ABB RELION REB670 Product manual

Relion

®

670 series

Busbar protection REB670

Pre-configured

Product Guide


Pre-configured

Product version: 1.2

Contents

1. Application.....................................................................3

2. Available functions..........................................................9

3. Differential protection....................................................12

4. Zone selection..............................................................13

5. Current protection........................................................16

6. Control.........................................................................16

7. Logic............................................................................17

8. Monitoring....................................................................17

1MRK505212-BEN E

9. Basic IED functions......................................................19

10. Human machine interface............................................19

11. Station communication ...............................................20

12. Remote communication..............................................21

13. Hardware description..................................................21

14. Connection diagrams..................................................24

15. Technical data.............................................................30

16. Ordering......................................................................54

Disclaimer

The information in this document is subject to change without notice and should not be construed as a commitment by ABB. ABB assumes no responsibility for any errors that may appear in this document.

© Copyright 2012 ABB.

All rights reserved.

Trademarks

ABB and Relion are registered trademarks of the ABB Group. All other brand or product names mentioned in this document may be trademarks or registered trademarks of their respective holders.

2 ABB


Pre-configured


1MRK505212-BEN E

Issued: February 2015

Revision: E

1. Application

REB670 is designed for the selective, reliable and fast differential protection of busbars, T-connections and meshed corners. REB670 can be used for protection of single and double busbar with or without transfer bus, double circuit breaker or one-and-half circuit breaker stations. The IED is applicable for the protection of medium voltage (MV), high voltage (HV) and extra high voltage (EHV) installations at a power system frequency of 50Hz or 60Hz. The IED can detect all types of internal phase-to-phase and phase-toearth faults in solidly earthed or low impedance earthed power systems, as well as all internal multi-phase faults in isolated or high-impedance earthed power systems.

REB670 has very low requirements on the main current transformers (that is, CTs) and no interposing current transformers are necessary. For all applications, it is possible to include and mix main CTs with 1A and 5A rated secondary current within the same protection zone. Typically, CTs with up to 10:1 ratio difference can be used within the same differential protection zone. Adjustment for different main CT ratios is achieved numerically by a parameter setting.

The numerical, low-impedance differential protection function is designed for fast and selective protection for faults within protected zone. All connected CT inputs are provided with a restraint feature. The minimum pick-up value for the differential current is set to give a suitable sensitivity for all internal faults. For busbar protection applications typical

Sensitive differential protection

setting value for the minimum differential operating current is from 50% to 150% of the biggest CT. This setting is made directly in primary amperes. The operating slope for the differential operating characteristic is fixed to 53% in the algorithm.

The fast tripping time of the low-impedance differential protection function is especially advantageous for power system networks with high fault levels or where fast fault clearance is required for power system stability.

The advanced open CT detection algorithm detects instantly the open CT secondary circuits and prevents differential protection operation without any need for additional check zone.

Differential protection zones in REB670 include a sensitive operational level. This sensitive operational level is designed to be able to detect internal busbar earth faults in low impedance earthed power systems (that is, power systems where the earth-fault current is limited to a certain level, typically between 300A and 2000A primary by a neutral point reactor or resistor). Alternatively this sensitive level can be used when high sensitivity is required from busbar differential protection (that is, energizing of the bus via long line).

Overall operating characteristic of the differential function in

REB670 is shown in figure 1

.

Diff Oper Level

Sensitive Oper Level s=0.53

I d

=I in

Operate region

Sens Iin Block

Differential protection operation characteristic

I

in

[Primary Amps]

en06000142.vsd

IEC06000142 V1 EN

Figure 1.

REB670 operating characteristic

Integrated overall check zone feature, independent from any disconnector position, is available. It can be used in double busbar stations to secure stability of the busbar differential

ABB protection in case of entirely wrong status indication of busbar disconnector in any of the feeder bays.

3


Pre-configured


1MRK505212-BEN E

Flexible, software based dynamic Zone Selection enables easy and fast adaptation to the most common substation arrangements such as single busbar with or without transfer bus, double busbar with or without transfer bus, one-and-ahalf breaker stations, double busbar-double breaker stations, ring busbars, and so on. The software based dynamic Zone

Selections ensures:

• Dynamic linking of measured CT currents to the appropriate differential protection zone as required by substation topology

• Efficient merging of the two differential zones when required by substation topology (that is load-transfer)

• Selective operation of busbar differential protection ensures tripping only of circuit breakers connected to the faulty zone

• Correct marshaling of backup-trip commands from internally integrated or external circuit breaker failure protections to all surrounding circuit breakers

• Easy incorporation of bus-section and/or bus-coupler bays (that is, tie-breakers) with one or two sets of CTs into the protection scheme

• Disconnector and/or circuit breaker status supervision

Advanced Zone Selection logic accompanied by optionally available end-fault and/or circuit breaker failure protections ensure minimum possible tripping time and selectivity for faults within the blind spot or the end zone between bay CT and bay circuit breaker. Therefore REB670 offers best possible coverage for such faults in feeder and bus-section/ bus-coupler bays.

Optionally available circuit breaker failure protection, one for every CT input into REB670, offers secure local back-up protection for the circuit breakers in the station.

Optionally available four-stage, non-directional overcurrent protections, one for every CT input into REB670, provide remote backup functionality for connected feeders and remote-end stations.

It is normal practice to have just one busbar protection IED per busbar. Nevertheless some utilities do apply two independent busbar protection IEDs per zone of protection.

REB670 IED fits both solutions.

A simplified bus differential protection for multi-phase faults and earth faults can be obtained by using a single, one-phase

REB670 IED with external auxiliary summation current transformers.

The wide application flexibility makes this product an excellent choice for both new installations and the refurbishment of existing installations.

Description of 3 ph package A20

Three-phase version of the IED with two low-impedance differential protection zones and four three-phase CT inputs

A20. The version is intended for simpler applications such as

T-connections, meshed corners, and so on.

Description of 3 ph package A31

Three-phase version of the IED with two low-impedance differential protection zones and eight three-phase CT inputs

A31. The version is intended for applications on smaller busbars, with up to two zones and eight CT inputs.

Description of 1 ph packages B20 and B21

One-phase version of the IED with two low-impedance differential protection zones and twelve CT inputs B20, B21.

• Due to three available binary input modules, the B20 is intended for applications without need for dynamic Zone

Selection such as substations with single busbar with or without bus-section breaker, one-and-half breaker or double breaker arrangements. Three such IEDs offer cost effective solutions for such simple substation arrangements with up to twelve CT inputs.

• The B21 is intended for applications in substations where dynamic Zone Selection or bigger number of binary inputs and outputs is needed. Such stations for example are double busbar station with or without transfer bus with up to 12 CT inputs. Note that binary inputs can be shared between phases by including the

LDCM communication module. This simplifies panel wiring and saves IO boards.

• This version can be used with external auxiliary 3-phase to 1-phase summation current transformers with different turns ratio for each phase.

Description of 1 ph package B31

One-phase version of the IED with two low-impedance differential protection zones and twenty-four CT inputs B31.

• The IED is intended for busbar protection applications in big substations where dynamic Zone Selection, quite large number of binary inputs and outputs and many CT inputs are needed. The IED includes two differential zones and twenty-four CT inputs. Note that binary inputs can be shared between phases by including the LDCM communication module. This simplifies panel wiring and saves IO boards.

• This version can be used with external auxiliary 3-phase to 1-phase summation current transformers with different turns ratio for each phase.

Available configurations for pre-configured REB670

Three configurations have been made available for preconfigured REB670 IED. It shall be noted that all three configurations include the following features:

4 ABB


Pre-configured


1MRK505212-BEN E

• fully configured for the total available number of bays in each REB670 variant

• facility to take any bay out of service via the local HMI or externally via binary input

• facility to block any of the two zones via the local HMI or externally via binary input

• facility to block all bay trips via the local HMI or externally via binary input, but leaving all other function in service

(that is BBP Zones, BFP and OCP where applicable)

• facility to externally initiate built-in disturbance recorder

• facility to connect external breaker failure backup trip signal from every bay

• facility to connect external bay trip signal from every disconnector and/or circuit breaker. Thus full disconnector/breaker supervision is available. This configuration is available for only three REB670 variants

(that is A31, B21 and B31). It shall be noted that optional functions breaker failure protection CCRBRF, end fault protection and overcurrent protection PH4SPTOC can be ordered together with this configuration, but they will not be pre-configured. Thus these optional functions shall be configured by the end user.

Configuration X03

• This configuration includes BBP with breaker failure protection CCRBRF, end fault protection and overcurrent protection PH4SPTOC for double busbar-single breaker stations, where Zone Selection is done by using a and b auxiliary contacts from every disconnectors and/or circuit breakers. Thus full disconnector/breaker supervision is available. This configuration is available for only three REB670 variants (that is A31, B21 and B31).

Configuration X01

• This configuration includes just busbar protection for simple stations layouts (that is One-and-a-half breaker,

Double Breaker or Single Breaker stations). Additionally it can be used for double busbar-single breaker stations where disconnector replica is done by using just b auxiliary contact from every disconnector and/or circuit breakers. As a consequence no disconnector/breaker supervision will be available. It is as well possible to adapt this configuration by the Signal Matrix tool to be used as direct replacement of RED521 · 1.0 terminals.

This configuration is available for all five REB670 variants

(that is A20, A31, B20, B21 & B31). It shall be noted that optional functions breaker failure protection CCRBRF, end fault protection and overcurrent protection

PH4SPTOC can be ordered together with this configuration, but they will not be pre-configured. Thus these optional functions shall be configured by the end user.

Application examples of REB670

Examples of typical station layouts, which can be protected with REB670 are given below: xx06000009.vsd

IEC06000009 V1 EN

Figure 2.

Example of T-connection

Configuration X02

• This configuration includes just busbar protection for double busbar-single breaker stations, where Zone

Selection is done by using a and b auxiliary contacts

QB1

ZA ZB

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

IEC06000012 V1 EN

Figure 3.

Example of single bus station

QA1

BI1

QA1

BI1

QA1

BI1

xx06000012.vsd

ABB 5


Pre-configured


1MRK505212-BEN E

ZA

ZB

QB1 QB7

QA1

BI1

QB1 QB7 QB1 QB7

QA1

BI1

QA1

BI1

QB1 QB7

QA1

BI1

QB1

QA1

BI1

QB7 QB1 QB7

QA1

BI1

xx06000013.vsd

IEC06000013 V1 EN

Figure 4.

Example of single bus station with transfer bus

BI1

QA1

QB1 QB2 QB1 QB2 QB1 QB2 QB1 QB2 QB1 QB2 QB1 QB2

ZA

ZB

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

xx06000014.vsd

IEC06000014 V1 EN

Figure 5.

Example of double bus-single breaker station

ZA

ZB

QB1 QB2 QB7 QB1 QB2 QB7 QB1 QB2 QB7 QB20 QB1 QB2 QB7 QB1 QB2 QB7

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

xx06000015.vsd

IEC06000015 V1 EN

Figure 6.

Example of double bus-single breaker station with transfer bus

BI1

QA1

ZA1

ZB1

QB1 QB2 QB1 QB2

QA1

BI1

QA1

BI1

QB1 QB2 QB1 QB2 QB1 QB2

QA1

BI1

QA1

BI1

QA1

BI1

BI1

QA1

ZA2

BI1 QA1

QB1 QB2 QB1 QB2 QB1 QB2 QB1 QB2

ZB2

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

QA1

BI1

xx06000016.vsd

IEC06000016 V1 EN

Figure 7.

Example of double bus-single breaker station with two bus-section and two bus-coupler breakers

6 ABB


Pre-configured


ZA

QA1

BI1

QA2

BI2

BI3

QA3

QA1

BI1

QA2

BI2

BI3

QA3

QA1

BI1

QA2

BI2

BI3

QA3

QA1

BI1

QA2

BI2

BI3

QA3

QA1

BI1

QA2

BI2

BI3

QA3

IEC06000017 V1 EN

Figure 8.

Example of one-and-a-half breaker station

ZB

xx06000017.vsd

QA1

BI1

QA2

BI2

QA1

BI1

QA2

BI2

QA1

BI1

QA2

BI2

QA1

BI1

QA2

BI2

QA1

BI1

QA2

BI2

ZA

ZB

xx06000018.vsd

IEC06000018 V1 EN

Figure 9.

Example of double bus-double breaker station

BI8

ZA1

QB

8

QB11

BI1

QA1

QB41

QB12

BI5

QB

5

ZA2

QB21

QA4

BI4

BI7

QB42

ZB1

QB

7

QB31 BI3

QA3

QA2

BI2

QB22

QB32

QB

6

ZB2

BI6

xx06000019.vsd

IEC06000019 V1 EN

Figure 10.

Example of mesh or ring bus station

ABB

1MRK505212-BEN E

7


Pre-configured


1MRK505212-BEN E

Note that customized REB670 is delivered without any configuration. Thus the complete IED engineering shall be done by the customer or its system integrator. In order to secure proper operation of the busbar protection it is strictly recommended to always start engineering work from the PCM600 project for the pre-configured REB670 which is the closest to the actual application. Then, necessary modifications shall be applied in order to adopt the customized IED configuration to suite the actual station layout. The PCM600 project for the pre-configured REB670 IEDs is available in the Connectivity Package DVD.

8 ABB


Pre-configured


2. Available functions

Main protection functions

2 = number of basic instances

3-A03 = optional function included in packages A03 (refer to ordering details)

IEC 61850 ANSI Function description

1MRK505212-BEN E

Busbar

Differential protection

BUTPTRC,

BCZTPDIF,

BZNTPDIS,

BZITGGIO

87B

87B BUTPTRC,

BCZTPDIF,

BZNTPDIF,

BZITGGIO

BUSPTRC,

BCZSPDIF,

BZNSPDIF,

BZISGGIO

87B

BUSPTRC,

BCZSPDIF,

BZNSPDIF,

BZISGGIO

SWSGGIO

87B

Busbar differential protection, 2 zones, three phase/4 bays

Busbar differential protection, 2 zones, three phase/8 bays

Busbar differential protection, 2 zones, single phase/12 bays

Busbar differential protection, 2 zones, single phase/24 bays

1

Status of primary switching object for busbar protection zone selection 20

Back-up protection functions


1

1

Busbar

1

1

40 60 60 96

Current protection

OC4PTOC 51_67

PH4SPTOC 51

CCRBRF

CCSRBRF

50BF

50BF

Four step phase overcurrent protection

Four step single phase overcurrent protection

Breaker failure protection

Breaker failure protection, single phase version

4-C06 8-C07

4-C10 8-C11

12-

C08

12-

C12

12-

C08

12-

C12

24-

C08

24-

C13

ABB 9


Pre-configured


Control and monitoring functions


1MRK505212-BEN E

Busbar

FixedSignals

B16I

B16IFCVI

IB16

IB16FCVB

Monitoring

CVMMXN

EVENT

DRPRDRE

SPGGIO

SP16GGIO

MVGGIO

BSStatReport

RANGE_XP

Control

SMBRREC

QCBAY

LOCREM

LOCREMCTR

L

SLGGIO

VSGGIO

DPGGIO

SPC8GGIO

AutomationBits

SingleComma nd16Signals

Logic

79 Autorecloser

Apparatus control

Handling of LRswitch positions

LHMI control of PSTO

Logic rotating switch for function selection and LHMI presentation

Selector mini switch

IEC61850 generic communication I/O functions

Single pole generic control 8 signals

AutomationBits, command function for DNP3.0

Single command, 16 signals

15

20

16

5

3

4

2-H05 2-H05 2-H05 2-H05 2-H05

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

15

20

16

5

3

4

15

20

16

5

3

4

15

20

16

5

3

4

15

20

16

5

3

4

Configuration logic blocks

Fixed signal function block

Boolean 16 to Integer conversion

Boolean 16 to Integer conversion with Logic Node representation

Integer to Boolean 16 conversion

Integer to Boolean 16 conversion with Logic Node representation

Measurements

Event function

Disturbance report


IEC61850 generic communication I/O functions 16 inputs


Logical signal status report

Measured value expander block

16

24

3

28

6

20

1

64

40-280 40-28

0

1

16

1

16

16

16

16

16

16

16

40-280 40-280 40-28

0

1

16

1

16

1

16

16

16

16

16

16

16

16

16

16

6

20

1

64

16

24

3

28

6

20

1

64

16

24

3

28

6

20

1

64

16

24

3

28

16

24

3

28

6

20

1

64

10 ABB


Pre-configured


Designed to communicate


1MRK505212-BEN E

Busbar

Station communication

Remote communication

SPA communication protocol

LON communication protocol

IEC60870-5-103 communication protocol

Operation selection between SPA and IEC60870-5-103 for SLM

DNP3.0 for TCP/IP and EIA-485 communication protocol

DNP3.0 fault records for TCP/IP and EIA-485 communication protocol

Parameter setting function for IEC61850

Goose binary receive

Multiple command and transmit

Ethernet configuration of links

IEC 62439-3 Edition 1 parallel redundancy protocol

IEC 62439-3 Edition 2 parallel redundancy protocol

Binary signal transfer receive/transmit

Transmission of analog data from LDCM

Receive binary status from remote LDCM

1

1

1

1

20/1

1

1

1

20/1

1

1

1

20/1

1

1

1

20/1 20/1

1

1 1 1 1

1

1

1 1 1 1 1

1 1 1 1 1

10 10 10 10 10

60/10 60/10 60/10 60/10 60/10

1 1 1 1 1

1-P01 1-P01 1-P01 1-P01 1-P01

1-P02 1-P02 1-P02 1-P02 1-P02

6/36

1

6/36

1

6/36

1

6/36

1

6/36

1

6/3/3 6/3/3 6/3/3 6/3/3 6/3/3

ABB 11


Pre-configured


Basic IED functions

IEC 61850

Basic functions included in all products

IntErrorSig

TIME

TimeSynch

ActiveGroup

Test

ChangeLock

TerminalID

Productinfo

MiscBaseCommon

IEDRuntimeComp

RatedFreq

SMBI

SMBO

SMMI

SMAI

Sum3Ph

LocalHMI

LocalHMI

AuthStatus

AuthorityCheck

AccessFTP

SPACommMap

DOSFRNT

DOSOEMAB

DOSOEMCD

Function description

Self supervision with internal event list

Time and synchronization error

Time synchronization

Parameter setting groups

Test mode functionality

Change lock function

IED identifiers

Product information

Misc Base Common

IED Runtime Comp

Rated system frequency

Signal Matrix for binary inputs

Signal Matrix for binary outputs

Signal Matrix for mA inputs

Signal Matrix for analog inputs

Summation block 3 phase

Parameter setting function for HMI in PCM600

Local HMI signals

Authority status

Authority check

FTP access with password

SPA communication mapping

Denial of service, frame rate control for front port

Denial of service, frame rate control for OEM port AB

Denial of service, frame rate control for OEM port CD

1MRK505212-BEN E

40

4

24

12

1

1

40

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

3. Differential protection

The function consists of differential protection algorithm, sensitive differential protection algorithm, check zone algorithm, open CT algorithm and two supervision algorithms.

Busbar differential protection

This protection function is intended for fast and selective tripping of faults within protected zone. For each current input, the CT ratio can be set from the front HMI or via the parameter-setting tool, PCM600. In this way adaptation to different CT ratios is provided in the simplest way. The minimum pick-up value for the differential current is then set to give a suitable sensitivity for all internal faults. This setting is made directly in primary amperes. For busbar protection applications typical setting value for the minimum differential operating current is from 50% to 150% of the biggest CT.

The settings can be changed from the front HMI or via the parameter-setting tool, PCM600.

All current inputs are indirectly provided with a restraint feature. The operation is based on the well-proven RADSS percentage restraint stabilization principle, with an extra stabilization feature to stabilize for very heavy CT saturation.

Stability for external faults is guaranteed if a CT is not

12 ABB


Pre-configured


1MRK505212-BEN E saturated for at least two milliseconds during each power system cycle. It is also possible to add external tripping criteria by binary signal.

The trip command from the differential protection including sensitive differential protection and circuit breaker failure backup-trip commands can be set either as self-resetting or latched. In second case the manual reset is needed in order to reset the individual bay trip output contacts.

Sensitive differential level BZISGGIO

Differential protection zones in REB670 include a sensitive operational level. This sensitive operational level is designed to be able to detect internal busbar earth faults in low impedance earthed power systems (i.e. power systems where the earth-fault current is limited to a certain level, typically between 300A and 2000A primary by a neutral point reactor or resistor). For increased security, the sensitive differential protection must be externally enabled by a binary signal (e.g.

from external open delta VT overvoltage relay or external power transformer neutral point overcurrent relay). Finally it is as well possible to set a time delay before the trip signal from the sensitive differential protection is given. This sensitive level can be alternatively used in special applications when high sensitivity is required from busbar differential protection

(i.e. energizing of dead bus via a long line).

Operation and operating characteristic of the sensitive differential protection can be set independently from the operating characteristic of the main differential protection.

However, the sensitive differential level is blocked as soon as the total incoming current exceeds the pre-set level or when differential current exceed the set minimum pickup current for the usual differential protection. Therefore, by appropriate settings it can be ensured that this sensitive level is blocked for all external multi-phase faults, which can cause CT saturation. Operating characteristic of sensitive differential characteristics is shown in figure

1

.

Check zone

For busbar protection in double busbar stations when dynamic zone selection is needed, it is sometimes required to include the overall differential zone (that is, check zone).

Hence, the built-in, overall check zone is available in the IED.

Because the built-in check zone current measurement is not dependent on the disconnector status, this feature ensures stability of Busbar differential protection even for completely wrong status indication from the busbar disconnectors. It is to be noted that the overall check zone, only supervise the usual differential protection operation. The external trip commands, breaker failure backup-trip commands and sensitive differential protection operation are not supervised by the overall check zone.

The overall check zone has simple current operating algorithm, which ensures check zone operation for all internal faults regardless the fault current distribution. To achieve this, the outgoing current from the overall check zone is used as

ABB restraint quantity. If required, the check zone operation can be activated externally by a binary signal.

Open CT detection

The innovative measuring algorithm provides stability for open or short-circuited main CT secondary circuits, which means that no separate check zone is actually necessary. Start current level for open CT detection can usually be set to detect the open circuit condition for the smallest CT. This built-in feature allows the protection terminal to be set very sensitive, even to a lower value than the maximum CT primary rating in the station. At detection of problems in CT secondary circuits, the differential protection can be instantly blocked and an alarm is given. Alternatively, the differential protection can be automatically desensitized in order to ensure busbar differential protection stability during normal through-load condition. When problems in CT secondary circuits have been found and associated error has been corrected a manual reset must be given to the IED. This can be done locally from the local HMI, or remotely via binary input or communication link.

However, it is to be noted that this feature can only be partly utilized when the summation principle is in use.

Differential protection supervision

Dual monitoring of differential protection status is available.

The first monitoring feature operates after settable time delay when differential current is higher than the user settable level.

This feature can be, for example, used to design automatic reset logic for previously described open CT detection feature. The second monitoring feature operates immediately when the busbar through-going current is bigger than the user settable level. Both of these monitoring features are phase segregated and they give out binary signals, which can be either used to trigger disturbance recorder or for alarming purposes.

4. Zone selection

Typically CT secondary circuits from every bay in the station are connected to the busbar protection. The built-in software feature called “Zone Selection” gives a simple but efficient control over the connected CTs to busbar protection IED in order to provide fully operational differential protection scheme for multi-zone applications on both small and large buses.

The function consists of dedicated disconnector/circuit breaker status monitoring algorithm, bay dedicated CTconnection control algorithm and zone interconnection algorithm.

Switch status monitoring

For stations with complex primary layout (that is, double busbar single breaker station with or without transfer bus) the information about busbar disconnector position in every bay is crucial information for busbar protection. The positions of

13


Pre-configured


1MRK505212-BEN E these disconnectors then actually determine which CT input

(that is, bay) is connected to which differential protection zone. For some more advanced features like end-fault or blind-spot protection the actual status of the circuit breaker in some or even all bays can be vital information for busbar protection as well. The switch function block is used to take the status of two auxiliary contacts from the primary device, evaluate them and then to deliver the device primary contact position to the rest of the zone selection logic.

For such applications typically two auxiliary contacts (that is, normally open and normally closed auxiliary contacts) from each relevant primary switching object shall be connected to the IED. Then the status for every individual primary switching object will be determined. The dedicated function block for each primary switching object is available in order to determine the status of the object primary contacts. By a parameter setting one of the following two logical schemes can be selected for each primary object individually by the end user:

• If not open then closed (that is, as in RADSS schemes)

• Open or closed only when clearly indicated by aux contact status (that is, as in INX schemes)

Table 1

gives quick overview about both schemes.

Note that the first scheme only requires fast breaking normally closed auxiliary contact (that is, b contact) for proper operation. The timing of normally open auxiliary contact is not critical because it is only used for supervision of the primary object status. The second scheme in addition requires properly timed-adjusted, early-making normally open auxiliary contact (that is, early making a contact) for proper operation.

Regardless which scheme is used the time-delayed disconnector/circuit breaker status supervision alarm is available (that is, 00 or 11 auxiliary contact status). How two integrated differential protection zones behave when disconnector alarm appears is freely configurable by the end user.

It is possible by a parameter setting to override the primary object status as either permanently open or permanently closed. This feature can be useful during testing, installation and commissioning of the busbar protection scheme. At the same time, separate alarm is given to indicate that the actual object status is overwritten by a setting parameter.

It is to be noted that it is as well possible to use only normally closed auxiliary contacts for Zone Selection logic. In that case the Switch function blocks are not used.

Table 1. Treatment of primary object auxiliary contact status

Primary equipment

Normally Open auxiliary contact status

(that is,

“closed” or

“a” contact) open

Normally

Closed auxiliary contact status

(that is,

“open” or “b” contact) open

Status in busbar protection when

“Scheme 1

RADSS” is selected when

“Scheme 2

INX” is selected closed closed open

Last position saved open open closed closed open closed closed closed closed closed

Alarm facility

Alarm after settable time delay yes no no yes

Information visible on local HMI intermediate_00 open closed badState_11

Bay

Each CT input is allocated to one dedicated bay function block. This function block is used to provide complete user interface for all signals from and towards this bay. It is also used to influence bay measured current.

It is possible by a parameter setting

CTConnection

to connect or disconnect the CT input to the bay function block. Once the CT input is connected to the bay function block this associated current input can be included to or excluded from the two internally available differential functions in software.

This can be done by a parameter setting for simple station layouts (that is, one-and-a-half breaker stations) or alternatively via dedicated logical scheme (that is, double busbar stations). For each bay the end user have to select one of the following five alternatives:

14 ABB


Pre-configured


1MRK505212-BEN E

• Permanently connect this bay current to zone A (that is,

ZA)

• Permanently connect this bay current to zone B (that is,

ZB)

• Permanently connect this bay current to zone A and inverted bay current to ZB (that is, ZA and ZB)

• Connect this bay current to ZA or ZB depending on the logical status of the two input binary signals available on this bay function block. These two input signals will include measured current to the respective zone when their logical value is one (that is,

CntrlIncludes

). This option is used together with above described Switch function blocks in order to provide complete Zone

Selection logic

• Connect the bay current to ZA or ZB depending on the logical status of the two input binary signals available on this bay function block. These two signals will include measured current to the respective zone when their logical value is zero (that is,

CntrlExcludes

). This option is typically used when only normally closed auxiliary contacts from the busbar disconnector are available to the Zone Selection logic

At the same time, an additional feature for instantaneous or time delayed disconnection or even inversion of the connected bay current via separate logical signals is also available. This feature is provided in order to facilitate for bussection or bus-coupler CT disconnection for tie-breakers with a CT only on one side of the circuit breaker. This ensures correct and fast fault clearance of faults between the CT and the circuit breaker within these bays. The same feature can be individually used in any feeder bay to optimize Busbar differential protection performance, when feeder circuit breaker is open. Thus, the end-fault protection for faults between circuit breaker and the CT is available. However, to use this feature circuit breaker auxiliary contacts and closing command to the circuit breaker shall be wired to the binary inputs of the IED. Therefore, he IED offers best possible coverage for these special faults between CT and circuit breaker in feeder and bus-section/bus-coupler bays.

Within the Bay function block it is decided by a parameter setting how this bay should behave during zone interconnection (that is, load transfer). For each bay individually one of the following three options can be selected:

• Bay current is forced out from both zones during zone interconnection (used for bus-coupler bays)

• Bay current is unconditionally forced into both zones during zone interconnection (used in special applications)

• Bay current is connected to both zones during zone interconnection if the bay was previously connected to one of the two zones (typically used for feeder bays)

The third option ensures that the feeder, which is out of service, is not connected to any of the two zones during zone interconnection.

Within the Bay function block it is decided by a parameter setting whether this bay should be connected to the check zone or not. In this way the end user has simple control over the bays, which shall be connected to the overall check zone.

By appropriate configuration logic it is possible to take any bay (that is, CT input) out of service. This can be done from the local HMI or externally via binary signal. In that case all internal current measuring functions (that is, differential protection, sensitive differential protection, check zone, breaker failure protection and overcurrent protection) are disabled. At the same time, any trip command to this bay circuit breaker can be inhibited.

Via two dedicated binary input signals it is possible to:

• Trip only the bay circuit breaker (used for integrated OC protection tripping)

• Trip the whole differential zone to which this bay is presently connected (used for backup-trip command from either integrated or external bay circuit breaker failure protection)

Finally dedicated trip binary output from the Bay function block is available in order to provide common trip signal to the bay circuit breaker from busbar differential protection, breaker failure protection, backup overcurrent protection and so on.

In this way the interface to the user is kept as simple as possible and IED engineering work is quite straight forward.

Zone interconnection (Load transfer)

When this feature is activated the two integrated differential protection zones are merged into one common, overall differential zone. This feature is required in double busbar stations when in any of the feeder bays both busbar disconnectors are closed at the same time (that is, load transfer). As explained in above section Bay each CT input will then behave in the pre-set way in order to ensure proper current balancing during this special condition. This feature can be started automatically (when Zone Selection logic determines that both busbar disconnectors in one feeder bay are closed at the same time) or externally via dedicated binary signal. If this feature is active for longer time than the pre-set vale the alarm signal is given.

ABB 15


Pre-configured


1MRK505212-BEN E

5. Current protection

Four step phase overcurrent protection OC4PTOC

The four step phase overcurrent protection function

OC4PTOC has an inverse or definite time delay independent for step 1 and 4 separately. Step 2 and 3 are always definite time delayed.

All IEC and ANSI inverse time characteristics are available together with an optional user defined time characteristic.

The directional function is voltage polarized with memory. The function can be set to be directional or non-directional independently for each of the steps.

Second harmonic blocking level can be set for the function and can be used to block each step individually

This function can be used as a backup bay protection (e.g.

for transformers, reactors, shunt capacitors and tie-breakers).

A special application is to use this phase overcurrent protection to detect short-circuits between the feeder circuit breaker and feeder CT in a feeder bay when the circuit breaker is open. This functionality is called end-fault protection. In such case unnecessarily operation of the busbar differential protection can be prevented and only fast overcurrent trip signal can be sent to the remote line end. In order to utilize this functionality the circuit breaker status and

CB closing command must be connected to the REB670.

One of the overcurrent steps can be set and configured to act as end-fault protection in REB670.

CCRBRF can be single- or three-phase initiated to allow use with single phase tripping applications. For the three-phase version of CCRBRF the current criteria can be set to operate only if two out of four for example, two phases or one phase plus the residual current start. This gives a higher security to the back-up trip command.

CCRBRF function can be programmed to give a single- or three-phase re-trip of the own breaker to avoid unnecessary tripping of surrounding breakers at an incorrect initiation due to mistakes during testing.

Breaker failure protection, single phase version CCSRBRF

Breaker failure protection, single phase version (CCSRBRF) function ensures fast back-up tripping of surrounding breakers.

A current check with extremely short reset time is used as check criteria to achieve a high security against unnecessary operation.

CCSRBRF can be programmed to give a re-trip of the own breaker to avoid unnecessary tripping of surrounding breakers at an incorrect starting due to mistakes during testing.

The function is normally used as end fault protection to clear faults between current transformer and circuit breaker.

Four step single phase overcurrent protection PH4SPTOC

Four step single phase overcurrent protection

(PH4SPTOC)has an inverse or definite time delay independent for each step separately.

All IEC and ANSI time delayed characteristics are available together with an optional user defined time characteristic.

The function is normally used as end fault protection to clear faults between current transformer and circuit breaker.

Breaker failure protection CCRBRF

Breaker failure protection (CCRBRF) ensures fast back-up tripping of surrounding breakers in case the own breaker fails to open. CCRBRF can be current based, contact based, or an adaptive combination of these two conditions.

Current check with extremely short reset time is used as check criterion to achieve high security against inadvertent operation.

Contact check criteria can be used where the fault current through the breaker is small.

6. Control

Autorecloser SMBRREC

The autoreclosing function provides high-speed and/or delayed three pole autoreclosing. The autoreclosing can be used for delayed busbar restoration. One Autorecloser

(SMBRREC) per zone can be made available.

Logic rotating switch for function selection and LHMI presentation SLGGIO

The logic rotating switch for function selection and LHMI presentation (SLGGIO) (or the selector switch function block) is used to get a selector switch functionality similar to the one provided by a hardware selector switch. Hardware selector switches are used extensively by utilities, in order to have different functions operating on pre-set values. Hardware switches are however sources for maintenance issues, lower system reliability and an extended purchase portfolio. The logic selector switches eliminate all these problems.

Selector mini switch VSGGIO

The Selector mini switch VSGGIO function block is a multipurpose function used for a variety of applications, as a general purpose switch.

VSGGIO can be controlled from the menu or from a symbol on the single line diagram (SLD) on the local HMI.

Single point generic control 8 signals SPC8GGIO

The Single point generic control 8 signals (SPC8GGIO) function block is a collection of 8 single point commands, designed to bring in commands from REMOTE (SCADA) to

16 ABB


Pre-configured


1MRK505212-BEN E those parts of the logic configuration that do not need extensive command receiving functionality (for example,

SCSWI). In this way, simple commands can be sent directly to the IED outputs, without confirmation. Confirmation (status) of the result of the commands is supposed to be achieved by other means, such as binary inputs and SPGGIO function blocks. The commands can be pulsed or steady.

AutomationBits, command function for DNP3.0 AUTOBITS

AutomationBits function for DNP3 (AUTOBITS) is used within

PCM600 to get into the configuration of the commands coming through the DNP3 protocol. The AUTOBITS function plays the same role as functions GOOSEBINRCV (for IEC

61850) and MULTICMDRCV (for LON).

Single command, 16 signals

The IEDs can receive commands either from a substation automation system or from the local HMI. The command function block has outputs that can be used, for example, to control high voltage apparatuses or for other user defined functionality.

controls if the block's output should reset or return to the state it was, after a power interruption. RESET input has priority.

Fixed signal function block

The Fixed signals function (FXDSIGN) generates a number of pre-set (fixed) signals that can be used in the configuration of an IED, either for forcing the unused inputs in other function blocks to a certain level/value, or for creating certain logic.

8. Monitoring

Measurements CVMMXN, CMMXU, VNMMXU, VMMXU,

CMSQI, VMSQI

The measurement functions are used to get on-line information from the IED. These service values make it possible to display on-line information on the local HMI and on the Substation automation system about:

• measured voltages, currents, frequency, active, reactive and apparent power and power factor

• primary and secondary phasors

• positive, negative and zero sequence currents and voltages

• mA, input currents

• pulse counters

7. Logic

Configurable logic blocks

A number of logic blocks and timers are available for the user to adapt the configuration to the specific application needs.

• OR function block.

• INVERTER function blocks that inverts the input signal.

• PULSETIMER function block can be used, for example, for pulse extensions or limiting of operation of outputs, settable pulse time.

• GATE function block is used for whether or not a signal should be able to pass from the input to the output.

• XOR function block.

• LOOPDELAY function block used to delay the output signal one execution cycle.

• TIMERSET function has pick-up and drop-out delayed outputs related to the input signal. The timer has a settable time delay.

• AND function block.

• SRMEMORY function block is a flip-flop that can set or reset an output from two inputs respectively. Each block has two outputs where one is inverted. The memory setting controls if the block's output should reset or return to the state it was, after a power interruption. Set input has priority.

• RSMEMORY function block is a flip-flop that can reset or set an output from two inputs respectively. Each block has two outputs where one is inverted. The memory setting

ABB

Event counter CNTGGIO

Event counter (CNTGGIO) has six counters which are used for storing the number of times each counter input has been activated.

Disturbance report DRPRDRE

Complete and reliable information about disturbances in the primary and/or in the secondary system together with continuous event-logging is accomplished by the disturbance report functionality.

Disturbance report DRPRDRE, always included in the IED, acquires sampled data of all selected analog input and binary signals connected to the function block with a, maximum of

40 analog and 96 binary signals.

The Disturbance report functionality is a common name for several functions:

• Event list

• Indications

• Event recorder

• Trip value recorder

• Disturbance recorder

The Disturbance report function is characterized by great flexibility regarding configuration, starting conditions, recording times, and large storage capacity.

17


Pre-configured


1MRK505212-BEN E

A disturbance is defined as an activation of an input to the

AxRADR or BxRBDR function blocks, which are set to trigger the disturbance recorder. All signals from start of pre-fault time to the end of post-fault time will be included in the recording.

Every disturbance report recording is saved in the IED in the standard Comtrade format. The same applies to all events, which are continuously saved in a ring-buffer. The local HMI is used to get information about the recordings. The disturbance report files may be uploaded to PCM600 for further analysis using the disturbance handling tool.

Event list DRPRDRE

Continuous event-logging is useful for monitoring the system from an overview perspective and is a complement to specific disturbance recorder functions.

The event list logs all binary input signals connected to the

Disturbance report function. The list may contain up to 1000 time-tagged events stored in a ring-buffer.

Indications DRPRDRE

To get fast, condensed and reliable information about disturbances in the primary and/or in the secondary system it is important to know, for example binary signals that have changed status during a disturbance. This information is used in the short perspective to get information via the local HMI in a straightforward way.

There are three LEDs on the local HMI (green, yellow and red), which will display status information about the IED and the Disturbance report function (triggered).

The Indication list function shows all selected binary input signals connected to the Disturbance report function that have changed status during a disturbance.

Event recorder DRPRDRE

Quick, complete and reliable information about disturbances in the primary and/or in the secondary system is vital, for example, time-tagged events logged during disturbances.

This information is used for different purposes in the short term (for example corrective actions) and in the long term (for example functional analysis).

The event recorder logs all selected binary input signals connected to the Disturbance report function. Each recording can contain up to 150 time-tagged events.

The event recorder information is available for the disturbances locally in the IED.

The event recording information is an integrated part of the disturbance record (Comtrade file).

Trip value recorder DRPRDRE

Information about the pre-fault and fault values for currents and voltages are vital for the disturbance evaluation.

The Trip value recorder calculates the values of all selected analog input signals connected to the Disturbance report function. The result is magnitude and phase angle before and during the fault for each analog input signal.

The trip value recorder information is available for the disturbances locally in the IED.

The trip value recorder information is an integrated part of the disturbance record (Comtrade file).

Disturbance recorder DRPRDRE

The Disturbance recorder function supplies fast, complete and reliable information about disturbances in the power system. It facilitates understanding system behavior and related primary and secondary equipment during and after a disturbance. Recorded information is used for different purposes in the short perspective (for example corrective actions) and long perspective (for example functional analysis).

The Disturbance recorder acquires sampled data from selected analog- and binary signals connected to the

Disturbance report function (maximum 40 analog and 96 binary signals). The binary signals available are the same as for the event recorder function.

The function is characterized by great flexibility and is not dependent on the operation of protection functions. It can record disturbances not detected by protection functions. Up to ten seconds of data before the trigger instant can be saved in the disturbance file.

The disturbance recorder information for up to 100 disturbances are saved in the IED and the local HMI is used to view the list of recordings.

Event function

When using a Substation Automation system with LON or

SPA communication, time-tagged events can be sent at change or cyclically from the IED to the station level. These events are created from any available signal in the IED that is connected to the Event function (EVENT). The event function block is used for LON and SPA communication.

Analog and double indication values are also transferred through EVENT function.

IEC61850 generic communication I/O functions MVGGIO

IEC61850 generic communication I/O functions (MVGGIO) function is used to send the instantaneous value of an analog signal to other systems or equipment in the substation. It can also be used inside the same IED, to attach a RANGE aspect to an analog value and to permit measurement supervision on that value.

18 ABB


Pre-configured


Measured value expander block RANGE_XP

The current and voltage measurements functions (CVMMXN,

CMMXU, VMMXU and VNMMXU), current and voltage sequence measurement functions (CMSQI and VMSQI) and

IEC 61850 generic communication I/O functions (MVGGIO) are provided with measurement supervision functionality. All measured values can be supervised with four settable limits: low-low limit, low limit, high limit and high-high limit. The measure value expander block (RANGE_XP) has been introduced to enable translating the integer output signal from the measuring functions to 5 binary signals: below low-low limit, below low limit, normal, above high-high limit or above high limit. The output signals can be used as conditions in the configurable logic or for alarming purpose.

9. Basic IED functions

Time synchronization

The time synchronization source selector is used to select a common source of absolute time for the IED when it is a part of a protection system. This makes it possible to compare event and disturbance data between all IEDs in a station automation system.

IEC06000143 V1 EN

Figure 11.

Example of medium graphic HMI

10. Human machine interface

Human machine interface

The local HMI is equipped with a LCD that is used among other things to locally display the following crucial information:

• Connection of each bay, respecting the two differential protection zones and the check zone. In the Parameter

Setting Tool the user sets individual bay names to facilitate the identification of each primary bay for station personnel.

• Status of each individual primary switchgear device, for example, open, closed, 00 as intermediate state and 11 as bad state. In PCM600 the user sets the individual primary switchgear object names to facilitate the identification of each switchgear device for the station personnel.

The local HMI is divided into zones with different functionality.

• Status indication LEDs.

• Alarm indication LEDs, which consist of 15 LEDs (6 red and 9 yellow) with user printable label. All LEDs are configurable from PCM600.

• Liquid crystal display (LCD).

• Keypad with push buttons for control and navigation purposes, switch for selection between local and remote control and reset.

• Isolated RJ45 communication port.

1MRK505212-BEN E

ABB 19


Pre-configured


1MRK505212-BEN E

IEC06000191 V1 EN

Figure 12.

Bay to zone connection example

1 User settable bay name

2 Internally used bay FB

3 Connections to internal zones

20

IEC06000192 V1 EN

Figure 13.

Example of status of primary switchgear objects

1 User settable switchgear names

2 Switchgear object status

11. Station communication

Overview

Each IED is provided with a communication interface, enabling it to connect to one or many substation level systems or equipment, either on the Substation Automation

(SA) bus or Substation Monitoring (SM) bus.

Following communication protocols are available:

• IEC 61850-8-1 communication protocol

• LON communication protocol

• SPA or IEC 60870-5-103 communication protocol

• DNP3.0 communication protocol

Theoretically, several protocols can be combined in the same

IED.

IEC 61850-8-1 communication protocol

The IED is equipped with single or double optical Ethernet rear ports (order dependent) for IEC 61850-8-1 station bus communication. The IEC 61850-8-1 communication is also possible from the optical Ethernet front port. IEC 61850-8-1 protocol allows intelligent electrical devices (IEDs) from different vendors to exchange information and simplifies system engineering. Peer-to-peer communication according

ABB


Pre-configured


1MRK505212-BEN E to GOOSE is part of the standard. Disturbance files uploading is provided.

Serial communication, LON

Existing stations with ABB station bus LON can be extended with use of the optical LON interface. This allows full SA functionality including peer-to-peer messaging and cooperation between existing ABB IED's and the new IED

670.

SPA communication protocol

A single glass or plastic port is provided for the ABB SPA protocol. This allows extensions of simple substation automation systems but the main use is for Substation

Monitoring Systems SMS.

IEC 60870-5-103 communication protocol

A single glass or plastic port is provided for the

IEC60870-5-103 standard. This allows design of simple substation automation systems including equipment from different vendors. Disturbance files uploading is provided.

DNP3.0 communication protocol

An electrical RS485 and an optical Ethernet port is available for the DNP3.0 communication. DNP3.0 Level 2 communication with unsolicited events, time synchronizing and disturbance reporting is provided for communication to

RTUs, Gateways or HMI systems.

Multiple command and transmit

When 670 IED's are used in Substation Automation systems with LON, SPA or IEC60870-5-103 communication protocols the Event and Multiple Command function blocks are used as the communication interface for vertical communication to station HMI and gateway and as interface for horizontal peerto-peer communication (over LON only).

IEC 62439-3 Parallel Redundant Protocol

Redundant station bus communication according to IEC

62439-3 Edition 1 and IEC 62439-3 Edition 2 are available as options in 670 series IEDs. IEC 62439-3 parallel redundant protocol is an optional quantity and the selection is made at ordering. Redundant station bus communication according to

IEC 62439-3 uses both port AB and port CD on the OEM module.

ABB

Select IEC 62439-3 Edition 1 protocol at the time of ordering when an existing redundant station bus DuoDriver installation is extended.

Select IEC 62439-3 Edition 2 protocol at the time of ordering for new installations with redundant station bus.

IEC 62439-3 Edition 1 is NOT compatible with IEC 62439-3 Edition 2.

12. Remote communication

Analog and binary signal transfer to remote end

Three analog and eight binary signals can be exchanged between two IEDs. This functionality is mainly used for the line differential protection. However it can be used in other products as well. An IED can communicate with up to 4 remote IEDs.

Binary signal transfer to remote end, 192 signals

If the communication channel is used for transfer of binary signals only, up to 192 binary signals can be exchanged between two IEDs. For example, this functionality can be used to send information such as status of primary switchgear apparatus or intertripping signals to the remote

IED. An IED can communicate with up to 4 remote IEDs.

Line data communication module, short range LDCM

The line data communication module (LDCM) is used for communication between the IEDs situated at distances <110 km or from the IED to optical to electrical converter with G.

703 or G.703E1 interface located on a distances <3 km away. The LDCM module sends and receives data, to and from another LDCM module. The IEEE/ANSI C37.94 standard format is used.

13. Hardware description

Hardware modules

Power supply module PSM

The power supply module is used to provide the correct internal voltages and full isolation between the terminal and the battery system. An internal fail alarm output is available.

Binary input module BIM

The binary input module has 16 optically isolated inputs and is available in two versions, one standard and one with enhanced pulse counting capabilities on the inputs to be used with the pulse counter function. The binary inputs are freely programmable and can be used for the input of logical signals to any of the functions. They can also be included in the disturbance recording and event-recording functions. This enables extensive monitoring and evaluation of operation of the IED and for all associated electrical circuits.

Binary output module BOM

The binary output module has 24 independent output relays and is used for trip output or any signaling purpose.

Static binary output module SOM

The static binary output module has six fast static outputs and six change over output relays for use in applications with high speed requirements.

Binary input/output module IOM

The binary input/output module is used when only a few input and output channels are needed. The ten standard output channels are used for trip output or any signaling purpose.

21


Pre-configured


1MRK505212-BEN E

The two high speed signal output channels are used for applications where short operating time is essential. Eight optically isolated binary inputs cater for required binary input information.

Optical ethernet module OEM

The optical fast-ethernet module is used to connect an IED to the communication buses (like the station bus) that use the

IEC 61850-8-1 protocol (port A, B). The module has one or two optical ports with ST connectors.

Serial and LON communication module SLM, supports SPA/

IEC 60870-5-103, LON and DNP 3.0

The serial and LON communication module (SLM) is used for

SPA, IEC 60870-5-103, DNP3 and LON communication. The module has two optical communication ports for plastic/ plastic, plastic/glass or glass/glass. One port is used for serial communication (SPA, IEC 60870-5-103 and DNP3 port or dedicated IEC 60870-5-103 port depending on ordered SLM module) and one port is dedicated for LON communication.

Line data communication module LDCM

Each module has one optical port, one for each remote end to which the IED communicates.

Alternative cards for Short range (850 nm multi mode) are available.

Galvanic RS485 serial communication module

The Galvanic RS485 communication module (RS485) is used for DNP3.0 communication. The module has one RS485 communication port. The RS485 is a balanced serial communication that can be used either in 2-wire or 4-wire connections. A 2-wire connection uses the same signal for RX and TX and is a multidrop communication with no dedicated

Master or slave. This variant requires however a control of the output. The 4-wire connection has separated signals for RX and TX multidrop communication with a dedicated Master and the rest are slaves. No special control signal is needed in this case.

GPS time synchronization module GTM

This module includes a GPS receiver used for time synchronization. The GPS has one SMA contact for connection to an antenna. It also includes an optical PPS STconnector output.

IRIG-B Time synchronizing module

The IRIG-B time synchronizing module is used for accurate time synchronizing of the IED from a station clock.

Transformer input module TRM

The transformer input module is used to galvanically separate and transform the secondary currents and voltages generated by the measuring transformers. The module has twelve inputs in different combinations of currents and voltage inputs.

Alternative connectors of Ring lug or Compression type can be ordered.

Layout and dimensions

Dimensions

F

E

A

B

C

D xx05000003.vsd

IEC05000003 V1 EN

Figure 14.

1/2 x 19” case with rear cover

22 ABB


Pre-configured


1MRK505212-BEN E xx05000004.vsd

IEC05000004 V1 EN

Figure 15.

Side-by-side mounting

Case size

6U, 1/2 x 19”

6U, 3/4 x 19”

6U, 1/1 x 19”

Mounting alternatives

• 19” rack mounting kit

• Flush mounting kit with cut-out dimensions:

– 1/2 case size (h) 254.3 mm (w) 210.1 mm

– 1/1 case size (h) 254.3 mm (w) 434.7 mm

• Wall mounting kit

A B C D E F

265.9

223.7

201.1

242.1

252.9

205.7

265.9

336.0

201.1

242.1

252.9

318.0

265.9

448.1

201.1

242.1

252.9

430.3

(mm)

See ordering for details about available mounting alternatives.

ABB 23


Pre-configured


14. Connection diagrams

Table 2. Designations for 1/2 x 19” casing with 1 TRM slot

Module

PSM

BIM, BOM, SOM, IOM or

MIM

SLM

LDCM, IRIG-B or RS485

LDCM or RS485

OEM

LDCM, RS485 or GTM

TRM

Rear Positions

X11

X31 and X32 etc. to X51 and X52

X301:A, B, C, D

X302

X303

X311:A, B, C, D

X312, 313

X401

1MRK505212-BEN E

1MRK002801-AC-2-670-1.2-PG V1 EN

Table 3. Designations for 3/4 x 19” casing with 1 TRM slot

Module

PSM

BIM, BOM, SOM, IOM or

MIM

Rear Positions

X11

X31 and X32 etc. to

X101 and X102

SLM X301:A, B, C, D

LDCM, IRIG-B or RS485 X302

LDCM or RS485

OEM

X303

X311:A, B, C, D

LDCM, RS485 or GTM

TRM

X312, X313

X401

1MRK002801-AC-3-670-1.2-PG V1 EN

24 ABB


Pre-configured


Table 4. Designations for 1/1 x 19” casing with 2 TRM slots

1MRK505212-BEN E

Module Rear Positions

PSM

BIM, BOM, SOM,

IOM or MIM

SLM

X11

X31 and X32 etc. to X131 and X132

LDCM, IRIG-B or

RS485

X301:A, B, C, D

X302

LDCM or RS485 X303

OEM X311:A, B, C, D

LDCM, RS485 or

GTM

X312, X313, X322, X323

TRM 1

TRM 2

X401

X411

1MRK002801-AC-6-670-1.2-PG V1 EN

ABB 25


Pre-configured


1MRK505212-BEN E

1MRK002801-AC-10-670-1.2-PG V1 EN

Figure 16.

Transformer input module (TRM)

￭ Indicates high polarity

CT/VT-input designation according to figure 16

AI01 AI02 AI03 AI04 AI05 AI06 AI07 AI08 AI09 AI10 AI11 AI12

Current/voltage configuration (50/60 Hz)

12I, 1A

12I, 5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

1A

5A

Note that internal polarity can be adjusted by setting of analog input CT neutral direction and/or on SMAI pre-processing function blocks.

1A

5A

26 ABB


Pre-configured


1MRK002801-AC-11-670-1.2-PG V1 EN

Figure 17.

Binary input module (BIM). Input contacts named XA corresponds to rear position

X31, X41, and so on, and input contacts named XB to rear position X32, X42, and so on.

1MRK002801-AC-15-670-1.2-PG V1 EN

Figure 18.

mA input module (MIM)

1MRK505212-BEN E

1MRK002801-AC-8-670-1.2-PG V1 EN

Figure 19.

IED with basic functionality and communication interfaces

ABB 27


Pre-configured


1MRK002801-AC-7-670-1.2-PG V1 EN

Figure 20.

Power supply module (PSM)

1MRK505212-BEN E

1MRK002801-AC-12-670-1.2-PG V1 EN

Figure 21.

Binary output module (BOM). Output contacts named XA corresponds to rear position X31, X41, and so on, and output contacts named XB to rear position X32, X42, and so on.

28 ABB


Pre-configured


1MRK002801-AC-13-670-1.2-PG V1 EN

Figure 22.

Static output module (SOM)

1MRK505212-BEN E

1MRK002801-AC-14-670-1.2-PG V1 EN

Figure 23.

Binary in/out module (IOM). Input contacts named XA corresponds to rear position X31, X41, and so on, and output contacts named XB to rear position X32, X42, and so on.

ABB 29


Pre-configured


1MRK505212-BEN E

15. Technical data

General

Definitions

Reference value The specified value of an influencing factor to which are referred the characteristics of the equipment

Nominal range The range of values of an influencing quantity (factor) within which, under specified conditions, the equipment meets the specified requirements

Operative range The range of values of a given energizing quantity for which the equipment, under specified conditions, is able to perform its intended functions according to the specified requirements

Energizing quantities, rated values and limits

Analog inputs

Table 5. TRM - Energizing quantities, rated values and limits for protection transformer modules

Quantity

Current

Operative range

Permissive overload

Burden

Frequency

*)

max. 350 A for 1 s when COMBITEST test switch is included.

Rated value

I r

= 1 or 5 A

(0-100) x I r

4 × I r

cont.

100 × I r

for 1 s

*)

< 150 mVA at I r

= 5 A

< 20 mVA at I r

= 1 A f r

= 50/60 Hz

Table 6. OEM - Optical ethernet module

Quantity

Number of channels

Standard

Type of fiber

Wave length

Optical connector

Communication speed

Rated value

1 or 2

IEEE 802.3u 100BASE-FX

62.5/125 mm multimode fibre

1300 nm

Type ST

Fast Ethernet 100 MB

Auxiliary DC voltage

Table 7. PSM - Power supply module

Quantity

Auxiliary dc voltage, EL (input)

Power consumption

Auxiliary DC power in-rush

Rated value

EL = (24 - 60) V

EL = (90 - 250) V

50 W typically

< 5 A during 0.1 s

30

Nominal range

(0.2-40) × I r

± 5%

Nominal range

-

-

EL ± 20%

EL ± 20%

ABB


Pre-configured


Binary inputs and outputs

Table 8. BIM - Binary input module

Quantity

Binary inputs

DC voltage, RL

1MRK505212-BEN E

Power consumption

24/30 V, 50mA

48/60 V, 50mA

110/125 V, 50mA

220/250 V, 50mA

220/250 V, 110mA

Counter input frequency

Oscillating signal discriminator

Debounce filter

Maximum 176 binary input channels may be activated simultaneously with influencing factors within nominal range.

Rated value

16

24/30 V

48/60 V

110/125 V

220/250 V max. 0.05 W/input max. 0.1 W/input max. 0.2 W/input max. 0.4 W/input max. 0.5 W/input

10 pulses/s max

Blocking settable 1–40 Hz

Release settable 1–30 Hz

Settable 1–20ms

-

Nominal range

-

-

RL ± 20%

RL ± 20%

RL ± 20%

RL ± 20%

Table 9. BIM - Binary input module with enhanced pulse counting capabilities

Quantity

Binary inputs

DC voltage, RL

Power consumption

24/30 V

48/60 V

110/125 V

220/250 V


Balanced counter input frequency


Rated value

16

24/30 V

48/60 V

110/125 V

220/250 V max. 0.05 W/input max. 0.1 W/input max. 0.2 W/input max. 0.4 W/input

10 pulses/s max

40 pulses/s max

Blocking settable 1–40 Hz

Release settable 1–30 Hz


-

-

Nominal range

-

-

RL ± 20%

RL ± 20%

RL ± 20%

RL ± 20%

ABB 31


Pre-configured


1MRK505212-BEN E

Table 10. IOM - Binary input/output module

Quantity

Binary inputs

DC voltage, RL

Power consumption

24/30 V, 50 mA

48/60 V, 50 mA

110/125 V, 50 mA

220/250 V, 50 mA

220/250 V, 110 mA



Debounce filter


Rated value

8

24/30 V

48/60 V

110/125 V

220/250 V max. 0.05 W/input max. 0.1 W/input max. 0.2 W/input max. 0.4 W/input max. 0.5 W/input

10 pulses/s max

Blocking settable 1-40 Hz

Release settable 1-30 Hz

Settable 1-20 ms

Nominal range

-

-

RL ± 20%

RL ± 20%

RL ± 20%

RL ± 20%

Table 11. IOM - Binary input/output module contact data (reference standard: IEC 61810-2)

Function or quantity Trip and signal relays

Binary outputs

Max system voltage

Test voltage across open contact, 1 min

Current carrying capacity

Per relay, continuous

Per relay, 1 s

Per process connector pin, continuous

Making capacity at inductive load with L/R>10 ms

0.2 s

1.0 s

Making capacity at resistive load

0.2 s

1.0 s

Breaking capacity for AC, cos φ > 0.4

Breaking capacity for DC with L/R < 40 ms

Maximum capacitive load

30 A

10 A

30 A

10 A

10

250 V AC, DC

1000 V rms

8 A

10 A

12 A

-

250 V/8.0 A

48 V/1 A

110 V/0.4 A

125 V/0.35 A

220 V/0.2 A

250 V/0.15 A

32

Fast signal relays (parallel reed relay)

2

250 V DC

800 V DC

8 A

10 A

12 A

0.4 A

0.4 A

220–250 V/0.4 A

110–125 V/0.4 A

48–60 V/0.2 A

24–30 V/0.1 A

250 V/8.0 A

48 V/1 A

110 V/0.4 A

125 V/0.35 A

220 V/0.2 A

250 V/0.15 A

10 nF

ABB


Pre-configured


Table 12. IOM with MOV and IOM 220/250 V, 110mA - contact data (reference standard: IEC 61810-2)

Function or quantity

Binary outputs

Max system voltage




Per relay, 1 s


Making capacity at inductive loadwith L/R>10 ms

0.2 s

1.0 s

Making capacity at resistive load

0.2 s

1.0 s

Breaking capacity for AC, cos j >0.4

Breaking capacity for DC with L/

R < 40 ms

Maximum capacitive load -

Trip and Signal relays

IOM: 10

250 V AC, DC

250 V rms

8 A

10 A

12 A

30 A

10 A

30 A

10 A

250 V/8.0 A

48 V/1 A

110 V/0.4 A

220 V/0.2 A

250 V/0.15 A

Fast signal relays (parallel reed relay)

IOM: 2

250 V DC

250 V rms

8 A

10 A

12 A

0.4 A

0.4 A

220–250 V/0.4 A

110–125 V/0.4 A

48–60 V/0.2 A

24–30 V/0.1 A

250 V/8.0 A

48 V/1 A

110 V/0.4 A

220 V/0.2 A

250 V/0.15 A

10 nF

Table 13. SOM - Static Output Module (reference standard: IEC 61810-2): Static binary outputs

Function of quantity

Rated voltage

Number of outputs

Impedance open state


Current carrying capacity:

Continuous

1.0s

Making capacity at capacitive load with the maximum capacitance of 0.2 μF :

0.2s

1.0s

Breaking capacity for DC with L/R ≤ 40ms

Operating time

Static binary output trip

5A

10A

48 - 60 VDC

6

~300 kΩ

No galvanic separation

30A

10A

48V / 1A

60V / 0.75A

<1ms

5A

10A

110 - 250 VDC

6

~810 kΩ

No galvanic separation

30A

10A

110V / 0.4A

125V / 0.35A

220V / 0.2A

250V / 0.15A

<1ms

ABB

1MRK505212-BEN E

33


Pre-configured


1MRK505212-BEN E

Table 14. SOM - Static Output module data (reference standard: IEC 61810-2): Electromechanical relay outputs

Function of quantity

Max system voltage

Number of outputs


Current carrying capacity:

Continuous

1.0s

Making capacity at capacitive load with the maximum capacitance of

0.2 μF:

0.2s

1.0s

Breaking capacity for DC with L/R ≤ 40ms

Trip and signal relays

250V AC/DC

6

1000V rms

8A

10A

30A

10A

48V / 1A

110V / 0.4A

125V / 0.35A

220V / 0.2A

250V / 0.15A

Table 15. BOM - Binary output module contact data (reference standard: IEC 61810-2)

Function or quantity

Binary outputs

Max system voltage




Per relay, 1 s


Making capacity at inductive load with L/R>10 ms

0.2 s

1.0 s

Breaking capacity for AC, cos j>0.4

Breaking capacity for DC with L/R < 40 ms

Trip and Signal relays

24

250 V AC, DC

1000 V rms

8 A

10 A

12 A

30 A

10 A

250 V/8.0 A

48 V/1 A

110 V/0.4 A

125 V/0.35 A

220 V/0.2 A

250 V/0.15 A

Influencing factors

Table 16. Temperature and humidity influence

Parameter

Ambient temperature, operate value

Relative humidity

Operative range

Storage temperature

Reference value

+20 °C

10%-90%

0%-95%

-40 °C to +70 °C

34

-

Nominal range

-10 °C to +55 °C

10%-90%

-

-

Influence

0.02% /°C

ABB


Pre-configured


1MRK505212-BEN E

Table 17. Auxiliary DC supply voltage influence on functionality during operation

Dependence on Reference value Within nominal range

15% of EL Ripple, in DC auxiliary voltage

Operative range

Auxiliary voltage dependence, operate value

Interrupted auxiliary DC voltage

Interruption interval

0–50 ms max. 2%

Full wave rectified

± 20% of EL

24-60 V DC ± 20%

90-250 V DC ± 20%

0–∞ s

Restart time

Influence

0.01% /%

0.01% /%

No restart

Correct behaviour at power down

<300 s

Table 18. Frequency influence (reference standard: IEC 60255–1)

Dependence on

Frequency dependence, operate value

Influence

± 1.0% / Hz

Frequency dependence for differential protection

Harmonic frequency dependence (20% content)

Harmonic frequency dependence for differential protection (10% content)

Within nominal range f r

± 2.5 Hz for 50 Hz f r



± 3.0 Hz for 50 Hz

2nd, 3rd and 5th harmonic of f r

2nd, 3rd and 5th harmonic of f r

± 2.0% / Hz

± 1.0%

± 6.0%

ABB 35


Pre-configured


Type tests according to standards

Table 19. Electromagnetic compatibility

Test

1 MHz burst disturbance

100 kHz slow damped oscillatory wave immunity test

Ring wave immunity test, 100 kHz

Surge withstand capability test

Electrostatic discharge

Direct application

Indirect application

Electrostatic discharge

Direct application

Indirect application

Fast transient disturbance

Surge immunity test

Power frequency immunity test

Conducted common mode immunity test

Power frequency magnetic field test

Damped oscillatory magnetic field test

Radiated electromagnetic field disturbance

Radiated electromagnetic field disturbance

Conducted electromagnetic field disturbance

Radiated emission

Conducted emission

Table 20. Insulation

Test

Dielectric test

Impulse voltage test

Insulation resistance

1MRK505212-BEN E

Type test values

2.5 kV

2.5 kV

2-4 kV

2.5 kV, oscillatory

4.0 kV, fast transient

15 kV air discharge

8 kV contact discharge


15 kV air discharge



4 kV

1-2 kV, 1.2/50 ms high energy

150-300 V, 50 Hz

15 Hz-150 kHz

1000 A/m, 3 s

100 A/m, cont.

100 A/m

20 V/m, 80-1000 MHz

1.4-2.7 GHz

35 V/m

26-1000 MHz

10 V, 0.15-80 MHz

30-1000 MHz

0.15-30 MHz

Reference standards

IEC 60255-22-1

IEC 61000-4-18, Class III

IEC 61000-4-12, Class IV

IEEE/ANSI C37.90.1



IEEE/ANSI C37.90.1

IEC 60255-22-4, Class A

IEC 60255-22-5

IEC 60255-22-7, Class A


IEC 61000-4-8, Class V

IEC 61000-4-10, Class V

IEC 60255-22-3

IEEE/ANSI C37.90.2

IEC 60255-22-6

IEC 60255-25

IEC 60255-25

Type test values

2.0 kV AC, 1 min.

5 kV, 1.2/50 ms, 0.5 J

>100 MW at 500 VDC

Reference standard

IEC 60255-5

36 ABB


Pre-configured


1MRK505212-BEN E

Table 21. Environmental tests

Test

Cold test

Storage test

Dry heat test

Damp heat test, steady state

Damp heat test, cyclic

Table 22. CE compliance

Test

Immunity

Emissivity

Low voltage directive

Table 23. Mechanical tests

Test

Vibration response test

Vibration endurance test

Shock response test

Shock withstand test

Bump test

Seismic test

Type test value

Test Ad for 16 h at -25°C

Test Ad for 16 h at -40°C

Test Bd for 16 h at +70°C

Test Ca for 4 days at +40 °C and humidity 93%

Test Db for 6 cycles at +25 to +55 °C and humidity 93 to 95% (1 cycle =

24 hours)

Reference standard

IEC 60068-2-1

IEC 60068-2-1

IEC 60068-2-2

IEC 60068-2-78

IEC 60068-2-30

Type test values

Class II

Class I

Class II

Class I

Class I

Class II

According to

EN 50263

EN 50263

EN 50178

Reference standards

IEC 60255-21-1

IEC 60255-21-1

IEC 60255-21-2

IEC 60255-21-2

IEC 60255-21-2

IEC 60255-21-3

ABB 37


Pre-configured


Differential protection

Table 24. Busbar differential protection

Function

Operating characteristic

Range or value

S=0.53 fixed

Reset ratio > 95%

Differential current operating level (1-100000) A

Sensitive differential operation level

Check zone operation level

(1-100000) A

(0-100000) A

Check zone slope

Timers

Timers

Operate time

Reset time

Critical impulse time

(0.0-0.9)

(0.000-60.000) s

(0.00-6000.00) s

19 ms typically at 0 to 2 x I d





-

-

Accuracy

±

2.0% of I r

for I < I r

± 2.0% of I for I > I r

-

± 2.0% of I r

for I < I r

±

2.0% of I for I > I r

± 2.0% of I r

for I < I r

± 2.0% of I for I < I r

±

2.0% of I r

for I < I r

±

2.0% of I for I > I r

-

±

0.5% ± 10 ms

-

±

0.5% ± 10 ms

1MRK505212-BEN E

38 ABB


Pre-configured


Current protection

Table 25. Four step phase overcurrent protection OC4PTOC

Function

Operate current

Setting range

(5-2500)% of lBase

Reset ratio

Min. operating current

> 95% at (50–2500)% of lBase

(1-10000)% of lBase

Relay characteristic angle (RCA)

Relay operating angle (ROA)

2nd harmonic blocking

Independent time delay at 0 to 2 x

I set

Minimum operate time

(40.0–65.0) degrees

(40.0–89.0) degrees

(5–100)% of fundamental

(0.000-60.000) s

(0.000-60.000) s

Inverse characteristics, see

table 63

, table 64 and table 65

Operate time, start non-directional at 0 to 2 x I set

Reset time, start non-directional at

2 to 0 x I set


Impulse margin time

16 curve types

Min. = 15 ms

Max. = 30 ms

Min. = 15 ms

Max. = 30 ms

10 ms typically at 0 to 2 x I set

15 ms typically

Table 26. Four step single phase overcurrent protection PH4SPTOC

Function

Operate current

Setting range

(1-2500)% of l base

Reset ratio

Second harmonic blocking

Independent time delay

Minimum operate time

Inverse characteristics, see

table 63

and table 64

Operate time, start function

Reset time, start function


Impulse margin time

> 95%

(5–100)% of fundamental

(0.000-60.000) s

(0.000-60.000) s

19 curve types

25 ms typically at 0 to 2 x I



15 ms typically set set set

-

-

-

-

Accuracy

-

± 1.0% of I r

at I £ I r

±

1.0% of I at I > I r

± 2.0% of I r

± 0.5% ± 10 ms

± 0.5% ± 10 ms

See table 63 and table

64

1MRK505212-BEN E

-

-

Accuracy

±

1.0% of I r

at I ≤ I r

± 1.0% of I at I > I r

-

± 1.0% of I r

at I ≤ I r

±


± 2.0 degrees

± 2.0 degrees

± 2.0% of I r

±

0.2 % or ± 35 ms whichever is greater

± 2.0 % or ± 40 ms whichever is greater

See table

63

, table 64 and table 65

ABB 39


Pre-configured


Table 27. Breaker failure protection CCRBRF

Function

Operate phase current

Reset ratio, phase current

Operate residual current

Reset ratio, residual current

Phase current level for blocking of contact function

Range or value

(5-200)% of lBase

> 95%

(2-200)% of lBase

> 95%

(5-200)% of lBase

Reset ratio

Timers

Operate time for current detection

Reset time for current detection

> 95%

(0.000-60.000) s

10 ms typically

15 ms maximum

Table 28. Breaker failure protection, single phase version CCSRBRF

Function

Operate phase current

Range or value

(5-200)% of lBase

Reset ratio, phase current

Phase current level for blocking of contact function

Reset ratio

Timers

Operate time for current detection

Reset time for current detection

> 95%

(5-200)% of

> 95% lBase

(0.000-60.000) s

10 ms typically

15 ms maximum

1MRK505212-BEN E

Accuracy

-

± 1.0% of I r

at I £ I r

±


-

± 1.0% of I r

at I £ I r

±


±

1.0% of I r

at I £ I r

± 1.0% of I at I > I r

-

-

-

±

0.5% ±10 ms

Accuracy

±

1.0% of I r

at I £ I r

± 1.0% of I at I > I r

-

± 1.0% of I r

at I £ I r

±


-

-

-

± 0.5% ± 10 ms

40 ABB


Pre-configured


Control

Table 29. Autorecloser SMBRREC

Function

Number of autoreclosing shots

Autoreclosing open time: shot 1 - t1 1Ph shot 1 - t1 2Ph shot 1 - t1 3PhHS shot 1 - t1 3PhDld shot 2 - t2 shot 3 - t3 shot 4 - t4 shot 5 - t5

Extended autorecloser open time

Autorecloser maximum wait time for sync

Maximum trip pulse duration

Inhibit reset time

Reclaim time

Minimum time CB must be closed before AR becomes ready for autoreclosing cycle

Circuit breaker closing pulse length

CB check time before unsuccessful

Wait for master release

Wait time after close command before proceeding to next shot

Range or value

1 - 5

(0.000-60.000) s

(0.00-6000.00) s

(0.000-60.000) s

(0.00-6000.00) s

(0.000-60.000) s

(0.000-60.000) s

(0.00-6000.00) s

(0.00-6000.00) s

(0.000-60.000) s

(0.00-6000.00) s

(0.00-6000.00) s

(0.000-60.000) s

1MRK505212-BEN E

Accuracy

-

± 0.5% ± 10 ms

ABB 41


Pre-configured


Logic

Table 30. Configurable logic blocks

Logic block Quantity with update rate

LogicAND

LogicOR

LogicXOR

LogicInverter

LogicSRMemory

LogicRSMemory

LogicGate

LogicTimer

LogicPulseTimer

LogicTimerSet

LogicLoopDelay

Boolean 16 to Integer 4

Boolean 16 to integer with Logic Node

4

Integer to Boolean 16 4

Integer to Boolean 16 with Logic Node

4

15

15

15

15 fast

15

15

15

90

90

15

45

4

4

4

4

15

15

15

15 medium

15

15

15

90

90

15

45

8

8 normal

10

10

10

100

100

10

50

8

8

10

10

10

10

Range or value

-

-

-

-

-

-

-

-

-

-

-

(0.000–90000.000) s

(0.000–90000.000) s

(0.000–90000.000) s

(0.000–90000.000) s

1MRK505212-BEN E

Accuracy

-

-

-

-

-

-

-

-

-

-

-

± 0.5% ± 10 ms

± 0.5% ± 10 ms

± 0.5% ± 10 ms

± 0.5% ± 10 ms

42 ABB


Pre-configured


Monitoring

Table 31. Measurements CVMMXN

Function

Frequency

Connected current

Range or value

(0.95-1.05) × f r

(0.2-4.0) × I r

Table 32. Phase current measurement CMMXU

Function

Current

Range or value

(0.1-4.0) × I r

Phase angle (0.1–4.0) x I r

Table 33. Phase-phase voltage measurement VMMXU

Function

Voltage

Range or value

(10 to 300) V

Phase angle (10 to 300) V

Table 34. Phase-neutral voltage measurement VNMMXU

Function

Voltage

Range or value

(10 to 300) V

Phase angle (10 to 300) V

Table 35. Current sequence component measurement CMSQI

Function

Current positive sequence, I1

Three phase settings

Current zero sequence, 3I0


Current negative sequence, I2


Phase angle

Range or value

(0.1–4.0) × I r

(0.1–1.0) × I

(0.1–1.0) × I

(0.1–4.0) × I r r r

Accuracy

±

2.0 mHz

±

0.5% of I r

at I £ I r

± 0.5% of I at I > I r

Accuracy

± 0.2% of I r

at I ≤ 0.5 × I

±

0.2% of I at I > 0.5 × I r r

±

0.5° at 0.2 × I r

< I < 0.5 × I r

± 0.2° at 0.5 × I r

≤ I < 4.0 × I r

Accuracy

± 0.3% of U at U ≤ 50 V

±

0.2% of U at U > 50 V

±

0.3° at U ≤ 50 V

± 0.2° at U > 50 V

Accuracy

± 0.3% of U at U ≤ 50 V

±

0.2% of U at U > 50 V

±

0.3° at U ≤ 50 V

± 0.2° at U > 50 V

Accuracy

± 0.2% of I r

at I ≤ 0.5 × I

±

0.2% of I at I > 0.5 × I r r

±

0.2% of I r

at I ≤ 0.5 × I

±

0.2% of I at I > 0.5 × I r r

±

0.2% of I r

at I ≤ 0.5 × I

± 0.2% of I at I > 0.5 × I r r

± 0.5° at 0.2 × I r

< I < 0.5 × I r

±

0.2° at 0.5 × I r

≤ I < 4.0 × I r

1MRK505212-BEN E

ABB 43


Pre-configured


1MRK505212-BEN E

Table 36. Voltage sequence measurement VMSQI

Function

Voltage positive sequence, U1

Voltage zero sequence, 3U0

Voltage negative sequence, U2

Phase angle

Range or value

(10 to 300) V

(10 to 300) V

(10 to 300) V

(10 to 300) V

Accuracy

± 0.3% of U at U ≤ 50 V

±

0.2% of U at U > 50 V

±

0.3% of U at U ≤ 50 V

±

0.2% of U at U > 50 V

±

0.3% of U at U ≤ 50 V

± 0.2% of U at U > 50 V

± 0.3° at U ≤ 50 V

±

0.2° at U > 50 V

Table 37. Event counter CNTGGIO

Function

Counter value

Max. count up speed

Table 38. Disturbance report DRPRDRE

Function

Pre-fault time

Post-fault time

Limit time

Maximum number of recordings

Time tagging resolution

Maximum number of analog inputs

Range or value

0-100000

10 pulses/s (50% duty cycle)

Maximum number of binary inputs

Maximum number of phasors in the Trip Value recorder per recording

Maximum number of indications in a disturbance report

Maximum number of events in the Event recording per recording

Maximum number of events in the Event list

Maximum total recording time (3.4 s recording time and maximum number of channels, typical value)

Sampling rate

Recording bandwidth

Table 39. Event list

Function

Buffer capacity

Resolution

Accuracy

Maximum number of events in the list

-

-

Accuracy

Value

1000

Range or value

(0.05–9.90) s

(0.1–10.0) s

(0.5–10.0) s

100, first in - first out

1 ms

30 + 10 (external + internally derived)

96

30

96

150

1000, first in - first out

340 seconds (100 recordings) at

50 Hz, 280 seconds (80 recordings) at 60 Hz

1 kHz at 50 Hz

1.2 kHz at 60 Hz

(5-300) Hz

1 ms

Depending on time synchronizing

-

-

-

-

-

-

-

-

Accuracy

-

-

-

-

-

See table

59

44 ABB


Pre-configured


1MRK505212-BEN E

Table 40. Indications

Function

Buffer capacity Maximum number of indications presented for single disturbance

Maximum number of recorded disturbances

Table 41. Event recorder

Function

Buffer capacity Maximum number of events in disturbance report

Maximum number of disturbance reports

Resolution

Accuracy

Table 42. Trip value recorder

Function

Buffer capacity Maximum number of analog inputs


Table 43. Disturbance recorder

Function

Buffer capacity Maximum number of analog inputs

Maximum number of binary inputs


Maximum total recording time (3.4 s recording time and maximum number of channels, typical value)

Value

40

96

100

340 seconds (100 recordings) at 50 Hz

280 seconds (80 recordings) at 60 Hz

Value

96

100

Value

150

100

1 ms

Depending on time synchronizing

Value

30

100

ABB 45


Pre-configured


Station communication

Table 44. IEC 61850-8-1 communication protocol

Function

Protocol

Communication speed for the IEDs

Protocol


Protocol


Protocol


Value

IEC 61850-8-1

100BASE-FX

IEC 608–5–103

9600 or 19200 Bd

DNP3.0

300–19200 Bd

TCP/IP, Ethernet

100 Mbit/s

Table 45. LON communication protocol

Function

Protocol

Communication speed

Value

LON

1.25 Mbit/s

Table 46. SPA communication protocol

Function

Protocol

Communication speed

Slave number

Value

SPA

300, 1200, 2400, 4800, 9600, 19200 or 38400 Bd

1 to 899

Table 47. IEC60870-5-103 communication protocol

Function

Protocol

Communication speed

Value

IEC 60870-5-103

9600, 19200 Bd

Table 48. SLM – LON port

Quantity Range or value

Optical connector

Fibre, optical budget

Glass fibre: type ST

Plastic fibre: type HFBR snap-in

Glass fibre: 11 dB (1000 m typically *)

Plastic fibre: 7 dB (10 m typically *)

Fibre diameter Glass fibre: 62.5/125 mm

Plastic fibre: 1 mm

*) depending on optical budget calculation

1MRK505212-BEN E

46 ABB


Pre-configured


Table 49. SLM – SPA/IEC 60870-5-103/DNP3 port

Quantity Range or value

Optical connector

Fibre, optical budget

Glass fibre: type ST

Plastic fibre: type HFBR snap-in

Glass fibre: 11 dB (3000ft/1000 m typically *)

Plastic fibre: 7 dB (80ft/25 m typically *)

Fibre diameter Glass fibre: 62.5/125 mm

Plastic fibre: 1 mm


Table 50. Galvanic RS485 communication module

Quantity

Communication speed

External connectors

Range or value

2400–19200 bauds

RS-485 6-pole connector

Soft ground 2-pole connector

Table 51. IEC 62439-3 Edition 1 and Edition 2 parallel redundancy protocol

Function

Protocol

Communication speed

Value

IEC 61850-8-1

100 Base-FX

1MRK505212-BEN E

ABB 47


Pre-configured


1MRK505212-BEN E

Remote communication

Table 52. Line data communication module

Characteristic Range or value

Type of LDCM Short range (SR) Medium range (MR) Long range (LR)

Type of fibre

Wave length

Optical budget

Graded-index multimode 62.5/125 mm,

Graded-index multimode 50/125 mm

Graded-index multimode

62.5/125 µm or

50/125 µm

850 nm

13 dB (typical distance about 3 km *)

9 dB (typical distance about 2 km *)

Singlemode 9/125 µm Singlemode 9/125 µm

1310 nm

22 dB (typical distance 80 km *)

Optical connector

Protocol

Data transmission

Transmission rate / Data rate

Type ST

C37.94

Synchronous

2 Mb/s / 64 kbit/s

Type FC/PC

C37.94

implementation **)

Synchronous

2 Mb/s / 64 kbit/s

Clock source Internal or derived from received signal

Internal or derived from received signal


**) C37.94 originally defined just for multimode; using same header, configuration and data format as C37.94

1550 nm

26 dB (typical distance 110 km *)

Type FC/PC

C37.94 implementation **)

Synchronous

2 Mb/s / 64 kbit/s

Internal or derived from received signal

48 ABB


Pre-configured


1MRK505212-BEN E

Hardware

IED

Table 53. Case

Material

Front plate

Surface treatment

Finish

Steel sheet

Steel sheet profile with cut-out for HMI

Aluzink preplated steel

Light grey (RAL 7035)

Table 54. Water and dust protection level according to IEC 60529

Front

Sides, top and bottom

Rear side

IP40 (IP54 with sealing strip)

IP20

IP20 with screw compression type

IP10 with ring lug terminals

Table 55. Weight

Case size

6U, 1/2 x 19”

6U, 3/4 x 19”

6U, 1/1 x 19”

Connection system

Table 56. CT circuit connectors

Connector type

Screw compression type

Weight

£ 10 kg

£ 15 kg

£ 18 kg

Rated voltage and current

250 V AC, 20 A

250 V AC, 20 A Terminal blocks suitable for ring lug terminals

Table 57. Binary I/O connection system

Connector type

Screw compression type

Terminal blocks suitable for ring lug terminals

Rated voltage

250 V AC

300 V AC

Maximum conductor area

4 mm

2

(AWG12)

2 x 2.5 mm

2

(2 x AWG14)

4 mm

2

(AWG12)

Maximum conductor area

2.5 mm

2

(AWG14)

2 × 1 mm

2

(2 x AWG18)

3 mm

2

(AWG14)

ABB 49


Pre-configured


1MRK505212-BEN E

Basic IED functions

Table 58. Self supervision with internal event list

Data

Recording manner

List size

Value

Continuous, event controlled

40 events, first in-first out

Table 59. Time synchronization, time tagging

Function

Time tagging resolution, events and sampled measurement values

Time tagging error with synchronization once/min (minute pulse synchronization), events and sampled measurement values

Time tagging error with SNTP synchronization, sampled measurement values

Table 60. GPS time synchronization module (GTM)

Function

Receiver

Time to reliable time reference with antenna in new position or after power loss longer than 1 month

Time to reliable time reference after a power loss longer than 48 hours

Time to reliable time reference after a power loss shorter than 48 hours

Table 61. GPS – Antenna and cable

Function

Max antenna cable attenuation

Antenna cable impedance

Lightning protection

Antenna cable connector

Range or value

–

<30 minutes

<15 minutes

<5 minutes

Accuracy

±1µs relative UTC

–

–

–

Accuracy

Value

1 ms

± 1.0 ms typically

± 1.0 ms typically

Value

26 db @ 1.6 GHz

50 ohm

Must be provided externally

SMA in receiver end

TNC in antenna end

+/-2μs

50 ABB


Pre-configured


Table 62. IRIG-B

Quantity

Number of channels IRIG-B

Number of channels PPS

Electrical connector:

Electrical connector IRIG-B

Pulse-width modulated

Amplitude modulated

– low level

– high level

Supported formats

Accuracy

Input impedance

Optical connector:

Optical connector PPS and IRIG-B

Type of fibre

Supported formats

Accuracy

1MRK505212-BEN E

Rated value

1

1

BNC

5 Vpp

1-3 Vpp

3 x low level, max 9 Vpp

IRIG-B 00x, IRIG-B 12x

+/-10μs for IRIG-B 00x and +/-100μs for IRIG-B 12x

100 k ohm

Type ST

62.5/125 μm multimode fibre

IRIG-B 00x, PPS

+/- 2μs

ABB 51


Pre-configured


Inverse characteristic

Table 63. ANSI Inverse time characteristics

Function

Operating characteristic:

Range or value k = (0.05-999) in steps of 0.01

t

=

æ

ç

I

A

(

P

-

1

)

+

B

ö

÷

×

k

EQUATION1249-SMALL V1 EN

Reset characteristic:

t

=

I tr

( )

×

k


I = I measured

/I set

ANSI Extremely Inverse

ANSI Very inverse

ANSI Normal Inverse

ANSI Moderately Inverse

ANSI Long Time Extremely Inverse

ANSI Long Time Very Inverse

ANSI Long Time Inverse

A=28.2, B=0.1217, P=2.0 , tr=29.1

A=19.61, B=0.491, P=2.0 , tr=21.6

A=0.0086, B=0.0185, P=0.02, tr=0.46

A=0.0515, B=0.1140, P=0.02, tr=4.85

A=64.07, B=0.250, P=2.0, tr=30

A=28.55, B=0.712, P=2.0, tr=13.46

A=0.086, B=0.185, P=0.02, tr=4.6

1MRK505212-BEN E

-

Accuracy

ANSI/IEEE C37.112, 5%

+ 40 ms

52 ABB


Pre-configured


Table 64. IEC Inverse time characteristics

Function

Operating characteristic:

t

=

æ

ç

I

A

(

P

-

1

)

ö

÷

×

k


I = I measured

/I set

Time delay to reset, IEC inverse time

IEC Normal Inverse

IEC Very inverse

IEC Inverse

IEC Extremely inverse

IEC Short time inverse

IEC Long time inverse

Programmable characteristic

Operate characteristic:

t

=

æ

ç

I

(

P

A

-

C

)

+

B

ö

÷

×

k


Reset characteristic:


(0.000-60.000) s

A=0.14, P=0.02

A=13.5, P=1.0

A=0.14, P=0.02

A=80.0, P=2.0

A=0.05, P=0.04

A=120, P=1.0

k = (0.05-999) in steps of 0.01

A=(0.005-200.000) in steps of 0.001

B=(0.00-20.00) in steps of 0.01

C=(0.1-10.0) in steps of 0.1

P=(0.005-3.000) in steps of 0.001

TR=(0.005-100.000) in steps of 0.001

CR=(0.1-10.0) in steps of 0.1

PR=(0.005-3.000) in steps of 0.001

t

=

(

I

PR

TR

-

CR

)

×

k


I = I measured

/I set

Table 65. RI and RD type inverse time characteristics

Function

RI type inverse characteristic


t

=

1

0.339

-

0.236

I

×

k


I = I measured

/I set

RD type logarithmic inverse characteristic k = (0.05-999) in steps of 0.01

t

= 5.8

-

æ

1.35

×

In

I k


I = I measured

/I set

ABB

Accuracy

IEC 60255-151, 5% + 40 ms

1MRK505212-BEN E

-

Accuracy

± 0.5% of set time ± 10 ms

IEC 60255-151, 5% + 40 ms

53


Pre-configured


1MRK505212-BEN E

16. Ordering

Guidelines

Carefully read and follow the set of rules to ensure problem-free order management.

Please refer to the available functions table for included application functions.

PCM600 can be used to make changes and/or additions to the delivered factory configuration of the pre-configured.

10

To obtain the complete ordering code, please combine code from the tables, as given in the example below.

Example code: REB670*1.2-A20X01-C06-X0-A-A-B-A-A2-X0-CAX-XXX-XD. Using the code of each position #1-12 specified as REB670*1-2 2-3 3 3-4-5-6-7 7-8-9 9

9-10 10 10 10 10 10 10 10 10 10 10-11 11 11 11 11 11-12 12

REB670*

# 1 - 2

-

- 3

-

- 4

-

- 5

-

6 - 7

-

- 8

.

- 9

- -

-

- 11

.

- 12

-

SOFTWARE

Version number

Version no

Configuration alternatives

3 phase, 4 bays

3 phase, 8 bays

1 phase, 12 bays, 1/2 19" case

1 phase, 12 bays, 1/1 19" case

1 phase, 24 bays

ACT configuration

Simple station layout, 1 1/2 CB, 2 CB, 1 CB, b-contacts, BBP only

Double busbar - 1 CB, a and b contacts, BBP only

Double busbar - 1 CB, a and b contacts, BBP, EnFP

Software options

No option

Four step phase overcurrent protection, 4 bays

Four step phase overcurrent protection, 8 bays

Four step single phase overcurrent protection, 12 bays

Four step single phase overcurrent protection, 24 bays

Breaker failure protection, 4 bays

Breaker failure protection, 8 bays

Breaker failure protection, 12 bays, single phase

Breaker failure protection, 24 bays, single phase

Autorecloser, 2 circuit breakers

IEC 62439-3 Edition 1, parallel redundancy protocol

IEC 62439-3 Edition 2, parallel redundancy protocol

Selection for position #1.

#1

1.2

Notes and Rules


A20

A31

B20

B21

B31

#2 Notes and Rules

X01

X02 Note: Only for A31, B21 and B31

X03 Note: Only for A31, B21 and B31

Note: One each of Breaker failure protection and Overcurrent protection must be ordered

Selection for position #3

X00

#3

C06

C07

C08

C09

C10

C11

C12

C13

H05

Notes and Rules

All fields in the ordering form do not need to be filled in

Note: Only for A20

Note: Only for A31

Note: Only for B20 and B21

Note: Only for B31

Note: Only for A20

Note: Only for A31

Note: Only for B20 and B21

Note: Only for B31

P01 Note:Require 2-channel OEM

P02

54 ABB


Pre-configured


1MRK505212-BEN E

First local HMI user dialogue language

HMI language, English IEC

HMI language, English US

Additional local HMI user dialogue language

HMI language, German

HMI language, Russian

HMI language, French

HMI language, Spanish

HMI language, Polish

HMI language, Hungarian

HMI language, Czech

HMI language, Swedish

Casing

1/2 x 19" case

3/4 x 19" case 1 TRM

1/1 x 19" case 2 TRM slots

Mounting details with IP40 of protection from the front

No mounting kit included

19" rack mounting kit for 1/2 x 19" case of 2xRHGS6 or RHGS12

19" rack mounting kit for 3/4 x 19" case or 3xRGHS6

19" rack mounting kit for 1/1 x 19" case

Wall mounting kit


#4

B1

B2

A1

A2

A3

A4

A6

A7

A8

A9


#5

A

B

E

Notes and Rules

Notes and Rules

Note: Only for A20/B20


Note: Only for A31/B21/B31

Flush mounting kit

Flush mounting kit + IP54 mounting seal

Connection type for Power supply, Input/output and Communication modules

Compression terminals

Auxiliary power supply

24-60 VDC

90-250 VDC

Human machine hardware interface

Small size - text only, IEC keypad symbols

Medium size - graphic display, IEC keypad symbols

Medium size - graphic display, ANSI keypad symbols

Connection type for Analog modules

Compression terminals

Ringlug terminals

Analog system

First TRM, 12I, 1A

First TRM, 12I, 5A

No second TRM included

Second TRM, 12I, 1A

Second TRM, 12I, 5A


E

F

#6

B

C

X

A

D

Notes and Rules



Note: Wall mounting not recommended with communication modules with fibre connection (SLM, OEM,

LDCM)


K

#7

A

B

Notes and Rules


#8

A

B

C

Notes and Rules


A

B

#9

1

2

Notes and Rules

1

2

X0 Note: A31/B31 must include a second TRM, optional in B21

ABB 55


Pre-configured


1MRK505212-BEN E

Binary input/output module, mA and time synchronization boards. Note: 1BIM and 1 BOM included.

#10 Notes and Rules

Make BIM with 50 mA inrush current the primary choice. BIM with 50 mA inrush current fulfill additional standards. As a consequence the EMC withstand capability is further increased.

BIM with 30 mA inrush current is still available.

For pulse counting, for example kWh metering, the BIM with enhanced pulse counting capabilities must be used.

Slot position (rear view)

1/2 Case with 1 TRM

3/4 Case with 1 TRM

1/1 Case with 2 TRM

No board in slot

Binary output module 24 output relays (BOM)

BIM 16 inputs, RL24-30 VDC, 30 mA








BIMp 16 inputs, RL24-30 VDC for pulse counting




IOM 8 inputs, 10+2 output, RL24-30 VDC




IOM 8 inputs, 10+2 output, RL24-30 VDC, 50 mA




IOM with MOV 8 inputs, 10-2 output, 24-30 VDC




mA input module MIM, 6 channels

SOM Static outputs module, 12 outputs, 48-60 VDC

SOM static outputs module, 12 outputs, 110-250 VDC


█

█

█

B

C

D

E

B

1

C

1

D

1

E

1

A

█

█

█ █

D

E

B

C

X

A

█

█

D

E

B

C

X

A

█

█

█

█

X

A

B

C

D

E

█

█

X

A

B

C

D

E

█

█

X

A

B

C

D

E

█

█

X

A

B

C

D

E

█

X

A

B

C

D

E

B1

C1

D1

E1

F*

G*

H*

K*

E

1

D

1

B

1

C

1

H

K

F

G

D

1

E

1

C

1

B

1

F

G

H

K

B

1

C

1

D

1

E

1

F

G

H

K

B

1

C

1

D

1

E

1

F

G

H

K

B

1

C

1

D

1

E

1

F

G

H

K

B

1

C

1

D

1

E

1

F

G

H

K

L*

M*

L

M

L L L L L L L

M M M M M M M

N*

P*

L1*

N

M1* M

1

N

M

1

N

M

1

N

M

1

N

M

1

N

M

1

N N

P P P P P P P P

L1 L1 L1 L1 L1 L1 L1 L1

M

1

M

1

Note: Max 3 positions in 1/2 rack,

8 in 3/4 rack with 1 TRM and 11 in 1/1 rack with 2 TRM

Note: Only for A20/B20. Only position X31 to X51 can be selected


█ Note: Only for A31/B21/B31

D

E

B

C

X

A

█

E

1

D

1

B

1

C

1

H

K

F F

G G

H

K

E

1

D

1

B

1

C

1

X Note: * Not in B21/B31

A Note: Maximum 4 BOM+SOM

B boards

C

D

E

Note: Basic configuration in A20,

A31 and B20 adapted for 1 BIM and 1 BOM

Note: Basic configuration in B21 and B31 adapted for 2 BIM and 1

BOM

T2*

W*

Y*

R*

T1*

N1* N

1

P1* P

1

U*

V*

U

V

N

1

P

1

U

V

N

1

P

1

U

V

P

1

N

1

U

V

N

1

P

1

U

V

P

1

N

1

U

V

N

1

P

1

U

V

N

1

P

1

U

V

W W W W W W W W

Y Y Y Y Y Y Y Y

R R R R R R R R Note: No MIM board in 1/2 case

T1 T1 T1 T1 T1 T1 T1 T1

T2 T2 T2 T2 T2 T2 T2 T2

56 ABB


Pre-configured


1MRK505212-BEN E

Remote end communication, DNP serial comm. and time synchronization modules


Available slots in 1/2 case with 1 TRM

Available slots in 3/4 case with 1 TRM

Available slots in 1/1 case with 2 TRM slots

No remote communication board included

Optical short range SR LDCM

GPS Time module GTM

IRIG-B Time synchronization module, with PPS

Galvanic RS485 communication module


G

█

█

█

X

A

S

Serial communication unit for station communication


No first communication board included

No second communication board included

Serial and LON communication module (plastic)

Serial (plastic) and LON (glass) communication module

Serial and LON communication module (glass)

Serial IEC 60870-5-103 plastic interface

Serial IEC 60870-5-103 plastic/glass interface

Serial IEC 60870-5-103 glass interface

Optical ethernet module, 1 channel glass

Optical ethernet module, 2 channel glass

█

█

█

X

A

S

G

#11

G

F

█

X

A

█

█

G

█

X

A

█

█

█

X

A

S

G G

█

X

A

S

Notes and Rules

Note: Max 1 LDCM

Note: Max 2 LDCM

Note: Max 2 LDCM


X

C

F

A

B

G

H

#12

X

E

D

Notes and Rules

Note: Optical ethernet module, 2 channel glass is not allowed together with SLM.

Guidelines

Carefully read and follow the set of rules to ensure problem-free order management. Be aware that certain functions can only be ordered in combination with other functions and that some functions require specific hardware selections.

Please refer to the available functions table for included application functions.

Accessories

External current transformer unit

Note: Only for REB670 B20, B21 and B31

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 1/1 A Quantity: 1MRK 000 643-EA

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 5/1 A

3 pcs SLCE 8–1 summation transformers on apparatus plate (2U high), 2/1 A

Quantity:

Quantity:

1MRK 000 643-FA

1MRK 000 643-GA

GPS antenna and mounting details

GPS antenna, including mounting kits

Cable for antenna, 20 m

Cable for antenna, 40 m

Quantity:

Quantity:

Quantity:

1MRK 001 640-AA

1MRK 001 665-AA

1MRK 001 665-BA

ABB 57


Pre-configured


Interface converter (for remote end data communication)

External interface converter from C37.94 to G703

External interface converter from C37.94 to G703.E1

Quantity:

Quantity:

1MRK505212-BEN E

1 2

1 2

1MRK 002 245-AA

1MRK 002 245-BA

Test switch

The test system COMBITEST intended for use with the IED

670 products is described in 1MRK 512 001-BEN and 1MRK

001024-CA. Please refer to the website: www.abb.com/substationautomation for detailed information.

Due to the high flexibility of our product and the wide variety of applications possible the test switches needs to be selected for each specific application.

Select your suitable test switch based on the available contacts arrangements shown in the reference documentation.

However our proposals for suitable variants are:

RK926 315-AV is provided with one three-phase CT input with current shorting and with sixteen trip output blocking

Protection cover

Protective cover for rear side of RHGS6, 6U, 1/4 x 19” contacts. It is suitable when external CT grounding is required both for the three-phase version and single-phase versions.

One such switch is then used per bay. With such arrangement the best possible test facilities for BBP & integrated BFP are available

Test switches type RTXP 24 is ordered separately. Please refer to Section

"Related documents"

for reference to corresponding documents.

RHGS 6 Case or RHGS 12 Case with mounted RTXP 24 and the on/off switch for dc-supply are ordered separately. Please refer to Section

"Related documents"

for reference to corresponding documents.

Quantity: 1MRK 002 420-AE

Protective cover for rear side of terminal, 6U, 1/2 x 19”

Protective cover for rear side of terminal, 6U, 3/4 x 19”

Quantity:

Quantity:

1MRK 002 420-AC

1MRK 002 420-AB

Protective cover for rear side of terminal, 6U, 1/1 x 19” Quantity: 1MRK 002 420-AA

Combiflex

Key switch for settings

Key switch for lock-out of settings via LCD-HMI

Note: To connect the key switch, leads with 10 A Combiflex socket on one end must be used.

Side-by-side mounting kit

Quantity:

Quantity:

1MRK 000 611-A

1MRK 002 420-Z

Configuration and monitoring tools

Front connection cable between LCD-HMI and PC Quantity: 1MRK 001 665-CA

58 ABB


Pre-configured


LED Label special paper A4, 1 pc

LED Label special paper Letter, 1 pc

Manuals

Note: One (1) IED Connect CD containing user documentation (Operator’s manual, Technical reference manual, Installation and commissioning manual, Application manual and Getting started guide),

Connectivity packages and LED label template is always included for each IED.

Rule: Specify additional quantity of IED Connect CD requested.

Quantity:

Quantity:

Quantity:

1MRK505212-BEN E

1MRK 002 038-CA

1MRK 002 038-DA

1MRK 002 290-AB

User documentation

Rule: Specify the number of printed manuals requested

Operator’s manual

Technical reference manual

Installation and commissioning manual

Application manual

Engineering manual, 670 series

IEC Quantity:

ANSI Quantity:

IEC Quantity:

ANSI Quantity:

IEC Quantity:

ANSI Quantity:

IEC Quantity:

ANSI Quantity:

Quantity:

1MRK 505 209-UEN

1MRK 505 209-UUS

1MRK 505 208-UEN

1MRK 505 208-UUS

1MRK 505 210-UEN

1MRK 505 210-UUS

1MRK 505 211-UEN

1MRK 505 211-UUS

1MRK 511 240-UEN

Reference information

For our reference and statistics we would be pleased to be provided with the following application data:

Country:

Station name:

End user:

Voltage level: kV

ABB 59


Pre-configured


Related documents

Documents related to REB670

Operator’s manual

Installation and commissioning manual

Technical reference manual

Application manual

Product guide pre-configured

Connection and Installation components

Test system, COMBITEST

Accessories for 670 series IEDs

670 series SPA and signal list

IEC 61850 Data objects list for 670 series

Engineering manual 670 series

Communication set-up for Relion 670 series

More information can be found on www.abb.com/substationautomation .

1MRK505212-BEN E

Identity number

1MRK 505 209-UEN

1MRK 505 210-UEN

1MRK 505 208-UEN

1MRK 505 211-UEN

1MRK 505 212-BEN

1MRK 513 003-BEN

1MRK 512 001-BEN

1MRK 514 012-BEN

1MRK 500 092-WEN

1MRK 500 091-WEN

1MRK 511 240-UEN

1MRK 505 260-UEN

60 ABB

61

Contact us

ABB AB

Substation Automation Products

SE-721 59 Västerås, Sweden

Phone

Fax

+46 (0) 21 32 50 00

+46 (0) 21 14 69 18 www.abb.com/substationautomation

ABB RELION REB670 Product manual 62 Pages

ABB RELION REB670 Product manual

Busbar protection REB670

Pre-configured

Product Guide

Contents

Sensitive differential protection

Diff Oper Level

Sensitive Oper Level s=0.53

Operate region

Sens Iin Block

Differential protection operation characteristic

I

[Primary Amps]

CTConnection

CntrlIncludes

CntrlExcludes

æ

Contact us

Key Features

Frequently Answers and Questions

What types of faults can REB670 detect?

What is the minimum pick-up value for the differential current?

Does REB670 require interposing current transformers?

Related manuals

Table of contents

ABB RELION REB670 Product manual 62 Pages

ABB RELION REB670 Product manual

Busbar protection REB670

Pre-configured

Product Guide

Contents

Sensitive differential protection

Diff Oper Level

Sensitive Oper Level s=0.53

Operate region

Sens Iin Block

Differential protection operation characteristic

I

[Primary Amps]

CTConnection

CntrlIncludes

CntrlExcludes

æ

Contact us

Key Features

Frequently Answers and Questions

What types of faults can REB670 detect?

What is the minimum pick-up value for the differential current?

Does REB670 require interposing current transformers?

Related manuals

ABB

Relion 670 series

ABB

670 REB670 2.0

ABB

Relion 670 series

ABB

IED 670

ABB

Relion 670 series

ABB

IEC 60870-5-103

ABB

PB - Phase barriers A0- A1-A2

ABB

Relion 670 series

ABB

650 Series

ABB

LON 670 Series

ABB

Relion 670 series

ABB

650 series ANSI

Table of contents