Intel IB850 User's Manual

Intel IB850 User's Manual
IB850
Socket 478 Pentium 4
Intel 875P Chipset
Full Size CPU Card
USER’S MANUAL
Version 1.0
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Pentium 4 are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
ii
IB850 User’s Manual
Table of Contents
Introduction .............................................................. 1
Checklist ........................................................................1
Product Description ........................................................2
Specifications .................................................................3
Board Dimensions...........................................................5
Installations .............................................................. 7
Installing the CPU...........................................................8
ATX Power Installation...................................................9
Installing the Memory......................................................9
Setting the Jumpers....................................................... 10
Connectors on IB850 .................................................... 18
BIOS Setup ..............................................................33
Drivers Installation............................................56
Intel 875P Chipset Software Intallation Utility ................. 57
Realtek AC97 Codec Audio Driver Installation ............... 60
Intel PRO LAN Drivers Installation ............................... 61
ATI M7 VGA Driver Installation ................................... 62
ATI M9/M10 VGA Driver Installation ........................... 64
IB850 User’s Manual
iii
This page is intentionally left blank.
iv
IB850 User’s Manual
INTRODUCTION
Introduction
Checklist
Your IB850 Pentium 4 CPU card package should include the items listed
below:
• The IB850 CPU Card
• This User’s Manual
• 1 IDE Ribbon Cable
• 1 Floppy Ribbon Connector
• SATA Power Cord
• SATA Cable
• 2 Serial Port Ribbon Cable and 1 Parallel Port Attached to a
Mounting Bracket
• 1 Y-Cable supporting a PS/2 Keyboard and a PS/2 Mouse
• 1 CD containing the following:
• Chipset Drivers
• Flash Memory Utility
• Optional audio cable with bracket (Audio8K)
• Optional USB cable with bracket (USB2K-4)
• Optional Secondary CRT VGA cable with bracket (VGA4K, for use
with IBA110)
• Optional TMDS cable with bracket (ID120P, for use with IBA110)
• Optional MicroAGP cards (IBA110)
IB850 User’s Manual
1
INSTALLATIONS
Product Description
The IB850 Pentium 4 CPU card incorporates the Intel 875P chipset that can
utilize a single PGA478 processor of up to 3.2GHz or higher and supports
FSB frequency of 400/533/800Mhz (100Mhz, 133Mhz, and 200Mhz HCLK
respectively).
The 875P chipset comes with a Memory Controller Hub (MCH) designed
for use with the Pentium 4 processor with 512-KB L2 cache on 0.13 micron
process. The MCH component provides the CPU interface, DDR
interface, Hub Interface, and AGP8X graphics interface.
Aside from CRT support, the VGA function feature a Micro AGP slot for
optional daughter cards:
IBA110: with ATI M7CSP32, M9CSP64 / M10CSP64 chipset,
64MB/32MB frame buffer and supports dual channel LVDS interface,
TMDS and CRT2 display function.
Two DDR memory sockets support up to 2GB DDR 266/333/400
ECC/non-ECC SDRAM.
The board also has an Intel 82551 10/100MB fast Ethernet LAN and
optional Intel 82547EI Gigabit LAN as secondary LAN.
Other advanced features include two Serial ATA ports, four USB 2.0
ports, IrDA interface and audio function.
2
IB850 User’s Manual
INTRODUCTION
Specifications
Product Name
Form Factor
CPU Type
CPU Voltage
System Speed
CPU Frequency
Green /APM
CPU Socket
Chipset
BIOS
Cache
VGA
Primary LAN
Secondary LAN
Audio
Memory type
LPC I/O
RTC/CMOS
Battery
PS2 KB/Mouse
Local bus IDE
Serial ATA
PCI to ISA
Bridge
ISA High drive
USB
IrDA
Disk On Chip
Watchdog
Timer
Expansion slots
D-type
connector
Power
IB850
PICMG (full size CPU card)
Socket 478 (Intel Pentium 4)
0.8375V~1.6V (VRD 10)
2.0G~3.2GHz
400 MHz/533MHz/800MHz
APM1.2
Socket 478
Intel 875P Chipset
MCH: 82875P 932 pin FC-BGA
ICH5R: 82801ER 460 pin MBGA
Award BIOS, support ACPI Function
128K/256K/512K Level 2 (CPU integrated)
MicroAGP daughter card w/ ATI Mobility M7/ M9 / M10
graphics controller, embedded 32/64MB Frame buffer
(DDR), AGP 4X, support CRT, LVDS, TV-out / 2nd CRT.
Intel 82551QM LAN controller (10/100Mb)
Intel 82547EI (10/100/1000Mb) Gigabit LAN (optional)
ICH5R Built-in Sound controller + AC97 Codec ALC650, 2x6
12 pin header (Line-out, Line-in, MIC.). Supports 5.1
channels.
2 x DDR 2.5V PC266/333/400 DDR SDRAM (support ECC
Function) DIMM Module, Max. capacity - 2GB
Winbond 83627HF: IrDAx1 Parallel x1, COM1 (RS-232),
COM2 (RS-232/RS422/RS485), FDC 2.88MB (3 Mode
Support), Hardware monitoring
ICH5R Built-in
Lithium Battery
Controller built in Winbond 83627HF
ICH5R built in, IDE1, IDE2 (Ultra DMA 33/66/100)
2 ports
ITE 8888
Supported by SN74ABT16245
4 ports, USB 2.0
Pin header
Supports up to 288MB capacity
Yes (256 segments: 0,1,2,...255 sec/min)
MicroAGP VGA socket for IBA110
PS/2 keyboard/mouse, VGA (CRT), RJ-45 x 2
ATX 12V
IB850 User’s Manual
3
INSTALLATIONS
Connector
System
Voltages
Board Size
Other Features
4
+5V, +12V, -12V, 5VSB
122 x 338 mm
Modem Wakeup, LAN Wakeup
IB850 User’s Manual
0" [0.00]
0.2" [5.08]
0.856" [21.74]
3.196" [81.18]
3.792" [96.32]
4.362" [110.79]
12.372" [314.25]
4.8" [121.92]
6]
4.0
"[O
.16
O0
0.865" [21.97]
3.133" [79.58]
6]
4.0
"[O
.16
O0
0.987" [25.07]
4.6" [116.84]
6]
4.0
"[O
.16
O0
0" [0.00]
0.7" [17.78]
1.454" [36.93]
2.124" [53.95]
2.562" [65.07]
3.054" [77.57]
3.546" [90.07]
3.95" [100.33]
4.8" [121.92]
INTRODUCTION
Board Dimensions
IB850 User’s Manual
5
0.2" [5.08]
0" [0.00]
1.948" [49.48]
6.087" [154.61]
6.712" [170.48]
9.372" [238.05]
9.762" [247.95]
13.117" [333.17]
13.317" [338.25]
INSTALLATIONS
6
IB850 User’s Manual
INSTALLATIONS
Installations
This section provides information on how to use the jumpers and
connectors on the IB850 in order to set up a workable system. The topics
covered are:
Installing the CPU...........................................................8
ATX Power Installation...................................................9
Installing the Memory......................................................9
Setting the Jumpers....................................................... 10
Connectors on IB850 .................................................... 18
IB850 User’s Manual
7
INSTALLATIONS
Installing the CPU
The IB850 CPU card supports a Socket 478 processor socket for Intel
Pentium 4 processors.
The Socket 478 processor socket comes with a lever to secure the
processor. Raise this lever to about a 90° angle to allow the insertion of the
processor. Place the processor into the socket by making sure the notch
on the corner of the CPU corresponds with the notch on the inside of the
socket. Once the processor has slide into the socket, return the lever to
the lock position. Refer to the figures below.
After you have installed the processor into the socket, check if the
jumpers for the CPU type and speed are correct.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
8
IB850 User’s Manual
INSTALLATIONS
ATX Power Installation
The system power is provided to the CPU card with the CN1 and J7 ATX
power connectors. Please note that the J7 external ATX power connector
should be connected to the backplane for IB850 to function. J7 is a 3-pin
power connector. CN1 is a 4-pin 12V power connector. CN1 is to be
connected to the ATX power supply.
Installing the Memory
The IB850 CPU card supports two DDR memory sockets for a maximum
total memory of 2GB in DDR memory type. You can install unbuffered
DDR DIMMs with ECC function. It supports DDR266 when installed with
CPUs that have clock speeds of 400MHz. It supports DDR266/333 when
installed with CPUs that have clock speeds of 533MHz. It supports
DDR266/333/400 when installed with CPUs that have clock speeds of
800MHz. The board provides dual channel functionality for its DIMM
slots. DIMM1 is for one channel and DIMM2 is for the other channel.
Enabling dual channels can increase data access rates.
Basically, the system memory interface has the following features:
Supports two 64-bit wide DDR data channels
Available bandwidth up to 3.2GB/s (DDR400) for single-channel
mode and 6.4GB/s (DDR400) in dual-channel mode.
Supports ECC/ non-ECC DIMMs.
Supports 128MB, 256MB, 512MB DDR technologies.
Supports only x8, x16, DDR devices with four banks
Registered DIMMs not supported
Supports opportunistic refresh
Up to 16 simultaneously open pages (four per row, four rows
maximum)
IB850 User’s Manual
9
INSTALLATIONS
Setting the Jumpers
Jumpers are used on IB850 to select various settings and features
according to your needs and applications. Contact your supplier if you
have doubts about the best configuration for your needs. The following
lists the connectors on IB850 and their respective functions.
Jumper Locations on IB850....................................................................11
JP1: Clear CMOS Contents ....................................................................12
JP2, JP3, JP4: RS232/422/485 (COM2) Selection .................................12
JP6: 82551 10/100Mb LAN Enable/Disable..........................................12
JP7: DiskOnChip Address Select..........................................................13
JP9: AT/ATX Power Supply Select......................................................13
Jumper and Connectors on IBA110......................................................14
J1: TMDS Panel Connector....................................................................14
J2: CRT2 / TV-Out Connector................................................................14
J3: Panel Inverter Power Connector......................................................15
J4: VGA Chipset Fan Power Connector...............................................15
J5, J6: LVDS Connectors (2nd channel, 1st channel).........................15
JP1: LVDS Panel Power Select...............................................................15
SW1: LVDS Resolution Select...............................................................17
10
IB850 User’s Manual
INSTALLATIONS
Jumper Locations on IB850
J19
J20
J21
J5
J15
J12
J4
J2
J11
JP1: Clear CMOS Contents
JP2, JP3, JP4: RS232/422/485
(COM2) Selection
JP6: 82551 10/100Mb LAN
Enable/Disable
JP7: DiskOnChip Address Select
JP9: AT/ATX Power Supply Select
FDD1
J13
IDE2
J14
J6
IDE1
J9
JP7
BAT1
CN2
J7
CN3
AGP1
J8
RT2
DIMM2
DIMM1
JP8
J1
BZ1
CN1
J3
Jumper Locations on IB850
IB850 User’s Manual
11
INSTALLATIONS
JP1: Clear CMOS Contents
Use JP1, a 3-pin header, to clear the CMOS contents. Note that the
ATX-power connector should be disconnected from the CPU card before
clearing CMOS.
JP1
Setting
Function
Pin 1-2
Short/Closed
Normal
Pin 2-3
Short/Closed
Clear CMOS
JP2, JP3, JP4: RS232/422/485 (COM2) Selection
J4, COM1 is fixed for RS-232 use only.
J5, COM2 is selectable for RS232, RS-422 and RS-485.
The following table describes the jumper settings for COM2 selection.
COM2
Function
Jumper
Setting
(pin closed)
RS-232
RS-422
RS-485
JP2:
1-2
JP2:
3-4
JP2:
5-6
JP3:
3-5 & 4-6
JP3:
1-3 & 2-4
JP3:
1-3 & 2-4
JP4:
3-5 & 4-6
JP4:
1-3 & 2-4
JP4:
1-3 & 2-4
JP6: 82551 10/100Mb LAN Enable/Disable
JP6
Function
Enable LAN
Disable LAN
12
IB850 User’s Manual
INSTALLATIONS
JP7: DiskOnChip Address Select
JP7
Address
D0000-D7FFF
D8000-D9FFF (default)
JP9: AT/ATX Power Supply Select
JP9
Function
ATX power supply
AT power supply
IB850 User’s Manual
13
INSTALLATIONS
Jumper and Connectors on IBA110
J1: TMDS Panel Connector
J2: CRT2 / TV-Out Connector
J3: Panel Inverter Power Connector
J4: VGA Chipset Fan Power Connector
J5, J6: LVDS Connectors (2nd channel, 1st
channel)
JP1: LVDS Panel Power Select
SW1: LVDS Resolution Select
J1: TMDS Panel Connector
TMDS stands Transition Minimized Differential Signaling.
J1
Signal Name
TX1P
TXIN
GND
GND
TXCP
TXCN
GND
+5v
HTPG
NC
Pin #
1
2
3
4
5
6
7
8
9
10
Pin #
11
12
13
14
15
16
17
18
19
20
Signal Name
TX2P
TX2N
GND
GND
TX0P
TX0N
NC
NC
DDCDATA
DDCCLK
J2: CRT2 / TV-Out Connector
This connector is used for a second CRT monitor or use with a TV output device.
J2
14
Signal Name
Red / C
Green / Y
Blue / COMP
N.C.
Ground
Ground
Ground
Ground
Pin # Pin #
1
9
2
10
3
11
4
12
5
13
6
14
7
15
8
16
IB850 User’s Manual
Signal Name
+5V
Ground
N. C.
CRT2 DDCDAT
HSYNC
VSYNC
CRT2 DDCCLK
N.C.
INSTALLATIONS
J3: Panel Inverter Power Connector
The connector supports 1A current (maximum).
Pin #
1
2
3
Signal Name
+12V
NC
Ground
J4: VGA Chipset Fan Power Connector
Pin #
1
2
Signal Name
+12V
Ground
J5, J6: LVDS Connectors (2nd channel, 1st channel)
The LVDS connectors, DF13 20-pin mating connectors, are composed of
the first channel (J6) and second channel (J5) to support 24-bit or 48-bit.
Signal Name
Pin #
Pin #
TX02
1
Ground
4
3
TX16
5
5V/3.3V
8
7
TX310
9
TX212
11
Ground
14
13
TXC16
15
5V/3.3V
18
17
+12V
20
19
Remarks: Maximum current for +12V is 1A.
Signal Name
TX0+
Ground
TX1+
Ground
TX3+
TX2+
Ground
TXC+
ENABKL
+12V
JP1: LVDS Panel Power Select
JP1
Setting
Panel Voltage
Pin 1-2
Short/Closed
3.3V (default)
Pin 2-3
Short/Closed
5V
IB850 User’s Manual
15
INSTALLATIONS
16
IB850 User’s Manual
INSTALLATIONS
SW1: LVDS Resolution Select
SW1-1
OFF
ON
OFF
SW1-2
ON
OFF
OFF
SW1-3
ON
ON
ON
Resolution
800x600 18 bit
1024x768 18bit
1024x768 24 bit
IB850 User’s Manual
17
INSTALLATIONS
[
Connectors on IB850
The connectors on IB850 allows you to connect external devices such as
keyboard, floppy disk drives, hard disk drives, printers, etc. The following
table lists the connectors on IB850 and their respective functions.
Connector Locations on IB850..............................................................19
IDE1, IDE2: EIDE Connectors................................................................19
FDD1: Floppy Drive Connector............................................................21
CN1: ATX 12V/+12V Power Connector...............................................21
CN2, CN3: USB Connectors...................................................................21
J3: CPU Fan Power Connector...............................................................22
J7: External ATX Power Connector......................................................22
J8, J9: System Fan Power Connector....................................................22
J1: System Function Connector............................................................23
J2: Parallel Port Connector .....................................................................25
J4, J5: COM1 and COM2 Serial Ports Connector................................25
J10: Wake On LAN Connector..............................................................26
J11: External Audio Connector..............................................................26
J12: CD-In Audio Connector .................................................................26
J13, J14: Serial ATA (SATA) Connectors ...........................................26
J15: VGA CRT Connector.......................................................................27
J16, J18: External PS/2 Mouse and Keyboard Connector..................27
J17: IrDA Connector...............................................................................27
J19: PS/2 Keyboard and Mouse Connector........................................28
J20: Primary RJ45 Connector..................................................................28
J21: Gigabit LAN RJ45 Connector.........................................................28
AGP1: MicroAGP Connector (for IBA110)..........................................28
18
IB850 User’s Manual
INSTALLATIONS
Connector Locations on IB850
J15
J19
J20
J21
J5
JP2~JP4
J12
J2
J16
J18
J17
JP13
JP5~JP11
J4
JP12
J11
J13
FDD1
J14
J6
IDE1, IDE2: EIDE Connectors
J10
AGP1
JP1
J9
IDE1
J8
CN3
J7
CN2
BAT1
JP14
JP15
RT3
IDE2
J1
DIMM1
BZ1
CN1
DIMM2
Connector Locations on IB850
IDE1, IDE2: EIDE Connectors
FDD1: Floppy Drive Connector
CN1: ATX 12V/+12V Power
Connector
CN2, CN3: USB Connectors
J3: CPU Fan Power Connector
J7: External ATX Power
Connector
J8, J9: System Fan Power
Connector
J1: System Function Connector
J2: Parallel Port Connector
J4, J5: COM1 and COM2 Serial
Ports Connector
J10: Wake On LAN Connector
J11: External Audio Connector
J12: CD-In Audio Connector
J13, J14: Serial ATA (SATA)
Connectors
J15: VGA CRT Connector
J16, J18: External PS/2 Mouse and
Keyboard Connector
J17: IrDA Connector
J19: PS/2 Keyboard and Mouse
Connector
J20: Primary RJ45 Connector
J21: Gigabit LAN RJ45 Connector
AGP1: MicroAGP Connector (for
IBA110)
J3
IB850 User’s Manual
19
INSTALLATIONS
IDE1
IDE2
20
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ0
Host IOW
Host IOR
IOCHRDY
DACK0
IRQ14
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
Signal Name
Reset IDE
Host data 7
Host data 6
Host data 5
Host data 4
Host data 3
Host data 2
Host data 1
Host data 0
Ground
DRQ1
Host IOW
Host IOR
IOCHRDY
DACK1
IRQ15
Address 1
Address 0
Chip select 0
Activity
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
35
37
39
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
36
38
40
Signal Name
Ground
Host data 8
Host data 9
Host data 10
Host data 11
Host data 12
Host data 13
Host data 14
Host data 15
Protect pin
Ground
Ground
Ground
Host ALE
Ground
No connect
No connect
Address 2
Chip select 1
Ground
IB850 User’s Manual
INSTALLATIONS
FDD1: Floppy Drive Connector
FDD1 is a 34-pin header and will support up to 2.88MB floppy drives.
FDD1
Signal Name
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Pin #
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
Pin #
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
Signal Name
RM/LC
No connect
No connect
Index
Motor enable 0
Drive select 1
Drive select 0
Motor enable 1
Direction
Step
Write data
Write gate
Track 00
Write protect
Read data
Side 1 select
Diskette change
CN1: ATX 12V/+12V Power Connector
Pin #
1
2
3
4
Signal Name
Ground
Ground
+12V
+12V
CN2, CN3: USB Connectors
The following table shows the pin outs of the USB pin headers
connectors. Overall, the two pin headers support four USB ports.
CN2
Signal Name
Vcc
USB0USB0+
Ground
Pin
1
2
3
4
Pin
5
6
7
8
IB850 User’s Manual
Signal Name
Ground
USB1+
USB1Vcc
21
INSTALLATIONS
CN3
Signal Name
Vcc
USB2USB2+
Ground
Pin
1
2
3
4
Pin
5
6
7
8
Signal Name
Ground
USB3+
USB3Vcc
J3: CPU Fan Power Connector
J3 is a 3-pin header for the CPU fan. The fan must be a 12V fan.
Pin #
1
2
3
Signal Name
Ground
+12V
Rotation detection
J7: External ATX Power Connector
Pin #
1
2
3
Signal Name
Ground
PS-ON (soft on/off)
5VSB (Standby +5V)
J8, J9: System Fan Power Connector
J8 and J9 are 3-pin headers for system fans. The fan must be a 12V fan.
Pin #
1
2
3
22
Signal Name
Ground
+12V
Rotation detection
IB850 User’s Manual
INSTALLATIONS
J1: System Function Connector
J1 provides connectors for system indicators that provide light indication
of the computer activities and switches to change the computer status. J1
is a 20-pin header that provides interfaces for the following functions.
Hard Disk Drive LED
Reset Switch
Not Defined
ATX Power On Switch
SMI / Hardware Switch
Power LED
Speaker
Speaker: Pins 1 - 4
This connector provides an interface to a speaker for audio
tone generation. An 8-ohm speaker is recommended.
Pin #
1
2
3
4
Signal Name
Speaker out
No connect
Ground
+5V
Power LED: Pins 11 - 15
The power LED indicates the status of the main power
switch.
Pin #
11
12
13
14
15
IB850 User’s Manual
Signal Name
Power LED
No connect
Ground
No connect
Ground
23
INSTALLATIONS
SMI/Hardware Switch: Pins 6 and 16
This connector supports the "Green Switch" on the control
panel, which, when pressed, will force the system into the
power-saving mode immediately.
Pin #
Signal Name
6
SMI
16
Ground
ATX Power ON Switch: Pins 7 and 17
This 2-pin connector is an “ATX Power Supply On/Off
Switch” on the system that connects to the power switch on
the case. When pressed, the power switch will force the
system to power on. When pressed again, it will force the
system to power off.
Reset Switch: Pins 9 and 19
The reset switch allows the user to reset the system without
turning the main power switch off and then on again.
Orientation is not required when making a connection to this
header.
Hard Disk Drive LED Connector: Pins 10 and 20
This connector connects to the hard drive activity LED on
control panel. This LED will flash when the HDD is being
accessed.
Pin #
10
20
24
IB850 User’s Manual
Signal Name
HDD Active
5V
INSTALLATIONS
J2: Parallel Port Connector
The following table describes the pin out assignments of this connector.
J2
Signal Name
Line printer strobe
PD0, parallel data 0
PD1, parallel data 1
PD2, parallel data 2
PD3, parallel data 3
PD4, parallel data 4
PD5, parallel data 5
PD6, parallel data 6
PD7, parallel data 7
ACK, acknowledge
Busy
Paper empty
Select
Pin #
1
2
3
4
5
6
7
8
9
10
11
12
13
Pin #
14
15
16
17
18
19
20
21
22
23
24
25
N/A
Signal Name
AutoFeed
Error
Initialize
Select
Ground
Ground
Ground
Ground
Ground
Ground
Ground
Ground
N/A
J4, J5: COM1 and COM2 Serial Ports Connector
J4 and J5 both 10-pin headers, are the onboard serial port connectors.
J4
Fixed as
RS-232
J5
Configurable
as RS-232/
RS-422/485
with jumpers
JP2/JP3/JP4
Pin #
1
2
3
4
5
6
7
8
9
10
Signal Name
RS -232
DCD
RX
TX
DTR
GND
DSR
RTS
CTS
RI
NC
RS -422
TXTX+
RX+
RXGND
RTSRTS+
CTS+
CTSNC
IB850 User’s Manual
RS -485
DATADATA+
NC
NC
GND
NC
NC
NC
NC
NC
25
INSTALLATIONS
J10: Wake On LAN Connector
J10 is a 3-pin header for the Wake On LAN function on the motherboard.
The following table shows the pin out assignments of this connector.
Wake On LAN will function properly only with an ATX power supply
with 5VSB that has 1A.
Pin #
1
2
3
Signal Name
+5VSB
Ground
LAN Wakeup
J11: External Audio Connector
J11 is a 12-pin header that is used to connect to the optional audio cable
that integrates jacks for Line In, Line Out and Mic.
Signal Name
LINEOUT_R
Ground
LINEIN_R
Ground
Mic-In
Ground
Pin #
1
3
5
7
9
11
Pin #
2
4
6
8
10
12
Signal Name
LINEOUT_L
Ground
LINEIN L
Ground
VREFOUT
Protect pin
J12: CD-In Audio Connector
Pin #
1
2
3
4
Signal Name
CD Audio R
Ground
Ground
CD Audio L
J13, J14: Serial ATA (SATA) Connectors
The SATA connectors support serial ATA 150. Each connector can only
use one serial ATA hard disk. J13 is port 1 and J14 is port 2.
26
IB850 User’s Manual
INSTALLATIONS
J15: VGA CRT Connector
The pin assignments of the J15 VGA CRT connector are as follows:
J15
Signal Name
Red
Blue
GND
GND
N.C.
N.C.
HSYNC
NC
Pin
1
3
5
7
9
11
13
15
Pin
2
4
6
8
10
12
14
Signal Name
Green
N.C.
GND
GND
GND
N.C.
VSYNC
J16, J18: External PS/2 Mouse and Keyboard Connector
Pin #
1
2
3
4
5
J16
KB clock
KB data
N.C.
Ground
Vcc
J18
Mouse data
N.C.
Ground
Vcc
Mouse clock
J17: IrDA Connector
J17 is used for an optional IrDA connector for wireless communication.
Pin #
Signal Name
1
+5V
2
No connect
3
Ir RX
4
Ground
5
Ir TX
IB850 User’s Manual
27
INSTALLATIONS
J19: PS/2 Keyboard and Mouse Connector
J19 uses a Y-cable with dual D-connectors for a PS/2 keyboard and a PS/2
mouse.
J19
Pin #
1
2
3
4
5
6
Signal Name
Mouse data
Keyboard data
Ground
Vcc
Mouse Clock
Keyboard Clock
J20: Primary RJ45 Connector
J20 is the primary RJ-45 connector based on the chipset integrated LAN.
The figure below shows the pin out assignments of the connector and its
corresponding input jack.
J21: Gigabit LAN RJ45 Connector
J21 is the Gigabit LAN RJ45 connector.
AGP1: MicroAGP Connector (for IBA110)
28
IB850 User’s Manual
INSTALLATIONS
Watchdog Timer Configuration
The WDT is used to generate a variety of output signals after a user
programmable count. The WDT is suitable for use in the prevention of
system lock-up, such as when software becomes trapped in a deadlock.
Under these sort of circumstances, the timer will count to zero and the
selected outputs will be driven. Under normal circumstance, the user will
restart the WDT at regular intervals before the timer counts to zero.
SAMPLE CODE:
This code and information is provided "as is" without warranty of any
kind, either expressed or implied, including but not limited to the implied
warranties of merchantability and/or fitness for a particular purpose.
;[]================================================
; Name : Enable_And_Set_Watchdog
; IN
: AL - 1sec ~ 255sec
; OUT : None
;[]================================================
Enable_And_Set_Watchdog Proc
Near
push
ax
;save time interval
call Unlock_Chip
mov
cl, 2Bh
call Read_Reg
and
al, NOT 10h
call Write_Reg
;set GP24 as WDTO
mov
cl, 07h
mov
al, 08h
call Write_Reg
;switch to LD8
IB850 User’s Manual
29
INSTALLATIONS
mov
cl, 0F5h
call Read_Reg
and
al, NOT 08h
call Write_Reg
;set count mode as second
pop ax
mov
cl, 0F6h
call Write_Reg
;set watchdog timer
mov
al, 01h
mov
cl, 30h
call Write_Reg
;watchdog enabled
call Lock_Chip
ret
Enable_And_Set_Watchdog Endp
;[]===============================================
; Name : Disable_Watchdog
; IN
: None
; OUT : None
;[]===============================================
Disable_Watchdog Proc
Near
call Unlock_Chip
mov
cl, 07h
mov
al, 08h
call Write_Reg
;switch to LD8
xor al, al
mov
cl, 0F6h
call Write_Reg
;clear watchdog timer
xor al, al
mov
cl, 30h
call Write_Reg
;watchdog disabled
call Lock_Chip
ret
Disable_Watchdog Endp
;[]===============================================
30
IB850 User’s Manual
INSTALLATIONS
; Name : Unlock_Chip
; IN : None
; OUT : None
;[]===============================================
Unlock_Chip Proc
Near
mov
dx, 2Eh
mov
al, 87h
out dx, al
out dx, al
ret
Unlock_Chip Endp
;[]================================================
; Name : Lock_Chip
; IN : None
; OUT : None
;[]================================================
Unlock_Chip Proc
Near
mov
dx, 2Eh
mov
al, 0AAh
out dx, al
ret
Unlock_Chip Endp
;[]================================================
; Name : Write_Reg
; IN : CL - register index
;
AL - Value to write
; OUT : None
;[]================================================
Write_Reg Proc
Near
push
ax
mov
dx, 2Eh
mov
al,cl
out dx,al
pop ax
inc dx
out dx,al
ret
Write_Reg Endp
;[]================================================
IB850 User’s Manual
31
INSTALLATIONS
; Name : Read_Reg
; IN : CL - register index
; OUT : AL - Value to read
;[]===================================================
Read_Reg Proc
Near
mov
al, cl
mov
dx, 2Eh
out dx, al
inc dx
in al, dx
ret
Read_Reg Endp
;[]================================================
32
IB850 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award BIOS
that comes with the CPU card. The topics covered in this chapter are as
follows:
BIOS Introduction................................................................................34
BIOS Setup ............................................................................................34
Standard CMOS Setup.......................................................................36
Advanced BIOS Features.................................................................39
Advanced Chipset Features .............................................................43
Integrated Peripherals ........................................................................46
Power Management Setup ...............................................................49
PNP/PCI Configurations ...................................................................52
PC Health Status ..................................................................................53
Frequency/Voltage Control...............................................................54
Load Fail-Safe Defaults.....................................................................55
Load Setup Defaults ...........................................................................55
Set Supervisor/User Password........................................................55
Save & Exit Setup ...............................................................................55
Exit Without Saving .............................................................................55
IB850 User’s Manual
33
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your computer
system’s ROM supports Intel Pentium 4 processors. The BIOS provides
critical low-level support for a standard device such as disk drives, serial
ports and parallel ports. It also adds virus and password protection as well
as special support for detailed fine-tuning of the chipset controlling the
entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you to
enter the Setup utility. If you are a little bit late pressing the <Del> key,
POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to select,
the <PgUp> and <PgDn> keys to change entries, <F1> for help and <Esc>
to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
34
IB850 User’s Manual
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC : Quit
F10 : Save & Exit Setup
á â à ß : Select Item
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the control
keys section, there is another section, which displays information on the
currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
IB850 User’s Manual
35
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the CPU card is already installed in a working
system, you will not need to select this option. You will need to run the
Standard CMOS option, however, if you change your system hardware
configurations, the onboard battery fails, or the configuration stored in
the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Wed, Nov 5 2003
Time (hh:mm:ss)
00 : 00 : 00
Menu Level
Item Help
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
IDE Channel 2 Master
IDE Channel 3 Master
None
None
None
None
None
None
Change the day, month,
Year and century
Drive A
Drive B
1.44M, 3.5 in.
None
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
Total Memory
640K
1024K
2048K
>
At the bottom of the menu are the control keys for use on this menu. If you
need any help in each item field, you can press the <F1> key. It will display
the relevant information to help you. The memory display at the lower
right-hand side of the menu is read-only. It will adjust automatically
according to the memory changed. The following describes each item of
this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
Sun to Sat
1 to 12
1 to 31
1994 to 2079
To set the date, highlight the “Date” field and use the PageUp/ PageDown
or +/- keys to set the current time.
36
IB850 User’s Manual
BIOS SETUP
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn> or
+/- keys to set the current time.
IDE Primary HDDs / IDE Secondary HDDs
The onboard PCI IDE connectors provide Primary and Secondary
channels for connecting up to four IDE hard disks or other IDE devices.
Each channel can support up to two hard disks; the first is the “Master”
and the second is the “Slave”.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
CYLS :
HEAD :
PRECOMP :
LANDZ :
SECTOR :
Number of cylinders
Number of read/write heads
Write precompensation
Landing zone
Number of sectors
The Access Mode selections are as follows:
Auto
Normal (HD < 528MB)
Large (for MS-DOS only)
LBA (HD > 528MB and supports
Logical Block Addressing)
Remarks: The main board supports two serial ATA ports and are
represented in this setting as IDE Channel 2 / 3 Master.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB
1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in.
3.5 in.
3.5 in.
3.5 in.
IB850 User’s Manual
37
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
38
IB850 User’s Manual
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and allows
you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
Hard Disk Boot Priority
CPU L1 and L2 Cache
Hyper-threading Technology
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up Numlock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
Press Enter
Enabled
Enabled
Enabled
Floppy
Hard Disk
CD-ROM
Enabled
Disabled
Disabled
On
Fast
Disabled
6
250
Setup
Enabled
1.4
Non-OS2
Yes
Enable
ITEM HELP
Menu Level >
Select Hard Disk Boot
Device Priority
Hard Disk / CD-ROM Boot Priority
This item allows you to set the priority for hard disk boot. When you press enter,
the selections shows the current hard disks used in your system as well as the
“Bootable Add-in Card” that is relevant to other boot sources media such as SCSI
cards and LAN cards.
CPU L1 and L2 Cache
Cache memory is additional memory that is much faster than conventional
DRAM (system memory). CPUs from 486-type on up contain internal cache
memory, and most, but not all, modern PCs have additional (external) cache
memory. When the CPU requests data, the system transfers the requested data
from the main DRAM into cache memory, for even faster access by the CPU.
These items allow you to enable (speed up memory access) or disable the cache
function. By default, these items are Enabled.
Hyper-Threading Technology
This feature is enabled when your processor supports Hyper-Threading
Technology. Otherwise, this field will be hidden.
Quick Power On Self Test
IB850 User’s Manual
39
BIOS SETUP
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some items.
40
IB850 User’s Manual
BIOS SETUP
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include Floppy, LS/ZIP, HDD-0,
SCSI, CDROM, HDD-1, HDD-2, HDD-3, LAN and Disable.
Boot Other Device
These fields allow the system to search for an operating system from other
devices other than the ones selected in the First/Second/Third Boot
Device.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default, this
field is set to Disabled.
Boot Up Floppy Seek
This feature controls whether the BIOS checks for a floppy drive while
booting up. If it cannot detect one (either due to improper configuration or
its absence), it will flash an error message.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up the
system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
IB850 User’s Manual
41
BIOS SETUP
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for your operating system. MPS version 1.4 added extended configuration
tables to improve support for multiple PCI bus configurations and
improve future expandability. The default setting is 1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
If you are using Windows 95/98 without a floppy disk drive, select
Enabled to release IRQ6. This is required to pass Windows 95/98's SCT
test. You should also dis able the Onboard FDC Controller in the
Integrated Peripherals screen when there's no floppy drive in the system.
If you set this feature to Disabled, the BIOS will not report the missing
floppy drive to Win95/98.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Enabled.
42
IB850 User’s Manual
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
Active to Precharge Delay
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Memory Frequency For
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole at 15M-16M
Delay Prior to Thermal
AGP Aperture Size (MB)
Init Display First
DRAM Date Integrity Mode
By SPD
2
8
4
4
Auto
Enabled
Enabled
Disabled
16 Min
128
PCI Slot
Non-ECC
ITEM HELP
Menu Level >
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can select CAS latency time in HCLKs of 2/2 or 3/3. The system board
designer should set the values in this field, depending on the DRAM
installed. Do not change the values in this field unless you change
specifications of the installed DRAM or the installed CPU. The choices
are 2 and 3.
Active to Precharge Delay
The default setting for the Active to Precharge Delay is 6.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the delay
improves the performance of the SDRAM.
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to accumulate
its charge before the SDRAM refreshes. The default setting for the Active
to Precharge Delay is 3.
Memory Frequency For
IB850 User’s Manual
43
BIOS SETUP
This field sets the frequency of the DRAM memory installed. The default
setting is Auto. The other settings are PC200 and PC266.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if any
program writes to this memory area, a system error may result.
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However, if any
program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be reserved
for ISA cards. This memory must be mapped into the memory space below
16 MB. The choices are Enabled and Disabled.
Delay Prior to Thermal
This field activates the CPU thermal function after the systems boots for
the set number of minutes. The options are 16Min and 64Min.
AGP Aperture Size
The field sets aperture size of the graphics. The aperture is a portion of the
PCI memory address range dedicated for graphics memory address space.
Host cycles that hit the aperture range are forwarded to the AGP without
any translation. The default setting is 128M.
Init Display First
This field allows the system to initialize first the VGA on chip or the
display card on the PCI Slot.
On-Chip VGA
By default, the On-Chip VGA or 875P chipset-integrated VGA is Enabled.
On-Chip Frame Buffer Size
The On-Chip Frame Buffer Size can be set us 1MB, 8MB or 16MB. This
memory is shared with the system memory.
Boot Display
44
IB850 User’s Manual
BIOS SETUP
Boot Display determines the display output device where the system
boots. The default setting is LVDS.
Panel Scaling
With the default setting of Auto, this item automatically displays the
resolution of the panel used in the system to ‘full’ screen.
Panel Number
By default, this item is set to 800 x 600 LVDS. If you are using other kinds
of panel, enter this field to select the one that suits your panel.
TV Standard
By default, this item is set to off.
Video Connector
By default, this item is set to Automatic.
TV Format
By default, this item is set to Auto.
IB850 User’s Manual
45
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
On-Chip Primary IDE Device
Onboard Device
SuperIO Device
Press Enter
Press Enter
Press Enter
ITEM HELP
Menu Level >
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE Block Mode
IDE DMA transfer access
On-Chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
Enabled
Enabled
Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
ITEM HELP
Menu Level >>
If your IDE hard drive
supports block mode
select Enabled for
automatic detection of
the optimal number of
block read/write per
sector the drive can
support
Auto
IDE Secondary Slave UDMA
*** On-Chip Serial ATA Setting ***
IDE
SATA Mode
Auto
On-Chip Serial ATA
SATA0 master
Serial ATA Port0 Mode
Seril ATA Port1 Mode
SATA1 master
Phoenix - AwardBIOS CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Controller
USB Keyboard Support
USB Mouse Support
AC97 Audio
CSA LAN (Giga-LAN)
Enabled
Disabled
Disabled
Disabled
Auto
Enable
ITEM HELP
Menu Level >>
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
RxD, TxD Active
IR Transmission Delay
UR2 Duplex Mode
Use IR Pins
Onboard Parallel Port
Parallel Por t Mode
EPP Mode Select
46
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
Hi, Lo
Enabled
Half
IR-Rx2Tx2
378/IRQ7
SPP
EPP1.7
IB850 User’s Manual
ITEM HELP
Menu Level >>
BIOS SETUP
ECP Mode Use DMA
3
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
OnChip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster. Rather
than have the BIOS issue a series of commands that transfer to or from the
disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select the
best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
On-Chip Serial ATA
The default setting of Auto allows the Serial ATA drive to be enabled,
when the system detects one.
USB Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled. In order to use USB 2.0, necessary OS drivers must be
installed first.
USB Keyboard Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
IB850 User’s Manual
47
BIOS SETUP
USB Mouse Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
AC97 Audio
The default setting of the AC97 Audio is Auto.
CSA LAN (Giga-LAN)
The default setting of the onboard Gigabit LAN is enabled.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC) installed
on the CPU card and you wish to use it. If you install an add-in FDC or the
system has no floppy drive, select Disabled in this field. This option
allows you to select the onboard FDD port.
Onboard Serial/Parallel Port
These fields allow you to select the onboard serial and parallel ports and
their addresses. The default values for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
Parallel Port
378H/IRQ7
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal. Other options include IrDA and ASKIR.
Parallel Port Mode
This field allows you to determine parallel port mode function.
SPP
Standard Printer Port
EPP
Enhanced Parallel Port
ECP
Extended Capabilities Port
48
IB850 User’s Manual
BIOS SETUP
Power Management Setup
The Power Management Setup allows you to save energy of your system
effectively.
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function
Enabled
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Modem Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
CPU THRM-Throttling
Wake-Up by PCI Card
Power On by Ring
Wake Up on LAN
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
User Define
V/H SYNC+Blank
Yes
Stop Grant
3
Disabled
Disabled
Instant-Off
50.0%
Disabled
Disabled
Disabled
Disabled
0
0:0:0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
Enabled
Enabled
Enabled
Enabled
Enabled
Enabled
ITEM HELP
Menu Level
>>
Power Supply Type
This field sets the power supply type that is in your system. By default,
the setting is set to ATX.
ACPI Function
Enable this function to support ACPI (Advance Configuration and Power
Interface).
ACPI Suspend Type
This field sets the ACPI Power Management standby state. The default
setting is S1 (POS).
IB850 User’s Manual
49
BIOS SETUP
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
User Define
Each of the ranges is from 1 min. to 1hr.
Except for HDD Power Down which
ranges from 1 min. to 15 min.
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn off
vertical and horizontal scanning.
DPMS
Allows BIOS to control the video display.
Blank Screen
Writes blanks to the video buffer.
Video Off In Suspend
When enabled, the video is off in suspend mode. The default setting is
Yes.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power supply.
The Instant Off mode allows powering off immediately upon pressing the
power button. In the Delay 4 Sec mode, the system powers off when the
power button is pressed for more than four seconds or enters the suspend
mode when pressed for less than 4 seconds.
50
IB850 User’s Manual
BIOS SETUP
CPU THRM-Throttling
When the system enters Doze mode, the CPU clock runs only part of the
time. You may select the percent of time that the clock runs.
Wake-Up by PCI Cards
Enable this field to allow wake up function through a PCI card.
Power On by Ring
This field enables or disables the power on of the system through the
modem connected to the serial port or LAN.
Wake Up On CSA Lan
Enable this field to allow wake up function through the onboard CSA
LAN.
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events which can
prevent the system from entering a power saving mode or can awaken the
system from such a mode. When an I/O device wants to gain the attention
of the operating system, it signals this by causing an IRQ to occur. When
the operating system is ready to respond to the request, it interrupts itself
and performs the service.
IB850 User’s Manual
51
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
PNP OS Install
No
Reset Configuration Data
Disabled
Menu Level
ITEM HELP
Resources Controlled By
IRQ Resources
DMA Resources
Auto (ESCD)
Press Enter
Press Enter
PCI/VGA Palette Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
Disabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Select Yes if you are
using a Plug and Play
capable operating
system Select No if you
need the BIOS to
configure non-boot
devices
>
PNP OS Install
Enable the PNP OS Install option if it is supported by the operating system
installed. The default value is No.
Reset Configuration Data
This field allows you to determine whether to reset the configuration data
or not. The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
automatically with the use of a use a PnP operating system such as
Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA cards
can work with PCI/VGA. When this field is enabled, a PCI/VGA can work
with an MPEG ISA/VESA VGA card. When this field is disabled, a
PCI/VGA cannot work with an MPEG ISA/VESA card.
52
IB850 User’s Manual
BIOS SETUP
PC Health Status
This section shows the parameters in determining the PC Health Status.
These parameters include temperatures, fan speeds and voltages.
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Warning Temperature
Current CPU Temp.
Current System Temp.
Current Chassis Temp.
CPU FAN Speed
System FAN Speed
Chassis FAN Speed
Vcore (V)
+3.3V
+5V
+12V
-12V
VBAT(V)
5VSB(V)
Shutdown Temperature
CPU Fan Failure Warning
Sys. FAN Failure Warning
Cha. FAN Failure Warning
Disabled
ITEM HELP
Menu Level >
Disabled
Disabled
Disabled
Disabled
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Temperatures/Fan Speeds/Voltages
These fields are the parameters of the hardware monitoring function
feature of the CPU card. The values are read-only values as monitored by
the system and show the PC health status.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached. This
function can help prevent damage to the system that is caused by
overheating.
Temperature/CPU/Chassis Fan Failure Warning
When enabled, t his field lets the system sounds an audible warning to the
user that the CPU fan or chassis fan has malfunctioned.
IB850 User’s Manual
53
BIOS SETUP
Frequency/Voltage Control
This section shows the user how to configure the processor frequency.
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Auto Detect DIMM/PCI Clk
Disabled
Spread Spectrum
Disabled
ITEM HELP
Menu Level
>
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only .
54
IB850 User’s Manual
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Setup Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor/User Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are prompted
to enter the password. A message will confirm the password to be
disabled. Once the password is disabled, the system will boot and you can
enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to Setup
utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
IB850 User’s Manual
55
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 98, Windows NT 4.0 and Windows 2000. The
software and drivers are included with the CPU card. If you find the items
missing, please contact the vendor where you made the purchase. The
contents of this section include the following:
Intel 875P Chipset Software Intallation Utility ................. 57
Realtek AC97 Codec Audio Driver Installation ............... 60
Intel PRO LAN Drivers Installation ............................... 61
ATI M7 VGA Driver Installation ................................... 62
ATI M9/M10 VGA Driver Installation ........................... 64
IMPORTANT NOTE:
After installing your Windows operating system (Windows
98/98SE/ME/2000/XP), you must install first the Intel Chipset Software
Installation Utility before proceeding with the drivers installation.
56
IB850 User’s Manual
DRIVERS INSTALLATION
Intel 875P Chipset Software Intallation Utility
The Intel 875P Chipset Drivers should be installed first before the
software drivers to enable Plug & Play INF support for Intel chipset
components. Follow the instructions below to complete the installation
under Windows 98/98SE/ME/2000/XP.
1. Insert the CD that comes with the CPU card and the screen below would
appear. Click Intel Chipsets and then Intel 875P Chipset Family Drivers.
2. Click Intel 875P Chipset Software Intallation Utility.
IB850 User’s Manual
57
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with the
installation process.
58
IB850 User’s Manual
DRIVERS INSTALLATION
5. On Readme Information screen, click Next to continue the installation.
6. The Setup process is now complete. Click Finish to restart the computer
and for changes to take effect. When the computer has restarted, the
system will be able to find some devices. Restart your computer when
prompted.
IB850 User’s Manual
59
DRIVERS INSTALLATION
Realtek AC97 Codec Audio Driver Installation
Follow the steps below to install the Realtek AC97 Codec Audio Drivers.
1. Insert the CD that comes with the CPU card and the screen below would
appear. Click Intel Chipsets, then Intel 875P Chipset Family Drivers. Click
Realtek AC97 Codec Audio Drivers to start installation.
2. Click Finish to restart the computer and for changes to take effect. .
60
IB850 User’s Manual
DRIVERS INSTALLATION
Intel PRO LAN Drivers Installation
The Intel PRO LAN drivers support both Intel® PRO/100 and PRO/1000
drivers. Follow the steps below to complete the installation.
1. Insert the CD that comes with the CPU card and the screen below would
appear. Click on LAN Card on the left side to make the LAN drivers
selection. Click on Intel(R) PRO LAN Drivers.
2. Click Install Now.
3. When promoted, click Restart to restart the computer and new settings
to take effect.
IB850 User’s Manual
61
DRIVERS INSTALLATION
ATI M7 VGA Driver Installation
1. Insert the CD that comes with the CPU card. On the initial screen, click
VGA Card on the left side and the screen below would appear. Click ATI
Mobility Radeon M6/M7 series VGA Driver.
2. When the Welcome screen appears, click Next to continue.
62
IB850 User’s Manual
DRIVERS INSTALLATION
3. Click Yes to accept the software license agreement and proceed with the
installation process.
4. Select on the Express icon and click Next to continue.
Remarks: The ATI M7 VGA controller is supported by the optional
MicroAGP VGA card.
IB850 User’s Manual
63
DRIVERS INSTALLATION
ATI M9/M10 VGA Driver Installation
1. Insert the CD that comes with the CPU card. On the initial screen, click
VGA Card on the left side and the screen below would appear. Click ATI
Mobility Radeon M9/M10 series VGA Driver.
2. When the Welcome screen appears, click Next to continue.
Remarks: The ATI M9 VGA controller is supported by the optional
MicroAGP VGA card.
64
IB850 User’s Manual
DRIVERS INSTALLATION
3. Click Yes to accept the software license agreement and proceed with the
installation process.
4. Click t he Express icon and click Next to continue the drivers installation
process.
5. When the “Setup Complete” window appears, Click Finish to restart the
computer and for changes to take effect.
IB850 User’s Manual
65
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement