Infocus | IN5316HD | User's Manual | InFocus IN5316HD User's Manual

InFocus IN5316HD User's Manual
Copyright
This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be
reproduced without written consent of the author.
© Copyright 2011
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple Computer, Inc. IBM
is a trademark or registered trademark of International Business Machines, Inc. Microsoft, PowerPoint,
and Windows are trademarks or registered trademarks of Microsoft Corporation. Adobe and Acrobat are
trademarks or registered trademarks of Adobe Systems Incorporated. DLP®, DLP Link and the DLP logo
are registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of Texas Instruments.
InFocus, In Focus, and INFOCUS (stylized) are either registered trademarks or trademarks of InFocus
Corporation in the United States and other countries.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or registered trademarks
of HDMI Licensing LLC in the United States and other countries.
DisplayPort is a registered trademark of the Video Electronics Standards Association, registered in
the U.S. and the other countries.
All other product names used in this manual are the properties of their respective owners and are acknowledged.
—i—
User’s Manual
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause personal injury.
Throughout this manual, component parts and items in the On-Screen Display (OSD) menus are denoted
in bold font as in this example: “Push the MENU button on the remote control to open the DISPLAY
menu.”
General Safety Information
¾
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact InFocus at www.infocus.com/support
¾
Follow all warnings and cautions in this manual and on the unit case.
¾
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
¾
Do not place the unit on an unstable surface, cart, or stand.
¾
Avoid using the system near water, in direct sunlight, or near a heating device.
¾
Do not place heavy objects such as books or bags on the unit.
Caution:
Avoid using the projector in dusty environments.
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
— ii —
Preface
Projector Installation Notice
¾
Place the projector in a horizontal position
The tilt angle of the projector should not exceed 15 degrees, nor should the projector be installed in
any way other than the desktop and ceiling mount, otherwise lamp life could decrease dramatically.
¾
Allow at least 50 cm (19.69 inch) clearance around the exhaust vent.
(19.69 inch)
(19.69 inch)
(19.69 inch)
(3.94 inch)
(11.81 inch)
(19.69 inch)
¾
Ensure that the intake vents do not recycle hot air from the exhaust vent.
¾
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed 5 – 35°C (41– 95°F) while the projector is running, and the
air intake and exhaust vents are unobstructed.
¾
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
within the acceptable 5 – 35°C (41– 95°F) range.
Power Safety
¾
Only use the supplied power cord.
¾
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
¾
Remove the batteries from the remote control when storing or not in use for a prolonged period.
– iii –
User’s Manual
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 39
for clear and safe instructions for this procedure. Before replacing the lamp:
¾
Unplug the power cord.
¾
Allow the lamp to cool for about one hour.
Cleaning the Projector
¾
Unplug the power cord before cleaning. See Cleaning the Projector on page 42.
¾
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance section
on page 54.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
laws. For more information, contact the Electronic Industries Alliance at www.eiae.org. For lamp specific
disposal information check www.lamprecycle.org.
Symbol Explanations
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector. Wherever possible, relevant information—such as an illustration and its description—has been kept on one
page. This printer-friendly format is both for your convenience and to help save paper, thereby protecting
the environment. It is suggested that you only print sections that are relevant to your needs.
— iv —
Preface
Table of Contents
GETTING STARTED........................................................................................................................................................... 1
PACKING CHECKLIST ........................................................................................................................................................... 1
VIEWS OF PROJECTOR PARTS ............................................................................................................................................... 2
Front-angled View ........................................................................................................................................................ 2
Top view—On-screen Display (OSD) buttons ......................................................................................................... 3
Rear view....................................................................................................................................................................... 4
Bottom view................................................................................................................................................................... 6
REMOTE CONTROL PARTS ................................................................................................................................................... 7
SETUP AND OPERATION................................................................................................................................................. 9
INSERTING THE REMOTE CONTROL BATTERIES ................................................................................................................... 9
INSTALLING OR REMOVING THE OPTIONAL LENS .............................................................................................................. 10
Removing the Existing Lens From the Projector ................................................................................................... 10
Installing the New Lens ............................................................................................................................................. 11
STARTING AND SHUTTING DOWN THE PROJECTOR ............................................................................................................. 12
ADJUSTING THE PROJECTOR LEVEL ................................................................................................................................... 14
ADJUSTING PROJECTED IMAGE POSITION USING SHIFT ..................................................................................................... 15
Adjusting the vertical image position ....................................................................................................................... 15
Adjusting the horizontal image position .................................................................................................................. 16
Shift Range Diagram ................................................................................................................................................. 16
ADJUSTING ZOOM, FOCUS AND KEYSTONE ....................................................................................................................... 17
ADJUSTING THE VOLUME .................................................................................................................................................. 18
ON-SCREEN DISPLAY (OSD) MENU SETTINGS ...................................................................................................... 19
OSD MENU CONTROLS ..................................................................................................................................................... 19
Navigating the OSD ................................................................................................................................................... 19
SETTING THE OSD LANGUAGE .......................................................................................................................................... 20
OSD MENU OVERVIEW ..................................................................................................................................................... 21
PICTURE>>BASIC MENU................................................................................................................................................. 22
PICTURE>>ADVANCED MENU ........................................................................................................................................ 23
HSG Adjustment......................................................................................................................................................... 24
DISPLAY MENU ............................................................................................................................................................... 25
PC Detail Adjustment................................................................................................................................................. 26
SETUP>>BASIC MENU ..................................................................................................................................................... 27
Menu Settings ............................................................................................................................................................. 28
Source.......................................................................................................................................................................... 29
Lan Control Settings .................................................................................................................................................. 30
SETUP>>ADVANCED MENU ............................................................................................................................................ 34
Audio ............................................................................................................................................................................ 35
Lamp ............................................................................................................................................................................ 36
HDMI ............................................................................................................................................................................ 36
Closed Caption ........................................................................................................................................................... 37
Presentation Timer..................................................................................................................................................... 37
STATUS MENU ................................................................................................................................................................ 38
MAINTENANCE AND SECURITY .................................................................................................................................. 39
REPLACING THE PROJECTION LAMP................................................................................................................................... 39
CLEANING THE PROJECTOR................................................................................................................................................ 42
Cleaning the Lens ...................................................................................................................................................... 42
Cleaning the Case...................................................................................................................................................... 42
TROUBLESHOOTING...................................................................................................................................................... 43
COMMON PROBLEMS AND SOLUTIONS............................................................................................................................... 43
TIPS FOR TROUBLESHOOTING ............................................................................................................................................ 43
LED ERROR MESSAGES ..................................................................................................................................................... 44
IMAGE PROBLEMS .............................................................................................................................................................. 44
LAMP PROBLEMS ............................................................................................................................................................... 45
REMOTE CONTROL PROBLEMS .......................................................................................................................................... 45
–v–
User’s Manual
AUDIO PROBLEMS ............................................................................................................................................................. 46
HAVING THE PROJECTOR SERVICED .................................................................................................................................. 46
HDMI Q & A .................................................................................................................................................................... 47
SPECIFICATIONS ............................................................................................................................................................. 48
SPECIFICATIONS................................................................................................................................................................. 48
PROJECTION DISTANCE VS. PROJECTION SIZE (1080P) ..................................................................................................... 49
Projection Distance and Size Table .............................................................................................................................. 49
PROJECTION DISTANCE VS. PROJECTION SIZE (WUXGA) ................................................................................................ 50
Projection Distance and Size Table .............................................................................................................................. 50
TIMING MODE TABLE ........................................................................................................................................................ 51
PROJECTOR DIMENSIONS ................................................................................................................................................... 53
REGULATORY COMPLIANCE....................................................................................................................................... 54
FCC WARNING .................................................................................................................................................................. 54
CANADA ............................................................................................................................................................................ 54
WEEE ............................................................................................................................................................................... 54
SAFETY CERTIFICATIONS ................................................................................................................................................... 54
— vi —
IN5316HD/IN5318 – User’s Manual
GETTING STARTED
Packing Checklist
Carefully unpack the projector and check that the following items are included:
DLP PROJECTOR
REMOTE CONTROL
(BATTERIES NOT INCLUDED)
VGA CABLE
CD-ROM
(THIS USER’S MANUAL)
POWER CORD
(VARIES PER COUNTRY)
REGISTRATION CARD
QUICK START GUIDE
WARRANTY BOOKLET
Safe
ty Bo
ok
let
SAFETY BOOKLET
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It
is recommend that you keep the original packing material should you ever need to return the equipment
for warranty service.
–1–
User’s Manual
Views of Projector Parts
Front-angled View
ITEM
LABEL
DESCRIPTION
SEE PAGE:
7
1.
IR receiver
Receives the IR signals from the remote control
2.
Lens
Projection Lens
3.
Focus ring
Focuses the projected image
4.
Zoom ring
Enlarges the projected image
5.
Elevator foot
Adjusts level of projector
6.
Function keys
See Top view—On-screen Display (OSD) buttons.
7.
Lamp cover
Remove cover to replace lamp
39
8.
Vertical lens shift
Adjusts the image position vertically
15
9.
Horizontal lens shift
Adjusts the image position horizontally
16
10.
Lens release button
Press the release button before attempting to
replace the lens
10
17
–2–
14
3
IN5316HD/IN5318 – User’s Manual
Top view—On-screen Display (OSD) buttons
ITEM
LABEL
DESCRIPTION
1.
MENU
Open and exit OSD menus
2.
◄ (Left cursor)
3.
▲ (Up cursor)
4.
▼ (Down cursor)
5.
► (Right cursor)
Navigate and change settings in the OSD
Quick Menu – For Volume
Navigate the OSD
Quick Menu – For Keystone
Navigate the OSD
Quick Menu – For Keystone
Navigate and change settings in the OSD
Quick Menu – For Volume
6.
SELECT
Enter or confirm highlighted OSD menu item
–3–
SEE PAGE:
19
User’s Manual
Rear view
1 2
3
17 18
19
4
5 6
20
21 22 24 25 26
23
7
8
9
10
11
12
13
14
15
16
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
DC 12V TRIGGER
Connect a 12V screen trigger (200ma max)
2.
AUDIO OUT
Connect an AUDIO CABLE to an external speaker system
3.
AUDIO3 (L and R)
Connect the AUDIO CABLE from an input device
4.
VIDEO
Connect the COMPOSITE CABLE from a video device
5.
S-VIDEO
Connect the S-VIDEO CABLE from a video device
6.
YPbPr
Connect the COMPONENT CABLE from a component video enabled
device
7.
BNC
Connect the BNC CABLES from a computer or a video enabled device
8.
AC IN
Connect the POWER CABLE
9.
Power Switch
Connects AC power to the projector
10.
Safety Cable Anchor
Secure a ceiling mount safety cable to this anchor
11.
Security Lock
Connect a security lock system to the projector and attach to a permanent object
12.
AUDIO 2 (L and R)
Connect the AUDIO CABLES from an input device
13.
SERIAL
Connect an RS-232 serial port cable for command control
14.
IR receiver
Receives the remote control IR signal
15.
AUDIO 1
Connect the AUDIO CABLE from an input device
16.
VGA OUT
Connect the RGB cable to a display (Pass through by VGA1 only)
12
–4–
7
IN5316HD/IN5318 – User’s Manual
17.
USB
Connect the USB CABLE from a computer
(used for presentation slide control with the projector remote)
18.
DISPLAYPORT
Connect a DISPLAYPORT CABLE to a DISPLAYPORT source
19.
HDMI
Connect the HDMI CABLE from an HDMI device
20.
VGA2
Connect the RGB CABLE from a computer or a video enabled device
21.
RJ45
Connect a LAN CABLE for networking purposes
22.
READY LED
23.
TEMP LED
24.
PWR LED
Solid Red
Normal operation
Flashing Red
Lamp is not ready
Solid Red
Overheating
Solid Red
Standby
Solid Green
Normal operation
Flashing
Green or
Red
LED error messages
44
25.
POWER button
Turns the projector on or off (main power switch must
be turned on first).
26.
VGA1
Connect the RGB CABLE from a computer or a video enabled device
12
Note:
If your video equipment has various input sources, it is recommended to connect in priority of
HDMI, component, S-Video, Composite for better picture quality.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
–5–
User’s Manual
Bottom view
ITEM
LABEL
DESCRIPTION
SEE PAGE:
1.
Leveling/Elevator Feet
Raise and rotate the feet to change and fine tune
the angle of the projector.
2.
Ceiling support holes
Only use with an InFocus ceiling mount system (p/n PRJ-MNT-UNIV).
See your InFocus dealer or go to www.infocusstore.com.
14
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 6 mm (0.23 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment over a period of 60 seconds.
–6–
IN5316HD/IN5318 – User’s Manual
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
–7–
User’s Manual
ITEM
1.
2.
3.
4.
LABEL
DESCRIPTION
SEE PAGE:
12
Power ON
Turn the projector on
LED indicator
Only lights when the remote keys are pressed
Display Mode
Choose a suitable preset mode for usage environment
Contrast
Display the Contrast setting bar and use the right and left keys to adjust
5.
Brightness
Display the Brightness setting bar and use the right and left keys to adjust.
6.
Left cursor
When the OSD is displayed, this button navigates to the
left. When USB has been connected to the projector
and PC, the previous presentation slide is displayed
7.
8.
9.
10.
11.
12.
13.
Menu
Display the OSD menu
Auto image
Re-synchronize the PC image
Overscan
Adjust overscan
Source-1
VGA 1
Source-4
DISPLAYPORT
Source-7
S-Video
Power OFF
Turn the projector off
14.
Source
Display the source menu
15.
16.
Info
Display projector information
Mute
Mute the audio
17.
Up cursor /
Keystone+
When the OSD is displayed, this button navigates up the
menu. Otherwise it adjusts keystone
18.
Select
Enter and confirm settings in the OSD
19.
Right cursor
When the OSD is displayed, this button navigates to the
right. When USB has been connected to the projector
and PC, the next presentation slide is displayed
20.
Down cursor /
Keystone -
When the OSD is displayed, this button navigates down
the menu. Otherwise it adjusts keystone
Resize
Change the image aspect ratio
Blank
Blank the screen
Volume+
Increase the volume
Freeze
Freeze video
Volume-
Decrease the volume
Source-3
HDMI
Source-2
VGA 2
Source-6
Component
Source-5
RGBHV
Light
Turn the remote control backlight on or off
Source-8
Composite
21.
22.
23.
24.
25.
26.
27.
28.
29.
30.
31.
–8–
19
13
19
IN5316HD/IN5318 – User’s Manual
SETUP AND OPERATION
Inserting the Remote Control Batteries
1.
Remove the battery compartment
cover by sliding the cover in the direction of the arrow.
2.
Insert the batteries (not included) as
shown in the illustration.
3.
Replace the cover.
Caution:
1. Only use AA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
4. Do not mix old and new batteries, or mix battery types.
–9–
User’s Manual
Installing or Removing the Optional Lens
Caution:
y Do not shake or place excessive pressure on the projector or the lens components as the projector and lens components contain precision parts.
y Before removing or installing the lens, be sure to turn off the projector, wait until the cooling fans
stop, and turn off the main power switch.
y Do not touch the lens surface when removing or installing the lens.
y Keep fingerprints, dust or oil off the lens surface.
y Do not scratch the lens surface.
y Work on a level surface with a soft cloth under it to avoid scratching.
y If you remove and store the lens, attach the lens cap to the projector to keep off dust and dirt.
Removing the Existing Lens From the Projector
1.
Push and release the top cover to
open as shown.
2.
Push the LENS RELEASE button to
the unlock position.
3.
Grasp the lens.
4.
Rotate the lens counterclockwise.
The existing lens will be disengaged.
5.
Pull out the existing lens slowly.
IRIS PIN
– 10 –
IN5316HD/IN5318 – User’s Manual
Installing the New Lens
1.
Align the notches and correctly position the electrical contact pad as
shown in the picture.
Note:
Pin of IRIS should be in the direction
as shown in the picture.
2.
Rotate the lens clockwise until you
feel it click into place.
– 11 –
User’s Manual
Starting and Shutting down the Projector
1.
Remove the lens cap.
2.
Connect the power cord to the projector. Connect the other end to a
wall outlet. Verify that the AC Power
switch on the back of the unit is
turned on. When connected, the
PWR LED will turn solid Red.
3.
Turn on the lamp by pressing the
“
” button on the rear of the
projector or the Power On button on
the remote.
The PWR LED will now solid Green.
The startup screen will display in
approximately 30 seconds.
– 12 –
IN5316HD/IN5318 – User’s Manual
4.
If more than one input device is connected, press the SOURCE button and use ▲▼ to
scroll among devices.
•
VGA 1 : Analog RGB
•
VGA 2 : Analog RGB
•
BNC : Analog / serial digital interface video inputs
•
HDMI : High Definition Multimedia Interface (HDMI)
•
DISPLAYPORT : DISPLAYPORT input
•
Component Video: DVD input YCbCr / YPbPr, or HDTV input YPbPr via HD15
connector
5.
•
S-Video: Super video (Y/C separated)
•
Composite Video: Traditional composite video
To turn the projector off, press the
Power OFF button (
). on the
projector keypad or remote. When
the POWER OFF window appears,
press the Power OFF button (
)
again.
The projector turns off.
Caution:
1. Be sure to remove the lens cap before starting projector.
2. Do not unplug the power cord until the READY LED stops flashing–indicating the projector has
cooled down.
– 13 –
User’s Manual
Adjusting the Projector Level
Take note of the following when setting up the projector:
•
The projector table or stand should be level and sturdy.
•
Position the projector so that it is perpendicular to the screen.
•
Remove and discard the foam spacers on the rear leveling feet before adjusting the projection angle.
•
Ensure the cables are in a safe location. You could trip over them.
1.
To raise the level of the projector,
twist the leveling feet clockwise.
2.
To lower the level of the projector,
lift the projector and twist the leveling feet counter clockwise.
– 14 –
IN5316HD/IN5318 – User’s Manual
Adjusting Projected Image Position Using Shift
The Shift feature provides a lens shift function that can be used to adjust the position of the projected
image either horizontally or vertically within the range detailed below.
Shift is a unique system that provides lens shift while maintaining a much higher ANSI contrast ratio
than traditional lens shift systems.
Adjusting the vertical image position
The vertical image height can be adjusted between 10% and -70% offset for IN5316HD (1080P); 5%
and -65% for IN5318 (WUXGA) (offset = (O/H) x100%, O: distance from bottom of image to center of
lens). Note that the maximum vertical image height adjustment can be limited by the horizontal image
position. Offset is the distance between the lens center line and the bottom of the image. The offset is
positive if the lens center line is below the bottom of the image. The offset is negative if the lens center line is above the bottom of the image.. For example it is not possible to achieve the maximum
vertical image position height detailed above if the horizontal image position is at maximum. Please
consult the Shift Range diagram below for further clarification.
For IN5318 (WUXGA)
-70% offset
-50% offset
10%H
10% offset
– 15 –
-65% offset
Screen Height ( H )
Screen Height ( H )
For IN5316HD (1080P)
-50% offset
5%H
5% offset
User’s Manual
Adjusting the horizontal image position
With the lens in the center position the horizontal image position can be adjusted to the left or right by
up to a maximum of 5% of the image width. Note that the maximum horizontal image height adjustment can be limited by the vertical image position. For example it is not possible to achieve the
maximum horizontal image position if the vertical image position is at maximum. Please consult the
Shift Range diagram below for further clarification.
Shift Range Diagram
For IN5316HD (1080P)
Wx5%
Max H image shift=10% offset
Max W image shift=Wx5%
When Wx5%, Max image shift= - 10% offset
When 10% offset, Max image shift=Wx0%
For IN5318 (WUXGA)
W
Wx5%
Wx5%
W
Wx5%
10% offset
5% offset
-10% offset
-15% offset
Max H image shift=5% offset
Max W image shift=Wx5%
When Wx5%, Max image shift= - 15% offset
When 5% offset, Max image shift=Wx0%
– 16 –
IN5316HD/IN5318 – User’s Manual
Adjusting Zoom, Focus and Keystone
1.
Use the Zoom ring to
resize the projected image and screen size.
2.
Use the Focus ring to
sharpen the projected
image.
3.
Use the KEYSTONE
buttons (on the projector or the remote
control) to correct image trapezoiding (wider
top or bottom).
Remote control and OSD panel
4.
The keystone control
appears on the display.
– 17 –
User’s Manual
Adjusting the Volume
1.
Press the Volume buttons (on the projector or
the remote control).
The volume control
appears on the display.
2.
Use the Vol +/- buttons
(on the projector or the
remote control).
3.
Press the MUTE button
to turn off the audio
(This feature is only
available on the remote).
– 18 –
IN5316HD/IN5318 – User’s Manual
ON-SCREEN DISPLAY (OSD) MENU SETTINGS
OSD Menu Controls
The projector has an OSD that lets you make image adjustments and change various settings.
Navigating the OSD
You can use the remote control cursor buttons or the projector keypad to navigate and make changes to
the OSD.
1. To enter the OSD, press the MENU
button.
2. There are six menus. Press the cursor ◄► button to move through the
menus.
3. Press the cursor ▲▼ button to move
up and down in a menu.
4. Press ◄► to change values for settings.
5. Press MENU to access a different
menu, leave a submenu or close the
OSD.
Note:
Depending on the video source, not all items in the OSD are available. For example, the PC Detail
Adjustment item in the Display menu can only be modified when connected to a PC. Items that are
not available cannot be accessed and are grayed out.
– 19 –
User’s Manual
Setting the OSD Language
Set the OSD language to your preference before continuing.
1. Press the MENU button. Press the cursor ◄► button to navigate to SETUP>>Basic.
2. Press the cursor ▲▼ button until Language is highlighted.
3. Press the cursor ◄► button until the language you want is selected.
4. Press the MENU button to close the OSD.
– 20 –
IN5316HD/IN5318 – User’s Manual
OSD Menu Overview
Use the following illustration to quickly find a setting or determine the range for a setting.
– 21 –
User’s Manual
PICTURE>>Basic Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
PICTURE>>Basic menu. Press the cursor ▲▼ button to move up and down in the PICTURE>>Basic
menu. Press ◄► to change values for settings.
Note:
Customizing the settings in PICTURE>>Basic menu is only available in User 1/ 2/ 3 mode.
ITEM
DESCRIPTION
Display Mode
Press the cursor ◄► buttons to set the Display Mode.
(Range: Movie/ Bright/ Normal/ User 1/ User 2/ User 3)
Brightness
Press the cursor ◄► buttons to adjust the display brightness.
Contrast
Press the cursor ◄► buttons to adjust the display contrast.
Color
Press the cursor ◄► buttons to adjust the video saturation.
Notes: This function is only available when Video or S-Video input source is selected.
Tint
Press the cursor ◄► buttons to adjust the video tint/hue.
Notes: This function is only available when Video or S-Video with NTSC
system input source is selected.
Sharpness
Press the cursor ◄► buttons to adjust the display sharpness.
Notes: This function is only available when Video or S-Video input source is selected.
Flesh Tone
Press the cursor ◄► buttons to adjust the display flesh tone.
Notes: This function is only available when Video or S-Video input source is selected.
Reset Picture Settings
Press the ENTER/SELECT button to reset all settings to default values.
– 22 –
IN5316HD/IN5318 – User’s Manual
PICTURE>>Advanced Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
PICTURE>>Advanced menu. Press the cursor ▲▼ button to move up and down in the
PICTURE>>Advanced menu. Press ◄► to change values for settings.
ITEM
DESCRIPTION
Noise Reduction
Press the cursor ◄► button to adjust the Noise Reduction.
Color Temperature
Press the cursor ◄► button to set the Color Temperature.
(Range: Warm/Normal/Cool/Cooler/High Cool)
Gamma
Press the cursor ◄► button to adjust the gamma correction of the display.
Notes: This function is only available in User 1/ 2/ 3 mode.
HSG Adjustment
Press the ENTER/SELECT button to enter the HSG (Hue/Saturation/Gain) Adjustment sub menu.
See HSG Adjustment on page 24.
Color Space
Press the cursor ◄► button to set the Color Space.
(Range: Auto/ RGB/ SDTV/ HDTV)
Notes: This function is only available when HDMI input source is selected.
– 23 –
User’s Manual
HSG Adjustment
Press the ENTER/SELECT button to enter the HSG Adjustment sub menu.
ITEM
DESCRIPTION
Primary Color
Press the ◄► buttons to set the Primary Color.
Notes: There are six colors (R/ G/ B/ C/ M/ Y) to be customized.
Hue
Press the ◄► buttons to adjust the Hue.
Saturation
Press the ◄► buttons to adjust the Saturation.
Gain
Press the ◄► buttons to adjust the Gain.
– 24 –
IN5316HD/IN5318 – User’s Manual
DISPLAY Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the DISPLAY
menu. Press the cursor ▲▼ button to move up and down in the DISPLAY menu.
Press ◄► to change values for settings.
ITEM
DESCRIPTION
Aspect Ratio
Press the cursor ◄► button to set the Aspect Ratio.
(Range: Auto/ 16:10/ 16:9/ 4:3/ Letter Box/ Real)
Keystone
Press the cursor ◄► button to adjust the Keystone.
Notes: This function is available when the Auto Keystone function is turned off.
Overscan
Press the cursor ◄► button to adjust the Overscan.
Digital Zoom
Press the cursor ◄► button to adjust the Digital Zoom.
PC Detail Adjustment
Press the ENTER/SELECT button to enter the PC Detail Adjustment sub menu.
See PC Detail Adjustment on page 26.
– 25 –
User’s Manual
PC Detail Adjustment
Press the ENTER/SELECT button to enter the PC Detail Adjustment sub menu.
Note:
Customizing the settings in PC Detail Adjustment menu is only available when PC input source (analog RGB) is selected.
ITEM
DESCRIPTION
Auto
Press the RE-SYNC button on the projector keypad or the AUTO IMAGE button on
the remote control to automatically adjust frequency, phase, and position.
Frequency
Press the ◄► buttons to adjust the A/D sampling number.
Phase
Press the ◄► buttons to adjust the A/D sampling clock.
Horizontal Position
Press the ◄► buttons to adjust the display position right or left.
Vertical Position
Press the ◄► buttons to adjust the display position up or down.
– 26 –
IN5316HD/IN5318 – User’s Manual
SETUP>>Basic Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
SETUP>>Basic menu. Press the cursor ▲▼ button to move up and down in the
SETUP>>Basic menu. Press ◄► to change values for settings.
ITEM
Language
DESCRIPTION
Press the cursor ◄► buttons to select a different localization menu.
(Range: English/ Français/ Español/ Deutsch/ Português/ 簡体中文/ 繁體中文/
Italiano/ Svenska/ Nederlands/ Suomi/ Dansk/ Norsk/ Polski/ 한국어/ Türkçe/
Русский/ Bahasa Indonesia/)
Splash Logo
Press the cursor ◄► buttons to select a different startup screen.
(Range: InFocus/ Blue/ Black)
Projection
Press the cursor ◄► buttons to choose from four projection methods:
Front Table/ Front Ceiling/ Rear Table/ Rear Ceiling.
Blank Timer
Press the cursor ◄► buttons to set the Blank Screen timer. The projected image is
automatically restored after the set time.
(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Auto Power Off
Press the cursor ◄► buttons to set the Auto Power Off timer. The projector automatically turns off if no input source is detected after the preset period of time.
(Range: Disable/ 5 min/ 10 min/ 15 min/ 20 min/ 25 min/ 30 min)
Sleep Timer
Press the cursor ◄► buttons to set Sleep timer. The projector automatically turns off
after the preset period of time.
(Range: Disable/ 30 min/ 1hr/ 2hr/ 3hr/ 4hr/ 8hr/ 12hr)
Auto Power On
Press the cursor ◄► button to enable or disable Automatic Power On when AC power is
supplied.
Background Color
Press the cursor ◄► buttons to select the background color when no input source is
detected.
(Range: Purple/ Black/ Blue)
Menu Settings
Press the ENTER/SELECT button to enter the Menu Settings sub menu. See Menu
Settings on page 28.
Source
Press the ENTER/SELECT button to enter the Source sub menu. See Source on
page 29.
Lan Control Settings
Press the ENTER/SELECT button to enter the Lan Control Settings sub menu.
See Lan Control Settings on page 30.
– 27 –
User’s Manual
Menu Settings
Press the ENTER/SELECT button to enter the Menu Settings sub menu.
ITEM
DESCRIPTION
Menu Position
Press the ◄► buttons to select from five OSD locations:
Top-Left/ Top-Right/ Center/ Bottom-Left/ Bottom-Right.
Menu Display Time
Press the ◄► buttons to set the Menu Display timer before the OSD times out.
(Range: 5sec/ 10sec/ 15sec/ 20sec/ 25sec/ 30sec)
– 28 –
IN5316HD/IN5318 – User’s Manual
Source
Press the ENTER/SELECT button to enter the Source sub menu.
ITEM
VGA 1
DESCRIPTION
Press the ◄► buttons to enable or disable the VGA source.
VGA 2
HDMI
Press the ◄► buttons to enable or disable the HDMI source.
DisplayPort
Press the ◄► buttons to enable or disable the DisplayPort source.
RGBHV
Press the ◄► buttons to enable or disable the RGBHV source.
Component
Press the ◄► buttons to enable or disable the Component source.
S-Video
Press the ◄► buttons to enable or disable the S-Video source.
Composite
Press the ◄► buttons to enable or disable the Composite source.
Quick Auto Search
Press the ◄► buttons to enable or disable Quick Auto Search for available input
source.
Notes: When the desired source is selected, the Quick Auto Search function will be
turned off.
– 29 –
User’s Manual
Lan Control Settings
Press the ENTER/SELECT button to enter the Lan Control Settings sub menu.
ITEM
DESCRIPTION
Control By
Press the ◄► buttons to select projector remote command control.
(Range: RS232/ RJ45)
Note: this setting changes the standby power:
RS232 <1W (Default)
RJ45 <9W Network State
Press the ENTER/SELECT button to enter the Network State sub menu. See below.
Network State
ITEM
Network State
DESCRIPTION
Displays the network connection status.
Press ◄► to turn DHCP On or Off.
DHCP
Note: If you select DHCP Off, complete the IP Address, Subnet Mask, Gateway, and
DNS fields.
Projector IP Address
Enter a valid IP address if DHCP is turned off.
Subnet Mask
Enter a valid Subnet Mask if DHCP is turned off.
Default Gateway
Enter the default Gateway address on the network.
DNS
Enter a valid DNS name if DHCP is turned off.
Apply
Press
(ENTER/SELECT) / ► to confirm settings.
– 30 –
IN5316HD/IN5318 – User’s Manual
For simplicity and ease of operation, the projector provides diverse networking and remote management features.
The LAN/RJ45 feature allows the projector to be connected to a network and remotely managed. Available
remote management controls include: Power On/Off, Video-Source, Brightness and Contrast settings, SoundMute, etc.
Enter the Projector IP address shown in the SETUP >> Basic >> Lan Control Setting >> Network
State menu. Note: DHCP must be on. The LAN/RJ45 Web Control window displays as follows:
– 31 –
User’s Manual
Preparing Email Alerts
1. Make sure that user can access the homepage of LAN RJ45 function by web browser (for example, Microsoft Internet Explorer v6.01/v8.0).
2. From the Homepage of LAN/RJ45, click Alert Mail Settings.
3. By default, the input boxes in Alert Mail Settings are blank.
4. To setup email alerts, input the following:
The SMTP field is the mail server for sending out email (SMTP protocol).
This is a required field.
The To field is the recipient’s email address (for example, the projector administrator). This
is a required field.
The Cc field sends a carbon copy of the alert to the specified email address.
– 32 –
IN5316HD/IN5318 – User’s Manual
This is an optional field (for example, the projector administrator’s assistant).
The From field is the sender’s email address (for example, the projector administrator). This
is a required field.
Select the alert conditions by checking the desired boxes.
Note: Fill in all fields as specified. Select the desired alert condition and click Submit to conduct an Email Alert Test. A successful test alerts the designated email accounts. To create
an email alert, you must select alert conditions and enter a correct email address.
Group and Name identify the alerting projector and are located at the button of the alert mail as shown below:
– 33 –
User’s Manual
SETUP>>Advanced Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
SETUP>>Advanced menu. Press the cursor ▲▼ button to move up and down in the
SETUP>>Advanced menu.
ITEM
DESCRIPTION
Audio
Press the ENTER/SELECT button to enter the Audio sub menu. See Audio on page
35.
Lamp
Press the ENTER/SELECT button to enter the Lamp sub menu. See Lamp on page
35.
HDMI
Press the ENTER/SELECT button to enter the HDMI sub menu. See HDMI on page
36.
High Altitude Mode
Press the cursor ◄► buttons to turn on or off High Altitude Mode when the altitude of
the environment is higher than 1500m ( 4921 ft. ).
Test Pattern
Press the cursor ◄► buttons to turn on or off the grid test pattern.
Closed Caption
Press the ENTER/SELECT button to enter the Closed Caption sub menu.
See Closed Caption on page 36.
LED Control
Press the cursor ◄► buttons to turn the projector LED indicators on (Normal) and off
(Off).
Presentation Timer
Press
(ENTER/SELECT) / ► to the Presentation Timer menu. See Presentation
Timer on page 37.
Reset All
Press the ENTER/SELECT button to enter reset all settings to default values.
– 34 –
IN5316HD/IN5318 – User’s Manual
Audio
Press the ENTER/SELECT button to enter the Audio sub menu.
ITEM
DESCRIPTION
Volume
Press the ◄► buttons to adjust the audio Volume.
Treble
Press the ◄► buttons to adjust the audio Treble.
Bass
Press the ◄► buttons to adjust the audio Bass.
Mute
Press the ◄► buttons to turn on or off the internal and external speakers.
AGC
Press the ◄► buttons to turn on or off the Automatic Gain Control setting.
Audio Input
Press the ◄► buttons to select audio input channel
(Range: Audio 1/ Audio 2/ Audio3)
(Range: Audio 1/ Audio 2/ Audio3/HDMI)
Note: Available HDMI source
(Range: Audio 1/ Audio 2/ Audio3/DP)
Note: Available DP source
Reset
Press the ENTER/SELECT button to reset all menu and submenu items back to factory default settings.
– 35 –
User’s Manual
Lamp
Press the ENTER/SELECT button to enter the Lamp sub menu.
ITEM
DESCRIPTION
Lamp Mode
Press the ◄► buttons to adjust lamp brightness.
Reset Lamp Timer
Press the ENTER/SELECT button to reset the Lamp Hour after the lamp is replaced.
Lamp Hour
Displays the number of hours the lamp has been in use.
HDMI
Press the ENTER/SELECT button to enter the HDMI sub menu.
ITEM
DESCRIPTION
HDMI Format
Press the ◄► buttons to select from three HDMI display formats:
Auto/ PC signal/ Video signal.
HDMI Amplifier Gain
Press the ◄► buttons to adjust HDMI Amplifier Gain. Use this feature when using
long HDMI cable runs.
– 36 –
IN5316HD/IN5318 – User’s Manual
Closed Caption
Press the ENTER/SELECT button to enter the Closed Caption sub menu.
ITEM
DESCRIPTION
Closed Caption Enable
Press the ◄► buttons to turn on or off Closed Caption.
Caption Version
Press the ◄► buttons to select the Caption Version.
Presentation Timer
The Presentation Timer function can indicate the presentation time on the screen to help you achieve
better time management when giving presentations.
ITEM
DESCRIPTION
Timer
Press the cursor ◄► button to enable or disable presentation timer.
Timer Period
Press the cursor ◄► button to select timer period (1 ~ 60 minutes)
Timer Reset
Press
(ENTER/SELECT) / ► to reset the timer settings.
– 37 –
User’s Manual
STATUS Menu
Press the MENU button to open the OSD menu. Press the cursor ◄► button to move to the
STATUS Menu.
ITEM
DESCRIPTION
Source
Displays the activated input source.
Resolution
Displays the native resolution of input source.
Lamp Hour
Displays the number of hours the lamp has been in use.
Firmware Version
Displays the firmware version of the projector.
Note:
Status displayed in this menu is for viewing only and cannot be edited.
– 38 –
IN5316HD/IN5318 – User’s Manual
MAINTENANCE AND SECURITY
Replacing the Projection Lamp
The projection lamp should be replaced when it burns out. Be sure to use the InFocus lamp module designed for this projector. You can order new lamps from www.infocusstore.com (in select areas), your
retailer or your dealer. Only genuine InFocus lamps are tested for use in this projector. Use of non InFocus lamps may cause electrical shock and fire, and may void the projector warranty. InFocus is not liable
for the performance, safety or certification of any other lamps.
Warning:
• The projector uses a high-pressure mercury glass lamp. The lamp may fail prematurely, or it
may rupture with a popping sound if jolted, scratched, or handled while hot. The risk of lamp
failure or rupture also increases as the lamp age increases; please replace the lamp when you
see the “Replace Lamp.”
• Do not touch or block the projector lens with any objects as this can damage the projector
lens. Scratches, gouges and other lens damage are not covered by the product warranty.
• Unplug the power cord before replacing the lamp.
• Do not drop the lamp module. The glass may shatter and cause injury.
• Do not touch the glass surface of the lamp module. Fingerprints can obscure projection
sharpness and may cause the glass to shatter.
• Be extremely careful when removing the lamp housing. In the unlikely event that the lamp
ruptures, small glass fragments may be generated. The lamp module is designed to contain
most of these fragments, but use caution when removing it.
• Before replacing a ruptured lamp, clean the lamp compartment and dispose of cleaning materials. Wash hands after lamp replacement.
• When replacing the lamp while the projector is ceiling-mounted, wear protective eye-
wear to prevent eye injury. Hg – Lamp contains mercury. Manage in accordance with
local disposal laws. See www.lamprecycle.org.
• Be sure to turn off and unplug the projector at least 60 minutes before replacing the lamp.
Failure to do so could result in a severe burn.
1.
Switch off the power to the
projector by pressing the
POWER button twice.
2.
Allow the projector to cool
down at least 60 minutes.
3.
Disconnect the power
cord.
– 39 –
User’s Manual
4.
Loosen the captive screw
on the lamp cover.
5.
Pull up and remove the
cover.
6.
Use a screwdriver to remove the two captive
screws from the lamp
module.
7.
Pull out the lamp module.
– 40 –
IN5316HD/IN5318 – User’s Manual
8.
Reverse steps 1 to 7 to
install the new lamp
module.
While installing, align the
lamp module with the
connector and ensure it is
level to avoid damage.
Note:
The lamp module must sit
securely in place and the
lamp connector must be
connected properly before
tightening the screws.
9.
Turn on the projector and reset the lamp after the lamp module is replaced.
Lamp Reset:
a) Press the Menu button and select the SETUP>>Advanced menu.
b) Highlight "Lamp" and press the Enter/Select button to access the Lamp submenu.
c) Select "Reset Lamp Timer" and press Enter/Select.
d) Highlight "Reset" (it will appear blue) and press Enter/Select to reset the lamp
counter to zero.
– 41 –
User’s Manual
Cleaning the Projector
Cleaning the projector to remove dust and grime will help ensure trouble-free operation.
Warning:
1. Be sure to turn off and unplug the projector at least 60 minutes before cleaning. Failure to do so
could result in a severe burn.
2. Use only a dampened cloth when cleaning. Do not allow water to enter the ventilation openings
on the projector.
3. If a little water gets into the projector interior while cleaning, leave unplugged in a well-ventilated
room for several hours before using.
4. If a lot of water gets into the projector interior when cleaning, have the projector serviced.
Cleaning the Lens
You can purchase optic lens cleaner from most camera stores. Refer to the following to clean the projector lens.
1. Apply a little optic lens cleaner to a clean soft cloth. (Do not apply the cleaner directly to the
lens.)
2. Lightly wipe the lens in a circular motion.
Caution:
1. Do not use abrasive cleaners or solvents.
2. To prevent discoloration or fading, avoid getting cleaner on the projector case.
Cleaning the Case
Refer to the following to clean the projector case.
1. Wipe off dust with a clean dampened cloth.
2. Moisten the cloth with warm water and mild detergent, and then wipe the case.
3. Rinse all detergent from the cloth and wipe the projector again.
Caution:
To prevent discoloration or fading of the case, do not use abrasive alcohol-based cleaners.
– 42 –
IN5316HD/IN5318 – User’s Manual
TROUBLESHOOTING
Common Problems and Solutions
These guidelines provide tips to deal with problems you may encounter while using the projector. If
the problem remains unsolved, contact InFocus at www.infocus.com/support.
Often the problem is traced to something as simple as a loose connection. Check the following before
proceeding to problem-specific solutions.
•
Use another electrical device to confirm that the electrical outlet is working.
•
Ensure the projector is turned on.
•
Ensure all connections are securely attached.
•
Ensure the attached device is turned on.
•
Ensure a connected PC is not in standby mode.
•
Ensure a connected notebook computer is configured for an external display.
(This is usually done by pressing a Fn-key combination on the notebook. Go to
www.infocus.com/support and the Learn tab to review the Laptop Activation chart.)
Tips for Troubleshooting
In each problem-specific section, try the steps in the order suggested. This may help you to solve the
problem more quickly.
Try to pinpoint the problem and avoid replacing non-defective parts.
For example, if you replace batteries and the problem remains, put the original batteries back and go
to the next step.
Keep a record of the steps you take when troubleshooting. The information may be useful when calling Technical Support and obtaining service.
– 43 –
User’s Manual
LED Error Messages
PWR LED
ERROR CODE MESSAGES
READY LED
TEMP LED
Green
Red
Red
Red
Standby
—
ON
—
—
Start-up/Cool Down
ON
—
flashing
—
Overheating
—
—
—
ON
Thermal Break Sensor error
—
7 blinks
—
—
Lamp Error
5 blinks
—
—
—
Burner Fan error
6 blinks
—
1 blinks
—
System Fan error
6 blinks
—
2 blinks
—
Power and Ballast Fan error
6 blinks
—
3 blinks
—
Case Open
—
7 blinks
—
—
DMD error
8 blinks
—
—
—
Color wheel error
9 blinks
—
—
—
In the event of an error, please disconnect the AC power cord and wait for one (1) minute before restarting the projector. If the PWR or READY LED is still blinking or the TEMP LED is lit, contact
InFocus Technical Support at www.infocus.com/support.
Image Problems
Problem: No image appears on the screen
1. Verify the settings on your notebook or desktop PC.
2. Turn off all equipment and power up again in the correct order.
3. Many laptops do not automatically turn on their external video port when a projector is
connected. Usually a key combination like FN + F8 or CRT/LCD key turns the external
display on and off. Locate a function key labeled CRT/LCD or function key with a monitor
symbol. Press FN and the labeled function key simultaneously.
Problem: The image is blurred
1. Adjust the Focus on the projector.
2. Press the Auto Image button on the remote control.
3. Ensure the projector-to-screen distance is within the projection range. (Within 7m/23' for
the standard lens; within 20m/66' for the long lens and within 3m/10' for the short lens).
4. Check that the projector lens is clean.
Problem: The image is wider at the top or bottom (trapezoid effect)
1. Position the projector so it is as perpendicular to the screen as possible.
2. Use the Keystone buttons on the remote control or projector to correct the problem.
Problem: The image is reversed
Check the Projection setting on the Image menu of the OSD.
Problem: The image is streaked
1. Adjust the Frequency and Phase settings in the Display >> PC Detail Adjustment menu..
2. To ensure the problem is not caused by a connected PC’s video card, connect to another
computer.
– 44 –
IN5316HD/IN5318 – User’s Manual
Problem: The image is flat with no contrast
Adjust the Contrast setting in the PICTURE >> Basic menu of the OSD.
Problem: The color of the projected image does not match the source image.
Adjust the Color Temperature and Gamma settings on the PICTURE >> Advanced menu of
the OSD.
Lamp Problems
Problem: There is no light from the projector
1. Check that the power cable is securely connected.
2. Ensure the power source is good by testing with another electrical device.
3. Restart the projector in the correct order and check that the PWR LED is solid Green.
4. If you have replaced the lamp recently, try resetting the lamp connections.
5. Replace the lamp module.
6. Put the old lamp back in the projector and have the projector serviced.
Problem: The lamp goes off
1. Power surges can cause the lamp to turn off. Unplug and re-plug the power cord and
press the Power button.
2. If the lamp still does not ignite, unplug the projector and allow it to cool for 60 minutes.
Replace the lamp.
3. If a new lamp does not resolve the issue, put the old lamp back into the projector and arrange to have the projector repaired.
Remote Control Problems
Problem: The projector does not respond to the remote control
1. Direct the remote control towards remote sensor on the projector.
2. Ensure the path between remote and sensor is not obstructed.
3. Turn off any fluorescent lights in the room.
4. Check the battery polarity.
5. Replace the batteries.
6. Turn off other infrared-enabled devices in the vicinity.
7. Replace the remote control.
– 45 –
User’s Manual
Audio Problems
Problem: There is no sound
1. Adjust the volume on the remote control.
2. Adjust the volume of the audio source.
3. Check the audio cable connection.
4. Disconnect audio out cable.
5. Test the source audio output with other speakers.
6. Have the projector serviced.
Problem: The sound is distorted
1. Check the audio cable connection.
2. Test the source audio output with other speakers.
3. Have the projector serviced.
Having the Projector Serviced
If you are unable to solve the problem contact InFocus Technical Support at www.infocus.com/support. If
your projector needs repair, pack the projector in the original carton and include the return authorization
number on the outside of the box.
– 46 –
IN5316HD/IN5318 – User’s Manual
HDMI Q & A
Q. What is the difference between a “Standard” HDMI cable and a “High-Speed” HDMI
cable?
Recently, HDMI Licensing, LLC announced that cables would be tested as Standard or HighSpeed cables.
˙Standard (or “category 1”) HDMI cables have been tested to perform at speeds of 75Mhz or
up to 2.25Gbps, which is the equivalent of a 720p/1080i signal.
˙High Speed (or “category 2”) HDMI cables have been tested to perform at speeds of 340Mhz
or up to 10.2Gbps, which is the highest bandwidth currently available over an HDMI cable and
can successfully handle 1080p signals including those at increased color depths and/or
increased refresh rates from the Source. High-Speed cables are also able to accommodate
higher resolution displays, such as WQXGA cinema monitors (resolution of 2560 x 1600).
Q. How do I run HDMI cables longer than 10 meters?
There are many HDMI Adopters working on HDMI solutions that extend a cable’s effective
distance from the typical 10 meter range to much longer lengths. These companies
manufacture a variety of solutions that include active cables (active electronics built into
cables that boost and extend the cable’s signal), repeaters, amplifiers as well as CAT5/6 and
fiber solutions.
Q. How can I tell if a cable is an HDMI certified cable?
All HDMI products are required to be certified by the manufacturer as part of the HDMI
Compliance Test Specification. However, there may be instances where cables bearing the
HDMI logo are available but have not been properly tested. HDMI Licensing, LLC actively
investigates these instances to ensure that the HDMI trademark is properly used in the
market. We recommend that consumers buy their cables from a reputable source and a
company that is trusted.
For more detailed information, go to: http://www.hdmi.org/learningcenter/faq.aspx#49
– 47 –
User’s Manual
SPECIFICATIONS
Specifications
Model
Display type
Native Resolution
Projection distance
(standard lens)
Projection screen size
(standard lens)
Projection lens
Zoom ratio (standard lens)
Vertical keystone correction
Projection methods
IN5316HD
IN5318
TI DMD 1080P 0.65”
TI DMD WUXGA 0.67”
1920x1080
1920x1200
1.5 meters ~ 7 meters ( 4.92 ft ~ 22.97 ft )
35.1”~205” (89cm~521cm)
36.1”~211”(92cm~536cm)
Manual Focus/Manual Zoom
1.25
+/- 15 degrees
Front, Rear, Desktop/Ceiling (Rear, Front)
Data compatibility
VGA, SVGA, XGA, SXGA, SXGA+, UXGA, 1080P, WUXGA, Mac
SDTV/ EDTV/ HDTV
480i, 480p,576i, 576p, 720p, 1080i, 1080p
Video compatibility
NTSC 4.43, PAL (M/N/60), SECAM
H-Sync
15K, 31 – 90 KHz
V-Sync
23 – 85 Hz
Safety certification
FCC-B, UL, cUL, CB, CE, CCC, PCT, PSB, SABS, NOM, CECP, SASO,
TUV-GS, KC, UL-S for Argentina and C-TICK
Operation temperature
5° ~ 35°C ( 41° ~ 95°F)
Dimensions (W x D x H)
430.16mm x 318.00mm x 175.00mm (16.94” x 12.52” x 6.89”)
AC Input
Power consumption
Standby
Lamp
AC Universal 100-240, Typical @ 110VAC (100-240)/ ± 10%
Bright mode: 410W / Normal mode: 350W
RS232 Control Enabled <1 watt (Default)
RJ45 Control Enabled <9 watts
Bright mode: 330W / Normal mode: 280W
AMP 3W speaker x 2
Audio speaker
VGA x 2
DISPLAYPORT x 1
S-Video x 1
5 BNC (RGBHV) x 1
Component x 1
Composite video x 1
HDMI x 1
RCA stereo x 2
Mini-jack stereo x 1
VGA x 1
Mini-jack stereo x 1
Input Terminals
Output Terminals
Control Terminals
RS-232C
RJ45
Screen trigger: DC Jack x 1 (DC12V 200mA output function)
USB (Slide Advance, Mouse Clicks and Firmware Updates)
Security cable lock slot
Security
– 48 –
IN5316HD/IN5318 – User’s Manual
A
Image Height
Projection Distance vs. Projection Size (1080P)
Projection Distance
Projection Distance and Size Table
Standard projection lens: TR: 1.54– 1.93; offset=10%
IN5316HD
Distance (m/inch)
Diagonal (inch/ft)
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
TELE
1.71/
67.3
40/3.3
498/
19.6
886/
34.9
50/2
3.42/
134.6
80/6.7
996/
39.2
1771/
69.7
100/3.9
WIDE
4.27/
168.2
100/8.3
1245/
49
2214/
87.2
125/4.9
8.55/
336.4
200/16.7
2491/
98.1
4428/
174.3
249/9.8
1.70/
67.1
50/4.2
623/
24.5
1107/
43.6
62/2.5
3.41/
134.2
100/8.3
1245/
49
2214/
87.2
125/4.9
6.82/
268.4
200/16.7
2491/
98.1
4428/
174.3
249/9.8
10.23/
402.7
300/25
3736/
147.1
6641/
261.5
374/14.7
Long throw projection lens: TR: 1.93– 2.9; offset=10%
IN5316HD
Distance (m/inch)
Diagonal
(inch/ft)
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
TELE
2.57/
101.1
40/
3.3
498/
19.6
886/
34.9
50/2
6.42/
252.8
100/
8.3
1245
/49
2214/
87.2
125/4.9
WIDE
12.84/
505.5
200/
16.7
2491/
98.1
4428/
174.3
249/9.8
19.26/
758.3
300/
25
3736/
147.1
6641/
261.5
374/14.7
2.14/
84.1
50/
4.2
623/
24.5
1107
/43.6
62/2.5
Short throw projection lens: TR: 0.77; offset=10%
IN5316HD
Distance (m/inch)
Diagonal (inch/ft)
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
FIX
0.68/26.8
1.36/53.7
1.70/67.1
2.56/100.7
40/3.3
498/
19.6
886/
34.9
50/2
80/6.7
996/
39.2
1771/
69.7
100/3.9
100/8.3
1245/
49
2214/
87.2
125/4.9
150/12.5
1868/
73.5
3321/
130.7
187/7.4
– 49 –
6.41/
252.3
150/
12.5
1868/
73.5
3321/
130.7
187/7.4
12.82/
504.6
300/
25
3736/
147.1
6641/
261.5
374/14.7
19.23/
757
450/
37.5
5604/
220.6
9962/
392.2
560/22.1
User’s Manual
A
Image Height
Projection Distance vs. Projection Size (WUXGA)
Projection Distance
Projection Distance and Size Table
Standard projection lens: TR: 1.54–1.93; offset=5%
IN5318
TELE
WIDE
Distance (m/inch)
1.66/65.5
3.33/130.9
4.16/163.7
8.31/327.3
1.66/65.3
3.32/130.6
6.63/261.2
9.95/391.8
Diagonal (inch/ft)
40/3.3
80/6.7
100/8.3
200/16.7
50/4.2
100/8.3
200/16.7
300/25
538/21.2
1077/42.4
1346/53
2692/106
673/26.5
1346/53
2692/106
4039/159
862/33.9
1723/67.8
2154/84.8
2154/84.8
4308/169.6
6462/254.4
27/1.1
54/2.1
67/2.6
67/2.6
135/5.3
202/7.9
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
4308/169.6 1077/42.4
135/5.3
34/1.3
Long throw projection lens: TR: 1.93 – 2.9; offset=5%
IN5318
Distance (m/inch)
Diagonal
(inch/ft)
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
TELE
WIDE
2.5/98.4
6.25/245.9
12.49/491.8
18.74/737.8
2.08/81.8
6.24/245.5
12.47/491
18.71/736.5
40/3.3
100/8.3
200/16.7
300/25
50/4.2
150/12.5
300/25
450/37.5
538/21.2
1346/53
2692/106
4039/159
673/26.5
2019/79.5
4039/159
6058/238.5
862/33.9
2154/84.8
27/1.1
67/2.6
4308/169.6 6462/254.4 1077/42.4
135/5.3
202/7.9
Short throw projection lens: TR: 0.77; offset=5%
IN5318
FIX
Distance (m/inch)
0.66/26.1
1.33/52.2
1.66/65.3
2.49/97.9
Diagonal (inch/ft)
40/3.3
80/6.7
100/8.3
150/12.5
538/21.2
1077/42.4
1346/53
2019/79.5
862/33.9
1723/67.8
2154/84.8
3231/127.2
27/1.1
54/2.1
67/2.6
101/4
Image Height
(mm/inch)
Image Width
(mm/inch)
A (Offset -mm/inch)
– 50 –
34/1.3
3231/127.2 6462/254.4
101/4
202/7.9
9693/381.6
303/11.9
IN5316HD/IN5318 – User’s Manual
Timing Mode Table
The projector can display several resolutions. The following table outlines the resolutions that can be
displayed by the projector.
VGA 1/2
H-SYNC V-SYNC COMPOSITE /
HDMI
DP
/RGBHV
(KHZ)
(HZ)
S-VIDEO
(DIGITAL) (DIGITAL)
(ANALOG)
SIGNAL
RESOLUTION
NTSC
—
15.734
60.0
O
—
—
—
PAL/SECAM
—
15.625
50.0
O
—
—
—
720 x 400
37.9
85.0
—
O
O
O
640 x 480
31.5
60.0
—
O
O
O
640 x 480
37.9
72.8
—
O
O
O
640 x 480
37.5
75.0
—
O
O
O
640 x 480
43.3
85.0
—
O
O
O
800 x 600
35.2
56.3
—
O
O
O
800 x 600
37.9
60.3
—
O
O
O
800 x 600
46.9
75.0
—
O
O
O
800 x 600
48.1
72.2
—
O
O
O
800 x 600
53.7
85.1
—
O
O
O
1024 x 768
48.4
60.0
—
O
O
O
1024 x 768
56.5
70.1
—
O
O
O
1024 x 768
60.0
75.0
—
O
O
O
1024 x 768
68.7
85.0
—
O
O
O
1280 x 800
49.7
59.8
—
O
O
O
1280 x 800
62.8
74.9
—
O
O
O
1280 x 800
71.6
84.8
—
O
O
O
1280 x 1024
64.0
60.0
—
O
O
O
1280 x 1024
80.0
75.0
—
O
O
O
1280 x 1024
91.1
85.0
—
O
O
O
1400 x 1050
65.3
60.0
—
O
O
O
1440 x 900
55.9
60.0
—
O
O
O
1600 x1200
75.0
60
—
O
O
O
1920 x1080
67.2
60
—
O
O
O
1920 x1200[RB]
74.0
60
—
O
O
O
640 x 480
35.0
66.7
—
O
O
O
832 x 624
49.7
74.5
—
O
O
O
1024 x 768
60.2
74.9
—
O
O
O
1152 x 870
68.7
75.1
—
O
O
O
480i
15.734
60.0
—
O
O
O
576i
15.625
50.0
—
O
O
O
576p
31.3
50.0
—
O
O
O
480p
31.5
60.0
—
O
O
O
VESA
Apple
Macintosh
SDTV
EDTV
– 51 –
User’s Manual
SIGNAL
HDTV
RESOLUTION
VGA 1/2
H-SYNC V-SYNC COMPOSITE /
HDMI
DP
/RGBHV
(KHZ)
(HZ)
S-VIDEO
(DIGITAL) (DIGITAL)
(ANALOG)
720p
37.5
50.0
—
O
O
O
720p
45.0
60.0
—
O
O
O
1080i
33.8
60.0
—
O
O
O
1080i
28.1
50.0
—
O
O
O
1080p
27
24.0
—
O
O
O
1080p
28.13
25.0
—
O
O
O
1080p
33.75
30.0
—
O
O
O
1080p
67.5
60.0
—
O
O
O
1080p
56.3
50.0
—
O
O
O
O: Frequency supported
—: Frequency not supported
(*) VGA support EDTV/SDTV/HDTV component with an adapter.
– 52 –
IN5316HD/IN5318 – User’s Manual
Projector Dimensions
– 53 –
User’s Manual
REGULATORY COMPLIANCE
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his/her own expense.
Changes or modifications not expressly approved by the parties responsible for compliance could
void the user’s authority to operate the equipment.
Canada
This class B digital apparatus complies with Canadian ICES-003.
WEEE
NOTE: This product is covered electrical and electronic equipment under the European
Union’s Waste from Electrical and electronic Equipment (“WEEE”) Directive (2002/96/EC).
The WEEE Directive requires that covered equipment be collected and managed separately from typical household waste in all EU member states. Please follow the guidance of
your local environmental authority or ask the shop where you purchased the product for
collection or recycling options.
Safety Certifications
FCC-B, UL, cUL, CB, CE, CCC, PCT, PSB, SABS, NOM, CECP, SASO, Tuv-GS, KC, UL-s for Argentina and C-TICK
– 54 –
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising