MULTIMEDIA PROJECTOR 4K600STZ User`s Manual

MULTIMEDIA PROJECTOR 4K600STZ User`s Manual
Safety Instructions
MULTIMEDIA PROJECTOR
Before Use
Installation Procedure
Basic Guide
User’s Manual
Connection Procedure
Projection Procedure
Convenient Features
Using Menus
Advanced Guide
Menu Configuration
Menu Settings
Using the Projector on a
Network
Advanced Projection
Other Information
Maintenance
Product Specifications
Troubleshooting
ENG
How to Use This Manual
Thank you for purchasing a Canon projector.
The 4K600STZ Multimedia Projector is a high-performance laser projector
capable of projecting high-resolution computer screens and high-quality
digital images on a large screen.
This Manual
This is the user’s manual for the 4K600STZ Multimedia Projector (hereafter,
“projector”). The “Basic Guide” section describes installation and basic use of the
projector. Descriptions of menus and how to connect the projector to a network are
given in the “Advanced Guide” section. Read this manual thoroughly to make the
most of your projector. Installation of the projector should be performed by a
qualified technician, if possible. Contact the Canon Customer Support Center for
further information.
Symbols of Button Operations
The projector can be operated using the buttons on the remote control or on the
side of the projector.
In this document, the button’s operations are shown as below.
Operation of buttons
on side of projector
Remote control button
operation
Indicate the buttons to
be pressed
Symbols Used in This Manual
Sections labeled with these symbols give the following kinds of information.
Indicates precautions and information to note when using the projector.
2
Table of Contents
How to Use This Manual............... 2
Advanced Guide ....................75
Projector Highlights...................... 4
Using Menus ................................76
Safety Instructions........................ 6
Menu Configuration ............................. 76
Safety Symbols in this Manual ........... 12
Basic Menu Operations ....................... 77
Precautions for Use ............................. 13
Menu Configuration ....................80
Installation and Handling
Precautions .......................................... 14
Menu Settings..............................92
Input settings ....................................... 92
Laser Precautions................................ 16
Image adjustment ................................ 97
Precautions for the Batteries of the
Remote Control .................................... 18
Install settings .................................... 106
System settings ................................. 117
For Safe Use ................................ 20
Network settings ................................ 135
Before Installation....................... 21
Wireless LAN (Wi-Fi).......................... 138
Precautions When Carrying/Shipping
the Projector......................................... 21
Completing Projector Settings ......... 140
Checking Projector Information ....... 155
Precautions for Installation................. 21
Using the Projector on a
Network ......................................156
Open Source Software ............... 26
Before Use ................................... 27
Included Accessories .......................... 27
Completing Computer Settings for a
Network Connection .......................... 156
Part Names ........................................... 28
Setting Up the Network ..................... 160
Preparing the Remote Control............ 35
Controlling the Projector from a
Computer ............................................ 181
Basic Guide ............................37
Advanced Projection.................183
Installation Procedure ................ 38
Setting Up the Projector...................... 38
Projecting from Multiple Projectors at
Once (Edge Blending) ....................... 183
Relationship between Image Size and
Projecting Distance ............................. 40
Advanced Registration to Adjust
Projected Images ............................... 187
Lens Shift Function ............................. 42
Adjusting Peripheral Focus .............. 191
Connection Procedure ............... 44
Other Information ................193
Connecting a Computer ...................... 44
Maintenance...............................194
Connecting AV Equipment.................. 45
Cleaning the Projector....................... 194
4K Projection........................................ 46
Plugging the Projector In .................... 51
Replacing the Air Filter...................... 194
Projection Procedure.................. 52
Product Specifications .............197
Step 1 Turn the Projector On .............. 52
Displayed Test Patterns .................... 197
Supported Signal Types .................... 198
Step 2 Select an Input Signal.............. 55
Step 3 Adjust the Image ...................... 57
Specifications..................................... 202
Step 4 Select an Aspect Ratio (Screen
Aspect) Matching the Screen.............. 64
Troubleshooting ........................208
Step 5 Adjusting Keystone
Distortion .............................................. 65
Symptoms and Solutions .................. 209
LED Indicator Details ......................... 208
Index ...........................................214
Step 6 Select the Image Quality (Image
Mode) .................................................... 68
Option.........................................216
Step 7 Turn the Projector Off.............. 71
Convenient Features .................. 72
3
Projector Highlights
4K Model With a High-Definition, 4096 x 2400 LCOS
Panel
Outstanding projection resolution of up to 4096 x 2400 is possible, using three
0.76 inch liquid crystal on silicon (LCOS) panels in conjunction with dual highperformance image processors and a new 4K-compatible wide zoom lens.
Bright Yet Compact, With a Laser Light Source
A bright (6,000 lumen) 4K projector that is also compact, at 559 x 624 x 201 mm
(22.0 x 24.6 x 7.9 in., W x D x H). Features a laser light source that lasts longer
than traditional mercury lamps. (P202)
Supports Fully Digital Input
Compatible with HDMI: 2 (4K / Deep Color / HDCP2.2), the projector enables 4K
projection (up to 4096 x 2160 at 60 Hz) via a single HDMI cable when connected to
equipment such as a Blu-ray player/recorder. 4K projection from multiple input
terminals — two for HDMI and four for DVI — is also supported, using a multi-input
feature. (P47)
Peripheral Focus Adjustment
Image focus can be adjusted on the edges of the screen, enabling use in dome
projection. (P112, P191)
Edge Blending
Blend the overlapping edges of images from multiple projectors to make the overall
image more seamless. (P112)
High-Precision Image Registration
Precise correction of red, green, or blue misalignment in different areas of the
screen is possible by color and area. (P110)
Superior Video Viewing Experience
Refinements in motion blur reduction make video projection more enjoyable to
watch. (P125)
4
Projector Highlights
Fixed Brightness Feature
When the projector is used for a long time, its brightness gradually declines. This
feature pre-sets the brightness of the first use to a lower level, and then
automatically adjusts the output of the light source so that the same brightness
level is maintained. (P111)
Expanded Dynamic Range
Ready for High Dynamic Range (HDR) content, the projector offers an expanded
range of image luminance to preserve detail in highlights and shadows. (P96)
Scheduling
Automate projector tasks according to your schedules. Turn the projector on or off,
switch input signals, and more. (P129)
Wi-Fi Connectivity
In addition to wired LAN connectivity, the projector also supports Wi-Fi.
In Projector Access Point (PJ AP) mode, the projector can be connected to up to
five computers without using a wireless access point.
Quiet Mode
This feature reduces laser output from the light source to less than half and lowers
the speed of the cooling fan to reduce noise. (P104)
5
Safety Instructions
Before installing and operating the projector, read this manual thoroughly.
This projector provides many convenient features and functions. Operating the
projector properly enables you to manage those features and maintain it in good
condition for many years to come.
Improper operation may result in not only shortening the product life, but also
malfunctions, fire hazards, or other accidents.
If your projector does not seem to be operating properly, read this manual again,
check operations and cable connections, and try the solutions in the
“Troubleshooting” section in the back of this manual. If the problem still persists,
contact the Canon Customer Support Center.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
THIS SYMBOL INDICATES THAT DANGEROUS VOLTAGE
CONSTITUTING A RISK OF ELECTRIC SHOCK IS PRESENT
WITHIN THIS UNIT.
THIS SYMBOL INDICATES THAT THERE ARE IMPORTANT
OPERATING AND MAINTENANCE INSTRUCTIONS FOR THIS
UNIT IN THE OWNER’S MANUAL.
CAUTION
Not for use in a computer room as defined in the Standard for the Protection of
Electronic Computer / Data Processing Equipment, ANSI / NFPA 75.
6
Safety Instructions
Safety Precautions
• This projector produces intense light from the projection lens. Do not stare
directly into the lens, otherwise eye damage could result. Be especially careful
that children do not stare directly into the beam.
• Install the projector in a proper position. Otherwise it may result in a fire hazard.
• Allowing the proper amount of space on the top, sides, and rear of the projector
cabinet is critical for proper air circulation and cooling of the unit. The diagrams
shown here indicates the minimum space required. If the projector is to be built
into a compartment or similarly enclosed, these minimum distances must be
maintained.
SIDE and TOP
REAR
At least
50 cm (1.6')
At least
2 cm (0.8")
At least
50 cm (1.6')
At least
At least
50 cm (1.6') 50 cm (1.6')
• Do not cover the ventilation slots on the projector. Heat build-up can reduce the
service life of your projector, and can also be dangerous.
• If the projector is unused for an extended time, unplug the projector from the
power outlet.
• Do not project the same image for a long time.
An afterimage may remain on the LCD panels due to the characteristics of the
panels of the projector.
CAUTION ON HANGING FROM THE
CEILING
When hanging the projector from the ceiling, clean the air intake vents and top of
the projector periodically with a vacuum cleaner. If you leave the projector unclean
for a long time, the cooling fans can be clogged with dust, and it may cause a
breakdown or a disaster.
DO NOT SET THE PROJECTOR IN GREASY, WET, OR SMOKY CONDITIONS
SUCH AS IN A KITCHEN TO PREVENT A BREAKDOWN OR A DISASTER. IF
THE PROJECTOR COMES IN CONTACT WITH OIL OR CHEMICALS, IT MAY
BECOME DETERIORATED.
7
Safety Instructions
WARNING:
• THIS APPARATUS MUST BE GROUNDED.
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
Safety Instructions
■ READ AND KEEP THIS OWNER’S MANUAL FOR LATER
USE.
All the safety and operating instructions should be read before beginning to operate
the product.
Read all of the instructions given here and retain them for later use. Unplug this
projector from the AC power supply before cleaning. Do not use liquid or aerosol
cleaners on the projector. Use a damp cloth for cleaning.
Follow all warnings and instructions marked on the projector.
For added protection of the projector during a lightning storm, or when it is left
unattended or unused for long periods of time, unplug it from the wall outlet. This
will prevent damage due to lightning and power surges.
Do not expose this unit to rain or use near water... for example, in a wet basement,
near a swimming pool, etc...
Do not use attachments not recommended by the manufacturer as they may result
in hazards.
Do not place this projector on an unstable cart, stand, or table. The projector may
fall, causing serious injury to a child or adult, and serious damage to the projector.
Use only with a cart or stand recommended by the manufacturer, or sold with the
projector. Wall or shelf mounting should be carried out in accordance with the
manufacturer’s directions, and should use a mounting kit approved by the
manufacturers.
An appliance and cart combination should be moved with care.
Sudden stops, excessive force, and uneven surfaces may cause
the appliance and cart combination to overturn.
Slots and openings in the rear and front of the cabinet are provided
for ventilation, to insure reliable operation of the equipment and to protect it from
overheating.
The openings should never be covered with cloth or other materials, and the
bottom opening should not be blocked by placing the projector on a bed, sofa, rug,
or other similar surface. This projector should never be placed near or over a
radiator or heat register.
This projector should not be placed in a built-in installation such as a book case
unless proper ventilation is provided.
8
Safety Instructions
Do not install the projector near the ventilation duct of air-conditioning equipment.
This projector should be operated using only the type of power source indicated on
the marking label. If you are not sure of the type of power supplied, contact the
Canon Customer Support Center or local power company.
Do not overload wall outlets and extension cords as this can result in fire or electric
shock. Do not allow anything to rest on the power cord. Do not locate this projector
where the cord may be damaged by people walking on it.
Do not attempt to service this projector yourself as opening or removing covers
may expose you to dangerous voltages or other hazards. Refer all servicing to
qualified service personnel.
Unplug this projector from the wall outlet and refer servicing to qualified service
personnel under the following conditions:
a. When the power cord or plug is damaged or frayed.
b. If liquid has been spilled into the projector.
c. If the projector has been exposed to rain or water.
d. If the projector does not operate normally after following the operating
instructions. Adjust only those controls that are covered in the operating
instructions as improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the projector
to normal operating condition.
e. If the projector has been dropped or the cabinet has been damaged.
f. When the projector exhibits a distinct change in performance-this indicates a
need for servicing.
When replacement parts are required, be sure the service technician uses
replacement parts specified by the manufacturer that have the same characteristics
as the original parts. Unauthorized substitutions may result in fire, electric shock, or
injury.
Upon completion of any service or repairs to this projector, ask the service
technician to perform routine safety checks to determine that the projector is in safe
operating condition.
9
Safety Instructions
Never push objects of any kind into this projector through cabinet slots as they may
touch dangerous voltage points or short out parts that could result in a fire or
electric shock. Never spill liquid of any kind onto the projector.
Safety Instructions
AC Power Cord Requirement
The AC Power Cord supplied with this projector meets the requirements for use in
the country you purchased it.
AC Power Cord for the United States and Canada:
The AC Power Cord used in the United States and Canada is
listed by the Underwriters Laboratories (UL) and certified by
the Canadian Standard Association (CSA).
The AC Power Cord has a grounding-type AC line plug. This is
a safety feature to ensure the plug fits into the power outlet. Do
not try to tamper with this safety feature. Should you be unable
to insert the plug into the outlet, contact your electrician.
Ground
THE SOCKET-OUTLET SHOULD BE INSTALLED NEAR THE EQUIPMENT AND
EASILY ACCESSIBLE.
Only for European Union and EEA (Norway, Iceland and
Liechtenstein)
These symbols indicate that this product is not to be disposed of
with your household waste, according to the WEEE Directive (2012/
19/EU), the Battery Directive (2006/66/EC) and/or national
legislation implementing those Directives.
If a chemical symbol is printed beneath the symbol shown above, in
accordance with the Battery Directive, this indicates that a heavy
metal (Hg = Mercury, Cd = Cadmium, Pb = Lead) is present in this
battery or accumulator at a concentration above an applicable
threshold specified in the Battery Directive.
This product should be handed over to a designated collection point,
e.g., on an authorized one-for-one basis when you buy a new similar
product or to an authorized collection site for recycling waste
electrical and electronic equipment (EEE) and batteries and
accumulators. Improper handling of this type of waste could have a
possible impact on the environment and human health due to
potentially hazardous substances that are generally associated with
EEE. Your cooperation in the correct disposal of this product will
contribute to the effective usage of natural resources.
For more information about the recycling of this product, please
contact your local city office, waste authority, approved scheme or
your household waste disposal service or visit
www.canon-europe.com/weee, or www.canon-europe.com/battery.
10
Safety Instructions
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that
may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct the
interference at his own expense. The cable with a ferrite core provided with the
projector must be used with this equipment in order to comply with Class A of the
FCC Rules. Use of a shielded cable is required to comply with Class A of FCC
Rules. Do not make any changes or modifications to the equipment unless
otherwise specified in the instructions. If such changes or modifications should be
made, you could be required to stop operation of the equipment.
Warning:
This is a class A product. In a domestic environment this product may cause radio
interference in which case the user may be required to take adequate measures.
The cable with a ferrite core provided with the projector must be used with this
equipment in order to comply with Class A .
Use of a shielded cable is required to comply with Class A .
11
Safety Instructions
Federal Communication Commission Notice
Safety Instructions
Safety Symbols in this Manual
This section describes the safety symbols used in this manual. Important projector
safety information is identified by the following symbols. Always observe the safety
information by these symbols.
Denotes the risk of death or serious injury from improper
handling if the information is not observed. To ensure safe use,
always observe this information.
Denotes the risk of injury from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of electric shock from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of burns from improper handling if the
information is not observed. To ensure safe use, always observe
this information.
Denotes the risk of eye injury from laser emission if usage
restrictions are not observed.
Denotes prohibited actions.
Denotes required actions or information that must be observed.
12
Safety Instructions
Precautions for Use
During installation, keep the projector plug easily accessible so that the projector can be
unplugged immediately if necessary, or keep a circuit breaker within reach.
If the following situations occur, turn the power off, remove the power plug from the
power outlet and contact the Canon Customer Support Center. Failure to do so could
cause a fire or result in an electric shock.
•
•
•
•
•
If smoke is emitted
If an unusual smell or noise is emitted
If water or other liquid has entered the projector
If metal or any other foreign material has entered the projector
If the projector is knocked over or dropped and the cabinet is
damaged
Pay attention to the following points for handling the power cord. Failure to do so may
cause a fire or electric shock.
• Do not place any objects on the power cord and do not allow it to
become trapped under the projector.
• Do not cover the power cord with a carpet.
• Do not modify or excessively bend, twist, pull, wind, or bundle the
power cord.
• Keep the power cord away from heaters and other sources of
heat.
• Do not use a damaged power cord. If the power cord is
damaged, purchase a replacement from your dealer.
• The power cord included with this projector is for use exclusively
with this product. Do not use this cord for other products.
13
Safety Instructions
As this section contains important safety-related information, be sure to read the
following carefully beforehand in order to use your projector correctly and safely.
Safety Instructions
Pay attention to the following points regarding the power source, power plug and
handling of the connector. Failure to do so may cause a fire or electric shock.
• Do not use any power source with a voltage other than the voltage
indicated (AC 100–240 V).
• Do not pull the power cord and be sure to hold the power plug or
connector when removing. Incorrect handling may damage the
power cord.
• Do not insert any metal objects into the contact parts of the
power plug or connector.
• Do not remove the power plug or connector with wet hands.
• Insert the power plug and connector securely up to the base.
Additionally, do not use a damaged power plug or an outlet that is
loose.
• Before using an extension cord, check carefully to avoid
exceeding the cord’s rated capacity.
• Periodically inspect the power plug and outlet and remove any
dust or dirt from between the plug and the outlet.
Installation and Handling Precautions
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
• Do not use the projector where it might get wet, such as outdoors
or by bathtubs or showers.
• Do not place containers containing a liquid on top of the
projector.
• Do not touch the projector itself, the power cord, or the cable if
lightening strikes.
• Do not move the projector until you have switched off the power,
removed the power plug from the power outlet and unplugged
any other cables.
• Unplug the projector before cleaning or maintenance.
14
Safety Instructions
• Do not remove the cabinet from the projector or disassemble it. The interior
of the projector contains high-voltage components as well as parts that are
hot. If inspection, maintenance or repair is required, contact the Canon
Customer Support Center.
• Do not disassemble or modify the projector (including consumable parts) or
the remote control.
• Do not look directly into the exhaust vents during use.
• Do not insert any object into vents in the projector, such as the air intake vent
or exhaust vents.
• Do not place a pressurized can in front of the exhaust vents. The pressure of
the contents of the can may increase due to heat from the exhaust vents and
this could result in an explosion.
• When cleaning off dust or dirt from projector parts such as the lens or filter,
never use any spray that is flammable. Internal parts that become hot may
ignite and cause a fire.
• As strong light beams are emitted while the projector is in use, do not look
directly into the projector lens. Doing so could cause an eye injury. Pay
particular attention to prevent small children from doing so.
• Light from the projector is classified as
Risk Group 2 (RG2) according to
IEC 62471-5:2015.
• If children may approach the projector or
touch it, always ensure the projector is used under adult supervision.
• Do not hold or install optical instruments (such as magnifying glasses,
reflectors, or glasses) in the path of light from the projector. If projected light
is refracted or reflected and enters people’s eyes, it may result in eye injury.
• Do not lift the projector alone. Have at least one assistant.
• Do not use the projector on a soft surface such as carpet or sponge mat, etc.
Doing so could cause heat to build up inside the projector and this could
result in a fire.
• When setting the projector on a high surface for projection, be sure the
surface is flat and stable.
• For ceiling mounting precautions, refer to the installation manual included
with the ceiling mount (sold separately).
15
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
Failure to do so may cause a fire, electric shock or personal injury.
Safety Instructions
Laser Precautions
• The projector is designated as a Class 1 laser product according to IEC/
EN 60825-1:2014.
• The equipment is designated as a Class 3R laser product according to IEC/
EN 60825-1:2007.
• Complies with FDA performance standards for laser products except for
deviations pursuant to Laser Notice No. 50, dated June 24, 2007.
• Laser parameters
Wavelength: 450 nm – 460 nm
Maximum power: 144 W
Beam divergence: 2°
• The projector incorporates a laser module. Disassembly or modification is
dangerous and must not be attempted.
• Operate and adjust the projector only as described in this manual. Incorrect
operation or adjustment poses a risk of exposure to potentially hazardous
laser light.
• If children may approach the projector or touch it, always ensure the
projector is used under adult supervision.
• Do not use when damaged. Even if the projector is used as described in this
manual, failure to discontinue use when it is damaged (as indicated by
screen abnormalities) may result in fire, electric shock, or eye injury from
laser light.
• The Laser module is equipped in this product. Use of controls or adjustments
or performance of procedures other than those specified herein may result in
hazardous radiation exposure.
• For assistance when disposing of the projector, contact the Canon Customer
Support Center. Do not disassemble the projector yourself when disposing of
it.
Explanatory and warning labels are located in the following positions on the
projector.
16
Safety Instructions
Safety Instructions
17
Safety Instructions
Precautions for the Batteries of the Remote
Control
Pay attention to the following points regarding handling of batteries. Failing to do so
could result in a fire or personal injury.
• Do not heat, short circuit or disassemble the batteries, or place them in a fire.
• Do not attempt to recharge the batteries that are included with the remote
control.
• Remove the batteries when they are flat or when the remote control will not
be used for a long period of time.
• When replacing the batteries, replace both at the same time. Also, do not
use two batteries of a different type at the same time.
• Insert the batteries with the + and - terminals in the correct directions.
• If any liquid from inside the batteries leaks out and contacts your skin, be
sure to wash the liquid off thoroughly.
18
Safety Instructions
• If the projector will not be used for a long period of time, be sure
to remove the power plug from the power outlet to ensure safety.
Failure to do so presents a risk of fire if dust accumulates on the
plug or outlet.
• Parts of the cabinet around and above the exhaust vents may
become hot during projection. Touching these areas during
operation could cause burns to the hands. Pay particular
attention in preventing young children from touching these parts.
Additionally, do not place any metal objects around or above the
exhaust vents. Due to the heat from the projector, doing so could
cause an accident or personal injury.
• Do not place the projector where it may be exposed to oily smoke
or steam, such as near kitchen counters or humidifiers. Doing so
may cause fire or electric shock.
• Do not place any heavy objects on top of the projector or sit /
stand on it. Pay particular attention to prevent small children from
doing so. The projector may be knocked over and this could
result in damage or a personal injury.
• Do not place the projector on an unstable or slanted surface.
Doing so may cause the projector to fall or be knocked over and
could result in a personal injury.
• Do not place any objects in front of the lens
during projection. Also, do not start projection
with the lens cap on. Doing so could cause a
fire.
• The lens is moved by a motor up, down, left, and right in
response to the lens shift function. Do not touch the lens when it
is moving. There is the risk of injury.
19
Safety Instructions
Pay attention to the following points regarding installation and handling of the projector.
For Safe Use
Pay attention to the following points when carrying or transporting the projector.
• This projector is a precision instrument. Do not knock it over or subject it to
impacts.
• Protection of the projector cannot be guaranteed if used packaging or shockabsorbent materials are reused. Fragments from shock-absorbent material
may also enter the interior of the projector which could cause a malfunction.
• Disconnect the cables connected to the projector. Carrying the projector
while the cables are attached may cause an accident.
• Retract the adjustable feet before moving the projector. Leaving the feet
extended may cause damage.
• Do not touch the lens with bare hands. Any smudges or fingerprints on the
lens may affect image quality.
Pay attention to the following points when installing or using the projector.
• Be careful of condensation.
If the projector is abruptly taken to a warmer location, or if the room
temperature rises abruptly, moisture in the air may condense on the lens and
mirror, causing the image to become blurred.
• Do not install the projector in a location where the temperature is high or low.
Doing so may cause a malfunction. The temperature range for operation and
storage are as follows.
Operating temperature: 0°C to 45°C (32°F to 113°F)
Humidity: up to 85%
Storage temperature: -20°C to 60°C (-4°F to 140°F)
• When using the projector at an altitude of 2,300 m (7,548') or higher:
From the projector menu, set [High altitude] to [On]. (P111)
• Do not install the projector near high-voltage electrical power lines or an
electrical power source.
• Do not block the air intake or exhaust vents. Blocking the vents may trap
heat inside the projector, which may shorten the useful life of optical
components or other parts and damage the projector.
• Install the projector leaving at least 50 cm (1.6') between air intake/exhaust
vents and walls on each side of the projector. Leave a gap of at least 2 cm
(0.8") from the bottom of the projector. There is an air intake underneath the
projector. Failure to leave enough space may trap heat inside the projector
and damage it.
• Do not place any objects on top of the projector that may change shape or
color due to heat.
• Do not install the projector in a location that is damp, or where there is a lot
of dust, oily smoke or tobacco smoke. Doing so could cause contamination
of optical components such as the lens and the mirror and may result in
deterioration of image quality.
20
Before Installation
Note the following precautions when carrying or shipping the projector.
• Disconnect the cables connected to the projector. Carrying the
projector with the cables attached may cause an accident.
• Retract the adjustable feet. Leaving the feet extended when the
projector is moved may cause damage.
• Do not expose the projector to strong impact or vibration.
• The projector is heavy and should not be carried alone. Have at
least one assistant.
Precautions for Installation
Be sure to read “Safety Instructions” and “For Safe Use” (P6 – P20). Also
take the following precautions during installation.
• Do not strike the projector or subject it to impact. Doing so may
cause a malfunction.
• Do not install the projector standing on one side or in other
unsteady positions. The projector may be damaged if it tips
over.
■ Do Not Use in the Following Environments
• Locations with excessive humidity, dust, oily smoke or tobacco
smoke
Adhesion to the lens, mirrors or other optical parts may reduce image
quality.
• Near high-voltage power lines or sources of electrical power
This may cause malfunction.
• On soft surfaces such as carpets or cushioned mats
Heat may build up inside the projector and damage it.
• Locations with excessive temperature or humidity
This may damage the projector. Acceptable ranges for operating and
storage temperature and humidity are as follows.
Operating temperature
0°C (32°F) – 45°C (113°F)
Operating humidity
Up to 85%
21
Storage temperature
-20°C (-4°F) – 60°C (140°F)
Before Installation
Precautions When Carrying/Shipping the
Projector
Before Installation
■ Do Not Touch the Lens with Bare Hands
Do not touch the lens with bare hands. Any smudges or
fingerprints on the lens may affect image quality.
■ Allow a 30 Min. Warm Up before Focus Adjustment (P59), if Possible
Immediately after startup, the heat of the light source may prevent stable focus.
When adjusting focus, it is also helpful to use the test pattern (10) (P116, P197).
■ Install at a Sufficient Distance from Walls and Other Obstructions
If the air intake or exhaust vent is
blocked, heat will accumulate
inside the projector, possibly
resulting in a shortened projector
lifetime or a malfunction.
Similarly, do not install in narrow,
enclosed spaces with poor
ventilation. Install in a wellventilated location. Ensure a
minimum clearance of 50 cm (1.6')
above, on both sides, and behind
the projector, as shown below.
Also ensure a minimum clearance
of 2 cm (0.8") below the projector.
Air intake vent
Exhaust
vent
Air intake vent
At least
50 cm (1.6')
At least
2 cm (0.8")
At least
50 cm (1.6')
At least
50 cm (1.6')
At least
50 cm (1.6')
■ Be Careful of Condensation
If the temperature of the room rises suddenly, moisture in the air may condense on
the projector lens and mirror, causing the image to become blurred. Wait until the
condensation has evaporated for the image projected to return to normal.
■ At Altitudes above 2,300 m (7,545.8'), Adjust the Settings
Projector settings must be adjusted when using the projector at altitudes of 2,300 m
(7,545.8') or higher. Specifically, refer to instructions for [High altitude] (P111) in the
[Install settings] menu.
22
Before Installation
■ When Using Mounted on the Ceiling
■ Installation to Project Up, Down, or at an Angle
• Projection is possible upward, downward, or in a variety of
directions, but do not block the air intake and exhaust vents. In
particular, always ensure a minimum clearance of 2 cm (0.8") from
the air intake vent on the bottom of the projector.
• There are no options for installing the projector other than the
ceiling attachment.
• When mounting the projector on the ceiling, it is more convenient
to install the projector right-side up, with the adjustable feet facing
down.
23
Before Installation
When using the projector mounted on
the ceiling or installed in a high location,
clean around the air intake and exhaust
vents periodically. Dust that
accumulates in intake or exhaust vents
may impair ventilation, raising the
temperature inside and posing a risk of
damage or fire. Use a vacuum cleaner or
similar means to remove dust from the
intake vent and exhaust vent.
Before Installation
■ Precautions for Portrait (Upright) Installation
• Do not block the air intake or exhaust vents. In particular,
because there is an air intake vent on the bottom, always ensure
a minimum clearance of 2 cm (0.8") from the bottom.
• Note that no mounting brackets or similar accessories for
portrait installation are available.
24
Before Installation
Copyright Notice
Ensure Network Security
Take measures to ensure network security. Note that Canon is not liable in any
way for direct or indirect loss from network security incidents, such as
unauthorized access.
Before use, configure projector, computer, and network security settings
appropriately.
• Set up the projector for connections only within your protected network,
behind a firewall or the like, instead of direct Internet connections.
• When using the projector in a wireless network, also configure the Wi-Fi
security settings.
• Change the Wi-Fi security key on a regular basis.
About Trademarks
• Ethernet is a registered trademark of Xerox Corporation.
• Microsoft, Windows, Windows Vista, Windows 7, Windows 8, Windows 8.1
and Windows 10 are registered trademarks or trademarks of Microsoft
Corporation in the United States and / or other countries.
• Mac, Mac OS and Macintosh are trademarks of Apple Inc., registered in the
United States and / or other countries.
• HDMI, the HDMI logo and High-Definition Multimedia Interface are
trademarks or registered trademarks of HDMI Licensing, LLC.
• PJLink is a registered trademark of JBMIA and pending trademark in some
countries.
• PJLink is a registered trademark, or an application has been submitted for
trademark, in Japan, the United States and / or other countries or regions.
• AMX is a trademark of AMX Corporation.
• Crestron®, Crestron RoomView®, and Crestron Connected™ are registered
trademarks of Crestron Electronics, Inc.
• Wi-Fi is a registered trademark of the Wi-Fi Alliance.
• Wi-Fi Certified, WPA, WPA2, and the Wi-Fi Certified logo are used in
reference to methods of configuration developed by the Wi-Fi Alliance.
• All other trademarks are the property of their respective owners.
25
Before Installation
Please note that enlarging or reducing the size of an image for commercial
purposes or public presentation may infringe on the legally protected copyright
or the copyright holder of the original material.
Open Source Software
The product contains Open Source Software modules. For details, see
“ThirdPartySoftware.pdf” (Third-Party Software License) in the
OpenSourceSoftware folder in the LICENSE folder on the Setup CD-ROM. Each
module’s license conditions are also available in the same folder.
■ Software under the GNU General Public License Version 2
Contained programs are free software; you can redistribute them and/or modify
them under the terms of the GNU General Public License attached to each copy of
the program.
Each program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. Please see “NO WARRANTY” and
“NO SUPPORT” stated below. For more detail, please see full text of the GNU
General Public License.
NO WARRANTY
BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE
COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE PROGRAM
“AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR
IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE
ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE PROGRAM
IS WITH YOU. SHOULD THE PROGRAM PROVE DEFECTIVE, YOU ASSUME
THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION.
IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN
WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY
MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS PERMITTED ABOVE, BE
LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR
INABILITY TO USE THE PROGRAM (INCLUDING BUT NOT LIMITED TO LOSS
OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED
BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE
WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
NO SUPPORT
Canon Inc., and all its subsidiaries or its dealers do not make any support service
regarding the source code. Canon Inc., and all its subsidiaries or its dealers shall
not respond to any questions or enquiries, from you or any other customers,
regarding the source code.
26
Before Use
Included Accessories
Before use, make sure the following items are included in the package.
• Batteries for the remote control (AA size x2)
• Remote control (part No.: RS-RC05)
Before Use
• Lens cap
The remote control can also be used
in a wired connection with the
projector. (P36)
• Power cord (1.8 m / 5.9')
For Continental
Europe
• User’s Manual (CD-ROM)
For the U.S.A.
and Canada
• Warranty Card
• Important Information
■ Lens Cap
Always remove the lens cap before
projection. Accidentally leaving the lens
cap on during projection may distort the
lens cap and damage the projector.
Lens cap
27
Before Use
Part Names
Projector
■ Front Side
Terminals and connectors (P32)
LED indicators (P30)
Air intake vent
Air filter (P194)
Do not block the air
intake.
Doing so may cause
a malfunction.
Power cord
connector (P51)
Projection lens
Always remove the
lens cap before
projection.
Failure to do so may
cause a
malfunction.
Anti-theft lock hole
An anti-theft wire cable (not
included) can be connected.
Side control (P29)
Infrared remote receiver (P36)
Adjustable feet (P38)
■ Rear Side
Exhaust vent
Do not block the air
exhaust. Doing so may
cause a malfunction.
Infrared remote receiver (P36)
Security bar
A wire or cable can be attached to deter theft.
An opening of 2 mm (0.078") is provided for threading the wire.
28
Before Use
■ Bottom
Air intake vent
Before Use
Side Control
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(1) POWER button (P52, P71)
Turns the projector on or off.
(4) KEYSTONE button (P65)
Corrects keystone distortion.
(2) INPUT button (P55)
Switches the input signal.
(5) OK button (P78)
Determines the item selected from
the menu.
(3) LENS button (P59)
Each time the button is pressed,
the adjustment window changes,
from focus (P59) to zoom (image
size) (P60) to lens shift (image
position) (P62).
To adjust the image, use the [ ] /
[ ] or [ ] / [ ] buttons.
After the focus adjustment window,
the marginal focus adjustment
window is also displayed for
adjusting focus of image edges
(P191), depending on the [Marginal
focus] setting (P112).
(6) Pointer / VOL buttons (P77)
Up, down, left, or right in menu
navigation or other operations.
Adjust the sound volume.
[ ] VOL– button: Decreases the
volume.
[ ] VOL+ button: Increases the
volume.
(7) MENU button (P76)
Displays a menu on the screen.
29
Before Use
LED Indicators
The projector status is shown by the LED indicators (off / lit / flashing).
• POWER (green) : Illuminated during projection.
Otherwise, flashes in the following
situations.
• As the projector transitions from
standby to projection
• While the light source is off in power
management mode
• STAND BY (red) : Illuminated during standby mode.
Otherwise, flashes in the following
situations.
• As the projector transitions from
projection to standby
• While the light source is off in power
management mode
• WARNING (red) : Lights up or flashes when an error
occurs.
• LIGHT (orange) : Lights up or flashes when a problem
occurs with the light source.
• TEMP (red)
: Lights up or flashes when the internal
temperature is high.
30
Before Use
■ LED Indicator Displays
Projector operating status is indicated by five LEDs, as shown in the following table.
For details on warnings, see “LED Indicator Details” (P208).
: Off
TEMP
(red)
: Lit
: Flashing
Operating status
Projector not plugged in.
In standby mode.
Resuming operation (projection) after
standby.
Cooling down while entering standby
or power management mode from
power on.
Power is on. (Projecting.)
In power management mode, with the
light source off. (Flashes green and
then red.)
Internal temperature is high. (In
standby mode.)
Internal temperature is high. (During
projection)
An error has occurred with the light
source unit.
A temperature error has occurred.
Flashes 3 times: An air filter error has
occurred.
Flashes 4 times: A fan error has
occurred.
Flashes 5 times: A power error has
occurred.
31
Before Use
Example of when the POWER indicator is on;
LED indicator
POWER STAND BY WARNING LIGHT
(green)
(red)
(red)
(orange)
Before Use
Input Terminal
(1)
(2)
(4)
(5)
(3)
(6)
(7)
(8)
(9)
(1) Trigger terminal (TRIGGER) (P192)
Used to trigger operation of a screen or other external device when the
projector is turned on or off.
(2) HDMI terminal (HDMI) (P44, P45)
Receives digital video signals (HDMI).
Carries both video and audio signals across a single cable.
(3) Digital PC / DVI-D terminal (DVI-D) (P44)
Connects the external monitor output from a computer.
Receives digital PC signal (Digital PC).
(4) Service port (CONTROL) (P205)
Used for executing user commands (P206 – P207).
(5) LAN port (P135)
Connects the LAN cable (shielded twisted pair).
Used to connect the projector to a network.
(6) USB port (P134)
Connects a USB flash drive. Used for firmware updates.
(7) AUDIO IN terminal (AUDIO IN) (P44)
Receives audio input. Audio supplied to this terminal is played through the
internal speaker when you select [Audio in] as the source audio terminal for
the selected source video.
(8) AUDIO OUT terminal (AUDIO OUT) (P44, P45)
Outputs the selected audio signal. (Connecting an audio cable to this terminal
mutes the speaker.)
(9) Terminal for wired remote control (REMOTE) (P36)
This terminal is used to connect the remote control using a cable.
32
Before Use
Remote Control
(4) OK button (P78)
Determines the item selected from the
menu.
(11)
(5) ZOOM button (P60)
Adjusts the image size.
[ ] / [ ] buttons:
Increase the image size.
[ ] / [ ] buttons:
Decrease the image size.
(12)
(2)
(3)
(6) FOCUS button (P59)
Adjusts focusing.
[ ] / [ ] buttons:
Moves the focus position further away.
[ ] / [ ] buttons:
Moves the focus position nearer.
By pressing the FOCUS button twice,
you can adjust the focus at image
edges (P191).
[Marginal focus] setting (P112).
(4)
(5)
(6)
(7)
(7) TEST PATTERN button (P116)
Displays the test pattern.
(8) D.ZOOM button
Not used with this product.
(8)
(9) Ch button (P122)
Changes the remote control channel
when the remote control is used via the
infrared transmitter.
(9)
(10)
(10) IMAGE button (P68)
Switches the image mode (image
quality).
(1) POWER button (P52, P71)
Turns the projector on or off.
(11) AUTO PC button
Not used with this product.
(2) ASPECT button (P64, P93)
Changes the aspect ratio mode.
(12) INPUT button (P55)
Switches the input signal.
(3) Pointer buttons (P77)
Selects the upper, lower, left or right
item in the menu.
33
Before Use
(1)
Before Use
(13) Change input buttons
Change the input signal between Digital
PC and HDMI.
ANALOG 1, ANALOG 2 and
COMPONENT are not used with this
product.
(24) Terminal for wired remote
control (P36)
Connects the remote control to the
projector, for remote control operation.
(14) MENU button (P76)
Displays a menu on the screen.
(15) EXIT button (P79)
Cancels functions such as menu
display or test pattern during operation
and returns to the image display.
(13)
(16) SHIFT button (P62)
Shifts the image up, down, left, or right.
[ ] / [ ] / [ ] / [ ] buttons:
Moves the image.
(14)
(15)
(17) KEYSTONE button (P65)
Corrects keystone distortion.
The [Keystone] setting enables both
horizontal/vertical keystone correction
(by adjusting top/bottom/left/right
length) and corner correction.
(16)
(17)
(18) VOL button
Adjusts the sound volume.
[ ] button, [3] button:
Increases the volume.
[ ] button, [6] button:
Decreases the volume.
(18)
(19)
(20)
(21)
(19) MUTE button
Mutes the sound.
(22)
(20) Numerical buttons (P127, P141,
P144)
Enter password and TCP/IP setting
values.
(23)
(21) Fn button
Not used with this product.
(24)
(22) BLANK button (P72)
Temporarily blacks out the image.
(23) FREEZE button (P72)
Freezes the projected image.
34
Before Use
Preparing the Remote Control
■ Installing Remote Control Batteries
1
2
Insert batteries.
Insert 2 new AA
batteries in the
compartment with the
+ and – terminals
positioned correctly.
3
Close the
compartment lid.
Insert the tab into the
remote control notch
(1) and push the
battery cover down
(2).
(1)
(2)
• If buttons on the remote control are inoperative when you attempt to operate the
projector, replace the batteries with new ones.
• Do not drop the remote control or subject it to impact.
• Do not spill any liquids on the remote control. Doing so may cause a malfunction.
Pay attention to the following points when handling the batteries.
Failing to do so could result in a fire or personal injury.
• Do not heat, short circuit or disassemble the batteries, or place
them in a fire.
• Do not attempt to recharge the batteries that are included with the
remote control.
• Remove the batteries when they are flat or when the remote
control will not be used for a long period of time.
• When replacing the batteries, replace both at the same time. Also,
do not use two batteries of a different type at the same time.
• Insert the batteries with the + and - terminals in the correct
directions.
• If any liquid from inside the batteries leaks out and contacts your
skin, be sure to wash the liquid off thoroughly.
35
Before Use
Open the battery
compartment lid.
Raise the battery
cover tab while
pushing it.
Before Use
■ Remote Control Operating Range
The remote control is an infrared type. Point it at the infrared remote receiver on the
front or rear of the projector to operate it.
25°
25°
8 m (26.3')
8 m (26.3')
25°
25°
• Use the remote control within an angle of 25° in any direction from directly in front of the
infrared remote receiver.
• The remote control may be inoperative if there is an obstacle between the remote
control and the projector or the infrared remote receiver on the projector is exposed to
direct sunlight or strong light of lighting equipment.
• When you use 2 or more projectors at the same time, you can change the channel
settings to prevent the 2 remote controls from interfering with each other. (P122)
■ Using the Remote (RS-RC05) in a Wired Connection
The remote control can also be used in a wired connection with the projector.
Use a cable with a ø3.5 mm stereo mini jack (not included).
Remote control
(RS-RC05)
Terminal for wired
remote control
ø3.5 mm stereo mini jack
cable (not included)
• Infrared operations cannot be performed if a cable is connected to the projector or the
remote control.
• Use a cable with a ø3.5 mm stereo mini jack (not included) with a length of 30 m (98.4')
or less.
36
Safety Instructions
Before Use
Basic Guide
Installation Procedure
Basic Guide
Connection Procedure
Projection Procedure
Convenient Features
Using Menus
Advanced Guide
Menu Configuration
Menu Settings
Using the Projector on a
Network
Advanced Projection
Other Information
37
Maintenance
Product Specifications
Troubleshooting
Installation Procedure
Before setting up the projector, be sure to read “Before Installation” (P21).
Setting Up the Projector
■ Positioning the Projector in Front of the Screen
Place the projector in front of the screen.
• To avoid keystone distortion, install the
projector so that it is at right angles to the
screen.
• The screen must not be exposed to direct
sunlight or light from lighting equipment.
In a bright room, it is recommended that
lights be turned off, curtains be drawn,
and other steps taken to make the screen
easier to see.
• Colors may appear distorted when
images are viewed from the side on
some screens. For best results, use a
matte screen with a wide viewing angle.
Screen
Optical axis
■ Floor Installation
To adjust the projection position when the projector is installed on the floor, use the
lens shift function (P42, P62) to adjust the image up / down / left / right.
For information about the relationship between image size and projection distance,
refer to page 40.
Lens shift
38
Installation Procedure
■ Installation on High Surfaces
■ Ceiling Mounting or Rear Projection
You can mount the projector on the ceiling (ceiling mounting) or place it behind the
screen (rear projection) if you use a translucent screen.
Rear projection
Ceiling mounting
When mounting the projector on the ceiling, it is more convenient to install the projector
right-side up, with the adjustable feet facing down.
39
Installation Procedure
The projector may fall
and cause accidents or
injury.
Basic Guide
Using the lens shift function (P42), you can project images toward a lower level.
When setting the projector on a high surface for projection, make sure the surface
is flat and stable, and install the projector right-side up with the adjustable feet
facing down.
Installation Procedure
Relationship between Image Size and
Projecting Distance
Height
The projected image size is determined by the distance between the projector and
screen (projection distance) and the zoom position (check specifications for details
on the range in focus). Refer to the following table and decide the distance between
the projector and screen.
Image Size (diagonal)
Width
Relationship between image size and projecting distance (reference values)
4096 x 2160
Image Size
(Dia.)
Image Size
[cm (in)]
4096 x 2400
Projection
distance [m (feet)]
Width
Height
Wide
limit
40
90
(35.4)
47
(18.5)
0.9
(3.0)
1.2
(3.9)
60
135
(53.1)
71
(28.0)
1.3
(4.3)
80
180
(70.9)
95
(37.4)
100
225
(88.6)
120
Image Size
[cm (in)]
Projection
distance [m (feet)]
Height
Wide
limit
Tele limit
88
(34.6)
51
(20.1)
0.9
(3.0)
1.1
(3.6)
1.8
(5.9)
131
(51.6)
77
(30.3)
1.3
(4.3)
1.7
(5.6)
1.8
(5.9)
2.3
(7.5)
175
(68.9)
103
(40.6)
1.8
(5.9)
2.3
(7.5)
118
(46.5)
2.2
(7.2)
2.9
(9.5)
219
(86.2)
128
(50.4)
2.2
(7.2)
2.8
(9.2)
270
(106.3)
142
(55.9)
2.7
(8.6)
3.5
(11.5)
263
(103.5)
154
(60.6)
2.6
(8.5)
3.4
(11.2)
140
315
(124.0)
166
(65.4)
3.1
(10.2)
4.1
(13.5)
307
(120.9)
180
(70.9)
3.1
(10.2)
4.0
(13.1)
160
359
(141.3)
190
(74.8)
3.6
(11.8)
4.7
(15.4)
351
(138.2)
205
(80.7)
3.5
(11.5)
4.6
(15.1)
180
404
(159.1)
213
(83.9)
4.0
(13.1)
5.3
(17.4)
394
(155.1)
231
(90.9)
3.9
(12.8)
5.1
(16.7)
200
449
(176.8)
237
(93.3)
4.5
(14.8)
5.8
(19.0)
438
(172.4)
257
(101.2)
4.4
(14.4)
5.7
(18.7)
220
494
(194.5)
261
(102.8)
4.9
(16.1)
6.4
(21.0)
482
(189.8)
282
(111.0)
4.8
(15.7)
6.3
(20.7)
240
539
(212.2)
284
(111.8)
5.4
(17.7)
7.0
(23.0)
526
(207.1)
308
(121.3)
5.3
(17.4)
6.8
(22.3)
260
584
(229.9)
308
(121.3)
5.8
(19.0)
7.6
(24.9)
570
(224.4)
334
(131.5)
5.7
(18.7)
7.4
(24.3)
280
629
(247.6)
332
(130.7)
6.3
(20.7)
8.2
(26.9)
614
(241.7)
360
(141.7)
6.1
(20.0)
8.0
(26.2)
Tele limit Width
40
Installation Procedure
4096 x 2160
4096 x 2400
Projection
distance [m (feet)]
Height
Wide
limit
300
674
(265.4)
355
(139.8)
6.7
(22.0)
8.8
(28.9)
350
786
(309.4)
415
(163.4)
7.9
(25.9)
400
899
(353.9)
474
(186.6)
450
1011
(398.0)
500
Projection
distance [m (feet)]
Height
Wide
limit
Tele limit
657
(258.7)
385
(151.9)
6.6
(21.7)
8.5
(27.9)
10.2
(33.5)
767
(302.0)
449
(176.8)
7.7
(25.3)
10.0
(32.8)
9.0
(29.5)
11.7
(38.4)
877
(345.3)
514
(202.4)
8.8
(28.9)
11.4
(37.4)
533
(209.8)
10.1
(33.1)
13.1
(43.0)
986
(388.2)
578
(227.6)
9.9
(32.5)
12.8
(42.0)
1123
(442.1)
592
(233.1)
11.2
(36.7)
14.6
(48.0)
1096
(431.5)
642
(252.8)
11.0
(36.1)
14.2
(46.6)
550
1236
(497.2)
652
(256.7)
12.3
(40.4)
16.1
(52.8)
1205
(474.4)
706
(278.0)
12.0
(39.4)
15.7
(51.5)
600
1348
(530.7)
711
(279.9)
13.5
(44.3)
17.5
(57.4)
1315
(517.7)
770
(303.1)
13.1
(43.0)
17.1
(56.1)
Tele limit Width
41
Installation Procedure
Width
Image Size
[cm (in)]
Basic Guide
Image Size
(Dia.)
Image Size
[cm (in)]
Installation Procedure
Lens Shift Function
You can reposition the image in all directions by pressing the SHIFT button on the
remote control, which moves the lens up, down, left, or right. For instructions, refer
to “Adjusting the Image Position” (P62).
■ Amount of Lens Shift
The amount of lens shift is indicated as a percentage relative to the image height
and width. The lens shift ranges for the projector are as follows.
A (Amount of vertical shift)
±60%
B (Amount of horizontal shift)
±10%
The lens can be shifted up or down and to the left or right. Performance using lens
shift is ensured within the recommended range described below. However,
peripheral dimness or blurriness may occur in the corners outside the last 10% of
the horizontal lens shift range and outside the last 15% of the vertical lens shift
range. In this case, adjust lens shift to within the recommended range.
10%
Recommended lens shift range
A
15%
A
B
A
B
A
Lens shift range
42
Installation Procedure
Maximum vertical (A) and horizontal (B) movement using lens shift
(reference values [cm (in)])
A
28 (11.0)
43 (16.9)
57 (22.4)
71 (28.0)
85 (33.5)
100 (39.4)
114 (44.9)
128 (50.4)
142 (55.9)
156 (116.9)
171 (67.3)
185 (72.4)
199 (78.3)
213 (83.9)
249 (98.0)
284 (111.8)
320 (126.0)
355 (139.8)
391 (153.9)
427 (168.1)
B
9 (3.5)
13 (5.1)
18 (7.1)
22 (8.7)
27 (10.6)
31 (12.2)
36 (14.2)
40 (15.7)
45 (17.7)
49 (19.3)
54 (21.3)
58 (22.8)
63 (24.8)
67 (26.4)
79 (31.1)
90 (35.4)
101 (39.8)
112 (44.1)
124 (48.8)
135 (53.1)
4096 x 2400
A
31 (12.2)
46 (18.1)
62 (24.4)
77 (30.3)
92 (36.2)
108 (42.5)
123 (48.4)
139 (54.7)
154 (60.6)
169 (66.5)
185 (72.8)
200 (78.7)
216 (85.0)
231 (90.9)
270 (106.3)
308 (121.3)
347 (136.6)
385 (151.6)
424 (166.9)
462 (181.9)
B
9 (3.5)
13 (5.1)
18 (7.1)
22 (8.7)
26 (10.2)
31 (12.2)
35 (13.8)
39 (15.4)
44 (17.3)
48 (18.9)
53 (20.9)
57 (22.4)
61 (24.0)
66 (26.0)
77 (30.3)
88 (34.7)
99 (39.0)
110 (43.3)
121 (47.6)
131 (52.6)
• (A) values are the approximate vertical lens shift distance from the central image
position within the supported lens shift range.
• (B) values are the approximate horizontal lens shift distance from the central image
position within the supported lens shift range.
• Watch the projected image as you adjust it using lens shift.
• When the image no longer moves, you have reached the limit of the lens shift range.
43
Installation Procedure
40
60
80
100
120
140
160
180
200
220
240
260
280
300
350
400
450
500
550
600
4096 x 2160
Basic Guide
Image size (Dia.)
Connection Procedure
Before connecting the projector to other equipment, turn off both the projector
and the other equipment.
For instructions on connecting multiple sources of input for 4K projection, refer to “4K
Projection” (P46).
Connecting a Computer
Computer
AUDIO output
terminal
Audio cable
(not included)
Monitor output
terminal
(DVI-D terminal)
HDMI
terminal
HDMI cable
(not included)
DVI-D cable
(not included)
DVI-D terminal
HDMI
terminal
AUDIO OUT
terminal
AUDIO IN terminal
Audio cable
(not included)
Mini jack
Audio cable
(not included)
RCA terminal
Amplified speakers
44
Connection Procedure
Connecting AV Equipment
AV equipment
HDMI terminal
Basic Guide
HDMI
terminal
Trigger
terminal
Connection Procedure
HDMI cable
(not included)
AUDIO OUT
terminal
Audio cable
(not included)
Audio cable
(not included)
Mini jack
Mini jack
Audio cable
(not included)
RCA terminal
Amplified speakers
Screen or other product
compatible with the
trigger terminal
45
Connection Procedure
4K Projection
■ Definition of 4K
Several resolution specifications are described as being 4K, including 3840 x 2160,
3840 x 2400, 4096 x 2160, and 4096 x 2400, as shown in the following comparative
simulation.
1920 x 1080
3840 x 2160
4096 x 2400
The projector supports input signals at resolutions up to the maximum 4K resolution
of 4096 x 2400.
For details, check the table of supported signals. (P198)
■ 4K Digital Signal Compatibility
The projector is equipped with DVI-D and HDMI: 2 (4K / Deep Color / HDCP 2.2*1)
inputs.
DVI-D input is classified as single-link or dual-link, depending on the dot clock.
Projecting resolutions with a dot clock higher than 165 MHz requires a dual-link
plug and cable.
Main DVI-D input resolutions
• 4096 x 2160 (dual-link; vertical frequency: 24 Hz)
Main HDMI 2.0 input resolutions
• 3840 x 2160 (vertical frequency: 60 Hz)
Single-link plug
• 4096 x 2160 (vertical frequency: 60 Hz)
Dual-link plug
Resolution
Frequency
Subsampling
Color depth
HDMI 1.4
(10.2 Gbps bandwidth) x 1
HDMI 2.0*2
(18 Gbps bandwidth) x 1
QFHD (3840 x 2160)
24 Hz
422
444
8 bit 10 bit 8 bit 10 bit
46
60 Hz
422
444
8 bit 10 bit 8 bit 10 bit
Connection Procedure
DCI (4096 x 2160)
24 Hz
422
444
8 bit 10 bit 8 bit 10 bit
60 Hz
422
444
8 bit 10 bit 8 bit 10 bit
■ Multi Input Mode
• DVI-D
Using four DVI-D dual-link cables, you can supply signals up to 4096 x 2400
(vertical frequency: 60 Hz). The signals supplied by the four cables are combined to
form a single image.
Connect workstations by using four dual-link DVI cables
47
Connection Procedure
*1 HDCP, short for High-bandwidth Digital Content Protection, is a form of digital
copy protection that prevents illegal copying of content by encrypting digital
signals carried via HDMI from playback devices such as computers to display
devices such as projectors. HDCP specifications are established and managed
by Digital Content Protection, LLC.
*2 Use an HDMI cable supporting 18 Gbps.
Basic Guide
Resolution
Frequency
Subsampling
Color depth
HDMI 1.4
(10.2 Gbps bandwidth) x 1
HDMI 2.0*2
(18 Gbps bandwidth) x 1
Connection Procedure
• HDMI
Using two HDMI cables, you can project 4096 x 2160 (vertical frequency: 60 Hz)
signals as one image. The signals supplied by the two cables are combined to form
a single image.
Connect desktop computers by using two HDMI cables
• Split-screen or four-quadrant projection is not supported when the projector is
connected to multiple devices.
• A single image cannot be projected by using two HDMI 2.0 cables with 4096 x 2160
signals (vertical frequency: 120 Hz).
48
Connection Procedure
■ Settings for Multi Input Mode
Select how to combine two HDMI inputs or four DVI inputs to form an image. Check
computer video output settings in advance, because you must match the display
layout (whether split-screen display or display in four quadrants).
1
In the [Install settings] menu, select [Professional settings] > [Multi input
mode select].
2
Select the input mode to use.
49
Connection Procedure
For instructions on turning the projector on, see “Step 1 Turn the Projector On”
(P52).
Basic Guide
Multi Input Mode
Specify the type of image (including resolution) supplied to the terminals. Use [Normal] for
most signals. For specific signals, use [Single], [1x2], [2x2], or [1x4] as needed. For
details, check the table of supported signals. (P198)
• [Normal] setting
Supports many typical images, including [Single], [1x2], [2x2], and [1x4].
• [Single] setting
Supports many specialized signals using a single terminal.
• [1x2] setting
Supports many specialized signals using two input terminals.
• [2x2] setting
Supports many specialized signals using four input terminals, for projection in a 2x2
layout.
• [1x4] setting
Supports many specialized signals using four input terminals, for projection side by
side.
Connection Procedure
DVI input mode
Specify the combination of DVI input. Choose from [Normal], [Single],
[DVI 1x2], [DVI 2x2], or [DVI 1x4].
• To use signals not included in [Normal] (P200 – P201) when multi input in the
[Input] menu (P55) is set to [DVI 1x2], [DVI 2x2], or [DVI 1x4], set the DVI
input mode menu to [DVI 1x2], [DVI 2x2], or [DVI 1x4].
• To use signals not included in [Normal] (P199) when single input in the [Input]
menu (P55) is set to [DVI-1], [DVI-2], [DVI-3], or [DVI-4], set the DVI input
mode menu to [Single].
HDMI input mode
Specify the combination of HDMI input. Choose from [Normal], [Single], or
[HDMI 1x2].
• To use signals not included in [Normal] (P199) when multi input in the [Input]
menu (P55) is set to [HDMI 1x2], set the HDMI input mode menu to
[HDMI 1x2].
• To use signals not included in [Normal] (P198) when single input in the [Input]
menu (P55) is set to [HDMI-1] or [HDMI-2], set the HDMI input mode menu to
[Single].
When this setting is set to [Normal], the EDID (unique ID that conveys to computers
the model name and setting values of connected display devices) is a list that
consists of video signals used with one or multiple projector terminals. On the video
output equipment, you can specify video signals for use with a different number of
terminals.
[Multi input mode select] window is displayed automatically if the input terminals do not
match the settings configured by using the INPUT button.
50
Connection Procedure
Plugging the Projector In
Connect the power cord to the projector and plug it in.
Basic Guide
51
Connection Procedure
• Unplug the power cord when the projector is not in use for an extended period.
• [Date and time settings] may be reset if the projector is left unplugged for an extended
period. (P128)
Projection Procedure
Step 1 Turn the Projector On
1
Check the connection between the projector and the computer or AV
equipment. (P44, P45)
For instructions on connecting the power cord, refer to “Plugging the Projector
In” (P51).
2
Press the POWER button.
The [POWER] indicator initially flashes green, after which it remains lit.
Remote control
Projector
The countdown window is displayed for approximately 20 seconds, and then
the projection is started. Press the OK or EXIT button to hide the countdown
window.
• Network functions are not available until about 40 seconds after you plug the projector
in.
• Some noise may appear in the projected image during the first few minutes, until the
image stabilizes.
3
Turn on the computer or AV equipment power.
Images from the computer or AV equipment are now projected.
Changing Operations When Projector is Turned On
You can change operations when the projector is turned on as follows.
• You can turn on the projector by connecting the power cord, without
pressing the POWER button. (P125)
• You can change the countdown window. (P118)
• You can skip the countdown window. (P118)
• For faster startup next time, you can store projector status immediately
before the projector is turned off. (P124)
When the Projector Is Left Idle
If no signal is received, the power management feature automatically turns off
the projector after a certain period of inactivity (by default, 15 minutes). (P124)
52
Projection Procedure
■ When the Language Selection Screen Appears
A screen appears when the projector is turned on for the first time. You can select a
language to be used by the projector for displaying menus and messages in the
window. Select the desired language with the pointer buttons and press the OK
button.
You can change the language from the menu at a later time. (P126)
If the language selection screen is out of focus, adjust the focus. (P59)
Remote control
Projector
Basic Guide
■ When the Password Input Screen Appears
If you have set a password, the password input screen appears. Enter your
password. (P127)
■ When “No signal” Appears
With a notebook computer, the user must turn on the external monitor output. (P54)
Press the INPUT button to select the input signal. (P55)
■ When Notebook Computer Screen Does Not Appear
Set your notebook computer to output signals to an external monitor. For more
details, refer to “Changing Notebook Computer Screen Output” (P54).
■ Adjusting Image
• Set the display resolution of the computer to the highest resolution or the
resolution closest to that setting. (P57)
• Use the ZOOM button on the remote control to resize the projected image. (P60)
• If the image is blurry, use the FOCUS button on the remote control to adjust focus.
(P59)
• If necessary, correct keystone distortion by pressing the KEYSTONE button. (P65)
• Select a screen mode (aspect) according to the aspect ratio of the screen, type of
input image signal etc. (P64)
• Select an image mode depending on the projected image. (P68)
A variety of test patterns (P197) can be projected, which are convenient in image
adjustment.
53
Projection Procedure
An item highlighted in orange will be selected.
Projection Procedure
Changing Notebook Computer Screen Output
For projection from a notebook computer, the computer settings must be adjusted
to switch display output.
This operation is not required for a desktop computer.
■ Turning on External Monitor Output
You can turn on the external monitor output via keyboard operation.
To turn on the external monitor output with most computers, press the function key
([F1] to [F12]) which is marked with the external monitor icon while holding down
the [Fn] key.
While pressing
key
press a key such as
or
.
• The function key you use and the method used to turn on the external monitor output
vary depending on the model. For details, see the manual for your notebook computer.
• With Windows 10, Windows 8.1, Windows 8 or Windows 7, you can turn on image
output by holding down the Windows logo key and pressing the [P] key.
54
Projection Procedure
Step 2 Select an Input Signal
Select the input signal in the [Input] menu when you want to project a digital PC or
AV equipment signal, or to switch between inputs when multiple computers or
multiple sets of AV equipment are connected.
Skip this step if you have not changed the input signal since the last projection.
1
Press the INPUT button to display the window shown below.
Remote control
Projector
Basic Guide
Projection Procedure
The currently active input signal is marked with a green circle and enclosed by
a orange border.
Names of input signals available for projection are displayed in white, and
unavailable signal names are grayed out.
2
Press the [ ] / [ ] buttons to select the input signal.
You can also switch from one DVI-D input source to the next by pressing the
DIGITAL button, or from one HDMI input source to the next by pressing the
HDMI button.
55
Projection Procedure
3
Press the OK button to confirm the input signal type.
For multiple input signals, the projection layout is divided as follows.
The numbers 1, 2, 3, and 4 in squares represent the numbers of input
terminals.
[HDMI 1x2]
1
2
When using
multiple
HDMI inputs
[DVI 1x2]
1
[DVI 2x2]
3
1
3
2
4
[DVI 1x4]
1 2 3 4
When using multiple DVI inputs
• You can also switch to your preferred input signal for projection by pressing buttons on
the remote control to switch input signals (specifically, the DIGITAL or HDMI button).
• Using the projector’s multi-input feature, you can supply a single image via two or four
cables. As sources of input for projection at 4K or other resolutions, choose from [DVI
1x2], [DVI 2x2], [DVI 1x4], or [HDMI 1x2]. (P46)
• Signals you supply for Multi Input mode must meet certain conditions. If the signals do
not meet these requirements, a “ ” icon is displayed.
56
Projection Procedure
Step 3 Adjust the Image
Setting the Display Resolution of the Computer
Based on the maximum resolution of the projector, set the display resolution of the
computer to the resolution closest to the output signal resolution of the projector.
(P198)
1
Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution] in the [Control Panel
Home].
2
Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
3
Click the [OK] button.
■ Windows 8.1 / Windows 8
1
Move the cursor toward the upper or lower right corner to access the
menu.
2
3
Click [Settings], and then click [Control Panel].
4
Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
5
Click the [OK] button.
From [Control Panel Home] - [Appearance and Personalization], select
[Adjust screen resolution].
■ Windows 7
1
Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution].
2
Click the [Resolution] tab, and move the slider to select the resolution
closest to the maximum output signal resolution of the projector.
3
Click the [OK] button.
57
Projection Procedure
■ Windows 10
Basic Guide
Maximum resolution
• 4096 x 2160: When [Panel drive mode] is set to [4096x2160].
• 4096 x 2400: When [Panel drive mode] is set to [4096x2400].
For details on the Panel drive mode, see [Panel drive mode] in [Professional
settings] (P108).
Projection Procedure
■ Windows Vista
1
Open the [Control Panel] from the start menu, then select [Appearance
and Personalization] - [Adjust screen resolution] in the [Control Panel
Home].
2
Select the resolution closest to the maximum output signal resolution of
the projector from the [Resolution] list.
3
Click the [OK] button.
■ Mac OS X
1
2
Open the Apple Menu and select [System Preferences].
3
Select the [Display] tab and select the resolution closest to the maximum
output signal resolution of the projector from the [Resolutions] list.
4
Close the [System Preferences] window.
In the [System Preferences] window, click the [Displays] icon to display
the Display window.
58
Projection Procedure
Focusing, Resizing, or Moving the Image
■ Adjusting Image Focus
To adjust the focus, press the FOCUS button on the remote control or the LENS
button on the projector.
1
Press either the FOCUS button on the remote control or the LENS button
on the projector to display the focus adjustment window.
Remote control
Projector
Basic Guide
Press the pointer buttons to adjust the focus.
Remote control
Projector
To adjust the focus, use the [ ] / [ ] button on the remote control or projector.
3
When the focus is adjusted optimally, press the OK button or the FOCUS
button.
When projecting on curved screens, you can adjust the focus at image edges. Refer to
“Marginal focus” (P112) and “Adjusting Peripheral Focus” (P191).
59
Projection Procedure
2
Projection Procedure
■ Adjusting Image Size
The size of the projected image can be adjusted by pressing the ZOOM button on
the remote control or the LENS button on the projector. Change the projector
installation position if your desired image is too large or too small to adjust it with
the zoom function. (P38)
1
Press the ZOOM button on the remote control to display the zoom
adjustment window.
Remote control
Press the LENS button on the projector repeatedly to switch between windows
for parameters adjusted by controlling the lens.
To access the zoom adjustment window, press the LENS button twice (or three
times if you have set [Marginal focus] to [On]).
Projector
Press twice.
When [Marginal focus]
is set to [On].
When [Marginal
focus] is set to [Off].
60
Projection Procedure
2
Press the pointer buttons to adjust the image size.
Remote control
Projector
Screen
3
When the desired image size is selected, press the OK button or the
ZOOM button.
Basic Guide
To enlarge the image, use the [ ] button on the remote control or projector.
To reduce the image, use the [ ] button on the remote control or projector.
Projection Procedure
61
Projection Procedure
■ Adjusting the Image Position
To adjust the screen position up, down, left, or right, press the SHIFT button on the
remote control or the LENS button on the projector. It can change the projected
screen to the most suitable position by moving the position of the lens up/down/left/
right. (P42)
1
Press the SHIFT button on the remote control to display the lens shift
adjustment window.
Remote control
Press the LENS button on the projector repeatedly to switch between windows
for parameters adjusted by controlling the lens.
To access the lens shift adjustment window, press the LENS button three times
(or four times if you have set [Marginal focus] to [On]).
Projector
Press three times.
When [Marginal focus]
is set to [On].
When [Marginal
focus] is set to [Off].
62
Projection Procedure
2
Press the pointer buttons to adjust.
Remote control
Projector
Screen
When the desired position is reached, press the OK button.
Resetting the Position
The lens position after movement with the lens shift function is not returned when
the power is turned off. To return it to its original position, perform reset.
During screen position adjustment, press and hold the SHIFT button on the remote
control or the LENS button on the projector to display the [Lens shift reset] window.
Three options are available: +50%, -50%, 0% (home position). Use the pointer
buttons to select an option, and then press the OK button.
• The lens position may be reset slightly misaligned from the position you chose (+50%,
-50%, 0% (home position)).
• For precise positioning, use the lens shift function to fine-tune the position.
63
Projection Procedure
3
Basic Guide
To raise or lower the image, use the [ ] / [ ] buttons on the remote control or
projector.
To move the image left or right, use the [ ] / [ ] buttons on the remote control
or projector.
To continue moving the image in a specific direction, hold down the
corresponding button.
Projection Procedure
Step 4 Select an Aspect Ratio (Screen Aspect)
Matching the Screen
Select an optimum screen mode (aspect) according to the aspect ratio of the
screen, type of input image signal and so on for the projection to make best use of
the screen size.
Select the Aspect
Select [Aspect] based on the input signal type, aspect ratio of the screen and
resolution.
Types of Aspect Ratios
■ Auto
An image is projected as large as possible at the aspect ratio of the input signal.
Select this mode for normal image projection.
■ True size
The image is projected with the original resolution of the input signal. Screens of
computers with a lower display resolution than the projector are displayed smaller
but clearer than in other aspect ratios.
There may be some cases when this cannot be selected, depending on the input signal
and/or resolution.
Selecting an Aspect Ratio
Press the ASPECT button on the remote control and select an appropriate aspect
ratio. Press the ASPECT button to change the aspect ratio type.
Remote control
Example:
You can also select any aspect ratio from [Aspect] in the menu. (P93)
64
Projection Procedure
Step 5 Adjusting Keystone Distortion
■ Horizontal/Vertical Keystone Adjustment
1
Press the KEYSTONE button on the remote control or projector to display
the horizontal-vertical keystone adjustment window. (When [Keystone] is
set to [Horizontal-vertical keystone].)
Remote control
Projector
65
Projection Procedure
• Keystone correction may not be effective in some lens shift positions.
• If keystone distortion is excessive and cannot be fully corrected, straighten the
projector so that it faces the screen directly.
• Signals are processed digitally when keystone distortion is corrected. The image may
look different from the original one. In addition, the aspect ratio of the image may
change.
Basic Guide
To correct keystone distortion (Keystone adjustment), press the KEYSTONE
button.
Two types of adjustment are available: horizontal/vertical adjustment and corner
adjustment.
Use horizontal/vertical keystone adjustment to adjust image width or height
distortion separately, and use corner adjustment to adjust the position of each
corner of the image.
For instructions on switching keystone adjustment, refer to “Keystone” (P107).
Projection Procedure
2
Press the pointer buttons to adjust the dimensions.
Remote control
Projector
To correct bottom distortion,
press the [ ] button.
To correct top distortion,
press the [ ] button.
Screen
To correct distortion on the left,
press the [ ] button.
3
To correct distortion on the
right, press the [ ] button.
When keystone distortion has been corrected, press the OK button.
■ Corner Adjustment
1
Press the KEYSTONE button on the remote control or projector to display
the corner adjustment window. (When [Keystone] is set to [Corner
adjustment].)
Remote control
Projector
66
Projection Procedure
2
Press the pointer button of the corner for correction, and then press the
OK button.
Remote control
Press the pointer buttons to adjust the corner.
Remote control
Basic Guide
3
Projector
Projector
Projection Procedure
4
When you have finished correcting, press the OK button.
■ Resetting the Keystone Adjustment
Reset adjustment as follows.
First, press the KEYSTONE button on the remote control twice to display the
[Keystone reset] window.
Next, select [OK] with the [ ] button, and then press the OK button.
Your specified keystone adjustment is now reset.
67
Projection Procedure
Step 6 Select the Image Quality (Image Mode)
You can select an image mode to suit the projected image.
In each image mode, you can further adjust the brightness, contrast, sharpness,
gamma, HDR range, color adjustment (P100), advanced adjustment (P100), light
source mode (P104) and brightness level. (P104)
Image Modes
Available image modes vary depending on the selected input signal.
: Compatible
Image
mode
: Not compatible
Compatible input signals
Digital PC
Functions
(1) Ambient Brightness
(2) Types of Images
(3) Image Mode Characteristics
HDMI
Standard
(1) Bright
(2) Computer screens, or media played with
video software
(3) Whites and natural colors
Presentation
(1) Bright
(2) Images mainly consisting of text
(3) Keeps the screen bright
Dynamic
(1) Bright
(2) Media played with video software
(3) Keeps the screen bright
Video
(1) Somewhat dark
(2) Video from camcorders
(3) Close to the color space of TVs
Photo/sRGB
(1) Somewhat dark
(2) Digital images from sRGB-compatible
cameras
(3) Conforms to the sRGB standard
DICOM SIM
(1) Somewhat dark
(2) Monochrome images (medical use, for
example)
(3) Adjusted to the GSDF curve specified in
DICOM Standard Part 14
User 1 – 3
Up to 3 user-selected combinations of image
quality settings can be stored in the memory
(P99). Stored profiles are selected as image
modes.
68
Projection Procedure
■ Selecting an Image Mode
Press the IMAGE button on the remote control to select.
The image mode changes each time the IMAGE button is pressed. (The displayed
image modes vary depending on the selected input signal.)
Remote control
Example:
In the DICOM simulation mode (hereinafter referred to as “DICOM SIM”), this
projector can project a monochrome medical image such as an X ray radiography,
CT image, MRI image, etc. in the tone similar to the DICOM (Digital Imaging and
Communications in Medicine) standard. Typically, to project the image according to
the DICOM standard, it requires the grayscale tone correction using a luminance
meter according to the environment. In this projector, there are 21 types of tone
settings for various ambient lights. You can correct the tone in a simplified manner
by selecting the DICOM test pattern (P197).
It is suited to project an image in a medical lecture, academic conference, inhospital conference, etc.
This projector is not the display monitor for a medical image. It cannot be used for
the radiological image reading or medical examination.
• It is recommended to check the tone everytime when using this
projector since it does not have the tone correction and
calibration functions against the secular change.
• It may take approximately 30 minutes until the projection
brightness of this projector becomes stabled.
69
Projection Procedure
Projecting an Image in the DICOM SIM Mode
Basic Guide
You can also select any image mode from the [Image mode] menu. (P98)
• User settings 1 - 3 are displayed when the desired image settings have been
created and stored using the user memory function in the image adjustment
menu. (P98)
Projection Procedure
■ Switching the mode to the DICOM SIM Mode
1
Press the IMAGE button on the remote control until [DICOM SIM] is
displayed or select [DICOM SIM] from [Image mode] in the [Image
adjustment] menu.
2
Display test patterns by pressing the TEST PATTERN button on the
remote control or selecting [On] in [Test pattern] of the [Install settings]
menu. Press the [ ] / [ ] buttons to select the DICOM test pattern.
3
As you view the test pattern, perform [Gamma] adjustment from the
[Image adjustment] menu (P99) until the image is optimal.
4
Press the OK button after the setting.
Perform one of the followings to obtain an appropriate projection:
• Darken the ambient light
• Reduce the image size
• Reduce the projection distance
70
Projection Procedure
Step 7 Turn the Projector Off
1
Press the POWER button to display the window shown below.
Remote control
• The projector cannot be turned on while cooling down.
• Using the projector for extended periods may shorten the life of the internal optical
components.
• Unplug the projector if it will not be used for an extended period.
71
Projection Procedure
When this window is displayed, press the POWER button again to turn off
the power.
After you turn the projector off, projection stops, the [STAND BY] indicator
flashes in red, and the projector starts cooling down. After cooling down, the
projector enters standby mode. In standby mode, the [STAND BY] indicator
remains lit instead of flashing.
If you want to continue projecting without turning off the power, press a button
other than POWER, or else wait until the confirmation message disappears.
Basic Guide
2
Projector
Convenient Features
This section describes features convenient during presentations and in other
situations.
Temporarily Blacking Out an Image
Projection can be temporarily blanked after a presentation, or to divert the
audience’s attention away from the screen.
Remote control
Press the BLANK button to black out the image.
Press the BLANK button again to show the image.
• You can set the screen state while blacking out the image in the menu.
(P118)
Freezing the Picture
Projection can be temporarily frozen during computer operations that would be
distracting, or to pause playback of video or animation.
Remote control
Press the FREEZE button to freeze the moving image. The
projector shows the following icon.
Press the FREEZE button again to return to the original display.
Screen
• It is also cancelled when the input signal is terminated.
Projecting a Test Pattern
Even without any input signals, the projector can project a test
pattern. Test patterns can be projected during installation to check
how the projector is installed.
To project a test pattern, press the TEST PATTERN button on the
remote control.
To stop test pattern projection, press the TEST PATTERN button
again.
For details on projecting test patterns, see “Install settings” (P106) or “Displayed
Test Patterns” (P197).
Remote control
72
Convenient Features
Specifying Power-Saving Settings
Set power-saving settings as needed.
The following four settings are available. For details, refer to the page describing
each function.
• Light source mode (P104)
Conserve energy by selecting a mode that is less bright.
• Power management mode (P124)
Automatically turns off the light source or the power after a certain period if the
projector is idle without an input signal.
Specify the period after which the light source or projector should go off
automatically if left idle without an input signal when [Power management mode]
is set to [Light source off] or [Standby].
Conserves energy in standby mode by disabling some network functions.
73
Convenient Features
• Standby power settings (P124)
Basic Guide
• Power management duration (P125)
74
Safety Instructions
Before Use
Advanced Guide
Installation Procedure
Basic Guide
Connection Procedure
Projection Procedure
Convenient Features
Using Menus
Advanced Guide
Menu Configuration
Menu Settings
Using the Projector on a
Network
Advanced Projection
Other Information
75
Maintenance
Product Specifications
Troubleshooting
Using Menus
Use the menus to set the operation of the projector in detail.
Menu Configuration
The menu screen is divided into 6 tabs as shown below.
[Input settings] tab (P92)
You can set the type of signal or the method of
projection of the images input.
[Image adjustment] tab (P97)
You can adjust the image quality and colors
according to your preference.
[Install settings] tab (P106)
This setting is used when installing the projector.
[System settings] tab (P117)
You can set the operation of the projector.
[Network settings] tab (P135)
These settings are for when using the projector
from a PC via a network.
[Information] tab (P155)
You can check information about the
signal types of the images projected and
other information.
Contents of menu
Menu items
76
Using Menus
Basic Menu Operations
1
Press the MENU button to display the menu window.
Remote control
2
Projector
Press the [ ] / [ ] buttons to select a tab.
Projector
Advanced Guide
Remote control
3
Press the [ ] / [ ] buttons to select an item.
Remote control
Projector
77
Using Menus
• If the tab position is not highlighted in orange, press the [ ] / [ ] buttons to
move the current selection to the top.
Using Menus
4
Select contents.
How to select the contents varies depending on the item.
Selecting from a list Example: Aspect (P93)
1. Select [Aspect].
2. Press the OK button or [ ] button
to display a list of the contents.
3. Use the [ ] / [ ] buttons to select
the desired contents.
4. When you have found the
contents you desired, press the
OK button or [ ].
Adjusting with the [ ] / [ ] buttons Example: Contrast (P99)
1. Select [Contrast].
2. Use the [ ] / [ ] buttons to adjust
the setting.
Selecting from a different screen (1) Example: Register network
password (P141)
1. Select [Register network password].
2. Press the OK button to display a
different screen.
3. Use the [ ] / [ ] / [ ] / [ ] buttons
or number buttons on the remote
control to enter the projector network
password.
78
Using Menus
Selecting from a different screen (2) Example: Random noise reduction
(P101)
1. Select [Advanced adjustment].
2. Press the OK button to display a
different screen.
3. Select [Random noise reduction].
4. Use the [ ] / [ ] buttons to select
the setting.
5. When you have completed the
settings, press the OK button.
5
Advanced Guide
Pressing the MENU button causes the menu screen to disappear.
The menu screen will also disappear if the EXIT button is pressed.
Using Menus
79
Menu Configuration
Input settings (P92)
Aspect
Auto*
True size
P93
Input level
HDMI
P93
Auto*
Normal
Expanded
Super white
HDMI
P93
Off
On*
Color space
HDMI
P94
Auto*
RGB
YCbCr
Progressive
HDMI
P94
Off
Film/auto*
Video 1
Video 2
25p/30p(PsF)
Input signal details
Input signal
P95
HDR information
HDMI
P96
EOTF
Display primaries [0]
Display primaries [1]
Display primaries [2]
White point
Max display mastering luminance
Min display mastering luminance
Max content light level
Max frame-average light level
Image adjustment (P97)
Image mode
Common
P98
Standard*
Presentation
Photo/sRGB
DICOM SIM
User 1 - 3
HDMI
Dynamic
Video
* Factory default, or state after [Factory defaults] is executed.
80
Menu Configuration
User 1
User 2
User 3
Create profile
(Displayed when [Image mode] is not
[User 1] - [User 3])
Save profile
(Displayed when [Image mode] is [User 1] [User 3])
P99
Baseline image mode
(Displayed when [Image mode] is [User 1] [User 3])
P99
Brightness
P99
Contrast
P99
Sharpness
P99
Gamma (1)
P99
HDR range (2)
P99
Color adjustment
Random noise reduction
P100
P100
Off*
Adjust
P101
Type
Tungsten
Fluorescent*
Level
L
H*
Off*
Weak
Middle
Strong
P101
* Factory default, or state after [Factory defaults] is executed.
(1) When [HDR range] does not appear in the menu
(2) When image mode is [Video] and HDR is [On], or when
image mode is [Video] and HDR is [Auto] and HDR signals
are supplied
(3) In [DICOM SIM] image mode
(4) In [Photo/sRGB] image mode
81
Menu Configuration
Ambient light (4)
Color level
Color balance
Color temperature
Preset 1 (3)
Preset 2 (3)
Preset 3 (3)
Preset 4 (clear base) (3)
Preset 5 (blue base) (3)
R Gain
G Gain
B Gain
R Offset
G Offset
B Offset
Advanced Guide
Advanced adjustment
P99
Menu Configuration
MPEG noise reduction
Off*
Weak
Middle
Strong
P101
Dynamic gamma
Off*1
Weak
Middle
Strong
P102
Dynamic contrast
Off*
Mode 1
Mode 2
Mode 3
P102
Colorimetry (1)
Auto*
BT.709
BT.2020
P102
HDR
Auto*
Off
On
P102
Mem. color correct
Flesh
Sky
Green
6-axis color adjust
Off*
Adjust
Hue
Saturation
Brightness
Reset
Fine-Tune Gamma (2)
Light source mode
Off*2
Weak
Middle
Strong
P103
P103
P104
Normal*
Quiet 1
Quiet 2
Adjust
Brightness level adjustment
Brightness level (3)
P105
Reset
P105
P104
* Factory default, or state after [Factory defaults] is executed.
Under the following setting, differs from factory defaults.
*1 [Weak] in [Dynamic] image mode with HDMI input.
*2 [Weak] in [Dynamic]/[Video] image mode with HDMI input.
(1) In [Video] image mode
(2) When image mode is not [DICOM SIM] and [HDR range]
does not appear in the menu
(3) When the operating mode is not [Normal]
82
Menu Configuration
Install settings (P106)
Positional lock
Off*
On
P107
Image flip H/V
None*
Ceiling mounted
Rear
Rear, Ceiling mounted
P107
Keystone
Horizontal-vertical keystone*
Corner adjustment
Reset
P107
Professional settings
P108
4096x2160*
4096x2400
P108
Multi input mode select
DVI input mode
Normal*
Single
DVI 1x2
DVI 2x2
DVI 1x4
P108
Advanced Guide
Panel drive mode
HDMI input mode
Normal*
Single
HDMI 1x2
DVI optimizer
P109
Menu Configuration
DVI dual link auto setting
Off
On*
DVI-1 - 4 equalizer setting
HDMI EDID mode select
P109
HDMI-1 EDID mode
Wide bandwidth (4K60Hz)*
High compatibility
HDMI-2 EDID mode
Wide bandwidth (4K60Hz)*
High compatibility
RGB alignment
Micro-digital image shift
Off*
Adjust
Registration
Off*
Adjust
Advanced registration
Off*
Adjust
5-point adjustment
Off*
Adjust
Manual adjustment
Reset
P110
* Factory default, or state after [Factory defaults] is executed.
83
Menu Configuration
High altitude
Off*
On
P111
Operating mode
Normal*
Fixed brightness
Long duration 1
Long duration 2
P111
Marginal focus
Off*
On
Reset
P112
Edge blending
Off*
Adjust
Left
Right
Top
Bottom
Color blending adjustment
Black level adjustment
Marker
Reset
P112
Lens - Position
Load position 1 - 3
Save position 1 - 3
Lens shift reset
P115
Screen color
Normal*
Greenboard
Adjust
R/G/B Gain
R/G/B Offset
P115
Iris
Open*
Close 1 - 3
P116
Test pattern
Off
On
P116
System settings (P117)
User screen settings
P118
Logo capture
P118
Logo position
Upper L
Upper R
Center*
Lower L
Lower R
P118
No signal screen
Black
Blue*
User logo
P118
* Factory default, or state after [Factory defaults] is executed.
84
Menu Configuration
Screen when blank
Black*
Blue
Light source off
User logo
P118
Projector on
Skip
Canon logo*
User logo
P118
On screen
P119
P119
Menu display time
Normal*
Extended
P119
Menu rotation
Auto
Off*
90 degrees counterclockwise
90 degrees clockwise
P120
Guide
Off
On*
P120
Show input status
Off
On*
P120
Air filter warning display
Off
On*
P120
Overheat warning display
Off*
On
P121
Remote control/Side control
P121
Beep
Off
On*
P121
Key repeat
Off
On*
P121
Key lock
Off*
Main unit
Remote (wireless)
P121
Remote control channel
Ch1 - 4
Independent*
P122
* Factory default, or state after [Factory defaults] is executed.
85
Menu Configuration
Upper L
Upper R
Center*
Lower L
Lower R
Advanced Guide
Menu position
Menu Configuration
Audio in terminal select
P123
DVI-1
Off
Audio in*
DVI-2
Off
Audio in*
DVI-3
Off
Audio in*
DVI-4
Off
Audio in*
HDMI-1
Off
Audio in
HDMI-1*
HDMI-2
Off
Audio in
HDMI-2*
DVI 1x2
Off
Audio in*
DVI 2x2 / 1x4
Off
Audio in*
HDMI 1x2
Off
Audio in
HDMI-1*
HDMI-2
Serial communication
Power supply settings
Baud rate
Data bits
Parity
Stop bit
P123
1*
2
P123
Standby power setting
Normal
Low-power*
P124
Quick startup
Off*
On
P124
Power management mode
Disabled
Light source off
Standby*
P124
Power management duration
5 min.
10 min.
15 min.*
20 min.
30 min.
60 min.
P125
Direct power on
Off*
On
P125
* Factory default, or state after [Factory defaults] is executed.
86
Menu Configuration
Motion blur reduction
Off*
Weak
Strong
Language
English*
German
French
Italian
Spanish
Portuguese
Swedish
Russian
Dutch
Finnish
Norwegian
Other settings
Password settings
P125
Turkish
Polish
Hungarian
Czech
Danish
Arabic
Chinese (Simplified)
Chinese (Traditional)
Korean
Japanese
P126
P127
Off*
On
P128
Date and time settings
P128
Date*
Time
P128
Date display format
Year/month/date*
Month/date/year
Date/month/year
P128
Daylight saving time
Off*
On
Edit
P128
Menu Configuration
Date and time
Start date and time
Month
Day of week
Time
End date and time
Month
Day of week
Time
Region
SNTP
Schedule
Default
P128
On (IPv4)
On (IPv6)
Off*
P129
P129
Off*
On
Edit
Day of week
Edit schedule
Reset
Copy schedule to different day
* Factory default, or state after [Factory defaults] is executed.
87
Advanced Guide
Register password
P127
Menu Configuration
Special period 1
Off*
On
Edit
Period
Day of week
Edit schedule
Reset
Copy schedule to different day
Special period 2
Off*
On
Edit
Period
Day of week
Edit schedule
Reset
Copy schedule to different day
Special period 3
Off*
On
Edit
Period
Day of week
Edit schedule
Reset
Copy schedule to different day
Special period 4
Off*
On
Edit
Period
Day of week
Edit schedule
Reset
Copy schedule to different day
Special period 5
Off*
On
Edit
Period
Day of week
Edit schedule
Reset
Copy schedule to different day
Calibration
P132
Gamma restore
Off*
Adjust
P132
Adjust panel temperature
Off*
Adjust
P133
Light source calibration
OK* / Cancel
P133
Off*
Link with power
P133
Trigger out
* Factory default, or state after [Factory defaults] is executed.
88
Menu Configuration
Air filter counter
Power counter
Reset / Return
P133
P133
Firmware
Yes / No
P134
Factory defaults
OK / Cancel
P134
Network settings lock
Unlock
Lock*
P141
Network password setting
Off
On*
P141
Network settings (P135)
Register network password
Network (wired/wireless)
Off/Off*
On/Off
On/On (Pj AP)
Off/On (Pj AP)
Off/On (Infra)
P142
P142
MAC address
IP address
Subnet mask
Gateway address
DHCP
Off*
On
TCP/IP settings
IP address
Subnet mask
Gateway address
IPv6
Off*
On
Detailed IPv6 address settings
Link local
Auto
Manual
Gateway
Auto settings
Off*
On
Manual settings
IP address
Prefix length
Gateway address
Network setting initialization
Yes / No
* Factory default, or state after [Factory defaults] is executed.
89
Menu Configuration
Detailed IPv4 address settings
Advanced Guide
Detailed settings (wired)
P141
Menu Configuration
Detailed settings (wireless)
P147
Mode
SSID
Security
Channel
Signal strength
MAC address
Wi-Fi Protected Setup
PBC
PIN
Manual settings
Mode
SSID
Security
Open
WEP
WPA2 AES
WPA / WPA2 TKIP / AES
Channel
Key ID
Key type
Key
Detailed IPv4 address settings
IP address
Subnet mask
Gateway address
DHCP
Off*
On
TCP/IP settings
IP address
Subnet mask
Gateway address
IPv6
Off*
On
Detailed IPv6 address settings
Link local
Auto
Manual
Gateway
Auto settings
Off
On*
Manual settings
IP address
Prefix length
Gateway address
Network setting initialization
Yes / No
PJLink
Off
On*
P152
* Factory default, or state after [Factory defaults] is executed.
90
Menu Configuration
AMX Device Discovery
Off*
On
P153
Crestron RoomView
Off*
On
P153
Information
E-mail sender address
E-mail recipient address
Detailed information (wired)
IPv4
IPv6
Link local
Auto
Manual
Detailed information (wireless)
IPv4
IPv6
Link local
Auto
Manual
P154
Advanced Guide
Information (P155)
The following settings are not reset even when factory defaults are restored.
• Selected input signal
• Image adjustment
- Save profile
- Baseline image mode
- Light source mode
- Brightness level
• Install settings
- Lens - Position
• System settings
- Registration
- Advanced registration
- High altitude
- Operating mode
- Marginal focus setting value
- Remote control channel
- Serial communication (Stop bit)
- Standby power setting
- Quick startup
- Language
- Date and time settings
- Schedule
- Gamma restore
- Adjust panel temperature
- Trigger out
- Power counter
- Air filter counter
- Firmware
• Network settings
• Information
* Factory default, or state after [Factory defaults] is executed.
91
Menu Configuration
Model name
Input signal
Firmware
Serial no.
Projector usage time
IP address (wired)
IP address (wireless)
Projector name
Comments
System information ID
Menu Settings
Input settings
This section describes settings for aspect ratio, etc.
(When the input signal is HDMI-1)
Menu
Function
Details
Aspect
Select an image aspect ratio.
P93
Input level
Select the input level for HDMI signal.
P93
Super white
Select super white mode for HDMI signal.
P93
Color space
Select the color space for HDMI signal.
P94
Progressive
Select the I/P conversion method used for interlaced
signal input.
P94
Input signal details
Shows input signal details for each input terminal used.
P95
HDR information
Shows the Dynamic Range and Mastering InfoFrame
for HDMI signals.
P96
Menus that are not available are grayed out or hidden.
92
Menu Settings
Aspect
> [Input settings] > [Aspect]
Select a projection aspect ratio for images.
Option
Function
Auto
An image is projected at the aspect ratio of the input signal.
True size
The image is projected with the original resolution of the input
signal.
Menus that are not available are hidden.
The ASPECT button on the remote control can also be used to select the [Aspect]
settings.
Input level
> [Input settings] > [Input level]
Adjust the input level for content projected via HDMI.
Option
Function
Automatically switches the input level based on the input signal.
Normal
Limits the input level to 16 - 235.
Expanded
Enables a full input level of 0 - 255.
Super white
> [Input settings] > [Super white]
Select to project white signals in HDMI input that are in a range of 16-235 at 100%109% brightness (235-255).
Option
Function
Off
Disable super white. Project white signals with an input level of 235 at
100% brightness. All white signals with an input value exceeding 235
are also projected at 100% brightness.
On
Convert input signals in a range of 16-235 so that an input level of 255
is projected as white 109% at 100% brightness.
• Super white has no effect when [Input level] is set to [Expanded].
• Switch this setting to [Off] if projection looks distorted or unnatural when it is [On].
• Setting this option to [On] will darken the overall image.
93
Menu Settings
• This setting is only available with RGB HDMI signals.
• In [Auto] mode, the signal level is selected automatically. (Some equipment may not
support this.)
• If the HDMI output of the connected equipment can be set to [Normal] or [Expanded],
we recommend [Expanded]. The contrast of images will be improved and dark scenes
will be rendered more realistically. In this case, set the projector’s [Input Level] to [Auto]
or [Expanded].
For more detailed information, refer to the user’s manual for the equipment connected
to the projector.
Advanced Guide
Auto
Menu Settings
Color space
> [Input settings] > [Color space]
Select the color space for HDMI signal.
Option
Auto
Function
Selects the optimal color format for input signals.
RGB
Forces the projector to handle the input signal as an RGB signal.
YCbCr
Forces the projector to handle the input signal as a color difference
signal.
Progressive
> [Input settings] > [Progressive]
Performs progressive processing optimized for still images in cinematic content or
moving images in videos, when interlaced HDMI signals are supplied.
Option
Function
Off
Does not perform progressive processing.
Film/auto
Suitable for still images or typical moving images. Performs progressive
processing optimized for video or cinematic content.
Video 1
Suitable for projecting video with high image quality and relatively slow
movement. Performs progressive processing optimized for HD video.
Video 2
Suitable for projecting video with faster movement. Performs
progressive processing optimized for fast-moving video.
25p/30p (PsF)
Performs progressive processing optimized for 1080 Psf/25 or
1080 Psf/30 video (25 or 30 fps, respectively).
Select [Off] when flickers and horizontal lines are noticeable in media that has a lot of
fast-moving action.
94
Menu Settings
Input signal details
> [Input settings] > [Input signal details]
Shows input signal details for each input terminal used, for the selected input
signals.
In Multi Input mode, terminals with incorrect input can be identified by a “ ” icon, which
is displayed for input terminals with signals that do not meet the requirements.
• HDMI input
Indicates the resolution, vertical frequency, color format (for YCbCr, the color
format and subsampling; for RGB, the color format and range), color depth, VIC,
and colorimetry information.
• DVI input
Indicates the resolution and vertical frequency.
Advanced Guide
In the example above, the HDMI-1/2 input signal has a resolution of 2048 x 2160,
a vertical frequency of 60.000 Hz, a color format of YCbCr/subsampling 444, and
a color depth of 8 bits.
If no additional information from the input signal is displayed, it is marked with “*”.
Menu Settings
In the example above, the DVI-1/2/3/4 input signal has a resolution of 1024 x
2160, and a vertical frequency of 60.000 Hz.
95
Menu Settings
HDR information
> [Input settings] > [HDR information]
When HDMI signals are supplied, shows the Dynamic Range and Mastering
InfoFrame information.
The projector determines and indicates whether HDMI signals are SDR or HDR.
HDR HDMI signals have an area that includes color and luminance information,
and this information is indicated. The following information is displayed.
Item
Information Indicated
Details
Indicates
various
gamma
information of
the video
content
Traditional gamma-SDR
SDR signal
SMPTE ST 2084
HDR signal
Display primaries [0],[1],[2]
x: 0.00002 – 1.00000
y: 0.00002 – 1.00000
Coordinates of the three
vertices of the gamut triangle
in the color space
White point
x: 0.00002 – 1.00000
y: 0.00002 – 1.00000
Coordinates of “white” in the
color space
Max display mastering
luminance
1 – 65535 cd/m2
Maximum luminance of the
display used when the video
content was produced
Min display mastering
luminance
0.0001 – 6.5535 cd/m2
Minimum luminance of the
display used when the video
content was produced
Max content light level
1 – 65535 cd/m2
Maximum luminance of
scenes in the video content
Max frame-average light
level
1 – 65535 cd/m2
Average luminance of scenes
in the video content
EOTF
96
Menu Settings
Image adjustment
This section describes image quality settings such as brightness, contrast,
and sharpness.
(When the input signal is HDMI-1)
Menu
Image mode *
Select overall image quality to suit the projected image.
P98
Create profile
Save desired image quality settings as profiles.
P99
Baseline image mode
Only displayed when the image mode is set to a profile
from [User 1] to [User 3]. Shows the image mode that
was modified to create the profile.
P99
Brightness *
Adjust image brightness.
P99
Contrast *
Adjust image contrast.
P99
Sharpness *
Adjust image sharpness.
P99
Gamma *
Correct loss of detail in shadows or highlights.
P99
HDR range *
Within the dynamic range of SMPTE ST 2084, set the
range to use.
P99
Color adjustment *
Fine-tune image colors.
P100
Advanced adjustment *
Fine-tune noise reduction and color tone.
P100
Light source mode *
Adjust projection brightness and operating sounds.
P104
Brightness level *
Adjust projection brightness as controlled by the drive
current of the laser diode.
P105
Reset
Restore the current image quality settings to defaults.
P105
Menus that are not available are grayed out or hidden.
* Adjustments are stored as modified settings for the current input signal and image
mode.
97
Menu Settings
Details
Advanced Guide
Function
Menu Settings
Image mode
> [Image adjustment] > [Image mode]
Select the overall image quality for projected images. Can also be selected by
pressing the IMAGE button on the remote control.
Option
Types of Images
Characteristics
Standard
Computer screens, or media
played with video software
Bright overall; white, with natural
colors
Presentation
Images mainly consisting of text
Bright overall
Dynamic
Video content
Bright overall
Video
Video from camcorders
Somewhat dark; colors resemble
TV
Photo/sRGB
Digital images from sRGBcompatible cameras
Somewhat dark; conforms to the
sRGB standard
DICOM SIM
Medical or other monochrome
images
Conforms to DICOM Standard
Part 14. However, the projector
cannot be used in diagnosis or
similar applications.
User 1 - 3
Up to 3 user profiles can be stored for your selected image quality
settings. Stored profiles are available in this setting as an image mode.
Menus that are not available are grayed out or hidden.
• You can adjust the image quality by adjusting the following items in each image mode:
[Brightness], [Contrast], [Sharpness], [Gamma], [HDR range], [Color adjustment],
[Advanced adjustment], [Light source mode], and [Brightness level]
• If flickering occurs when the image mode is set to [Presentation], try switching to
[Photo/sRGB] or [Standard].
98
Menu Settings
Create profile
> [Image adjustment] > [Create profile]
Save desired image quality settings in up to 3 user profiles.
• The saved settings are [Brightness], [Contrast], [Sharpness], [Gamma], [HDR range],
[Color adjustment], [Advanced adjustment], [Light source mode], and [Brightness level].
• Although only 3 user profiles are displayed, separate profiles apply depending on
whether DVI-D or HDMI signals are supplied. As a result, it is possible to save up to
6 settings.
• The image mode name which was the basis for the settings change is also saved in the
user memory. When a user memory is selected as the image mode, the image mode
that was the base for that user memory is displayed in the menu as [Baseline image
mode].
Brightness
> [Image adjustment] > [Brightness]
Adjust image brightness.
Contrast
Advanced Guide
> [Image adjustment] > [Contrast]
Sharpen or soften image contrast.
Sharpness
> [Image adjustment] > [Sharpness]
Adjust image sharpness.
> [Image adjustment] > [Gamma]
Correct image areas that are too dark or too bright to see clearly.
For more detailed adjustment, use Fine-Tune Gamma (P104).
HDR range
> [Image adjustment] > [HDR range]
Within the dynamic range of SMPTE ST 2084, set the range to use.
[Gamma] is not shown when the menu includes [HDR range].
[HDR range] can only be set in the following cases.
• Image mode (P98) is set to [Video] and HDR (P102) is [On]
• Image mode (P98) is set to [Video], HDR (P102) is [Auto], and HDR signals are
supplied
99
Menu Settings
Gamma
Menu Settings
Color adjustment
> [Image adjustment] > [Color adjustment]
Adjust color-related settings such as color level, color balance, and color
temperature.
(In image modes other than DICOM SIM.)
Submenu
Function
Color level
Adjusts the intensity of colors.
Color balance
Adjusts the color balance of a purplish or greenish image.
Color temperature
Adjusts the white color temperature.
R / G / B Gain
Adjust the gain of each color.
R / G / B Offset
Adjusts the color offset of each color.
In [DICOM SIM] image mode, [Color temperature] is not adjusted with numeric values but
set to one of the following five presets.
Preset 1: Prioritize brightness, relative to DICOM Standard Part 14.
Preset 2: Prioritize color tone, relative to DICOM Standard Part 14.
Preset 3: Adjust color to conform to DICOM Standard Part 14.
Preset 4: Reproduce colors of X-ray film (Clear base).
Preset 5: Reproduce colors of X-ray film (Blue base).
Advanced adjustment
> [Image adjustment] > [Advanced adjustment]
Fine-tune noise reduction and color tone.
100
Menu Settings
Ambient light
Minimize the effect of ambient light on the screen.
Submenu
Off
Function
No correction is performed.
Tungsten
For ambient light from conventional light bulbs
or fluorescent light of this color.
Fluorescent
For ambient light from a “day white” fluorescent
source.
Type
Adjust
Level
L
For an ordinary brightness of ambient light.
H
For bright ambient light.
Examples of Ambient Light Level Settings
Level
Example Location
L
Projection room, sports bar, etc.
H
Conference room, lecture room, etc.
• This setting is available when the image mode is set to [Photo/sRGB].
• This setting is available when the baseline image mode is set to [Photo/sRGB].
Reduce image noise associated with random frequencies and amplitudes.
Option
Off
Function
Disables random noise reduction.
Weak
Middle
Specify one of three levels of intensity of the random noise reduction.
Select [Weak] for fast-moving images or [Strong] for slow-moving images.
MPEG noise reduction
Reduce MPEG image noise.
Option
Off
Function
Disables MPEG noise reduction.
Weak
Middle
Specify one of three levels of intensity of the MPEG noise reduction.
Strong
101
Menu Settings
Strong
Advanced Guide
Random noise reduction
Menu Settings
Dynamic gamma
You can adjust the gradation representation of light and dark portions of an image
automatically.
Option
Off
Function
Disable dynamic gamma adjustment.
Weak
Middle
Specify one of three levels of dynamic gamma adjustment.
Strong
Dynamic contrast
For dark images, makes dark image areas even darker.
Option
Function
Off
Disable dynamic contrast adjustment.
Mode 1
Suitable for videos and slideshows.
Enhances contrast slightly, and suits bright viewing environments. Contrast
is adjusted automatically in response to changes in the input signal.
Mode 2
Suitable for slideshows and videos with scenes that change gradually, as for
landscapes. Enhances contrast, and suits dark viewing environments.
Contrast is adjusted automatically in response to changes in the input signal.
Mode 3
Suitable for videos with many scene changes. Enhances contrast, and suits
dark viewing environments. Contrast is adjusted automatically and more
aggressively in response to changes in the input signal.
Colorimetry
Select the input color space.
Option
Function
Automatically determine the optimal color space (BT.709 or BT.2020) based
on input signals.
Auto
BT.709
Forces use of the BT.709 color space.
BT.2020
Forces use of the BT.2020 color space.
[Colorimetry] can only be set when the image mode (P98) is [Video].
HDR (High Dynamic Range)
HDR range adjustment projects an expanded range of image luminance, preserving detail in
highlights and shadows.
Option
Auto
Function
Automatically use HDR when HDR signals are supplied.
Off
Prevent use of HDR.
On
Require use of HDR.
[HDR] can only be set when the image mode (P98) is [Video].
102
Menu Settings
Mem. color correct (Flesh/Sky/Green)
Enhances skin tones, blue skies, and greens, so that these colors are more consistent with
people’s remembered impressions.
Option
Off
Function
Disable correction.
Weak
Middle
Specify the level of correction.
Strong
Image resolution may seem lower when [Random noise reduction] or [MPEG noise
reduction] is applied.
6-axis color adjust
Fine-tune RGB (red, green, blue) and CMY (cyan, magenta, yellow) hues in images.
Submenu
Off
Function
Disables 6-axis color adjustment.
Advanced Guide
Adjust
Reset
Returns all adjustment values to zero.
103
Menu Settings
Use the [ ] / [ ] buttons to select [ Hue], [ Saturation], or
[ Brightness], and use the [ ] / [ ] buttons for adjustment.
Menu Settings
Fine-Tune Gamma
Adjust white, red, green, and blue gamma curves. Red, green, and blue can be adjusted
separately. Adjustments to white are also applied to the three other colors. Note that adjusting
any color will overwrite previous adjustments.
Use the [ ] / [ ] buttons to select a color, and then press the OK button. Next, use the [ ] /
[ ] buttons to select an adjustment point and the [ ] / [ ] buttons for adjustment.
• [Fine-Tune Gamma] is available in image modes other than [DICOM SIM], and when
[HDR range] does not appear in the menu.
• For details on gamma correction, see page 99.
• Use input signals or a test pattern for adjustment.
Light source mode
> [Image adjustment] > [Light source mode]
Reducing projection brightness reduces power consumption and fan noise.
Option
Function
Normal
Projects images at full brightness.
Quiet 1
Select to reduce brightness, or when quiet projection is required.
Quiet 2
Reduces brightness and noise further.
Based on your specified brightness, fan speed is adjusted
automatically.
Use the [ ] / [ ] buttons to adjust the brightness on the Brightness
level adjustment screen that appears.
Adjust
[Brightness level] is shown when the light source mode is set to
[Adjust].
[Light source mode] is displayed when the operating mode is [Normal]. If the operating
mode (P111) is not set to [Normal], [Brightness level] appears instead of [Light source
mode].
104
Menu Settings
Brightness level
> [Image adjustment] > [Brightness level]
Control the laser diode to adjust the projection brightness.
Use the [ ] / [ ] buttons to adjust the brightness.
[Brightness level] appears instead of [Light source mode] when the operating mode
(P111) is not set to [Normal].
> [Image adjustment] > [Reset]
Restore the current image quality settings to defaults.
Option
Function
Resets the image adjustment settings.
Cancel
Cancels resetting of the image adjustment settings.
• Performing reset when [Image mode] is set to a profile from [User 1] to [User 3] will
restore the settings originally saved for that user profile.
• Only the setting for the combination of input signal and image mode for the current
projection is reset.
• The following settings are reset (initialized).
• Brightness
• Contrast
• Sharpness
• Gamma
• HDR range
• Color level
• Color balance
• Color temperature
• R/G/B Gain
• R/G/B Offset
• Ambient light (Type/
• Random noise
Level)
reduction
• MPEG noise reduction
• Dynamic gamma
• Dynamic contrast
• Colorimetry
• HDR
• Mem. color correct
• 6-axis color adjust
• Fine-Tune Gamma
• Light source mode
(Hue/Saturation/
(White/Red/Green/Blue)
Brightness)
• Brightness level
105
Menu Settings
OK
Advanced Guide
Reset
Menu Settings
Install settings
Adjust projection to suit the screen or the type of images, or how the
projector is installed.
(When the input signal is HDMI-1)
Menu
Function
Details
Positional lock
Operation of installation related functions can be
prohibited.
P107
Image flip H/V
Specify settings for projection from behind the screen,
from the ceiling, or both.
P107
Keystone
Specify the type of keystone adjustment.
P107
Professional settings
Specify advanced installation settings.
P108
Lens - Position
Store information about the lens position (including
focus, zoom, and lens shift settings), which can be
used to restore the lens to these positions.
P115
Screen color
Adjust projection colors to suit the screen color.
P115
Iris
The aperture value can be adjusted in a range of 1-3.
A smaller aperture reduces brightness but improves
contrast.
P116
Test pattern
Project a test pattern to check the resolution and color
of projection during installation.
P116
Menus that are not available are grayed out.
106
Menu Settings
Positional lock
> [Install settings] > [Positional lock]
Operation of installation-related functions can be prohibited.
• Image flip H/V • Keystone • Professional settings • Lens - Position (Save
position, Lens shift reset)
Option
Function
Off
Enables adjustment of installation-related functions.
On
Prevents adjustment of installation-related functions.
Image flip H/V
> [Install settings] > [Image flip H/V]
Specify the orientation of how the projector is installed.
Option
Function
Select for normal projection, without inversion.
Ceiling mounted
Select when the projector is installed upside-down.
The projected image is inverted in the vertical direction.
Rear
Select this to project an image from behind the screen.
The projected image is inverted in the horizontal direction.
Rear, Ceiling mounted
Select when the projector is installed upside-down on the ceiling
and behind the screen.
The projected image is inverted in both vertical and horizontal
directions. Select when the projector is installed upside-down.
Keystone
> [Install settings] > [Keystone]
Specify either [Horizontal-vertical keystone] or [Corner adjustment] keystone
adjustment. Keystone adjustment can also be reset. Keystone adjustment can also
be applied by pressing the KEYSTONE button on the remote control.
Option
Function
Horizontal-vertical
keystone
Apply horizontal-vertical keystone adjustment. Image height and
length is adjusted.
Corner adjustment
Apply corner adjustment. Each corner of the image can be
repositioned.
Reset
Resets any adjustments to the keystone value.
107
Menu Settings
• When mounting the projector on a ceiling, use the optional ceiling attachment (RSCL15) and ceiling-mount arm (RS-CL17). Contact the Canon Customer Support Center
for more detailed information.
• Image flipping will reset any adjustment for keystone distortion. In this case, redo the
adjustment.
• Adjusting the [Image flip H/V] setting does not alter button assignments in the
projector’s side controls.
Advanced Guide
None
Menu Settings
Professional settings
> [Install settings] > [Professional settings]
Specify advanced installation settings.
Panel drive mode
Select the LCD panel vertical resolution to use.
Option
Function
4096x2160
Use a resolution of 4096 x 2160 lines.
4096x2400
Use a resolution of 4096 x 2400 lines.
• Select [4096x2400] only when a signal with a resolution of 4096 x 2400 is supplied.
• Changing the panel drive mode resets the following values.
- Horizontal-vertical keystone
- Corner adjustment
• Adjustment values stored for edge blending vary depending on the panel drive
mode.
Multi input mode select
Select how to combine four DVI inputs or two HDMI inputs to form an image.
Submenu
DVI input mode
HDMI input mode
Option
Function
Normal
For use with [Single], [DVI 1x2], [DVI 2x2], or [DVI 1x4]
DVI input.
Single
For use with a single terminal supplying DVI input.
DVI 1x2
For use with DVI input from two cables.
DVI 2x2
For use with DVI input from four cables, projected in a
2x2 layout.
DVI 1x4
For use with DVI input from four cables, projected side
by side.
Normal
For use with [Single] or [HDMI 1x2] HDMI input.
Single
For use with a single terminal supplying HDMI input.
HDMI 1x2
For use with HDMI input from two cables.
108
Menu Settings
DVI optimizer
Optimizes images from DVI signals.
Submenu
Option
Function
Off
Disable automatic determination of single- or dual-link
mode from DVI terminals, and project images in singlelink mode.
On
Automatically determine whether DVI terminals are used
in single- or dual-link mode and switch settings
accordingly.
DVI dual link auto
setting
Option
DVI-1 equalizer
setting
DVI-2 equalizer
setting
DVI-3 equalizer
setting
DVI-4 equalizer
setting
Function
Adjust the equalizer value for DVI terminals.
Choose lower values for higher amplification, or higher values for lower
amplification.
Example of equalizer settings
• Decrease values to amplify signals that have been attenuated by a
long cable.
• Signals may be too strong if noise occurs when using a short cable, or
when using an active cable, signal corrector, or repeater. If so, increase
values to attenuate and correct the signals.
HDMI EDID mode select
Advanced Guide
• When a dual-link cable is used, any noise in the signal line may prevent normal
projection. If this occurs, set [DVI dual link auto setting] to [Off].
• In some cases when DVI terminals are used, the cable may not be a good match for
the projector, which may cause video noise or prevent the signal from being
detected. If this occurs, adjust values in each setting from [DVI-1 equalizer setting] to
[DVI-4 equalizer setting].
Select an HDMI terminal (1 or 2) EDID that is compatible with connected equipment.
HDMI-1 EDID
mode
HDMI-2 EDID
mode
Function
Option
Function
Wide
bandwidth
(4K60Hz)
Select when connected equipment can supply highbandwidth signals such as 3840 x 2160 (4K) at 60 Hz,
YCbCr 4:4:4.
High
compatibility
Select in case of incorrect video or audio output from
the projector because the EDID is not read correctly by
connected equipment when set to Wide bandwidth
(4K60Hz).
Even if this function is used, the list of supported video formats may not be updated
when [HDMI input mode] in [Multi input mode select] is set to [HDMI 1x2].
109
Menu Settings
Submenu
Menu Settings
RGB alignment
Correct color misalignment.
Submenu
Function
Fine positioning enables adjustment of misalignment relative to images
from other projectors used at the same time, in 1-pixel increments.
Submenu
Off
Disable micro-digital image shift.
Micro-digital image
shift
Submenu
Adjust
Registration
Function
Function
Adjust
Adjust the image vertically and
horizontally.
Chart
Display a chart (point selection
window).
Color misalignment affecting the entire image can be corrected by
moving red, green, or blue components into position, in 1-pixel
increments.
Precise correction of red, green, or blue misalignment in different areas
of the screen is possible by color and area.
For detailed instructions, refer to “Advanced Registration to Adjust
Projected Images” (P187).
[Off]
Disable local correction of color misalignment.
[Adjust]
Display a menu for local correction of color misalignment.
Advanced
registration
Submenu
5-point
adjustment
Function
Off
Disable adjustment.
Adjust
Enter 5-point adjustment mode (in screen
corners and at the center).
Manual
adjustment
Precise adjustment based on 54 points (in a 6 x
9 grid).
Reset
Restore the original position, before adjustment.
With advanced registration, checkered or halftone image areas
may be affected by uneven colors or image artifacts.
110
Menu Settings
• [Registration] and [Advanced registration] settings are retained even if you change
the panel drive mode.
• 5-point adjustment enables basic correction of color misalignment across the
screen, by moving adjustment points in the center and each corner. To correct
registration only in certain areas, try manual adjustment.
• Any values you set in 5-point adjustment are retained if you subsequently perform
manual adjustment. For more precise correction after 5-point adjustment, perform
manual adjustment.
• Any manual adjustment values you set before switching to 5-point adjustment are
cleared.
High altitude
Switch the fan mode to suit installation at low or high altitudes (above 2,300 m [7,545.8']).
Option
Function
Off
Setting for altitudes lower than 2,300 m (7,545.8').
On
Setting for altitudes of 2,300 m (7,545.8') or higher.
Incorrect settings may shorten the useful life of the other parts.
Operating mode
Option
Function
Normal drive mode. Brightness will decrease with time.
Fixed brightness
Maintains nearly the same brightness set at installation. Laser diode
wear is detected by a sensor, and current is increased to compensate for
wear.
Long duration 1
Enables a relatively longer useful life of optical parts by reducing the
brightness level of the light source mode and regulating the fan drive.
Long duration 2
Enables an even longer useful life of optical parts by further reducing the
brightness level of the light source mode and more aggressively
regulating the fan drive.
When using the projector continuously for 24 hours or more, or when turning the
projector off by unplugging it, execute light source calibration using one of the settings
below. If calibration is not executed, the projector will be unable to maintain fixed
brightness.
• Periodically specify [OK] in [Light source calibration] in [Calibration] (P132).
• Specify CALIBRATION in [Schedule] (P129).
111
Menu Settings
Normal
Advanced Guide
Switch the method of controlling the light source and fan.
Menu Settings
Marginal focus
In dome projection, image focus can be adjusted on the edges of the screen, and the remote
control can be used to activate and deactivate this focus adjustment. For detailed instructions,
refer to “Adjusting Peripheral Focus” (P191).
Option
Function
Off
Disable remote focusing of image edges.
On
Enable remote focusing of image edges. To access the adjustment
window, press the LENS button on the projector twice or press the
FOCUS button on the remote twice.
Reset
Restore edge focusing to the standard position.
Setting this function to [Off] only prevents display of the adjustment window.
Adjustment values are still retained. Use this setting to prevent remote focusing of
image edges.
Edge blending
Brightness and colors of overlapping edges of images from multiple projectors, which form a
blending area, can be adjusted for a more seamless appearance. For detailed instructions, see
“Projecting from Multiple Projectors at Once (Edge Blending)” (P183).
[Off]
Disable blending.
[Adjust] Display the menu for blending area adjustment.
Start marker
End marker
Blending area
When adjusting the image
projected from the right side
• Adjustment may not eliminate different colors or brightnesses in the blending area.
• For best edge-blending results, use all projectors in the same image mode (Optimal
image mode: [Photo/sRGB].) and make the following adjustments.
(1) Brightness, contrast, R/G/B gain, R/G/B offset, black level, color blending, color
temperature, color level, color balance, sharpness, gamma, HDR range, light source
mode, brightness level
(2) Color adjustment, by using 6-axis color adjustment
(3) Gamma adjustment, by fine-tuning gamma
(4) Corner adjustment, using keystone correction
112
Menu Settings
Submenu
Function
Submenu
Function
Left
Right
Top
Select the direction of the blending area to adjust.
Bottom
Width
Specify the width between the start and end markers.
Moves the position of the start marker.
Side
Start
position
• Large blending areas may cover input signal
dialog boxes and other interface elements.
In this case, momentarily set edge blending
to [Off] and check the display.
• Although the starting marker is normally
aligned with the image edge, it can also be
aligned toward the center of the image. In
this case, the black blending area will lie
outside of the starting marker.
Adjust unwanted colors or discrepancies between colors in the blending
area.
Off
Function
Do not adjust colors of blended images.
Adjust unwanted colors or discrepancies between
colors in the blending area.
Option
Adjust
Function
White
Simultaneously adjust red,
green, and blue to correct
unwanted colors or
discrepancies in the blending
area.
Red/Green/Blue
Individually adjust red, green,
and blue to correct unwanted
colors or discrepancies in the
blending area.
113
Menu Settings
Color blending
adjustment
Advanced Guide
Submenu
Menu Settings
Submenu
Function
Because black is lighter in the blending area than in other areas, you can
adjust the black level outside the blending area to make this difference in
brightness less noticeable.
Position of end
marker (hidden)
Left image
Area A: Black level cannot be adjusted.
Area B: Adjust to a black level different
from that of area D.
Area C: Adjust to provide a smooth
transition relative to the black
levels of areas B and D.
CBA
Area D
Blending area
Areas C - A (default: 0)
Off
Do not adjust the black level.
Black level
adjustment
Area
Adjust areas C - A to smoothen the boundaries of the blending area.
Submenu
Function
Side
Select the direction to adjust from Left/Right/Top/
Bottom.
A-Width/
B-Width/
C-Width
Adjust the widths of areas A - C.
Black level
Adjust the black level brightness and color of areas B and D.
Submenu
B/D-area
base
Function
Adjust the black level brightness of B/D areas.
B/D-area red / Adjust the red, green, and blue components of B/D
green / blue area black levels individually.
Adjustment values are restored even if the dialog box is no longer
displayed after you select [Adjust] again after setting [Black level
adjustment] to [Off].
Show the blending area markers.
Option
Marker
Reset
Function
Off
Hide the blending area markers.
On
Show the blending area markers. The start marker is
red, and the end marker is green.
Reset the marker settings.
114
Menu Settings
Lens - Position
> [Install settings] > [Lens - Position]
The projector can store information about the lens position. Up to three sets of lens
information (including, focus, zoom, and lens shift settings) can be saved, and the
lens can be restored to these positions as needed.
Submenu
Function
Load position 1-3
Restores the lens to the positions saved using [Save position 1] [Save position 3].
Save position 1-3
Saves the lens position as one of the available positions (1-3).
Lens shift reset
Restores the lens to the original position.
Screen color
> [Install settings] > [Screen color]
Submenu
Function
Normal
Select this if a standard type of projection screen is used. The images
are projected in a light quality similar to that of natural light.
Greenboard
Select if a dark green surface such as a blackboard is used as the
screen. The color quality similar to [Normal] is obtained on the
greenboard.
Adjust
Select to fine-tune the gain and offset of red, blue, and green.
115
Menu Settings
You can adjust the color quality of the images projected according to the color of
the projection screen.
Advanced Guide
• When saved lens positions are restored, images may be slightly misaligned, relative to
the saved position.
• Specifying a somewhat smaller image size than the screen size (image area) enables
you to switch among multiple lens positions without the image extending off the screen.
• When precise positioning is needed, use lens shift, zoom, and focus functions to finetune the position.
• [Save position] and [Lens shift reset] are not available when [Positional lock] is set to
[On] (P107).
• [Load position] is grayed out and not available unless positions have been stored to a
[Save position].
• The following setting values are stored: focus, zoom, lens shift, keystone, corner
adjustment, and screen color.
Menu Settings
Iris
> [Install settings] > [Iris]
Use this feature for projection emphasizing contrast over brightness.
Submenu
Function
Open
Disables aperture adjustment.
Close 1-3
Specify the aperture value in a range of 1-3.
The [Iris] setting does not affect power consumption.
Test pattern
> [Install settings] > [Test pattern]
You can project a test pattern (P197) to check resolution, color, and other details
even without supplying an input signal. Also available by pressing the TEST
PATTERN button on the remote control.
Option
Function
Off
Disable test pattern display.
On
Enable test pattern display.
• While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch
patterns. Additionally, options of test pattern that have options can be changed with the
[ ] / [ ] buttons.
• The test pattern menu is no longer displayed after a little while, but you can view it
again by pressing the [ ] / [ ] buttons.
116
Menu Settings
System settings
Customize projector and remote control operation, beeping, and other
details after startup, during standby, and in other situations.
(When the input signal is HDMI-1)
Menu
Function
Details
P118
On screen
Set the display position and whether to show or hide
menus, help information, and warning or caution icons.
P119
Remote control/Side
control
Specify operation with remote control or projector
buttons.
P121
Audio in terminal select
Select the terminal for audio input.
P123
Serial communication
Display serial communication setting values.
P123
Power supply settings
Specify how power is managed at startup, in standby,
and when no signal is supplied.
P123
Motion blur reduction
Motion blur is blurring that occurs during video
playback. Motion blur reduction can make this blurring
less noticeable.
P125
Language
You can select the language in which the menus are
displayed.
P126
Other settings
Set a password, check the air filter replacement timing,
schedule operation, and access other settings and
information.
P127
Menus that are not available are grayed out.
117
Menu Settings
Customize user screens shown at startup, when no
signal is detected, and in other situations.
Advanced Guide
User screen settings
Menu Settings
User screen settings
> [System settings] > [User screen settings]
Capture a logo and specify logo display settings.
Logo capture
Registers the current image as a user logo. Registered user logos can be shown when no
signal is received, when the BLANK button is pressed, or as the startup image.
Option
Function
OK
Display the image for logo registration.
Align the image with the red boundary lines indicating the portion that
will be stored, and then press the OK button. The portion of the image
within the boundary lines is now registered.
Cancel
Cancels logo registration.
Logo position
Specify the position of registered user logos as follows.
You can specify the position after a logo has been registered. Choose from upper left, upper
right, center, lower left, or lower right.
No signal screen
Customize the screen shown when no input signals are received.
Option
Black
Function
The screen is all black.
Blue
The screen is all blue.
User logo
The user logo is projected.
Screen when blank
Select the screen shown when projection is temporarily blanked out by pressing the BLANK
button on the remote control.
Option
Function
Black
The screen is all black.
Blue
The screen is all blue.
Light source off
The light source is turned off.
User logo
The user logo is projected.
Projector on
Select a logo to project after startup until input signals can be projected.
Option
Function
Skip
A black screen is projected.
Canon logo
Displays the Canon logo that was registered in advance at the factory.
User logo
The user logo is projected.
118
Menu Settings
On screen
> [Sysetm settings] > [On screen]
Specify display details for on-screen menus, help, and warning or precaution icons.
Menu position
Reposition menu display.
Choose from upper left, upper right, center, lower left, or lower right.
Only [Center] is available when edge blending is used. Other display positions are
grayed out and not available.
Menu display time
Option
Function
Normal
The menu is displayed for 10 or 30 seconds.
Extended
The menu is displayed for 3 minutes.
The display times of the following menus are also changed.
Item
[Normal]
-
[Extended]
30 seconds 3 minutes
Input (P55)
Keystone adjustment (P65)
Keystone reset (P67)
Focus (P59), Zoom (P60), Lens shift (P62),
Lens shift reset (P63)
Marginal focus (P112)
Aspect (P64)
Image mode (P68)
Gamma (P99)
Volume adjustment (P29, P34)
10 seconds 3 minutes
The windows for manual adjustment or 5-point adjustment in RGB alignment, and for
other settings such as date and time settings, are shown for 3 minutes, regardless of
the [Normal] or [Extended] option.
119
Menu Settings
Menu screen
Advanced Guide
Extend menu display from the standard 10 or 30 seconds to 3 minutes.
Menu Settings
Menu rotation
Rotate menu display. When projecting in portrait orientation, for example, with the projector
installed at a 90° angle, specify the orientation of projected menus to align them with the top
or bottom of projected images.
Option
Function
Auto
Automatically rotates menus as needed after using an accelerometer to
determine if the projector is installed in portrait orientation (90°
clockwise or counterclockwise) or horizontally.
Off
Menus are not rotated. Menus are shown in a readable orientation for
projectors installed horizontally.
90 degrees
counterclockwise
90 degrees
clockwise
Menus are rotated 90°. Menus are shown in a readable orientation for
projectors installed in portrait orientation (90° clockwise or
counterclockwise).
• To determine the orientation of menu rotation, projector orientation is detected
immediately after startup or when this setting is switched to [Auto].
• Menus are not rotated automatically in response to changes in projector orientation
during projection.
Guide
As you use the projector, messages are shown as guidance to introduce features and
operation.
Option
Function
Off
Hides the guide screen.
On
Shows the guide screen.
The guide screen is shown at the following cases.
• No input signal is detected.
• An invalid button is pressed in [BLANK] or [FREEZE] mode. (P34)
• When positional lock (P107) is set to [On] and buttons locked by this feature are
pressed.
Show input status
Shows input signal status when there is no signal, or when you are completing signal settings.
Option
Function
Off
The input status is not displayed.
On
The input status is displayed.
Air filter warning display
Shows a warning to replace the air filter when replacement is required.
Option
Function
Off
The air filter warning is not displayed.
On
The air filter warning is displayed.
Setting [Air filter warning display] to [Off] will disable display of the warning to replace
the air filter. We recommend checking the air filter counter (P133) occasionally to
know when to replace the filter.
120
Menu Settings
Overheat warning display
Shows a warning icon when the internal temperature is high and the projector may overheat.
Option
Function
Off
Disable high temperature warning icon display.
On
Enable high temperature warning icon display.
Remote control/Side control
> [System settings] > [Remote control/Side control]
Specify which operations are available using buttons on the remote control or in the
projector’s side controls.
Beep
You can select whether a beep sounds or not when you operate the projector.
Function
Off
Disables the beep.
On
Enables the beep.
The beep will not sound if you mute the projector sound with the MUTE button on the
remote control.
Key repeat enables projector or remote control buttons to be held down instead of pressing
them repeatedly.
Option
Function
Off
Key repeat is not enabled.
On
Key repeat is enabled.
Key lock
Lock the projector or remote (wireless) to prevent operation.
Option
Function
Off
Disables key lock. Operation is possible on the main unit or from the
remote control.
Main unit
Operation is not possible using the main unit.
Use the remote control.
Remote (wireless)
Disables infrared remote control operations (P36). Use buttons on the
main unit.
Operation is also possible with a wired remote control.
121
Menu Settings
Key repeat
Advanced Guide
Option
Menu Settings
To Unlock Key Lock Function
Turn off the projector and unplug the power plug. Hold down the OK button on the main unit
and plug in the power cord, as you continue to hold down the OK button. In a moment, a
beep will sound, and the controls will be unlocked.
When you access this setting from the projector’s side controls, [Main unit] is not
available. Similarly, when you access the setting from the remote control, [Remote
(wireless)] is not available.
Remote control channel
Separate channels can be assigned to up to four projectors so that a single remote control
can be used with each projector.
Selecting the Projector Channel
If a wired remote control is used, there is no need to set the remote control channel.
Option
Function
Ch1
Ch2
Ch3
Select the remote control channel to use with this projector.
Ch4
Independent
Can be controlled from a remote control set to any channel.
Selecting a Channel on the Remote Control
After changing the projector channel from the menu, always change the remote control
channel accordingly.
Ch1
Hold down both the Ch button and [1] button for 3 seconds.
Ch2
Hold down both the Ch button and [2] button for 3 seconds.
Ch3
Hold down both the Ch button and [3] button for 3 seconds.
Ch4
Hold down both the Ch button and [4] button for 3 seconds.
Independent
Hold down both the Ch button and [0] button for 3 seconds.
122
Menu Settings
Audio in terminal select
> [System settings] > [Audio in terminal select]
Select the terminal for audio input used with various input signals.
Submenu
Function
Select the terminal for audio input.
DVI-1
DVI-2
Option
Function
DVI-3
Off
No audio is output.
DVI-4
Audio in
Use audio signals from AUDIO IN for audio
output.
HDMI-1
Only available when the submenu is [HDMI-1] or
[HDMI 1x2]. Audio signals from HDMI-1 are
output.
HDMI-2
Only available when the submenu is [HDMI-2] or
[HDMI 1x2]. Audio signals from HDMI-2 are
output.
HDMI-1
HDMI-2
DVI 1x2
DVI 2x2 / 1x4
HDMI 1x2
Serial communication
> [System settings] > [Serial communication]
Option
Function
Baud rate
Modulation rate, in bits per second.
Data bits
Number of bits of data.
Parity
Number of parity bits.
Stop bit
Option
Function
1
Sets the stop bit length to 1.
2
Sets the stop bit length to 2.
Power supply settings
> [System settings] > [Power supply settings]
Specify how power is managed at startup, in standby, and when no signal is
supplied.
123
Menu Settings
Stop bit length.
Advanced Guide
You can check setting values for the service port (CONTROL) used for serial
communication.
Menu Settings
Standby power setting
Specify network function operating status in standby mode.
Option
Function
Normal
All network functions are available when network functions are
enabled, including the web screen and PJLink.
Low-power
All network functions are available even in standby mode.
However, the projector may be less responsive than usual when some
functions are initially used.
• If [Low-power] is selected, some features may take a long time to access on the
network. For quicker access, select [Normal].
• [Standby power setting] is not available when [Quick startup] is set to [On].
• [Standby power setting] is set to [Normal] and cannot be changed when scheduling
is enabled (P129).
• [Standby power setting] is set to [Normal] and cannot be changed when wireless
LAN is enabled (P136).
Quick startup
Enable faster startup next time by leaving some circuits on for 90 minutes after the projector
is turned off. However, to avoid sudden surges in intensity, projection is delayed by at least
approximately 1.7 seconds.
Option
Function
Off
Disable quick startup.
On
Enable quick startup.
Power management mode
Specify to turn the light source off or enter standby if there is no input signal. This feature
automatically turns off the light source or power after a certain period if the remote control or
projector is not operated.
Option
Function
Disabled
Disable power management mode.
Light source off
Only turns the light source off.
Standby
Turns the projector off and puts it in standby.
• Projection resumes when the same input signal is restored, when the remote control
or projector is operated, or when user commands are sent to turn the projector on.
• After the projector enters standby, restoring projection requires the same steps as
when turning the projector on normally.
• When [Disabled] is selected, [Direct power on] is not available.
124
Menu Settings
Power management duration
Specify how much time must pass before the light source goes off or the projector enters
standby mode, depending on the [Power management mode] setting.
Option
5 min. - 60 min.
Function
After 30 seconds without an input signal when the projector is idle, the
projector starts displaying a countdown of the selected time.
• If conditions that would start countdown are met while you are blanking projection,
blanking is canceled.
• Once countdown begins, audio output stops.
Direct power on
You can turn on the projector by connecting the power cable without pressing the POWER
button.
Option
Function
Off
The POWER button must be pressed to turn the projector on.
On
You can turn on the projector by connecting the power cable only.
Before enabling direct power on, be sure to set [Power management mode] to an
option other than [Disabled]. When [Disabled] is selected, [Direct power on] is not
available.
> [System settings] > [Motion blur reduction]
Motion blur is blurring that occurs during video playback. Motion blur reduction can
make this blurring less noticeable.
Function
Off
Motion blur reduction is not performed.
Weak
Reduce motion blur for fast-moving images. Note that images may
be slightly darker, and flickering may occur.
Strong
Reduce motion blur for images moving faster than with [Weak].
Note that images may be darker, and flickering may occur.
• If setting the projector to [Strong] or [Weak] produces distracting flickering, set it to [Off].
• [Motion blur reduction] is not available in [DICOM SIM] image mode. The menu is
grayed out.
125
Menu Settings
Option
Advanced Guide
Motion blur reduction
Menu Settings
Language
> [System settings] > [Language]
Select the menu display language.
Language
English
Russian
Czech
German
Dutch
Danish
French
Finnish
Arabic
Italian
Norwegian
Chinese (Simplified)
Spanish
Turkish
Chinese (Traditional)
Portuguese
Polish
Korean
Swedish
Hungarian
Japanese
126
Menu Settings
Other settings
> [System settings] > [Other settings]
Register a password, set a password, reset the air filter counter, schedule
operation, and access other settings and information.
Password settings
Disables the projector unless the correct password is entered.
Option
Function
The projector can be used even if no password is entered.
On
The projector cannot be used unless you enter your password.
To Cancel the Password
Turn off the projector and unplug the power plug.
Hold down the MENU button on the side control and connect the power
plug. Make sure to keep holding down the MENU button until a beep
sounds. When the projector beeps, the password is canceled. (The
entered password is also reset.)
Cancellation
To forcibly cancel the password from the remote control, in standby state
on the Remote
press the MENU button 3 times, then press the POWER button.
Control
• You cannot set [On] unless you have completed [Register password].
Once you set a password, the password entry screen appears at power-on.
Enter a 4 digit password.
Enter the password using the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the
remote control.
If the password is valid, the projection starts. If you enter a wrong password three times,
the power will be turned off.
• The projector also goes off after 3 minutes of inactivity on the password input
screen.
127
Menu Settings
Cancellation
on the
Projector
Advanced Guide
Off
Menu Settings
Register password
You can register a password for starting projection.
Enter a 4 digit password.
Enter the password using the pointer buttons [ ] (1) / [ ] (2) / [ ] (3) / [ ] (4) or the number
buttons on the remote control.
The 4-digit password is entered from the left to right digits. When the final digit is entered, the
password is automatically registered.
Press the MENU button to abort the registration.
Date and time settings
Set time settings such as the current date and time, date/time display format, daylight saving
time, and time zone.
Submenu
Function
Set the date and time. The date and time currently set are shown and
updated each second.
Fields are blank unless the real-time clock has been set.
Submenu
Date and time
Function
Date
Enter the date.
Time
Enter the time.
Enter
Confirms your entered values. Completing this setting
activates the real-time clock.
• The date/time display format is set in [Date display format].
• Settings may be reset if the projector is left unplugged for an
extended period.
Date display
format
Choose [Year/month/date], [Month/date/year], or [Date/month/year] as
the date display format shown for the date and time, in schedules, and
elsewhere.
Adjusts the time one hour ahead at the beginning of daylight saving
time and one hour back at the end. The timing of daylight saving time
must be set in advance.
Option
Daylight saving
time
Function
Off
Disable daylight saving time.
On
Enable daylight saving time.
Edit
Edit when daylight saving time starts and ends. Set
the month, day, and time on the editing screen shown
next for the starting and ending date/time.
[On] in [Daylight saving time] is not available until the starting
and ending timing are set.
Region
Select a city in the time zone where the projector is installed.
The time zone of the city selected in [Time zone] is shown.
128
Menu Settings
Submenu
Function
Select whether to sync the time on the projector using SNTP (Simple
Network Time Protocol).
Submenu
SNTP
Function
On (IPv4)
Use SNTP over an IPv4 connection.
On (IPv6)
Use SNTP over an IPv6 connection.
Off
Disable SNTP.
• [SNTP] is not available when [Network (wired/wireless)] is set
to [Off/Off].
• Use the web screen to set the IP address of the SNTP server.
[SNTP] is not available unless the SNTP server IP address
has been set.
Schedule
Some projector tasks can be automated by scheduling them. As the timing of scheduled
tasks, choose from [Default], which is not during a certain period, or one of five special period
times that you set up.
Advanced Guide
Option
Function
Default
Set a general schedule that is not during a specific period.
Special period 1-5
Set up to five specific periods to schedule operation.
• [On] is grayed out until you set the period in [Special period 1] to [Special period 5].
• Setting any schedule to [On] changes [Standby power setting] (P124) to [Normal].
• Tasks scheduled under the [Default] setting are not executed while special period
schedules are in effect.
129
Menu Settings
The [Period] setting of a special period cannot be set to overlap with another period.
Menu Settings
Detailed schedule setting
Option
Function
Off
Disable the schedule.
On
Enable the schedule.
Edit the schedule.
■ Default
Edit
130
Menu Settings
Option
Function
■ Special period
Submenu
Function
Period
Edit the period (start and end dates) for scheduled
operation. Note that no [Period] setting is used for the
[Default] schedule.
Day of week
Change the day of the week to edit.
Edit schedule
131
Menu Settings
Edit the tasks scheduled for your selected [Day of
week]. You can set or remove listed times, operations,
and parameters (POWER ON/OFF, INPUT,
CALIBRATION).
Advanced Guide
Edit
Select a day in [Day of week], and select the times, operations, and
parameters.
Light source calibration can also be scheduled during your specified
period, by selecting CALIBRATION. (For details, see page 132.)
However, the projector must project for at least 30 minutes before
calibration, so it must be turned on in advance.
Menu Settings
Option
Function
Submenu
Reset
Function
Clears setting details for the selected schedule.
Setting details for [Period] and day of the week are
reset.
Copy the tasks scheduled for your selected [Day of
week] to another day in the schedule copying menu.
Edit
Copy
schedule to
different day
Calibration
Calibration adjusts the projector to compensate for changes in image quality from long-term
use or differences in the environment of use.
Submenu
Function
Restore the original gamma if, after the projector has been used for
some time, you notice that tone curves have changed, or if neutral
colors have become tinted. Gamma restore can only be used after
about 30 minutes of projection.
Option
Gamma restore
Function
Off
Returns to the factory default without performing
Gamma restore.
Adjust
Restore the original gamma and apply the result.
• Restoring gamma will restore tone curves and neutral colors as
closely as possible to defaults, but original projection cannot be
matched exactly.
• If Gamma restore is performed, the adjustment screen will be
projected for approximately 8 minutes.
• To stop Gamma restore, press the POWER or EXIT button.
Cancellation will return the setting to [Off].
132
Menu Settings
Submenu
Adjust panel
temperature
Function
Used when the gamma has changed in response to other changes,
such as changes in ambient temperature.
Compensates for changes in gradation caused by a change in LCOS
panel temperature. This function can only be used after about 2 minutes
of projection.
Option
Function
Off
Do not adjust the panels to suit the temperature.
Adjust
Adjust the panels to suit the temperature.
Use when there is concern about deterioration of the color and
luminance of the light source due to extended use.
Light source
calibration
Option
Function
OK
Execute light source calibration.
Cancel
Do not execute light source calibration.
Light source calibration can only be used after about 30 minutes of projection.
Trigger out
Option
Function
Off
No output from the trigger terminal.
Link with power
12 V of voltage output from the trigger terminal during projection. Used
to trigger operation of a screen or other external device in sync when
the projector is turned on or off.
This resets the counter which reminds you of the time for replacing the air filter.
Also used to reset the counter after air filter replacement.
For details on replacing the filter, see P194 - P196.
Power counter
Indicates the total time that the projector has been connected to a power supply.
This value is not reset even if [Factory defaults] is executed.
133
Menu Settings
Air filter counter
Advanced Guide
Operation of a screen or other external device can be triggered by turning the projector on or
off.
Menu Settings
Firmware
Update the projector firmware.
Check the version indicated before updating the firmware.
Update the projector firmware as follows.
1. Download updated firmware from the Canon website and store it at the root directory on a
USB flash drive.
2. Insert the USB flash drive in the USB port.
3. Follow the instructions shown to complete the update process.
• Firmware versions shown here are for illustration only and differ from actual
versions.
• In some cases, it may not be possible to download updates. For details, contact the
Canon Customer Support Center.
• Firmware updating takes a few minutes. During the update, the LED indicator will
flash in red. Do not turn off the projector while the LED is flashing. After the update,
the projector will automatically turn itself off and enter standby mode.
Factory defaults
You can reset the menu item settings and restore the system settings to the factory defaults.
Option
Function
OK
Settings are reset to default.
Cancel
Settings are not reset to default.
134
Menu Settings
Network settings
Network Connection Overview
Connecting the projector to a network enables you to control the projector from a
computer and receive notification of projector errors via email.
Depending on the method of network connection, preparation on the computer side
may be necessary. The following is an explanation of preparation on the computer
side.
Connection Methods
The projector can be connected to a wired network with a LAN cable or to a
wireless network via Wi-Fi.
Wired Networks
To connect the projector to a computer network, use a LAN cable.
LAN cable (shielded twisted pair;
not included)
LAN port
Advanced Guide
Hub or router, etc.
Menu Settings
135
Menu Settings
Wireless Networks
• Projector Access Point (PJ AP) Mode
The projector can be used as an access point for direct communication with
wireless LAN-compatible computers.
Up to five computers can be connected at once.
Projector (in PJ AP mode)
Wireless LAN-compatible
computers
The following network features are available in PJ AP mode.
• Web features
• User commands
Other network features (specifically, SNMP, PJLink, Mail, AMX and Crestron RoomView)
are not available.
• Infrastructure Mode
The projector can also be used as a wireless LAN client for connections to a
wireless LAN access point.
In this case, the projector is connected to computers via the wireless LAN access
point.
Wireless
LAN-compatible
computers
Projector
(in infrastructure mode)
Access point
Computers
connected to the
network via LAN
cable
136
Menu Settings
• The following network features are available in infrastructure mode.
- Web features
- Mail features
- User commands
Other network features (specifically, SNMP, PJLink, AMX and Crestron RoomView) are
not available.
• The following restrictions apply in infrastructure mode.
- Access point SSIDs not in ASCII code (single-byte letters, numbers, or symbols)
may cause character corruption in search result display.
- Connectivity cannot be assured if access point SSIDs include characters not in
ASCII code (single-byte letters, numbers, or symbols).
When multiple access points have the same SSID, only search results for the access
point with the strongest signal are shown.
•
•
•
•
137
Menu Settings
Before connecting to a network environment that uses a DHCP server, set [DHCP] in the
menu to [On] to enable the DHCP function. (P143, P149)
Advanced Guide
Wired LAN features and infrastructure mode cannot be used at the same time.
PJ AP and infrastructure modes cannot be used at the same time.
Wired LAN and PJ AP mode cannot be used in the same subnetwork.
Remember to set your preferred network (wired or wireless) to [On] if [Network
(wired/wireless)] on the projector is set to [Off/Off] and the network connection is
disabled. (P142) For wireless networks, choose the type of connection.
• Referring to “Checking Projector Information” (P155), confirm that the projector’s
wired or wireless IP address is not the same as that of other computers on the
network. To set a projector IP address, follow the instructions in “Completing
Computer Settings for a Network Connection” (P156) and use the web screen, or
use projector TCP/IP settings. (P144, P149)
• When you connect the computer to the network for the first time, it is also
necessary to perform settings on the computer. In this case, consult the network
administrator regarding the necessary settings.
Menu Settings
Wireless LAN (Wi-Fi)
■ Countries and Regions Where Wireless LAN Use Is
Permitted
Use of the wireless LAN function is restricted under the laws, etc., of each country
and region, and violation of these restrictions may be subject to punishment. Check
the Canon website for a list of countries and regions where use of the wireless LAN
function permitted.
Canon assumes no responsibility whatsoever for problems, etc., that may arise
from use of the wireless LAN function in countries and regions other than those
listed.
■ Model Number
4K600STZ (including WLAN module model: CH9-1346)
Complies with
IDA Standards
DB00671
FCC/IC NOTICE
Model: 4K600STZ (including WLAN Module Model CH9-1346,
FCC ID: AZD221)
This device complies with Part 15 of FCC Rules and Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1)
this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of this
device.
This transmitter must not be co-located or operated in conjunction with any other
antenna or transmitter except Canon accessories supplied or designated for this
product.
This equipment complies with FCC/IC radiation exposure limits set forth for an
uncontrolled environment and meets the FCC radio frequency (RF) Exposure
Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This
equipment should be installed and operated keeping the radiator at least 20cm or
more away from person’s body.
138
Menu Settings
Statement on EC directive
139
Menu Settings
Please contact the following address for the original Declaration of Conformity:
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
Advanced Guide
Canon Inc. tímto prohlašuje, že tento CH9-1346 je ve shodě se základními požadavky a
dalšími příslušnými ustanoveními směrnice 1999/5/ES.
Undertegnede Canon Inc. erklærer herved, at følgende udstyr CH9-1346 overholder de
væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF.
Hiermit erklärt Canon Inc., dass sich das Gerät CH9-1346 in Übereinstimmung mit den grundlegenden
Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet.
Käesolevaga kinnitab Canon Inc. seadme CH9-1346 vastavust direktiivi 1999/5/EÜ
põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele.
Hereby, Canon Inc., declares that this CH9-1346 is in compliance with the essential
requirements and other relevant provisions of Directive 1999/5/EC.
Por medio de la presente Canon Inc. declara que el CH9-1346 cumple con los requisitos
esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ Canon Inc. ΔΗΛΩΝΕΙ ΟΤΙ CH9-1346 ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ
ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ.
Par la présente Canon Inc. déclare que l’appareil CH9-1346 est conforme aux exigences
essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE.
Con la presente Canon Inc. dichiara che questo CH9-1346 è conforme ai requisiti essenziali
ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE.
Ar šo Canon Inc. deklarē, ka CH9-1346 atbilst Direktīvas 1999/5/EK būtiskajām prasībām un
citiem ar to saistītajiem noteikumiem.
Šiuo Canon Inc. deklaruoja, kad šis CH9-1346 atitinka esminius reikalavimus ir kitas
1999/5/EB Direktyvos nuostatas.
Hierbij verklaart Canon Inc. dat het toestel CH9-1346 in overeenstemming is met de
essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG.
Hawnhekk, Canon Inc., jiddikjara li dan CH9-1346 jikkonforma mal-ħtiġijiet essenzjali u ma
provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC.
Alulírott, Canon Inc. nyilatkozom, hogy a CH9-1346 megfelel a vonatkozó alapvetõ
követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak.
Niniejszym Canon Inc. oświadcza, że CH9-1346 jest zgodny z zasadniczymi wymogami oraz
pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC.
Canon Inc. declara que este CH9-1346 está conforme com os requisitos essenciais e outras
disposições da Directiva 1999/5/CE.
Canon Inc. izjavlja, da je ta CH9-1346 v skladu z bistvenimi zahtevami in ostalimi relevantnimi
določili direktive 1999/5/ES.
Canon Inc. týmto vyhlasuje, že CH9-1346 spĺňa základné požiadavky a všetky príslušné
ustanovenia Smernice 1999/5/ES.
Canon Inc. vakuuttaa täten että CH9-1346 tyyppinen laite on direktiivin 1999/5/EY oleellisten
vaatimusten ja sitä koskevien direktiivin muiden ehtojen mukainen.
Härmed intygar Canon Inc. att denna CH9-1346 står I överensstämmelse med de väsentliga
egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
Hér með lýsir Canon Inc. yfir því að CH9-1346 er í samræmi við grunnkröfur og aðrar kröfur,
sem gerðar eru í tilskipun 1999/5/EC.
Canon Inc. erklærer herved at utstyret CH9-1346 er i samsvar med de grunnleggende krav og
øvrige relevante krav i direktiv 1999/5/EF.
С настоящия документ Canon Inc. декларира, че CH9-1346 е в съгласие с основните
изисквания и съответните постановления на Директива 1999/5/ЕС.
Prin prezenta, Canon Inc. declară că acest CH9-1346 este conform cu cerinţele principale şi
cu celelalte prevederi relevante ale Directivei 1999/5/EC.
Menu Settings
Completing Projector Settings
Settings described in this section apply to wired and wireless network
connections, setting a network password, and other aspects of networked
projection.
(When the input signal is HDMI-1)
Menu
Function
Details
Network settings lock
Lock network settings to prevent changes.
P141
Network password
setting
Specify whether network settings are passwordprotected.
P141
Register network
password
Set a network password.
P141
Network (wired/wireless)
Enable or disable wired or wireless network
connectivity and the mode of operation.
P142
Detailed settings (wired)
Display and set advanced settings for wired
connections.
P142
Detailed settings
(wireless)
Display and set advanced settings for wireless
connections.
P147
PJLink*
Enable or disable PJLink.
P152
AMX Device Discovery*
Enable or disable AMX Device Discovery.
P153
Crestron RoomView*
Enable or disable Crestron RoomView.
P153
Information
Display network information.
P154
*Only available for wired connections.
140
Menu Settings
Network settings lock
> [Network Settings] > [Network settings lock]
You can lock/unlock the network settings so that they cannot be changed.
Option
Function
Unlock
Cancels the lock and allows other network settings to be changed. The
password must be entered in order to cancel the lock. Use the [ ] / [ ] /
[ ] / [ ] buttons or number buttons on the remote control to enter the
four-digit network password.
Lock
Lock the settings.
Forcibly canceling the network lock
Press these buttons in the following order to cancel the lock: [ ] [OK] [ ] [OK] [
This operation resets the network password to [ ] [ ] [ ] [ ] ([1] [1] [1] [1]).
Setting [Network password setting] to [Off] leaves network settings unlocked.
] [OK].
Network password setting
> [Network settings] > [Network password setting]
Option
Function
Off
A network password is not used.
On
A network password is used.
Advanced Guide
You can set whether or not a password is required in order to change the projector
network settings.
Register network password
Use the [ ] / [ ] / [ ] / [ ] buttons or number buttons on the remote control to enter
the projector network password.
141
Menu Settings
> [Network settings] > [Register network password]
Menu Settings
Network (wired/wireless)
> [Network settings] > [Network (wired/wireless)]
Enable or disable wired or wireless network connectivity and the mode of operation.
Specifying [Off] can save energy.
Option
Function
Off/Off
Disables the network function.
On/Off
Enable only wired networking.
On/On (Pj AP)
Enable both wired and wireless (PJ AP mode) networking.
Off/On (Pj AP)
Enable only wireless (PJ AP mode) networking.
Off/On (Infra)
Enable only wireless (infrastructure mode) networking.
Notes When Connected Wirelessly
• A message is displayed at the initial startup in PJ AP mode (P136) requesting that you
check security key settings.
Detailed settings (wired)
> [Network settings] > [Detailed settings (wired)]
Display and manually change the wired IP address, gateway address, and other
settings. Available only when wired networking is [On].
Menu
MAC address
Function
Wired MAC address of the projector.
142
Menu Settings
Menu
Function
Configure details of the projector’s wired LAN (IPv4) function.
Submenu
Detailed IPv4
address settings
Function
IP address
IP address of the wired LAN (IPv4).
Subnet mask
Subnet mask of the wired LAN (IPv4).
Gateway
address
Gateway address of the wired LAN (IPv4).
Option
Function
Disables the DHCP function. TCP/IP
settings can be configured manually.
On
Enables the DHCP function. Searches
the DHCP server. It will no longer be
possible to enter the IP address, subnet
mask, or gateway address manually,
because the IP address is acquired from
the DHCP server.
DHCP
Advanced Guide
Off
Menu Settings
143
Menu Settings
Menu
Function
Submenu
Function
Change or specify the IP address, subnet mask, and
gateway address used for connections.
Detailed IPv4
address settings
TCP/IP
settings
• This menu is not available (grayed out)
when [DHCP] (P143) is [On].
• If an invalid value is entered, “Invalid entry.”
is displayed. In this case, enter a valid
value.
• When [Network (wired/wireless)] is set to
[On/On (Pj AP)], “Cannot set identical
segment IP” is displayed if you specify the
same subnetwork as in PJ AP mode. Enter
a different subnetwork, or change [Network
(wired/wireless)] to [On/Off] before entering
the wired IP address again.
Option
IPv6
Function
Off
Disables the projector’s wired LAN (IPv6) function.
On
Enables the projector’s wired LAN (IPv6) function.
[Detailed IPv6 address settings] is now available.
144
Menu Settings
Menu
Function
Configure details of the projector’s wired LAN (IPv6) function.
Submenu
Detailed IPv6
address settings
Function
Link-local address of the wired LAN (IPv6).
Auto
Automatic addresses (up to 5) of the wired LAN (IPv6).
Manual
Manual address of the wired LAN (IPv6).
Gateway
Gateway address of the wired LAN (IPv6).
Auto settings
Enable/disable automatic address setting of the wired
LAN (IPv6).
Manually configure settings of the wired LAN (IPv6).
Change or specify the IPv6 address, prefix length, and
gateway address.
• This menu is not available (grayed out)
when [Auto settings] is [On].
• If an invalid value is entered, “Invalid entry.”
is displayed. In this case, enter a valid
value.
145
Menu Settings
Manual
settings
Advanced Guide
Link local
Menu Settings
Menu
Network setting
initialization
Function
The following network settings are initialized.
Settings configured from the projector menu
• Network settings lock (P141)
• Network password setting (P141)
• Register network password (P141)
• Network (wired/wireless) (P142)
• Detailed settings (wired) (P142)
- Detailed IPv4 address settings (P143)
- IP address (wired LAN (IPv4)) (P143)
- Subnet mask (wired LAN (IPv4)) (P143)
- Gateway address (wired LAN (IPv4)) (P143)
- DHCP (wired LAN (IPv4)) (P143)
- TCP/IP settings (P144)
- IPv6 (P144)
- Detailed IPv6 address settings (P145)
- Auto settings (P145)
- Manual settings (P145)
- IP address (wired LAN (IPv6)) (P145)
- Prefix length (P145)
- Gateway address (wired LAN (IPv6)) (P145)
• PJLink (P152)
• AMX Device Discovery settings (P153)
• Crestron RoomView settings (P153)
Settings configured from the web screen
• [Password] (P163)
• [Wired] (P170)
- DHCP (P170)
- IP address (P170)
- Subnet mask (P170)
- Default gateway (P170)
• [Mail] (P174)
• [SNMP] (P176)
• [Projector info.] (P177)
• [PJLink] (P177)
• [Crestron] (P178)
146
Menu Settings
Detailed settings (wireless)
> [Network settings] > [Detailed settings (wireless)]
Display and manually change the wireless IP address, gateway address, and other
settings. Available only when wireless networking is [On].
Menu
Function
Shows the wireless connection mode. (P136)
SSID
Shows the access point SSID.
Security
Shows the security setting.
Channel
Shows the channel used for the connection.
Signal strength
Shows actual signal strength, as measured.
MAC address
Wireless MAC address of the projector.
Select the method of connection in infrastructure mode.
Function
PBC
Connect in PBC (push-button) mode.
Following the instructions shown, press the button on
the wireless base station (access point), and, within
2 minutes, select [OK] on the screen.
PIN
Connect in PIN mode.
Following the instructions shown, enter the displayed
8-digit PIN code on the wireless base station (access
point), and, within 10 minutes, select [OK] on the
screen.
Wi-Fi Protected
Setup
147
Menu Settings
Submenu
Advanced Guide
Mode
Menu Settings
Menu
Function
Manually specify the projector’s wireless settings.
Submenu
Mode
Function
Shows the wireless connection mode. (P136)
A list of available access point SSIDs is displayed.
You can find available access points nearby and
change the name of the connection.
Manual settings
SSID
Security
Select the wireless security from [Open], [WEP],
[WPA2 AES], or [WPA/WPA2 TKIP/AES]. In PJ AP
mode, choose from [Open] or [WPA2 AES].
Channel
Shows the current wireless channel (1 - 11).
Key ID
Select the wireless WEP key ID. Only available for
when security is set to [WEP].
Key type
Select the wireless security key input type. Not
available when security is set to [Open].
Key
Not available when security is set to [Open] or when
wired/wireless networking is set to [On/On (Pj AP)] or
[Off/On (Pj AP)].
Apply
Connect with the current settings.
148
Menu Settings
Menu
Function
Configure details of the projector’s wireless LAN (IPv4) function.
Submenu
Function
IP address
IP address of the projector’s wireless LAN (IPv4).
Subnet mask
Subnet mask of the projector’s wireless LAN (IPv4).
Gateway
address
Gateway address of the projector’s wireless LAN
(IPv4).
Enable or disable wireless DHCP on the projector.
Option
Off
On
Enables the DHCP function. Searches
the DHCP server. It will no longer be
possible to enter the IP address, subnet
mask, or gateway address manually,
because the IP address is acquired from
the DHCP server.
DHCP
Configure the projector’s wireless TCP/IP settings.
TCP/IP
settings
Option
IPv6
Function
Off
Disables the projector’s wireless LAN (IPv6) function.
On
Enables the projector’s wireless LAN (IPv6) function.
[Detailed IPv6 address settings] is now available.
149
Menu Settings
• This menu is not available (grayed out)
when [DHCP] is [On].
• If an invalid value is entered, “Invalid entry.”
is displayed. In this case, enter a valid
value.
Advanced Guide
Detailed IPv4
address settings
Function
Disables the DHCP function. TCP/IP
settings can be configured manually.
Menu Settings
Menu
Function
Configure details of the projector’s wireless LAN (IPv6) function.
Submenu
Detailed IPv6
address settings
Function
Link local
Link-local address of the wireless LAN (IPv6).
Auto
Automatic addresses (up to 5) of the wireless LAN
(IPv6).
Manual
Manual address of the wireless LAN (IPv6).
Gateway
Gateway address of the wireless LAN (IPv6).
Auto settings
Enable/disable automatic address setting of the
wireless LAN (IPv6).
Manually configure settings of the wireless LAN
(IPv6). Change or specify the IPv6 address, prefix
length, and gateway address.
Manual
settings
• This menu is not available (grayed out)
when [Auto settings] is [On].
• If an invalid value is entered, “Invalid entry.”
is displayed. In this case, enter a valid
value.
150
Menu Settings
Menu
Network setting
initialization
Function
Advanced Guide
The following network settings are initialized.
Settings configured from the projector menu
• Network settings lock (P141)
• Network password setting (P141)
• Register network password (P141)
• Network (wired/wireless) (P142)
• Detailed settings (wireless) (P147)
- Detailed IPv4 address settings (P149)
- TCP/IP settings (P149)
- IP address (wireless LAN (IPv4)) (P149)
- Subnet mask (wireless LAN (IPv4)) (P149)
- Gateway address (wireless LAN (IPv4)) (P149)
- DHCP (wireless LAN (IPv4)) (P149)
- IPv6 (P149)
- Detailed IPv6 address settings (P150)
- Auto settings (P150)
- Manual settings (P150)
- IP address (wireless LAN (IPv6)) (P150)
- Prefix length (P150)
- Gateway address (wireless LAN (IPv6)) (P150)
Settings configured from the web screen
• [Password] (P163)
• [Wireless] (P172)
- DHCP (P172)
- IP address (P172)
- Subnet mask (P172)
- Default gateway (P172)
• [Mail] (P174)
• [Mail auth] (P175)
• [Projector info.] (P177)
Menu Settings
151
Menu Settings
PJLink
> [Network settings] > [PJLink]
You can enable or disable the PJLink network function of the projector.
When the function is turned on, control is possible via the network using commands
that meet PJLink standards.
Option
Function
Off
Disables the PJLink function.
On
Enables the PJLink function.
• The projector conforms to Class 1 as defined in PJLink standards established by the
Japan Business Machine and Information System Industries Association (JBMIA). This
projector supports all commands that are defined by PJLink Class 1, and has been
verified as conforming to the PJLink standard Class 1 definition.
• For details on using PJLink, see “Setting PJLink [PJLink]” (P177).
What is PJLink?
In September 2003, the PJLink Working Group was established under the Data Projector
Committee. During the first year, this PJLink Working Group standardized PJLink as a new
interface specification for projectors.
PJLink is a unified standard for operation and control of projectors.
It allows centralized control of projectors and operation from a controller for all projectors
regardless of manufacturer.
The objective is for JBMIA to improve convenience for users and expand the use of
projectors through early systemization for network monitoring and control of projectors,
which will become the mainstream in the future.
Class 1: Standardization of control and monitoring specifications for basic projector
functions
Basic projector control: Power control, input selection, etc.
Acquisition of projector information and status: Power status, input selection status, error
status, etc.
JBMIA: Japan Business Machine and Information System Industries Association.
The JBMIA is an organization which was launched in 1960 and changed its name
on April 1, 2002.
PJLink website: http://pjlink.jbmia.or.jp/english/
PJLink is a registered trademark of JBMIA and pending trademark in some countries.
PJLink is a registered trademark, or an application has been submitted for trademark, in Japan,
the United States and / or other countries or regions.
152
Menu Settings
AMX Device Discovery
> [Network settings] > [AMX Device Discovery]
This setting enables other equipment compatible with AMX Device Discovery to
detect the projector over a network. For networks without AMX Device Discovery,
select [Off].
Option
Function
Off
Disables AMX Device Discovery.
On
Enables AMX Device Discovery. The projector will periodically send
out AMX beacon packets over the network.
• For details on AMX Device Discovery, visit the AMX website.
http://www.amx.com/
Crestron RoomView
> [Network settings] > [Crestron RoomView]
Option
Function
Off
Disable Crestron RoomView.
On
Enables Crestron RoomView. A port for RoomView will be opened,
and the projector will respond to CIP packets. Communication is
possible via the RoomView Express/Server application or via
Crestron Controller. (P178)
153
Menu Settings
• For details on Crestron RoomView, visit the Crestron® website.
http://www.crestron.com/
Advanced Guide
Crestron RoomView enables centralized management of multiple projectors over a
network. Networked projectors can be remotely controlled to troubleshoot issues,
or turn the projectors on or off. Specify whether to use Crestron RoomView.
Menu Settings
Information
> [Network settings] > [Information]
Shows network information.
Menu
Function
E-mail sender address
Sender e-mail address for sending error messages. (P174)
E-mail recipient address
[Already set] or [Not set] is shown, indicating whether a
recipient e-mail address has been set for error messages.
(P174)
IPv4
Detailed
information
(wired)
IP address of the wired LAN (IPv4).
Link local Link-local IP address of the wired LAN (IPv6).
IPv6
Auto
Automatic IP address of the wired LAN (IPv6).
Manual
Manual IP address of the wired LAN (IPv6).
IPv4
Detailed
information
(wireless)
IP address of the wireless LAN (IPv4).
Link local Link-local IP address of the wireless LAN (IPv6).
IPv6
Auto
Automatic IP address of the wireless LAN (IPv6).
Manual
Manual IP address of the wireless LAN (IPv6).
• Detailed information (wired) is displayed when [Network (wired/wireless)] is set to
[On/*].
• Detailed information (wireless) is displayed when [Network (wired/wireless)] is set to
[*/On].
154
Menu Settings
Checking Projector Information
You can check information about the signal types of the images projected
and other information.
Menu
Function
Input signal
Details of the input signal currently selected
Information such as the type, resolution, frequency, and color
format of the signal is displayed.
Firmware
Current firmware version
Serial no.
Serial number unique to this projector
Projector usage time
Shows the total time the projector has been on.
IP address (wired)*
IP address for wired connections.
IP address (wireless)*
IP address for wireless connections.
Projector name*
Name which identifies this projector on the network
Comments*
Comments such as the location in which the projector is installed
are displayed. (P177)
System information ID
System information. Normally this is not displayed.
* No value is displayed when [Network (wired/wireless)] is set to [Off/Off].
Some values may not be displayed, depending on [Network (wired/wireless)]
settings. ( : displayed, ×: not displayed)
Network
(wired/wireless)
Off/Off
IP address (wired)
×
IP address (wireless)
×
Projector name
×
Comments
×
On/Off
×
155
On/On
(Pj AP)
Off/On
(Pj AP)
Off/On
(Infra)
×
×
Menu Settings
Shows the model name.
Advanced Guide
Model name
Using the Projector on a Network
Completing Computer Settings for a Network
Connection
Specifying an IP Address
Instructions for setting a computer’s IP address (for wired connections or wireless
connections) are as follows for each operating system.
■ Windows 10
1
Right-click the Start button (Windows logo) in the lower left of the screen.
• In desktop mode (from the desktop screen)
The same operation is possible by pressing Win+X.
2
3
In the shortcut menu displayed in the lower left, click [Control Panel].
Click [View network status and tasks].
• In Icon View:
Click [Network and Sharing Center].
4
5
Click [Change adapter settings].
6
In the [This connection uses the following items] list, select [Internet
Protocol Version 4 (TCP/IPv4)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default
gateway, etc).
7
Select [Use the following IP address] and set the IP address and subnet
mask.
The projector’s own default IP address is “192.168.254.254” for wired
connections and “192.168.253.254” for wireless connections. Specify a
different IP address.
8
When finished, click the [OK] button, and then click the [Close] button in
the [Ethernet Properties] window to close it.
For a wired connection, right-click [Ethernet], or for a wireless
connection, right-click [Wi-Fi]. Next, click [Properties].
156
Using the Projector on a Network
■ Windows 8.1 / Windows 8
1
Right-click on the start screen background and click [All Apps] in the
lower right.
• Windows 8.1 Users:
Click the down arrow in the lower left of the start screen.
2
Click [Control Panel].
• From the Desktop:
Press Win+X.
In the shortcut menu displayed in the lower left, click [Control Panel].
3
Click [View network status and tasks].
• In Icon View:
Click [Network and Sharing Center].
4
5
Click [Change adapter settings].
6
In the [This connection uses the following items] list, select [Internet
Protocol Version 4 (TCP/IPv4)] and click the [Properties] button. Make a
note of the original network settings (IP address, subnet mask, default
gateway, etc).
7
Select [Use the following IP address] and set the IP address and subnet
mask.
The projector’s own default IP address is “192.168.254.254” for wired
connections and “192.168.253.254” for wireless connections. Specify a
different IP address.
8
When finished, click the [OK] button, and then click the [Close] button in
the [Ethernet Properties] window to close it.
For a wired connection, right-click [Ethernet], or for a wireless
connection, right-click [Wi-Fi]. Next, click [Properties].
Advanced Guide
Using the Projector on a Network
157
Using the Projector on a Network
■ Windows 7
1
2
From the PC [Start] menu, select [Control Panel].
3
From the menu on the left side of the window, click on [Change adapter
settings].
4
For a wired connection, right-click [Local Area Connection], or for a
wireless connection, right-click [Wireless Network Connection]. Next,
click [Properties].
5
Select [Internet Protocol Version 4 (TCP/IPv4)] and click the [Properties]
button. Make a note of the original network settings (IP address, subnet
mask, default gateway, etc).
6
Select [Use the following IP address] and set the IP address and subnet
mask.
The projector’s own default IP address is “192.168.254.254” for wired
connections and “192.168.253.254” for wireless connections. Specify a
different IP address.
7
When the settings are completed, click the [OK] button and then click the
[OK] button on the [Local Area Connection Properties] window to close it.
Click on [Network and Internet], then click on [View network status and
tasks].
■ Windows Vista
1
2
3
From the PC [Start] menu, select [Control Panel].
4
For a wired connection, right-click [Local Area Connection], or for a
wireless connection, right-click [Wireless Network Connection]. Next,
click [Properties].
5
Select [Internet Protocol Version 4 (TCP/IPv4)] and click the [Properties]
button. Make a note of the original network settings (IP address, subnet
mask, default gateway, etc).
6
Select [Use the following IP address] and set the IP address and subnet
mask.
The projector’s own default IP address is “192.168.254.254” for wired
connections and “192.168.253.254” for wireless connections. Specify a
different IP address.
7
When the settings are completed, click the [OK] button and then click the
[OK] button on the [Local Area Connection Properties] window to close it.
Click on [View network status and tasks].
From the menu on the left side of the window, click on [Manage network
connections].
158
Using the Projector on a Network
■ Mac OS X
1
2
Open the Apple Menu and select [System Preferences].
3
For a wired connection, select [Built-in Ethernet], or for a wireless
connection, select [Wi-Fi]. Next, click the [TCP/IP] tab. Make a note of the
original network settings (IP address, subnet mask, router, DNS server,
and so on).
4
Create a new network environment and set the IP address and subnet
mask.
The projector’s own default IP address is “192.168.254.254” for wired
connections and “192.168.253.254” for wireless connections. Specify a
different IP address.
5
Click [Apply] to close the network preference window.
In the System Preferences window, click [Network] to display the Network
window.
■ Resetting the IP Address Setting of the Computer
Follow the same procedure as for changing the IP address and reset the values to
the original values based on the notes taken before the change.
Advanced Guide
Using the Projector on a Network
159
Using the Projector on a Network
Setting Up the Network
■ Displaying the Network Configuration Screen
1
Turn on the computer and projector.
Network functions are not available for the first 40 seconds after projector startup.
2
Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
The following information is displayed.
Projector control
Displays the projector control screen.
Settings
Shows the settings screen.
Projector name
The name of the projector on the network
Comment
Relevant notes, such as where the projector is installed
MAC address (Wired)
MAC address of the wired LAN
IP address (Wired)
IP address of the wired LAN (IPv4)
MAC address (Wireless)
MAC address of the wireless LAN
IP address (Wireless)
IP address of the wireless LAN (IPv4)
Power status
The power status of the projector
Filter time
Air filter operating time
Alert
Error message (if an error has occurred)
Temperature abnormality
Light source abnormality
Faulty air filter unit
Faulty cooling fan
Faulty power supply
The factory default IP address is “192.168.254.254” for wired connections (IPv4) and
“192.168.253.254” for wireless connections (IPv4). If DHCP settings are used, ask the
network administrator for the projector IP address. It is possible to check the IP address
from the projector menu. (P143, P149)
3
Click [Settings] on the web screen.
The password input window appears.
160
Using the Projector on a Network
4
Enter the user name and password on the password input window, then
click [OK].
The factory default user name is “root” and the password is “system”.
The settings screen is displayed. Complete the network settings on this screen.
To control the projector from the computer, click [Projector control]. (P181)
■ Network Setting
1
Select a function to set up from the settings screen menu.
Advanced Guide
Using the Projector on a Network
161
Using the Projector on a Network
2
Enter setting details in the fields shown (1), and then click [OK] (2).
(1)
(2)
3
A confirmation window appears. Check the contents and if they are
correct, click [Apply].
162
Using the Projector on a Network
The settings are applied to the projector.
Selecting [Wired], [Wireless] or [Password] in the menu will cause this
message to be displayed: “Save completed. Please change setting and
reconnect.”
If you select functions other than above, “Save completed” is displayed. Click
[Back to top] to return to the top page of the web screen.
Setting a Password [Password]
From [Password] in the settings screen, you can set a user name and password for
web screen login. For the setting procedure, refer to “Network Setting” (P161).
Advanced Guide
Explanation
Factory default setting
When logging into the web screen,
enter the user name in 1-byte
alphanumeric characters and symbols
(4 -15 characters).
root
New password
When logging into the web screen,
enter the password in 1-byte
alphanumeric characters and symbols
(4 -15 characters).
system
Confirm new password
For confirmation, enter the same
password that you entered in [New
password].
system
163
Using the Projector on a Network
Item
User name
Using the Projector on a Network
Setting the Date and Time [Date and time settings]
From [Date and time settings] in the settings screen, you can set time settings such
as the current date and time, date/time display format, time zone, and daylight
saving time. For the setting procedure, refer to “Network Setting” (P161).
Item
Day &
Time
Explanation
Factory default setting
Day
Enter the date in 1-byte
numbers.
2017/01/01
Indication order
Choose [YYYY/MM/DD],
[MM/DD/YYYY], or [DD/MM/
YYYY] as the date display
format.
YYYY/MM/DD
Time
Enter the time in 1-byte
numbers, in the range
00:00:00 to 23:59:59.
00:00:00
Time zone
Select a city in your time
zone.
(GMT) Dublin, Lisbon,
London
SNTP
Select whether to turn the
SNTP (Simple Network Time
Protocol) function on or off.
Choosing ON (IPv4) will
prevent you from configuring
the following settings.
[Day]
[Time]
[IPv6 SNTP server IP
address]
Choosing ON (IPv6) will
prevent you from configuring
the following settings.
[Day]
[Time]
[IPv4 SNTP server IP
address]
OFF
164
Using the Projector on a Network
Item
Day &
Time
Explanation
Factory default setting
IPv4 SNTP
Enter the IPv4 SNTP server
0.0.0.0
server IP address IP address in 1-byte numbers.
IPv6 SNTP
Enter the IPv6 SNTP server
<Blank>
server IP address IP address in 1-byte numbers.
Summer
Time
OFF
Start point Month
Select the month when
daylight saving time begins.
1
Start point Week
Select the week when
daylight saving time beings.
1
Start point Day
Select the day when daylight
saving time begins.
Mon
Start point Time
Enter the starting time for
daylight saving time in 1-byte
numbers, in the range 00:00
to 23:59.
00:00
Finish point
Month
Select the month when
daylight saving time ends.
1
Finish point
Week
Select the week when
daylight saving time ends.
1
Finish point Day
Select the day when daylight
saving time ends.
Mon
Finish point Time
Enter the ending time for
daylight saving time in 1-byte
numbers, in the range 00:00
to 23:59.
00:00
165
Using the Projector on a Network
Select whether to turn on or
off time adjustment one hour
ahead at the beginning of
daylight saving time and one
hour back at the end.
Choosing OFF will prevent
you from configuring the
following settings.
[Start point Month]
[Start point Week]
[Start point Day]
[Start point Time]
[Finish point Month]
[Finish point Week]
[Finish point Day]
[Finish point Time]
Advanced Guide
ON / OFF
Using the Projector on a Network
Setting a Scheduling [Schedule]
From [Schedule] in the settings screen, you can automate some projector tasks by
scheduling them. As the timing of scheduled operation, choose from [Usually],
which is not during a certain period, or one of five special period times (Period.1 –
Period.5) that you set up. For the setting procedure, refer to “Network Setting”
(P161).
Item
Schedule
view
Explanation
Factory default setting
Select period
Select a specific period to
configure.
Period.1
Time setting
In the left box, enter the
starting date of the specific
period you are scheduling,
and in the right box, enter the
ending date, using 1-byte
numbers.
Dates of periods cannot be
set to overlap.
2017/01/01
Usually
Shows the usual schedule,
which can be turned on or off
by selecting the check boxes.
Cleared (OFF)
166
Using the Projector on a Network
Item
Schedule
view
Explanation
Factory default setting
Shows the timing of the
scheduled period 1. Can be
turned on or off by selecting
the check box.
Cleared (OFF)
Period.2
Shows the timing of the
scheduled period 2. Can be
turned on or off by selecting
the check box.
Cleared (OFF)
Period.3
Shows the timing of the
scheduled period 3. Can be
turned on or off by selecting
the check box.
Cleared (OFF)
Period.4
Shows the timing of the
scheduled period 4. Can be
turned on or off by selecting
the check box.
Cleared (OFF)
Period.5
Shows the timing of the
scheduled period 5. Can be
turned on or off by selecting
the check box.
Cleared (OFF)
Shows times and days of the
week of the usual schedule or
period schedule selected in
[Schedule view].
Green vertical line: projector
on; gray vertical line: projector
off; blue vertical line: switch
input signals.
Up to 8 schedules can be set
per day.
—
Time Schedule
Clicking an item in [Time Schedule] displays the [Edit schedule] screen, enabling
you to edit the schedule of the selected day or time.
Advanced Guide
Period.1
Using the Projector on a Network
167
Using the Projector on a Network
Item
Edit
schedule
Explanation
Factory default setting
Day
Shows the day of the week for
the selected schedule.
—
Time
Enter the automatic execution
time in 1-byte numbers, in the
range 00:00 to 23:59.
<Blank>
Operation
As the operation for automatic
execution, choose [Power],
[Input], or [Calibration].
Power
Parameter
As parameters for automatic
execution, choose from the
following options.
• When [Operation] is set to
[Power]:
ON / OFF
• When [Operation] is set to
[Input]:
DVI-1 / DVI-2 / DVI-3 /
DVI-4 / HDMI-1 / HDMI-2 /
DVI 1x4 / DVI 2x2 /
DVI 1x2 / HDMI 1x2
• When [Operation] is set to
[Calibration]:
LIGHT
ON
Clicking [Add schedule] in [Time Schedule] displays the [Add schedule] screen,
enabling you to add a new schedule to the selected usual schedule or period
schedule.
168
Using the Projector on a Network
Item
Add
schedule
Explanation
Factory default setting
Day
Select a day of the week for
automatic execution. Multiple
days can be selected.
Cleared
Time
Enter the automatic execution
time in 1-byte numbers, in the
range 00:00 to 23:59.
<Blank>
Operation
As the operation for automatic
execution, choose [Power],
[Input], or [Calibration].
Power
Parameter
As parameters for automatic
execution, choose from the
following options.
• When [Operation] is set to
[Power]:
ON / OFF
• When [Operation] is set to
[Input]:
DVI-1 / DVI-2 / DVI-3 /
DVI-4 / HDMI-1 / HDMI-2 /
DVI 1x4 / DVI 2x2 /
DVI 1x2 / HDMI 1x2
• When [Operation] is set to
[Calibration]:
LIGHT
ON
Schedule
copy
Explanation
Factory default setting
Copy origin
Select the day to copy from.
Mon
Registration
Events
Shows schedule details on
the selected day.
<Blank>
Copy to day
Select the day to copy to.
Cleared
Multiple days can be selected.
169
Using the Projector on a Network
Item
Advanced Guide
Clicking [Copy schedule to different day] in [Time Schedule] displays the [Schedule
copy] screen, enabling you to copy a schedule to any day for the selected usual
schedule or period schedule.
Using the Projector on a Network
Basic Wired Network Settings [Wired]
From [Wired] on the settings screen, you can complete basic network information
for wired connections. For the setting procedure, refer to “Network Setting” (P161).
Item
Explanation
Factory default setting
MAC address
Shows the projector’s wired
MAC address.
The projector’s wired MAC
address
IPv4
address
DHCP
Select whether to turn the
DHCP function on or off for
wired LAN (IPv4). The
following settings cannot be
configured manually when
this setting is [ON], because
the IP address is acquired
from the DHCP server.
[IP address]
[Subnet mask]
[Default gateway]
OFF
IP address
Enter the projector’s wired
LAN (IPv4) IP address in 1byte numbers.
192.168.254.254
Subnet mask
Enter the wired LAN (IPv4)
subnet mask in 1-byte
numbers.
255.255.255.0
Default gateway
Enter the wired LAN (IPv4)
default gateway address in 1byte numbers.
0.0.0.0
170
Using the Projector on a Network
Item
IPv6
address
IPv6
Explanation
Specify on or off for the IPv6
function of the wired LAN
(IPv6).
Choosing OFF will prevent
you from configuring the
following settings.
[Autoconfiguration]
[IP address]
[Prefix length]
[Default gateway]
Factory default setting
OFF
OFF
IP address
Enter the wired LAN (IPv6)
address in 1-byte numbers.
<Blank>
Prefix length
Enter the wired LAN (IPv6)
prefix length in 1-byte
numbers.
<Blank>
Default gateway
Enter the wired LAN (IPv6)
default gateway address in 1byte numbers.
<Blank>
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to
the network.
If the network subnet mask was changed, select [Subnet mask] in the above screen and
set the new subnet mask.
Advanced Guide
Autoconfiguration Select on or off for the auto
setting function of the wired
LAN (IPv6).
Choosing ON will prevent you
from configuring the following
settings.
[IP address]
[Prefix length]
[Default gateway]
Using the Projector on a Network
171
Using the Projector on a Network
Basic Wireless Network Settings [Wireless]
From [Wireless] on the settings screen, you can complete basic network
information for wireless connections. For the setting procedure, refer to “Network
Setting” (P161).
Item
Explanation
Factory default setting
MAC address
Shows the projector’s
wireless MAC address.
The projector’s wireless MAC
address
IPv4
address
DHCP
Select whether to turn the
DHCP function on or off for
wireless LAN (IPv4). The
following settings cannot be
configured manually when
this setting is [ON], because
the IP address is acquired
from the DHCP server.
[IP address]
[Subnet mask]
[Default gateway]
OFF
IP address
Enter the projector’s wireless
LAN (IPv4) IP address in 1byte numbers.
192.168.253.254
Subnet mask
Enter the wireless LAN (IPv4)
subnet mask in 1-byte
numbers.
255.255.255.0
Default gateway
Enter the wireless LAN (IPv4)
default gateway address in 1byte numbers.
0.0.0.0
172
Using the Projector on a Network
IPv6
address
Explanation
Specify on or off for the
wireless LAN (IPv6) function.
Choosing OFF will prevent
you from configuring the
following settings.
[Autoconfiguration]
[IP address]
[Prefix length]
[Default gateway]
OFF
Factory default setting
Autoconfiguration Select on or off for the auto
setting function of the wireless
LAN (IPv6).
Choosing ON will prevent you
from configuring the following
settings.
[IP address]
[Prefix length]
[Default gateway]
OFF
Enter the wireless LAN (IPv6) <Blank>
IP address in 1-byte numbers.
Prefix length
Enter the wireless LAN (IPv6)
prefix length in 1-byte
numbers.
<Blank>
Default gateway
Enter the wireless LAN (IPv6)
default gateway address in 1byte numbers.
<Blank>
Wi-Fi Protected
Setup
Select a simple method of
establishing a wireless
connection.
None (Manual)
Mode
Select the wireless
connection mode.
infrastructure mode
Select SSID
Select the wireless access
point’s SSID. Click the
[Refresh] button to update the
list. If the SSID is not listed,
enter it in 1-byte
alphanumeric characters (132 characters).
<Blank>
Security
Select the wireless security
setting.
Open
Channel
Shows the wireless channel
number. When [Mode] is set
to projector access point (PJ
AP) mode, a channel can be
selected.
1
Key ID
Select the wireless WEP key
ID.
1
Key type
Select the wireless security
key input type.
ASCII
173
Using the Projector on a Network
IP address
Advanced Guide
Wireless
setting
Item
IPv6
Using the Projector on a Network
Item
Wireless
setting
Explanation
Key
Enter the wireless security
key.
Factory default setting
<Blank>
If settings related to TCP/IP were changed, it is necessary to disconnect and reconnect to
the network. If the network subnet mask was changed, select [Subnet mask] in the above
screen and set the new subnet mask.
Setting Up Email [Mail]
From [Mail] in the settings screen, you can set the items necessary to send error
mails and test mails. For the setting procedure, refer to “Network Setting” (P161).
Item
Explanation
Factory default setting
Error report
Select whether to turn the error mail
sending function on or off, and IPv4 or
IPv6 for the network to use.
OFF
To:
Enter the recipient address for error
mails in 1-byte alphanumeric characters
and symbols (1 - 63 characters).
MailUserAccount
Cc:
Enter the CC address for error mails in
1-byte alphanumeric characters and
symbols (1 - 63 characters).
<Blank>
From:
Enter the sender address for error mails
in 1-byte alphanumeric characters and
symbols (1 - 63 characters).
[email protected]
IPv4 SMTP server IP
address
Enter the SMTP server IP address
(IPv4) in 1-byte numbers.
0.0.0.0
IPv4 SMTP server port
number
Enter the SMTP server port number
(IPv4) in 1-byte numbers (1 - 65535).
25
174
Using the Projector on a Network
Item
Explanation
Factory default setting
IPv6 SMTP server IP
address
Enter the SMTP server IP address
(IPv6) in 1-byte numbers.
<Blank>
IPv6 SMTP server port
number
Enter the SMTP server port number
(IPv6) in 1-byte numbers (1 - 65535).
25
Mail resend interval*
Enter the interval for resending mail
when an error occurred (unit: seconds)
within the range of 0 - 59 seconds using
1-byte numbers.
10
Mail resend times
Enter the number of times to resend
mail when an error occurred within the
range of 0 - 255 using 1-byte numbers.
3
* When the interval is set to 0 seconds, repeated attempts to send mail are made
(as set in [Mail resend times]) without pausing between attempts.
Mail Authentication Settings
From [Mail auth] under [Mail] in the settings screen, you can configure the settings
for authentication of mail that is sent when an error occurs. For the setting
procedure, refer to “Network Setting” (P161).
Item
Explanation
Factory default setting
OFF
User name
Enter the user name to use for mail
authentication in 1-byte alphanumeric
characters and symbols (1 - 63
characters).
<Blank>
Password
Enter the password for mail
authentication in 1-byte alphanumeric
characters and symbols (1 - 63
characters).
<Blank>
Confirm password
For confirmation, enter the same
password as you entered in
[Password].
<Blank>
IPv4 POP3 server IP
address
Enter the POP3 server IP address
(IPv4) in 1-byte numbers.
0.0.0.0
IPv4 POP3 server port
number
Enter the POP3 server port number
(IPv4) in 1-byte numbers (1 - 65535).
110
IPv6 POP3 server IP
address
Enter the POP3 server IP address
(IPv6) in 1-byte numbers.
<Blank>
IPv6 POP3 server port
number
Enter the POP3 server port number
(IPv6) in 1-byte numbers (1 - 65535).
110
POP before SMTP
response time
Enter the SMTP authentication timeout
period after POP3 authentication (unit:
milliseconds) using 1-byte numbers
(0 - 9999 milliseconds).
300
175
Using the Projector on a Network
Select the mail authentication method.
If OFF is selected, the other mail
authentication settings cannot be
changed.
Advanced Guide
Mail authentication
Using the Projector on a Network
Sending a Test Mail
You can send a test mail to the mail address specified in [Mail] under [Mail] in the
settings screen by clicking [Send test mail] at the bottom of the screen.
SNMP Settings [SNMP]
From [SNMP] in the settings screen, you can configure the settings related to
control of projectors which use SNMP (Simple Network Management Protocol). For
the setting procedure, refer to “Network Setting” (P161).
Item
Explanation
Factory default setting
SNMP
Select the SNMP function version. If
OFF is selected, the SNMP function will
be turned off and the other settings in
this screen cannot be configured.
OFF
Receive community
Enter the community name which will
receive projector information in 1-byte
alphanumeric characters and symbols
(1 - 15 characters).
<Blank>
Password
Enter the community settings password
in 1-byte alphanumeric characters and
symbols (8 - 15 characters). It can be
set only when the SNMP version is V3.
<Blank>
Confirm password
For confirmation, enter the same
<Blank>
password as you entered in [Password].
176
Using the Projector on a Network
Setting Projector Information [Projector info.]
From [Projector info.] in the settings screen, you can enter relevant comments such
as projector names and locations where projectors are installed so that the
information can be used to identify projectors when multiple projectors are installed
on the network. For the setting procedure, refer to “Network Setting” (P161).
Item
Explanation
Factory default setting
Projector name
Enter the projector name in 1-byte
alphanumeric characters and symbols
(1 - 63 characters).
Canon Projector001
Comment
Enter any relevant notes, such as
where the projector is installed.
<Blank>
Setting PJLink [PJLink]
177
Using the Projector on a Network
From [PJLink] in the settings screen, you can set the PJLink functions which are the
standard for projector management on a network. For the setting procedure, refer
to “Network Setting” (P161). For information about PJLink, refer to “What is
PJLink?” (P152).
Advanced Guide
Some characters such as # cannot be used for [Projector name] and [Comment].
Using the Projector on a Network
Item
Explanation
Factory default setting
PJLink
Turn the PJLink function on or off. If
OFF is selected, the PJLink function
will be turned off and the other settings
in this screen cannot be configured.
ON
PJLink authentication
Select whether to turn the PJLink
authentication function on or off. If OFF
is selected, it is not possible to change
the following items.
[Password]
[Confirm password]
ON
Password
Enter the PJLink authentication
password in 1-byte alphanumeric
characters (1 - 32 characters).
system
Confirm password
For confirmation, enter the same
password that you entered in
[Password].
system
Setting Up a Controller Manufactured by Crestron Electronics
[Crestron Controller]
The [Crestron e-Control] screen will open. For details on the Crestron Controller,
visit the Crestron website.
http://www.crestron.com/
Setting Errors
When a setting-related error occurs, the error name is displayed on the screen, and
a “ ” mark is displayed next to the input field which caused the error.
The error meanings are as shown below.
Error
Meaning
Input error
A setting outside the valid range was set on the
settings screen.
Password setting error
The set password and confirmation password did
not match.
Invalid SMTP
The SMTP server IP address has not been set.
178
Using the Projector on a Network
Error
Meaning
System failed to connect SMTP server.
Failed to connect to the SMTP server when
sending a test mail.
System failed to connect POP3 server.
Failed to connect to the POP3 server attempting
to send a test mail.
System doesn’t support this auth type.
An authentication type was set which is not
supported by the server.
System failed to authenticate.
Authentication failed attempting to send a test
mail.
The system failed to send the test mail.
Sending of test mail failed due to a connection
failure with the SMTP server or an error which
does not ordinarily occur.
Resetting Network Settings to the Default Settings
Perform steps 1 - 3 on “Displaying the Network Configuration Screen”
(P160) to display the settings screen.
2
Click [Initialize network settings].
3
A confirmation window appears. Click [OK].
Advanced Guide
1
Using the Projector on a Network
179
Using the Projector on a Network
■ Error Notification Mails
The messages shown in the following error list are sent when an error occurs in the
projector.
Error list
Errors related to
temperature
Error name
Errors related to
the light source
Error name
Errors related to
the air filter
Error name
Errors related to
the fan
Error name
Errors related to
the power
Error name
Text
Text
Text
Text
Text
Temperature abnormality
The internal temperature of the projector is abnormally
high, or else the ambient air temperature exceeds the
threshold. If the problem is with the projector, verify that it
is properly installed and is being used correctly, and let
the inside of the projector cool down for a while with the
power plug disconnected from the wall outlet before
resuming projection. Remove any objects that are
blocking the air intake or exhaust vent.
If the air filter is clogged, try cleaning or replacing it.
If the same warning is displayed again, the main unit may
be faulty. Please contact your dealer.
Light source abnormality
The light source unit or a related component may be
faulty. With the power off, disconnect the power plug from
the wall outlet, wait for a while, and then plug it in again
and turn the power back on. If the same warning is
displayed again, please contact your dealer.
Faulty air filter unit
The air filter is incorrectly installed, or a related
component may be faulty. With the power off, re-install
the air filter correctly, then turn the power back on. If the
same warning is displayed again, please contact your
dealer.
Faulty cooling fan
The cooling fan or a related component may be faulty.
With the power off, disconnect the power plug from the
wall outlet, and then plug it in again and turn the power
back on. If the same warning is displayed again, please
contact your dealer.
Faulty power supply
The power supply voltage may be abnormal, or a related
component may be faulty. With the power off, disconnect
the power plug from the wall outlet, and then plug it in
again and turn the power back on. If the same warning is
displayed again, please contact your dealer.
180
Using the Projector on a Network
Controlling the Projector from a Computer
The projector can be controlled from a computer over a wired or wireless network
connection.
1
2
Turn on the computer and projector.
Launch a web browser, enter “http://(projector IP address)” in the
address bar, and press the Enter key.
The projector web screen appears.
The factory default IP address is “192.168.254.254” for wired connections and
“192.168.253.254” for wireless connections. If DHCP settings are used, ask the network
administrator for the projector IP address. It is possible to check the IP address from the
projector menu.
Click [Projector control] on the web screen.
The password input window appears.
4
Enter the user name and password on the password input window, then
click [OK].
The factory default user name is “root” and the password is “system”.
Using the default user name and password unchanged opens up the risk of
unauthorized operation of the projector by a malicious third party.
To enhance security, it is highly recommended that you change the user name
and password. (P163)
The projector control screen appears.
Item
Explanation
Projector name
The name of the connected projector is displayed. (P177)
Comment
Shows notes, such as where the projector is installed. (P177)
Refresh
Refreshes the displayed contents with the most recent information.
Power
Turns projector power on or off.
Input
Select an input signal and click [Apply] to change to that input signal.
(P55)
Aspect
Select an aspect and click [Apply] to change to that aspect. (P64)
Image mode
Select an image mode and click [Apply] to change to that image mode.
(P68)
Blank
Switches the blank setting on or off. (P72)
181
Using the Projector on a Network
The projector can be controlled from this screen.
Advanced Guide
3
Using the Projector on a Network
Item
5
Explanation
Mute
Switches the mute setting on or off. (P34)
Information
Shows the results of control, or control error information, at the top of
the screen.
When the operations are finished, click [Back to top] to return the initial
web screen.
182
Advanced Projection
Projecting from Multiple Projectors at Once
(Edge Blending)
The brightness of overlapping image edges from multiple projectors used together
can be adjusted to make them blend in better.
■ Basic Instructions
Follow these steps when using two projectors side by side.
1
In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust].
• If you have already completed edge blending settings, selecting [Adjust] will apply
them.
• To redo adjustment from the beginning, select [Reset].
2
Set [Marker] to [On].
Marker lines are projected on the images. The red marker indicates the start
position for adjustment, and the green marker, the end position.
Adjust [Start position] for the side where images overlap. Move the start
marker to the outer edge of the overlapping area, or press a number
button on the remote control to specify the start position.
4
Adjust [Width]. Move the end marker to the inner edge of the overlapping
area, or press a number button on the remote control to specify the width
of the area to correct.
The area between the starting and ending markers is called the blending area.
Values indicated for this blending area are adjusted to match manually entered
blending area values. Shading is applied to this area, and the brightness is
adjusted to match portions that overlap with other areas. After you complete
settings for one image, do the same thing for the other one to specify the
blending area. Adjust the settings to make the blending area for each image
the same.
5
Set [Marker] to [Off].
183
Advanced Projection
3
Advanced Guide
By default, the green and red markers are displayed in the same position, so only the red
marker is visible.
Advanced Projection
■ Color Adjustment
In overlapping projection, portions of images in the overlapping area that pick up
other colors or are miscolored may be more noticeable. You can make this
overlapping area appear less distracting by performing Color blending adjustment.
1
In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Color blending adjustment] > [Adjust].
2
As you watch the image, adjust the value to eliminate unwanted colors in
the overlapping area.
First adjust red, green, and blue together by changing the [White] value, and
then adjust [Red], [Green], and [Blue] values individually.
3
Repeat this adjustment on all projectors.
■ Black Level Adjustment
In overlapping projection, dark colors are projected with less intensity than other
colors in the overlapping area. You can make this overlapping area less distracting
by adjusting the black level of non-overlapping image areas.
Left image
Right image
Area where dark colors look lighter
Position of end marker (hidden)
D-area
Blending area
Here, the non-overlapping image area (from the end marker toward the center of
the image) is called area “D.”
Normally, three areas are identified in the context of end markers: A, B, and C.
In the following instructions, only area D is adjusted, and the widths of A, B, and C
are left at the default value of 0.
To prepare for adjustment, set [No signal screen] to [Black], start projection with no input
signal, and turn off the room lights, so that you can check dark image areas. (P118)
184
Advanced Projection
1
In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Black level adjustment] > [Adjust].
2
3
Select [Adjustment type] > [Black level].
After selecting [D-area base], as you watch the image, adjust the values
so that the brightness and colors of the blending area and area D match.
Adjust [D-area base] to lighten the black level, and adjust [Red], [Green], and
[Blue] to obtain an optimal black level color tone, as needed.
4
Repeat this adjustment on all projectors.
■ Smoother Overlapping Areas
The black level along the right edge of area D (along the blending area) may be
more noticeable than that of surrounding areas.
By adjusting the black level of area B, you can make the transition smoother.
To compensate, adjust each area as follows.
Position of end marker (hidden)
Left image
CBA
D-area
Blending area
Areas C–A (default width: 0)
1
In the [Install settings] menu, select [Professional settings] > [Edge
blending] > [Adjust] > [Black level adjustment] > [Adjust].
2
Select [Adjustment type] > [Area] > [Side] > [Right].
185
Advanced Projection
When the projected image has multiple blending areas (on the top, bottom, and
each side), the width of areas A, B, and C must be adjusted to suit these blending
areas.
In this example, instructions are given for adjusting area B.
Advanced Guide
Area A: Black level cannot be adjusted.
Area B: Adjust to a black level different from that of area
D.
Area C: Adjust to provide a smooth transition relative to
the black levels of areas B and D.
Advanced Projection
3
Select [B-width], and then specify the width of area B.
Adjust the width of area B so that it roughly matches the area where the black
level of area B stands out. This will make the width of area D narrower.
4
Select [Adjustment type] > [Black level]. Adjust [B-area base] as you
watch the image.
• Results of adjusting the black level of area B are applied to all sides.
• Blending can be fine-tuned by adjusting [Adjustment type] > [Black level] > [Red],
[Green], and [Blue].
5
6
As you watch the image, adjust the width of areas A, B, and C.
Readjust the black level of area B, as needed.
To reduce distracting colors and colors that are out of alignment in areas where the images
overlap, perform [Color blending adjustment] targeting the main tone in the envisaged projected
image.
If you perform adjustments using [Color blending adjustment] or other menus, that may
not eliminate the distracting colors and differences in brightness in areas where the
images overlap.
186
Advanced Projection
Advanced Registration to Adjust Projected
Images
This feature enables precise correction of red, green, or blue misalignment in
different areas of the screen by color and area.
Two methods of registration are available: 5-point adjustment (using points in the
corners and center of the screen) and more precise manual adjustment based on
54 points (in a 6 x 9 grid).
Any values you set in 5-point adjustment are retained if you subsequently perform
manual adjustment. For more precise correction after 5-point adjustment, perform
manual adjustment.
• Adjust zoom and lens shift as needed before using [Advanced registration].
• Performing keystone adjustment will prevent accurate adjustment with [Advanced
registration]. If keystone adjustment is required, complete adjustment with [Advanced
registration] first.
■ Registration Using 5-Point Adjustment
5-point adjustment enables basic correction of color misalignment across the
screen, by moving adjustment points in each corner and the center.
1
In the [Install settings] menu, select [Professional settings] > [RGB
alignment] > [Advanced registration] > [Adjust] > [5-point adjustment] >
[Adjust].
The projector enters 5-point adjustment mode, and a chart is displayed.
Advanced Projection
187
Advanced Guide
• Charts (point selection windows) of two different sizes are used, depending on the
[Panel drive mode] setting.
• With advanced registration, checkered or halftone image areas may be affected by
uneven colors or image artifacts.
Advanced Projection
2
Use the [ ] / [ ] / [ ] / [ ] buttons to select the point for correction, and
then press the OK button.
The projector enters color selection mode.
Press the MENU button to return to [Advanced registration].
3
Select [Red] or [Blue] as the color, and then press the OK button.
• Each time you select [Chart] and press the OK button, display switches between the
chart and the source signal.
• Accessing the 5-point adjustment window during test pattern projection will show the
test pattern instead of your supplied signal.
4
Use the [ ] / [ ] / [ ] / [ ] buttons to align the adjustment points.
5
6
Press the OK button to return to the window for color selection mode.
Repeat this process to align the remaining colors and adjustment points.
188
Advanced Projection
■ Manual Registration
Use manual adjustment to correct registration only in certain areas.
Any manual adjustment values set before switching to 5-point adjustment are cleared.
1
In the [Install settings] menu, select [Professional settings] > [RGB
alignment] > [Advanced registration] > [Adjust] > [Manual adjustment].
The projector enters manual adjustment mode, and a chart is displayed.
• Charts (point selection windows) of two different sizes are used, depending on the
[Panel drive mode] setting.
• With advanced registration, checkered or halftone image areas may be affected by
uneven colors or image artifacts.
2
Use the [ ] / [ ] / [ ] / [ ] buttons to select the point for correction, and
then press the OK button.
The projector enters color selection mode.
Advanced Guide
189
Advanced Projection
Press the MENU button to return to [Advanced registration].
Advanced Projection
3
Select [Red], [Green], or [Blue] as the color, and then press the OK
button.
• Each time you select [Chart] and press the OK button, display switches between the
chart and the source signal.
• Accessing the manual adjustment window during test pattern projection will show the
test pattern instead of your supplied signal.
4
Use the [ ] / [ ] / [ ] / [ ] buttons to align the adjustment points.
5
6
Press the OK button to return to the window for color selection mode.
Repeat this process to align the remaining colors and adjustment points.
■ Resetting Image Registration
Clears the values set in 5-point adjustment or manual adjustment.
1
In the [Install settings] menu, select [Professional settings] > [RGB
alignment] > [Advanced registration] > [Adjust] > [Reset].
A confirmation message for resetting is displayed.
2
Select [OK] to reset the adjustment.
The following tasks are executed.
• Values set in 5-point adjustment are cleared.
• 5-point adjustment is deactivated.
• Values set in manual adjustment are cleared.
190
Advanced Projection
Adjusting Peripheral Focus
This feature enables focus adjustment around the edges of the screen.
• Use marginal focus adjustment for curved screens, such as domes.
• Use marginal focus adjustment to bring images on flat screens into focus if image
edges remain warped after you adjust the overall focus.
[Marginal focus] must be set to [On] in advance. (P112)
■ Bringing Image Edges into Focus
To adjust peripheral focus, press the FOCUS button on the remote control or the
LENS button on the projector.
1
Press the FOCUS button on the remote control twice to display the
marginal focus adjustment window.
Remote control
Press twice.
Pressing the LENS button on the projector repeatedly switches between
windows for lens-related parameters.
Press the LENS button twice to display the marginal focus adjustment window.
Advanced Guide
Projector
Press twice.
When [Marginal
focus] is set to [Off].
191
Advanced Projection
When [Marginal focus]
is set to [On].
Advanced Projection
2
Press the pointer buttons to adjust the focus at image edges.
Remote control
Projector
Press the [ ] / [ ] / [ ] / [ ] buttons to adjust peripheral focus.
3
Once image edges are in focus, press the OK or FOCUS button.
■ Resetting Adjustment
Clears the values set in marginal focus adjustment.
In the [Install settings] menu, select [Professional settings] > [Marginal focus] >
[Reset] to reset the adjustment.
The following tasks are executed.
• Values set in marginal focus adjustment are cleared.
• [Marginal focus] is set to [Off].
Setting [Marginal focus] to [Off] will not reset the setting value for peripheral focus.
■ Using Trigger out
If you connect a screen or other external device to the projector’s trigger terminal
(P32) and configure [System settings], [Trigger out], [Link with power] (P133),
operation of the device can be triggered by turning the projector on or off.
192
Safety Instructions
Before Use
Other Information
Installation Procedure
Basic Guide
Connection Procedure
Projection Procedure
Convenient Features
Using Menus
Advanced Guide
Menu Configuration
Menu Settings
Using the Projector on a
Network
Advanced Projection
Other Information
193
Maintenance
Product Specifications
Troubleshooting
Maintenance
Cleaning the Projector
Clean the projector frequently to prevent dust from settling on the surface.
A dirty lens may ruin the quality of the projected image.
Before cleaning the projector, always turn it off, unplug it after the
cooling fan stops, and wait at least one hour. Otherwise, you may get
burned because the main unit is very hot immediately after the
projector is turned off.
Wipe the projector’s main unit softly with a soft cloth.
If the projector is heavily soiled, soak the cloth in water with a small amount of
detergent in it, squeeze the cloth thoroughly, and then wipe the projector with it.
After cleaning, wipe the projector with a dry cloth.
• Never use volatile cleaning liquid or benzine, as
these may damage the finish of the projector.
• When using a chemical dust cloth, make sure to
read the instructions thoroughly.
• When cleaning the projector’s lens, use a
commonly available air blower or lens cleaning
paper. The lens surface is easily damaged, so do
not use a hard cloth or tissues.
Replacing the Air Filter
The air filter protects the lens and mirror inside the projector from dust and dirt.
Should the air filter become clogged with dust, the projector may be damaged since
it will block the air flow into the projector and raise the internal temperature of the
projector. (P208)
The following screen is displayed when turning on the projector if the air filter needs
to be replaced. Replace the air filter if it is displayed.
• Only the [ ], [ ], OK, POWER, EXIT, FOCUS, ZOOM
and SHIFT buttons are available while this screen is
displayed. (When you press the POWER button, the
“Push POWER button again to turn off power.”
message appears.)
• When this screen has disappeared after being
displayed for 10 seconds, all buttons become operable.
Follow the procedure below when replacing the air filter.
1
Turn off the projector power and remove the power plug.
194
Maintenance
2
Pull out the filter cover by
gripping the two tabs at the
bottom and lifting.
3
Open the filter cover and remove
it.
4
Grasp the air filter by the
handles and remove it.
Other Information
Maintenance
195
Maintenance
5
Holding the new air filter by the
tab, insert the air filter in the
projector.
6
Align the filter cover tab with the
groove and close the filter cover.
• Handle the air filter carefully. If damaged, the air filter will not work properly.
• To purchase a replacement air filter (part no: RS-FL04), contact the Canon Customer
Support Center or visit the Canon website.
196
Product Specifications
Displayed Test Patterns
To access the test pattern menu, from the [Install settings] menu, select [Test
pattern] (P116) > [On], or press the TEST PATTERN button on the remote control.
While the test pattern is displayed, you can use the [ ] / [ ] buttons to switch
patterns. Also, if there is an option pattern available, you can use the [ ] / [ ]
buttons to switch pattern.
The following test patterns can be displayed.
Use [ ] / [ ] to
switch patterns
(1)
Use [ ] / [ ] to switch
option patterns
Color bars
(2)
Stairstep H
(3)
Stairstep V
(4)
Raster 100%
(White / red / green / blue)
(5)
Raster 50%
(White / red / green / blue)
(6)
Color steps
(7)
Checker
(8)
Multi
Character
(10)
Focus
(11)
Border
(13)
Cross Hatch
DICOM
197
Product Specifications
(12)
Other Information
(9)
Product Specifications
Supported Signal Types
The projector automatically projects input signals correctly from computers or AV
equipment compatible with any of these signals.
HDMI (single)
FP : Front porch
SW : Sync width
BP : Back porch
1
Signal
resolution
640x480
720x480
720x576
800x600
1280x720
1024x768
1366x768
1440x900
1280x1024
1920x1080(I)
1920x1080
2048x1080
2560x1080
1920x1200
2048x1200
2560x1440
2560x1600
3840x2160
4096x2160
Horizontal Vertical
frequency frequency
[Hz]
[kHz]
31.469
31.469
31.250
37.879
18.000
37.500
45.000
48.363
47.712
48.000
55.469
55.935
63.981
28.125
31.250
33.750
27.000
56.250
67.500
66.576
67.500
26.400
56.250
66.636
66.000
74.038
74.556
74.582
74.100
88.787
98.713
52.593
52.438
54.000
56.250
67.500
112.500
135.000
52.561
52.397
54.000
56.250
67.500
112.500
135.000
59.940
59.940
50.000
60.317
24.000
50.000
60.000
60.004
59.790
60.000
59.901
59.887
60.020
50.000
50.000
60.000
24.000
50.000
60.000
59.924
60.000
24.000
50.000
59.978
60.000
59.950
59.885
59.905
60.000
59.951
59.972
23.993
23.999
24.000
25.000
30.000
50.000
60.000
23.979
23.980
24.000
25.000
30.000
50.000
60.000
Dot clock
[MHz]
HDMI multi input
mode
25.175
27.000
27.000
40.000
59.400
74.250
74.250
65.000
85.500
72.000
88.750
106.500
108.000
74.250
72.000
74.250
74.250
148.500
148.500
147.000
148.500
99.000
185.625
181.250
198.000
154.000
193.250
205.250
157.684
241.500
268.500
266.750
209.750
297.000
297.000
297.000
594.000
594.000
284.250
223.000
297.000
297.000
297.000
594.000
594.000
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal*3, Single*3
Normal*3, Single*3
Normal, Single
Normal, Single
Normal, Single
Normal*3, Single*3
Normal*3, Single*3
198
Blanking information
Horizontal
Vertical
FP, SW, BP
FP, SW, BP
16, 96, 48
16, 62, 60
12, 64, 68
40, 128, 88
1760, 40, 220
440, 40, 220
110, 40, 220
24, 136, 160
70, 143, 213
14, 56, 64
48, 32, 80
80, 152, 232
48, 112, 248
528, 44, 148
32, 168, 184
88, 44, 148
638, 44, 148
528, 44, 148
88, 44, 148
48, 32, 80
44, 44, 64
998, 44, 148
548, 44, 148
48, 32, 80
248, 44, 148
48, 32, 80
136, 200, 336
136, 216, 352
8, 32, 40
48, 32, 80
48, 32, 80
216, 400, 616
48, 32, 80
1276, 88, 296
1056, 88, 296
176, 88, 296
1056, 88, 296
176, 88, 296
224, 432, 656
48, 32, 80
1020, 88, 296
968, 88, 128
88, 88, 128
968, 88, 128
88, 88, 128
10, 2, 33
9, 6, 30
5, 5, 39
1, 4, 23
5, 5, 20
5, 5, 20
5, 5, 20
3, 6, 29
3, 3, 24
1, 3, 28
3, 6, 17
3, 6, 25
1, 3, 38
4.5, 10, 30.5
45.5, 10, 114.5
4.5, 10, 30.5
4, 5, 36
4, 5, 36
4, 5, 36
3, 10, 18
4, 5, 36
4, 5, 11
4, 5, 36
3, 10, 18
4, 5, 11
3, 6, 26
3, 6, 36
3, 10, 32
21, 8, 6
3, 5, 33
3, 6, 37
3, 5, 24
3, 5, 17
8, 10, 72
8, 10, 72
8, 10, 72
8, 10, 72
8, 10, 72
3, 10, 19
3, 10, 12
8, 10, 72
8, 10, 72
8, 10, 72
8, 10, 72
8, 10, 72
Product Specifications
When you apply the settings in the HDMI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
HDMI 1x2
1
FP : Front porch
SW : Sync width
BP : Back porch
2
Combined Resolution at Horizontal Vertical
Dot clock
each input frequency frequency
multi input
[MHz]
[Hz]
[kHz]
terminal
resolution
1280x480
1440x480
1440x576
640x480
720x480
720x576
2560x720
1280x720
3840x1080
1920x1080(I)
3840x1080
2560x1600
1920x1080
1280x1600
3840x2160
1920x2160
4096x2160
2048x2160
3200x2400
3840x2400
1600x2400
1920x2400
31.469
31.469
31.250
37.500
45.000
28.125
33.750
67.500
98.611
52.404
54.000
112.500
133.293
135.000
133.320
52.515
52.423
54.000
112.500
133.265
133.320
135.000
148.011
148.140
59.940
59.940
50.000
50.000
60.000
50.000
60.000
60.000
59.910
23.983
24.000
50.000
59.988
60.000
60.000
23.957
23.992
24.000
50.000
59.975
60.000
60.000
59.948
60.000
25.175
27.000
27.000
74.250
74.250
74.250
74.250
148.500
142.000
109.000
148.500
297.000
277.250
297.000
266.640
142.000
115.750
148.500
297.000
294.250
283.704
297.000
260.500
296.280
HDMI multi
input mode
Normal, 1x2
Normal, 1x2
Normal, 1x2
Normal, 1x2
Normal, 1x2
Normal, 1x2
Normal, 1x2
Normal, 1x2
1x2
1x2*2
1x2
Normal, 1x2
1x2
1x2
Normal, 1x2
1x2*1
Blanking information
Horizontal
Vertical
FP, SW, BP FP, SW, BP
16, 96, 48
16, 62, 60
12, 64, 68
440, 40, 220
110, 40, 220
528, 44, 148
88, 44, 148
88, 44, 148
48, 32, 80
48, 32, 80
638, 44, 148
528, 44, 148
48, 32, 80
88, 44, 148
8, 32, 40
112, 216, 328
48, 32, 80
510, 44, 148
484, 44, 64
48, 32, 80
8, 32, 40
44, 44, 64
48, 32, 80
8, 32, 40
10, 2, 33
9, 6, 30
5, 5, 39
5, 5, 20
5, 5, 20
4.5, 10, 30.5
4.5, 10, 30.5
4, 5, 36
3, 10, 33
3, 10, 12
8, 10, 72
8, 10, 72
3, 10, 49
8, 10, 72
48, 8, 6
3, 10, 19
3, 10, 12
8, 10, 72
8, 10, 72
3, 10, 49
48, 8, 6
8, 10, 72
3, 10, 56
55, 8, 6
When you apply the settings in the HDMI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
DVI (single)
Signal
resolution
640x480
800x600
1280x720
1024x768
1440x900
1280x1024
1920x1080
2048x1080
31.469
37.879
45.000
48.363
47.712
48.000
55.469
55.935
63.981
27.000
67.500
66.576
67.500
59.940
60.317
60.000
60.004
59.790
60.000
59.901
59.887
60.020
24.000
60.000
59.924
60.000
Dot clock
[MHz]
DVI multi input
mode
25.175
40.000
74.250
65.000
85.500
72.000
88.750
106.500
108.000
74.250
148.500
147.000
148.500
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
Normal, Single
199
Blanking information
Horizontal
Vertical
FP, SW, BP
FP, SW, BP
16, 96, 48
40, 128, 88
110, 40, 220
24, 136, 160
70, 143, 213
14, 56, 64
48, 32, 80
80, 152, 232
48, 112, 248
638, 44, 148
88, 44, 148
48, 32, 80
44, 44, 64
10, 2, 33
1, 4, 23
5, 5, 20
3, 6, 29
3, 3, 24
1, 3, 28
3, 6, 17
3, 6, 25
1, 3, 38
4, 5, 36
4, 5, 36
3, 10, 18
4, 5, 36
Product Specifications
1366x768
Horizontal Vertical
frequency frequency
[Hz]
[kHz]
Other Information
FP : Front porch
SW : Sync width
BP : Back porch
1
Product Specifications
Signal
resolution
Horizontal Vertical
frequency frequency
[Hz]
[kHz]
66.636
66.000
74.038
74.556
74.049
88.787
52.438
52.397
2560x1080
1920x1200
2048x1200
2560x1440
3840x2160
4096x2160
59.978
60.000
59.950
59.885
59.959
59.951
23.999
23.980
Dot clock
[MHz]
DVI multi input
mode
181.250
198.000
154.000
193.250
163.500
241.500
209.750
223.000
Single
Normal, Single
Normal, Single
Normal, Single
Single
Single
Blanking information
Horizontal
Vertical
FP, SW, BP
FP, SW, BP
48, 32, 80
248, 44, 148
48, 32, 80
136, 200, 336
48, 32, 80
48, 32, 80
48, 32, 80
48, 32, 80
3, 10, 18
4, 5, 11
3, 6, 26
3, 6, 36
3, 10, 22
3, 5, 33
3, 5, 17
3, 10, 12
When you apply the settings in the DVI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
DVI 1x2
1
FP : Front porch
SW : Sync width
BP : Back porch
3
Combined Resolution at Horizontal Vertical
each input frequency frequency
multi input
[Hz]
[kHz]
terminal
resolution
2560x1080
2560x1440
2560x1600
1280x1080
1280x1440
1280x1600
3840x2160
1920x2160
4096x2160
2048x2160
66.493
88.715
98.611
52.512
52.404
54.000
67.500
52.515
52.423
54.000
67.500
59.850
59.902
59.910
23.956
23.983
24.000
30.000
23.957
23.992
24.000
30.000
Dot clock
[MHz]
DVI multi
input mode
95.750
127.750
142.000
132.750
109.000
148.500
148.500
142.000
115.750
148.500
148.500
1x2
1x2
Normal, 1x2
Normal*2, 1x2
1x2
Normal*2, 1x2
1x2
Blanking information
Horizontal
Vertical
FP, SW, BP FP, SW, BP
48, 32, 80
48, 32, 80
48, 32, 80
104, 200, 304
48, 32, 80
638, 44, 148
88, 44, 148
112, 216, 328
48, 32, 80
510, 44, 148
44, 44, 64
3, 10, 18
3, 10, 28
3, 10, 33
3, 10, 19
3, 10, 12
8, 10, 72
8, 10, 72
3, 10, 19
3, 10, 12
8, 10, 72
8, 10, 72
When you apply the settings in the DVI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
DVI 2x2
1
3
2
4
FP : Front porch
SW : Sync width
BP : Back porch
Combined Resolution at Horizontal Vertical
Dot clock
each input frequency frequency
multi input
[MHz]
[Hz]
[kHz]
terminal
resolution
3840x2160
1920x1080
4096x2160
2048x1080
4096x2304
2048x1152
27.000
33.750
66.587
67.158
67.500
27.000
33.750
66.576
67.160
67.500
70.992
71.584
72.000
24.000
30.000
59.934
59.963
60.000
24.000
30.000
59.924
59.964
60.000
59.909
59.903
60.000
74.250
74.250
138.500
173.000
148.500
74.250
74.250
147.000
183.750
148.500
156.750
197.000
162.000
200
DVI multi
input mode
Normal, 2x2
Normal, 2x2
Normal, 2x2
Normal, 2x2
Normal, 2x2
2x2*2
2x2*2
2x2
Normal, 2x2
Normal*1, 2x2*1
Normal*1, 2x2*1
Normal*1, 2x2*1
Blanking information
Horizontal
Vertical
FP, SW, BP FP, SW, BP
638, 44, 148
88, 44, 148
48, 32, 80
128, 200, 328
88, 44, 148
594, 44, 64
44, 44, 64
48, 32, 80
128, 216, 344
44, 44, 64
48, 32, 80
136, 216, 352
26, 80, 96
4, 5, 36
4, 5, 36
3, 5, 23
3, 5, 32
4, 5, 36
4, 5, 36
4, 5, 36
3, 10, 18
3, 10, 27
4, 5, 36
3, 5, 25
3, 5, 35
1, 3, 44
Product Specifications
Combined Resolution at Horizontal Vertical
Dot clock
each input frequency frequency
multi input
[MHz]
[Hz]
[kHz]
terminal
resolution
3200x2400
1600x1200
3840x2400
1920x1200
4096x2400
2048x1200
74.006
75.000
74.556
74.038
74.582
74.049
59.924
60.000
59.885
59.950
59.905
59.959
130.250
162.000
193.250
154.000
205.250
163.500
DVI multi
input mode
2x2*1
2x2*1
Normal, 2x2*1
Normal, 2x2*1
Normal, 2x2*1
Blanking information
Horizontal
Vertical
FP, SW, BP FP, SW, BP
48, 32, 80
64, 192, 304
136, 200, 336
48, 32, 80
136, 216, 352
48, 32, 80
3, 4, 28
1, 3, 46
3, 6, 36
3, 6, 26
3, 10, 32
3, 10, 22
When you apply the settings in the DVI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
DVI 1x4
FP : Front porch
SW : Sync width
BP : Back porch
1 2 3 4
Combined
multi input
resolution
3840x2160
4096x2160
4096x2304
3840x2400
4096x2400
Resolution at
each input
terminal
960x2160
1024x2160
1024x2304
960x2400
1024x2400
Horizontal Vertical
Dot clock
frequency frequency
[MHz]
[Hz]
[kHz]
134.036
133.259
133.319
135.000
134.055
133.235
133.320
135.000
142.103
143.111
142.199
147.991
149.096
148.139
148.970
148.015
148.139
59.918
59.973
60.000
60.000
59.926
59.962
60.000
60.000
59.959
59.979
60.000
59.940
59.974
60.000
59.924
59.949
60.000
178.000
149.250
138.652
148.500
188.750
157.750
147.185
148.500
168.250
201.500
156.988
165.750
198.000
154.065
209.750
175.250
163.546
DVI multi
input mode
1x4*2
Normal, 1x4
1x4*2
Normal, 1x4
1x4*1
1x4*1
1x4*1
Normal*1, 1x4*1
1x4*1
Normal*1, 1x4*1
Blanking information
Horizontal
Vertical
FP, SW, BP FP, SW, BP
80, 104, 184
48, 32, 80
8, 32, 40
44, 22, 74
80, 112, 192
48, 32, 80
8, 32, 40
22, 22, 32
48, 32, 80
80, 112, 192
8, 32, 40
48, 32, 80
80, 104, 184
8, 32, 40
80, 112, 192
48, 32, 80
8, 32, 40
3, 10, 64
3, 10, 49
48, 8, 6
8, 10, 72
3, 10, 64
3, 10, 49
48, 8, 6
8, 10, 72
3, 10, 53
3, 10, 69
52, 8, 6
3, 10, 56
3, 10, 73
55, 8, 6
3, 10, 73
3, 10, 56
55, 8, 6
When you apply the settings in the DVI multi input mode column, formats in corresponding rows are
identified in the EDID. No information is provided in the EDID for fields that are blank, so the computer
output format must be configured manually.
FP
SW
BP
Active
video
Video
signal
*1 Only when [Panel drive mode] is set to [4096x2400].
*2 Only when [Panel drive mode] is set to [4096x2160].
*3 Only YCbCr 4:2:0 is supported when [HDMI-1(2) EDID] is set to [9Gbps]. (RGB, YCbCr 4:4:4, and
YCbCr 4:2:2 are not supported.)
201
Product Specifications
Sync
signal
Other Information
Blanking interval
Active
video
Product Specifications
Specifications
■ Projector
Model name
4K600STZ
Reflective liquid crystal (LCOS): 3 panels
Optical system
Color separation by dichroic mirror / polarizing beam
splitter and color composition by prism
Effective display area
0.76'' / 128:75 (approx. 17:10)
Effective pixels
9,830,400 (4096 x 2400)
Other characteristics
Active matrix system
Zoom
1.3x (motorized)
Focus
Motorized
Lens shift
V: ±60% (motorized) H: ±10% (motorized)
Focal length
f = 17.2 – 22.3 mm
F number
F2.6
Type
Blue laser diode + yellow phosphor
Minimum: 101.6 cm (40"); maximum: 1,524 cm (600")
Projection distance: 0.9 – 17.7 m (3 – 58')
Number of colors
16,770,000 colors
Light output(*1)(*2)
(Light source mode: Normal /
Quiet 1 / Quiet 2)
6000 / 4560 / 2400lm
Contrast ratio(*1)(*3)(*7)
4000:1 (Fully white:fully black, native)
Ratio of brightness at periphery to
center(*1)
80%
Speaker
5W, monaural
Supported input signals
See “Supported Signal Types” (P198 – P201).
Computer signal input
Maximum input resolution: 4096 x 2400
Video signal input
Maximum input resolution: 4096 x 2160
Video signals
Image size and projection distance
Display
resolution
Light
source
Projection
lens
Display
device
Display system
DVI input
DVI
(single)
640 x 480, 800 x 600, 1280 x 720, 1024 x 768, 1366 x 768,
1440 x 900, 1280 x 1024, 1920 x 1080, 2048 x 1080, 2560
x 1080, 1920 x 1200, 2048 x 1200, 2560 x 1440, 3840 x
2160(*4), 4096 x 2160(*4)(*5)
DVI (1 x 2)
2560 x 1080, 2560 x 1440, 2560 x 1600, 3840 x 2160(*4),
4096 x 2160(*4)
DVI (2 x 2)
3840 x 2160, 4096 x 2160, 4096 x 2304(*6), 3200 x
2400(*6), 3840 x 2400(*6), 4096 x 2400(*6)
DVI (1 x 4)
3840 x 2160, 4096 x 2160, 4096 x 2304(*6), 3840 x
2400(*6), 4096 x 2400(*6)
202
Product Specifications
Video signals
Model name
HDMI
(single)
640 x 480, 720 x 480, 720 x 576, 800 x 600, 1280 x 720,
1024 x 768, 1366 x 768, 1440 x 900, 1280 x 1024, 1920 x
1080, 2048 x 1080, 2560 x 1080, 1920 x 1200, 2048 x
1200, 2560 x 1440, 2560 x 1600, 3840 x 2160, 4096 x
2160
HDMI
(1 x 2)
1280 x 480, 1440 x 480, 1440 x 576, 2560 x 720, 3840 x
1080, 2560 x 1600, 3840 x 2160, 4096 x 2160, 3200 x
2400(*6), 3840 x 2400(*5)(*6)
DVI-D x 4
Digital PC (29-pin DVI connector)
HDMI x 2
Digital PC, Digital video
HDMI input
Image signal input
terminals
Other input/output terminals
4K600STZ
Mini jack
Audio input
Mini jack
Audio output
Mini jack
Wired remote control
Mini jack
Trigger output (12 V)
RS-232C
CONTROL (Dsub9)
USB
USB Type A
RJ-45
Network connection (1000BASE-T/100BASE-TX/
10BASE-T)
37 / 32 / 29 dB (Light source mode: Normal / Quiet 1 /
Quiet 2)
Operating temperature
0°C (32°F) – 45°C (113°F)
Power supply
AC 100 V – 240 V 50 / 60Hz
Maximum power consumption
665 W
Standby power
consumption
Noise
LAN OFF
0.4 W
LAN ON
0.8 W
Mass
26.0 kg / 57.3 lbs
Accessories
Remote control, remote control dry-cell batteries, power
cord, lens cap, Important Information, User’s Manual (CDROM) and Warranty Card
Wireless
connectivity
559 mm (W) x 201 mm (H) x 624 mm (D) /
22.0 (W) x 7.9 (H) x 24.6 (D)
Standards
IEEE802.11b/g/n
Supported channels
1 CH - 11 CH
Frequency band
2.4 GHz
203
Product Specifications
(*1) Compliance with ISO21118-2012
(*2) In [Presentation] image mode, with motion blur reduction set to [Off] and the light source mode
set to [Normal].
(*3) In [4096x2400] panel drive mode, with motion blur reduction set to [Off] and the light source
mode set to [Normal].
(*4) Only low frequencies (24-30 Hz) supported
(*5) EDID not supported
Other Information
Standard dimensions
Product Specifications
(*6) When [Panel drive mode] is set to [4096x2400].
(*7) When [Close 3] is selected in [Iris].
* 99.99% or more of the LCD panel pixels are effective. During projection, 0.01% or less of pixels
may stay lit or unlit due to the characteristics of the LCD panel.
* Using the projector continuously for an extended period of time may accelerate the deterioration of
optical parts.
* Product specifications and appearance are subject to change without notice.
■ Remote Control
Model number
RS-RC05
Power supply
DC 3.0V, using two AA-size batteries
Operating range
Approx. 8 m / 26.2' ±25° horizontal and vertical (to infrared remote receiver)
51 mm (W) x 28 mm (H) x 176 mm (D) /
2.0 (W) x 1.1 (H) x 6.9 (D) in
Dimensions
Weight
100 g / 3.5 oz
■ External View
605 mm (23.8")
201 mm (7.9")
177 mm (7.0")
133 mm (5.2")
90 mm (3.5")
4K600STZ
559 mm (22.0")
624 mm (24.6")
204
Product Specifications
■ Service Port (CONTROL)
Pin assignment
Pin No.
1
2
3
4
5
6
7
8
9
Signal
OPEN
RxD
TxD
OPEN
GND
OPEN
Internal pull-up
OPEN
OPEN
Communication format
Communication mode
Communication speed
Character length
Stop bits
Parity
Flow control
: RS-232C, asynchronous, half-duplex communication
: 19200bps
: 8 bits
: 1/2 bits
: None
: None
Other Information
Product Specifications
205
Product Specifications
Main user commands
Commands
Power on
Power supply
ASCII representation
POWER=ON<CR>
50h 4Fh 57h 45h 52h 3Dh 4Fh 4Eh 0Dh
POWER=OFF<CR>
50h 4Fh 57h 45h 52h 3Dh 4Fh 46h 46h
0Dh
GET=POWER<CR>
47h 45h 54h 3Dh 50h 4Fh 57h 45h 52h
0Dh
HDMI-1
INPUT=HDMI1<CR>
49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh
49h 31h 0Dh
HDMI-2
INPUT=HDMI2<CR>
49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh
49h 32h 0Dh
HDMI 1x2
INPUT=HDMI1X2<CR>
49h 4Eh 50h 55h 54h 3Dh 48h 44h 4Dh
49h 31h 58h 32h 0Dh
DVI-1
INPUT=D-RGB1<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 31h 0Dh
DVI-2
INPUT=D-RGB2<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 32h 0Dh
DVI-3
INPUT=D-RGB3<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 33h 0Dh
DVI-4
INPUT=D-RGB4<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 34h 0Dh
DVI 1x2
INPUT=D-RGB1X2<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 31h 58h 32h 0Dh
DVI 2x2
INPUT=D-RGB2X2<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 32h 58h 32h 0Dh
DVI 1x4
INPUT=D-RGB1X4<CR>
49h 4Eh 50h 55h 54h 3Dh 44h 2Dh 52h
47h 42h 31h 58h 34h 0Dh
GET=INPUT<CR>
47h 45h 54h 3Dh 49h 4Eh 50h 55h 54h
0Dh
Standard
IMAGE=STANDARD<CR>
49h 4Dh 41h 47h 45h 3Dh 53h 54h 41h
4Eh 44h 41h 52h 44h 0Dh
Presentation
49h 4Dh 41h 47h 45h 3Dh 50h 52h 45h
IMAGE=PRESENTATION<CR> 53h 45h 4Eh 54h 41h 54h 49h 4Fh 4Eh
0Dh
Photo/sRGB
IMAGE=PHOTO_SRGB<CR>
49h 4Dh 41h 47h 45h 3Dh 50h 48h 4Fh
54h 4Fh 5Fh 53h 52h 47h 42h 0Dh
DICOM SIM
IMAGE=DCM_SIM<CR>
49h 4Dh 41h 47h 45h 3Dh 44h 43h 4Dh
5Fh 53h 49h 4Dh 0Dh
Dynamic
IMAGE=DYNAMIC<CR>
49h 4Dh 41h 47h 45h 3Dh 44h 59h 4Eh
41h 4Dh 49h 43h 0Dh
Video
IMAGE=VIDEO<CR>
49h 4Dh 41h 47h 45h 3Dh 56h 49h 44h
45h 4Fh 0Dh
User 1
IMAGE=USER_1<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 31h 0Dh
User 2
IMAGE=USER_2<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 32h 0Dh
User 3
IMAGE=USER_3<CR>
49h 4Dh 41h 47h 45h 3Dh 55h 53h 45h
52h 5Fh 33h 0Dh
GET=IMAGE<CR>
47h 45h 54h 3Dh 49h 4Dh 41h 47h 45h
0Dh
BRI=<value>CR
42h 52h 49h 3Dh <numeric code> 0Dh
Power off
Power status
acquisition
Input source
Input source
acquisition
Image Mode
Image mode
acquisition
Brightness
Binary representation
Brightness
value setting
206
Product Specifications
Commands
Brightness
acquisition
Sharpness
Sharpness
value setting
Sharpness
acquisition
Contrast
ASCII representation
GET=BRI<CR>
47h 45h 54h 3Dh 42h 52h 49h 0Dh
SHARP=<value><CR>
53h 48h 41h 52h 50h 3Dh <numeric
code> 0Dh
GET=SHARP<CR>
47h 45h 54h 3Dh 53h 48h 41h 52h 50h
0Dh
Contrast value
CONT=<value><CR>
setting
Contrast
acquisition
47h 45h 54h 3Dh 43h 4Fh 4Eh 54h 0Dh
Auto
ASPECT=AUTO<CR>
41h 53h 50h 45h 43h 54h 3Dh 41h 55h
54h 4Fh 0Dh
True size
ASPECT=TRUE<CR>
41h 53h 50h 45h 43h 54h 3Dh 54h 52h
55h 45h 0Dh
GET=ASPECT<CR>
47h 45h 54h 3Dh 41h 53h 50h 45h 43h
54h 0Dh
Blank On
BLANK=ON<CR>
42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 4Eh 0Dh
Blank Off
BLANK=OFF<CR>
42h 4Ch 41h 4Eh 4Bh 3Dh 4Fh 46h 46h
0Dh
GET=BLANK<CR>
47h 45h 54h 3Dh 42h 4Ch 41h 4Eh 4Bh
0Dh
Aspect value
acquisition
Blank
acquisition
43h 4Fh 4Eh 54h 3Dh <numeric code>
0Dh
GET=CONT<CR>
Aspect
Blank
Binary representation
Other Information
Product Specifications
207
Troubleshooting
LED Indicator Details
When there is a problem with the projector, the LED indicator on the side of the
projector illuminates or flashes continuously after the projector is turned off.
• Wait until the cooling fan stops and disconnect the power plug from the electrical outlet before
dealing with the problem.
LED indicator
Meaning
Cause and countermeasure
status
WARNING and Temperature The temperature inside the projector is too high for
TEMP are lit.
abnormality some reason or the outside air temperature is
higher than the operating range. If the problem is
inside the projector, check whether the projector is
installed and operating normally, unplug the
projector from the power outlet to cool down the
projector interior and then restart projection. If the
air intake or exhaust vent is blocked, remove the
obstacle. If the air filter is clogged, replace it.
(P194) If the same warning occurs again, there
may be a malfunction in the projector. Contact the
Canon Customer Support Center.
WARNING and Faulty light
The light source does not illuminate. Restart the
LIGHT are lit.
source
projector and check projection. If the light source
does not illuminate after this, the light source
drive circuit may be damaged. Contact the
Canon Customer Support Center.
WARNING
Filter error
The air filter is not installed correctly. Install the
(only) flashes
air filter correctly and restart the projector.
3 times
Contact the Canon Customer Support Center if
repeatedly.
the same warning occurs again.
WARNING
Faulty
There may be a malfunction in the cooling fan or
(only) flashes
cooling fan
another component. Unplug the projector from
4 times
the electrical outlet, then plug it back into the
repeatedly.
outlet and turn on the projector again. Contact
the Canon Customer Support Center if the same
warning occurs again.
WARNING
Faulty power Abnormal voltage is applied to some parts in the
(only) flashes
supply
power supply or another failure may have
5 times
occurred. Unplug the projector from the electrical
repeatedly.
outlet, then plug it back into the outlet and turn on
the projector again. Contact the Canon Customer
Support Center if the same warning occurs
again.
208
Troubleshooting
Symptoms and Solutions
■ You Cannot Turn on the Projector
Cause
The power cord is not
connected correctly.
The power cord has just
been connected.
The safety device is
activated because the air
intake or the exhaust
vent is blocked and the
internal temperature of
the projector has
increased.
The air filter is not
installed correctly.
Key lock is enabled.
Countermeasure
Check whether the power cord is connected
correctly. (P51)
Wait at least one second after plugging the projector
in until you press the POWER button. You cannot
turn the projector on immediately after plugging it in.
(P52)
When the safety device is active, the [POWER]
indicator does not turn on when you connect the
power cord. You cannot disable this safety device.
Remove any obstacle that is blocking the air intake or
exhaust vent and contact the Canon Customer
Support Center.
Check whether the air filter is installed correctly.
(P194)
Check that Key lock (P121) is not enabled for the
projector or the remote control.
■ You Cannot Project an Image from the Projector
Cause
A cable is not connected
correctly.
20 seconds have not
elapsed since the
projector was turned on.
Check that the same input signal has been correctly
selected for the connected AV equipment from the
[INPUT] menu. (P55)
209
Troubleshooting
Check whether the selected input signal type is
correct. (P55, P198)
Other Information
No image is sent from
the AV equipment.
Connection with the
input terminal has not
been performed
correctly.
No input signal type has
been selected for the
connected AV
equipment.
The input signal type is
incorrect.
Countermeasure
Check whether the projector is connected to the
computer or AV equipment correctly. (P44, P45)
When the projector is turned on, the opening window
is displayed for approximately 20 seconds. To project
an image immediately, press the OK button on the
remote control or side control. (P29, P33)
Check whether an image is played on the connected
video camcorder, DVD, etc.
Check whether the AV equipment is connected to the
projector input terminal correctly. (P32)
Troubleshooting
Cause
The BLANK function has
been selected.
No image is projected
due to a problem with
the computer.
The external monitor
output is not set on the
notebook computer
correctly.
The displayed image is
not the same as that
displayed on the
computer.
Countermeasure
Press the BLANK button on the remote control.
(P72)
Turn first the projector and then the computer off and
then back on again.
Turn on the external monitor output on the notebook
computer. To turn on the external monitor output,
press the [LCD] or [VGA] function key or a key with
an icon for the external monitor, while holding down
the [Fn] key on the keyboard of the notebook
computer. With Windows 10 / Windows 8.1 /
Windows 8 / Windows 7, you can turn on image
output by holding down the Windows logo key and
pressing the [P] key. (P54)
The combination of keys used to perform this
operation varies depending on the model of
notebook computer. For more detailed information,
refer to the manual that came with your computer.
Check whether the dual screen (multi-display) mode
is selected on the computer. If dual screen mode is
selected, change the computer display output to
mirroring mode.
The output setting method varies among computer
manufacturers. For more detailed information, refer
to the manual that came with your computer.
■ There is no Sound
Cause
The audio cable is not
connected correctly.
The MUTE function is
enabled.
The volume level is
adjusted to the
minimum.
An audio cable with a
built-in resistor is used.
Audio in terminal select
is [Off].
Countermeasure
Check the audio cable connection. (P44, P45)
Press the MUTE button on the remote control. (P34)
Press the VOL button on the remote control or the
VOL+ button on the side control to adjust the volume
level. (P29, P34)
Use an audio cable without a built-in resistor.
Change the Audio In terminal to the appropriate
setting. (P123)
210
Troubleshooting
■ The Projected Image Is Blurred
Cause
The image is out of
focus.
The distance to the
screen is too short.
The projector is not
placed straight in front of
the screen.
The projector has been
moved to a place where
the temperature varies a
lot.
The lens is stained.
Video is blurred.
Motion blur reduction is
not available.
Countermeasure
Adjust the focus. (P59)
Check whether the distance to the screen is
appropriate. (P40)
Check whether the projector is placed obliquely to
the screen. A slight error in the projection angle can
be corrected through the keystone adjustment
function. (P65)
When the projector is moved from a location where
the temperature is low to a location where the
temperature is high, condensation may form on the
lens. The condensation will evaporate after a period
of time and the projector will be able to project a
normal image.
Clean the lens. (P194)
Activate motion blur reduction. (P125)
Motion blur reduction is not available in DICOM SIM
image mode.
■ You Cannot Project an Image Appropriately
Cause
The projected image is
inverted in the vertical or
horizontal direction.
A computer cable is
used in which some pins
are not connected.
Countermeasure
The ceiling mounted / rear projection setting is
incorrect. Check the [Image flip H/V] setting in the
[Install settings] menu. (P107)
Use a computer cable in which all pins are
connected.
■ The Projector Power Turns Off
211
Troubleshooting
Countermeasure
Check whether the air intake or exhaust vent is
blocked. If the air intake or exhaust vent is blocked,
the temperature inside the projector will increase and
the power is automatically turned off to protect the
projector. (The [WARNING] indicator and [TEMP]
indicator are lit.) Wait until the projector temperature
drops, then make sure that the intake and exhaust
vents (P28) are not blocked and turn on the projector.
(P52)
Other Information
Cause
The air intake or exhaust
vent is blocked.
Troubleshooting
Cause
The air filter is dirty.
The operating
environment is
inappropriate.
Countermeasure
Check whether the air filter is clogged with dust.
If the air filter is clogged, replace the air filter. (P194)
Check whether the operating temperature is between
0°C (32°F) and 45°C (113°F). (P21)
Projector settings must be adjusted when using the
projector at altitudes of 2,300 m (7,545.8') or higher.
In the [Install settings] menu, set [High altitude] under
[Professional settings] to [On]. (P111)
■ The Projector Cannot Join the Network
Cause
The LAN cable (shielded
twisted pair) is not
connected correctly.
The projector has not
been on long enough
(less than about 40
seconds).
The projector cannot join
a wireless network.
Countermeasure
Check whether the LAN cable (shielded twisted pair)
is connected to the projector correctly. (P135)
Network connections are not available until about 40
seconds after startup. Wait at least 40 seconds, and
then try to connect again. (P160)
Follow the instructions in “Network Setting” (P161 –
P162), “Wireless LAN (Wi-Fi)” (P138), and “Detailed
settings (wireless)” (P147 – P151) to set up the
projector again. In PJ AP mode, try changing the
wireless channel on the projector (P147 – P148). In
infrastructure mode, try changing the wireless
channel on the access point. If connection is still not
possible, contact the Canon Customer Support
Center.
■ You Cannot Operate the Remote Control
Cause
Countermeasure
Batteries are not
installed properly or they
have run out.
You are operating the
remote control from the
outside of the remote
control operating range.
There is an obstacle
between the projector
and the remote control.
Check whether batteries are installed correctly. If
batteries are installed correctly, replace them with
new batteries. (P35)
Check whether you are operating the remote control
within the remote control operating range of the main
unit of the projector. (P36)
Remove the obstacle between the infrared remote
receiver of the main unit of the projector and the
remote control or point the remote control in an
obstacle-free path.
212
Troubleshooting
Cause
Countermeasure
You are operating the
remote control in an
unsuitable operating
environment.
The channel setting of
the remote control does
not match the setting of
the projector.
The key lock function is
preventing operation of
the remote control.
Check whether the infrared remote receiver of the
main unit of the projector is exposed to direct sunlight
or strong light of lighting apparatus. (P36)
Check whether the channel setting of the remote
control has been changed. You can check the
[Remote control channel] setting in the [System
settings] menu. (P122)
Check whether [Key lock] is enabled to disable the
remote control operation.
In the [System settings] menu, set [Key lock] to [Off].
(P121)
Other Information
Troubleshooting
213
Index
Numerics
G
6-axis color adjust ........................... 103
Gamma .............................................99
A
H
Adjusting keystone distortion ............ 65
Air filter...................................... 28, 194
Ambient light ................................... 101
AMX Device Discovery ................... 153
ASPECT............................................ 64
Aspect ............................................... 64
AUDIO IN terminal ............................ 32
AUDIO OUT terminal ........................ 32
Auto (Aspect) .................................... 64
HDMI terminal .......................32, 44, 45
I
IMAGE...............................................69
Image adjustment........................76, 97
Image mode (Image quality) .............68
Information ................................76, 155
INPUT ...............................................55
Input signal select .............................55
Input terminal ....................................32
B
K
BLANK .............................................. 72
Brightness ......................................... 99
Key lock...........................................121
KEYSTONE....................................... 65
Keystone ...........................................65
C
Ceiling mounted ........................ 39, 107
Connecting to AV equipment ............ 45
Contrast ............................................ 99
Corner Adjustment ............................ 66
Crestron RoomView........................ 153
L
LAN port ............................................32
Language ........................................126
LED indicator.............................30, 208
Lens shift .....................................42, 62
D
Digital PC / DVI-D terminal ............... 32
Direct power on............................... 125
Display resolution (Preparing the
computer) ....................................... 57
Dynamic gamma ............................. 102
M
E
N
Edge blending ..................... 4, 112, 183
Effect of ambient light ..................... 101
Network password...........................141
Network settings........................76, 135
Noise reduction ...............................101
Memory color correction..................103
MENU................................................76
Menu ................................................. 76
Multi input ..................................47, 108
F
FREEZE............................................ 72
214
Index
O
Wired Networks ...............................142
Wireless Networks .......... 136, 142, 147
OK............................................... 29, 33
Optical zoom ..................................... 60
P
Password ................................ 127, 128
PJLink ..................................... 152, 177
POWER ...................................... 52, 71
Projecting from Multiple Projectors at
Once (Edge Blending) .................. 183
Projector on..................................... 118
R
Rear projection.......................... 39, 107
Remote control.............. 33, 34, 35, 122
Reset................................. 67, 105, 134
S
Screen color.................................... 115
Selecting a language ................ 53, 126
Setting display status .................. 76, 92
Sharpness......................................... 99
Side control ....................................... 29
Signal type ...................................... 198
Super white ....................................... 93
System settings......................... 76, 117
T
Test pattern ..................................... 197
True size (Aspect) ............................. 64
Turning on external monitor output ... 54
U
USB port ........................................... 32
Index
W
WARNING indicator .................. 30, 208
Wi-Fi.................................................... 5
215
Option
• Ceiling attachment
Part No.: RS-CL15
• Ceiling-mount arm
Part No.: RS-CL17
• Ceiling-mount pipe
(400 - 600 mm / 15.7 - 23.6 in)
Part No.: RS-CL08*
• Ceiling-mount pipe
(600 - 1000 mm / 23.6 - 39.4 in)
Part No.: RS-CL09*
• Air filter
Part No.: RS-FL04
• Remote control
Part No.: RS-RC05
• Remote control
Part No.: RS-RC04
* Use the above materials to hang the projector from the ceiling.
* For ceiling mounting, both ceiling attachment (RS-CL15) and ceiling-mount arm (RS-CL17)
are required.
216
CANON INC.
30-2, Shimomaruko 3-chome, Ohta-ku, Tokyo 146-8501, Japan
CANON U.S.A. INC.
One Canon Park, Melville, New York 11747, U.S.A.
For all inquires concerning this product, call toll free in the U.S. 1-800-OK-CANON
CANON EUROPE LTD.
3 The Square, Stockley Park, Uxbridge, Middlesex, UB11 1ET United Kingdom
CANON EUROPA N.V.
Bovenkerkerweg 59, 1185 XB Amstelveen, The Netherlands
YT1-7491-000
©CANON INC.2017
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement