JVC | KS-FX201 | User's Manual | JVC KS-FX201 User's Manual

KS-FX201
ENGLISH
CASSETTE RECEIVER
!"#$
KS-FX201
‰∑¬
KS-FX201
«‘∑¬ÿ‡§√◊ËÕ߇≈Ëπ‡∑ª
For installation and connections, refer to the separate manual.
!"#$%&'()*+,-./0
°√ÿ≥“¥Ÿ§ŸË¡◊Õ∑’Ë·¬°µË“ßÀ“° „π°“√µ‘¥µ—Èß·≈–°“√‡™◊ËÕ¡µËÕ
INSTRUCTIONS
!"
§”·π–π”
GET0023-001A
[U]
00COVER.KS-FX201[U]f
3
11/6/00, 6:07 AM
ENGLISH
Thank you for purchasing a JVC product. Please read all instructions carefully before operation, to
ensure your complete understanding and to obtain the best possible performance from the unit.
CONTENTS
BASIC OPERATIONS .................................................... 3
RADIO OPERATIONS ................................................... 4
Listening to the radio ..................................................................... 4
Storing stations in memory ............................................................ 5
FM station automatic preset: SSM .............................................. 5
Manual preset .............................................................................. 6
Tuning into a preset station ........................................................... 7
Other convenient tuner functions ................................................. 8
Scanning broadcast stations ....................................................... 8
Selecting FM reception sound ..................................................... 8
TAPE OPERATIONS ..................................................... 9
Listening to a tape .......................................................................... 9
SOUND ADJUSTMENTS ............................................. 10
Turning on/off the loudness function .......................................... 10
Selecting preset sound modes ...................................................... 10
Adjusting the sound ...................................................................... 11
Storing your own sound adjustments ......................................... 12
OTHER MAIN FUNCTIONS ......................................... 13
Setting the clock ............................................................................ 13
Detaching the control panel ......................................................... 14
CD CHANGER OPERATIONS ...................................... 15
Playing CDs ................................................................................... 15
Selecting CD playback modes ..................................................... 17
MAINTENANCE ........................................................ 18
To extend the lifetime of the unit ................................................. 18
How to reset your unit .................................................................. 18
TROUBLESHOOTING ................................................. 19
SPECIFICATIONS ....................................................... 20
BEFORE USE
* For safety....
• Do not raise the volume level too much, as this
will block outside sounds, making driving
dangerous.
• Stop the car before performing any complicated
operations.
* Temperature inside the car....
If you have parked the car for a long time in hot
or cold weather, wait until the temperature in the
car becomes normal before operating the unit.
2
EN02-03.KS-FX201[U]f
2
11/2/00, 2:20 PM
ENGLISH
BASIC OPERATIONS
1
2
Note:
When you use this unit for the
first time, set the built-in
clock correctly, see page 13.
3
1
Turn on the power.
/I/ATT
Notes on One-Touch Operation:
• When you select tuner as a source in step 2 below, the power automatically
comes on. You do not have to press this button to turn on the power.
• If the cassette is already in the cassette compartment, tape play starts
automatically. However, it is not recommended to leave the cassette in the
compartment when turning off the power or ignition key. It may damage the
tape head and the cassette.
2
FM
Play the source.
AM
To operate the tuner, see pages 4 – 8.
To operate the tape deck, see page 9.
To operate the CD changer, see pages 15 – 17.
CD-CH
3
Adjust the volume.
Volume level appears
4
Adjust the sound as you want (see pages 10 – 12).
To drop the volume in a moment
Press
briefly while listening to any source. “ATT” starts flashing on the display, and
the volume level will drop in a moment.
To resume the previous volume level, press the button briefly again.
To turn off the power
Press
for more than 1 second.
3
EN02-03.KS-FX201[U]f
3
11/2/00, 2:20 PM
RADIO OPERATIONS
ENGLISH
Listening to the radio
1
3
1
/I/ATT
2
Turn on the power.
Note on One-Touch Operation:
When you select a band in step 2 below, the power automatically comes on. You
do not have to press this button to turn on the power.
2
FM
FM1
FM2
FM3
AM
AM
Select the band (FM1, FM2, FM3
or AM).
You can select any one of FM1, FM2, and
FM3 to listen to an FM station.
Note:
When a cassette is in the cassette compartment, you cannot select the tuner. Be sure
to eject the cassette from the cassette compartment to listen to the radio.
3
To search stations
of higher
frequencies.
Start searching a station.
When a station is received, searching stops.
To search stations
of lower
frequencies.
To stop searching before a station is received, press the same button you have pressed
for searching.
To tune in a particular frequency manually:
4
1 Press FM or AM to select the band.
2 Press and hold
T or S
until “M” starts flashing on the display.
Now you can manually change the frequency while “M” is flashing.
T or S
repeatedly until the frequency you want is reached.
3 Press
• If you hold down the button, the frequency keeps changing until you release the button.
EN04-08.KS-FX201[U]f
4
11/2/00, 2:26 PM
ENGLISH
Storing stations in memory
You can use one of the following two methods to store broadcasting stations in memory.
• Automatic preset of FM stations: SSM (Strong-station Sequential Memory)
• Manual preset of both FM and AM stations.
FM station automatic preset: SSM
You can preset 6 local FM stations in each FM band (FM1, FM2 and FM3).
2
1
1
FM1
FM
FM2
FM3
Select the FM band number (FM1, FM2 or
FM3) you want to store FM stations into.
2
Press and hold the button for more than 2
seconds.
“SSM” appears, then disappears when automatic
preset is over.
Local FM stations with the strongest signals are searched and stored automatically in the
band number you have selected (FM1, FM2 or FM3). These stations are preset in the number
buttons — No. 1 (lowest frequency) to No. 6 (highest frequency).
When automatic preset is over, the station stored in number button 1 will be automatically
tuned in.
5
EN04-08.KS-FX201[U]f
5
11/2/00, 2:26 PM
ENGLISH
Manual preset
You can preset up to 6 stations in each band (FM1, FM2, FM3 and AM) manually.
Example: Storing an FM station of 88.3 MHz into the preset number 1 of the FM1 band.
2
1
FM
3
1
Select the FM1 band.
2
Tune into a station of 88.3 MHz.
See page 4 to tune into a station.
3
Press and hold the button for more than 2
seconds.
Preset number “P1” flashes for a while.
4
Repeat the above procedure to store other stations into other
preset numbers.
Notes:
• A previously preset station is erased when a new station is stored in the same preset number.
• Preset stations are erased when the power supply to the memory circuit is interrupted (for example,
during battery replacement). If this occurs, preset the stations again.
6
EN04-08.KS-FX201[U]f
6
11/2/00, 2:26 PM
ENGLISH
Tuning into a preset station
You can easily tune into a preset station.
Remember that you must store stations first. If you have not stored them yet, see page 5 or 6.
2
1
FM
1
FM1
FM2
FM3
AM
AM
Select the band (FM1, FM2, FM3 or AM) you
want.
2
Select the number (1 – 6) for the preset station
you want.
7
EN04-08.KS-FX201[U]f
7
11/2/00, 2:26 PM
ENGLISH
Other convenient tuner functions
MO/RND
RPT/SCAN
Scanning broadcast stations
When you press RPT/SCAN while listening to the radio, station scanning starts. Each time a
broadcast is tuned in, scanning stops for about 5 seconds (tuned frequency number flashes
on the display), and you can check what program is now being broadcast.
If you want to listen to that program, press the same button again to stop scanning.
Selecting FM reception sound
When an FM stereo broadcast is hard to receive:
Press MO/RND while listening to an FM stereo broadcast. The sound you hear becomes
monaural but reception will be improved.
Lights when receiving an FM broadcast in stereo
\
To restore the stereo effect, press the same button again.
8
EN04-08.KS-FX201[U]f
8
11/2/00, 2:26 PM
ENGLISH
TAPE OPERATIONS
Listening to a tape
2
3
1
1
Turn on the power.
/I/ATT
2
Insert a cassette.
When one side of the tape reaches its end during play, the
other side of the tape automatically starts playing. (Auto
Reverse)
3
Select the tape direction.
• Press the both buttons at the same time.
Each time you press the button, the tape direction changes
) and reverse (
).
alternatively – forward (
PROG
To stop play and eject the cassette
Press 0.
Tape play stops and the cassette ejects from the cassette compartment.
You can hear the last received station.
• You can also eject the cassette with the unit turned off.
To fast-wind a tape
Press either ¡ or 1.
The tape will be wound in the direction of the arrows
(¡ or 1).
To restart playback, press ¡ or 1 lightly.
Tape direction
9
EN09.KS-FX201[U]f
9
11/2/00, 2:24 PM
ENGLISH
SOUND ADJUSTMENTS
Turning on/off the loudness function
The human ear is less sensitive to low and high frequencies at low volumes.
The loudness function can boost these frequencies to produce a well-balanced sound at low
volume levels.
Each time you press LOUD, the loudness function turns on/off alternatively.
LOUD
|\
Selecting preset sound modes
You can select a preset sound adjustment suitable to the music genre.
Each time you press SOUND, the sound mode changes as follows.
SOUND
Indication
For:
Preset values
Bass
Treble
Loudness
SCM OFF
(Flat sound)
00
00
On
BEAT
Rock or disco music
+2
00
On
POP
Light music
+4
+1
Off
SOFT
Quiet background music
+1
–3
Off
Notes:
• You can adjust the preset sound mode to your preference, and store it in memory.
If you want to adjust and store your original sound mode, see “Storing your own sound adjustments”
on page 12.
• To adjust only the bass and treble reinforcement levels to your preference, see “Adjusting the sound”
on page 11.
• When one of the sound modes is selected, it is shown on the display as follows:
For example, when “POP” is selected.
10
EN10-12.KS-FX201[U]f
10
11/6/00, 9:02 AM
ENGLISH
Adjusting the sound
You can adjust the treble/bass sound and the speaker balance.
2
1
1
Select the item you want to adjust.
Indication
To do:
Range
BAS
(bass)
Adjust the bass
–6 (min.) — +6 (max.)
TRE
(treble)
Adjust the treble
–6 (min.) — +6 (max.)
FAD
(Fader)*
Adjust the front and rear speaker
balance
R6 (rear only) — F6 (front only)
BAL
(Balance)
Adjust the left and right speaker
balance
L6 (left only) — R6 (right only)
VOL
(Volume)
Adjust the volume
00 (min.) — 50 (max.)
Note:
* If you are using a two-speaker system, set the fader level to “00”.
2
Adjust the level.
Note:
Normally the + and – buttons work as the volume control buttons.
So you do not have to select “VOL” to adjust the volume level.
11
EN10-12.KS-FX201[U]f
11
11/6/00, 9:02 AM
ENGLISH
Storing your own sound adjustments
You can adjust the sound modes (BEAT, POP, SOFT: see page 10) to your preference and
store your own adjustments in memory.
3
1
2
2
1,4
SOUND
Call up the sound mode you want to adjust.
See page 10 for details.
Within
5 seconds
2
To adjust the bass or treble sound level
Select “BAS” or “TRE.”
LOUD
To turn on or off the loudness function
Each time you press LOUD, the loudness function turns on
and off alternatively. (= go to step 4)
Within
5 seconds
3
Adjust the bass or treble level.
See page 11 for details.
Within
5 seconds
4
Press and hold SOUND until the sound mode
you have selected in step 1 flashes on the
display.
SOUND
Your setting is stored in memory.
5
Repeat the same procedure to store other settings.
To reset to the factory settings
Repeat the same procedure and reassign the preset values listed in the table on page 10.
12
EN10-12.KS-FX201[U]f
12
11/6/00, 9:02 AM
ENGLISH
OTHER MAIN FUNCTIONS
Setting the clock
2,3
1,4 2,3
1
DISP
4
Press and hold the button for more than 2
seconds.
“CLOCK H” or “CLOCK M” appears on the display.
2
1.
Set the hour.
1. Select “CLOCK H” if not shown on the
display.
2.
2. Adjust the hour.
3
1.
Set the minute.
1. Select “CLOCK M”.
2.
2. Adjust the minute.
4
Start the clock.
To check the current clock time (changing the display mode)
Press DISP repeatedly. Each time you press the button, the display mode changes as follows.
During tuner operation:
Frequency
During tape operation:
Clock
Play mode
Clock
During CD changer operation:
Elapsed
playing time
Disc
number
Clock
13
EN13-14.KS-FX201[U]f
13
11/2/00, 2:28 PM
ENGLISH
Detaching the control panel
You can detach the control panel when leaving the car.
When detaching or attaching the control panel, be careful not to damage the connectors on
the back of the control panel and on the panel holder.
How to detach the control
panel
Before detaching the control panel, be sure
to turn off the power.
1
2
3
How to attach the control
panel
1
Unlock the control panel.
2
Lift and pull the control panel
out of the unit.
Put the detached control
panel into the provided case.
Insert the left side of the
control panel into the groove
on the panel holder.
Press the right side of the
control panel to fix it to the
panel holder.
Note on cleaning the connectors:
If you frequently detach the control panel, the
connectors will deteriorate.
To minimize this possibility, periodically wipe
the connectors with a cotton swab or cloth
moistened with alcohol, being careful not to
damage the connectors.
Connectors
14
EN13-14.KS-FX201[U]f
14
11/2/00, 2:28 PM
CD CHANGER OPERATIONS
ENGLISH
We recommend that you use one of the CH-X series with your unit.
If you have another CD automatic changer, consult your JVC car audio dealer for connections.
• For example, if your CD automatic changer is one of the KD-MK series, you need a cord (KS-U15K)
for connecting it to this unit.
Before operating your CD automatic changer:
• Refer also to the Instructions supplied with your CD changer.
• If no discs are in the magazine of the CD changer or the discs are inserted upside
down, “NO CD” or “NO DISC” will appear on the display. If this happens, remove the
magazine and set the discs correctly.
• If “RESET 1 - RESET 8” appears on the display, something is wrong with the connection
between this unit and the CD changer. If this happens, check the connection, connect
the connecting cord(s) firmly if necessary, then press the reset button of the CD changer.
Playing CDs
¢
4
1
Number buttons
1
Select the CD automatic changer.
CD-CH
Playback starts from the first track of the first disc.
All tracks of all discs are played back.
Disc number
\
Track number
Elapsed playing time
(The clock time is shown if you have
pressed DISP to see the clock time.
See page 13.)
Note on One-Touch Operation:
When you press CD-CH, the power automatically comes on. You do not have to press
to turn on the power.
15
EN15-17.KS-FX201[U]f
15
11/2/00, 2:29 PM
ENGLISH
To fast forward or reverse the track
¢, while playing a CD, to fast forward the track.
Press and hold
Press and hold 4
, while playing a CD, to reverse the track.
To go to the next track or the previous track
Press
¢ briefly, while playing a CD, to go ahead to the beginning
of the next track. Each time you press the button consecutively, the
beginning of the next tracks is located and played back.
briefly, while playing a CD, to go back to the beginning
Press 4
of the current track. Each time you press the button consecutively, the
beginning of the previous tracks is located and played back.
To go to a particular disc directly
7
8
9
10
11
12
Press the number button corresponding to the disc number to start its
playback.
• To select a disc number from 1 – 6:
Press 1 (7) – 6 (12) briefly.
• To select a disc number from 7 – 12:
Press and hold 1 (7) – 6 (12) for more than 1 second.
Ex. When disc number 3 is selected
Disc number
Track number
16
EN15-17.KS-FX201[U]f
16
11/2/00, 2:29 PM
ENGLISH
Selecting CD playback modes
MO/RND
RPT/SCAN
To play back tracks at random (Random Play)
MO/RND
Mode
Each time you press MO/RND (Mono/Random) while playing a CD, CD
random play mode changes as follows:
RND1
RND2
(Random1)
(Random2)
RND Indicator
Canceled
Plays at random
RND1
Lights
All tracks of the current disc, then the tracks of the
next disc, and so on.
RND2
Flashes
All tracks of all discs inserted in the magazine.
To play back tracks repeatedly (Repeat Play)
RPT
SCAN
Mode
Each time you press RPT/SCAN (Repeat/Scan) while playing a CD, CD
repeat play mode changes as follows:
RPT1
RPT2
(Repeat1)
(Repeat2)
RPT Indicator
Canceled
Plays repeatedly
RPT1
Lights
The current track (or specified track).
RPT2
Flashes
All tracks of the current disc (or specified disc).
17
EN15-17.KS-FX201[U]f
17
11/2/00, 2:29 PM
ENGLISH
MAINTENANCE
To extend the lifetime of the unit
This unit requires very little attention, but you will be able to extend the life of the unit if you
follow the instructions below.
To clean the heads
• Clean the heads after every 10 hours of use
using a wet-type head cleaning tape (available
at an audio store).
When the head becomes dirty, you may realize
the following symptoms:
– Sound quality is reduced.
– Sound level decreases.
– Sound drops out.
• Do not play dirty or dusty tapes.
• Do not touch the highly-polished head with any
metallic or magnetic tools.
To keep the tape clean
• Always store the tapes to their storage cases
after use.
• Do not store tapes in the following places:
– Subject to direct sunlight
– With high humidity
– At extremely hot temperatures
CAUTIONS:
• Do not play the tapes with peeling labels; otherwise, they can damage the unit.
• Tighten tapes to remove slack since loose tape may become entangled with the mechanism.
• Do not leave a cassette in the cassette compartment after use, as the tape may become slack.
How to reset your unit
Press and hold both the SEL (Select) and
(Standby/On/ATT) buttons at the
same time for several seconds.
This will reset the built-in microcomputer.
NOTE: Your preset adjustments — such as preset channels or sound adjustments
— will also be erased.
(Standby/On/ATT)
SEL (Select)
18
EN18-20.KS-FX201[U]f
18
11/2/00, 2:30 PM
TROUBLESHOOTING
Causes
Symptoms
Remedies
Insert the cassette with the
• A cassette tape cannot be
inserted.
You have tried to insert a
cassette in the wrong way.
• Cassette tapes become hot.
This is not a malfunction.
• Tape sound is at very low
level and sound quality is
degraded.
The tape head is dirty.
Clean it with a head cleaning
tape.
• Sound is sometimes
interrupted.
Connections are not good.
Check the cords and
connections.
• Sound cannot be heard from
the speakers.
The volume control is turned
to the minimum level.
Adjust it to the optimum level.
Connections are incorrect.
Check the cords and
connections.
• Static noise while listening
to the radio.
The antenna is not connected
firmly.
Connect the antenna firmly.
• “NO CD” or “NO DISC”
appears on the display.
No CD is in the magazine.
Insert CDs into the magazine.
CDs are inserted incorrectly.
Insert them correctly.
This unit is not connected to a
CD changer correctly.
Connect this unit and the CD
changer correctly and press
the reset button of the CD
changer.
• “RESET 8” appears on the
display.
• “RESET 1-RESET 7”
appears on the display.
• The unit does not work at
all.
• The CD changer does not
work at all.
ENGLISH
What appears to be trouble is not always serious. Check the following points before calling a
service center.
exposed tape facing right.
Press the reset button of the
CD changer.
The built-in microcomputer
While holding SEL, press
may function incorrectly due to
for more than 2
noise, etc.
seconds to reset the unit.
(The clock setting and preset
stations stored in memory are
erased.) (See page 18).
19
EN18-20.KS-FX201[U]f
19
11/2/00, 2:30 PM
ENGLISH
SPECIFICATIONS
AUDIO AMPLIFIER SECTION
CASSETTE DECK SECTION
Maximum Power Output:
Front: 40 watts per channel
Rear: 40 watts per channel
Continuous Power Output (RMS):
Front: 16 watts per channel into 4 Ω, 40
Hz to 20 000 Hz at no more than
0.8% total harmonic distortion.
Rear: 16 watts per channel into 4 Ω, 40
Hz to 20 000 Hz at no more than
0.8% total harmonic distortion.
Load Impedance: 4 Ω (4 Ω to 8 Ω allowance)
Tone Control Range
Bass: ±10 dB at 100 Hz
Treble:±10 dB at 10 kHz
Frequency Response: 40 Hz to 20 000 Hz
Signal-to-Noise Ratio: 70 dB
Line-Out Level/Impedence: 2.0 V/20 kΩ load
(250 nWb/m)
Output Impedance: 1 kΩ
Wow & Flutter: 0.15% (WRMS)
Fast-Wind Time: 190 sec. (C-60)
Frequency Response:
50 Hz to 14 000 Hz (±3 dB)
Signal-to-Noise Ratio: 52 dB
Stereo Separation: 40 dB
GENERAL
Power Requirement
Operating Voltage: DC 14.4 volts (11 volts to
16 volts allowance)
Grounding System: Negative ground
Allowable Working Temperature:
0°C to +40°C (32°F to 104°F)
Dimensions (W x H x D)
Installation Size: 182 mm x 52 mm x 150 mm
Panel Size: 188 mm x 58 mm x 14 mm
Mass: 1.3 kg (2.9 lbs) (excluding accessories)
Design and specifications subject to change
without notice.
TUNER SECTION
Frequency Range
FM: 87.5 MHz to 108.0 MHz
AM: 531 kHz to 1 602 kHz
[FM Tuner]
Usable Sensitivity: 11.3 dBf (1.0 µV/75 Ω)
50 dB Quieting Sensitivity:
16.3 dBf (1.8 µV/75 Ω)
Alternate Channel Selectivity (400 kHz):
65 dB
Frequency Response: 40 Hz to 15 000 Hz
Stereo Separation: 35 dB
Capture Ratio: 2.0 dB
Having TROUBLE with operation?
Please reset your unit
Refer to page of How to Reset
[AM Tuner]
Sensitivity: 20 µV
Selectivity: 35 dB
20
EN18-20.KS-FX201[U]f
20
11/2/00, 2:30 PM
KS-FX201
Installation/Connection Manual
!"#$
ØVOd²« ULOKFð VÒO²
qOu²«
V
GET0023-002A
[U]
J
• This unit is designed to operate only on 12 volts DC, NEGATIVE
ground electrical systems.
wÐdŽ
dýU³ wzUÐdN —UOð WDÝ«uÐ jI qLFO “UN'« «c¼ rLbI •
ÆVUÝ i¹—Qð WOzUÐdN WLE½« ¨Xu ±≤ ¨DC
• !"#$% 12V !"#$%&'(
!
!"#$%
INSTALLATION (IN-DASH
MOUNTING)
• The following illustration shows a typical installation. However,
you should make adjustments corresponding to your specific
car. If you have any questions or require information regarding
installation kits, consult your JVC car audio dealer or a company
supplying kits.
1
Before mounting: Press
(Control Panel Release
button) to detach the control panel.
2
3
Remove the trim plate.
!"#$%&'()*+,-%./0 123.45
!"#$%&JVC !"#$%&'()*+,
1
2
3
Remove the sleeve after disengaging the sleeve locks.
!"
!"#
!"#$%&'()&*+
1 5
Fix the mounting bolt to the rear of the unit’s body and place
the rubber cushion over the end of the bolt.
6
Do the required electrical connections explained on the back
of this instructions.
Slide the unit into the sleeve until it is locked.
!"#$
3 6
7
8
9
!"#$
!"#$%&'()*+,#-./0123
ÆÍœuLŽ qJAÐ “UN'« nË«
!"#$%&'()%*+,-./01
!"#$
%&'(
±
!"
!"
!"#$
Attach the trim plate.
Attach the control panel.
±
Ë« —d?Cð Âb?Ž s? bQ?𠨓UN?'« nO?uð b?MŽ ∫W?EŠö?
Æ“UN'« s WOHK)« WN'« w œułu*« “uOH« ·öð«
u¼ U?L? ¨w?«u?« qJ?O?N?«Ë “UN?'« 5?Ð 5?²?U?*« q?šœ«
Æw«u« qJON« U²³¦ qBH ¨qJA« w 5³
≤
Æw«u« qJON« Ÿe½«
≥
!"#$%&'()
!"#$%&&'()*+,-./0$ !"1
“d??« j??G?{« ∫V??O??d?²??« ¡b??Ð q?³??
ÆrJײ« WŠu qB qł« s ©rJײ«
≤
Æw«u« qJON« U²³¦ qB bFÐ w«u« qJON« Ÿe½« ≥
* !"#$%&'()*+,-./01-23!"45
!"#$%&'()*+
5
W?Šu?? d??¹d?% —“®
!"#$%&'()*+,-./01
4
l ÆWOU¦*« VOd²« WI¹d?Þ wU²« w×O{u²« rÝd« sO³¹
Ò
•
w?²?« …—U?O??« Ÿu?½ o?ÐU?D?ð ö?¹b?F?ð q?L?Ž p?O?K?Ž V?−¹ ¨p–
’uBÐ UuKF* WłUŠ Ë« «—UH²Ý« „UM¼ ÊU «–« ÆUNJK²9
W??O?ðu?B?« …e??N?łô« Ÿ“u? …—U??A? ²?Ý« v?łd??¹ ¨V?O?d??²?« «Ëœ«
Æ «Ëœô« …cN WŽ“u*« WdA« Ë« JVC W—U «—UOK
ÆWM¹e« WŠu Ÿe½«
2 !"#$%&'(%)*+,-./0123
!"
Install the sleeve into the dashboard.
* After the sleeve is correctly installed in the dashboard,
bend the appropriate tabs to hold the sleeve firmly in place,
as illustrated.
!"#$%&
!"#
Note: When you stand the unit, be careful not to damage
the fuse on the rear.
2 Insert the 2 handles between the unit and the sleeve, as
illustrated, to disengage the sleeve locks.
3 Remove the sleeve.
Note: Be sure to keep the handles for future use after
installing the unit.
uKÐUð ‡ qš«œ ® “UN'« VOdð
©…—UO«
• !"#$%&' ()*+,-./0123452
1 Stand the unit.
7
8
9
0800HISFLEJES
EN, CH, AR
ENGLISH
4
C
q?? ł« s?? U?? U???? *« v??K?? Ž W??E?? U??;« w?? łd??¹ ∫W?? E??Šö?? Æ“UN'« VOdð bFÐ UIŠô ‰ULF²Ýô«
Æ…—UO« uKÐUð qš«œ w«u« qJON« V—
¥
qJAÐ …—UO« uKÐUð qš«œ UOK w«u« qJON« VOdð bFÐ *
qJ?ON?« XO?³¦?² V?ÝUM? qJ?AÐ W?M?_« wM?Ł« ¨`O?×
w 5³ u¼ UL ¨`O×B« ÊUJ*« w rJ× qJAÐ w«u«
ÆqJA«
bFÐË “UN'« qJO¼ s WOHK)« WN'UÐ VOd²« —UL X³ÒŁ
Æ—UL*« W¹UN½ ‚u WOÞUD*« …uA(« l{ p–
µ
nKš ÕËdA u¼ UL WÐuKD*« WOzUÐdNJ« öOu²« qLŽ«
Æ ULOKF²« Ác¼
∂
∑
ÆWM¹e« WŠu VÒ— ∏
ÆrJײ« WŠu VÒ— π
Æ`O× qJAÐ X³¦¹ v²Š w«u« qJON« qš«œ “UN'« qšœ«
1
2
Dashboard
…—UO« uKÐUð
Mu
Mu lti
sic
Sca
n
Rubber cushion
!"
WOÞUD*« …uA(«
18
4m
m
4
Sleeve
!
5
w«u« qJON«
VOd²« —UL
3
4*
6
10
Mu
Mu lti
sic
Sc
an
2
WU*«
Trim plate
Sleeve
!
10
WM¹e« WŠu
Fuse
“uOH«
Lock plate
Slot
XO³¦²« W×OH
dOG oý
Ò
1
3
1
1
2
3
4
5
w«u« qJON«
Instal.EN.CH.AR.KS-FX201[U]
See the back page for electrical
connections.
!"#$%&'()*
qł« s WOHK)« W×HB« dE½«
ÆWOzUÐdNJ« öOu²«
9
Handle
!"
mm
Mounting bolt
!
7
8
53
3/24/05, 10:02 PM
• When installing the unit without using the sleeve
• !"#$%&'($
• When using the optional stay
• !"#
w«u« qJON« «b²Ý« ÊËbÐ “UN'« Vdð UbMŽ •
XO³¦²K wU{« bM «b²Ý« bMŽ •
In a Toyota for example, first remove the car radio and install the unit in its place.
!TOYOTA !"#$%&'()*+,-.)/012&3456
Æt½UJ w “UN'« VÒ— p– bFÐ ôË« …—UO« u¹œ«— Ÿe½« ¨Uðu¹uð Ÿu½ «—UOÝ w ¨‰U¦*« qO³Ý vKŽ
Fire wall
s W¹UL(« —«bł
o¹d(«
Stay (option)
!"
Washer
Dashboard
* Not included with this unit.
* !"#$
Æ“UN'« «c¼ l œËe
Ò
dOž*
Flat type screws (M5 x 6 mm)*
! (M5 x 6 mm)*
*©rK ∂ ™ M5® …bŽUI« W¹u² wž«dÐ
X³³¦ð bM
©wU{«®
ÂUJŠ« WIKŠ
qOu²«
Lock nut
!
…—UO« uKÐUð
Bracket*
*
*XO³¦²« WOH²
XO³¦²« WuL
Mu
Mu lti
sic
Sc
an
Screw (option)
!"
Mounting bolt
!
©wU{«® wždÐ
Flat type screws (M5 x 6 mm)*
! (M5 x 6 mm)*
Pocket
VOd²« —UL
VOł
Bracket*
*
Sleeve
!
…bŽUI« W¹u² wž«dÐ
*©rK ∂ ™ M5®
WOH²
w«u« qJON«
*XO³¦²«
Note: When installing the unit on the mounting bracket, make sure to use the 6 mm-long screws. If
longer screws are used, they could damage the unit.
!"#$%&'()*+,6mm !"#$%&' !"()*+,-#
WUŠ w ÆrK ∂ ‰uÞ wž«dÐ Âb²Ý« s bQð ¨XO³¦²« WOH² vKŽ “UN'« VOdð bMŽ ∫WEŠö
Æ“UN'« —d{ Ë« nKð V³¹ Ê« sJ1 p– ÊU ¨rK ∂ s ‰uÞ« wž«dР«b²Ý«
Removing the unit
!
• Before removing the unit, release the rear section.
• !"#$%&!"'()*+,-.(/012
1
Remove the control panel.
1
!"#$
2
Remove the trim plate.
2
3
!"#
Insert the 2 handles into the slots, as shown. Then, while gently
pulling the handles away from each other, slide out the unit.
(Be sure to keep the handles after installing it.)
1
3
…—UO« uKÐUð s “UN'« Ÿe½
ÆwHK)« ¡e'« —dŠ ¨“UN'« Ÿe½ q³ •
ÆrJײ« WŠu Ÿe½«
ÆWM¹e« WŠu Ÿe½«
!"#$%&'()*+,-."/01234$5
!"#$%&'() *+
!"#$%&'()*+,-.
Æq?J?A?« w? 5?³? u?¼ U?L? ¨‚u?I?A?« q?š«œ 5?²U*« qšœ«
sŽ …bŠ«u?« «b?O?FÐ WUDKÐ 5²U*« V×Ý ¡UMŁ« ¨p– bFÐ
Æ×U)« v« “UN'« V×Ý« ¨Èdšô«
©“UN'« VOdð bFÐ 5²U*UÐ pþUH²Š« s bQð®
±
≤
≥
3
2
Handle
!"
Mu
Mu lti
sic
Sc
an
WU*«
Parts list for installation and connection
The following parts are provided with this unit.
After checking them, please set them correctly.
!"#$%&'(
qOu²«Ë VOd²« ¡«eł« WLzU
!"#$%&'()
!"#$%&'()*
Æ“UN'« l …œËe WOU²« ¡«ełô«
Æ`O× qJAÐ rN³Odð vłd¹ ¨¡«ełô« Ác¼ h× bFÐ
Hard case
Power cord
!"#$%&
VK ‚ËbM
Lock nut (M5)
! (M5)
WOzUÐdNJ« WUD« pKÝ
©M5® XO³¦²« WuL
Trim plate
WM¹e« WŠu
Mounting bolt (M5 x 20 mm)
! (M5 x 20 mm)
Handles
!"
©rK ≤∞ ™ M5® VOd²« —UL
UU*«
Sleeve
!
Washer (ø5)
(ø5)
w«u« qJON«
ÂUJŠ« WIKŠ
©µ dD® qOu²«
Rubber cushion
!"
WOÞUD*« …uA(«
Instal.EN.CH.AR.KS-FX201[U]
2
3/24/05, 9:11 PM
ENGLISH
wÐdŽ
ELECTRICAL CONNECTIONS
!
To prevent short circuits, we recommend that you disconnect the
battery’s negative terminal and make all electrical connections
before installing the unit. If you are not sure how to install this unit
correctly, have it installed by a qualified technician.
!"#$%&'()*+,#-./0123#4567/
!"#$%&'()*$+,)-./012345678
!"#$
Note:
This unit is designed to operate only on 12 volts DC, NEGATIVE
ground electrical systems. If your vehicle does not have this
system, a voltage inverter is required, which can be purchased at
JVC car audio dealers.
• Replace the fuse with one of the specified rating. If the fuse
blows frequently, consult your JVC car audio dealer.
• If noise is a problem...
This unit incorporates a noise filter in the power circuit. However,
with some vehicles, clicking or other unwanted noise may occur.
If this happens, connect the unit’s rear ground terminal (See
connection diagram below.) to the car’s chassis using shorter
and thicker cords, such as copper braiding or gauge wire. If noise
still persists, consult your JVC car audio dealer.
• Maximum input of the speakers should be more than 40 watts at
the rear and 40 watts at the front, with an impedance of 4 to 8
ohms.
• Be sure to ground this unit to the car’s chassis.
• The heat sink becomes very hot after use. Be careful not to
touch it when removing this unit.
!"#$%12V !"#$%&' !"#$%&
!"#$%&'( )*+,$-./JVC !"#
!"
• !"#$%&'()* !+,- !./0123
JVC !"#$%&'
• !"#$
!"#$%&'()*+,-./0 12345067
!"#$%&'()*+,-./012345678
!"#$%&'()*%+,-./&012 !"
!"#$%&'( !"#$%&'()*+ JVC !"#$%&
• !"#$%&'()*%+ 40 !"#$%&'(
40 !"#$ 4 – 8 • !"#$%&'()
• !"#$%&'(%)*+#,-./#01234
!"
WOzUÐdNJ« öOu²«
Heat sink
iHš W×OH
…—«d(«
A Typical Connections / !"#$ /
WOł–uLM« öOu²«
! !"#$%&'()*+%,&-./01234
Before connecting: Check the wiring in the vehicle carefully.
Incorrect connection may cause serious damage to this unit.
1
2
3
Connect the colored leads of the power cord to the car battery,
speakers and automatic antenna (if any) in the following
sequence.
1 Black: ground
2 Yellow: to car battery (constant 12V)
3 Red: to an accessory terminal
4 Blue with white stripe: to automatic antenna (200mA
max.)
5 Others: to speakers
Connect the antenna cord.
Finally connect the wiring harness to the unit.
Left
—U¹
·d?Þ qBH?Ð wu½ ¨W?OzUÐd?NJ?« dz«Ëb« w? dOB?Ið ÀËbŠ l?M*
VO?d?ð q³? WO?zUÐd?NJ?« ö?Ou?²« q?LŽ r?Ł V?U?« W¹—U?D³?«
¨`O× qJAÐ “UN'« VOdð WOHOJÐ p²dF ÂbŽ WUŠ w Æ“UN'«
VOd² q¼RË h² hA “UN'« VOdð WOKLŽ „dð vłd¹
Æ…eNłô« Ác¼ q¦
∫WEŠö
¨DC dýU³ wzUÐdN —UOð WDÝ«uÐ qLFO “UN'« «c¼ rL bI
œułË ÂbŽ WUŠ w ÆVUÝ i¹—Qð WOzUÐdN WLE½« ¨Xu ±≤
¨ÃU²u? ‰u?×? «b?²Ý« V−¹ ¨pð—U?O?Ý w? ÂUEM« «c¼ q¦
«—U?O??K WOðu?B?« …e?Nłô« ¡öË s? ‰u?;« «c¼ ¡«d?ý s?J1Ë
ÆJVC W—U
«–« ÆW?u?u?*« U?ÝU?O?I?« f?H?½ q?L?×?¹ dšPÐ “uOH« ‰b³²Ý« •
WOðuB« …eNłô« ¡öË …—UA²Ý« vłd¹ ¨“uOH« ‚«d²Š« —dJð
ÆJVC W—U «—UOK
ÆÆÆWKJA*« u¼ ZO−C« ÊU «–« •
W?? U?? D? « …d?? z«œ q?? š«œ Z?? O? ?−? ?{ d?? ²? ?K? ? “U?? N? ?'« «c?? ¼ Âb??? ²? ? ¹
Ÿu½ Àb×¹ Ê« sJ1 ¨ «—UO« iFÐ w ¨p– l ÆWOzUÐdNJ«
q¦ ÀËb?Š WUŠ w Æ»užd?*« dOž ZO−C« Ë« WIDID« s
d?E½«® “U?N?'« W?O?HKš w œułu*« i¹—Q?²« ·d?Þ qË« ¨p–
W?? D? Ý«u??Ð …—U??O? ? « q??J? O? ¼ l?? ©q??H? Ýô« w?? q??O? u??²? « r??Ý—
Ë« ‰Ëb:« ”U×M« pKÝ q¦ ¨pLÝ«Ë dB« „öÝ« «b²Ý«
¨Z?O?−?C?« Ë« W?I?D?ID« nu?ð Âb?Ž W?U?Š w? Æw?ÝU?O?I pKÝ
ÆJVC W—U «—UOK WOðuB« …eNłô« ¡öË …—UA²Ý« vłd¹
¥∞ s? d?¦?« U?ŽU?L??« q?šb? v?B?ô« b?(« ÊuJ¹ Ê« V−¹ •
l? ¨W?O?U?ô« U?ŽU?L??K ◊«Ë ¥∞ Ë W?O?H?K?)« U?ŽU?L??K ◊«Ë
ÆÂË« ∏ v« ¥ 5Ð WF½U2
Æ…—UO« qJO¼ l “UN'« i¹—Qð s bQð •
bQð Æ«b²Ýô« bFÐ «bł WMšUÝ …—«d(« iHš W×OH `³Bð •
Æ“UN'« Ÿe½ bMŽ UN²ö ÂbŽ s
1
!"#$%&'()*+,-.%/012/34 !"#$%&' !"#
1 !"
2 !"#$%& 12V
3 !"#$%&'()*+,4 !"#$%&'()*+,- 200 5 !"#$%
2
3
!"
…—U?O??« w? „ö?Ýô« W?J?³?ý s bQð ∫q?O?u?²?U?Ð ¡b?³?« q³
Ê« s?J?1 Æ“U?N?'« q?O?u?ð W?OKLŽ w QDš Àb×¹ ô v²Š WbÐ
Æ“UN−K wIOIŠ qDŽ ‰uBŠ v« ¡vÞU)« qOu²« V³¹
l? WOzUÐd?N?J?« WUD« b¹Ëe?ð p?K W½u?K*« „öÝô« qË«
Ê«® w?J?O?ðUu?ðËô« w?z«u?N?«Ë U?ŽU?L??« ¨…—U?O??« W¹—U?D?Ð
ÆwU²« qK²« VŠ ©błË
©…—UO« qJO¼ l® ÷—ô« l ∫œuÝô« pK« ±
©Xu ±≤ XÐUŁ® …—UO« W¹—UDÐ l ∫dHô« pK« ≤
wU{ô« ·dD« l ∫dLŠô« pK« ≥
wJOðUuðËô« wz«uN« l ∫iOÐôUÐ jD<« ‚—“ô« pK« ¥
#$%&'
©dO³« wKKO ≤∞∞ vBô« b(«®
UŽUL« l ∫Èdšô« „öÝô« µ
Æwz«uN« pKÝ qË«
!"#$%&'&()*+,
≤
Æ“U?N?'« l „öÝô« qUŠ qË« ¨«d?Oš« ≥
We recommend that you connect one of the CH-X series CD changers.
• If your CD changer is one of the KD-MK series, you need an optional cord (KS-U15K).
!"#$ CH-X CD !
• !CD !KD-MK !"#$(KS-U15K)
JVC CD changer jack
JVC CD !"
ÆCH-X WKKÝ s CD W−b*« U½«uDÝô« ôb³ bŠ« qOu²Ð wu½
ÃU²% ·uÝ ¨KD-MK WKKÝ s WJK²9 Íc« CD W−b*« U½«uDÝô« ‰Òb³ ÊU «–« •
Æ©KS-U15K® wU{« pKÝ v«
W−b*« U½«uDÝô« ‰bÒ³ f³I
JVC W—U CD
Line out
(see diagram B )
!
! B JVC CD changer
JVC CD U½«uDÝô« ‰bÒ³
JVC W—U CD W−b*«
10
*
j)« Ãdš
© B jD<« dE½«®
Right
vMLO«
Antenna terminal
!
wz«uN« ·dÞ
10A fuse
10A Rear ground terminal
!"#$%
dO³« ±∞ “uO
wHK)« i¹—Q²« ·dÞ
Black
3
2
To antenna
!
œuÝ√
1
wz«uN« v«
Yellow*1
*1
¿
± dH√
1
*
qJO¼ Ë« w½bF*« r'« v«
w½bF*« …—UO«
To a live terminal in the fuse block connecting
to the car battery (bypassing the ignition switch)
!"#$%&'()*+ !"#$,
!"#$ !"#$%&'
2
Wuu*« “uOH« WŽuL− w w(« ·dD« v«
©‰UF²ýô« ÕU²H0 «—Ëd® W¹—UD³« l
3
Fuse block
!"
To an accessory terminal in the fuse block
!"#$%&'()*
“uOH« WŽuL−
Blue with white stripe
!"#$
V?−¹ ¨VOd?²« q³ “UN'« «c¼ qOGAð h× q³ ∫ ±¿
ÊËbÐ “UN'« qOGAð sJ1 ô YOŠ ¨pK« «c¼ qOuð
ÆpK« qOuð
‰UF²ýô« ÕU²H
*
To metallic body or chassis of the car
!"#$%&'
dLŠ√
Ignition switch
!
Not included with this unit.
!"#$%
Æ“UN'« «c¼ l œËe
Ò
dOž
Red
*1: Before checking the operation of this unit prior to
installation, this lead must be connected, otherwise
power cannot be turned on.
*1: !"#$%&'()*+,-.$/01234 !"#$%&'(
“uOH« WŽuL− w wU{ô« ·dD« v«
iOÐôUÐ jD ‚—“« pKÝ
4
To automatic antenna if any
!"#$%
błË Ê« wJOðUuðËô« wz«uN« v«
5
White with black stripe
!"#$
White
Gray with black stripe
!"#$
Gray
Green with black stripe
!"#$
Green Purple with black stripe
!"#$
Purple
j?D?? i?OЫ pKÝ
œuÝôUÐ
iOÐ√
œuÝôUÐ jD ÍœU—
ÍœU—
œuÝôUÐ jD dCš√
dCš« œuÝôUÐ jD w½«uł—«
w½«uł—«
Instal.EN.CH.AR.KS-FX201[U]
3
±
Left speaker (front)
! !
Right speaker (front)
! !
Left speaker (rear)
! !
Right speaker (rear)
! !
©WOUô«® ÈdO« WŽUL«
©WOUô«® vMLO« WŽUL«
©WOHK)«® ÈdO« WŽUL«
©WOHK)«® vMLO« WŽUL«
3/24/05, 9:30 PM
PRECAUTIONS on power supply and speaker
connections:
• DO NOT connect the speaker leads of the power cord to
the car battery; otherwise, the unit will be seriously
damaged.
• Connect the black lead (ground), yellow lead (to car battery,
constant 12V), and red lead (to an accessory terminal) correctly.
• BEFORE connecting the speaker leads of the power cord to
the speakers, check the speaker wiring in your car.
– If the speaker wiring in your car is as illustrated in Fig. 1
and Fig. 2 below, DO NOT connect the unit using that original
speaker wiring. If you do, the unit will be seriously damaged.
Redo the speaker wiring so that you can connect the unit to
the speakers as illustrated in Fig. 3.
– If the speaker wiring in your car is as illustrated in Fig. 3,
you can connect the unit using the original speaker wiring in
your car.
– If you are not sure of the speaker wiring of your car, consult
your car dealer.
+
L -
+
R -
!"#$%&'()*
• !"#$%&'&()*+,-./0123456
• !"#$%&"' ! !"#$ !"
! 12V !"#$ !"#$%&'()
• !"#$%&%' !"()*+,-./01 !"
– !"#$%&'()*12 !"#$%&'
!"#$%&'()*+,-./#0-123 !"# 3 !"#$%&'()*+
– !"#$%&'()*3 !"#$%&'() !"#$%
– !"#$ %&'()*+,-./ 0%&123 W??O?zU?Ðd?N?J?« W?U?D?« b?¹Ëe?ð ‰u?Š U?N?O?³?M?ð
∫ UŽUL« qOuðË
¨…—UO« W¹—UDÐ l UŽUL« WUÞ b¹Ëeð „öÝ« qÒuð ô •
Æ UŽULK —d{ ‰uBŠ v« ÍœR¹ p– Êô
W¹—UDÐ l® dHô« pK«Ë ¨©w{—ô«® œuÝô« pK« qË« •
·d??D? « l??® d??L? Šô« p??K? ? «Ë ¨©X??u?? ±≤ X??ÐU?Ł ¨…—U?O??«
Æ`O× qJAÐ ©wU{ô«
¨ U?ŽU?L??« l? U?ŽUL« WUÞ b¹Ëeð „öÝ« qOuð q³ •
Æpð—UOÝ qš«œ UŽUL« „öÝ« WJ³ý h׫
w?¼ U?L? p?ð—U?OÝ qš«œ UŽUL« „öÝ« WJ³ý X½U «–« ≠
quð
Ò
ô ¨qHÝô« w …œułu*« ≤ qJA«Ë ± qJA« w WMO³
ÆWOKô« UŽUL« „öÝ« WJ³ý «b²Ý« WDÝ«uÐ “UN'«
‰uBŠ v« p– ÍœROÝ ¨WI¹dD« ÁcNÐ “UN'« qOuð - «–«
p??M? J? 1 Y?O?×?Ð U?ŽU?L??« „ö?Ý« W?J?³?ý q?L?Ž b?Ž« Æ—d?{
Æ≥ qJA« w sÒO³ u¼ UL UŽUL« l “UN'« qOuð
w?¼ U?L? p?ð—U?OÝ qš«œ UŽUL« „öÝ« WJ³ý X½U «–« ≠
W??D? Ý«u??Ð “U??N? '« q??O? u??ð p??M? J? 1 ¨≥ q??J? ?A? ?« w?? W??M? ?O? ?³?
Æpð—UOÝ qš«œ WOKô« UŽUL« „öÝ« WJ³ý «b²Ý«
q??š«œ U??ŽU??L? ?« „ö?Ý« W?J?³?A?Ð p?²?d?F? Âb?Ž W?U?Š w? ≠
Æ’uB)« «cNÐ …d³)« ÍË– Ë« qOu« dA²Ý« ¨pð—UOÝ
+
+
L -
-
+
+
+
R -
-
Fig. 1
+
L -
-
+
+
R -
-
Fig. 2
Connecting the leads / !"#
+
-
+
-
Fig. 3
/ „öÝô« qOuð
Solder the core wires to
connect them securely.
!"#$%&'()
Twist the core wires when connecting.
!"#$%&'(
CAUTION / / tO³Mð
• To prevent short-circuit, cover the terminals of the UNUSED leads with insulating
tape.
• !"#$%&'()*+,%-./012
·«dÞ« vKŽ oôË ‰“UŽ j¹dý l{ ¨WOzUÐdNJ« ‡‡ dz«Ëb« w dOBI²« lM qł« s •
`O× qJAÐ „öÝô« r(«
ÆqOu²« bFÐ rJ×Ë
q³ `O× qJAÐ „öÝô« ÂdЫ
ÆqOu²«
ÆWKLF²*« dOž „öÝô«
B Connections Adding Other Equipment / !"#$%&'( / WOU{ô« Èdšô« …eNłô« qOuð
You can connect an amplifier and other equipment to upgrade
your car stereo system.
• Connect the remote lead (blue with white stripe) to the remote
lead of the other equipment so that it can be controlled through
this unit.
• For amplifier only:
– Connect this unit’s line-out terminals to the amplifier’s line-in
terminals.
– Disconnect the speakers from this unit, connect them to
the amplifier. Leave the speaker leads of this unit unused.
(Cover the terminals of the these unused leads with
insulating tape, as illustrated above.)
Amplifier / !" / uB«
!"#$%&'()* +,-./0123456
• ! !"# !"#$%&'()*+,-.
!"#$%&'(
• !"#$%
– !"#$%&'()"*$%+,-./
– !"#$%&'()*+,!-#$. !)/
!" !"#$%&'()*+,-.)%/0
!"
rC
Blue with white stripe
!"#$
iOÐôUÐ jD ‚—“« pKÝ
Rear speakers
!"
WOHK)« UŽUL«
L
INPUT
L
R
R
JVC amplifier
JVC JVC lM u rC
Signal cord (not supplied with this unit)
! !"#$%
©“UN'« «c¼ l od dOž® …—Uýô« pKÝ
LINE OUT
L
L
R
R
REAR
TROUBLESHOOTING
Y-connector (not supplied with this unit)
Y !" !"#$%
©“UN'« «c¼ l od dOž® Y ‡ qu
Remote lead
!"
bFÐ sŽ rJײ« pKÝ
To automatic antenna if any
!"#$%
błË Ê« wJOðUuðËô« wz«uN« v«
Purple with black stripe / Purple (Not used)
! / !
©qLF² dOž® w½«uł—ô«ØœuÝôUÐ jD w½«uł—« pKÝ
KS-FX201
(see diagram A ) Front speakers
A !"
WOUô« UŽUL« © A wDOD²« rÝd« dE½«®
Green with black stripe / Green (Not used)
! / !
©qLF² dOž® dCšô«ØœuÝôUÐ jD dCš« pKÝ
!
Õöô«Ë ‰UDŽô« sŽ Y׳«
• The fuse blows.
* Are the red and black leads connected correctly?
• * !"#
!"#$%&'!"#$%()*$+ ?
• Power cannot be turned on.
* Is the yellow lead connected?
• * !"#$
!"#$%&'$ ?
• No sound from the speakers.
* Is the speaker output lead short-circuited?
• * !"#$
!"#$%&'()*+ ?
• Sound is distorted.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• !"
* !"#$%&'() ?
* !"#$LR !"– !" ?
• Unit becomes hot.
* Is the speaker output lead grounded?
* Are the “–” terminals of L and R speakers grounded in common?
• !"
* !"#$%&'() ?
* !"#$LR !"– !" ?
Instal.EN.CH.AR.KS-FX201[U]
4
u¹dO²Ý “UNł ¡«œ« 5ײ dš« “UNłË u rC qOuð pMJ1
Æ…—UO«
p?K?Ý l? ©i?O?ÐôU?Ð j?D?<« ‚—“ô«® b?F?Ð s?Ž r?J?×?²?« p?KÝ qË« ¿
‰öš s “UN'UÐ rJײ« r²¹ YO×Ð dšô« “UN−K bFÐ sŽ rJײ«
Æ“UN'« «c¼
∫ uB« rC* jI ¿
j)« ‡ qšœ ·«dÞ« l “UN'« «cN j)« ‡ Ãdš ·«dÞ« qË« ‡‡
Æ uB« rC*
Æ uB« rC l rNKË« ¨“UN'« «c¼ s UŽUL« qB« ‡‡
wDž® ƉULF²Ý« ÊËbÐ “UN'« «c¼ UŽULÝ „öÝ« „dð«
`{u u¼ UL ¨‰“UŽ j¹dAÐ WKLF²*« dOž „öÝô« Ác¼ ·«dÞ«
©ÆvKŽô« w
3/24/05, 9:39 PM
Æ“uOH« ‚d²×¹
ø`O× qJAÐ Wuu œuÝô«Ë dLŠô« pK« q¼
ÆWOzUÐdNJ« WUD« qOuð sJ1 ô
øôuu dHô« pK« q¼
Æ UŽUL« s u —bB¹ ô
øWŽUL« Ãdš pKÝ …dz«œ w dOBIð pUM¼ q¼
ÆÁuA uB«
ø÷—ôUÐ ôuu WŽUL« Ãdš pKÝ q¼
R v?M?L?O?«Ë L Èd??O?« W?ŽU?L??K? å≠ò W?³?U??« ·«d?Þô« q¼
øiFÐ l ÷—ôUÐ Wuu
Æ“UN'« s¹
ø÷—ôUÐ ôuu WŽUL« Ãdš pKÝ q¼
R v?M?L?O?«Ë L Èd??O?« W?ŽU?L??K? å≠ò W?³?U??« ·«d?Þô« q¼
øiFÐ l ÷—ôUÐ Wuu
•
*
•
*
•
*
•
*
*
•
*
*
Download PDF