DMP Integration User Guide.book

DMP Integration User Guide.book
C•CURE® 9000
DMP XR500N Integration User Guide
REVISION A0
6 Technology Park Drive
Westford, MA 01886-3140
http://www.swhouse.com
Fax: 978-577-4392 Phone: 978-577-4000
Copyright and Trademarks
C•CURE® and Software House are registered trademarks of Tyco International Ltd. and its
respective Companies.
The trademarks, logos, and service marks displayed on this document are registered in the
United States [or other countries]. Any misuse of the trademarks is strictly prohibited and
Tyco International Ltd. will aggressively enforce its intellectual property rights to the fullest
extent of the law, including pursuit of criminal prosecution wherever necessary. All
trademarks not owned by Tyco International Ltd. are the property of their respective owners,
and are used with permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual products may
vary from photos. Not all products include all features. Availability varies by region; contact
your regional sales manager.
Software version: C•CURE 9000
Document Number: UM-250
Revision Number: A0
Print Date: June 2011
This manual is proprietary information of Software House. Unauthorized reproduction of any
portion of this manual is prohibited. The material in this manual is for information purposes
only. It is subject to change without notice. Software House assumes no responsibility for
incorrect information this manual may contain.
Copyright © 2011 by Tyco International Ltd. and its respective companies.
All rights reserved.
Tab le o f C on t en ts
Preface i
How to Use this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii
Finding More Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
Chapter 1
Introduction
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Chapter 2
Installation
Installation Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking Networks Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Checking System Privileges . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Database Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-3
2-4
2-4
2-5
Installing the DMP XR500N Integration Interface . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Running the Setup Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Starting the Server Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-11
Uninstalling the DMP XR500N Integration Interface . . . . . . . . . . . . . . . . . . . . . 2-13
To Uninstall DMP XR500N Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Chapter 3
Configuring DMP to Communicate with C•CURE 9000
Configuring DMP Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
DMP XR500N Integration User Guide
iii
Table of Contents
Chapter 4
Configuring .XML
Configuring DMPConfiguration.xml . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Chapter 5
DMP Controller Editor
DMP Controller-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-2
DMP Controller-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
DMP Controller-General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
DMP Controller-Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
DMP Controller-Main Board Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
DMP Controller-Keypad Bus Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10
DMP Controller-Keypad Bus Devices Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . 5-11
DMP Controller-LX and Wireless Devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12
DMP Controller-LX and Wireless Devices Tab Definitions . . . . . . . . . . . . . . . . . . . . 5-13
DMP Controller-Triggers Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
DMP Controller-Triggers Devices Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-14
DMP Controller-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
DMP Controller-Groups Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-17
DMP Controller-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-19
DMP Controller-Status Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-20
DMP Controller-State Images Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-21
Chapter 6
DMP-Intrusion Area
DMP Intrusion Area-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
DMP Intrusion Area-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
DMP Intrusion-Area General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
DMP Intrusion Area-Zones Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
DMP Intrusion Area-Shifts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
DMP Intrusion Area-Triggers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
DMP Intrusion Area-Triggers Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-8
DMP Intrusion Area-Groups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
DMP Intrusion Area-Groups Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-9
iv
DMP XR500N Integration User Guide
Table of Contents
DMP Intrusion Area-Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
DMP Intrusion Area-Status Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12
DMP Intrusion Area-State Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Arming and Disarming an Area from Monitoring Station . . . . . . . . . . . . . . . . . 6-14
Chapter 7
DMP-Input
DMP Inputs-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
DMP Input-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
DMP Input-General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-6
DMP Input-Triggers Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
DMP Input-Triggers Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
DMP Input-Triggers Tab Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-8
DMP Input-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
DMP Input-Groups Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
DMP Input-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
DMP Input-Status Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
DMP Inputs-State Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
Chapter 8
DMP-Output
DMP Outputs-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2
DMP Output-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
DMP Output General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-6
DMP Output-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
DMP Output-Groups Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
DMP Output-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
DMP Output-Status Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10
DMP Output-State Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-11
Chapter 9
DMP Device Editor
DMP Device-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-2
DMP Secondary Device-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
DMP XR500N Integration User Guide
v
Table of Contents
DMP Secondary Device General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6
DMP Secondary Device-Inputs Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
DMP Secondary Device-InputsTab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
DMP Secondary Device-Outputs Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-8
DMP Secondary Device-OutputsTab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-9
Chapter 10
DMP User Profile
DMP User Profile-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-2
DMP User Profile-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
DMP User Profile-General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-6
DMP User Profile-Menu Option Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
DMP User Profile-Menu Option Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-7
DMP User Profile-Shifts Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-10
DMP User Profile-C•CURE Personnel Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
Chapter 11
DMP User
DMP User-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2
DMP User-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-5
DMP User General Tab Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
Chapter 12
Event and Action
Event and Action-Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-2
Information about DMP-Specific Actions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
Actions and Target Object . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-3
DMP-Specific Action Configuration Example . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
DMP-Arm Intrusion Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-6
Action Tab-DMP Intrusion Area Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
DMP-Disarm Intrusion Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7
Action Tab-DMP Disarm Intrusion Area Definitions . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
DMP-Bypass Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-8
Action Tab-DMP Bypass Input Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
DMP-Reset Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9
Action Tab-DMP Reset Input Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
vi
DMP XR500N Integration User Guide
Table of Contents
DMP-Synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-10
Action Tab-DMP Synchronize Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-11
Chapter 13
Limitations
Limitations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-2
Chapter 14
Troubleshooting
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-2
Problem: 2
Solution: 2
Problem: 2
Solution: 2
Problem: 2
Solution: 3
Problem: 3
Solution: 3
Problem: 3
Solution: 3
Problem: 3
Solution: 3
Problem: 4
Solution: 4
Problem: 4
Solution: 4
Index
DMP XR500N Integration User Guide
vii
Table of Contents
viii
DMP XR500N Integration User Guide
List of Figures
List of Figures
Figure 1-1: DMP XR500N Integration Architecture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6
Figure 2-1: Privileges Error Message . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Figure 2-2: : DMP XR500N Integration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-6
Figure 2-3: Welcome Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Figure 2-4: Database Server Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7
Figure 2-5: Custom Setup Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-6: Select features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-8
Figure 2-7: Ready to Install Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-9
Figure 2-8: Installation Complete Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-10
Figure 2-9: Add/Remove Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12
Figure 2-10: Program Maintenance Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-13
Figure 2-11: Dropping Database Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-14
Figure 2-12: "Ready to Remove" Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-15
Figure 2-13: Uninstalling Process Dialog Box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Figure 2-14: InstallShield Wizard Completed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17
Figure 3-1: DMP Hardware Tree . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2
Figure 4-2: Creating New Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
Figure 4-3: DMP Controller Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-4: Deleting DMP Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4
Figure 4-5: DMP Controller-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6
Figure 4-6: DMP Controller-Main Board Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8
Figure 4-7: DMP Controller-Keypad Bus Devices Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10
Figure 4-8: DMP Controller-LX and Wireless Devices Tab . . . . . . . . . . . . . . . . . . . . . . . . 4-12
Figure 4-9: DMP Controller-Triggers Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-14
Figure 4-10: DMP Controller-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-17
Figure 4-11: : DMP Controller-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-19
Figure 4-12: DMP Controller-State Images Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-21
DMP XR500N Integration User Guide
ix
List of Figures
Figure 5-1: DMP Intrusion Area-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3
Figure 5-2: DMP Intrusion Area-Zones Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
Figure 5-3: DMP Intrusion Area-Shifts Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
Figure 5-4: DMP Intrusion Area-Triggers Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Figure 5-5: DMP Intrusion Area-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Figure 5-6: DMP Intrusion Area-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11
Figure 5-7: DMP Intrusion Area-State Images Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13
Figure 6-1: DMP Inputs-Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Figure 6-2: DMP Input Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Figure 6-3: DMP Input-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Figure 6-4: DMP Input-Triggers Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Figure 6-5: DMP Input-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-11
Figure 6-6: DMP Input-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-13
Figure 6-7: DMP Input Area-State Images Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-15
Figure 7-1: DMP Output-Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Figure 7-2: DMP Output deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
Figure 7-3: DMP Output-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-5
Figure 7-4: DMP Output-Groups Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
Figure 7-5: DMP Output-Status Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
Figure 7-6: DMP Output-State Images Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
Figure 8-1: DMP Device-Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3
Figure 8-2: DMP Device Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-4
Figure 8-3: DMP Device-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5
Figure 8-4: DMP Secondary Device-Inputs Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-7
Figure 8-5: DMP Secondary Device-Outputs Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8
Figure 9-1: DMP User Profile-Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Figure 9-2: DMP User Profile Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-3
Figure 9-3: DMP User Profile-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-5
Figure 9-4: DMP User Profile-Menu Option Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-7
Figure 9-5: DMP User Profile-Shifts Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-10
Figure 9-6: DMP User Profile-C•CURE Personnel Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-11
Figure 10-1: DMP User-Dynamic View . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10- 3
Figure 10-2: DMP User Deletion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-3
Figure 10-3: DMP User-General Tab . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-5
x
DMP XR500N Integration User Guide
List of Figures
Figure 11-1: DMP-Specific Actions List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-3
Figure 11-2: Action Tab-DMP-Arm Intrusion Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-6
Figure 11-3: Action Tab-DMP-Disarm Intrusion Area . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-7
Figure 11-4: Action Tab-DMP-Bypass Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-8
Figure 11-5: Action Tab-DMPReset Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-9
Figure 11-6: Action Tab-DMP-Synchronize . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-10
DMP XR500N Integration User Guide
xi
List of Figures
xii
DMP XR500N Integration User Guide
Preface
DMP XR500NIntegration User Guide is for new and experienced DMP XR500N
system users. The manual describes the features of the C•CURE 9000 and
DMP XR500N integration system.
This chapter covers
How to Use this Manual ................................................................................................... ii
Finding More Information .............................................................................................. iv
Conventions .........................................................................................................................v
DMP XR500N Integration User Guide
i
How to Use this Manual
How to Use this Manual
This manual includes the following sections. Turn to the appropriate section
for the information you need.
"Chapter 1": Introduction
Provides basic information about the DMP XR500N Integration product.
"Chapter 2": Installation
Describes how to install the DMP XR500N Integration software on C•CURE
9000.
"Chapter 3": Configuring DMP Panel
Describes how to configure DMP panel.
"Chapter 5": DMP Controller Editor
Describes how to use the DMP Controller Editor to create a basic
configuration in the C•CURE 9000 system.
"Chapter 6": DMP-Intrusion Area
Describes how to create, delete and edit using the DMP Intrusion Area.
"Chapter 7": DMP-Input
Describes how to configure the Inputs on the Main Board.
"Chapter 8": DMP-Output
Describes how to configure the Outputs on the Main Board.
ii
DMP XR500N Integration User Guide
How to Use this Manual
"Chapter 9": DMP Device Editor
Describes how to configure the DMP XR500N Secondary devices.
"Chapter 10": DMP User Profile
Describes how to configure and maintain the User Profiles of DMP XR500N.
"Chapter 11": DMP User
Describes how to configure and maintain DMP XR500N users.
"Chapter 12": Event and Action
Describes how to create events with actions.
"Chapter 13": Limitations
Lists some of the limitations of C•CURE 9000 DMP XR500N integration.
"Chapter 14": Troubleshooting
Helps you to resolve the problems.
DMP XR500N Integration User Guide
iii
Finding More Information
Finding More Information
You can access C•CURE 9000 manuals and online Help for more information
about C•CURE 9000.
Manuals
C•CURE 9000 software manuals and Software House hardware manuals are
available in Adobe PDF format on the C•CURE 9000 DVD. You can access the
manuals if you copy the appropriate PDF files from the C•CURE 9000
Installation DVD English\Manuals folder and install the Adobe Acrobat
Reader. Adobe Acrobat Reader can be installed from the C•CURE 9000
Installation DVD English\Reader folder. The available C•CURE 9000 and
Software House manuals are listed in the C•CURE 9000 Getting Started
Guide Product Guide and Help section, and appear as hyperlinks in
online.pdf file on the C•CURE 9000 DVD in the English\Manuals folder.
These manuals are also available from the Software house Member Center
website (http://membercenter.swhouse.com/home/default.aspx).
Online Help
You can access C•CURE 9000 Help by pressing F1 or click Help from the
menu bar in the Administration/Monitoring Station applications.
Windows Help
You can get help for the Windows products by selecting Help from the
specific Windows Start menu or by going to the Microsoft website at
www.microsoft.com.
iv
DMP XR500N Integration User Guide
Conventions
Conventions
This guide uses the following text formats and symbols.
Convention
Meaning
Bold
This font indicates screen elements, and also indicates when you
should take a direct action in a procedure.
Bold font describes one of the following items:
Å "A command or character to type, or
Å "A button or option on the screen to press, or
Å "A key on your keyboard to press
Å "A screen element or name
NOTE
TIP
Regular italic font
Indicates a new term.
<text>
Indicates a variable.
Indicates a note. Notes call attention to any item of information that may
be of special importance.
Indicates an alternate method of performing a task.
Indicates a caution. A caution contains information essential to avoid
damage to the system. A caution can pertain to hardware or software.
Indicates a warning. A warning contains information that advises users
that failure to avoid a specific action could result in physical harm to the
user or to the hardware.
Indicates a danger. A danger contains information that users must know
to avoid death or serious injury.
DMP XR500N Integration User Guide
v
Conventions
vi
DMP XR500N Integration User Guide
1
Introduction
This chapter introduces the C•CURE 9000 DMP XR500N Integration software
that provides integration between the Digital Monitoring Products (DMP)
XR500N Security System and C•CURE 9000.
This chapter covers
Overview.......................................................................................................................... 1-2
Features ............................................................................................................................ 1-3
Architecture ..................................................................................................................... 1-5
DMP XR500N Integration User Guide
1-1
Overview
Overview
The C•CURE 9000 DMP XR500N Integration provides advanced, seamless
integration with the DMP Security System, allowing customers to monitor
their intrusion system devices from the C•CURE 9000 Monitoring Station,
monitor Controller status, and arm/disarm area(s) from the Administration
WorkStation.
The general DMP Security System is made up of DMP Controllers, one or
more keypads and various sensors and detectors. All keypads have an
audible indicator and command entry key. They are used to send commands
to the system and to display the current system status. The security system
has several zones of area protection, and each of these zones is connected to
one or more sensors, for example, motion detectors, door contacts, and so
forth. An alarm from the sensor is indicated by a corresponding zone.
The integration of the DMP product and the C•CURE 9000 product through
the Software House C•CURE 9000 Connected Program Kit provides
extensive system integration opportunities. It allows you to import a DMP
Controller configuration and acquire DMP Controller status changes. Area
and Zone event status, health status data and all alarms, troubles, and
emergency information from the DMP Security System are stored in C•CURE
9000s detailed journal.
1-2
DMP XR500N Integration User Guide
Features
Features
The following is a list of major features supported by C•CURE 9000 DMP
XR500N Integration:
„
The DMP driver queries system status of XR500N panel after C•CURE
9000 starts up. The system status includes:
• Printer
• Tamper
• Battery
• AC Power
• Telephone Line 1
• Telephone Line 2
• Wireless
„
The driver also supports tasks of access, command, and inquiry:
• Alarm silence
• Areas
• Sensor Reset
• Zones
• Outputs
„
The driver supports manual actions as follows:
• Area
– Arm
– Disarm
– Force Arm
• Output
– Activate
DMP XR500N Integration User Guide
1-3
Features
– Deactivate
– Pulse
– Momentary Output
• Input
– Reset
– Bypass
• Controller
– Synchronize
– Arm
– Disarm
– Force Arm
– Silence Alarm
– Reset Sensor
1-4
„
The ability to import controller configuration, devices, areas, inputs,
outputs, users, and user profiles. You can also export these objects
individually for reporting purposes.
„
You can select Multiple objects and assign a common parameter to objects
at once.
DMP XR500N Integration User Guide
Architecture
Architecture
The objective of the C•CURE 9000 DMP XR500N Integration software is to
provide a standard interface between the DMP product family and C•CURE
9000 through an Ethernet port. The interface connects to the DMP controllers
and queries any changes in status and fetches the event messages and
communicates them to C•CURE 9000. C•CURE 9000 processes these
messages and communicates them to users as object state changes, activities,
events, and alarms, according to the way the DMP objects in the C•CURE
9000 database are configured.
The DMP XR500N Integration Interface gives you the ability to import a DMP
controller's configuration, areas and zones in C•CURE 9000, and arm/disarm
areas.
You can access the DMP XR500N Integration interface on the C•CURE 9000
Administration Client by clicking Hardware. The Hardware pane opens and
you can access an existing DMP controller or create a new one.
DMP XR500N Integration User Guide
1-5
Architecture
Figure 1-1: DMP XR500N Integration Architecture
1-6
DMP XR500N Integration User Guide
2
Installation
This chapter provides instructions for installing the DMP XR500N Integration
software on a C•CURE 9000 server or client system.
This chapter covers
Installation Overview ............................................................................................... 2-2
Installing the DMP XR500N Integration Interface.............................................. 2-6
Uninstalling the DMP XR500N Integration Interface ...................................... 2-13
DMP XR500N Integration User Guide
2-1
Installation Overview
Installation Overview
Before installing the C•CURE 9000 DMP XR500N Integration software, you
must first install C•CURE 9000 software on your target computer. For
information on installing C•CURE 9000, see C•CURE 9000 Installation and
Upgrade Guide.
Similar to the C•CURE 9000 system, the DMP XR500N Integration has client
and server components. You must install the client components on every
computer that runs C•CURE 9000 client applications, and you must install
the server components on the C•CURE 9000 server computer. The DMP
XR500N integration has the same hardware, software, and disk space
requirements as C•CURE 9000; if the target computer can install C•CURE
9000, then it satisfies DMP XR500N Integration requirements.
An installation wizard prompts you to install the C•CURE 9000 DMP
XR500N Integration software. You must perform the basic installation process
on each computer in your C•CURE 9000 system. Be sure to close all C•CURE
9000 and virus--checking applications on client workstations before
performing the installation.
When you install the C•CURE 9000 DMP XR500N Integration interface, the
installation program automatically creates a DMP Controller folder at the
Company Name root level of the Hardware Tree.
Table 2-1 on page 2-2 lists the steps to install and register the C•CURE 9000
DMP XR500N Integration on each computer in your C•CURE 9000 system.
Table 2-1: Standard Installation Tasks
Task
See
InstallC•CURE 9000.
C•CURE 9000 Installation and Upgrade
Guide
Close any open applications and disable viruschecking software.
Crossfire Services should be stopped if
C•CURE 9000 is already installed.
2-2
Perform the pre-installation steps.
“Before You Begin” on page 2-3
Start the C•CURE 9000 DMP XR500N
Integration installation program.
“Installing the DMP XR500N Integration
Interface” on page 2-6
DMP XR500N Integration User Guide
Installation Overview
Table 2-1: Standard Installation Tasks, continued
Task
See
Verify the license for the DMP software by
running the License program on your C•CURE
9000 server.
C•CURE 9000 Installation and Upgrade
Guide
When the installation and registration are
complete, restart the C•CURE 9000 services.
See C•CURE 9000 User Guide.
Before You Begin
You may need to perform some pre-installation steps before you install the
C•CURE 9000 DMP XR500N Integration software.
Ensure System Requirements
„
Pentium IV processor 3.4 GHz
„
For less than 10 controllers: Dual drives, Primary drive 80 GB, and
Secondary drive 80 GB (min 7200 rpm)
„
For 10 or more controllers: Dual drives; Primary drive 100 GB, and
Secondary drive 100 GB (min 7200 rpm)
„
4GB RAM
„
Network Card 100/1000 (MB/sec)
„
DVD Drive
Check for Qualified Operating Systems
„
Windows®2003 Standard Server (SP1) 32 bit OS
„
Windows®XP Professional (SP2) 32bit OS
„
Windows®2003 Enterprise Server (SP1) 32 bit OS
„
Windows®7 32 bit OS
„
Windows®2008 Server R2 Enterprise 64 bit OS
DMP XR500N Integration User Guide
2-3
Installation Overview
Qualified Software
„
SQL Server 2005 Express Edition
„
SQL Server 2005 Standard Edition
„
SQL Server 2008 Standard Edition
Checking Networks Status
If you are installing C•CURE 9000 on a corporate network, be sure to
coordinate with your corporate network administrator. Check that the
network is working properly.
Checking System Privileges
To perform the installation, you must have appropriate Window's
permissions. You must be in the local Administrators group, or have
equivalent privileges. See the Microsoft Operating System documentation or
your system administrator for more information.
If you do not have sufficient permissions, the following error message will
appear as shown in Figure 2-1 on page 2-5.
2-4
DMP XR500N Integration User Guide
Installation Overview
Figure 2-1: Privileges Error Message
Database Installation
If you are installing server components of the C•CURE 9000 DMP XR500N
Integration, the C•CURE 9000 DMP XR500N Integration adds some tables to
the C•CURE 9000 database. Currently, the C•CURE 9000 DMP XR500N
Integration does not support installation with C•CURE 9000 on an Oracle
database. Therefore , you must install the software on a C•CURE 9000 system
that is using SQL Server 2005. The C•CURE 9000 DMP XR500N Integration
installation program automatically finds the C•CURE 9000 database and
adds the tables and initial data.
DMP XR500N Integration User Guide
2-5
Installing the DMP XR500N Integration Interface
Installing the DMP XR500N Integration Interface
You can install the C•CURE 9000 DMP XR500N Integration on a local
computer from a shared drive over a network.
NOTE
If you use the SQL Server 2005 Express Edition, you must have TCP/IP
enabled and must have the SQL Server Browser and SQL Server
(SQLEXPRESS) running.
To Install on a Local Computer
1. Log into the server or client with Window's administration privileges.
2. Download the setup from a shared drive over a network.
To Install over the Network
1. Log into the server or client with the appropriate Window's privileges.
2. From your system, map a share to the shared drive over the Network.
3. Run the C·CURE_9000_DMP_Integration.exe application from the root
folder of the mapped drive.
Running the Setup ProgramXR500N
To install the C•CURE 9000 DMP XR500N Integration, run the DMP.exe
program in the root folder of the shared drive over a network..
To Run the Setup Program
1. Click Next.
2. The Setup program then checks the system to see if it meets minimum
requirements. If minimum requirements are met, a Welcome dialog box
opens, as shown in Figure 2-2 on page 2-7.
2-6
DMP XR500N Integration User Guide
Installing the DMP XR500N Integration Interface
Figure 2-2: Welcome Dialog Box
3. Click Next to continue the installation. A Database Server dialog box
opens, as shown in Figure 2-3 on page 2-7. Click Browse to select the
Database server you want install to and click Next.
Figure 2-3: Database Server Dialog Box
DMP XR500N Integration User Guide
2-7
Installing the DMP XR500N Integration Interface
4. The Custom Setup dialog box opens, as shown in Figure 2-4 on page 2-8.
You can select the program features you want to install. You can also click
Change to choose an installation path .
Figure 2-4: Custom Setup Dialog Box
5. If you do not want to install the server, click to the left of the server and
select The feature will not be available. See Figure 2-5 on page 2-8
Figure 2-5: Select features
6. Use the same method if you do not want to install the client.
2-8
DMP XR500N Integration User Guide
Installing the DMP XR500N Integration Interface
Applicable only for C•CURE 9000 2.0 and later version.
Table 2-2: Server and Client for 2.0 and later version
Installation Type
Client
Server
Satellite Application Server
Yes
Yes
Master Applicatin Server
Yes
No
Standalone/1.9
Yes
Yes
Remote Client to SAS
Yes
No
Remote Client to MAS
Yes
No
Remote Client to
Standalone
Yes
No
For selections refer to Step 4
7. After you select the program features and the installation path, click Next
to continue. The Ready to Install the Program dialog box appears, as
shown in Figure 2-6 on page 2-9. Click Install to start the installation.
Figure 2-6: Ready to Install Dialog Box
DMP XR500N Integration User Guide
2-9
Installing the DMP XR500N Integration Interface
8. After a few minutes, the Installation Wizard Completed dialog box
appears. See Figure 2-7 on page 2-11.
2-10
DMP XR500N Integration User Guide
Installing the DMP XR500N Integration Interface
Figure 2-7: Installation Complete Dialog Box
9. Click Finish to complete the installation process.
10. After finishing the installation of the C•CURE 9000 DMP XR500N
Integration Software, restart the CrossFire and CrossFire Server
Component Framework service. For more details on CrossFire, see
C•CURE 9000 User Guide.
Starting the Server Components
Before you can import a DMP controller configuration, you must start the
DMP XR500N Integration server component using the C•CURE 9000 Server
Management Application Server Components tab.
1. From the Start Menu, select Start>All Programs>Software
House>Server Configuration.
2. The C•CURE 9000 Server Management application opens.
DMP XR500N Integration User Guide
2-11
Installing the DMP XR500N Integration Interface
3. Click the Server Components tab.
4. Right-click DMP Server Integration interface and select Start Server
Component from the context menu.
5. When the server component icon for DMP XR500N Integration changes
from disabled to enabled, you can use the DMP XR500N Integration
Interface.
2-12
DMP XR500N Integration User Guide
Uninstalling the DMP XR500N Integration Interface
Uninstalling the DMP XR500N Integration Interface
This section describes how to uninstall the C•CURE 9000 DMP XR500N
Integration software from the server computer and from each client computer
in your security system.
The Uninstall process removes all software components that were installed on
the computer by the C•CURE 9000 DMP XR500N Integration software
program.
Once the uninstall process completes, the computer will be in a clean state.
To Uninstall DMP XR500N Integration
1. From the Window's Start menu, select Start>Control Panel>Add or
Remove Programs .
2. Double-click Add/Remove Programs. The Add/Remove Programs dialog
box appears. Figure 2-8 on page 2-13.
Figure 2-8: Add/Remove Programs
3. Select C•CURE 9000 DMP XR500N Integration from the list.
DMP XR500N Integration User Guide
2-13
Uninstalling the DMP XR500N Integration Interface
4. Click Change. The Program Maintenance dialog box opens, as shown in
Figure 2-9 on page 2-14.
Figure 2-9: Program Maintenance Dialog Box
2-14
DMP XR500N Integration User Guide
Uninstalling the DMP XR500N Integration Interface
5. Select Remove and click Next. A dialog box appears for you to choose
whether to drop DMP XR500N Integration database tables or not. If yes,
select the box. If not, click Next .
Figure 2-10: Dropping Database Tables
DMP XR500N Integration User Guide
2-15
Uninstalling the DMP XR500N Integration Interface
6. The Remove the Program dialog box opens. See Figure 2-11 on page 2-16.
Click Remove to continue the deinstallation.
Figure 2-11: "Ready to Remove" Dialog Box
2-16
DMP XR500N Integration User Guide
Uninstalling the DMP XR500N Integration Interface
7. The Uninstalling C•CURE DMP 9000 Integration dialog box appears as
shown in Figure 2-12 on page 2-17.
Figure 2-12: Uninstalling Process Dialog Box
DMP XR500N Integration User Guide
2-17
Uninstalling the DMP XR500N Integration Interface
8. After a few minutes, the Installshield Wizard Completed dialog box
appears, as shown in Figure 2-13 on page 2-18. Click Finish to exit the
wizard.
Figure 2-13: InstallShield Wizard Completed
2-18
DMP XR500N Integration User Guide
3
Configuring DMP to
Communicate with
C•CURE 9000
This chapter provides instructions on how to configure DMP panel to
communicate with C•CURE 9000.
This chapter covers
‹
Configuring DMP Panel............................................................................................. 3-2
DMP XR500N Integration User Guide
3-1
Configuring DMP Panel
Configuring DMP Panel
„
The DMP Panel Software Version supported by the C•CURE 9000
Integration : V206
„
The Communication Mode supported by the Integration: Network (TCP/
IP)
„
Basic Configurations in the DMP Panel to connect to C•CURE 9000:
• Unique Account Number
• Unique IP Address
To Configure Account Number in the DMP Panel
1. To Access the Programmer perform the following:
a. Install the reset jumper across the two J16 reset pins for two seconds.
b. Remove the reset jumper and place it over just one pin for future use.
c. Enter the code 6653 (PROG) into 32-character alphanumeric display.
d. Press COMMAND it displays PROGRAMMER.
2. Navigate to COMMUNICATION using CMD.
3. Press SELECT to go into the COMMUNICATION section.
4. In the COMMUNICATION section select Account Number option. This
can be configured using Select Keys and DATA ENTRY DIGIT keys.
5. Enter Account Number
6. Press CMD and then ? (Back) to revert to Programmer Section.
7. Pess CMD till "STOP" option appears.
8. Press the "Select Key". The panel displays "Saving", "Please Wait"
messages.
NOTE
3-2
The same account number needs to be configured in the Controller Object
in C•CURE 9000.
DMP XR500N Integration User Guide
Configuring DMP Panel
To Configure Network parameters in the DMP Panel
1. To Access the Programmer perform the following:
a. Install the reset jumper across the two J16 reset pins for two seconds.
b. Remove the reset jumper and place it over just one pin for future use.
c. Enter the code 6653 (PROG) into 32-character alphanumeric display.
d. Press COMMAND it displays PROGRAMMER
2. Navigate to NETWORK OPTIONS using the CMD.
3. Press the SELECT to go into the NETWORK OPTIONS section.
4. In the NETWORK OPTIONS section select LOCAL IP ADDRESS
option. This can be configured using Select Keys and DATA ENTRY
DIGIT keys.
5. Enter LOCAL IP ADDRESS, Subnet Mask, DNS Server, and Gateway
Address.
6. Press CMD and then ? (Back) to revert to Programmer Section.
7. Pess CMD till "STOP" option appears.
8. Press the "Select Key". The panel displays "Saving", "Please Wait"
messages.
NOTE
The same IP Address needs to be configured in the Controller Object in
C•CURE 9000.
The same procedure needs to be followed for configuring the Subnet
Mask, DNS Server, and Gateway Address.
Subnet Mask, DNS Server, Gateway Address, and IP Address can all be
configured at once.
To Change the network settings, such as IP Address, Gateway Address,
and so on. DHCP option should be set to NO. If DHCP option is set to
YES, then the addresses cannot be configured.
DMP XR500N Integration User Guide
3-3
Configuring DMP Panel
To Configure Remote Key in the DMP Panel
1. To Access the Programmer perform the following:
a. Install the reset jumper across the two J16 reset pins for two seconds.
b. Remove the reset jumper and place it over just one pin for future use.
c. Enter the code 6653 (PROG) into 32-character alphanumeric display.
d. Press COMMAND it displays PROGRAMMER
2. Navigate to REMOTE OPTIONS using the CMD.
3. Press the SELECT to go into the REMOTE OPTIONS section.
4. In the REMOTE OPTIONS section select REMOTE KEY option. This can
be configured using Select Keys and DATA ENTRY DIGIT keys.
5. Enter REMOTE KEY.
6. Press CMD and then ? (Back) to revert to Programmer Section.
7. Pess CMD till "STOP" option appears.
8. Press the "Select Key". The panel displays "Saving", "Please Wait"
messages.
NOTE
The same Remote Key needs to be configured in the Controller Object in
C•CURE 9000.
Remote key is not mandatory.
To Configure Programming Port in the DMP Panel:
1. To Access the Programmer perform the following:
a. Install the reset jumper across the two J16 reset pins for two seconds.
b. Remove the reset jumper and place it over just one pin for future use.
c. Enter the code 6653 (PROG) into 32-character alphanumeric display.
d. Press COMMAND it displays PROGRAMMER
3-4
DMP XR500N Integration User Guide
Configuring DMP Panel
2. Navigate to REMOTE OPTIONS using the CMD.
3. Press the SELECT to go into the REMOTE OPTIONS section.
4. In the REMOTE OPTIONS section select NETWORK PROG PORT
option. This can be configured using Select Keys and DATA ENTRY
DIGIT keys.
5. Enter NETWORK PROG PORT.
6. Press CMD and then ? (Back) to revert to Programmer Section.
7. Pess CMD till "STOP" option appears.
8. Press the "Select Key". The panel displays "Saving", "Please Wait"
messages.
NOTE
The same Programming Port value needs to be configured in the
Controller Object in C•CURE 9000.
To configure Date and Time in DMP Panel:
1. Access the User Menu.
2. Press COMMAND until TIME? displays. Press any Select key.
3. The panel displays the current Day and Time.
4. Press the COMMAND key. The panel displays the current Date.
5. Press the COMMAND key to make any changes.
6. The panel displays TIME DAY DATE.
7. Select TIME, the panel displays - : AM and PM. Enter the current time
and select AM or PM.
8. The panel changes back to TIME DAY DATE.
9. Select DAY , the panel displays SUN MON TUE WED.
10. Press the COMMAND key to display THU FRI SAT. Select the correct
day. Use the Back Arrow key to toggle between the different day of the week.
DMP XR500N Integration User Guide
3-5
Configuring DMP Panel
11. Select DATE, the panel displays MONTH:- Enter up to 2 digits for the
month.
12. Press COMMAND, the panel displays DAY:- Enter up to 2 digits for the
day.
13. Press COMMAND, the panel displays YEAR:- Enter up to 2 digits for the
year.
14. Press COMMAND. The display returns to the TIME DAY DATE.
15. Press Back Arrow key to exit the User Menu.
To configure Receiver Port
This displays the Events messages
1. To Access the Programmer perform the following:
a. Install the reset jumper across the two J16 reset pins for two seconds.
b. Remove the reset jumper and place it over just one pin for future use.
c. Enter the code 6653 (PROG) into 32-character alphanumeric display.
d. Press COMMAND, panel displays PROGRAMMER.
2. Navigate to REMOTE OPTIONS using CMD.
3. Press SELECT to go into the REMOTE OPTIONS section.
4. In the REMOTE OPTIONS section select Entre Connection option.
5. Change it to NET.
6. Change ENTRE INCOMING TCP PORT to the port at which you want
to receive the Panel's Event Messages.
7. Change ENTRE IP to the IP at which you want to receive the Panel's
Event Messages. This should be the C•CURE Server's IP Address.
8. Change the ENTRE OUTBOUND TCP PORT to the port number
specified in ENTRE INCOMING TCP PORT, that is both these port
numbers should be same and this port number should be specified in the
Receiver Port field in DMP Controller screen in C•CURE .
3-6
DMP XR500N Integration User Guide
Configuring DMP Panel
9. Change ENTRE CHECK-IN MINUTES to value 3..
NOTE
The Receiver Port needs to be configured in the Controller Object in
C•CURE 9000.
After the communication is established, the required Zones, Outputs, Areas
and other objects are to be programmed in the panel see "LT-0679Programming-Guide" for more information.
DMP XR500N Integration User Guide
3-7
Configuring DMP Panel
3-8
DMP XR500N Integration User Guide
4
Configuration .XML
This chapter provides instructions on how to change the
DMPConfiguration.xml.
This chapter covers
‹
Configuring DMPConfiguration.xml............................................................................ 4-2
DMP XR500N Integration User Guide
4-1
Configuring DMPConfiguration.xml
Configuring DMPConfiguration.xml
This configuration file helps you change the behavior of all the configured
DMP controllers in C•CURE in a controlled manner. Path: Software
House\SWHSystem\ServerComponents\DMPConfiguration.xml
Fields that can be changed in the XML File are as follows:
• ReAttempInterval (Re-attempt Interval) - This is the time value desired
between two successive attempts from the DMP Server, when no
response from the panel is received. Range is 2000-25000 mill seconds.
Default is 10000.
• NumberOfRequestAttempts (Number of Request Attempts) indicates the number of reattempts that should be made in case we
donot get a response from panel. Range is 3-5. Default is 3.
• SystemStatusRequestInterval (System Status Request Interval) :
Indicates the timer interval of a request which is used to maintain a
TCP connection to the panel. Range is 1000-25000 mill seconds. Default
is 10000.
• ProtocolPacketLog (Protocol Packet Log) -Indicates whether the
packets exchanged between the Panel and the DMP Server are logged
in the TraceViewer. Default is False.
• TraceEnable (Trace Enable) - Indicates if the Trace messages are logged
in the TraceViewer. Default is True
4-2
DMP XR500N Integration User Guide
5
DMP Controller Editor
This chapter provides information about the DMP Controller Editor.
This chapter covers
DMP Controller-Overview....................................................................................... 5-2
DMP Controller-General Tab.................................................................................. 5-6
DMP Controller-Main Board................................................................................... 5-8
DMP Controller-Keypad Bus Devices ................................................................. 5-10
DMP Controller-LX and Wireless Devices ......................................................... 5-12
DMP Controller-Triggers Tab ............................................................................... 5-14
DMP Controller-Groups Tab................................................................................. 5-17
DMP Controller-Status Tab ................................................................................... 5-19
DMP Controller-State Images Tab ....................................................................... 5-21
DMP XR500N Integration User Guide
5-1
DMP Controller-Overview
DMP Controller-Overview
A DMP controller is imported to C•CURE 9000 through the DMP Controller
dialog box. See Figure 5-1 on page 5-2. Once the DMP data import
(synchronization) is done, the dialog box shows the system version, the
communication IP and port, the partition and zone information.
To Access a Configured DMP Controller
1. In the Navigation pane of the C•CURE 9000 Administration Station, click
Hardware. The Hardware pane opens.
2. Open the Company Name folder by clicking to the left of the folder.
Figure 5-1: DMP Hardware Tree
3. Open the DMP Controller folder by clicking to the left of the folder.
4. To open the DMP Controller Editor, right-click the DMP icon or name and
select Edit. The DMP Controller editor opens with the General tab visible.
You can also access a DMP Controller in a dynamic view. See Step 4
on page 5-4.
To Create a DMP Controller object
1. In the Navigation pane of the C•CURE 9000 Administration
WorkStation, click Hardware to open the Hardware pane.
5-2
DMP XR500N Integration User Guide
DMP Controller-Overview
2. Open the Company Name folder by clicking to the left of the folder. In the
Company Name folder, right-click the DMP Controller and select New.
Figure 5-2: Creating New Controller
3. The DMP Controller editor opens. Enter a name for the Controller in the
Name field.
4. Click Save and Close to save and exit. See “To Import and Configure a
DMP Controller” on page 5-4.
To Delete a DMP Controller
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Controller from the Hardware pane drop-down list.
3. Click .... to open a Dynamic View showing all DMP Controller objects as
shown in Figure 5-3 on page 5-4.
DMP XR500N Integration User Guide
5-3
DMP Controller-Overview
Figure 5-3: DMP Controller Dynamic View
4. In the list, right-click the DMP Controller that you want to delete and
select Delete from the context menu. A message box appears stating "Are
you sure that you want to delete the selected DMP Controller object?" as
shown in Figure 5-4 on page 5-4.
Figure 5-4: Deleting DMP Controller
5. Click Yes in the message box to delete the Controller object.
To Import and Configure a DMP Controller
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Right-click on a DMP Controller placeholder object and select Edit.
3. Type an optional textual description for the DMP Controller in the
Description field.
4. Click the Enabled option to establish communication between C•CURE
9000 and the DMP Controller.
5. Click Synchronize. The configuration details of the DMP Controller will
be imported to C•CURE 9000.
6. You can click the Triggers tab to configure triggers for the DMP
Controller. See “DMP Controller-Triggers Tab” on page 5-14.
5-4
DMP XR500N Integration User Guide
DMP Controller-Overview
7. You can click the State Images tab to view the state images for the DMP
Controller. See “DMP Controller-State Images Tab” on page 5-21.
8. When you finish editing the DMP Controller configuration, click Save
and Close to save the configuration.
DMP XR500N Integration User Guide
5-5
DMP Controller-General Tab
DMP Controller-General Tab
The DMP General tab lets you select a communication port and shows you
the basic information and time zone of the controller. See “DMP ControllerGeneral Tab” on page 5-6.
Figure 5-5: DMP Controller-General Tab
5-6
DMP XR500N Integration User Guide
DMP Controller-General Tab
DMP Controller-General Tab Definitions
Table 5-1 on page 5-7 provides definitions for the fields on the DMP
Controller General tab.
Table 5-1: DMP Controller-General Tab Definition
Field
Description
Name
Enter a unique name up to 100 characters
long for the DMP Controller.
Description
Enter a general comment about the
Controller.
Enabled
Select the Enabled option to establish the
communication between C•CURE 9000
and the DMP Controller.
NOTE: If you cannot establish
communication successfully, please
check your connection.
Controller Info
Controller Type
Type of DMP controller (XR500N)
Account Number
Unique account number for DMP controller
(1-65535)
Remote Key
Alphanumeric key of maximum eight
characters
Communication Info
IP Address
Network address of DMP Controller
Programming Port
Programming port of DMP Controller
Receiving Port
Receiving port of C•CURE 9000 server
NOTE: If windows Fierwall is enabled on
C•CURE 9000 sever, then this port
details needs to be added in firewall
expection list.
Synchronization
Synchronize
Used to synchronize DMP Controller with
C•CURE 9000
Last Successful Synchronization
Date of the last successful synchronization
DMP XR500N Integration User Guide
5-7
DMP Controller-Main Board
DMP Controller-Main Board
The Main Board contains all the system (onboard) Inputs, such as Battery
Low, and Outputs.
Zones on Main Board are as follows:
• Eight 1K Ohm EOL burglary zones (zones 1 to 8)
• Two 3.3K Ohm EOL powered zone with reset (zones 9 and 10)
Figure 5-6: DMP Controller-Main Board Tab
DMP Controller-Main Board Tab Definitions
Table 5-2 on page 5-9 provides definitions for the fields on the DMP
Controller Main Board tab.
5-8
DMP XR500N Integration User Guide
DMP Controller-Main Board
Table 5-2: DMP Controller-Main Board Tab Definition
Field
Description
Main Board Inputs
Create all inputs
If the checkbox is enabled, all the Inputs on
DMP Main Board are enabled and their
messages can be seen on Monitoring
Station.
Delete all inputs
Deletes all the Main Board inputs if it is
checked.
Input Type
Battery Low
If enabled, the Main Board Battery Low
messages are displayed on the Monitoring
Station.
Power Failure
If enabled, the Main Board Power Failure
messages are displayed on the Monitoring
Station.
Printer
If enabled, the Main Board Printer
messages are displayed on the Monitoring
Station.
Tamper
If enabled, the Main Board Tamper
messages are displayed on the Monitoring
Station.
Wireless
If enabled, the Main Board Wireless
messages are displayed on the Monitoring
Station.
Telephone Line 1
If enabled Main Board Telephone Line 1
messages are displayed on the Monitoring
Station.
Telephone Line 2
If enabled Main Board Telephone Line 2
messages are displayed on the Monitoring
Station.
Intrusion zone (1-10)
If enabled Main Board Input (Intrusion
Zone) messages are displayed on the
Monitoring Station.
Main Board Outputs
Output (1-6)
There are six onboard outputs.
DMP XR500N Integration User Guide
5-9
DMP Controller-Keypad Bus Devices
DMP Controller-Keypad Bus Devices
The Keypad Bus Device is a collection of wires that connect the devices of an
alarm system.
You can connect up to sixteen of the following supervised keypads and
expansion modules to the keypad bus to
• Alphanumeric keypads
• Four- and/or single-zone expansion modules
• Single-zone detectors
Figure 5-7: DMP Controller-Keypad Bus Devices Tab
5-10
DMP XR500N Integration User Guide
DMP Controller-Keypad Bus Devices
DMP Controller-Keypad Bus Devices Tab Definitions
Table 5-3 on page 5-11 provides definitions for the fields on the DMP
Controller Keypad Bus Devices tab.
Table 5-3: DMP Controller-Keypad Bus Devices Tab Definition
Field
Description
Keypad bus devices
Create all devices
If the checkbox is enabled, all the keypad
bus devices are enabled and their
messages can be seen on Monitoring
Station.
Delete all devices
Deletes all the keypad bus devices if it is
checked.
Keypad bus device (1-16)
Sixteen keypad bus devices can be
connected to the DMP Controller.
DMP XR500N Integration User Guide
5-11
DMP Controller-LX and Wireless Devices
DMP Controller-LX and Wireless Devices
The LX-Bus and wireless device is a collection of wires that connect the
devices of an alarm system. DMP bus wires include both LX-Bus Devices and
wireless devices.
Figure 5-8: DMP Controller-LX and Wireless Devices Tab
DMP Controller-LX and Wireless Devices Tab Definitions
Table 5-4 on page 5-12 provides definitions for the fields on the DMP
Controller LX and Wireless Devices tab.
Table 5-4: DMP Controller-LX and Wireless Devices Tab Definition
Field
Description
LX Bus/Wireless Inputs and LX Bus Outputs
Create all devices
5-12
DMP XR500N Integration User Guide
If the checkbox is enabled, all the LX/
Wireless bus devices are enabled and their
messages can be seen on the Monitoring
Station.
DMP Controller-LX and Wireless Devices
Table 5-4: DMP Controller-LX and Wireless Devices Tab Definition
Field
Description
Delete all devices
Deletes all the LX/Wireless bus devices if it
is checked.
LX/ Wireless bus device
LX/Wireless bus devices can be connected
to the DMP Controller.
Key Fob Inputs/Wireless Outputs
Create
If the checkbox is enabled, the Key Fob
Inputs/Wireless device is enabled and the
messages can be seen on the Monitoring
Station.
Delete
Deletes the Key Fob Inputs/Wireless device
if it is checked.
Key Fob Inputs/Wireless device
One Key Fob Inputs/Wireless device can
be connected to the DMP Controller.
DMP XR500N Integration User Guide
5-13
DMP Controller-Triggers Tab
DMP Controller-Triggers Tab
C•CURE 9000 uses triggers, which are configured procedures for activating
events based on the properties of an object. A trigger automatically executes a
specified action when a particular predefined condition occurs. Figure 5-9 on
page 5-14 shows the DMP Controller Triggers tab.
Figure 5-9: DMP Controller-Triggers Tab
DMP Controller-Triggers Devices Tab Definitions
Table 5-5 on page 5-15 provides definitions for the fields on the DMP
Controller Triggers tab.
5-14
DMP XR500N Integration User Guide
DMP Controller-Triggers Tab
Table 5-5: DMP Controller-Triggers Tab Definition
Property
Value
Action
Armed Status
Armed
Activate Event
Disarmed
Partially Armed
Forced Armed
Online Status
Online
Activate Event
Synchronization Status
Start Synchronizing
Activate Event
Synchronizing
Finished Synchronizing
Add and Remove buttons are used to append and remove triggers to and
from an object.
• Property: Properties on which triggers can be added
• Value : Values that a property can take up
• Action : Actions need to be taken by the trigger
• Details : Event to be activated by the trigger
To define a Trigger for DMP Controller
1. From the DMP Controller dialog box, navigate to the Triggers tab.
2. Click Add in the Triggers tab to create a new trigger.
3. Click ..........within the Property column to open the DMP Input Triggers
dialog box showing the properties available for the Input.
4. Click a Property to select it and add it to the Property column.
5. Click within the Value column to display a drop-down list. Click the
value that you want to include as a parameter for the trigger to add it to
the column.
DMP XR500N Integration User Guide
5-15
DMP Controller-Triggers Tab
6. Click within the Action column to display a drop-down list of valid
actions. Only Activate Event is available at this time. When you select an
action, the lower pane in the Triggers dialog box displays an event field
for you to define the action details.
7. Click ......... to open the Event dialog box. Select an event that you want to
associate with the trigger. Once you define the action details, the Details
column displays information about how the action has been configured.
8. Click Save and Close to save the DMP Input with the trigger you
configured.
To Remove a Trigger
1. From the DMP Controller dialog box, navigate to the Trigger tab.
2. Use .......... to select the row in the Trigger table for the trigger you want to
remove.
3. Click Remove.
4. Click Save and Close to save and exit.
5-16
DMP XR500N Integration User Guide
DMP Controller-Groups Tab
DMP Controller-Groups Tab
The Groups tab contains the list of groups to which the Controller belongs.
NOTE
The Groups tab is not present for a new DMP Controller, that is, a
controller which is not yet saved cannot be added to any Group. A Groups
tab is present only after the first DMP Controller is created and saved.
Figure 5-10: DMP Controller-Groups Tab
DMP Controller-Groups Tab Definitions
Table 5-6 on page 5-18 provides definitions for the fields on the Controller
Groups tab.
DMP XR500N Integration User Guide
5-17
DMP Controller-Groups Tab
Table 5-6: DMP Controller-Groups Tab Definitions
Field
Description
Name
Enter a unique name up to 100 characters
long for the DMP Controller.
Description
Enter a general comment about the
Controller.
To Add a DMP Controller to a Group
1. In the Navigation pane of a Administration Workstation, click Hardware
to open the Hardware pane.
2. Select Controller from the Hardware pane drop-down list.
3. Click .... to open a Dynamic View showing all DMP Intrusion Areas.
4. Right-click the DMP Intrusion Area in the list that you want to add to a
group and select Add To Group from the context menu.
To Remove an DMP Controller from a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select Group from the Configuration pane drop-down list.
3. Click .... to open a Dynamic View showing all Groups.
4. Open the Group to which the required DMP Controller belongs by
double clicking on it.
5. Select the DMP Controller from the General Tab and click Remove.
6. Click Save and Close to save the DMP Intrusion Area with the group you
configured.
5-18
DMP XR500N Integration User Guide
DMP Controller-Status Tab
DMP Controller-Status Tab
As shown in Figure 5-11 on page 5-19, the DMP Controller Status tab
provides read-only status information about the DMP Controller.
Figure 5-11: : DMP Controller-Status Tab
DMP XR500N Integration User Guide
5-19
DMP Controller-Status Tab
DMP Controller-Status Tab Definitions
The Status field displays the current status information, for example, Online
Status and Armed Status. Table 5-7 on page 5-20 provides DMP Controller
Status tab definitions.
Table 5-7: DMP Controller-Status Tab Definitions
Field
Values
Definitions
Online Status
Online
The DMP Controller is
online.
Offline
The DMP Controller is
offline.
Disabled
The DMP Controller is
unavailable now.
Armed
All areas in the DMP
controller are armed.
Disarmed
All areas in the DMP
Controller are disarmed.
Partially Armed
Some areas in the DMP
Controller are armed.
Forced Armed
The System is force armed.
Armed Status
5-20
Field
Value
App Version
Application version of the controller
Version date
Date of the application version
MAC Address
MAC address of the controller
Serial Number
Serial number of the controller
DMP XR500N Integration User Guide
DMP Controller-State Images Tab
DMP Controller-State Images Tab
The State Images tab, shown in Figure 5-12 on page 5-21, provides a means to
change the default images used to indicate the DMP Controller states on the
Monitoring Station.
Figure 5-12: DMP Controller-State Images Tab
From the DMP Controller State Images tab, you can change the images that
appear in the Monitoring Station to represent DMP Controllers.
To Customize DMP Controller State Images
1. From the DMP Controller State Images tab, double-click the existing
image. A Windows Open dialog box appears, allowing you to browse for
a folder in which you have placed replacement images.
2. When you locate the replacement image, select it and click Open to
replace the default image with this image.
3. When you have replaced the image, click Save and Close to save the new
configuration of the DMP Controller.
DMP XR500N Integration User Guide
5-21
DMP Controller-State Images Tab
5-22
DMP XR500N Integration User Guide
6
DMP-Intrusion Area
This chapter provides information about DMP Intrusion Area Editor.
This chapter covers
DMP Intrusion Area-Overview............................................................................... 6-2
DMP Intrusion Area-General Tab.......................................................................... 6-3
DMP Intrusion Area-Zones Tab ............................................................................. 6-5
DMP Intrusion Area-Triggers ................................................................................. 6-7
DMP Intrusion Area-Groups ................................................................................... 6-9
DMP Intrusion Area-Status ................................................................................... 6-11
DMP Intrusion Area-State Images ....................................................................... 6-13
Arming and Disarming an Area from Monitoring Station................................... 6-14
DMP XR500N Integration User Guide
6-1
DMP Intrusion Area-Overview
DMP Intrusion Area-Overview
You can organize DMP Inputs into Intrusion Areas. Intrusion Areas let you
refer to several DMP inputs using one name that you specify. You can
configure DMP Inputs that activate Intrusion Areas, such as, DMP Inputs
activating events that specify actions for Intrusion Areas.
For example, if you want to arm certain DMP Inputs for specific times, you
can group them together in an Intrusion Area and apply the desired schedule
for them at once, using an event, rather than setting up schedules for each
input separately.
NOTE
When you arm an Intrusion Area, you are arming the individual objects in
it, not the group itself. A group has no status, but the objects that compose
it do.
DMP inputs in DMP XR500N Integration are also known as Zones.
6-2
DMP XR500N Integration User Guide
DMP Intrusion Area-General Tab
DMP Intrusion Area-General Tab
Table 6-1 on page 6-4 provides definitions for the fields on the DMP Intrusion
Area General tab
Figure 6-1: DMP Intrusion Area-General Tab
DMP XR500N Integration User Guide
6-3
DMP Intrusion Area-General Tab
DMP Intrusion-Area General Tab Definitions
Table 6-1 on page 6-4 provides definitions for the fields on the DMP
Intrusion-Area General tab.
Table 6-1: DMP Intrusion-Area General Tab Definitions
Field
Description
Name
Displays the name of the Area.
Description
Enter a general comment about the Area.
Identification
6-4
Controller
Displays the Controller name.
Area Number
Displays the Area Number.
Area Account Number
Displays the Area Account number.
DMP XR500N Integration User Guide
DMP Intrusion Area-Zones Tab
DMP Intrusion Area-Zones Tab
You can add multiple DMP Inputs to a DMP Intrusion Area using Add.
To remove DMP Input from a DMP Intrusion Area, you can use Remove.
DMP Inputs can be both onboard and Inputs on secondary devices as shown
in Figure 6-2 on page 6-5. See “DMP Intrusion-Area General Tab Definitions”
on page 6-4.
Figure 6-2: DMP Intrusion Area-Zones Tab
DMP XR500N Integration User Guide
6-5
DMP Intrusion Area-Shifts
DMP Intrusion Area-Shifts
Figure 6-3 on page 6-6 displays the DMP Intrusion Area Shifts tab.
Figure 6-3: DMP Intrusion Area-Shifts Tab
6-6
DMP XR500N Integration User Guide
DMP Intrusion Area-Triggers
DMP Intrusion Area-Triggers
You can configure triggers in the Triggers tab. Figure 6-4 on page 6-7 shows
the DMP Intrusion Area Triggers tab information.
Figure 6-4: DMP Intrusion Area-Triggers Tab
DMP XR500N Integration User Guide
6-7
DMP Intrusion Area-Triggers
DMP Intrusion Area-Triggers Tab Definitions
Table 6-2 on page 6-8 provides definitions for the fields on the DMP Intrusion
Area Triggers tab.
Table 6-2: DMP Intrusion Area-Triggers Tab Definition
Property
Value
Action
Armed Status
Armed
Activate Event
Disarmed
Partially Armed
Forced Armed
Late Status
No Abnormal
Activate Event
Condition
Late to Close
Schedule Status
In Schedule
Not In Schedule
6-8
DMP XR500N Integration User Guide
Activate Event
DMP Intrusion Area-Groups
DMP Intrusion Area-Groups
The groups are used for organizing C•CURE 9000 objects and are created in
the Configuration pane. You can configure groups of controllers, inputs,
outputs and other hardware security objects as shown in Figure 6-5 on
page 6-9.
Figure 6-5: DMP Intrusion Area-Groups Tab
DMP Intrusion Area-Groups Tab Definitions
Table 6-3 on page 6-9 provides definitions for the fields on the Intrusion Area
Groups tab.
Table 6-3: DMP Intrusion Area-Groups Tab Definitions
Field
Description
Name
Enter a unique name up to 100 characters
long for the DMP Controller.
DMP XR500N Integration User Guide
6-9
DMP Intrusion Area-Groups
Table 6-3: DMP Intrusion Area-Groups Tab Definitions, continued
Field
Description
Description
Enter a general comment about the
Controller.
To Add an DMP Intrusion Area to a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select DMP Intrusion Area from the Hardware pane drop-down list.
3. Click ..... to open a Dynamic View showing all DMP Intrusion Areas.
4. Right-click the DMP Intrusion Area in the list that you want to add to a
group and select Add To Group from the context menu.
To Remove an DMP Intrusion Area from a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select Group from the Configuration pane drop-down list.
3. Click ..... to open a Dynamic View showing all Groups.
4. Open the Group to which the required DMP Intrusion Area belongs by
double-clicking on it.
5. Select the DMP Intrusion Area from the General tab and Click Remove.
6. Click Save and Close to save the DMP Intrusion Area with the group you
configured.
6-10
DMP XR500N Integration User Guide
DMP Intrusion Area-Status
DMP Intrusion Area-Status
As shown in Figure 6-6 on page 6-11, DMP Intrusion Area Status tab provides
read-only status information about the DMP Intrusion Area.
Figure 6-6: DMP Intrusion Area-Status Tab
DMP XR500N Integration User Guide
6-11
DMP Intrusion Area-Status
DMP Intrusion Area-Status Tab Definitions
Table 6-4 on page 6-12, provides definitions for the fields on the Intrusion
Area Status tab.
Table 6-4: DMP Intrusion Area-Status tab settings
Property
Value
Action
Details
Armed Status
Armed
Activate Event
Event Details
Activate Event
Event Details
Activate Event
Event Details
Disarmed
Forced Arm
Late Status
No Abnormal
Condition
Late to Close
Schedule Status
In Schedule
Not In Schedule
6-12
DMP XR500N Integration User Guide
DMP Intrusion Area-State Images
DMP Intrusion Area-State Images
The State Images tab, shown in Figure 6-7 on page 6-13, provides a means to
change the default images used to indicate the DMP Intrusion Area states on
the Monitoring Station.
Figure 6-7: DMP Intrusion Area-State Images Tab
From the DMP Intrusion Area State Images tab, you can change the images
that appear in the Monitoring Station to represent DMP Intrusion Area.
To Customize DMP Intrusion Area State Images
1. From the DMP Intrusion Area State Images tab, double-click the existing
image. A Windows Open dialog box appears, allowing you to browse for
a folder in which you have placed replacement images.
2. When you locate the replacement image, select it and click Open to
replace the default image with this image.
3. When you have replaced the image, click Save and Close to save the new
configuration of the DMP Intrusion Area.
DMP XR500N Integration User Guide
6-13
Arming and Disarming an Area from Monitoring Station
Arming and Disarming an Area from Monitoring Station
To arm and disarm an area from monitoring station maps
1. Click Maps on Non Hardware Status panel. Status List-Maps dialog
opens.
2. Select a Map.
3. Right-click on the Map. Select Popup view, Map opens.
4. Select any DMP Intrusion Area configured in the Map.
5. Right-click on the DMP Intrusion Area.
6. Select Arm or Disarm.
To arm and disarm an area from monitoring station dynamic view
1. Click Dynamic View on Non Hardware Status panel. Status ListDynamic Views dialog opens.
2. Select a Dynamic View.
3. Right-click on the Dynamic View. Select Popup view, Dynamic View
opens.
4. Select a DMP Intrusion Area.
5. Right-click on the DMP Intrusion Area. Select Arm or Disarm.
To arm and disarm an area from monitoring station event messages
1. Select the Message from Area.
2. Right-click on the Message. Select Arm or Disarm.
6-14
DMP XR500N Integration User Guide
7
DMP-Input
This chapter provides information about DMP Input.
This chapter covers
DMP Inputs-Overview ............................................................................................. 7-2
DMP Input-General Tab .......................................................................................... 7-5
DMP Input-Triggers Tab.......................................................................................... 7-7
DMP Input-Groups Tab ......................................................................................... 7-11
DMP Input-Status Tab............................................................................................ 7-13
DMP Inputs-State Images ...................................................................................... 7-15
DMP XR500N Integration User Guide
7-1
DMP Inputs-Overview
DMP Inputs-Overview
DMP Inputs represent the physical interface in the DMP Controller. The DMP
Inputs editor provides related zone information. One controller can have up
to 574 inputs.
To Access an Input
1. Open the DMP Controller folder containing the DMP Controller to which
the Input you want to open belongs. See “To Access a Configured DMP
Controller” on page 5-2.
2. Open the Inputs folder by clicking to the left of the folder for Main Board
Inputs. For non-Main Board inputs, open a Secondary Device folder
containing the DMP Secondary Device to which the Input you want to
open belongs. Open the Inputs folder by clicking to the left of the folder.
3. Select the zone you want to open by double-clicking the Input icon or
name. The DMP Input editor opens with the General tab visible.
To Create a DMP Input
1. Expand the list of DMP controllers in the Hardware navigation pane.
2. Right-click the DMP Controller in which you want to create an input, and
select Edit.
3. The DMP Controller editor opens. Select Synchronize to update your
DMP Controller object with the latest input information from the DMP
hardware.
4. Click Save and Close to save and exit.
To Delete a DMP Input
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Input from the Hardware pane drop-down list.
7-2
DMP XR500N Integration User Guide
DMP Inputs-Overview
3. Click ..... to open a Dynamic View showing all DMP Input objects as
shown in Figure 7-1 on page 7-3.
Figure 7-1: DMP Inputs-Dynamic View
4. In the list, right-click the DMP Input object that you want to delete and
select Delete from the context menu. A message box appears stating "Are
you sure that you want to delete the selected DMP Input object?" as
shown in Figure 7-2 on page 7-3.
Figure 7-2: DMP Input Deletion
5. Click Yes in the message box to delete the DMP Input object.
To Configure a DMP Input
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Input from the Hardware pane drop-down list.
DMP XR500N Integration User Guide
7-3
DMP Inputs-Overview
3. Click .... to open a Dynamic View showing all DMP Input objects.
4. Double-click the DMP Input object in the list that you want to configure.
The DMP Input opens.
5. Type an optional description for the Input in the Description field.
6. Click the Enabled option to put the Input online.
7. You can click the Triggers tab to configure triggers for the DMP zone. See
“DMP Input-Triggers Tab” on page 7-7.
8. You can click the State Images tab to view the state images for DMP
Input. See “DMP Inputs-State Images” on page 7-15.
9. When you finish editing the DMP Input, click Save and Close to save the
configuration.
7-4
DMP XR500N Integration User Guide
DMP Input-General Tab
DMP Input-General Tab
As shown in Figure 7-3 on page 7-5 the DMP General tab shows the basic
information of the Input.
Figure 7-3: DMP Input-General Tab
DMP XR500N Integration User Guide
7-5
DMP Input-General Tab
DMP Input-General Tab Definitions
Table 7-1 on page 7-6 provides definitions for the fields on the DMP Input
General Tab.
Table 7-1: DMP Input-General Tab Definitions
Field
Description
Name
Displays the name of the Input.
Description
Enter a general comment about the Input.
Identification
Controller
Displays the Controller name.
Board
Displays the Interface board to which this
input is connected. In this case, it will be
Main Board or add-on device.
Type
Displays the type of input. It may be
Unknown, Tamper, Battery Low, Power
Failure, Printer, Wireless, Fire or Smoke,
Telephone Line.
Assigned to
Displays the object to which the input is
assigned. The object can be the controller.
Connection
Displays the input index/slot index of the
input.
Options
7-6
Send state changes to monitoring station
Select this option to send state changes to
monitoring station.
Send state changes to journal
Select this option to send state changes to
journal.
Supervised
Indicates if the Input is Supervised or not.
DMP XR500N Integration User Guide
DMP Input-Triggers Tab
DMP Input-Triggers Tab
You can configure triggers in the DMP Input Triggers tab. Figure 7-4 on
page 7-7 shows the DMP Input Trigger tab information.
Figure 7-4: DMP Input-Triggers Tab
DMP Input-Triggers Tab Definitions
Table 7-2 on page 7-7 provides definitions for the fields on the DMP Input
Triggers tab.
Table 7-2: DMP Input-TriggersTab Definitions
Field
Description
Add
Click Add in the Triggers tab to create a
new trigger.
Remove
Click Remove in the Triggers tab to delete
a new trigger.
DMP XR500N Integration User Guide
7-7
DMP Input-Triggers Tab
Table 7-2: DMP Input-TriggersTab Definitions, continued
Field
Description
Property
Click within the Property column and then
click ......... . The Property browser opens
displaying the properties available for the
Controller. Click a property to select it and
add it to the column.
Value
Click within the Value column to display a
drop-down list of values associated with the
property that you have selected. Click the
value you want to include as a parameter
for the trigger to assign it to the column.
Action
Click within the Action column to display a
drop-down list of valid actions.
Click on an action that you want to include
as a parameter for the trigger to add it to
the column.
Details
Displays details about how the Action was
configured.
Schedule
Only the Always Schedule is available for
DMP Input Triggers.
DMP Input-Triggers Tab Settings
Table 7-3 on page 7-8 provides settings for the fields on the DMP Input
Triggers tab.
Table 7-3: DMP Input-Triggers Tab Settings
Property
Value
Action
Details
Active Status
Inactive
Activate Event
Event Details
Activate Event
Event Details
Active
Input HW Status
Open
Short
Inactive
Active
7-8
DMP XR500N Integration User Guide
DMP Input-Triggers Tab
Table 7-3: DMP Input-Triggers Tab Settings, continued
Property
Value
Action
Details
Supervision
Status
Normal
Activate Event
Event Details
Open
Short
Bypassed
Low Battery
Missing
Trouble
Uninitialized
To Define a Trigger for DMP Input
1. From the DMP Input dialog box, navigate to the Triggers tab.
2. Click Add in the Triggers tab to create a new trigger.
3. Click ...........within the Property column to open the DMP Input Triggers
dialog box showing the properties available for the Input.
4. Click a Property to select it and add it to the Property column.
5. Click within the Value column to display a drop-down list. Click the
value that you want to include as a parameter for the trigger to add it to
the column.
6. Click within the Action column to display a drop-down list of valid
actions. Only Activate Event is available at this time. When you select an
action, the lower pane in the Triggers dialog box displays an event field
for you to define the action details.
7. Click ........... to open the Event dialog box. Select an event that you want to
associate with the trigger. Once you define the action details, the Details
column displays information about how the action has been configured.
8. Click Save and Close to save the DMP Input with the trigger you
configured.
DMP XR500N Integration User Guide
7-9
DMP Input-Triggers Tab
To Remove a Trigger
1. From the DMP Input dialog box, navigate to the Triggers tab.
2. Use .......... to select the row in the Triggers table for the trigger you want
to remove.
3. Click Remove.
4. Click Save and Close to save and exit.
7-10
DMP XR500N Integration User Guide
DMP Input-Groups Tab
DMP Input-Groups Tab
Inputs are added to Groups to apply actions on a Group which is much
simpler than applying actions to individual objects. The Groups tab provides
information about the group to which the current input belongs.
Figure 7-5: DMP Input-Groups Tab
DMP Input-Groups Tab Definitions
Table 7-4 on page 7-11 provides definitions for the fields on the Input Groups
tab.
Table 7-4: DMP Input-Groups Tab Definitions
Field
Description
Name
Enter a unique name up to 100 characters
long for the DMP Controller.
Description
Enter a general comment about the
Controller.
DMP XR500N Integration User Guide
7-11
DMP Input-Groups Tab
To Add an DMP Input to a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select DMP Input from the Hardware pane drop-down list.
3. Click .... to open a Dynamic View showing all DMP Inputs.
4. Right-click the DMP input in the list that you want to add to a group and
select Add To Group from the context menu.
To Remove an DMP Input from a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select Group from the Configuration pane drop-down list.
3. Click .... to open a Dynamic View showing all Groups.
4. Open the Group to which the required DMP Input belongs by double
clicking on it.
5. Select the DMP Input from the General Tab and Click Remove.
6. Click Save and Close to save the DMP Input with the group you
configured.
7-12
DMP XR500N Integration User Guide
DMP Input-Status Tab
DMP Input-Status Tab
As shown in Figure 7-6 on page 7-13, the DMP Input Status tab provides
read-only status information about the DMP zone.
Figure 7-6: DMP Input-Status Tab
DMP XR500N Integration User Guide
7-13
DMP Input-Status Tab
DMP Input-Status Tab Definitions
Table 7-5 on page 7-14 provides definitions for the fields on the DMP Input
Status tab.
Table 7-5: DMP Input-Status Tab Settings
Property
Value
Definations
Active Status
Active
Zone is active.
Inactive
Zone is inactive.
Open
Physical status of zone is
open.
Closed
Physical status of zone is
shorted.
Open
Zone physical status is
open.
Closed
Zone physical status is
shorted.
Bypassed
Zone is bypassed.
Low Battery
Zone Battery is low.
Missing
Zone not configured.
Trouble
Trouble in zone.
Hardware Status
Supervision status
7-14
DMP XR500N Integration User Guide
DMP Inputs-State Images
DMP Inputs-State Images
The State Images tab, shown in Figure 7-7 on page 7-15, provides a means to
change the default images used to indicate the DMP Input states on the
Monitoring Station.
Figure 7-7: DMP Input Area-State Images Tab
From the DMP Input State Images tab, you can change the images that appear
in the Monitoring Station to represent DMP Input.
To Customize DMP Input State Images
1. From the DMP Input State Images tab, double-click the existing image. A
Windows Open dialog box appears, allowing you to browse for a folder
in which you have placed replacement images.
2. When you locate the replacement image, select it and click Open to
replace the default image with this image.
3. When you have replaced the image, click Save and Close to save the new
configuration of the DMP Input.
DMP XR500N Integration User Guide
7-15
DMP Inputs-State Images
7-16
DMP XR500N Integration User Guide
8
DMP-Output
This chapter provides information about DMP Output.
This chapter covers
DMP Outputs-Overview .......................................................................................... 8-2
DMP Output-General Tab ....................................................................................... 8-5
DMP Output-Groups Tab ........................................................................................ 8-7
DMP Output-Status Tab........................................................................................... 8-9
DMP Output-State Images ..................................................................................... 8-11
DMP XR500N Integration User Guide
8-1
DMP Outputs-Overview
DMP Outputs-Overview
Outputs are system relays. The system may use these outputs to control door
access, interior and exterior lighting, heating, air conditioning, or other
appliances.
To Access an Output
1. Open the DMP Controller folder containing the DMP Controller to which
the output you want to open belongs. See “To Access a Configured DMP
Controller” on page 5- 2.
2. Open the Outputs folder by clicking to the left of the folder for Main
Board outputs. For non-Main Board outputs, open the Secondary Device
folder containing the DMP Secondary Device to which output you want
to open belongs. Open the Outputs folder by clicking to the left of the
folder.
3. Select the output you want to open by double-clicking the Output icon or
name. The DMP Output editor opens with the General tab visible.
To Create a DMP Output
1. Expand the list of DMP controllers in the Hardware navigation pane.
2. Right-click the DMP Controller in which you want to create an output ,
and select Edit.
3. The DMP Controller editor opens. Select Synchronize to update your
DMP Controller object with the latest output information from the DMP
hardware.
4. Click Save and Close to save and exit.
To Delete a DMP Output
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Output from the Hardware pane drop-down list.
8-2
DMP XR500N Integration User Guide
DMP Outputs-Overview
3. Click ..... to open a Dynamic View showing all DMP Output objects as
shown in Figure 8-1 on page 8-3.
Figure 8-1: DMP Output-Dynamic View
4. In the list, right-click the output object that you want to delete and select
Delete from the context menu. A message box appears stating "Are you
sure that you want to delete the selected DMP Output object?" as shown
in Figure 8-2 on page 8-3.
Figure 8-2: DMP Output deletion
5. Click Yes in the message box to delete the output object.
DMP XR500N Integration User Guide
8-3
DMP Outputs-Overview
To Configure a DMP Output
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Output from the Hardware pane drop-down list.
3. Click ..... to open a Dynamic View showing all DMP output objects.
4. Double-click the DMP output in the list that you want to configure. The
DMP Output Editor opens.
5. Type an optional description for the Output in the Description field.
6. Click the Enabled option to put the output online.
7. You can click the Triggers tab to configure triggers for the DMP output.
8. You can click the State Images tab to view the state images for DMP
Output. See “DMP Output-State Images” on page 8- 11.
9. When you finish editing the DMP output, click Save and Close to save the
configuration.
8-4
DMP XR500N Integration User Guide
DMP Output-General Tab
DMP Output-General Tab
As shown in Figure 8-3 on page 8-5, the DMP General tab shows the basic
information of the Output.
Figure 8-3: DMP Output-General Tab
DMP XR500N Integration User Guide
8-5
DMP Output-General Tab
DMP Output General Tab Definitions
Table 8-1 on page 8-6 provides definitions for the fields on the DMP Output
General tab.
Table 8-1: DMP Output-General Tab Definitions
Field
Description
Name
Displays the name of the Output.
Description
Enter a general comment about the Output.
Identification
Controller
Displays the Controller name.
Board
Displays the Interface board to which this
output is connected. In this case, it will be
the Main Board or add-on device.
Type
Displays the type of output. It is usually
General Purpose Output.
Assigned to
Displays the object to which this device is
assigned. It can be the Controller.
Connection
Displays the output index/slot index of the
output.
Options
8-6
Send state changes to monitoring station
Select this option to send state changes to
the Monitoring Station.
Send state changes to journal
Select this option to send state changes to
the journal.
DMP XR500N Integration User Guide
DMP Output-Groups Tab
DMP Output-Groups Tab
As shown in Figure 8-4 on page 8-7, the DMP Groups tab shows the basic
information of the Output.
Figure 8-4: DMP Output-Groups Tab
DMP Output-Groups Tab Definitions
Table 8-2 on page 8-7 provides definitions for the fields on the DMP Output
Triggers tab.
Table 8-2: DMP Output-Groups Tab Definitions
Field
Description
Name
Enter a unique name up to 100 characters
long for the DMP Controller.
Description
Enter a general comment about the
Controller.
DMP XR500N Integration User Guide
8-7
DMP Output-Groups Tab
To Add an DMP Output to a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select DMP Output from the Hardware pane drop-down list.
3. Click ..... to open a Dynamic View showing all DMP Outputs.
4. Right-click the DMP Output in the list that you want to add to a group
and select Add To Group from the context menu.
To Remove an DMP Output from a Group
1. In the Navigation pane of the Administration Workstation, click
Hardware to open the Hardware pane.
2. Select Group from the Configuration pane drop-down list.
3. Click ..... to open a Dynamic View showing all Groups.
4. Open the Group to which the required DMP Output belongs by double
clicking on it.
5. Select the DMP Output from the General Tab and click Remove.
6. Click Save and Close to save the DMP Output with the group you
configured.
8-8
DMP XR500N Integration User Guide
DMP Output-Status Tab
DMP Output-Status Tab
As shown in Figure 8-5 on page 8-9, DMP Output Status tab provides readonly status information about the DMP Output.
Figure 8-5: DMP Output-Status Tab
DMP XR500N Integration User Guide
8-9
DMP Output-Status Tab
DMP Output-Status Tab Definitions
Table 8-3 on page 8-10 provides definitions for the fields on the DMP Output
Status tab.
Table 8-3: DMP Output-Status Tab Definations
8-10
Property
Value
Definitions
Active Status
Active
Output is active. Relay is
closed.
Inactive
Output is inactive. Relay is
open.
Pulsed
Output will be alternatively ON
or OFF for a predetermined
time.
DMP XR500N Integration User Guide
DMP Output-State Images
DMP Output-State Images
The DMP Output State Images tab, shown in Figure 8-6 on page 8-11,
provides a means to change the default images used to indicate the DMP
Output states on the Monitoring Station.
Figure 8-6: DMP Output-State Images Tab
From the DMP Output State Images tab, you can change the images that
appear in the Monitoring Station to represent DMP Output.
To Customize DMP Output State Images
1. From the DMP Output State Images tab, double-click the existing image.
A Windows Open dialog box appears allowing you to browse for a folder
in which you have placed replacement images.
2. When you locate the replacement image, select it and click Open to
replace the default image with this image.
3. When you have replaced the image, click Save and Close to save the DMP
Outputs new configuration.
DMP XR500N Integration User Guide
8-11
DMP Output-State Images
8-12
DMP XR500N Integration User Guide
9
DMP Device Editor
This chapter provides information about DMP Device Editor.
This chapter covers
DMP Device-Overview............................................................................................. 9-2
DMP Secondary Device-General Tab.................................................................... 9-5
DMP Secondary Device-Inputs Tab....................................................................... 9-7
DMP Secondary Device-Outputs Tab.................................................................... 9-8
DMP XR500N Integration User Guide
9-1
DMP Device-Overview
DMP Device-Overview
DMP Device object is used to configure add-on, supervised, hardware devices
connected to the DMP Controller on a keypad bus, a LX bus, or a wireless
receiver.
NOTE
A device is known as a Secondary Device in C•CURE 9000 and DMP
XR500N integration system.
To Access a Secondary Device
1. Open the DMP Controller folder containing the DMP Controller to which
the device you want to open belongs. See “To Access a Configured DMP
Controller” on page 5- 2
2. Open the Devices folder by clicking to the left of the folder.
NOTE
After you synchronize with a controller, a device sub-folder named
Devices is automatically created. All devices belonging to this controller
are included in this folder. They are created only if Inputs belonging to
those devices have been configured.
3. Select the device you want to open by double-clicking the device icon or
name. The DMP Device editor opens with the General tab visible.
To Create a DMP Secondary Device
1. Expand the list of DMP controllers in the Hardware navigation pane.
2. Right-click the DMP Controller in which you want to create a device and
select Edit.
3. The DMP Controller editor opens. Select Synchronize to update your
DMP controller object with the latest device information from the DMP
hardware.
4. Click Save and Close to save and exit.
9-2
DMP XR500N Integration User Guide
DMP Device-Overview
To Delete a DMP Secondary Device
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP Device from the Hardware pane drop-down list.
3. Click ....... to open a Dynamic View showing all DMP device objects as
shown in Figure 9-1 on page 9-3.
Figure 9-1: DMP Device-Dynamic View
DMP XR500N Integration User Guide
9-3
DMP Device-Overview
4. In the list, right-click the device that you want to delete and select Delete
from the context menu. A message box appears stating "Are you sure that
you want to delete the selected DMP Secondary Device object?" as shown
in Figure 9-2 on page 9-4.
Figure 9-2: DMP Device Deletion
5. Click Yes in the message box to delete the device.
9-4
DMP XR500N Integration User Guide
DMP Secondary Device-General Tab
DMP Secondary Device-General Tab
As shown in Figure 9-3 on page 9-5, the DMP General tab shows the basic
information of the device.
Figure 9-3: DMP Device-General Tab
DMP XR500N Integration User Guide
9-5
DMP Secondary Device-General Tab
DMP Secondary Device General Tab Definitions
Table 9-1 on page 9-6 provides definitions for the fields on the DMP
Secondary Device General tab.
Table 9-1: DMP Secondary Device-General Tab Definitions
Field
Description
Name
Displays the name of the secondary device.
Description
Enter a general comment about the
secondary device.
Board Location
9-6
Controller
Displays the Controller name.
Device Number
Displays the device number.
Bus Type
Displays the type of device. It may be a
Keypad, an LX Bus_Wireless, or wireless.
DMP XR500N Integration User Guide
DMP Secondary Device-Inputs Tab
DMP Secondary Device-Inputs Tab
Figure 9-4 on page 9-7 shows the information displayed on the DMP
Secondary Device Inputs tab.
Figure 9-4: DMP Secondary Device-Inputs Tab
DMP Secondary Device-InputsTab Definitions
Table 9-2 on page 9-7 provides definitions for the fields on the DMP
Secondary Device Inputs tab.
Table 9-2: DMP Secondary Device-Inputs Tab Definition
Field
Description
Create all inputs
If the checkbox is enabled all the Inputs on
DMP Secondary Device are enabled and
their messages can be seen on Monitoring
Station.
Delete all inputs
Deletes all the Secondary Device inputs if it
is checked.
DMP XR500N Integration User Guide
9-7
DMP Secondary Device-Outputs Tab
DMP Secondary Device-Outputs Tab
Figure 9-5 on page 9-8 displays the Secondary Devices Outputs tab.
Figure 9-5: DMP Secondary Device-Outputs Tab
9-8
DMP XR500N Integration User Guide
DMP Secondary Device-Outputs Tab
DMP Secondary Device-OutputsTab Definitions
Table 9-3 on page 9-9 provides definitions for the fields on the DMP
Secondary Device Outputs tab.
Table 9-3: DMP Secondary Device-Outputs Tab Definition
NOTE
Field
Description
Create All Outputs
If the checkbox is enabled, all the outputs
on the DMP Secondary Device are enabled
and their messages can be seen on the
Monitoring Station
Delete All Outputs
Deletes all the Secondary Device outputs if
it is checked.
Keypad Bus Devices do not have outputs, and therefore, do not have an Outputs tab
DMP XR500N Integration User Guide
9-9
DMP Secondary Device-Outputs Tab
9-10
DMP XR500N Integration User Guide
10
DMP User Profile
This chapter provides information about DMP User Profile.
This chapter covers
DMP User Profile-Overview.................................................................................. 10-2
DMP User Profile-General Tab............................................................................. 10-5
DMP User Profile-Menu Option Tab .................................................................. 10-7
DMP User Profile-Shifts Tab............................................................................... 10-10
DMP User Profile-C•CURE Personnel Tab...................................................... 10-11
DMP XR500N Integration User Guide
10-1
DMP User Profile-Overview
DMP User Profile-Overview
User Profiles define the authority of each user code in the system.
To Access a User Profile
1. Open the DMP Controller folder containing the DMP Controller to which
the User Profile you want to open belongs. See “To Access a Configured
DMP Controller” on page 5- 2
2. Open the User Profile folder by clicking to the left of the folder.
3. Select the user profile you want to open by double-clicking the User
Profile icon or name. The DMP User Profile editor opens with the
General tab visible.
To Create a DMP User Profile
1. Expand the list of DMP controllers in the Hardware navigation pane.
2. Right-click the DMP Controller in which you want to create a User Profile,
and select Edit.
3. The DMP Controller editor opens. Select Synchronize to update your
DMP controller object with the latest input information from the DMP
hardware.
4. Click Save and Close to save and exit.
To Delete a DMP User Profile
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP User Profile from the Hardware pane drop-down list.
3. Click ....... to open a Dynamic View showing all DMP User Profile objects
as shown in Figure 10-1 on page 10-3.
10-2
DMP XR500N Integration User Guide
DMP User Profile-Overview
Figure 10-1: DMP User Profile-Dynamic View
4. In the list, right-click the User Profile that you want to delete and select
Delete from the context menu. A message box appears stating "Are you
sure that you want to delete the selected DMP User Profile object?"as
shown in Figure 10-2 on page 10-3.
Figure 10-2: DMP User Profile Deletion
5. Click Yes in the message box to delete the user profile object.
DMP XR500N Integration User Guide
10-3
DMP User Profile-Overview
To Configure a DMP User Profile
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP User Profile from the Hardware pane drop-down list.
3. Click ...... to open a Dynamic View showing all DMP User Profile objects.
4. Double-click the DMP User Profile in the list that you want to configure.
The DMP User Profile opens.
5. Type an optional description for the User Profile in the Description field.
6. You can click the Menu Option tab to view functions to which you have
access. See “DMP User Profile-Menu Option Tab” on page 10- 7.
7. You can click the Shifts tab to view the time schedules that the User Code
operates for door access and disarming. See “DMP Input-Status Tab” on
page 7- 13.
8. You can click the C•CURE Personnel tab to view the corresponding
C•CURE Personnel of the DMP Users. See “DMP User Profile-C•CURE
Personnel Tab” on page 10- 11.
9. When you finish editing the DMP User Profile, click Save and Close to
save the configuration.
10-4
DMP XR500N Integration User Guide
DMP User Profile-General Tab
DMP User Profile-General Tab
As shown in Figure 10-3 on page 10-5, the General tab shows the basic
information of the User Profile.
Figure 10-3: DMP User Profile-General Tab
DMP XR500N Integration User Guide
10-5
DMP User Profile-General Tab
DMP User Profile-General Tab Definitions
Table 10-1 on page 10-6 provides definitions for the fields on the DMP User
Profile General tab.
Table 10-1: DMP User Profile-General Tab Definitions
Field
Description
Name
Displays the name of the User Profile.
Description
Enter a general comment about the User
Profile.
Identification
Controller
Displays the Controller name.
Profile Number
Each profile may be assigned a unique
number From 1 to 99.
Re-arm Delay
Re-Arm Delay allows the entry of 0 to 250
minutes, to be used to delay automatic
rearming when the user disarms an area
outside of the schedule. If zero is selected,
the rearming occurs based on permanent
programming in the controller. Re-arm
Delay is also used to delay a late-to-close
message to the Central Station when the
Controller does not use automatic arming.
Permissions
10-6
Arm/Disarm
All the areas are listed. The Armed areas
are checked.
Output Groups
Displays the output group for every user
profile.
DMP XR500N Integration User Guide
DMP User Profile-Menu Option Tab
DMP User Profile-Menu Option Tab
You can view the Menu Options tab in the DMP User Profile. Figure 10-4 on
page 10-7 shows the DMP User Profile Menu Option tab information.
Figure 10-4: DMP User Profile-Menu Option Tab
DMP User Profile-Menu Option Tab Definitions
Table 10-2 on page 10-7 provides definitions for the fields on the DMP User
Profile tab.
Table 10-2: DMP User Profile-Menu Option Tab Descriptions
Menu Option
Description
Alarm Silence
Silences an alarm bell or siren.
Armed Areas
Displays the name of any areas in the
system that is currently in the armed state.
Door Access
Momentarily opens the keypad door lock
relay.
DMP XR500N Integration User Guide
10-7
DMP User Profile-Menu Option Tab
Table 10-2: DMP User Profile-Menu Option Tab Descriptions, continued
10-8
Menu Option
Description
Outputs On/off
Allows you to turn ON or OFF any of the
outputs described in the System Setup
section of this guide.
Sensor Reset
Resets smoke or glass break detectors that
have latched due to an alarm condition.
Zone Status
Allows you to see if a zone is either armed,
bypassed, in alarm, open, or shorted.
Bypass Zone
Allows you to bypass a zone or reset an
already bypassed zone.
Zone Monitor
Allows you to add or remove a zone from
the monitor mode.
System Status
Displays the current condition of the system
AC power, backup battery, and optional
controller tamper.
System Test
Tests the system siren, communication to
the Central Station, and backup battery on
all XR500N Series and XR100 Series
controllers. XR500N or XR500E controllers
allow additional panic zone testing.
User Profiles
Allows you to add, delete, or change user
profiles.
User Codes
Allows you to add, delete, or change user
codes.
Schedules
Allows you to add, remove, or change
system schedules.
Set Time
Allows you to change the Day, Date, or
Time that is currently programmed in the
system.
Display Events
Allows you to view or print the last 10,000
door accesses or 2,000 system events that
occurred on your system.
Service Required
Allows you to send a message to the
Central Station requesting service on the
alarm system.
Fire Drill
Allows you to test the system fire bells.
DMP XR500N Integration User Guide
DMP User Profile-Menu Option Tab
Table 10-2: DMP User Profile-Menu Option Tab Descriptions, continued
Menu Option
Description
Disarm Authority
This option alows users to disarm the area
which is armeds.
Schedule
If the user has Extend Schedule authority
by 2HR, 4HR, 6HR, or 8HR, it is displayed
at disarming. If the user does not make a
choice, then the Re-Arm Delay is used to
extend the schedule.
Temp Code
When this menu option is selected and
profile is assigned to a user code it is
diaplayed on the keyboard.
TEMP EXPIRE DATE: Enter the ending
date for the profile to expire. The default is
seven days from today. The system deletes
temporary users at 12:00 AM on the last
date.
Anti-Passback
Anti-Passback requires users to properly
exit (egress) an area they had previously
accessed. If they fail to exit through the
proper card reader location then, they are
not granted access on their next attempt. A
Failed to Exit message appears when a
user is assigned the anti-passback option,
attempts to re-enter an area which they did
not exit properly. The user must exit the
area through the proper door. If not
possible, your system administrator should
select the Forgive option in the User Codes
menu option.
Arm Authority
The authority to Arm areas. This option
provides authority to the users to arm
certain areas.
Easy Arm
When entering your code, Easy Arm/
Disarm allows you to automatically arm or
disarm all areas that are assigned to your
code.
Use Second Language
This options allows you to set the
programmed secondary user language to
display when the Easy Arm/Disarm option
is enabled and the user presents their
credential or enters their user code at the
Status List.
DMP XR500N Integration User Guide
10-9
DMP User Profile-Shifts Tab
DMP User Profile-Shifts Tab
As shown in Figure 10-5 on page 10-10, DMP Shifts tab provides read-only
status information about the DMP User Profile.
The Shifts tab defines the time schedules that the User Code operates for door
access and disarming. Selecting schedule 1, 2, 3, and/or 4 indicates operation
during the S1-S4 shift schedules. Selecting Allow Any Time from the menu
indicates the code operates any time, regardless of schedules. An
Unauthorized Entry message is sent to the Central Station if disarming occurs
outside the open/close schedule.
Figure 10-5: DMP User Profile-Shifts Tab
NOTE
10-10
All the controls except Name and Description are read-only.
DMP XR500N Integration User Guide
DMP User Profile-C•CURE Personnel Tab
DMP User Profile-C•CURE Personnel Tab
The C•CURE Personnel tab shows all the DMP users belonging to the
particular User Profile. If the user is linked to C•CURE Personnel, then the
corresponding DMP User-C•CURE Personnel mapping is shown.
Figure 10-6: DMP User Profile-C•CURE Personnel Tab
DMP XR500N Integration User Guide
10-11
DMP User Profile-C•CURE Personnel Tab
10-12
DMP XR500N Integration User Guide
11
DMP User
This chapter provides information about DMP User.
This chapter covers
DMP User-Overview ............................................................................................... 11-2
DMP User-General Tab .......................................................................................... 11-5
DMP XR500N Integration User Guide
11-1
DMP User-Overview
DMP User-Overview
Specific User Profiles may be assigned to individual users.
To Access a DMP User
1. Open the DMP Controller folder containing the DMP Controller to which
the user you want to access belongs. See “To Access a Configured DMP
Controller” on page 5- 2.
2. Open the User folder by clicking to the left of the folder.
3. Select the User you want to open by double-clicking the User icon or
name. The DMP User editor opens with the General tab visible.
To Create a DMP User Profile
1. Expand the list of DMP controllers in the Hardware navigation pane.
2. Right-click the DMP Controller in which you want to create a user and
select Edit.
3. The DMP Controller editor opens. Select Synchronize to update your
DMP Controller object with the latest user information from the DMP
hardware.
4. Click Save and Close to save and exit.
To Delete a DMP User
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP User from the Hardware pane drop-down list.
11-2
DMP XR500N Integration User Guide
DMP User-Overview
3. Click .... to open a Dynamic View showing all DMP user objects as shown
in Figure 11-1 on page 11-3.
Figure 11-1: DMP User-Dynamic View
4. In the list, right-click the user that you want to delete and select Delete
from the context menu. A message box appears stating "Are you sure that
you want to delete the selected DMP User object?" as shown in
Figure 11-2 on page 11-3.
Figure 11-2: DMP User Deletion
5. Click Yes in the message box to delete the user object.
To Configure a DMP User
1. In the Navigation pane of the Administration WorkStation, click
Hardware to open the Hardware pane.
2. Select DMP User from the Hardware pane drop-down list.
3. Click ..... to open a Dynamic View showing all DMP User Profile objects.
4. Double-click the DMP User in the list that you want to configure. The
DMP User editor opens.
DMP XR500N Integration User Guide
11-3
DMP User-Overview
5. Type an optional description for the User in the Description field.
6. You may link a C•CURE Personnel by clicking ......... on next to the
C•CURE Personnel field. Once a personnel object is selected, the name of
the user will be displayed in the C•CURE Personnel field.
7. Click Save and Close to save and exit.
11-4
DMP XR500N Integration User Guide
DMP User-General Tab
DMP User-General Tab
As shown in Figure 11-3 on page 11-5, the DMP User General tab shows the
basic information of the User.
Figure 11-3: DMP User-General Tab
DMP XR500N Integration User Guide
11-5
DMP User-General Tab
DMP User General Tab Definitions
Table 11-1 on page 11-6 provides definitions for the fields on the DMP User
General tab.
Table 11-1: DMP User-General Tab Definitions
Name
Description
Name
Displays the name of the DMP User.
Description
Enter a general comment about the DMP
User.
User Identification
11-6
User Number
Every user is numbered 1 through 9999.
This number identifies the user to the
system and is transmitted to the Central
Station when the user arms or disarms
areas.
Temp Date
When Temp Code is enabled for a user, the
Temp Expire Date/Temp Date becomes
available. This is the date the profile
expires.
User Profile Name
Displays the name of the User Profile
assigned to the DMP User.
C•CURE Personnel
Name of the C•CURE Personnel linked to
the DMP User.
DMP XR500N Integration User Guide
12
Event and Action
This chapter provides information about Event and Action.
This chapter covers
Event and Action-Overview................................................................................... 12-2
Information about DMP-Specific Actions .......................................................... 12-3
DMP-Specific Action Configuration Example................................................... 12-6
DMP XR500N Integration User Guide
12-1
Event and Action-Overview
Event and Action-Overview
In the C•CURE 9000 and DMP XR500N integration system, you can use an
event as a trigger object. Events are user-programmable components of the
C•CURE 9000 Administration System. For information about how to
configure an event, see the C•CURE 9000 Software Configuration Guide.
An actions is the object which is invoked by an event. Except for actions in
C•CURE 9000 system, the integration system also provides some defined
actions for you to configure an event. See “Information about DMP-Specific
Actions” on page 12- 3.
NOTE
12-2
If an Access Code is needed during the process of triggering an event, the
action configured for an event will not work.
DMP XR500N Integration User Guide
Information about DMP-Specific Actions
Information about DMP-Specific Actions
This section provides details of all the DMP-specific actions and target object
and how to configure the action and events.
As shown in Figure 12-1 on page 12-3, 13 DMP-specific actions are available.
Figure 12-1: DMP-Specific Actions List
Actions and Target Object
An action is a series of tasks or a single task to be executed when an event
occurs. Target Object is an object on which action is to be taken when an event
occurs.
DMP XR500N Integration User Guide
12-3
Information about DMP-Specific Actions
Table 12-1 on page 12-4 provides the actions and their target object
respectively.
Table 12-1: Actions and Target object
12-4
Action
Target Object
Explanation
DMP-Arm Intrusion Area
DMP Intrusion Area
This action Arms the
selected area. Bypassed
inputs are not activated.
DMP - Arm System
DMP Controller
This action arms all the
areas of the controller.
Bypassed inputs are not
activated.
DMP - Bypass Input
DMP Input
Bypasses the selected
input.
DMP - Continuous Pulse
Output
DMP Output
This action makes the
output alternate one
second ON and one
second OFF.
DMP - Disarm Intrusion
Area
DMP intrusion Area
This action Disarms the
selected area.
DMP - Disarm System
DMP Controller
This action disarms all
the areas of the
controller.
DMP - Force Arm Intrusion
Area
DMP Intrusion Area
This action arms the
area including all bad
zones in the areas.
DMP - Force arm System
DMP Controller
This action arms all the
areas of the controller
including the areas
containing the bad
zones.
DMP - Momentary Output
DMP Output
This action turns the
output ON only for 1
second.
DMP - Reset Input
DMP Input
This action resets an
Input if it is previously
Bypassed.
DMP XR500N Integration User Guide
Information about DMP-Specific Actions
Table 12-1: Actions and Target object
Action
Target Object
Explanation
DMP - Reset Sensor
DMP Controller
Resets smoke or glass
break detectors that
have latched due to an
alarm condition.
DMP - Silence Alarm
DMP Controller
Silences the alarm bells
or sirens during an
alarm.
DMP - Synchronize
DMP Controller
This action is used to
create C•CURE 9000
objects which are the
counterparts of the DMP
Panel Objects, such as
Inputs, Outputs, Users,
User Profiles, Areas, and
so forth that are
programmed in the
Panel.
DMP XR500N Integration User Guide
12-5
DMP-Specific Action Configuration Example
DMP-Specific Action Configuration Example
DMP-Arm Intrusion Area
This option arms an intrusion area. A group of zones will be armed because
an intrusion area is a collection of zones.
When you select DMP- Arm Intrusion Area in the Action drop-down list, the
related field and pane appears, as shown in Figure 12-2 on page 12-6.
Figure 12-2: Action Tab-DMP-Arm Intrusion Area
12-6
DMP XR500N Integration User Guide
DMP-Specific Action Configuration Example
Action Tab-DMP Intrusion Area Definitions
Table 12-2 on page 12-7 provides Action tab-DMP Intrusion Area definitions.
Table 12-2: Action Tab-DMP Intrusion Area Definitions
Field
Description
DMP Intrusion Area
Click ......... to open the DMP Intrusion Area
list. Select an Intrusion Area as the object
of this action.
DMP-Disarm Intrusion Area
This action is used to disarm an intrusion area. A group of zones will be
disarmed because an intrusion area is a collection of zones.
When you select DMP-Disarm Intrusion Area in the Action drop-down list,
the related field and pane appear as shown in Figure 12-3 on page 12-7.
Figure 12-3: Action Tab-DMP-Disarm Intrusion Area
DMP XR500N Integration User Guide
12-7
DMP-Specific Action Configuration Example
Action Tab-DMP Disarm Intrusion Area Definitions
Table 12-3 on page 12-8 provides Action tab-DMP Disarm Intrusion Area
definitions.
Table 12-3: Action Tab-Disarm DMP Intrusion Area Definitions
Field
Description
DMP Intrusion Area
Click ........ to open the DMP Intrusion Area
list. Select an Intrusion Area as the object
of this action.
DMP-Bypass Input
This action is used to skip the arming of a zone. When you select DMPBypass Input in the Action drop-down list, the related field and pane appear
as shown in Figure 12-4 on page 12-8.
Figure 12-4: Action Tab-DMP-Bypass Input
12-8
DMP XR500N Integration User Guide
DMP-Specific Action Configuration Example
Action Tab-DMP Bypass Input Definitions
Table 12-4 on page 12-9 provides Action tab-DMP Bypass Input definitions.
Table 12-4: Action Tab-DMP Bypass Input Definitions
Field
Description
DMP Input
Click ......... to open the DMP Input list.
Select a DMP Input as the object of this
action.
DMP-Reset Input
To reset is to clear the condition causing the trouble or fault alarm.
When you select DMP-Reset Input in the Action drop-down list, the related
field and pane appear as shown in Figure 12-5 on page 12-9.
Figure 12-5: Action Tab-DMPReset Input
DMP XR500N Integration User Guide
12-9
DMP-Specific Action Configuration Example
Action Tab-DMP Reset Input Definitions
Table 12-5 on page 12-10 provides Action tab-DMP Reset Input definitions.
Table 12-5: Action Tab-DMP Reset Input Definitions
Field
Description
DMP Input
Click ......... to open the DMP Input list.
Select a DMP Input as the object of this
action.
DMP-Synchronize
When you select DMP-Synchronize in the Action drop-down list, the related
field and pane appears, as shown in Figure 12-6 on page 12-10.
Figure 12-6: Action Tab-DMP-Synchronize
12-10
DMP XR500N Integration User Guide
DMP-Specific Action Configuration Example
Action Tab-DMP Synchronize Definitions
Table 12-6 on page 12-11 provides Action tab-DMP Synchronize definitions.
Table 12-6: Action Tab-DMP Synchronize Definitions
NOTE
Field
Description
DMP Controller
Click .......... to open the DMP Controller list.
Select a DMP Controller as the object of
this action.
"Synchronization" can be performed only when a connection is
established to a panel, that is, when the online status is "Online". If a
synchronization is initiated it cannot be started again until the previous
synchronization is finished.
DMP XR500N Integration User Guide
12-11
DMP-Specific Action Configuration Example
12-12
DMP XR500N Integration User Guide
13
Limitations
This chapter describes the limitations in C•CURE 9000 DMP XR500N
Integration.
This chapter covers
Limitations ................................................................................................................ 13-2
DMP XR500N Integration User Guide
13-1
Limitations
Limitations
13-2
„
System messages displayed in the Monitoring Station are similar to the
messages of the DMP Panel.
„
The Import/ Export function of the Controller will not export the
mapping of users in C•CURE Personnel to user profiles.
„
Due to the inherent nature of the DMP panel, there will be a delay in the
display of change of status and events. The delay depends on the number
of inputs /outputs /areas configured in the DMP panel.
„
To View the DMP Controllers in Monitoring Station you should configure
the Dynamic View.
„
User cannot delete the objects while synchronization.
„
Avoid modifying an object using “Set Property” and programming the
panel while synchronization is in progress.
„
Currently, the C•CURE 9000 DMP XR500N Integration does not support
installation with C•CURE 9000 on an Oracle database. Therefore, you
must install the software on a C•CURE 9000 system that is using SQL
Server 2005.
„
Non-Supervised inputs are being listed in Events (Bypass Input, Reset
Input actions) and also the input group having DMP Non-Supervised
inputs are listed in events.
„
End Time in Edit dialog for Synchronize Manual Actions is not
considered.
„
For pulse Manual Actions, Start and End time is not displayed in
Monitoring Station.
„
Occasionally, hardware tree in C•CURE 9000 Administration does not
get refreshed automatically hence, you have to refresh it manually.
„
When huge reports are executed for DMP objects, they might return an
error message and the resultant report will be incomplete.
„
If you are in MAS and in dynamic view, and if you try to point to
(ReadDataFrom field) any other SAS/other then the current MAS, it
gives an error stating that "Remote Server <Server Name> not available for
connection". Applicable only for C•CURE 9000 2.0 version
DMP XR500N Integration User Guide
Limitations
„
If offline Event messages are displayed, the Events received from the
panel not required to be in an order. This occurs due to panel prioritizing,
certain events are prioritize according to UL fire and burglary rules.
„
If any area is configured in the panel with a setting to Force Arm, Bypass
and, Refuse Arm the Bad zones, these changes will not be in effect if a
manual action is taken to arm any area in C•CURE. But, if a manual
action is taken to Force Arm an area, then all the bad zones will be Forced
Arm, and if a manual action is taken to Arm any area, all the bad zones
will be bypassed.
„
Monitor State of Pulsed DMP output is displayed as 'Active'. The actual
status, that is 'Pulsed' is displayed in Active Status.
„
If a manual action is taken on any DMP object, then the 'Manual Action
Activated' is shown at the same time, but the actual status change
message is shown on receiving the event from the panel, which might
take few seconds.
„
Performing a reset on any DMP zone is a onetime activity. So, if a manual
action is taken to reset any zone, then manual action activated message
will be displayed in the monitoring station, but manual action deactivated
message will not be displayed.
„
If any manual action is taken on DMP Zones and Areas, then on the end of
that manual action, the DMP object's status will changes to the state
opposite to the initial state.
„
For example
– If a manual action is taken to arm an area, then on the end of manual
action, the area status will change to disarm.
– If a manual action is taken to disarm an area, then on the end of
manual action, the area status will change to arm.
– If a manual action is taken to Bypass a zone, then on the end of
manual action, the zone status will change to reset.
„
In case of outputs, if a manual action is taken on any DMP output, then on
the end of manual action, the outputs status will revert back to its initial
state, that is if a manual action is taken to activate an inactive output, then
on the end of manual action, the output status will revert back to inactive.
DMP XR500N Integration User Guide
13-3
Limitations
13-4
„
If a manual action is taken to activate a pulsed output, then its status is
changed to Inactive first and then changed to active. If a manual action is
taken to pulse an activated output, then on the end of manual action, the
state is changed to inactive first and then changed to active.
„
If a Momentary Manual action is taken on DMP output, the manual action
activated and deactivated messages are displayed in Monitoring Station,
but state change messages are not displayed as no event is received from
panel for output state changed to Momentary
„
There is no state like 'Force Arm Area' in the panel, if a manual action is
taken to Force Arm an area, then for an instance it shows Force Arm, and
as soon as the event is received from the panel, which says that the area is
armed, the Area armed status changes to Armed. But, in case of DMP
controller, if a manual action is taken to Force Arm the system, the Armed
status of Controller is displayed as 'Forced Arm' till the manual action
ends.
„
Zone Alarm reporting in Monitoring Station takes about 25-30 second to
display, if the corresponding area is armed. If the area is not armed, the
alarms are reported quickly.This is the behavior of the panel and cannot
be controlled from C•CURE.
„
Performing 'Momentary Output' manual action activates DMP output for
One second, but the output active status in C•CURE is displayed as
'Momentary Slow Flash' for the duration provided in manual action.
„
Status of the DMP Output object which is not configured in panel can be
changed in C•CURE, but these changes are not effected in the panel as
they are not configured.
„
When DMP Intrusion Area is disarmed the DMP inputs that were in
bypassed state displays C•CURE supervision status as 'Bypass' instead of
'Open' due to the panel limitation.
„
Under section LX Bus/Wireless Inputs and LX Bus Outputs on DMP
Controller window, the LX Bus objects use both Input and Output grids in
the Secondary Device and Wireless Bus objects use only Input grids in the
Secondary Device. Under section Key Fob Inputs/Wireless Outputs on
DMP Controller window, the Key Fob Inputsobjects use Input grid and
Wireless Outputs use Output grid. Refer “DMP Controller-LX and
Wireless Devices Tab”.
DMP XR500N Integration User Guide
14
Troubleshooting
This chapter helps to resolve the problems occurred in C•CURE 9000 DMP
XR500N Integration software product.
This chapter covers
‹
Troubleshooting ............................................................................................................. 14-2
DMP XR500N Integration User Guide
14-1
Troubleshooting
Troubleshooting
Problem:
Controller will be offline even it is enabled.
Solution:
Install the reset jumper across the two J16 reset pins for two seconds. Remove
the reset jumper and place it over just one pin for future use.
Make sure that there are no other active connections with panel either from
remote link or C•CURE 9000 and check all the panel settings in Remote
Options section are proper. Refer “To configure Receiver Port” on page 6
Problem:
Access to Common Objects privilege.
Solution:
Perform the following steps:
1. Open the editor for Access to Common Objects for the partition
containing the hardware objects.
2. Use Create Copy button to create a new Privilege. This one will have the
Permission Specifies for all the classes shown in the editor.
3. Set the Privileges as desired for the 3rd party classes, including Exception
objects.
4. Assign the newly created Privilege to the Operator.
5. Remove the intrinsic Access to Common Objects for the partition from the
Operator.
14-2
DMP XR500N Integration User Guide
Troubleshooting
Problem:
Controller goes online, but does not respond to any of the manual action.
Solution:
Set the date time in the panel. Refer To configure Date and Time in DMP
Panel:
Problem:
Synchronize is not happening from controller screen after you enter IP
address, account number, and remote key.
Solution:
Save the controller and wait till the Online Status shows online value and then
initiate Synchronization.
Problem:
After synchronization, DMP objects are not appended in hardware tree.
Solution:
Check, if objects are configured in DMP Panel.
Problem:
To enable DMP Protocol messages (both to and from the Panel) in the Traces.
Solution:
Perform the following steps:
DMP XR500N Integration User Guide
14-3
Troubleshooting
1. Navigate to the path C:\Program Files\Software
House\SWHSystem\ServerComponents\DMPConfiguration.xml.
2. Open DMPConfiguration.xml.
3. Change the value of ProtocolPacketLog from False to True.
4. Restart the driver, now you can view the protocol message in trace
viewer.
Problem:
Warning : Low standby battery messages seen in the Monitoring Station.
Solution:
Between terminals 3 and 4, a battery of following specifications should be
connected: 12 VDC, 1.0 Amps Max. charging current. This is the standby
battery, its purpose is to provide power supply to the panel, when a main AC
power supply is cut off. If it is not connected, a warning appears: "Low battery
trouble" is provided.
Once these connections are made, it is required to initialize all the events of
the panel and do a manual reset. By doing this, the above mentioned warning
will not be reported by the panel.
Problem:
The Receiver Port configured in the controller is already being used by some
other application. Please use some other port or close that application." Is seen
in the Monitoring Station.
Solution:
Close the application, that is using the receiver port configured.
OR
Configure a different receiver port in Panel and C•Cure.
14-4
DMP XR500N Integration User Guide
Troubleshooting
Problem:
Not able to edit the DMPConfiguration.xml file.
Solution:
The file's "READONLY" attribute will be true. Make it false by right-clicking
on the file > Properties> uncheck the read-only field> Apply.
Problem:
Warning : Bell Circuit trouble messages seen in the Monitoring Station.
Solution:
Terminal 5 supplies positive 12 VDC to power alarm bells or horns. Terminal
6 is the ground reference for the bell circuit. This supervised output detects 1k
Ohms or less as normal. The indicating appliance can supply this resistance. If
the required resistance across terminals 5 and 6 is not present, Prompts a
warning: "Bell Circuit trouble".
Hence, to avoid this warning, a 1k Ohm 1/2 W EOL resistor (provided)
should be added across the bell circuit.
Once these connections are made, it is required to initialize all the events of
the panel and do a manual reset. By doing this, the above mentioned warning
will not be reported by the panel.
Problem
No Output events are received and visible in C•Cure.
Solution
While defining a new output in panel, select real time status field.
DMP XR500N Integration User Guide
14-5
Troubleshooting
Problem
AC Power Fail message is not displayed in Monitoring station even if there is
a Power failure at Panel's end.
Solution:
In Panel change the Power Fail Hours to Zero. To do that from keypad,
Programmer Mode > press 6653 > command > Till System Options Tab.
Then navigate through all the options till you reach 'Pwr Fail Hrs' and set its
value to Zero.
Problem:
When is the Controller status changed to Online/Offline.
Solution:
The controller Online/Offline status is governed by the ping
message("s0700003") sent by the panel every 2 minutes.
When the ping message is received, the controller status is set to Online. If no
ping message is received for a maximum duration of five minutes from Last
ping message received, then controller status is set to Offline.
14-6
DMP XR500N Integration User Guide
Index
A
C•CURE Personnel tab 8-4
Access Code 10-2
Controller Info 3-7
Access control 3-10
Action 3-16, 5-8, 10-3
Activate Event 5-9
Administration Client 1-5
Administration WorkStation 1-2
Alarm silence 1-3
Communication Info 3-7
Controllers 11-2
Create Personnel 11-2
CrossFire Server Component 2-10
Crossfire Services 2-2
Allow Any Time 8-10
D
Anti-Passback 8-9
Database 2-4
App Version 3-21
Architecture 1-5
Arm Authority 8-9
Arm Intrusion Area 10-4
Armed Status 3-15, 3-20, 4-8
Database Server 2-7
Details 3-15, 5-8
Disarm Intrusion Area 10-4
DMP Controller 3-2, 3-17
DMP Controllers 1-2
DMP driver 1-3
B
DMP Input 5-10
Board Location 7-6
DMP objects 1-5
Burglary zones 3-8
DMP Outputs 6-11
Bypass Input 10-4
DMP Secondary Device 7-3
Bypass Zone 8-8
DMP Security System 2
DMP XR500N Integration 1-2, 1-5
DMP User Profile 8-2
C
Door Access 8-7
Dynamic View 3-3, 4-10, 5-12
C•CURE 9000 Installation 2-2
C•CURE Personnel 8-11
DMP XR500N Integration User Guide
Index–1
Index
E
K
Easy Arm 8-9
Keypad bus 7-2
Ethernet port 1-5
Keypad bus devices 3-11
F
L
Fault alarm 10-8
Late Status 4-12
Force Arm 1-4
License program 2-3
LX bus 7-2
LX bus devices 3-13
G
General tab 6-5
Graphic annunciator 3-12
M
MAC Address 3-20
Main Board Inputs 3-9
H
Main Board Outputs 3-9
Hardware 3-2
Microsoft Operating System 2-3
Hardware security 4-9
Momentary 1-4
Hardware Status 5-14
Monitoring Station 1-2, 4-13, 11-2
Hardware Tree 2-2
O
I
Online Status 3-15, 3-19, 4-8
Identification 4-3, 5-5
Options 5-6
Individual users 9-2
Oracle database 2-4, 11-3
Input editor 5-2
Output icon 6-2
Input HW Status 5-9
Input Type 3-9
Inputs tab 7-7
P
Installation and Upgrade 2-2
Permissions 8-6
Integration software 2-2
Powered zone 3-8
Intrusion Areas 4-2
Profile Number 8-6
Index–2
DMP XR500N Integration User Guide
Index
Property 3-15, 5-8, 5-9
Property column 3-16
R
Re-arm Delay 8-6
T
Target Object 10-3
Time zone 11-2
Triggers 3-4
Triggers tab 4-7
Registration 2-3
Requirements 2-6
Reset Input 10-4
Reset Sensor 1-4
S
Schedule 5-8
U
Unique name 3-6
Use Second Language 8-9
User Codes 8-8
User Identification 9-4
User Profile Name 9-5
Security system 2-12
Serial Number 3-20
Service Required 8-8
Shifts tab 4-6
Silence Alarm 1-4
V
Value 3-15, 5-8
Version date 3-20
Single-zone 3-10
SQL Server 2-5
SQL Server 2005 2-4, 11-3
W
SQL Server Browser 2-5
Wireless device 3-12
State Images 3-5, 3-21
Wireless devices 3-13
Status tab 3-19, 4-11, 5-13
Wireless receiver 7-2
Supervision Status 5-9
Supervision status 5-14
Synchronization 3-7, 10-10
Z
Synchronization Status 3-15, 4-8
Zone event 1-2
Synchronize 1-4, 5-2, 10-4
Zone information 3-2
System drive 2-5
Zone Monito 8-8
Zones 4-2, 10-5
DMP XR500N Integration User Guide
Index–3
Index
Index–4
DMP XR500N Integration User Guide
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement