JVC LVT0862-001B User manual

JVC LVT0862-001B User manual
MICRO COMPONENT SYSTEM
UX-M5R — Consists of CA-UXM5R and SP-UXM5.
CD-R/RW PLAYBACK
MICRO
REC
SYSTEM
UX-M5R
STANDBY
/ON
OPEN/
CLOSE
DISPLAY
MODE
REMAIN
/RDS MODE
TIMER
ON/OFF
STANDBY/ON
CD/RANDOM
COMPONENT
TUNER
INTRO/RDS
SEARCH
SET
TAPE
/BAND
/REV.MODE
RANDOM
BAND
REV. MODE
PRE DOWN
PRE UP
CD
TUNER
TAPE
SLEEP
REPEAT
ST/MONO
PROGRAM
ST/MONO
STOP/CLEAR
SEARCH/TUNING
REPEAT
REMAIN
/RDS MODE
PHONES
VOLUME
REC
INTRO
/RDS SEARCH
TIMER
PROGRAM
DISPLAY
MODE
PRE EQ
/HBS
+
MUTING
BEAT CUT
VOLUME
PRESET
DIRECTION
PLAY/PAUSE
PRE EQ
/HBS
EJECT
–
RM-SUXM5R REMOTE CONTROL
AU TO R E V E R S E
FULL LOGIC DECK
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial No.
which are located either on the rear, bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0862-001B
[B]
00_FCV_UXM5R_B.p65
1
5/22/02, 7:41 PM
Warnings, Cautions and Others
IMPORTANT FOR LASER PRODUCTS
IMPORTANT for the U.K.
REPRODUCTION OF LABELS
DO NOT cut off the mains plug from this equipment. If the
plug fitted is not suitable for the power points in your home
or the cable is too short to reach a power point, then obtain
an appropriate safety approved extension lead or consult
your dealer.
1 CLASSIFICATION LABEL, PLACED ON EXTERIOR
SURFACE
CLASS
LASER
BE SURE to replace the fuse only with an identical
approved type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove
the fuse and dispose of the plug immediately, to avoid a
possible shock hazard by inadvertent connection to the
mains supply.
1
PRODUCT
2 WARNING LABEL, PLACED INSIDE THE UNIT
DANGER-Invisible laser radiation
when open and interlock defeated.
AVOID DIRECT EXPOSURE TO BEAM.
If this product is not supplied fitted with a mains plug then
follow the instructions given below:
VORSICHT-Unsichtbare Laserstrahlung,
wenn Abdeckung geöffnet und
Sicherheitsverriegelung überbrückt.
Nicht dem Straht aussetzen.
IMPORTANT:
DO NOT make any connection to the terminal which is
marked with the letter E or by the safety earth symbol or
coloured green or green-and-yellow.
ADVARSEL:USYNLIG LÅSERSTRALING
VED ÅBNING,NÅR SIKKERHEDSAFBRYDERE ER UDE AF FUNKTION.
UNDGÅ UDSATTELSE FOR STRÅLING.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue :
Neutral
Brown : Live
VARO! Avattaessa ja suojalukitus ohitettaessa
olet alttiina nädkmätön läsersateilylle.
Älä katso säteesen.
VARNING!Osymlig laserstrålning när denna
del är ösppad och spärren är urkopplad.
Betraka ej strålen.
ADVERSEL! Usynilig laserstråling når
deksel åpnes og slikkerhedslås brytes.
Unngå eksponering for sirålen.
A pleine puissance.I ecoute prolongee du
baladeur peut endommager l'oreille de
l'utilisaleur.
1. CLASS 1 LASER PRODUCT
2. DANGER: Invisible laser radiation when open and interlock
failed or defeated. Avoid direct exposure to beam.
3. CAUTION: Do not open the top cover. There are no user
serviceable parts inside the Unit; leave all servicing to
qualified service personnel.
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed as
follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured
black.
The wire which is coloured brown must be connected to
the terminal which is marked with the letter L or coloured
red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Caution –– STANDBY/ON
button!
Disconnect the mains plug to shut the power off completely. The
STANDBY/ON
button in any position does not disconnect the
mains line. The power can be remote controlled.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must be
considered and local rules or laws governing the disposal of
these batteries must be followed strictly.
• Do not use this apparatus in a bathroom or places with water.
Also do not place any containers filled with water or liquids
(such as cosmetics or medicines, flower vases, potted plants,
cups, etc.) on top of this apparatus.
Caution: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent damage, locate the apparatus as follows:
1 Front:
No obstructions and open spacing.
2 Sides/ Top/ Back:
No obstructions should be placed in the areas shown by the dimensions below.
3 Bottom:
Place on the level surface. Maintain an adequate air path for ventilation by placing on a stand with a height of 10 cm or more.
Front view
Side view
15 cm
1 cm
1 cm
15 cm
15 cm
15 cm
15 cm
UX-M5R
10 cm
– G-1 –
01_G1-G2UXM5R_B.p65
1
5/22/02, 7:41 PM
UX-M5R
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment,
care must be taken if you are to obtain the best results and safety is to be assured.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of
equipment) are properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when
making or changing connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮✮
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way —
switch off, withdraw the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended
operation or has a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is
illegal to watch television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s
approved stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case — this could result in
a fatal electrical shock.
— NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
01_G1-G2UXM5R_B.p65
2
5/22/02, 7:41 PM
Introduction
We would like to thank you for purchasing one of our JVC products.
Before operating this unit, read this manual carefully and thoroughly to
obtain the best possible performance from your unit, and retain this manual
for future reference.
About This Manual
Power sources
This manual is organized as follows:
• When unplugging from the wall outlet, always pull the
plug, not the AC power cord.
• The manual mainly explains operations using the
buttons and controls on the unit. You can also use the
buttons on the remote control if they have the same or
similar names (or marks) as those on the unit.
If operation using the remote control is different from
that using the unit, it is then explained.
• Basic and common information that is the same for many
functions is grouped in one place, and is not repeated in
each procedure. For instance, we do not repeat the
information about turning on/off the unit, setting the
volume, changing the sound effects, and others, which are
explained in the section “Common Operations” on pages 8
and 9.
• The following marks are used in this manual:
Gives you warnings and cautions to prevent a
damage or risk of fire/electric shock.
Also gives you information on operation which
is not good for obtaining the best possible
performance from the unit.
Gives you information and hints you had better
know.
DO NOT handle the AC power cord with wet
hands.
Moisture condensation
Moisture may condense on the lens inside the unit in the
following cases:
• After starting heating in the room
• In a damp room
• If the unit is brought directly from a cold to a warm place
Should this occur, the unit may malfunction. In this case,
leave the unit turned on for a few hours until the moisture
evaporates, unplug the AC power cord, and then plug it in
again.
Others
• Should any metallic object or liquid fall into the unit,
unplug the unit and consult your dealer before operating
any further.
• If you are not going to operate the unit for an extended
period of time, unplug the AC power cord from the wall
outlet.
DO NOT disassemble the unit since there are no
user serviceable parts inside.
Precautions
If anything goes wrong, unplug the AC power cord and
consult your dealer.
Installation
• Install in a place which is level, dry and neither too hot nor
too cold — between 5˚C and 35˚C.
• Install the unit in a location with adequate ventilation to
prevent internal heat built-up in the unit.
• Leave sufficient distance between the unit and the TV.
• Keep the speakers away from the TV to avoid interference
with TV.
DO NOT install the unit in a location near heat
sources, or in a place subject to direct sunlight,
excessive dust or vibration.
–1–
02_01_21_UXM5R_B_En.p65
1
5/22/02, 7:42 PM
Contents
Location of the Buttons and Controls ..................... 3
Front Panel ................................................................ 4
Remote Control ......................................................... 5
Getting Started .......................................................... 6
Unpacking ................................................................. 6
Putting the Batteries into the Remote Control .......... 6
Connections .............................................................. 6
Common Operations ................................................. 8
Turning On or Off the Unit ....................................... 8
Setting the Clock ....................................................... 8
Adjusting the Volume ................................................ 8
Digital Sound Control ............................................... 9
Listening to FM and MW Broadcasts ................... 10
Tuning In a Station .................................................. 10
Presetting Stations ................................................... 10
Tuning In a Preset Station ....................................... 10
Receiving FM Stations with RDS........................... 11
Changing the RDS Information .............................. 11
Searching for Programs by PTY Codes
(PTY Search) ..................................................... 11
Playing Back CDs .................................................... 12
Loading a Disc ........................................................ 12
Basic CD Operations .............................................. 12
Program Play ........................................................... 12
Random Play ........................................................... 13
Repeat Play ............................................................. 13
Introductory Play .................................................... 13
Displaying the Remaining Time during Playback .. 13
Playing Back Tapes ................................................. 14
Loading a Tape ........................................................ 14
Tape Playback ......................................................... 14
Auto Reverse ........................................................... 14
Rewind/Fast Forward .............................................. 14
Recording ................................................................. 15
Recording Tapes ...................................................... 15
Using the Timers ...................................................... 16
Using Daily Timer .................................................. 16
Timer Recording ..................................................... 16
Using Sleep Timer .................................................. 17
Description of the PTY Codes ................................ 18
Troubleshooting ....................................................... 18
Maintenance ............................................................ 19
Specifications ........................................................... 20
–2–
02_01_21_UXM5R_B_En.p65
2
5/22/02, 7:42 PM
Location of the Buttons and Controls
Become familiar with the buttons and controls on your unit.
Front Panel
Display Window
9
p
q
1
2
3
4
PROGRAM SLEEP HBS TOTAL REMAIN INTRO STEREO
RANDOM ONE
REPEAT ALL
ON OFF
5
CD SYNC
6
7
POP
CLASSIC
ROCK
TAPE
JAZZ
e
r
MHz
kHz
t
REC
y
8
u
i
1
w
CD-R/RW PLAYBACK
2
3
4
5
6
7
e
MICRO
COMPONENT
SYSTEM
UX-M5R
STANDBY
/ON
OPEN/
CLOSE
r
DISPLAY
MODE
REMAIN
/RDS MODE
t
INTRO/RDS
SEARCH
y
TIMER
ON/OFF
SET
PROGRAM
RANDOM
BAND
REV. MODE
CD
TUNER
TAPE
ST/MONO
STOP/CLEAR
SEARCH/TUNING
REPEAT
8
PHONES
VOLUME
REC
PRESET
DIRECTION
PLAY/PAUSE
u
PRE EQ
/HBS
i
9
EJECT
p
q
3
o
;
AU TO R E V E R S E
FULL LOGIC DECK
a
–3–
02_01_21_UXM5R_B_En.p65
w
5/22/02, 7:42 PM
Continued
Front Panel
See pages in the parentheses for details.
1 Disc compartment (12)
2
STANDBY/ON button (8)
Turns the unit on or off (standby mode).
3 CD/RANDOM button (12, 13)
Selects CD mode.
Starts or stops random play in CD mode.
4 DISPLAY MODE button (8, 16)
Displays the clock time or sets the timer.
5 TIMER ON/OFF SET button (16)
Activates/deactivates the timer.
6 Remote sensor (5)
Infrared sensor for remote control
7 PROGRAM button (8, 10, 12, 16)
CD: programs the track playback order.
Tuner: presets radio stations.
Clock/Timer: sets the clock/timer.
8 REPEAT button (13)
CD: repeats a track or the whole disc.
ST/MONO button (10)
Tuner: switches between stereo and monaural mode (on
FM band only).
STOP/CLEAR 7 button (12, 14)
CD: stops playback or clears the program.
Tape: stops playback or recording.
9 PHONES jack (8)
Connect the headpones to this jack.
p Tape deck (14)
q REC ¶ (Recording) button (15)
Switches to record ready state.
w TUNER/BAND button (10)
Selects tuner mode.
Selects FM or MW in tuner mode.
e TAPE/REV.MODE button (14)
Selects tape mode.
Selects auto reverse mode.
r 0 OPEN/CLOSE button (12)
Opens/closes the disc compartment.
t REMAIN/RDS MODE button (11, 13)
CD: displays the remaining time of a track/disc or
elapsed time of a disc during playback.
Tuner (FM): displays RDS information.
y INTRO/RDS SEARCH button (11, 13)
CD: starts or stops introductory play.
Tuner (FM): selects RDS search.
u VOLUME +/– buttons (8)
Adjust the volume.
i PRE EQ/HBS button (9)
Selects the desired sound mode.
Switches on or off the HBS system.
o 0 EJECT (14)
Opens the tape deck door.
; SEARCH/TUNING 4 / ¢ buttons (8, 10, 12, 14, 16)
CD: search backward/forward or skip to the beginning of
the current/previous/next track.
Tuner: tune to a lower or higher radio frequency or
search radio stations.
Tape: rewind or fast forward.
Clock/Timer: set the hour and minute.
a DIRECTION 8/2 and 3/8 buttons (14)
Tape: start playback or recording in the selected
direction.
PLAY/PAUSE 3/8 button (12, 14)
CD/Tape: starts or interrupts playback.
PRESET ∞ / 5 buttons (10)
Tuner: Selects a preset radio station.
Display window
1
2
3
4
5
6
7
8
9
p
q
w
e
r
t
y
u
i
/ON/OFF (timer on/off) indicators (16)
HBS indicator (9)
SLEEP indicator (17)
PROGRAM indicator (10, 12)
RDS indicator (11)
Main display
Sound mode indicators (9)
POP, CLASSIC, ROCK, JAZZ
3 (play mode) indicator (12, 14)
TOTAL/REMAIN indicators (13)
RANDOM indicator (13)
INTRO indicator (13)
STEREO indicator (10)
REPEAT ONE/ALL indicators (13)
CD SYNC (synchronous recording) indicator (15)
MHz/kHz (frequency) indicators (10)
REC/8 (recording/pause) indicators (15)
(tape direction) indicator (14, 15)
TAPE indicator (14)
–4–
02_01_21_UXM5R_B_En.p65
4
5/22/02, 7:42 PM
Remote Control
Remote Control
1
2
w
STANDBY/ON
CD/RANDOM
3
REC
4
5
6
7
TUNER
TAPE
/BAND
/REV.MODE
PRE DOWN
PRE UP
e
r
t
REMAIN
/RDS MODE
SLEEP
REPEAT
ST/MONO
INTRO
/RDS SEARCH
TIMER
PROGRAM
DISPLAY
MODE
PRE EQ
/HBS
+
BEAT CUT
VOLUME
y
u
8
MUTING
9
i
o
–
p
;
q
1
2
3
4
5
6
7
8
9
p
q
RM-SUXM5R REMOTE CONTROL
w
e
r
t
y
u
i
o
;
STANDBY/ON button
CD/RANDOM button
TUNER/BAND button
REC (Recording) button
7 button
REMAIN/RDS MODE button
INTRO/RDS SEARCH button
TIMER button
DISPLAY MODE button
PRE EQ/HBS button
MUTING button
Interrupts and resumes sound reproduction.
TAPE/REV. MODE button
PRE DOWN 8/2 button
PRE UP 3/8 button
4/¢ buttons
REPEAT ST/MONO button
SLEEP button
Selects the time length until the unit is turned off.
PROGRAM button
VOLUME +/– buttons
BEAT CUT button
Eliminates beats during MW broadcast recording.
CD-R/RW PLAYBACK
MICRO
COMPONENT
SYSTEM
U X - M 35 R
STANDBY
/ON
OPEN/
OPEN
CLOSE
/CLOSE
DISPLAY
MODE
REMAIN
/RDS MODE
TIMER
TIMER
ON/OFF
ON/OFF
INTRO/RDS
SEARCH
SET
SET
PROGRAM
RANDOM
BAND
REV. MODE
CD
TUNER
TAPE
PRESET
ST/MONO
STOP/CLEAR
SEARCH/TUNING
REPEAT
PHONES
VOLUME
PRESET
STOP/CLEAR
DIRECTION
PLAY/PAUSE
REC
PRE
PRE EQ
EQ
/HBS
EJECT
When using the remote control, point it at the remote
sensor on the front panel.
–5–
02_01_21_UXM5R_B_En.p65
5
5/22/02, 7:42 PM
Getting Started
Continued
Unpacking
Connections
After unpacking, check to be sure that you have all the
following items.
The number in the parentheses following each item name
indicates the supplied quantity.
• DO NOT connect any equipment to the unit while the
unit is powered.
• DO NOT plug in any equipment until all connections
are completed.
• Remote control (1)
• Batteries (R03 (UM-4)/AAA (24F)) for remote control (2)
• AM loop antenna (1)
If any is missing, consult your dealer immediately.
3
Putting the Batteries into the Remote Control
Insert 2 batteries — R03 (UM-4)/AAA (24F) — into the
battery compartment of the remote control, complying with
the + and – polarity markings inside the battery compartment.
When the remote control can no longer operate the unit,
replace both batteries at the same time.
2
AM
LOOP
FM
ANT
RIGHT
1
LEFT
L
L
R
R
1
4
R03(UM-4)/
AAA(24F)
1 Connect the speakers.
2
Connect the right speaker to the “R” terminals, with the
red wire to + and the black wire to –.
Connect the left speaker to the “L” terminals in the same
way.
Clip the stripped portion of each speaker wire as shown in
the illustration.
3
•
•
•
•
DO NOT use an old battery together with a new one.
DO NOT use different types of batteries together.
DO NOT expose batteries to heat or flame.
DO NOT leave the batteries in the battery
compartment when you are not going to use the
remote control for an extended period of time;
otherwise, the remote control may be damaged by
battery leakage.
–6–
02_01_21_UXM5R_B_En.p65
6
5/22/02, 7:42 PM
2 Connect the supplied AM loop antenna to the
AM LOOP terminal.
Place the antenna away from the unit and adjust its
position for the best reception.
1
2
3
3 Adjust the position of the FM antenna for the
best reception.
4 Connect the AC power cord of the unit to the
AC outlet after all other connections have
been made.
To remove the speaker grilles
The speaker grilles can be removed as shown in the
illustration below.
Holes
Projections
Speaker grille
To remove the speaker grille, inserting your fingers at the
top of the speaker grille, pull it towards you. Then pull the
bottom towards you.
To attach the speaker grille, put the projections of the
speaker grille into the holes of the speaker.
–7–
02_01_21_UXM5R_B_En.p65
7
5/22/02, 7:42 PM
Common Operations
Continued
Turning On or Off the Unit
On clock resetting
If a power failure occurs or the AC power cord is
disconnected, the clock is reset to "00:00" (flashing). In such
a case you need to set the clock again.
To turn on the unit
Press
STANDBY/ON on the
unit or remote control.
The unit turns on with the last source
selection remaining valid.
STANDBY/ON
STANDBY
/ON
or
Adjusting the Volume
To turn off the unit (on standby)
• You can adjust the volume only while the unit is turned on.
Press
STANDBY/ON on the unit or remote control.
The clock time appears if the clock is already set.
Setting the Clock
Press VOLUME + or
VOLUME – to increase or
decrease the volume level.
Before operating the unit any further, first set the built-in
clock.
The volume can be adjusted in 41 steps
between “VOL MIN” (minimum) and
“VOL MAX” (maximum).
1 When the unit is in standby
mode, press and hold
PROGRAM until the hour
indication starts blinking.
PROGRAM
To increase or decrease the volume level rapidly, press and
hold VOLUME + or VOLUME –.
To turn off the sound temporarily
• When the unit is on, press DISPLAY MODE to enter clock
mode, then press and hold PROGRAM.
2 Press 4 or ¢ to set the
hour, then press
PROGRAM.
3 Press 4 or ¢ to set the
minute, then press
PROGRAM to store the
setting.
Press MUTING on the remote control.
Playback continues without sound and
“MUTING” appears on the display.
For private listening
Connect a pair of headphones to the PHONES jack. No sound
comes out of the speakers. Be sure to turn down the volume
before connecting or putting on headphones.
SEARCH/TUNING
The clock starts working.
To change the hour or minute indication rapidly in steps 2
and 3, press and hold 4 or ¢.
DO NOT turn off the unit (on standby) with the volume
set to an extremely high level; otherwise, a sudden blast
of sound can damage your hearing and/or the speakers
when you turn on the unit or start playing any source
next time.
To select 12-hour or 24-hour display mode
PROGRAM
STOP/CLEAR
and
• In 12-hour mode, “AM 12:00” indicates midnight and “PM
12:00” indicates noon.
To check the clock time while the unit is on
Press DISPLAY MODE.
The clock time is displayed until you
press any key.
DISPLAY
MODE
To correct the clock time
Carry out steps 1 to 3 above.
–8–
02_01_21_UXM5R_B_En.p65
8
MUTING
To restore the sound, press MUTING again or increase or
decrease the volume level.
SEARCH/TUNING
The minute indication starts
blinking.
In standby mode, hold down
7 and press PROGRAM on the
unit repeatedly.
With each press, the selection
toggles between 12-hour and 24hour modes.
VOLUME
5/22/02, 7:42 PM
Digital Sound Control
The unit’s digital sound control feature enables you to select
desired preset equalizer settings (selectable as sound modes)
to enjoy special sound effects matching the music type.
You can also use the HBS (Hyper Bass Sound) system to
enjoy powerful bass sound created by emphasizing low
frequencies.
To select the desired sound mode
PRE EQ
/HBS
Press PRE EQ/HBS repeatedly.
Each time you press the button, the
sound mode changes as follows:
POP
CLASSIC
FLAT
ROCK
JAZZ
POP: More presence in the vocals and midrange
CLASSIC: Enriched sound with fine treble and ample bass
ROCK: Powerful sound emphasizing treble and bass
JAZZ: Accented lower frequencies for jazz-type music
FLAT: Equalizer effect is cancelled.
To switch the HBS system on/off
Press and hold PRE EQ/HBS until
“HBS ON” or “HBS OFF” appears on
the display.
When the HBS system is switched on,
the HBS indicator lights up on the
display.
PRE EQ
/HBS
–9–
02_01_21_UXM5R_B_En.p65
9
5/22/02, 7:42 PM
Listening to FM and MW Broadcasts
Tuning In a Station
Presetting Stations
You can preset 20 FM and 20 MW stations.
1 When the unit is turned on,
press TUNER/BAND to
select tuner mode.
BAND
TUNER
• There is a time limit in doing the following steps. If the
setting is cancelled before you finish, start from step 1
again.
The unit tunes in the last station
tuned in (either FM or MW).
2 Press TUNER/BAND to
select the band, FM or MW.
1 Tune in the station you want to preset.
BAND
TUNER
• See “Tuning In a Station” on the left.
Each time you press the button, the
band selection alternates between
FM and MW.
3 Press and hold 4 or ¢
for more than 1 second.
2 Press PROGRAM.
PROGRAM
The PROGRAM indicator and “00”
start blinking on the display.
SEARCH/TUNING
3 Press PRESET ∞ or 5 (or
PRE DOWN 8/2 or PRE
UP 3/8 on the remote
control) to specify the
desired preset number.
The unit starts searching for stations
and stops when a station of sufficient
signal strength is tuned in.
If a program is broadcast in stereo,
the STEREO indicator lights up.
PRESET
DIRECTION
PLAY/PAUSE
4 To preset more stations, repeat steps 1 to 3
above, allocating a different preset number to
each station.
To stop searching, press 4 or ¢.
When you press 4 or ¢ briefly and repeatedly
The frequency changes step by step.
When a new station is stored
The station previously memorized with the same preset
number is erased. (The frequency of the new station replaces
the previous frequency in memory.)
To improve the FM reception
When an FM stereo broadcast is hard to
receive or noisy, press REPEAT ST/
MONO to switch to the monaural
reception. The STEREO indicator
disappears from the display.
ST/MONO
REPEAT
Tuning In a Preset Station
To restore the stereo reception, press REPEAT ST/MONO
again so that the STEREO indicator lights up.
1 Press TUNER/BAND to
select tuner mode.
BAND
TUNER
2 Press TUNER/BAND to select the band, FM
or MW.
3 Press PRESET ∞ or 5 (or
PRE DOWN 8/2 or PRE
UP 3/8 on the remote
control) to select the desired
preset number.
– 10 –
02_01_21_UXM5R_B_En.p65
10
5/22/02, 7:42 PM
PRESET
DIRECTION
PLAY/PAUSE
Receiving FM Stations with RDS
RDS (Radio Data System) allows FM stations to send an
additional signal along with their regular program signals.
For example, the stations send their station names, as well as
information about what type of program they broadcast, such
as sports or music, etc.
When tuned to an FM station which provides the RDS
service, the RDS indicator lights up on the display.
With the unit, you can receive the following types of RDS
signals.
PS (Program Service):
Shows commonly known station names.
Searching for Programs by PTY Codes
(PTY Search)
One of the advantages of RDS is that you can locate a
particular kind of program by specifying the PTY (Program
Type) codes.
• For details on each of the PTY codes, see “Description of
the PTY Codes” on page 18.
• There is a time limit in doing the following steps. If the
setting is cancelled before you finish, start from step 1
again.
PTY (Program Type):
Shows types of broadcast programs.
1 Press INTRO/RDS
SEARCH until the PTY
code you want appears on
the display.
RT (Radio Text):
Shows text messages the station sends.
More about RDS
• Some FM stations do not provide RDS signals.
• RDS services vary among FM RDS stations. For details on
RDS services in your area, check with local radio stations.
• RDS may not work correctly if the received station is not
transmitting the signals properly or if the signal strength is
weak.
Each time you press the button, the
PTY codes change as follows:
NEWS
SCIENCE
OTHER M
Press REMAIN/RDS MODE.
PS
PTY
DRAMA
VARIED
CLASSICS
EDUCATE
POP M
ROCK M
LIGHT M
MOR M
SEARCH/TUNING
• If no program is found, the unit returns to the last received
station.
RT
To stop searching during the process, press INTRO/RDS
SEARCH.
• If no PS, PTY, or RT signals are sent by a station,
“NO PS”, “NO PTY”, or “NO TEXT” appears on the
display.
On the characters displayed
When the display shows PS, PTY or RT signals:
– The display shows upper case letters only.
– The display cannot show accented letters; For example,
“A” may represent accented “A’s” like “Á, Â, Ã, À, Ä and
Å ”.
– 11 –
11
SPORT
The unit searches FM stations, stops
when it finds the one you have
selected, and tunes in that station.
Station frequency
02_01_21_UXM5R_B_En.p65
INFO
2 Press 4 or ¢.
REMAIN
/RDS MODE
Each time you press the button, the
display changes to show the following
information:
AFFAIRS
CULTURE
Changing the RDS Information
You can see RDS information on the display while listening
to an FM station.
INTRO/RDS
SEARCH
5/22/02, 7:42 PM
Playing Back CDs
Continued
This unit can play back audio CDs and CD-R/RW discs.
Program Play
You can arrange the order in which the tracks are played
before you start playing. You can program up to 60 tracks.
1 In stop mode, press
PROGRAM.
Loading a Disc
1 Press CD/RANDOM to
select CD mode.
RANDOM
The PROGRAM indicator starts
blinking.
CD
2 Press 0 OPEN/CLOSE.
OPEN/
CLOSE
The disc tray slides out.
PROGRAM
2 Press 4 or ¢ repeatedly
to select the desired track.
SEARCH/TUNING
The current program number starts blinking.
3 Load a disc with the label side facing up.
3 Press PROGRAM to store
the selected track.
PROGRAM
“00” and the next program number
appear on the display.
4 Repeat steps 2 and 3 to store other tracks.
• You cannot program more than 60 tracks. If you attempt to
do it, “FULL” will flash on the display.
To review the programed sequence
4 Press 0 OPEN/CLOSE to
close the disc compartment.
OPEN/
CLOSE
The total number of tracks and the
playing time of the disc appear on
the display.
PLAY/PAUSE
The 3 indicator lights up and the
track number and elapsed playing
time of the current track appear on
the display.
2 To stop playback, press 7.
PROGRAM
To modify the program
Basic CD Operations
1 Press 3/8 to start playback.
Press PROGRAM repeatedly in stop mode.
The program number and track number
are displayed in succession.
Press PROGRAM repeatedly to select
the program number with which you
want to change the track, then repeat
steps 2 and 3 above.
PROGRAM
To play the programed tracks
Press 3/8.
STOP/CLEAR
PLAY/PAUSE
• During program play, you can press
4 or ¢ to select the desired track
in the program.
To interrupt playback
Press 3/8.
The 3 indicator and the playing time
starts blinking.
PLAY/PAUSE
If you press REPEAT ST/MONO during
program play
The current track or all programed tracks are played
repeatedly.
To resume playback, press 3/8 again.
To select a desired track
Press 4 or ¢ repeatedly until the
desired track appears on the display.
To clear the program
SEARCH/TUNING
To search for a particular point during playback
Press and hold 4 or ¢ to locate the
desired point.
SEARCH/TUNING
Press 7 in stop mode.
The PROGRAM indicator disappears
from the display.
• The stored program is cleared when the disc compartment
is opened.
– 12 –
02_01_21_UXM5R_B_En.p65
12
STOP/CLEAR
5/22/02, 7:42 PM
Random Play
Introductory Play
You can play all the tracks in random order.
The introductory portions of tracks can be played back
automatically.
Press CD/RANDOM before or
during playing.
RANDOM
Press INTRO/RDS SEARCH.
CD
The first 10-second portion of each of
the tracks is played back in order.
The RANDOM indicator lights up.
To exit random play mode, press CD/RANDOM again.
The RANDOM indicator goes off.
To exit introductory play mode, press INTRO/RDS
SEARCH again.
• Activating the REPEAT ONE function during random play
mode disables the random play mode.
• It is not possible to activate the random play function
during program play mode.
• The introductory play function is also available during
program play mode, random play mode and repeat play
mode.
Displaying the Remaining Time during
Playback
Repeat Play
You can play the current track or the whole disc repeatedly.
Press REPEAT ST/MONO
repeatedly to select either of the
following repeat play modes:
You can display the remaining time of the current track/disc
and the elapsed time of the current track/disc during playing a
CD.
ST/MONO
REPEAT
Press REMAIN/RDS MODE
repeatedly to select one of the
following time display modes:
REPEAT ONE: repeats the current track.
REPEAT ALL: repeats the whole disc.
The current track or the whole disc is played repeatedly until
you press 7.
• Activating the random play function during REPEAT ONE
play mode disables the repeat play mode.
– 13 –
13
REMAIN
/RDS MODE
REMAIN: shows the remaining time of the current track.
TOTAL REMAIN: shows the remaining time of the disc.
TOTAL: shows the elapsed time of the disc.
No indication: shows the elapsed time of the current track.
To exit repeat play mode, press REPEAT ST/MONO
repeatedly so that the REPEAT indicator disappears from the
display.
02_01_21_UXM5R_B_En.p65
INTRO/RDS
SEARCH
5/22/02, 7:42 PM
Playing Back Tapes
Auto Reverse
• Use only type I normal tapes.
The use of tapes longer than 120 minutes is not
recommended, since characteristic deterioration may
occur and these tapes easily jam in the pinch roller and
the capstan.
Loading a Tape
1 Press 0 EJECT to open the
tape deck door.
Press TAPE/REV.MODE repeatedly
to select the desired playback mode.
REV. MODE
TAPE
: playback on one side of the tape only.
: both sides are played once.
:both sides are played repeatedly up to 10 times until you
press 7.
Rewind/Fast Forward
EJECT
1 Press 4 or ¢ to rewind
or fast forward the tape.
SEARCH/TUNING
“REW” or “FF” appears on the
display.
2 Insert a recorded tape with the open side
down.
2 Press 7 to stop rewinding or
fast forwarding.
STOP/CLEAR
• The tape stops automatically at the end of the rewinding or
fast forwarding.
3 Close the tape deck door.
The TAPE indicator appears on the display.
Tape Playback
1 Press TAPE/REV.MODE.
REV. MODE
TAPE
2 Press 8/2 or 3/8 to select
the playback direction.
PRESET
DIRECTION
PLAY/PAUSE
Playback starts.
“PLAY” appears on the display and
the playback direction indicator
moves to show the tape direction.
3 To stop playback, press 7.
STOP/CLEAR
To interrupt playback
Press the last selected 8/2 or 3/8.
“PAUSE” appears on the display.
PRESET
DIRECTION
PLAY/PAUSE
• If you press the button opposite to the last selected
direction, playback starts in the reverse direction.
To resume playback, press 8/2 or 3/8 again.
– 14 –
02_01_21_UXM5R_B_En.p65
14
5/22/02, 7:42 PM
Recording
Recording Tapes
IMPORTANT:
• It should be noted that it may be unlawful to re-record
pre-recorded tapes, records, or discs without the
consent of the owner of copyright in the sound or video
recording, broadcast or cable program and in any
literary, dramatic, musical, or artistic content embodied
therein.
• The recording level is automatically set correctly, so it is
not affected by the volume control. Thus, during recording
you can adjust the sound you are actually listening to
without affecting the recording level.
• While recording, you can hear sound modes and/or the
HBS sound effect through the speakers. However, the
sound is recorded without these effects (see page 9).
• If recordings you have made have excessive noise or static,
the unit may be too close to a TV. Increase the distance
between the TV and the unit.
• Use only type I normal tapes for recording.
• The use of tapes longer than 120 minutes is not
recommended, since characteristic deterioration may occur
and these tapes easily jam in the pinch roller and the
capstan.
To protect your recording
Cassettes have two small tabs on the back to prevent
unexpected erasure or re-recording.
To protect your recording, remove these tabs.
To re-record on a protected tape, cover the holes with
adhesive tape.
1 Load a recordable tape into the tape deck.
2 Press TAPE/REV.MODE
repeatedly to either record one
side or both sides of the tape.
REV. MODE
TAPE
: recording on one side only
: recording on both sides
• When you select
, make sure that there is no content that
should not be lost is recorded on either side of the tape.
3 Press CD/RANDOM or
TUNER/BAND to select the
desired recording source.
RANDOM
BAND
or
CD
TUNER
4 Prepare the source.
• For synchronous recording of a CD
Load the disc (see page 12).
– To start recording from the desired track, select the track
by pressing 4 or ¢ repeatedly in stop mode.
– To start recording from the desired point on a disc, play
the disc and pause at the desired point by pressing 3/8.
• For recording from the radio
Tune in the desired station (see page 10).
5 Press REC.
REC
“REC” is displayed. The TAPE REC
indicator and “8” light up and the
recording direction indicator starts
blinking.
6 While the recording
direction indicator is
blinking, press 8/2 or 3/8
to select the recording
direction.
PRESET
DIRECTION
PLAY/PAUSE
Recording starts.
“8” goes off. The TAPE REC indicator remains on the
display. When recording a CD, the CD SYNC indicator
also lights up.
To stop recording, press 7.
The selected recording source continues playing.
• During recording, it is not possible to pause or listen to
another source. “REC ON” appears on the display.
• Recording continues to the end of the tape until you press
7 even after playback of the CD has finished.
Using the BEAT CUT function
When recording an MW broadcast, beats may occur. If this
happens, press BEAT CUT on the remote control to select the
better beat-cut position, “BEAT 01” or “BEAT 02”.
– 15 –
02_01_21_UXM5R_B_En.p65
15
5/22/02, 7:42 PM
Using the Timers
Continued
There are three timers available – daily timer, recording timer
and sleep timer.
Before using the timers, you need to set the built-in clock
(see page 8).
Using Daily Timer
With the daily timer, you can wake to your favourite music or
radio program.
At the timer-on time, the unit automatically turns on, sets the
volume to the preset level, and starts playing the specified
source (radio or CD). Then, at the timer-off time, the unit
automatically turns off (on standby).
The timer setting remains in memory until you change it.
• There is a time limit in doing the following steps. If the
setting is cancelled before you finish, start from step 1
again.
DISPLAY
MODE
PROGRAM
The hour indication starts blinking.
2 Press 4 or ¢ to set the
timer start hour, then press
PROGRAM.
To listen to the radio, tune in the desired station.
To listen to a CD, load the disc.
9 Press TIMER ON/OFF SET
(or TIMER on the remote
control) to activate the timer.
“
TIMER
ON/OFF
SET
” lights up on the display.
10 Turn off the unit (on standby).
How the daily timer actually works
1 Press and hold DISPLAY
MODE until “ ON” starts
blinking on the display, then
press PROGRAM.
8 Prepare the source and set the volume.
SEARCH/TUNING
When the preset time is reached, the
selected source is played if the timer
has been activated.
STANDBY
/ON
To deactivate the timer, press TIMER ON/OFF SET (or
TIMER on the remote control).
“ ” disappears from the display.
• The timer function is not activated if the starting and
stopping times are the same.
• If the selected source (CD or TAPE) is not available when
preset time is reached, TUNER is selected automatically.
Timer Recording
You can use the recording timer to record a preset radio
station from a specified time and for a specified duration
automatically.
1 Load a recordable tape into the tape deck.
The minute indication starts blinking.
• If desired, select the tape reverse mode option.
3 Press 4 or ¢ to set the
minute, then press
PROGRAM.
“
SEARCH/TUNING
2 Follow the “Using Daily Timer” procedure on
the left. Select “REC TU” as the source for
timer recording.
ON” starts blinking again.
4 Press DISPLAY MODE so
that “ OFF” starts
blinking on the display, then
press PROGRAM.
DISPLAY
MODE
PROGRAM
The hour indication starts blinking.
• If the preset time is reached while the unit is on, the timer
is not activated for timer recording.
• Once the recording is finished, the recording timer is
replaced by the daily timer with the source selection
changed from “REC TU” to “TUNER”.
5 Set the time to stop playback
following the same
procedure as steps 2 and 3.
6 Press DISPLAY MODE so
that “TUNER,” “TAPE,”
“CD” or “REC TU” appears
on the display, then press
PROGRAM.
7 Press 4 or ¢ to select
the desired source, then
press PROGRAM.
DISPLAY
MODE
PROGRAM
SEARCH/TUNING
– 16 –
02_01_21_UXM5R_B_En.p65
16
5/22/02, 7:42 PM
Using Sleep Timer
With the sleep timer, you can fall asleep to music.
You can set the sleep timer using the remote control when the
unit is turned on.
How the sleep timer actually works
The unit automatically turns off after the specified time
length passes.
1 Press and hold SLEEP on
the remote control until the
desired time length appears
on the display.
SLEEP
The time length changes from 90 to 10 minutes in
10-minute steps.
2 Wait for a moment after specifying the time
length.
The SLEEP indicator lights up steadily on the display.
• Setting both the timer-off and sleep-off times causes the
unit to enter standby mode when the earlier one of them is
reached.
To change the shut-off time, repeat the procedure above.
To cancel the setting, press SLEEP so that the SLEEP
indicator goes off.
• The sleep timer is also cancelled when you turn off the
unit.
– 17 –
02_01_21_UXM5R_B_En.p65
17
5/22/02, 7:42 PM
Description of the PTY Codes
NEWS:
News.
POP M:
AFFAIRS: Topical program expanding or enlarging upon the news
– debate, or analysis.
Commercial music of current popular appeal.
ROCK M: Rock music.
MOR M:
Easy-listening music of relatively short duration.
INFO:
Program the purpose of which is to impart advice in
the widest sense.
LIGHT M: Instrumental music, and vocal or choral works.
SPORT:
Program concerned with any aspect of sports.
CLASSICS: Performances of major orchestral works, symphonies,
chamber music, etc.
EDUCATE: Educational programs.
DRAMA:
OTHER M: Music not fitting into any of the other categories.
All radio plays and serials.
CULTURE: Programs concerning any aspect of national or regional
culture, including language, theater, etc.
SCIENCE: Programs about natural sciences and technology.
VARIED:
Classification of the PTY codes for some FM stations
may be different from the above list.
Used for mainly speech-based programs such as
quizzes, panel games and personality interviews.
Troubleshooting
If you are having a problem with your unit, check this list for a possible solution before calling for service.
If you cannot solve the problem from the hints given here, or the unit has been physically damaged, call a qualified person,
such as your dealer, for service.
Symptom
No sound is heard.
Cause
Action
• Connections are incorrect or loose.
• Check all connections and make
corrections. (See pages 6 and 7.)
• Headphones are connected.
• Disconnect the headphones.
• Antennas are disconnected.
• Reconnect the antennas correctly and
securely.
• The AM loop antenna is too close to the
unit.
• Change the position and direction of the
AM loop antenna.
• The FM antenna is not properly extended
and positioned.
• Extend the FM antenna at the best
position.
The disc tray does not open or close.
The AC power cord is not plugged in.
Plug the AC power cord.
The disc does not play.
The disc is placed upside down.
Place the disc with the label side up.
The disc sound is discontinuous.
The disc is scratched or dirty.
Clean or replace the disc. (See page 19.)
The cassette holder cannot be opened.
Power supply from the AC power cord has
been cut off while the tape was running.
Turn on the unit.
Impossible to record.
Small tabs on the back of the cassette are
removed.
Cover the holes with adhesive tape.
Operations are disabled.
The built-in microprocessor may
malfunction due to external electrical
interference.
Unplug the AC power cord and then plug it
back in.
Unable to operate the unit from the remote
control.
• The path between the remote control and
the remote sensor on the unit is blocked.
• Remove the obstruction.
• The batteries are exhausted.
• Replace the batteries.
Hard to listen to broadcasts because of
noise.
– 18 –
02_01_21_UXM5R_B_En.p65
18
5/22/02, 7:42 PM
Maintenance
To get the best performance of the unit, keep your discs, tapes, and mechanism clean.
Handling discs
Cassette decks
• Remove the disc from its case by
holding it at the edge while pressing
the centre hole lightly.
• Do not touch the shiny surface of the
disc, or bend the disc.
• Put the disc back in its case after use
to prevent warping.
If the head, capstan, and pinch roller of the cassette deck
become dirty, the following will occur:
• Impaired sound quality
• Discontinuous sound
• Fading
• Incomplete erasure
• Difficulty in recording
To clean the head, capstan, and pinch roller
Use a cotton swab moistened with alcohol.
• Be careful not to scratch the surface
of the disc when placing it back in its
case.
• Avoid exposure to direct sunlight,
temperature extremes, and moisture.
Capstan
Head
To clean the disc
Wipe the disc with a soft cloth in a
straight line from centre to edge.
Pinch roller
DO NOT use any solvent — such as conventional record
cleaner, spray, thinner, or benzine — to clean the disc.
To demagnetize the head
Turn off the unit, and use a head demagnetizer (available at
electronics and record shops).
Cleaning the unit
Handling cassette tapes
• If the tape is loose in its cassette, take
up the slack by inserting a pencil in
one of the reels and rotating.
• If the tape is loose, it may get
stretched, cut, or caught in the
cassette.
• Be careful not to touch the tape
surface.
• Stains on the unit
Should be wiped off with a soft cloth. If the unit is heavily
stained, wipe it with a cloth soaked in water diluted neutral
detergent and wrung well, then wipe clean with a dry cloth.
• Since the unit may deteriorate in quality, become
damaged or get its paint peeled off, be careful about the
followings.
– DO NOT wipe it with a hard cloth.
– DO NOT wipe it strong.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as
insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact
with it for a long time.
• Avoid the following places to store the
tape:
– In dusty places
– In direct sunlight or heat
– In moist areas
– Near a magnet
– 19 –
02_01_21_UXM5R_B_En.p65
19
5/22/02, 7:42 PM
Specifications
Amplifier section
General
Output power
60 W (30 W + 30 W) at 8 Ω (MAX.)
22 W per channel, min. RMS, driven into 8 Ω at
1 kHz, with no more than 10% total harmonic
distortion (IEC 268-3)
Audio output level
PHONES:
800 mV/32 Ω
Speakers/Impedance
8 Ω - 16 Ω
Power requirement
Power consumption
Dimensions
Mass
Speaker
Woofer: 10.2 cm cone × 1
Tweeter: 5.1 cm cone × 1
8Ω
160 mm × 269.5 mm × 200 mm
(W/H/D)
2 kg/piece
Speaker unit
Tuner
FM tuning range
MW tuning range
87.50 MHz - 108.00 MHz
522 kHz - 1 629 kHz
CD player
Impedance
Dimensions
Mass
Dynamic range
Signal-to-noise ratio
Wow and flutter
60 dB
60 dB
Unmeasurable
Cassette deck
Supplied accessories
See page 6.
Design and specifications are subject to change without
notice.
Frequency response
Normal (type I):
Wow and flutter
100 Hz - 10 000 Hz
0.35% (WRMS)
– 20 –
02_01_21_UXM5R_B_En.p65
AC 230 V Ó, 50 Hz
40 W (operation mode)
1 W (standby mode)
160 mm × 269.5 mm × 340 mm
(W/H/D)
5 kg
20
5/22/02, 7:42 PM
0502NNMBICORI
EN
99_BCV_UXM5R_B.p65
2
5/22/02, 7:43 PM
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement