Milli Glance wall basin set Specification

Add to My manuals
3 Pages

advertisement

Milli Glance Wall Basin Set Specification | Manualzz

MILLI GLANCE

WALL BASIN SET

60

37

60

36 page 1 of 3

200

202

180

6

53

SPECIFICATIONS

Recommended Use

Finish Available

Pressure Rating

Temperature Rating

Suitable Hot Water

WELS

Standards

Domestic, hotel and commercial

Chrome

Matte Black

Rose Gold

Brushed Nickel

Gun Metal

Maximum continuous operating pressure 500 kPa.

Note: For best performance and longer life, we recommend 150-500 kPa.

Maximum continuous working temperature 75 o C

Storage Tank: Yes

Continuous Flow: Refer to manufacturer of continuous hot water systems

Gravity Feed: No

Stars: 5

Flow Rate: 5.5lt/min

AS/NZS 3718

CLEANING RECOMMENDATIONS

We recommend the use of soapy water or approved cleaners.

This product should not be cleaned with abrasive materials.

Damage caused by any improper treatment is not covered by the product warranty- refer to Warranty Conditions on the last page.

To see the complete MILLI GLANCE range go to www.reece.com.au/bathrooms

The more water efficient

WATER

RATING

A joint government and industry program

Licence No. 0133

5.5

litres per minute

When tested at 150, 250 & 350kPa in accordance with Standard AS/NZS 6400 www.waterrating.gov.au

AS/NZS 3718

WM-025986

Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions are nominal measurements only. Dimensions and set-outs listed are correct at time of publication however the manufacturer/distributor takes no responsibility for printing errors.

Tech Page Version 1

MILLI GLANCE

WALL BASIN SET

page 2 of 3

INSTALLATION INSTRUCTIONS

Important Note

Mixer must be installed to the requirements of AS/NZS 3500 by a qualified plumber. Your mixer comes to you already factory assembled and tested. We do not recommend the dismantling of any internal part of the mixer. The mixers are factory tested and sealed so as to give the best performance.

Firmly screw Spindle into the Breach.

DO NOT OVERTIGHTEN

Flange

Handle Washer

Handle

Grub Screw

Allen Key

Screw Plug

Bonnet

O-Ring

Dress Plate

Spindle

Fibre Washer

Fit Fibre Washer around the Spindle and then firmly fasten the Bonnet onto the

Spindle using a spanner.

BREACH SET-UP

- Ensure that seats in the Breach are

in good condition and are free of

foreign objects.

- The reccomended installation

range for the breach are as shown:

MAX: 15mm inwards from the

Front Wall Surface

MIN: 2mm inwards from the

Front Wall Surface

- Reseat if required.

MAX: 15mm

MIN: 2mm

Breach

Front Wall Surface

Fit O-Ring to the groove in the rear of the Dress Plate.

Fit Dress Plate over the

Spindle.

Firmly fasten Flange onto the Spindle to secure the

Dress Plate.

INSTALLATION INSTRUCTIONS

WALL TOP ASSEMBLIES

IN0275 REV A

Fit Handle Washer around the Flange.

Fit Handle to Spindle and fasten with the Grub Screw using the Allen Key provided.

Push Screw Plug into hole.

recommended working pressure

- If the pressure exceeds or is likely to exceed 550kpa,

an approved pressure limiting device must be installed.

- Flush out all pipe work prior to installation.

- If the water temperature exceeds 75°C, an approved

tempering valve must be fitted.

- Installation should comply with Australian standard

AS3500.1 or relevant local authority requirements.

Showers may not be suitable for use within:

• Gravity-fed water systems

• Some instantaneous hot water systems; or

- Apply Teflon Tape to Threaded Elbow.

- Fit O-Ring to the groove in the back of the Dress Plate.

- Screw the Wall Outlet onto the Threaded Elbow until firmly

fastened and with the spout pointed downwards.

• Pressure supply less than 150kPa;

NOTE: The 500kPa maximum water supply pressure does not apply to fire service outlets.

Failure to comply with the above may void all warranties.

WARRANTY:

Please refer to the full warranty statement enclosed with the product before installing.

- Products should be cleaned with mild

liquid detergent or soap and water.

- Do not use cream cleaners or citrus

based cleaning products, as they are

abrasive.

- Use of unsuitable cleaning agents may

damage the surface. Any damage caused

in this way will not be covered by

warranty.

While we aim to ensure the specifications shown are correct at

INSTALLATION INSTRUCTIONS

MILLI GLANCE WALL OUTLET

IN0281 REV A

*All measurements are shown in millimeters.

Teflon Tape

Threaded Elbow

O-Ring

Dress Plate

Wall Outlet recommended working pressure maximum hot water temperature

- If the pressure exceeds or is likely to exceed 550kpa,

an approved pressure limiting device must be installed.

- Flush out all pipe work prior to installation.

- If the water temperature exceeds 75°C, an approved

tempering valve must be fitted.

- Installation should comply with Australian standard

AS3500.1 or relevant local authority requirements.

Showers may not be suitable for use within:

• Gravity-fed water systems

• Some instantaneous hot water systems; or

• Pressure supply less than 150kPa;

NOTE: The 500kPa maximum water supply pressure does not apply to fire service outlets.

Failure to comply with the above may void all warranties.

Please refer to the full warranty statement enclosed with the product before installing.

- Products should be cleaned with mild

liquid detergent or soap and water.

- Do not use cream cleaners or citrus

based cleaning products, as they are

abrasive.

- Use of unsuitable cleaning agents may

damage the surface. Any damage caused

in this way will not be covered by

warranty.

While we aim to ensure the specifications shown are correct at the time of printing, we reserve the right to make modifications without prior notice. Always use the physical product measurements for mark-ups and roughing-in as the line drawing shown may differ from the actual product over time.

*All measurements are shown in millimeters.

Plumbers, please ensure a copy of the installation instructions is left with the end user for future reference

MILLI GLANCE

WALL BASIN SET

Q

U

ALIT

7

YEAR

Y GUARA

NT

EE page 3 of 3

REECE PRODUCT QUALITY GUARANTEE

You have purchased a quality product from Reece Pty Ltd

ABN 84 004 097 090 (“Reece”). This product is covered by a

7 year replacement product warranty and a 12 month warranty over spare parts and labour.

7 YEAR WARRANTY – DOMESTIC USE

This warranty covers faults in the product construction, material and assembly. Products which are within 7 years from the date of purchase, found upon inspection by an authorised

Reece representative, to be defective in construction, material or assembly, will be repaired or exchanged with an equivalent product free of charge. Replaced items become Reece’s property. This warranty also covers any spare parts included under “Manufacturer’s Provisions” below.

All replacement products will be available for collection without charge to the customer at the nearest Reece branch to the customer’s location, or elsewhere as agreed between the customer and Reece.

Manufacturer’s Provisions

The following spare parts are covered by a 15 year warranty: w Mixer Cartridge

Labour and Spare Parts

The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier within 1 year from the date of purchase.

Spare parts other than those listed in the Manufacturer’s

Provisions above, which are within 1 year from the date of purchase found upon inspection by an authorised Reece representative to be defective in construction, material or assembly, will be replaced free of charge.

Warranty Conditions

This warranty will apply only under all of the following conditions: w The item has been installed by a licensed plumber w The item has been installed for and subjected to domestic residential use only w Failure is due to a fault in the manufacture of the product w Proof of purchase (including the date of purchase) is provided w The installation of the product is in accordance with the instructions provided

This warranty does not cover products purchased as an ex-display without being fully checked and tested for sale by the manufacturer.

This warranty does not include faults caused by: w Unsuitable or improper use w Incorrect installation or installation not in accordance with the instructions provided w Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER w Normal wear and tear w Inadequate or complete lack of maintenance w Chemical, electrochemical or electrical influences w Harsh detergents or abrasive cleaners used on product finishes

1 YEAR WARRANTY – COMMERCIAL USE

‘Commercial’ use is all use other than for normal domestic residential purposes, including use in non-business places as in public buildings, schools, sports centres and in establishments that contain private bathrooms with high frequency of use by many individuals, such as hotels, motels, retirement villages and hospitals.

The Commercial warranty covers this product against manufacturing faults in the construction, material and assembly of both the finished products and any spare parts for a period of 1 year from the date of purchase. Products and spare parts which are found upon inspection by an authorised

Reece representative to be defective in construction, material or assembly will be repaired or exchanged free of charge.

Replaced items become Reece’s property. The labour for the replacement of products and spare parts to which this warranty applies will be supplied by Reece or relevant supplier using licensed plumbers engaged by Reece or relevant supplier. The

Warranty Conditions and exclusions which apply to the noncommercial warranty also apply to this commercial warranty.

EXCLUSIONS

To the fullest extent permitted by law, Reece excludes all liability for damage or injury to any person, damage to any property, and any indirect consequential or other loss or damage.

CLAIM PROCEDURE

For all warranty queries customers are to contact the branch where the product was purchased. These details can be found on your purchase invoice.

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

Don’t risk it, use a licensed plumber.

advertisement

Key Features

  • Chrome, Matte Black, Rose Gold, Brushed Nickel, Gun Metal finishes
  • 500 kPa pressure rating (150-500 kPa recommended)
  • 75°C maximum working temperature
  • 5 star WELS rating
  • 5.5lt/min flow rate
  • AS/NZS 3718 standards

Related manuals

Frequently Answers and Questions

What are the different finishes available for the Milli Glance wall basin set?
The Milli Glance wall basin set is available in Chrome, Matte Black, Rose Gold, Brushed Nickel, and Gun Metal finishes.
What is the maximum operating pressure for the Milli Glance wall basin set?
The maximum continuous operating pressure for the Milli Glance wall basin set is 500 kPa. For best performance and longer life, we recommend 150-500 kPa.
What is the maximum working temperature for the Milli Glance wall basin set?
The maximum continuous working temperature for the Milli Glance wall basin set is 75°C.
Download PDF

advertisement