JVC | 0209RYMMDWDAT | User's Manual | JVC 0209RYMMDWDAT User's Manual

JVC 0209RYMMDWDAT User's Manual
Warnings, Cautions and Others
Mises en garde, précautions et indications
diverses
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni
le coffret de l’appareil. Il n’y a aucune pièce réparable
par l’utilisateur à l’intérieur de l’appareil; confiez toute
réparation à un personnel qualifié.
3. ATTENTION: Rayonnement laser visible et/ou invisible
de classe 1M une fois ouvert. Ne pas regarder directement
dans le faisceau avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.
MICRO COMPONENT SYSTEM
UX-GN6
—Consists of CA-UXGN6 and SP-UXGN5
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Thank you for purchasing a JVC product.
INSTRUCTIONS
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the
areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate
air path for ventilation by placing on a stand with a height
of 10 cm or more.
The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
Basic and Common Operations
Remote sensor
STANDBY lamp
Point at the remote sensor on the front panel.
Press
To
ATTENTION: Aération correcte
Pour prévenir tout risque de décharge électrique ou
d’incendie et éviter toute détérioration, installez l’appareil de
la manière suivante:
1. Avant: Bien dégagé de tout objet.
2. Côtés/dessus/dessous: Assurez-vous que rien ne bloque
les espaces indiqués sur le schéma ci-dessous.
3. Dessous: Posez l’appareil sur une surface plane et
horizontale. Veillez à ce que sa ventilation correcte puisse
se faire en le plaçant sur un support d’au moins dix
centimètres de hauteur.
Front/Face
Side/Côté
Main
unit
Indication/Result
Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
See “Listening to an iPod/Viewing Images on the iPod”
on page 5.
Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as
the source.
• See “Listening to FM and AM Broadcasts” or “Listening
to Other Equipment” on page 5.
Adjust the volume
LVT1989-001A[J/C]
0209RYMMDWDAT
CAUTION
The
button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
ATTENTION
La touche , quelle que soit sa position, ne coupe pas la
ligne principale.
Débrancher la fiche principale pour couper complètement
l’alimentation du secteur (le témoin STANDBY s’éteint).
La fiche secteur ou un coupleur est utilisé comme dispositif
de déconnexion de l’appareil, et l’appareil déconnecté doit
être prêt à être utilisé.
• Quand l’appareil est en mode d’attente, le témoin STANDBY
est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY s’éteint.
L’alimentation peut être commandée à distance.
©2009 Victor Company of Japan, Limited
For customer use:
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
For U.S.A.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause
harmful interference to radio communications. However,
there is no guarantee that interference will not occur
in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which
can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
Le symbole de l’éclair à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur
la présence d’une “tension dangereuse” non
isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution
de personnes.
Le point d’exclamation à l’intérieur d’un
triangle équilatéral est destiné à alerter
l’utilisateur sur la présence d’opérations
d’entretien importantes au sujet desquelles
des renseignements se trouvent dans le
manuel d’instructions.
CAUTION:
Changes or modifications not approved by JVC could void
the user’s authority to operate the equipment.
WARNING: TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE.
CAUTION: Excessive sound pressure from earphones or
headphones can cause hearing loss.
ATTENTION: Une pression acoustique excessive des écouteurs
ou du casque d’écoute peut entraîner une perte auditive.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
—
CA-UXGN6
SP-UXGN5
SP-UXGN5
CA-UXGN6
ATTENTION:
• Ne bloquez pas les orifices ou les trous de ventilation. (Si
les orifices ou les trous de ventilation sont bloqués par un
journal un tissu, etc., la chaleur peut ne pas être évacuée
correctement de l’appareil.)
• Ne placez aucune source de flamme nue, telle qu’une
bougie, sur l’appareil.
• Lors de la mise au rebut des piles, veuillez prendre en
considération les problèmes de l’environnement et suivre
strictement les règles et les lois locales sur la mise au rebut
des piles.
• N’exposez pas cet appareil à la pluie, à l’humidité, à un
égouttement ou à des éclaboussures et ne placez pas des
objets remplis de liquide, tels qu’un vase, sur l’appareil.
CAUTION: Battery shall not be exposed to excessive heat
such as sunshine, fire, or the like.
ATTENTION: Les piles ne doivent en aucun cas être
exposées à une chaleur excessive (lumière du solei, feu,
etc.).
Headphones
(not supplied)
Stereo mini plug cord
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
• When the display demonstration is activated, it also starts if no
operation is done for about 2 minutes while the System is turned
on.
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
To use 4/¢
To use VOL +/–
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not work.
Touch to turn on the System.
The S.TURBO indicator lights up.
To cancel this function, press again.
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Press repeatedly when the System is turned on.
—
Change the display
brightness
Press repeatedly while the System is on standby.
Clock
DISP OFF: Turns off the display with the motion sensor
on.
ECO ON: Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
Playing Back a Disc/USB Mass Storage Class Device
Connections
Do not connect the AC power cord until all other connections have been made.
For iPod
To a wall outlet
Plug the AC power cord only after all
connections are complete.
To connect the monitor
(not supplied)
—To view video/picture
from the iPod
Video cord
(supplied)
Monitor
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Rear view
Touch to open the disc tray.
1
2
Basic Disc/USB Mass Storage Class Device Operations
To
Play back the disc
Press
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
Prepare the Remote Control
• When using an 8 cm (3 3/16 inch) disc, place it on
the inner circle of the disc tray.
Select a track
Indication/Result
• During playback, press again to pause.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Press and hold
Select a group
(MP3/WMA only)
Insulation sheet
Select the next groups.
Select the previous groups.
To Replace the Battery in the Remote Control
Release
Insert
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
Red
USB cable (not
supplied)
Red
USB memory
(not supplied)
Change
the display
information
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
(only for USB)
Press repeatedly.
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector.
Black
From right
speaker
Black
To assemble the AM loop antenna (supplied)
NOTES:
Turn the AM loop antenna until
the best reception is obtained.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
2
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
NOTES:
To connect the AM loop antenna
AM loop antenna
(supplied)
or
From left
speaker
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
(only for Disc)
1
Select disc as the source.
2
Activate the Program Play.
3
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
or
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m (3.3 ft).
• USB mass storage class device is charged through the USB terminal when the System
is turned on and the source is “USB.”
• You cannot connect a computer to the USB terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB terminal may
not be fully inserted into the USB terminal on the System. In such a case, use a USB
extension cable (not supplied) to connect.
5
6
•
•
•
•
To check the programmed contents, press 4 or ¢.
To add tracks, repeat steps 3 and 4 above.
To erase the entire program, press and hold CANCEL for about 2 seconds.
To exit from Program Play, press PROGRAM or 7.
– The stored program is kept.
1
Select disc as the source.
2
Press repeatedly to select the desired Random Mode.
RANDOM:
RND GRP:
Press repeatedly to specify the repeat mode as follows:
RPT TRK:
RPT GRP:
RPT ALL:
RPT OFF:
2
Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
The tracks are played back in the programmed
order.
Operations for Program Play (while not playing)
Playing Repeatedly—Repeat Play
1
Press to store the selected track.
4
Playing at Random—Random Play (only for Disc)
NOTES:
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
Programming the Playing Order—Program Play
Touch to close the disc tray.
3
Lithium coin battery
(product number: CR2025)
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which
contains Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
(canceled)
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
Turn off the display
while on standby
3
When you use the remote control for the first time, pull out
the insulation sheet.
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
—
NOTE:
To connect the speaker cords
NOTES:
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
(canceled)
[European Union only]
[Union européenne seulement]
Getting Started
Supplied Accessories
To restore the volume, press again, or adjust the
volume level.
—
Select the Sound
Mode
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
1
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN6J (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
• Video cord (× 1)
If anything is missing, consult your dealer immediately.
Drop the volume in
a moment
PHONES jack
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
Repeats the current (or specified) track. [ 1]
Repeats all tracks in the current group (MP3/WMA
only). [ ]
Repeats all tracks. [ ALL ]
Normal playback
3
Plays all tracks in random order. [ALL RND ]
Plays tracks in the current group in random
order. (MP3/WMA only). [ RND ]
RND OFF:
Normal playback
Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
or
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same
procedure.
4
LVT1989-001A EN_UX-GN6[JC]
Listening to an iPod/Viewing Images
on the iPod
Connecting an iPod
Insert the iPod directly to the connector pins.
To
Display the menu/
Go back to the
previous menu
Select an item on
the menu
Press
—
• The UP/DOWN buttons work
in the same way as operating
the click wheel of iPod
counterclockwise/clockwise.
(Refer to the instruction manual
for the iPod for details.)
or
Apple iPod (separately purchased)
Protective cap
Connector pins
Direct dock
for iPod
Dock adapter
(supplied with
the iPod or sold
separately)
To detach the dock adapter from the dock:
Pull up the dock adapter with your fingernail or sharp
pointed tool using the slot.
• Be careful not to injure your fingertips or damage the
terminal of the dock.
Presetting Stations
Indication/Result
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display
is flashing.
Press to select a preset number for the station you want to
store.
1
2
3
or
• Refer to the instruction manual for
the iPod for details.
• Refer to the instruction manual for
the iPod for details.
Press repeatedly.
Play back at
random
Play back
repeatedly
Change the display
information
Turn on iPod’s
backlight
Press and hold for more than
2 seconds.
Press to store the station.
4
Listening to Other Equipment
Front view
Digital Audio Player, etc.
Listening to FM and AM Broadcasts
Basic Tuner Operations
• Be sure to reduce the volume on the System to the minimum level before
connecting an iPod. Adjust the volume after starting playback.
• DO NOT connect or disconnect the iPod when the System is turned on.
• You cannot send any data to your iPod from the System.
• Do not carry the System with iPod connected. You might drop the iPod or it
might cause damages to the iPod dock.
• Do not touch or hit the iPod terminal pins or connector pins in the iPod dock
directly. It might cause damages to the connector part.
• Before viewing a video/picture from your iPod on your monitor, make the
appropriate video setting on the iPod. For details of the setting, refer to the
instruction manual for the iPod.
Basic iPod Operations
To
Play back an iPod
Press
Select a track
Indication/Result
The System detects the iPod and starts
playback.
• To turn off the iPod, press and hold for
more than 2 seconds.
Select the next tracks.
To
Select FM or AM
Press
Select a frequency
or
Tune in to a preset
station
• For presetting
stations, see the
right column.
Indication/Result
Press repeatedly to select “FM” or “AM.”
• The selected frequency band appears.
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.
Press repeatedly to select its preset number.
or
Press to improve reception.
The (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again.
The (stereo) indicator lights up.
Change the FM
reception mode
(When an FM
stereo broadcast is
hard to receive)
To go back to the beginning of the current
or previous tracks.
Forward search/
Reverse search
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
1
Turn the volume to minimum.
2
Press repeatedly to select “AUDIO IN.”
3
4
Start playing the connected equipment.
Adjust the volume.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO IN jack is too loud or too
quiet, you can change the audio input level through the AUDIO IN jack (without
changing the volume level).
Press repeatedly to select the level as follows:
Press and hold to fast-forward the track
during playback.
Press and hold to fast-reverse the track
during playback.
NORMAL:
HIGH:
Learning More about This System
Basic and Common Operations (see page 3)
Listening to an iPod/Viewing Images on the iPod (see
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
page 5)
• Compatible iPod:
Playing Back a Disc/USB Mass Storage Class Device
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from the
one you have intended while recording. If a folder (group)
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management)
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
iPod model
iPod nano 1GB/2GB/4GB
iPod nano (2nd Generation)
2GB/4GB/8GB
iPod nano (3rd Generation) 4GB/8GB
iPod nano (4th Generation) 8GB/16GB
iPod mini 4GB/6GB
iPod mini (2nd Generation) 4GB/6GB
iPod (4th Generation) 20GB/40GB
iPod classic 80GB/160GB
iPod photo (4th Generation)
20GB/30GB/40GB/60GB
iPod video (5th Generation)
30GB/60GB/80GB
iPod touch 8GB/16GB
iPod touch (2nd Generation) 8GB/16GB
AM 12:00
2
or
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of
the Daily Timers.
• To correct a misentry during the process, press MENU/CANCEL. You can return to
the previous step.
Press repeatedly to select one of the timer you want to
set—TIMER-1, TIMER-2, or TIMER-3.
1
Adjust the hour, then the minute.
Canceled
2
3
or
Setting the Sleep Timer
Press repeatedly to specify the time (in minutes) as follows:
(canceled)
The SLEEP indicator lights up and the display dims.
To check the remaining time until the System shuts off, press SLEEP once.
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB/iPod)
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System turns off.
To cancel this function, press the button again.
4
1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“DISC,” “USB HOST,”
“TUNER FM,” “TUNER AM,” “AUDIO IN,” or “IPOD.”
4 For “TUNER FM” or “TUNER AM”: Select a preset
channel.*
For “DISC” or “USB HOST”: Select a track. (For MP3/
WMA: Select the group, then the track number.)
5 Select the volume.
Turn off the System (on standby).
• When the on-time comes, the System starts playing
the specified source and sets the volume gradually
to the preset level.
* If no preset channel is stored, “NOMEMORY” appears. When the on time comes, the
System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time,
remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the
power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may
cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a
new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the
wall outlet, then consult your dealer. Using the System in this state may cause a
fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C
(41˚F) and 35˚C (95˚F).
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the
System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug
the power cord and consult your dealer.
Maintenance
To get the best performance of the System, keep your discs and mechanism clean.
To Turn Off the Daily Timer
1
Press repeatedly to select “TIMER-1,” “TIMER-2,” or “TIMER-3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing
TIMER, then press SET.
Handling discs
• Remove the disc from its case by holding it at the edge while pressing the center
hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe
it with a cloth soaked in water-diluted neutral detergent and wrung well, then
wipe clean with a dry cloth.
• Since the System may deteriorate in quality, become damaged or get its paint
peeled off, be careful about the following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact for a long time.
6
Audio Video
–
SOUND indicator
(See page 3.)
Source indicators
FM reception indicators
(See page 5.)
Timer mode indicators
(See page 6.)
Source indicators
–
File type indicators (See page 4.)
Main display
A.STBY (Auto Standby)
indicator (See page 6.)
SLEEP indicator (See page 6.)
Troubleshooting
–
–
–
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
iPod Operations
The iPod does not play, but “CONNECT” appears on the
display.
\ The iPod battery is low or exhausted. Charge the iPod
battery.
The video/picture from the iPod is not displayed on the
monitor.
\ The video settings on the iPod is incorrect. Refer to the
instruction manual for the iPod.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Ordinary input level.
Increases the input level.
Precautions
Setting the Daily Timer
1
HBS indicator
(See page 3.)
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
7
Setting the Clock and Using Timers
Setting the Clock
S.TURBO (Sound Turbo)
indicator (See page 3.)
Play mode indicators
(See page 4.)
• If incompatible iPod is connected, the iPod may not be
operated from the System.
• When an iPod is connected to the System, the battery in
the iPod is charged through the iPod terminal (except when
the ECO Mode is activated).
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion occurs,
it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction
manual.
5
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press MENU/CANCEL.
Press to activate the clock setting mode.
Display Information
Specifications
Amplifier section
OUTPUT POWER:
60 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no
more than 10% total harmonic distortion
Speakers/Impedance:
8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/50 kΩ (at “NORMAL”)
250 mV/50 kΩ (at “HIGH”)
Digital input:
USB
Tuner section
FM tuning range:
AM tuning range:
87.5 MHz - 108.0 MHz
530 kHz - 1 710 kHz
Disc player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
80 dB
85 dB
Immeasurable
USB storage
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
Compatible with USB 2.0 Full Speed
Mass storage class
FAT16, FAT32
DC 5 V
500 mA
iPod section
iPod output power:
VIDEO OUT:
DC 5 V
500 mA
Composite
BT-51018-5
(0306)
General
Power requirements:
Power consumption:
AC 120 V
, 60 Hz
36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
Dimensions (W x H x D): 165 mm x 250 mm x 272 mm
(6 1/2 inches x 9 7/8 inches x
10 3/4 inches)
Mass:
3.5 kg (7.8 lbs)
Speakers
Speaker units:
Impedance:
Dimensions (approx.):
(W x H x D)
Mass (approx.):
4 cm (1-5/8 inches) cone x 1
12 cm (4-3/4 inches) cone x 1
8Ω
140 mm x 250 mm x 183 mm
(5 9/16 inches x 9 7/8 inches x
7 1/4 inches)
1.8 kg (4.0 lbs) each
Specifications and appearance are subject to change without
prior notice.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
8
LVT1989-001A EN_UX-GN6[JC]
MICRO COMPONENT SYSTEM
UX-GN5
—Consists of CA-UXGN5 and SP-UXGN5
Thank you for purchasing a JVC product.
INSTRUCTIONS
LVT1988-001A[B]
0209RYMMDWDAT
©2009 Victor Company of Japan, Limited
Warnings, Cautions and Others
CAUTION
The
button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Dear Customer,
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue:
Neutral
Brown:
Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed
as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Products
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION:
Excessive sound pressure from earphones or headphones
can cause hearing loss.
CAUTION:
Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in
the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Side view
CA-UXGN5
SP-UXGN5
SP-UXGN5
Battery
Notice:
The sign Pb
below the
symbol for
batteries
indicates that
this battery
contains lead.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove
the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near
a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
• Do not block the vents.
Front view
Information for Users on Disposal of Old Equipment
and Batteries
CA-UXGN5
[European Union]
These symbols indicate that the electrical
and electronic equipment and the battery
with this symbol should not be disposed
of as general household waste at its endof-life. Instead, the products should be
handed over to the applicable collection
points for the recycling of electrical and
electronic equipment as well as batteries
for proper treatment, recovery and
recycling in accordance with your national
legislation and the Directive 2002/96/EC
and 2006/66/EC.
By disposing of these products correctly,
you will help to conserve natural resources
and will help to prevent potential negative
effects on the environment and human
health which could otherwise be caused
by inappropriate waste handling of these
products.
For more information about collection
points and recycling of these products,
please contact your local municipal office,
your household waste disposal service
or the shop where you purchased the
product.
Penalties may be applicable for incorrect
disposal of this waste, in accordance with
national legislation.
[Business users]
If you wish to dispose of this product,
please visit our web page
http://www.jvc.eu/ to obtain information
about the take-back of the product.
[Other Countries outside the European
Union]
These symbols are only valid in the
European Union.
If you wish to dispose of these items,
please do so in accordance with applicable
national legislation or other rules in your
country for the treatment of old electrical
and electronic equipment and batteries.
Supplied Accessories
Remote sensor
STANDBY lamp
Press
Point at the remote sensor on the front panel.
To
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
See “Listening to Other Equipment” on page 5.
Adjust the volume
—
Drop the volume in
a moment
PHONES jack
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
• When the display demonstration is activated, it also starts if no
operation is done for about 2 minutes while the System is turned
on.
Select the Sound
Mode
Headphones
(not supplied)
Stereo mini plug cord
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not work.
(canceled)
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
The S.TURBO indicator lights up.
To cancel this function, press again.
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Press repeatedly when the System is turned on.
—
Change the display
brightness
(canceled)
Touch to turn on the System.
Turn off the display
while on standby
Press repeatedly while the System is on standby.
Clock
To use VOL +/–
DISP OFF: Turns off the display with the motion sensor
on.
ECO ON: Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
1
3
Playing Back a Disc/USB Mass Storage Class Device
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Connections
Do not connect the AC power cord until all other connections have been made.
To a wall outlet
Plug the AC power cord only after all connections are complete.
Rear view
Touch to open the disc tray.
1
2
Basic Disc/USB Mass Storage Class Device Operations
To
Play back the disc
Press
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
When you use the remote control for the first time, pull out
the insulation sheet.
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Select a track
Press and hold
Insulation sheet
Select a group
(MP3/WMA only)
Indication/Result
• During playback, press again to pause.
Release
Insert
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
Red
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
Black
From right
speaker
Red
USB cable (not
supplied)
USB memory
(not supplied)
Change
the display
information
2
Activate the Program Play.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
3
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
To go back to the beginning of the current or
previous tracks.
4
Select the next groups.
5
6
or
From left
speaker
NOTES:
To connect the AM loop antenna
AM loop antenna
(supplied)
Turn AM loop antenna until
the best reception is obtained.
2
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than 1 m.
• USB mass storage class device is charged through the USB REC/PLAY terminal when
the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB REC/PLAY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB terminal may not
be fully inserted into the USB REC/PLAY terminal on the System. In such a case, use a
USB extension cable (not supplied) to connect.
or
•
•
•
•
To check the programmed contents, press 4 or ¢.
To add tracks, repeat steps 3 and 4 above.
To erase the entire program, press and hold CANCEL for about 2 seconds.
To exit from Program Play, press PROGRAM or 7.
– The stored program is kept.
1
Select disc as the source.
2
Press repeatedly to select the desired Random Mode.
RANDOM:
RND GRP:
Press repeatedly to specify the repeat mode as follows:
RPT TRK:
RPT GRP:
RPT ALL:
RPT OFF:
2
Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
The tracks are played back in the programmed
order.
Operations for Program Play (while not playing)
Playing Repeatedly—Repeat Play
1
Press to store the selected track.
Playing at Random—Random Play (only for Disc)
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
NOTES:
To assemble the AM loop antenna (supplied)
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
(only for USB)
Press repeatedly.
NOTES:
Black
(only for Disc)
Select disc as the source.
Select the previous groups.
Touch to close the disc tray.
3
Lithium coin battery
(product number: CR2025)
Programming the Playing Order—Program Play
1
To Replace the Battery in the Remote Control
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
—
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
To restore the volume, press again, or adjust the
volume level.
—
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
To connect the speaker cords
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Indication/Result
Remote
NOTE:
Prepare the Remote Control
NOTES:
Main
unit
Press repeatedly to select “FM” or “AM” as the source.
• See “Listening to FM and AM Broadcasts” on page 5.
To use 4/¢
Getting Started
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN5R (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
If anything is missing, consult your dealer immediately.
The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
Basic and Common Operations
Repeats the current (or specified) track. [ 1]
Repeats all tracks in the current group (MP3/WMA
only). [ ]
Repeats all tracks. [ ALL ]
Normal playback
3
Plays all tracks in random order. [ALL RND ]
Plays tracks in the current group in random
order. (MP3/WMA only). [ RND ]
RND OFF:
Normal playback
Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
or
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same
procedure.
4
LVT1988-001A EN_UX-GN5[B]
Listening to FM and AM Broadcasts
Basic Tuner Operations
To
Select FM or AM
Press
Select a
frequency
or
Tune in to a
preset station
• For presetting
stations, see
the right
column.
Indication/Result
Press repeatedly.
• The selected frequency
band appears.
Press and hold for more
than 2 seconds.
The System starts
searching for stations and
stops when a station of
sufficient signal strength
is tuned in.
• Press during searching
to stop.
• Press repeatedly to
change the frequency
step by step.
Press repeatedly to select
its preset number.
1
2
Press to improve
reception.
The (mono) indicator
lights up.
Stereo effect will be lost.
To restore the stereo
effect, press again. The
(stereo) indicator lights
up.
You can locate a particular kind of program from the preset
stations (see the left column) by specifying the PTY codes.
Press to enter the PTY code setting
mode.
The PTY code and “SELECT” appear
alternately.
Select a PTY code.
Front view
Digital Audio Player, etc.
or
Press to store the station.
Receiving FM Stations with Radio Data
System
The System searches for 30 preset FM
stations, stops when it finds the one
you have selected, and tunes in to that
station.
• To stop searching, press PTY SEARCH.
• To continue searching after it stops on an unwanted
station, press PTY SEARCH while the indications on the
display are flashing.
Radio Data System allows FM stations to send an additional
signal along with their regular program signals.
With the System, you can receive the following types of
Radio Data System signals.
PS (Program Service):
Shows commonly known
station names.
PTY (Program Type):
Shows types of broadcast
programs.
RT (Radio Text):
Shows text messages the
station sends.
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
3
NOTE:
Turn the volume to minimum.
1
Press to select “AUDIO IN.”
2
3
4
Start playing the connected equipment.
Adjust the volume.
If no program is found, “NOTFOUND” appears.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO
IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the
volume level).
NOTE:
If you want to know more about Radio Data System, visit
<http://www.rds.org.uk>.
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
Playing Back a Disc/USB Mass Storage Class Device
2
or
4
Basic and Common Operations (see page 3)
1
3
or
Change the FM
reception mode
(When an
FM stereo
broadcast is
hard to receive)
Searching for Programs by PTY Codes
(PTY Search)
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry
mode.
• Finish the following steps while the
indication on the display is flashing.
Press to select a preset number for the
station you want to store.
Press repeatedly to select the level as follows:
Changing the Radio Data System
Information
NORMAL:
HIGH:
Each time you press the button, the
information changes as follows:
Troubleshooting
Learning More about This System
Listening to Other
Equipment
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
(group) does not include MP3/WMA tracks, they are
ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are
interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Ordinary input level.
Increases the input level.
Display Information
Play mode indicators (See page 4.)
Frequency
(No Radio Data System signal)
NOTE:
Source indicator
HBS indicator (See page 3.)
S.TURBO (Sound Turbo)
indicator (See page 3.)
SOUND
indicator (See page 3.)
Source indicators
If no Radio Data System signals are sent by a station, “NO PS,”
“NO PTY,” or “NO RT” appears.
FM reception indicators
(See page 5.)
REC indicator
(See page 6.)
Main display
Setting the Clock and Using Timers
About SCMS (Serial Copy Management System)
(On the System)
2
• If you have programmed the playing order for CD (see
“Programming the Playing Order—Program Play” on page
4), the tracks are recorded in the programmed order if
Program Play is activated.
• To stop recording manually, press 7.
To erase tracks/groups
Setting the Sleep Timer
(canceled)
To check the remaining time until the System shuts off,
press SLEEP once.
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB)
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3 minutes,
the System turns off.
Select the target to erase.
TTL DEL: Delete a track.
GRP DEL: Delete a group.
DEL ALL: Delete all tracks.
To cancel this function, press the button again.
Display Messages for Recording Operations
NODEVICE
• No USB mass storage class device is connected or
the connected USB mass storage class device is not
compatible with this System.
D. (data) FULL
• The capacity of the USB mass storage class device is full.
FILEFULL
• The USB mass storage class device has exceeded the
maximum number of files it can support.
W. (write) PROT
• The USB mass storage class device is write-protected.
SCMS VLT (violation)
• You have tried to copy from a duplicated disc to the USB
mass storage class device.
D. (device) FAIL
• The System failed to read the USB mass storage class
device.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
4
1 Adjust the hour then the minute for
on-time.
2 Adjust the hour then the minute for
off-time.
3 Select the playback source—“TUNER
FM,” “TUNER AM,” “AUDIO IN,” “DISC,” or
“USB HOST.”
4 For “TUNER FM” or “TUNER AM”:
Select a preset channel.*
For “DISC” or “USB HOST”: Select a
track. (For MP3/WMA: Select the group,
then the track number.)
5 Select the volume.
Turn off the System (on standby).
• When the on-time comes, the System
starts playing the specified source and
sets the volume gradually to the preset
level.
* If no preset channel is stored, “NOMEMORY” appears. When the
on time comes, the System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
To Turn Off the Daily Timer
1
Press repeatedly to select “TIMER-1,”
“TIMER-2,” or “TIMER-3.”
To get the best performance of the System, keep your discs
and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
Specifications
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
Amplifier section
OUTPUT POWER:
120 W (60 W + 60 W) at 8 Ω (10% THD)
Speakers/Impedance:
8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “NORMAL”)
250 mV/47 kΩ (at “HIGH”)
Digital input:
USB REC/PLAY
This equipment has been designed and manufactured to meet international safety standards but, like any electrical
equipment, care must be taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between
pieces of equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and
withdraw the mains plug when making or changing connections.
Tuner section
FM tuning range:
87.50 MHz – 108.00 MHz
AM (MW) tuning range: 522 kHz – 1629 kHz
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
Disc player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
80 dB
85 dB
Immeasurable
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any
way—switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
USB storage
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended
operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
Compatible with USB 2.0 Full Speed
Mass storage class
FAT16, FAT32
DC 5 V
500 mA
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic
safety. It is illegal to watch television whilst driving.
General
Power requirements:
Power consumption:
Dimensions (approx.):
Mass (approx.):
AC 230 V
, 50 Hz
36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
165 mm x 250 mm x 272 mm
(W x H x D)
3.5 kg
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
Speakers
Speaker units:
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Impedance:
Dimensions (approx.):
Mass (approx.):
ABOVE ALL
4 cm cone x 1
12 cm cone x 1
8Ω
140 mm x 250 mm x 183 mm
(W x H x D)
1.8 kg each
– NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case
—this could result in a fatal electrical shock.
– NEVER guess or take chances with electrical equipment of any kind—it is better to be safe than sorry!
Specifications and appearance are subject to change without
prior notice.
2
4
5
or
The SLEEP indicator lights up and the display
dims.
You can erase tracks/groups on the USB mass storage class
device.
• Once the tracks are erased, you cannot recover them.
• To quit erasing, press 7.
Select a track/group you want to erase while playback
is stopped. (See page 4.)
or
3
Press repeatedly to specify the time (in minutes)
as follows:
Press to start recording while playing
back the track to record.
1
2
3
1
Canceled
Both recording and playback start at the
same time.
When playback ends, recording also stops.
1st generation
Recording from a Disc
or
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can
activate only one of the Daily Timers.
• To correct a misentry during the process, press CANCEL. You
can return to the previous step.
Press repeatedly to select one of the timer
you want to set—TIMER-1, TIMER-2, or
TIMER-3.
Adjust the hour, then the
minute.
R01 00:01
To record the playing track
You can record tracks digitally from a CD onto the USB mass
storage class device.
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
00:00
READ USB
The System uses the Serial Copy Management System which
allows only first-generation digital copies to be made of
premastered software such as regular CDs.
If you try to record from a duplicated disc into the USB mass
storage class device, “SCMS VLT” appears on the display.
2nd generation
1
2
Maintenance
Setting the Daily Timer
Setting the Clock
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press CANCEL.
Press to activate the clock
setting mode.
ALL REC
Unable to record into the USB device.
\ The capacity of the USB device is full. Erase some tracks.
\ You have recorded 999 tracks or groups on the USB mass
storage class device. Erase unwanted tracks.
\ The USB mass storage class device is write-protected.
\ The USB mass storage class device you connected is
incompatible to this System.
7
Press to start recording.
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic,
musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Hyper Bass Sound and Sound Turbo (see page 3) do not
affect recordings.
• You can record up to 999 tracks per group to the USB
mass storage class device. If you try to record a track after
recording 999 tracks, “FILEFULL” appears on the display
and the track will not be recorded.
• The tracks which are recorded to the USB mass storage
class device will be converted into MP3 format (bit rate:
128 kbps).
• You cannot start recording into a USB mass storage class
device while “READING” is shown on the display.
• Do not disconnect a USB mass storage class device while
playing or recording. It may cause malfunction.
• During recording, the Random Play and Repeat Play will be
cancelled.
Recording and Editing Operations
A.STBY (Auto Standby) SLEEP indicator
indicator (See page 6.) (See page 6.)
5
Before You Start recording
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.
Timer mode indicators
(See page 6.)
File type indicators
(See page 4.)
Recording Operations
Radio Operations
DEL NO:
or
To turn on the Daily Timer again, select one of the timer
settings by pressing TIMER, then press SET.
Cancel erasure.
DEL YES: Continue erasure.
6
6
8
LVT1988-001A EN_UX-GN5[B]
MICRO COMPONENT SYSTEM
UX-GN6
—Consists of CA-UXGN6 and SP-UXGN5
Thank you for purchasing a JVC product.
INSTRUCTIONS
LVT1989-004B[B]
0309RYMMDWDAT
©2009 Victor Company of Japan, Limited
Warnings, Cautions and Others
CAUTION
The
button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Dear Customer,
This apparatus is in conformance with the valid European
directives and standards regarding electromagnetic
compatibility and electrical safety.
European representative of Victor Company of Japan,
Limited is:
JVC Technical Services Europe GmbH
Postfach 10 05 04
61145 Friedberg
Germany
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If
the plug fitted is not suitable for the power points in your
home or the cable is too short to reach a power point,
then obtain an appropriate safety approved extension lead
or consult your dealer.
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue:
Neutral
Brown:
Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed
as follows:
The wire which is coloured blue must be connected to
the terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
Products
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION:
Excessive sound pressure from earphones or headphones
can cause hearing loss.
CAUTION:
Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in
the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Side view
CA-UXGN6
SP-UXGN5
SP-UXGN5
Battery
Notice:
The sign Pb
below the
symbol for
batteries
indicates that
this battery
contains lead.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove
the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near
a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
• Do not block the vents.
Front view
Information for Users on Disposal of Old Equipment
and Batteries
CA-UXGN6
[European Union]
These symbols indicate that the electrical
and electronic equipment and the battery
with this symbol should not be disposed
of as general household waste at its endof-life. Instead, the products should be
handed over to the applicable collection
points for the recycling of electrical and
electronic equipment as well as batteries
for proper treatment, recovery and
recycling in accordance with your national
legislation and the Directive 2002/96/EC
and 2006/66/EC.
By disposing of these products correctly,
you will help to conserve natural resources
and will help to prevent potential negative
effects on the environment and human
health which could otherwise be caused
by inappropriate waste handling of these
products.
For more information about collection
points and recycling of these products,
please contact your local municipal office,
your household waste disposal service
or the shop where you purchased the
product.
Penalties may be applicable for incorrect
disposal of this waste, in accordance with
national legislation.
[Business users]
If you wish to dispose of this product,
please visit our web page
http://www.jvc.eu/ to obtain information
about the take-back of the product.
[Other Countries outside the European
Union]
These symbols are only valid in the
European Union.
If you wish to dispose of these items,
please do so in accordance with applicable
national legislation or other rules in your
country for the treatment of old electrical
and electronic equipment and batteries.
Supplied Accessories
Remote sensor
STANDBY lamp
Point at the remote sensor on the front panel.
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
See “Listening to an iPod/Viewing Images on the iPod”
on page 5.
Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as
the source.
• See “Listening to FM and AM Broadcasts” on page 5 or
“Listening to Other Equipment” on page 7.
Adjust the volume
—
Drop the volume in
a moment
PHONES jack
Headphones
(not supplied)
Stereo mini plug cord
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
To use 4/¢
To use VOL +/–
To restore the volume, press again, or adjust the
volume level.
—
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
Select the Sound
Mode
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not work.
Touch to turn on the System.
—
(canceled)
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
The S.TURBO indicator lights up.
To cancel this function, press again.
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Press repeatedly when the System is turned on.
—
Change the display
brightness
Press repeatedly while the System is on standby.
Clock
NOTE:
1
3
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
Playing Back a Disc/USB Mass Storage Class Device
Connections
Do not connect the AC power cord until all other connections have been made.
For iPod
To a wall outlet
Plug the AC power cord only after all
connections are complete.
To connect the monitor
(not supplied)
—To view video/picture
from the iPod
Video cord
(supplied)
Monitor
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Rear view
Touch to open the disc tray.
1
2
Basic Disc/USB Mass Storage Class Device Operations
To
Play back the disc
Press
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
Prepare the Remote Control
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Select a track
Indication/Result
• During playback, press again to pause.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Press and hold
Select a group
(MP3/WMA only)
Insulation sheet
Select the next groups.
Select the previous groups.
To Replace the Battery in the Remote Control
Release
Insert
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
Red
USB cable (not
supplied)
Red
USB memory
(not supplied)
Change
the display
information
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
(only for USB)
Press repeatedly.
NOTES:
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
Black
From right
speaker
Black
To assemble the AM loop antenna (supplied)
NOTES:
Turn the AM loop antenna until
the best reception is obtained.
2
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
NOTES:
To connect the AM loop antenna
AM loop antenna
(supplied)
or
From left
speaker
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
Programming the Playing Order—Program Play
(only for Disc)
1
Select disc as the source.
2
Activate the Program Play.
3
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
or
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m.
• USB mass storage class device is charged through the USB REC/PLAY terminal when
the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB REC/PLAY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB REC/PLAY terminal
may not be fully inserted into the USB REC/PLAY terminal on the System. In such a
case, use a USB extension cable (not supplied) to connect.
5
6
• To check the programmed contents, press 4 or ¢.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from Program Play, press 7.
– The stored program is kept.
Playing at Random—Random Play (only for Disc)
1
Select disc as the source.
2
Press repeatedly to select the desired Random Mode.
RND ALL:
RND GRP:
Press repeatedly to specify the repeat mode as follows:
RPT TRK:
RPT GRP:
RPT ALL:
RPT OFF:
2
Repeats the current (or specified) track. [ 1]
Repeats all tracks in the current group (MP3/WMA
only). [ ]
Repeats all tracks. [ ALL ]
Normal playback
Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
The program is completed and the tracks are
played back in the programmed order.
Operations for Program Play (while not playing)
Playing Repeatedly—Repeat Play
1
Press to store the selected track.
4
Touch to close the disc tray.
3
Lithium coin battery
(product number: CR2025)
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Indication/Result
Remote
DISP OFF: Turns off the display with the motion sensor
on.
ECO ON: Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
When you use the remote control for the first time, pull out
the insulation sheet.
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Main
unit
Turn off the display
while on standby
To connect the speaker cords
NOTES:
Press
To
(canceled)
Getting Started
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN6R (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
• Video cord (× 1)
If anything is missing, consult your dealer immediately.
The operations on pages 4 to 7 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
Basic and Common Operations
3
Plays all tracks in random order. [ALL RND ]
Plays tracks in the current group in random
order. (MP3/WMA only). [RND ]
RND OFF:
Normal playback
Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
or
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same procedure.
4
LVT1989-004B EN_UX-GN6[B] ff
Listening to an iPod/Viewing Images on the iPod
Connecting an iPod
Listening to FM and AM Broadcasts
Basic iPod Operations
Insert the iPod directly to the connector pins.
Protective cap
Direct dock for iPod
To
Play back an
iPod
Press
Connector pins
Forward
search/
Reverse
search
• Be sure to reduce the volume on the System to the
minimum level before connecting an iPod. Adjust the
volume after starting playback.
• DO NOT connect or disconnect the iPod when the System
is turned on.
• You cannot send any data to your iPod from the System.
• Do not carry the System with iPod connected. You might
drop the iPod or it might cause damages to the iPod dock.
• Do not touch or hit the iPod terminal pins or connector
pins in the iPod dock directly. It might cause damages to
the connector part.
• Before viewing a video/picture from your iPod on your
monitor, make the appropriate video setting on the iPod.
For details of the setting, refer to the instruction manual for
the iPod.
Display the
menu/Go
back to the
previous
menu
Select an
item on the
menu
Tune in to a
preset station
• For
presetting
stations, see
the right
column.
Change the
FM reception
mode
(When an
FM stereo
broadcast
is hard to
receive)
• The UP/DOWN
buttons work in
the same way
as operating the
click wheel of iPod
counterclockwise/
clockwise. (Refer
to the instruction
manual for the
iPod for details.)
• Refer to the
instruction manual
for the iPod for
details.
• Refer to the
instruction manual
for the iPod for
details.
Press repeatedly.
Play back at
random
Play back
repeatedly
Change
the display
information
Indication/Result
Press repeatedly to select
“FM” or “AM.”
• The selected frequency
band appears.
Press and hold for more than
2 seconds.
The System starts searching
for stations and stops when
a station of sufficient signal
strength is tuned in.
• Press during searching to
stop.
• Press repeatedly to change
the frequency step by step.
Press repeatedly to select its
preset number.
or
—
or
Press
Select a
frequency
To go back to the
beginning of the
current or previous
tracks.
Press and hold
to fast-forward
the track during
playback.
Press and hold to
fast-reverse the track
during playback.
Dock adapter (supplied with
the iPod or sold separately)
To detach the dock adapter from the dock:
Pull up the dock adapter with your fingernail or sharp
pointed tool using the slot.
• Be careful not to injure your fingertips or damage the
terminal of the dock.
To
Select FM or
AM
Indication/Result
The System detects
the iPod and starts
playback.
Select the next
tracks.
Select a track
Apple iPod (separately
purchased)
Basic Tuner Operations
Receiving FM Stations with Radio Data
System
If you want to know more about Radio Data System, visit <http://
www.rds.org.uk>.
Changing the Radio Data System
Information
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry
mode.
• Finish the following steps while the
indication on the display is flashing.
Press to select a preset number for the
station you want to store.
1
2
Frequency
(No Radio Data System signal)
If no Radio Data System signals are sent by a station, “NO PS,”
“NO PTY,” or “NO RT” appears.
Searching for Programs by PTY Codes
(PTY Search)
You can locate a particular kind of program from the preset
stations (see the left column) by specifying the PTY codes.
Press to enter the PTY code setting
mode.
The PTY code and “SELECT” appear
alternately.
Select a PTY code.
Press to store the station.
Digital Audio Player, etc.
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
1
Turn the volume to minimum.
2
Press repeatedly to select “AUDIO IN.”
3
4
Start playing the connected equipment.
Adjust the volume.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO
IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the
volume level).
Press repeatedly to select the level as follows:
1
NORMAL:
HIGH:
Ordinary input level.
Increases the input level.
2
or
The System searches for 30 preset FM
stations, stops when it finds the one
you have selected, and tunes in to that
station.
3
4
Basic and Common Operations (see page 3)
NOTE:
3
or
Learning More about This System
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from the
one you have intended while recording. If a folder (group)
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management)
Display Information
S.TURBO (Sound Turbo)
indicator (See page 3.)
• To stop searching, press PTY SEARCH.
• To continue searching after it stops on an unwanted
station, press PTY SEARCH while the indications on the
display are flashing.
About SCMS (Serial Copy Management System)
The System uses the Serial Copy Management System which
allows only first-generation digital copies to be made of
premastered software such as regular CDs.
If you try to record from a duplicated disc into the USB mass
storage class device, “SCMS VLT” appears on the display.
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press MENU/CANCEL.
Press to activate the clock
setting mode.
1
00:00
READ USB
2
or
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can
activate only one of the Daily Timers.
• To correct a misentry during the process, press MENU/
CANCEL. You can return to the previous step.
Press repeatedly to select one
of the timer you want to set—
TIMER-1, TIMER-2, or TIMER-3.
1
Adjust the hour, then the
minute.
R01 00:01
Canceled
2
Both recording and playback start at the
same time.
When playback ends, recording also stops.
3
• If you have programmed the playing order for CD (see
“Programming the Playing Order—Program Play” on page
4), the tracks are recorded in the programmed order if
Program Play is activated.
• To stop recording manually, press 7.
Setting the Sleep Timer
Press repeatedly to specify the time (in minutes)
as follows:
To record the playing track
or
(canceled)
The SLEEP indicator lights up and the display
dims.
Press to start recording while playing back the
track to record.
To check the remaining time until the System shuts off,
press SLEEP once.
To erase tracks/groups
1st generation
2nd generation
You can erase tracks/groups on the USB mass storage class
device.
• Once the tracks are erased, you cannot recover them.
• To quit erasing, press 7.
Select a track/group you want to erase while playback
is stopped. (See page 4.)
1
2
3
or
Recording from a Disc
You can record tracks digitally from a CD onto the USB mass
storage class device.
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB/
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3 minutes, the
System turns off.
To cancel this function, press the button again.
4
5
4
iPod)
Select the target to erase.
TTL DEL: Delete a track.
GRP DEL: Delete a group.
DEL ALL: Delete all tracks.
1 Adjust the hour then the
minute for on-time.
2 Adjust the hour then the
minute for off-time.
3 Select the playback source—
“DISC,” “USB HOST,” “TUNER
FM,” “TUNER AM,” “AUDIO IN,”
or “IPOD.”
4 For “TUNER FM” or “TUNER
AM”: Select a preset channel.*
For “DISC” or “USB HOST”:
Select a track. (For MP3/WMA:
Select the group, then the
track number.)
5 Select the volume.
Turn off the System (on standby).
• When the on-time comes,
the System starts playing the
specified source and sets the
volume gradually to the preset
level.
* If no preset channel is stored, “NOMEMORY” appears. When the
on time comes, the System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
To Turn Off the Daily Timer
1
Press repeatedly to select “TIMER-1,”
“TIMER-2,” or “TIMER-3.”
2
DEL NO:
or
Cancel erasure.
To turn on the Daily Timer again, select one of the timer
settings by pressing TIMER, then press SET.
DEL YES: Continue erasure.
6
–
–
–
• If incompatible iPod is connected, the iPod may not be
operated from the System.
• When an iPod is connected to the System, the battery in
the iPod is charged through the iPod terminal (except
when the ECO Mode is activated).
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion occurs,
it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction
manual.
SOUND indicator
(See page 3.)
HBS indicator
(See page 3.)
File type indicators (See page 4.)
Main display
Troubleshooting
Setting the Daily Timer
Setting the Clock
Press to start recording.
ALL REC
–
To get the best performance of the System, keep your discs
and mechanism clean.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
Source indicators
A.STBY (Auto Standby)
indicator (See page 6.)
SLEEP indicator (See page 6.)
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Specifications
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
iPod Operations
Amplifier section
The iPod does not play, but “CONNECT” appears on the
display.
\ The iPod battery is low or exhausted. Charge the iPod
battery.
The video/picture from the iPod is not displayed on the
monitor.
\ The video settings on the iPod is incorrect. Refer to the
instruction manual for the iPod.
OUTPUT POWER:
60 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no
more than 10% total harmonic distortion
Speakers/Impedance:
8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/50 kΩ (at “NORMAL”)
250 mV/50 kΩ (at “HIGH”)
Digital input:
USB REC/PLAY
This equipment has been designed and manufactured
to meet international safety standards but, like any
electrical equipment, care must be taken if you are to
obtain the best results and safety is to be assured.
Tuner section
Radio Operations
FM tuning range:
AM tuning range:
Do ensure that all electrical connections (including
the mains plug, extension leads and interconnections
between pieces of equipment) are properly made and
in accordance with the manufacturer’s instructions.
Switch off and withdraw the mains plug when making
or changing connections.
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise. If
this happens, turn off and on the System again.
87.50 MHz - 108.00 MHz
522 kHz - 1 629 kHz
Disc player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
Recording Operations
USB storage
Unable to record into the USB device.
\ The capacity of the USB device is full. Erase some tracks.
\ You have recorded 999 tracks or groups on the USB mass
storage class device. Erase unwanted tracks.
\ The USB mass storage class device is write-protected.
\ The USB mass storage class device you connected is
incompatible to this System.
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
80 dB
85 dB
Immeasurable
Compatible with USB 2.0 Full Speed
Mass storage class
FAT16, FAT32
DC 5 V
500 mA
iPod section
iPod output power:
VIDEO OUT:
Display Messages for Recording Operations
NODEVICE
• No USB mass storage class device is connected or
the connected USB mass storage class device is not
compatible with this System.
D. (data) FULL
• The capacity of the USB mass storage class device is full.
FILEFULL
• The USB mass storage class device has exceeded the
maximum number of files it can support.
W. (write) PROT
• The USB mass storage class device is write-protected.
SCMS VLT (violation)
• You have tried to copy from a duplicated disc to the USB
mass storage class device.
D. (device) FAIL
• The System failed to read the USB mass storage class
device.
DC 5 V
500 mA
Composite
General
Power requirements:
Power consumption:
Dimensions (approx.):
AC 230 V
, 50 Hz
36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
165 mm x 250 mm x 272 mm
(W x H x D)
3.5 kg
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
ABOVE ALL
– NEVER let anyone, especially children, push anything
into holes, slots or any other opening in the case
Speaker units:
Impedance:
Dimensions (approx.):
Mass (approx.):
4 cm cone x 1
12 cm cone x 1
8Ω
140 mm x 250 mm x 183 mm
(W x H x D)
1.8 kg each
Specifications and appearance are subject to change without
prior notice.
8
DON’T continue to operate the equipment if you are in
any doubt about it working normally, or if it is damaged
in any way—switch off, withdraw the mains plug and
consult your dealer.
DON’T remove any fixed cover as this may expose
dangerous voltages.
DON’T leave equipment switched on when it is
unattended unless it is specifically stated that it is designed
for unattended operation or has a standby mode.
Switch off using the switch on the equipment and make
sure that your family know how to do this.
Special arrangements may need to be made for infirm
or handicapped people.
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
Speakers
Daily Timer does not work.
\ The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
Do consult your dealer if you are ever in doubt about
the installation, operation or safety of your equipment.
DON’T use equipment such as personal stereos or
radios so that you are distracted from the requirements
of traffic safety. It is illegal to watch television whilst
driving.
DON’T listen to headphones at high volume as such use
can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for
example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of
the equipment.
DON’T use makeshift stands and NEVER fix legs with
wood screws—to ensure complete safety always fit the
manufacturer’s approved stand or legs with the fixings
provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain
or moisture.
Mass (approx.):
Timer Operations
Do read the operating instructions before you attempt
to use the equipment.
Do be careful with glass panels or doors on equipment.
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
6
Maintenance
7
Setting the Clock and Using Timers
(On the System)
Audio Video
–
FM reception indicators
(See page 5.)
Timer mode indicators
(See page 6.)
5
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic,
musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Hyper Bass Sound and Sound Turbo (see page 3) do not
affect recordings.
• You can record up to 999 tracks per group to the USB
mass storage class device. If you try to record a track after
recording 999 tracks, “FILEFULL” appears on the display
and the track will not be recorded.
• The tracks which are recorded to the USB mass storage
class device will be converted into MP3 format (bit rate:
128 kbps).
• You cannot start recording into a USB mass storage class
device while “READING” is shown on the display.
• Do not disconnect a USB mass storage class device while
playing or recording. It may cause malfunction.
• During recording, the Random Play and Repeat Play will be
cancelled.
iPod model
iPod nano 1GB/2GB/4GB
iPod nano (2nd Generation)
2GB/4GB/8GB
iPod nano (3rd Generation) 4GB/8GB
iPod nano (4th Generation) 8GB/16GB
iPod mini 4GB/6GB
iPod mini (2nd Generation) 4GB/6GB
iPod (4th Generation) 20GB/40GB
iPod classic 80GB/160GB
iPod photo (4th Generation)
20GB/30GB/40GB/60GB
iPod video (5th Generation)
30GB/60GB/80GB
iPod touch 8GB/16GB
iPod touch (2nd Generation) 8GB/
16GB
Source indicators
REC indicator
If no program is found, “NOTFOUND” appears.
Recording Operations
Listening to an iPod/Viewing Images on the iPod (see
page 5)
• Compatible iPod:
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Play mode indicators
(See page 4.)
NOTE:
Before You Start recording
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a
USB mass storage class device.
• Prohibiting disc ejection (or canceling it) is not available
when the display is turned off (“DISP OFF”) or the ECO
Mode is activated (“ECO ON”) (see page 3).
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
Playing Back a Disc/USB Mass Storage Class Device
NOTE:
Each time you press the button, the information
changes as follows:
Presetting Stations
Front view
Radio Data System allows FM stations to send an additional
signal along with their regular program signals.
With the System, you can receive the following types of Radio
Data System signals.
PS (Program Service):
Shows commonly known
station names.
PTY (Program Type):
Shows types of broadcast
programs.
RT (Radio Text):
Shows text messages the
station sends.
or
Press to improve reception.
The (mono) indicator
lights up.
Stereo effect will be lost.
To restore the stereo effect,
press again. The (stereo)
indicator lights up.
Listening to Other
Equipment
—this could result in a fatal electrical shock.
– NEVER guess or take chances with electrical
equipment of any kind—it is better to be safe than
sorry!
LVT1989-004A EN_UX-GN6[B] f
MICRO COMPONENT SYSTEM
UX-GN5
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in
the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Front view
—Consists of CA-UXGN5 and SP-UXGN5
SP-UXGN5
CAUTION:
Excessive sound pressure from earphones or headphones
can cause hearing loss.
SP-UXGN5
CA-UXGN5
CAUTION:
Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
Side view
Thank you for purchasing a JVC product.
INSTRUCTIONS
CA-UXGN5
LVT1988-015B[UB,UW]
0209RYMMDWDAT
©2009 Victor Company of Japan, Limited
Warnings, Cautions and Others
CAUTION
The
button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
[European Union only]
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove
the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near
a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
• Do not block the vents.
The operations on pages 4 to 6 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
Basic and Common Operations
Remote sensor
STANDBY lamp
Press
Point at the remote sensor on the front panel.
To
Main
unit
Indication/Result
Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
Press repeatedly to select “FM” or “AM” as the source.
• See “Listening to FM and AM Broadcasts” on page 5.
See “Listening to Other Equipment” on page 5.
Adjust the volume
—
Drop the volume in
a moment
PHONES jack
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
To use 4/¢
To use VOL +/–
Select the Sound
Mode
Headphones
(not supplied)
Stereo mini plug cord
To restore the volume, press again, or adjust the
volume level.
—
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
—
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not
work.
Touch to turn on the System.
(canceled)
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
The S.TURBO indicator lights up.
To cancel this function, press again.
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Press repeatedly when the System is turned on.
—
Change the display
brightness
(canceled)
Turn off the display
while on standby
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Press repeatedly while the System is on standby.
Clock
DISP OFF: Turns off the display with the motion sensor
on.
ECO ON: Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
1
3
Getting Started
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN5U (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
• AC plug adapter (× 1) (not supplied for Hong Kong)
If anything is missing, consult your dealer immediately.
Playing Back a Disc/USB Mass Storage Class Device
Connections
Do not connect the AC power cord until all other connections have been made.
To a wall outlet
Plug the AC power cord only after all connections are complete.
• If the wall outlet does not match the AC plug, use the supplied AC
plug adapter (not applicable for Hong Kong).
Rear view
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Touch to open the disc tray.
1
2
Prepare the Remote Control
When you use the remote control for the first time, pull out
the insulation sheet.
To
Play back the disc
Press
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
To connect the speaker cords
Basic Disc/USB Mass Storage Class Device Operations
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Select a track
Select a group
(MP3/WMA only)
Insulation sheet
Lithium coin battery
(product number: CR2025)
Insert
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
Red
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector.
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
Black
From right
speaker
Red
Black
USB cable (not
supplied)
USB memory
(not supplied)
or
From left
speaker
Change
the display
information
To assemble the AM loop antenna (supplied)
To connect the AM loop antenna
AM loop antenna
(supplied)
Turn AM loop antenna until
the best reception is obtained.
2
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than 1 m.
• USB mass storage class device is charged through the USB REC/PLAY terminal when
the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB REC/PLAY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB terminal may not
be fully inserted into the USB REC/PLAY terminal on the System. In such a case, use a
USB extension cable (not supplied) to connect.
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
(only for USB)
Press repeatedly.
(only for Disc)
1
Select disc as the source.
2
Activate the Program Play.
3
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
or
Press to store the selected track.
4
5
6
Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
The program is completed and the tracks are
played back in the programmed order.
Operations for Program Play (while not playing)
• To check the programmed contents, press 4 or ¢.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from Program Play, press 7.
– The stored program is kept.
Playing at Random—Random Play (only for Disc)
NOTES:
1
Select disc as the source.
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
2
Press repeatedly to select the desired Random Mode.
RND ALL:
RND GRP:
Playing Repeatedly—Repeat Play
NOTES:
NOTES:
Select the next groups.
Select the previous groups.
Touch to close the disc tray.
3
Release
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
To go back to the beginning of the current or
previous tracks.
Press and hold
To Replace the Battery in the Remote Control
Indication/Result
• During playback, press again to pause.
Programming the Playing Order—Program Play
1
Press repeatedly to specify the repeat mode as follows:
RPT TRK:
RPT GRP:
RPT ALL:
RPT OFF:
2
Repeats the current (or specified) track. [ 1]
Repeats all tracks in the current group (MP3/WMA
only). [ ]
Repeats all tracks. [ ALL ]
Normal playback
3
Plays all tracks in random order. [ALL RND ]
Plays tracks in the current group in random
order. (MP3/WMA only). [RND ]
RND OFF:
Normal playback
Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
or
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same
procedure.
4
LVT1988-015B EN_UX-GN5[UBUW]ff
Learning More about This System
Listening to Other Equipment
Listening to FM and AM Broadcasts
Selecting AM Tuner Interval Spacing
(on the System only)
Some countries space AM stations 9 kHz apart, and other countries use 10 kHz spacing. Before operating the tuner, select the
appropriate AM tuner interval spacing used for your area.
• You cannot change the AM tuner interval spacing while the ECO (Ecology) Mode is activated.
Select AM as the source.
Basic and Common Operations (see page 3)
Front view
Digital Audio Player, etc.
1
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
Playing Back a Disc/USB Mass Storage Class Device
2
Turn off (standby) the System.
3
Press and hold to change the AM tuner interval spacing.
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
Basic Tuner Operations
To
Select FM or AM
Press
Indication/Result
Press repeatedly.
• The selected frequency band appears.
Select a frequency
Press and hold for more than 2 seconds.
The System starts searching for stations and stops when a station of
sufficient signal strength is tuned in.
• Press during searching to stop.
• Press repeatedly to change the frequency step by step.
or
Tune in to a preset station
• For presetting stations, see
below.
1
Turn the volume to minimum.
2
Press to select “AUDIO IN.”
3
4
Press repeatedly to select its preset number.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO
IN jack is too loud or too quiet, you can change the audio
input level through the AUDIO IN jack (without changing the
volume level).
Press repeatedly to select the level as follows:
Start playing the connected equipment.
NORMAL:
HIGH:
Adjust the volume.
Ordinary input level.
Increases the input level.
or
Change the FM reception
mode
(When an FM stereo
broadcast is hard to receive)
Press to improve reception.
The (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again. The
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
(group) does not include MP3/WMA tracks, they are
ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management).
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
• Prohibiting disc ejection (or canceling it) is not available
when the display is turned off (“DISP OFF”) or the ECO Mode
is activated (“ECO ON”) (see page 3).
Display Information
Play mode indicators (See page 4.)
Source indicator
HBS indicator (See page 3.)
S.TURBO (Sound Turbo)
indicator (See page 3.)
SOUND indicator
(See page 3.)
Source indicators
FM reception indicators
(See page 5.)
REC indicator
(See page 6.)
Timer mode indicators
(See page 6.)
File type indicators
(See page 4.)
Main display
A.STBY (Auto Standby) SLEEP indicator
indicator (See page 6.) (See page 6.)
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
(stereo) indicator lights up.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry mode.
• Finish the following steps while the indication on the display is flashing.
1
2
Press to select a preset number for the station you want to store.
3
or
Press to store the station.
4
5
Recording Operations
7
Setting the Clock and Using Timers
Before You Start recording
About SCMS (Serial Copy Management System)
(On the System)
00:00
2
or
2
• If you have programmed the playing order for CD (see
“Programming the Playing Order—Program Play” on page
4), the tracks are recorded in the programmed order if
Program Play is activated.
• To stop recording manually, press 7.
Setting the Sleep Timer
The SLEEP indicator lights up and the display
dims.
To check the remaining time until the System shuts off,
press SLEEP once.
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB)
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3 minutes,
the System turns off.
Select the target to erase.
TTL DEL: Delete a track.
GRP DEL: Delete a group.
DEL ALL: Delete all tracks.
To cancel this function, press the button again.
4
1 Adjust the hour then the minute for
on-time.
2 Adjust the hour then the minute for
off-time.
3 Select the playback source—“TUNER
FM,” “TUNER AM,” “AUDIO IN,” “DISC,” or
“USB HOST.”
4 For “TUNER FM” or “TUNER AM”:
Select a preset channel.*
For “DISC” or “USB HOST”: Select a
track. (For MP3/WMA: Select the group,
then the track number.)
5 Select the volume.
Turn off the System (on standby).
• When the on-time comes, the System
starts playing the specified source and
sets the volume gradually to the preset
level.
* If no preset channel is stored, “NOMEMORY” appears. When the
on time comes, the System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
To Turn Off the Daily Timer
1
Press repeatedly to select “TIMER-1,”
“TIMER-2,” or “TIMER-3.”
2
4
5
or
(canceled)
You can erase tracks/groups on the USB mass storage class
device.
• Once the tracks are erased, you cannot recover them.
• To quit erasing, press 7.
Select a track/group you want to erase while playback
is stopped. (See page 4.)
or
3
Press repeatedly to specify the time (in minutes)
as follows:
Press to start recording while playing
back the track to record.
1
2
3
1
Canceled
Both recording and playback start at the
same time.
When playback ends, recording also stops.
To erase tracks/groups
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can
activate only one of the Daily Timers.
• To correct a misentry during the process, press CANCEL. You
can return to the previous step.
Press repeatedly to select one of the timer
you want to set—TIMER-1, TIMER-2, or
TIMER-3.
Adjust the hour, then the
minute.
R01 00:01
1st generation
You can record tracks digitally from a CD onto the USB mass
storage class device.
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
1
READ USB
To record the playing track
Recording from a Disc
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press CANCEL.
Press to activate the clock
setting mode.
ALL REC
The System uses the Serial Copy Management System which
allows only first-generation digital copies to be made of
premastered software such as regular CDs.
If you try to record from a duplicated disc into the USB mass
storage class device, “SCMS VLT” appears on the display.
2nd generation
Setting the Daily Timer
Setting the Clock
Press to start recording.
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic,
musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Hyper Bass Sound and Sound Turbo (see page 3) do not
affect recordings.
• You can record up to 999 tracks per group to the USB
mass storage class device. If you try to record a track after
recording 999 tracks, “FILEFULL” appears on the display
and the track will not be recorded.
• The tracks which are recorded to the USB mass storage
class device will be converted into MP3 format (bit rate:
128 kbps).
• You cannot start recording into a USB mass storage class
device while “READING” is shown on the display.
• Do not disconnect a USB mass storage class device while
playing or recording. It may cause malfunction.
• During recording, the Random Play and Repeat Play will be
cancelled.
Troubleshooting
DEL NO:
or
To turn on the Daily Timer again, select one of the timer
settings by pressing TIMER, then press SET.
Cancel erasure.
DEL YES: Continue erasure.
6
6
If you are having a problem with your System, check this list
for a possible solution before calling for service.
General
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Maintenance
To get the best performance of the System, keep your discs
and mechanism clean.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise. If
this happens, turn off and on the System again.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the
disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
Recording and Editing Operations
Unable to record into the USB device.
\ The capacity of the USB device is full. Erase some tracks.
\ You have recorded 999 tracks or groups on the USB mass
storage class device. Erase unwanted tracks.
\ The USB mass storage class device is write-protected.
\ The USB mass storage class device you connected is
incompatible to this System.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
Display Messages for Recording Operations
NODEVICE
• No USB mass storage class device is connected or
the connected USB mass storage class device is not
compatible with this System.
D. (data) FULL
• The capacity of the USB mass storage class device is full.
FILEFULL
• The USB mass storage class device has exceeded the
maximum number of files it can support.
W. (write) PROT
• The USB mass storage class device is write-protected.
SCMS VLT (violation)
• You have tried to copy from a duplicated disc to the USB
mass storage class device.
D. (device) FAIL
• The System failed to read the USB mass storage class
device.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
Specifications
Amplifier section
OUTPUT POWER:
120 W (60 W + 60 W) at 8 Ω (10% THD)
Speakers/Impedance:
8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/47 kΩ (at “NORMAL”)
250 mV/47 kΩ (at “HIGH”)
Digital input:
USB REC/PLAY
Tuner section
FM tuning range:
AM tuning range:
Disc player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
Daily Timer does not work.
\ The System has been turned on when the on-time comes.
Timer starts working only when the System is turned off.
Power requirements:
Power consumption:
AC 110 V – 240 V
, 50 Hz/60 Hz
36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
165 mm x 250 mm x 272 mm
(W x H x D)
3.5 kg
Speakers
Speaker units:
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
Compatible with USB 2.0 Full
Speed
Mass storage class
FAT16, FAT32
DC 5 V
500 mA
General
Mass (approx.):
Timer Operations
80 dB
85 dB
Immeasurable
USB storage
Dimensions (approx.):
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
87.50 MHz – 108.00 MHz
531 kHz – 1 710 kHz (at 9 kHz
spacing)
530 kHz – 1 710 kHz (at 10 kHz
spacing)
Impedance:
Dimensions (approx.):
Mass (approx.):
4 cm cone x 1
12 cm cone x 1
8Ω
140 mm x 250 mm x 183 mm
(W x H x D)
1.8 kg each
Specifications and appearance are subject to change without
prior notice.
8
LVT1988-015B EN_UX-GN5[UBUW]ff
MICRO COMPONENT SYSTEM
UX-GN6
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper or
cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in
the areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an
adequate air path for ventilation by placing on a stand
with a height of 10 cm or more.
Front view
Side view
—Consists of CA-UXGN6 and SP-UXGN5
CAUTION:
Excessive sound pressure from earphones or headphones
can cause hearing loss.
CA-UXGN6
SP-UXGN5
SP-UXGN5
Thank you for purchasing a JVC product.
INSTRUCTIONS
LVT1989-018A[A]
0609RYMMDWDAT
CA-UXGN6
CAUTION:
Battery shall not be exposed to excessive heat such as
sunshine, fire, or the like.
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
[European Union only]
©2009 Victor Company of Japan, Limited
Precautions
Notes on the power cord
• When you are away on travel or otherwise for an extended
period of time, remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always
pull the plug, not the power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or
moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy
on it, which may cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power
cord replaced with a new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove
the plug from the wall outlet, then consult your dealer. Using
the System in this state may cause a fire or electrical shock.
• Do not expose the System to direct sunlight or place it near
a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too
cold—between 5˚C and 35˚C.
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins,
coins, etc. into the System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything
goes wrong, unplug the power cord and consult your
dealer.
Warnings, Cautions and Others
CAUTION
The
button in any position does not disconnect the mains
line.
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off).
The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain readily
operable.
• When the System is on standby, the STANDBY lamp lights
red.
• When the System is turned on, the STANDBY lamp goes
off.
The power can be remote controlled.
The operations on pages 4 to 7 are explained using the remote control, unless mentioned otherwise. However, if the System has the same or similar button names, they can also be
used for the operations.
Basic and Common Operations
Remote sensor
STANDBY lamp
Point at the remote sensor on the front panel.
Press
To
Main
unit
Indication/Result
Remote
Turn on or off
(standby) the power
The STANDBY lamp on the System turns off/on.
Select a source
See “Playing Back a Disc/USB Mass Storage Class Device”
on page 4.
See “Listening to an iPod/Viewing Images on the iPod”
on page 5.
Press repeatedly to select “FM,” “AM,” or “AUDIO IN” as
the source.
• See “Listening to FM and AM Broadcasts” on page 5 or
“Listening to Other Equipment” on page 7.
Adjust the volume
—
Drop the volume in
a moment
PHONES jack
Headphones
(not supplied)
Stereo mini plug cord
Display Demonstration
When you plug in the System, the display demonstration
automatically starts.
To cancel the display demonstration, press and hold DEMO until
“DEMO CLR” is displayed while the System is on standby.
• When the ECO Mode is activated, the display demonstration does
not work (and you cannot deactivate it).
Laser Touch Operation
You can use 4/¢ and VOL +/– on the front panel by sliding
your finger up or down on the illumination.
To use 4/¢
To use VOL +/–
To restore the volume, press again, or adjust the
volume level.
—
Press repeatedly to select the desired Sound Mode.
The SOUND indicator lights up.
Select the Sound
Mode
Using Headphones
Be sure to turn down the volume before connecting or putting on
the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Motion Sensor on the Front Panel
When you move your hand close to the front panel while the System
is on standby, the controls on the front panel illuminate.
• When no operation is done for about 5 seconds, the illumination
turns off.
• When the ECO Mode is activated, the motion sensor does not work.
Touch to turn on the System.
—
(canceled)
Emphasize the
sound (Sound
Turbo)
Reinforce the bass
sound (Hyper Bass
Sound)
The S.TURBO indicator lights up.
To cancel this function, press again.
The HBS indicator lights up.
• When Sound Turbo function is activated (see above),
the HBS indicator goes off and HBS button does not
work.
To cancel this function, press again.
Press repeatedly when the System is turned on.
—
Change the display
brightness
(canceled)
CAUTION:
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Turn off the display
while on standby
Press repeatedly while the System is on standby.
Clock
DISP OFF: Turns off the display with the motion sensor
on.
ECO ON: Turns on the ECO (Ecology) Mode.
ECO Mode reduces power consumption
while the System is on standby by turning
off the display and motion sensor.
NOTE:
1
3
Getting Started
Supplied Accessories
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGN6U (× 1)
• Lithium coin battery (× 1: installed in the remote control)
• AM loop antenna (× 1)
• FM antenna (× 1)
• Video cord (× 1)
If anything is missing, consult your dealer immediately.
Playing Back a Disc/USB Mass Storage Class Device
Connections
Do not connect the AC power cord until all other connections have been made.
For iPod
To a wall outlet
Plug the AC power cord only after all
connections are complete.
To connect the monitor
(not supplied)
—To view video/picture
from the iPod
Video cord
(supplied)
Monitor
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
– USB mass storage class device containing MP3/WMA files.
• When playing back an MP3 or WMA track, corresponding indicator lights up.
Rear view
Touch to open the disc tray.
1
2
Prepare the Remote Control
When you use the remote control for the first time, pull out
the insulation sheet.
Basic Disc/USB Mass Storage Class Device Operations
To
Play back the disc
Press
Play back the USB
mass storage class
device
Stop playback
Loading a Disc (on the System only)
To connect the speaker cords
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Select a track
Select a group
(MP3/WMA only)
Insulation sheet
Select the next groups.
Release
Insert
Forward search/
Reverse search
Connecting a USB Mass Storage Class Device
You can connect a USB mass storage class device such as a USB flash memory
device, MP3 player, multimedia card reader, etc. to the System.
Front view
Red
USB cable (not
supplied)
Red
USB memory
(not supplied)
Change
the display
information
Press and hold to fast-forward the track during
playback.
Press and hold to fast-reverse the track during
playback.
(For MP3/WMA)
Press repeatedly.
NOTES:
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
For better FM reception
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector.
Black
From right
speaker
Black
To assemble the AM loop antenna (supplied)
NOTES:
Turn the AM loop antenna until
the best reception is obtained.
Black
Gray
2
• If no disc is inserted or no USB mass storage class device is connected, “NO DISC” or
“NO USB” appears on the main display.
• If MP3/WMA files are not recorded on the disc or in the USB mass storage class device,
“NO PLAY” appears on the main display.
NOTES:
To connect the AM loop antenna
AM loop antenna
(supplied)
or
From left
speaker
Outdoor FM antenna
(not supplied)
FM antenna (supplied)
• Make sure the antenna conductors do not touch any other
terminals, connecting cords and power cord. Also, keep the
antennas away from metallic parts of the System, connecting
cords, and the AC power cord. This could cause poor reception.
• Keep the AM loop antenna cable wrapped around the AM loop
antenna frame, otherwise the effectiveness and sensitivity of the
AM loop antenna may be reduced.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the
speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch
with the metallic parts of the System.
Programming the Playing Order—Program Play
(only for Disc)
1
Select disc as the source.
2
Activate the Program Play.
3
Select tracks you want for Program Play.
• For MP3/WMA files only: You can also use UP or
DOWN.
or
• When connecting with a USB cable, use the USB 2.0 cable whose length is less than
1 m.
• USB mass storage class device is charged through the USB REC/PLAY terminal when
the System is turned on and the source is “USB.”
• You cannot connect a computer to the USB REC/PLAY terminal of the System.
• Do not disconnect the USB mass storage class device when the System is turned on. It
may cause malfunction of both this System and the device.
• Noise and static electricity may stop the USB mass storage class device sound. In this
case, disconnect the USB mass storage class device and connect it again after turning
off the System.
• Depending on the shape of USB mass storage class device, the USB REC/PLAY terminal
may not be fully inserted into the USB REC/PLAY terminal on the System. In such a
case, use a USB extension cable (not supplied) to connect.
5
6
• To check the programmed contents, press 4 or ¢.
• To erase the entire program, press and hold CANCEL for about 2 seconds.
• To exit from Program Play, press 7.
– The stored program is kept.
Playing at Random—Random Play (only for Disc)
1
Select disc as the source.
2
Press repeatedly to select the desired Random Mode.
RND ALL:
RND GRP:
Press repeatedly to specify the repeat mode as follows:
RPT TRK:
RPT GRP:
RPT ALL:
RPT OFF:
2
Repeats the current (or specified) track. [ 1]
Repeats all tracks in the current group (MP3/WMA
only). [ ]
Repeats all tracks. [ ALL ]
Normal playback
Repeat steps 3 and 4 to program other tracks you want.
• If you try to program a 33rd track, “PGM FULL” appears.
The program is completed and the tracks are
played back in the programmed order.
Operations for Program Play (while not playing)
Playing Repeatedly—Repeat Play
1
Press to store the selected track.
4
Touch to close the disc tray.
3
Lithium coin battery
(product number: CR2025)
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
Select the previous groups.
To Replace the Battery in the Remote Control
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from overheating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
Indication/Result
• During playback, press again to pause.
To go back to the beginning of the current or
previous tracks.
Press and hold
NOTES:
DO NOT turn off (standby) the System with the volume set to an extremely high level; otherwise, the sudden
blast of sound can damage your hearing, speakers and/or headphones when you turn on the System or start
playback.
3
Plays all tracks in random order. [ALL RND ]
Plays tracks in the current group in random
order. (MP3/WMA only). [RND ]
RND OFF:
Normal playback
Playback starts in random order.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
or
Prohibiting Disc Ejection
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
While the System is on standby...
To cancel the prohibition, repeat the same procedure.
4
LVT1989-018A EN_UX-GN6[A] 2
Listening to an iPod/Viewing Images on the iPod
Connecting an iPod
Basic iPod Operations
Insert the iPod directly to the connector pins.
Protective cap
Direct dock for iPod
To
Play back an
iPod
Press
Apple iPod (separately
purchased)
Connector pins
• Be sure to reduce the volume on the System to the
minimum level before connecting an iPod. Adjust the
volume after starting playback.
• DO NOT connect or disconnect the iPod when the System
is turned on.
• You cannot send any data to your iPod from the System.
• Do not carry the System with iPod connected. You might
drop the iPod or it might cause damages to the iPod dock.
• Do not touch or hit the iPod terminal pins or connector
pins in the iPod dock directly. It might cause damages to
the connector part.
• Before viewing a video/picture from your iPod on your
monitor, make the appropriate video setting on the iPod.
For details of the setting, refer to the instruction manual for
the iPod.
(on the System only)
Some countries space AM stations 9 kHz apart, and other
countries use 10 kHz spacing. Before operating the tuner,
select the appropriate AM tuner interval spacing used for
your area.
• You cannot change the AM tuner interval spacing while the
ECO (Ecology) Mode is activated.
Select AM as the source.
1
To go back to the
beginning of the
current or previous
tracks.
Press and hold
to fast-forward
the track during
playback.
Press and hold to
fast-reverse the track
during playback.
Forward
search/
Reverse
search
Dock adapter (supplied with
the iPod or sold separately)
To detach the dock adapter from the dock:
Pull up the dock adapter with your fingernail or sharp
pointed tool using the slot.
• Be careful not to injure your fingertips or damage the
terminal of the dock.
Selecting AM Tuner Interval Spacing
Indication/Result
The System detects
the iPod and starts
playback.
Select the next
tracks.
Select a track
Listening to Other
Equipment
Listening to FM and AM Broadcasts
2
Turn off (standby) the System.
3
Press and hold to change the AM tuner
interval spacing.
Presetting Stations
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry
mode.
• Finish the following steps while the
indication on the display is flashing.
Press to select a preset number for the
station you want to store.
To
Select FM or
AM
—
• The UP/DOWN
buttons work in
the same way
as operating the
click wheel of iPod
counterclockwise/
clockwise. (Refer
to the instruction
manual for the
iPod for details.)
• Refer to the
instruction manual
for the iPod for
details.
• Refer to the
instruction manual
for the iPod for
details.
Press repeatedly.
or
Play back at
random
Play back
repeatedly
Change
the display
information
Press
Select a
frequency
or
Tune in to a
preset station
• For
presetting
stations, see
the right
column.
Change the
FM reception
mode
(When an
FM stereo
broadcast
is hard to
receive)
Digital Audio Player, etc.
1
2
To audio output (or
headphone out, etc.)
Stereo mini plug cord
(not supplied)
or
Press to store the station.
4
1
2
3
4
Indication/Result
Press repeatedly to select
“FM” or “AM.”
• The selected frequency
band appears.
Press and hold for more than
2 seconds.
The System starts searching
for stations and stops when
a station of sufficient signal
strength is tuned in.
• Press during searching to
stop.
• Press repeatedly to change
the frequency step by step.
Press repeatedly to select its
preset number.
Basic and Common Operations (see page 3)
Listening to an iPod/Viewing Images on the iPod (see
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
• You cannot use the Sound Mode and Sound Turbo at the
same time.
page 5)
• Compatible iPod:
iPod model
Audio Video
–
iPod nano 1GB/2GB/4GB
iPod nano (2nd Generation)
–
2GB/4GB/8GB
iPod nano (3rd Generation) 4GB/8GB
iPod nano (4th Generation) 8GB/16GB
iPod mini 4GB/6GB
–
iPod mini (2nd Generation) 4GB/6GB
–
iPod (4th Generation) 20GB/40GB
–
iPod classic 80GB/160GB
iPod photo (4th Generation)
20GB/30GB/40GB/60GB
iPod video (5th Generation)
30GB/60GB/80GB
iPod touch 8GB/16GB
iPod touch (2nd Generation) 8GB/16GB
Playing Back a Disc/USB Mass Storage Class Device
3
Basic Tuner Operations
Display the
menu/Go
back to the
previous
menu
Select an
item on the
menu
Front view
Learning More about This System
Turn the volume to minimum.
Press repeatedly to select “AUDIO IN.”
Start playing the connected equipment.
Adjust the volume.
To Preset the Audio Input Level
If the sound from the equipment connected to the AUDIO
IN jack is too quiet, you can change the audio input level
through the AUDIO IN jack (without changing the volume
level).
Press repeatedly to select the level as follows:
NORMAL:
HIGH:
Ordinary input level.
Increases the input level.
or
Press to improve reception.
The (mono) indicator
lights up.
Stereo effect will be lost.
To restore the stereo effect,
press again. The (stereo)
indicator lights up.
(see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at
a sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at a bit rate of less
than 64 kbps.
– Playback order of MP3/WMA tracks may be different from the
one you have intended while recording. If a folder (group)
does not include MP3/WMA tracks, they are ignored.
• Do not use the following USB mass storage class devices...
– Whose rating is other than 5 V and exceeds 500 mA.
– Equipped with special functions such as data security
functions.
– Divided by 2 or more partitions.
• For the USB mass storage class device playback...
– When connecting a USB mass storage class device, also
refer to its manual.
– Connect one USB mass storage class device to the System
at a time. Do not use a USB hub.
– This System is compatible with USB 2.0 Full Speed.
– You can play back MP3/WMA files in a USB mass storage
class device (maximum data transfer rate: 2 Mbps).
– You cannot play back a file larger than 2 Gigabytes.
– This System may not play back some USB mass storage
class devices and does not support DRM (Digital Rights
Management)
• This System can recognize up to 255 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
• This System can recognize up to 99 groups and 999 tracks
(with a maximum number of 255 tracks in a group) in a USB
mass storage class device.
• Prohibiting disc ejection (or canceling it) is not available
when the display is turned off (“DISP OFF”) or the ECO Mode
is activated (“ECO ON”) (see page 3).
Recording Operations
About SCMS (Serial Copy Management System)
The System uses the Serial Copy Management System which
allows only first-generation digital copies to be made of
premastered software such as regular CDs.
If you try to record from a duplicated disc into the USB
mass storage class device, “CAN NOT COPY” appears on the
display.
1st generation
2nd generation
(On the System)
00:00
2
or
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can
activate only one of the Daily Timers.
• To correct a misentry during the process, press MENU/
CANCEL. You can return to the previous step.
Press repeatedly to select one
of the timer you want to set—
TIMER-1, TIMER-2, or TIMER-3.
1
Adjust the hour, then the
minute.
R01 00:01
Canceled
3
• If you have programmed the playing order for CD (see
“Programming the Playing Order—Program Play” on page
4), the tracks are recorded in the programmed order if
Program Play is activated.
• To stop recording manually, press 7.
Setting the Sleep Timer
Press repeatedly to specify the time (in minutes)
as follows:
To record the playing track
or
(canceled)
The SLEEP indicator lights up and the display
dims.
Press to start recording while playing back the
track to record.
To check the remaining time until the System shuts off,
press SLEEP once.
To erase tracks/groups
You can erase tracks/groups on the USB mass storage class
device.
• Once the tracks are erased, you cannot recover them.
• To quit erasing, press 7.
Select a track/group you want to erase while playback
is stopped. (See page 4.)
Turning Off the System Automatically
—Auto Standby function (only for Disc/USB/
Press to activate the Auto Standby.
• The A.STBY indicator lights up.
• The A.STBY indicator starts flashing after
playback stops.
If no operation is done for about 3 minutes, the
System turns off.
To cancel this function, press the button again.
4
5
4
iPod)
Select the target to erase.
TTL DEL: Delete a track.
GRP DEL: Delete a group.
DEL ALL: Delete all tracks.
1 Adjust the hour then the
minute for on-time.
2 Adjust the hour then the
minute for off-time.
3 Select the playback source—
“DISC,” “USB HOST,” “TUNER
FM,” “TUNER AM,” “AUDIO IN,”
or “IPOD.”
4 For “TUNER FM” or “TUNER
AM”: Select a preset channel.*
For “DISC” or “USB HOST”:
Select a track. (For MP3/WMA:
Select the group, then the
track number.)
5 Select the volume.
Turn off the System (on standby).
• When the on-time comes,
the System starts playing the
specified source and sets the
volume gradually to the preset
level.
* If no preset channel is stored, “NOMEMORY” appears. When the
on time comes, the System tunes in to the station last tuned in.
To exit from the timer setting, press TIMER as required.
To Turn Off the Daily Timer
1
Press repeatedly to select “TIMER-1,”
“TIMER-2,” or “TIMER-3.”
2
DEL NO:
or
Cancel erasure.
To turn on the Daily Timer again, select one of the timer
settings by pressing TIMER, then press SET.
DEL YES: Continue erasure.
6
6
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
Display Information
S.TURBO (Sound Turbo)
indicator (See page 3.)
SOUND indicator
(See page 3.)
HBS indicator
(See page 3.)
Source indicators
Play mode indicators
(See page 4.)
FM reception indicators
(See page 5.)
Timer mode indicators
(See page 6.)
REC indicator
Source indicators
Main display
Troubleshooting
To get the best performance of the System, keep your discs
and mechanism clean.
If you are having a problem with your System, check this list
for a possible solution before calling for service.
Handling discs
• Remove the disc from its case by holding it at the edge
while pressing the center hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when
placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes,
and moisture.
General
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center
to edge.
2
Both recording and playback start at the
same time.
When playback ends, recording also stops.
or
Recording from a Disc
1
READ USB
1
2
3
You can record tracks digitally from a CD onto the USB mass
storage class device.
• Do not vibrate the System while recording tracks. It may
damage the recorded tracks.
Without setting the built-in clock, you cannot use Daily Timer.
• To go back to the previous step, press MENU/CANCEL.
Press to activate the clock
setting mode.
ALL REC
Maintenance
Setting the Daily Timer
Setting the Clock
Press to start recording.
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the consent
of the owner of copyright in the sound or video recording,
broadcast or cable program and in any literary, dramatic,
musical, or artistic work embodied therein.
• The recording level is not affected by the volume.
• Hyper Bass Sound and Sound Turbo (see page 3) do not
affect recordings.
• You can record up to 999 tracks per group to the USB
mass storage class device. If you try to record a track after
recording 999 tracks, “FILEFULL” appears on the display
and the track will not be recorded.
• The tracks which are recorded to the USB mass storage
class device will be converted into MP3 format (bit rate:
128 kbps).
• You cannot start recording into a USB mass storage class
device while “READING” is shown on the display.
• Do not disconnect a USB mass storage class device while
playing or recording. It may cause malfunction.
• During recording, the Random Play and Repeat Play will be
cancelled.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
A.STBY (Auto Standby)
indicator (See page 6.)
SLEEP indicator (See page 6.)
7
Setting the Clock and Using Timers
Before You Start recording
JVC bears no responsibility for any loss of data in USB mass
storage class device while using this System.
• If incompatible iPod is connected, the iPod may not be
operated from the System.
• When an iPod is connected to the System, the battery in
the iPod is charged through the iPod terminal (except
when the ECO Mode is activated).
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion occurs,
it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction
manual.
File type indicators (See page 4.)
5
Setting the Clock and Using Timers (see page 6)
• You cannot set the clock and Daily Timer while the ECO
(Ecology) Mode is activated.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, adjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you activate the Sleep Timer after Daily Timer starts
playing the selected source, Daily Timer is canceled.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is
heavily stained, wipe it with a cloth soaked in water-diluted
neutral detergent and wrung well, then wipe clean with a
dry cloth.
• Since the System may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
following:
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strongly.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides
to it.
– DO NOT allow any rubber or plastic to remain in contact
for a long time.
Specifications
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power cord
and then plug it back in.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
iPod Operations
Amplifier section
The iPod does not play, but “CONNECT” appears on the
display.
\ The iPod battery is low or exhausted. Charge the iPod
battery.
The video/picture from the iPod is not displayed on the
monitor.
\ The video settings on the iPod is incorrect. Refer to the
instruction manual for the iPod.
OUTPUT POWER:
120 W (60 W+60 W) at 8 Ω (10% THD)
Speakers/Impedance:
8 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/50 kΩ (at “NORMAL”)
250 mV/50 kΩ (at “HIGH”)
Digital input:
USB REC/PLAY
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antenna connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.
Recording Operations
Unable to record into the USB device.
\ The capacity of the USB device is full. Erase some tracks.
\ You have recorded 999 tracks or groups on the USB mass
storage class device. Erase unwanted tracks.
\ The USB mass storage class device is write-protected.
\ The USB mass storage class device you connected is
incompatible to this System.
Display Messages for Recording Operations
NODEVICE
• No USB mass storage class device is connected or
the connected USB mass storage class device is not
compatible with this System.
D. (data) FULL
• The capacity of the USB mass storage class device is full.
FILEFULL
• The USB mass storage class device has exceeded the
maximum number of files it can support.
W. (write) PROT
• The USB mass storage class device is write-protected.
CAN NOT COPY
• You have tried to copy from a duplicated disc to the USB
mass storage class device.
D. (device) FAIL
• The System failed to read the USB mass storage class
device.
Disc/USB Mass Storage Class Device Operations
The disc/USB mass storage class device does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The USB mass storage class device is not connected
properly.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
The disc/USB mass storage class device sound is
discontinuous.
\ The disc is scratched or dirty.
\ MP3/WMA files have not been properly copied into the
USB mass storage class device.
Sounds from USB mass storage class device are interrupted.
\ Noise and static electricity may stop the sound. In this
case, disconnect and connect the USB mass storage class
device again after turning off the System.
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
Tuner section
FM tuning range:
AM tuning range:
87.50 MHz - 108.00 MHz
531 kHz – 1 710 kHz (at 9 kHz
spacing)
530 kHz – 1 710 kHz (at 10 kHz
spacing)
Disc player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
80 dB
85 dB
Immeasurable
USB storage
USB specification:
Compatible device:
Compatible file system:
Bus power supply:
Compatible with USB 2.0 Full
Speed
Mass storage class
FAT16, FAT32
DC 5 V
500 mA
iPod section
iPod output power:
VIDEO OUT:
DC 5 V
500 mA
Composite
General
Power requirements:
Power consumption:
Dimensions (approx.):
Mass (approx.):
AC 240 V
, 50 Hz
36 W (power on)
5 W (standby mode)
1 W or less (ECO Mode)
165 mm x 250 mm x 272 mm
(W x H x D)
3.5 kg
Speakers
Speaker units:
Impedance:
Dimensions (approx.):
Mass (approx.):
4 cm cone x 1
12 cm cone x 1
8Ω
140 mm x 250 mm x 183 mm
(W x H x D)
1.8 kg each
Specifications and appearance are subject to change without
prior notice.
8
LVT1989-018A EN_UX-GN6[A] 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising