Intel PMB-601LF User manual

Intel PMB-601LF User manual
USER’S
MANUAL
PMB-601LF
Intel® Core 2 Duo
ATX Motherboard
With VGA/Sound/2LAN
PMB-601LF M1
Copyright Notice
PMB-601LF Intel® Core 2 Duo
ATX Motherboard
With VGA/ Sound/ 2LAN
OPERATION MANUAL
COPYRIGHT NOTICE
This operation manual is meant to assist both Embedded Computer
manufacturers and end users in installing and setting up the system. The
information contained in this document is subject to change without any
notice.
This manual is copyrighted in January, 2007. You may not reproduce or
transmit in any form or by any means, electronic, or mechanical, including
photocopying and recording.
ACKNOWLEDGEMENTS
All trademarks and registered trademarks mentioned herein are the
property of their respective owners.
CE NOTICE
This is a class A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Copyright Notice
FCC NOTICE
This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
You are cautioned that any change or modifications to the equipment not
expressly approve by the party responsible for compliance could void
your authority to operate such equipment.
Contents
TABLE OF CONTENTS
CHAPTER
1-1
1-2
1-3
CHAPTER
2-1
2-2
2-3
2-4
2-5
2-6
2-7
2-8
2-9
2-10
2-11
2-12
2-13
2-14
2-15
2-16
2-17
2-18
2-19
2-20
2-21
2-22
2-23
2-24
2-25
2-26
2-27
2-28
2-29
2-30
2-31
1
INTRODUCTION
About This Manual ........................................................
System Specification ......................................................
Safety Precautions .........................................................
2
1-2
1-3
1-6
HARDWARE CONFIGURATION
Jumper & Connector Quick Reference Table ................
Component Locations ....................................................
How to Set the Jumpers .................................................
COM Port Connector ……..…………………………...
COM3 RI & Voltage Selection …………..…………….
COM4 RI & Voltage Selection ………………………
RS232/422/485(COM2) Selection ................................
Keyboard and PS/2 Mouse Connector .....................…..
Reset Connector ............................................................
Hard Disk Drive LED Connector ..................................
ATX Power Button …....................................................
External Speaker Connector ..........................................
PLED Connector ……....................................................
KeyLock Connector ..…………………………………
External SMI Connector ………………………………
Clear CMOS Data Selection …………………………
CPU Fan Connector …………………………………..
System Fan Connector …………………………………
Power Fan Connector …………………………………..
NB Fan Connector ……………………………………..
VGA Connector …………………..……………………
Serial ATA Connector …………………………………
Floppy Disk Drive Connector .......................................
Printer Connector ..........................................................
Universal Serial Bus Connector ………………………
IrDA Connector ……………………………………….
USB & LAN Connector ………………………………
ATX Power Connector ……………………………….
Sound Connector ………………………………………
CD Audio-In Connector ……………………………….
Memory Installation …………………………………..
2-2
2-3
2-4
2-6
2-8
2-9
2-10
2-11
2-11
2-12
2-12
2-12
2-13
2-13
2-13
2-14
2-14
2-15
2-15
2-15
2-16
2-17
2-19
2-20
2-21
2-22
2-23
2-25
2-26
2-27
2-27
Contents
CHAPTER
3-1
3-2
3-3
3-4
3-5
3-6
3-7
3-8
CHAPTER
4-1
4-2
4-3
4-4
4-5
4-6
4-7
4-8
4-9
4-10
4-11
4-12
4-13
4-14
4-15
3
SOFTWARE UTILITIES
Introduction …………..........................................….......
VGA Driver Utility ……………………………….……
Flash BIOS Update ..............................................….......
LAN Driver Utility …...........................................…......
Sound Driver Utility ……………………………………
Intel Chipset Software Installation Utility …..……..…..
USB2.0 Software Installation Utility …………………..
Watchdog Timer Configuration ………………………..
4
AWARD BIOS SETUP
Introduction ...................................................................
Entering Setup ...............................................................
The Standard CMOS Features ………............................
The Advanced BIOS Features .......................................
Advanced Chipset Features ...........................................
Integrated Peripherals …...............................................
Power Management Setup .............................................
PNP/PCI Configuration ….............................................
PC Health Status ……....................................................
Frequency Control ....................................…………......
Load Fail-Safe Defaults .................................................
Load Optimized Defaults .........................................….
Password Setting ………………………………………
Save & Exit Setup .........................................................
Exit Without Saving
…………………………………
APPENDIX
A
B
4-2
4-3
4-4
4-8
4-12
4-14
4-19
4-21
4-23
4-24
4-25
4-25
4-26
4-27
4-28
EXPANSION BUS
PCI Bus Pin Assignment
APPENDIX
3-2
3-3
3-4
3-6
3-7
3-8
3-9
3-10
..............................................….........
A-2
TECHNICAL SUMMARY
Block Diagram ...........................................................................
Interrupt Map ............................................................................
RTC & CMOS RAM Map ........................................................
Timer & DMA Channels Map ..................................................
I/O & Memory Map ...............................................…................
B-2
B-3
B-4
B-5
B-6
CHAPTER
INTRODUCTION
1
This chapter gives you the information for PMB-601LF. It also
outlines the System specifications.
Section includes:
z About This Manual
z System Specifications
z Safety Precautions
Experienced users can skip to chapter 2 on page 2-1
for a Quick Start.
Page:1-1
Chapter
1
Introduction
1-1. ABOUT THIS MANUAL
Thank you for purchasing our PMB-601LF Intel® Core 2 Duo ATX
Motherboard enhanced with VGA/Sound/2LAN, which is fully PC / AT
compatible. The PMB-601LF provides faster processing speed, greater
expandability and can handle more tasks than before. This manual is
designed to assist you how to install and set up the system. It contains four
chapters. The user can apply this manual for configuration according to the
following chapters:
Chapter 1 Introduction
This chapter introduces you to the background of this manual, and the
specifications for this system. The final page of this chapter will indicate
how to avoid damaging this board.
Chapter 2 Hardware Configuration
This chapter outlines the component locations and their functions. In the
end of this chapter, you will learn how to set jumper and how to configure
this card to meet your own needs.
Chapter 3 Software Utilities
This chapter contains helpful information for proper installations of the
VGA utility, LAN utility, Sound utility, and Flash BIOS Update. It also
describes the Watchdog-timer configuration.
Chapter 4 Award BIOS Setup
This chapter indicates you how to set up the BIOS configurations.
Appendix A Expansion Bus
This Appendix introduces you the expansion bus for 1 x PCI-E16 BUS, 1
x PCI-E4 BUS, 4 x PCI Bus and 1 x ISA BUS.
Appendix B Technical Summary
This section gives you the information about the Technical maps.
Page: 1-2
PMB-601LF USER′S MANUAL
Chapter
1
Introduction
1-2. SYSTEM SPECIFICATIONS
z CPU (mPGA775):
Intel® Celeron®-D, Pentium® 4, Pentium®-D, Core 2 Duo processor in
mPGA775 Socket.
2.8~3.8 GHz clock generator for Pentium 4
1.86~2.66GHz clock generator for Core 2 Duo
Front Side Bus 533/667/800/1066 MHZ.
Auto detect voltage regulator.
z CHIPSET :
Intel Q965 + ICH8DO+FWH
z MEMORY :
Supports up to 8GB DDR SDRAM.
Four 240-pin DDR2 DIMM sockets on board.
z CACHE :
Built-in CPU.
z REAL-TIME CLOCK :
Build in South Bridge.
z BIOS :
Phoenix-AwardBIOS™ for plug & play function.
8Mb with VGA BIOS.
Easy update 1MB flash EEPROM.
Support S/IO Setup.
z KEYBOARD CONNECTOR :
Mini DIN connector.
Supports for AT/PS2 keyboard.
z MOUSE CONNECTOR :
Mini DIN connector.
Supports for PS/2 Mouse.
z BUS SUPPORT :
1 PCI-E16 Slot, support Graphic Card
1 PCI-E4 Slots, support I/O card
4 PCI Slots
PMB-601LF USER′S MANUAL
Page: 1-3
Chapter
1
Introduction
1 ISA Slot
z DISPLAY :
Built-in Intel Q965, support for CRT.
Onboard 15-pin VGA D-SUB connector, support for resolution on SVGA
Monitor.
z SATA INTERFACE :
6 SATA ports, support RAID 0,1,5,10.
z SERIAL PORT :
Four serial connectors.
COM1/3/4 for RS-232, COM2 for RS-232/422/485.
COM3/4 can output +5V or +12V, and use jumper settings.
z FLOPPY DISK DRIVER INTERFACE :
Support up to two Floppy Disk Drives, 3.5" and 5.25" (360K / 720K / 1.2M /
1.44M / 2.88M).
z USB CONNECTOR :
Support up to ten USB 2.0 ports.
4 ports with LAN1/ LAN2 on rear panel.
6 ports with external 2.54 connector 2x5-pin headpin.
z LAN ADAPTER :
Dual ports, Intel® 82573V x 2, 10/100/1000 BaseT Ethernet.
LAN1: 10/100/1000 BaseT Ethernet
LAN2: 10/100/1000 BaseT Ethernet
Support wake-on-LAN function.
z SOUND :
Realtek ALC262A (HD Codec), including SPDIF.
Fully Compliant HD Analog I/O Component
16-Bit Stereo Full-Duplex Codec
Four Analog Line-level Stereo Inputs for Connection.
High Quality CD Input with Ground Sense
Stereo Line-Level Output
Interface: Line-In, Line-Out, Microphone, and CD Audio-In.
Page: 1-4
PMB-601LF USER′S MANUAL
Chapter
1
Introduction
z HARDWARE MONITORING FUNCTION :
Monitor Voltage, CPU temperature, & Cooling fan.
If CPU Temperature is over setting, the buzzer will send out a warming (only
under DOS system).
z IRDA PORT :
5-pin Infrared port, support IrDA v1.0 SIR protocol
z PARALLEL PORT :
SPP / ECP / EPP Function.
1 port, bi-directional parallel port.
z GREEN FUNCTION :
Controlled by hardware and software.
z LED INDICATOR :
System power
Hard Disk access (SATA)
z DMA CONTROLLER :
82C37 x 2
z DMA CHANNELS :
7
z INTERRUPT CONTROLLERS :
82C59 x 2
z INTERRUPT LEVELS :
15
z OPERATING TEMPERATURE :
0 to 60°C.
z BOARD DIMENSIONS :
305mm x 344mm, 12” x9.61”
z BOARD NET WEIGHT :
810 gram.
PMB-601LF USER′S MANUAL
Page: 1-5
Chapter
1
Introduction
1-3. SAFETY PRECAUTIONS
Follow the messages below to avoid your systems from damage:
1. Keep your system away from static electricity on all occasions.
2. Prevent electric shock. Don‘t touch any components of this card when the
card is power-on. Always disconnect power when the system is not in use.
3. Disconnect power when you change any hardware devices. For instance,
when you connect a jumper or install any cards, a surge of power may
damage the electronic components or the whole system.
Page: 1-6
PMB-601LF USER′S MANUAL
HARDWARE
CONFIGURATION
CHAPTER
2
** QUICK START **
Helpful information describes the jumper & connector settings, and
component locations.
Section includes:
z Jumper & Connector Quick Reference Table
z Component Locations
z Configuration and Jumper settings
z Connector’s Pin Assignments
Page 2-1
Chapter
2
Hardware Configuration
2-1. JUMPER & CONNECTOR QUICK REFERENCE TABLE
COM Port Connector
....................…..................………
…………………………………..
COM3 Port RI/Voltage Selection ……………………..
COM4 Port RI/Voltage Selection ……………………
RS232/422/485 (COM2) Selection .....................………
Keyboard/Mouse Connector ..........….....………………
Reset Connector .........................…....................……….
Hard Disk Drive LED Connector .......................……….
ATX Power Button ……………………………………..
External Speaker Connector ....…........................………
PLED Connector …………….…….…...............………
KeyLock Connector ……………………………………
External SMI Connector ……………..…………..…….
Clear CMOS Data Selection ……………………………
CPU Fan Connector ……………………………………
System Fan Connector ………………………………….
Power Fan Connector …………………………………..
NB Fan Connector ……………………………………..
VGA Connector ………………………………………..
Serial ATA Connector ………………………………….
Floppy Disk Drive Connector ……..........………....…...
Printer Connector …….....................……………......…
Universal Serial Bus Connector …….....................……
IrDA Connector ………………………………………..
USB&LAN Connector …....................................………
ATX Power Connector …………………………………
Sound Connector ………………………….……………
CD Audio-In Connector ………………………………..
Memory Installation ..................................…......………
……………………………………
Page: 2-2
COM1, COM2
COM3, COM4
JP6
JP7
JP5
KB_MS1
JP8 (5, 7)
JP8 (1, 3)
JP8 (6, 8)
JP8 (14, 16, 18, 20)
JP8 (2, 4)
JP8 (13, 15)
JP8 (17, 19)
JP4
CPU_FAN1
SYS_FAN1
PWR_FAN1
NB_FAN1
VGA1
SATA1, SATA2, SATA3, SATA4
FDD1
LPT1
USB1, USB2, USB3
JP1
USB_RJG1, USB_RJG2
ATX_PWR1, ATX_PWR2
JAUDIO1
CD_IN1
DIMM1, DIMM2, DIMM3,
DIMM4
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-2. COMPONENT LOCATIONS
PMB-601LF Connector, Jumper and Component locations
PMB-601LF USER′S MANUAL
Page: 2-3
Chapter
2
Hardware Configuration
2-3. HOW TO SET THE JUMPERS
You can configure your board by setting jumpers. Jumper is consists of
two or three metal pins with a plastic base mounted on the card, and by
using a small plastic "cap", Also known as the jumper cap (with a metal
contact inside), you are able to connect the pins. So you can set-up your
hardware configuration by "open" or "close" pins.
The jumper can be combined into sets that called jumper blocks. When
the jumpers are all in the block, you have to put them together to set up
the hardware configuration. The figure below shows how this looks like.
JUMPERS AND CAPS
If a jumper has three pins (for examples, labelled PIN1, PIN2, and PIN3),
You can connect PIN1 & PIN2 to create one setting by shorting. You can
either connect PIN2 & PIN3 to create another setting. The same jumper
diagrams are applied all through this manual. The figure below shows
what the manual diagrams look and what they represent.
Page: 2-4
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
JUMPER DIAGRAMS
Jumper Cap
looks like this
2 pin Jumper
looks like this
3 pin Jumper
looks like this
Jumper Block
looks like this
JUMPER SETTINGS
2 pin Jumper close(enabled)
Looks like this
1
1
3 pin Jumper
2-3 pin close(enabled)
Looks like this
1
1
Jumper Block
1-2 pin close(enabled)
Looks like this
1 2
PMB-601LF USER′S MANUAL
1
2
Page: 2-5
Chapter
2
Hardware Configuration
2-4. COM PORT CONNECTOR
COM1 : COM1 Connector
COM1 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
ASSIGNMENT
COM1_DCD#
COM1_RX
COM1_TX
COM1_DTR#
GND
COM1_DSR#
COM1_RTS#
COM1_CTS#
COM1_RI#
COM2 : COM2 Connector
The COM2 is selectable as RS-232/422/485.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
Page: 2-6
ASSIGNMENT
RS-232
RS-422
RS-485
COM2_DCD#
TXTXCOM2_RX
TX+
TX+
COM2_TX
RX+
RX+
COM2_DTR#
RXRXGND
GND
GND
COM2_DSR#
RTSGND
COM2_RTS#
RTS+
GND
COM2_CTS#
CTS+
GND
COM2_RI#
CTSGND
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
COM3 : COM3 Connector
COM3 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
ASSIGNMENT
COM3_DCD#
COM3_RX
COM3_TX
COM3_DTR#
GND
COM3_DSR#
COM3_RTS#
COM3_CTS#
COM3_RI#
COM4 : COM4 Connector
COM4 is fixed as RS-232.
The pin assignment is as follows :
PIN
1
2
3
4
5
6
7
8
9
ASSIGNMENT
COM4_DCD#
COM4_RX
COM4_TX
COM4_DTR#
GND
COM4_DSR#
COM4_RTS#
COM4_CTS#
COM4_RI#
PMB-601LF USER′S MANUAL
Page: 2-7
Chapter
2
Hardware Configuration
2-5. COM3 RI & VOLTAGE SELECTION
JP6 : COM3 RI & Voltage Selection
The selections are as follows:
SELECTION
JUMPER
SETTINGS
5V
5-6
12V
3-4
RI
1-2
JUMPER
ILLUSTRATION
***Manufacturing Default -- RI.
Page: 2-8
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-6. COM4 RI & VOLTAGE SELECTION
JP7 : COM4 RI & Voltage Selection
The selections are as follows:
SELECTION
JUMPER
SETTINGS
5V
5-6
12V
3-4
RI
1-2
JUMPER
ILLUSTRATION
***Manufacturing Default -- RI.
PMB-601LF USER′S MANUAL
Page: 2-9
Chapter
2
Hardware Configuration
2-7. RS232/422/485 (COM2) SELECTION
JP5 : RS-232/422/485 (COM2) Selection
This connector is used to set the COM2 function.
The jumper settings are as follows :
COM 2
Function
Jumper Settings
(pin closed)
RS-232
All Open
RS-422
1-2, 3-4, 9-10
RS-485
1-2, 5-6, 7-8
Jumper
Illustrations
*** Manufacturing default -- RS-232.
Page: 2-10
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-8. KEYBOARD AND PS/2 MOUSE CONNECTOR
KB_MS1 : Keyboard and PS/2 Mouse Connector
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
ASSIGNMENT
KBDATA
NC
GND
VCC5
KBCLK
NC
MSDATA
NC
GND
VCC5
MSCLK
NC
2-9. RESET CONNECTOR
JP8 (5, 7) : Reset Connector.
The pin assignment is as follows :
PIN
5
7
ASSIGNMENT
GND
RST_BTN
PMB-601LF USER′S MANUAL
Page: 2-11
Chapter
2
Hardware Configuration
2-10. HARD DISK DRIVE LED CONNECTOR
JP8 (1, 3) : Hard Disk Drive LED Connector
The pin assignment is as follows :
PIN
1
3
ASSIGNMENT
HD_LED+
HD_LED-
2-11. ATX POWER BUTTON
JP8 (6, 8) : ATX Power Button
The pin assignment is as follows :
PIN
6
8
ASSIGNMENT
PWRBTNSW
GND
2-12. EXTERNAL SPEAKER CONNECTOR
JP8 (14, 16, 18, 20) : External Speaker Connector
The pin assignment is as follows :
PIN
14
16
18
20
Page: 2-12
ASSIGNMENT
SPK_VCC
SPEAKER SIGNAL
SPEAKER SIGNAL
SPEAKER SIGNAL
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-13. PLED CONNECTOR
JP8 (2, 4) : PLED Connector
The pin assignment is as follows:
PIN
2
4
ASSIGNMENT
PW_LED+
PW_LED-
2-14. KEYLOCK CONNECTOR
JP8 (13, 15) : Keylock Connector
The pin assignment is as follows:
PIN
13
15
ASSIGNMENT
KEYLOCK
GND
2-15. EXTERNAL SMI CONNECTOR
JP8 (17,19) : External SMI Connector
The pin assignment is as follows:
PIN
17
19
ASSIGNMENT
SLP_BTN
GND
PMB-601LF USER′S MANUAL
Page: 2-13
Chapter
2
Hardware Configuration
2-16. CLEAR CMOS DATA SELECTION
JP4 : Clear CMOS Data Selection
The selections are as follows :
FUNCTION
JUMPER SETTING
(pin closed)
Normal
1-2
Clear CMOS
2-3
JUMPER
ILLUSTRATION
*** Manufacturing Default -- Normal.
Note: To clear CMOS data, user must power-off the computer and set the jumper
to “Clear CMOS” as illustrated above. After five to six seconds, set the
jumper back to “Normal” and power-on the computer.
2-17. CPU FAN CONNECTOR
CPU_FAN1 : CPU Fan connector
The pin assignment is as follows:
PIN
1
2
3
4
Page: 2-14
ASSIGNMENT
GND
VCC12
LPC1_FANIO1
LPC1_FANPWM1
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-18. SYSTEM FAN CONNECTOR
SYS_FAN1 : System Fan connector
The pin assignment is as follows:
PIN
1
2
3
ASSIGNMENT
GND
VCC12
LPC1_FANIO2
2-19. POWER FAN CONNECTOR
PWR_FAN1 : Power Fan connector
The pin assignment is as follows:
PIN
1
2
3
ASSIGNMENT
GND
VCC12
LPC1_FANIO3
2-20. NB FAN CONNECTOR
NB_FAN1 : North Bridge Fan connector
The pin assignment is as follows:
PIN
1
2
ASSIGNMENT
GND
VCC12
PMB-601LF USER′S MANUAL
Page: 2-15
Chapter
2
Hardware Configuration
2-21. VGA CONNECTOR
VGA1: VGA Connector
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Page: 2-16
ASSIGNMENT
RED
GREEN
BLUE
NC
GND
GND
GND
GND
VCC
GND
NC
DATA
HSYNC
VSYNC
CLK
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-22. SERIAL ATA CONNECTOR
SATA1~SATA4: The PMB-601LF possesses four Serial ATA
Connector, SATA1~SATA4. The pin assignments are as follows:
SATA1:
PIN
1
2
3
4
5
6
7
ASSIGNMENT
GND
SATA_TXPC4
SATA_TXNC4
GND
SATA_RXNC4
SATA_RXPC4
GND
SATA2:
PIN
1
2
3
4
5
6
7
ASSIGNMENT
GND
SATA_TXPC5
SATA_TXNC5
GND
SATA_RXNC5
SATA_RXPC5
GND
PMB-601LF USER′S MANUAL
Page: 2-17
Chapter
2
Hardware Configuration
SATA3:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ASSIGNMENT
GND
SATA_TXPC0
SATA_TXNC0
GND
SATA_RXNC0
SATA_RXPC0
GND
GND
SATA_TXPC1
SATA_TXNC1
GND
SATA_RXNC1
SATA_RXPC1
GND
SATA4:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
ASSIGNMENT
GND
SATA_TXPC2
SATA_TXNC2
GND
SATA_RXNC2
SATA_RXPC2
GND
GND
SATA_TXPC3
SATA-TXNC3
GND
SATA_RXNC3
SATA_RXPC3
GND
Page: 2-18
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-23. FLOPPY DISK DRIVE CONNECTOR
FDD1 : Floppy Disk Drive Connector
You can use a 34-pin daisy-chain cable to connect two-FDDs. On one
end of this cable is a 34-pin flat cable to attach the FDD on the board,
and the other side is attaches two FDDs.
The pin assignments are as follows :
PIN
1
3
5
7
9
11
13
15
17
19
21
23
25
27
29
31
33
ASSIGNMENT
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
PMB-601LF USER′S MANUAL
PIN
2
4
6
8
10
12
14
16
18
20
22
24
26
28
30
32
34
ASSIGNMENT
F_DENSEL#
NC
NC
F_INDEX#
F_MTRA#
F_DRVB#
F_DRVA#
F_MTRB#
F_DIR#
F_STEP#
F_WDATA#
F_WGATE#
F_TRK0#
F_WPT#
F_RDATA#
F_HDSEL#
F_DSKCHG#
Page: 2-19
Chapter
2
Hardware Configuration
2-24. PRINTER CONNECTOR
LPT1: Printer Connector
As to link the Printer to the card, you need a cable to connect both
DB25 connector and parallel port.
The pin assignments are as follows :
PIN
1
2
3
4
5
6
7
8
9
10
11
12
13
Page: 2-20
ASSIGNMENT
STB
PDR0
PDR1
PDR2
PDR3
PDR4
PDR5
PDR6
PDR7
ACK#
BUSY
PE
SLCT
PIN
14
15
16
17
18
19
20
21
22
23
24
25
26
ASSIGNMENT
AFD#
ERR#
INIT#
SLIN#
GND
GND
GND
GND
GND
GND
GND
GND
NC
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-25. UNIVERSAL SERIAL BUS CONNECTOR
USB1: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
USB4_VCC5
USBN8
USBP8
GND
NC
USB4_VCC5
USBN9
USBP9
GND
NC
USB2: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
USB3_VCC5
USBN6
USBP6
GND
NC
USB3_VCC5
USBN7
USBP7
GND
NC
PMB-601LF USER′S MANUAL
Page: 2-21
Chapter
2
Hardware Configuration
USB3: Universal Serial Bus Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
ASSIGNMENT
USB2_VCC5
USBN4
USBP4
GND
NC
USB2_VCC5
USBN5
USBP5
GND
NC
2-26. IRDA CONNECTOR
JP1: IrDA (Infrared) Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
Page: 2-22
ASSIGNMENT
VCC5
NC
IRRX
GND
IRTX
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-27. USB&LAN CONNECTOR
USB_RJG2: USB & LAN Connector
The pin assignments are as follows:
LAN:
PIN
1
2
3
4
11
12
13
14
USB:
PIN
A1
A2
A3
A4
B1
B2
B3
B4
ASSIGNMENT
LAN1_TXDP
LAN1_TXDN
LAN1_RXDP
LAN1_RXDN
LAN1_LILED
LAN1_ACTLED
LAN1_SPD100
LAN1_LEDVCC
ASSIGNMENT
USB0_VCC5
USBN0
USBP0
GND
USB0_VCC5
USBN1
USBP1
GND
PMB-601LF USER′S MANUAL
Page: 2-23
Chapter
2
Hardware Configuration
USB_RJG1: USB & LAN Connector
The pin assignments are as follows:
LAN:
PIN
1
2
3
4
5
6
7
8
11
12
13
14
USB:
PIN
A1
A2
A3
A4
B1
B2
B3
B4
Page: 2-24
ASSIGNMENT
LAN2_1MDI_P0
LAN2_1MDI_N0
LAN2_1MDI_P1
LAN2_1MDI_N1
LAN2_1MDI_P2
LAN2_1MDI_N2
LAN2_1MDI_P3
LAN2_1MDI_N3
LAN2_LILED
LAN2_ACTLED
LAN2_SPD100
LAN2_SPD1000
ASSIGNMENT
USB1_VCC5
USBN2
USBP2
GND
USB1_VCC5
USBN3
USBP3
GND
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-28. ATX POWER CONNECTOR
ATX_PW1 : ATX 12V Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
GND
GND
+12V
+12V
ATX_PW2 : ATX Power Connector
The pin assignments are as follows:
PIN
1
2
3
4
5
6
7
8
9
10
11
12
ASSIGNMENT
+3.3V
+3.3V
GND
+5V
GND
+5V
GND
POK
5VSB
+12V
+12V
+3.3V
PMB-601LF USER′S MANUAL
PIN
13
14
15
16
17
18
19
20
21
22
23
24
ASSIGNMENT
+3.3V
-12V
GND
PSON
GND
GND
GND
-5V
+5V
+5V
+5V
GND
Page: 2-25
Chapter
2
Hardware Configuration
2-29. SOUND CONNECTOR
JAUDIO1 : Sound Connector, including Line-In, Line-Out & Mic.
Also can support only MIC connector. The pin assignments are as
follows :
Line-In
PIN ASSIGNMENT
32
HD_LINE-L
33
GND
34
GND
35
HD_LINE-R
Line-Out
PIN ASSIGNMENT
22
HD_OUT-L
23
NC
24
NC
25
HD_OUT-R
Mic-In
PIN
1
2
3
4
5
Page: 2-26
ASSIGNMENT
GND
HD_MIC1
HD_MIC_GND
NC
HD_MIC_VCC
PMB-601LF USER′S MANUAL
Chapter
2
Hardware Configuration
2-30. CD AUDIO-IN CONNECTOR
CD_IN1 : CD Audio-In Connector
The pin assignments are as follows:
PIN
1
2
3
4
ASSIGNMENT
CD-L
CD-REF
CD-REF
CD-R
2-31. MEMORY INSTALLATION
PMB-601LF CPU Card can support up to 4GB in four DIMM sockets.
DRAM BANK CONFIGURATION
DIMM 1
128MB
256MB
512MB
1GB
2GB
DIMM 2
128MB
256MB
512MB
1GB
2GB
PMB-601LF USER′S MANUAL
DIMM3
128MB
256MB
512MB
1GB
2GB
DIMM4
128MB
256MB
512MB
1GB
2GB
TOTAL MEMORY
512MB
1GB
2GB
4GB
8GB
Page: 2-27
SOFTWARE
UTILITIES
CHAPTER
3
This chapter comprises the detailed information of VGA driver, LAN
driver, Sound driver, and flash BIOS update. It also describes on how to
configuration the watchdog timer.
Section includes:
z Introduction.
z VGA Driver Utility
z Flash BIOS Update
z LAN Driver Utility
z Sound Driver Utility
z Intel® Chipset Software Installation Utility
z USB2.0 Chipset Software Installation Utility
z Watchdog Timer Configuration
Page: 3-1
Chapter
3
Software Configuration
3-1. INTRODUCTION
Enclosed with our PMB-601LF package is our driver utility, which may
comes in a form of a CD ROM disc or floppy diskettes. For CD ROM disc
user, you will only need some of the files contained in the CD ROM disc,
please kindly refer to the following chart:
Filename
(Assume that CD ROM drive is D:)
D:\Driver\VGA
Purpose
Intel Q965
For VGA driver installation
D:\Driver\FLASH
For BIOS update utility
D:\Driver\LAN
For LAN Driver installation
D:\Driver\Sound
Realtek ALC262A Audio HD
For Sound driver installation
D:\Driver\UTILITY
Intel® Chipset Software
Installation Utility
For Win 2000, XP,2003
D:\Driver\RAID
Intel® ICH8-R RAID Software
Installation Utility For Win 2000,
XP,2003
D:\Driver\USB 2.0
USB 2.0 Software Installation
Utility
For Win 2000, XP
D:\Driver\F6flpy32
Intel® ICH8-R driver used for
FLOPPY when Install Win2000,
XP,2003
User should remember to install the Utility right after the OS fully installed.
Page:3-2
PMB-601LF USER′S MANUAL
Chapter
3
Software Configuration
3-2. VGA DRIVER UTILITY
The VGA interface embedded with our PMB-601LF can support a wide
range of display. You can display CRT, PCI-E (SDVO) simultaneously
with the same mode.
3-2-1. Installation of VGA Driver:
To install the VGA Driver, simply follow the following steps:
1.
2.
3.
4.
5.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 2000/XP/2003 system, go to the directory where
VGA driver is located.
Click Setup.exe file for VGA driver installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
PMB-601LF USER′S MANUAL
Page:3-3
Chapter
3
Software Configuration
3-3. FLASH BIOS UPDATE
3-3-1. System BIOS Update:
Users of PMB-601LF can use the program “Awdflash.exe” contained in CD
ROM for BIOS update.
This is found in D:\flash\Awdflash.exe.
3-3-2. To update BIOS :
(1) Install “Awdflash.exe” from the CD ROM Disk into your system.
(2) Insert the new BIOS file you have obtained from Protech.
(3) Type the pathname to Awdflash.exe and execute the BIOS update with
file B601xxxx.bin
C:\UTIL\AWDFLASH\AWARDFLASH
B601xxxx.bin
(4) The screen will display the table below:
AwardBIOS Flash Utility V8.69
( C )Phoenix Technologies Ltd. All Rights Reserved
For Broadwater-6A79LP69C-00
DATE : 01/16/2007
Flash Type - SST 49LF008A /3.3V
File Name to Program : B601xxxx.bin
Message :
Page:3-4
Do You Want To Save BIOS (Y/N)
PMB-601LF USER′S MANUAL
Chapter
3
Software Configuration
If you want to save up the original BIOS, enter “Y ”and press <
Enter > . If you choose “N”, the following table will appear on
screen.
AwardBIOS Flash Utility V8.69
( C )Phoenix Technologies Ltd. All Rights Reserved
For Broadwater-6A79LP69C-00
DATE : 01/16/2007
Flash Type - SST 49LF008A /3.3V
File Name to Program : B601xxxx.bin
Message :
Press ‘Y’ to Program or ‘N’ to Exit
Select “Y”, and the BIOS will be renewed. When you are refreshing your BIOS, do not turn off or
reset the system, or you will damage the BIOS. After you have completed all the programming, you
will see the line: “Reset System or power off to accomplish update process!”. Please turn off or reset
the system. Then the Flash BIOS is fully implemented.
PMB-601LF USER′S MANUAL
Page:3-5
Chapter
3
Software Configuration
3-4. LAN DRIVER UTILITY
3-4-1. Introduction
PMB-601LF is enhanced with LAN function that can support various
network adapters. Installation programs for LAN drivers are listed as
follows:
For more details on Installation procedure, please refer to Readme.txt
file found on LAN DRIVER UTILITY.
Page:3-6
PMB-601LF USER′S MANUAL
Chapter
3
Software Configuration
3-5. SOUND DRIVER UTILITY
3-5-1. Introduction
The Realtek ALC262A sound function enhanced in this system is fully
compatible with Windows 2000 and Windows XP. Below, you will find
the content of the Sound driver :
3-5-2. Installation Procedure for Windows 2000/XP/2003
1.
2.
3.
4.
5.
From the task bar, click on Start, and then Run.
In the Run dialog box, type D:\Sound\path\setup, where
“D:\Sound\pathname” refers to the full path to the source files.
Click on the OK button or press the ENTER key.
Click on the “Next” and OK prompts as they appear.
Reboot the system to complete the driver installation.
PMB-601LF USER′S MANUAL
Page:3-7
Chapter
3
Software Configuration
3-6. INTEL® CHIPSET SOFTWARE INSTALLATION UTILITY
3-6-1. Introduction
The Intel® Chipset Software Installation Utility installs to the target
system the Windows* INF files that outline to the operating system how
the chipset components will be configured. This is needed for the
proper functioning of the following features:
-
Core PCI and ISAPNP Services
AGP Support
IDE/ATA33/ATA66/ATA100 Storage Support
USB Support
Identification of Intel® Chipset Components in Device Manager
3-6-2. Installation of Utility for Windows 2000/XP/2003
The Utility Pack is to be installed only for Windows 2000 and XP
program.
It should be installed right after the OS installation, kindly follow the
following steps:
1.
2.
3.
4.
5.
Page:3-8
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 2000/XP/2003 system, go to the directory where
Utility Disc is located.
Click Setup.exe file for utility installation.
Follow the instructions on the screen to complete the installation.
Once installation is completed, shut down the system and restart in
order for the changes to take effect.
PMB-601LF USER′S MANUAL
Chapter
3
Software Configuration
3-7. USB2.0 SOFTWARE INSTALLATION UTILITY
3-7-1. Installation of Utility for Windows 2000/XP
Intel USB 2.0 Enhanced Host Controller driver can only be used on
Windows 2000 and Windows XP on Intel Desktop boards. It should be
installed right after the OS installation, kindly follow the following steps:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Place insert the Utility Disk into Floppy Disk Drive A/B or CD
ROM drive.
Under Windows 2000, and XP system, go to the directory where
Utility Disc is located.
Start the “System” wizard in control panel. (Click
Start/Settings/Control Panel).
Select “Hardware” and click “Device Manager ” button.
Double Click “USB Root Hub”.
Select “Driver”.
Click “Install” to install the driver.
Follow the instructions on the screen to complete the installation.
Click “Finish” after the driver installation is complete.
PMB-601LF USER′S MANUAL
Page:3-9
Chapter
3
Software Configuration
3-8. WATCHDOG TIMER CONFIGURATION
The I/O port address of the watchdog timer is 2E(hex) and 2F(hex). 2E (hex)
is the address port. 2F(hex) is the data port. User must first assign the
address of register by writing address value into address port 2E(hex), then
write/read data to/from the assigned register through data port 2F (hex).
Configuration Sequence
There are three steps to completing the configuration setup:
(1) Enter the MB PnP Mode.
(2) Modify the data of configuration registers.
(3) Exit the MB PnP Mode.
Undesired result may occur if the MB PnP Mode is not exited normally.
(1) Enter the MB PnP Mode
To enter the MB PnP Mode, four special I/O write operations are to be
performed.
(2) Modify the data of configuration registers
All configuration registers can be accessed after entering the MB PnP Mode.
Before accessing a selected register, the content of index 07h must be
changed to the LDN to which the register belongs, except some Global
registers.
(3) Exit the MB PnP Mode
Set bit 1 of the configure control register (index=02h) to “1” to exit the MB
PnP Mode.
Sample code:
;***********************************************;
;Enter PnP Mode
;***********************************************;
MOVDX,2Eh
MOVAL,87h
OUTDX,AL
MOVAL,01h
OUTDX,AL
MOVAL,55h
OUTDX,AL
MOVAL,55h
OUTDX,AL
;***********************************************;
;Select LDN to 07h
;***********************************************;
MOVDX,2Eh
Page:3-10
PMB-601LF USER′S MANUAL
Chapter
3
Software Configuration
MOVAL,07h
OUTDX,AL
MOVDX,2Fh
MOVAL,07h
OUTDX,AL
;***********************************************;
;Select Time resolution by index 72h
;AL=C0h Second resolution
;AL=80h Minute resolution
;***********************************************;
MOVDX,2Eh
MOVAL,72h
OUTDX,AL
MOVDX,2Fh
MOVAL,0C0h
OUTDX,AL
;***********************************************;
;Write non-zero value into index 73h
;for Enable WDT and Start count down.
;***********************************************;
MOVDX,2Eh
MOVAL,73h
OUTDX,AL
MOVDX,2Fh
MOVAL,02h
OUTDX,AL
;***********************************************;
;Write zero value into register AL
;for Disable WDT.
;***********************************************;
MOVDX,2Eh
MOVAL,73h
OUTDX,AL
MOVDX,2Fh
MOVAL,00h
OUTDX,AL
;***********************************************;
;Exit PnP Mode
;***********************************************;
MOVDX,2Eh
MOVAL,02h
OUTDX,AL
MOVDX,2Fh
MOVAL,02h
OUTDX,AL
PMB-601LF USER′S MANUAL
Page:3-11
CHAPTER
AWARD
BIOS SETUP
4
This chapter shows how to set up the Award BIOS.
Section includes:
z Introduction
z Entering Setup
z The Standard CMOS Features
z The Advanced BIOS Features
z The Advanced Chipset Features
z Integrated Peripherals
z Power Management Setup
z PNP/PCI Configuration
z PC Health Status
z Frequency Control
z Load Fail-Safe Defaults
z Load Optimized Defaults
z Password Setting
z Save and Exit Setup
z Exit Without Saving
Page: 4-1
Chapter
4
Award BIOS Setup
4-1. INTRODUCTION
This chapter will show you the function of the BIOS in managing the
features of your system. The PMB-601LF Intel Core 2 Duo ATX
Motherboard is equipped with the BIOS for system chipset from Phoenix Award Software Inc. This page briefly explains the function of the BIOS in
managing the special features of your system. The following pages describe
how to use the BIOS for system chipset Setup menu.
Your application programs (such as word processing, spreadsheets, and
games) rely on an operating system such as DOS or OS/2 to manage such
things as keyboard, monitor, disk drives, and memory.
The operating system relies on the BIOS (Basic Input and Output system), a
program stored on a ROM (Read-only Memory) chip, to initialize and
configure your computer's hardware. As the interface between the hardware
and the operating system, the BIOS enables you to make basic changes to
your system's hardware without having to write a new operating system.
The following diagram illustrates the interlocking relationships between the
system hardware, BIOS, operating system, and application program:
Page: 4-2
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-2. ENTERING SETUP
When the system is powered on, the BIOS will enter the Power-On Self
Test (POST) routines and the following message will appear on the lower
screen:
PRESS <DEL> TO ENTER SETUP, ESC TO SKIP MEMORY TEST
As long as this message is present on the screen you may press the <Del>
key (the one that shares the decimal point at the bottom of the number
keypad) to access the Setup program. In a moment, the main menu of the
Award SETUP program will appear on the screen:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
►Frequency Control
►Advanced BIOS Features
Load Fail-Safe Defaults
►Advanced Chipset Features
Load Optimized Defaults
►Integrated Peripherals
Set Supervisor Password
►Power Management Setup
Set User Password
►PnP/PCI Configurations
Save & Exit Setup
►PC Health Status
Exit Without Saving
Esc : Quit
F10 : Save & Exit Setup
↑↓→← : Select Item
Time, Date, Hard Disk Type .…
Setup program initial screen
You may use the cursor the up/down keys to highlight the individual menu
items. As you highlight each item, a brief description of the highlighted
selection will appear at the bottom of the screen.
PMB-601LF USER′S MANUAL
Page: 4-3
Chapter
4
Award BIOS Setup
4-3. THE STANDARD CMOS FEATURES
Highlight the〝STANDARD CMOS FEATURES〞and press the <ENTER>
key and the screen will display the following table:
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
▶
▶
▶
▶
▶
▶
Date (mm:dd:yy)
Time (hh:mm:ss)
Thu, Jun 22 2007
13 : 54 : 47
SATA Channel 1
SATA Channel 2
SATA Channel 3
SATA Channel 4
SATA Channel 5
SATA Channel 6
[ HDS728080PLA380]
[ None]
[ None]
[ None]
[ None]
[ None]
Drive A
[1.44M, 3.5 in.]
Video
Halt On
[EGA/VGA]
[All, But Keyboard]
Item Help
Menu Level
Base Memory
Extended Memory
Total Memory
►
Change the day,
month, year and
century
640K
514048K
515072K
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
CMOS Setup screen
In the above Setup Menu, use the arrow keys to highlight the item and then use
the <PgUp> or <PgDn> keys to select the value you want in each item.
DATE:
< Month >, < Date > and <Year >. Ranges for each value are in the CMOS
Setup Screen, and the week-day will skip automatically.
TIME:
< Hour >, < Minute >, and < Second >. Use 24 hour clock format, i.e., for PM
numbers, add 12 to the hour. For example: 4: 30 P.M. You should enter the
time as 16:30:00.
Page: 4-4
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
SATA CHANNEL 0/1/2/3/4/5:
The BIOS can automatically detect the specifications and optimal operating
mode of almost all SATA hard drives. When you select type AUTO for a
hard drive, the BIOS detect its specifications during POST, every time system
boots.
If you do not want to select drive type AUTO, other methods of selecting
drive type are available:
1.
Match the specifications of your installed SATA hard drive(s) with
the preprogrammed values for hard drive types 1 through 45.
2.
Select USER and enter values into each drive parameter field.
3.
Use the SATA HDD AUTO DETECTION function in Setup.
Here is a brief explanation of drive specifications:
Type: The BIOS contains a table of pre-defined drive types. Each
defined drive type has a specified number of cylinders, number of heads,
write precompensation factor, landing zone, and number of sectors.
Drives whose specifications do not accommodate any predefine type are
classified as type USER.
•
Size: Disk drive capacity (approximate). Note that this size is usually
greater than the size of a formatted disk given by a disk-checking
program.
•
Cyls: number of cylinders.
•
Head: number of heads.
•
Precomp: write precompensation cylinders.
•
Landz: landing zone.
•
Sector: number of sectors.
•
Mode: Auto, Normal, Large or LBA.
Auto: The BIOS automatically determines the optimal mode.
ƒ
Normal: Maximum number of cylinders, heads, sectors
supported are 1024, 16 and 63.
ƒ
Large: For drives that do not support LBA and have more
than 1024 cylinders.
ƒ
LBA (Logical Block Addressing): During drive accesses, the
PMB-601LF USER′S MANUAL
Page: 4-5
Chapter
4
Award BIOS Setup
SATA controller transforms the data address described by
sector, head and cylinder number into a physical block
address, significantly improving data transfer rates. For
drives greater than 1024 cylinders.
DRIVE A:
Select the type of floppy disk drive installed in your system. The available
options are 360KB 5.25in, 1.2KB 5.25in, 720KB 3.5in, 1.44MB 3.5in,
2.88MB 3.5in and None.
VIDEO:
This category selects the type of video adapter used for the primary system
monitor. Although secondary monitors are supported, you do not have to
select the type in Setup. Available Options are as follows:
EGA/VGA
Enhanced Graphics Adapter/Video Graphics Array.
For EGA, VGA, SEGA, SVGA or PGA monitor
adapters.
CGA 40
Color Graphics Adapter, power up in 40 column mode.
CGA 80
Color Graphics Adapter, power up in 80 column mode.
MONO
Monochrome adapter, includes high resolution
monochrome adapters.
HALT ON:
This category allows user to choose whether the computer will stop if an error
is detected during power up. Available options are “All errors”, “No errors”,
“All, But keyboard”, “All, But Diskette”, and “All But Disk/Key”.
BASE MEMORY:
Displays the amount of conventional memory detected during boot up.
EXTENDED MEMORY:
Displays the amount of extended memory detected during boot up.
TOTAL MEMORY:
Displays the total memory available in the system.
Page: 4-6
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
HARD DISK ATTRIBUTES:
Type
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
47
Cylinders
306
615
615
940
940
615
642
733
900
820
855
855
306
733
000
612
977
977
1024
733
733
733
306
977
1024
1224
1224
1224
1024
1024
918
925
1024
1024
1024
1024
1024
1024
918
820
1024
1024
809
809
776
Heads
4
4
6
8
6
4
8
5
15
3
5
7
8
7
0
4
5
7
7
5
7
5
4
5
9
7
11
15
8
11
11
9
10
12
13
14
2
16
15
6
5
5
6
6
8
V-P comp
128
300
300
512
512
65535
256
65535
65535
65535
65535
65535
128
65535
0000
0000
300
65535
512
300
300
300
0000
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65535
65335
AUTO
LZone
305
615
615
940
940
615
511
733
901
820
855
855
319
733
000
663
977
977
1023
732
732
733
336
976
1023
1223
1223
1223
1023
1023
1023
926
1023
1023
1023
1023
1023
1023
1023
820
1023
1023
852
852
775
Sect
17
17
17
17
17
17
17
17
17
17
17
17
17
17
00
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
26
17
26
33
Capacity
10
20
30
62
46
20
30
30
112
20
35
49
20
42
00
20
40
56
59
30
42
30
10
40
76
71
111
152
68
93
83
69
85
102
110
119
17
136
114
40
42
65
40
61
100
Award Hard Disk Type Table
PMB-601LF USER′S MANUAL
Page: 4-7
Chapter
4
Award BIOS Setup
4-4. THE ADVANCED BIOS FEATURES
Choose the〝ADVANCED BIOS FEATURES〞in the main menu, the screen
shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
▶ CPU Feature
▶ Hard Disk Boot Priority
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Boot Up Floppy Seek
Typematic Rate Setting
x Typematic Rate (Chars/Sec)
x Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control For OS
[Press Enter]
[Press Enter]
[Hard Disk]
[Hard Disk]
[LS120]
[Enabled]
[Enabled]
[Disabled]
6
250
[Setup]
[Enabled]
[1.4]
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
BIOS Features Setup Screen
The “BIOS FEATURES SETUP” allow you to configure your system for
basic operation. The user can select the system’s boot-up sequence and
security.
A brief introduction of each setting is given below.
Page: 4-8
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
CPU FEATURE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
CPU Feature
Limit CPUID MaxVal
Execute Disable Bit
Virtualization Technology
[Disabled]
[Enabled]
[Enabled]
Item Help
Menu Level ►
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. LIMIT CPUID MAXVAL
The CPUID instruction of some CPUs will return a value greater than
3.If you are using Windows operating system. Please disable this
feature.
2. EXECUTE DISABLE BIT
To select enable or disable the No-Execution Page Protection
Technology.
3. VITRUALIZATION TECHNOLOGY
To select enable or disable Virtualization Technology.
PMB-601LF USER′S MANUAL
Page: 4-9
Chapter
4
Award BIOS Setup
HARD DISK BOOT PRIORITY:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
Hard Disk Boot Priority
1.
2.
SATA 1. : HDS728080PLA380
Bootable Add-in Cards
Item Help
Menu Level
►
Use<Ç> or <È> to select a
device, then press <+> to move
it up, or <-> to move it down
the list. Press <ESC> to exit
this menu.
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Select Hard Disk Boot Device Priority
FIRST/SECOND/ THIRD/ OTHER BOOT DEVICE:
The BIOS attempt to load the operating system from the devices in the
sequence selected in these items.
BOOT UP FLOPPY SEEK:
You may enable / disable this item to define whether the system will look for
a floppy disk drive to boot at power-on, or proceed directly to the hard disk
drive.
TYPEMATIC RATE SETTING:
Enable this item if you wish to be able to configure the characteristics of
your keyboard. Typematic refers to the way in which characters are entered
repeatedly if a key is held down. For example, if you press and hold down
the "A" key, the letter "a" will repeatedly appear on your screen on your
screen until you release the key. When enabled, the typematic rate and
typematic delay can be selected.
Page: 4-10
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
TYPEMATIC RATE (CHARS/SEC):
This item sets the number of times a second to repeat a key stroke when you
hold the key down.
TYPEMATIC DELAY (MSEC):
The item sets the delay time after the key is held down before it begins to
repeat the keystroke.
SECURITY OPTION:
This category allows you to limit access to the system and Setup, or just to
Setup.
System
The system will not boot and access to Setup will be
denied if the correct password is not entered at the
prompt.
Setup
The system will boot, but access to Setup will be
denied if the correct password is not entered at the
prompt.
To disable security, select PASSWORD SETTING at Main Menu and
then you will be asked to enter password. Do not type anything and just
press <Enter>, it will disable security. Once the security is disabled, the
system will boot and you can enter Setup freely.
APIC MODE:
To Enable Advanced Programmable Interrupt Controller
MPS VERSION CONTROL FOR OS:
This option is only valid for multiprocessor motherboards as it specifies the
version of the Multiprocessor Specification (MPS) that the motherboard will
use. The MPS is a specification by which PC manufacturers design and build
Intel architecture systems with two or more processors.
PMB-601LF USER′S MANUAL
Page: 4-11
Chapter
4
Award BIOS Setup
4-5. ADVANCED CHIPSET FEATURES
Choose the〝ADVANCED CHIPSET FEATURES〞from the main menu,
the screen shown as below.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
X CAS Latency Time
X DRAM RAS# to CAS# Delay
X DRAM RAS# Precharge
X Precharge dealy (tRAS)
X System Memory Frequency
Memory Hole At 15M-16M
[By SPD]
Auto
Auto
Auto
Auto
By SPD
[Disabled]
** VGA Setting **
PEG/Onchip VGA Control
On-Chip Frame Buffer Size
DVMT Mode
DVMT/ FIXED Memory Size
[Auto]
[8MB]
[DVMT]
[128 MB]
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Chipset Features Setup Screen
This parameter allows you to configure the system based on the specific
features of the installed chipset. The chipset manages bus speed and
access to system memory resources, such as DRAM and the external cache.
It also coordinates communications between conventional ISA bus and the
PCI bus. It must be stated that these items should never need to be altered.
The default settings have been chosen because they provide the best operating conditions for the system. The only time you might consider making
any changes would be if you discovered that data was being lost while
using your system.
DRAM TIMEING SELECTABLE:
The value in this field depends on performance parameters of the installed
memory chips (DRAM). Do not change the value from the factory setting
unless you install new memory that has a different performance rating than
the original DRAMs.
Page: 4-12
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
CAS LATENCY TIME:
When synchronous DRAM is installed, the number of clock cycles of CAS
latency depends on the DRAM timing.
DRAM RAS# TO CAS# DELAY:
This item let you insert a timing delay between the CAS and RAS strobe
signals, used when DRAM is written to, read from, or refreshed. Fast
gives faster performance; and Slow gives more stable performance. This
field applies only when synchronous DRAM is installed in the system.
The choices are 2 and 3.
DRAM RAS# PRECHARGE TIME:
If an insufficient number of cycles is allowed for the RAS to accumulate its
charge before DRAM refresh, the refresh may be incomplete and the DRAM
may fail to retain data. Fast gives faster performance; and Slow gives more
stable performance. This field applies only when synchronous DRAM is
installed in the system. The choices are 2 & 3.
PRECHARGE DEALY (tRAS):
Precharge Delay This setting controls the precharge delay, which
determines the timing delay for DRAM precharge
SYSTEM MEMORY FREQUENCY:
Allow to choose different frequency of memory module.
MEMORY HOLE AT 15-16M:
You can reserve this area of system memory for ISA adapter ROM. When
this area is reserved, it cannot be cached. The user information of
peripherals that need to use this area of system memory usually discusses their
memory requirements
PEG/ONCHIP VGA CONTROL:
To select the PCI-Express Graphics or onchip VGA Graphics.
ON-CHIP FRAME BUFFER SIZE:
The On-Chip Frame Buffer Size can be set as 32MB. This memory is shared
with the system memory.
DVMT MODE:
Intel Dynamic Video Memory Technology Mode.
PMB-601LF USER′S MANUAL
Page: 4-13
Chapter
4
Award BIOS Setup
DVMT/FIXED MEMORY SIZE:
DVMT Memory Size Select.
4-6. INTEGRATED PERIPHERALS
Choose〝INTEGRATED PERIPHERALS〞from the main setup menu, a
display will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
X OnChip IDE Device
X SuperIO Device
Onboard Serial Port 3
Serial Port 3 Use IRQ
Onboard Serial Port 4
Serial Port 3 Use IRQ
X USB Device Setting
Onboard Lan1 Controller
Onboard Lan2 Controller
[Press Enter]
[Press Enter]
[3E8]
[IRQ10]
[2E8]
IRQ11]
[Press Enter]
[Enabled]
[Enabled]
Item Help
Menu Level ►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Integrated Peripherals Setup Screen
By moving the cursor to the desired selection and by pressing the <F1> key,
the all options for the desired selection will be displayed for choice.
If bios setup menu item supports USB device boot, it will cause Win9x detects
the same storages twice when the system is rebooted, and USB HDD will fail.
Note: this cause just happen under Win9x, the phenomenon is a limitation.
Page: 4-14
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
ONCHIP IDE DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
OnChip IDE Device
IDE HDD Block Mode
IDE DMA transfer access
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
SATA Mode
[Enabled]
[Enabled]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[IDE]
Item Help
Menu Level
►
If your IDE hard drive
supports block mode
select Enabled for
automatic detection of
the optional number of
block read/writes per
sector the drive can
support.
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. IDE HDD BLOCK MODE
Block mode is also called block transfer, multiple commands, or
multiple sector read/write. If your IDE hard drive supports block mode
(most new drives do), select Enabled for automatic detection of the
optimal number of block read/writes per sector the drive can support
2. IDE DMA TRANSTER ACCESS
To Enable/Disable the IDE DMA transfer access
3. PRIMARY MASTER/SLAVE PIO
SECONDARY MASTER/SLAVE PIO
The four IDE PIO fields allow you to set a PIO mode (0-4) for each of
the four IDE devices that the onboard IDE interface supports. Modes
0 through 4 provide successively increased performance. In Auto
mode, the system automatically determines the best mode for each
device.
PMB-601LF USER′S MANUAL
Page: 4-15
Chapter
4.
5.
4
Award BIOS Setup
PRIMARY MASTER/SLAVE UDMA
SECONDARY MASTER/SLAVE UDMA
Ultra DMA/33 implementation is possible only if your IDE hard drive
supports it and the operating environment includes a DMA driver
(Windows 95 OSR2 or a third-party IDE bus master driver). If you
hard drive and your system software both support Ultra DMA/33,
select Auto to enable BIOS support.
SATA MODE
Set the Serial ATA configuration. When set in Advanced Host
Controller Interface (AHCI) or RAID mode, the SATA controller is set
to Native mode. Configuration options: [IDE] [RAID] [AHCI]
SUPER IO DEVICE:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
SuperIO Device
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
X UR2 Duplex Mode
Onboard Parallel Port
Parallel Port Mode
X ECP Mode Use DMA
PWRON After PWR-Fail
[Enabled]
[3F8/IRQ4]
[2F8/IRQ3]
[Normal]
[Half]
[378/IRQ7]
[SPP]
3
[Off]
Item Help
Menu Level
►
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. ONBOARD FDC CONTROLLER
Select Enabled if the system has a floppy disk controller (FDC) installed
on the system board and you wish to use it. If you install and-in FDC or
the system has no floppy drive, select Disabled.
2. ONBOARD SERIAL PORT 1/2
Select an address and corresponding interrupt for the first and second
serial ports.
3. UART MODE SELECT
This item allows you to select UART mode.
Page: 4-16
PMB-601LF USER′S MANUAL
Chapter
4.
5.
6.
7.
8.
4
Award BIOS Setup
UR2 DUPLEX MODE
This item allows you to select the IR half/full duplex function.
ONBOARD PARALLEL PORT
This item allows you to determine access onboard parallel port
controller with which I/O address.
PARALLEL PORT MODE
Select an operating mode for the onboard parallel (printer) port.
Select Normal, Compatible, or SPP unless you are certain your
hardware and software both support one of the other available modes.
ECP MODE USE DMA
Select a DMA channel for the parallel port for use during ECP mode.
PWRON AFTER PWR-FAIL
This item allows you to select if you want to power on the system after
power failure. The choice:Off,On,Former-Sts.
ONBOARD SERIAL PORT 3/4:
SERIAL PORT 3/4 USE IRQ:
Select an address and corresponding interrupt for third and forth serial port.
USB DEVICE SETTING:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
Onboard Device
USB 1.0 Controller
USB 2.0 Controller
USB Keyboard Function
USB Mouse Function
USB Storage Function
[Enabled]
[Enabled]
[Enabled]
[Enabled]
[Enabled]
Item Help
Menu Level
►
*** USB Mass Storage Device Boot Setting ***
USB Flash Disk 2.00
[Auto mode]
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
PMB-601LF USER′S MANUAL
Page: 4-17
Chapter
1.
2.
3.
4.
5.
6.
4
Award BIOS Setup
USB 1.0 CONTROLLER
This should be enabled if your system has a USB installed on the
system board and you want to use it. Even when so equipped, if you
add a higher performance controller, you will need to disable this
feature.
USB 2.0 CONTROLLER
Enable the USB 2.0 controller.
USB KEYBOARD FUNCTION
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB keyboard.
USB MOUSE FUNCTION
Select Enabled if your system contains a Universal Serial Bus (USB)
controller and you have a USB Mouse.
USB STORAGE FUNCTION
Enable the USB Storage Function
USB FLASH DISK 2.00
Select USB Flash Disk Type.
ONBOARD LAN 1/2 CONTROLLER:
Enable the LAN controller.
Page: 4-18
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-7. POWER MANAGEMENT SETUP
Choose〝POWER MANAGEMENT SETUP〞option on the main menu, a
display will be shown on screen as below :
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function
Power Management
Suspend Mode
Soft-Off by PWR-BTTN
Wake-Up by PCI card
Resume by Alarm
X Date (of Month) Alarm
X Time (hh:mm:ss) Alarm
[Enabled]
[User Define]
[Disabled]
[Instant-Off]
[Enabled]
[Disabled]
0
0 : 0: 0
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
Power Management Setup Screen
The “Power Management Setup” allows the user to configure the system to
the most effectively save energy while operating in a manner consistent with
your own style of computer use.
ACPI FUNCTION:
Users are allowed to enable or disable the Advanced Configuration and
Power Management (ACPI).
PMB-601LF USER′S MANUAL
Page: 4-19
Chapter
4
Award BIOS Setup
POWER MANAGEMENT:
This item allows the user to select the type or degree of power saving and is
directly related to the following modes:
a. HDD Power Down
b. Suspend Mode
SUSPEND MODE:
When enabled and after the set time of system inactivity, all devices except
the CPU will be shut off.
SOFT-OFF BY PWR-BTTN:
Pressing the power button for more than 4 seconds forces the system to
enter the Soft-Off state when the system has “hung”. The choices are
Delay 4 Sec and Instant-Off.
WAKE-UP BY PCI CARD:
An input signal on the serial Ring Indicator (RI) line (in other words, an
incoming call on the modem) awakens the system from the soft-off state.
RESUME BY ALARM:
When enabled, you can set the date and time at which the RTC alarm
awakens the system from Suspend mode.
Page: 4-20
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-8. PNP/PCI CONFIGURATION
Choose 〝PNP/PCI CONFIGURATION〞 from the main menu, a display
will be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Init Display First
Reset Configuration Data
[PCI Slot]
[Disabled]
[Auto (ESCD)]
Press Enter
Resources Controlled By
x IRQ Resources
PCI/VGA Palette Snoop
[Disabled]
** PCI Express relative items **
Maximum Payload Size
[128]
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
PNP/PCI Configuration Setup Screen
The PNP/PCI Configuration Setup describes how to configure PCI bus system.
PCI, also known as Personal Computer Interconnect, is a system, which
allows I/O devices to operate at speeds nearing the speed of the CPU itself
uses when communicating with its own special components.
This section covers technical items, which is strongly recommended for
experienced users only.
INIT DISPLAY FIRST:
This item allows you to decide to active whether PCI Slot or on-chip VGA
first.
RESET CONFIGURATION DATA:
Normally, you leave this field Disabled. Select Enabled to reset Extended
System Configuration Data (ESCD) when you exit Setup if you have
installed a new add-on and the system configuration has caused such a
serious conflict that the operating system cannot boot.
PMB-601LF USER′S MANUAL
Page: 4-21
Chapter
4
Award BIOS Setup
RESOURCE CONTROLLED BY:
The Award Plug and Play Bios can automatically configure all of the booth
and Plug and Play-compatible devices. However, this capability means
absolutely nothing unless you are using a Plug and Play operating system
such as Windows 95. By choosing “manual”, you are allowed to
configure the IRQ Resources and DMA Resources.
IRQ RESOURCES:
The options for these items are found in its sub menu. By pressing the
<ENTER> key, you are prompt to enter the sub menu of the detailed options
as shown below:
Phoenix – Award CMOS Setup Utility
IRQ Resources
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
[PCI Device]
IRQ-3 assigned to
IRQ-4 assigned to
IRQ-5 assigned to
IRQ-7 assigned to
IRQ-9 assigned to
IRQ-10 assigned to
IRQ-11 assigned to
IRQ-12 assigned to
IRQ-14 assigned to
IRQ-15 assigned to
Item Help
Menu Level ►
Legacy ISA for devices
compliant with the original PC
AT bus specification, PCI/ISA
PnP for devices compliant
with the Plug and Play
standard whether designed for
PCI or ISA bus architecture
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Descriptions on each item above are as follows:
1. IRQ-n Assigned to:
You may assign each system interrupt a type, depending on the type of
device using the interrupt.
PCI/VGA PALETTE SNOOP:
Leave this field at disabled.
MAXIMUM PAYLOAD SIZE:
To select the maximum payload size of PCI Express devices.
Page: 4-22
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-9. PC HEALTH STATUS
Choose 〝PC HEALTH STATUS〞 from the main menu, a display will
be shown on screen as below:
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
Shutdown Temperature
Vcore
+1.8V
+3.3V
+12V
+5V
System Temperature
CPU Temperature
CPU FAN
System FAN
Power FAN
[Enabled]
1.26V
1.79V
3.28V
12.03V
4.91V
27 C
33 C
2556 RPM
8035 RPM
0 RPM
Item Help
Menu Level
►
↑↓→←: Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6: Fail-Safe Defaults
F7:Optimized Defaults
PC Health Status Setup Screen
The PC Health Status Setup allows you to select whether to choose between
monitoring or to ignore the hardware monitoring function of your system.
SHUTDOWN TEMPERATURE:
This item allows you to set up the CPU shutdown Temperature.
VCORE:
This item shows you the current system voltage.
1.8V/3.3V/12V / 5V :
Show you the voltage of 1.8V/3.3V/12V/5V.
SYSTEM/CPU TEMPERATURE:
This item shows you the current System/CPU temperature.
CPU/SYSTEM/POWER FAN:
This item shows you the current CPU/ SYSTEM /Power FAN speed.
PMB-601LF USER′S MANUAL
Page: 4-23
Chapter
4
Award BIOS Setup
4-10. FREQUENCY/VOLTAGE CONTROL
Choose 〝FREQUENCY CONTROL〞 from the main menu, a display
will be shown on screen as below:
Phoenix – AwardBIOS CMOS Setup Utility
Frequency Control
Auto Detect PCI Clk
Spread Spectrum
[Enabled]
[Enabled]
Item Help
Menu Level
▶
↑↓→←:Move Enter: Select +/-/PU/PD:Value F10:Save ESC:Exit F1:General Help
F5: Previous Values
F6:Fail-Safe Defaults
F7:Optimized Defaults
Frequency / Voltage Control Setup Screen
AUTO DETECT DIMM/PCI CLK:
This item allows you to enable or disable auto detect DIMM/PCI Clock.
SPREAD SPECTRUM:
This item allows you to enable or disable the spread spectrum modulate.
Page: 4-24
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-11. LOAD FAIL-SAFE DEFAULTS
By pressing the <ENTER> key on this item, you get a confirmation dialog
box with a message similar to the following:
Load Fail-Safe Defaults ( Y/N ) ? N
To use the BIOS default values, change the prompt to "Y" and press the
<Enter > key. CMOS is loaded automatically when you power up the
system.
4-12. LOAD OPTIMIZED DEFAULTS
When you press <Enter> on this category, you get a confirmation dialog
box with a message similar to the following:
Load Optimized Defaults ( Y/N ) ? N
Pressing "Y" loads the default values that are factory setting for optimal
performance system operations.
PMB-601LF USER′S MANUAL
Page: 4-25
Chapter
4
Award BIOS Setup
4-13. PASSWORD SETTING
User is allowed to set either supervisor or user password, or both of them.
The difference is that the supervisor password can enter and change the
options of the setup menus while the user password can enter only but do not
have the authority to change the options of the setup menus.
TO SET A PASSWORD
When you select this function, the following message will appear at the
center of the screen to assist you in creating a password.
Enter Password:
Type the password up to eight characters in length, and press < Enter >.
The password typed now will clear any previously entered password from
CMOS memory. You will be asked to confirm the password. Type the
password again and press the < Enter > key. You may also press < Esc >
to abort the selection and not enter a password.
User should bear in mind that when a password is set, you will be
asked to enter the password everything you enter CMOS setup Menu.
TO DISABLE THE PASSWORD
To disable the password, select this function (do not enter any key when
you are prompt to enter a password), and press the <Enter> key and a
message will appear at the center of the screen:
PASSWORD DISABLED!!!
Press any key to continue...
Press the < Enter > key again and the password will be disabled. Once the
password is disabled, you can enter Setup freely.
Page: 4-26
PMB-601LF USER′S MANUAL
Chapter
4
Award BIOS Setup
4-14. SAVE & EXIT SETUP
After you have completed adjusting all the settings as required, you must
remember to save these setting into the CMOS RAM. To save the settings,
select “SAVE & EXIT SETUP” and press <Enter>, a display will be shown
as follows:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
Load Fail-Safe Defaults
►Advanced BIOS Features
Load Optimized Defaults
►Advanced Chipset Features
Set Supervisor Password
►Integrated Peripherals
word
►Power Management Save to CMOS and EXIT Y/N)? Y
etup
►PnP/PCI Configura
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
↑↓→← : Select Item
Save Data to CMOS
When you confirm that you wish to save the settings, your system will be
automatically restarted and the changes you have made will be implemented.
You may always call up the setup program at any time to adjust any of the
individual items by pressing the <Del> key during boot up.
PMB-601LF USER′S MANUAL
Page: 4-27
Chapter
4
Award BIOS Setup
4-15. EXIT WITHOUT SAVING
If you wish to cancel any changes you have made, you may select the
“EXIT WITHOUT SAVING” and the original setting stored in the CMOS
will be retained. The screen will be shown as below:
Phoenix - AwardBIOS CMOS Setup Utility
►Standard CMOS Features
Load Fail-Safe Defaults
►Advanced BIOS Features
Load Optimized Defaults
►Advanced Chipset Features
Set Supervisor Password
word
►Integrated Peripherals
Quit Without Saving (Y/N)? N
►Power Management
etup
►PnP/PCI Configura
Saving
►PC Health Status
Esc : Quit
F10 : Save & Exit Setup
↑↓→← : Select Item
Abandon all Datas
Page: 4-28
PMB-601LF USER′S MANUAL
APPENDIX
EXPANSION BUS
A
This appendix indicates the pin assignments.
Section includes:
z PCI BUS Pin Assignment
Page: A-1
Appendix
A
Expansion Bus
PCI BUS PIN ASSIGNMENT
Like ISA-BUS connector, the PCI-BUS edge connector is also divided into two
sets: one consists of 98-pin; the other consists of 22-pin.
The pin assignments are as follows :
B1
B49 B52
B62
A1
A49 A52
A62
B
A
B
A
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
PIN
ASSIGNMENT
B1
B2
B3
B4
B5
B6
B7
B8
B9
B10
B11
B12
B13
B14
B15
B16
B17
B18
B19
B20
B21
B22
B23
B24
B25
B26
B27
B28
B29
B30
-12V
TCK
GND
TDO
+5V
+5V
INTB#
INTD#
REQ3#
REQ1#
GNT3#
GND
GND
CLKA
GND
CLKB
GND
REQ0#
+5V(I/O)
AD31
AD29
GND
AD27
AD25
+3.3V
C/BE3#
AD23
GND
AD21
AD19
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
TRST#
+12V
TMS
TDI
+5V
INTA#
INTC#
+5V
CLKC
+5V(I/O)
CLKD
GND
GND
GNT1#
RST#
+5V(I/O)
GNT0#
GND
REQ2#
AD30
+3.3V
AD28
AD26
GND
AD24
GNT2#
+3.3V
AD22
AD20
GND
B31
B32
B33
B34
B35
B36
B37
B38
B39
B40
B41
B42
B43
B44
B45
B46
B47
B48
B49
B52
B53
B54
B55
B56
B57
B58
B59
B60
B61
B62
+3.3V
AD17
C/BE2#
GND
IRDY#
+3.3V
DEVSEL#
GND
LOCK#
PERR#
+3.3V
SERR#
+3.3V
C/BE1#
AD14
GND
AD12
AD10
GND
AD08
AD07
+3.3V
AD05
AD03
GND
AD01
+5V(I/O)
ACK64#
+5V
+5V
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A52
A53
A54
A55
A56
A57
A58
A59
A60
A61
A62
AD18
AD16
+3.3V
FRAME#
GND
TRDY#
GND
STOP#
+3.3V
SDONE
SB0#
GND
PAR
AD15
+3.3V
AD13
AD11
GND
AD09
C/BE0#
+3.3V
AD06
AD04
GND
AD02
AD00
+5V(I/O)
REQ64#
+5V
+5V
Page: A-2
PMB-601LF USER′S MANUAL
APPENDIX
TECHNICAL
SUMMARY
B
This section introduce you the maps concisely.
Section includes:
z Block Diagram
z Interrupt Map
z RTC & CMOS RAM Map
z Timer & DMA Channels Map
z I / O & Memory Map
Page: B-1
Appendix
B
Technical Summary
BLOCK DIAGRAM
Page: B-2
PMB-601LF USER′S MANUAL
Appendix
B
Technical Summary
INTERRUPT MAP
IRQ
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
ASSIGNMENT
System TIMER
Keyboard
Cascade
Serial port 2
Serial port 1
Available
Floppy
Parallel port 1
RTC clock
Available
Available
Available
PS/2 Mouse
Math coprocessor
IDE1
IDE2
PMB-601LF USER′S MANUAL
Page: B-3
Appendix
B
Technical Summary
RTC & CMOS RAM MAP
CODE
00
01
02
03
04
05
06
07
08
09
0A
0B
0C
0D
0E
0F
10
11
12
13
14
15
16
17
18
30
31
32
33
34-3F
40-7f
Page: B-4
ASSIGNMENT
Seconds
Second alarm
Minutes
Minutes alarm
Hours
Hours alarm
Day of week
Day of month
Month
Year
Status register A
Status register B
Status register C
Status register D
Diagnostic status byte
Shutdown byte
Floppy Disk drive type byte
Reserve
Hard Disk type byte
Reserve
Equipment byte
Base memory low byte
Base memory high byte
Extension memory low byte
Extension memory high byte
Reserved for extension memory low byte
Reserved for extension memory high byte
Date Century byte
Information Flag
Reserve
Reserved for Chipset Setting Data
PMB-601LF USER′S MANUAL
Appendix
B
Technical Summary
TIMER & DMA CHANNELS MAP
Timer Channel Map :
Timer Channel
0
1
2
Assignment
System timer interrupt
DRAM Refresh request
Speaker tone generator
DMA Channel Map :
DMA Channel
0
1
2
3
4
5
6
7
Assignment
Available
Available
Floppy
Available
Cascade
Available
Available
Available
PMB-601LF USER′S MANUAL
Page: B-5
Appendix
B
Technical Summary
I/O & MEMORY MAP
Memory Map :
MEMORY MAP
0000000-009FFFF
00A0000-00BFFFF
00C0000-00DFFFF
00E0000-00EFFFF
00F0000-00FFFFF
0100000-FFFFFFF
ASSIGNMENT
System memory used by DOS and
application
Display buffer memory for VGA/ EGA /
CGA / MONOCHROME adapter
Reserved for I/O device BIOS ROM or
RAM buffer.
Reserved for PCI device ROM
System BIOS ROM
System extension memory
I/O Map :
I/O MAP
000-01F
020-021
022-023
040-05F
060-06F
070-07F
080-09F
0A0-0BF
0C0-0DF
0F0-0FF
1F0-1F8
278-27F
2B0-2DF
2F8-2FF
360-36F
378-37F
3B0-3BF
3C0-3CF
3D0-3DF
3F0-3F7
3F8-3FF
Page: B-6
ASSIGNMENT
DMA controller (Master)
Interrupt controller (Master)
Chipset controller registers I/O ports.
Timer control regsiters.
Keyboard interface controller (8042)
RTC ports & CMOS I/O ports
DMA register
Interrupt controller (Slave)
DMA controller (Slave)
Math coprocessor
Hard Disk controller
Parallel port-2
Graphics adapter controller
Serial port-2
Net work ports
Parallel port-1
Monochrome & Printer adapter
EGA adapter
CGA adapter
Floppy disk controller
Serial port-1
PMB-601LF USER′S MANUAL
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement