TAHI SATINJET SHOWER SYSTEM
INSTALLATION GUIDE
TECHNICAL SPECIFICATIONS
Operating Pressure:
Min 1.5 bar, Max 5 bar.
If supply exceeds 5 bar, a pressure limiting valve must be installed.
Operating Temperature:
Max 70°C
ExPLOdEd dIAgRAM
A
B
C
Overhead shower arm cover
Separate overhead shower cover
Attached overhead shower cover (Discard if installing stand-alone overhead shower)
Rail top bracket cover
Rail top 45° cover
Handset
Hose elbow
Hose
Shelf trays
Shelf
Only included when you purchase footrest option.
Attached footrest cover
Separate footrest cover
Connection bar
½" Backnut
Foam seal
Separate overhead shower spacer
Overhead shower assembly
Rail top bracket
Rail
Handset holder
Rail bottom 45° cover
Rail bottom bracket
Rail bottom bracket cover
Separate footrest spacer
Footrest assembly
1
2
PRE WALL LININg REquIREMENTS
Fastening Zone
-load bearing support required
Elbow height at install
Hole
Ø25mm
Min.
300mm
Floor
Shower Kit
Fastening Zone
-load bearing support required
Standard Rail
Fastening Zone
-load bearing support required
Recommended outlet height
Hole
Ø25mm
Elbow height at install
Floor
Fastening Zone
– load-bearing support required
Fastening Zone
– load-bearing support required
1 2 3
Ensure edge is plumb, mark plumb line to floor and mark screw holes
Set bracket aside, drill clearance into lining then pre-drill support
Seal holes. Drive in screws (and wall plugs where appropriate). Clip on covers
25mm (Max.)
Finished wall lining
Backnut (Supplied)
Connection bar
FLOW
Deeper precision bored end
Overhead outlet 16 ±3mm
Elbow outlet 8.5 ±1.5mm
Ensure the deeper precision bored end connects to the overhead arm of shower. This forms a watertight seal with the ‘O’ ring on the shower arm as per illustration on Page 4. Install backnut and adjust dimension to suit connection type as shown above. Seal the wall lining with silicone sealant
3
Go to 12 on page 6
4 5 6
Fit foam seal around connection bar. Insert waterway and loosely screw nut on to bar
Overhead shower only
Slip top rail bracket under overhead shower bracket
Ensure edge is plumb, mark plumb line to floor and mark screw holes
4
Slip spacer under bracket
Ensure edge of bracket is plumb then mark bottom screw hole
Swing aside. Drill clearance into lining then pre-drill support
7 8 9
Swing aside. Drill clearance into lining then pre-drill support
Seal holes and drive in screws (and wall plugs if appropriate)
Tighten using a lever until bracket is pulled flat against wall
Seal hole and drive in screw (and wall plug if appropriate)
Tighten using a lever until bracket is pulled flat against wall
Run water to ensure the unit is sealed
5
10 11 12
1
2
Run water to ensure the unit is sealed, then clip on covers
Push rail and bottom rail bracket hard on to mounted top bracket
Ensure edge aligns with plumb line.
Mark holes. Set aside, drill clearance into lining and pre-drill support
6
Clip on covers
13 14 15
Go to 19 on page 8
Clip on cover
No footrest
Release lever and slide shelf (if included) and handset holder on to top of rail
Push rail and bracket back on to top bracket and clip on angled cover
Seal holes. To ensure correct alignment, hold rail firmly in place whilst driving screws in (use wall plugs where appropriate). Check alignment with plumb line
Separate footrest
Mark holes
7
16 17 18
Place footrest and mark holes.
Drill clearance in lining and predrill support
Seal holes. Drive in screws
(and wall plugs if appropriate).
Clip on cover with the tab at top as shown
Attach hose & insert trays. Adjust shelf position & handset tension, see overleaf for instructions
8
Set footrest aside, drill clearance into lining then pre-drill support
Seal holes. Attach footrest cap.
Drive in screws (and wall plugs if appropriate). Clip on cover
AdJuSTMENT
Shelf adjustment
UN-LOCK
LOCK
Handset holder tension adjustment
Located at the back of slider
Thumb screw
Adjust the tension on the handset holder by rotating the thumb screw.
CLEANINg
Water contains lime which remains on the surface after the water has evaporated. These lime deposits can be prevented from forming by wiping immediately after use.
To clean the chrome-plated surfaces use a soft cloth, soap and warm water. Never use cleaning agents that contain a corrosive acid or a scouring additive.
Do not use any sharp objects to clean nozzles
Clean filter baskets periodically
Methven warrants this product against manufacturing defects and that it is suitable for use under the operating conditions specified in this instruction sheet.
For your warranty please refer to www.methven.com or call Customer Service
New Zealand
0800 804 222
Australia
1300 638 483
UK
0800 195 1602
290369 Issue B
