JVC | 0710DTSMDTJEIN | User's Manual | JVC 0710DTSMDTJEIN User's Manual

JVC 0710DTSMDTJEIN User's Manual
INFORMATION (For U.S.A.)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
KD-S27
CD RECEIVER : INSTRUCTIONS/INSTALLATION
Thank you for purchasing a JVC product.
Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best
possible performance from the unit.
Caution:
For customer Use:
Enter below the Model No. and Serial No. which are located
on the top or bottom of the cabinet. Retain this information
for future reference.
Model No.
Serial No.
Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.
IMPORTANT FOR LASER PRODUCTS
0710DTSMDTJEIN
EN
© 2010 Victor Company of Japan, Limited
GET0698-001A
[J]
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover. There are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: (For U.S.A.) Visible and/or invisible class II laser radiation when open. Do not stare into beam.
(For Canada) Visible and/or invisible class 1M laser radiation when open. Do not view directly
with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED OUTSIDE THE UNIT.
Canceling the display demonstration
1 Turn on the power.
4 Select <DEMO OFF>.
For safety...
2
• Do not raise the volume level too much, as this will
block outside sounds, making driving dangerous.
• Stop the car before performing any complicated
operations.
[European Union only]
5
[Hold]
(Initial setting)
3
6 Finish the procedure.
Setting the clock
Temperature inside the car...
If you need to operate the unit while driving, be sure
to look around carefully or you may be involved in a
traffic accident.
If you have parked the car for a long time in hot or
cold weather, wait until the temperature in the car
becomes normal before operating the unit.
Basic operations
1 Turn on the power.
2
Warning:
5 Adjust the hour.
[Hold]
Ejects the disc
Control dial
Loading slot
Display window
6 Adjust the minute.
(Initial setting)
3 Select <CLOCK>.
Auxiliary input jack
Detaches the panel
7 Finish the procedure.
Returns to the previous menu
4 Select <CLOCK SET>.
Remote sensor
• DO NOT expose to bright sunlight.
Preparations
USB (Universal Serial
Bus) input jack
How to attach/detach the control
panel
If the effectiveness of the remote controller
decreases, replace the battery.
When you press or hold the following button(s)...
Replacing the lithium coin battery
Main unit
CR2025
Remote
controller
Turns on.
• When the power is on, pressing /I/ATT on the remote controller
also attenuates the sound or pauses. Press /I/ATT again to cancel
muting or resume playback.
Turns off if pressed and held.
Selects the available sources (if the power is turned on).
• If the source is ready, playback also starts.
How to reset your unit
Reset the unit after installation is
completed.
• Your preset adjustments will
also be erased.
• You can forcibly eject the loaded disc even if the
disc is locked. To lock/unlock the disc, see page 2.
• Be careful not to drop the disc when it ejects.
• If this does not work, reset your unit.
Preparing the remote controller
(RM-RK50)
When you use the remote controller for the first time,
pull out the insulation sheet.
EN_KD-S27[J]_f.indd 1
Adjusts the volume level.
Caution:
[Hold]
Insulation sheet
For USA-California Only:
This product contains a CR Coin Cell Lithium Battery
which contains Perchlorate Material—special
handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
—
How to forcibly eject a disc
• Danger of explosion if battery is incorrectly
replaced. Replace only with the same or equivalent
type.
• Battery shall not be exposed to excessive heat such
as sunshine, fire, or the like.
Warning (about battery handling)
To prevent accidents and damage:
• Do not install any battery other than CR2025 or its
equivalent.
• Store out of reach of children.
• Do not recharge, short, or dismantle.
• Do not dispose of in fire.
• Do not carry around with other metallic materials.
• Wrap the battery with tape and insulate when
throwing away or saving it.
General operations
—
Selects items.
• Mutes the sound while listening to a source. If the source is “CD” or
“USB,” playback pauses. Press the control dial again to cancel muting
or resume playback.
• Confirms selection.
Selects the sound mode.
• Enters tone level adjustment directly (see page 3) if pressed and held
EQ BASS-TRE on the main unit.
—
Enters playback mode menu directly (see page 2).
—
Power off : Checks the current clock time.
Power on : Changes the display information.
1 – EN
7/1/10 3:43:25 PM
Listening to the radio
~
Ÿ
] “FM” or “AM”
Listening to the disc
~
Ÿ
] Turn on the power.
“ST” lights up when receiving an FM stereo broadcast with
sufficient signal strength.
Manual search
“M” flashes, then press the
button repeatedly.
All tracks will be played repeatedly until you change the source or
eject the disc.
Selecting a preset station
1
Stopping playback and ejecting the disc Selecting the playback modes
“NO DISC” appears.
Press / SOURCE to listen to another
playback source.
[Hold]
or
When an FM stereo broadcast is hard
to receive
1
[Hold]
2
Prohibiting disc ejection
[Hold]
You can assign titles to 30 station frequencies (FM
and AM) using 8 characters (maximum) for each title.
] <TUNER> ] <MONO> ] <MONO ON>
Reception improves, but stereo effect will be
lost.
To restore the stereo effect, repeat the same
procedure to select <MONO OFF>.
Automatic presetting (FM)—
SSM (Strong-station Sequential Memory)
1
1
2
[Hold]
To preset another 6 stations, repeat the above
procedure by selecting one of the other six SSM
setting ranges.
Manual presetting (FM/AM)
You can preset up to 18 stations for FM and 6
stations for AM.
Ex.: Storing FM station of 92.50 MHz into preset
number “04.”
1
] “92.50MHz”
2
[Hold]
“PRESET MODE” flashes.
3
Selects folder of the MP3/
WMA
] Selects a character.
4
Selects track
] Move to the next (or previous) character
position.
Repeat steps 3 and 4 until you finish entering
the title.
6
[Hold]
To erase the entire title, press and hold DISP after
step 2, then press the control dial.
Fast-forwards or reverses
the track
2
B
K
T
2
/
C
L
U
3
<
D
M
V
4
>
E
N
W
5
F
O
X
6
G
P
Y
7
Space
H
Q
Z
8
I
R
0
9
For MP3/WMA discs, select the desired folder, then
the desired track by repeating step 2.
• To return to the previous menu, press BACK.
5 U / D ∞ : Selects folder of the MP3/
WMA
2 R / F 3 : Selects track
2 R / F 3 : Fast-forwards or reverses the
[Hold]
track
Station name * = Frequency =
Clock = (back to the beginning)
* If no title is assigned to a station, “NO NAME” appears
for a few seconds.
Listening to the USB device
Using the remote controller
This unit can play MP3/WMA tracks stored in a USB device.
~
Ÿ
You can connect an external component to the AUX
(auxiliary) input jack on the control panel.
• Make sure <AUX ON> is selected for the
<SRC SELECT> = <AUX IN> setting on page 3.
Portable audio player,
etc.
USB memory
All tracks will be played repeatedly until you change the source or
detach the USB device.
3.5 mm (3/16”) stereo mini
plug (not supplied)
1
USB input jack
] Turn on the power.
Listening to the external components
2
Using the remote controller
Changing the display information
] Selects preset number “04.”
“P04” flashes and “MEMORY” appears.
] “AUX IN”
Turn on the connected component and start
playing the source.
Disc title/Album name/performer (folder name)*
= Track title (file name)* = Current track
number with the elapsed playing time = Current
track number with the clock time = (back to the
beginning)
* If the current disc is an audio CD, “NO NAME” appears.
If an MP3/WMA file does not have Tag information
or <TAG DISPLAY> is set to <TAG OFF> (see page 3),
folder name and file name appear.
Available characters
A
J
S
1
—
To cancel repeat play or random play, select
“RPT OFF” or “RND OFF.”
Changing the display information
Selecting a track/folder
1
5 U / D ∞ : Changes the preset stations
2 R / F 3 : Searches for stations
3
REPEAT
TRACK RPT : Repeats current track
FOLDER RPT : Repeats current folder
RANDOM
FOLDER RND : Randomly plays all tracks of
current folder, then tracks of
next folders
ALL RND
: Randomly plays all tracks
] Show the title entry screen.
5
] <TUNER> ] <SSM> ] <SSM 01 – 06> /
<SSM 07 – 12> / <SSM 13 – 18>
“SSM” flashes and local stations with the
strongest signals are searched and stored
automatically.
3
Discs produce very little noise compared with other
sources. Lower the volume before playing a disc to
avoid damaging the speakers by the sudden increase
of the output level.
[Hold]
2
] “REPEAT” j “RANDOM”
To cancel the prohibition, repeat the same
procedure.
Caution on volume setting:
] “FM” or “AM”
You can preset up to 18 stations for FM.
While listening to a station...
1
2
Assigning title to a station
2
You can use only one of the following playback
modes at a time.
If a USB device has been attached...
Pressing / SOURCE turns on the power and playback
starts from where it has been stopped previously.
• If a different USB device is currently attached,
playback starts from the beginning.
Stopping playback and detaching the
USB device
Straightly pull it out from the unit.
“NO USB” appears. Press / SOURCE to listen to
another playback source.
You can operate the USB device in the same way
you operate the files on a disc.
Caution on volume setting:
USB devices produce very little noise compared with
other sources. Lower the volume before playing
a USB to avoid damaging the speakers by sudden
increase of the output level.
Cautions:
• Avoid using the USB device if it might hinder your
safety driving.
• Do not pull out and attach the USB device
repeatedly while “READING” is shown on the
display.
• Do not start the car engine if a USB device is
connected.
• This unit may not be able to play the files
depending on the type of USB device.
• Operation and power supply may not work as
intended for some USB devices.
• You cannot connect a computer to the USB input
terminal of the unit.
• Make sure all important data has been backed up to
avoid losing the data.
• Do not leave a USB device in the car, expose to
direct sunlight, or high temperature to avoid
deformation or cause damages to the device.
• Some USB devices may not work immediately after
attaching USB device or turn on the power.
• For more details about USB operations, see page 4.
2 – EN
EN_KD-S27[J]_f.indd 2
7/1/10 3:43:28 PM
Selecting a preset sound mode
You can select a preset sound mode suitable for the music genre.
FLAT = NATURAL = DYNAMIC =
VOCAL BOOST = BASS BOOST =
USER = (back to the beginning)
Storing your own sound mode
Tone
You can store your own adjustments in memory.
1
While listening, you can adjust the tone level of the selected sound
mode.
BASS
[Hold]
MIDDLE
2
TREBLE
1
[Hold]
] <PRO EQ> ] <BASS> / <MIDDLE> / <TREBLE>
Frequency
60 Hz, 80 Hz, 100 Hz,
200 Hz
0.5 kHz, 1.0 kHz,
1.5 kHz, 2.5 kHz
10.0 kHz, 12.5 kHz,
15.0 kHz, 17.5 kHz
Sound element
Level
–06 to +06
–06 to +06
–06 to +06
Q
Q1.0, Q1.25,
Q1.5, Q2.0
Q0.75, Q1.0,
Q1.25
Q FIX
3
2
Adjust the level (–06 to +06) of the selected tone (BASS /
MIDDLE / TREBLE).
The sound mode is automatically stored and changed to “USER.”
4
Adjust the sound elements of the selected tone ( see table on
the right).
Repeat steps 2 and 3 to adjust other tones.
The adjustments made will be stored automatically in “USER.”
The current sound mode changes to “USER” automatically.
Menu operations
1
[Hold]
Repeat step 2 if necessary.
• To return to the previous menu, press BACK.
• To exit from the menu, press DISP or MENU.
Category
Selectable setting, [Initial: Underlined]
DEMO
• DEMO ON
CLOCK SET
• DEMO OFF
[ 1:00 ]
: Display demonstration will be activated automatically if
no operation is done for about 20 seconds.
: Cancels.
: Adjust the hour, then the minute.
BASS
MIDDLE
TREBLE
DIMMER
—
: For settings, see “Storing your own sound mode.”
TAG
DISPLAY
SSM *2
TUNER
AREA
MONO *2
IF BAND
• AUTO
• WIDE
AUDIO
• DIMMER ON
: Dims the display and button illumination.
• DIMMER OFF
: Cancels.
• SCROLL ONCE
: Scrolls the displayed information once.
• SCROLL AUTO
: Repeats scrolling (at 5-second intervals).
• SCROLL OFF
: Cancels.
Pressing DISP for more than one second can scroll the display regardless of the
setting.
• TAG ON
: Shows the Tag information while playing MP3/WMA
tracks.
• TAG OFF
: Cancels.
• SSM 01 – 06
: For settings, see “Automatic presetting (FM)—SSM
• SSM 07 – 12
(Strong-station Sequential Memory)” on page 2.
• SSM 13 – 18
• AREA US
: When using in North/Central/South America. AM/FM
intervals are set to 10 kHz/200 kHz.
• AREA EU
: When using in any other areas. AM/FM intervals are set
to 9 kHz/50 kHz (100 kHz during auto search).
• AREA SA
: When using in South American countries where FM
interval is 100 kHz. AM interval is set to 10 kHz.
• MONO ON
: Activate monaural mode to improve FM reception, but
stereo effect will be lost.
: Restore the stereo effect.
• MONO OFF
L/O MODE
SUB.W
LEVEL *5
BEEP
AMP GAIN *6
*1
*2
*3
*4
*5
*6
*7
*8
• SUB.W
• REAR
SUB.W
FREQ *5
: Increases the tuner selectivity to reduce interference
noises between adjacent stations. (Stereo effect may be
lost.)
: Subject to interference noises from adjacent stations,
but sound quality will not be degraded and the stereo
effect will remain.
Selectable setting, [Initial: Underlined]
R06 – F06 [ 00 ]
L06 – R06 [ 00 ]
• LOUD ON
• LOUD OFF
VOL ADJUST VOL ADJ –05 —
VOL ADJ +05
[ VOL ADJ 00 ]
SRC
SELECT
DISPLAY
SCROLL *1
Menu item
FADER *3
BALANCE *4
LOUD
CLOCK DEMO
Menu item
3
PRO EQ
Category
2
AM *7
AUX IN *8
• LOW
• MID
• HIGH
SUB.W 00 —
SUB.W 08
[ SUB.W 04 ]
• BEEP ON
• BEEP OFF
• LOW POWER
• HIGH POWER
• AM ON
• AM OFF
• AUX ON
• AUX OFF
: Adjust the front and rear speaker output balance.
: Adjust the left and right speaker output balance.
: Boost low and high frequencies to produce a wellbalanced sound at a low volume level.
: Cancels.
: Preset the volume adjustment level of each source
(except FM), compared to the FM volume level. The
volume level will automatically increase or decrease when
you change the source.
• Before making an adjustment, select the source you
want to adjust.
• “VOL ADJ FIX” appears on the display if “FM” is selected
as the source.
: Select if the REAR LINE OUT terminals are used for
connecting a subwoofer (through an external amplifier).
: Select if the REAR LINE OUT terminals are used for
connecting the speakers (through an external amplifier).
: Frequencies lower than 72 Hz are sent to the subwoofer.
: Frequencies lower than 111 Hz are sent to the subwoofer.
: Frequencies lower than 157 Hz are sent to the subwoofer.
: Adjust the subwoofer output level.
: Activates the keypress tone.
: Deactivates the keypress tone.
: VOLUME 00 – VOLUME 30 (Select if the maximum power
of each speaker is less than 50 W to prevent damaging the
speakers.)
: VOLUME 00 – VOLUME 50
: Enable “AM” in source selection.
: Disable “AM” in source selection.
: Enable “AUX IN” in source selection.
: Disable “AUX IN” in source selection.
Some characters or symbols will not be shown correctly (or will be blanked) on the display.
Displayed only when the source is “FM.”
If you are using a two-speaker system, set the fader level to “00.”
This adjustment will not affect the subwoofer output.
Displayed only when <L/O MODE> is set to <SUB.W>.
The volume level automatically changes to “VOLUME 30” if you change to <LOW POWER> with the volume level
is set higher than “VOLUME 30.”
Displayed only when any source other than “AM” is selected.
Displayed only when any source other than “AUX IN” is selected.
3 – EN
EN_KD-S27[J]_f.indd 3
7/1/10 3:43:29 PM
More about this unit
Troubleshooting
Symptom
General
Sound cannot be heard from the
speakers.
“PROTECT” appears on the display and no
operations can be done.
This unit does not work at all.
“AUX IN” cannot be selected.
Disc playback
FM/AM
SSM automatic presetting does not work.
Static noise while listening to the radio.
Connect the antenna firmly.
“AM” cannot be selected.
Check the <SRC SELECT> = <AM> setting. (See “Menu
operations” on page 3.)
Disc cannot be played back.
• CD-R/CD-RW cannot be played back.
• Tracks on the CD-R/CD-RW cannot be
skipped.
Disc can be neither played back nor
ejected.
Disc sound is sometimes interrupted.
Insert the disc correctly.
• Insert a finalized CD-R/CD-RW.
• Finalize the CD-R/CD-RW with the component which
you used for recording.
• Unlock the disc. (See page 2.)
• Eject the disc forcibly. (See page 1.)
• Stop playback while driving on rough roads.
• Change the disc.
• Check the cords and connections.
Insert a playable disc into the loading slot.
Press 0, then insert a disc correctly.
“NO DISC” appears on the display.
“PLEASE” and “EJECT” appear alternately
on the display.
Disc cannot be played back.
MP3/WMA playback
Noise is generated.
USB device playback
General
Remedy/Cause
• Adjust the volume to the optimum level.
• Make sure the unit is not muted/paused. (See page 1.)
• Check the cords and connections.
Check to be sure the terminals of the speaker leads are
covered with insulating tape properly, then reset the
unit. (See page 1.)
If “PROTECT” does not disappear, consult your JVC
car audio dealer or a company supplying kits.
Reset the unit. (See page 1.)
Check the <SRC SELECT> = <AUX IN> setting. (See
“Menu operations” on page 3.)
Store stations manually.
• If you turn off the power while listening to a track,
playback will start from where it had been stopped
previously next time you turn on the power.
• If no operation is done for about 60 seconds
after pressing MENU button, the operation will be
canceled.
Tuner operations
• During SSM search...
– All previously stored stations are erased and the
stations are stored anew.
– When SSM is over, the station stored in the lowest
preset number will be automatically tuned in.
• When storing a station manually, the previously
preset station is erased when a new station is
stored in the same preset number.
• If you try to assign titles to more than 30 station
frequencies, “NAME FULL” appears. Delete
unwanted titles before assignment.
Disc/USB operations
Caution for DualDisc playback
• The Non-DVD side of a “DualDisc” does not comply
with the “Compact Disc Digital Audio” standard.
Therefore, the use of Non-DVD side of a DualDisc
on this product may not be recommended.
General
• Use a disc with MP3/WMA tracks recorded in a format
compliant with ISO 9660 Level 1, Level 2, Romeo, or
Joliet.
• Add the extension code <.mp3> or <.wma> to the file
names.
Skip to another track or change the disc. (Do not add
the extension code <.mp3> or <.wma> to non-MP3 or
WMA tracks.)
Do not use too many hierarchical levels and folders.
A longer readout time is required
(“READING” keeps flashing on the display).
Tracks are not played back in the order
Playback order is determined when the files are
you have intended.
recorded.
“NO FILE” appears on the display.
Selected folder is an empty folder *. Select another
folder that contains MP3/WMA tracks.
* Folder that is physically empty or folder that contains data
but does not contain valid MP3/WMA track.
“NOT SUPPORT” appears on the display
Skip to the next track encoded in an appropriate format
and track skips.
or to the next non-copy-protected WMA track.
The elapsed playing time is not correct.
This sometimes occurs during playback. This is caused
by how the tracks are recorded on the disc.
The correct characters are not displayed
This unit can only display letters (upper case), numbers,
(e.g. album name).
and a limited number of symbols. (See page 2.)
Noise is generated.
The track played back is not an MP3/WMA track. Skip to
another file. (Do not add the extension code <.mp3>
or <.wma> to non-MP3 or WMA tracks.)
“READING” keeps flashing on the display.
• Readout time varies depending on the USB device.
• Do not use too many hierarchy or folders.
• Turn off the power then on again.
• Reattach the USB device again.
“NO FILE” appears on the display.
Selected folder is an empty folder*. Select another
folder that contains MP3/WMA tracks.
* Folder that is physically empty or folder that contains
data but does not contain valid MP3/WMA track.
“NOT SUPPORT” appears on the display
Skip to the next track encoded in an appropriate format
and track skips.
or to the next non-copy-protected WMA track.
Tracks/folders are not played back in the
The playback order is determined by the write-in time
order you have intended.
stamp. The first track/folder written into the USB device
will be the first track/folder for playback.
• “CANNOT PLAY” flashes on the display.
• Attach a USB device that contains tracks encoded in
• “NO USB” appears on the display.
an appropriate format.
• The unit cannot detect the USB device.
• Reattach the USB device again.
While playing a track, sound is sometimes The MP3/WMA tracks have not been properly copied
interrupted.
into the USB device.
Copy MP3/WMA tracks again into the USB device, and
try again.
Correct characters are not displayed (e.g. This unit can only display letters (upper case), numbers,
album name).
and a limited number of symbols. (See page 2.)
• This unit has been designed to reproduce CDs/
CD Texts, and CD-Rs (Recordable)/CD-RWs
(Rewritable) in audio CD (CD-DA), MP3 and WMA
formats.
• If you change the source while listening to a disc,
playback stops. Next time you select “CD” as the
playback source, playback will start from where it
had been stopped previously.
• If the ejected disc is not removed within
15 seconds, it is automatically inserted into the
loading slot again to protect it from dust. Playback
starts automatically.
Playing a CD-R or CD-RW
• Use only “finalized” CD-Rs or CD-RWs.
• This unit can play back multi-session discs;
however, unclosed sessions will be skipped while
playing.
• Some CD-Rs or CD-RWs may not be played back on
this unit:
– Discs are dirty or scratched.
– Moisture condensation has occurred on the lens
inside the unit.
– The pickup lens inside the unit is dirty.
– The files on the CD-R/CD-RW are written using the
“Packet Write” method.
– There are improper recording conditions (missing
data, etc.) or media conditions (stained, scratched,
warped, etc.).
• CD-RWs may require a longer readout time since
the reflectance of CD-RWs is lower than that of
regular CDs.
Playing an MP3/WMA disc
• This unit can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of
the letter case—upper/lower).
• This unit can show the names of albums, artists
(performer), and tag (Version 1.0, 1.1, 2.2, 2.3, or 2.4)
for MP3 files and for WMA files.
• This unit can display only one-byte characters. No
other characters can be correctly displayed.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 32 kbps — 320 kbps
– Sampling frequency of MP3:
32 kHz, 44.1 kHz, 48 kHz (for MPEG-1)
16 kHz, 22.05 kHz, 24 kHz (for MPEG-2)
– Sampling frequency of WMA:
22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz
– Disc format: ISO 9660 Level 1/ Level 2, Romeo,
Joliet, Windows extension
• The maximum number of characters for file/folder
names vary depending on the disc format used
(includes 4 extension characters—<.mp3> or
<.wma>).
– ISO 9660 Level 1: up to 12 characters; ISO 9660
Level 2: up to 31 characters; Romeo: up to 64
characters; Joliet: up to 32 characters; Windows
extension: up to 64 characters
• This unit can recognize a total of 512 files, 255
folders, and 8 hierarchical levels.
• This unit can play back files recorded in VBR
(variable bit rate).
Files recorded in VBR have a discrepancy in the
elapsed time display, and do not show the actual
elapsed time. In particular, this difference becomes
noticeable after performing the search function.
• This unit cannot play back the following files:
– MP3 files: encoded in MP3i and MP3 PRO format;
an inappropriate format; layer 1/2.
– WMA files: encoded in lossless, professional, and
voice format; not based upon Windows Media®
Audio; copy-protected with DRM.
– Files which have data such as AIFF, ATRAC3, etc.
• The search function works but search speed is not
constant.
Playing MP3/WMA tracks from a USB device
• While playing from a USB device, the playback
order may differ from other players.
• This unit may be unable to play back some USB
devices or some files due to their characteristics or
recording conditions.
• Depending on the shape of the USB devices and
connection ports, some USB devices may not be
attached properly or the connection might be
loose.
• Connect one USB mass storage class device to the
unit at a time. Do not use a USB hub.
• If the connected USB device does not have the
correct files, “CANNOT PLAY” appears.
• This unit can show Tag (Version 1.0, 1.1, 2.2, 2.3, or
2.4) for MP3 files and for WMA files.
• This unit can play back MP3/WMA files meeting the
conditions below:
– Bit rate: 32 kbps — 320 kbps
– Sampling frequency of MP3:
32 kHz, 44.1 kHz, 48 kHz (for MPEG-1)
16 kHz, 22.05 kHz, 24 kHz (for MPEG-2)
– Sampling frequency of WMA:
22.05 kHz, 32 kHz, 44.1 kHz, 48 kHz
• This unit can play back MP3 files recorded in VBR
(variable bit rate).
• The maximum number of characters for:
– Folder names: 32 characters; File names: 32
characters; MP3 Tag: 64 characters; WMA Tag: 32
characters
• This unit can recognize a total of 5 000 files, 255
folders (255 files per folder including folder without
unsupported files), and of 8 hierarchies.
• This unit does not support SD card reader.
• This unit cannot recognize a USB device whose
rating is other than 5 V and exceeds 500 mA.
• USB devices equipped with special functions such
as data security functions cannot be used with the
unit.
• Do not use a USB device with 2 or more partitions.
• This unit may not recognized a USB device
connected through a USB card reader.
• This unit may not play back files in a USB device
properly when using a USB extension cord.
• This unit cannot play back the following files:
– MP3 files: encoded in MP3i and MP3 PRO format;
an inappropriate format; layer 1/2.
– WMA files: encoded in lossless, professional, and
voice format; not based upon Windows Media®
Audio.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation
in the United States and/or other countries.
JVC bears no responsibility for any loss of the
data in the USB mass storage class device while
using this System.
4 – EN
EN_KD-S27[J]_f.indd 4
7/1/10 3:43:30 PM
Preparation
Maintenance
How to clean the connectors
To play new discs
Wipe the connectors with a cotton swab or cloth
moistened with alcohol.
Remove any rough areas from the
inner and outer edges of the disc.
Connectors
Moisture condensation
Moisture may condense on the lens inside the unit.
Eject the disc and leave the unit turned on for a few
hours until the moisture has evaporated.
To keep discs clean
Wipe in a straight line from center
of disc to edge. Do not use liquid
cleaners, thinners, or benzene.
You need the installation kits which corresponds to your car.
• Mark all the check boxes ( ) to make sure you have follow the instructions and the listed parts.
Check the battery system in your car
12 V DC, NEGATIVE ground
Do not use the following discs:
• Single CD—8 cm (3-3/16”) disc
• Warped disc
• Disc with sticker and sticker residue
• Disc with stick-on label
• Unusual shape disc
• C-thru Disc (semi-transparent disc)
• Disc with transparent or semi-transparent parts on
its recording area
Prepare this before installation
Parts list for installation and connection
Specifications
AUDIO AMPLIFIER SECTION
Power Output:
20 W RMS × 4 Channels at 4 Ω and
≤ 1% THD+N
Signal-to-Noise Ratio:
80 dBA (reference: 1 W into 4 Ω)
Load Impedance:
4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range:
Bass:
±12 dB (60 Hz, 80 Hz, 100 Hz, 200 Hz)
Q1.0, Q1.25, Q1.5, Q2.0
Middle: ±12 dB (0.5 kHz, 1.0 kHz, 1.5 kHz,
2.5 kHz)
Q0.75, Q1.0, Q1.25
Treble: ±12 dB (10.0 kHz, 12.5 kHz, 15.0 kHz,
17.5 kHz)
Q (Fixed)
Frequency Response: 40 Hz to 20 000 Hz
Line-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Subwoofer-Out Level/Impedance:
2.5 V/20 kΩ load (full scale)
Output Impedance: 1 kΩ
Other Terminal:
USB input jack, AUX (auxiliary)
input jack, Antenna input
TUNER SECTION
Frequency Range:
FM:
87.5 MHz to 107.9 MHz
(with channel interval set to 100 kHz or
200 kHz)
87.5 MHz to 108.0 MHz
(with channel interval set to 50 kHz)
AM:
530 kHz to 1 710 kHz
(with channel interval set to 10 kHz)
531 kHz to 1 602 kHz
(with channel interval set to 9 kHz)
[FM Tuner]
Usable Sensitivity: 9.3 dBf (0.8 μV/75 Ω)
50 dB Quieting Sensitivity: 16.3 dBf (1.8 μV/75 Ω)
Alternate Channel Selectivity (400 kHz): 65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 40 dB
[AM Tuner]
Sensitivity/Selectivity: 20 μV/40 dB
CD PLAYER SECTION
Type:
Compact disc player
Signal Detection System: Non-contact optical pickup
(semiconductor laser)
Number of channels:
2 channels (stereo)
Frequency Response:
5 Hz to 20 000 Hz
Dynamic Range:
96 dB
Signal-to-Noise Ratio: 98 dB
Wow and Flutter:
Less than measurable limit
MP3 Decoding Format: MPEG1/2 Audio Layer 3
Max. Bit Rate: 320 kbps
WMA (Windows Media® Audio) Decoding Format:
Max. Bit Rate: 320 kbps
A Control panel
B Sleeve
C Trim plate
D Power cord
USB SECTION
USB Standard:
USB 1.1, USB 2.0
Data Transfer Rate (Full Speed): Max. 12 Mbps
Compatible Device:
Mass storage class
Compatible File System: FAT 32/16/12
Playable Audio Format: MP3/WMA
Max. Current:
DC 5 V 500 mA
GENERAL
Power Requirement:
Operating Voltage:
DC 14.4 V (11 V to 16 V
allowance)
Grounding System:
Negative ground
Allowable Operating Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W × H × D):
Installation Size (approx.):
182 mm × 52 mm × 160 mm
(7-3/16” × 2-1/16” × 6-5/16”)
Panel Size (approx.):
188 mm × 58 mm × 6 mm
(7-7/16” × 2-5/16” × 1/4”)
Mass (approx.):
1.3 kg (2.9 lbs) (excluding
accessories)
Design and specifications are subject to change
without notice.
If a kit is necessary for your car, consult your
telephone directory for the nearest car audio
speciality shop.
Having TROUBLE with operation?
Please reset your unit
E Handles
F Remote controller / Battery
Troubleshooting
• The fuse blows.
] Are the red and black leads connected correctly?
• Power cannot be turned on.
] Is the yellow lead connected?
• No sound from the speakers.
] Is the speaker output lead short-circuited?
• Sound is distorted.
] Is the speaker output lead grounded?
] Are the “–” terminals of L and R speakers grounded in common?
• Noise interfere with sounds.
] Is the rear ground terminal connected to the car’s chassis using shorter and thicker cords?
• This unit becomes hot.
] Is the speaker output lead grounded?
] Are the “–” terminals of L and R speakers grounded in common?
• This unit does not work at all.
] Have you reset your unit?
Still having trouble??
Call 1-800-252-5722 (USA ONLY)
http://www.jvc.com
5 – EN
EN_KD-S27[J]_f.indd 5
7/1/10 3:43:30 PM
The following illustration shows a typical installation. If you are not sure how to install this unit correctly, contact your JVC car audio dealer or a company supplying kits.
In-dash mounting
See “Electrical connections” below.
When installing the unit without using the sleeve
Removing the unit
In a Toyota car for example, first remove the car radio and install the unit in its place.
Release the rear section first...
INSTALLATION / CONNECTION
Installation
8 mm (3/8")
Flat head screws—M5 × 8 mm (3/8") *2
Pocket
Bracket *2
Electrical connections
Make sure to disconnect the battery’s negative terminal.
• Be sure to ground this unit to the car’s chassis again after installation.
High
Note:
It is recommended to connect to the speakers with maximum power of more than 50 W (both at the rear and at the front, with an impedance of 4 Ω to 8 Ω). If the
maximum power is less than 50 W, change “AMP GAIN” setting to prevent the speakers from being damaged (see “Menu operations” on page 3).
Heat sink
Typical connections
Connecting the external amplifier or subwoofer
IMPORTANT: A custom wiring harness (separately purchased) which is suitable for your car is
recommended for connection between the unit and your car.
• Consult your JVC car audio dealer or a company supplying kits for details.
Remote lead
Antenna terminal
Rear line out
Remote lead (blue with white stripe)
Set “L/O MODE” to “REAR”
(See “Menu operations” on page 3.)
You can connect a power amplifier for
rear speakers.
Rear ground terminal
15 A fuse
Y-connector *2
To the remote lead of other
equipment or automatic
antenna if any
Signal cord *2
Rear
speakers
Connect only the front speakers
if your speaker system is twospeaker system.
Black
Front speaker
(left)
Front speakers
Set “L/O MODE” to “SUB.W”
(See “Menu operations” on page 3.)
You can also connect a subwoofer to
the REAR LINE OUT terminals.
Ignition
switch
White with black stripe
JVC Amplifier
To the metallic body
or chassis of the car
White
JVC Amplifier
or
Subwoofer
Gray with black stripe
Front speaker
(right)
Yellow *3
Gray
Red
Green
Purple with black stripe
Rear speaker
(right)
PRECAUTIONS on power supply and speaker connections
Fuse block
Green with black stripe
Rear speaker
(left)
To a live terminal in the
fuse block connecting
to the car battery
(bypassing the ignition
switch) (constant 12 V)
Purple
To an accessory
terminal in the fuse
block
Blue with white
stripe
To the remote lead of other
equipment or automatic
antenna if any (200 mA max.)
*1 When you stand the unit, be careful not to damage the fuse on the rear.
*2 Not supplied for this unit.
*3 Before checking the operation of this unit prior to installation, this lead must be connected, otherwise the power
cannot be turned on.
*4 Firmly attach the ground wire to the metallic body or to the chassis of the car—to the place uncoated with
paint (if coated with paint, remove the paint before attaching the wire). Failure to do so may cause damage to
the unit.
6 – EN
EN_KD-S27[J]_f.indd 6
7/1/10 3:43:30 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising