Infocus AA0021 User manual

Infocus AA0021 User manual
010-0752-02
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 13190 SW 68th Parkway, Suite 200, Portland, Oregon
97223-8368 USA
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void authority
to operate the equipment.
We declare under our sole responsibility that this projector conforms to the following
directives and norms:
ErP Directive 2009/125/EC
EMC Directive 2004/108/EC
Low Voltage Directive 2006/95/EC
R&TTE Directive: 1999/5/EC
EMC: EN 55022, EN 55024, EN 61000-3-2, EN 61000-3-3
Safety: IEC 60950-1: 2005 (MOD)
ETSI: EN 300 440, EN 301 489
The receiver portion of this product is a Category III device, as specified in EN 300 440.
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks
of Microsoft Corporation. Adobe and Acrobat are trademarks or registered trademarks of
Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo are registered trademarks
of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments. InFocus, In
Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus
Corporation in the United States and other countries.
Canada
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numérique de
la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
cTUVus
Other specific Country Approvals may apply. Please see product certification label.
NOTE: This product is covered electrical and electronic equipment under the
This document applies to regulatory model AA0021.
European Union's Waste from Electrical and Electronic Equipment ("WEEE")
Directive (2002/96/EC). The WEEE Directive requires that covered
equipment be collected and managed separately from typical household waste
in all EU member states. Please follow the guidance of your local
environmental authority or ask the shop where you purchased the product for
collection or recycling options.
Input ratings: 100-240Vac, 3.9A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time without
notice.
1
Table of Contents
Introduction
Positioning the projector
Connecting a computer source
USB connection
VGA connection
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
VGA connection
Component video connection
LiteBoard™ Wand
Charging the Wand’s Battery
How to Use the Wand
Wand Position and Avoiding Shadows
Using More than One Wand
Wand Features
Buttons and Wand Tip
LiteBoard Wand Menu
Troubleshooting LiteBoard
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Dynamic Messaging
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Using LitePort
LiteShow
LiteShow Menu Options
Maintenance
Cleaning the lens
Using the security lock
Replacing the projection lamp
4
6
7
7
7
7
8
9
11
11
11
11
11
12
12
12
12
13
13
13
14
14
16
16
24
25
27
28
28
29
29
29
30
31
32
2
33
36
37
39
40
46
46
46
47
Important Operating Considerations for Safety
•
Refer all service to qualified service personnel. Servicing your own projector
can be dangerous to you and will void the warranty.
•
Only use replacement parts specified by InFocus. Unauthorized substitutions
may result in fire, electrical shock, or injury, and may void the warranty
•
Only genuine InFocus lamps are tested for use in this projector. Use of non
InFocus lamps may cause electrical shock and fire, and may void the projector
warranty.
•
Refer to this guide for proper startup and shutdown procedures.
•
Follow all warnings and cautions in this manual and on the projector.
•
Place the projector in a horizontal position no greater than 15 degrees off axis.
•
Locate the projector at least 4' (1.2m) away from any heating or cooling vents.
•
Do not block ventilation openings. Locate the projector in a well-ventilated
area without obstructions to intake or exhaust vents. Do not place the projector
on a tablecloth or other soft covering that may block the vents.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
•
Do not place the projector in direct sunlight, humid, greasy or dusty places or
in places where the projector may come into contact with smoke or steam.
•
•
•
Do not touch or block the projector lens with any objects as this can damage
the projector lens. Use the lens cap when the projector is not in use and during
transport. Scratches, gouges and other lens damage are not covered by the
product warranty.
Do not look directly into the lens while the projector is being used.
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
•
•
Do not drop the projector.
In the unlikely event of a lamp rupture, particles may exit through the projector
vents. Keep people, food, and drinks out of the "keep out" area under and
around the projector, as indicated by the "X" areas below.
•
Do not spill liquid on the projector. Spilled liquid may damage the projector.
•
Use the power cord provided. Connect the power cord to a receptacle with a
protective safety (earth) ground terminal. A surge-protected power strip is
recommended.
•
Do not overload wall outlets.
•
When disconnecting the power cord, hold the plug, not the cord.
•
Wash hands after handling the cables supplied with this product.
•
The projector remote control uses batteries. Make sure the batteries’ polarity
(+/-) is aligned correctly. Dispose of used batteries in accordance with local
disposal laws.
•
Use an InFocus approved ceiling mount kit for proper fitting, ventilation and
installation. The warranty does not cover any damage caused by use of nonapproved ceiling mount kits or by installing in an improper location.
•
When the projector is ceiling mounted, wear protective eyewear to prevent eye
injury before opening lamp door.
2’
/0
.6
8’ / 2
.4 m
/
5’
m
3’ / 1
m
m
1.5
Follow these instructions to help ensure image quality and lamp life over the life of
the projector. Failure to follow these instructions may affect the warranty. For
complete details of the warranty, see the Warranty Booklet.
3
Introduction
Your new digital projector is simple to connect, easy to use, and straightforward to
maintain. It is a versatile projector that is flexible enough for business presentations
and home video viewing too. The IN3916 has native XGA 1024x768 resolution. It
is compatible with a wide variety of computers and video devices.
touch keypad
focus (front ring)
Product specifications
To read the latest specifications on your multimedia projector, be sure to visit our
website at www.infocus.com, as specifications are subject to change.
Accessories
The standard accessories that came with your projector are listed in the included
Quick Start Poster/Booklet. Optional accessories can be found on our website at
www.infocus.com or at your retailer or dealer.
lens
remote control
receiver (IR)
elevator foot
Online registration
Register your projector on our website at www.infocus.com/register to activate
your warranty and receive product updates, announcements, and registration
incentives.
remote control
receiver (IR)
4
power cord
connector
connector
panel
Connector panel
The projector provides both computer and video connection options, including:
•
•
•
•
•
•
•
•
•
•
•
•
•
VGA computer
Composite video
HDMI
USB mini B connector. Used for USB Display, slide advance (and mouse
control when used with an optional remote control only) and LiteBoard™
Wand control.
USB A connector. Used for LitePort (JPEG images displayed from USB flash
drive) and WLAN.
Monitor out, for VGA pass through to an external monitor.
Audio input for video and computer.
Audio L/R for video and computer.
Audio output to external speakers.
Microphone, for connecting to a dynamic microphone.
LAN (RJ45) connector for network control and web server.
Serial Control (DB9) connector for RS-232 serial control. Command control
codes are on our support website at www.infocus.com/support.
5 volt DC output. The coaxial connector accepts a 2.1mm x 5.5mm plug and
provides a constant 5 volt, 2 amp DC output when the projector is on. It is
designed to provide power for an InFocus LiteShow wireless device, which
allows wireless projection. More information can be found on our website at
www.infocus.com or at your retailer or dealer.
RJ45 port
audio L/R
HDMI
computer
USB A
audio in/out
USB mini
USB A
USB mini B
5 volt output
security lock
monitor
out
serial control
5
composite
video
microphone
Positioning the projector
Table 1: Screen Size
To determine where to position the projector, consider the size and shape of your
screen, the location of your power outlets, and the distance between the projector
and the rest of your equipment. Here are some general guidelines:
•
•
•
•
Diagonal Screen
Size
Position the projector between 30 inches (.75m) and 65 inches (1.65m) from
the screen. To ensure adequate cable access, do not place the projector within
24 inches (.61m) of a wall or other object.
If you are installing the projector on the ceiling, we strongly recommend using
InFocus approved ceiling mounts for proper fitting, ventilation and
installation. Refer to the installation guide that comes with the InFocus Ceiling
Mount Kit (p/n SP-CEIL-UNIV) for more information. The warranty does not
cover any damage caused by use of non-approved ceiling mount kits or by
installing in an improper location. To turn the image upside down, see “Ceiling
mount” on page 34. We recommend using an InFocus authorized ceiling
mount.
Position the projector the desired distance from the screen. The distance from
the lens of the projector to the screen and the video format determine the size
of the projected image. (The throw ratio of the IN3916 is 0.49:1.)
IN3916 image offset is 105% +/-2%. This means that if you have an image 40
inches (1 meter) tall from a table-mounted projector, the bottom of the image
will be 2.8 inches (.07 meter) above the centerline of the lens.
40 inches
high image
bottom of image 2.8
inches above center
of lens
Projection angle
lens center
6
Size of the Projected Image
Width
Feet
Inches
Meters
Inches
5.9
6.7
7.5
7.8
8.3
8.7
10.0
13.0
71
80
90
94
100
104
120
156
1.8
2.0
2.3
2.4
2.5
2.6
3.0
4.0
60
68
76
80
85
88
102
133
Milimet
ers
153
172
194
202
215
224
258
337
Projection
Distance (L)
Minimum
Meters
Inches
0.75
0.84
0.95
0.99
1.05
1.10
1.26
1.65
30
33
37
39
41
43
50
65
Connecting a computer source
To take advantage of HDMI 1.3 Deep Color (30 bit), you must have a 1.3compatible source.
USB Mini B connection
Connecting power
Connect the USB cable to your computer's USB A connector and to the projector's
USB mini B connector.
Connect the black power cord to the Power connector on the rear of the projector
and to your electrical outlet. The Power light on the Status Indicator Panel (page 16)
turns amber. NOTE: Always use the power cord that shipped with the projector.
To display images over USB: If this is the first time you have used the USB
Display feature, an Auto-Play screen will appear within a minute. Click Start USB
Display. (Note: If the Auto-Play screen does not appear, browse to the CD Drive
USB Display on your computer and double-click the DLUSB.Cab file to initiate
manually.)
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio 1 connector on the projector. You may
also need an adapter.
Within a minute, your computer image should display.
To display a presentation using a USB flash drive, see the Using LitePort (page 37).
This feature displays JPEG images and Presentation-to-Go presentation,
eliminating the need for a computer source.
To stop displaying your computer image over the USB cable: Disconnect the
USB cable from the projector and/or laptop or change the selected source on the
projector.
If you are using a desktop computer and want to see the image on your computer
screen as well as on the projection screen, connect the computer’s monitor cable to
the Monitor Out connector on the projector.
To advance slides in a PowerPoint presentation using the remote control: Press
the up and down arrow buttons on the remote control to move through your slides.
VGA connection
connect USB cable
Connect one end of the provided computer cable to the VGA 1/VGA 2 connector
on the projector and the other to the VGA connector on your computer. If you are
using a desktop computer, you will need to disconnect the monitor cable from the
computer’s video port first.
USB A
USB mini B
MOLEX
MOLEX
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
connect VGA cable
7
USB A
USB mini B
Displaying an image
press Power button
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp comes on,
the start up screen displays and the Power button is steady green. It can take up to a
minute for the image to achieve full brightness.
? No start up screen? Get help on page 17.
Turn on your computer or video device.
turn on computer or
video device
The image should appear on the projection screen. If it doesn’t, press the Source
button on the projector’s keypad or remote.
If you are using a VGA cable to connect your computer to the projector:
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/LCD key
turns the external display on and off. Locate a function key labeled CRT/LCD or a
function key with a monitor symbol. Press FN and the labeled function key
simultaneously.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
Refer to your laptop's documentation for more information about your
laptop's key combination or go to the InFocus website at: http://
www.infocus.com/Support/LaptopActivation.aspx.
? No laptop image? Try pressing the Auto Image button on the keypad. Get
help on page 17.
8
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot release
button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
elevator
foot
Avoid placing your hands near the hot exhaust vent at the front of the projector.
adjust distance
Position the projector the desired distance from the screen at a 90 degree angle to
the screen.
See page 6 for a table listing screen sizes and distances.
Adjust the focus.
adjust focus
If the image is not square, first make sure that the projector is perpendicular to the
screen. If the image is larger or smaller on the top or bottom edge of the screen,
press the top Keystone button to reduce the upper part of the image, and press the
bottom Keystone button to reduce the lower part.
focus
If the left or right side of the screen is larger or smaller the other, you can turn the
projector to the left or to the right a few degrees to square the image.
adjust keystone
Adjust the Contrast or Brightness in the Basic Picture menu. See page 31 for help
with these menu adjustments.
For Aspect Ratio, keep in mind that DVD players must be configured for 16:9 in
order to view the highest quality image. For more information regarding Aspect
Ratio, see page 10.
adjust Basic Picture
Basic Picture
i
9
Brightness
Contrast
Sharpness
Color
Tint
Auto Image...
Aspect Ratio
Apply Preset...
50
50
Maximum
50
50
Auto
What is Aspect Ratio?
4:3 screen
Aspect ratio is the ratio of the image width to image height. Depending on your
source, you will want to choose the aspect ratio (using your projector remote or
keypad) which matches your source.
Older TV screens and laptops are 4:3; newer TV screens, HDTV and most DVDs
are 16:9; and widescreen computers are 16:10.
16:10 screen
4:3
mode
Use an aspect ratio of 16:9 for widescreen movies and HDTV, and use Native for
4:3 content. Force Wide can also be enabled to automatically resize less common
aspect ratios to 16:10.
16:10
mode
Native
mode
10
Composite video connection
Connecting a video device
Plug the composite video cable’s yellow connector into the video-out connector on
the video device. Plug the other yellow connector into the yellow Video connector
on the projector.
You can connect video devices such as VCRs, DVD players, camcorders, digital
cameras, video game consoles, HDTV receivers, and TV tuners to the projector.
You can connect the audio directly to the projector to get sound from the built-in
speaker, or you can bypass the projector’s audio system and connect the audio
directly from your source to a stereo or home theater system.
If your source uses RCA connectors, connect the red audio-out connector on the
audio source to the red audio-in connector on the projector and white audio-out
connector on the audio source to the white audio-in connector on the projector.
You can connect the projector to most video devices that can output video. You
cannot directly connect the coaxial cable that enters your house from a cable or
satellite company, the signal must pass through a tuner first. Examples of tuners are
digital cable boxes, VCRs, digital video recorders, and satellite TV boxes.
Basically, any device that can change channels is considered a tuner.
If your source uses a 3.5mm stereo connector, connect it to the 3.5mm audio-in
connector on the projector.
VGA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This connector may
be labeled “To Monitor” on the video source. Plug the computer cable into the VGA
connector on the projector.
Before connecting your projector, you should decide which aspect ratio you want to
use. The projector’s Aspect Ratio setting is accessed through the Resize button on
the remote or through the projector’s Basic Picture Menu. See page 31 for more
information.
Component video connection
Video device connections
If your HD video device has component connectors, an optional Component to
VGA adapter can be used. Plug the component cable into the video device. Plug the
other end of the component cable into the adapter and plug the adapter into the
VGA connector.
No video cables are provided with the projector. You can order cables from InFocus
or provide your own.
HDMI 1.3 connection
HDMI is a standard, uncompressed, all-digital audio/video interface. HDMI
provides an interface between sources, such as set-top boxes, DVD players, and
receivers and your projector. Plug an HDMI cable into the video-out connector on
the video device and into the HDMI connector on the projector.
To take advantage of HDMI 1.3 Deep Color (30 bit), you must have a 1.3compatible source.
11
LiteBoard™ Wand
the source to VGA 1 or VGA 2 (press the source button on the projector or its
remote if needed - you may need to press it several times).
The LiteBoard Wand works like a wireless mouse - but one that works in midair, not
on your desktop. Just hold the wand in your hand, and point it at the projected
image to point, click and drag. The wand works with all your software, just like a
regular mouse.
6 Turn on the wand by pressing its tip, left or right button - the wand's blue status
light will start to blink.
7 Point the wand at the screen to point, click, and drag - just like a normal mouse.
The Undo button is located at the bottom of the wand. You can define this
button in the LiteBoard Wand Menu.
Charging the Wand’s Battery
When the wand’s amber battery light starts to blink, its internal battery is low (if the
battery is fully discharged, you won’t be able to turn the wand on by pressing its tip,
left or right buttons).
To charge the battery, open the flap at the bottom of the wand to expose the wand’s
USB connector. Then connect a USB cable between the wand and the USB power
adapter, or a computer (if connecting to a computer, make sure the computer is
powered on). The battery light will stay on while the battery is charging, then it will
turn off when the battery is fully charged.
When charging is finished, you can disconnect the USB cable (or keep the cable
connected and use the wand while it’s charging).
NOTE: 5-10 minutes of charging is enough for about an hour of wand use. A full
charge will take 6-8 hours and will allow 20-40 hours of non-stop wand use. A fully
charged, new wand will hold a charge in standby for up to 3 weeks.
Caution: The lithium battery is only rechargeable, and is not user serviceable or
user replaceable.
Caution: Always use the included USB cable and power adapter (or your
computer) to charge the wand.
NOTE: See LiteBoard Wand Menu below for settings that let you fine-tune wand
motion and clicking behavior. When you’re done, set the wand aside and make sure
it isn’t pointing at the screen; it will turn itself off automatically after 1 minute.
Wand Position and Avoiding Shadows
Your Location Distance from the Screen
You can use the LiteBoard Wand right up against the screen, or around the room.
You might find that your pointing accuracy will improve if you get closer to the
screen. Also, avoid standing too far off from either side of the screen.
Avoid Shadows!
The wand won't work if its sensor is in a shadow or if it is pointing at a shadow:
Correct (no shadow)
How to Use the Wand
1 The IN3916 projector needs to be powered on and connected to your computer.
2 Connect the projector and your computer with a USB cable.
3 Connect the projector and your computer with a VGA cable.
4 Make sure the wand's battery is charged or charging.
5 Turn on the projector and make sure it's displaying the computer's screen - set
12
Incorrect (shadow)
Wand Features
How to Hold the Wand
You can hold the wand the way you would hold a normal pencil or pen, or you can
hold it like a remote control - use in whichever position is most comfortable.
NOTE: If the wand is up close to the screen, you can press its tip against the
projection surface to click and drag. Not recommended for use with fabric screens.
Sensor
Tip
Left mouse button
Scroll Wheel button
Using More than One Wand
Link light
The projector can work with more than one wand, but you can only use one wand at
a time. When you want to switch to a different wand:
Right mouse button
Battery light
1 Point the current wand away from the projected image for at least 3 seconds.
2 Press the tip, left or right button on the new wand to turn it on, and then start
Undo button
using the new wand.
USB connector
NOTE: Settings in the projector's LiteBoard Wand menu (see below) apply to all
wands used with that projector.
Reset button
Buttons and Wand Tip
The wand's three top buttons are equivalent to the left, right, and scroll wheel
buttons on a mouse. The wand's tip is also a button, and is equivalent to the left
mouse button.
NOTE: By default, the Scroll Wheel button changes wand motion between Auto,
Normal and Draw. Auto switches between Draw, Normal and Stable mode
depending on the image size and distance. Normal makes clicking easier, but Draw
allows smoother motion. You can change the Scroll Wheel button to perform other
functions, including a standard middle button mouse click (see LiteBoard Wand
Menu below).
Battery Light
The amber battery light shows the status of the wand's built-in battery (see below
for battery information). The battery light will turn on while the wand is charging,
and it will blink if the battery is low (2-4 hours of wand use left).
13
Link Light
Lithium Battery Information
The blue link light shows the status of the wand's wireless connection to the
projector. The link light will blink frequently (more than once per second) when the
wand is attempting to link to the projector; then it will blink less frequently (about
once every 4 seconds) after the wand has linked to the projector.
NOTE: The link light will stay off when the wand is off.
Manufacturer: HiTech Energy Inc.
Model: E3BE105K1002
Rating: 3.7V/800mAh
Caution: Lithium battery is only rechargeable, and not user replaceable. Not user
serviceable.
USB Connector
LiteBoard Wand Menu
The wand's USB connector is behind a flap on the back of the wand. The USB
connector is only used for charging the wand's battery - using the included USB
power adapter, or a computer.
NOTE: You can use the wand while charging the battery, but after the battery is
charged (battery light turns off), you can unplug the USB cable and continue to use
the wand without a cable.
You can access the LiteBoard Wand menu from the projector's Setup menu. To
change the settings in this menu, highlight a setting, then press Select (on the
projector or its remote) one or more times - each press of Select will change to the
next value for the setting.
Enabled: controls whether the projector lets you use LiteBoard Wands. Set this to
Yes to allow wand use. Set this to No to prevent wand use.
Undo Button
The wand's Undo button will function the same as the computer's Escape, Delete, or
Backspace buttons, or the same as a Ctrl+Z (Windows/Linux) or Cmd+Z (Mac OS)
command, depending on which function you assign to it in the LiteBoard Wand
menu.
Motion: controls wand motion. When set to Auto, the motion mode will switch
between Normal, Draw and Stable depending on the image size and distance.
When set to Normal, motion is set up to work best for normal computer use. When
set to Draw, motion is set up to work best for on-screen drawing. When set to
Stable, motion is filtered for maximum stability. When set to Press to Move, the
mouse pointer only moves when you hold down the wand’s tip or the left button on
the wand (use the right button to click).
Sensor
The wand's optical sensor opening is located above the wand's tip. Don't block the
sensor, and make sure it always has a clear view of the screen.
NOTE: The sensor won't work if you point it at a shadow or away from the screen.
Click Speed: controls the motion pause when you click and only applies if Motion
is set to Normal or Stable. Longer click speeds will make it easier to double-click,
but will increase the delay before motion resumes after you click.
Reset Button
The wand has a reset button, behind a small hole on its underside. Under normal
conditions, you should not need to reset the wand. See the Troubleshooting section
below for more information.
Scroll Button Mode: selects the function of the wand's Scroll Wheel button. You
can use the Scroll Wheel button to change wand motion, or perform keyboard or
mouse button shortcuts.
NOTE: The PwrPnt Annotate setting sets up the Scroll Wheel button to control
drawing (annotating) during Microsoft PowerPoint slide shows. The first press of
the Scroll Wheel button will turn on the drawing function, the next press will turn
off the drawing function, the next press will turn it on again, etc.
Internal Radio
The wand has a built-in wireless transmitter/receiver which it uses to communicate
with the projector.
Undo Button: selects the function of the wand's undo Button.
Link Channel: selects the radio channel used for wand communication. This
should be set to Auto unless you encounter interference (see Troubleshooting below
for more information).
14
Troubleshooting LiteBoard
•
For the most up-to-date information, visit our support site at www.infocus.com/
support
•
If the wand doesn't work at all, or it works intermittently, try one of these
solutions:
- Press to Move may be enabled; try holding down one of the wand’s buttons
while moving the wand.
- Make sure the projector is displaying the same image as the computer's main
or built-in monitor (don't extend your desktop onto multiple monitors). To correct this:
- Press the tip, left or right button on the wand to turn it on.
On Windows XP: Open the Display control panel, click Settings, click the display that represents the projector, then un-check “Extend my Windows desktop...”.
- If the wand's blue Link light never blinks, then the wand's battery is fully discharged; connect the wand to the USB power adapter or your computer.
- Make sure the wand is not pointing at a shadow and make sure its tip is not in
a shadow.
On Windows Vista: Right-click on the desktop, choose Personalize..., click
Display Settings, click the display that represents the projector, then un-check
“Extend the desktop...”
- If the room is brightly lit, reduce the room illumination.
On Windows 7.0: Right-click on the desktop, choose Screen Resolution, click
the display that represents the projector, and then choose the “Duplicate Display...” under Multiple Displays.
- If you're trying to use the computer's mouse at the same time as the wand,
point the wand away from the screen while using the mouse.
- If someone else is using a different wand with the same projector, they must
stop using it before you can use another wand.
On Macintosh: Select System Preferences from the Apple Menu, then select
Displays. Click Arrangement, and check “Mirror Displays.”
- Change the Link Channel value in the LiteBoard Wand menu.
•
- Reset the wand: push the end of a paper clip into the reset opening on the
underside of the wand.
•
If accurate clicking is difficult, try one of these solutions:
- Hold the wand steadier when clicking.
If the battery light does not turn on when the wand is being charged, try one of
the following:
- Make sure a USB cable is connected between the wand and either the USB
power adapter, or a USB port on your computer.
- If the wand is connected to the USB power adapter, make sure the adapter is
plugged in to a live electrical outlet. If the wand is connected to your computer,
make sure the computer is powered on.
- Use the wand right up against the screen so it's easier to avoid unexpected
movements.
- If the wand still won't charge, contact InFocus support at: www.infocus.com/
support.
- Change the Motion value in the LiteBoard Wand menu.
•
If the mouse pointer is in the wrong place on the screen, or the mouse pointer's
movement is restricted to only part of the screen, try one of these solutions:
- Make sure your projector is displaying the computer's screen and not some
other source (such as DVD, VCR, etc.). To change the source, press the Source
button on the projector or its remote.
If it is difficult to draw or move freely because the wand wants to move in
straight lines or draw extra lines, try changing the Motion value in the
LiteBoard Wand menu.
15
Shutting down the projector
The Status Indicator Panel on top of the projector indicates the state of the projector
and can help you troubleshoot.
Screen Save Time
You can make the black screen appear after a preset number of minutes by turning
on the Screen Save Time feature in the Setup menu. See page 33.
Table 2: Status indicator light behavior and meaning
Auto Off Time
Icon
Meaning
Power, solid amber
The projector is plugged in.
Power, blinking green
The power button has been pressed and the
software is initializing.
To turn the projector off, press the Power button on the remote or keypad. The lamp
turns off and the LED blinks amber for 1 minute while the fans continue to run to
cool the lamp. When the lamp has cooled, the LED lights amber and the fans stop.
Unplug the power cable to completely power off the projector.
Power, solid green
The projector is on and initialized.
Power, blinking amber
The power button has been pressed to turn
the projector off and the fans are running
to cool the projector.
Troubleshooting your setup
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 22). Turn
off the projector and wait one minute, then
turn the projector on again. Contact
Technical Support if the problem persists.
Visit www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one minute,
then turn the projector on again. If the
lamp light turns on again, replace the lamp
and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one minute,
then turn the projector on again. If the
service lamp turns on again, service is
required. Visit www.infocus.com/support
to contact service.
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction with the
projector is performed for 30 minutes. By default, this feature is off. You can
change the length of time, see page 33.
Turning off the projector
If your image appears correctly on the screen, skip to the next section. If it does not,
troubleshoot the setup.
16
Problem
Solution
Result
No start up screen
Plug power cord into the projector
press power button
Correct image
USB A
USB mini B
Only start up screen appears
Press the Source button
activate laptop’s external port
Startup
Screen
Computer image projected
Startup
Screen
A
A
A
Restart laptop
17
Problem
No computer image, just the words “Signal out of
range”
Solution
Result
Press the Auto Image button on keypad
Adjust computer refresh rate in Control Panel >
Display > Settings > Advanced > Adapter (location
varies by operating system)
Computer image projected
A
Signal out of
the range
A
A
You may also need to set a different resolution on
your computer, as shown in the following problem,
“image fuzzy or cropped”
Only my laptop’s background appears, not the
Desktop icons
Disable “Extend my Windows Desktop” in Control
Panel > Display > Settings > Display 2 (location varies
by operating system)
Background and Desktop projected
A
A
A
A
Uncheck this
option, then
click Apply
18
Problem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
A
For a laptop,
disable laptop
monitor or turnon dual-display
mode
Image not centered on screen
Correct image
Move projector, adjust height
Advanced Picture
Adjust horizontal
or vertical position
in Advanced
Picture menu
i
19
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset
Horz Position
Vert Position
50
50
50
50
50
50
50
50
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
Basic Picture
Brightness
Contrast
Sharpness
Color
Tint
Auto Image...
i
Image does not fit 4:3 or 16:9 screen
50
Maximum
50
High
Normal
Low
Minimum
Maximum
50
50
Aspect Ratio
Apply Preset...
16:9
Change aspect ratio to 4:3 or 16:9 in Basic
Picture>Aspect Ratio menu
Basic Picture
i
Brightness
Contrast
Sharpness
Color
Tint
Auto Image...
Aspect Ratio
Apply Preset...
50
50
Maximum
50
50
16:9
20
Auto
Native
4:3
16:9
16:10
Letterbox
Panorama
Correct image
Problem
Solution
Image upside down
A
Result
Turn off Ceiling Mount in Setup menu
Correct image
Setup
Auto Source
On
Power-Up Source
Composite SCART
VGA1
RGB
Auto
Video Standard
Closed Caption
Ceiling Mount
i
Off
Rear Project
Off
Off
Prevent PC Screen Saver
On
Turn off Rear Project in Setup menu
Image reversed left to right
Correct image
Setup
A
Projected colors don’t match source
Auto Source
Power-Up Source
On
VGA1
Composite SCART
Video Standard
Closed Caption
Ceiling Mount
RGB
Auto
Off
Rear Project
Prevent PC Screen Saver
i
Off
Off
On
Adjust Color, Tint, Brightness, Contrast in the Basic
Picture menu
Correct image
Basic Picture
COLOR
i
Brightness
Contrast
Sharpness
Color
Tint
Auto Image...
Aspect Ratio
Apply Preset...
50
50
Maximum
50
50
Auto
21
COLOR
Problem
Solution
Result
The video embedded in my PowerPoint
presentation does not play on the screen
Turn off the internal LCD display on your laptop
Embedded video plays correctly
A
A
B
A
B
A
B
Lamp won’t turn on, Temperature light is on
Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Lamp turns on
Startup
Screen
Temperature light
22
B
Problem
Solution
Result
“Replace lamp” message appears at startup, lamp
won’t turn on, Lamp light is turned on
Lamp must be replaced (see page 47)
Lamp turns on
lamp door
Lamp light
replace lamp
Still need assistance?
If you need assistance, visit our website at www.infocus.com/support or call us.
Check out our HOW TO section there for additional information on using this
projector for home theater or gaming applications. See the Quick Start Poster/
Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan may be
purchased from your dealer. When sending the projector in for repair, we
recommend shipping the unit in its original packing material, or having a
professional packaging company pack the unit. Please insure your shipment for its
full value.
23
Startup
Screen
Using the remote control
The remote uses two (2) AA batteries (not provided). They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
•
•
•
•
Caution:
Troubleshooting the remote
•
When replacing the remote batteries, be aware that using batteries other than
AA batteries may risk severe damage to the remote. When disposing of the
batteries, be sure to do so in an enviromentally proper manner.
If the remote control gets wet, wipe it dry immediately.
•
Avoid excessive heat and humidity.
•
Ensure the batteries' polarity (+/-) is aligned correctly.
•
Do not mix new and old batteries together, or mix different types of batteries
together.
•
•
Replace the batteries as soon as they run out.
•
Remove batteries from the remote control when storing or not in use for a prolonged period.
•
•
Press the remote’s Power button to turn the projector on and off (see page 12 for
shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use the arrow
buttons to navigate, and the Select button to select features and adjust values in the
menus. See page 30 for more info on the menus.
The remote also has:
•
•
•
Make sure the batteries are installed in the proper orientation and are not dead.
Make sure you’re pointing the remote at the projector or the screen, not the
computer, and are within the remote range of 15 feet (4.5m). For best results,
point the remote at the projector.
navigation
buttons
To operate, point the remote at the front of the projector (not at the computer). The
range of optimum operation is about 15 feet (4.5m).
•
•
Mute button to silence the audio.
Auto Image button to resynch the projector to the source.
Resize button to switch among aspect ratios (see page 31).
Help button to get help with connecting sources and improving the picture.
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank Screen or
Freeze (see page 33).
Source button brings up a menu of all possible sources allowing the user to
switch the active source.
Blank button to blank the screen.
Presets button to select stored settings (see page 31).
24
Using the audio
connect audio cable
Using the projector’s speakers
USB A
USB mini B
Connect the audio source to either the Audio 1 or Audio 2 connectors to hear audio
through the projector speakers.
To assign the audio to a particular source, go to the Setup menu and choose the
Audio Inputs feature. Defaults are as follows: Audio 1 is set to VGA 1 and VGA 2
with microphone, and Audio 2 is set to Composite with audio. See page 33 for
details.
adjust volume
Amplified speakers may also be connected to the projector using the audio-out
connector.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
•
•
•
•
Make sure the audio cable is connected to the Audio 1 or 2 connector on the
projector, and that the other end of the cable is connected to an audio-out
connector on the source (not a “line-in” or “microphone” connector).
Make sure the volume is turned up enough. Press the Volume button on the
keypad or remote.
Make sure the correct source is active.
Adjust the audio source.
If playing a video, make sure the playback has not been paused.
25
Playing sound through the projector
About the microphone input
This projector is equipped with a 20-watt stereo speaker system, a dedicated
microphone input, and advanced audio processing for superb audio performance.
•
•
External amplified speakers may also be connected using the audio-out connector
on the projector.
If you wish to use a microphone, connect a 3.5 mini jack cable Dynamic
Microphone to the projector.
You can use a wireless microphone as long as a wireless module is attached to
the projector’s microphone input jack and it works well with the associated
devices. To ensure a quality use of the wireless microphone, it is recommended
that your microphone conforms to the specifications listed in the table below.
This system has assignable audio. Audio 1, Audio 2 and/or the microphone can be
assigned in any combination through the Audio Inputs feature described on
page 33. NOTE: The microphone audio can be used alone (with other audio
muted), or in conjunction with other audio simultaneously. The mixing of the
microphone audio and other audio inputs is handled through the Mic Volume menu.
•
By default, Audio 1 plus microphone is associated with VGA 1 and VGA 2. Audio
2 plus microphone is associated with the Composite Video.
Signal
Parameter
Microphone
Transducer Principle
Impedance
Frequency response
Min
300
600
Max
1K
16k
Dynamic
ohm
Hz
There are two ways to adjust the microphone volume.
•
Adjust the microphone volume level in the Setup > Mic Volume menu.
•
Press the Volume key on the keypad or remote to adjust the volume of the
projector speaker and audio-out signal.
•
The microphone will work regardless of whether the projector is turned on or
soft-powered off, if the Always-On function “Microphone” is set to On.
•
If the microphone is not working, check the volume setting and cable
connection.
You might get feedback noise from the microphone when you are too close to the
speaker of the projector. Move the microphone away from the speaker of the
projector. The greater volume you require, the greater distance you need to be away
from the speaker to prevent feedback noise.
NOTE: Only Dynamic Microphones should be used. Do not use active (phantompowered) microphones as projector damage may occur.
26
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an overview of
their functions:
Power–turns the projector on and off (page 8).
Auto Image–resets the projector to the source (page 27).
Presets–cycles through the available preset settings (page 31).
Keystone–adjusts squareness of the image (page 9).
Menu–opens the on-screen menus (page 30).
Select–confirms choices made in the menus (page 30).
menu navigation
buttons
Up/Down/Left/Right arrows–navigates to and adjusts settings in the menus
(page 30).
Volume–adjusts sound (page 25).
Source–brings up a menu with all possible sources, allowing the user to change the
active source (page 8).
Help–accesses the projector’s help feature.
27
Optimizing computer images
Presentation features
After the projector is running and the image is on the screen, you can optimize the
image using the onscreen menus. For general information on using the menus, see
page 30.
Several features are provided to make giving presentations easier. Here is an
overview, details are found in the menu section.
•
•
•
•
•
•
•
Select default image settings using a preset appropriate to your environment.
Adjust the Keystone, Contrast, or Brightness (page 31).
Change the Aspect Ratio. Choose the option that best fits your input source
(page 31).
Adjust the Color Temperature (page 31).
Adjust the Phase, Tracking, or Horizontal or Vertical position (page 32).
Once you have optimized the image for a particular source, you can save the
settings using Presets. This allows you to quickly recall these settings later
(page 31).
•
•
28
The Custom key allows you to assign various features to the button. The
default effect is Source Info, which displays information about the projector
and current source. See page 33 for details.
The Search Screen option lets you change the appearance of the blank screen
and start up screen (page 34).
Two options, Auto Off and Screen Save Time, are provided to automatically
shut down the projector after several minutes of inactivity or display a black
screen. This helps preserve lamp life (page 33).
Optimizing video images
Dynamic Messaging
After your video device is connected properly and the image is on the screen, you
can optimize the image using the onscreen menus. For general information on using
the menus, see page 30.
Using command codes, text messages can be sent for display by the projector (and
all other InFocus projectors with the Dynamic Messaging feature) over a network or
serial connection. Text is shown on top of whatever else is being displayed, and can
be shown in ticker tape format or in a box, with optional beep tone alert. This is a
great way to display urgent alert messages to employees, and simply requires a
connection to the projector RS-232 serial control or LAN connector. Command
codes for executing Dynamic Messaging are available on our website at
www.infocus.com/support.
•
•
•
•
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint (page 31).
Change the Aspect Ratio. Choose the option that best fits your input source
(page 31).
Select a Sharpness setting (page 31).
Adjust the Color Temperature. Select a listed warmth value (page 32).
Turn on Overscan to remove noise on the edges of the image (page 32).
Customizing the projector
You can customize the projector for your specific setup and needs. See page 33 to
page 34 for details on these features.
•
•
•
•
•
•
•
•
•
For rear projection, turn Rear Project on in the Setup menu.
For ceiling mounted projection, turn Ceiling Mount on in the Setup menu.
Specify which source the projector checks first for active video during powerup.
Specify the function of the Custom key on the remote.
Turn the projector’s display messages on and off.
Turn on power saving features.
Specify appearance of blank screen and startup screen.
Specify the language viewed on the menus.
Save settings for the active source as a preset.
29
Using the menus
keypad navigation
buttons
To open the menus, press the Menu button on the keypad or remote. (The menus
automatically close after 60 seconds if no buttons are pressed.) Use the arrow
buttons to move up and down to highlight the desired menu, then press the Select
button.
To change a menu setting, highlight it, press Select, then use the up and down arrow
buttons to adjust the value or select an option or turn the feature on or off. Press
Select to confirm your changes. Use the arrows to navigate to another setting. When
your adjustments are complete, press Menu to access a different menu; press the
Menu button at any time to navigate to the higher-level menu and ultimately close
the menus.
•
•
•
•
Advanced Picture
Basic Picture
The menus are grouped by usage:
Brightness
Contrast
Sharpness
The Basic Picture menu provides common image adjustments.
The Advanced Picture menu provides more complex image adjustments.
The Setup menu provides set-up type adjustments that are not changed often.
The Status and Service menu provides information about the projector and
source.
BrilliantColor™
50
White Peaking
Color Temp
Maximum
50
Color
Tint
Auto Image...
Auto
i
Basic Picture menu
i
Power-up Source
USB Display Source
Composite SCART
Video Standard
Closed Caption
Ceiling Mount
Rear Project
Setup menu
30
50
Warmest
Off
Off
50
50
50
Sync Threshold
Tracking
Advanced Picture menu
Status and Service
Setup
Auto Source
Normal Look
Force Wide
Overscan
Phase
50
Aspect Ratio
Apply Preset...
i
50
Source Info
Projector Info
LiteBoard™ Info
Reset Lamp Hours...
Factory Reset...
Service Code...
On
VGA1
On
RGB
Auto
Off
Off
Off
i
Status and Service menu
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the up and
down arrows to adjust the values, then press Select to confirm the changes.
Basic Picture
Brightness
Brightness: changes the intensity of the image.
50
Contrast
Sharpness
Contrast: controls the degree of difference between the lightest and darkest parts of
the picture and changes the amount of black and white in the image.
50
Maximum
50
Color
Sharpness: (video sources only) changes the clarity of the edges of a video image.
Select a sharpness setting.
i
Color: adjusts a video image from black and white to fully saturated color. The
color setting applies to video sources only.
Tint
Auto Image...
50
Aspect Ratio
Auto
Apply Preset...
Basic Picture menu
Tint: adjusts the red-green color balance in the image of NTSC video images. The
tint setting applies to NTSC video sources only.
Basic Picture
Auto Image: resets the projector to the source.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height. TV
screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector. Select 16:9 to watch enhanced
widescreen DVDs.
For more information regarding Aspect Ratio, see page 10.
i
Brightness
Contrast
Sharpness
Color
Tint
Auto Image...
Aspect Ratio
Apply Preset...
50
50
Maximum
50
50
16:9
Apply Preset...: Presets are provided that optimize the projector for displaying
computer presentations and video images under certain conditions.
Auto
Native
4:3
16:9
16:10
Letterbox
Panorama
Aspect ratio
There is also a user-definable preset. To set this preset, adjust the image and select
Save User in the Presets menu. You can recall these settings in the future by
selecting the User preset.
Keystone: adjusts the image vertically and makes a squarer image. You can also
adjust keystone from the keypad.
Digital Zoom: reduces the size of projector’s display area. If the display area has
been resized by this setting, it can be moved by changing the Horz Shift and Vert
Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if its size
has been changed by the Digital Zoom setting.
increasing keystone
31
decreasing keystone
Advanced Picture menu
3D Sync Invert: (Only applies when 3D control is set to DLP Link™.) If the image
appears to flutter, look odd or if the image depth looks off or you experience eye
strain, turn this feature on to see if the image improves.
BrilliantColor™: produces an expanded on-screen color spectrum that delivers
enhanced color saturation for bright, true-to-life images. Choose Normal Look for
most video sources and Bright Look for most computer sources.
Gamma: select the appropriate gamma from among Video, Film, Bright, and CRT.
Red/Green/Blue Gain: adjusts the gain of the red, green or blue channel of the
image.
White Peaking: increases the brightness of whites that are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed relative
warmth value.
Red/Green/Blue Offset: adjusts the offset of the red, green or blue channel of the
image.
Force Wide: when this is off, the analog locking algorithms choose the standard
mode resolution (4:3) as the preferred default resolution. When this is on, the
analog locking algorithms choose wide mode resolution (16:10) as the preferred
default resolution.
Horizontal/Vertical Position: adjusts the position of a computer source.
Advanced Picture
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
BrilliantColor™
White Peaking
Sync Threshold: (progressive signals only) If a hardware device, such as a DVD
player, is not syncing properly with the projector, select this option to help it to sync
when connected to the projector.
Color Temp
Force Wide
Overscan
Phase
Tracking: adjusts the vertical scan of a computer source.
i
Color Space: applies to computer and component video sources. It allows you to
select a color space that has been specifically tuned for the input signal. When Auto
is selected, the projector automatically determines the standard. To choose a
different setting, turn off Auto, then choose RGB for computer sources or choose
either REC709 or REC601 for component video sources.
Sync Threshold
Tracking
Advanced Picture menu
Noise Reduction: reduces temporal and/or spatial noise in the image.
Set Black Level...: analyzes the current input image and calculates an offset value
which is then added to the analog to digital converter black level value. This
ensures optimum black level for each analog source.
Detect Film: determines whether the original source of the input video was film
(progressive) or video (interlaced).
3D Control: allows you to enjoy 3D (stereoscopic) content. Your IN3916 supports
two synchronization modes (External Sync and DLP Link™) for controlling LCD
shutter glasses. In addition to the projector, you will need a pair of 3D shutter
glasses, 3D content, and 3D compatible source (and emitter). Ensure the glasses
you choose are consistent with the synchronization mode you will be using. Note:
Enabling 3D Control disables LiteBoard.
32
Normal Look
50
Warmest
Off
Off
50
50
50
Setup menu
•
•
•
Language: allows you to select a language for the onscreen display.
Network: Allows you to setup network settings.
•
•
•
•
•
•
•
•
•
•
Blank Key: select what to display when the blank key on the remote is pressed:
your custom snapshot, a solid color screen (blue, black or white), the factory logo
screen, a timer, or test patterns. The timer option is useful for classroom tests or
break times during meetings.
DHCP: Turns the DHCP on or off.
IP Address: Assign Network IP Address.
Subnet Mask: Assign Network Subnet Mask.
Default Gateway: Assign Network Default Gateway.
WINS Host Name Lookup: Turns WINS Host Name Lookup on or off.
Host Name: Displays the host name.
MAC Address: Displays network MAC Address value.
Show Network Messages: Turns network messages on or off. Network
messages display the projector’s IP address (and host name if enabled) when
the projector is also displaying source messages.
Restart Network...: Restarts the network.
Network Factory Reset...: Performs factory reset.
Source Keys: Enables or disables Source Keys on the optional Commander-2
remote.
AC Power On: When this feature is on, the projector automatically turns on when
electrical power is connected. This allows control of ceiling mounted projectors
with a wall power switch.
Auto Off Time: automatically turns the projector off after no signals are detected
for a preset number of minutes. If an active signal is received before the projector
powers down, the image will be displayed.
Screen Save Time: automatically blanks the screen with a black color after no
signals are detected for a preset number of minutes. The image returns when an
active source is detected or a remote or keypad button is pressed.
LiteBoard™Wand: allows you to control the operation of the LiteBoard Wand.
Note: Enabling LiteBoard disables 3D Control.
Sleep Timer: Allows the projector to automatically power off after it has been on
for a specified amount of time.
Mic Volume: adjusts the relative volume of the microphone versus audio-in.
Always-On Functions: allows you to control which projector functions will work
even when the projector is in standby (powered off but connected to AC Power).
Press Up or Down to highlight the function you want to change, then press select or
left and right to change the function to either Yes or No. Press menu when done.
Note that some functions must always have the same value; in this case when you
change one value, other values in the submenu may also change automatically.
Functions which can be adjusted include: 5-Volt DC Output, Mic Input, Monitor
Out, Network and USB Display.
Key Click: turns the key click sound on or off. When this setting is on, pressing
keys on the keypad causes the projector’s speaker to play a “click” sound.
Custom Key: allows you to assign a different function to the Custom button,
allowing you to quickly and easily use the effect. Highlight an effect and press
Select to choose a different one.
•
•
•
•
•
•
•
•
Overscan: removes noise around the image.
AV Mute: enables or disables AV Mute function.
Closed Captions: enables or disables Closed Captions.
Blank Screen: displays an empty screen.
Mute: turns off all sound.
Aspect Ratio: toggles among 4:3, 16:9, 16:10, Native, Letterbox and
Panorama options (see page 10 and page 31).
Source: cycles through available sources.
Auto Image: resets the projector to the source (page 27).
Freeze Screen: pauses the projected image.
Source Info: the default action. Shows the Source Info menu.
Projector Info: shows the Projector Info menu.
Lamp Low Power: toggles between on and off. Turn it on to lower the light output
of the lamp. This also lowers the fan speed, making the projector quieter.
Power Sounds: controls whether the projector makes a sound when powered on
and off.
Internal Speaker: turns the internal speaker on or off.
Audio Inputs: assign an audio input to a specific video/computer source input.
Press up or down to highlight the source you want to change, then press Select or
33
the left and right arrow keys to change the source’s audio input. Press Menu when
done changing audio inputs.
captions on the selected channel, then the projector must display caption text
overlaid on the image.
Auto Source: When this feature is On, the projector automatically finds the active
source, checking the selected Power-up Source first. When this feature is Off, the
projector defaults to the source selected in Power-up Source. To display another
source, you must manually select one by pressing the Source button on the remote
or keypad.
Closed Captions (unmuted): controls closed caption display while audio is not
muted. If this setting is not off, and audio is not muted, and the source is NTSC and
contains captions on the selected channel, then the projector must display caption
text overlaid on the image.
Ceiling Mount: turns the image upside down for ceiling-mounted projection.
Rear Project: reverses the image so you can project from behind a translucent
screen.
Setup
i
Auto Source
Power-up Source
USB Display Source
Composite SCART
Video Standard
Closed Caption
Ceiling Mount
Rear Project
Prevent PC Screen Saver: prevents your computer from going into Screen Save
mode. The projector must be connected to the PC via a USB cable for this feature to
work.
On
VGA1
On
RGB
Auto
Off
Off
Off
Search Screen: allows you to display a blank screen instead of the default screen at
startup, and when no source is detected.
Take Snapshot...: captures the current image and allows it to be used as the search
screen image.
Disable Snapshot: allows the user to disable the snapshot capability.
Setup menu
Show Messages: displays status messages (such as “Searching”) in the lower-left
corner of the screen.
Power-up Source: determines which source the projector checks first for active
video during power-up.
Menu Offset: allows you to change the position of the On Screen Display items.
USB Display Source: when enabled, allows the USB mini-B to display images
over USB.
Menu Transparency: allows you to change how much of the projected image
behind the menu you can see. As the value increases, more of the image behind the
menu is visible.
Composite SCART: selects SCART connection type. This setting is only used for
projectors where SCART can be connected to a single existing source (e.g. VGA),
not on projectors where SCART must be connected to multiple sources (e.g.
composite + component).
Magnify Controls: determines whether the select key can be used to change
magnify settings when the OSD menu is not visible.
Keypad: enables or locks the projector keypad.
Video Standard: When this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives. (The
video standard options may vary depending on your region of the world.) If the
projector is unable to detect the correct standard, the colors may not look right or
the image may appear “torn.” If this happens, manually select a video standard by
selecting NTSC, PAL, or SECAM from the Video Standard menu.
Glow Ring: controls the appearance of the optional glow ring status indicator.
PIN Protect: The PIN (personal identification number) feature allows you to
password protect your projector. Once you enable the PIN feature, you must enter
the PIN before you can project an image. The default PIN on this projector is
Menu-Source-Select-Up-Down. Use the navigation buttons on the remote or
keypad to enter the correct 5-button press sequence. When all 5 numbers are entered
correctly, press the Select button on the remote or keypad to select OK. If the
message “Wrong PIN” appears, verify the code and re-enter it. If you mis-enter a
Closed Captions (muted): controls closed caption display while audio is muted. If
this setting is not off, and audio is muted, and the source is NTSC and contains
34
number, you must enter 5 numbers and press the Select button in order to access the
“Wrong PIN” message and re-enter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the startup screen.
Enter the PIN. Use the navigation buttons on the remote or keypad to enter the
correct button press sequence. See the description above for instructions.
To change the PIN:
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the new
PIN. You can navigate between OK and Cancel by pressing the up and down
buttons on the keypad. Select OK or Cancel by pressing the Select button. Verify
the new PIN.
If you lose or forget your custom PIN: Contact InFocus support. Go to
www.infocus.com/support
Serial Port Baud Rate: selects the serial port and baud rate.
Serial Port Echo: controls whether the serial port echoes characters.
35
Status and Service menu
Source Info: a read-only display of current source settings.
Status and Service
Projector Info: a read-only display of current projector settings.
Source Info
LiteBoard™ Info: a read-only display of current LiteBoard™ settings.
Projector Info
LiteBoard™ Info
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info menu
to zero. Do this only after changing the lamp.
Reset Lamp Hours...
Factory Reset...
Service Code...
Factory Reset: restores all settings to their default.
i
Service Code: only used by authorized service personnel.
Status and Service menu
36
Using LitePort
LitePort displays a slide show of JPEG images stored on a USB flash drive
connected to the projector or a Presentation To Go presentation. This can eliminate
the need for a computer source. LitePort reads and displays files stored on a USB
flash drive in either JPEG or Presentation-to-Go format (PtG). LitePort ignores all
other file formats including PDF, BMP, TIFF, PNG, GIF, etc. which are not
supported. (Note: Microsoft and others provide applications which convert
PowerPoint presentations into a series of JPEG files.)
LitePort menu
Displaying JPEG images
1 Connect a USB flash drive to your computer and copy JPEG files from your
computer to the USB flash drive.
2 Turn on your projector if needed.
3 Remove the USB flash drive from your computer and plug it into the USB A
connector on the rear of the projector.
4 The projector will display the LitePort menu.
5 Click JPEG and navigate to the desired image using the arrow buttons on the
projector keypad or remote.
6 Click Select to display the desired image.
7 If multiple images exist in the same folder, the arrow buttons can be used to
navigate through the images in alpha-numeric order. NOTE: The arrow buttons
will not auto-scroll from the last image to the first image in the folder, nor will it
auto-scroll from the first image to the last image in the folder.
8 To stop displaying the LitePort image, click the Menu button.
37
7 Use the arrow buttons to navigate through the presentation.
Displaying PtG presentations
Follow these steps to show a slideshow presentation using Presentation-to-Go (PtG)
presentation. This will preserve most PowerPoint embedded videos, transition
effects, and animations. (Note: these instructions apply to PowerPoint 2007 in
Windows; for other presentation programs refer to the presentation program's
instructions or help file for the steps needed to save a presentation as separate JPEG
files.)
To stop displaying the presentation: click the Menu button.
Troubleshooting LitePort
•
If images load slowly: Make sure you are using a newer USB 2.0compatible (high speed) USB flash drive. Larger image file sizes may also
slow down the player; to reduce file size, use an image editing program on
your computer to resize images smaller; for the best balance between image
quality and speed, resize images to be 1024 pixels wide.
•
If no images are found, or some images are not shown, or you only see folder
thumbnails but no images: Make sure that images are JPEG file type (file
extensions .JPEG and .JPG); other file types are not supported and will be
ignored.
•
Using the Source button, make sure you have the LitePort source selected and
make sure your USB flash drive is correctly and completely plugged in to the
projectors LitePort connector.
•
If nothing happens when you connect your USB flash drive, and you cannot
select the LitePort input source as described above: Check the format of your
USB storage device. LitePort only supports USB storage devices formatted as
FAT32. Devices formatted as NTFS, and non-storage devices (such as
cameras) are not supported.
To convert a PowerPoint presentation to a PtG presentation:
1 Download and install the PtG Converter software onto your computer (available on www.infocus.com/support).
2 Close all open computer applications.
3 Open the PtG Converter Lite program and click the Convert button.
4 Navigate to the desired PowerPoint presentation and click OK to begin conversion.
5 When the conversion is complete, a “Conversion Complete” message will display. Click OK.
To display the PtG presentation:
1 Connect a USB flash drive to your computer and copy PtG presentation from
your computer to the USB flash drive.
2 Turn on your projector if needed.
3 Remove the USB flash drive from your computer and plug it into the USB A
connector on the rear of the projector.
4 The projector will display the LitePort menu.
5 Click PtG and navigate to the desired presentation using the arrow buttons on
the projector keypad or remote.
6 Click Select to display the desired presentation.
38
LiteShow
LiteShow Login Screen
The LiteShow Utility embedded in your projector provides many new features to
make your presentations even more effective. Once installed, the Utility allows you
to configure, control and display to your projector from a computer or PDA over
either a wired or wireless LAN connection. It also allows you to display up to 4
computer screens simultaneously, and includes a moderator control, allowing you
to control the display of up to 32 computers.
•
Supports Windows 7, Vista, XP, 2000 and Mobile 5/6
•
Supports Macintosh (Mac) version 10.4 and later
•
Provides security login, wireless WEP/WPA key and Gatekeeper function to
protect information from theft
LAN Connection
At the LiteShow Login screen, enter one of the following combinations to access
associated LiteShow menus:
LiteShow supports wired and wireless LAN connectivity for projector control and
display. There are three set-up options available.
•
•
•
Wired only: projector can be accessed over the connected LAN
Wireless only: projector creates a wireless LAN which can be accessed by
802.11b/g enabled computers.
Both wired and wireless: projector creates a wireless LAN which can be
accessed by 802.11b/g enabled computers and which also can provide an
Access Point through the wired connection to the larger corporate network.
Projector can be accessed through either ether wireless or wired network.
Setting up a LAN connection:
Select the LAN source on the projector which will display the LiteShow splash
screen. Establish a network connection from your computer to the projector based
on the wired and/or wireless set-up implemented when the projector was installed.
Open a web-browser window and type the projector’s IP address to connect to the
projector’s LiteShow Login screen.
Login
Default Password
Menu Options
None
Leave blank
Basic User
trainer
Admin User
admin
Download
System Status
Download
System Status
Basic Projector Control
Moderator Control
Download
System Status
Basic Projector Control
Moderator Control
Admin Menu
If the default password listed above does not work, contact your IT administrator.
39
LiteShow Menu Options
Notes: Projector web pages and emails sent by the projector are always displayed in
English language. Select the web pages language (English, Traditional Chinese,
Simplified Chinese, Korean, German, French, Italian, Spanish, Polish, Swedish,
Dutch, Portuguese, Russian, Finnish, Norwegian, Turkish, or Danish) on the home
page. For network control, you can access the projector through Port 23 (Telnet).
We use the same control codes on serial as we do over the network. InFocus
network control uses the Telnet packet structure.
Download
This menu allows the user to download the LiteShow Utility to their computer.
Follow the Download LiteShow Utility instructions below.
System Status
This menu allows the user to review the network and connection status, and the
source and projector information. This is particularly useful when troubleshooting.
Network Setup: Before the LiteShow features can be used, the projector must be
configured within this submenu for your network. Consult with your network
administrator before entering information into this submenu. Incorrect network
information may cause problems on your network. Note: To enable network
functions at all times (even when the projector is powered off), the Network item in
the Always-On Functions submenu in the Setup menu must be set to Yes (not No).
Basic Projector Control
Note: To gain access to the Basic Menu, you must be logged in as a Basic or Admin
User.
This menu allows the user to control many of the projector’s Basic Picture and
Setup OSD menu features through the network. These include: Power on/off,
Brightness, Contrast, Sharpness, Color, Tint, Auto Image, Aspect Ratio, Apply Presets, Custom Key, Blank Key, source, AC Power, Internal Speakers, Audio Inputs,
Volume, Mic Volume and Mute.
IP Setup: Wired LAN settings if DHCP is turned off or not available on the
Wired LAN.
DHCP Server Setup: The projector acts as a DHCP host whenever hosting a
Wireless LAN and/or whenever connected to a Wired LAN which doesn’t
include a DHCP Host.
Moderator Control
Note: To gain access to the Moderator Control Menu, you must be logged in as a
Basic or Admin User.
Wireless Setup: IP configuration of the Wireless LAN – these control how the
projector’s Wireless LAN appears to computers on the Wireless network
hosted by the projector.
This menu allows the user to control who displays to the projector. Note: Up to 32
computers can be connected to the LiteShow network, however only four
computers can be displayed simultaneously. See instructions below.
GateKeeper: Client computers on the Wireless LAN can access the broader
LAN/Internet over the Wired LAN connection if enabled here. Internet Only
blocks IP addresses on the same LAN subnet as the projector, but allows
access to other IP addresses.
Admin Menu
CLI Pass-Through: The projector includes a basic Telnet engine. You can
“Enable” an incoming Telnet connection in which the projector will parse and
respond to CLI commands received on this port (23).
Note: To gain access to the Admin Menu, you must be logged in as an Admin User.
Use the Admin Menu for configuring and controlling the projector via a web
browser, setting up failure and warning alerts via email, managing the projector via
SNMP.
SNMP: Configure Simple Network Management Protocol settings.
Crestron Control System: Enable control by Crestron systems.
40
AMX Control System: Enable control by AMX systems.
Projection Setup: Select the LiteShow display resolution and set-up (or disable)
login codes within this menu.
Menu Sample: System Status menu
Change Passwords: Enter, confirm and apply new passwords for each Login type.
Apply confirms and saves your modifications.
Reset to Default: Clicking the Reset to Default button restores factory default
settings.
Advance Projector Control: Allows the user to control many of the projector’s
Advanced Picture OSD menu features through the network. These include:
defaulted language, Auto-off Time, Low Power, Auto Source, Power Up Source,
Closed Captions, Ceiling Mount, Rear Projection, Splash Screen, Magnify
Controls, and Keypad, PIN and Serial Port controls.
Alert Settings: If your projector is connected to a network which supports Simple
Mail Transfer Protocol (SMTP), you can configure it to alert you via email on
significant events. Examples of possible event alert emails include lamp did not
strike, lamp went out unexpectedly, fan failure, over-temperature, lamp hours.
Firmware Upgrade: The LiteShow Utility stored on the projector can be upgraded
via the Firmware Upgrade option. When Firmware Upgrade>Upgrade has been
selected, a warning message and count-down counter will be shown on the screen.
A complete message will be shown on the screen within a few minutes. A projector
restart will be required to complete the upgrade process.
41
Menu Sample: Basic Projector Control menu
Menu Sample: Admin > Network menu
42
Downloading the LiteShow Utility:
To begin projecting over the local network or wirelessly, the LiteShow Utility must
be installed and running on your computer or PDA. This Utility is needed to manage the communication between your computer/PDA and the LAN-connected projector.
LiteShow Download menu
1 Turn the projector on, hit the Source button and select LAN. The LiteShow
splash screen should appear within one minute.
2 You must be connected to the projector through a wired or wireless LAN. For
wireless LAN, connect to the wireless network using the same SSID as shown
on the projector.
3 Enter the IP address displayed on the projector into your web browser. (Note:
The default IP address of LiteShow is 192.168.100.10)
4 Login as None and select Download.
5 Download and install the appropriate LiteShow application based on your operating system (Windows 7/Vista/XP/2000, Windows Mobile 5.0 or Macbook
10.4 and later).
6 Follow the Installation Wizard instructions.
7 Once the installation is complete, a LiteShow shortcut will be available on your
LiteShow Shortcut
desktop.
43
To display your computer/PDA image over the LAN:
Access Point prompt
1 Turn the projector on, hit the Source button and select LAN. The LiteShow
Device Name list
splash screen should appear within one minute.
2 You must be connected to the projector through a wired or wireless LAN. For
wireless LAN, connect to the wireless network using the same SSID as shown
on the projector.
3 Download and install the LiteShow Utility, if you have not already done so.
4 At the Access Point prompt, select the appropriate wireless connection to the
projector or choose SKIP for a wired LAN connection.
5 Select the projector from the Device Name list.
6 Enter the Login Code, if prompted.
7 Begin presenting.
Login screen
LiteShow Splash Screen
44
To control the projected image:
Use the LiteShow Toolbar to switch between full screen projection and QuadView
projection. You can also choose to refresh, pause or stop projecting. Various
administration tools are also available through this control.
LiteShow Toolbar
Play
Quadrant 1
Quadrant 3
To moderate multiple users:
Quadrant 2
Quadrant 4
LiteShow Moderator Control
Note: You must be logged in as an Admin User to be able to control who is
projecting.
From the Moderator Control menu, a list of users can be viewed. Using the Play
Control buttons, choose one or more users (up to four simultaneously) to display.
Choices include: Full display, Quadrant 1, Quadrant 2, Quadrant 3, Quadrant 4, or
Stop (projecting).
45
Stop
Pause
Additional options
Refresh
Status
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Projector must be off and the lens must be at room temperature.
• Avoid using an excessive amount of cleaner, and don’t apply the cleaner
directly to the lens. Abrasive cleaners, solvents or other harsh chemicals
might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
WARNINGS:
• Turn the projector off and unplug power cord before cleaning any part of the
projector.
USB A
USB mini B
• Do not touch or block the projector lens with any objects as this can damage
the projector lens. Use the lens cap when the projector is not in use and
during transport. Scratches, gouges and other lens damage are not covered
by the product warranty.
• Do not open any cover on the projector, except the lamp cover.
• Do not attempt to service this product yourself as opening and removing
covers may expose you to dangerous voltage and other hazards. Refer all
servicing to qualified service personnel.
security
lock
Using the security lock
The projector has a security lock for use with a Cable Lock System. Refer to the
information that came with the lock for instructions on how to use it.
46
Replacing the projection lamp
The Lamp Hours timer in the Projector Info menu counts the number of hours the
lamp has been in use. Twenty hours before the lamp life expires, the message
“Replace lamp” appears on the screen at startup.
•
•
IMPORTANT NOTE:
•
Always use the InFocus lamp module designed for your projector model. Look
at the 8th character of the projector’s serial number (located on the bottom of
the projector and in the Service and Support>Projector Info submenu).
•
If the 8th character is a “0” (Example: BFQMyww0nnnn) Use SP-LAMP-062
•
If the 8th character is an “A” (Example: BFQMywwAnnnn) Use SP-LAMP062A
•
These lamps are NOT interchangeable, and are only designed to fit
into compatible products.
•
Be sure to use the InFocus lamp module designed for this projector. You can
order new lamps from www.infocus.com (in select areas), your retailer or your
dealer. Only genuine InFocus lamps are tested for use in this projector. Use
of non InFocus lamps may cause electrical shock and fire, and may void the
projector warranty. InFocus is not liable for the performance, safety or
certification of any other lamps.
•
WARNINGS:
•
•
•
•
•
•
The projector uses a high-pressure mercury glass lamp. The lamp may fail
prematurely, or it may rupture with a popping sound if jolted, scratched, or
handled while hot. The risk of lamp failure or rupture also increases as the
lamp age increases; please replace the lamp when you see the “Replace Lamp”
message.
To avoid burns, allow the projector to cool for at least 60 minutes before you
replace the lamp.
Unplug the power cord before replacing the lamp.
Do not drop the lamp module. The glass may shatter and cause injury.
Do not touch the glass surface of the lamp module. Fingerprints can obscure
projection sharpness and may cause the glass to shatter.
Be extremely careful when removing the lamp housing. In the unlikely event
that the lamp ruptures, small glass fragments may be generated. The lamp
47
module is designed to contain most of these fragments, but use caution when
removing it.
Before replacing a ruptured lamp, clean the lamp compartment and dispose of
cleaning materials. Wash hands after lamp replacement.
When replacing the lamp while the projector is ceiling-mounted, wear
protective eyewear to prevent eye injury.
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
1 Turn off the projector and unplug the power cord.
USB A
2 Wait 60 minutes to allow the projector to cool thoroughly.
turn off and unplug
projector
USB mini B
wait 60 minutes
3 Remove the lamp door, located on top of the projector, by (a) removing the two
screws on either side of the lamp door, (b) sliding the lamp door towards the
front of the projector, and (c) tilting and lifting the door off.
4 Disconnect the lamp connector.
5 Loosen the captive screw that attaches the lamp housing to the projector.
NOTE: If the projector is installed on a ceiling mount, be careful not to drop the
lamp module once the captive screw is loosened.
6 Carefully lift the lamp straight up, off of the alignment pins; being careful not to
pinch the lamp connector. Dispose of the lamp in an environmentally proper
manner.
Disconnect lamp Connector
loosen screw
7 Install the new lamp module, aligning the pins properly. Be careful not to pinch
the lamp connector.
8 Tighten the screw. (NOTE: If the pins have not been aligned properly, the
screw will not tighten securely.)
9 Re-attach the lamp connector to the projector.
10 Replace the lamp door by (a) aligning the hinges, (b) putting the lamp door
down and (c) sliding it back into place.
11 Replace the lamp door screws and tighten securely.
Status and Service
12 Plug in the power cord and press the Power button to turn the projector back on.
Source Info
Projector Info
LiteBoard™ Info
Reset Lamp Hours...
Factory Reset...
Service Code...
13 To reset the lamp hour timer, navigate to the Status and Service menu and
select Reset Lamp Hours. See page 36 for details.
i
48
Digital Zoom 31
Disable Snapshot 34
Display Image over LAN 44
Download LiteShow Utility 43
Dynamic Messaging 29
INDEX
Numerics
16x9 vs 4x3 11
3D Control 32
3D Sync Invert 32
F
Factory Reset 36
Focus 9
Force Wide 32
Freeze Screen 33
A
AC Power On 33
Always-On Functions 33
Apply Preset 31
Aspect Ratio 11, 31
Audio In Computer connector 7
Audio Inputs 33
Auto Image 31
Auto Off Time 33
Auto Source 33
AV Mute 33
G
Gamma 32
Glow Ring 34
H
HDTV 31
Horizontal Position 32
Horz Shift 31
B
I
Battery Light 14
Blank Key 33
Blank Screen 33
Brightness 31
Internal Radio 14
Internal Speaker 33
K
Key Click 33
Keypad 34, 27
Keystone 31
Keystone, Adjusting 9
C
Cable Box 11
Ceiling Mount 34
Click Speed 14
Closed Captions 33, 34
Color Space 32
Computer In connector 7
Connecting
Video device 11
Contacting InFocus 23
Contrast 31
Customer service contact information 23
L
Lamp Low Power 33
Lamp Replacement 47
Language 33
Lens Cleaning 46
Link Channel 14
Link Light 14
LiteBoard™ Info 36
LiteBoard™ Wand 33
LitePort 37
LiteShow 39
D
Detect Film 32
49
LiteShow Menu Options 40
LiteShow Moderator 40, 45
Reset Button 14
Resetting the projector 36
M
S
Magnify Controls 34
Menu Offset 34
Menu Transparency 34
Menu usage 30
Mic Volume 33
Motion 14
Mute 33
Screen Aspect 11
Screen Save 16, 33
Scroll Wheel Mode 14
Search Screen 34
Security Lock 46
Sensor 14
Serial Port Baud Rate 35
Serial Port Echo 35
Service 36
Set Black Level... 32
Sharpness 31
Show Messages 34
Sleep Timer 33
Source 33
Source Info 33, 36
Source Key 33
Sync Threshold 32
N
Noise Reduction 32
O
Overscan 32, 33
P
Phase 32
PIN Protect 34
Power connector 7
Power cord 7
Power Sounds 33
Prevent PC Screen Saver 34
Projector
Connecting video devices 11
Keypad buttons 27
Menus 30
Positioning 6
Setting up 6
Troubleshooting problems 16
Projector Info 33, 36
PtG Presentation 38
T
Take Snapshot... 34
Tint 31
Tracking 32
Troubleshooting 16
TV tuner 11
U
Undo Button 14
USB 5, 7,14
V
Vert Shift 31
Vertical Position 32
Volume button 25
R
Rear Project 34
Red/Green/Blue Gain 32
Red/Green/Blue Offset 32
Remote control 24
Reset 36
W
Warranty 23
50
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement