advertisement
PP-55
Getting Started Manual
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
..
Contents
Magnetic Card Reader (MS Version only)........................................................... 11
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
..
Getting Started
The IPC PP-55 allows you to print information from your PDA or Smartphone. This
Getting Started Manual provides you with a short list of tasks to get your PP-55 up and running. For more in depth explanation, consult the full user’s manual on the enclosed CD ROM or can be downloaded at: http://www.ipcprint.com/support/downloads/mobility/supdw_thermpp55d.asp
Quick Start:
Steps What to do Purpose
Where to find more information
1
2
3
Charge the PP-55 rechargeable battery pack as recommended in this manual.
The Lithium Ion battery pack should be fully charged before used to ensure long battery life.
Install Print Software onto PDA and Desktop.
Different device types such as
Palm, PocketPC, and
BlackBerry require different software to run the
PP-55.
Charging Battery,
Page 6 in User’s manual
Installing PrintSuite,
Page 12 in User’s manual
Load PP-55 print media
(Thermal Paper)
PP-55 requires Thermal paper for printing.
Loading Paper,
Page 7 in User’s manual
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Table 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 2
.
.
.
..
About Your PP-55
♦ PP-55 Overall View
Paper cover Battery cover Device carrier
ON/OFF LED indicator
♦ Control Panel
Battery
charge LED
indicator
ON/OFF
and Paper Feed
button Serial / USB Port
♦ Battery recharge
Adapter inlet
NOTE: With a fully charged
battery, PP-55 can print
out more than 5000 inches
of (alpha numeric) data.
To recharge the battery, plug AC/DC
adapter supplied with printer and
charge until the red battery charge
indicator turns to green.
Prolonged periods of storage can
cause a drop in the power of the
printer’s rechargeable battery!
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Adapter inlet
Figure 1
Page 3
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
Charging Battery
Charging PP-55:
The PP-55 uses a Lithium Ion rechargeable battery pack. Before first use, the PP-
55 battery pack should be charged for at least 4 hours.
To prevent electrical damage to the printer and/or battery pack, please use approved
AC/DC adapter only.
AC Adapter
Adapter inlet
Figure 2
Charging PP-55 & PDA:
The PP-55 has a built-in charging circuit to enable the charging of PDA device while in the PP-55’s cradle. PDA charging only occurs when the external AC/DC adaptor is connected to PP-55 adapter inlet.
Solid RED = charging
Solid GREEN = fully charged (~4 hrs.)
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Figure 3
Page 4
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
Loading Paper
The PP-55 uses a drop-and-load design making paper loading easy and trouble free. To load paper, simply remove the paper cover and drop in the new roll as shown in the steps below.
Make sure that the paper is placed in the printer as shown in step 2 below.
Open paper cover holder with both
fingers and remove the remaining
part of the old paper roll.
Place the paper
roll and cover in
position.
Press with both
fingers to click cover
of shell in place.
Make sure that the pa-
per is fed out from the
printer at a right angle
If not pull paper verti-
cally by hand.
Figure 4
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 5
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
..
Compatible Mobile Devices
The PP-55 portable thermal printer is designed specifically for use with the world’s most popular PDA devices.
The PP-55 can be used in a variety of applications where hardcopy printouts are required.
End Users – for printing Emails, HTML pages, Graphics files, Clipboard data, text only files, Screen Captures, and more.
Manufacturers – for shipping & receiving goods, date and time printing, inventory control and W.I.P. management.
Distributors – for marking prices, sales receipts, route deliveries.
POS – for mobile sales receipts and credit card verifications in POS application.
The following is a list of devices that the PP-55 currently supports.
Compatible products:
No.
PDA
Device
Operation System
(OS)
Device Type
(for attachment)
1 Tungsten C, W, Zire 71 Palm Device Type #3
2 Tungsten T, T2
3 Treo 180, 270, 300, 600
4 Kyocera 7135
5
HP iPAQ 3800, 3900,
4200, 5100, 5400,
5500, 2200
Palm
Palm
Palm
Pocket PC
Device Type #4
Device Type #1
Device Type #1
Device Type #1
6 Samsung i700
7
RIM 957, 5810, 6200,
6510, 6700, 7700
8 RIM 7200, 7510
Pocket PC
BlackBerry
Device Type #1
Device Type #1
BlackBerry Device Type #5
Table 2
Devices are added continually. For updates on supported device, visit our web site at www.ipcprint.com
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 6
.
.
.
..
Attaching Mobile Device
The PP-55 has several versions designed to be used with specific devices.
See section on compatible products to make sure your device will work with the PP-55.
Care must be taken to ensure that the PP-55 cradle connector and PDA connector are not accidentally damaged. The figures below show how to attach the different device to the printer and how to remove the device from the printer.
Figure 5
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 7
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
Attaching Mobile Device
Figure 6
Device Type #5
Figure 7
Although the PP-55 cradle is designed to hold the device in place, this does not prevent the device from accidentally slipping out if the printer is held in the position below.
Figure 8
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 8
.
.
.
..
Installing Print Software
The PP-55 comes with software package used for printing from your handheld device. Also included in the software package are Printer Driver and SDKs
(Software Development Kits) for several IDE (Integrated Development Environment).
The following steps explain installing the PP-55 print software.
1). PP-55 software package must be installed onto the PC before it can be loaded onto a specific device.
2). Using the device PC sync manager, device specific print utilities must be installed onto the device.
The print software installation program “PrintSuite.EXE” can be found on the CD that is supplied with the PP-55 or at our developer web site at: http://www.ipcprint.com/support/downloads/mobility/supdw_thermpp55.asp
For detailed information on print software installation please refer to the PP-55
User’s Manual on the CD or download it from the developer site indicated above.
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 9
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
Printer Status & Operating Modes
The PP-55 uses LEDs to indicate various conditions of operation. This may be charging, printing, out of paper or error conditions. The following explains these conditions and LED indication.
ON/OFF LED Charging LED
Feed Button
Printer Status
Solid GREEN = Battery at full charge
Battery Charging LED
Solid RED = Battery charging
Solid GREEN = Power ON
Solid RED = Low battery
ON/OFF LED
Slow Blinking = High temperature error
Fast Blinking = Printer out of paper
Table 3
The PP-55’s paper feed switch/button is used for entering various printer modes.
These modes can be used to assist developers in debugging problems related to programming and communication. The following explain how to access the various operating modes.
Operation Modes
Short Push N/A Paper feed
Push and Hold - release after the number of beeps
1 - beep Self-test
2 - beeps Hex dump
3 - beeps Reserved – For factory use only
4 - beeps Reserved – For factory use only
5 - beeps Reserved – For factory use only
Table 4
Note: Care must be taken when entering operating modes to prevent the clearing of factory preset configuration information.
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Page 10
.
.
.
.
.
Magnetic Card Reader
(MS Version only)
The PP-55MS has a built-in magnetic card reader. The card reader incorporates a (3)-track magnetic read head requiring a single swipe to read field data from all three tracks.
Magnetic Card Reader
Reader Activation
(Indicator)
Figure 9
The magnetic read head faces towards the PDA cradle. When placing the card into the reader, the magnetic strip must be facing away from the PDA’s cradle as show in the figure below. Keep the edge of the card flat on the inner base of the reader to ensure that the magnetic strip passes over the read head evenly.
Magnetic surface
(Direction)
Figure 10
Developer Notes:
Integrating the magnetic card reader feature into an application requires the use of the PP-55 SDK’s. For detailed information on integrating the card reader feature, refer to the User’s Manual for your specific device type.
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 11
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
.
.
Barcode Reader
(MS BC Version only)
The PP-55MS BC offers a version with built-in barcode reader. The barcode reader incorporates a linear image scan head and is capable of reading 1D barcodes.
Barcode Reader
Figure 11
The effective reading distance of the PP-55 barcode reader is approximately
10 cm. To scan a barcode, position the read head as close to the barcode label as possible. Activate the scanner then slowly pull back the unit increasing the distance between the barcode and read head until the barcode has been read by the scanner.
Effective Reading
Distance (~10 cm)
Figure 12
Developer Notes:
Integrating the barcode reader feature into an application requires the use of the PP-55 SDK’s. For detailed information on integrating the barcode reader feature, refer to the User’s Manual for your specific device type.
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 12
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
..
Troubleshooting
If you’re having a printing problem refer to the table below for possible causes.
Item Problem
1
Paper feeds after issuing a print job but no printed text visible on paper.
Thermal media is specially coated on outside of roll. Remove paper roll and reload properly. See section
“Loading Paper” for details on loading paper.
Paper cover not installed properly.
See section “Loading Paper” for details on replacing paper cover.
2
3
4
On-line LED blinks fast continuously.
Text and/or graphics are printed very light.
Printer out of paper.
Paper not properly loaded. See section “Loading Paper” for details on loading paper.
Battery level low. Recharge battery pack.
Thermal media not imaging correctly. Verify that you are using the recommended thermal media.
Palm Device – PrintManager
Printer icon battery shows low or no voltage but PP-55 battery is fully charged.
Verify Control Panel configuration set to PP-55 and 115200 BPS. See section “Control Panel” for details on changing configuration.
5
Strange characters are printed when printing.
Serial communication speed (Baud
Rate) not same as PDA.
6 On-line LED always solid RED
Battery voltage low. See section on charging battery pack.
7
Printer stops responding to print and paper feed commands.
Table 5
Remove battery for 5 seconds and reconnect battery.
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 13
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
.
.
.
..
Contact Information
National Sales Headquarters: Infinite Peripherals, Inc.
Midwest Sales Office: www.ipcprint.com
Infinite Peripherals, Inc.
Suite C
East Coast Sales Office
Technical Support: www.ipcprint.com
Infinite Peripherals, Inc.
700-76 Broadway, #136
Westwood, NJ 07675
Phone: 201-647-3025
Fax: 866-247-1935 www.ipcprint.com
Infinite Peripherals, Inc. www.ipcprint.com
Infinite Peripherals, Inc. www.ipcprint.com
PP-55 Getting Started Version 1.08
Page 14
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 1 Cover
- 2 Contents
- 3 Getting Started
- 4 About Your PP-55
- 5 Charging Battery
- 6 Loading Paper
- 7 Compatible Mobile Devices
- 7 Compatible products:
- 8 Attaching Mobile Device
- 10 Installing Print Software
- 11 Printer Status & Operating Modes
- 12 Magnetic Card Reader (MS Version only)
- 13 Barcode Reader (MS BC Version only)
- 14 Troubleshooting
- 15 Contact Information