JVC HR-XVC19BUS User's Manual

JVC HR-XVC19BUS User's Manual
DVD PLAYER &
VIDEO CASSETTE RECORDER
HR-XVC18BUS
HR-XVC19SUS
INSTRUCTIONS
LPT1086-001A
Cover_HR-XVC18&19US.indd 3
05.6.10 2:00:54 PM
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK
OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
WARNING: TO PREVENT FIRE OR ELECTRIC
SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a confined
space such as a bookcase or similar unit.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the product is operated in a residential
installation. This product generates, uses, and can
radiate radio frequency energy and, if not installed and
used in accordance with the instruction manual, may
cause harmful interference to radio communications.
However, there is no guarantee that interference will
not occur in a particular installation. If this product does
cause harmful interference to radio or television reception, which can be determined by turning the product
off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the product and
receiver.
•
Connect the product into an outlet on a circuit different from that to which the receiver is connected.
•
Consult the dealer or an experienced radio/TV
technician for help.
FCC COMPLIANCE: The responsible party for this
product’s compliance is:
JVC Americas Corp.
1700 Valley Road Wayne, N.J. 07470
Phone: 973-317-5000.
CAUTION concerning the Power Cord
CAUTION:
This product employs a Laser System.
To ensure proper use of this product, please read this
owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an
authorized service center.
Performing controls, adjustments, or carrying out procedures other than those specified herein may result in
hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to
open the enclosure. Visible laser radiation when open.
DO NOT STARE INTO BEAM.
CAUTION: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled with
liquids, such as vases, should be placed on the apparatus.
CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.
2
Most appliances recommend they be placed upon a
dedicated circuit;
That is, a single outlet circuit which powers only that
appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets,
loose or damaged wall outlets, extension cords, frayed
power cords, or damaged or cracked wire insulation are
dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your
appliance, and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the appliance,
and have the cord replaced with an exact replacement
part by an authorized servicer.
Protect the power cord from physical or mechanical
abuse, such as being twisted, kinked, pinched, closed in
a door, or walked upon. Pay particular attention to plugs,
wall outlets, and the point where the cord exits the appliance.
SERIAL NUMBER:
You can find the serial number on the back of the unit.
This number is unique to this unit and not available to
others. You should record requested information here
and retain this guide as a permanent record of your purchase.
Model No. ______________________________
Serial No. ______________________________
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷
IMPORTANT SAFETY INSTRUCTIONS
CAUTION:
PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNER’S MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE REFERENCE.
This product has been designed and manufactured to assure personal safety. Improper use can result in electric
shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the following procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read these instructions. - All these safety and
operating instructions should be read before the
product is operated.
2. Keep these instructions. - The safety, operating
and use instructions should be retained for future reference.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the product.
11. Only use attachments/accessories specified by
the manufacturer.
3. Heed all warnings. - All warnings on the product
and in the operating instructions should be adhered
to.
4. Follow all instructions. - All operating and use
instructions should be followed.
5. Do not use this product near water. – For example: near a bath tub, wash bowl, kitchen sink, laundry
tub, in a wet basement; or near a swimming pool;
and other areas located near water.
6. Clean only with dry cloth. – Unplug this product
from the wall outlet before cleaning. Do not use liquid
cleaners.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over- heating. The
openings should never be blocked by placing the
product on a bed, sofa, rug or other similar surface.
This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions
have been adhered to.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold
with apparatus. When a cart is used, use caution when moving the cart/product combination
to avoid injury from tip-over.
13. Unplug this product during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the product has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the product,
the product has been exposed to rain or moisture, does not operate normally, or has been
dropped.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
3
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✸
Contents
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Moisture Condensation . . . . . . . . . . . . . . .5
Symbols Used in this Manual . . . . . . . . . .5
About the Symbol Display . . . . . . . . . . .5
Notes on Discs . . . . . . . . . . . . . . . . . . . . . .5
Types of Playable Discs . . . . . . . . . . . . . .6
Disc-related terms . . . . . . . . . . . . . . . . . . .6
Regional Code . . . . . . . . . . . . . . . . . . . . . . .7
Notes on Regional Codes . . . . . . . . . . . . . .7
Notes on Copyrights . . . . . . . . . . . . . . . . . .7
Notice for Progressive Scan Use . . . . . . . .7
About the Remote Control . . . . . . . . . . . . .7
Selecting the Viewing Source . . . . . . . . . .7
Front Panel . . . . . . . . . . . . . . . . . . . . . . . . .8
Remote Control . . . . . . . . . . . . . . . . . . . . . .9
Rear Panel . . . . . . . . . . . . . . . . . . . . . . . . .10
Preparation . . . . . . . . . . . . . . . . . . . .10
Connecting an Antenna or Cable TV . . . .11
Basic TV Connections . . . . . . . . . . . .11-12
Optional TV Connections . . . . . . . . . . . .12
Audio Connection for DVD . . . . . . . . .12-13
Initial Settings - VCR . . . . . . . . . . . . . .14-15
General Operation . . . . . . . . . . . . . . . . .14
CLOCK . . . . . . . . . . . . . . . . . . . . . . . . . .14
• Auto Clock Set . . . . . . . . . . . . . . . . . .14
• Manual Clock Set . . . . . . . . . . . . . . . .14
PROGRAM . . . . . . . . . . . . . . . . . . . . . . .14
TUNING . . . . . . . . . . . . . . . . . . . . . . . . .15
• Auto Channel Programming . . . . . . . .15
• To Add or Erase Channels . . . . . . . . .15
SETUP . . . . . . . . . . . . . . . . . . . . . . . . . .15
• FUNCTION OSD . . . . . . . . . . . . . . . .15
• AUDIO MODE . . . . . . . . . . . . . . . . . .15
• BROADCAST TYPE
(STEREO / SAP / MONO) . . . . . . . . . .15
• AUDIO OUTPUT
(STEREO / LEFT / RIGHT) . . . . . . . .15
Initial Settings - DVD . . . . . . . . . . . . . .16-19
General Operation . . . . . . . . . . . . . . . . .16
LANGUAGE . . . . . . . . . . . . . . . . . . . . . .16
DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . .17
AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . .18
OTHERS . . . . . . . . . . . . . . . . . . . . . . . . .19
Operation . . . . . . . . . . . . . . . . . . . . .20
VCR Tape Playback . . . . . . . . . . . . . .20-21
Basic Instructions . . . . . . . . . . . . . . . . . . .20
Auto Tracking . . . . . . . . . . . . . . . . . . . . . .20
Manual Tracking . . . . . . . . . . . . . . . . . . .20
Search . . . . . . . . . . . . . . . . . . . . . . . . . . .20
Still Picture and Frame-by-Frame Playback . .20
Slow Motion . . . . . . . . . . . . . . . . . . . . . . .21
CM SKIP (Commercial Skip) . . . . . . . . . .21
VHS Hi-Fi Stereo / MTS Broadcast . . . . .21
Hi-Fi Stereo Audio Sound . . . . . . . . . . . .21
MTS (Multi-Channel TV Sound) . . . . . . . .21
4
VCR Tape Recording . . . . . . . . . . . . .22-25
Basic Instructions . . . . . . . . . . . . . . . . . . .22
Timer Recording . . . . . . . . . . . . . . . .22-23
Instant Timer Recording . . . . . . . . . . . . .24
Recording from External Components . .24
Copying from DVD to VCR . . . . . . . . . . .25
On-Screen Display - VCR . . . . . . . . . . . .25
Additional VCR Information . . . . . . . . . . .26
VCR Auto Play System . . . . . . . . . . . . . .26
S-VHS Quasi Playback (SQPB) . . . . . . .26
Easy Information . . . . . . . . . . . . . . . . . . .26
Playing a DVD or Video CD . . . . . . . . .27-29
Playback Setup . . . . . . . . . . . . . . . . . . . .27
General Features . . . . . . . . . . . . . . . .27-29
• Moving to another TITLE . . . . . . . . . .27
• Moving to another CHAPTER . . . . . .27
• Slow Motion . . . . . . . . . . . . . . . . . . . . .27
• Still Picture and Frame-by-Frame Playback . .28
• Search . . . . . . . . . . . . . . . . . . . . . . . . .28
• Time Search . . . . . . . . . . . . . . . . . . . .28
• Marker Search . . . . . . . . . . . . . . . . . . .28
• Repeat . . . . . . . . . . . . . . . . . . . . . . . . .28
• Repeat A-B . . . . . . . . . . . . . . . . . . . . .28
• Zoom . . . . . . . . . . . . . . . . . . . . . . . . . .28
• Changing the Audio Channel . . . . . . .29
• Last Scene Memory . . . . . . . . . . . . . .29
• Screen Saver . . . . . . . . . . . . . . . . . . .29
Special DVD Features . . . . . . . . . . . . . .29
• Checking the contents of DVD discs:
Menus . . . . . . . . . . . . . . . . . . . . . . . . .29
• Title Menu . . . . . . . . . . . . . . . . . . . . .29
• Disc Menu . . . . . . . . . . . . . . . . . . . . .29
• Camera Angle
. . . . . . . . . . . . . . . . .29
• Changing the Audio Language . . . . . .29
• Subtitles . . . . . . . . . . . . . . . . . . . . . .29
On-Screen Display - DVD . . . . . . . . . . . .30
Maintenance and Service . . . . . . . . . . . . .30
Playing an Audio CD Disc . . . . . . . . . . . .31
Audio CD Disc Features . . . . . . . . . . . . . .31
• Pause . . . . . . . . . . . . . . . . . . . . . . . .31
• Moving to another Track
. . . . . . . . .31
• Repeat Track / All / Off . . . . . . . . . . . .31
• Search . . . . . . . . . . . . . . . . . . . . . . . . .32
• Random . . . . . . . . . . . . . . . . . . . . . . . .32
• Repeat A-B . . . . . . . . . . . . . . . . . . . . .32
Programmed Playback . . . . . . . . . . . . . .32
Viewing a JPEG Disc . . . . . . . . . . . . . . .34
Slide Show . . . . . . . . . . . . . . . . . . . . . . .34
Still Picture . . . . . . . . . . . . . . . . . . . . . . . .34
Moving to another File . . . . . . . . . . . . . .34
Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
To rotate picture . . . . . . . . . . . . . . . . . . . .34
Reference . . . . . . . . . . . . . . . . . . . . .35
Language Codes . . . . . . . . . . . . . . . . . . . .35
Area Codes . . . . . . . . . . . . . . . . . . . . . . . .35
Troubleshooting . . . . . . . . . . . . . . . . .36-37
Specifications . . . . . . . . . . . . . . . . . . . . . .38
Warranty (Only in U.S.A.) . . . . . . . . . . . . .39
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✹
Introduction
To ensure proper use of this product, please read
this owner’s manual carefully and retain for future
reference.
This manual provides information on the operation
and maintenance of your DVD+VCR. Should the
unit require service, contact an Authorized Service
Center.
Moisture Condensation
Never operate the DVD+VCR immediately after
moving it from a cold location to a warm location.
Leave it unplugged for two or three hours without
operating it.
If you use the DVD+VCR in such a situation, it
may damage discs/tapes and internal parts.
About the
Symbol Display
“ ” may appear on your TV display during operation and indicates that the function is not permitted by this unit or the disc or not available at that
time.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that fingerprints do not
get on the surface. Never stick paper or tape on
the disc.
Symbols Used in this Manual
Indicates hazards likely to cause harm to
the unit itself or other material damage.
Note:
Indicates special notes and operating
features.
Tip:
Indicates tips and hints for making the
task easier.
A section whose title has one of the following
symbols is applicable only to the disc represented
by the symbol.
DVD
DVD
VCD
Video CDs
CD
Audio CDs
JPEG
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of
heat and never leave it in a parked car exposed to
direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the
disc from the center out.
JPEG Discs
Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or
anti-static spray intended for older vinyl records.
5
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✺
Types of Playable Discs
DVD
(8 cm / 12 cm disc)
Video CD (VCD)
(8 cm / 12 cm disc)
Audio CD
(8 cm / 12 cm disc)
In addition, this unit plays DVD-R, DVD+R, DVDRW, DVD+RW, and CD-R / CD-RW that contains
audio titles, and/or JPEG files.
Notes:
•
Depending on the conditions of the recording
equipment or the CD-R/RW (or DVD -R, DVD
+R, DVD -RW, DVD +RW) disc itself, some
CD-R/RW (or DVD -R, DVD +R, DVD -RW,
DVD +RW) discs cannot be played on the unit.
•
DVD-RW disc can only be played if it was
recorded in VIDEO mode and finalized.
•
Do not attach any seal or label to either side
(the labelled side or the recorded side) of a
disc.
•
Do not use irregularly shaped CDs (e.g.,
heart-shaped or octagonal) since they may
result in malfunctions.
Notes on DVDs and Video CDs
Some playback operations of DVDs and Video
CDs may be intentionally programmed by software manufacturers. This unit plays DVDs and
Video CDs according to disc content designed by
the software manufacturer, therefore some playback features may not be available or other functions may be added.
6
Disc-related terms
JPEG
Joint Pictures Expert Group. JPEG is a compressed file format that allows you to save images
with no limit on the number of colors.
Title (DVD only)
A title is generally a distinct section of a DVD disc.
For example the main feature could be title 1, a
documentary describing how the film was made
could be title 2, and cast interviews could be title
3. Each title is assigned a reference number
enabling you to locate it easily.
Chapter (DVD only)
A chapter is a segment of a title such as a scene
in a film or one interview in a series. Each chapter
is assigned a chapter number, enabling you to
locate the chapter you want. Depending on the
disc, chapters may not be recorded.
Track
A distinct element of audio/visual information,
such as the picture or sound track for a specific
language (DVD), or a musical piece on a video or
audio CD. Each track is assigned a track number,
enabling you to locate the track you want. DVD
discs allow one track of video (with multiple
angles) and several tracks of audio.
Types of Video CDs
There are two types of Video CDs:
•
Video CDs equipped with PBC (Version 2.0)
PBC (playback control) functions allow you to
interact with the system via menus, search
functions, or other typical computer-like operations. Moreover, still pictures of high resolution
can be played if they are included in the disc.
•
Video CDs not equipped with PBC
(Version 1.1)
Operated in the same way as Audio CDs,
these discs allow playback of video pictures as
well as sound, but they are not equipped with
PBC.
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✻
About the Remote Control
This DVD+VCR is designed
and manufactured for playback
of region “1” encoded DVD
software. This unit can play
only DVD discs labeled “1” or “ALL”.
1
ALL
Notes on Regional Codes
•
•
Most DVD discs have a globe with one or
more numbers in it clearly visible on the cover.
This number must match your DVD+VCR’s
regional code or the disc cannot play.
Operation Range
Point the Remote Control at the remote sensor
and press the buttons.
Distance: About 23 ft (7 m) from the front of the
remote sensor.
Angle:
About 30° in each direction of the front of
the remote sensor.
Battery installation
Detach the battery cover on the rear
of the Remote Control, and insert
two (R03/AAA) size batteries with 3
and # aligned correctly.
If you try to play a DVD with a different region
code from your player, the message “Check
Regional Code” appears on the TV screen.
Do not mix old and new batteries and
never mix different types of batteries such
as standard, alkaline, etc.
Notes on Copyrights:
It is forbidden by law to copy, broadcast, show,
broadcast via cable, play in public, or rent copyrighted material without permission.
This product features the copy protection function
developed by Macrovision. Copy protection signals are recorded on some discs. When recording
and playing the pictures of these discs picture
noise will appear. This product incorporates copyright protection technology that is protected by
method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision
Corporation and other rights owners. Use of this
copyright protection technology must be authorized by Macrovision Corporation, and is intended
for home and other limited viewing uses only
unless otherwise authorized by Macrovision
Corporation. Reverse engineering or disassembly
is prohibited.
Notice for Progressive Scan Use
CONSUMERS SHOULD NOTE THAT NOT ALL
HIGH DEFINITION TELEVISION SETS ARE
FULLY COMPATIBLE WITH THIS PRODUCT
AND MAY CAUSE ARTIFACTS TO BE DISPLAYED IN THE PICTURE. IN CASE OF 525
PROGRESSIVE SCAN PICTURE PROBLEMS,
IT IS RECOMMENDED THAT THE USER
SWITCH THE CONNECTION TO THE ‘STANDARD DEFINITION’ OUTPUT. IF THERE ARE
QUESTIONS REGARDING OUR TV SET COMPATIBILITY WITH THIS MODEL 525p
DVD+VCR, PLEASE CONTACT OUR CUSTOMER SERVICE CENTER.
Introduction
Regional Code
Selecting the Viewing Source
You must select one of your output sources (DVD
or VCR) to view on the TV screen.
•
•
If you want to view DVD deck output source:
Press DVD until DVD indicator in the display
window lights and output source of DVD deck
is viewed on the TV screen.
If you want to view VCR deck output source:
Press VCR until VCR indicator in the display
window lights and output source of VCR deck
is viewed on the TV screen.
Notes:
•
•
•
If you insert a disc while the DVD+VCR is in the
VCR mode, the DVD+VCR will switch to DVD mode
automatically.
If you insert a cassette tape without prevention tab
while the DVD+VCR is in the DVD mode, the
DVD+VCR will switch to VCR mode automatically.
To selecting and viewing the E to E sources (tuner,
line1, line2), the unit must be in VCR mode.
Manufactured under license from Dolby
Laboratories. “Dolby” and the double-D
symbol are trademarks of Dolby Laboratories.
DTS and DTS Digital Out are trademarks
of Digital Theater Systems, Inc.
This model is equipped with SQPB (S-VHS
QUASI PLAYBACK) that makes it possible
to play back S-VHS recordings with regular VHS resolution.
7
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✼
Front Panel
a
b
Disc Tray (DVD deck)
Insert a disc here.
Indicates when the Progressive scan is
active.
Cassette Compartment (VCR deck)
Indicates repeat mode.
[P]
Insert a video cassette here.
c
d
Switches the DVD+VCR ON and OFF.
DVD+VCR is in timer recording or a
timer recording is programmed (VCR
part only).
m)
REW (m
A cassette is in the VCR deck.
POWER 1/:
- DVD: Skip to beginning of current chapter or
track, press twice in quick successions to go to
previous chapter or track. Press and hold button
for about two seconds to search backward.
- VCR: Rewinds the tape during the stop mode or
for fast reverse picture search.
e
VCR
REC
PM
TV
The VCR deck is selected.
DVD+VCR is Recording.(VCR part only)
Indicates PM time. (AM is not diplayed.)
Lights when TV mode is active.
N)
PLAY (N
Indicates total playing time,
elapsed time, remaining time
or current deck status
(Playback, Pause, etc).
Starts playback of a disc or tape.
f
M)
FF (M
- DVD: Skip to next chapter or track. Press and
hold for two seconds for a fast forward search.
- VCR: Advances the tape during the STOP mode
or for fast forward picture search.
g
i
l
m
n
Z)
OPEN/CLOSE (Z
Display Windows
CH -/+
To scan up or down through memorized channels.
z)
REC (z
To record normally or to activate One-touch Timer
Recording by repeated presses.
Opens or closes the disc tray.
j
Z)
EJECT (Z
Ejects the tape in the VCR deck.
X)
PAUSE (X
Pause playback or recording. Press repeatedly for
frame-by-frame playback.
Remote Sensor
Point the DVD+VCR Remote Control here.
x)
STOP (x
Stops playback of the disc or tape.
h
k
o
VCR/DVD (output select)
Select one of your output sources to view on the
TV screen between DVD and VCR.
p
DVD
The DVD deck is selected.
A disc is in the DVD deck.
(Lights when a disc is in the DVD deck
and Flashes when no disc.)
8
LINE2 (VIDEO/AUDIO (L/R) input)
Connect to the audio/video output of an external
source (Audio system, TV/Monitor, Another VCR).
✽
Remote Control
DISPLAY
Accesses On-Screen Display.
Switches between the clock, tape counter
and tape remaining modes on the display.
Introduction
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
DVD Select the DVD+VCR function mode to DVD.
EJECT (Z) Ejects the tape in the VCR deck.
ENTER / OK Confirms menu selections. Displays
functions on the TV screen.
MARKER Marks any point during playback.
OPEN/CLOSE (Z) Opens and closes the disc tray.
PAUSE (X) Pause playback or recording.
Press repeatedly for frame-by-frame
playback.
PLAY (N) Starts playback.
POWER (1/:) Switches DVD+VCR ON and OFF.
PROGRAM Shows or hides the menu for Program
playback of Audio CD.
RANDOM Plays tracks in random order.
z) Starts recording. Press repeatedly to set the
REC (z
recording time.
REPEAT Repeats chapter, track, title or all.
REPEAT A-B Repeats sequence between two points
(A and B).
O) Removes the setup menu.
RETURN (O
REW (m) / FF (M)
- DVD: Search backward or forward.
- VCR: Rewinds/Advances the tape during the STOP
mode, for fast backward/forward picture search.
SEARCH Displays Marker Search menu.
SETUP MENU Accesses or removes DVD Setup
menu and VCR menu.
SKIP (. / >) Go to next chapter or track.
Returns to beginning of current
chapter or track or go to previous
chapter or track.
0-9 Selects numbered options in a menu.
b B v V Selects menu options.
Fast forwards picture search through 30 seconds of
recording.
AUX Selects the VCR deck’s source
(Tuner, LINE 1, or LINE 2).
A.MONITOR Selects an audio language (DVD) or an
SPEED Selects recording speed.
x) Stops playback or recording.
STOP (x
SUBTITLE Selects a subtitle language.
TITLE Displays the disc’s Title menu, if available.
TV/VCR
audio channel (VCD).
To view channels selected by the VCR tuner
or by the TV tuner.
ANGLE Selects a DVD camera angle, if available.
VCR Select the DVD+VCR function mode to VCR.
CH -/+ Selects VCR channels. Adjusts manually the
ZOOM Enlarges DVD video image.
tape’s picture on the TV screen.
CLEAR (0000) Removes a mark on the Marker
Search menu.
DISC MENU Accesses menu on a DVD disc.
Note:
The Remote Control of a JVC TV or Receiver will not
operate the unit.
9
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✴
Rear Panel
a
a
bcde
g
h
ANT.IN
f
e
Connect the VHF/UHF/CATV antenna to this terminal.
b
c
f
Connect the audio/video output of an external
source (Audio system, TV/Monitor, VCR,
Camcorder).
g
Connect to a TV with video and audio inputs.
d
Connect to a TV or other equipment with audio
inputs.
VCR IN LINE 1 (VIDEO/AUDIO
(Left/Right))
DVD/VCR OUT (VIDEO/AUDIO
(Left/Right))
AUDIO OUT (Left/Right) (DVD OUT)
AC Power Cord
Plug into the power source.
RF. OUT
Connect to a TV with RF coaxial inputs.
h
COAXIAL (DIGITAL AUDIO OUT jack)
(DVD OUT)
Connect to digital (coaxial) audio equipment.
COMPONENT/PROGRESSIVE SCAN
VIDEO OUT (Y Pb Pr) (DVD OUT)
Connect to a TV with Y Pb Pr inputs.
Preparation
Depending on your TV and other equipment there are various ways you can connect
the player. Please refer to the manuals of your TV, VCR, stereo system or other devices
as necessary for additional connection information.
Notes:
10
•
The picture and sound of a nearby TV, VCR, or radio may be distorted during playback. Position the units away
from each other or turn off the unit after removing the disc.
•
Make sure the DVD+VCR is connected directly to the TV and tune the TV to the correct video input channel.
•
Do not connect the DVD+VCR’s AUDIO OUT jack to the phone in jack (record deck) of your audio system.
Do not connect the DVD+VCR via another VCR. The DVD image could be distorted by the copy protection
system.
✵✵
Connecting an Antenna
or Cable TV
a Antenna:
Disconnect the antenna from the rear of the TV
and identify the antenna cable. If it is a round 75
ohm coaxial cable connect it directly to the jack
marked ANT.IN on your DVD+VCR. If your antenna cable is flat connect it to a 300-ohm to 75-ohm
antenna adaptor (not supplied) and slip the adaptor over the ANT.IN jack. Don’t attempt to screw it
into to the DVD+VCR.
b Cable TV:
If your cable connection has no converter or
descrambler, unscrew the cable from your TV and
attach it to the ANT.IN jack on the DVD+VCR. If a
converter is required connect a coaxial cable from
the wall jack to the IN connector on the converter,
and a coaxial cable from the OUT connector on
the converter to the ANT IN on your DVD+VCR.
This cable hookup permits both TV and
DVD+VCR operation.
To view or record a CATV channel when
using cable box
1. Tune the TV to the DVD+VCR output channel
(CH 3 or 4).
2. Set the DVD+VCR channel selector to the
cable output channel. (Example: CH3)
3. Select a channel using the cable converter.
Notes:
•
With this connection, you cannot record one program while viewing another.
•
If you are using a cable box to tune channels, it is
not necessary to do Auto Channel Set.
Preparation
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
Basic TV Connections
Make one of the following connections, depending
on the capabilities of your TV.
Antenna
Antenna
Rear of TV
ANTENNA
INPUT
VIDEO
INPUT
AUDIO INPUT
L
OR
OR
R
V
R
A1
Rear of DVD+VCR
Rear of DVD+VCR
C
Pr
A2
Pb
Y
COMPONENT/PROGRESSIVE SCAN
VIDEO INPUT
R
L
AUDIO INPUT
Rear of TV
11
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✶
RF coaxial connection
Connect the RF.OUT jack on the DVD+VCR to
the antenna in jack on the TV using the supplied
75-ohm Coaxial Cable (R).
How to set the DVD+VCR’s RF output
channel
1. When the DVD+VCR is turned off, press and
hold both CH - and CH + on the front panel for
more than five seconds. “RF03” or “RF04”
appears in the display window.
2. Press either CH - or CH + to change the RF
output channel (RF03 or RF04). Tune the TV
to this channel.
3. Turn off the DVD+VCR.
Audio/Video connection
1. Connect the DVD/VCR VIDEO OUT jack on
the DVD+VCR to the video in jack on the TV
using an optional video cable (V).
2. Connect the Left and Right DVD/VCR AUDIO
OUT jacks on the DVD+VCR to the audio
left/right in jacks on the TV (A1) using an
optional audio cables.
Note:
Optional TV Connections
These connections support only DVD playback.
The tuner and VCR still output through the
RF.OUT (R) or DVD/VCR OUT (A, V) jacks.
Component Video / Progressive Scan
connection
If your television is a high-definition or “digital
ready” television, you may take advantage of the
DVD+VCR’s progressive scan output for the highest video resolution possible.
1. Connect the COMPONENT/PROGRESSIVE
SCAN VIDEO OUT jacks on the DVD+VCR to
the corresponding in jacks on the TV using an
optional Y Pb Pr cable (C).
2. Connect the Left and Right AUDIO OUT jacks
of the DVD+VCR to the audio left/right in jacks
on the TV (A2) using an optional audio cables.
Notes:
•
When you use Composite Video signal, set the
Progressive Scan to “Off” on the setup menu.
•
Progressive scan does not work with the Composite
video connections (yellow VIDEO OUT jack).
•
If your TV does not accept the Progressive Scan format, the picture will appear scrambled. Switch to
composite video output.
If you use this connection, set the TV’s source selector
to VIDEO.
Audio Connection for DVD
You can listen to playback using DVD/VCR
AUDIO OUT (A1), AUDIO OUT (A2), COAXIAL
(X) and RF. OUT (R) connections. COAXIAL (X)
and AUDIO OUT (A2) is used only for listening to
DVD playback. (See page 11.)
Connecting to an amplifier equipped with two
channel analog stereo
Connect the Left and Right AUDIO OUT (or
DVD/VCR AUDIO OUT) jacks on the DVD+VCR
to the audio left and right in jacks on your amplifier, receiver, or stereo system using an optional
audio cables (A1, A2).
12
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✷
Connecting to an amplifier equipped with two
channel digital stereo (PCM) or to an
Audio/Video receiver equipped with a multichannel decoder (Dolby Digital™, MPEG 2, or
DTS)
1. Connect the DVD+VCR’s DIGITAL AUDIO
OUT jacks (COAXIAL X) to the corresponding
in jack on your amplifier. Use a digital (COAXIAL X) audio cable.
Connecting External Audio/Video (A/V)
source to DVD+VCR
Connect the VCR IN LINE 1 or LINE 2 jacks on
the DVD+VCR to the audio/video out jacks on
your accessory component, using the optional
audio/video cables. (Refer to page 24 for
“Recording from External Components”.)
2. You will need to activate the DVD+VCR’s digital output. (See “AUDIO” on page 18).
Jack panel of external source
Digital Multi-channel sound
Preparation
A digital multi-channel connection provides the best
sound quality. For this you need a multi-channel
Audio/Video receiver that supports one or more of
the audio formats supported by your DVD+VCR
(MPEG 2, Dolby Digital and DTS). Check the
receiver manual and the logos on the front of the
receiver.
Caution:
This DVD+VCR is not equipped with DTS decoder,
but DTS will be output through Digital coaxial out
when DTS audio stream is selected in DVD disc
soundtrack menu.
Notes:
•
If the audio format of the digital output does not match
the capabilities of your receiver, the receiver will produce a strong, distorted sound or no sound at all.
•
Six Channel Digital Surround Sound via digital connection can only be obtained if your receiver is
equipped with a Digital Multi-channel decoder.
•
To see the audio format of the current DVD in the
on-screen display, press A.MONITOR.
Rear of DVD+VCR
A1
A2
L
R
AUDIO INPUT
X
COAXIAL
DIGITAL INPUT
Amplifier (Receiver)
13
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✸
Initial Settings - VCR
• AUTO CLOCK SET
The Auto Clock Set feature is set to ON at the
factory. In the ON setting, the DVD+VCR looks
for a channel carrying XDS (Extended Data
Services) information. XDS updates the clock
using the Coordinated Universal Time.
- Use b / B to choose ON or OFF.
By using the VCR Setup menu, you can make
various adjustments to items such as clock setting, and timer recordings.
Your DVD+VCR allows Remote Control adjustment of several features.
• DAYLIGHT SAVINGS
You can turn Daylight Savings On or Off manually. If you choose “AUTO”, the DVD+VCR sets
the clock using the DST information broadcast
in the signal (channel).
- Use b / B to choose AUTO, ON or OFF.
General Operation
1. Press VCR on the Remote Control.
2. Press SETUP MENU and the MAIN menu will
appear.
• TIME ZONE
You can set your local Time Zone manually. If
you choose “AUTO”, the DVD+VCR sets the
clock using the first Coordinated Universal Time
information it finds in a broadcast signal.
- Use b / B to choose the correct time zone
(AUTO, EASTERN, CENTRAL, MOUNTAIN,
PACIFIC, ALASKA or HAWAII).
Notes:
3. Use v / V to select the desired menu, then
press ENTER / OK.
4. Use v / V to choose a desired option on the
selected Menu. Then use b / B to choose a
desired setting.
•
•
The Auto Clock feature enables the DVD+VCR to
set up the clock while the DVD+VCR is turned off.
There are cases where the TV station does not send
or sends wrong date and/or time information and the
DVD+VCR sets the incorrect time. If this happens
we recommend that you set the clock manually.
5. Press SETUP MENU when finished.
Note:
Menus remain on-screen for 3 minutes.
CLOCK
The DVD+VCR gives you two ways to set the time
and date: the Auto Clock Feature or Manually.
Auto Clock Set
Manual Clock Set
Use v / V / b / B to enter the necessary information.
• MONTH : Choose the month.
• DAY : Choose the date.
The day of the week will display automatically.
• YEAR : Choose the year.
• TIME : Choose the time.
Press and hold b / B to advance clock continuously.
Notes:
•
If setting the clock manually, “AUTO CLOCK SET”
must set to “OFF”. If it is left set to “ON,” it will override the manual setting after the unit is turned off.
•
The clock uses the 12-hour system. Be sure to set
AM and PM correctly.
PROGRAM
The Timer Recording function allows you to record
up to 8 programs within a period of one year. (See
pages 23-24).
14
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✹
TUNING
SETUP
This DVD+VCR is equipped with a frequency
synthesized tuner capable of receiving up to 181
channels. These include VHF channels 2-13, UHF
channels 14-69 and CATV channels 1-125.
Auto Channel Programming
FUNCTION OSD
Preparation
The on-screen display can be turned on or off.
AUDIO MODE
1. Choose the SOURCE SELECT option, then
use b / B to select TUNER.
Use b / B to switch among TUNER, LINE1, and
LINE2.
2. Choose the AUTO CHANNEL SET option,
then use b / B to find channels.
• The tuner will automatically cycle through all
available channels (TV/CATV) in the area and
place them in the tuner’s memory.
• After the AUTO CHANNEL SET is complete, the
TUNING menu will hide and return to the TV
screen automatically.
• If the power fails or the DVD+VCR is unplugged
the channel settings are kept in memory for only 3
seconds.
3. Make sure the TUNING BAND is set appropriately (TV or CATV).
• TV : If you are using a standard antenna to
receive channels.
• CATV : If you are using basic cable to receive
channels.
The DVD+VCR has two separate audio playback
systems, the high quality VHS Hi-Fi system and
standard NORMAL mono system. The same
audio is generally recorded on both systems. The
VHS Hi-Fi system plays on separate (left and
right) channels, and the NORMAL system plays
monaural sound. The normal track is always
played so the cassette can be played on a
DVD+VCR that does not have VHS Hi-Fi.
BROADCAST TYPE (STEREO / SAP / MONO)
Multichannel Television Sound (MTS) carries
stereo and/or Second Audio Program (SAP) bilingual signals. Set this display to the desired position when both MTS stereo and SAP signals are
received. When only one of the MTS signal is
received, the DVD+VCR automatically selects the
corresponding receiving mode (Stereo or SAP)
regardless of the selected position. For normal
operation, the display should be in the STEREO
position. The DVD+VCR will then record a
STEREO program when available, and record a
mono program IF the program is NOT IN
STEREO. For weak STEREO and/or SAP broadcasts, changing the display to mono may give
clearer sound.
AUDIO OUTPUT (STEREO / LEFT / RIGHT)
To Add or Erase Channels
This feature allows you to add or erase channels
from memory manually.
1. Choose the CH. ADD/DEL option, then use b
/ B to select a channel to add or erase.
2. Use ENTER / OK to add or erase the channel.
Repeat steps 1 and 2 to add or erase other
channels.
3. Press SETUP MENU to return to the TV
screen.
Used during playback [when AUDIO MODE (HI-FI/
NORMAL) is in HI-FI position] for selecting the
audio output signals from the AUDIO OUT terminals (L ch and R ch), and RF.OUT. This display
setting should normally be left in the stereo position, so that when a stereo tape is played, the
stereo sound will be heard through the left and right
channels. If a mono tape is played and the audio
output is set to stereo, the same mono sound will
be heard from both left and right channels.
In addition to the above settings, these other
sources are also affected:
1. Playback of CD, DVD or VCD
2. Output of built in tuner, Line 1 or Line 2
15
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✺
Initial Settings - DVD
By using the DVD Setup menu, you can make
various adjustments to items such as picture and
sound. You can also set a language for the subtitles and the Setup menu, among other things. For
details on each Setup menu item, see pages 16 to
19.
To display and exit the Menu:
Press SETUP MENU to display the menu. A second press of SETUP MENU will take you back to
initial screen.
To go to the next level:
Press B on the Remote Control.
To go back to the previous level:
Press b on the Remote Control.
General Operation
1. Press DVD on the Remote Control.
2. Press SETUP MENU.
The Setup menu appears.
3. Use v / V to select the desired option then
press B to move to the second level. The
screen shows the current setting for the
selected item, as well as alternate setting(s).
4. Use v / V to select the second desired option
then press B to move to the third level.
5. Use v / V to select the desired setting then
press ENTER / OK to confirm your selection.
Some items require additional steps.
6. Press SETUP MENU or PLAY (N) to exit the
Setup menu.
16
LANGUAGE
LANGUAGE
Menu Language
English
Disc Audio
Original
Disc Subtitle
Original
Disc Menu
Original
Move
Select
Menu Language
Select a language for the VCR and DVD’s setup
menu and information display.
Disc Audio / Subtitle / Menu
DVD
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
Original: Refers to the original language in which
the disc was recorded.
Other: To select another language, press number
buttons then ENTER / OK to enter the corresponding 4-digit number according to the language
code list in the reference chapter (see p. 35). If
you enter the wrong language code, press
CLEAR (0000).
Off (for Disc Subtitle): Turn off Subtitle.
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✻
4. When the confirm menu appears on your
screen “Cancel” is highlighted as default. Use
the b button to highlight “Enter”.
DISPLAY
DISPLAY
TV Aspect
4 : 3
Display Mode
Letterbox
Progressive Scan
Off
Move
5. Pressing ENTER ✳ O❏ will set this unit to progressive scan mode.
DVD
4:3 :
Select when a standard 4:3 TV is connected.
16:9 :
Select when a 16:9 wide TV is connected.
Display Mode
Notes:
•
If you set Progressive Scan to ON in error, you must
reset the DVD+VCR. Press STOP (x) and hold it for
more than five seconds before releasing it. The
video output will be restored to the standard setting,
and a picture will once again be visible on a conventional analog TV or monitor.
•
Do not turn off this DVD+VCR while the “PROGRESSIVE SCAN MODE” message is displayed in the TV
screen.
DVD
Display Mode setting works only when the TV
Aspect mode is set to “4:3”.
Letterbox: Displays a wide picture with bands on
the upper and lower portions of the screen.
Preparation
TV Aspect
Select
Panscan: Automatically displays the wide picture
on the entire screen and cuts off the portions that do
not fit.
Progressive Scan
DVD
Progressive Scan Video provides the highest
quality pictures with less flickering.
If you are using the Component Video jacks for
connection to a TV or monitor that is compatible
with a progressive scan signal, set Progressive
Scan to On.
To turn on progressive scan:
Connect component/progressive out of this unit to
the input of your monitor/television, set your television or monitor to component/progressive Input.
1. Select “Progressive Scan” on the DISPLAY
menu then press B.
2. Select “On” using the v / V buttons.
3. Press ENTER / OK to confirm your selection.
The confirm menu will appear.
17
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✼
AUDIO
DRC (Dynamic Range Control)
Each DVD disc has a variety of audio output
options. Set this unit’s AUDIO options according
to the type of audio system you use.
With the DVD format, you can hear a program’s
soundtrack in the most accurate and realistic
presentation possible, thanks to digital audio technology. However, you may wish to compress the
dynamic range of the audio output (the difference
between the loudest sounds and the quietest
ones). This allows you to listen to a movie at a
lower volume without losing clarity of sound. Set
DRC to On for this effect.
AUDIO
Dolby Digital
Bitstream
DTS
Bitstream
MPEG
PCM
Sample Freq.
48 kHz
DRC
On
Move
Dolby Digital / DTS / MPEG
Select
DVD
Bitstream: Select “Bitstream” if you connect
the DVD+VCR’s DIGITAL AUDIO OUT jack to
an amplifier or other equipment with a Dolby
Digital, DTS or MPEG decoder.
PCM (for Dolby Digital / MPEG): Select
when connected to a two-channel digital
stereo amplifier. DVDs encoded in Dolby
Digital or MPEG will be automatically downmixed to two-channel PCM audio.
Off (for DTS): If you select “Off”, the DTS signal is not output through the DIGITAL AUDIO
OUT jack.
Sample Freq. (Frequency)
DVD
If your receiver or amplifier is NOT capable of
handling 96 kHz signals, select 48 kHz. When this
choice is made, this unit automatically converts
any 96 kHz signals to 48 kHz so your system can
decode them.
If your receiver or amplifier is capable of handling
96 kHz signals, select 96 kHz. When this choice is
made, this unit passes each type of signal through
without any further processing.
Check the documentation for your amplifier to verify its capabilities.
18
DVD
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✵✽
OTHERS
B.L.E. (Black Level Expansion)
The Auto Play, and B.L.E. settings can be
changed.
To select the black level of playback pictures.
Set your preference and monitor’s ability.
On: Expanded grey scale. (0 IRE cut off)
OTHERS
Off: Standard grey scale. (7.5 IRE cut off)
On
Auto Play
On
B.L.E.
Off
Move
PBC
Select
Preparation
PBC
VCD
Set Playback Control (PBC) to On or Off.
On: Video CDs with PBC are played according to
the PBC.
Off: Video CDs with PBC are played the same
way as Audio CDs.
Auto Play
DVD
You can set up the DVD+VCR so a DVD disc
automatically starts playing whenever the DVD is
inserted.
If Auto Play mode is set to On, this DVD player
will search for title that has the longest playback
time and then play back the title automatically.
On: Auto Play function is active.
Off: Auto Play function is not active.
Note:
The Auto Play function may not work for some DVDs.
19
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✴
Operation
This chapter describes how to operate the VCR
and DVD.
VCR Tape Playback
Press the VCR button to select the device to be
operated.
Manual Tracking
To manually adjust the tracking use the CH -/+
buttons during playback.
Notes:
•
Vertical jitter requires a very fine adjustment.
•
Tracking is automatically reset to normal when the
tape is ejected or the power cord is unplugged for
more than 3 seconds.
Basic Instructions
1. Turn on the TV.
2. Tune the TV to the DVD+VCR output channel
(CH 3 or 4) or if a direct VIDEO/AUDIO
connection is made between the DVD+VCR
and the TV, set the TV’s source selector to
VIDEO.
3. Insert a pre-recorded video cassette.
The
indicator lights and the DVD+VCR
powers on automatically.
4. If the
(TIMER) indicator in the display window is lit press POWER 1/: once.
5. If a tape without a safety tab is inserted the
unit starts playback automatically.
If not, press PLAY (N).
6. Press STOP (x) to stop playback. If the tape
reaches the end before you press STOP (x)
the DVD+VCR automatically stops, rewinds
and ejects the tape.
Search
This function lets you visually search for a tape
section in either direction: forward and reverse.
During the high-speed picture search modes, the
audio is muted and horizontal lines (noise bars)
appear. Also, a short time is needed to stabilize
the tape speed when re-entering the PLAY mode
so slight interference may be observed during this
time.
To search:
1. Press REW (m) or FF (M) during playback.
2. To return to playback, press PLAY (N).
Notes:
•
After 3 minutes in SEARCH mode the DVD+VCR
returns to PLAY mode to protect the tape and video
heads.
•
During the tape fast rewinding (backward or forward), don’t press the same button (REW or FF)
again. Otherwise it takes more time to rewind the
tape.
Notes:
•
It is not necessary to select the tape speed for playback because it is automatically selected by the
DVD+VCR.
Also, during playback the TV/VCR selector switches
to VCR mode automatically.
•
When playing back tapes that have been overrecorded with new content, the original audio may
be audible during auto tracking.
Auto Tracking
Automatic tracking adjusts the picture to remove
snow or streaks when:
•
•
•
A tape is played for the first time.
The tape speed (SP, LP, SLP) changes.
Streaks or snow appear due to scratches on
the tape.
Still Picture and Frame-by-Frame
Playback
1. Press PAUSE (X) during playback.
A still picture appears on the TV screen and
the audio is muted.
2. If the still picture vibrates vertically, stabilize it
by using CH -/+ on the Remote Control.
3. Press PAUSE (X) repeatedly to advance the
video picture one frame at a time.
4. To return to playback, press PLAY (N).
Note:
After 5 minutes in STILL mode the DVD+VCR stops to
protect the tape and video heads.
20
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✵
Slow Motion
1. While in still mode, press FF (M). The tape
is played at a speed 1/19 times slower than
the normal speed.
2. Use CH -/+ on the Remote Control if necessary to adjust the tracking.
3. To return to the normal speed, press PLAY
(N).
Notes:
•
During slow motion, audio is muted and horizontal
lines (noise bars) may appear on the TV screen. This
is normal.
After 3 minutes in SLOW MOTION mode the
DVD+VCR goes back to PLAY mode to protect the
tape and video heads.
CM SKIP (Commercial Skip)
This feature is useful for skipping commercials or
short program segments.
1. Press
in playback mode.
The DVD+VCR performs a fast forward picture
search through 30 seconds of recording.
2. Press
again to extend the search time by
an addition 30 seconds. The maximum search
time is 3 minutes.
3. When the search is complete, the DVD+VCR
goes into playback mode automatically.
VHS Hi-Fi Stereo / MTS
Broadcast
This DVD+VCR is equipped with the VHS Hi-Fi
audio sound system for recording and playback.
The information below gives a brief description of
Hi-Fi audio and how to record and play a tape in
the Hi-Fi audio mode.
Hi-Fi Stereo Audio Sound
A stereo TV with AUDIO/VIDEO input jacks or a
stereo audio system is required for true stereo
playback. To experience the full and rich stereo
sound available with Hi-Fi recorded tapes, we recommend the connection of this unit to a home
stereo audio system.
1. Set the AUDIO MODE option to HI-FI on the
VCR SETUP menu.
The other options are (LEFT) POSITION,
which results in the left channel sound (L)
being heard from both speakers or (RIGHT)
POSITION, which results in the right channel
sound (R) being heard from both speakers.
3. Insert a cassette and press PLAY (N).
Note:
If playing back a HI-FI tape produces noisy audio, manually change the menu setting from HI-FI to NORMAL.
Operation
•
2. Set the AUDIO OUTPUT option to STEREO
so that the left channel sound (L) is heard from
the left speaker and the right channel sound
(R) is heard from the right speaker.
MTS (Multi-Channel TV Sound)
This DVD+VCR can decode MTS stereo and bilingual (SAP) off-the-air broadcast sound signals. It
also decodes stereo TV sound from local cable
companies as long as they operate on assigned
cable frequencies and use the EIA-recommended
MTS stereo/bilingual TV sound system.
Multichannel TV Sound Indicator (MTS)
When you press ENTER / OK one or both of the
indicators appears on the TV Screen.
STEREO
The DVD+VCR can record in stereo onto the VHS
Hi-Fi audio tracks when the BROADCAST TYPE
option is in the STEREO position. The DVD+VCR
can also record mono audio onto the mono audio
track.
SAP
Some stations transmit a Second Audio Program,
which is used for a second language or additional
information.
STEREO/SAP
Use the BROADCAST TYPE option to select the
desired recording mode (STEREO or SAP).
21
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✶
VCR Tape Recording
Basic Instructions
1. Turn on the DVD+VCR and TV.
2. Tune the TV to the DVD+VCR output channel
(CH 3 or 4) or if a direct VIDEO/AUDIO connection is made between the DVD+VCR and
the TV, set the TV’s source selector to VIDEO.
3. Insert a video cassette with the safety tab
intact.
4. Select the desired channel using CH -/+.
5. If you are recording from another source via
audio/video input jacks (at the rear or front
panel), select LINE1 or LINE2 using AUX, CH
+ or CH -.
6. Set the desired recording speed (SP or SLP)
by pressing SPEED. This DVD+VCR is not
designed to record in LP mode.
7. Set the MTS mode (STEREO or SAP). Set the
BROADCAST TYPE option to SAP if applicable.
8. Press REC (z) and recording starts. The REC
indicator appears in the display window. If a
cassette with no safety tab is loaded, the cassette is ejected.
x) to stop recording. If the tape
9. Press STOP (x
x) is pressed,
reaches the end before STOP (x
the DVD+VCR stops, rewinds and ejects the
tape.
Tip:
Use PAUSE (X) for best results when making changes
while recording. For example, if you want to change
channels while recording, first press PAUSE (X) to put
the unit in pause mode, select the desired channel on
the DVD+VCR, and then press PAUSE (X) again to
resume recording.
To record one TV program while watching
another
1. Press TV/VCR to select the TV mode during
recording. The TV indicator appears.
2. Using the TV, select the channel to be viewed.
Timer Recording
For unattended recording, you must input the
channels to be recorded and the starting and ending times.
Things to know before starting
If you try to set the program timer before setting the clock, “PLEASE SET THE CLOCK”
appears for a moment and then CLOCK
menu appears on the TV screen. Set the time
and date before proceeding.
1. Turn on the DVD+VCR and the TV.
2. Be sure the TV is set to the DVD+VCR output
channel (3 or 4).
3. Make sure the TUNING BAND in the TUNING
menu is set appropriately (TV or CATV).
4. Press SETUP MENU and the MAIN menu
appears.
5. Use v / V to choose the PROGRAM menu
and press ENTER / OK.
Note:
During the VCR recording mode, you cannot change to
the DVD mode.
To pause the recording
1. Press PAUSE (X) to pause the tape during
recording. The REC indicator flashes in the
display window.
2. When you want to continue recording, press
PAUSE (X) or press REC (z).
After 5 minutes in PAUSE mode, the
DVD+VCR stops automatically to protect the
tape and the video heads.
22
If eight programs are already entered, the
FULLY PROGRAMMED message appears for
a moment and then PROGRAM 1 appears on
the TV screen.
6. Use the v / V buttons to switch between the
program options, and the b / B buttons to
input the program information:
Input the month, day, start and stop times of
the program you want to record.
✶✷
Channel: Select a TV channel, LINE1 or
LINE2. If you have CABLE TV and use a cable
box (converter) you must set the channel to
match the cable box output channel (usually
CH 3 or 4). Change channels on the cable box
instead of with the DVD+VCR. If you use a
cable converter, you can program multiple
recordings only on the converter box output
channel. This is because the converter determines what channel you view through your
DVD+VCR.
Speed: AUTO mode determines how much
tape is left and switches the speed from SP to
SLP if it is necessary to complete recording
the program.
If this occurs there could be some picture and
sound distortion at the point where the speed
changes.
Repeat: To record up to 8 programs on a certain day of every week select WEEKLY. To
record up to 8 programs at the same time
Monday through Friday select DAILY.
Otherwise select ONCE.
7. Press SETUP MENU and the program is
memorized by the DVD+VCR.
8. Additional programs may be entered by
repeating steps 1-7.
9. Ensure you insert a tape with the record safety
tab intact before the first programmed time.
Checking or Erasing the Timer Program
Programming can be checked whenever the
DVD+VCR is turned on.
1. Press SETUP MENU and the MAIN menu
appears.
2. Use v / V to choose the PROGRAM menu
and press ENTER / OK.
3. Use b / B to select a program you want to
check or erase. To erase the program, press
CLEAR (0000).
4. Press SETUP MENU to return to the TV
screen.
Program Priority
If the recording start and end times of preset programs overlap on the same day (see the example), the second program is not recorded until the
first is finished.
Operation
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
10. Press STOP (x) to end timer recording.
Notes:
•
If you make a mistake or want to change a setting,
use v to select the option and correct it using b / B.
•
If the program preset time is past, the “PAST TIME
PROGRAMMED” message appears on the TV
screen. Return to the incorrect program and program it with the correct time.
•
If you enter a past date, the timer recording will be
performed on that date of the next year.
•
If the power fails or the DVD+VCR is unplugged the
clock and timer settings are kept in memory for only
3 seconds. Otherwise you must reset the clock and
timer.
•
If the tape indicator is blinking, no tape is loaded.
•
When you are playing DVD at programmed
Recording time, the DVD+VCR automatically
change to VCR mode and start recording.
•
The DVD+VCR will automatically power off when
Timer Recording ends.
In this example, the first part of program numbers
2 and 3 are not recorded.
23
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✸
Instant Timer Recording
Extending the Recording Time
With this feature you can record for a preset
length without using the program timer.
The recording time can be extended anytime by
pressing REC (z). Subsequent presses result in
advancing the recording time by 30-minute
increments.
1. Turn on DVD+VCR and the TV.
2. Be sure the TV is tuned to the DVD+VCR output channel (CH 3 or 4). If a direct
VIDEO/AUDIO connection is made between
the DVD+VCR and the TV, set the TV’s
source selector to VIDEO.
Note:
If you press PAUSE (X) during instant timer recording,
the instant timer recording is cancelled. It goes to normal recording PAUSE mode.
3. Insert a video cassette with the safety tab
intact.
4. Select the desired channel using CH -/+ or the
number buttons (0-9). The channel number
appears on the TV screen. If you are recording
from another source via audio/video input
jacks (at the rear or front panel), select LINE1
(rear jacks) or LINE2 (front jacks) by using
AUX.
Recording from External
Components
5. Set the desired recording speed (SP or SLP)
using SPEED. The tape speed appears on the
TV screen.
1. Make sure that the component you want to
record from is connected properly to the
DVD+VCR. See page 13.
2. Press AUX repeatedly to select the external
input to record from.
• LINE1 (L1): Audio/Video Input mounted on
back panel.
• LINE2 (L2): Audio/Video Input mounted on
front panel.
3. Load a recordable tape.
4. Set a recording mode (SP or SLP) as necessary by pressing SPEED repeatedly.
5. Play the tape or disc in the external component.
If you have a TV attached to your DVD+VCR,
you can see the video palying.
6. Press REC (z) once to start recording.
The REC indicator lights in the display window.
7. Press STOP (x) to stop recording.
6. Press REC (z) twice. The menu appears on
the TV screen, recording starts, and the
(TIMER) indicator lights.
INSTANT TIMER RECORD
CHANNEL
2
SPEED
SP
START
NOW
LENGTH
0H30M
7. Press REC (z) repeatedly to select the
recording time length. Each time you press
this button the recording time increases 30
minutes (up to 9 hours). At the end of the
recording, the DVD+VCR will stop recording
and shut off.
If you set the time to 0H00M, the DVD+VCR
goes into the normal recording mode. Press
STOP (x) to stop the recording.
You can record from an external component, such
as a camcorder or VCR, connected to any of the
DVD+VCR’s external inputs.
Notes:
•
24
Checking the Recording Time
•
Press REC (z) once to check the recording time.
The recalled setting automatically returns to the
TV screen after 6 seconds.
•
Before recording, confirm the recording start position.
If your source is copy-protected using CopyGuard,
you will not be able to record it using this unit. See
Copyright on page 7 for more details.
To record for a fixed length of time, see Instant
Timer Recording.
✶✹
Copying from DVD to VCR
Each press of ENTER / OK changes the TV
screen in the following sequence.
You can copy the contents of a DVD to a VHS tape.
STOP
SP
1. Insert the disc you wish to copy into the DVD
deck and close the disc tray.
CH 4
STEREO
APR 30 , SAT
2. Insert a blank VHS video tape into the VCR deck.
2:15 PM
0:35:40
3. Find the place on the DVD from which you
want to start dubbing using the PLAY, FF,
REW and PAUSE functions.
For best results, pause playback at the point
from which you want to record.
4. Press REC (z). The DVD goes into PLAY
mode and the VCR goes into RECORD mode.
If the DVD disc menu appears, you may need
to press PLAY (N) manually to begin copying.
REM 1:58
Real-Time Counter
If a tape with contents recorded on it is inserted
into the VCR, the real-time counter shows length
of the tape running in hours, minutes, and seconds. Press DISPLAY to select the real-time
counter display. Every press of DISPLAY
changes the TV screen as illustrated below.
5. When the DVD is finished playing,
press STOP (x) to end copying.
2:15 AM
Notes:
•
•
•
•
•
•
2:15 PM
CLOCK
If the DVD you are attempting to copy is copy protected, you will not be able to copy the disc. It is not
permitted to copy Macrovision encoded DVDs (or
Discs). “Lock” is displayed in the display window.
You must stop the copy process manually when the
DVD movie ends, or the unit may replay and record
over and over again.
When you stop the DVD playback during copying,
the recording on VCR is stopped automatically.
The mark of DVD playback will be recorded at the
beginning of the copied tape.
If you press DISPLAY during copying the on-screen
display will be recorded on the copied tape. Do not
press any button on the remote control except when
you want to stop copying.
During this recording, do not operate the REW and
FF functions. Otherwise it would record the fast
moving picture without sound on the tape.
Tape Remaining
This function displays the amount of time remaining on the tape during recording or playback.
Press DISPLAY repeatedly until the REM indicator displays on the TV screen during recording or
playback.
The remaining tape length may not be displayed
correctly depending on the condition of the tape and
the kind of the tape (T-140, T-160, or T-210 etc.).
Some of these functions will be displayed every
time the DVD+VCR is operated.
❶
❷
❸
❹
❺
HI-FI
REM 1:07
REMAINING TIME
Counter Memory
This feature is useful if there is a section of tape
you want to view immediately after recording or if
you want to return to the same point several
times.
1. Begin recording or playing a tape.
2. Press DISPLAY until the real-time counter is
displayed on the TV screen.
3. At the point that you want to locate later, reset
the real-time counter to “0:00:00” by pressing
CLEAR (0000).
4. Continue to play or record.
5. Press STOP (x) when recording or playback
finishes.
6 Press REW (m). The tape automatically
stops when the tape counter returns to about
“0:00:00”.
On-Screen Display - VCR
PLAY
SP
0:05:25
COUNTER
Operation
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
CH 4
STEREO
Notes:
•
OCT 8 , SAT
❻
❶ TAPE SPEED DISPLAY
❷ FUNCTION DISPLAY
❸ HI-FI DISPLAY
(Only when the HI-FI audio
sound is recorded)
2:15 PM
❼
❺ STEREO / SAP DISPLAY
(MONO is not displayed)
❻ DATE DISPLAY
❼ CLOCK / COUNT/
REMAIN DISPLAY
•
•
The function displays can be seen displayed on the
TV screen for 5 seconds.
The clock (or tape counter, tape remaining) mode
will be displayed until you press ENTER / OK.
The tape counter and the remaining tape length indicator appear only when a cassette is inserted. Also,
the remaining tape length indicator appears after
any tape operation.
❹ CHANNEL DISPLAY
25
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✺
Additional VCR Information
S-VHS Quasi Playback (SQPB)
•
During manual recording, timer recording,
Instant Timer Recording, playback, or fast forward modes, the DVD+VCR automatically
starts rewinding the tape at the end of the tape.
The cassette stops at the beginning of the tape
and is ejected.
•
This DVD+VCR can play back S-VHS recorded tapes, however, it cannot record video on
S-VHS format.
•
SQPB is an abbreviation for S-VHS Quasi
Playback.
After you have finished using the DVD+VCR,
rewind, eject, and remove the cassette. Place
the cassette in its protective sleeve to protect it
from dust. It is not necessary to rewind the cassette before removing it, but if you do, it is
ready to play or record the next time you use it.
Note:
•
•
•
Be sure the DVD+VCR channel selector is on
the correct channel you wish to record. The
channel that is being recorded can always be
checked by setting the television on the
DVD+VCR channel (CH 3 or 4) and pressing
the TV/VCR to turn the DVD+VCR’s TV indicator off.
Do not attempt to hook up more than one television set to the DVD+VCR for either recording or playback.
VCR Auto Play System
This DVD+VCR features automatic playback.
When you load a tape with the safety tab removed
the following occurs:
•
The Output Source is changed to VCR mode
automatically.
•
The power turns on automatically and playback
begins.
•
At the end of the tape, the DVD+VCR stops, then
rewinds.
•
The tape is ejected after rewinding and the turns
itself off automatically.
Playback picture of SQPB may be distorted in the following cases:
• When starting playback.
• When changing the playback mode between forward or reverse picture search and normal playback.
• When changing the operating deck (VCR or DVD).
Easy Information
If the Extended Data Service (XDS) signals are
provided along with normal TV signal in your area
or during playback of a tape recorded with
Extended Data Service (XDS) signals, the station
ID, program title, and program details are shown
on the TV screen. When viewing a channel with
Extended Data Service (XDS) signals, press
ENTER / OK and the station ID will appear on the
TV screen. Press ENTER / OK again and the program details will appear on the TV screen.
When viewing a tape recorded with Extended
Data Service (XDS) signals, press ENTER / OK
twice and the program title and program details
will appear on the TV screen.
Program Details
LENGTH: Indicates the run length of a program.
TIME REMAINING: Indicates the remaining time of
a program.
RATING: Indicates the rating of the current program
(N/A, G, PG, PG-13, R, NC-17, X and Not Rated).
The rating N/A means that the motion picture ratings
are not applicable to this program.
SP
WABC
“Home video”
APR 30 , SAT
Note:
Auto power off does not function during regular DVD
play mode. (DVD+VCR power stays on.)
CH 4
STEREO
2:15 PM
Easy Information Screen
(Station ID)
PROGRAM DETAILS
“Home video”
LENGTH 01:00
TIME REMAINING 00:26
RATING N/A
Easy Information Screen
(Program details)
26
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✻
Playing a DVD or V ideo CD
General Features
Note:
1. Turn on the TV and select the video input
source connected to the DVD+VCR.
2. Turn on the audio system (if applicable) and
select the input source connected to the
DVD+VCR.
3. Press OPEN/CLOSE (Z) to open the disc tray
and load your chosen disc in the tray, with the
playback side down.
4. Press OPEN/CLOSE (Z) to close the tray.
Playback starts automatically. If playback does
not start, press PLAY (N).
In some cases, the disc menu might appear
instead.
5. To stop the playback, press STOP (x).
The unit records the stopped point, depending
on the disc. “Xx” appears on the screen
briefly. Press PLAY (N) to resume playback
(from the scene point). If you press STOP (x)
again or unload the disc (“x” appears on the
screen.), the unit will clear the stopped point.
Press OPEN/CLOSE (Z) to remove the disc.
Press OPEN/CLOSE (Z) to close disc tray or
press POWER 1/:, the disc tray closes automatically and unit turns off.
Unless stated otherwise, all operations described use
the Remote Control. Some features may also be available on the Setup menu.
Moving to another TITLE
When a disc has more than one title, you can
move to another title. Press DISPLAY and select
desired title by using number (0-9) or b / B then
press ENTER / OK to move to another title.
Moving to another CHAPTER
DVD
Use the b B v V buttons to select the
title/chapter you want to view, then press
ENTER / OK to start. Press TITLE or DISC
MENU to return to the menu screen.
VCD
DVD
VCD
When a title on a disc has more than one chapter,
you can move to another chapter as follows:
•
Press SKIP (> or .) briefly during playback to select the next chapter or to return to
the beginning of the current chapter.
•
Press SKIP (.) twice in quick successions
to step back to the previous chapter.
•
To go directly to any chapter during DVD playback, press DISPLAY and press v / V to
select the chapter icon. Input the chapter number (0-9) or use b / B.
Slow Motion
If a menu screen is displayed
The menu screen may be displayed first after
loading a DVD which offer a menu.
DVD
DVD
Operation
Playback Setup
VCD
1. Press PAUSE (X) during playback.
The DVD+VCR will now go into PAUSE mode.
2. Use FF (M) to select the required speed: T
1/7, T 1/6, T 1/4, or T 1/2 (forward).
3. To exit Slow Motion mode, press PLAY (N).
Note:
Slow motion playback in reverse is not possible.
Use the number buttons to select the track you
want to view and press RETURN to return to
the menu screen. Menu settings and operating
procedures may differ. Follow the instructions
on each menu screen. You also may set PBC
to Off (See “PBC” on page 19).
Note:
DVDs may have a region code. Your player will not play
discs that have a region code different from your player.
The region code for this player is 1 (one).
27
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✶✼
Still Picture and Frame-by-Frame Playback
DVD
VCD
1. Press PAUSE (X) during playback. Advance
the picture frame-by-frame by pressing PAUSE
(X) repeatedly.
2. To exit still motion mode, press PLAY(N).
Search
DVD
VCD
1. Press REW (m) or FF (M) during playback.
2. Press REW (m) or FF (M) repeatedly to
select the required speed.
DVD: X2, X4, X16 or X100
VCD: X2, X4 or X8
3. To exit SEARCH mode, press PLAY (N).
Time Search
DVD
VCD
To start playing at any chosen time on the disc:
1. Press DISPLAY during playback. The time
search box shows the elapsed playing time.
2. Press v / V to select the time clock icon and
“-:--:--” appears.
3. Input the required start time in hours, minutes,
and seconds from left to right. If you enter the
wrong numbers, press CLEAR (0000) to
remove the numbers you entered. Then input
the correct numbers.
4. Press ENTER / OK to confirm. Playback starts
from the selected time.
Marker Search
DVD
VCD
To enter a Marker
You can start playback from up to nine memorized points. To enter a marker, press MARKER
at the desired point on the disc. The Marker icon
appears on the TV screen briefly. Repeat to enter
up to nine markers.
To Recall or Clear a Marked Scene
1. During disc playback, press SEARCH. The
marker search menu appears on the screen.
2. Within 10 seconds, press b / B to select a
marker number that you want to recall or clear.
3. Press ENTER / OK and playback starts from
the marked scene. Or, Press CLEAR (0000)
and the marker number is erased from the list.
4. You can play any marker by inputting its number on the marker search menu.
28
Repeat
DVD
VCD
You can repeat a title/chapter on a disc.
Press REPEAT during playback to select a
desired repeat mode.
DVD Video Discs - Repeat Chapter / Title / Off
• Chapter: repeats the current chapter.
• Title: repeats the current title.
• Off: does not play repeatedly.
Video CDs - Repeat Track / All / Off
• Track: repeats the current track.
• All: repeats all the tracks on a disk.
• Off: does not play repeatedly.
Notes:
•
•
On a Video CD with PBC, you must set PBC to Off
on the setup menu to use this function (See “PBC”
on page 19).
If you press > once during Repeat Chapter
(Track) playback, the repeat playback cancels.
Repeat A-B
DVD
VCD
A-B
To repeat a sequence.
1. Press REPEAT A-B at your chosen starting
point. “ A - ” appears briefly on the TV screen.
2. Press REPEAT A-B again at your chosen end
point.
“A - B” appears briefly on the TV screen and
the repeat sequence begins.
3. Press REPEAT A-B again to cancel.
Zoom
DVD
VCD
Use zoom to enlarge the video image.
1. Press ZOOM during playback or still playback
to activate the Zoom function. The square
frame appears briefly in the right bottom of the
picture.
2. Each press of ZOOM changes the TV screen
in the sequence: 100% size → 150% size →
200% size → 300% size → 400% size →
100% size
3. Use the b B v V buttons to move through the
zoomed picture.
4. To resume normal playback, press ZOOM
repeatedly or CLEAR (0000) button.
Note:
Zoom may not work on some DVDs or VCDs.
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
Changing the Audio Channel
✶✽
Special DVD Features
VCD
Press A.MONITOR repeatedly during playback to
hear a different audio channel (Stereo, Left,
Right).
Checking the contents of DVD discs:
Menus
Last Scene Memory
DVDs may offer menus that allow you to access
special features. To use the disc menu, press
DISC MENU. Input the corresponding number or
use the b B v V buttons to highlight your selection. Then press ENTER / OK.
DVD
VCD
CD
This player memorizes last scene from the last
disc that is viewed. The last scene remains in
memory even if you remove the disc from the
player or switch off the player. If you load a disc
that has the scene memorized, the scene is automatically recalled.
Note:
This player does not memorize the scene of a disc if you
switch off the player before commencing to play the
disc.
Title Menu
DVD
1. Press TITLE. If the current title has a menu,
the menu appears on the screen. Otherwise,
the disc menu may appear.
2. The menu offers features such as camera
angles, spoken language and subtitle options,
and chapters for the title.
3. Press TITLE to exit.
Screen Saver
Disc Menu
DVD
Press DISC MENU and the disc menu is displayed.
Press DISC MENU again to exit.
Note:
If here the sound from line out (or RF out) only, do not
select the dts sound; there is no audio from line out (or
RF out) when select the dts sound mode.
Camera Angle
Operation
The screen saver appears when you leave the
DVD+VCR in Stop mode for about five minutes.
DVD
If the disc contains scenes recorded at different
camera angles, you can change to a different
camera angle during playback. Press ANGLE
repeatedly during playback to select a desired
angle. Note that the number of the current angle
appears on the display.
Tip:
The Camera Angle icon is displayed on the TV screen
when alternate angles are available.
Changing the Audio Language
DVD
Press A.MONITOR repeatedly during playback to
hear a different audio language or audio track.
Subtitles
DVD
Press SUBTITLE repeatedly during playback to
see the different subtitle languages.
Note:
If there is no information,
is displayed.
29
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✴
On-Screen Display - DVD
Maintenance and Service
You can display the general playback status on
the TV screen. Some items can be changed using
the menu. To use the on-screen display:
Refer to the information in this chapter before
contacting a service technician.
1. Press DISPLAY during playback.
Handling the Unit
2. Press v / V to select an item.
The selected item is highlighted.
When shipping the unit
3. Press b / B to change the setting. You can
also use the number buttons if appropriate
(e.g. inputting the title number). For some
functions, press ENTER / OK to execute the
setting.
Notes:
•
Some discs may not provide all of the features
shown below.
•
If no button is pressed for 10 seconds, the onscreen display disappears.
•
If
is displayed, action prohibited or not available.
Example: On-Screen Display during
playing DVD Video
Items
Selection Method
Title Number
b / B, Numbers
ENTER / OK
Chapter Number
b / B, Numbers
ENTER / OK
Time search
Numbers,
ENTER / OK
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Keeping the exterior surfaces clean
•
Do not use volatile liquids such as insecticide
spray near the unit.
•
Do not leave rubber or plastic products in contact with the unit for a long period of time.
since they leave marks on the surface.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution.
Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.
Maintaining the Unit
The DVD+VCR is a high-tech, precision device. If
the optical pick-up lens and disc drive parts are
dirty or worn, the picture quality could be diminished.
Depending on the operating environment, regular
inspection and maintenance are recommended
after every 1,000 hours of use.
For details, please contact your nearest authorized service center.
30
✷✵
Playing an Audio CD Disc
Audio CD Disc Features
Audio CD
Once you insert an Audio CD a menu appears on
the TV screen. Press v / V to select a track then
press PLAY (N) or ENTER / OK and playback
starts.
Pause
CD
1. Press PAUSE (X) during playback.
2. To return to playback, press PLAY (N) or
press PAUSE (X) again.
Moving to another Track
CD
1. Press SKIP (> or .) briefly during playback to go to the next track or to return to the
beginning of the current track.
2. Press SKIP (.) twice in quick successions
to go back to the previous track.
3. You can play any track by inputting its number.
Repeat Track / All / Off
CD
You can play a track/all on a disc.
1. Press REPEAT when playing a disc. The
repeat icon appears.
2. Press REPEAT to select a desired repeat
mode.
Operation
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
• Track: repeats the current track.
• All: repeats all the tracks on a disc.
• Off(No display): does not play repeatedly.
Note:
If you press SKIP (>) once during Repeat Track
playback, the repeat playback will be cancelled.
31
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
Search
✷✶
Programmed Playback
CD
1. Press REW (m) or FF (M) during playback.
2. Press REW (m) or FF (M) repeatedly to
select the required speed:
X2, X4 and X8 backward or forward.
3. To exit SEARCH mode, press PLAY (N).
Random
CD
1. Press RANDOM during playback. Random
Playback begins immediately and “Random”
appears on the menu screen.
The program function enables you to store your
favorite tracks from any disc in the player
memory.
A program can contain 30 tracks.
1. Insert a disc.
AUDIO CD menu appears.
2. Press PROGRAM.
The E mark will appear to the right of the
word “Program” on the right side of the menu
screen.
2. To return to normal playback, press RANDOM
repeatedly until “Random” disappears from the
menu screen.
Tip:
By pressing SKIP (> or .) during random playback,
the unit selects another track and resumes random playback.
Repeat A-B
Audio CD Program Menu
CD
1. To repeat a sequence during disc playback
press REPEAT A-B at your chosen starting
point. The Repeat icon and “A -” appear on the
menu screen.
Note:
Press PROGRAM again, the E mark will
disappear to exit the Program Edit mode.
2. Press REPEAT A-B again at your chosen end
point. The Repeat icon and “A-B” appear on
the menu screen, and the sequence begins to
play repeatedly.
3. Select a track on the “List”, then press ENTER
/ OK to place the selected track on the
“Program” list. Repeat to place additional
tracks on the list.
3. To exit the sequence and return to normal
play, press REPEAT A-B again. The Repeat
icon disappears from the menu screen.
4. Press B.
Select the track you want to start playing on
the “Program” list.
5. Press PLAY (N) or ENTER / OK to start.
Playback begins in the order in which you programmed the tracks. Playback stops after all
of the tracks on the “Program” list have played
once.
6. To resume normal playback from programmed
playback, select a track of AUDIO CD list and
then press PLAY (N).
32
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✷
Repeat Programmed Tracks
1. Press REPEAT when playing a disc. The
repeat icon appears.
2. Press REPEAT to select a desired repeat
mode.
• Track: repeats the current track
• All: repeats all the tracks on programmed list.
• Off (No display): does not play repeatedly.
Note:
If you press SKIP (> ) once during Repeat Track
playback, the repeat playback will be cancelled.
Erasing a Track from “Program” List
1. During STOP mode, press PROGRAM and
mark will appear.
E
2. Use B / v / V to select the track that you wish
to erase from the Program list.
3. Press CLEAR (0000). Repeat to erase additional tracks on the list.
Erasing the Complete Program List
E
Operation
1. During STOP mode, press PROGRAM and
mark will appear.
2. Use B / v / V to select “Clear All” in the
“Program” list, then press ENTER / OK.
Note:
The programs are also cleared when the disc is
removed.
33
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✸
V iewing a JPEG Disc
Slide Show
Using this DVD+VCR you can view discs with
JPEG files.
Use v V b B to highlight the
then press ENTER / OK.
1. Insert a disc and close the tray. The PHOTO
menu appears on the TV screen.
Still Picture
JPEG
(Slide Show)
JPEG
1. Press PAUSE (X) during slide show.
The player will now go into PAUSE mode.
2. To return to the slide show, press PLAY (N)
or press PAUSE (X) a gain.
Moving to another File
JPEG
Press SKIP (> or .) or cursor (b or B) once
while viewing a picture to advance to the next or
previous file.
Zoom
2. Press v / V to select a folder, and press
ENTER / OK. A list of files in the folder
appears.
If you are in a file list and want to return to the
previous Folder list, use the v / V buttons on
the remote to highlight
and press ENTER
/ OK.
3. If you want to view a particular file, press v / V
to highlight a file and press ENTER / OK or
PLAY (N). The selected file will appear for
viewing.
While viewing a file, you can press STOP (x)
to move to the previous menu (PHOTO
menu).
Tips:
•
Information and user guidance regarding the current
image is displayed in the lower part of the screen.
You can toggle this bar on and off using RETURN
(O).
•
There are three Slide Speed options
:
>>> (Fast), >> (Normal) and > (Slow)
Use v V b B to highlight the Speed. Then, use b /
B to select the option you want to use then press
ENTER / OK.
JPEG
Use zoom to enlarge the photo image. (see page
28)
To rotate picture
JPEG
Press v / V during showing a picture to rotate the
picture clockwise or counter clockwise.
JPEG disc compatibility with this player
is limited as follows:
• Depending upon the size and number of
JPEG files, it could take a long time for the
DVD+VCR to read the disc’s contents. If you
don’t see an on-screen display after several
minutes, some of the files may be too large —
reduce the resolution of the JPEG files to less
than 5760 (Horizontal) x 3840 (Vertical) pixels
and burn another disc.
• The total number of contents on the disc
should be less than 1500 files and 300 folders.
• Some discs may be incompatible due to a different recording format or the condition of
disc.
• Ensure that all the selected files have the
“.jpg” extensions when copying into the CD
layout.
• If the files have “.jpe” or “.jpeg” extensions,
please rename them as “.jpg” file.
• File names without “.jpg” extension will not be
able to be read by this DVD+VCR. Even
though the files are shown as JPEG image
files in Windows Explorer.
34
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✹
Reference
Language Codes
Use this list to input your desired language for the following initial settings:
Disc Audio, Disc Subtitle, Disc Menu.
Language
Abkhazian
Afar
Afrikaans
Albanian
Ameharic
Arabic
Armenian
Assamese
Aymara
Azerbaijani
Bashkir
Basque
Bengali; Bangla
Bhutani
Bihari
Breton
Bulgarian
Burmese
Byelorussian
Cambodian
Catalan
Chinese
Corsican
Croatian
Czech
Danish
Dutch
English
Esperanto
Estonian
Faroese
Code
6566
6565
6570
8381
6577
6582
7289
6583
6588
6590
6665
6985
6678
6890
6672
6682
6671
7789
6669
7577
6765
9072
6779
7282
6783
6865
7876
6978
6979
6984
7079
Language
Code
Fiji
7074
Finnish
7073
French
7082
Frisian
7089
Galician
7176
Georgian
7565
German
6869
Greek
6976
Greenlandic
7576
Guarani
7178
Gujarati
7185
Hausa
7265
Hebrew
7387
Hindi
7273
Hungarian
7285
Icelandic
7383
Indonesian
7378
Interlingua
7365
Irish
7165
Italian
7384
Japanese
7465
Javanese
7487
Kannada
7578
Kashmiri
7583
Kazakh
7575
Kirghiz
7589
Korean
7579
Kurdish
7585
Laothian
7679
Latin
7665
Latvian, Lettish 7686
Language
Lingala
Lithuanian
Macedonian
Malagasy
Malay
Malayalam
Maltese
Maori
Marathi
Moldavian
Mongolian
Nauru
Nepali
Norwegian
Oriya
Panjabi
Pashto, Pushto
Persian
Polish
Portuguese
Quechua
Rhaeto-Romance
Rumanian
Russian
Samoan
Sanskrit
Scots Gaelic
Serbian
Serbo-Croatian
Shona
Sindhi
Code
7678
7684
7775
7771
7783
7776
7784
7773
7782
7779
7778
7865
7869
7879
7982
8065
8083
7065
8076
8084
8185
8277
8279
8285
8377
8365
7168
8382
8372
8378
8368
Language
Singhalese
Slovak
Slovenian
Somali
Spanish
Sudanese
Swahili
Swedish
Tagalog
Tajik
Tamil
Tatar
Telugu
Thai
Tibetan
Tigrinya
Tonga
Turkish
Turkmen
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Welsh
Wolof
Xhosa
Yiddish
Yoruba
Zulu
Code
8373
8375
8376
8379
6983
8385
8387
8386
8476
8471
8465
8484
8469
8472
6679
8473
8479
8482
8475
8487
8575
8582
8590
8673
8679
6789
8779
8872
7473
8979
9085
Area Codes
Choose an area code from this list.
Code
AF
AR
AU
AT
BE
BT
BO
BR
KH
CA
CL
CN
CO
CG
CR
HR
CZ
DK
EC
EG
SV
Area
Ethiopia
Fiji
Finland
France
Germany
Great Britain
Greece
Greenland
Islands
Hong Kong
Hungary
India
Indonesia
Israel
Italy
Jamaica
Japan
Kenya
Kuwait
Libya
Luxembourg
Code
ET
FJ
FI
FR
DE
GB
GR
GL
HM
HK
HU
IN
ID
IL
IT
JM
JP
KE
KW
LY
LU
Area
Code
Malaysia
MY
Maldives
MV
Mexico
MX
Monaco
MC
Mongolia
MN
Morocco
MA
Nepal
NP
Netherlands
NL
Netherlands Antilles AN
New Zealand
NZ
Nigeria
NG
Norway
NO
Oman
OM
Pakistan
PK
Panama
PA
Paraguay
PY
Philippines
PH
Poland
PL
Portugal
PT
Romania
RO
Russian Federation RU
Area
Code
Saudi Arabia
SA
Senegal
SN
Singapore
SG
Slovak Republic
SK
Slovenia
SI
South Africa
ZA
South Korea
KR
Spain
ES
Sri Lanka
LK
Sweden
SE
Switzerland
CH
Taiwan
TW
Thailand
TH
Turkey
TR
Uganda
UG
Ukraine
UA
United States
US
Uruguay
UY
Uzbekistan
UZ
Vietnam
VN
Zimbabwe
ZW
Reference
Area
Afghanistan
Argentina
Australia
Austria
Belgium
Bhutan
Bolivia
Brazil
Cambodia
Canada
Chile
China
Colombia
Congo
Costa Rica
Croatia
Czech Republic
Denmark
Ecuador
Egypt
El Salvador
35
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✺
Troubleshooting
Check the following guide for the possible cause of a problem before contacting service.
Symptom
Cause
No power.
The power cord is disconnected.
Plug the power cord into the wall
outlet securely.
The power is on, but
the DVD+VCR does
not work.
DVD or VCR button is not switched
properly.
Refer to page 7.
No disc is inserted.
Insert a disc or tape. (Check that
the disc or tape indicator in the display window is lit.)
No tape is inserted.
No picture.
No sound.
The playback picture
is poor.
The “PROGRESSIVE
SCAN MODE”
message remains to
be displayed.
36
Correction
The TV is not set to receive DVD +
VCR signal output.
Select the appropriate video input
mode on the TV so the picture from
the DVD+VCR player appears on
the TV screen.
The video cable is not connected
securely.
Connect the video cable into the
jacks securely.
Wrong connection.
Check the connection.
The equipment connected with the
audio cable is not set to receive
DVD+VCR signal output.
Select the correct input mode of
the audio receiver so you can listen
to the sound from the DVD+VCR.
The audio cables are not connected
securely.
Connect the audio cable into the
jacks securely.
The power of the equipment connected with the audio cable is turned off.
Turn on the equipment connected
with the audio cable.
The AUDIO options are set to the
wrong position.
Set the AUDIO options to the correct position.
The disc is dirty.
Clean the disc.
The TV channels are not tuned in
properly.
Check tuning, carry out tuning
again.
Tape heads are dirty.
Clean video heads.
Tape is a rental or was recorded on
another VCR.
Use CH -/+ for manual tracking
adjustment while tape is playing.
This unit can only output 525p
Progressive scan picture.
Make sure that your TV can support 525p Progressive scan picture
or set Progressive scan to off.
DVD+VCR was turned off while setting the Progressive scan mode.
x) for more
Keep pressing STOP (x
than 5 seconds.
The Progressive Scan is set to On on
the setup menu but is connected to a
standard(analog) television with component video input.
Symptom
✷✻
Cause
Correction
An unplayable disc is inserted.
Insert a playable disc. (Check the
disc type and Regional code.)
The disc is placed upside down.
Place the disc with the playback side
down.
The disc is not placed within the
guide.
Place the disc on the disc tray correctly inside the guide.
The disc is dirty.
Clean the disc.
Video tape cannot be
inserted.
Is the cassette compartment
empty?
Eject the tape in.
No Hi-Fi sound
Audio mode is not set properly.
Select STEREO by repeatedly
pressing A.MONITOR on the
Remote Control.
The Remote Control
does not work
properly.
There is an obstacle in the path of
the Remote Control and this unit.
Remove the obstacle.
The batteries in the Remote Control
are exhausted.
Replace the batteries with new ones.
The Remote Control is not pointed
at the remote sensor of the
DVD+VCR.
Point the Remote Control at the
remote sensor of the DVD+VCR.
The Remote Control is too far from
the DVD+VCR.
Operate the Remote Control within
23ft (7m).
This Remote Control use the same
buttons for VCR and DVD functions
(ex.PLAY).
When using a VCR, first press the
VCR button. When using a DVD, first
press the DVD button.
The Remote Control of a JVC TV or
Receiver cannot operate the DVD+
VCR.
Use the DVD+VCR’s Remote
Control.
Camcorder image is
not shown.
Camcorder is off.
Turn camcorder on and operate
properly.
Camcorder image via
AV input to
DVD+VCR is not
shown on TV screen.
DVD+VCR SOURCE SELECT is
not set to LINE1 or LINE2.
Press AUX to select LINE input
channel (LINE1 or LINE2).
Timer recording is not
possible.
Clock in DVD+VCR is not set to
correct time.
Set clock to correct time.
Timer has been programmed
incorrectly.
Reprogram Timer.
indicator light does not appear
after programming timer.
Reprogram Timer and turn
DVD+VCR off to enable timer.
The DVD+VCR does
not start playback.
Reference
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
37
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✼
Specifications
General
Power requirements
Power consumption
Dimensions (approx.)
Weight (approx.)
Operating temperature
Operating humidity
Signal system
120 V, 60 Hz
16 W ✬❖O❉◗ ON✭
✴✲✼  ✬❘❙❅N❈❆ ❧o❝❞✭
16.9" X 3.1" X 10.4" (430 X 78.5 X 265 mm) (w x h x d)
9.24 lbs (4.2 kg)
5˚C to 40˚C (41˚F to 104˚F)
5 % to 90 %
NTSC
Inputs
ANTENNA IN
VHS VIDEO IN(LINE1, 2)
VHS AUDIO IN(LINE1, 2)
75 ohms (VHF/UHF/CATV)
1 V (p-p) 75 ohms, sync negative, RCA jack x 2
-6.0 dBm more than 47 ohms, RCA jack (L, R) x 2
Outputs
VIDEO OUT
COMPONENT VIDEO OUT
(PROGRESSIVE SCAN)
Audio output (digital audio)
Audio output (analog audio)
RF OUT
1 V (p-p) 75 ohms, sync negative
(Y) 1.0 V (p-p), 75 ohms, negative sync, RCA jack x 1
(Pb)/(Pr) 0.7 V (p-p), 75 ohms, RCA jack x 2
0.5 V (p-p), 75 ohms, RCA jack x 1
2.0 Vrms (1 KHz, 0 dB), 600 ohms, RCA jack (L, R) x 1
Channel 3 or 4 (Adjustable)
VCR Specifications
Head system
Timer
Tape speed
Tape width
Maximum recording time
Rewind time
Channel coverage
Frequency range
Signal-to-noise ratio
Dynamic range
Channel separation
Four head helical scan azimuth system
12-hour display type with AM, PM
SP: 33.35 mm/sec, LP: 16.67 mm/sec, SLP: 11.12 mm/sec
12.7 mm
SP: 2 HOURS (T-120), SLP: 6 HOURS (T-120)/8 HOURS (T-160)
About 3 minutes (T-120)
VHF: 2-13, UHF: 14-69, CATV: 1-125 (4A, A-W, W+1 - W+84, A-5 - A-1)
20 Hz to 20 kHz
More than 43 dB
More than 88 dB
More than 60 dB
DVD Specifications
Laser system
Frequency response
Signal-to-noise ratio
Harmonic distortion
Dynamic range
Semiconductor laser, wavelength 650 nm
DVD (PCM 96 kHz): 8 Hz to 44 kHz,
DVD (PCM 48 kHz): 8 Hz to 22 kHz
CD: 8 Hz to 20 kHz
More than 100 dB (ANALOG OUT jacks only)
Less than 0.008%
More than 95 dB (DVD/CD)
Accessories:
RF 75-ohm Coaxial Cable x 1, Remote control x 1, Batteries (R03/AAA) x 2
• Design and specifications are subject to change without prior notice.
38
H◗❇✵✼❆❚❘✵✽❘❚❘✸✲✵✤ ✤ ✴✹✲✺✲✵✸✤ ✤ ✵✵✾✴✻✤ ❅M✤ ✤ y
✷✽
Reference
Warranty (Only in U.S.A.)
39
HR-XVC18BUS/HR-XVC19SUS
US
Cover_HR-XVC18&19US.indd 2
Printed in Indonesia
0605STH-MW-OT
05.6.10 2:00:53 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement