The most trusted, dependable name in projector lamp sales.

The most trusted, dependable name in projector lamp sales.
The most trusted, dependable name
in projector lamp sales.
http://www.myprojectorlamps.com
http://www.myprojectorlamps.ca
http://www.myprojectorlamps.eu
The following projector manual has not been modified or altered in any way.
IN1100 IN1102
Regulatory models W1100 and W1102
010-0712-02
Declaration of Conformity
FCC Warning
Manufacturer: InFocus Corporation, 27500 SW Parkway Ave. Wilsonville, Oregon
97070 USA
European Office: Louis Armstrongweg 110, 1311 RL Almere, The Netherlands
We declare under our sole responsibility that this projector conform to the
Note: This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by InFocus Corporation may void
authority to operate the equipment.
following directives and norms:
EMC Directive 2004/108/EC
EMC: EN 55022
EN 55024
EN 61000-3-2
EN 61000-3-3
Low Voltage Directive 2006/95/EC
Safety: IEC 60950-1: 1st Edition
Trademarks
DisplayLink is a trademark of DisplayLink Corporation.
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of Apple
Computer, Inc. IBM is a trademark or registered trademark of International Business
Machines, Inc. Microsoft, PowerPoint, and Windows are trademarks or registered
trademarks of Microsoft Corporation. Adobe and Acrobat are trademarks or
registered trademarks of Adobe Systems Incorporated. DLP® and the DLP logo are
registered trademarks of Texas Instruments and BrilliantColor™ is a trademark of
Texas Instruments. InFocus, In Focus, and INFOCUS (stylized) are either registered
trademarks or trademarks of InFocus Corporation in the United States and other
countries.
Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Agency Approvals
UL, cUL
Other specific Country Approvals may apply. Please see product certification label.
This document applies to regulatory models W1100 and W1102.
Input ratings: 100-240Vac, 2.3-0.9A, 50-60Hz
InFocus reserves the right to alter product offerings and specifications at any time
without notice.
1
Table of Contents
Introduction
Positioning the projector
Projector and device connector guide
Connecting a computer source
Required computer connections
(DisplayLink or VESA)
Optional computer connections
Displaying an image
Adjusting the image
Connecting a video device
Video device connections
Composite video connection
S-video connection
VESA connection
Component video connection
Shutting down the projector
Troubleshooting your setup
Using the remote control
Using the audio
Using the keypad buttons
Optimizing computer images
Presentation features
Optimizing video images
Customizing the projector
Using the menus
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Maintenance
Cleaning the lens
Using the security lock
Replacing the projection lamp
Important Operating Considerations for Safety
3
5
6
9
•
9
9
10
11
12
13
13
13
13
13
14
14
22
23
24
25
25
26
26
27
28
29
30
32
33
33
33
34
•
•
•
•
•
Place the projector in a horizontal position no greater than 15 degrees
off axis.
Locate the projector in a well-ventilated area without any obstructions
to intake or exhaust vents. Do not place the projector on a tablecloth or
other soft covering that may block the vents.
Locate the projector at least 4' (1.2 m) away from any heating or cooling
vents.
Only genuine InFocus lamps are tested for use in this projector.
InFocus is not liable for the performance, safety or certification of any
other lamps. The use of other lamps violates the projector warranty and
voids all certification marks on this projector.
Use only the power cord provided. A surge-protected power strip is
recommended.
Refer to this guide for proper startup and shutdown procedures.
•
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
•
In the unlikely event of a lamp rupture, particles may exit through the
projector side vents. When the projector is turned on, keep people,
food, and drinks out of the "keep out" area under and around the
projector, as indicated by the "X" areas below.
3’
/1
m
.6 m
2’ / 0
Follow these instructions to help ensure image quality and lamp life over
the life of the projector. Failure to follow these instructions may affect the
warranty. For complete details of the warranty, see the Warranty Booklet.
2
Introduction
Your new digital projector is simple to connect, easy to use, and
straightforward to maintain. It is a versatile projector that is flexible enough
for business presentations and home video viewing too. The IN1100 has
native XGA 1024x768 resolution, and the IN1102 has WXGA 1280x800
resolution. This guide applies to all products. They are compatible with a
wide variety of computers and video devices.
touch keypad
Product specifications
To read the latest specifications on your multimedia projector, be sure to
visit our website at www.infocus.com, as specifications are subject to
change.
remote control
receiver (IR)
Accessories
zoom (rear ring)
focus (front ring)
The standard accessories that came with your projector are listed in the
included Quick Start Poster/Booklet. Optional accessories can be found on
our website at www.infocus.com or at your retailer or dealer.
lens
Online registration
Register your projector on our website at www.infocus.com/register to
activate your warranty and receive product updates, announcements, and
registration incentives.
remote control
receiver (IR)
power cord
connector
security lock
elevator foot
3
connector
panel
Connector panel
The projector provides the following connectors:
•
VESA computer
•
S-video
•
Composite video
•
Audio in
•
USB DisplayLink connector, for computer video input. This USB
connection also provides slide advance (and mouse control when used
with an optional remote control only)
computer
DisplayLink
connector
composite
video
S-video
audio in
security lock
4
Positioning the projector
Table 1: (IN1100)
Range of distance to the screen for a given screen size
To determine where to position the projector, consider the size and shape of
your screen, the location of your power outlets, and the distance between the
projector and the rest of your equipment. Here are some general guidelines:
•
Position the projector on a flat surface at a right angle to the screen. The
projector must be at least 4.9 feet (1.5m) from the projection screen.
•
Position the projector within 10 feet (3m) of your power source and
within 6 feet (1.8m) of your video device (unless you purchase
extension cables). To ensure adequate cable access, do not place the
projector within 6 inches (.15m) of a wall or other object.
•
Position the projector the desired distance from the screen. The
distance from the lens of the projector to the screen, the zoom setting,
and the video format determine the size of the projected image.
•
The image exits the projector at a given angle. IN1100 image offset is
115%; IN1102 image offset is 112.4%. This means that if you have an
image 10’ high, the bottom of the image will be 1.5' (IN1100) and 1.24'
(IN1102) above the center of the lens.
10 ft high
image
(IN1102)
bottom of image
1.24 ft above center
of lens
lens center
Projection angle
10 ft high
image
Distance to screen
Maximum
distance
(feet/m)
Minimum
Distance
(feet/m)
60/1.5
80/2.0
90/2.3
150/3.8
8.6/2.6
11.5/3.5
12.9/3.9
21.5/6.6
7.8/2.4
10.4/3.2
11.7/3.6
19.5/5.9
Table 2: (IN1102)
Range of distance to the screen for a given screen size
Distance to screen
(IN1100)
bottom of image
1.5 ft above center
of lens
Diagonal
Screen Size
(inches/m)
Projection angle
lens center
5
Diagonal
Screen Size
(inches/m)
Maximum
distance
(feet/m)
Minimum
Distance
(feet/m)
60/1.5
80/2.0
90/2.3
150/3.8
7.2/2.2
9.6/2.9
10.8/3.3
18.0/5.5
6.6/2.0
8.8/2.7
9.9/3.0
16.4/5.0
Projector and device connector guide
The following illustration and table should help you find the connectors to
use and obtain the best resolution possible from your input devices, such as
computers, standard VCRs, DVD players (progressive and interlaced),
HDTV sources (1080i, 1080p and 720p HDTV formats), TV and satellite
tuners, camcorders, video games (progressive and interlaced), and laser
disc players.
computer
composite
video
S-video
DisplayLink
connector
audio in
security lock
6
Video Device
Standard Broadcast TV (not
HDTV) via: cable, digital
cable, satellite TV, DVD, or
VCR
Standard Video Camera
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
Comments
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or Video 1
Composite video connection on
page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
S-video connection on page 13
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or Video 1
Composite video connection on
page 13.
Not for progressive
(i.e. HDTV) sources.
See page 8.
S-video connection on page 13
Standard Video Game
NTSC, PAL, and
SECAM formats
Composite video
or S-video
Video 2
or Video 1
Composite video connection on
page 13.
S-video connection on page 13
7
Not for progressive
(i.e. HDTV) sources.
See page 8.
Video Device
HDTV
(High Definition TV)
Video
Compatibility
If Your Device
Connector Is
Attach to Adapter
or Labeled
Connector on
Projector
For Setup Instructions, see
1080i, 1080p, 720p
VGA
Computer 2
VESA connection on page 13
Component 480i
Component video
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 13
1080i, 1080p, 720p
VGA
Computer 2
VESA connection on page 13
Component 480p
and 480i
Component video
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 13
1080i, 1080p, 720p
VGA
Computer 2
VESA connection on page 13
Component 480p
and 480i
Component video
Computer 2 via
optional VESA to
Component adapter
Component video connection on
page 13
Progressive DVD
Progressive Video Game
8
Comments
Connecting a computer source
connect USB cable
Required computer connections (DisplayLink or
VESA)
If your computer has Windows XP SP2 or newer*, connect the USB cable
between your computer's USB port and the projector's DisplayLink
connector, then follow the instructions on the screen. See the DisplayLink
Manager User's Guide for more information.
MOLEX
MOLEX
* For the latest information about support for other operating systems
(including Apple), go to www.infocus.com/support/displaylink.
connect power cord
Or, connect one end of the provided computer cable to the Computer 2
connector on the projector and the other to the VESA connector on your
computer. If you are using a desktop computer, you will need to disconnect
the monitor cable from the computer’s video port first.
Connect the black power cord to the Power connector on the side of the
projector and to your electrical outlet. The Power light on the Status
Indicator Panel (page 14) turns amber.
connect computer cable
NOTE: Always use the power cord that shipped with the projector.
Optional computer connections
To get sound from the projector, connect an audio cable (optional cable, not
included) to your computer and to the Audio In connector on the projector.
You may also need an adapter.
connect audio cable
To advance slides in a PowerPoint presentation using the remote control,
plug the USB cable into the USB mouse connector on your computer and
the DisplayLink connector on the projector.
9
Displaying an image
press Power button
Touch the Power button.
The Power button blinks green and the fans start to run. When the lamp
comes on, the start up screen displays and the Power button is steady green.
It can take a minute for the image to achieve full brightness.
? No start up screen? Get help on page 15.
turn on computer or
video device
Turn on your computer or video device.
The image should appear on the projection screen. If it doesn’t, press the
Source button on the projector’s keypad or remote.
If you are using a VESA cable to connect your computer to the
projector (instead of DisplayLink):
If using a laptop, make sure its external video port is active.
Many laptops do not automatically turn on their external video port when a
projector is connected. Usually a key combination like FN + F8 or CRT/
LCD key turns the external display on and off. Locate a function key labeled
CRT/LCD or a function key with a monitor symbol. Press FN and the
labeled function key simultaneously. Refer to your laptop’s
documentation to learn your laptop’s key combination.
activate laptop’s external port
monitor key or
LCD/CRT key
FN key
? No laptop image? Try pressing the Auto Image button on the
keypad. Get help on page 15.
? Is your laptop connected to the projector's DisplayLink
connector? See the InFocus DisplayLink Manager User's Guide for
troubleshooting information.
10
Adjusting the image
adjust height
If necessary, adjust the height of the projector by pressing the elevator foot
release button to extend the foot.
release button
If necessary, rotate the leveling foot located at the rear of the projector.
Avoid placing your hands near the hot exhaust vent at the side of the
projector.
elevator foot
Position the projector the desired distance from the screen at a 90 degree
angle to the screen.
adjust distance
See page 5 for a table listing screen sizes and distances.
Adjust the zoom or focus, as needed.
adjust zoom or focus
zoom (rear ring)
focus (front ring)
If the image is not square, first make sure that the projector is perpendicular
to the screen. If the image is larger or smaller on the top or bottom edge of
the screen, press the top Keystone button to reduce the upper part of the
image, and press the bottom Keystone button to reduce the lower part.
adjust keystone
If the left or right side of the screen is larger or smaller the other, you can
turn the projector to the left or to the right a few degrees to square the
image.
Adjust the Contrast or Brightness in the Basic Picture menu. See page 28 for
help with these menu adjustments.
adjust Basic Picture menu
For Aspect Ratio, keep in mind that DVD players must be configured for
16:9 in order to view the highest quality image. For more information
regarding Aspect Ratio, see page 12.
11
Connecting a video device
4:3 screen
You can connect video devices such as VCRs, DVD players, camcorders,
digital cameras, video game consoles, HDTV receivers, and TV tuners to the
projector. You can connect the audio directly to the projector to get sound
from the built-in speaker, or you can bypass the projector’s audio system
and connect the audio directly from your source to a stereo or home theater
system.
16:9 screen
Do Not Use
4:3
mode
You can connect the projector to most video devices that can output video.
You cannot directly connect the coaxial cable that enters your house from a
cable or satellite company, the signal must pass through a tuner first.
Examples of tuners are digital cable boxes, VCRs, digital video recorders,
and satellite TV boxes. Basically, any device that can change channels is
considered a tuner.
Before connecting your projector, you should decide which aspect ratio you
want to use. The projector’s Aspect Ratio setting is accessed through the
Resize button on the remote or through the projector’s Basic Picture Menu.
See page 28 for more information.
16:9
mode
What is Aspect Ratio?
Aspect ratio is the ratio of the image width to image height. TV screens are
usually 4:3. HDTV and most DVDs are 16:9. If you’re projecting onto a
screen, the size/shape of the screen may determine which aspect ratio to
use. If you are projecting onto a blank wall, you don’t have the screen size
restriction. What you plan to project will also help you choose between 4:3
and 16:9. Most TV shows are 4:3, while most movies are 16:9.
Native
mode
(NTSC
only)
If you have a 16:9 screen then you should select an aspect ratio of 16:9 for
anamorphic movies or HDTV, and Native for 4:3 content. If you have a 4:3
screen you should still use 16:9 for anamorphic movies or HDTV, but you
also have the option of using either 4:3 (to fill the screen) or Native (for
direct pixel mapping) for 4:3 content. Keep in mind that anamorphic movies
only appear correctly if the DVD player is set to output to a 16:9 television.
12
Video device connections
Component video connection
No video cables are provided with the projector. You can order cables from
InFocus or provide your own.
If your HD video device has component connectors, an optional
Component to VESA adapter can be used. Plug the component cable into
the video device. Plug the other end of the component cable into the adapter
and plug the adapter into the Computer 2 connector. Component offers the
highest quality video output.
Composite video connection
Plug the composite video cable’s yellow connector into the video-out
connector on the video device. Plug the other yellow connector into the
yellow Video 2 connector on the projector.
Plug the white connector of a Mini-plug audio Y-cable into the left audio
out connector on the video device and plug the red connector into the right
audio out connector on the video device. Plug the other end of the cable into
the Audio In connector on the projector.
Keep in mind that video output from composite connections is not as high
quality as S-video.
S-video connection
If your video device uses a round, four-prong S-video connector, plug an Svideo cable into the S-video connector on your video device and into the
Video 1 connector on the projector. Use the audio cable as described above.
Keep in mind that S-video delivers higher quality video output than
composite.
VESA connection
If your video device has a 15-pin VGA output, plug one end of the included
computer cable into the VGA connector on your video source. This
connector may be labeled “To Monitor” on the video source. Plug the
computer cable into the Computer 2 connector on the projector.
13
Shutting down the projector
The Status Indicator Panel on top of the projector indicates the state of the
projector and can help you troubleshoot.
The projector automatically displays a black screen after no active source is
detected for 30 minutes. This black screen helps preserve the life of the
projector. The image returns when an active source is detected or a remote
or keypad button is pressed.
Table 3: Status indicator light behavior and meaning
Screen Save Time
You can make the black screen appear after a preset number of minutes by
turning on the Screen Save Time feature in the Setup menu. See page 30.
Auto Off Time
The projector also has an Auto Off Time feature that automatically turns the
projector off after no active sources are detected and no user interaction
with the projector is performed for 30 minutes. By default, this feature is off.
You can change the length of time, see page 30.
Turning off the projector
To turn the projector off, press the Power button on the remote or keypad.
The lamp turns off and the LED blinks amber for 1 minute while the fans
continue to run to cool the lamp. When the lamp has cooled, the LED lights
amber and the fans stop. Unplug the power cable to completely power off
the projector.
Status Indicator Panel icons
Meaning
Power, solid amber
The projector is plugged in.
Power, blinking green
The power button has been pressed and
the software is initializing.
Power, solid green
The projector is on and initialized.
Power, blinking amber
The power button has been pressed to
turn the projector off and the fans are
running to cool the projector.
Thermometer
The projector is too hot. Make sure the
vents aren’t blocked (see page 20). Turn off
the projector and wait one minute, then
turn the projector on again. Visit
www.infocus.com/support to contact
service.
Lamp
Turn off the projector and wait one
minute, then turn the projector on again.
If the lamp light turns on again, replace the
lamp and reset the lamp timer.
Wrench/Service
Turn off the projector and wait one
minute, then turn the projector on again. If
the service lamp turns on again, service is
required. Visit www.infocus.com/support
to contact Service.
Troubleshooting your setup
If your image appears correctly on the screen, skip to the next section. If it
does not, troubleshoot the setup.
14
Problem
Solution
Result
No start up screen
Plug power cord into the projector press
power button
Correct image
Startup
Screen
A
Only start up screen appears
Startup
Screen
If your computer is using the projector's
DisplayLink connector, see the DisplayLink
User's Guide for troubleshooting
information.
Computer image projected
Press the Source button
activate laptop’s external port
A
A
A
Restart laptop
15
Problem
Solution
Result
No computer image, just the words
“Signal out of range”
Press the Auto Image button on keypad adjust computer Computer image projected
refresh rate in Control Panel > Display > Settings >
Advanced > Adapter (location varies by operating system)
A
of
Signal out
the range
A
A
You may also need to set a different resolution on your
computer, as shown in the following problem, “image
fuzzy or cropped”
Only my laptop’s background appears, not If your computer is using the DisplayLink connector, use Background and Desktop projected
DisplayLink Manager software to change the display
the Desktop icons
mode from Extended Desktop to Duplicated Desktop.
See the DisplayLink Manager User's Guide for more
information.
A
A
A
Disable “Extend my Windows
Desktop” in Control Panel >
Display > Settings > Display 2
(location varies by operating
system)
A
Uncheck this
option, then
click Apply
16
Problem
Solution
Result
Image fuzzy or cropped
Set your computer’s display resolution to the native
resolution of the projector (Start > Settings > Control
Panel > Display > Settings tab)
Image clear and not cropped
A
A
Image not centered on screen
A
For a laptop,
disable laptop
monitor or
turn-on dualdisplay mode
Move projector, adjust zoom, adjust height
A
Adjust horizontal
or vertical position
in Advanced
Picture menu
17
Correct image
Problem
Solution
Result
Image not square
Adjust Keystone on keypad
Square image
Image not sharp
Adjust Sharpness in the Basic Picture menu
Correct image
AB
Image does not fit 4:3 or 16:9 screen
AB
Change aspect ratio to 4:3 or 16:9 in Basic Picture >
Aspect ratio menu
18
Correct image
Problem
Solution
Result
Image reversed left to right
Turn off Rear Project in Setup menu
Correct image
A
Projected colors don’t match source
AB
Adjust color, tint, brightness, contrast in the Basic
Picture menu
COLOR
COLOR
The video embedded in my PowerPoint
presentation does not play on the screen
A
Correct image
If your computer is using the projector's DisplayLink
connector, see the DisplayLink User's Guide for video
troubleshooting information.
Embedded video plays correctly
A
Turn off the internal LCD display on your laptop
A
A
B
B
19
B
Problem
Solution
Result
Lamp won’t turn on, Temperature light is on Make sure vents aren’t blocked, turn off the projector
and allow it to cool for one minute
Temperature light
Lamp turns on
Startup
Screen
A
“Replace lamp” message appears at
Lamp must be replaced (see page 34)
startup, lamp won’t turn on, Lamp light is
turned on
Lamp light
loosen screws
Lamp turns on
Startup
Screen
A
loosen screws
20
Still need assistance?
If you need assistance, visit our website at www.infocus.com/service or call
us. Check out our HOW TO section there for additional information on
using this projector for home theater or gaming applications. See the Quick
Start Poster/Booklet for support contact information.
This product is backed by a limited warranty. An extended warranty plan
may be purchased from your dealer. When sending the projector in for
repair, we recommend shipping the unit in its original packing material, or
having a professional packaging company pack the unit. Please insure your
shipment for its full value.
21
Using the remote control
The remote uses two (2) provided AA batteries. They are easily installed by
removing the cover from the remote’s back, aligning the + and - ends of the
batteries, sliding them into place, and then replacing the cover.
Caution: When replacing the batteries, be aware that using batteries other
than the type provided with the projector may risk severe damage to the
remote. When disposing of the batteries, be sure to do so in an
environmentally proper manner.
navigation
buttons
To operate, point the remote at the front of the projector (not at the
computer). The range of optimum operation is about 15 feet (4.5m).
Press the remote’s Power button to turn the projector on and off (see
page 14 for shutdown info).
Press the remote’s Menu button to open the projector’s menu system. Use
the arrow buttons to navigate, and the Select button to select features and
adjust values in the menus. See page 27 for more info on the menus.
The remote also has a Source button to switch between sources.
The remote also has:
•
•
Volume buttons to adjust the sound.
Custom button that can be assigned to a special function, like Blank
Screen or Freeze (see page 30).
• Source button to switch between sources.
• Blank button to blank the screen.
• Presets button to select stored settings (see page 28).
• Mute button to silence the audio.
• Auto Image button to resynch the projector to the source
• Resize button to switch among aspect ratios (see page 28).
Troubleshooting the remote
• Make sure the batteries are installed in the proper orientation and are
not dead.
• Make sure you’re pointing the remote at the projector or the screen, not
the computer, and are within the remote range of 15 feet (4.5m). For
best results, point the remote at the projector.
22
Using the audio
connect audio cable
Using the projector’s speaker
To use the projector's speaker, connect the audio source to the projector's
Audio In connector.
To adjust the volume, press the Volume buttons on the keypad or remote.
Troubleshooting Audio
If you aren’t hearing the audio, check the following:
•
Make sure the volume is turned up enough. Press the Volume button
on the keypad or remote.
•
Make sure the correct source is active.
•
Make sure that you are connected to an “audio out” connector on the
source as opposed to a “line-in” or “microphone” connector.
•
Adjust the audio source.
•
If playing a video, make sure the playback has not been paused.
adjust volume
23
Using the keypad buttons
Most buttons are described in detail in other sections, but here is an
overview of their functions:
Power–turns the projector on and off (page 10).
Auto Image–resets the projector to the source.
Presets–cycles through the available preset settings (page 28).
Keystone–adjusts squareness of the image (page 11).
Menu–opens the on-screen menus (page 27).
menu navigation
buttons
Select–confirms choices made in the menus (page 27).
Up/Down arrows–navigates to and adjusts settings in the menus (page 27).
Volume–adjusts sound (page 23).
Source–changes the active source (page 10).
24
Optimizing computer images
Presentation features
After your computer is connected properly and the computer’s image is on
the screen, you can optimize the image using the onscreen menus. For
general information on using the menus, see page 27.
Several features are provided to make giving presentations easier. Here is
an overview, details are found in the menu section.
•
Adjust the Keystone, Contrast, or Brightness in the Basic Picture menu
(page 28).
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 28).
•
Adjust the Color Temperature in the Advanced Picture menu
(page 28).
•
Adjust the Phase, Tracking, or Horizontal or Vertical position in the
Advanced Picture menu (page 29).
•
Once you have optimized the image for a particular source, you can
save the settings using Presets. This allows you to quickly recall these
settings later (page 28).
•
If your computer is using the projector's DisplayLink connector, see the
InFocus DisplayLink Manager User's Guide for information about
optimizing images.
25
•
The Custom key allows you to assign various features to the button.
The default effect is Source Info, which displays information about the
projector and current source. See page 30 for details.
•
The Search Screen option lets you change the appearance of the blank
screen and start up screen (page 31).
•
Two options, Auto Off and Screen Save Time, are provided to
automatically shut down the projector after several minutes of
inactivity or display a black screen. This helps preserve lamp life
(page 30).
Optimizing video images
Customizing the projector
After your video device is connected properly and the image is on the
screen, you can optimize the image using the onscreen menus. For general
information on using the menus, see page 27.
You can customize the projector for your specific setup and needs. See
page 30 to page 31 for details on these features.
•
Adjust the Keystone, Contrast, Brightness, Color, or Tint in the Basic
Picture menu (page 28).
•
For rear projection, turn Rear Project on in the Setup menu.
•
•
Change the Aspect Ratio. Choose the option that best fits your input
source (page 28).
Specify which source the projector checks first for active video during
power-up.
•
Specify the function of the Custom key on the remote.
•
Turn the projector’s display messages on and off.
•
Select a Sharpness setting (page 28).
•
Adjust the Color Temperature. Select a listed warmth value (page 29).
•
Turn on Overscan to remove noise on the edges of the image (page 29).
•
Turn on power saving features.
•
Specify appearance of blank screen and startup screen.
•
Specify the language viewed on the menus.
•
Save settings for the active source as a preset.
Dynamic Messaging
You can use Command Line Interface (CLI) commands to display text
messages on the projector (for example, to display urgent alert messages to
employees). This requires a connection to the projector’s RS-232 serial
control connector. Go to our support website to download the RS-232
command reference for your projector.
26
Using the menus
To open the menus, press the Menu button on the keypad or remote. (The
menus automatically close after 60 seconds if no buttons are pressed.) Use
the arrow buttons to move up and down to highlight the desired menu,
then press the Select button.
keypad navigation
buttons
To change a menu setting, highlight it, press Select, then use the up and
down arrow buttons to adjust the value or select an option or turn the
feature on or off. Press Select to confirm your changes. Use the arrows to
navigate to another setting. When your adjustments are complete, press
Menu to access a different menu; press the Menu button at any time to
navigate to the higher-level menu and ultimately close the menus.
The menus are grouped by usage:
•
The Basic Picture menu provides common image adjustments.
•
The Advanced Picture menu provides more complex image
adjustments.
•
The Setup menu provides set-up type adjustments that are not changed
often.
•
The Status and Service menu provides information about the projector
and source.
27
Basic Picture menu
Advanced Picture menu
Setup menu
Status and Service menu
Basic Picture menu
To adjust the following settings, highlight the setting, press Select, use the
up and down arrows to adjust the values, then press Select to confirm the
changes.
Brightness: changes the intensity of the image.
Contrast: controls the degree of difference between the lightest and darkest
parts of the picture and changes the amount of black and white in the
image.
Sharpness: (video sources only) changes the clarity of the edges of a video
image. Select a sharpness setting.
Basic Picture menu
Color: adjusts a video image from black and white to fully saturated color.
The color setting applies to video sources only.
Tint: adjusts the red-green color balance in the image of NTSC video
images. The tint setting applies to NTSC video sources only.
Aspect Ratio: Aspect ratio is the ratio of the image width to image height.
TV screens are usually 4:3. HDTV and most DVDs are 16:9.
Select Auto to have the projector choose the ratio. Choose Native to see the
unmodified input with no resizing by the projector.
Select 16:9 to watch enhanced widescreen DVDs.
For more information regarding Aspect Ratio, see page 12.
Apply Preset...: Presets are provided that optimize the projector for
displaying computer presentations and video images under certain
conditions.
Aspect ratio
There is also a user-definable preset. To set this preset, adjust the image and
select Save User in the Presets menu. You can recall these settings in the
future by selecting the User preset.
Digital Zoom: changes the size of projector’s display area. If the display
area has been resized by this setting, it can be moved by changing the Horz
Shift and Vert Shift settings.
Horz Shift/Vert Shift: moves the display area horizontally or vertically if
its size has been changed by the Digital Zoom setting.
Keystone: adjusts the image vertically and makes a squarer image. You can
also adjust keystone from the keypad.
increasing keystone
28
decreasing keystone
Advanced Picture menu
BrilliantColor™: produces an expanded on-screen color spectrum that
delivers enhanced color saturation for bright, true-to-life images. Choose
Normal Look for most video sources and Bright Look for most computer
sources.
White Peaking: (video sources only) increases the brightness of whites that
are near 100%.
Color Temperature: changes the intensity of the colors. Select a listed
relative warmth value.
Force wide: This feature is to help with image-locking problems when the
correct mode cannot be determined. If this feature is off and the exact
resolution mode cannot be determined, the analog locking algorithms will
use a 4:3 mode for the image. If this feature is on and the exact mode cannot
be determined, the analog locking algorithms choose the best-matched wide
mode (either 16:9 or 16:10) for the image.
Advanced Picture menu
Overscan: removes noise around the video image.
Phase: adjusts the horizontal phase of a computer source.
Sync Threshold: (progressive signals only) If a hardware device, such as a
DVD player, is not syncing properly with the projector, select this option to
help it to sync when connected to the projector.
Tracking: adjusts the vertical scan of a computer source.
Color Space: This option applies to computer and component video
sources. It allows you to select a color space that has been specifically tuned
for the input signal. When Auto is selected, the projector automatically
determines the standard. To choose a different setting, turn off Auto, then
choose RGB for computer sources or choose either REC709 or REC601 for
component video sources.
Gamma: select the appropriate gamma from among Video, Film, Bright,
and CRT.
Horizontal/Vertical Position: adjusts the position of a computer source.
29
Setup menu
Power Sounds: controls whether the projector makes a sound when
powered on and off.
Language: allows you to select a language for the onscreen display.
Auto Source: when this feature is On, the projector automatically finds the
active source, checking the selected Power-up Source first. When this
feature is Off, the projector defaults to the source selected in Power-up
Source. To display another source, you must manually select one by
pressing the Source button on the remote or keypad.
Custom Key: allows you to assign a different function to the Custom
button, allowing you to quickly and easily use the effect. Highlight an effect
and press Select to choose a different one.
•
Source Info: the default action. Shows the Source Info menu.
•
Projector Info: Shows the Projector Info menu.
•
Aspect Ratio: toggles among 4:3, 16:9, and Native (see page 12 and
page 28).
•
Auto Image: resets the projector to the source (page 24).
•
Overscan: removes noise around the image.
•
Blank Screen: displays an empty screen.
•
Freeze Screen: pauses the projected image.
•
Mute: turns off all sound.
•
Source: cycles through available sources.
Setup menu
Blank Key: Select what to display when the blank key on the remote is
depressed: your custom snapshot, a solid color screen (blue, black or white),
the factory logo screen, a timer, or test patterns. The timer option is useful
for classroom tests or break times during meetings.
Power-up Source: determines which source the projector checks first for
active video during power-up.
Video Standard: when this feature is set to Auto, the projector attempts to
automatically pick the video standard based on the input signal it receives.
(The video standard options may vary depending on your region of the
world.) If the projector is unable to detect the correct standard, the colors
may not look right or the image may appear “torn.” If this happens,
manually select a video standard by selecting NTSC, PAL, or SECAM from
the Video Standard menu.
AC Power On: when this feature is on, the projector automatically turns on
when electrical power is connected.
Auto Off Time: automatically turns the projector off after no signals are
detected for a preset number of minutes. If an active signal is received
before the projector powers down, the image will be displayed.
Screen Save Time: automatically blanks the screen with a black color after
no signals are detected for a preset number of minutes. The image returns
when an active source is detected or a remote or keypad button is pressed.
Closed Captions: controls closed caption display while audio is not muted.
If this setting is not off, and audio is not muted, and the source is NTSC and
contains captions on the selected channel, then the projector must display
caption text overlaid on the image.
Lamp Low Power: toggles between on and off. Turn it on to lower the light
output of the lamp. This also lowers the fan speed, making the projector
quieter.
30
Rear Project: reverses the image so you can project from behind a
translucent screen.
keypad to enter the correct button press sequence. See the description above
for instructions.
Auto Keystone: automatically adjusts vertical image.
To change the PIN:
Prevent PC Screen Saver: prevents your computer from going into Screen
Save mode. The projector must be connected to the PC via a USB cable for
this feature to work.
Select “Change PIN...” in the Setup menu. Enter the existing PIN. Enter the
new PIN. You can navigate between OK and Cancel by pressing the up and
down buttons on the keypad. Select OK or Cancel by pressing the Select
button. Verify the new PIN.
Search Screen: allows you to display a blank screen instead of the default
screen at startup, and when no source is detected.
If you lose or forget your custom PIN:
Show Messages: displays status messages (such as “Searching”) in the
lower-left corner of the screen.
Contact InFocus support. Go to www.infocus.com/support
Menu Offset: allows you to change the position of the On Screen Display
items.
Menu Transparency: allows you to change how much of the projected
image behind the menu you can see. As the value increases, more of the
image behind the menu is visible.
Magnify Controls: determines whether the select key can be used to change
magnify settings when the OSD menu is not visible.
PIN Protect: the PIN (personal identification number) feature allows you
to password protect your projector. Once you enable the PIN feature, you
must enter the PIN before you can project an image. The default PIN on this
projector is Menu-Up-Down-Select-Source. Use the navigation buttons on
the remote or keypad to enter the correct 5-button press sequence. When all
5 numbers are entered correctly, press the Select button on the remote or
keypad to select OK. If the message “Wrong PIN” appears, verify the code
and re-enter it. If you mis-enter a number, you must enter 5 numbers and
press the Select button in order to access the “Wrong PIN” message and reenter the code.
To enter the PIN at projector startup:
Power up the projector. The “Enter PIN” dialog box appears after the
startup screen. Enter the PIN. Use the navigation buttons on the remote or
31
Status and Service menu
Source Info: a read-only display of current source settings.
Projector Info: a read-only display of current projector settings.
Reset Lamp Hours: resets the lamp hours used counter in the Projector Info
menu to zero. Do this only after changing the lamp.
Factory Reset: restores all settings to their default.
Service Code: only used by authorized service personnel.
Status and Service menu
32
Maintenance
Cleaning the lens
1 Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
• Avoid using an excessive amount of cleaner, and don’t apply the
cleaner directly to the lens. Abrasive cleaners, solvents or other harsh
chemicals might scratch the lens.
2 Lightly wipe the cleaning cloth over the lens in a circular motion.
security
lock
Using the security lock
The projector has a security lock for use with a PC Guardian Cable Lock
System. Refer to the information that came with the lock for instructions on
how to use it.
33
Replacing the projection lamp
The lamp hours used timer in the Projector Info menu counts the number of
hours the lamp has been in use. Twenty hours before the lamp life expires,
the message “Change lamp” appears on the screen at startup.
•
NOTE: You can order new lamps from www.infocus.com (in select
areas), your retailer or your dealer. Only genuine InFocus lamps are
tested for use in this projector. InFocus is not liable for the
performance, safety or certification of any other lamps. The use of other
lamps violates the projector warranty and voids all certification marks
on this projector.
Lamp hours
1 Turn off the projector and unplug the power cord.
2 Wait 60 minutes to allow the projector to cool thoroughly.
3 Turn the projector upside down on a soft cloth so that the lamp door is
facing you.
turn off and unplug
projector
WARNINGS:
•
To avoid burns, allow the projector to cool for at least 60 minutes before
you replace the lamp.
•
Only genuine InFocus lamps are tested with this projector. Use of other
lamps may cause electrical shock and fire.
•
Unplug the power cord before replacing the lamp.
•
Do not drop the lamp module. The glass may shatter and cause injury.
•
Do not touch the glass lamp screen. Fingerprints can obscure projection
sharpness.
wait 60 minutes
34
•
Be extremely careful when removing the lamp housing. In the unlikely
event that the lamp ruptures, small glass fragments may be generated.
The lamp module is designed to contain most of these fragments, but
use caution when removing it. Before replacing a ruptured lamp, clean
the lamp compartment and dispose of cleaning materials. Wash hands
after lamp replacement.
Hg – Lamp contains mercury. Manage in accordance with local
disposal laws. See www.lamprecycle.org.
loosen screw
4 Loosen the two captive screws on the lamp door and lift the door off.
5 Loosen the two captive screws that attach the lamp housing to the
projector.
6 Carefully remove the lamp housing. Dispose of the lamp in an
environmentally proper manner.
7 Install the new lamp housing and tighten the screws.
8 Replace the lamp door.
9 Plug in the power cord and press the Power button to turn the projector
loosen screw
back on.
10 To reset the lamp hour timer, navigate to the Status and Service menu
and select Reset Lamp Hours. See page 32 for details.
35
INDEX
Horizontal 29
Numerics
image
optimization 25
size 5
I
16x9 vs 4x3 12
A
K
Advanced menu 29
Aspect Ratio 12, 28, 30
keypad buttons 24
keystone 28
keystone, adjusting 11
B
Blank Key 30
Blank Screen 30
Brightness 28
BrilliantColor 29
L
lamp hours, resetting 35
Language 30
laptop video port activation 10
LEDs 14
leveling foot 11
C
cable box 12
cleaning the lens 33
Color 28
Color Space 29
Color Temperature 29
Computer In connector 9
connecting
computer 9
video device 12
connector panel 4
connectors on projector 7
contacting InFocus 21
Contrast 28
Custom key 25, 30
customer service contact information 21
customizing the projector 26
M
maintaining the projector 33
Menu button 27
menu usage 27
O
optimizing images 25
optimizing video 26
Overscan 29
P
PC Screen Saver Off 31
Phase 29
Picture menu 28
positioning the projector 5
Power connector 9
power cord 9
Power Save 30
Power-up Source 30
presentation features 25
projection distance 5
projector
connecting computers 9
D
DVDs 28
F
Factory Reset 32
focus 11
H
HDTV 6, 28
36
R
connecting video devices 12
connector panel 4
customization 26
image size 5
keypad buttons 24
language 30
maintenance 33
menus 27
offset 5
positioning 5
registering 3
reset 32
safety considerations 2
security lock 33
setting up 5
shutting down 14
Status Indicator Panel 14
troubleshooting problems 14
Tint 28
Tracking 29
troubleshooting 14
TV tuner 12
U
USB 9
V
Vertical 29
video devices, connecting 13
video optimizing 26
Video Standard 30
Volume button 23
W
warranty 21
Z
zoom 11
Rear 30
registering your projector 3
remote control 22
resetting the projector 32
S
Screen Aspect 12
Screen Save 14, 30
security lock 33
Service 32
Service Code 32
Settings menu 30
sharpness 28
shutting down the projector 14
Sources 30
Status Indicator Panel 14
S-video connector 13
T
37
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement