JVC | RX-7010RBK | User's Manual | JVC RX-7010RBK User's Manual

AUDIO/VIDEO CONTROL RECEIVER
RX-7010RBK / RX-7012RSL
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MUILTI
CD
FM/AM
VCR
TAPE/CDR
PHONO
+
−
+
TV/DBS
−
BASS
SURROUND
DSP
ON/OFF
MODE
BASS BOOST EFFECT
1
TREBLE
ANALOG/DIGITAL SLEEP
INPUT
+ CENTER –
2
3
MENU
TEST
4
+ REAR•L –
5
6
ENTER
AUDIO/VIDEO CONTROL RECEIVER
– REAR•R +
SOUND
7/P
8
9
FM/AM TUNING
CATV/DBS
CONTROL
TV/VIDEO
+
TUNING
−
REC
PAUSE
FM/AM PRESET
FM MODE
EON
– SUB WOOFER +
MUTING
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
PTY SEARCH
TA/NEWS/INFO
DISPLAY MODE
COMPULINK
Remote
STANDBY
MEMORY
MASTER VOLUME
STANDBY/ON
D I G I T A L
SURROUND
D I G I T A L
−
SURROUND ON/OFF
PLAY
INPUT
ANALOG/DIGITAL
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
TV SOUND/DBS
INPUT ATT
/REW PAUSE
FF/
SOURCE NAME
DSP MODE
PTY– PTY SEARCH PTY+
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
PHONO
CD
TAPE/CDR
D I G I T A L
FM/AM
SOURCE NAME
STOP CONTROL
DISPLAY
PHONES
RM-SRX7010R
A/V CONTROL RECEIVER
INSTRUCTIONS
For Customer Use:
Enter below the Model No. and Serial
No. which are located either on the rear,
bottom or side of the cabinet. Retain this
information for future reference.
Model No.
Serial No.
LVT0579-005A
[B]
RX-7010&7012R[B]COVER_f
1
01.1.9, 5:21 PM
Warnings, Cautions and Others
IMPORTANT for the U.K.
DO NOT cut off the mains plug from this equipment. If the plug
fitted is not suitable for the power points in your home or the
cable is too short to reach a power point, then obtain an
appropriate safety approved extension lead or consult your
dealer.
BE SURE to replace the fuse only with an identical approved
type, as originally fitted.
If nonetheless the mains plug is cut off ensure to remove the
fuse and dispose of the plug immediately, to avoid a possible
shock hazard by inadvertent connection to the mains supply.
If this product is not supplied fitted with a mains plug then follow
the instructions given below:
IMPORTANT.
DO NOT make any connection to the terminal which is marked
with the letter E or by the safety earth symbol or coloured green
or green-and-yellow.
The wires in the mains lead on this product are coloured in
accordance with the following code:
Blue :
Neutral
Brown : Live
As these colours may not correspond with the coloured
markings identifying the terminals in your plug proceed as
follows:
The wire which is coloured blue must be connected to the
terminal which is marked with the letter N or coloured black.
The wire which is coloured brown must be connected to the
terminal which is marked with the letter L or coloured red.
IF IN DOUBT - CONSULT A COMPETENT ELECTRICIAN.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
Caution ––
switch!
Disconnect the mains plug to shut the power off completely.
The
switch in any position does not disconnect the mains
line. The power can be remote controlled.
CAUTION
• Do not block the ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get
out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems must
be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not use this apparatus in a bathroom or places with
water. Also do not place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases,
potted plants, cups, etc.) on top of this apparatus.
G-1
RX-7010&7012R[B]SAFETY_f
1
01.1.9, 5:21 PM
SAFETY INSTRUCTIONS
“SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT”
This equipment has been disigned and manufactured to meet international safety standards but, like any electrical equipment, care must be
taken if you are to obtain the best results and safety is to be assured.
Do read the operating instructions before you attempt to use the equipment.
Do ensure that all electrical connections (including the mains plug, extension leads and interconnections between pieces of equipment) are
properly made and in accordance with the manufacturer’s instructions. Switch off and withdraw the mains plug when making or changing
connections.
Do consult your dealer if you are ever in doubt about the installation, operation or safety of your equipment.
Do be careful with glass panels or doors on equipment.
DON’T continue to operate the equipment if you are in any doubt about it working normally, or if it is damaged in any way–switch off, withdraw
the mains plug and consult your dealer.
DON’T remove any fixed cover as this may expose dangerous voltages.
DON’T leave equipment switched on when it is unattended unless it is specifically stated that it is designed for unattended operation or has
a standby mode.
Switch off using the switch on the equipment and make sure that your family know how to do this.
Special arrangements may need to be made for infirm or handicapped people.
DON’T use equipment such as personal stereos or radios so that you are distracted from the requirements of traffic safety. It is illegal to watch
television whilst driving.
DON’T listen to headphones at high volume as such use can permanently damage your hearing.
DON’T obstruct the ventilation of the equipment, for example with curtains or soft furnishings.
Overheating will cause damage and shorten the life of the equipment.
DON’T use makeshift stands and NEVER fix legs with wood screws — to ensure complete safety always fit the manufacturer’s approved
stand or legs with the fixings provided according to the instructions.
DON’T allow electrical equipment to be exposed to rain or moisture.
ABOVE ALL
— NEVER let anyone, especially children, push anything into holes, slots or any other opening in the case -this could result in a fatal
electrical shock.;
— NEVER guess or take chances with electrical equipment of any kind — it is better to be safe than sorry!
Caution: Proper Ventilation
To avoid risk of electric shock and fire and to protect from damage.
Locate the apparatus as follows:
Front:
No obstructions open spacing.
Sides:
No obstructions in 10 cm from the sides.
Top:
No obstructions in 10 cm from the top.
Back:
No obstructions in 15 cm from the back
Bottom:
No obstructions, place on the level surface.
In addition, maintain the best possible air circulation as illustrated.
Spacing 15 cm or more
Front
RX-7010RBK/
RX-7012RSL
Wall or obstructions
Stand height 15 cm or more
Floor
G-2
RX-7010&7012R[B]SAFETY_f
2
01.1.9, 5:21 PM
Table of Contents
Parts Identification ...................................... 2
Getting Started ........................................... 3
Before Installation ...................................................................... 3
Checking the Supplied Accessories ........................................... 3
Connecting the FM and AM (MW/LW) Antennas ..................... 3
Connecting the Speakers ............................................................ 4
Connecting Audio/Video Components ....................................... 5
Connecting the Power Cord ....................................................... 9
Putting Batteries in the Remote Control .................................... 9
Basic Operations ....................................... 10
Turning the Power On and Off (Standby) ................................ 10
Selecting the Source to Play ..................................................... 10
Adjusting the Volume ............................................................... 11
Selecting the Front Speakers .................................................... 11
Muting the Sound ..................................................................... 12
Reinforcing the Bass ................................................................ 12
Adjusting the Tone ................................................................... 12
Attenuating the Input Signal .................................................... 12
Adjusting the Subwoofer Output Level .................................... 12
Using the DVD MULTI Playback Mode .......... 30
Activating the DVD MULTI Playback Mode .......................... 30
COMPU LINK Remote Control System ......... 31
Operating JVC’s Audio/Video Components ... 32
Operating Audio Components .................................................. 32
Operating Video Components .................................................. 34
Operating Other Manufacturers’ Video
Equipment ............................................ 35
Troubleshooting ......................................... 39
Specifications ............................................ 40
Basic Settings ........................................... 13
Recording a Source .................................................................. 13
Adjusting the Front Speaker Output Balance ........................... 13
Changing the Source Name ...................................................... 13
Setting the Subwoofer Information .......................................... 14
Setting the Speakers for the DSP Modes ................................. 14
Digital Input (DIGITAL IN) Terminal Setting ......................... 16
Selecting the Analog or Digital Input Mode ............................ 16
Storing the Basic Settings and Adjustments ............................. 17
Using the Sleep Timer .............................................................. 17
Receiving Radio Broadcasts ........................ 18
Tuning in Stations Manually .................................................... 18
Using Preset Tuning ................................................................. 18
Selecting the FM Reception Mode ........................................... 19
Using the RDS (Radio Data System) to Receive FM Stations . 20
Searching for a Program by PTY Codes .................................. 20
Switching to a Broadcast Program of
Your Choice Temporarily ................................................... 21
Using the DSP Modes ................................ 23
What are the DSP Modes? ........................................................ 23
Reproducing the Sound Field .................................................... 24
Available DSP Modes According to the Speaker Arrangement .. 25
Adjusting the Surround Modes ................................................ 26
Adjusting the DAP Modes ....................................................... 28
Activating the DSP Modes ....................................................... 29
1
EN01_09.RX-7010&7012R[B]_f
1
01.1.9, 5:21 PM
Parts Identification
Become familiar with the buttons and controls on the receiver before use.
Refer to the pages in parentheses for details.
1
2
3
4 5
FM/AM TUNING
FM/AM PRESET
6
7
8
AUDIO/VIDEO CONTROL RECEIVER
EON
FM MODE
PTY SEARCH
TA/NEWS/INFO
DISPLAY MODE
COMPULINK
Remote
STANDBY
MEMORY
MASTER VOLUME
STANDBY/ON
D I G I T A L
D I G I T A L
SURROUND
INPUT
ANALOG/DIGITAL
SURROUND ON/OFF
BASS BOOST
ADJUST SETTING
DVD MULTI
DVD
VCR
PHONO
CD
TAPE/CDR
TV SOUND/DBS
INPUT ATT
SOURCE NAME
DSP MODE
CONTROL
DOWN
UP
SPEAKERS ON/OFF
1
2
FM/AM
SOURCE NAME
PHONES
p q
9
w
1
a
2
3
4
5
6
b
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MUILTI
CD
FM/AM
VCR
TAPE/CDR
PHONO
+
−
+
TV/DBS
−
BASS
SURROUND
DSP
ON/OFF
MODE
TREBLE
ANALOG/DIGITAL SLEEP
INPUT
– CENTER +
BASS BOOST EFFECT
1
7
2
p
q
w
e
r
t
y
u
3
MENU
– REAR • L +
TEST
4
5
6
ENTER
8
9
e
SOUND
– REAR • R +
7/P
8
CATV/DBS
CONTROL
TV/VIDEO
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
−
−
REC
PAUSE
i
−
o
;
PLAY
+
TUNING
9
– SUB WOOFER +
MUTING
/REW PAUSE
FF/
a
PTY– PTY SEARCH PTY+
STOP CONTROL
DISPLAY
s
RM-SRX7010R
A/V CONTROL RECEIVER
r
t
y
u
i
o
;
Remote Control
Front Panel
1 Display window (See below) *
a: Remote control operation mode indicator
b: Signal transmission indicator
Lights up when transmitting the remote
control signal.
2
buttons (10, 34 – 38)
CATV/DBS, VCR, TV, AUDIO
3 Source selecting buttons (10, 17) *
DVD, DVD MULTI, CD, FM/AM, TV/DBS, VCR,
TAPE/CDR, PHONO
4 BASS +/– buttons (12)
5 SURROUND ON/OFF button (26, 29)
6 DSP MODE button (27 – 29)
7 BASS BOOST button (12)
8 SOUND button (12, 26 – 28, 30) *
9 MUTING button (12)
p CATV/DBS CONTROL button (36) *
q TV/VIDEO button (34, 35)
w CH(annel) +/– buttons (34 – 37)
e TUNING +/– buttons (18)
r REC PAUSE button (33, 34, 37)
t TREBLE +/– buttons (12)
y SLEEP button (17)
u ANALOG/DIGITAL INPUT button (17)
i • 10 keys for selecting preset channels (19)
• 10 keys for adjusting sound (12, 19, 26 – 28, 30)
• 10 keys for operating audio/video components
(32 – 38)
o TV VOL(ume) +/– buttons (34, 35)
; VOLUME +/– buttons (11)
a • RDS operation buttons (20 – 21)
PTY SEARCH, PTY +/–, DISPLAY
• Operating buttons for audio/video components
(32 – 34, 37, 38)
s CONTROL button (33, 34) *
1 STANDBY/ON
button and STANDBY
lamp (10)
2 FM/AM TUNING 5/∞ buttons (18)
3 FM/AM PRESET 5/∞ buttons (18)
4 FM MODE button (19)
5 MEMORY button (18)
6 Display (10)
7 Remote sensor (9)
8 RDS operation buttons (20 – 21)
EON, PTY SEARCH, TA/NEWS/INFO,
DISPLAY MODE
9 PHONES jack (11)
p SURROUND ON/OFF button (26, 29)
q DSP MODE button (27 – 29)
w INPUT ANALOG/DIGITAL button (17)
INPUT ATT button (12)
e SPEAKERS ON/OFF 1 button (11)
SPEAKERS ON/OFF 2 button (11)
r BASS BOOST button (12)
t Source selecting buttons (10, 16)
DVD MULTI, DVD, VCR, TV SOUND/DBS,
PHONO, CD, TAPE/CDR, FM/AM
y SOURCE NAME buttons (13)
• The TV SOUND/DBS button and TAPE/CDR
button also function as the SOURCE NAME
button.
u ADJUST button (12, 13, 26 – 28, 30)
i CONTROL UP 5/DOWN ∞ buttons
o SETTING button (14 – 16)
; MASTER VOLUME control (11)
* When you press one of these buttons, the remote control operation mode appears on
the display window for about 10 seconds.
Ex.: When you press CD button
Buttons on the Remote Control
FM/AM
CD
PHONO
TAPE/CDR
DVD
DVD MULTI
Remote Control Operation Mode
TUNER
CD
PHONO
TAPE
DVD
DVD
Buttons on the Remote Control
TV/DBS
VCR
CATV/DBS CONTROL
CONTROL
SOUND
Remote Control Operation Mode
TV
VCR
DBS
Current setting or VCR or TAPE
or CDDSC
SOUND
2
EN01_09.RX-7010&7012R[B]_f
2
01.1.9, 5:22 PM
Getting Started
This section explains how to connect audio/video components and speakers to the receiver, and how to connect the
power supply.
Before Installation
Connecting the FM and AM (MW/LW)
Antennas
General
• Be sure your hands are dry.
• Turn the power off to all components.
• Read the manuals supplied with the components you are going to
connect.
FM Antenna Connections
A
Locations
B
A
NN
TE
AN
75
FMAXIAL
• Install the receiver in a location that is level and protected from
moisture.
• The temperature around the receiver must be between –5˚C and
35˚C (23˚F and 95˚F).
• Make sure there is good ventilation around the receiver. Poor
ventilation could cause overheating and damage the receiver.
ANTENNA
• Remote Control (1)
• Batteries (2)
AM
T
EX
Extend the supplied FM antenna horizontally.
FM 75
• Do not insert any metal object into the receiver.
• Do not disassemble the receiver or remove screws, covers, or
cabinet.
• Do not expose the receiver to rain or moisture.
Check to be sure you have all of the following items, which are
supplied with the receiver.
The number in the parentheses indicates quantity of the pieces
supplied.
AMP
O
LO
FM Antenna
Handling the receiver
Checking the Supplied Accessories
75
FMAXIAL
CO
AM
T
EX
AMP
O
LO
A
NN
TE
AN
CO
COAXIAL
AM
LOOP
Outdoor FM Antenna Cable
AM
EXT
A. Using the Supplied FM Antenna
The FM antenna provided can be connected to the FM 75 Ω
COAXIAL terminal as temporary measure.
• AM (MW/LW) Loop Antenna (1)
B. Using the Standard Type Connector (Not Supplied)
A standard type connector (IEC or DIN45325) should be
connected to the FM 75 Ω COAXIAL terminal.
• FM Antenna (1)
Note:
If anything is missing, contact your dealer immediately.
If reception is poor, connect the outdoor antenna.
Before attaching a 75 Ω coaxial cable (the kind with a round wire
going to an outdoor antenna), disconnect the supplied FM antenna.
3
EN01_09.RX-7010&7012R[B]_f
3
01.1.9, 5:22 PM
AM (MW/LW) Antenna Connections
Snap the tabs on the loop into the
slots of the base to assemble the
AM (MW/LW) loop.
ANTENNA
FM 75
COAXIAL
Basic connecting procedure
1
1
RIG
AM (MW/LW) Loop Antenna
AM
EXT
1
RIG
HT
AM
LOOP
4
3
2
1
RIG
HT
HT
1 Cut, twist and remove the insulation at the end of
each speaker signal cable (not supplied).
2 Turn the knob counterclockwise.
2
1
3
3 Insert the speaker signal cable.
4 Turn the knob clockwise.
Connecting the front speakers
Outdoor single vinyl-covered wire (not supplied)
You can connect two pairs of front speakers (one pair to the FRONT
SPEAKERS 1 terminals, and another pair to the FRONT
SPEAKERS 2 terminals).
Turn the loop until you have the best reception.
1
Notes:
• If the AM (MW/LW) loop antenna wire is covered with
vinyl, remove the vinyl by twisting it as shown in the
diagram.
• Make sure the antenna conductors do not touch any
other terminals, connecting cords and power cord. This could
cause poor reception.
• If reception is poor, connect an outdoor single vinyl-covered wire to
the AM EXT terminal. (Keep the AM (MW/LW) loop antenna
connected.)
2
Right speaker
Right speaker
Connecting the Speakers
You can connect the following speakers:
• Two pairs of front speakers to produce normal stereo sound.
• One pair of rear speakers to enjoy the surround effect.
• One center speaker to produce more effective surround effect (to
emphasize human voices).
• One subwoofer to enhance the bass.
IMPORTANT:
After connecting the speakers listed above, set the speaker
setting information properly to obtain the best possible DSP
effect. For details, see page 14.
1
FRONT
SPEAKERS
2
+
FRONT
SPEAKERS
1
+
–
–
RIGHT
RIGHT
FRONT
SPEAKERS
2
LEFT
LEFT
For each speaker (except for a subwoofer), connect the (+) and (–)
terminals on the rear panel to the (+) and (–) terminals marked on
the speakers. For connecting a subwoofer, see page 5.
Left speaker
CAUTION:
Left speaker
Use speakers with the SPEAKER IMPEDANCE indicated by the
speaker terminals.
4
EN01_09.RX-7010&7012R[B]_f
4
01.1.9, 5:22 PM
About the speaker impedance
Connecting the subwoofer speaker
The required speaker impedance of the front speakers does differ
depending on whether both the FRONT SPEAKERS 1 and FRONT
SPEAKERS 2 terminals are used or only one of them is used.
You can enhance the bass by connecting a subwoofer.
Connect the input jack of a powered subwoofer to the
SUBWOOFER OUT jack on the rear panel, using a cable with RCA
pin plugs (not supplied).
CASE 1
When you connect only one pair of front speakers
Front
speaker
1
Front
speaker
1
SUBWOOFER
OUT
Powered subwoofer
Connecting Audio/Video Components
Use front speakers with 8 Ω – 16 Ω impedance.
CASE 2
When you connect two pairs of front speakers
Front
speaker
2
Front
speaker
2
Front
speaker
1
Front
speaker
1
You can connect the following audio/video components to this
receiver. Refer also to the manuals supplied with your components.
Audio Components
• Turntable
• CD player*
• Cassette deck
or CD recorder*
•
•
•
•
Video Components
DVD player*
TV*
DBS tuner*
VCR
* You can connect these components using the methods described in
“Analog connections” (below) or in “Digital connections” (see page
8).
Analog connections
Audio component connections
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, and the red plug to the
audio right jack.
Use front speakers 16 Ω – 32 Ω impedance.
CAUTION:
Connecting the rear and center speakers
Connect rear speakers to the REAR SPEAKERS terminals and a
center speaker to the CENTER SPEAKER terminals.
If you connect a sound-enhancing device such as a graphic equalizer
between the source components and this receiver, the sound output
through this receiver may be distorted.
Turntable
If an earth cable is provided for your
turntable, connect the cable to the
AM (H) terminal on the rear panel.
Center
speaker
CENTER
SPEAKER
Turntable
REAR
SPEAKERS
PHONO
+
Left rear
speaker
CD
Right rear
speaker
To audio
output
OUT
(REC)
TAPE
CDR
–
RIGHT
LEFT
Ex.: This connection is for the
turntable with an MM (movingmagnet) type cartridge.
IN
(PLAY)
OUT
(REC)
VCR
IN
(PLAY)
Note:
Any turntables incorporating a small-output cartridge
such as an MC
TV
(moving-coil) type must be connected to this SOUND
receiver
through a
DBS
commercial head amplifier or step-up transformer. Direct
RIGHT connection
LEFT
may result in insufficient volume.
AUDIO
5
EN01_09.RX-7010&7012R[B]_f
5
01.1.9, 5:22 PM
Video component connections
CD player
Use the cables with RCA pin plugs (not supplied).
Connect the white plug to the audio left jack, the red plug to the
audio right jack, and the yellow plug to the video jack.
If your video components have S-video (Y/C-separation) terminals,
connect them using S-video cables (not supplied). Connecting these
video components through the S-video input/output terminals will
give you better picture playback (or recording) quality.
PHONO
CD player
CD
OUT
(REC)
TAPE
CDR
To audio output
IN
(PLAY)
IMPORTANT:
OUT
(REC)
VCR
Cassette deck or CD recorder
Cassette deck
To audio input
To audio output
PHONO
CD
This receiver is equipped with both the composite video and S-video
input/output terminals for connecting video components.
You do not have to connect both the composite video and S-video
terminals.
However, remember that the video signals from the composite
video input terminals are output only through the composite
video output terminals, while the ones from the S-video input
terminals are output only through the S-video output terminals.
Therefore, if a recording video component and a playing video
component are connected to the receiver through the different video
terminals, you cannot record the picture from the playing component
on the recording component. In addition, if the TV and a playing video
component are connected to the receiver through the different video
terminals, you cannot view the playback picture from the playing
component on the TV.
OUT
(REC)
VCR
TAPE
CDR
IN
(PLAY)
S-VHS (or VHS) VCR
A
C D
OUT
(REC)
VCR
B
IN
(PLAY)
TV
SOUND
DBS
E F
PHONO
RIGHT
LEFT
CD
AUDIO
MONITOR
OUT
OUT
(REC)
To audio input
TAPE
CDR
To audio output
CD recorder
Note:
You can connect either a cassette deck or a CD recorder to the TAPE/
CDR jacks. When connecting a CD recorder to the TAPE/CDR jacks,
change the source name, which will be shown on the display when
selected as the source, to “CDR.” See page 13 for details.
IN
(PLAY)
DVD
OUT
(REC)
OUT
(REC)
VCR
VCR
If your audio components have a COMPU LINK jack
See also page 31 for detailed information about the connection and
the COMPU LINK remote control system.
IN
(PLAY)
IN
(PLAY)
TV
SOUND
DBS
DBS
RIGHT
LEFT
AUDIO
Å
ı
Ç
Î
‰
Ï
VIDEO
To left/right channel audio output
To left/right channel audio input
To S-video output
To composite video output
To composite video input
To S-video input
6
EN01_09.RX-7010&7012R[B]_f
6
01.1.9, 5:22 PM
DVD player
TV and/or DBS tuner
• When you connect the DVD player with stereo output jacks:
To S-video input
A
B C
DVD player
To composite video input
DVD
PHONO
Connect the TV to the MONITOR
OUT jack to view the playback
CD
picture from the other connected
video components.
OUT
(REC)
MONITOR
OUT
AUDIO
RIGHT
MONITOR
OUT
DVD
SUB
WOOFER
DVD
IN
(PLAY)
OUT
(REC)
CENTER
VCR
REAR
OUT
(REC)
OUT
(REC)
IN
(PLAY)
RIGHT
LEFT
VCR
VCR
To audio
output
DVD
FRONT
TAPE
CDR
TV
LEFT
IN
(PLAY)
IN
(PLAY)
TV
SOUND
DBS
DBS
RIGHT
DBS
SUBWOOFER
OUT
LEFT
Å To front left/right channel audio output (or to audio mixed
output if necessary)
ı To S-video output
Ç To composite video output
VIDEO
AUDIO
VIDEO
When connecting the TV to the AUDIO jacks (TV
SOUND/DBS), DO NOT connect the TV’s video
output to these video input terminals.
• When you connect the DVD player with its analog discrete output
(5.1 CH reproduction) jacks:
E
A
C
DVD player
DVD
VCR
VCR
IN
(PLAY)
IN
(PLAY)
TV
SOUND
DBS
F
D
MONITOR
OUT
DBS
AUDIO
RIGHT
RIGHT
To audio
DBS tuner
output
B
LEFT
LEFT
AUDIO
VIDEO
DVD
FRONT
DVD
SUB
WOOFER
DBS
CENTER
VCR
REAR
IN
(PLAY)
To composite video output
RIGHT
LEFT
DBS
To S-video output
Note:
SUBWOOFER
OUT
When connecting the DBS tuner to the TV SOUND/DBS jacks,
change the source name, which will be shown on the display when
selected as the source, to “DBS.” See page 13 for details.
Å
ı
Ç
Î
‰
Ï
To center channel audio output
To subwoofer audio output
To S-video output
To front left/right channel audio output
To rear left/right channel audio output
To composite video output
7
EN01_09.RX-7010&7012R[B]_f
7
OUT
(REC)
01.1.9, 5:22 PM
VIDEO
Digital connections
Notes:
This receiver is equipped with four DIGITAL IN terminals — one
digital coaxial terminal and three digital optical terminals, and one
DIGITAL OUT terminal.
You can connect any digital equipment such as —
• DBS tuner,
• Digital TV broadcast tuner,
• DVD player,
• CD player, and
• CD recorder.
• When shipped from the factory, the DIGITAL IN terminals have
been set for use with the following components.
– DIGITAL 1 (coaxial): For DVD player
– DIGITAL 2 (optical): For CD player
– DIGITAL 3 (optical): For digital TV broadcast tuner
– DIGITAL 4 (optical): For CD recorder
• When you want to operate the CD player or CD recorder using the
COMPU LINK remote control system, connect the target
component also as described in “Analog connections” (see page 6).
IMPORTANT:
• When connecting the DVD player, digital TV broadcast tuner or DBS
tuner using the digital terminals, you also need to connect it to the
video jack (either composite video terminal or S-video terminal) on
the rear. Without connecting it to the video jack, you can view no
playback picture.
• After connecting the components using the DIGITAL IN terminals,
set the following correctly if necessary.
– Set the digital input (DIGITAL IN) terminal setting correctly. For
details, see “Digital Input (DIGITAL IN) Terminal Setting” on page
16.
– Select the digital input mode correctly. For details, see “Selecting
the Analog or Digital Input Mode” on page 16.
Digital output terminal
CD recorder, etc.
Digital optical cable (not supplied)
between digital optical terminals
Digital input terminals
Digital TV
When the digital recording
equipment such as a CD recorder
has a digital optical input terminal,
connecting it to the DIGITAL OUT
terminal enables you to perform
digital-to-digital recording.
DVD player
DVD
CD player
CD recorder
DOLBY DIGITAL/PCM
/DTS
DIGITAL OUT
Digital coaxial cable (not supplied)
between digital coaxial terminals
Digital optical cable (not supplied)
between digital optical terminals
When the component has a digital
coaxial output terminal, connect it to the
DIGITAL 1 (DVD) terminal, using the
digital coaxial cable (not supplied).
When the component has a digital
optical output terminal, connect it to the
DIGITAL 2 (CD), DIGITAL 3 (TV), or
DIGITAL 4 (CDR) terminal, using the
digital optical cable (not supplied).
Before connecting a digital
optical cable, unplug the
protective plug.
DIGITAL 1
(DVD)
DIGITAL 2 ( CD )
DIGITAL 3 ( TV )
DIGITAL 4 (CDR)
DIGITAL IN
8
EN01_09.RX-7010&7012R[B]_f
8
01.1.9, 5:22 PM
Connecting the Power Cord
Before plugging the receiver into an AC outlet, make sure that all
connections have been made.
Putting Batteries in the Remote Control
Before using the remote control, put two supplied batteries first.
When using the remote control, aim the remote control directly at
the remote sensor on the receiver.
Plug the power cord into an AC outlet.
Keep the power cord away from the connecting cables and the
antenna. The power cord may cause noise or screen interference. We
recommend that you use a coaxial cable to connect the antenna,
since it is well-shielded against interference.
1
Note:
The preset settings such as preset channels and sound adjustment
may be erased in a few days in the following cases:
–When you unplug the power cord.
–When a power failure occurs.
CAUTIONS:
• Do not touch the power cord with wet hands.
• Do not pull on the power cord to unplug the cord. When
unplugging the cord, always grasp the plug so as not to damage
the cord.
2
R6P(SUM-3)/AA(15F)
3
1. On the back of the remote control, remove the
battery cover.
2. Insert batteries. Make sure to match the polarity:
(+) to (+) and (–) to (–).
3. Replace the cover.
If the range or effectiveness of the remote control decreases, replace
the batteries. Use two R6P(SUM-3)/AA(15F) type dry-cell batteries.
CAUTION:
Follow these precautions to avoid leaking or cracking cells:
• Place batteries in the remote control so they match the polarity:
(+) to (+) and (–) to (–).
• Use the correct type of batteries. Batteries that look similar may
differ in voltage.
• Always replace both batteries at the same time.
• Do not expose batteries to heat or flame.
9
EN01_09.RX-7010&7012R[B]_f
9
01.1.9, 5:22 PM
Basic Operations
The following operations are commonly used when you play any sound source.
Turning the Power On and Off (Standby)
On the front panel:
To turn on the power, press STANDBY/ON
. The STANDBY lamp goes off. The name
of the current source (or station frequency)
appears on the display.
STANDBY
STANDBY/ON
Current source name appears
SPK 1
L
ANALOG
R
VOLUME
Current volume level is shown here
To turn off the power (into standby mode),
press STANDBY/ON
again.
The STANDBY lamp lights up. A small amount
of power is consumed in standby mode. To turn
the power off completely, unplug the AC power
cord.
STANDBY
STANDBY/ON
DVD MULTI
Select the DVD player for viewing the digital
video disc using the analog discrete output mode
(5.1 CH reproduction).
To enjoy the DVD MULTI playback, see page
30.
DVD
Select the DVD player.
VCR
Select the video component connected to the
VCR jacks.
TV SOUND/DBS Select TV sounds (or the DBS tuner).
PHONO*
Select the turntable.
CD*
Select the CD player.
TAPE/CDR*
Select the cassette deck (or the CD recorder).
FM/AM*
Select an FM or AM (MW/LW) broadcast.
• Each time you press the button, the band
alternates between FM and AM (MW/LW).
Notes:
• When connecting a CD recorder (to the TAPE/CDR jacks), and a
DBS tuner (to the TV SOUND/DBS jacks), change the source name
shown on the display. For details, see page 13.
• When you press one of the source selecting buttons on the remote
control marked above with an asterisk (*), the receiver
automatically turns on.
Signal and speaker indicators on the display
From the remote control:
To turn on the power, press AUDIO
.
The STANDBY lamp goes off. The name of
the current source (or station frequency)
appears on the display.
The signal indicators light up in the following cases:
• Only the indicators for the incoming signals light up.
• When analog input is selected, “L” and “R” always light up.
• When “DVD MULTI” is selected as the source, “L,” “C,” “R,”
“LFE,” “LS” and “RS” light up.
The speaker indicators light up only —:
• When the corresponding speaker is activated.
AND
• When the corresponding speaker is required for the DSP mode
selected currently.
AUDIO
To turn off the power (into standby mode), press
again. The STANDBY lamp lights up.
AUDIO
Selecting the Source to Play
Signal indicators light up in
red:
Press one of the source selecting buttons.
On the front panel:
DVD MULTI
L
DVD
VCR
CD
TAPE/CDR
R
L
C
R
S.WFR LFE
S.WFR LFE
LS
LS
TV SOUND/DBS
SOURCE NAME
PHONO
C
Speaker indicators light up
in white:
S
RS
S
RS
FM/AM
SOURCE NAME
L:
From the remote control:
DVD
DVD MUILTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
R:
C:
LS:
RS:
S:
LFE:
Selected source name appears
DIGITAL AUTO
ANALOG
LINEAR PCM
DIGITAL
SPK 1 2
L
C
R
BASS BOOST INPUT ATT
S
Notes:
SLEEP
PRO LOGIC DSP H.PHONE AUTO MUTING TUNED STEREO TA NEWS INFO VOLUME
S.WFR LFE
LS
EON RDS
RS
CH-
• When digital input is selected: Lights up when the left
channel signal comes in.
• When analog input is selected: Always lights up.
• When digital input is selected: Lights up when the right
channel signal comes in.
• When analog input is selected: Always lights up.
Lights up when the center channel signal comes in.
Lights up when the left rear channel signal comes in.
Lights up when the right rear channel signal comes in.
Lights up when the monaural rear channel signal comes in.
Lights up when the LFE channel signal comes in.
• When “SUBWOOFER” is set to “YES,” S.WFR lights up.
• When you select “DVD MULTI,” all the signal indicators except “S”
light up.
10
EN10_22.RX-7010&7012R[B]_f
10
01.1.9, 5:23 PM
Selecting different sources for picture and
sound
You can watch picture from a video component while listening to
sound from another component.
Selecting the Front Speakers
On the front panel ONLY:
When you have connected two pairs of the front speakers, you can
select which to use.
Press one of the audio source selecting buttons — PHONO, CD,
TAPE/CDR, FM/AM, TV SOUND/DBS* (or TV/DBS on the
remote control), while viewing the picture from a video component
such as the VCR, DVD player, or DBS tuner, etc.
Notes:
• Once you have selected a video source, pictures of the selected
source are sent to the TV until you select another video source.
* The TV SOUND/DBS (or TV/DBS on the remote control) only
works for selecting “DBS” as the source but not for selecting “TV
SOUND (or TV on the remote control).” When you use the DBS
tuner, change the source name correctly (see page 13).
Adjusting the Volume
On the front panel:
To increase the volume, turn MASTER
VOLUME clockwise.
To decrease the volume, turn it
counterclockwise.
• When you turn MASTER VOLUME
rapidly, the volume level also changes rapidly.
• When you turn MASTER VOLUME slowly,
the volume level also changes slowly.
From the remote control:
To increase the volume, press VOLUME +.
To decrease the volume, press VOLUME –.
MASTER VOLUME
SPEAKERS ON/OFF
1
2
To use the speakers connected to the FRONT SPEAKERS 1
terminals, press SPEAKERS ON/OFF 1 so that the SPK 1 indicator
lights up on the display. (Make sure that the SPK 2 is not on the
display.)
To use the speakers connected to the FRONT SPEAKERS 2
terminals, press SPEAKERS ON/OFF 2 so that the SPK 2 indicator
lights up on the display. (Make sure that the SPK 1 is not on the
display.)
To use both sets of the speakers, press SPEAKERS ON/OFF 1 and
2 so that the SPK 1 and SPK 2 indicators light up on the display.
To use neither sets of the speakers, press SPEAKERS ON/OFF 1
and 2 so that the SPK 1 and SPK 2 indicators disappear from the
display.
Notes:
• If you select any of the DSP modes while using both the speakers
connected to the FRONT SPEAKERS 1 and 2 terminals, the
speakers connected to the FRONT SPEAKERS 2 terminals are
deactivated.
• While the DSP MODE is in use, you can only select either the
speakers connected to the FRONT SPEAKERS 1 or 2 terminals.
+
VOLUME
−
CAUTION:
Always set the volume to the minimum before starting any source. If
the volume is set at its high level, the sudden blast of sound energy
can permanently damage your hearing and/or ruin your speakers.
Note:
The volume level can be adjusted within the range of “0” (minimum) to
“80” (maximum).
Listening only with headphones
You must turn off both pairs of speakers when you listen with
headphones.
1. Connect a pair of headphones to the PHONES jack on the front
panel.
2. Press SPEAKERS ON/OFF 1 and SPEAKERS ON/OFF 2 so
that neither the SPK 1 nor SPK 2 indicator appears on the
display.
This cancels the DSP mode currently selected, and activates the
HEADPHONE mode (see below).
• “HEADPHONE” appears and H. PHONE indicator lights up
on the display.
HEADPHONE mode:
This mode can reproduce the LFE channel signals, mixing them
with the front channel signals. So you will not miss the
subwoofer sounds even if you listen to a source using the
headphones.
Notes:
• While in the HEADPHONE mode, you cannot use any DSP modes
(see page 23.)
• Activating the speaker cancels the HEADPHONE mode and turns
on the DSP mode previously selected.
CAUTION:
Be sure to turn down the volume before connecting or putting on
headphones, as high volume can damage both the headphones and
your hearing.
11
EN10_22.RX-7010&7012R[B]_f
11
01.1.9, 5:23 PM
Muting the Sound
From the remote control:
From the remote control ONLY:
Press MUTING to mute the sound
through all speakers and headphones
connected.
MUTING
“MUTING” appears on the display and the
volume turns off (the volume level indicator goes
off).
Press BASS +/– or TREBLE +/– to
adjust the bass or treble sound level
(+10 dB to –10 dB).
−
BASS
−
TREBLE
+
+
Attenuating the Input Signal
To restore the sound, press MUTING again so that “OFF” appears
on the display.
• Turning MASTER VOLUME on the front panel or pressing
VOLUME +/– on the remote control also restores the sound.
When the input level of the playing source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
On the front panel ONLY:
Reinforcing the Bass
Press and hold INPUT ATT so that
the INPUT ATT indicator lights up
on the display.
You can boost the bass level.
Press BASS BOOST on the front panel or on the
remote control to select the bass boost function.
BASS BOOST
INPUT
ANALOG/DIGITAL
INPUT ATT
• Each time you press and hold the button, the
Input Attenuator mode turns on (“INPUT ATT
ON”) or off (“INPUT NORMAL”).
BASS BOOST
Notes:
On the front panel
On the remote
control
• Each time you press the button, the bass boost function turns
on (“BASSBOOST ON”) and off (“BASSBOOST OFF”).
– Select “BASSBOOST ON” to activate the bass boost function.
The BASS BOOST indicator lights up on the display.
– Select “BASSBOOST OFF” to cancel it.
The indicator goes off.
Note:
This function affects the front speaker sounds only.
You can adjust the bass and treble sounds as you like.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel:
ADJUST SETTING
• Select “BASS” to adjust the bass sound level.
• Select “TREBLE” to adjust the treble sound level.
2. Press CONTROL UP 5/DOWN ∞
to adjust the bass or treble sound
level (+10 dB to –10 dB).
• Each time you press the button, the
sound level changes by ± 2 steps.
Adjusting the Subwoofer Output Level
You can adjust the subwoofer output level if you have selected
“YES” for the “SUBWOOFER” (see page 14).
Once it has been adjusted, the receiver memorizes the adjustment.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• When the front speakers are all deactivated, the subwoofer level
cannot be adjusted.
Adjusting the Tone
1. Press ADJUST repeatedly until
“BASS” or “TREBLE” appears on
the display.
• This function is available only for the sources connected using the
analog terminals.
• This function takes effect when the DSP mode is in use.
• When selecting “DVD MULTI” as the source, this effect does not
work.
CONTROL
DOWN
UP
On the front panel:
1. Press ADJUST repeatedly until
“SUBWFR LEVEL” appears on
the display.
ADJUST SETTING
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to adjust the subwoofer output
level (+10 dB to –10 dB).
CONTROL
DOWN
UP
From the remote control:
1. Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
2. Press SUBWOOFER +/– to adjust
the subwoofer output level (+10 dB
to –10 dB).
– SUB WOOFER +
0
+10
FM MODE
100+
12
EN10_22.RX-7010&7012R[B]_f
12
01.1.9, 5:23 PM
Basic Settings
Some of the following settings are required after connecting and positioning your speakers in your listening room, while
others will make operations easier.
Recording a Source
Changing the Source Name
For analog-to-analog recording
You can record any analog source through the receiver to —
• the cassette deck (or CD recorder) connected to the TAPE/CDR
jacks, and
• the VCR connected to the VCR jacks
— at the same time.
For digital-to-digital recording
You can record the currently selected digital input through the
receiver to a digital recording device connected to the DIGITAL
OUT terminal.
When you have connected a CD recorder to the TAPE/CDR jacks or
the DBS tuner to the TV SOUND/DBS jacks on the rear panel,
change the source name which will be shown on the display when
you select the CD recorder or DBS tuner as the source.
On the front panel ONLY:
When changing the source name from “TAPE”
to “CDR”:
• Press and hold TAPE/CDR/
TAPE/CDR
SOURCE NAME to assign
“CDR.”
SOURCE NAME
Notes:
• Analog-to-digital and digital-to-analog recordings are not possible.
• The output volume level, bass boost (see page 12), tone
adjustment (see page 12), and DSP modes (see page 23) cannot
affect the recording.
• The test tone signal (see pages 26 and 27) does not come out
through the DIGITAL OUT terminal.
Adjusting the Front Speaker Output
Balance
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speaker output balance.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press ADJUST repeatedly until
“L/R BALANCE” appears on the
display.
When changing the source name from “TV
SOUND” to “DBS”:
• Press and hold TV SOUND/DBS/
TV SOUND/DBS
SOURCE NAME to assign “DBS.”
SOURCE NAME
To change the source name to “TAPE” or “TV SOUND,” repeat
the same procedure above — press and hold TAPE/CDR/SOURCE
NAME to select “TAPE” or TV SOUND/DBS/SOURCE NAME to
select “TV SOUND.”
Note:
Without changing the source name, you can still use the connected
components. However, there may be some inconvenience.
– “TAPE” or “TV SOUND” will appear on the display when you select
the CD recorder or DBS tuner.
– You cannot use the digital input (see page 16) for the CD recorder.
– You cannot use the COMPU LINK remote control system (see page
31) to operate the CD recorder.
ADJUST SETTING
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to adjust the balance.
CONTROL
DOWN
UP
• Pressing CONTROL UP 5 decreases the
left channel output from CNTR (Center)
to –21.
• Pressing CONTROL DOWN ∞ decreases
the right channel output from CNTR
(Center) to –21.
13
EN10_22.RX-7010&7012R[B]_f
13
01.1.9, 5:23 PM
Setting the Subwoofer Information
3. Repeat steps 1 and 2 to select the appropriate
items for the other speakers.
Register whether you have connected a subwoofer or not.
Notes:
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“SUBWOOFER” appears on the
display.
T SETTING
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to register whether you have
connected a subwoofer or not.
Center Delay Time Setting
CONTROL
DOWN
UP
• Each time you press the button, the
subwoofer setting alternates between
“YES” and “NO.”
YES:
Select this when a subwoofer is used.
up on the display (see page 10).
NO:
Select this when no subwoofer is used.
S.WFR
lights
Setting the Speakers for the DSP Modes
To obtain the best possible surround sound of the DSP modes, you
have to register the information about the speakers arrangement after
all connections are completed.
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
Front, Center, and Rear Speaker Setting
Register the sizes of all the connected speakers.
• When you change your speakers, you need to register the
information about the speakers again.
On the front panel ONLY:
1. Press SETTING repeatedly until
“FRONT SPK” (Front Speaker),
“CENTER SPK” (Center
Speaker) or “REAR SPK” (Rear
Speaker) appears on the display.
ST SETTING
CONTROL
DOWN
UP
• Each time you press the button, the display
changes to show the following:
LARGE
SMALL
Register the delay time of the sound from the center speaker,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the center speaker is
equal to that to the front speakers, select 0 msec. As the distance to
the center speaker becomes shorter, the delay time increases.
• 1 msec increase (or decrease) in delay time corresponds to
11 13/16 inches (30 cm) decrease (or increase) in distance.
• When shipped from the factory, delay time is set to 0 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CENTER DELAY” appears on
the display.
T SETTING
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to select the delay time of the
center speaker output.
CONTROL
DOWN
UP
• Press CONTROL UP 5 to increase the delay
time from 0 msec (“C_DELAY 0MS”) to
5 msec (“C_DELAY 5MS”).
• Press CONTROL DOWN ∞ to decrease the
delay time from 5 msec (“C_DELAY 5MS”)
to 0 msec (“C_DELAY 0MS”).
Notes:
• Center delay time is not valid for the DVD MULTI playback mode.
• You cannot adjust the center delay time when you have set
“CENTER SPK” to “NO.”
Rear Delay Time Setting
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to select the appropriate item
about the speaker selected in the
above step.
• Keep the following comment in mind as reference when adjusting.
– If the size of the cone speaker unit built in your speaker is greater
than 4 3/4 inches (12 cm ), select “LARGE,” and if it is smaller
than 4 3/4 inches (12 cm ), select “SMALL.”
• If you have selected “NO” for the subwoofer setting, you can only
select “LARGE” for the front speaker setting.
• If you have selected “SMALL” for the front speaker setting, you
cannot select “LARGE” for the center and rear speaker settings.
NO
LARGE: Select this when the speaker size is relatively large.
Register the delay time of the sound from the rear speakers,
comparing to that of the sound from the front speakers.
If the distance from your listening point to the rear speakers is equal
to that to the front speakers, select 0 msec. As the distance to the
rear speakers becomes shorter, the delay time increases.
• 1 msec increase (or decrease) in delay time corresponds to
11 13/16 inches (30 cm) decrease (or increase) in distance.
• Rear delay time for Dolby Digital and DTS Digital Surround is to
be set to 5 msec.
• When shipped from the factory, delay time is set to 5 msec.
On the front panel ONLY:
1. Press SETTING repeatedly until
“REAR DELAY” appears on the
display.
T SETTING
The display changes to show the current setting.
SMALL: Select this when the speaker size is relatively small.
NO:
Select this when you have not connected a speaker.
(Not selectable for the front speakers)
Continued to the next page.
14
EN10_22.RX-7010&7012R[B]_f
14
01.1.9, 5:23 PM
2. Press CONTROL UP 5/DOWN ∞
to select the delay time of the rear
speaker output.
CONTROL
DOWN
UP
Low Frequency Effect Attenuator Setting
If the bass sound is distorted while playing back a source using
Dolby Digital or DTS Digital Surround, follow the procedure below.
• Press CONTROL UP 5 to increase the delay
time from 0 msec (“R_DELAY 0MS”) to
15 msec (“R_DELAY 15MS”).
• Press CONTROL DOWN ∞ to decrease the
delay time from 15 msec (“R_DELAY 15MS”)
to 0 msec (“R_DELAY 0MS”).
On the front panel ONLY:
1. Press SETTING repeatedly until
“LFE ATT” (Low Frequency
Effect Attenuator) appears on the
display.
T SETTING
The display changes to show the current setting.
Notes:
• Rear delay time is not valid for the DVD MULTI playback mode.
• You cannot adjust the rear delay time when you have set “REAR
SPK” to “NO.”
Crossover Frequency Setting
Small speakers cannot reproduce the bass sound very well. So, if
you have used a small speaker for any of the front, center, and rear
channels, this receiver automatically reallocate the bass elements,
originally assigned to the channel for which you have connected the
small speaker, to another channel (for which you have connected the
large speaker).
To use this function properly, you need to set the crossover
frequency level according to the size of the small speaker connected.
• If you have selected “LARGE” for all speakers (see page 14), this
function is set to “OFF” and cannot be adjusted.
On the front panel ONLY:
1. Press SETTING repeatedly until
“CROSSOVER FRQ” (Crossover
Frequency) appears on the display.
ST SETTING
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to select the crossover frequency
level according to the size of the
small speaker connected.
CONTROL
DOWN
UP
• Each time you press the button, the display changes to show
the following:
80HZ
100HZ
120HZ
2. Press CONTROL UP 5/DOWN ∞
to select the low frequency effect
attenuator level.
CONTROL
DOWN
UP
• Each time you press the button, the display
changes to show the following:
0dB
10dB
0dB:
Normally select this.
10dB:
Select this when the bass sound is distorted.
Notes:
• Low frequency effect attenuator is not valid for the DVD MULTI
playback mode.
• This function takes effect only when the subwoofer (LFE) signals
come in, (with “SUBWOOFER” set to “YES.”)
Dynamic Range Compression Setting
You can compress the dynamic range (difference between maximum
sound and minimum sound) of the reproduced sound. This is useful
when enjoying surround sound at night.
• This function takes effect only when playing back a source using
Dolby Digital.
On the front panel ONLY:
1. Press SETTING repeatedly until
“D_RANGE COMP” (Dynamic
Range Compression) appears on
the display.
ST SETTING
The display changes to show the current setting.
80HZ:
Select this when the cone speaker unit built in the
speaker is about 4 3/4 inches (12 cm).
2. Press CONTROL UP 5/DOWN ∞
to select the appropriate item
about the compression level.
100HZ:
Select this when the cone speaker unit built in the
speaker is about 3 15/16 inches (10 cm).
• Each time you press the button, the display
changes to show the following:
120HZ:
Select this when the cone speaker unit built in the
speaker is about 3 3/16 inches (8 cm).
• Use the following comments as reference when adjusting.
OFF
MID
CONTROL
DOWN
UP
MAX
Note:
OFF:
Crossover frequency is not valid for the DVD MULTI playback mode
and HEADPHONE mode.
Select this when you want to enjoy surround with its
full dynamic range. (No effect applied.)
MID:
Select this when you want to reduce the dynamic
range a little. (Factory setting.)
MAX:
Select this when you want to apply the compression
effect fully. (Useful at night.)
Note:
Dynamic Range Compression is not valid for the DTS Digital
Surround and DVD MULTI playback mode.
15
EN10_22.RX-7010&7012R[B]_f
15
01.1.9, 5:23 PM
Digital Input (DIGITAL IN) Terminal
Setting
When you use the digital input terminals, you have to register what
components are connected to which terminals (DIGITAL IN 1/2/3/4).
Before you start, remember....
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
On the front panel ONLY:
To set the DIGITAL 1 terminal
1. Press SETTING repeatedly until
“COAX DIG IN” appears on the
display.
ST SETTING
When you have connected digital source components, you need to
select the input mode correctly according to the connection you
made.
Before you start, remember...
• The digital input (DIGITAL IN) terminal setting should be
correctly done for the sources you want to select the digital
input mode for. Without setting this digital input terminal
correctly, you cannot change the input mode from analog input to
digital input even if you follow the procedure below.
On the front panel:
The display changes to show the current setting.
2. Press CONTROL UP 5/DOWN ∞
to select the appropriate digital
terminal setting.
Selecting the Analog or Digital Input
Mode
CONTROL
DOWN
UP
• Each time you press the button, the display changes to
show the following:
1 DVD “ 1 CDR “ 1 TV (or 1 DBS*) “ 1 CD “
(back to the beginning)
* If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears (see page 13.)
When the DIGITAL 1 terminal is set, the
DIGITAL 2/3/4 terminal is automatically set as
follows:
1. Press one of the
DVD MULTI
DVD
source selecting
buttons (DVD, TV PHONO
CD
SOUND/DBS, CD,
or TAPE/CDR)*
for which you
want to change the input mode.
VCR
TV SOUND/DBS
SOURCE NAME
TAPE/CDR
FM/AM
SOURCE NAME
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press INPUT ANALOG/DIGITAL
to change the input mode.
• Each time you press the button, the input
mode changes as follows:
INPUT
ANALOG/DIGITAL
INPUT ATT
DIGITAL 3 terminal setting
AUTO
ANALOG
(Digital)
AUTO:
DIGITAL 2 terminal setting
DIGITAL 4 terminal setting
When the DIGITAL 1 is set to “DVD”
2 CD 3 TV (or DBS*) 4 CDR
When the DIGITAL 1 is set to “CDR”
2 DVD 3 CD 4 TV (or DBS*)
When the DIGITAL 1 is set to “TV” or “DBS”
2 DVD 3 CD 4 CDR
When the DIGITAL 1 is set to “CD”
2 DVD 3 TV (or DBS*) 4 CDR
* If you have changed the source name from “TV SOUND” to
“DBS,” “DBS” appears (see page 13.)
Notes:
Select this for the digital input mode. The receiver
automatically detects the incoming signal format.
(The DIGITAL AUTO indicator lights up on the
display, and the digital signal indicator for the
detected signals also light up.)*
ANALOG: Select this for the analog input mode.
* The followings are the analog/digital signal indicators on the
display to indicate what type of the signal comes into the
receiver.
DIGITAL AUTO :
Lights up when “AUTO” is selected as
the digital input mode.
Lights up when the analog input is
ANALOG :
selected.
LINEAR PCM : Lights up when Linear PCM signals
come in.
DIGITAL:
Lights up when Dolby Digital signals
come in.
:
Lights up when DTS Digital Surround
signals come in.
• When shipped from the factory, the DIGITAL IN terminals can be
used as the digital input for the following components.
• DIGITAL 1 (coaxial): For DVD player
• DIGITAL 2 (optical): For CD player
• DIGITAL 3 (optical): For digital TV broadcast tuner
• DIGITAL 4 (optical): For CDR
• When using the DIGITAL 4 terminal for the CD recorder, you need
to select “CDR” as the source name. (See page 13.)
Continued to the next page.
16
EN10_22.RX-7010&7012R[B]_f
16
01.1.9, 5:23 PM
When playing a software encoded with the DTS Digital
Surround, “AUTO” may not work properly and the following
symptoms may occur:
• Sound does not come out at the beginning of playback.
• Noise comes out while using the searching or skipping
function.
In this case, press CONTROL UP 5/
DOWN ∞ to select “DTS” while “AUTO”
is lit on the display.
• Each time you press the button, the input
mode changes as follows:
AUTO
DTS
(Digital)
(Digital)
Storing the Basic Settings and
Adjustments
You can assign and store different sound settings for each different
playing source. By using this function, you do not have to change
the settings every time you change the source. The stored settings
for the newly selected source are automatically recalled.
CONTROL
DOWN
UP
Note:
When you turn off the power or select another source, “DTS”
setting is canceled and the digital input mode is automatically
reset to “AUTO.”
To change the input mode back to analog input, select
“ANALOG” by pressing INPUT ANALOG/DIGITAL again.
The following can be stored for each source:
• Bass boost (see page 12)
• Tone adjustment (see page 12)
• Input attenuator mode (see page 12)
• Subwoofer output level (see page 12)
• Balance (see page 13)
• DSP modes
– Surround mode (see page 26)
– DAP mode (see page 28)
• DVD MULTI playback mode (see page 30)
The above settings are stored automatically in the following cases:
• When you turn on the power.
• When you change the source.
• When you assign the source name.
Notes:
From the remote control:
1. Press the source selecting
button (DVD, CD, TV/DBS,
or TAPE/CDR)* for which
you want to change the
input mode.
DVD
DVD MUILTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
• You cannot assign and store different settings for digital input mode
and analog input mode.
• The DSP modes and DVD MULTI playback mode cannot be used at
the same time.
• If the source is FM or AM (MW/LW), you can assign a different
setting for each band.
Using the Sleep Timer
Note:
* Among the sources listed above, you can select the digital input
only for the sources which you have selected the digital input
terminals for. (See “Digital Input (DIGITAL IN) Terminal Setting.”)
2. Press ANALOG/DIGITAL to
change the input mode.
ANALOG/DIGITAL
INPUT
• Each time you press the button, the
input mode changes as follows:
ANALOG
AUTO
Using the Sleep Timer, you can fall asleep to music and know the
receiver will turn off by itself rather than play all night.
From the remote control ONLY:
Press SLEEP repeatedly.
SLEEP
The SLEEP indicator lights up on the display,
and the shut-off time changes as follows (in
minutes):
10
20
30
40
50
60
70
80
90
(Digital)
00 (Canceled)
When playing a software encoded with the DTS Digital
Surround, “AUTO” may not work properly. In this case, press
CONTROL UP 5/DOWN ∞ on the front panel to select “DTS.”
(See above.)
Note:
You can only select “ANALOG” and “AUTO” using the remote
control.
When the shut-off time comes
The receiver turns off automatically.
To check or change the time remaining until the shut-off time
Press SLEEP once.
The remaining time until the shut-off time appears in minutes.
• To change the shut-off time, press SLEEP repeatedly.
To cancel the Sleep Timer
Press SLEEP repeatedly until “SLEEP 00 MIN.” appears on the
display. (The SLEEP indicator goes off.)
• Turning off the power also cancels the Sleep Timer.
17
EN10_22.RX-7010&7012R[B]_f
17
01.1.9, 5:23 PM
Receiving Radio Broadcasts
You can browse through all the stations or use the preset function to go immediately to a particular station.
Tuning in Stations Manually
Using Preset Tuning
On the front panel:
1. Press FM/AM to select the band
(FM or AM — MW/LW).
FM/AM
The last received station of the selected band
is tuned in.
• Each time you press the button, the band alternates between
FM and AM (MW/LW).
Once a station is assigned to a channel number, the station can be
quickly tuned. You can preset up to 30 FM and 15 AM (MW/LW)
stations.
To store the preset stations
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
SPK 1
ANALOG
L
R
TUNED
2. Press FM/AM TUNING 5/ ∞until
you find the frequency you want.
VOLUME
On the front panel ONLY:
1. Tune in the station you want to preset (see
“Tuning in Stations Manually”).
FM/AM TUNING
• Pressing FM/AM TUNING 5 increases
the frequency.
• Pressing FM/AM TUNING ∞ decreases
the frequency.
• If you want to store the FM reception mode for this station,
select the FM reception mode you want. See “Selecting the
FM Reception Mode” on page 19.
SPK 1
ANALOG
L
R
VOLUME
TUNED
From the remote control:
1. Press FM/AM to select the band.
FM/AM
MEMORY
2. Press MEMORY.
• Each time you press the button, the band
alternates between FM and AM (MW/LW).
SPK 1
2. Press TUNING +/– until you find
the frequency you want.
• Pressing TUNING + increases the
frequency.
• Pressing TUNING – decreases the
frequency.
+
ANALOG
L
R
VOLUME
TUNED
CH-
TUNING
−
Notes:
• When a station of sufficient signal strength is tuned in, the TUNED
indicator lights up on the display.
• When an FM stereo program is received, the STEREO indicator
also lights up.
“CH-” appears and the channel number position starts flashing
on the display for about 5 seconds.
3. Press FM/AM PRESET 5/ ∞ to
select a channel number while the
channel number position is flashing.
FM/AM PRESET
SPK 1
ANALOG
L
R
TUNED
VOLUME
CH-
Note:
You can use the 10 keys on the remote control to select the preset
number. When using the 10 keys, be sure that they are activated
for the tuner, not for the CD and others. (See page 32.)
4. Press MEMORY again while the
selected channel number is flashing on
the display.
MEMORY
The selected channel number stops flashing.
The station is assigned to the selected channel number.
SPK 1
ANALOG
L
R
TUNED
VOLUME
CH-
5. Repeat steps 1 to 4 until you store all the
stations you want.
To erase a stored preset station
Storing a new station on a used number erases the previously stored
one.
18
EN10_22.RX-7010&7012R[B]_f
18
01.1.9, 5:23 PM
Selecting the FM Reception Mode
To tune in a preset station
On the front panel:
1. Press FM/AM to select the band
(FM or AM — MW/LW).
When an FM stereo broadcast is hard to
receive or noisy
FM/AM
You can change the FM reception mode while receiving an FM
broadcast.
• You can store the FM reception mode for each preset station.
The last received station of the selected band
is tuned in.
2. Press FM/AM PRESET 5/ ∞ until
you find the channel you want.
Press FM MODE on the front panel or on the
remote control.
FM/AM PRESET
• Each time you press the button, the FM reception mode
alternates between “AUTO” and “MONO.”
• Pressing FM/AM PRESET 5 increases the
channel numbers.
• Pressing FM/AM PRESET ∞ decreases the
channel numbers.
FM MODE
– SUB WOOFER +
0
FM MODE
From the remote control:
On the front panel
1. Press FM/AM.
FM/AM
• Each time you press the button, the band
alternates between FM and AM (MW/LW).
2. Press the 10 keys to select a preset
channel number.
•
•
•
•
On the remote control
For channel number 5, press 5.
For channel number 15, press +10 then 5.
For channel number 20, press +10 then 10.
For channel number 30, press +10, +10,
then 10.
SPK 1
ANALOG
EFFECT
1
L
R
AUTO MUTING TUNED STEREO
– CENTER +
2
3
MENU
TEST
4
– REAR • L +
5
6
ENTER
– REAR • R +
7/P
8
9
SPK 1
– SUB WOOFER +
10
0
+10
RETURN
FM MODE
100+
Note:
When you use the 10 keys on the remote control, be sure that they
are activated for the tuner, not for the CD and others. (See page 32.)
ANALOG
L
R
TUNED
AUTO: When a program is broadcasted in stereo, you will hear
stereo sound; when in monaural, you will hear
monaural sounds. This mode is also useful to suppress
static noise between stations. The AUTO MUTING
indicator lights up on the display.
MONO: Reception will be improved although you will lose the
stereo effect. In this mode, you will hear noise while
tuning into the stations. The AUTO MUTING indicator
goes off from the display.
Note:
When using the FM MODE button on the remote control, be sure that
the 10 keys are activated for the tuner, not for the CD and others.
(See page 32.)
19
EN10_22.RX-7010&7012R[B]_f
19
01.1.9, 5:23 PM
Using the RDS (Radio Data System) to
Receive FM Stations
RDS allows FM stations to send an additional signal along with their
regular program signals. For example, the stations send their station
names, as well as information about what type of program they
broadcast, such as sports or music, etc.
When tuned to an FM station which provides the RDS service, the
RDS indicator lights up on the display.
With the receiver, you can receive the following types of RDS
signals.
PS (Program Service): Shows commonly known station names
PTY (Program Type): Shows types of broadcast programs
RT (Radio Text):
Shows text messages the station sends
EON (Enhanced Other Network): See page 21.
Notes:
• RDS is not available for AM (MW/LW) broadcasts.
• RDS may not operate correctly if the station tuned is not
transmitting RDS signal properly or if the signal strength is weak.
What information can RDS signals provide?
You can see the RDS signals the station sends on the display.
To show the RDS signals
Press DISPLAY MODE on the front panel or DISPLAY on the
remote control while listening to an FM station.
Notes:
• When pressing DISPLAY on the remote control, make sure that you
have selected FM station using the remote control. If not, the
DISPLAY button does not work for tuner operation. (Pressing FM/
AM activates the remote control for tuner operation.)
• If searching finishes at once, “PS,” “PTY,” and “RT” will not appear
on the display.
Searching for a Program by PTY Codes
One of the advantages of the RDS service is that you can locate a
particular kind of program from the preset channels (see page 18) by
specifying the PTY codes.
To search for a program using the PTY codes
Before you start, remember...
• The PTY Search is only applicable to preset stations.
• To stop searching any time during the process, press PTY
SEARCH while searching.
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• When pressing the buttons on the remote control, make sure that
you have selected the FM station using the remote control. If not,
the RDS operation buttons do not work for RDS operation.
(Pressing FM/AM activates the remote control for RDS
operation.)
/REW PAUSE
FF/
FM/AM
DISPLAY MODE
PTY– PTY SEARCH PTY+
STOP
DISPLAY
STOP
DISPLAY
On the front panel
On the remote control
• Each time you press the button, the display changes to show you
the following information:
PS
Frequency
PTY
RT
PS (Program Service):
While searching, “PS” appears and then the station names will be
displayed. “NO PS” appears if no signal is sent.
PTY (Program Type):
While searching, “PTY” appears and then the type of the broadcast
program will be displayed. “NO PTY” appears if no signal is sent.
RT (Radio Text):
While searching, “RT” appears and then text messages the station
sends will be displayed. “NO RT” appears if no signal is sent.
Frequency:
Station frequency (non-RDS service)
About characters shown on the display
When the display shows PS, PTY, or RT signals, the following
characters are used.
• The display cannot differentiate upper case and lower case letters
and always uses upper case letters.
• The display cannot show accented letters, “A,” for instance, may
stand for accented “A’s” like “Å, Ä, Ã, Á, À, and Â.”
On the front panel:
1. Press PTY SEARCH while
listening to an FM station.
PTY SEARCH
“PTY SELECT” flashes on the display.
2. Press CONTROL UP 5/DOWN ∞
until the PTY code you want
appears on the display, while
“PTY SELECT” is flashing.
CONTROL
DOWN
UP
The display gives you the PTY codes described
on page 21.
3. Press PTY SEARCH again, while
the PTY code selected in the
previous step is still on the display.
PTY SEARCH
While searching, “SEARCH” and the
selected PTY code alternate on the display.
The receiver searches 30 preset FM stations, stops when it finds
the one you have selected, and tunes in that station.
To continue searching after the first stop
Press PTY SEARCH again while the indications on the display are
flashing.
If no program is found, “NOTFOUND” appears on the display.
20
EN10_22.RX-7010&7012R[B]_f
20
01.1.9, 5:23 PM
From the remote control:
1. Press PTY SEARCH while
listening to an FM station.
PAUSE
PTY SEARCH
“PTY SELECT” flashes on the display.
2. Press and hold PTY + or PTY –
until the PTY code you want
appears on the display, while
“PTY SELECT” is flashing.
FF/
PTY+
/REW
The display gives you the PTY codes
described below.
PTY–
3. Press PTY SEARCH again, while
the PTY code selected in the
previous step is still on the display.
PAUSE
Switching to a Broadcast Program of
Your Choice Temporarily
Another convenient RDS service is called “EON (Enhanced Other
Network).”
The EON indicator lights up while receiving an FM station with the
EON code. (The EON indicator also lights up while receiving an
AM station but the EON function will not work.)
This allows the receiver to switch temporarily to a broadcast
program of your choice (NEWS, TA, and/or INFO) from a different
station except in the following cases:
• When you are listening to non-RDS stations (all AM — MW/LW
and some FM stations).
• When the last received FM station is a non-RDS station.
• When the receiver is in standby mode.
PTY SEARCH
While searching, “SEARCH” and the
selected PTY code alternate on the display.
The receiver searches 30 preset FM stations, stops when it finds
the one you have selected, and tunes in that station.
To continue searching after the first stop
Press PTY SEARCH again while the indications on the display are
flashing.
If no program is found, “NOTFOUND” appears on the display.
Before you start, remember...
• The EON function is only applicable to preset stations.
On the front panel ONLY:
1. Press EON so that the last selected
program type appears on the
display.
EON
The receiver enters EON standby mode. When the
receiver is in EON standby mode, the receiver is
ready to receive the EON data (TA/NEWS/INFO)
you select.
PTY codes
NONE
ALARM
NEWS
TEST
AFFAIRS
DOCUMENT
INFO (INFORMATION)
FOLK M (MUSIC)
2. Press TA/NEWS/INFO until the
program type you want appears on
the display.
• Each time you press the button, the display changes
to show the following:
SPORT
TA
EDUCATE (EDUCATION)
OLDIES
NEWS
TA/NEWS/INFO
NATION M (NATIONAL MUSIC)
JAZZ
CULTURE
TA:
SCIENCE
NEWS: News.
INFO:
LEISURE
VARIED
TRAVEL
POP M (MUSIC)
PHONE IN
ROCK M (MUSIC)
RELIGION
EASY M (MUSIC)
SOCIAL (AFFAIRS)
LIGHT M (MUSIC)
CHILDREN
CLASSICS
FINANCE
OTHER M (MUSIC)
TA/NEWS
NEWS/INFO
TA/INFO
Traffic Announcement in your area.
Program the purpose of which is to impart advice in
the widest sense.
WEATHER
21
21
INFO
DRAMA
COUNTRY
EN10_22.RX-7010&7012R[B]_f
TA/NEWS/INFO
01.1.9, 8:11 PM
CASE 1
If there is no station broadcasting the program
you have selected
The receiver continues playing the current source (all sources
except AM — MW/LW).
‘
When a station starts broadcasting the program you have
selected, the receiver automatically switches to the station. The
indicator of received PTY code starts flashing.
‘
When the program is over, the receiver goes back to the
previously selected source, but still remains in EON standby
mode. The indicator of received PTY code stops flashing and
remains lit.
When an emergency broadcast (ALARM signal) is sent from an
FM station:
The receiver automatically tunes in the station except in the
following cases:
• When you are listening to non-RDS stations (all AM — MW/LW
and some FM stations).
• When the receiver is in standby mode.
While receiving an emergency broadcast, “ALARM” appears on the
display.
The TEST signal is used for equipment test — whether it can
receive the ALARM signal correctly.
The TEST signal makes the receiver work in the same way as the
ALARM signal does. If the TEST signal is received, the receiver
automatically switches to the station broadcasting the TEST signal.
While receiving the test signal, “TEST” appears on the display.
Notes:
CASE 2
If there is a station broadcasting the program
you have selected
The receiver changes the source (all sources except AM —
MW/LW), and tunes in the station. The indicator of received
PTY code starts flashing.
‘
When the program is over, the receiver goes back to the
previously selected source, but still remains in EON standby
mode. The indicator of received PTY code stops flashing and
remains lit.
CASE 3
If the FM station you are listening to is
broadcasting the program you have selected
• EON data sent from some stations may not be compatible with this
receiver.
• In EON standby mode, if you carry out synchronized recording (see
page 31), EON standby mode is canceled temporarily. The receiver
goes back to EON standby mode again when you have finished
that operation.
• The EON mode only works when receiving an FM station with the
EON code. (The EON indicator lights up while receiving an AM
station but the EON function will not work.)
• While listening to a program tuned in by the EON function, you
cannot use source selecting buttons and PTY SEARCH button.
CAUTION:
When the source alternates intermittently between the station tuned in
by the EON function and the currently selected source, press EON to
cancel the EON function.
If you do not press the button, the currently tuned station is received
finally, and the indication of the EON program type flashing on the
display disappears.
The receiver continues to receive the station, but the indicator
of received PTY code starts flashing.
‘
When the program is over, the indicator of received PTY code
stops flashing and remains lit, but the receiver remains in EON
standby mode.
To stop listening to the program selected by EON
Press EON so that the program type (TA/NEWS/INFO) indicator
goes off from the display. The receiver enters EON off mode and
goes back to the previously selected source.
• Each time you press EON, the EON mode alternates between
standby mode and off mode.
22
EN10_22.RX-7010&7012R[B]_f
22
01.1.9, 5:23 PM
Using the DSP Modes
The built-in Surround Processor provides two types of the DSP (Digital Signal Processor) mode — Surround mode and
DAP (Digital Acoustic Processor) mode.
What are the DSP Modes?
Surround modes
With this receiver, you can use three types of the Surround mode.
Following modes cannot be used when only the front speakers
are connected to this receiver (without the rear speakers or
center speaker).
JVC Theater Surround
In order to reproduce a more realistic sound field in your listening
room while playing soundtracks of software encoded with Dolby
Surround (bearing the mark
DOLBY SURROUND ), you can use JVC
Theater Surround.
Dolby Surround (Dolby Digital and Dolby Pro Logic)*
Used to watch the soundtracks of software encoded with Dolby
Digital (bearing the mark D I G I T A L ) or with Dolby Surround
DOLBY SURROUND ).
(bearing the mark
Dolby Surround encoding format records the left front channel, right
front channel, center channel, and rear channel (total 4 channels)
signals into 2 channels. The Dolby Pro Logic decoder built in this
receiver decodes these 2 channel signals into original 4 channel
signals — matrix-based multichannel reproduction, and allows you
to enjoy the realistic stereo sounds in your listening room.
On the other hand, Dolby Digital encoding method (so called
discrete 5.1 channel digital audio format) records and compresses
the left front channel, right front channel, center channel, left rear
channel, right rear channel, and LFE channel (total 6 channels, but
LFE channel is counted as 0.1 channel, therefore called 5.1
channels) signals digitally. Each channel is completely independent
from other channel signals to avoid interference, therefore, you can
obtain much better sound quality with much stereo and surround
effects.
The Dolby Digital decoder built in this receiver can create much
more realistic sound field in your listening room. You may feel as if
you were in a real theater.
In addition, Dolby Digital enables stereo rear sounds, and sets the
cutoff frequency of the rear treble at 20 kHz, compared to 7 kHz for
Dolby Pro Logic. These facts enhance the sound movement and
being-there feelings much more than Dolby Pro Logic.
• To enjoy the software encoded with Dolby Digital, you must
connect the source component using the digital terminal on the
rear of this receiver. (See page 8.)
Notes:
• The DSP modes have no effect on monaural sources.
• When you select “DVD MULTI” as the source to play, you cannot
select or adjust the DSP modes.
• The PRO LOGIC indicator lights up when the Dolby Pro Logic
decoder built in this receiver is activated.
DTS Digital Surround**
DTS Digital Surround is another discrete 5.1 channel digital audio
format available on CD, LD, and DVD software.
Compared to Dolby Digital, audio compression rate is relatively low.
This fact allows DTS Digital Surround format to add breadth and
depth to the reproduced sounds. As a result, DTS Digital Surround
features natural, solid and clear sound.
• To enjoy the software encoded with DTS Digital Surround, you
must connect the source component using the digital terminal on
the rear of this receiver. (See page 8.)
* Manufactured under license from Dolby Laboratories. “Dolby,” “Pro
Logic,” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential Unpublished Works. ©1992–1997 Dolby
Laboratories, Inc. All rights reserved.
** Manufactured under license from Digital Theater Systems, Inc. US
Pat. No. 5,451,942 and other world-wide patents issues and
pending. “DTS” and “DTS Digital Surround” are trademarks of
Digital Theater Systems, Inc. ©1996 Digital Theater Systems, Inc.
All rights reserved.
23
EN23_30.RX-7010&7012R[B]_f
23
01.1.9, 5:24 PM
Reproducing the Sound Field
DAP modes
In order to reproduce a more acoustic sound field in your listening
room while playing soundtracks of stereo sources, you can use DAP
modes. This mode can be used when the front speakers and the
rear speakers are connected to this receiver (without respect to
the center speaker connection).
You can select one of the following to your preference.
LIVE CLUB:
The sound heard in a concert hall or club consists of direct sound
and indirect sound — early reflections and reflections from behind.
Direct sounds reach the listener directly without any reflection. On
the other hand, indirect sounds are delayed by the distances of the
ceiling and walls. These direct sounds and indirect sounds are the
most important elements of the acoustic surround effects.
JVC Theater Surround and DAP modes can create these important
elements, and give you a real “being there” feeling.
Gives the feeling of a live music club with a low
ceiling.
DANCE CLUB: Gives a throbbing bass beat.
HALL:
Gives clear vocal and the feeling of a concert hall.
PAVILION:
Gives the spacious feeling of a pavilion with a high
ceiling.
Reflections from
behind
Early reflections
DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for
reproducing the analog discrete 5.1 channel output mode of the
DVD player or other equipment.
You can adjust the DVD MULTI playback mode while playing
back a video software such as a DVD using the analog discrete
5.1 channel output mode.
• For the DVD MULTI playback mode connection, see page 7.
• For details on the DVD MULTI playback mode, see page 30.
Direct sounds
INPUT
Available DSP modes according to the input mode
V: Possible
2: Impossible
BUTTON
SURROUND ON/OFF
DSP MODE
MODE
SURROUND ON
THEATER
LIVE CLUB
DANCE CLUB
HALL
PAVILION
DSP OFF
(SURROUND OFF)
ANALOG
(2 CH)
V
(DOLBY PRO LOGIC)
V
V
V
V
V
V
DVD MULTI
(ANALOG 5.1 CH)
2
2
2
2
2
2
2
LINEAR PCM
V
(DOLBY PRO LOGIC)
V
V
V
V
V
V
DOLBY DIGITAL
V *1
(DOLBY DIGITAL)
2
2
2
2
2
V
DTS
V *2
(DTS SURROUND)
2
2
2
2
2
V
*1 When 2 channel signal comes in, DOLBY PRO LOGIC is selected. When other signals come in, DOLBY DIGITAL is selected.
*2 When 2 channel signal comes in, DOLBY PRO LOGIC is selected. When other signals come in, DTS SURROUND is selected.
24
EN23_30.RX-7010&7012R[B]_f
24
01.1.9, 5:36 PM
Available DSP Modes According to the Speaker Arrangement
Available DSP modes will vary depending on how many speakers are used with this receiver.
Make sure that you have set the speaker information correctly (see page 14).
Speaker arrangements
Front
speaker
TV
Center speaker
Rear
speaker
Front
speaker
Front
speaker
Rear
speaker
TV
By pressing SURROUND ON/
OFF, the surround mode turns on
and off:
• SURROUND ON (PRO LOGIC,
DOLBY DIGITAL or DTS
SURROUND)
• SURROUND OFF (DSP mode is
canceled)
By pressing DSP MODE, the
DSP modes change as follows:
• THEATER
• LIVE CLUB
• DANCE CLUB
• HALL
• PAVILION
• DSP OFF (DSP mode is canceled)
By pressing SURROUND ON/
OFF, the surround mode turns
on and off:
• SURROUND ON (PRO LOGIC,
DOLBY DIGITAL or DTS
SURROUND)
• SURROUND OFF (DSP mode is
canceled)
By pressing DSP MODE, the
DSP modes change as follows:
• THEATER
• DSP OFF (DSP mode is canceled)
Front
speaker
Rear
speaker
Rear
speaker
Front
speaker
Available DSP modes
TV
Center speaker
Front
speaker
25
EN23_30.RX-7010&7012R[B]_f
25
01.1.9, 5:24 PM
Adjusting the Surround Modes
5. Adjust the speaker output levels.
Once you have adjusted the Surround modes, the adjustment is
memorized for each Surround mode.
Dolby and DTS Surround adjustments
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 3 again.
• You cannot adjust the rear speaker output levels when you have set
“REAR SPK” to “NO.” See page 14.
• You cannot adjust the center speaker output level when you have
set “CENTER SPK” to “NO.” See page 14.
• To adjust the center speaker level, press CENTER +/– (from
+10 dB to –10 dB).
• To adjust the left rear speaker level, press REAR•L +/– (from
+10 dB to –10 dB).
• To adjust the right rear speaker level, press REAR•R +/– (from
+10 dB to –10 dB).
ENTER
– CENTER +
2
– REAR • L +
3
– REAR • R +
8
9
6. Press TEST again to stop the test tone.
TEST
5
MENU
6
ENTER
4
From the remote control:
On the front panel:
1. Select and play a sound source.
• To enjoy Dolby Pro Logic, play back a software encoded with
DOLBY SURROUND mark.
Dolby Surround and labeled with
• To enjoy Dolby Digital, play back a software encoded with
Dolby Digital and labeled with
mark.
• To enjoy DTS Digital Surround, play back a software encoded
mark.
with DTS Digital Surround and labeled with
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make adjustments while listening to
the sound of the source played back.
D I G I T A L
2. Press SURROUND ON/OFF to
activate an appropriate Surround
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.
SURROUND
ON/OFF
• To enjoy Dolby Pro Logic, play back a software encoded with
DOLBY SURROUND mark.
Dolby Surround and labeled with
• To enjoy Dolby Digital, play back a software encoded with
Dolby Digital and labeled with
mark.
• To enjoy DTS Digital Surround, play back a software encoded
mark.
with DTS Digital Surround and labeled with
D I G I T A L
When “PRO LOGIC” is selected, the PRO LOGIC indicator
lights up on the display.
• Each time you press the button, the Surround mode turns on
and off alternately.
3. Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
4. Press TEST to check the speaker
output balance.
1. Select and play a sound source.
TEST
4
“TEST TONE L” starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
2. Press SURROUND ON/OFF to
activate an appropriate Surround
mode — PRO LOGIC, DOLBY
DIGITAL or DTS SURROUND.
SURROUND ON/OFF
When “PRO LOGIC” is selected, the PRO LOGIC indicator
lights up on the display.
• Each time you press the button, the Surround mode turns on
and off alternately.
3. Adjust the speaker output levels.
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CENTER
SPK” is set to “NO” (see page 14).
• No test tone comes out of the rear speakers when “REAR SPK”
is set to “NO” (see page 14).
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the selected speaker output level
(from +10 dB to –10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
ADJUST SETTING
CONTROL
DOWN
UP
26
EN23_30.RX-7010&7012R[B]_f
26
01.1.10, 4:05 PM
JVC Theater Surround adjustments
TEST
5. Press TEST again to stop the test tone.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 2 again.
• You cannot adjust the rear speaker output levels when you have set
“REAR SPK” to “NO.” See page 14.
• You cannot adjust the center speaker output level when you have
set “CENTER SPK” to “NO.” See page 14.
From the remote control:
MODE
EFFECT
1
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 3
DSP EFFECT 4
On the front panel:
You can also use the buttons on the front panel to adjust the
Surround modes. However, no test tone is available when using the
buttons on the front panel. So, make adjustments while listening to
the sound of the source played back.
The PRO LOGIC and DSP indicators also light up on the
display.
2. Press SOUND.
6. Press EFFECT to select an effect
level you want.
As the number increases, JVC Theater Surround becomes
stronger (normally set it to “DSP EFFECT 3”).
DSP
1. Press DSP MODE repeatedly until
“THEATER” appears on the
display.
4
SOUND
The 10 keys are activated for sound adjustments.
3. Press TEST to check the speaker
output balance.
1. Press DSP MODE repeatedly until
“THEATER” appears on the
display.
TEST
4
“TEST TONE L” starts flashing on the
display, and a test tone comes out of the
speakers in the following order:
The PRO LOGIC and DSP indicators also
light up on the display.
TEST TONE L
TEST TONE C
TEST TONE R
(Left front speaker)
(Center speaker)
(Right front speaker)
TEST TONE LS
TEST TONE RS
(Left rear speaker)
(Right rear speaker)
Notes:
• You can adjust the speaker output levels without outputting the
test tone.
• No test tone comes out of the center speaker when “CENTER
SPK” is set to “NO” (see page 14).
• No test tone comes out of the rear speakers when “REAR SPK”
is set to “NO” (see page 14).
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER +/– (from
+10 dB to –10 dB).
• To adjust the left rear speaker level, press REAR•L +/– (from
+10 dB to –10 dB).
• To adjust the right rear speaker level, press REAR•R +/– (from
+10 dB to –10 dB).
ENTER
– CENTER +
2
– REAR • L +
3
5
MENU
6
ENTER
DSP MODE
– REAR • R +
8
9
2. Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the selected speaker output level
(from +10 dB to –10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
ADJUST SETTING
CONTROL
DOWN
UP
3. Adjust the effect level.
1) Press ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.
2) Press CONTROL UP 5/DOWN ∞ to
select the effect level.
• Each time you press the button, the
effect level changes as follows:
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 5
ADJUST SETTING
CONTROL
DOWN
UP
DSP EFFECT 3
DSP EFFECT 4
As the number increases, JVC Theater Surround becomes
stronger (normally set it to “DSP EFFECT 3”).
27
EN23_30.RX-7010&7012R[B]_f
27
01.1.9, 5:24 PM
From the remote control:
Adjusting the DAP Modes
Once you have adjusted the DAP modes, the adjustment is
memorized for each DAP mode.
Before you start, remember...
• Make sure that you have set the speaker information correctly
(see page 14).
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
• You cannot adjust the rear speaker output level when you have set
“REAR SPK” to “NO.” See page 14.
1. Press DSP MODE repeatedly until
the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.
DSP
MODE
The DSP indicator also lights up on the display.
2. Press SOUND.
SOUND
The 10 keys are activated for sound adjustments.
On the front panel:
1. Press DSP MODE repeatedly until
the DAP mode — LIVE CLUB,
DANCE CLUB, HALL, or
PAVILION — appears on the
display.
DSP MODE
3. Adjust the rear speaker output
levels.
– REAR • L +
5
• To adjust the left rear speaker level, press
REAR•L +/– (from +10 dB to –10 dB).
• To adjust the right rear speaker level, press
REAR•R +/– (from +10 dB to –10 dB).
The DSP indicator also lights up on the display.
6
ENTER
ENTER
– REAR • R +
8
9
2. Adjust the rear speaker output levels.
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the selected speaker output level
(from +10 dB to –10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output level.
ADJUST SETTING
4. Press EFFECT to select an effect
level you want.
EFFECT
1
• Each time you press the button, the effect
level changes as follows:
DSP EFFECT 1
CONTROL
DOWN
UP
DSP EFFECT 2
DSP EFFECT 5
DSP EFFECT 3
DSP EFFECT 4
As the number increases, the selected DAP mode becomes
stronger (normally set it to “DSP EFFECT 3”).
3. Adjust the effect level.
1) Press ADJUST repeatedly until “DSP
EFFECT” appears on the display.
The display changes to show the current
setting.
2) Press CONTROL UP 5/DOWN ∞ to
select the effect level.
• Each time you press the button, the
effect level changes as follows:
DSP EFFECT 1
DSP EFFECT 2
DSP EFFECT 5
ADJUST SETTING
CONTROL
DOWN
UP
DSP EFFECT 3
DSP EFFECT 4
As the number increases, the selected DAP mode becomes
stronger (normally set it to “DSP EFFECT 3”).
28
EN23_30.RX-7010&7012R[B]_f
28
01.1.9, 5:24 PM
Activating the DSP Modes
For the other DSP modes
You can use only one DSP mode at a time. When a DSP mode is
activated, another DSP mode is canceled if in use.
For Dolby Pro Logic, Dolby Digital, and DTS
Digital Surround
1. Press DSP MODE repeatedly until the mode
you want appears on the display.
• Each time you press the button, the DSP modes change. (See
page 25 for more details.)
DSP MODE
1. Press SURROUND ON/OFF.
DSP
MODE
• Each time you press the button, the Dolby/DTS Surround turns
on and off alternately.
On the front panel
On the remote control
SURROUND ON/OFF
SURROUND
ON/OFF
2. Select and play a sound source.
• To enjoy JVC Theater Surround, play back a software encoded
DOLBY SURROUND mark.
with Dolby Surround and labeled with
On the front panel
On the remote control
2. Select and play a sound source.
To cancel the DSP mode
• To enjoy Dolby Pro Logic, play back a software encoded with
DOLBY SURROUND mark.
Dolby Surround and labeled with
• To enjoy Dolby Digital, play back a software encoded with
mark.
Dolby Digital and labeled with
• To enjoy DTS Digital Surround, play back a software encoded
mark.
with DTS Digital Surround and labeled with
D I G I T A L
To cancel the Dolby/DTS Surround mode
Press DSP MODE repeatedly until “DSP OFF” appears on the
display.
DSP MODE
On the front panel
Press SURROUND ON/OFF again. (“SURROUND OFF” appears
on the display.)
SURROUND ON/OFF
SURROUND
ON/OFF
On the front panel
On the remote control
29
EN23_30.RX-7010&7012R[B]_f
29
DSP
MODE
01.1.9, 5:24 PM
On the remote control
Using the DVD MULTI Playback Mode
This receiver provides the DVD MULTI playback mode for reproducing the analog discrete output mode of the DVD
player. Before playing back a DVD, refer also to the manual supplied with the DVD player.
Activating the DVD MULTI Playback Mode
You can adjust the DVD MULTI playback mode while playing back
a DVD using the analog discrete output mode on the DVD player.
Once you have made adjustments, the receiver memorizes the
adjustments until you change them. You also need to set the DVD
player to the analog discrete output mode.
Before you start, remember...
• There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step 1 again.
From the remote control:
1. Press DVD MULTI so that “DVD
MULTI” appears on the display.
DVD MUILTI
Note:
When you select “DVD MULTI” as the source to play, the DSP
mode is canceled, and the SURROUND ON/OFF and DSP
MODE buttons do not work.
2. Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
On the front panel:
1. Press DVD MULTI so that “DVD
MULTI” appears on the display.
DVD MULTI
If you need to make any adjustment, go to the following
steps.
SOUND
3. Press SOUND.
Note:
When you select “DVD MULTI” as the source to play, the DSP
mode is canceled, and the SURROUND ON/OFF and DSP
MODE buttons do not work.
2. Select the analog discrete output mode on the
DVD player, and start playing a DVD.
• Refer to the manual supplied with the DVD player.
If you need to make any adjustment, go to the following
steps.
The 10 keys are activated for adjusting the sound.
4. Adjust the speaker output levels.
• To adjust the center speaker level, press CENTER +/– (from
+10 dB to –10 dB).
• To adjust the left rear speaker level, press REAR•L +/– (from
+10 dB to –10 dB).
• To adjust the right rear speaker level, press REAR•R +/– (from
+10 dB to –10 dB).
ENTER
2
5
3
6
– REAR • R +
8
9
ENTER
MENU
3. Adjust the speaker output levels.
1) Press ADJUST repeatedly until one of
the following indications appears on
the display.
“CENTER LEVEL”:
To adjust the center speaker level.
“REAR L LEVEL”:
To adjust the left rear speaker level.
“REAR R LEVEL”:
To adjust the right rear speaker level.
2) Press CONTROL UP 5/DOWN ∞ to
adjust the selected speaker output level
(from +10 dB to –10 dB).
3) Repeat 1) and 2) to adjust the other
speaker output levels.
– REAR • L +
– CENTER +
ADJUST SETTING
CONTROL
DOWN
UP
30
EN23_30.RX-7010&7012R[B]_f
30
01.1.9, 5:24 PM
COMPU LINK Remote Control System
The COMPU LINK remote control system allows you to operate JVC audio components through the remote sensor on
the receiver.
To use this remote control system, you need to connect JVC audio
components through the COMPU LINK (SYNCHRO) jacks (see
below) in addition to the connections using cables with RCA pin
plugs (see pages 5 and 6).
• Make sure that the AC power cords of these components are
unplugged before connection. Plug the AC power cords only after
all connections are complete.
CD player
Cassette deck
or
CD recorder
COMPU LINK-4
(SYNCHRO)
Automatic Power On/Off (Standby): only possible
with the COMPU LINK-3 and COMPU LINK--4
connection
The connected components turn on and off (standby) along with the
receiver.
When you turn on the receiver, one of the connected component will
turn on automatically, depending on which component has been
previously selected.
When you turn off the receiver, the connected components will turn
off (standby).
Synchronized Recording
Synchronized recording means the cassette deck starts recording as
soon as a CD or a record begins playing.
To use synchronized recording, follow these steps:
1. Put a tape in the cassette deck, and a disc in the
CD player (or a record on the turntable).
2. Press the record (¶) button and the pause (8)
button on the cassette deck at the same time.
Turntable
This puts the cassette deck into recording pause.
If you do not press the record (¶) button and pause (8) button at
the same time, the synchronized recording feature will not
operate.
3. Press the play (3) button on the CD player or on
the turntable.
Notes:
• There are four versions of COMPU LINK remote control system.
This receiver is equipped with the fourth version — COMPU LINK4. This version is added systematic operations with the CD recorder
to the previous version — COMPU LINK-3.
• If your audio component has two COMPU LINK jacks, you can use
either one. If it has only one COMPU LINK jack, connect it so that it
is the last item in the series of components. (For example, the
turntable or CD player in the diagram above.)
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 13.)
• Refer also to the manuals supplied with your audio components.
The source changes on the receiver, and as soon as play starts,
the cassette deck starts recording. When the play ends, the
cassette deck enters recording pause, and stops about 4 seconds
later.
Notes:
• During synchronized recording, the selected source cannot be
changed.
• If the power of any component is shut off during synchronized
recording, the COMPU LINK remote control system may not
operate properly. In this case, you must start again from the
beginning.
This remote control system allows you to use four functions listed
below.
Remote Control through the Remote Sensor on the
Receiver
You can control the connected audio components through the remote
sensor on the receiver using this remote control. Aim the remote
control directly at the remote sensor on the receiver. For details, see
pages 32 and 33.
Automatic Source Selection
When you press the play (3
3) button on a connected component or
on its own remote control, the receiver automatically turns on and
changes the source to the component. On the other hand, if you
select a new source on the receiver or on the remote control, the
selected component begins playing immediately.
In both cases, the previously selected source continues playing
without sound for a few seconds.
31
EN31_40.RX-7010&7012R[B]_f
31
01.1.9, 5:24 PM
Operating JVC’s Audio/Video Components
You can operate JVC’s audio and video components with this receiver’s remote control, since control signals for JVC
components are preset in the remote control.
Operating Audio Components
Tuner
You can always perform the following operations:
FM/AM:
IMPORTANT:
To operate JVC’s audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 31) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel, the remote control will
not operate that source. To operate a source with the remote
control, the source must be selected using source selecting buttons
on the remote control.
• To operate the cassette deck or CD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 13.)
• Refer also to the manuals supplied with your components.
Alternates between FM and AM (MW/LW).
After pressing FM/AM, you can perform the following operations:
1 – 10, +10:
Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING +/–: Tunes into stations.
FM MODE:
Changes the FM reception mode.
PTY SEARCH: Searches for a program by PTY codes.
PTY +/–:
Selects the PTY codes.
DISPLAY:
Shows the RDS signals.
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND ON/OFF: Turns on or off the Surround modes –
Dolby Pro Logic, Dolby Digital, and
DTS Digital Surround.
DSP MODE:
Selects the DSP modes.
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MUILTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
+
−
BASS
+
SURROUND
DSP
ON/OFF
MODE
BASS BOOST EFFECT
1
TREBLE
After pressing SOUND, you can perform the following operations:
SUBWOOFER +/–:
CENTER +/–:
REAR•L +/–:
REAR•R +/–:
EFFECT:
TEST:
ANALOG/DIGITAL SLEEP
INPUT
– CENTER +
2
3
MENU
TEST
4
– REAR • L +
5
6
ENTER
SOUND
– REAR • R +
7/P
8
9
– SUB WOOFER +
MUTING
CATV/DBS
CONTROL
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
TV/VIDEO
−
Note:
−
After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys; otherwise,
the 10 keys cannot be used for operating your target source.
PLAY
+
/REW PAUSE
TUNING
−
FF/
PTY– PTY SEARCH PTY+
REC
PAUSE
STOP CONTROL
DISPLAY
CD player
After pressing CD, you can perform the following operations on the
CD player:
RM-SRX7010R
A/V CONTROL RECEIVER
* When you press one of the following buttons, the remote
control operation mode appears on the display window for
about 10 seconds.
Ex.: When you
press CD button
Buttons on the Remote Control
FM/AM
CD
PHONO
TAPE/CDR
DVD
DVD MULTI
TV/DBS
VCR
CATV/DBS CONTROL
CONTROL
SOUND
Adjusts the subwoofer output level.
Adjusts the center speaker output level.
Adjusts the left rear speaker output level.
Adjusts the right rear speaker output level.
Selects the effect level.
Turns on or off the test tone output.
Remote Control Operation Mode
TUNER
CD
PHONO
TAPE
DVD
DVD
TV
VCR
DBS
Current setting or VCR or TAPE
or CDDSC
SOUND
PLAY3:
4:
¢:
STOP7:
PAUSE8:
1 – 10, +10:
Starts playing.
Returns to the beginning of the current (or
previous) track.
Skips to the beginning of the next track.
Stops playing.
Pauses playing. To release it, press PLAY3.
Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
32
EN31_40.RX-7010&7012R[B]_f
32
01.1.9, 5:25 PM
CD changer
Cassette deck
After pressing CONTROL repeatedly until “CDDSC” appears on
the display window, you can perform the following operations on
the CD changer:
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can perform the following
operations on a cassette deck:
PLAY3:
4:
PLAY3:
REW:
FF:
STOP7:
PAUSE8:
REC PAUSE:
¢:
STOP7:
PAUSE8:
1 – 6, 7/P:
Starts playing.
Returns to the beginning of the current (or previous)
track.
Skips to the beginning of the next track.
Stops playing.
Pauses playing. To release it, press PLAY3.
Selects the number of a disc installed in a CD
changer.
Starts playing.
Fast winds the tape from right to left.
Fast winds the tape from left to right.
Stops operations.
Pauses playing. To release it, press PLAY3.
Starts recording or enters recording pause.
CD recorder
After pressing CD, you can perform the following operations on the
CD changer:
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
EXAMPLE:
• Selecting disc number 4, track number 12, and starting playback.
1. Press CONTROL repeatedly until “CDDSC” appears on the
display window, then press 4.
2. Press CD, then press +10, 2.
Turntable
After pressing PHONO, you can perform the following operations
on a turntable:
PLAY3:
STOP7:
After pressing TAPE/CDR (or CONTROL repeatedly until “TAPE”
appears on the display window), you can perform the following
operations on the CD recorder:
PLAY3:
4:
Starts playing.
Returns to the beginning of the current (or previous)
track.
¢:
Skips to the beginning of the next track.
STOP7:
Stops playing.
PAUSE8:
Pauses playing. To release it, press PLAY3.
REC PAUSE: Starts recording or enters recording pause.
Note:
You can use either TAPE/CDR button or CONTROL button to activate
the buttons listed above. If you press TAPE/CDR, the playing source
also changes. On the other hand, if you press CONTROL repeatedly
to select “TAPE,” the playing source does not change.
Starts playing.
Stops operations.
33
EN31_40.RX-7010&7012R[B]_f
33
01.1.9, 5:25 PM
Operating Video Components
VCR
You can always perform the following operations:
VCR
IMPORTANT:
To operate JVC’s video components using this remote control:
• Some JVC VCRs can accept two types of the control signals —
remote code “A” and “B.” Before using this remote control, make
sure that the remote control code of the VCR connected to the
VCR jacks is set to code “A.”
• When using the remote control:
– For the DVD player, TV, and VCR operations, aim the remote
control directly at the remote sensor on each component, not on
the receiver.
:
Turns on or off the VCR.
After pressing VCR (or CONTROL repeatedly until “VCR” appears
on the display window), you can perform the following operations
on the VCR:
1 – 9, 0:
PLAY3:
REW:
FF:
STOP7:
PAUSE8:
REC PAUSE:
CH +/–:
Selects the TV channels on VCR.
Starts playing.
Rewinds a tape.
Fast winds a tape.
Stops operations.
Pauses playing. To release it, press PLAY3.
Starts recording or enters recording pause.
Changes the TV channels on the VCR.
Note:
You can use either VCR button or CONTROL button to activate the
buttons listed above. If you press VCR, the playing source also
changes. On the other hand, if you press CONTROL repeatedly to
select “VCR,” the playing source does not change.
CATV/DBS
VCR
TV
AUDIO
DVD
DVD MUILTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
−
+
−
BASS
+
SURROUND
DSP
ON/OFF
MODE
BASS BOOST EFFECT
1
TREBLE
ANALOG/DIGITAL SLEEP
INPUT
4
3
– REAR • L +
5
6
ENTER
SOUND
– REAR • R +
7/P
After pressing DVD or DVD MULTI, you can perform the following
operations on a DVD player:
PLAY3:
4:
– CENTER +
2
MENU
TEST
DVD player
8
9
¢:
STOP7:
PAUSE8:
– SUB WOOFER +
MUTING
CATV/DBS
CONTROL
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
−
TV/VIDEO
−
−
Starts playing.
Returns to the beginning of the current (or previous)
track.
Skips to the beginning of the next track.
Stops playing.
Stops playing temporarily. To release it, press
PLAY3.
After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.
/REW PAUSE
−
FF/
PTY– PTY SEARCH PTY+
REC
PAUSE
– REAR • L +
5
6
ENTER
Note:
TUNING
3
MENU
TEST
4
PLAY
+
– CENTER +
2
– REAR • R +
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
8
9
STOP CONTROL
DISPLAY
RM-SRX7010R
A/V CONTROL RECEIVER
TV
You can always perform the following operations:
TV
:
Turns on or off the TV.
TV VOL +/–: Adjusts the volume.
TV/VIDEO: Sets the input mode (either TV or VIDEO).
After pressing TV/DBS, you can perform the following operations
on a TV:
CH +/–:
Changes the channels.
1 – 9, 0, 100+: Selects the channels.
RETURN:
Alternates between the previously selected channel
and the current channel.
34
EN31_40.RX-7010&7012R[B]_f
34
01.1.9, 5:25 PM
Operating Other Manufacturers’ Video Equipment
This remote control supplied with the receiver can transmit control
signals for other manufacturers’ VCRs, TVs, CATV converters,
DBS tuners, and DVD players. By changing the transmittable
signals from preset ones to the other manufacturers’, you can
operate the other manufacturer’s components using this remote
control.
When operating the other manufacturers’ components, refer also to
the manuals supplied with them. To operate these components with
the remote control, first you need to set the manufacturer’s code
each for VCR, TV, CATV converters, DBS tuner, and DVD player.
When replacing batteries of the remote control, set the
manufactures’ codes again.
To change the transmittable signals for
operating another manufacturer’s TV
1. Press and hold TV
.
2. Press TV/DBS.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list below to find the code.
4. Release TV
.
The following buttons can be used for operating the TV:
:
TV
TV VOL +/–:
TV/VIDEO:
Turns on and off the TV.
Adjusts the volume.
Sets the input mode (either TV
or VIDEO).
After pressing TV/DBS, you can perform the following
operations on a TV:
CATV/DBS
VCR
TV
DVD
DVD MUILTI
CD
FM/AM
TV/DBS
VCR
TAPE/CDR
PHONO
+
−
+
−
BASS
SURROUND
DSP
ON/OFF
MODE
BASS BOOST EFFECT
1
AUDIO
TREBLE
ANALOG/DIGITAL SLEEP
INPUT
– CENTER +
2
3
MENU
TEST
4
– REAR • L +
5
6
ENTER
SOUND
– REAR • R +
7/P
9
Note:
Refer to the manual supplied with your TV.
5. Try to operate your TV by pressing TV
10
0
+10
RETURN
FM MODE
100+
+
+
+
CH
TV VOL
VOLUME
CATV/DBS
CONTROL
−
TV/VIDEO
−
−
PLAY
+
/REW PAUSE
TUNING
−
FF/
PTY– PTY SEARCH PTY+
STOP CONTROL
DISPLAY
RM-SRX7010R
A/V CONTROL RECEIVER
Manufacturers’ codes are subject to change without notice.
If they are changed, this remote control cannot operate the
equipment.
Manufacturer
Codes
JVC
AKAI
BLAUPUNKT
FISHER
GRUNDIG
HITACHI
IRADDIO
ITT/NOKIA
LOEWE
MAGNAVOX
METS
MITSUBISHI
MIVAR
NORDMENDE
OKANO
PANASONIC
PHILIPS
QUELLE
00, 02, 13, 14, 47, 74
01, 02
03, 04
01, 05
03, 06, 07
08, 09, 10, 49
02
11, 12
06, 15, 16
08, 17, 49
50, 51, 52, 53
08, 18, 19, 20
21
22, 23
15
24, 25, 26, 27, 76
15, 17, 28, 75
52, 53, 54, 55, 56, 57, 58,
59, 60, 61, 62, 63, 64, 65,
66, 67
08, 24, 29, 30, 31, 48
32, 33, 68, 69, 70
06, 08, 16, 34, 35, 49
01, 05
02, 15, 36
37, 38, 77
39
40, 41, 42, 69
71, 72
37, 43, 44
45, 46
RCA/PROSCAN
SABA
SAMSUNG
SANYO
SCHNEIDER
SHARP
SONY
TELEFUNKEN
THOMSON
TOSHIBA
ZENITH
35
EN31_40.RX-7010&7012R[B]_f
.
When your TV turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
– SUB WOOFER +
MUTING
REC
PAUSE
8
CH +/–:
Changes the channels.
1 – 10, 0, 100+ (+10): Selects the channels.
The 10 button will function as the
ENTER button if your TV requires
pressing ENTER after selecting a
channel number.
35
01.1.9, 5:25 PM
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Press and hold CATV/DBS
.
2. Press CATV/DBS CONTROL.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list to the right to find the code.
4. Release CATV/DBS
.
The following buttons can be used for operating the CATV
converter or DBS tuner:
CATV/DBS
:
Turns on and off the CATV converter
or DBS tuner.
CH +/–:
Changes the channels.
1 – 10, 0, 100+ (+10): Selects the channels.
The 10 button will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer to the manual supplied with your CATV converter or DBS
tuner.
5. Try to operate your CATV converter or DBS
.
tuner by pressing CATV/DBS
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner , try each one until the correct
one is entered.
Note:
You cannot use both the CATV converter and DBS tuner at the same
time.
For CATV converter
Manufacturer
Codes
GENERAL INSTRUMENT 06, 07, 08, 09, 10,
11, 12, 13, 14, 29
HAMLIN/REGAL
01, 02, 03, 04, 05
JERROLD
06, 07, 08, 09, 10,
11, 12, 13, 14
OAK
15, 16, 17
PANASONIC
18, 19, 20
PIONEER
21, 22
SCIENTIFIC ATLANTA
23, 24, 25
TOCOM
26
ZENITH
27, 28
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
For DBS tuner
Manufacturer
Codes
JVC
AMSTRAD
BLAUPUNKT
ECHOSTAR
GOLDSTAR
GRUNDIG
HIRSHMANN
INSTRUMENT
ITT/NOKIA
KATHREIN
NEC
ORBITECH
PHILIPS
RCA
SAMSUNG
SCHWAIGER
SIEMENS
SONY
TECHNISAT
56, 57, 67
43, 44, 45, 46, 47, 48, 49
30
50, 51, 67
31
32, 33
48, 52, 53, 54, 55
68
34
52, 58, 59, 60, 61, 62, 63
35, 36
48
37, 38
65
39, 40
61, 64
41, 42
66
48
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
36
EN31_40.RX-7010&7012R[B]_f
36
01.1.9, 5:25 PM
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR
Manufacturer
.
2. Press VCR.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list to the right to find the code.
4. Release VCR
.
The following button can be used for operating the VCR:
VCR
:
Turns on and off the VCR.
After pressing VCR, you can perform the following operations
on the VCR:
CH +/–:
Changes the TV channels on the VCR.
1 – 10, 0, 100+ (+10): Selects the TV channels.
The 10 button will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a
channel number.
PLAY3:
Starts playback.
REW:
Rewinds a video tape.
FF:
Fast winds a video tape.
STOP7:
Stops operation.
PAUSE8:
Pauses.
REC PAUSE: Starts recording or enters recording pause.
Note:
Refer to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR
.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
JVC
AIWA
BELL & HOWELL
BLAUPUNKT
CGM
EMERSON
FISHER
FUNAI
GE
GOLDSTAR
GOODMANS
GRUNDIG
HITACHI
LOEWE
MAGNAVOX
MITSUBISHI
NEC
NOKIA
NORDMENDE
ORION
PANASONIC
PHILIPS
PHONOLA
RCA/PROSCAN
SABA
SAMSUNG
SANYO
SHARP
SIEMENS
SONY
TELEFUNKEN
TOSHIBA
ZENITH
37
00, 26, 27, 28, 29, 58
01, 02
03
04, 05
06, 07
08, 10, 11, 12, 64, 65
03, 14, 15, 16, 17
01
18, 19, 20
07
13, 21
06, 22
18, 23, 24, 25, 66
07, 21
04, 19, 24
30, 31, 32, 33, 34, 35
26, 27
03, 36
38
09
19, 24, 39, 40
04, 19, 21, 24, 41, 42
21
04, 18, 19, 23, 24, 43, 44,
45
38, 46
45, 47, 59, 61, 62, 63
03, 48, 49
37, 50
03, 51
52, 53, 54
55, 60
43, 44
56, 57
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
37
EN31_40.RX-7010&7012R[B]_f
Codes
01.1.9, 5:25 PM
To change the transmittable signals for
operating another manufacturer’s DVD player
1. Press and hold AUDIO
.
Manufacturer
2. Press DVD.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list to the right to find the code.
4. Release AUDIO
.
After pressing DVD or DVD MULTI, you can perform the
following operations on a DVD player:
PLAY3:
4:
¢:
STOP7:
PAUSE8:
Starts playing.
Returns to the beginning of the current (or
previous) tracks.
Skips to the beginning of the next track.
Stops playing.
Stops playing temporarily. To release it, press
PLAY3.
After pressing DVD or DVD
MULTI, these buttons can be used
for the DVD menu operations.
JVC
DENON
PANASONIC
PHILIPS
PIONEER
RCA
SAMSUNG
SONY
TOSHIBA
YAMAHA
Codes
00, 02
01
03
13
04, 05, 06
07
08
09
10
11, 12
Manufacturers’ codes are subject to change without
notice. If they are changed, this remote control cannot
operate the equipment.
– CENTER +
2
3
MENU
– REAR • L +
TEST
4
5
6
ENTER
Note:
– REAR • R +
For detailed menu operations, refer to the
instructions supplied with the discs or the
DVD player.
8
9
Note:
Refer to the manual supplied with your DVD player.
5. Try to operate your DVD player by pressing one
of the above buttons.
• DO NOT forget to turn on the DVD player before pressing one
of the above buttons.
If there are more than one code listed for your brand of DVD
player, try each one until the correct one is entered.
38
EN31_40.RX-7010&7012R[B]_f
38
01.1.9, 5:25 PM
Troubleshooting
Use this chart to help you solve daily operational problems. If there is any problem you cannot solve, contact your JVC
service center.
PROBLEM
SOLUTION
POSSIBLE CAUSE
The display does not light up.
The power cord is not plugged in.
Plug the power cord into an AC outlet.
No sound from speakers.
Speaker signal cables are not connected.
Check speaker wiring and reconnect if
necessary.
The SPEAKERS ON/OFF 1 and 2 buttons
are not set correctly.
Press SPEAKERS ON/OFF 1 and 2 correctly.
An incorrect source is selected.
Select the correct source.
Muting is activated.
Press MUTING to cancel the mute.
An incorrect input mode (analog or
digital) is selected.
Select the correct input mode (analog or
digital).
Connections are incorrect.
Check connections.
For analog connections, see page 5.
For digital connections, see page 8.
Speaker signal cables are not connected
properly.
Check speaker wiring and reconnect if
necessary.
The balance is set to one extreme.
Adjust the balance properly (see page 13).
Incoming signal is too weak.
Connect an outdoor FM antenna or contact
your dealer.
The station is too far away.
Select a new station.
An incorrect antenna is used.
Check with your dealer to be sure you have
the correct antenna.
Antennas are not connected properly.
Check connections.
Occasional cracking noise during FM
reception.
Ignition noise from automobiles.
Move the antenna farther from automobile
traffic.
Howling during record playing.
Your turntable is too close to speakers.
Move speakers away from the turntable.
Noise is heard.
An earth (H) cable is not connected to the
AM (H) terminal on the rear panel.
Connect the cable to the AM (H) terminal on
the rear panel.
“OVERLOAD” starts flashing on the
display.
Speakers are overloaded because of high
volume.
1. Press STANDBY/ON
on the front
panel to turn off the receiver.
2. Stop the playback source.
3. Turn on the receiver again, and adjust the
volume.
Speakers are overloaded because of short
circuit of speaker terminals.
Press STANDBY/ON
on the front panel,
then check the speaker wiring.
If “OVERLOAD” does not disappear, unplug
the AC power cord, then plug it back again.
If speaker wiring is not short-circuited, contact
your dealer.
“DSP MICON NG” starts flashing on the
display.
The built-in microcomputer is not
functioning correctly.
Press STANDBY/ON
on the front panel
to turn off the receiver. After unplugging the
power cord, consult your dealer.
The STANDBY lamp lights up after
turning on the power, but soon the
receiver turns off (into standby mode).
The receiver is overloaded because of a
high voltage.
Press STANDBY/ON
on the front panel
to turn off the receiver. After unplugging the
power cord, consult your dealer.
Remote control does not work.
There is an obstruction in front of the
remote sensor on the receiver.
Remove the obstruction.
Batteries are weak.
Replace batteries.
An incorrect remote control operation
mode is selected.
Select the correct remote control operation
mode. (See page 32).
Sound from one speaker only.
Continuous hiss or buzzing during FM
reception.
Remote control does not operate
intendedly.
Note:
When you use the digital coaxial connection, the sounds may be intermitted by the outside noise such as a lightning discharge but they will
restore automatically. This is not a malfunction.
39
EN31_40.RX-7010&7012R[B]_f
39
01.1.16, 1:24 PM
Specifications
Amplifier
Output Power
At Stereo operation:
Front channels:100 W per channel, min. RMS, both channels
driven into 8 Ω at 1 kHz with no more than 0.9%
total harmonic distortion. (IEC268-3/DIN)
At Surround operation:
Front channels: 100 W per channel, min. RMS, driven into 8 Ω
at 1 kHz with no more than 0.8% total harmonic
distortion.
Center channel: 100 W, min. RMS, driven into 8 Ω at 1 kHz,
with no more than 0.8% total harmonic
distortion.
Rear channels: 100 W per channel, min. RMS, driven into 8 Ω
at 1 kHz, with no more than 0.8% total
harmonic distortion.
Audio
Audio Input Sensitivity/Impedance (1 kHz):
PHONO (MM):
2.7 mV/47 kΩ
CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:
220 mV/47 kΩ
Audio Input (DIGITAL IN)* :
Coaxial: DIGITAL 1 (DVD): 0.5 V(p-p)/75 Ω
Optical: DIGITAL 2 (CD), DIGITAL 3 (TV), DIGITAL 4 (CDR):
–21 dBm to –15 dBm (660 nm ±30 nm)
* Corresponding to Linear PCM, Dolby
Digital, and DTS Digital Surround (with sampling
frequency — 32 kHz, 44.1 kHz, 48 kHz).
Video
Video Input Sensitivity/Impedance:
Composite video:
DBS, VCR, DVD: 1 V(p-p)/75 Ω
S-video: DBS, VCR, DVD: (Y: luminance): 1 V(p-p)/75 Ω
(C: chrominance, burst): 0.286 V(p-p)/75 Ω
Video Output Level:
Composite video: VCR, MONITOR OUT:
1 V(p-p)/75 Ω
S-video: VCR, MONITOR OUT:
(Y: luminance): 1 V(p-p)/75 Ω
(C: chrominance, burst): 0.286 V(p-p)/75 Ω
Synchronization:
Negative
Signal-to-Noise Ratio: 45 dB
FM tuner (IHF)
Tuning Range: 87.50 MHz to 108.00 MHz
Usable Sensitivity: Monaural: 17.0 dBf (1.95 µV/75 Ω)
50 dB Quieting Sensitivity:
Monaural:
Stereo:
21.3 dBf (3.2 µV/75 Ω)
41.3 dBf (31.5 µV/75 Ω)
Signal-to-Noise Ratio (IHF-A weighted):
Monaural:
78 dB at 85 dBf
Stereo:
73 dB at 85 dBf
Total Harmonic Distortion:
Monaural:
Stereo:
0.4% at 1 kHz
0.6% at 1 kHz
Audio Output Level:
TAPE/CDR, VCR: 220 mV
Stereo Separation at REC OUT: 35 dB at 1 kHz
Digital output:
Optical: DIGITAL OUTPUT
Signal wave length:
660 nm
Output level: –21 dBm to –15 dBm
Frequency Response:
Signal-to-Noise Ratio (’66 IHF/DIN):
PHONO (MM):
70 dB/66 dB (at REC OUT)
CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:
87 dB/67 dB
Tuning Range: MW:
LW:
Frequency Response (8 Ω):
PHONO: 20 Hz to 20 kHz (±1 dB)
CD, TAPE/CDR, TV SOUND/DBS, VCR, DVD:
20 Hz to 20 kHz (±1 dB)
Signal-to-Noise Ratio:
RIAA Phono Equalization:
Bass boost:
Alternate Channel Selectivity: 60 dB: (±400 kHz)
±10 dB (20 Hz to 20 kHz)
+3 dB ±1.0 dB at 100 Hz
Tone Control:
Bass (100 Hz): ±10 dB
Treble (10 kHz): ±10 dB
30 Hz to 15 kHz: (+0.5 dB, –3 dB)
AM (MW/LW) tuner
Usable Sensitivity:
522 kHz to 1 629 kHz
144 kHz to 288 kHz
Loop antenna: 400 µV/m (MW)
50 dB (100 mV/m)
General
Power Requirements: AC 230V
, 50 Hz
Power Consumption: 200 W (at operation)
2 W (in standby mode)
Dimensions (W x H x D): 435 mm x 146.5 mm x 425.5 mm
(17 3/16 in. x 5 13/16 in. x 16 13/16 in.)
Mass:
8.6 kg (19.0 lbs)
Designs & specifications are subject to change without notice.
40
EN31_40.RX-7010&7012R[B]_f
40
01.1.9, 5:25 PM
VICTOR COMPANY OF JAPAN, LIMITED
V
EN
RX-7010&7012R[B]COVER_f
J
2
01.1.9, 5:21 PM
C
0301NHMMDWJEIN
Download PDF