Infinity Speaker PS28 User's Manual

Infinity Speaker PS28 User's Manual
PS Series
PS28 Subwoofer
SERVICE MANUAL
Infinity Systems, Inc.
250 Crossways Park Dr.
Woodbury, New York 11797
Rev1 3/2007
PS series PS28 subwoofer
- CONTENTS -
BASIC SPECIFICATIONS
…………………..……………..1
DETAILED SPECIFICATIONS…………………..……….…..2
PACKAGING……………….……………………….…....….…4
CONTROLS AND CONNECTIONS…………..…….………..5
OPERATION….……………………………………………..….7
EXPLODED VIEW/PARTS LIST
…………….….…....……8
TEST SET UP AND PROCEDURE………………..…....……9
BLOCK DIAGRAM…………………………..………….…..…10
TROUBLESHOOTING FLOW CHART………………..........12
ELECTRICAL PARTS LIST (120v) ………………………….13
PCB DRAWINGS……………….……………………………..17
SEMICONDUCTOR PINOUTS……….……………….……..21
SCHEMATICS (120v)………………………………………...22
Basic Specifications
PS28 Powered Subwoofer
Frequency Response:
35Hz – 150Hz (±3dB)
Maximum Amplifier Output:
150 Watts RMS (20Hz – 150Hz, with ≤ 0.1% THD)
300 Watts Peak
Crossover Frequency:
50Hz – 150Hz, 24dB/octave, continuously variable
Driver:
8" (200mm)
Dimensions (H x W x D):
17-7/8" x 10-5/8" x 16-1/2" (454mm x 270mm x 419mm)
Weight:
31.7 lb (14.4kg)
Infinity continually strives to update and improve existing products, as well as create new ones. The specifications
and construction details in this and related Infinity publications are therefore subject to change without notice.
1
PS series PS28 subwoofer
INFINITY PRIMUS PS28 150W Powered Sub/ Plate Amp
LINE VOLTAGE
US 120VAC/60Hz
Europe 220-240VAC, 50-60Hz
Yes/No
Yes
Yes
Hi/Lo Line
108-132
220-230
Unit
Vrms
Vrms
Specification
Unit
QA Test Limits
Amp Section
Type (Class AB, D, other)
Type (Class AB, D, other)
AB
G
AB
G
n/a
n/a
120V model
230V Model
Rated Load Impedance
System average impedance
Voice coil DCR
Rated Output Power
[email protected] Rated Power
THD @ 1 Watt
DC Offset
4
8.79
4.35
100
0.5
0.1
10
Ohms
Ohms
Ohms
Watts
%
%
mV-DC
n/a
n/a
n/a
95
1
0.3
50
Nominal
Average impedance from 10 to 500Hz
Damping factor
>100
Dynamic power RMS
Highest RMS value
125
152
Watts
Watts
Reference
Reference
Input Sensitivity
Input Frequency
Line Input (L&R)
LFE Input
System Gain (Line input)
System gain (LFE input)
50
16.5
11.7
41
44
Hz
mVrms
mVrms
dB
dB
50
±2dB
±2dB
±1dB
±1dB
Signal to Noise
SNR-A-Weighted
SNR-unweighted
SNR @ 1W-unweighted
100
85
65
dBA
dBr
dBr
1
Parameter
Notes
Normal Operation
Normal Operation
Conditions
Single input driven
22K filter
22K filter
@ Speaker Output
40
Notes
External Sink required for Class AB
Impedance used for electrical
measurements
Reference
Measured at speaker terminals, Output
power 90 Watts
AVG Power over the first 4 consecutive
peaks, when tested with a burst siganl 3/20
at 50 Hz
Nominal Freq.
To 1W
To 1W
G=118
G=165
Single input driven, AP Zo=600 Ohms
LFE input driven only, AP Zo=600 Ohms
Single input driven, AP Zo=600 Ohms
LFE input driven only, AP Zo=600 Ohms
85
80
60
rel. to rated power
rel. to rated power
rel. to 1W Output
A-Weighting filter
22K filter
22K filter
mVrms(max)
1.5
Volume @max, w/ A/P Swept Bandpass
Measurement (Line freq.+ harmonics)
>10
K ohms
n/a
Nominal
Filters
Low Pass (fixed or variable)
Subsonic filter (HPF)
Variable
-Hz
±2dB
±2dB
Limiter (yes/no)
THD at Max. Output Power
YES
<1
-%
Functional
Functional
Features
Line Level inputs (L&R)
LFE Input
Phase Switch (yes/no)
Volume pot Taper (lin/log)
Variable crossover
ATO
LED indicator
YES
YES
YES
LOG
YES
YES
YES
Input Configuration
Line In (L,R)
Line level in LFE
L ,R
LFE
Signal Sensing (ATO)
Auto-Turn-On (yes/no)
ATO Level @ 50 Hz
ATO Level @ 1 KHz
Residual Noise Floor
Input Impedance
Line input L&R , LFE
Crossover range 50-150 Hz
Fixed
Functional
Functional
Functional
Functional
Functional
Functional
Functional
Dual RCA conenctor (RED-WHT)
Single input (Yellow color)
--
Functional
Functional
RCA inputs: L , R Summed to Mono
YES
1
1
-mV
mV
Functional
Functional
Functional
ATO Turn-on time
5
ms
Functional
One input driven
One input driven
Amp connected and AC on, then input
signal applied
Auto Mute/ Turn-OFF Time
10
minutes
Functional
T before muting, after signal is removed Auto turn of time (T) must be 5 > T <15
Power on Delay time
3
sec.
Functional
AC Power Applied
Transients/Pops
ATO Transient
Turn-on Transient
5
50
mV-peak
mV-peak
10
100
Located at the amplifier panel
@ Speaker Outputs
@ Speaker Outputs
2
AC Line cycled from OFF to ON
PS series PS28 subwoofer
Parameter
Turn-off Transient
Specification
Unit
QA Test Limits
50
mV-peak
100
Conditions
Notes
@ Speaker Outputs
AC Line cycled from ON to OFF
Maximum allowable input power under
nominal Input voltage and frequency, HOT
or COLD operation.
100 Watts @ 4 Ohms nominal line voltage
Efficiency
Stand-by Input Power
Power [email protected] power
12
195
Watts
Watts
15
210
@ nom. line voltage
@ nom. line voltage
Protection
Short Circuit Protection
YES
--
Functional
Direct short at output
65 deg. C
YES
---
Functional
Functional
@1/8 max unclipped Power
DC present at Speaker Out leads
2.5
1.25
Amps
Amps
Thermal Protection
DC Offset Protection
Line Fuse Rating
120 VAC
230 VAC
Type-T or Slo Blo
Type-T, Low breaking capacity
3
Temperature rise should not exceed 35K
rise
Relay or crowbar (for driver/fire protection)
External fuse with UL/SEMKO rated holder
PS series PS28 subwoofer
4
Primus PS28 (120V) OM
10/2/06
10:24 AM
Page 4
PS series PS28 subwoofer
CONTROLS AND CONNECTIONS
Rear Panel
¡ Subwoofer-Level Control
™ Crossover Adjustment
®
¡
£ Phase Switch
¢ LFE Input
™
∞ Line-Level Inputs
§ Power Switch
£
¢
∞
§
FUSE
T 2.5A L 250V
TYPE
PS28 (120V)
5
AC~
120V
60HZ
200 Watts
Primus PS28 (120V) OM
10/2/06
10:24 AM
Page 5
PS series PS28 subwoofer
SUBWOOFER CONNECTIONS
CHOOSE THE SUBWOOFER CONNECTION THAT IS MOST SUITABLE FOR YOUR RECEIVER/PROCESSOR
If you have a Dolby® Digital or DTS®
receiver/processor with a low-frequency
effects (LFE) or subwoofer output:
SUBWOOFER OR
LFE OUTPUT
If your receiver/processor does
not contain a Dolby Digital or DTS
processor but has a subwoofer output:
RECEIVER/PROCESSOR
L
R
NOTE: Some receivers have one
subwoofer output. In that case, it is
recommended that you use a Y connector
(not included) to maximize performance.
6
PS28 (120V)
Primus PS28 (120V) OM
10/2/06
10:24 AM
Page 6
PS series PS28 subwoofer
OPERATION
Power On
Crossover Adjustments
Plug your subwoofer’s AC cord into a wall outlet. Do not use the
outlets on the back of the receiver.
The Crossover Adjustment Control ™ determines the highest
frequency at which the subwoofer reproduces sounds. If your main
speakers can comfortably reproduce some low-frequency sounds,
set this control to a lower frequency setting, between 50Hz
and 100Hz.This will concentrate the subwoofer’s efforts on the
ultradeep bass sounds required by today’s films and music. If you
are using smaller bookshelf speakers that do not extend to the
lower bass frequencies, set the Crossover Adjustment Control to
a higher setting, between 120Hz and 150Hz.
Initially set the Subwoofer-Level Control ¡ to the “min”
position.
Turn on your sub by pressing the Power Switch § on the rear
panel.Turn on your entire audio system and start a CD or movie
soundtrack at a moderate level.
Auto On/Standby
NOTE: This control will have no effect if the LFE Input ¢ is used.
If you have a Dolby Digital or DTS processor/receiver, the Low-Pass
Frequency is set by the processor/receiver. Consult your owner’s
manual to learn how to view or change this setting.
With the Power Switch § in the ON position, the LED on the
rear panel will remain lit in red or green to indicate the
On/Standby mode of the subwoofer.
RED = STANDBY (No signal detected, Amp Off)
MAINTENANCE AND SERVICE
GREEN = ON (Signal detected, Amp On)
The subwoofer will automatically enter the Standby mode after
approximately 10 minutes when no signal is detected from your
system.The subwoofer will then power ON instantly when a
signal is detected. During periods of normal use, the Power
Switch § can be left on.You may turn off the Power Switch §
for extended periods of nonoperation, e.g., when you are
away on vacation.
The enclosure may be cleaned using a soft cloth to remove
fingerprints or to wipe off dust.
The grille may be gently vacuumed. Stains may be removed with
an aerosol cleaner, following its instructions. Do not use any
solvents on the grille.
All wiring connections should be inspected and cleaned or
remade periodically.The frequency of maintenance depends on
the metals involved in the connections, atmospheric conditions,
and other factors, but once per year is the minimum.
Adjust Level
Turn your Subwoofer-Level Control ¡ up to the “5” position
(halfway). If no sound emanates from the subwoofer, check the
AC-line cord and input cables.Are the connectors on the cables
making proper contact? Is the AC plug connected to a “live”
receptacle? Has the Power Switch § been pressed to the “On”
position? Once you have confirmed that the subwoofer is active,
proceed by playing a CD, record or cassette. Use a selection that
has ample bass information.
In the event that your subwoofer ever needs service,
contact your local Infinity dealer or distributor or visit
www.infinitysystems.com for a service center near you.
Set the overall volume control of the preamplifier or stereo to a
comfortable level. Adjust the Subwoofer-Level Control ¡ until
you obtain a pleasing blend of bass. Bass response should not
overpower the room but rather be adjusted so there is a
harmonious blend across the entire musical range. Many
users have a tendency to set the subwoofer volume too loud,
adhering to the belief that a subwoofer is there to produce lots
of bass.This is not entirely true. A subwoofer is there to enhance
bass, extending the response of the entire system so the bass
can be felt as well as heard. However, overall balance must
be maintained or the music will not sound natural. An
experienced listener will set the volume of the subwoofer so its
impact on bass response is always there but never obtrusive.
Phase Control
The Phase Switch £ determines whether the subwoofer
speaker’s piston-like action moves in and out with the main
speakers, 0,˚ or opposite the main speakers, 180.˚Proper phase
adjustment depends on several variables such as room size,
subwoofer placement and listener position. Adjust the phase
switch to maximize bass output at the listening position.
7
PS series PS28 subwoofer
8
PS series PS28 subwoofer
PS28 Test Set Up and Procedure
SYSTEM AURAL SWEEP TEST
Equipment needed:
• Function/signal generator/sweep generator
• Integrated Amplifier
• Multimeter
• Speaker cables
General Unit Function (UUT = Unit Under Test)
Switches/knobs on the amplifier faceplate:
Low Pass Frequency Adjust full CW (150Hz)
Phase switch – either position
1. From the signal generator, Connect both right and left line level inputs (RCA) – not the LFE jack - to signal
generator and UUT. Use Y-cable if necessary from mono source.
2. On the amplifier, turn the LEVEL control full Counterclockwise (Min).
3. Turn on generator, adjust to 100mV, 50 Hz.
4. Plug in UUT; turn the power switch ON. Turn LEVEL control full Clockwise (Max).
5. LED should now be Green; immediate bass response should be heard and felt from rear port tube opening.
Sweep Function
1. Follow steps 1-5 above, using a sweep generator as a signal source.
2. Sweep generator from 20Hz to 1kHz. Listen to the cabinet and drivers for any rattles, clicks, buzzes or
any other noises. If any unusual noises are heard, remove woofer and test.
Driver Function (Woofer)
1. Remove woofer from cabinet; detach + and - wire clips.
2. Check DC resistance of woofer; it should be 4.4 ohms±10%.
3. Connect a pair of speaker cables to driver terminals. Cables should be connected to an integrated
amplifier fed by a signal generator. Turn on generator and adjust so that speaker level output is 5.0V.
4. Sweep generator from 20Hz to 1kHz. Listen to driver for any rubbing, buzzing, or other unusual noises.
9
PS series PS28 subwoofer
10
PS series PS28 subwoofer
11
PS series PS28 subwoofer
PS28
Troubleshooting Flow Chart
AMP no signal out
no
yes
Check Fuse,Transformer,
D110, etc
DC voltage check ±Vcc
yes
yes
no
Check Q117,118,119,D109 etc
Check+/-15VDC
yes
yes
LED red
LED light green or red
LED light green
Check,Q206,Q207,U203 etc
yes
yes
Check U201
pin14 signal
no
Check U202 pin14 signal
yes
yes
CheckU201,U202,VR201
VR202. etc
no
no
Check limiter board C304
Check U301,R343,R344 ,
C340,Q301,Q302, etc
yes
yes
Test R121,R122 signal
yes
no
Check ,+VCC& -VCC
Check J123,J124 etc
DC voltage
no
yes
yes
Check RY101,D102,Q113,Q114 etc
Check Q107,Q108,Q105,
Q106,Q103,Q104,U101,etc
yes
no
Check U101,Q115,Q116,R138 etc
Set R138 to R140’S
Voltage is 0.51VDC
yes
yes
Check P102 signal
Amp ass’y is OK, Finish
12
PS series PS28 subwoofer
PS 28 (120v) Electrical Parts List
Part Number
Description
Qty Reference Designator
PREAMP PCB
Resistors
110-14122j26-e
110-16102j26-e
Resistor 1.2K 1/4W ±5% CF 26mm (RoHS)
Resistor 1K 1/6W ±5% CF 26mm (RoHS)
1
5
110-16103j26-e
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
12
110-16104j26-e
110-16105j26-e
110-16123j26-e
110-16183j26-e
110-16205j26-e
110-16223j26-e
110-16224j26-e
110-16273j26-e
110-16333j26-e
110-16472j26-e
110-16473j26-e
110-16474j26-e
110-16512j26-e
110-16562j26-e
116-164531f26-e
116-164991f26-e
115-h203b208-e
115-h503a104-e
Resistor 100K 1/6W ±5% CF 26mm (RoHS)
Resistor 1M 1/6W ±5% CF 26mm (RoHS)
Resistor 12K 1/6W ±5% CF 26mm (RoHS)
Resistor 18K 1/6W ±5% CF 26mm (RoHS)
Resistor 2M 1/6W ±5% CF 26mm (RoHS)
Resistor 22K 1/6W ±5% CF 26mm (RoHS)
Resistor 220K 1/6W ±5% CF 26mm (RoHS)
Resistor 27K 1/6W ±5% CF 26mm (RoHS)
Resistor 33K 1/6W ±5% CF 26mm (RoHS)
Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)
Resistor 47K 1/6W ±5% CF 26mm (RoHS)
Resistor 470K 1/6W ±5% CF 26mm (RoHS)
Resistor 5.1K 1/6W ±5% CF 26mm (RoHS)
Resistor 5.6K 1/6W ±5% CF 26mm (RoHS)
metal filmResistor 4.53K 1/6W ±1% MF26mm (RoHS)
metal filmResistor 4.99K 1/6W ±1% MF26mm (RoHS)
horizon variable Resistor B20K (RoHS) CROSSOVER
horizon variable Resistor D16 50K/1 A (RoHS) LEVEL
2
2
1
1
1
4
1
1
1
4
1
1
3
1
1
1
1
1
R270
R213,R214,R215,R254,R253
R212,R216,R217,R220,R221,R222,R225,R226,R228,
R232,R235,R240
R231,R266
R259
R227
R262
R257
R238,R250,R255,R233
R251
R237
R249
R200,R207,R258,R260
R219
R252
R211,R229,R230
R224
R223
R234
VR202,
VR201,
metalize CAP. 0.22uF 63V ±5% MSC (RoHS)
metalize CAP. 0.56uF 63V ±5% (RoHS)
disc capacitor 220P 50V ±10% (RoHS)
disc capacitor 0.1U 50V +80/-20% (RoHS)
disc capacitor 22PF CH 50V±10% (RoHS)
disc capacitor22P 50V +/-10% (RoHS)
Mylar capacitor 0.01uF 50V ±5% (RoHS)
Mylar capacitor 0.1U 50V ±5% (RoHS)
electrolytic CAP. 1U 50V ±20% (RoHS)
electrolytic CAP. 10uF 50V ±20% (RoHS)
electrolytic CAP. 100uF 16V ±20% (RoHS)
electrolytic CAP. 2.2U 50V ±20% (RoHS)
electrolytic CAP. 22U 50V ±20% (RoHS)
metalize capacitor 0.47U 63V ±5% MSC (RoHS)
1
1
9
7
1
1
2
2
1
7
2
1
1
2
C218
C216
C207,C208,C210,C211,C212,C214,C220,C230,C249
C232,C242,C244,C245,C246,C252,C254
C229
C229
C223,C224
C215,C217
C228
C206,C213,C231,C241,C243,C251,C253
C233,C234
C219
C225
C221,C222,
transistor 2SC1815GR TOSHIBA (RoHS) NPN
diode 100mA 75V SIGNAL 1N4148ROHM (RoHS)
zener diode 5.1V 1/2W 52mm (RoHS)
IC OPA 4558 DUAL OP-AMP
I .C TL074cm st QUAD OP-AMP
double colors LED 204HGW 3¢(RoHS)
2
7
1
2
2
1
Q206,Q207
D201,D202,D207,D208,D211,D212,D214
D213
U101,U203,
U201,U202,
LED1
WIRE ASS'Y 2 PIN 250mm white/red(RoHS)
JACK RCA-326 (RoHS)
SWITCH SLIDE 6PIN MS7210V(RoHS) PHASE
JUMPER WIRE 26mm (RoHS)
1
1
1
30
TO LED1,
JK202,
SW301,
ALL J,D215,D216
Capacitors
129-a224j633-e
129-a564j633-e
130-2b221k503-e
130-3f104z503-e
130-ch220k503-e
130-2b220k503-e
132-103j503-e
132-104j503-e
135-3105m50-e
135-3106m50-e
135-3107m16-e
135-3225m50-e
135-3226m50-e
129-a474j633-e
Semiconductors
192-027c1815gr-e
197-031n4148-e
199-15000515-e
190-06m4558d-e
190-16tl074cn-e
195-10204hgw-e
Miscellaneous
162-50259201-e
174-0rca326p-e
180-tms7210v-e
13
PS series PS28 subwoofer
Part Number
Description
Qty Reference Designator
POWER/MAIN PCB
Resistors
110-14472j26-e
110-14681j26-e
110-16101j26-e
110-16102j26-e
110-16103j26-e
110-16105j26-e
110-16123j26-e
110-16152j26-e
110-16153j26-e
110-16154j26-e
110-16181j26-e
110-16182j26-e
110-16223j26-e
110-16332j26-e
110-16392j26-e
110-16393j26-e
110-16470j26-e
110-16471j26-e
110-16472j26-e
110-16473j26-e
110-16560j26-e
110-16563j26-e
110-16682j26-e
110-10821jk2-e
110-122r2j15-e
110-20331jk2-e
110-20331jk3-e
113-50r10j10-e
114-03302m0-e
Resistor 4.7K 1/4W ±5% CF 26mm (RoHS)
Resistor 680Ω 1/4W ±5% CF 26mm (RoHS)
Resistor 100Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 1K 1/6W ±5% CF 26mm (RoHS)
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
Resistor 1M 1/6W ±5% CF 26mm (RoHS)
Resistor 12K 1/6W ±5% CF 26mm (RoHS)
Resistor 1.5K 1/6W ±5% CF 26mm (RoHS)
Resistor 15K 1/6W ±5% CF 26mm (RoHS)
Resistor 150K 1/6W ±5% CF 26mm (RoHS)
Resistor 180Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 1.8K 1/6W ±5% CF 26mm (RoHS)
Resistor 22K 1/6W ±5% CF 26mm (RoHS)
Resistor 3.3K 1/6W ±5% CF 26mm (RoHS)
Resistor 3.9K 1/6W ±5% CF 26mm (RoHS)
Resistor 39K 1/6W ±5% CF 26mm (RoHS)
Resistor 47Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 470Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)
Resistor 47K 1/6W ±5% CF 26mm (RoHS)
Resistor 56Ω 1/6W ±5% CF 26mm (RoHS)
Resistor 56K 1/6W ±5% CF 26mm (RoHS)
Resistor 6.8K 1/6W ±5% CF 26mm(RoHS)
Resistor 820Ω 1W ±5% 10mm (RoHS)
Resistor 2.2Ω 1/2W ±5% 15mm (RoHS)
Resistor 330Ω 2W ±5% 5mm (RoHS)
Resistor 330Ω 2W ±5% (RoHS)
cement Resistor 0.1Ω 5W ±5% (RoHS)
semi-fixed Resistor 3K 0.3W ±20% (RoHS)
2
2
1
1
1
1
2
6
4
1
2
1
3
3
2
1
4
1
3
1
1
1
1
1
1
1
1
2
1
R147,R150
R148,R151
R120
R124
R134
R143
R135,R139
R103,R123,R136,R137,R141,R142
R118,R145,R152,R154
R131
R111,R114
R153
R128,R129,R133
R106,R107,R144
R105,R108
R126
R112,R113,R115,R116
R140
R110,R125,R130
R101
R117
R104
R109
R132,
R127,
R146,
R149,
R121,R122,
R138,
disc capacitor 1000P 50V ±10% (RoHS)
disc capacitor 0.1U 50V +80/-20% (RoHS)
disc capacitor 0.047U 50V ±20% (RoHS)
Mylar capacitor 0.1U 50V ±5% (RoHS)
Mylar capacitor 0.022uF 100V ±5% (RoHS)
electrolytic CAP. 1U 50V ±20% (RoHS)
electrolytic CAP. 100uF 16V ±20% (RoHS)
electrolytic CAP. 22U 50V ±20% (RoHS)
electrolytic CAP. 220U 10V ±20% (RoHS)
electrolytic CAP. 220U 16V ±20% (RoHS)
electrolytic CAP. 47U 25V ±20% (RoHS)
mylar capacitor 0.022uF 100V ±5% (RoHS)
electrolytic CAP. 100uF 16V ±20% (RoHS)
electrolytic CAP. 6800U/50V ±20% D25X45mm (RoHS)
1
4
1
1
4
2
3
2
2
1
1
2
1
2
C116
C108,C113,C115,C119
C106
C107
C124,C125,C126,C128
C105,C112
C109,C117,C120
C114,C118
C129,C130
C111
C103
C123,C127,
C110,
C121,C122,
transistor 2SC1815GR TOSHIBA(RoHS)
transistor FSC 2N5551 (RoHS) NPN
transistor FSC 2N5401 AI-PNP 350V500mA TO-92 (RoHS)
diode 100mA 75V SIGNAL 1N4148ROHM (RoHS)
zener diode 3.3V 1/2W 52mm (RoHS)
zener diode HZ6C2 RENESAS (RoHS)
zener diode HZ16-2 RENESAS (RoHS)
IC OPA 4558 DUAL OP-AMP
transistor TIP35C (RoHS) NPN
transistor TIP36C (RoHS) PNP
7
2
2
6
1
2
1
2
1
1
Q102,Q111,Q112,Q113,Q118,Q114,Q116
Q103,Q109
Q104,Q110
D101,D103,D105,D108,D117,D118
D102
D106,D107
D109
U101,U203,
Q107,
Q108,
Capacitors
130-2b102k503-e
130-3f104z503-e
130-3f473m503-e
132-104j503-e
132-223ja03-e
135-3105m50-e
135-3107m16-e
135-3226m50-e
135-3227m10-e
135-3227m16-e
135-3476m25-e
132-223ja03-e
135-3107m16-e
135-4688m50-e
Semiconductors
192-027c1815gr-e
192-1572n5551-e
192-1582n5401-e
197-031n4148-e
199-15000335-e
199-15000625-e
199-15001605-e
190-06m4558d-e
192-021tip35c-e
192-022tip36c-e
14
PS series PS28 subwoofer
Part Number
Description
Qty Reference Designator
POWER/MAIN PCB
192-027c1815gr-e
192-201d882y-e
192-202b772y-e
192-991d669a-e
192-992b649t-e
197-00kbl405-e
197-031n4148-e
197-101n4002-e
transistor 2SC1815GR TOSHIBA(RoHS) NPN
transistor KSD882Y (RoHS) PNP
transistor KSB772Y (RoHS) PNP
transistor HI-SINCERITY HSD669A (RoHS) NPN
transistor HSB649T (RoHS) PNP
diode 4A 500V KBL405 (RoHS)
diode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)
diode 1N4002TB (RoHS)
2
1
1
1
1
1
1
1
Q101,Q115,
Q117,
Q119,
Q106,
Q105,
D110,
D116,
D104,
1
1
1
RY101,
P101,
P102,
1
P103,
2
1
1
4
1
2
1
for Q107,Q108,
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
metal filmResistor 11.3K 1/6W ±1% MF 26mm (RoHS)
Resistor 10K 1/6W ±5% CF 26mm (RoHS)
Resistor 18K 1/6W ±5% CF 26mm (RoHS)
Resistor 22K 1/6W ±5% CF 26mm (RoHS)
Resistor 27K 1/6W ±5% CF 26mm(RoHS)
Resistor 33K 1/6W ±5% CF 26mm(RoHS)
Resistor 4.7K 1/6W ±5% CF 26mm (RoHS)
Resistor 470K 1/6W ±5% CF 26mm (RoHS)
Resistor 750Ω 1/6W ±5% CF 26mm(RoHS)
1
1
8
1
2
1
1
2
1
2
back
back
R301,R303,R304,R308,R309,R314,R340,R344
R302
R310,R312
R341
R305
R342,R343
R307
R311,R313
disc capacitor 0.1U 50V +80/-20% (RoHS)
mylar capacitor 0.01uF 50V ±5% (RoHS)
electrolytic CAP. 22U 50V ±20% (RoHS)
electrolytic CAP. 47U 25V ±20% (RoHS)
2
2
2
1
C305,C306
C302,C303
C301,C340
C304
I .C TL074cm st QUAD OP-AMP
diode 100mA 75V SIGNAL 1N4148 ROHM (RoHS)
transistor 2SC1815GR TOSHIBA (RoHS) NPN
diode 100mA 75V SIGNAL 1N4148ROHM (RoHS)
1
1
2
2
U301,
back
Q301,Q302
D301,D302
CABLE ASS'Y 280mm AWG26 WHT (RoHS)
90mm 28AWG (RoHS)
wire connector & base 40PIN PITCH=2.54mm HR2*40
(RoHS)
1
1
to SW301,
Miscellaneous
171-udhss124d-e
175-1c07v01-e
175-1d02v01-e
relay 5A 24V UDH-SS124D (RoHS)
wire connector & base 7PIN PITCH=2.5mm (RoHS)
wire connector & base 2PIN PITCH=3.96mm (RoHS)
wire connector & base 3 PIN PITCH=3.96mm JST-VH cut
175-1d03v01-e
off the middle PIN (RoHS)
193-3m2520-e
insulator TO-3P 25x20mm (RoHS)
323-AL-00020-0LAE HEAT SINK 65*32*31 AL
351-AM03014A094-E M3*14 machine screw black (RoHS)
352-AM03008D040-E ¢3*8 B type ping screw black (RoHS)
361-FE-00051-0LAE transistor holder 14.2*8.0*5.2t=1.6mm (RoHS)
361-NYL-00054-0LAE transistor insulator pad (SW06002) (RoHS)
362-FE-00041-0LAE PCB support 11.75*8.5*12.5H(RoHS)
LIMITER PCB
Resistors
110-16103j26-e
116-161132f26-e
110-16103j26-e
110-16183j26-e
110-16223j26-e
110-16273j26-e
110-16333j26-e
110-16472j26-e
110-16474j26-e
110-16751j26-e
Capacitors
130-3f104z503-e
132-103j503-e
135-3226m50-e
135-3476m25-e
Semiconductors
190-16tl074cn-e
197-031n4148-e
192-027c1815gr-e
197-031n4148-e
Miscellaneous
162-50289001-e
162-80098201-e
175-9f40hr2-e
15
P301,
PS series PS28 subwoofer
Part Number
Description
Qty Reference Designator
MISCELLANEOUS/MECHANICAL
123-14j70d-e
130-3f472md00-e
150-e8604107-e
1
1
1
154-u25006t0-e
155-520020-e
162-10151001-e
162-50652003-e
176-wjce1-e
180-prf1003s-e
302-AL-00406-1BDE
306-ABS-00177-0BAE
311-ABS-00028-0BAE
320-RUB-00033-0BAE
323-AL-00106-0BBE
333-EVA-00761-0BAE
333-EVA-00783-0BAE
333-EVA-00807-0BAE
333-EVA-00826-0BAE
333-EVA-00835-0BAE
335-NYL-05015-0BAE
337-CU-00101-0LAE
350-EM04012D024-E
351-AM03008A079-E
351-HM04016A218-E
352-AM03008D040-E
352-AM03010D065-E
354-GM04002-E
Ferrite Core U-16.3*8.2*13 (J70)+CASE (RoHS)
disc capacitor 4700P 400V ± 20% safy long foot (RoHS)
transformer EI-86 60Hz 120V TT0869906580
power line cord polar SVT FT-2 6FT double insulation
(RoHS)
fuse 2.5A 250V 20mm (RoHS)
fuse holder R3-11 (RoHS)
WIRE UL1617 150mm 22AWG BROWN 6:6 (RoHS)
WIRE 650mm RED=205# 0.5T BLK=110# 0.5T (RoHS)
wire connector pin CE-1 (RoHS)
power switch ROCK RF-1003-BB2-OHA (RoHS)
rear board 300*200*2.5T black (RoHS)
rear housing 198*298*102mm (RoHS)
knob CROSSOVER,LEVEL 46077-W P.V.C. (RoHS)
rubber foot pad 25*21*4t (RoHS)
HEAT SINK 117.5*71.5*25 black (RoHS)
Gasket 18*9*2T (RoHS)
Gasket W 198*12*2.0T
Gasket L 274*12*2.0T (RoHS)
Gasket W 198*12*1.0T (RoHS)
Gasket L 274*12*1.0T (RoHS)
wire clip SB4F-2 black (RoHS)
metal foil 65L*50W (RoHS)
4¢*12 wood screw black (RoHS)
M3*8 machine screw black (RoHS)
M4*16 machine screw black(RoHS)
¢3*8 B type ping screw black (RoHS)
¢3*10 P type ping screw black(RoHS)
M4 screw cap adding pad black(RoHS)
362-FE-00013-0LAE
PCB support L TYPE t=1.6mm S.P.C.C 89*9*1.6T (RoHS)
2
152-u602015-e
16
T1
1
1
1
1
1
1
1
1
1
2
4
1
1
2
2
2
2
2
1
4
7
4
8
2
4
FS101,
SW100
PS series PS28 subwoofer
17
PS series PS28 subwoofer
18
PS series PS28 subwoofer
19
PS series PS28 subwoofer
20
PS series PS28 subwoofer
21
PS series PS28 subwoofer
22
PS series PS28 subwoofer
23
PS series PS28 subwoofer
24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement