hub.
•
For remote access, open your web browser. Go to
http://www.ciscomediahub.com. When prompted, enter the Remote Device Name and administrative or
Guest Password of your Media Hub.
For more information, refer to Remote Access, page 47.
Media Hub
16
Chapter 3
On-Demand Backups
Computers (Windows only)
NTI Shadow is the backup software you installed during the Setup Wizard. During installation, the Setup Wizard creates a default backup job with the “On Demand” option selected. (The default backup job also runs automatically.)
If you have backup jobs with the “On Demand” option selected, then you can use the on-demand backup feature of the Media Hub; for more information, refer to
For the Media Hub (NMH300 Series), you can press the back up button on the front panel to initiate backup jobs.
For the Media Hub with LCD (NMH400 Series), you can use
the LCD menu to initiate backup jobs; refer to Backup,
USB Storage Devices
Both models of the Media Hub support direct connection of USB storage devices. You can use the Media Browser to
import media files; refer to Devices, page 20.
When you connect a USB storage device to the Media Hub with LCD (NMH400 Series), the LCD menu will ask if you want to import media files; click the OK button to confirm.
You can also use Windows Explorer or the Finder to access the USB storage device. Then you can copy files to the
Media Hub. Refer to Copy-and-Paste, page 8.
Memory Cards
Only the Media Hub with LCD (NMH400 Series) supports direct connection of memory cards.
When you insert a memory card, the LCD menu will ask if you want to import media files; click the OK button to confirm.
You can use the Media Browser to import media files; refer
Windows Explorer or the Finder is another alternative; use it to access the memory card. Then you can copy files to
the Media Hub. Refer to Copy-and-Paste, page 8.
Automatic Backup of Computers
(Windows only)
NTI Shadow is the backup software you installed during the Setup Wizard. During installation, the Setup Wizard creates a default backup job, which runs automatically.
Media Hub
NOTE:
Your computer(s) must be powered on for the jobs to run.
Ways to Use the Media Hub
(The default backup job also enables the “On Demand” option.)
Default Backup Job
The Setup Wizard creates a default backup job that backs up specific files in the My Documents folder.
These files include the following file types: document
(.doc, .docx, .xls, .xlsx, .pdf, .ppt, .txt, .htm, etc.) and .pptx.
The backup files are saved to the \backup\<Computer_
Name>\Documents folder on the Media Hub and are organized by date. You can change the default backup job created by the Setup Wizard; for example, you can back up additional folders on your computer.
Additional Backup Jobs
You can set up additional, automatic backup jobs. For
instructions, refer to Create Backup Job, page 37.
17
Chapter 4
Chapter 4: Use of the
Media Browser
This chapter describes the Media Browser, which is used to access your music, photos, and videos.
How to Access the Media Hub
You can use Windows Explorer, the Finder, or your web browser to access the Media Hub. For more information
about Windows Explorer or the Finder, refer to Copy-and-
You can access the Media Browser via a web browser on a local computer connected to your router. Double-click the desktop icon that was created during the Setup Wizard.
(If you enable and set up the Remote Access service, you
can use the Media Hub over the Internet. Refer to Remote
Access Instructions, page 48.)
Use of the Media Browser
NOTE:
For the Media Hub with LCD (NMH400
Series), look up its IP address through
the LCD menu. Refer to Status, page 34.
For the Media Hub (NMH300 Series), look up its
IP address through the router’s browser-based utility. Refer to the router’s documentation for more information.
3. If you do not have Adobe Flash Player (version 10 or higher) installed, you will be prompted to install it.
Follow the on-screen instructions. (An active Internet connection is required.)
The Media Browser screen of the browser-based utility appears.
Media Hub Desktop Icon
You can also follow these instructions:
1. Open your web browser.
2. Windows: In the Address field, enter one of the following:
http://<Friendly_Name>(example: http://mediahub) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press Enter.
Mac: In your web browser, enter one of the following:
http://<Friendly_Name>.local (example: http://mediahub.local) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press return.
NOTE:
The Friendly Name is the name you created during the Setup Wizard. If you did not create a Friendly Name, use the default; enter http://mediahub (Windows) or
http://mediahub.local (Mac).
Media Browser
How to Use the Media Browser
Use the Media Browser screen to access your home entertainment:
•
•
Play music
View photos
•
Watch videos
The Media Hub scans for music, photos, and videos.
This activity may take several hours the first time the scan occurs, depending on the number of media files.
Subsequent scans for updates will take less time.
The Media Browser screen displays thumbnail images of files found in the music, photos, videos, and import folders of the Media Hub (it will not display thumbnail images of sub-folders).
NOTE:
The files you copy to the Media Hub can be accessed by all users of the Media Hub.
Media Hub
18
Chapter 4
You have these options:
Configuration
Access advanced settings through this
option. Refer to Chapter 7: Advanced Configuration,
Re-Scan
Refresh the Media Hub’s index of media files.
Search
Use this option to search your files by keyword.
? (User Guide)
To access the online version of this User
Guide, click ? or Help (if displayed). (An active Internet connection is required.)
! (Message Center)
To access the notification messages, click Messages. If this option is not displayed, then the
Message Center has no notification messages. Refer to
Media Browser > Configuration, Re-Scan, Search, ? (User Guide),
! (Message Center)
Music
Click this option to access your music files. Refer to
Photos
Click this option to access your photo files. Refer
Videos
Click this option to access your video files. Refer
File Browser
Click this option to access the Media Hub’s
folder directory and manage your media files. Refer to File
Media Browser > Music, Photos, Videos, File Browser
Recent Music
The files with the most recent file dates are displayed.
To add a song to the playlist, select it. Then click the Add
to Playlist button .
To play a song, select it. Then click the Play button .
NOTE:
The Media Hub’s built-in music player only supports the mp3, wma, and m4a audio format. Other files will open in the default player for the files’ specific file extension(s).
Use of the Media Browser
Media Browser > Recent Music, Photos, Videos
NOTE:
The Media Hub uses an online service to retrieve metadata such as album title, artist name, album cover art. No information about your music collection is stored by the online service. If you want to add your own custom artwork to a song or album, you can use an ID3 editor (available through an online search).
Recent Photos
The files with the most recent file dates are displayed. To view a photo, select it. Then click the View Photo button
.
To start a slideshow, select a photo. Then click the Play button .
NOTE:
The Media Hub’s built-in viewer only supports the jpeg format. Other files will open in the default viewer for the files’ specific file extension(s).
Recent Videos
The files with the most recent file dates are displayed. To play a video, select it. Then click the Play button .
NOTE:
The Media Hub plays video content through a browser plug-in. Download and install your favorite media player to enable video playback within the Media Browser. Please note that media players have varying levels of support for different video formats. If the video format you want to play is not supported, you may want to search the Internet for a media player that can run on your computer and support the desired video formats. (Make sure you download the latest version.) Some suggested players include
QuickTime, VLC, and Windows Media Player.
For more information about video support, visit
http://www.linksysbycisco.com/support.
Media Hub
19
Chapter 4
Disk Space
The amounts of used, available, and total disk space of the
Media Hub are displayed.
Use of the Media Browser
Devices
For the selected device, the amounts of used, available, and total storage space are displayed.
Media Browser > Disk Space, USB, Memory Cards
USB
The Media Browser screen displays the number of USB storage devices directly connected to the Media Hub. You can connect USB storage devices to the USB ports at any time. All folders and files on these devices are available while the USB storage devices are connected to the Media
Hub.
NOTE:
Detection of a new USB storage device or memory card may take up to one minute.
Double-click the USB icon to access status information or import media files. The Devices screen appears. Refer to
NOTE:
If you need to remove a USB storage device that is connected to the Media Hub, use the Eject option on the Devices screen before physically removing the storage device; otherwise, the storage device may seem to be present after it has been physically removed
(also known as a ghosting issue).
Memory Cards
Only the Media Hub with LCD (NMH400 Series) supports direct connection of memory cards.
The Media Browser screen displays the number of memory cards directly connected to the Media Hub. All folders and files on these cards are available while the memory cards are inserted into the Media Hub.
Double-click the memory card icon to access status information or import media files. A new screen appears.
Devices
Import Media
To copy the media files on the device to the Media Hub, click this option.
Importing
When the import is complete, click OK.
Eject
The Eject option readies the Media Hub for safe removal of the selected device. Before you physically remove the device, click this option. (Using the Eject option is strongly recommended for proper removal of
USB storage devices.)
Cancel
To cancel a function or exit the Device screen, click this option.
Other Devices
Click the left or right arrow button to scroll through the other devices.
Cancel
To exit the Devices screen, click this option.
Media Hub
20
Chapter 4
Search
Enter the keyword, and then click the magnifying glass button. The Search Results screen appears.
Use of the Media Browser
Videos
To view your video files, click the Videos icon.
File Browser
To access the Media Hub’s folder directory and manage your media files, click the File Browser icon.
Message Center
The Media Hub uses the Message Center to notify you of new firmware and other changes.
# new messages/# total messages
The number of new messages and number of total messages are displayed.
Show: All, New, or Read
To display all messages, select
All. To display only new messages, select New. To display only read messages, select Read.
Delete All Messages
To delete all messages, click this option.
Date
The date of the message is displayed.
Subject
The subject of the message is displayed.
To read a message, select it. The message is displayed below the list.
To delete a message, click the corresponding X button.
Search Results
Use Search Results
Search results for
The keyword is displayed.
The search results are listed in a table with the following options and information:
Add to Playlist
To add an album or song to the playlist, click the Add to Playlist button . (Available for music only.)
Play in External Application
To use the computer’s external player, click the Play in External Application button . (Available for songs and videos only.)
View Photo
To use the Media Hub’s built-in viewer, click the View Photo button . (Available for photos only.)
Play
To use the Media Hub’s built-in player or start a slideshow, click the Play button .
Thumbnail
A thumbnail of the photo or associated image is displayed.
Name/Title
The name of the file is displayed.
Type
The file type is displayed.
Date
The date when the file was last saved is displayed.
Size
The size of the file is displayed.
Info
Descriptive information is displayed.
The initial search automatically includes music, photo, and video files.
Navigation
Four icons are displayed at the top of the screen.
Home
To return to the Media Browser screen at any time, click the Home icon.
Music
To view your music files, click the Music icon.
Photos
To view your photo files, click the Photos icon.
Media Hub
Message Center
Click the X button in the upper right corner to exit the
Message Center screen.
21
Chapter 4
Music
After you click the Music option, the Music screen appears.
View your music files by category:
•
•
Album
Artist
• Recent
• Song
The thumbnail view is automatically displayed. At the bottom right of the screen, the number of pages is listed.
Use the slider to move from page to page.
For a list with details, click the list view button at the bottom left of the screen.
Use of the Media Browser
•
•
•
•
•
Timer
The timer shows the duration of the song played and the duration of the rest of the song.
Volume
To mute the sound, click the speaker icon.
Click it again to resume the sound. To change the volume level, use the volume slider.
Shuffle Playlist
To shuffle the songs on the playlist, click the Shuffle Playlist button.
Repeat Playlist
To repeat the songs on the playlist in a continuous loop, click the Repeat Playlist button.
Clear Playlist
To clear the playlist of all songs, click the Clear Playlist button.
To display the playlist, click the down arrow. The song title and duration of each song are displayed. To minimize the playlist, click the up arrow.
To return to the Media Browser screen at any time, click the Home icon. To switch to photos, click the Photos icon.
To switch to videos, click the Videos icon. To access the
Media Hub’s folder directory and manage your media files, click the File Browser icon.
Album
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the album you want.
Music > Album (Thumbnail View)
When you are viewing any music category, select the album or song you want.
Add to Playlist
To add an album or song to the playlist, click the Add to Playlist button.
Play
To play the music, click the Play button.
NOTE:
The Media Hub’s built-in music player only supports the mp3, wma, and m4a audio format. Other files will open in the default player for the files’ specific file extension(s).
A new screen opens with the name of the song displayed.
•
•
•
Previous
To move to the previous song on the playlist, click the Previous button.
Pause/Play
Click the button to pause the song. Click it again to resume.
Next
To move to the next song on the playlist, click the Next button.
Media Hub
Music > Play
Music > Album (List View)
Thumbnail View
Each album displays its album name and artist name.
Add to Playlist
To add an album to the playlist, click the
Add to Playlist button.
Play
To play the music, click the Play button.
List View
The albums are listed in a table with the following options and information:
Add to Playlist
To add an album to the playlist, click the
Add to Playlist button.
Play
To play the music, click the Play button.
22
Chapter 4
Album
The name of the album is displayed.
Artist Name
The name of the artist is displayed.
Genre
The genre of the song is displayed.
For more information about an album, double-click its thumbnail or name (list view).
Use of the Media Browser
Music > Album Close-Up (Song Tracks View)
Album Close-Up
The names of the album and artist are displayed.
Play Entire Album
To play all songs, click the Play button.
Add to Playlist
To add the album to the playlist, click the
Add to Playlist button.
The song tracks are listed in order.
Add to Playlist
To add a song to the playlist, click the
Add to Playlist button.
Play in External Application
To play the music using an external player, click the Play in External Application button. (The external player is the default music player application on your computer.)
Play
To play the music using the Media Hub’s built-in player, click the Play button.
#
The track number is displayed. Click the up or down arrow to change the track order (ascending or descending).
Song
The title of the song is displayed.
Duration
The duration of the complete song is displayed.
Click Back to return to the Album screen.
Artist
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the artist you want.
Music > Artist (Thumbnail View)
Thumbnail View
Each artist displays an album thumbnail and artist name.
Add to Playlist
To add music by an artist to the playlist, click the Add to Playlist button.
Play
To play the music, click the Play button.
List View
The artists are listed in a table with the following options and information:
Add to Playlist
To add music by an artist to the playlist, click the Add to Playlist button.
Play
To play the music, click the Play button.
Artist Name
The name of the artist is displayed.
Recent
The files with the most recent file dates are displayed.
Media Hub
Music > Recent (List View)
Thumbnail View
Each song displays its title, artist name, and album name.
Add to Playlist
To add a song to the playlist, click the
Add to Playlist button.
23
Chapter 4
Play in External Application
To play the music using an external player, click the Play in External Application button. (The external player is the default music player application on your computer.)
Play
To play the music, click the Play button.
List View
The songs are listed in a table with the following options and information:
Add to Playlist
To add a song to the playlist, click the
Add to Playlist button.
Play in External Application
To play the music using an external player, click the Play in External Application button. (The external player is the default music player application on your computer.)
Play
To play the music using the Media Hub’s built-in player, click the Play button.
Song
The title of the song is displayed.
Album
The name of the album is displayed.
Artist Name
The name of the artist is displayed.
Genre
The genre of the song is displayed.
Duration
The duration of the complete song is displayed.
Song
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the song you want.
Use of the Media Browser
Play
To play the music, click the Play button.
List View
The songs are listed in a table with the following options and information:
Add to Playlist
To add a song to the playlist, click the
Add to Playlist button.
Play in External Application
To play the music using an external player, click the Play in External Application button. (The external player is the default music player application on your computer.)
Play
To play the music using the Media Hub’s built-in player, click the Play button.
Song
The title of the song is displayed.
Album
The name of the album is displayed.
Artist Name
The name of the artist is displayed.
Genre
The genre of the song is displayed.
Duration
The duration of the complete song is displayed.
Loc
The location of the song is displayed.
Photos
After you click the Photos option, the Photos screen appears. View your photo files by category:
•
•
Album
Date
• Name
• Recent
The thumbnail view is automatically displayed. At the bottom right of the screen, the number of pages is listed.
Use the slider to move from page to page.
For a list with details, click the list view button at the bottom left of the screen.
Music > Song (Thumbnail View)
Thumbnail View
Each song displays its title, artist name, and album name.
Add to Playlist
To add a song to the playlist, click the
Add to Playlist button.
Play in External Application
To play the music using an external player, click the Play in External Application button. (The external player is the default music player application on your computer.)
Media Hub
Photos > Album (Thumbnail View)
24
Chapter 4
When you are viewing any photo category, select the album or photo file you want.
NOTE:
The Media Hub’s built-in viewer supports the jpeg format. Other files will open in the default viewer for the files’ specific file extension(s).
For most selections, you have two options, View Photo and Play.
View Photo
To view a photo, click the View Photo button.
Photos > View Photo
A new screen opens. The name of the photo is displayed.
Options are listed at the bottom of the screen.
•
•
•
Previous
Click the Previous (left arrow) button to view the previous photo.
Play
To begin a slideshow, click the Play button.
Next
Click the Next (right arrow) button to view the next photo.
Click the X button to exit the screen.
Play
To begin a slideshow, click the Play button.
The slideshow automatically begins. Click the screen to display thumbnails and options at the top of the screen.
Mouse over a photo to display a larger thumbnail, or click a photo to display it within your web browser.
Use of the Media Browser
Options are listed at the top of the screen and are described below starting on the left of the screen.
•
Previous Page
Click the Previous Page (left arrow) button to view the previous page of photos.
•
•
Scroll Left
Click the scroll left (bracket) button to scroll through the photos to the left.
Scroll Right
Click the scroll right (bracket) button to scroll through the photos to the right.
•
•
Next Page
Click the Next Page (right arrow) button to view the next page of photos.
Slidebar
Click and then move the slidebar to change the display duration; select 2, 5, 10, 30, or 60 Seconds
Delay.
•
•
•
•
Pause/Play
Click the button to pause the photo on display. Click it again to resume the slideshow.
Enter Full Screen
Click the Enter Full Screen button to display the slideshow on the entire screen. Click this button again or press ESC to exit full screen mode.
Transitions
Select Transitions to enable the transition effect between photos.
Close Show
Click the Close Show (X) button to return to the Photos screen.
If the options disappear, click anywhere on the screen to make the options reappear.
To return to the Media Browser screen at any time, click the Home icon. To switch to music, click the Music icon.
To switch to videos, click the Videos icon. To access the
Media Hub’s folder directory and manage your media files, click the File Browser icon.
Album
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the album you want.
Media Hub
Photos > Slideshow
Photos > Album (Thumbnail View)
Thumbnail View
Each album displays its name and date.
25
Chapter 4
Play
To begin a slideshow, click the Play button.
List View
The albums are listed in a table with the following option and information:
Play
To begin a slideshow, click the Play button.
Photo-Album
The name of the album is displayed.
For more information about an album, double-click its thumbnail or name (list view).
Use of the Media Browser
Date
The months are displayed at the top of the screen. Click the month of the photos you want. Select the appropriate year from the drop-down menu to the right of the calendar months.
Photos > Album Close-Up (List View)
Album Close-Up
The photos are in alphabetical order.
Thumbnail View
Each photo displays its date, name, and album name.
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
The photos are listed in alphabetical order.
List View
The photos are listed in a table with the following options and information:
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
Date
The date when the photo was last saved is displayed.
Photo
The name of the photo is displayed.
Photo-Album
The name of the album is displayed.
Size
The size of the file is displayed.
Dimension
The dimensions in width by height (in pixels) are displayed.
Loc
The location of the photo is displayed.
Click Back to return to the Album screen.
Media Hub
Photos > Date (List View)
Thumbnail View
Each photo displays its date, name, and album name.
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
List View
The photos are listed in a table with the following options and information:
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
Date
The date when the photo was last saved is displayed.
Photo
The name of the photo is displayed.
Photo-Album
The name of the album is displayed.
Size
The size of the file is displayed.
Dimension
The dimensions in width by height (in pixels) are displayed.
Loc
The location of the photo is displayed.
26
Chapter 4
Name
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the photo you want.
Use of the Media Browser
Photos > Name (List View)
Thumbnail View
Each photo displays its date, name, and album name.
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
List View
The photos are listed in a table with the following option and information:
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
Date
The date when the photo was last saved is displayed.
Photo
The name of the photo is displayed.
Photo-Album
The name of the album is displayed.
Size
The size of the file is displayed.
Dimension
The dimensions in width by height (in pixels) are displayed.
Loc
The location of the photo is displayed.
Recent
The files with the most recent file dates are displayed.
Photos > Recent (Thumbnail View)
Thumbnail View
Each photo displays its date, name, and album name.
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
List View
The photos are listed in a table with the following option and information:
View Photo
To view the photo, click the View Photo button.
Play
To begin a slideshow, click the Play button.
Date
The date when the photo was last saved is displayed.
Photo
The name of the photo is displayed.
Photo-Album
The name of the album is displayed.
Size
The size of the file is displayed.
Dimension
The dimensions in width by height (in pixels) are displayed.
Media Hub
27
Chapter 4
Videos
After you click the Videos option, the Videos screen appears
View your video files by category:
•
Name
•
Recent
The thumbnail view is automatically displayed. For a list with details, click the list view button at the bottom of the screen.
Use of the Media Browser
•
•
Volume
To mute the sound, click the speaker icon.
Click it again to resume the sound. To change the volume level, use the volume slider.
Pause/Play
Click the button to pause the video. Click it again to resume.
•
Stop
Click the Stop button to stop the video.
Click the X button to exit the screen.
To return to the Media Browser screen at any time, click the Home icon. To switch to music, click the Music icon.
To switch to photos, click the Photos icon. To access the
Media Hub’s folder directory and manage your media files, click the File Browser icon.
Name
The alphabet is displayed at the top of the screen. Click the letter that starts the name of the video you want.
Videos > Name (Thumbnail View)
When you are viewing any video category, select the video file you want.
Play in External Application
To play a video using an external player, click the Play in External Application button. (The external player is the default video application on your computer.)
Play
To play a video, click the Play button.
NOTE:
The Media Hub plays video content through a browser plug-in. Download and install your favorite media player to enable video playback within the Media Browser. Please note that media players have varying levels of support for different video formats. If the video format you want to play is not supported, you may want to search the Internet for a media player that can run on your computer and support the desired video formats. (Make sure you download the latest version.) Some suggested players include
QuickTime, VLC, and Windows Media Player.
For more information about video support, visit
http://www.linksysbycisco.com/support.
A new screen opens. The name of the video is displayed.
Options are listed at the bottom of the screen.
•
Slidebar
Use the video slider to move forward or backward in the video.
Media Hub
Videos > Name (List View)
Thumbnail View
Each video displays its title, duration, and size.
Play in External Application
To play a video using an external player, click the Play in External Application button. (The external player is the default video application on your computer.)
Play
To play a video, click the Play button.
List View
The videos are listed in a table with the following options and information:
Play in External Application
To play a video using an external player, click the Play in External Application button. (The external player is the default video application on your computer.)
Play
To play a video using the Media Hub’s built-in player, click the Play button.
Video
The name of the video is displayed.
Type
The type of video is displayed.
28
Chapter 4
Date
The date when the video was last saved is displayed.
Size
The size of the file is displayed.
Duration
The duration of the video is displayed.
Loc
The location of the video is displayed.
Recent
The files with the most recent file dates are displayed.
Use of the Media Browser
File Browser
Use the File Browser option to access the Media Hub’s folder directory and manage your media files.
NOTE:
With the File Browser, you have access to the Media Hub only. To copy files from your computer to the Media Hub, use Windows
Explorer or the Finder. Refer to Copy-and-
After you click the File Browser option, the password screen appears.
Videos > Recent (Thumbnail View)
Thumbnail View
Each video displays its title, duration, and size.
Play in External Application
To play a video using an external player, click the Play in External Application button. (The external player is the default video application on your computer.)
Play
To play a video, click the Play button.
List View
The videos are listed in a table with the following options and information:
Play in External Application
To play a video using an external player, click the Play in External Application button. (The external player is the default video application on your computer.)
Play
To play a video using the Media Hub’s built-in player, click the Play button.
Video
The name of the video is displayed.
Type
The type of video is displayed.
Date
The date when the video was last saved is displayed.
Size
The size of the file is displayed.
Duration
The duration of the video is displayed.
Loc
The location of the video is displayed.
Media Hub
Password Screen
Enter the password you created during the Setup Wizard
(the default is admin). Click Submit.
To open the appropriate folder, use the Directory Tree the same way you would use Windows Explorer or the Finder.
When you mouse over an icon, the tooltip displays its function.
File Browser > Media Hub > Media > Photos
The files are listed with the following information: Name,
Size, Type of file, and Modified by date.
File and folder options are listed above the list of files.
Page options are listed below the list of files. Refer to Page
29
Chapter 4
NOTE:
If you need to remove a USB storage device that is connected to the Media Hub, use the Eject option on the Devices screen before physically removing the storage device; otherwise, the storage device may seem to be present after it has been physically removed (also known as a ghosting issue). For
instructions, refer to USB, page 20.
File and Folder Options
To manage your files and folders, use the following options:
Refresh file list
Click this option to update the list.
Delete File
Select a file, and then click this option. (To select multiple files, use ctrl + click or shift + click.) On the Delete screen, click Yes to delete the file.
Use of the Media Browser
NOTE:
When you copy files, there is a maximum size of 2 GB for each individual file, and there is a maximum size of 3 GB for multiple files (copied at one time). Windows Explorer, the Finder, or
FTP should be used to copy larger files.
Move File
Select a file, and then click this option. (To select multiple files, use ctrl + click or shift + click.) On the Select Destination screen, select the location for the move, and then click Move File(s).
Delete File
NOTE:
When you delete files, there is a maximum size of 2 GB for each individual file, and there is a maximum size of 70 GB for multiple files (deleted at one time). Windows
Explorer, the Finder, or FTP should be used to delete larger files.
Copy File
Select a file, and then click this option. (To select multiple files, use ctrl + click or shift + click.) On the Select Destination screen, select the location for the copy, and then click Copy File(s).
Move File > Select Destination
NOTE:
When you move files, there is a maximum size of 2 GB for each individual file, and there is a maximum size of 3 GB for multiple files (copied at one time). Windows Explorer, the Finder, or
FTP should be used to move larger files.
Rename File
Select a file, and then click this option. On the Rename File or Folder screen, enter the new name, and then click Submit.
Rename File or Folder
New Folder
Click this option to create a new folder. On the New Folder screen, enter the name, and then click
Submit.
Copy File > Select Destination
New Folder
Media Hub
30
Chapter 4
Delete Folder
Select a folder, and then click this option.
On the Delete screen, click Yes to delete the folder.
Use of the Media Browser
Delete Folder
NOTE:
When you delete a folder, there is a maximum size of 70 GB. Windows Explorer, the
Finder, or FTP should be used to delete larger folders.
Copy Folder
Select a folder, and then click this option.
On the Select Destination screen, select the location for the copy, and then click Copy Folder.
Move Folder > Select Destination
NOTE:
When you move a folder, there is a maximum size of 3 GB. Windows Explorer, the
Finder, or FTP should be used to move larger folders.
Rename Folder
Select a folder, and then click this option.
On the Rename File or Folder screen, enter the new name, and then click Submit.
Copy Folder > Select Destination
NOTE:
When you copy a folder, there is a maximum size of 3 GB. Windows Explorer, the
Finder, or FTP should be used to copy larger folders.
Move Folder
Select a folder, and then click this option.
On the Select Destination screen, select the location for the move, and then click Move Folder.
Rename File or Folder
Download to PC
Select a file, and then click this option.
On the Download File screen, click Download File.
Media Hub
Download File
NOTE:
The Download File screen may appear differently, depending on your web browser.
Upload to Media Hub
Click this option to upload files to the Media Hub. The Upload Files screen appears.
•
Browse
Click this option to select files.
•
•
Remove
To remove a file from the upload list, select the file, and then click this option.
Remove All
To remove all files from the upload list, click this option.
31
Chapter 4
•
The upload list displays File name, File Type, and File
Size for all files.
Upload
To upload files to the Media Hub, click this option.
Use of the Media Browser
Upload to Media Hub
Page Options
To display a different page of files, use one of the following options:
First Page
Click this option to display the first page of files.
Previous Page
Click this option to display the previous page of files.
Page _ of <Total_Pages>
Enter the number of the page you want to display.
Next Page
Click this option to display the next page of files.
Last Page
Click this option to display the last page of files.
Media Hub
File Browser > Media Hub > Media > Photos
32
Chapter 5
Chapter 5: Use of the
LCD Menu
This chapter describes functions of the LCD menu, which is only featured on the Media Hub with LCD (NMH400
Series). Use the LCD menu to do the following:
•
•
• initiate backup jobs for computer(s) running the
backup software (Refer to NTI Shadow, page 37 for
more information.) back up or import files from your USB storage device or memory card to the Media Hub display status information for the Media Hub
NOTE:
For the IP address of the Media Hub, go to Status > Network.
•
• configure LCD screen settings power off the Media Hub
Use of the LCD Menu
• While the Media Hub is booting up, press the OK button to boot backup firmware from the hard drive.
To display the main menu, press the OK button.
•
How to Access the LCD Menu
After the Media Hub is powered on and boots up, the main menu is displayed and offers these options:
Backup
Select this option to initiate computer or device backup jobs.
Status
Select this option to view space, usage, or network information.
Settings
Select this option to configure the screensaver or backlight settings. You can also upgrade the firmware of the Media Hub.
Power Off
Select this option to power off the Media
Hub.
Main Menu
If the screensaver with the Friendly Name is displayed, press the OK button to activate the LCD menu.
Media Hub with LCD (NMH400 Series)
How to Navigate the LCD Menu
Use the navigation pad to navigate the LCD menus. Press the up or down arrow to move up or down the menu choices. Press the right arrow to move to a lower menu level. Press the left arrow to move to a higher menu level.
The OK button has three functions:
• To select a menu choice, press the OK button.
Media Hub
Screensaver
Backup
The Backup screen allows you to copy files from your computers or devices to the Media Hub.
Backup
33
Chapter 5
PC Backup
Select this option to initiate backup jobs specified by the backup software on your computer. (Your computer must be powered on for the jobs to run.)
NOTE:
The PC Backup option only supports
Windows computers installed with the backup software.
Use of the LCD Menu
Copying Data
PC Backup
After the Media Hub sends the backup message to your computer, click OK to return to the Backup menu.
NOTE:
The Setup Wizard automatically installs backup software on your computer to run backup jobs (unless you choose not to install
it); refer to NTI Shadow, page 37. If you have
installed the backup software, then you can use the computer backup feature of the Media Hub.
Device Backup
To back up a device directly connected to the Media Hub, select Device Backup.
NOTE:
You can directly connect USB storage devices to both series of the Media Hub. Only the Media Hub with LCD (NMH400 Series) supports direct connection of memory cards.
On the Device Backup screen, select the device you want to back up.
Device Backup
After all files have been copied to the Media Hub, click OK to return to the Backup menu.
Backup data is saved to the media/backup folder, which organizes the data by the date of the data backup. Refer
Status
The Status screen allows you to display information about the Media Hub.
Status
Space
Select this option to view the amounts of used, available, and total memory.
Device Backup
Space
Press the left arrow to return to the Status menu.
Media Hub
34
Chapter 5
Usage
Select this option to view the percentages of the
Media Hub used by Music, Photos, Videos, and Other media.
Use of the LCD Menu
Screensaver
Select this option to configure the wait time before the screensaver activates.
Usage
Press the left arrow to return to the Status menu.
Network
Select this option to view the status of the
Internet connection, status of the Local Area Network
(LAN) connection, and local IP address of the Media Hub.
Screensaver
•
•
•
•
Never
If you never want to use the screensaver, select this option.
5 seconds
If you want the screensaver to activate after five seconds of LCD inactivity, select this option.
30 seconds
If you want the screensaver to activate after 30 seconds of LCD inactivity, select this option.
1 minute
If you want the screensaver to activate after one minute of LCD inactivity, select this option.
Press the left arrow to return to the Settings menu.
Backlight
Select this option to configure the duration of the backlight for the LCD screen.
Network
•
•
Internet
The icon is green if there is a connection to the Internet. It is red if there is no connection.
LAN
The icon is green if there is a connection to the local network. It is red if there is no connection.
•
IP Address
You can use the local IP address of the
Media Hub to access its browser-based utility. Refer
to Chapter 7: Advanced Configuration, page 41 for
more information.
Press the left arrow to return to the Status menu.
Settings
The Settings screen allows you to configure the LCD screen settings. You can also upgrade the firmware of the Media
Hub.
Backlight
•
•
Never
If you never want to use the backlight, select this option.
5 seconds
If you want the backlight to last five seconds, select this option.
•
•
30 seconds
If you want the backlight to last
30 seconds, select this option.
1 minute
If you want the backlight to last one minute, select this option.
Press the left arrow to return to the Settings menu.
Settings
Media Hub
35
Chapter 5
Firmware
Select this option to view the version numbers of the current and latest firmware. You can also upgrade the firmware of the Media Hub.
Use of the LCD Menu
New Device Alert
On the Alert screen, click Yes to copy media files of the new device to the Media Hub, or click No to cancel.
Firmware
•
•
•
Current version
The version number of the current firmware is displayed.
Latest version
The version number of the latest available firmware is displayed.
Update
Click Update to upgrade the firmware to the latest version available.
WARNING:
Do not reboot or power off the
Media Hub during the firmware upgrade.
Press the left arrow to return to the Settings menu.
Power Off
The Power Off screen allows you to power off the Media
Hub from the front panel.
Import Device Content
If you clicked Yes, then the Media Hub will copy media files of the new device to the Media Hub.
Importing
Power Off
Click Yes to confirm the power-off, or click No to cancel.
Alerts
The LCD menu also displays informative alert messages.
This section describes the possible messages.
New Device Alert
A new device is connected to the Media Hub. Click OK.
Data Import Done
After the media files have been copied, click OK.
Import data is saved to the media/import folder, which organizes the data by the date of the data import. Refer to
NOTE:
To back up all files of the new device,
refer to Backup, page 33. (The Import option
only copies media files.)
Media Hub
36
Chapter 6
Chapter 6: Windows File
Backup (Windows only)
Overview
This chapter describes how to back up files to the Media
Hub. NTI Shadow is the backup software you installed during the Setup Wizard. You can initiate on-demand backup jobs or set up automatic backup jobs to automatically copy your documents to the Media Hub for safekeeping.
(If you did not choose to install the backup software, then
NTI Shadow will not be available. To install NTI Shadow, run the Setup Wizard on the enclosed CD-ROM and click
Connect Computers.)
NOTE:
This chapter applies only to Windows computers installed with the backup software.
NTI Shadow
Access
Go to Start > All Programs > Cisco Media Hub > NTI
Shadow.
After you have accessed NTI Shadow for the first time, the system tray icon appears. Double-click the icon to access
NTI Shadow.
File Backup
NTI Shadow Main Menu
Create Backup Job
Create Backup Job
Click this option to create a backup
job. Follow the instructions in the section, Create Backup
Modify Backup Job
Backup jobs are listed. Options are described in the
section, Modify Backup Job, page 39.
Create Backup Job
1. After you have clicked Create Backup Job, the Select
Folders/Files screen appears. Select the folders and files you want to back up. Then click Next.
NTI Shadow System Tray
System Tray Icon Menu
Right-click the system tray icon to view the following options:
NTI Shadow Icon Menu
Shadow Setting
Click this option to open NTI Shadow.
About NTI Shadow
Click this option to view the version number of NTI Shadow.
Exit
Click this option to exit NTI Shadow.
Main Menu
The main menu appears.
Media Hub
Create Backup Job
37
Chapter 6
2. Click Browse to select the Media Hub.
File Backup
•
Save your folder/file changes every
Select this option to start a backup job according to the schedule you specify. Select On Demand if you want to start the backup job using the Backup feature on the Media
Hub (refer to On-Demand Backup, page 40 for more
information).
Then click Next.
Where & When to Back up
3. Click Computer or My Computer. Select the Media
Hub, and then select the folder you want. (The backup folder is recommended.)
To create a folder, click Make New Folder. Enter a name.
Then click OK.
Where & When to Back up
5. Select one of the following save options:
•
Save all the previous file versions
Select this option if you want to save all previous versions.
•
•
Save a limited number of previous versions
Select this option if you want to save the number of previous versions you specify.
Do not save any previous file versions
Select this option if you do not want to save any previous versions.
Then click Next.
Browse For Folder
4. Select one of the following schedule options:
•
On Demand (Only)
Select this option to start a backup job manually, either through NTI Shadow or
the Backup feature on the Media Hub (refer to On-
Demand Backup, page 40 for more information).
•
•
Save your folder/file changes to the backup destination every time you save changes to your
PC
Select this option to start a backup job every time incremental changes are made to your folders or files.
Save your folder/file changes every
Select this option to start a backup job as often as you specify in minutes, hours, or days. Select On Demand if you want to start the backup job using the Backup feature
on the Media Hub (refer to On-Demand Backup, page
Media Hub
File Versions
38
Chapter 6
6. Review the settings. To change the settings, click Back.
If the settings are correct, click Finish to save the backup job.
Backup Job Summary
7. To start your backup job now, click Yes. Otherwise, click No.
Start Backup
8. NTI Shadow will save your backup job. Click OK.
Save Your Backup Job
9. The new backup job is now listed in the Modify Backup
Job section.
Media Hub
NTI Shadow Main Menu
File Backup
Modify Backup Job
Backup jobs are listed in this section.
Default Backup Job
The Setup Wizard creates a default backup job that backs up specific files in the Documents folder. (This folder is named “Users” in Windows Vista or “Documents and
Settings” in Windows XP.)
These files include the following file types: document
(.doc, .docx, .xls, .xlsx, .pdf, .ppt, .txt, .htm, etc.) and .pptx.
The backup files are saved to the \backup\<Computer_
Name>\Documents folder on the Media Hub and are organized by date. You can change the default backup job created by the Setup Wizard; for example, you can back up additional folders on your computer.
Options
Select the appropriate backup job, and then click one of the following options:
Start Backup
Click this option to start a backup job.
Edit
Click this option to change a backup job.
Disable
Click this option to disable a backup job.
Disable All
Click this option to disable all backup jobs.
Delete
Click this option to delete a backup job.
To exit NTI Shadow, click Done.
NOTE:
For more information about NTI Shadow, click Help.
Backup Jobs
On-demand and automatic backup options are available.
Before you can run a backup job, check the following:
•
•
Your computer(s) must be powered on for the jobs to run.
The backup software must be installed on every computer you want to back up.
NOTE:
The backup options of the Media Hub only support Windows computers installed with the backup software.
Automatic Backup
For automatic backups, use the backup software to create and schedule automatic backup jobs. Make sure you set the backup destination to be the Media Hub. Refer to
39
Chapter 6
On-Demand Backup
There are three ways to initiate a backup job using the
Media Hub:
•
•
LCD menu (Media Hub with LCD, NMH400 Series) back up button (Media Hub, NMH300 Series)
• browser-based utility (both series of the Media Hub)
You can also use the backup software to initiate a backup job.
NOTE:
When you set up the options of your backup job through the backup software, make sure the “On Demand” option is selected.
Follow the instructions for the method you want to use.
Backup Using LCD Menu
The LCD menu is available on the Media Hub with LCD
(NMH400 Series).
1. If the screensaver is displayed, press the OK button to activate the LCD menu.
2. On the Main Menu, select Backup.
File Backup
4. After the Media Hub sends the backup message to your computer, click OK to return to the Backup menu.
PC Backup
Back Up Button
The back up button screen is available on the Media Hub
(NMH300 Series).
To initiate backup jobs specified by the backup software on your computer, press the back up button.
Main Menu
3. Select PC Backup to initiate backup jobs specified by the backup software on your computer(s).
Back Up Button
Both Series of the Media Hub
1. Access the browser-based utility of the Media Hub.
(Refer to Chapter 7: Advanced Configuration, page
2. On the Media Browser screen, click Configuration.
3. Enter your password, and then click Submit.
4. Click the Backup tab.
5. Click Backup to initiate backup jobs specified by the backup software on your computer(s).
Backup
Backup
Media Hub
40
Chapter 7
Chapter 7:
Advanced Configuration
NOTE:
When first installing the Media Hub, you should use the Setup Wizard on the Setup
CD-ROM. If you want to configure advanced settings, use this chapter.
After setting up the Media Hub with the Setup Wizard
(located on the CD-ROM), it is ready for use. If you want to change its advanced settings, use the Configuration utility. This chapter describes each web page of the utility and each page’s key functions. You can access the utility via a web browser on a local computer connected to your router. (If you enable and set up the Remote Access service, you can use the Media Hub over the Internet.
Refer to Remote Access Instructions, page 48.)
NOTE:
If the Configuration utility of your Media
Hub displays different options, please upgrade its firmware. For more information, refer to
How to Access the Configuration Utility
To access the Media Hub from any computer using a web browser, double-click the desktop icon that was created during the Setup Wizard.
Advanced Configuration
NOTE:
The Friendly Name is the name you created during the Setup Wizard. If you did not create a Friendly Name, use the default; enter http://mediahub (Windows) or
http://mediahub.local (Mac).
NOTE:
For the Media Hub with LCD (NMH400
Series), look up its IP address through
the LCD menu. Refer to Status, page 34.
For the Media Hub (NMH300 Series), look up its IP address through the router’s web-based utility. Refer to the router’s documentation for more information.
3. If you do not have Adobe Flash Player (version 10 or higher) installed, you will be prompted to install it.
Follow the on-screen instructions. (An active Internet connection is required.)
4. The Media Browser screen of the browser-based utility appears. Click Configuration.
Media Hub Desktop Icon
You can also follow these instructions:
1. Open your web browser.
2. Windows: In the Address field, enter one of the following:
http://<Friendly_Name>(example: http://mediahub) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press Enter.
Mac: In your web browser, enter one of the following:
http://<Friendly_Name>.local (example: http://mediahub.local) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press return.
Media Hub
Media Browser Screen
NOTE:
For more information about the Media Browser screen, refer to
Chapter 4: Use of the Media Browser, page 18.
5. The password screen appears. Enter the password you created during the Setup Wizard (the default is
admin). Click Submit.
Password Screen
41
Chapter 7
The Overview screen appears.
Advanced Configuration
Disk
The amounts of used, available, and total disk space are displayed.
View Details
Click this option to view more information.
Services
The Media Hub supports Remote Access, Windows File
Sharing, Media Server, iTunes Server, and FTP Server.
Configure Services
Click this option to access service
settings. Refer to Services, page 47.
System
Configure the system and network settings. You can also upgrade the Media Hub’s firmware or remotely reboot it.
Overview
Overview
On the Overview screen, five tabs are available. To access the System, Disk, Backup, or Services screen, click the appropriate tab. To return to the Overview screen, click the
Overview tab. To refresh the on-screen information, click
Refresh.
The Overview screen displays information about the Media
Hub and configuration options.
Search
Use this option to search your files by keyword.
? (User Guide)
To access the online version of this User
Guide, click ? or Help (if displayed). (An active Internet connection is required.)
! (Message Center)
To access the notification messages, click Messages. If this option is not displayed, then the
Message Center has no notification messages. Refer to
Overview > Search, ? (User Guide), ! (Message Center)
To return to the Media Browser screen at any time, click the
house icon. To switch to photos, click the Photos icon.
To switch to videos, click the Videos icon. To access the
Media Hub’s folder directory and manage your media files, click the File Browser icon.
System
The name and local IP address of the Media Hub are displayed.
Configure System
Click this option to access system
settings. Refer to System, page 42.
Media Hub
System
Hostname
The hostname of the Media Hub is displayed.
Workgroup
The workgroup name of the Media Hub is displayed.
MAC Address
The MAC address of the Media Hub is displayed.
Serial Number
The serial number of the Media Hub is displayed.
Model
The model number of the Media Hub is displayed.
Firmware Version
The version number of the firmware is displayed.
Media Browser Software Version
The version number of the Media Browser software is displayed.
42
Chapter 7
Up Time
The number of minutes the Media Hub has been running is displayed.
Media Hub Name
The name of the Media Hub is displayed.
Workgroup
The name of the workgroup is displayed.
Change
Click this option to change the name and/or workgroup.
Advanced Configuration
•
•
•
Subnet Mask
Enter the subnet mask of the Media
Hub.
Gateway
Enter the IP address of the gateway.
DNS Server 1
Enter the IP address of the DNS server.
•
DNS Server 2
Enter the IP address of the backup DNS server.
Click Submit to save your changes, or click Cancel to cancel your changes.
Password
The Password protects administrative access to the Media Hub, including full access to the Configuration utility and the File Browser. The Password must have between 1 to 32 characters and use only letters, numbers, or punctuation (do not use any spaces).
Change
Click this option to change the Password.
Change System Name
•
•
Media Hub Name
Enter the new name.
Workgroup
Enter the new workgroup name.
Click Submit to save your changes, or click Cancel to cancel your changes.
IP Address
The local IP address of the Media Hub is displayed.
Change
Click this option to change the network settings.
Change Password
•
•
•
Current Password
Enter the current Password.
New Password
Enter the new Password.
Confirm New Password
Enter the new Password again to confirm it.
Click Submit to save your change, or click Cancel to cancel your change.
Guest Password The Guest Password allows access restricted to the media content of the Media Hub (no access to the Configuration utility or the File Browser). The
Guest Password must have between 1 to 32 characters and use only letters, numbers, or punctuation (do not use any spaces).
Change
Click this option to change the Guest Password.
IP/DNS Configuration
•
•
Enable DHCP
If you want to allow your network router to assign a dynamic IP address to the Media
Hub, select this option. (It is enabled by default.)
If you disable the DHCP server feature, then you configure static network settings:
IP Address
Enter the local IP address you want to assign to the Media Hub.
NOTE:
If you change the IP address, you may have to re-assign the drive letter to the Media
Hub. Run the Setup Wizard on the enclosed
CD-ROM (click Connect Computers), or refer to
Windows Help for instructions on how to assign a drive letter to the Media Hub.
Media Hub
Change Guest Password
•
•
Password
Enter the new password.
Confirm New Password
Enter the new password again to confirm it.
43
Chapter 7
Click Submit to save your change, or click Cancel to cancel your change.
System Date
The current date and time of the Media
Hub are displayed.
Time Zone
The current time zone of the Media Hub is displayed.
Change
Click this option to assign a different time zone to the Media Hub.
Change System Date
•
•
Current Media Hub Date
The current date and time are displayed.
Time Zone
Select the appropriate geographic region, and then select the appropriate city, county, or community.
Click Submit to save your changes, or click Cancel to cancel your changes.
Device Language
The current language of the LCD is based on your computer’s operating system.
NOTE:
This option only applies to the Media
Hub with LCD (NMH400 Series).
Change
Click this option to switch the LCD of the Media
Hub to a different language.
Advanced Configuration
Update Firmware
The Media Hub will search for the latest version.
Click Update to begin the firmware update, or click
Cancel to cancel the update.
WARNING:
Do not reboot or power off the
Media Hub during the firmware upgrade, which may take up to 15 minutes.
Restart
If you want to reboot the Media Hub, click
Restart.
Reboot Device
Click Yes to reboot the Media Hub, or click No to cancel the reboot.
Select Language
•
Select Language
Select the appropriate language.
Click Submit to save your change, or click Cancel to cancel your change.
Firmware Update: Latest Firmware Version
The latest available firmware version of the Media Hub is displayed.
Update
Click this option to update the firmware.
NOTE:
An active Internet connection is required.
Media Hub
44
Chapter 7
Disk
Access the disk usage information and disk configuration settings, which will vary depending on the number of disks installed.
Disk (One Hard Disk Installed)
Disk (Two Hard Disks Installed)
Disk Usage by Type
The percentages of the disk used by Music, Photos, Videos, and Other media are displayed.
Media Hub
Advanced Configuration
Disk Usage by Space
The amounts of used, available, and total disk space are displayed.
Current Disk Configuration
Disk 1/Disk 2 (if installed)
Vendor
The manufacturer of the hard disk is displayed.
Model
The model number of the hard disk is displayed.
Health
The status of the hard disk is displayed.
RAID Mode
The disk configuration mode is displayed.
Linear 1 is the single disk mode. If two hard disks are installed, the options are Linear 2 (Increase Space) and
RAID 1 (Increase Protection).
RAID Status
The status of the disk configuration: OK,
DEGRADED, or DEAD, is displayed.
Slot A
Slot A is the drive bay on the left when you view the front panel of the Media Hub. If Disk 1 is installed, its status: OK, BAD, or NEW, is displayed. If Disk 1 is not installed, the status is EMPTY.
Slot B
Slot B is the drive bay on the right when you view the front panel of the Media Hub. If Disk 2 is installed, its status: OK, BAD, or NEW, is displayed. If Disk 2 is not installed, the status is EMPTY.
Available Disk Configuration Actions
If one disk is installed, then only the Revert to single disk option is available.
If two disks are installed, then two options for disk configuration, Increase Space and Increase Protection, are available. Increase Protection: RAID 1 helps protect data. Increase Storage: Linear 2 increases the amount of available storage. Linksys recommends Increase
Protection: RAID 1 for most users. (To install a second hard
disk, refer to Install a Second Hard Disk, page 3.)
? Disk Configuration Help
Click this option to access the following:
•
Overview
View general information about disk configuration.
•
•
•
Add/Replace Drive
Follow the instructions to add or replace a disk.
Configuration
View information about the available disk configuration options.
Recovery
Follow the instructions if a disk fails.
NOTE:
Linksys does not support data recovery after hard disk failure.
45
Chapter 7
? Increase Space
(available only for two installed disks)
To maximize storage space, click this option, also known as Linear 2 mode. Total capacity is equal to the capacity of the two hard disks. For more information, click the ? icon.
When prompted to confirm the new disk configuration, click Yes to continue, or click No to cancel.
WARNING:
For the Increase Space: Linear 2 mode, if one of the two hard disks fails, then all data will be lost.
Before you click this option, review the following:
•
•
•
The Media Hub is designed to maintain existing data during disk configuration; however, Linksys recommends that you back up its data to your computer or an external hard disk before you continue.
When you set the Media Hub to the Increase Space:
Linear 2 mode, the Media Hub will be unavailable for approximately 15 minutes and then automatically reboot.
Do not manually reboot or power off the Media Hub during this time.
• After reboot, available disk space will increase to the total size of both hard disks.
? Increase Protection
(available only for two installed disks) To help enhance data reliability, click this option, also known as RAID 1 mode. Disk 2 holds a copy of the data on Disk 1. For more information, click the ? icon.
When prompted to confirm the new disk configuration, click Yes to continue, or click No to cancel.
NOTE:
For the Increase Protection: RAID 1 mode,
Disk 2 must be equal to or larger in size than
Disk 1. If one disk is smaller, only the smaller size will be used for this mode.
Before you click this option, review the following:
•
•
•
The Media Hub is designed to maintain existing data during disk configuration; however, Linksys recommends that you back up its data to your computer or an external hard disk before you continue.
When you set the Media Hub to the Increase Protection:
RAID 1 mode, the Media Hub will be unavailable for approximately 15 minutes and then automatically reboot.
After reboot, the Media Hub will synchronize the data on the two disks.
Advanced Configuration
• Depending on disk size, disk synchronization may take from several minutes to several hours.
Synchronization progress can be viewed from the Disk screen. Rebooting or removing power from the Media
Hub during this time is not recommended.
NOTE:
You may use the Media Hub during disk synchronization; however, it will perform at slower speeds.
•
After configuration, available disk space will be the size of Disk 1, and your data will be more protected from damage or loss if a disk fails.
? Revert to single disk mode
To reset the Media Hub to its factory default settings, click this option. All data on your hard disk will be deleted, and all configuration settings will be reset to their factory defaults. For more information, click the ? icon.
Before you click this option, review the following:
•
•
If the Media Hub has two disks, Linksys recommends that you remove one of the disks before continuing.
Existing data on the Media Hub will be lost; Linksys strongly recommends that you back up its data to your computer or an external hard disk before you continue.
• Depending on disk size, configuration may take from several minutes to several hours. Do not manually reboot or power off the Media Hub during this time.
• After configuration, available disk space will be the size of your single hard disk.
Rebuild
This option appears only if two disks are installed and one disk is detected as “new”. To rebuild the Increase
Protection: RAID 1 configuration, click this option.
Before you click this option, review the following:
•
•
Replace the defective disk (refer to Replace a Hard Disk,
Depending on disk size, disk configuration may take from several minutes to several hours. Do not manually reboot or power off the Media Hub during this time.
Rebuild progress can be viewed from the Disk screen.
NOTE:
You may use the Media Hub during configuration; however, it may will perform at slower speeds.
Media Hub
46
Chapter 7
Backup
The Setup Wizard automatically installs backup software on your computer to run backup jobs (unless you choose
not to install it); refer to NTI Shadow, page 37. If you
have installed the backup software, then you can use the backup feature of the Media Hub.
NOTE:
The Backup button only supports
Windows computers installed with the backup software.
Advanced Configuration
Backup
Backup
Click Backup to initiate backup jobs specified by the backup software on your computer(s).
NOTE:
Your computer(s) must be powered on for the jobs to run.
Services
Configure the Remote Access, Windows File Sharing,
Media Server, iTunes Server, and FTP Server settings.
Services
Remote Access
Configure this feature to enable access of the Media
Hub over the Internet. The status of the remote access feature and the Remote Device Name (if configured) are displayed.
NOTE:
Linksys offers Remote Access service
† through www.ciscomediahub.com.
Configure
Click this option to configure this feature.
Media Hub
Remote Access
•
•
Enable Remote Access to the Media Hub
To allow remote access of the Media Hub, select this option. (It is disabled by default.)
If you enable the remote access feature, then configure the Remote Device Name:
Remote Device Name
Enter the Remote Device
Name you want to assign to the Media Hub. It must have between 4 to 50 characters and use only letters, numbers, and dashes. (The Remote Device Name cannot start or end with a dash.)
†
A period of Remote Access is included from date of activation.
Fees may apply thereafter and are subject to change. Go to
www.linksysbycisco.com for further information and details of terms and conditions applicable to the Remote Access service.
47
Chapter 7
If the name is already taken, you will be prompted to enter a different name.
NOTE:
You can change the Remote Device
Name at any time; however, the Media Hub only supports a single Remote Device Name. If you save a new Remote Device Name, then you give up the old one. After you change the Remote
Device Name, the Media Hub will take up to five minutes to implement the new Remote Device
Name. After the Media Hub automatically reboots, the Remote Access service will be available.
Click Submit to save your changes, or click Cancel to cancel your changes.
The Remote Access service will be available in approximately two to five minutes. During this time, the
Media Hub restarts itself, so it will not be available for streaming music or other functions until after the restart.
Remote Access Instructions
1. Open the web browser of the computer you are using.
2. In the Address field, enter this address:
http://www.ciscomediahub.com
Press Enter.
3. Enter the Remote Device Name of the Media Hub, and then click Go.
Enter Remote Device Name
Advanced Configuration
4. To log in as an administrator, enter the Password. Then click Submit.
To log in as a guest, click Guest login and proceed to step 5.
Enter Password
5. Enter the Guest Password (access restricted to the media content of the Media Hub). Then click Submit.
Enter Password
Remote access to the Media Hub is now established.
Video Playback over Remote Access
Follow these guidelines:
•
•
Make sure the computer you are using has the proper plug-ins installed. Playing video files over remote access requires the same plug-ins you have installed on your home computer.
Video playback should be limited to smaller video files, as larger video files may take a long time to load and play.
NOTE:
Video playback support over remote access depends on the broadband speeds of both your home connection and remote connection.
Windows File Sharing
The Media Hub uses the Windows File Sharing feature to share files with other computers, either locally on your network or remotely through the File Browser. The status of this feature is displayed. It is enabled by default and should remain enabled at all times.
The shared folders are listed by name.
Media Hub
48
Chapter 7
Configure
Click this option to configure this feature.
Windows File Sharing
•
•
Enable Windows File Sharing
To disable this feature, deselect Enable Windows File Sharing. Then click
Close to save your change.
Add
To create a shared folder, click Add.
Advanced Configuration
Media Server
The Media Server feature allows the Media Hub to index media files (like a library catalog or database). The status of this feature is displayed. By default, it is enabled.
If you have UPnP AV-enabled (or DLNA-certified) devices in your home, then you can use the Media Hub as a media server. Such devices include digital media adapters and other devices, such as a gaming console with a built-in media player or digital picture frame. For example, if you have a digital media adapter that sends content to your entertainment system, then the digital media adapter can locate the Media Hub using the UPnP AV standard. Media content on the Media Hub can then be accessed and played by the digital media adapter.
Configure
By default, the Media Hub indexes media files stored on itself. To expand the Media Hub’s reach to your local network, click this option.
Add a Shared Folder
•
New share name
Enter a name for the shared folder.
Click Save to save your change, or click Close to cancel your change.
The new shared folder is listed. To change the settings of a shared folder you added, click the pencil icon.
•
Edit share name
Change the name of the shared folder.
Click Save to save your change, or click Close to cancel your change.
To delete a shared folder you added, click the red X icon. When asked to confirm the deletion, click Yes to confirm, or click No to cancel.
NOTE:
The default shared folders (backup, ftp, and media) cannot be changed or deleted.
Click Close to return to the Services screen.
Media Server
•
Find Shared Media on My Local Network
To find shared media files on your local network, select this option. The Media Hub scans its local content and any media content stored in UPnP AV-compatible servers connected to the local network. Indexing of media files on your computers is possible with
Windows Media Player (WMP); however, it is not recommended. Instead, Linksys recommends that you copy media files on your computers to the Media Hub;
refer to Chapter 2: Getting Started, page 5 for more
information.
Click Submit to save your change, or click Cancel to cancel your change.
Media Hub
49
Chapter 7
iTunes Server
To support access by an iTunes library of music files, the
Media Hub offers an iTunes feature. (The Media Hub shares audio files only, not video.) The status of this feature is displayed. By default, it is enabled.
Disable
Click this option to disable this feature.
NOTE:
In iTunes, the Media Hub is displayed in the Shared section. If it is not displayed, enable iTunes to look for shared libraries. Go to Edit >
Preferences > Sharing. Select Look for shared
libraries. Click OK.
FTP Server
To transfer files, the Media Hub can use File Transfer
Protocol (FTP). By default, the FTP Server service is disabled.
Configure
Click this option to configure this feature.
Advanced Configuration
WEB:
For more information about the Media
Hub, refer to the rest of the User Guide. You can also visit www.linksysbycisco.com/support, and select the Media Hub.
FTP
•
•
Enable FTP access
To allow FTP access of the Media
Hub, select this option. (If you do not configure the following Username and Password options, then anonymous FTP access is enabled.)
Require Username and Password for FTP access
To create a login, select this option.
•
Username
Enter a username.
•
Password
Enter a password.
•
Confirm Password
Enter the password again.
Click Submit to save your changes, or click Cancel to cancel your changes.
NOTE:
To use the FTP feature, you must enable port forwarding on your router. Configure the following options:
•
internal port numbers
ports 20 and 21
•
IP address
IP address of the Media Hub
Media Hub
50
Appendix A
Appendix A:
Troubleshooting
You cannot play one of your videos through the Media
Browser of the Media Hub.
The Media Hub plays video content through a browser plug-in. Download and install your favorite media player to enable video playback within the Media Browser.
Please note that media players have varying levels of support for different video formats. If the video format you want to play is not supported, you may want to search the
Internet for a media player that can run on your computer and support the desired video formats. (Make sure you download the latest version.)
Some suggested players include QuickTime, VLC, and
Windows Media Player. For more information about video support, visit http://www.linksysbycisco.com/support.
The power LED of the Media Hub continuously flashes blue or red.
Follow these instructions:
1. To shut down the Media Hub, press and hold the power button until the power LED starts flashing.
If this step does not shut down the Media Hub, then proceed to step 2.
2. Disconnect the power adapter from the Power port of the Media Hub.
3. Disconnect the Ethernet network cable from the
Ethernet port of the Media Hub.
4. Wait five seconds.
5. Re-connect the Ethernet network cable to the Ethernet port of the Media Hub.
6. Re-connect the power adapter to the Power port of the Media Hub.
You cannot access the Media Browser of the Media Hub.
Follow the instructions until you gain access to the Media
Browser:
1. Make sure your computer is connected to the local network. Check the wireless or wired connection.
2. Make sure the Media Hub is connected to the router.
Check the cable connection at both ends.
3. Double-click the desktop icon for the Media Hub (it was created during the Setup Wizard).
Troubleshooting
4. Windows: In the Address field, enter one of the following:
http://<Friendly_Name>(example: http://mediahub) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press Enter.
Mac: In your web browser, enter one of the following:
http://<Friendly_Name>.local (example: http://mediahub.local) or
http://<xxx.xxx.xxx.xxx> (example: http://192.168.1.101)
Press return.
NOTE:
The Friendly Name is the name you created during the Setup Wizard. If you did not create a Friendly Name, use the default; enter http://mediahub (Windows) or
http://mediahub.local (Mac).
You have configured the Media Hub, but you do not see it displayed in Windows Explorer or the Finder.
Change the Workgroup of the Media Hub to match the
Workgroup of your computer. Follow these instructions:
1. Access the browser-based utility of the Media Hub.
(Refer to Chapter 7: Advanced Configuration,
2. On the Media Browser screen, click Configuration.
3. Click Configure System.
4. For the Media Hub Name and Workgroup settings, click
Change, and then follow the on-screen instructions.
NOTE:
If you do not see a drive letter for the
Media Hub, refer to Drive Letter Not Found,
The Media Hub does not recognize your USB storage device.
The USB storage may not have been properly removed from its previous device. Follow these instructions:
1. Disconnect the USB storage device from the Media
Hub.
2. Connect the USB storage device to your computer.
3. Go through the USB safe removal process for your computer.
4. Re-connect the USB storage device to the Media Hub.
Media Hub
51
Appendix A
The iTunes Library does not display the Media Hub.
In iTunes, the Media Hub is displayed in the Shared section.
If the Media Hub is not displayed, enable iTunes to look for shared libraries. Follow these instructions:
1. Go to Edit > Preferences > Sharing.
2. Select Look for shared libraries.
3. Click OK.
NOTE:
The Media Hub shares audio files only, not video, with the iTunes Library.
You cannot access the Media Browser, or the Media Hub does not respond to commands.
Before You Begin
The Media Hub must boot up with at least one hard disk installed. If Disk 1 has been removed and replaced with a new hard disk, then the recovery procedure can be used to re-install the Media Hub.
WARNING:
Before you install the new hard disk, back up its existing data because all data on the new hard disk will be erased.
Instructions for the Recovery Procedure
1. To shut down the Media Hub, press and hold the power button until the power LED starts flashing.
If this step does not shut down the Media Hub, then proceed to step 2.
2. Disconnect the power adapter from the Power port of the Media Hub.
3. While you press and hold down the Reset button, re-connect the power adapter to the Power port of the
Media Hub.
4. Continue to hold down the Reset button for ten seconds. Then release.
5. The Media Hub will undergo its recovery procedure.
WARNING:
Do not reboot or power off the
Media Hub during the recovery procedure.
The recovery procedure will reset the firmware to its factory version, so you may need to do a firmware upgrade when the recovery procedure is complete.
The Media Hub is using Increase Space: Linear 2 mode.
One of the hard disks has failed.
NOTE:
Linksys does not support data recovery after hard disk failure.
Media Hub
Troubleshooting
Before You Begin
Check which hard disk is defective. In the Current RAID
Setting section of the Disk screen, the Slot A setting displays the status of the hard disk in Slot A, which is on the left when you view the front panel of the Media Hub.
The Slot B setting displays the status of the hard disk in
Slot B, which is on the right.
Instructions
1. To shut down the Media Hub, press and hold the power button until the power LED starts flashing.
If this step does not shut down the Media Hub, then proceed to step 2.
2. Disconnect the power adapter from the Power port.
3. To release the drive bay cover, push the button on the top panel.
4. To remove the defective disk, push together the clips of its drive bay, and then pull out the drive bay.
5. Remove the defective disk from its drive bay.
NOTE:
Do not install a replacement hard disk at this time. The Media Hub must revert to single disk mode before you can install a second hard disk.
6. Push down on the hard disk to make sure the connectors are securely seated.
7. Lower the cover, and push it down to secure it.
8. Connect the power adapter to the Power port.
9. Access the browser-based utility of the Media Hub.
(Refer to Chapter 7: Advanced Configuration,
10. On the Media Browser screen, click Configuration.
11. Enter your password, and then click Submit.
12. Click the Disk tab.
13. Click Revert to Single Disk Mode.
Please wait until the Media Hub automatically reboots.
Then the Media Hub will be ready for use.
WARNING:
When a hard disk fails in Increase
Protection: Linear 2 mode, not all data may be recovered.
NOTE:
If you want to install a second hard
disk, then refer to Install a Second Hard Disk,
52
Appendix A
The Media Hub is using Increase Protection: RAID 1 mode. One of the hard disks has failed.
NOTE:
Linksys does not support data recovery after hard disk failure.
Before You Begin
Check which hard disk is defective. In the Current RAID
Setting section of the Disk screen, the Slot A setting displays the status of the hard disk in Slot A, which is on the left when you view the front panel of the Media Hub.
The Slot B setting displays the status of the hard disk in
Slot B, which is on the right.
WARNING:
The replacement hard disk must be blank; otherwise, the Media Hub cannot use it.
NOTE:
Although the Media Hub will work with only one disk, Linksys highly recommends that you replace the defective disk to ensure continued data protection.
Instructions
1. To shut down the Media Hub, press and hold the power button until the power LED starts flashing.
If this step does not shut down the Media Hub, then proceed to step 2.
2. Disconnect the power adapter from the Power port.
3. To release the drive bay cover, push the button on the top panel.
4. To remove the defective disk, push together the clips of its drive bay, and then pull out the drive bay.
5. Remove the hard disk from its drive bay.
6. To install the replacement hard disk, make sure the screw holes of the hard disk line up with the screw holes of the drive bay.
Insert the hard disk into the drive bay.
NOTE:
If you are installing a low-profile or half-height disk, use the four included screws to secure the hard disk in its bay.
7. With the hard disk’s label facing the right side of the
Media Hub, slide the drive bay back into its slot.
8. Push down on the hard disk to make sure the connectors are securely seated.
9. Lower the cover, and push it down to secure it.
10. Connect the power adapter to the Power port.
Media Hub
Troubleshooting
11. Access the browser-based utility of the Media Hub.
(Refer to Chapter 7: Advanced Configuration,
12. On the Media Browser screen, click Configuration.
13. Enter your password, and then click Submit.
14. Click the Disk tab.
15. Click Rebuild.
Please wait until the Media Hub automatically reboots.
Depending on disk size, disk configuration may take from several minutes to several hours. Do not manually reboot or power off the Media Hub during this time.
NOTE:
You may use the Media Hub during configuration; however, it may perform at slower speeds.
You want to install a hard disk that was previously used in a Windows computer.
The Media Hub requires a blank hard disk with no partitions.
Before You Begin
Before you remove the hard disk from the Windows computer, use the Windows Disk Management tool to delete its partitions. (Deleting a partition also deletes its data.)
NOTE:
Your computer must support SATA hard disks; otherwise, this procedure will not work.
Instructions
1. Go to Start > Settings > Control Panel.
2. Double-click Administrative Tools.
3. Double-click Computer Management.
4. In the directory under Storage, click Disk
Management.
5. Right-click the hard disk you want to remove. Then click Delete Partition.
For additional information, refer to Windows Help, and search for this phrase, “Delete Partition”.
53
Appendix A
You initiated an on-demand backup job using the
Media Hub and backup software, but the backup job did not run.
Check the following:
•
•
Your computer must be powered on for the job to run.
Open your backup software. For the options of your backup job, make sure the “On Demand” option is selected. For more information, refer to
NOTE:
The backup options of the Media Hub only support Windows computers installed with the backup software.
You ran a backup job using the Media Hub and backup software, but you cannot find the backup files on the
Media Hub.
• Open your backup software. For the options of your backup job, make sure the Media Hub is the backup destination (the backup folder of the Media Hub is recommended). For more information, refer to
NOTE:
The backup options of the Media Hub only support Windows computers installed with the backup software.
WEB:
If your questions are not addressed here, refer to the Linksys website,
www.linksysbycisco.com
Troubleshooting
Media Hub
54
Appendix B
Appendix B:
Specifications
Model NMH300 - Media Hub
Standards
Ports
Buttons
LEDs
Drive Bays
Certification
Cabling Type
UPnP able/cert
Security Features
Hard Disk Included
Environmental
Dimensions
Weight
Power
Certification
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
IEEE 802.3, IEEE 802.3u,
IEEE 802.3ab
One Power, One Gigabit
Ethernet (10/100/1000),
Two USB 2.0
One Backup, One Reset
One Power
One Power, Two Disk
2 SATA
DLNA 1.5
UTP CAT5E or Better
Discovery, AV
Password for System
Administration, FTP, and
Remote Access
None
198 x 111 x 168 mm
1,41 kg
External 12V/5A
FCC, CE, UL
0 to 35ºC
-25 to 70ºC
10 to 90%, Noncondensing
5 to 95%, Noncondensing
Model NMH305 - Media Hub
Standards
Ports
Buttons
LEDs
Drive Bays
Certification
Cabling Type
UPnP able/cert
IEEE 802.3, IEEE 802.3u,
IEEE 802.3ab
One Power, One Gigabit
Ethernet (10/100/1000),
Two USB 2.0
One Backup, One Reset
One Power
One Power, Two Disk
2 SATA
DLNA 1.5
UTP CAT5E or Better
Discovery, AV
Media Hub
Specifications
Security Features
Hard Disk Included
Environmental
Dimensions
Weight
Power
Certification
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
Password for System
Administration, FTP, and
Remote Access
One 500 GB SATA
198 x 111 x 168 mm
2,04 kg
External 12V/5A
FCC, CE, UL
0 to 35ºC
-25 to 70ºC
10 to 90%, Noncondensing
5 to 95%, Noncondensing
Model NMH405 - Media Hub with LCD
Standards
Ports
IEEE 802.3, IEEE 802.3u,
IEEE 802.3ab
One Power, One Gigabit
Ethernet (10/100/1000),
Two USB 2.0
Memory Cards Supported CompactFlash, Memory
Stick®, Memory Stick Pro®, miniSD™, SD™, xD-PictureCard™ and
MultiMediaCard v3.31
Buttons
LCD
LED
Drive Bays
Certification
Cabling Type
UPnP able/cert
Security Features
Hard Disk Included
Five Navigation,
One Reset, One Power
One 1,8", 176 x 220,
64K Colors
One Power
2 SATA
DLNA 1.5
UTP CAT5E or Better
Discovery, AV
Password for System
Administration, FTP, and
Remote Access
One 500 GB SATA
Environmental
Dimensions
Weight
Power
Certification
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
198 x 111 x 168 mm
2,08 kg
External 12V/5A
FCC, CE, UL
0 to 35ºC
-25 to 70ºC
10 to 90%, Noncondensing
5 to 95%, Noncondensing
55
Appendix B
Model NMH410 - Media Hub with LCD
Standards
Ports
IEEE 802.3, IEEE 802.3u,
IEEE 802.3ab
One Power, One Gigabit
Ethernet (10/100/1000),
Two USB 2.0
Memory Cards Supported CompactFlash, Memory
Stick®, Memory Stick Pro®, miniSD™, SD™, xD-PictureCard™ and
MultiMediaCard v3.31
Buttons
LCD
LED
Drive Bays
Certification
Cabling Type
UPnP able/cert
Security Features
Hard Disk Included
Five Navigation,
One Reset, One Power
One 1,8", 176 x 220,
64K Colors
One Power
2 SATA
DLNA 1.5
UTP CAT5E or Better
Discovery, AV
Password for System
Administration, FTP, and
Remote Access
One 1 TB SATA
Environmental
Dimensions
Weight
Power
Certification
Operating Temp.
Storage Temp.
Operating Humidity
Storage Humidity
198 x 111 x 168 mm
2,11 kg
External 12V/5A
FCC, CE, UL
0 to 35ºC
-25 to 70ºC
10 to 90%, Noncondensing
5 to 95%, Noncondensing
Specifications are subject to change without notice.
Media Hub
Specifications
56
Appendix C
Appendix C:
Warranty Information
Limited Warranty
Linksys warrants that this Linksys hardware product will be substantially free of defects in materials and workmanship arising under normal use during the Warranty Period, which begins on the date of purchase by the original enduser purchaser and lasts for the period specified below:
•
Two (2) years for new product
•
Ninety (90) days for refurbished product
This limited warranty is non-transferable and extends only to the original end-user purchaser. Your exclusive remedy and Linksys’ entire liability under this limited warranty will be for Linksys, at its option, to (a) repair the product with new or refurbished parts, (b) replace the product with a reasonably available equivalent new or refurbished
Linksys product, or (c) refund the purchase price of the product less any rebates. Any repaired or replacement products will be warranted for the remainder of the original Warranty Period or thirty (30) days, whichever is longer. All products and/or parts that are replaced become the property of Linksys.
This limited warranty shall apply in addition to any statutory or other rights which you may have under a contract of sale.
Exclusions and Limitations
This limited warranty does not apply if: (a) the product assembly seal has been removed or damaged, (b) the product has been altered or modified, except by Linksys,
(c) the product damage was caused by use with non-
Linksys products, (d) the product has not been installed, operated, repaired, or maintained in accordance with instructions supplied by Linksys, (e) the product has been subjected to abnormal physical or electrical stress, misuse, negligence, or accident, (f) the serial number on the Product has been altered, defaced, or removed, or (g) the product is supplied or licensed for beta, evaluation, testing or demonstration purposes for which Linksys does not charge a purchase price or license fee.
ALL SOFTWARE PROVIDED BY LINKSYS WITH THE PRODUCT,
WHETHER FACTORY LOADED ON THE PRODUCT OR
CONTAINED ON MEDIA ACCOMPANYING THE PRODUCT,
IS PROVIDED “AS IS” WITHOUT ANY WARRANTY OF ANY
KIND. Without limiting the foregoing, Linksys does not warrant that the operation of the product or software will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Linksys does not warrant that the product, service, software or any equipment, system or
Media Hub
Warranty Information
network on which the product or software is used will be free of vulnerability to intrusion or attack. The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings. This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.
TO THE EXTENT NOT PROHIBITED BY LAW, ALL IMPLIED
WARRANTIES AND CONDITIONS OF MERCHANTABILITY,
SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED
WARRANTY OF NON-INFRINGEMENT, ARE DISCLAIMED.
Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.
TO THE EXTENT NOT PROHIBITED BY LAW, IN NO EVENT
WILL LINKSYS BE LIABLE FOR ANY LOST DATA, REVENUE
OR PROFIT, OR FOR SPECIAL, INDIRECT, CONSEQUENTIAL,
INCIDENTAL OR PUNITIVE DAMAGES, REGARDLESS OF THE
THEORY OF LIABILITY (INCLUDING NEGLIGENCE), ARISING
OUT OF OR RELATED TO THE USE OF OR INABILITY TO
USE THE PRODUCT (INCLUDING ANY SOFTWARE), EVEN
IF LINKSYS HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES. IN NO EVENT WILL LINKSYS’ LIABILITY
EXCEED THE AMOUNT PAID BY YOU FOR THE PRODUCT.
The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.
Obtaining Warranty Service
If you have a question about your product or experience a problem with it, please go to www.linksysbycisco.com/
support where you will find a variety of online support tools and information to assist you with your product. If the product proves defective during the Warranty Period, contact Linksys Technical Support for instructions on how to obtain warranty service. The telephone number for
Linksys Technical Support in your area can be found in the product User Guide and at www.linksysbycisco.com.
Have your product serial number and proof of purchase on hand when calling. A DATED PROOF OF ORIGINAL
PURCHASE IS REQUIRED TO PROCESS WARRANTY CLAIMS.
If you are requested to return your product, you will be given a Return Materials Authorization (RMA) number. You are responsible for properly packaging and shipping your product to Linksys at your cost and risk. You must include
57
Appendix C
the RMA number and a copy of your dated proof of original purchase when returning your product. Products received without a RMA number and dated proof of original purchase will be rejected. Do not include any other items with the product you are returning to Linksys.
Defective product covered by this limited warranty will be repaired or replaced and returned to you without charge.
Customers outside of the United States of America and
Canada are responsible for all shipping and handling charges, custom duties, VAT and other associated taxes and charges. Repairs or replacements not covered under this limited warranty will be subject to charge at Linksys’ then-current rates.
Technical Support
This limited warranty is neither a service nor a support contract. Information about Linksys’ current technical support offerings and policies (including any fees for support services) can be found at
www.linksysbycisco.com/support
General
This limited warranty is governed by the laws of the jurisdiction in which the Product was purchased by you.
If any portion of this limited warranty is found to be void or unenforceable, its remaining provisions shall remain in full force and effect.
Please direct all inquiries to: Linksys, P.O. Box 18558, Irvine,
CA 92623.
For more information, please contact us
www.linksysbycisco.com
Select your country, and then select SUPPORT/
TECHNICAL
For product returns:
Select your Country and then select CUSTOMER SUPPORT
Warranty Information
Media Hub
58
Appendix D
Appendix D:
Regulatory Information
FCC Statement
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1)
This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This product has been tested and complies with the specifications for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used according to the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which is found by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•
•
Reorient or relocate the receiving antenna
Increase the separation between the equipment or devices
• Connect the equipment to an outlet other than the receiver’s
• Consult a dealer or an experienced radio/TV technician for assistance
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
Safety Notices
WARNING:
Do not use this product near water, for example, in a wet basement or near a swimming pool.
WARNING:
Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
Caution: To reduce the risk of fire, use only No.26 AWG or larger telecommunication line cord.
Regulatory Information
Industry Canada Statement
This Class B digital apparatus complies with Canadian
ICES-003.
Operation is subject to the following two conditions:
1. This device may not cause interference and
2. This device must accept any interference, including interference that may cause undesired operation of the device.
Avis d’Industrie Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Le fonctionnement est soumis aux conditions suivantes :
1. Ce périphérique ne doit pas causer d’interférences;
2. Ce périphérique doit accepter toutes les interférences reçues, y compris celles qui risquent d’entraîner un fonctionnement indésirable.
EC Declaration of Conformity (Europe)
In compliance with the EMC Directive 2004/108/EC and
Low Voltage Directive 2006/95/EC as this product meets the requirements of the following standards:
•
•
•
EN55022 Emission
EN55024 Immunity
EN60950-1 Safety
Media Hub
59
Appendix D
User Information for Consumer Products
Covered by EU Directive 2002/96/EC on
Waste Electric and Electronic Equipment
(WEEE)
This document contains important information for users with regards to the proper disposal and recycling of
Linksys products. Consumers are required to comply with this notice for all electronic products bearing the following symbol:
English - Environmental Information for Customers in the European Union
European Directive 2002/96/EC requires that the equipment bearing this symbol on the product and/or its packaging must not be disposed of with unsorted municipal waste. The symbol indicates that this product should be disposed of separately from regular household waste streams. It is your responsibility to dispose of this and other electric and electronic equipment via designated collection facilities appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. For more detailed information about the disposal of your old equipment, please contact your local authorities, waste disposal service, or the shop where you purchased the product.
Български (Bulgarian) - Информация относно опазването на околната среда за потребители в
Европейския съюз
Европейска директива 2002/96/EC изисква уредите, носещи този символ върху изделието и/или опаковката му, да не се изхвърля т с несортирани битови отпадъци. Символът обозначава, че изделието трябва да се изхвърля отделно от сметосъбирането на обикновените битови отпадъци. Ваша е отговорността този и другите електрически и електронни уреди да се изхвърлят в предварително определени от държавните или общински органи специализирани пунктове за събиране. Правилното изхвърляне и рециклиране ще спомогнат да се предотвратят евентуални вредни за околната среда и здравето на населението последствия. За по-подробна информация относно изхвърлянето на вашите стари уреди се обърнете към местните власти, службите за сметосъбиране или магазина, от който сте закупили уреда.
Regulatory Information
Čeština (Czech) - Informace o ochraně životního prostředí pro zákazníky v zemích Evropské unie
Evropská směrnice 2002/96/ES zakazuje, aby zařízení označené tímto symbolem na produktu anebo na obalu bylo likvidováno s netříděným komunálním odpadem. Tento symbol udává, že daný produkt musí být likvidován odděleně od běžného komunálního odpadu. Odpovídáte za likvidaci tohoto produktu a dalších elektrických a elektronických zařízení prostřednictvím určených sběrných míst stanovených vládou nebo místními
úřady. Správná likvidace a recyklace pomáhá předcházet potenciálním negativním dopadům na životní prostředí a lidské zdraví. Podrobnější informace o likvidaci starého vybavení si laskavě vyžádejte od místních úřadů, podniku zabývajícího se likvidací komunálních odpadů nebo obchodu, kde jste produkt zakoupili.
Dansk (Danish) - Miljøinformation for kunder i EU
EU-direktiv 2002/96/EF kræver, at udstyr der bærer dette symbol
på produktet og/eller emballagen ikke må bortskaffes som usorteret kommunalt affald. Symbolet betyder, at dette produkt skal bortskaffes adskilt fra det almindelige husholdningsaffald.
Det er dit ansvar at bortskaffe dette og andet elektrisk og elektronisk udstyr via bestemte indsamlingssteder udpeget af staten eller de lokale myndigheder. Korrekt bortskaffelse og genvinding vil hjælpe med til at undgå mulige skader for miljøet og menneskers sundhed. Kontakt venligst de lokale myndigheder, renovationstjenesten eller den butik, hvor du har købt produktet, angående mere detaljeret information om bortskaffelse af dit gamle udstyr.
Deutsch (German) - Umweltinformation für Kunden innerhalb der Europäischen Union
Die Europäische Richtlinie 2002/96/EC verlangt, dass technische
Ausrüstung, die direkt am Gerät und/oder an der Verpackung mit diesem Symbol versehen ist , nicht zusammen mit unsortiertem
Gemeindeabfall entsorgt werden darf. Das Symbol weist darauf hin, dass das Produkt von regulärem Haushaltmüll getrennt entsorgt werden sollte. Es liegt in Ihrer Verantwortung, dieses
Gerät und andere elektrische und elektronische Geräte über die dafür zuständigen und von der Regierung oder örtlichen
Behörden dazu bestimmten Sammelstellen zu entsorgen.
Ordnungsgemäßes Entsorgen und Recyceln trägt dazu bei, potentielle negative Folgen für Umwelt und die menschliche
Gesundheit zu vermeiden. Wenn Sie weitere Informationen zur
Entsorgung Ihrer Altgeräte benötigen, wenden Sie sich bitte an die örtlichen Behörden oder städtischen Entsorgungsdienste oder an den Händler, bei dem Sie das Produkt erworben haben.
Media Hub
60
Appendix D
Eesti (Estonian) - Keskkonnaalane informatsioon
Euroopa Liidus asuvatele klientidele
Euroopa Liidu direktiivi 2002/96/EÜ nõuete kohaselt on seadmeid, millel on tootel või pakendil käesolev sümbol , keelatud kõrvaldada koos sorteerimata olmejäätmetega. See sümbol näitab, et toode tuleks kõrvaldada eraldi tavalistest olmejäätmevoogudest. Olete kohustatud kõrvaldama käesoleva ja ka muud elektri- ja elektroonikaseadmed riigi või kohalike ametiasutuste poolt ette nähtud kogumispunktide kaudu.
Seadmete korrektne kõrvaldamine ja ringlussevõtt aitab vältida võimalikke negatiivseid tagajärgi keskkonnale ning inimeste tervisele. Vanade seadmete kõrvaldamise kohta täpsema informatsiooni saamiseks võtke palun ühendust kohalike ametiasutustega, jäätmekäitlusfirmaga või kauplusega, kust te toote ostsite.
Español (Spanish) - Información medioambiental para clientes de la Unión Europea
La Directiva 2002/96/CE de la UE exige que los equipos que lleven este símbolo en el propio aparato y/o en su embalaje no deben eliminarse junto con otros residuos urbanos no seleccionados. El símbolo indica que el producto en cuestión debe separarse de los residuos domésticos convencionales con vistas a su eliminación. Es responsabilidad suya desechar este y cualesquiera otros aparatos eléctricos y electrónicos a través de los puntos de recogida que ponen a su disposición el gobierno y las autoridades locales. Al desechar y reciclar correctamente estos aparatos estará contribuyendo a evitar posibles consecuencias negativas para el medio ambiente y la salud de las personas. Si desea obtener información más detallada sobre la eliminación segura de su aparato usado, consulte a las autoridades locales, al servicio de recogida y eliminación de residuos de su zona o pregunte en la tienda donde adquirió el producto.
Ελληνικά (Greek) - Στοιχεία περιβαλλοντικής
προστασίας για πελάτες εντός της Ευρωπαϊκής
Ένωσης
Σύμφωνα με την Κοινοτική Οδηγία 2002/96/EC, ο εξοπλισμός που
φέρει αυτό το σύμβολο στο προϊόν ή/και τη συσκευασία του
δεν πρέπει να απορρίπτεται μαζί με τα μη διαχωρισμένα αστικά
απορρίμματα. Το σύμβολο υποδεικνύει ότι αυτό το προϊόν θα
πρέπει να απορρίπτεται ξεχωριστά από τα συνήθη οικιακά
απορρίμματα. Είστε υπεύθυνος για την απόρριψη του παρόντος
και άλλου ηλεκτρικού και ηλεκτρονικού εξοπλισμού μέσω των
καθορισμένων εγκαταστάσεων συγκέντρωσης απορριμμάτων,
οι οποίες ορίζονται από το κράτος ή τις αρμόδιες τοπικές αρχές.
Η σωστή απόρριψη και ανακύκλωση συμβάλλει στην πρόληψη
ενδεχόμενων αρνητικών επιπτώσεων στο περιβάλλον και την
υγεία. Για περισσότερες πληροφορίες σχετικά με την απόρριψη
του παλαιού σας εξοπλισμού, επικοινωνήστε με τις τοπικές αρχές,
τις υπηρεσίες αποκομιδής απορριμμάτων ή το κατάστημα από
το οποίο αγοράσατε το προϊόν.
Regulatory Information
Français (French) - Informations environnementales pour les clients de l’Union européenne
La directive européenne 2002/96/CE exige que l’équipement sur lequel est apposé ce symbole sur le produit et/ou son emballage ne soit pas jeté avec les autres ordures ménagères. Ce symbole indique que le produit doit être éliminé dans un circuit distinct de celui pour les déchets des ménages. Il est de votre responsabilité de jeter ce matériel ainsi que tout autre matériel
électrique ou électronique par les moyens de collecte indiqués par le gouvernement et les pouvoirs publics des collectivités territoriales. L’élimination et le recyclage en bonne et due forme ont pour but de lutter contre l’impact néfaste potentiel de ce type de produits sur l’environnement et la santé publique. Pour plus d’informations sur le mode d’élimination de votre ancien
équipement, veuillez prendre contact avec les pouvoirs publics locaux, le service de traitement des déchets, ou l’endroit où vous avez acheté le produit.
Italiano (Italian) - Informazioni relative all’ambiente per i clienti residenti nell’Unione Europea
La direttiva europea 2002/96/EC richiede che le apparecchiature contrassegnate con questo simbolo sul prodotto e/o sull’imballaggio non siano smaltite insieme ai rifiuti urbani non differenziati. Il simbolo indica che questo prodotto non deve essere smaltito insieme ai normali rifiuti domestici. È responsabilità del proprietario smaltire sia questi prodotti sia le altre apparecchiature elettriche ed elettroniche mediante le specifiche strutture di raccolta indicate dal governo o dagli enti pubblici locali. Il corretto smaltimento ed il riciclaggio aiuteranno a prevenire conseguenze potenzialmente negative per l’ambiente e per la salute dell’essere umano. Per ricevere informazioni più dettagliate circa lo smaltimento delle vecchie apparecchiature in Vostro possesso, Vi invitiamo a contattare gli enti pubblici di competenza, il servizio di smaltimento rifiuti o il negozio nel quale avete acquistato il prodotto.
Latviešu valoda (Latvian) - Ekoloģiska informācija klientiem Eiropas Savienības jurisdikcijā
Direktīvā 2002/96/EK ir prasība, ka aprīkojumu, kam pievienota zīme uz paša izstrādājuma vai uz tā iesaiņojuma, nedrīkst izmest nešķirotā veidā kopā ar komunālajiem atkritumiem
(tiem, ko rada vietēji iedzīvotāji un uzņēmumi). Šī zīme nozīmē to, ka šī ierīce ir jāizmet atkritumos tā, lai tā nenonāktu kopā ar parastiem mājsaimniecības atkritumiem. Jūsu pienākums ir šo un citas elektriskas un elektroniskas ierīces izmest atkritumos, izmantojot īpašus atkritumu savākšanas veidus un līdzekļus, ko nodrošina valsts un pašvaldību iestādes. Ja izmešana atkritumos un pārstrāde tiek veikta pareizi, tad mazinās iespējamais kaitējums dabai un cilvēku veselībai. Sīkākas ziņas par novecojuša aprīkojuma izmešanu atkritumos jūs varat saņemt vietējā pašvaldībā, atkritumu savākšanas dienestā, kā arī veikalā, kur iegādājāties šo izstrādājumu.
Media Hub
61
Appendix D
Lietuvškai (Lithuanian) - Aplinkosaugos informacija, skirta Europos Sąjungos vartotojams
Europos direktyva 2002/96/EC numato, kad įrangos, kuri ir kurios pakuotė yra pažymėta šiuo simboliu (įveskite simbolį), negalima šalinti kartu su nerūšiuotomis komunalinėmis atliekomis. Šis simbolis rodo, kad gaminį reikia šalinti atskirai nuo bendro buitinių atliekų srauto. Jūs privalote užtikrinti, kad
ši ir kita elektros ar elektroninė įranga būtų šalinama per tam tikras nacionalinės ar vietinės valdžios nustatytas atliekų rinkimo sistemas. Tinkamai šalinant ir perdirbant atliekas, bus išvengta galimos žalos aplinkai ir žmonių sveikatai. Daugiau informacijos apie jūsų senos įrangos šalinimą gali pateikti vietinės valdžios institucijos, atliekų šalinimo tarnybos arba parduotuvės, kuriose įsigijote tą gaminį.
Malti (Maltese) - Informazzjoni Ambjentali għal Klijenti fl-Unjoni Ewropea
Id-Direttiva Ewropea 2002/96/KE titlob li t-tagħmir li jkun fih issimbolu fuq il-prodott u/jew fuq l-ippakkjar ma jistax jintrema ma’ skart muniċipali li ma ġiex isseparat. Is-simbolu jindika li dan il-prodott għandu jintrema separatament minn ma’ liskart domestiku regolari. Hija responsabbiltà tiegħek li tarmi dan it-tagħmir u kull tagħmir ieħor ta’ l-elettriku u elettroniku permezz ta’ faċilitajiet ta’ ġbir appuntati apposta mill-gvern jew mill-awtoritajiet lokali. Ir-rimi b’mod korrett u r-riċiklaġġ jgħin jipprevjeni konsegwenzi negattivi potenzjali għall-ambjent u għas-saħħa tal-bniedem. Għal aktar informazzjoni dettaljata dwar ir-rimi tat-tagħmir antik tiegħek, jekk jogħġbok ikkuntattja lill-awtoritajiet lokali tiegħek, is-servizzi għar-rimi ta’ l-iskart, jew il-ħanut minn fejn xtrajt il-prodott.
Magyar (Hungarian) - Környezetvédelmi információ az európai uniós vásárlók számára
A 2002/96/EC számú európai uniós irányelv megkívánja, hogy azokat a termékeket, amelyeken, és/vagy amelyek csomagolásán az alábbi címke megjelenik, tilos a többi szelektálatlan lakossági hulladékkal együtt kidobni. A címke azt jelöli, hogy az adott termék kidobásakor a szokványos háztartási hulladékelszállítási rendszerektõl elkülönített eljárást kell alkalmazni. Az Ön felelõssége, hogy ezt, és más elektromos és elektronikus berendezéseit a kormányzati vagy a helyi hatóságok által kijelölt gyűjtõredszereken keresztül számolja fel. A megfelelõ hulladékfeldolgozás segít a környezetre és az emberi egészségre potenciálisan ártalmas negatív hatások megelõzésében. Ha elavult berendezéseinek felszámolásához további részletes információra van szüksége, kérjük, lépjen kapcsolatba a helyi hatóságokkal, a hulladékfeldolgozási szolgálattal, vagy azzal
üzlettel, ahol a terméket vásárolta.
Regulatory Information
Nederlands (Dutch) - Milieu-informatie voor klanten in de Europese Unie
De Europese Richtlijn 2002/96/EC schrijft voor dat apparatuur die is voorzien van dit symbool op het product of de verpakking, niet mag worden ingezameld met niet-gescheiden huishoudelijk afval. Dit symbool geeft aan dat het product apart moet worden ingezameld. U bent zelf verantwoordelijk voor de vernietiging van deze en andere elektrische en elektronische apparatuur via de daarvoor door de landelijke of plaatselijke overheid aangewezen inzamelingskanalen. De juiste vernietiging en recycling van deze apparatuur voorkomt mogelijke negatieve gevolgen voor het milieu en de gezondheid. Voor meer informatie over het vernietigen van uw oude apparatuur neemt u contact op met de plaatselijke autoriteiten of afvalverwerkingsdienst, of met de winkel waar u het product hebt aangeschaft.
Norsk (Norwegian) - Miljøinformasjon for kunder i EU
EU-direktiv 2002/96/EF krever at utstyr med følgende symbol
avbildet på produktet og/eller pakningen, ikke må kastes sammen med usortert avfall. Symbolet indikerer at dette produktet skal håndteres atskilt fra ordinær avfallsinnsamling for husholdningsavfall. Det er ditt ansvar å kvitte deg med dette produktet og annet elektrisk og elektronisk avfall via egne innsamlingsordninger slik myndighetene eller kommunene bestemmer. Korrekt avfallshåndtering og gjenvinning vil være med på å forhindre mulige negative konsekvenser for miljø og helse. For nærmere informasjon om håndtering av det kasserte utstyret ditt, kan du ta kontakt med kommunen, en innsamlingsstasjon for avfall eller butikken der du kjøpte produktet.
Polski (Polish) - Informacja dla klientów w Unii
Europejskiej o przepisach dotyczących ochrony środowiska
Dyrektywa Europejska 2002/96/EC wymaga, aby sprzęt oznaczony symbolem znajdującym się na produkcie i/lub jego opakowaniu nie był wyrzucany razem z innymi niesortowanymi odpadami komunalnymi. Symbol ten wskazuje, że produkt nie powinien być usuwany razem ze zwykłymi odpadami z gospodarstw domowych. Na Państwu spoczywa obowiązek wyrzucania tego i innych urządzeń elektrycznych oraz elektronicznych w punktach odbioru wyznaczonych przez władze krajowe lub lokalne. Pozbywanie się sprzętu we właściwy sposób i jego recykling pomogą zapobiec potencjalnie negatywnym konsekwencjom dla środowiska i zdrowia ludzkiego. W celu uzyskania szczegółowych informacji o usuwaniu starego sprzętu, prosimy zwrócić się do lokalnych władz, służb oczyszczania miasta lub sklepu, w którym produkt został nabyty.
Media Hub
62
Appendix D
Português (Portuguese) - Informação ambiental para clientes da União Europeia
A Directiva Europeia 2002/96/CE exige que o equipamento que exibe este símbolo no produto e/ou na sua embalagem não seja eliminado junto com os resíduos municipais não separados. O símbolo indica que este produto deve ser eliminado separadamente dos resíduos domésticos regulares.
É da sua responsabilidade eliminar este e qualquer outro equipamento eléctrico e electrónico através das instalações de recolha designadas pelas autoridades governamentais ou locais. A eliminação e reciclagem correctas ajudarão a prevenir as consequências negativas para o ambiente e para a saúde humana. Para obter informações mais detalhadas sobre a forma de eliminar o seu equipamento antigo, contacte as autoridades locais, os serviços de eliminação de resíduos ou o estabelecimento comercial onde adquiriu o produto.
Română (Romanian) - Informaţii de mediu pentru clienţii din Uniunea Europeană
Directiva europeană 2002/96/CE impune ca echipamentele care prezintă acest simbol pe produs şi/sau pe ambalajul acestuia să nu fie casate împreună cu gunoiul menajer municipal. Simbolul indică faptul că acest produs trebuie să fie casat separat de gunoiul menajer obişnuit. Este responsabilitatea dvs. să casaţi acest produs şi alte echipamente electrice şi electronice prin intermediul unităţilor de colectare special desemnate de guvern sau de autorităţile locale. Casarea şi reciclarea corecte vor ajuta la prevenirea potenţialelor consecinţe negative asupra sănătăţii mediului şi a oamenilor. Pentru mai multe informaţii detaliate cu privire la casarea acestui echipament vechi, contactaţi autorităţile locale, serviciul de salubrizare sau magazinul de la care aţi achiziţionat produsul.
Slovenčina (Slovak) - Informácie o ochrane životného prostredia pre zákazníkov v Európskej únii
Podľa európskej smernice 2002/96/ES zariadenie s týmto symbolom na produkte a/alebo jeho balení nesmie byť likvidované spolu s netriedeným komunálnym odpadom.
Symbol znamená, že produkt by sa mal likvidovať oddelene od bežného odpadu z domácností. Je vašou povinnosťou likvidovať toto i ostatné elektrické a elektronické zariadenia prostredníctvom špecializovaných zberných zariadení určených vládou alebo miestnymi orgánmi. Správna likvidácia a recyklácia pomôže zabrániť prípadným negatívnym dopadom na životné prostredie a zdravie ľudí. Ak máte záujem o podrobnejšie informácie o likvidácii starého zariadenia, obráťte sa, prosím, na miestne orgány, organizácie zaoberajúce sa likvidáciou odpadov alebo obchod, v ktorom ste si produkt zakúpili.
Regulatory Information
Slovenščina (Slovene) - Okoljske informacije za stranke v Evropski uniji
Evropska direktiva 2002/96/ES prepoveduje odlaganje opreme s tem simbolom – na izdelku in/ali na embalaži z nesortiranimi komunalnimi odpadki. Ta simbol opozarja, da je treba izdelek zavreči ločeno od preostalih gospodinjskih odpadkov. Vaša odgovornost je, da to in preostalo električno in elektronsko opremo oddate na posebna zbirališča, ki jih določijo državne ustanove ali lokalne oblasti. S pravilnim odlaganjem in recikliranjem boste preprečili morebitne škodljive vplive na okolje in zdravje ljudi. Če želite izvedeti več o odlaganju stare opreme, se obrnite na lokalne oblasti, odlagališče odpadkov ali trgovino, kjer ste izdelek kupili.
Suomi (Finnish) - Ympäristöä koskevia tietoja EUalueen asiakkaille
EU-direktiivi 2002/96/EY edellyttää, että jos laitteistossa on tämä symboli itse tuotteessa ja/tai sen pakkauksessa, laitteistoa ei saa hävittää lajittelemattoman yhdyskuntajätteen mukana.
Symboli merkitsee sitä, että tämä tuote on hävitettävä erillään tavallisesta kotitalousjätteestä. Sinun vastuullasi on hävittää tämä elektroniikkatuote ja muut vastaavat elektroniikkatuotteet viemällä tuote tai tuotteet viranomaisten määräämään keräyspisteeseen. Laitteiston oikea hävittäminen estää mahdolliset kielteiset vaikutukset ympäristöön ja ihmisten terveyteen. Lisätietoja vanhan laitteiston oikeasta hävitystavasta saa paikallisilta viranomaisilta, jätteenhävityspalvelusta tai siitä myymälästä, josta ostit tuotteen.
Svenska (Swedish) - Miljöinformation för kunder i
Europeiska unionen
Det europeiska direktivet 2002/96/EC kräver att utrustning med denna symbol på produkten och/eller förpackningen inte får kastas med osorterat kommunalt avfall. Symbolen visar att denna produkt bör kastas efter att den avskiljts från vanligt hushållsavfall.
Det faller på ditt ansvar att kasta denna och annan elektrisk och elektronisk utrustning på fastställda insamlingsplatser utsedda av regeringen eller lokala myndigheter. Korrekt kassering och
återvinning skyddar mot eventuella negativa konsekvenser för miljön och personhälsa. För mer detaljerad information om kassering av din gamla utrustning kontaktar du dina lokala myndigheter, avfallshanteringen eller butiken där du köpte produkten.
WEB:
For additional information, please visit
www.linksysbycisco.com/international
Media Hub
63
Appendix E
Appendix E: Software End
User License Agreement
Cisco Products
This product from Cisco Systems, Inc. or its subsidiary licensing the Software instead of Cisco Systems, Inc.
(“Cisco”) contains software (including firmware) originating from Cisco and its suppliers and may also contain software from the open source community.
Any software originating from Cisco and its suppliers is licensed under the Cisco Software License Agreement contained at Schedule 1 below. You may also be prompted to review and accept the Cisco Software License Agreement upon installation of the software. Separate terms and features of Network Magic, a Cisco Software product, are set forth in Schedule 2 below.
Any software from the open source community is licensed under the specific license terms applicable to that software made available by Cisco at www.linksysbycisco.com/gpl or as provided for in Schedule 3 below. By using the Software, you acknowledge that you have reviewed such license terms and that you agree to be bound by the terms of such licenses. Where such specific license terms entitle you to the source code of such software, that source code is available upon request at cost from Cisco for at least three years from the purchase date of this product and may also be available for download from
www.linksysbycisco.com/gpl. For detailed license terms and additional information on open source software in
Cisco products please look at the Cisco public web site at:
www.linksysbycisco.com/gpl/ or Schedule 3 below as applicable. If you would like a copy of the GPL or certain other open source code in this Software on a CD, Cisco will mail to you a CD with such code for $9.99 plus the cost of shipping, upon request.
THIS SOFTWARE END USER LICENSE AGREEMENT IS
A LEGAL AGREEMENT BETWEEN YOU AND CISCO.
READ IT CAREFULLY BEFORE INSTALLING AND USING
THE SOFTWARE. IT PROVIDES A LICENSE TO USE THE
SOFTWARE AND CONTAINS WARRANTY INFORMATION
AND LIABILITY DISCLAIMERS. BY CHECKING THE “NEXT”
BOX, DOWNLOADING, INSTALLING OR USING THE
SOFTWARE, OR USING THE PRODUCT CONTAINING THE
SOFTWARE, YOU ARE CONFIRMING YOUR ACCEPTANCE
OF THE SOFTWARE AND CONSENTING TO BE BOUND
BY THIS AGREEMENT. IF YOU DO NOT AGREE TO ALL
OF THESE TERMS, THEN DO NOT CLICK ON THE “NEXT”
BUTTON AND DO NOT DOWNLOAD, INSTALL OR USE THE
SOFTWARE. YOU MAY RETURN UNUSED SOFTWARE (OR,
IF THE SOFTWARE IS SUPPLIED AS PART OF ANOTHER
PRODUCT, THE UNUSED PRODUCT) FOR A FULL REFUND
UP TO 30 DAYS AFTER ORIGINAL PURCHASE, SUBJECT TO
Media Hub
Software End User License Agreement
THE RETURN PROCESS AND POLICIES OF THE PARTY FROM
WHICH YOU PURCHASED SUCH PRODUCT OR SOFTWARE.
IN THE EVENT THAT YOU HAVE ELECTED TO OBTAIN A
SUBSCRIPTION LICENSE, AS INDICATED IN YOUR ORDER,
YOU ADDITIONALLY AGREE TO BE BOUND BY THE “TERMS
OF SERVICE” SET FORTH IN SCHEDULE 2 IF APPLICABLE.
Software Licenses
The software licenses applicable to software from Cisco are made available at the Cisco public web site at:
www.linksysbycisco.com and
www.linksysbycisco.com/gpl/ respectively. For your convenience of reference, a copy of the Cisco Software
License Agreement and the main open source code licenses used by Cisco in its products are contained in the
Schedules below.
Schedule 1
Cisco Software License Agreement
License. Subject to the terms and conditions of this
Agreement, Cisco grants the original end user purchaser of the Software a nonexclusive license to (i) use the Software solely as embedded in, as a stand-alone application or
(where authorized in the applicable documentation) for communication with such product, each solely at Cisco’s discretion; (ii) if the Software is purchased separately from any Cisco Product, install the Software on personal computers within a single household or business location according to the maximum number of licenses you have purchased; and (iii) make one copy of the
Software in machine-readable form and one copy of the
Documentation, solely for backup purposes. This license may not be sublicensed, and is not transferable except to a person or entity to which you transfer ownership of the complete Cisco product containing the Software or complete Software product, provided you permanently transfer all rights under this Agreement and do not retain any full or partial copies of the Software, and the recipient agrees to the terms of this Agreement.
“Software” includes, and this Agreement will apply to (a) the software of Cisco or its suppliers purchased separately or provided in or with the applicable Cisco product, and
(b) any upgrades, updates, bug fixes or modified versions
(“Upgrades”) or backup copies of the Software supplied to you by Cisco or an authorized reseller (whether or not for a fee), provided you already hold a valid license to the original software and have paid any applicable fee for the
Upgrade.
“Documentation” means all documentation and other related materials supplied by Cisco to you pursuant to this
Agreement.
64
Appendix E
License Restrictions. Other than as set forth in this
Agreement, you may not (i) make or distribute copies of the Software or its related Documentation, or electronically transfer the Software or Documentation from one computer to another or over a network; (ii) alter, merge, modify, adapt, decrypt or translate the Software or related Documentation, or decompile, reverse engineer, disassemble, or otherwise reduce the Software to a human-perceivable form (except to the extent expressly permitted by law notwithstanding this provision); (iii) share, sell, rent, lease, or sublicense the Software or related Documentation; (iv) modify the Software or create derivative works based upon the Software; (v) if you make a backup copy of the Software and Documentation, you must reproduce all copyright notices and any other proprietary legends found on the original Software and
Documentation; (vi) use the Software for management of a business network with more than 8 computers; (vii) use the Software under any circumstances for competitive evaluation, including developing competing software;
(ix) to the extent permitted under applicable law, assign, sublicense or otherwise transfer the Software unless the prospective assignee, sublicensee or transferee expressly agrees to all the terms and conditions under this
Agreement.
The Software and Documentation contain trade secrets and/or copyrighted materials of Cisco or its suppliers. You will not disclose or make available such trade secrets or copyrighted material in any form to any third party.
In the event that you fail to comply with this Agreement, the license granted to you will automatically terminate, at which time you must immediately (i) stop using the
Cisco Product in which the Software is embedded, or
(ii) uninstall the Software and destroy all copies of the
Software and Documentation where the Software is purchased separately. All other rights of both parties and all other provisions of this Agreement will survive this termination.
Ownership. The Software and Documentation are licensed and not sold to you by Cisco and the relevant third parties set forth in Schedule 3. Cisco and its licensors retain all right, title and interest, including all copyright and intellectual property rights, in and to, the Software and Documentation and all copies and portions thereof.
All rights not specifically granted to you in this Agreement are reserved by Cisco and its licensors. Your use of any software product from an entity other than Cisco that may have been recommended by Cisco is governed by such software product’s end user license agreement.
Third Party Services, Links and Advertising. Cisco may provide from within the Software links to websites or third party software products. In addition, third party services may be provided with the Software which may be subject to terms and conditions from the provider of the service. Cisco makes no representations as to the quality,
Media Hub
Software End User License Agreement
suitability, functionality, or legality of any sites or products to which links may be provided or third party services, and you hereby waive any claim you might have against Cisco with respect to such sites or third party software products or services. Your correspondence or business dealings with, or participation in promotions of third parties found through the Software and any other terms, conditions, warranties, or representations associated with such dealings, are solely between you and such third party. You agree that Cisco is not responsible or liable for any loss or damage of any sort incurred as the result of any such dealings or as the result of the presence of such third party links, products or services in the Cisco Software, and Cisco may discontinue or modify the services or links offered at any time.
Collection and Processing of Information. You agree that Cisco and/or its affiliates may, from time to time, collect and process information about your Cisco product and/or the Software and/or your use of either in order
(i) to enable Cisco to offer you Upgrades; (ii) to provide support and assistance with your product and/or the
Software; (iii) to ensure that your Cisco product and/or the Software is being used in accordance with the terms of this Agreement; (iv) to provide improvements to the way Cisco delivers technology to you and to other Cisco customers; (v) to provide reports regarding the status and health of the network, including network traffic and application usage; (vi) to enable Cisco to comply with the terms of any agreements it has with any third parties regarding your Cisco product and/or Software; and/or
(vii) to enable Cisco to comply with all applicable laws and/or regulations, or the requirements of any regulatory authority or government agency. Cisco and/ or its affiliates may collect and process this information provided that it does not identify you personally. You agree that Cisco has no responsibility or liability for the deletion of or failure to store any data or other information related to your Cisco product, Software or related Services.
The reports feature of certain Software allows you to monitor the activity of computers running the Software in your home or small office. You must activate this feature in order to receive reports. If you activate the reports feature, you agree to the following: (a) the Software tracks and monitors the following components and activities in your home or office: network traffic (e.g. megabytes per hour), application usage (the foreground window is tracked and the time each application is in the foreground during active usage of the computer) and internet history. (b)
For all computers on which reports feature is enabled, the above information is transmitted to servers at Cisco and/ or a third party at periodic intervals while the computer is online. This information is associated and stored with the email address supplied by you when you activated the reports feature. This information is summarized into a formal report and is emailed to the identified email address. © Any computer on the network running the
65
Appendix E
Software can enable any other computer (on the same primary network) to generate reports. When a computer is enabled, that computer shows a notification that it is being monitored. As long as that computer is enabled, each time the Software is started the user of that particular computer will see a notification that it is being monitored by the reports feature. Any computer on the network with the Software installed can enable or disable any other computer from the reports feature.
In addition, Cisco may collect and store detailed information regarding your network configuration and usage for the purpose of providing you technical networking support. The information is associated with you only when you provide a unique ID number to the support representative while you are receiving help. The unique ID is generated randomly on your computer upon installation and is completely under your control.
Your use of your Cisco product and/or the Software constitutes consent by you to Cisco’s and/or its affiliates’ collection and use of such information and, for European
Economic Area (EEA) customers, to the transfer of such information to a location outside the EEA. Any information collected by your Cisco product and/or the Software is done and utilized in accordance with our Privacy Policy available at Privacy Statement. Your election to use the
Cisco product and/or Software indicates your acceptance of the terms of the Cisco Privacy Policy, so please review the policy carefully and check the Web site above to review updates to it.
Software Upgrades etc. If the Software enables you to receive Upgrades, you may elect at any time to receive these Upgrades either automatically or manually. If you elect to receive Upgrades manually or you otherwise elect not to receive or be notified of any Upgrades, you may expose your Cisco product and/or the Software to serious security threats and/or some features within your
Cisco product and/or Software may become inaccessible.
There may be circumstances where we apply an Upgrade automatically in order to comply with changes in legislation, legal, security or regulatory requirements or as a result of requirements to comply with the terms of any agreements Cisco has with any third parties regarding your Cisco product and/or the Software. You will always be notified of any Upgrades being delivered to you. The terms of this license will apply to any such Upgrade unless the Upgrade in question is accompanied by a separate license, in which event the terms of that license will apply.
Changes to Browser Settings and Error Processing. By installing the Software, you acknowledge and agree that the Software may change certain settings in your Internet browser software, including the default settings for search provider and source of DNS error pages and may direct erroneous URLs to an error landing page hosted by Cisco.
You may opt out of these settings by not accepting them as
Media Hub
Software End User License Agreement
part of the installation process or by requesting a change to your software settings in the error process. Installing the software and changing these software settings may conflict with license agreements you have entered into with other entities, such as your Internet service provider.
Error queries that are libelous, slanderous, defamatory or that may violate the intellectual property rights of others may not be processed by Cisco or its suppliers.
Term and Termination. You may terminate this License at any time by destroying all copies of the Software and documentation. Your rights under this License will terminate immediately without notice from Cisco if you fail to comply with any provision of this Agreement.
Limited Warranty. Cisco additionally warrants that any media on which the Software may be provided will be free from defects in materials and workmanship under normal use for a period of ninety (90) days from the date of original purchase. Your exclusive remedy and Cisco’s entire liability under this limited warranty will be for Cisco, at its option, to (a) replace the Software media, or (b) refund the purchase price of the Software media.
EXCEPT FOR THE LIMITED WARRANTY ON MEDIA
SET FORTH ABOVE AND TO THE MAXIMUM EXTENT
PERMITTED BY APPLICABLE LAW, ALL SOFTWARE AND
SERVICES PROVIDED BY CISCO ARE PROVIDED “AS IS” WITH
ALL FAULTS AND WITHOUT WARRANTY OF ANY KIND.
Without limiting the foregoing, Cisco does not warrant that the operation of the product, software or services will be uninterrupted or error free. Also, due to the continual development of new techniques for intruding upon and attacking networks, Cisco does not warrant that the product, software or services, or any equipment, system or network on which the product, software or services are used will be free of vulnerability to intrusion or attack.
The product may include or be bundled with third party software or service offerings. This limited warranty shall not apply to such third party software or service offerings.
This limited warranty does not guarantee any continued availability of a third party’s service for which this product’s use or operation may require.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE
LAW, ALL IMPLIED WARRANTIES AND CONDITIONS
OF MERCHANTABILITY, SATISFACTORY QUALITY,
NONINFRINGEMENT OR FITNESS FOR A PARTICULAR
PURPOSE ARE LIMITED TO THE DURATION OF THE
WARRANTY PERIOD. ALL OTHER EXPRESS OR IMPLIED
CONDITIONS, REPRESENTATIONS AND WARRANTIES ARE
DISCLAIMED. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. This limited warranty gives you specific legal rights, and you may also have other rights which vary by jurisdiction.
66
Appendix E
Disclaimer of Liabilities. TO THE EXTENT NOT PROHIBITED
BY APPLICABLE LAW, IN NO EVENT WILL CISCO BE LIABLE
FOR ANY LOST DATA, REVENUE OR PROFIT, OR FOR SPECIAL,
INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE
DAMAGES, REGARDLESS OF THE THEORY OF LIABILITY
(INCLUDING NEGLIGENCE), ARISING OUT OF OR RELATED
TO THE USE OF OR INABILITY TO USE THE PRODUCT,
SOFTWARE OR ANY SERVICES PROVIDED IN RESPECT
OF SUCH PRODUCT OR SOFTWARE, EVEN IF CISCO HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
TO THE EXTENT NOT PROHIBITED BY APPLICABLE LAW,
IN NO EVENT WILL CISCO’S LIABILITY EXCEED THE
AMOUNT PAID BY YOU FOR THE PRODUCT. IF YOU LIVE
IN THE EUROPEAN UNION, REFERENCES TO “SPECIAL,
INDIRECT, CONSEQUENTIAL, PUNITIVE OR INCIDENTAL
DAMAGES” SHALL MEAN ANY LOSSES WHICH (i) WERE NOT
REASONABLY FORESEEABLE BY BOTH PARTIES, AND/OR (ii)
WERE KNOWN TO YOU BUT NOT TO US AND/OR (iii) WERE
REASONABLY FORESEEABLE BY BOTH PARTIES BUT COULD
HAVE BEEN PREVENTED BY YOU SUCH AS, FOR EXAMPLE
(BUT WITHOUT LIMITATION), LOSSES CAUSED BY VIRUSES,
TROJANS OR OTHER MALICIOUS PROGRAMS, OR LOSS OF
OR DAMAGE TO YOUR DATA. The foregoing limitations will apply even if any warranty or remedy provided under this limited warranty fails of its essential purpose.
Technical Support. This limited warranty is neither a service nor a support contract. Information about
Cisco’s current technical support offerings and policies
(including any fees for support services) can be found at
www.linksysbycisco.com/support.
Export. Software, including technical data, may be subject to U.S. export control laws and regulations and/or export or import regulations in other countries. You agree to comply strictly with all such laws and regulations.
U.S. Government Users. The Software and Documentation qualify as “commercial items” as defined at 48 C.F.R. 2.101 and 48 C.F.R. 12.212. All Government users acquire the
Software and Documentation with only those rights herein that apply to non-governmental customers. Use of either the Software or Documentation or both constitutes agreement by the Government that the Software and
Documentation are “commercial computer software” and “commercial computer software documentation,” and constitutes acceptance of the rights and restrictions herein.
General Terms. This Agreement will be governed by and construed in accordance with the laws of the State of
California, without reference to conflict of laws principles.
The United Nations Convention on Contracts for the
International Sale of Goods will not apply. If any portion of this Agreement is found to be void or unenforceable, the remaining provisions will remain in full force and effect. This Agreement constitutes the entire agreement between the parties with respect to the Software and
Media Hub
Software End User License Agreement
supersedes any conflicting or additional terms contained in any purchase order or elsewhere.
Linksys, Cisco and the Cisco Logo and other trademarks contained in the Software and Documentation are trademarks or registered trademarks of Linksys, Cisco, its licensors and third parties, as the case may be. You may not remove or alter any trademark, trade names, product names, logo, copyright or other proprietary notices, legends, symbols or labels in the Software and
Documentation. This Agreement does not authorize you to use Cisco’s or its licensors’ names or respective trademarks.
END OF SCHEDULE 1
Schedule 2
Network Magic Features
Network Magic License Restrictions. Other than as set forth in this Agreement or as otherwise permitted by Cisco, you may not install or execute the Network
Magic Software on any non-personal computer product, including, but not limited to, a Web appliance, set top box, handheld device, phone, Web pad device, or any device running the Microsoft Windows CE operating system.
Terms of Service for Subscription Licenses. These Terms of Service only apply if you have obtained a subscription license to Network Magic as specified in your order. Such subscription licenses may subject you to fees which you are responsible for paying in order to continue to subscribe to the Services.
1. Network Magic Cancellation. You may cancel the
Services at any time. If you cancel the Services, Cisco will not be obligated to provide you any Network Magic product Upgrades. If you cancel the Services, Cisco may delete data relating to you or your use of the Services from Cisco or its suppliers’ servers. To the extent not prohibited by applicable law, you understand and agree that cancellation of your Services is your sole remedy with respect to any dispute with Cisco.
2. Modifications. Cisco may modify or cancel the terms of this Agreement or the price, content, or nature of the
Services (including discontinuing the Services program), upon notice to you. If Cisco modifies any of these terms, you may cancel the Service by providing written notice to Cisco via www.networkmagic.com/support of such cancellation and uninstalling the Software and discontinuing your use of the Service. Cisco may provide notice by e-mail, via Network Magic, or by publishing the changes on its Web site.
3. Email Notification. Cisco may send you email from time to time to let you know about new products and services that are available to you. You will be able to optout of receiving these emails using the link provided within the email. Cisco reserves the right, however, to
67
Appendix E
send you Service related email messages as long as you are a subscriber to the Service. If you wish to opt-out of receiving Service related email messages, you may cancel the Service by providing written notice via www.
networkmagic.com/support to Cisco of such cancellation and uninstalling the Software and discontinuing your use of the Service.
END OF SCHEDULE 2
Schedule 3
Open Source and Third Party Licenses
Schedule 3-A
If this Cisco product contains open source software licensed under Version 2 of the “GNU General Public
License” then the license terms below in this Schedule 3-A will apply to that open source software. The license terms below in this Schedule 3-A are from the public web site at
http://www.gnu.org/licenses/old-licenses/gpl-2.0.html
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright © 1989, 1991 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the
GNU General Public License is intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users. This General Public
License applies to most of the Free Software Foundation’s software and to any other program whose authors commit to using it. (Some other Free Software Foundation software is covered by the GNU Lesser General Public
License instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish), that you receive source code or can get it if you want it, that you can change the software or use pieces of it in new free programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you these rights or to ask you to surrender the rights. These restrictions translate to certain responsibilities for you if you distribute copies of the software, or if you modify it.
Media Hub
Software End User License Agreement
For example, if you distribute copies of such a program, whether gratis or for a fee, you must give the recipients all the rights that you have. You must make sure that they, too, receive or can get the source code. And you must show them these terms so they know their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author’s protection and ours, we want to make certain that everyone understands that there is no warranty for this free software. If the software is modified by someone else and passed on, we want its recipients to know that what they have is not the original, so that any problems introduced by others will not reflect on the original authors’ reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid the danger that redistributors of a free program will individually obtain patent licenses, in effect making the program proprietary.
To prevent this, we have made it clear that any patent must be licensed for everyone’s free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND
MODIFICATION
0. This License applies to any program or other work which contains a notice placed by the copyright holder saying it may be distributed under the terms of this General Public License. The “Program”, below, refers to any such program or work, and a “work based on the Program” means either the Program or any derivative work under copyright law: that is to say, a work containing the Program or a portion of it, either verbatim or with modifications and/ or translated into another language. (Hereinafter, translation is included without limitation in the term
“modification”.) Each licensee is addressed as “you”.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does.
68
Appendix E
1. You may copy and distribute verbatim copies of the
Program’s source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. .
2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the
Program, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modified files to carry prominent notices stating that you changed the files and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modified program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the
Media Hub
Software End User License Agreement
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code.
(This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.)
The source code for a work means the preferred form of the work for making modifications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code.
69
Appendix E
4. You may not copy, modify, sublicense, or distribute the Program except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense or distribute the Program is void, and will automatically terminate your rights under this License.
However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Program or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Program (or any work based on the
Program), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Program or works based on it.
6. Each time you redistribute the Program (or any work based on the Program), the recipient automatically receives a license from the original licensor to copy, distribute or modify the Program subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties to this License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Program at all. For example, if a patent license would not permit royalty-free redistribution of the Program by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system, which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance
Media Hub
Software End User License Agreement
on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
8. If the distribution and/or use of the Program is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Program under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Program specifies a version number of this
License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Program does not specify a version number of this License, you may choose any version ever published by the Free
Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose distribution conditions are different, write to the author to ask for permission. For software which is copyrighted by the Free Software
Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE PROGRAM, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM “AS IS” WITHOUT WARRANTY OF ANY
KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU.
SHOULD THE PROGRAM PROVE DEFECTIVE, YOU
ASSUME THE COST OF ALL NECESSARY SERVICING,
REPAIR OR CORRECTION.
70
Appendix E
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR
AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER,
OR ANY OTHER PARTY WHO MAY MODIFY AND/OR
REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE,
BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY
GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL
DAMAGES ARISING OUT OF THE USE OR INABILITY TO
USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO
LOSS OF DATA OR DATA BEING RENDERED INACCURATE
OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR
A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER
PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF
SUCH DAMAGES
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3-A
Schedule 3-B
If this Cisco product contains open source software licensed under Version 2.1 of the “GNU Lesser General Public
License” then the license terms below in this Schedule 3-B will apply to that open source software. The license terms below in this Schedule 3-B are from the public web site at http://www.gnu.org/licenses/old-licenses/lgpl-2.1.html
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright © 1991, 1999 Free Software Foundation, Inc.
51 Franklin Street, Fifth Floor, Boston, MA 02110-1301
USA
Everyone is permitted to copy and distribute verbatim copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU
General Public Licenses are intended to guarantee your freedom to share and change free software—to make sure the software is free for all its users.
This license, the Lesser General Public License, applies to some specially designated software packages—typically libraries—of the Free Software Foundation and other authors who decide to use it. You can use it too, but we suggest you first think carefully about whether this license or the ordinary General Public License is the better strategy to use in any particular case, based on the explanations below.
Media Hub
Software End User License Agreement
When we speak of free software, we are referring to freedom of use, not price. Our General Public Licenses are designed to make sure that you have the freedom to distribute copies of free software (and charge for this service if you wish); that you receive source code or can get it if you want it; that you can change the software and use pieces of it in new free programs; and that you are informed that you can do these things.
To protect your rights, we need to make restrictions that forbid distributors to deny you these rights or to ask you to surrender these rights. These restrictions translate to certain responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must give the recipients all the rights that we gave you. You must make sure that they, too, receive or can get the source code. If you link other code with the library, you must provide complete object files to the recipients, so that they can relink them with the library after making changes to the library and recompiling it. And you must show them these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we offer you this license, which gives you legal permission to copy, distribute and/ or modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for the free library. Also, if the library is modified by someone else and passed on, the recipients should know that what they have is not the original version, so that the original author’s reputation will not be affected by problems that might be introduced by others.
Finally, software patents pose a constant threat to the existence of any free program. We wish to make sure that a company cannot effectively restrict the users of a free program by obtaining a restrictive license from a patent holder. Therefore, we insist that any patent license obtained for a version of the library must be consistent with the full freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General Public License. This license, the GNU Lesser General Public License, applies to certain designated libraries, and is quite different from the ordinary General Public License. We use this license for certain libraries in order to permit linking those libraries into non-free programs.
When a program is linked with a library, whether statically or using a shared library, the combination of the two is legally speaking a combined work, a derivative of the original library. The ordinary General Public
License therefore permits such linking only if the entire combination fits its criteria of freedom. The Lesser General
71
Appendix E
Public License permits more lax criteria for linking other code with the library.
We call this license the “Lesser” General Public License because it does Less to protect the user’s freedom than the ordinary General Public License. It also provides other free software developers Less of an advantage over competing non-free programs. These disadvantages are the reason we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances.
For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library.
A more frequent case is that a free library does the same job as widely used non-free libraries. In this case, there is little to gain by limiting the free library to free software only, so we use the Lesser General Public License.
In other cases, permission to use a particular library in nonfree programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users’ freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow. Pay close attention to the difference between a “work based on the library” and a
“work that uses the library”. The former contains code derived from the library, whereas the latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE
TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION
AND MODIFICATION
0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser
General Public License (also called “this License”). Each licensee is addressed as “you”.
A “library” means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables.
The “Library”, below, refers to any such software library or work which has been distributed under these terms.
A “work based on the Library” means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it,
Media Hub
Software End User License Agreement
either verbatim or with modifications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term
“modification”.)
“Source code” for a work means the preferred form of the work for making modifications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface definition files, plus the scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the
Library’s complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library.
You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the
Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modified work must itself be a software library.
b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License.
d) If a facility in the modified Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful.
72
Appendix E
(For example, a function in a library to compute square roots has a purpose that is entirely well-defined independent of the application. Therefore, Subsection
2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)
These requirements apply to the modified work as a whole. If identifiable sections of that work are not derived from the Library, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Library, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Library.
In addition, mere aggregation of another work not based on the Library with the Library (or with a work based on the Library) on a volume of a storage or distribution medium does not bring the other work under the scope of this License.
3. You may opt to apply the terms of the ordinary GNU
General Public License instead of this License to a given copy of the Library. To do this, you must alter all the notices that refer to this License, so that they refer to the ordinary GNU General Public License, version
2, instead of to this License. (If a newer version than version 2 of the ordinary GNU General Public License has appeared, then you can specify that version instead if you wish.) Do not make any other change in these notices.
Once this change is made in a given copy, it is irreversible for that copy, so the ordinary GNU General
Public License applies to all subsequent copies and derivative works made from that copy.
This option is useful when you wish to copy part of the code of the Library into a program that is not a library.
4. You may copy and distribute the Library (or a portion or derivative of it, under Section 2) in object code or executable form under the terms of Sections 1 and
2 above provided that you accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of
Sections 1 and 2 above on a medium customarily used for software interchange.
Media Hub
Software End User License Agreement
If distribution of object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place satisfies the requirement to distribute the source code, even though third parties are not compelled to copy the source along with the object code.
5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a “work that uses the Library”. Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
However, linking a “work that uses the Library” with the Library creates an executable that is a derivative of the Library (because it contains portions of the
Library), rather than a “work that uses the library”. The executable is therefore covered by this License. Section
6 states terms for distribution of such executables.
When a “work that uses the Library” uses material from a header file that is part of the Library, the object code for the work may be a derivative work of the Library even though the source code is not. Whether this is true is especially significant if the work can be linked without the Library, or if the work is itself a library. The threshold for this to be true is not precisely defined by law.
If such an object file uses only numerical parameters, data structure layouts and accessors, and small macros and small inline functions (ten lines or less in length), then the use of the object file is unrestricted, regardless of whether it is legally a derivative work. (Executables containing this object code plus portions of the Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object code for the work under the terms of Section 6. Any executables containing that work also fall under Section 6, whether or not they are linked directly with the Library itself.
6. As an exception to the Sections above, you may also combine or link a “work that uses the Library” with the
Library to produce a work containing portions of the
Library, and distribute that work under terms of your choice, provided that the terms permit modification of the work for the customer’s own use and reverse engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used in it and that the
Library and its use are covered by this License. You must supply a copy of this License. If the work during execution displays copyright notices, you must include the copyright notice for the Library among them, as well as a reference directing the user to the copy of this
License. Also, you must do one of these things:
73
Appendix E
a) Accompany the work with the complete corresponding machine-readable source code for the Library including whatever changes were used in the work (which must be distributed under Sections 1 and 2 above); and, if the work is an executable linked with the Library, with the complete machine-readable “work that uses the
Library”, as object code and/or source code, so that the user can modify the Library and then relink to produce a modified executable containing the modified Library. (It is understood that the user who changes the contents of definitions files in the
Library will not necessarily be able to recompile the application to use the modified definitions.) b) Use a suitable shared library mechanism for linking with the Library. A suitable mechanism is one that
(1) uses at run time a copy of the library already present on the user’s computer system, rather than copying library functions into the executable, and
(2) will operate properly with a modified version of the library, if the user installs one, as long as the modified version is interface-compatible with the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give the same user the materials specified in Subsection 6a, above, for a charge no more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place.
e) Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
For an executable, the required form of the “work that uses the Library” must include any data and utility programs needed for reproducing the executable from it. However, as a special exception, the materials to be distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other proprietary libraries that do not normally accompany the operating system.
Such a contradiction means you cannot use both them and the Library together in an executable that you distribute.
Software End User License Agreement
7. You may place library facilities that are a work based on the Library side-by-side in a single library together with other library facilities not covered by this License, and distribute such a combined library, provided that the separate distribution of the work based on the
Library and of the other library facilities is otherwise permitted, and provided that you do these two things: a) Accompany the combined library with a copy of the same work based on the Library, uncombined with any other library facilities. This must be distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a work based on the Library, and explaining where to find the accompanying uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as expressly provided under this License. Any attempt otherwise to copy, modify, sublicense, link with, or distribute the Library is void, and will automatically terminate your rights under this License. However, parties who have received copies, or rights, from you under this License will not have their licenses terminated so long as such parties remain in full compliance.
9. You are not required to accept this License, since you have not signed it. However, nothing else grants you permission to modify or distribute the Library or its derivative works. These actions are prohibited by law if you do not accept this License. Therefore, by modifying or distributing the Library (or any work based on the
Library), you indicate your acceptance of this License to do so, and all its terms and conditions for copying, distributing or modifying the Library or works based on it.
10. Each time you redistribute the Library (or any work based on the Library), the recipient automatically receives a license from the original licensor to copy, distribute, link with or modify the Library subject to these terms and conditions. You may not impose any further restrictions on the recipients’ exercise of the rights granted herein. You are not responsible for enforcing compliance by third parties with this
License.
Media Hub
74
Appendix E
11. If, as a consequence of a court judgment or allegation of patent infringement or for any other reason (not limited to patent issues), conditions are imposed on you (whether by court order, agreement or otherwise) that contradict the conditions of this License, they do not excuse you from the conditions of this License. If you cannot distribute so as to satisfy simultaneously your obligations under this License and any other pertinent obligations, then as a consequence you may not distribute the Library at all. For example, if a patent license would not permit royalty-free redistribution of the Library by all those who receive copies directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this
License.
12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this
License incorporates the limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public
License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns.
Each version is given a distinguishing version number.
If the Library specifies a version number of this License which applies to it and “any later version”, you have the option of following the terms and conditions either of that version or of any later version published by the Free
Software Foundation. If the Library does not specify a
Media Hub
Software End User License Agreement
license version number, you may choose any version ever published by the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the
Free Software Foundation, write to the Free Software
Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE,
THERE IS NO WARRANTY FOR THE LIBRARY, TO THE
EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT
WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT
HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY “AS IS” WITHOUT WARRANTY OF ANY KIND,
EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD
THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE
COST OF ALL NECESSARY SERVICING, REPAIR OR
CORRECTION.
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW
OR AGREED TO IN WRITING WILL ANY COPYRIGHT
HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY
AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED
ABOVE, BE LIABLE TO YOU FOR DAMAGES,
INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES ARISING OUT OF THE
USE OR INABILITY TO USE THE LIBRARY (INCLUDING
BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY
YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY
TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF
SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
END OF SCHEDULE 3-B
75
Appendix E
Schedule 3-C
OPENSSL LICENSE
If this Cisco product contains open source software licensed under the OpenSSL license:
This product includes software developed by the
OpenSSL Project for use in the OpenSSL Toolkit.
(http://www.openssl.org/).
This product includes cryptographic software written by Eric Young ([email protected]).
This product includes software written by Tim Hudson
In addition, if this Cisco product contains open source software licensed under the OpenSSL license then the license terms below in this Schedule 3-C will apply to that open source software. The license terms below in this Schedule 3-C are from the public web site at
http://www.openssl.org/source/license.html.
The OpenSSL toolkit stays under a dual license, i.e. both the conditions of the OpenSSL License and the original
SSLeay license apply to the toolkit. See below for the actual license texts. Actually both licenses are BSD-style
Open Source licenses. In case of any license issues related to OpenSSL please contact [email protected].
OpenSSL License
Copyright © 1998-2007 The OpenSSL Project. All rights reserved.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the
OpenSSL Toolkit. (http://www.openssl.org/)”
4. The names “OpenSSL Toolkit” and “OpenSSL Project” must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact [email protected].
5. Products derived from this software may not be called
“OpenSSL” nor may “OpenSSL” appear in their names without prior written permission of the OpenSSL
Project.
Media Hub
Software End User License Agreement
6. Redistributions of any form whatsoever must retain the following acknowledgment: “This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl.org/)”
THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT
``AS IS’’ AND ANY EXPRESSED OR IMPLIED WARRANTIES,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT
SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE
LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL,
EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING,
BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE
GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS;
OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND
ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR
OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF
THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF
SUCH DAMAGE
This product includes cryptographic software written by
Eric Young ([email protected]). This product includes software written by Tim Hudson ([email protected]).
Original SSLeay License
Copyright © 1995-1998 Eric Young ([email protected])
All rights reserved.
This package is an SSL implementation written by Eric
Young ([email protected]).
The implementation was written so as to conform with
Netscape’s SSL.
This library is free for commercial and non-commercial use as long as the following conditions are adhered to.
The following conditions apply to all code found in this distribution, be it the RC4, RSA, lhash, DES, etc., code; not just the SSL code. The SSL documentation included with this distribution is covered by the same copyright terms except that the holder is Tim Hudson (tjh@cryptsoft.
com).
Copyright remains Eric Young’s, and as such any Copyright notices in the code are not to be removed.
If this package is used in a product, Eric Young should be given attribution as the author of the parts of the library used. This can be in the form of a textual message at program startup or in documentation (online or textual) provided with the package.
Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the copyright notice, this list of conditions and the following disclaimer.
76
Appendix E
2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.
3. All advertising materials mentioning features or use of this software must display the following acknowledgement:
“This product includes cryptographic software written by Eric Young ([email protected])”
The word ‘cryptographic’ can be left out if the routines from the library being used are not cryptographic related.
4. If you include any Windows specific code (or a derivative thereof) from the apps directory (application code) you must include an acknowledgement: “This product includes software written by Tim Hudson (tjh@ cryptsoft.com)”
THIS SOFTWARE IS PROVIDED BY ERIC YOUNG ``AS IS’’
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING,
BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR
PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE
AUTHOR OR CONTRIBUTORS BE LIABLE FOR ANY
DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY,
OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY
OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
The license and distribution terms for any publicly available version or derivative of this code cannot be changed. i.e. this code cannot simply be copied and put under another distribution license [including the GNU Public License.]
END OF SCHEDULE 3-C
Software End User License Agreement
Media Hub
9051310A-JL
77
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project