User Manual

Add to my manuals
51 Pages

advertisement

User Manual | Manualzz
EZN Plus series Network Camera
User Manual
Copyright © EverFocus Electronics Corp,
Release: February 2012
EZN-Series IP Cameras
Product Name: EZN Plus series Megapixel HD Outdoor IR & WDR Bullet Network Camera
FCC Notice "Declaration of Conformity Information"
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Warning: Changes or modifications made to this equipment, not expressly approved by EverFocus or parties
authorized by EverFocus could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
EverFocus Electronics Corp.
12F, No. 79, Sec. 1, Shin-Tai Wu Rd., Hsi-Chi,
Taipei Hsien, Taiwan, R.O.C.
EZN Plus series cameras comply with CE and FCC regulations.
About this document
2
EZN-Series IP Cameras
All the safety and operating instructions should be read and followed before the unit is operated. This manual should
be retained for future reference. The information in this manual was current when published. The manufacturer
reserves the right to revise and improve its products. All specifications are therefore subject to change without
notice.
Safety Notice
These limits are designed to provide reasonable protection. This equipment generates, uses and can radiated radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the distance between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
To reduce risk of fire or electric shock, do not expose this appliance to rain or moisture.
Do not attempt to disassemble the appliance. To prevent electric shock, do not remove screws or covers.
There are no user-serviceable parts inside. Contact qualified service personnel for maintenance. Handle the
appliance with care. Do not strike or shake, as this may damage the appliance.
Do not use strong or abrasive detergents when cleaning the appliance body. Use a dry cloth to clean the
appliance when it is dirty. When the dirt is hard to remove, use a mild detergent and wipe gently.
3
EZN-Series IP Cameras
Do not operate the appliance beyond its specified temperature, humidity or power source ratings. Do not use
the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at a
temperature between -40°C and 55°C / -40°F and 131°F (DC 12V only) and -20°C ~ 55°C / -4°F ~ 131°F (for PoE ) .
Humidity level between 20% and 80% non-condensing. The input power source for this appliance is DC 12V & PoE.
Use only the recommended power supplies. Power supplies must comply with the requirement of the latest
version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard.
Electrostatic-sensitive device. Use proper CMOS/MOSFET handing precautions to avoid electrostatic
discharge.
Installation should be performed by qualified service personnel only in accordance with the National Electrical
Code or applicable local codes.
Terms and Trademark
Ethernet, Internet Explorer, Linux, Microsoft, Windows, WWW are registered trademarks of the respective holders.
Other product names appearing in this User's Guide may be trademarks or registered trademarks of their respective
holders. Java™ and all Java-related logos and trademarks are trademarks or registered trademarks of Sun
Microsystems, Inc. in the United States and other countries.
Support
If the unit ever needs to be repaired or serviced, the customer should contact the nearest EverFocus Electronics
Corp. Service Center for return authorization and shipping instructions.
4
EZN-Series IP Cameras
TABLE OF CONTENTS
1.
INTRODUCTION ......................................................................................................... 8
2.
FEATURES ................................................................................................................ 8
3.
NAVIGATING THE USER INTERFACE .............................................................................. 9
3.1
ACCESS VIA THE INTERNET ................................................................................................ 9
3.2
THE DEFAULT HOME PAGE (“LIVE”) OF THE CAMERA MENU ................................................. 9
4.
PLAYBACK .............................................................................................................. 13
4.1
SETTING UP THE PLAYBACK FUNCTION ............................................................................. 13
4.1.1 PREPARING THE MICRO SD CARD ............................................................................ 13
4.1.2 TESTING THE PLAYBACK FUNCTION ......................................................................... 14
4.2
5
THE PLAYBACK PAGE ....................................................................................................... 15
SETTINGS ............................................................................................................... 17
5.1
SYSTEM INFO ................................................................................................................. 17
5.1.1 SYSTEM INFO – INFORMATION ................................................................................ 17
5.1.2 SYSTEM INFO – LOG ............................................................................................... 17
5.2
USER CONFIG ................................................................................................................. 18
5.2.1 LIVE VIEW CONFIG ................................................................................................. 18
5.2.2 RECORDING/SNAPSHOT EXPORT SETTINGS .............................................................. 19
5.2.3 LANGUAGE ............................................................................................................ 19
5.3
NETWORK ...................................................................................................................... 19
5.3.1 NETWORK – NETWORK ........................................................................................... 20
5
EZN-Series IP Cameras
5.3.2 NETWORK – DDNS .................................................................................................. 22
5.3.3 SMTP / FTP ............................................................................................................ 23
5.3.4 HTTPS ................................................................................................................... 24
5.3.5 SNMP .................................................................................................................... 27
5.3.6 NETWORK ALARM .................................................................................................. 27
5.4
VIDEO ............................................................................................................................ 27
5.4.1 MULTI STREAMING................................................................................................. 27
5.4.2 CAMERA ................................................................................................................ 29
5.4.3 ADVANCED ............................................................................................................ 30
5.4.4 ROI (REGION OF INTEREST) ..................................................................................... 34
5.4.5 PRIVACY MASK ....................................................................................................... 35
5.5
AUDIO ........................................................................................................................... 36
5.6
USER.............................................................................................................................. 37
5.6.1 USER INFORMATION .............................................................................................. 37
5.6.2 IP ADDRESS FILTER ................................................................................................. 38
5.7
EVENT ............................................................................................................................ 39
5.7.1 EVENT SETTINGS .................................................................................................... 39
5.7.2 MOTION DETECTION .............................................................................................. 42
5.7.3 TAMPER DETECTION ............................................................................................... 43
5.7.4 ALARM I/O ............................................................................................................ 43
5.7.5 SCHEDULE ............................................................................................................. 43
6
EZN-Series IP Cameras
5.8
SYSTEM .......................................................................................................................... 44
5.8.1 DATE/TIME ............................................................................................................ 44
5.8.2 DAYLIGHT SAVING .................................................................................................. 45
5.8.3 SD CARD ................................................................................................................ 45
5.8.4 MAINTENANCE....................................................................................................... 46
6.
EXIT ...................................................................................................................... 47
7.
SPECIFICATIONS ...................................................................................................... 48
7
EZN-Series IP Cameras
1. INTRODUCTION
This innovative EZN Plus series camera from EverFocus is a high-performance, multi-stream, H.264, outdoor network
camera featuring HD-quality optics, infrared lighting and WDR*. This camera’s infrared lighting enables high-quality
images in the darkest of environments, while its built-in WDR* capability helps to smooth out high-contrast light
conditions and can therefore record important image details even in high-backlight conditions. The camera also
features H.264/MJPEG multi-stream output for simultaneous live monitoring and high-resolution recording. The EZN
Plus series is designed for simple installation and supports all types of outdoor/indoor mounting applications. Its tough
IP66 casing and impact resistance combines with its tampering-detection capabilities to deliver a rugged, vandal-proof
solution that can keep recording in very adverse environments.
*Note: The WDR function is only for models that are specified to have this feature.
2. FEATURES
Built-in H.264/MJPEG digital signal output at HD and megapixel resolution at up to 30fps
H.264/MJPEG multi-stream output for simultaneous live monitoring and high-resolution recording
Supports 3 independent video streams that can provide different compression formats and resolutions
Built-in network interface (10Base-T/100Base-TX) for remote monitoring by PC
Easy configuration system for various event and schedule recording conditions
One-click easy installation
True Day/Night function with IR Cut filter
Low luminance and built-in IR LEDs for better image quality at night
Wide Dynamic Range (WDR*)
Built-in Dynamic Noise Reduction (DNR)
Motion Detection and Privacy Zone Masking
IP66-rated housings for all outdoor models
One priority alarm input and one alarm output
Smart alarm reaction & resume after alarm
Digital Mirror and Flip functions
Auto IRIS control
Power over Ethernet (PoE)
Built-in Micro SDHC slot
8
EZN-Series IP Cameras
3. NAVIGATING THE USER INTERFACE
The Installation Guide included in the product packaging explains how to connect your EZN Plus series camera to your
computer or IP network via its Ethernet cable. The guide also explains how to find the camera and its IP address on the
network.
This section explains how to access the camera’s configuration menu via the Internet.
3.1
ACCESS VIA THE INTERNET
1. Start your Internet Explorer browser. (Download IE if you don’t have it on your computer. IE 7 is the most
suitable version. Please upgrade to IE 7 if you have an older version of IE.)
2. Enter the IP address or host name of the camera in the Location/Address field of your Internet Explorer
browser. (Please refer to your Installation Guide to see how you can find the IP address. You can also use the
IP Utility program that is on the included CD ROM – see the Installation Guide – to find the device on your
LAN, especially if you left the IP address dynamic, instead of changing it to a static address. If you can at
first not find the camera on your IP Utility program, restart the program and try again.)
3. If the login screen appears, input the “Username” and “Password”. The default username is “user1” and the
default password is “11111111”. Click the “Login” button.
4. You might be required to download ActiveX, which is required to view the camera feed. If asked, click "Yes".
5. You should be able to see the Live page now (see the screenshot on the right).
3.2
THE DEFAULT HOME PAGE (“LIVE”) OF THE CAMERA MENU
1. Press the
button to display the
"Live View" page (see the image on the right). Double-click
on the image to show a full-screen display, double-click
again or press ESC to return to the normal display. If you
experience video feed lag time (if connected via Internet),
you can reduce the resolution or limit the number of
streams (see the Settings > Video > Multi Streaming
section below).
9
EZN-Series IP Cameras
2. Press the
button to play recorded data directly from the on-camera Micro SD card (for
this function to become active, you have to insert a Micro SD card in the camera’s Micro SD card slot. The
Micro SD card slot can be accessed by unscrewing the front part of the camera housing dome. See the
Playback section below for more details.)
3. Press the
button to enter the Settings page. On the Settings page, there are 10
submenu sections: [System Info], [User Config], [Network], [Video], [Audio], [User], [Event], and [System]. Click
on the section buttons to open their configuration fields. See the Settings section below for more information.
4. Press the
button to exit the system and close this browser page.
5. Video Stream
Select the Video Stream (Stream 1, Stream 2 or Stream 3) that will be displayed in the video-feed screen on
the right. Stream 2 and Stream 3 will only be selectable if you have enabled these streams in your Settings >
Video > Multi Streaming setup page. The default setting is Stream 1 only. See the Settings > Video > Multi
Streaming section below for more info.
6. View Size
Use this to select the appropriate view size and shape of the video box on the right. A smaller size might
increase transmission speed and video quality.
7. Digital Zoom
Press the “+” or “-“ buttons or roll the mouse wheel to magnify / reduce the displayed image (maximum
magnification is x10). Clicking on a magnified image will re-center the image around that point.
8. Record
The record button is used to record the current video stream. The location on your computer where the image
file will be saved to can be specified in the submenu “Settings > User Config > Recording/Snapshot”. See the
User Config section below for further information. Note: The recordable segment for this function is limited to 1
minute. If you need to do long-period recording, please set a recording schedule. See the Event section below
for more info.
10
EZN-Series IP Cameras
9. Snapshot
Click the Snapshot button to save a snapshot of the video image currently being displayed. The location on
your computer where the snapshot data will be saved can be specified in “Settings > User Config >
Recording/Snapshot”. Please refer to the User Config. section in this manual for further information.
10. Play Audio / Transmit Audio
Click the “Play Audio” (speaker) and “Transmit Audio” (microphone) buttons to switch the sound on/off for the
speaker and microphone, respectively (if such external devices have been connected to the camera directly or
via the network).
11. One Push
This button can be enabled (turned from faded to clear) by following the navigation path “Setting > Video >
Advanced” and then going to the “White Balance Setting” field’s “Mode” line and selecting “One Push” in the
drop-down menu. Once this is done, pressing this button will instruct the camera to adjust the White Balance
settings of the camera, and these settings will be active until the button is pushed again. This is like a
“semi-automatic” way to adjust White Balance to suit the user, if the Auto or Manual mode does not give the
result that the user wants.
12. Manual Control – Trigger Event
Press the “Trigger Event” button to trigger an event directly from the Live page. If you have configured an event
(in the Event submenu) that will trigger a reaction (like a recording) when a Manual Trigger event occurs,
clicking this button will trigger that reaction. You can select what that reaction will be. You can, for instance, set
the camera to record the audio/video feed to the Micro SD card on board the camera. You can then click on the
Playback button to open the Playback page and search for and play all such recordings that had been stored
on the card. Such event actions will be effective once they have been configured in the “Event” menu. (Please
refer to the Event section for more details.)
13. Manual Control – Reset Alarm
Press the “Reset Alarm” button to reset the alarm output remotely.
11
EZN-Series IP Cameras
14. Lens Control
These buttons control the lens actions. Click the “++” flower icon at top left to focus
closer quickly. Click the “+” flower icon to focus closer slowly. Click the corresponding
mountain icons to focus farther quickly or slowly. Click the “++” and “+” magnifying
glass icons to zoom in quickly or slowly. Click the corresponding “- -“ and
“-“ magnifying glass icons to zoom out quickly or slowly.
15. Status Display (info lines that can be placed above video box or at bottom of page)
This shows the name of the camera that is currently active or being configured, current date/time and current
frame rate. You can activate these info displays in the Settings > User Config page (under Text Settings).
16. Event signal icons (above video area)
When an alarm or motion event is triggered, a
signal icon will appear at the top right of the Live
page to alert the user. A red “phone” icon is for an
alarm event and the remaining “running man” color
icons are for motion detection events in differently colored motion detection zones. The colors of these motion
event icons correspond to the colors of the motion trigger areas you have configured in the Motion Detection
submenu. Please refer to the Settngs > Event > Motion Detection section for detailed information about Motion
Detection setup. The red circle icon above the video screen (see the image below) will appear when the
camera is recording footage to a computer-based folder (not to the on-board SD card) as part of a
preconfigured Event (see the Settings > Event > Event Settings and Schedule sections for more info).
Right: The red circle icon above the
video screen will appear when the
camera is recording footage to a
computer-based folder as part of a
preconfigured Event (see the
Settings > Event > Event Settings
section for more info).
12
EZN-Series IP Cameras
4. PLAYBACK
Playback is designed as a quick
way to check recent recordings
that were triggered by Events
that were configured to “Record
to SD Card” in the Settings >
Event > Event Settings page.
Right: The Playback page is
only accessible once the
on-camera Micro SD card is
inserted and active (see
instructions below).
4.1
SETTING
ETTING UP THE PLAYBACK
PLAYBA
FUNCTION
The Playback function operates from a Micro SD card on board
the camera. This function will not be active until the user has
inserted such a card in the camera’s
camera’ Micro SD card slot. The card
may also have to be formatted in the Settings submenu. This card
slot can be accessed by simply unscrewing the front of the
camera housing (see the picture on the right). Remember to slide
the card in with the lettering and ridge facing upward.
upward
4.1.1 PREPARING THE MICRO SD CARD
Once you insert a functional Micro SD card into the slot, the Playback button on the Live page should
become active within seconds (see section 4.1.2 below – the grey letters should
hould turn white).
white) IF NOT, do the
following:
13
EZN-Series IP Cameras
1) From the Live page, click Settings > System > SD Card. If no card has been inserted yet, the Remove button
should be faded, indicating that no card is being detected. (If a card is inserted, and the Remove button is still
faded, pull the card out and re-insert it.)
2) Slide the card into the slot until it clicks into position.
3) The Remove button should become active within a few seconds, indicating the card is active.
4) If the Remove button stays faded, click the Format button to format the card. NOTE: All data on the disk will be
deleted if the Format button is clicked.
4.1.2 TESTING THE PLAYBACK FUNCTION
1
Once the SD card is detected by the system,
the button (inactive) will turn to
(active).
2
To test the Playback function (this is not required), set up a “Manual Trigger” Recording Event by clicking
Settings > Event > Event Settings.
3
Click the “Add” button on the middle right side of the page to open an “Add Event” box.
4
Give the event a name, like “Test 1”.
5
In the “Event Triggered by” field, click on Manual Trigger.
6
Below this, check “Enable This Event”, “Enable Post-trigger Buffer”, and “Record to SD Card”.
7
To save your settings, click OK, or close the box by clicking on the red x icon at top right of the box (in which
case you will be asked if you want to save the data, to which you should reply OK). The box will close and the
new event will be listed in the list area of the Event Settings page.
8
Look at the “Post-trigger Buffer” at the bottom to make sure the buffer time is set to 10 seconds.
9
Click “Apply” to make sure all settings are saved.
10
Click the Live button to go back to the Live page.
11
Get ready to click the Trigger Event button at the bottom of the page. Before you do, see if you can find
something in the view screen that will give you a visual time marker. For instance, if you can get your hand in
front of the camera’s lens, get ready to count down on your fingers.
12
Click the Trigger Event button and slowly count down on your fingers in front of the lens (if you are able to do
so – if not, try to find visual cues on the view screen that will help you to mark the moment you pushed the
trigger). The recording period will be as long as the buffer time you selected – the default period is 10 seconds.
13
Click the Playback button to open the Playback page.
14
EZN-Series IP Cameras
14
There are different ways to search for recording files on the camera’s Micro SD card (i.e. the Playback memory).
For a recent recording like your test event, simply click the “Search” button under the “Search by File” header.
15
If the SD card is active and formatted correctly, the recording folder’s name (the recording day’s date) will
appear in the Filename box at the bottom. Click on this folder to open it. If there are sub-folders, click on the
bottom one (the most recent would be at the bottom) until you can click on a file that cannot open to another
sub-level and shows data in the File Information box to the right. This would be the file of the most recent
recording event.
16
To play this file, click the Play button below the video box. The test footage you have recorded should start
playing. Play time should be 10 seconds if you left the Post-trigger Buffer as 10 seconds.
4.2
THE PLAYBACK PAGE
On the Live page, click the Playback button to open the Playback page (see the image on the next page).
Search by File: Click the Search button to search for all recording files on the on-camera Micro SD card.
Search results will be displayed in the Filename area.
Search by Time: Click the calendar icon and select the date and time from which you want to search
until the present moment. Click search to get your search results, which will be displayed in the Filename
area.
Search by event: Click the type of Event recordings you want to search for (Alarm, Motion, Manual
Trigger) and then click the calendar icons to select the Start Time date/time and the End Time date/time
of your search. Click Search to get your search results, which will be displayed in the Filename area.
Multiple Files: Check this box if you want the video player to play all the files in the selected folder. The
files will be displayed in the Filename
area.
Loop Again: Check this box if you want
the video player to play the selected file
over and over again.
Filename: This area will display a list of
search results (recording files and folders).
Folders will be displayed first. Click on the
folder and click on each subfolder until the
recording files in that folder is listed. Files
15
EZN-Series IP Cameras
can be recognized by clicking on them – clicking on a file will display the file’s information in the File
Information area.
Play: Once you have opened the file’s folder and have clicked on the file to highlight it, its details will be
displayed in the File Information area. You can now click Play to play that specific file.
Stop: Click this button to stop the playback.
Copy: Click this button to copy the selected file to the computer-based folder of your choice. A browsing
box will open so that you can search for the folder of your choice.
Lock: Click this button to lock the selected file. This will protect that file from being overwritten during any
overwrite procedure. The file will thus be saved on the SD card indefinitely. However, the file will still be
deleted if the SD card is ever formatted.
Remove: Click this button to delete the selected file.
16
EZN-Series IP Cameras
5
SETTINGS
Click the Settings button on the Live page
to enter the settings menu.
Right: Clicking the Settings button will open
the Settings submenu column on the left,
and display on the right whichever of these
submenu pages have been selected by
clicking on the related submenu’s button on the left. The default selected submenu is the top one, System Info.
5.1
SYSTEM INFO
The System Information and System Log can be checked on this page. Click the top tab of the one you want to see.
5.1.1 SYSTEM INFO – INFORMATION
These values cannot be
changed on this page, and
are for reference only.
5.1.2 SYSTEM INFO – LOG
System Log:
Number/Date/Time: Displays
the sequence number, date
and time of the log event.
Log message: Contains all
information and event
messages, including Login, the User’s IP, Reboot, Firmware Upgrade, Load Factory Default, Configuration
Reset and Events Detected. The log will display the last 256 log events.
17
EZN-Series IP Cameras
Click the Export button to export the system log event list into a “.txt” file and select the location where the
exported log file will be saved to.
5.2
USER CONFIG
Each user can set a different configuration for his/her Live page here. These settings will be applied to the logged-in
user’s Live page every time he/she logs in.
5.2.1 LIVE VIEW CONFIG
Video/Audio Connection Protocol Setting: If needed, select the protocol that applies to your connection setup.
Click Apply to apply the changes
or Reset to reset without saving
the changes.
Text Settings: Check the box of
each option (Machine name,
Date/Time, Frame Rate) to display
this info on the Live page screen.
Foreground Color: Slide the Red,
Green and Blue bars to create your
preferred text color for the info text
line.
Position: Select the position where the text will be displayed. Choose from Upper Left / Lower Right / Lower Left.
Click Apply to apply the changes or Reset to reset without saving the changes.
Date/Time Format Used in Text: Click the dropdown menu to select date/time format from the listed options.
Click on the desired hour format. Click Apply to apply the setting changes or Reset to reset without saving the
change.
Live View Layout Settings: Check the “Show Lens Control Buttons” and “Show One Push Buttons” boxes if you
want to show these buttons on the Live page. Uncheck these boxes to hide these buttons.
18
EZN-Series IP Cameras
5.2.2 RECORDING/SNAPSHOT EXPORT SETTINGS
This configures where your Record Button and Snapshot Button (
) files will be saved if you click
one of these buttons. Selectable folders will be on the computer only, not on the on-camera Micro SD card.
Enable Event Recording to PC: Checking this box will let the system save Record/Snapshot Button recordings to
the folder configured below on the user’s PC.
Export Folder: Select the Export folder for the action above by clicking on the browse (…) button, then select the
desired folder on your computer for saving to.
File size: The user can limit the size of each recorded file here (in minutes). When a single recording file exceeds
the time you set, the system will create a new file to save that data to.
Overwrite: Select “ON” for overwriting recording/snapshot file when the disk storage capacity is full. The user can
set the storage capacity limitation in the in-sentence field in the gray box below the Overwrite setting: “If the
remaining hard disk capacity is less than ____ MB (50~2000), system will stop recording or start overwriting. “
Click Apply to apply the setting changes or Reset to reset without saving the changes.
5.2.3 LANGUAGE
Select the language to be displayed on the web pages of this GUI. The default language is English. To add a new
language not listed in the current Language list, click the Browse button to locate the new language file (.evb) on
your computer and then click the Upload button. Updated language files might be available on the manufacturer’s
website. Contact your vendor if required.
Click Apply to apply any changes or Reset to reset without saving the changes.
Note: Uploading a new language file will cause the system to reboot automatically. Please create a new
network connection to the IP camera when the reboot is complete.
5.3
NETWORK
This page covers network-related settings, including Network, DDNS, SMTP/FTP, HTTPS, SNMP, and Network
Alarm.
19
EZN-Series IP Cameras
5.3.1 NETWORK – NETWORK
The following information is required to configure the network settings. Contact your network administrator or your
internet service provider to get the info.
IP Settings:
IP Type
Refer to the network administrator for these settings of the server. Default: DHCP
DHCP: This setting lets the system use an automatically assigned (dynamic) IP address. This address can change
under certain circumstances. For instance, when the camera’s network switch/hub has to be rebooted. Do not assign
to the DHCP server the same IP addresses used for the other network cameras and PCs with unique IP addresses.
Static IP: The user can manually set the Static IP address. This type of address is stable and cannot change, but
the user has to make sure there are no address conflicts with other network-connected devices.
PPPoE: This is a DSL-connection application. The ISP will ask the user to input a username and password. Contact
your ISP for these details.
Note: If PPPoE is selected as the IP type, the supplied IP Utility program will not be able to detect the
device.
IP address
When DHCP is not used, the user needs to manually enter the IP address of the camera. Do not enter an IP
address that is already used for your computer or other network cameras.
20
EZN-Series IP Cameras
Subnet Mask
This field is used to set the netmask for your network, so that the IP camera will be recognized within the network.
Example: 255.255.255.0. When DHCP is selected, the DHCP server will assign this value automatically.
Gateway
This field is used to set the gateway for your network so that the IP camera will be recognized within the network.
When DHCP is selected, the DHCP server will assign this value automatically.
Primary DNS
Enter the IP address of the DNS server if this is provided by an ISP.
Secondary DNS
If your ISP provided you with a secondary DNS address, please enter it here.
Username
Enter the account’s username (used only for PPPoE).
Password
Used only for PPPoE.
IPv6
Enter the IPv6 details in this area, if this applies to your system.
Click Apply to apply the setting changes or Reset to reset without saving the change.
Port Settings: Enter the HTTP and RTSP port numbers and click Apply to save.
Multicast Settings: Enable if required, fill in the setting options and click Apply to save.
21
EZN-Series IP Cameras
5.3.2 NETWORK – DDNS
DDNS settings
DDNS is necessary
when accessing the
camera via the
Internet from a
network environment of which the global IP address is obtained by using DHCP. To use the DDNS function, it is
necessary to connect to a dedicated DDNS server. We support these four DDNS server providers:
www.everfocusddns.com, www.sitelutions.com, www.dyndns.com, and www.no-ip.com
Enable: Check this box to enable the DDNS function.
Service ISP: If you choose the EverFocus DDNS server, you can obtain a free account name from EverFocus
“www.everfocusddns.com”. Just enter your desired camera name in the textbox in the following sentence, and then
click the Register/ Update button to register it.
If you wish to get a domain name from one of the other three DDNS providers that are listed in the lower area, please
register your name with that provider, then check that provider’s button and fill in that domain name’s Record ID,
FQDN, Username and Password on this GUI page. Refer to the specific DDNS company’s website for further
information about the DDNS.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
22
EZN-Series IP Cameras
5.3.3 SMTP / FTP
Set SMTP Server (email)
This area is for configuring the mail server that is used to send e-mail notifications from the camera to predefined
addresses via SMTP.
SMTP Server: Enter the IP address or the host name of the SMTP server used to send e-mails.
SMTP Port: Enter the port number for SMTP. The default is 25.
Authentication: Check this box if the SMTP server requires authentication (user/password).
User name: Input the user’s login ID if the SMTP server requires authentication.
Password: Input the user’s login password if the SMTP server requires authentication.
Receiver Address: Input the e-mail addresses for receiving an e-mail message when an EVENT is enabled and
triggered. Please use “;” to separate multiple addresses.
Sender Address: Input the sender’s e-mail address, so that the receiver can recognize the sender when an Event
message is received.
Send Test Email: Click the
button to send a testing email to the assigned address.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
23
EZN-Series IP Cameras
Set FTP Server
The settings relating to the FTP server used to transmit the alarm images can be configured here.
FTP Server: Enter the IP address or the host name of the FTP server.
FTP Port: Enter the port number for the FTP server. Default is 21.
Recording Path: Assign the recording path.
User Name: Set FTP User’s name.
Password: Set FTP password.
PASV mode: Check to enable Passive mode. Passive mode is normally enabled. If a connection cannot be
established, uncheck "PASV Mode”.
Test FTP Server: Click the
button to send a testing file to the assigned FTP server.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
5.3.4 HTTPS
Hypertext Transfer Protocol Secure (HTTPS) is a combination of the Hypertext Transfer Protocol and the
SSL/TLS protocol and provides encrypted communication and secure identification of a network web server.
To use HTTPS, a Certificate must be created first. There are two ways to create and install a certificate:
24
EZN-Series IP Cameras
Create Self-signed Certificate: A self-signed certificate can be used until a Certificate Authority-issued certificate
has been obtained. Click the
button to install a self-signed certificate.
Although self-signed certificates are free and offer some protection, true security is only implemented after the
installation of a signed certificate issued by a certificate authority. Enter the required Certificate information as shown
below. This info will be displayed on the certificate if anyone wants to inspect it. Enter all required information and
click Apply to save it.
Create Certificate Request: An official certificate can be requested from an issuing Certificate Authority by clicking
the
button. Enter all the required info and click Apply to save and send the
request.
Created Request: This field will show the Subject field of the created request (see below)
The properties of any current certificate request can be viewed by clicking the Property button in this field.
25
EZN-Series IP Cameras
The image on the right shows an example of the “Property”
box of a certificate request.
To create and install another certificate or request, remove
the existing one by clicking the Remove button to erase the
certificate or request.
Install Signed Certificate:
When the signed certificate is sent back to you from the Issuing Authority, download it on your computer. Then click
the Browse button in this field to search for the file. Click on the file and press the Upload button to import the
certificate.
Installed Certificate Information:
Once a certificate has been uploaded, this field will show the subject line of the certificate (see the example below).
Press the Property button to view the details of the certificate. A pop-up window will appear with the information
(below is an example of the Property pop-up window of a self-signed certificate).
To create and install other certificates, remove the existing one by clicking the Remove button to erase the
certificate.
26
EZN-Series IP Cameras
5.3.5 SNMP
The default values for
SNMP v1/v2/v2c and
SNMP v3 are already filled
in. Click either of the
Enable buttons to enable
either of the two. Make
your changes as desired.
Click on the Trap Address
field to enter the digits, if
required.
5.3.6 NETWORK ALARM
Set Network Alarm
This function works with
PowerCon software, for
the setting details, please refer to the PowerCon network alarm protocol.
5.4
VIDEO
The settings relating to video such as streaming, camera OSD can be configured on this page. The "Video" page
has two tabs: Multi-streaming, Camera, Advanced, ROI and Privacy Mask.
5.4.1 MULTI STREAMING
27
EZN-Series IP Cameras
Stream Settings
This IP camera can output
three video streams
simultaneously. For each of
these streams, the user can
set the compression format,
resolution, bit rate, and
frame rate individually.
Stream 1 is always enabled
for live view.
To enable Stream 2 and/or Stream 3, check the “Enable” box the header of each stream.
NOTE: If you connect to the camera via the Internet and experience a delay (lag time) in the video feed, try to
reduce the number of streams and the quality and resolution of the streams – but keep the frame rate at its
maximum (30fps).
Format: Select the encoding format – H.264 or MJPEG.
Resolution: Select the most suitable resolution for your needs.
Frame Rate: Select from 1 to 30 fps.
If required, select whether you want the stream to stream a Constant Bit Rate or a Variable Bit Rate, and set the
values of whichever option you choose.
Click Apply to apply the setting changes or Reset to reset without saving the changes.
Video Recording Settings
Select the stream you want to configure and then select whether you want the recording files of that stream to be
saved in AVI or ARV format.
Time Stamp Settings
28
EZN-Series IP Cameras
You can select the Date/Time format, position, and add the setting to the streaming.
Click Apply to apply the changes, or Reset to reset without saving the changes.
5.4.2 CAMERA
Lens Control: Set the Zoom, Focus,
and Digital Zoom actions of your
camera.
Image Settings: Set the Brightness
and Sharpness of the image.
Camera Settings:
Mirror: Switch Mirror ON to rotate the
image horizontally around a vertical
axis.
Flip: Switch Flip ON to rotate the image vertically around a horizontal axis.
AE: ALC = Selecting Automatic Light Control allows the camera circuitry to either take bright spots more into
consideration (peak), bringing out detail in bright areas, or less into consideration (average) bringing out detail in
shadows. AES = Selecting Auto Electronic Shutter disables the Shutter setting below this setting. In this mode, the
camera measures the light level and decides whether it needs more or less light and then automatically adjusts the
shutter speed accordingly.
BLC: Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against a bright
background.HLC (Highlight-Suppression BLC) is used to reduce the brightness of light sources in a specific area. It is
activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights,
street lights or headlights in the field of view. Whereas BLC can increase the exposure of a dark area surrounded by a
brighter area, HLC can decrease the exposure of bright areas surrounded by darker areas. This enables the camera to
better display information that would otherwise have been “whited out”, like a license plate between two bright
headlights on a dark road.
29
EZN-Series IP Cameras
Select OFF to switch Back Light Compensation functions off. Select ON(BLC) to activate the BLC function. Select
ON(HLC) to activate Highlight-Suppression BLC.
WDR: D-WDR corrects the exposure when the contrast between light and dark in an image is extreme. Test the
different levels to find the one that works best for your light conditions.
Switch this function off, or select the level at which it will operate.
D/N Mode: Select “Auto” to let the camera automatically switch to Night mode (Black&White) when the light levels fall to
a specified level, and back to Day mode (Color) when the light levels rise to a specified level. Select “Day” to keep the
camera in Day mode (Color), even in nighttime. Select “Night” to keep the camera in Night mode (B&W), even in
daytime.
5.4.3 ADVANCED
Note: The Advanced settings for the 1 megapixel EZN3160 will be listed first, after which the additional settings
of the 2 megapixel EZN3260 and then the 3 megapixel EZN3340 will be listed.
Camera Settings (EZN3160):
Exposure Settings (AE):
This setting is used to adapt to the
amount or type of light used by the
camera.
Mode:
ALC: Selecting Automatic Light
Control allows the camera
circuitry to either take bright spots
more into consideration (peak), bringing out detail in bright areas, or less into consideration (average) bringing out
detail in shadows.
AES: Selecting Auto Electronic Shutter disables the Shutter setting below this setting. In this mode, the camera
measures the light level and decides whether it needs more or less light and then automatically adjusts the shutter
speed accordingly.
30
EZN-Series IP Cameras
Iris: Specify the size of the Iris opening here.
Shutter: If enabled, this setting lets you set the shutter speed yourself (measured in fractions of a second).
Shutter Limit: Use this setting to set the maximum shutter speed for the camera.
AGC Limit: Set the Auto Gain Control limit here.
Brightness: Set the image brightness here.
BLC Settings:
Back Light Compensation (BLC) is used to make the subject appear clearer when it is set against a bright
background.HLC (Highlight-Suppression BLC) is used to reduce the brightness of light sources in a specific area. It is
activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights,
street lights or headlights in the field of view. Whereas BLC can increase the exposure of a dark area surrounded by a
brighter area, HLC can decrease the exposure of bright areas surrounded by darker areas. This enables the camera to
better display information that would otherwise have been “whited out”, like a license plate between two bright
headlights on a dark road.
Mode: Select OFF to switch Back Light Compensation functions off. Select ON(BLC) to activate the BLC function.
Select ON(HLC) to activate Highlight-Suppression BLC.
Level: Select the level of whatever option you selected in the field above.
3D-DNR Settings:
This limits the amount of digital “video noise” that is usually found in any video stream, and helps to reduce file size.
The higher the level, the more the reduction.
Mode: Select OFF to switch the 3D-DNR function off. Select ON to activate the function. Select AUTO to activate
automatic 3D-DNR.
Level: Select the level of whatever option you selected in the field above.
D-WDR Setting:
D-WDR corrects the exposure when the contrast between light and dark in an image is extreme. Test the different
levels to find the one that works best for your light conditions.
Switch this function off, or select the level at which it will operate.
31
EZN-Series IP Cameras
Note: When D-WDR is ON, some parts of the image may appear solarized. This is normal for WDR, and is not a
camera malfunction.
White Balance Settings:
Select the mode that delivers the best quality image for the camera’s light environment. In the Auto mode the camera
computes the white balance value output using color information from the entire screen. It outputs the proper value
using the color temperature radiating from a black subject based on a range of value from 3000 to 7500K. In Indoor
mode the camera uses 3200K as the base value. In Outdoor mode it uses 5800K as the base value.
Mode: Select “Auto” to let the camera automatically adjust the White Balance.
Select “Manual” to adjust the Red and Blue values yourself in the fields below this field. Select “Indoor” to use the
default settings for indoor environments. Select “Outdoor” to use the default settings for outdoor environments.
Select “One Push” to enable this function’s button on the Live page – this will allow you to force the camera to
readjust the white balance every time you push the “one Push” button on the Live page. The lens will hold the
same focal position until the next trigger command is received. This function helps to prevent incorrect focusing in
dark environments.
Day/Night Settings:
Mode: Select “Auto” to let the camera automatically switch to Night mode (Black&White) when the light levels fall to a
specified level, and back to Day mode (Color) when the light levels rise to a specified level. Select “Day” to keep the
camera in Day mode (Color), even in nighttime. Select “Night” to keep the camera in Night mode (B&W), even in
daytime.
Sharpness:
Select the sharpness level of the image. A low sharpness level will deliver a softer, less detailed image. A high level will
deliver a sharp, highly detailed image.
Mirror:
Switch Mirror ON to rotate the image horizontally around a vertical axis.
Flip:
Switch Flip ON to rotate the image vertically around a horizontal axis.
32
EZN-Series IP Cameras
Monitor Type:
If you are experiencing image quality problems on your monitor, it could be because the camera is not synchronized
with the type of monitor you are using. Select either Set 2 or Set 3 and click Apply to see if the image quality improves.
Click Apply to save all changes. Click Reset to cancel all changes.
Additional Camera Settings (EZN3260):
Lens (IRIS Control): Choose between DC and Manual lens types, depending on the lens that has been attached
to the camera.
Slow Shutter: This option can be switched on if the Shutter (speed) setting is 1/30. Setting options range from x2
to x60.
Visibility Enhancement: (OFF/Low/Middle/High) Images in foggy or rain environments or in environments with a
very strong luminous intensity have a dynamic range that is significantly lower than ordinary images. The user
can use this Visibility Enhancement setting to “DEFOG” the image if such “FOGGING” is an issue.
Negative: Switch this setting ON to view a color negative version of the video image. This is useful at night or
when viewing temperature-sensitive images.
Color Suppression:
Edge Color Suppression: False color can be created on the edges of the video image. In such conditions, you can
switch Edge Color Suppression ON to reduce the false color.
Highlight Color Suppression: False Color can happen quite often when it is too bright or too dark. Switching this
setting ON will suppress all colors that are brighter or darker than a predetermined value.
Monitor Settings: The user can use this field to optimize video quality for his or her specific type of monitor – LCD
or CRT.
Color Space Standard: The options are YUV601 and YUV709. These define the color space standard required to
convert an RGB picture to a YUV picture. Generally, YUV601 is used for Standard Definition (720P) devices
and the YUV709 is used for High Definition (1080P) devices.
33
EZN-Series IP Cameras
Additional Camera Settings (EZN3340):
Flickerless: If the Mode field in the Exposure Settings (AE) area has been set to AES, then this option becomes
available. Choose between OFF, 50HZ, and 60HZ.
Suppress Function:
Aperture Compensation Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress
luminance noise when the AGC level increases.
Chroma Suppression: (OFF/Low/Middle/High) This setting can be activated to suppress chrominance noise
when the AGC level increases.
5.4.4 ROI (REGION OF INTEREST)
A Region of Interest is an on-screen area that is streamed at higher definition/quality than the areas around it. It
allows you to choose which parts of the camera view are the most important. Use this page to configure up to 8
ROIs and select the quality level at which each of these would be streamed.
ROI Settings
1. Click the ROI No. field’s down area and select a number/ID for the ROI you want to add.
2. If you click the Add button, your mouse cursor will turn into a pen when you hold it over the setup screen on the
left.
3. Move your mouse pen to the position where you want your ROI rectangle to start. Click on that position and
move your mouse pen to the position (diagonally opposing corner) where you want your ROI rectangle to end.
34
EZN-Series IP Cameras
4. Click again and the setup screen will display the rectangular area you selected with the ROI number/ID inside it.
5. Click on the Quality bar and slide it to the High or Low direction, depending on the quality that ROI should be
streamed at.
6. Click Apply to apply the changes, or click Reset to reset without saving the changes.
5.4.5 PRIVACY MASK
Use this page to configure up to 4
Privacy Masks.
Privacy Mask Setting
Mode: Click Color to make the masks
appear as colored rectangles on the
screen. Click B/W to make the masks
appear as gray rectangles on the
screen. Click Mosaic to make the
masks appear as translucent mosaic
blocks on the screen.
Level: Select the color of the masks if you selected Color in the field above. Select the level of grayness (0~15) of
the masks if you selected B/W in the field above. Select the size of the mosaic blocks if you selected Mosaic in the
field above (the larger the blocks, the more the masking effect).
Click Apply to apply the changes, or click Reset to reset without saving the changes.
The Color Palette: Click on the turquoise palette block to select this color for your block selection pen. When you
hover your mouse cursor over the image now, the mouse cursor will turn into a pen of this color. Move your mouse
pen to the position where you want your mask rectangle to start. Click on that position and move your mouse pen to
the position (diagonally opposing corner) where you want your mask rectangle to end. Click again and the setup
screen will display the rectangular area you selected in the color you selected (see the image above). If you want to
create another mask, use one of the other three palette colors.
Select All: Click this button to select the whole screen for masking.
Clear All: Click this button to clear the screen of all masks.
35
EZN-Series IP Cameras
Eraser: Click this button to turn the mouse cursor into an eraser when placed on the video image. When you click
on a configured mask with this eraser, the mask will be deleted.
Area: These are the color codes and number codes of each mask, which only become applicable if a mask of that
color has been configured above.
Enable: Click the box under each color code to activate the mask of that color – if a mask of that color has been
configured above.
Click Apply to apply the changes, or click Reset to reset without saving the changes.
5.5
AUDIO
This camera can transmit audio to your computer if you have connected an external microphone to its audio Input cable.
It can also receive audio input from you and transmit it via an external speaker, if you have connected such a speaker
to its audio Output cable.
Check the Enable Audio box to enable the camera’s audio function. The camera will now act as a digital bridge (via the
IP network) between any connected audio input device and any connected audio device.
Adjust the Audio Input Volume if you have external audio input devices (microphones) connected to the camera and if
there are problems with the sound input being too low or high.
Click Apply to save all settings, or click Reset to cancel.
36
EZN-Series IP Cameras
5.6
USER
5.6.1 USER INFORMATION
The system administrator can create up to 10 user accounts on this page.
There are three different authority levels:
• Supervisor/Administrator: The only difference between a supervisor and administrator is that a supervisor can
edit an administrator’s account and password, but an administrator cannot edit the supervisor’s account and
password. Multiple administrators can be configured, but there can be only one supervisor. The supervisor and
administrators all have unrestricted access to the Settings submenus and can determine the registration of all other
users.
• User: A user can view the Live View page and view the system, network, video, and audio information. A user can
only adjust the User Config page settings. The user does not have access to the User, Event and System pages.
• Guest: The lowest level of access, which only allows the user access to the Live View page.
Add: Click this button to open the Add User window (see the image on the right). Enter the Account (e.g. user1),
Description (e.g. Mike), Password (for the new account) and Confirm (password again). Select the user’s authority level
(ADMIN, USER, or GUEST – only one user can be the Supervisor). At Status, select whether to activate or disable the
user account. Switch SD Card Playback ON if you want the user to have access to the
Playback function that plays recordings from the on-camera SD card.
Click OK to save all settings, or click Cancel to cancel.
Modify: Click this button to edit the selected user’s account details.
Remove: Click this button to remove the selected user’s account.
Click Apply to save all settings, or click Reset to cancel.
37
EZN-Series IP Cameras
5.6.2 IP ADDRESS FILTER
Use this page to specify IP addresses
that are allowed to access this camera,
and IP addresses that are not allowed
to access it.
NOTE: By default, any IP address can
access the camera, the Allowed List
addresses only become relevant when
the Denied List contains a network or
range, and the supervisor wants to
allow one or more IP addresses within that excluded range or network. In such a scenario, the user would enter the
excluded range or network in the Denied List, and enter the exceptions in the Allowed List.
Click the Allowed List button and then click the Add button to open the User IP Address Filter page (see the image on
the right). Enter the Allowed address’s details – IP Type, the Rule (Single, Network, or Range), and the IP Address.
Click the Denied List button and then do the same to add a Denied address.
Click OK to save all settings, or click Cancel to cancel.
Modify: Click this button to edit an existing entry (select the entry from the Allowed or Denied list).
Remove: Remove the selected entry.
Anonymous Viewer Login: Check this box to allow anonymous viewers to log into the camera. WARNING: TO
PROTECT YOUR CAMERA FROM BEING TAKEN OVER BY UNAUTHORIZED PERSONS, MAKE SURE THE
‘ANONYMOUS VIEWER LOGIN’ BUTTON IS NOT CHECKED/SELECTED.
Click Apply to save all settings, or click Reset to cancel.
38
EZN-Series IP Cameras
5.7
EVENT
Use this submenu’s
categories to set up
different types of events
(different types of triggers
that will trigger different
types of reactions).
Configurable events are
Motion Detection, Tamper
Detection, Scheduled
Recording,
Manual Trigger, and
alarms created by external sensors connected via the camera’s Alarm Input.
5.7.1 EVENT SETTINGS
Event List:
This lists the already configured events. Check the box next to each list to activate or deactivate the event. Click on an
event to highlight it and select it.
Add:
Click this button to open the Event configuration window (see the image below) and add a new Event that will tell the
camera to trigger a selectable reaction/s if this type of Event occurs. In the window, give the Event a name, and click
the down arrow in the “Event Triggered by” field to select the type of event that will trigger the to-be-specified
response/s:
The “Event Triggered by” options are:
39
EZN-Series IP Cameras
Alarm Input: Select this if you want a reaction trigger coming from any external, connected sensor to activate a
to-be-specified-below reaction/s via the camera system. Make
sure that a suitable device is actually connected to the alarm
input relay. See the Alarm I/O section for info on how to set up
the alarm input and output channels.
Manual Trigger: Select this option if you want the to-be-specified
reaction/s to be triggered manually (by clicking the Trigger Event
on the Live page).
Motion Detection: Select this option if you want motion in a
specified part of the camera’s viewing rectangle (the screen
image) to trigger the to-be-specified-below reaction/s. See the
Motion Detection section below for info on how to set up Motion
Detection areas.
Tampering Detection: Select this option if you want the camera’s
tampering detection sensor to trigger the to-be-specified-below reaction/s. See the Tamper Detection section
below for info on how to set up Tampering Detection.
Schedule Recording: Select this option if you want the Schedule Recording periods configured in the recording
schedule (the Settings > Event > Schedule page) to activate this event. See the Schedule section below for info
on how to set up recording schedules. In this scenario, a preconfigured event reaction like a log entry (“Log”) will
list the start and end times of each period. Actual recording will only be triggered if the event is preconfigured to
do so.
Click Enable This Event to activate the event.
Click Enable Re-trigger to set a minimum time after the event is triggered before the event can be triggered
again.
Click Enable Pre-trigger Buffer if you want the Event reaction (as selected in the “Notification Over” field below)
to be the activation of the video recording function, and if you want the recording to include the video feed from
the time period (configurable on the previous “Event Settings” page) just before the Event trigger occurred.
40
EZN-Series IP Cameras
Click Enable Post-trigger Buffer if you want the Event reaction (as selected in the Notification Over field) to be
the activation of the video recording function, and if you want the recording to include the video feed from a time
period (configurable on the Event Settings page) just after the Event trigger occurred.
The “Notification Over” (Event Reaction) options are:
Log: Check this box if you want the camera to list the event’s details in its log if the event is triggered.
Trigger Alarm Output: If you want the camera to relay the event reaction to a device attached to the alarm relay
output wire, then check this box and the box of the relevant alarm output channel. Also set how long the alarm
output signal will be sustained.
Send Mail Notification: Check this box if you want the camera to send an Event notification email to the email
address entered in the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event occurs.
Upload to FTP: Check this box if you want the camera to upload recorded footage to the FTP server entered in
the Set SMTP Server(email) field of the Network > SMTP/FTP page, if the Event occurs.
Record to SD Card: Check this box if you want the camera to start recording its video feed (when the event occurs)
on an on-camera Micro SD Card (if such a card has been inserted).
NOTE: The recording will only be as long as the combined Pre- and Post-trigger Buffers, so make sure you enable at
least one of these buffers, especially the Post-trigger Buffer.
Record to PC: Check this box if you want the camera to start recording its video feed (when the event occurs) on
the same folder on the same PC as configured on the User Config > User Config page (if such a folder has been
enabled and configured).
NOTE: The recording will only be as long as the combined Pre- and Post-trigger Buffers (and for as long as the event
trigger is happening – e.g. a motion is detected), so make sure you enable at least one of these buffers, especially the
Post-trigger Buffer.
Network Alarm: Check this box if you want the camera to send a network alarm signal (when the event occurs) to
the servers configured on the Network > Network Alarm page (if such a configuration has been completed).
Click OK to save all settings, or click Cancel to cancel.
Modify: Click this button on the Event Settings page to edit an existing Event’s settings. Highlight the desired event on
the list before clicking this button. See the section above for info on the setting options.
41
EZN-Series IP Cameras
Remove: Click this button to delete an existing, selected Event.
Click Apply to save all settings, or click Reset to cancel.
Pre/Post Trigger Settings:
Select the duration of each buffer. This will determine the amount of footage (length of time) before or after the event
trigger moment that will be included in an event-triggered video recording, if that buffer and video recording has been
enabled in the event’s configuration window.
Click Apply to save all settings, or click Reset to cancel.
5.7.2 MOTION DETECTION
Use this page to configure up to four areas in which motion will be detected. This function can be linked with correctly
configured Events to trigger Event reactions like the activation of video recording periods, snapshots, alarms, etc.
Color tabs: Click on a color tab to turn your mouse cursor into a pen of that color. You can now create a block of that
color on the video screen. Move your mouse pen to the position where you want your detection rectangle to start. Click
on that position and move your mouse pen to the position (diagonally opposing corner) where you want your mask
rectangle to end. Click again and the
setup screen will display the rectangular
area you selected in the color you
selected (see the image above).
This block will be an area inside which
the camera will detect motion. If you
want to create another detection area,
use one of the other three palette colors.
Each color denotes a different detection
area. Only one block per color is
allowed. As the number of colors suggests, you can configure up to four blocks.
Select All: Click this button to select the whole screen and thus turn the whole screen into a motion detection area.
Clear All: Click this button to delete all configured motion detection blocks.
42
EZN-Series IP Cameras
Eraser: Click this button to turn your mouse cursor into an eraser to delete any block you click on.
Area: Shows the color and number/ID of the block.
Enable: Check this box to enable the related motion detection block.
Sensitivity: Set the sensitivity of the motion detection sensor function.
Click Apply to save all settings, or click Reset to cancel.
5.7.3 TAMPER DETECTION
Use this page to set the number of
seconds that an alarm signal will be
active if the device is tampered with.
5.7.4 ALARM I/O
Use this page to set the type of
trigger input and the type of
output contact for each of the
camera’s two configurable
alarm channels.
5.7.5 SCHEDULE
Use this page to configure a schedule for periods during which the camera should deactivate all user-activated Events
(gray Deselect periods), or when the camera should deactivate all user-activated Events, except Schedule Recording
(SR) events (blue Schedule Recording-only periods), or when the camera should deactivate only SR events (red Event
Recording-only periods), or
when it should enable all
43
EZN-Series IP Cameras
activated Events (yellow periods).
Event Recording: Click this button to make every hour block you click on red. A red block represents an Event
Recording-only block, which represents an hour when the camera will deactivate all preconfigured, activated Schedule
Recording events and keep all the other activated events active.
Schedule Recording: Click this button to make every hour block you click on blue. A blue block represents a Schedule
Recording-only block, which represents an hour when the camera will deactivate all other preconfigured, activated
events and keep only the preconfigured, activated Schedule Recording events active.
Event + Schedule: Click this button to make every hour block you click on yellow. A yellow block represents an hour in
which all activated events, including Schedule Recording events, will be active.
Deselect: Click this button to make every hour block become grey. A grey block represents an hour in which all
activated events, including Schedule Recording events, will be inactive.
Click Apply to save all settings, or click Reset to cancel.
5.8
SYSTEM
Use this submenu’s submenus to set the system’s time and Micro SD card settings, and to do maintenance and reset
actions like reboots and upgrades.
5.8.1 DATE/TIME
Machine Name Settings: If required,
enter a new name for the machine. This
name will be visible in the Machine
Name field of the IP Utility software that
comes with the product (see below).
Set Time Zone: Set the time zone of the
camera’s location.
44
EZN-Series IP Cameras
Set Date/Time Manually: Set the date/time here if you won’t be using an NTP server to update the date/time (see
below).
Set Date/Time Sync.: Enter the Network Time Protocol server, if applicable. The camera’s time will be automatically
adjusted by synchronizing with the NTP server.
Click Apply to save all settings, or click Reset to cancel.
5.8.2 DAYLIGHT SAVING
Click the button to enable this
schedule, and select the dates
when the region’s daylight
saving period begins and ends.
5.8.3 SD CARD
Use this page to prepare the system for safely removing the Micro SD Card from its slot (see the image below).
Set up the SD Card
Notification: Select the percentage of storage space that should be
left on the card before the camera notifies you of the impending storage
shortage or overwrite.
Event Recording: Select if you want Event Recording only, FTP
Backup only, or both.
45
EZN-Series IP Cameras
Overwrite: Click ON if you want the card to start writing over recorded footage when its memory is full. Click OFF if
you want the card to stop recording new footage when its memory is full.
SD Card Utility
Capacity: This shows you how much card memory has been used and how much memory capacity remains on the
card.
Remove: Click this button before removing the card from the system.
Format: Click this button to Format the card. All data saved on the SD card will be removed if the card is formatted.
5.8.4 MAINTENANCE
Maintenance Server
Reboot: Click this button to reboot
the unit without changing any of the
settings. Use this function if the unit
is not behaving as expected.
Restore: Click this button to restart
and reset most of the current
46
EZN-Series IP Cameras
settings to their factory default values. The only settings that will not be changed to default are:
•
IP settings
•
DDNS settings
Default: The Default button should be used with caution. Pressing this button will return all of the camera's settings,
including the IP address, to the factory default values. The camera will then have to be reconfigured.
Save/Load Configuration Server
Save: To make a backup file of the machine’s current configurations, press Save to save all the configurations to a
config. file. This will enable the user to reload these configuration settings if the settings are changed and there is
unexpected behavior.
Load: To load a previously saved configuration, press the Browse button to locate the saved config. file (see above)
and then click the Load button. The system’s settings will be restored to the saved configuration.
Upgrade Firmware
Click the Browse button to find a previously prepared firmware upgrade file. Click Upgrade to install the new
firmware.
Note: Do not disconnect power to the unit during the upgrade sequence. The unit will reboot automatically after the
upgrade has completed. (1-5 minutes.)
Note: During the upgrade process, all event recording actions will be stopped. Event recording actions will resume
after the camera is rebooted.
6. EXIT
Click this button to exit from the system and close the web page.
47
EZN-Series IP Cameras
7. SPECIFICATIONS
GENERAL
Pickup Device
EZN3160
EZN3260
EZN3340
Image sensor
1/3" Panasonic 1.3Mega HD
progressive scan CMOS
sensor
1/3" Panasonic 2Mega HD
progressive scan CMOS
sensor
1/ 2.8" Sony 3Mega HD
progressive scan CMOS
sensor
Vari-focal lens, Auto Iris, 2.8-10mm, F1.3, 19
Lens
Horizontal : Wide 100° / Tele 27°
Angle of view
Vertical : Wide 73° / Tele 20°
Min. Illuminations
0 Lux/F=1.3 (IR LEDs on)
Day/Night
Built-in Auto IR cut filter
Shutter Time
1/125 ~1/60,000 sec.
Video Compression
Max. Resolution
IRIS Control
Video Streaming
H.264/M-JPEG
1280 x 1024
1944 x 1092
2048 x 1536
Electrical IRIS/Lens IRIS (DC Lens)
Multi-stream H.264, and Motion JPEG: 1 stream in max. resolution at 30 fps; more streams if
identical or limited in frame rate/resolution
Image Settings
Compression, Brightness, Sharpness, Contrast, Saturation, Hue, White balance, Exposure
control, Backlight compensation, Rotation, Mirroring of images, Text and image overlay
WDR
Yes(only EZN3160/3260)
AUDIO
Audio Compression
G.711
Operation Mode
Two-way audio
48
EZN-Series IP Cameras
NETWORK
Interface
10Base-T/100Base-TX auto-negotiation, RJ-45 socket
Support MDI/MDI-X auto crossover function
Supported
Protocols
TCP/IP,IPV6,UDP,ICMP,DHCP,NTP,DNS,DDNS,SMTP,SNMP,FTP,HTTP,HTTPs,
PPPoE,UPnP,Bonjour,RTP,RTSP,RTCP,UDP,IGMP,ICMP,ARP,ONVIF,PSIA
TERMINAL I/O
Alarm Input/Output
1/1
Audio Input/Output
1/1
Test Video Output
BNC socket, composite 1 V p-p / 75Ω
IR LEDs
IR Distance
40 meters / 131feet
IR Wavelength
850nm
IR LED Lifespan
Up to 20,000 hours
EVENT MNGMNT
Event Trigger
Notification
Alarm Input, Manual Trigger, Motion Detection
Trigger alarm output, Send mail notification, Upload video to FTP, Record video to PC and
Network alarm
LOCAL STORAGE
Micro SD Card
Secure Disk physical layer specification version 2.0
Supports SDHC Host Specification
POWER
49
EZN-Series IP Cameras
Power Supply
DC 12V & PoE
Power over
Ethernet
Max. Power
Consumption
Yes (PoE 802.3af)
9W (IR LEDs on )
9W (IR LEDs on )
PHYSICAL
Operation
Temperature
-40°C ~ 55°C / -40°F ~ 131°F (DC 12V)
-20°C ~ 55°C / -4°F ~ 131°F ( PoE )
Humidity
20% ~ 80% non-condensing
Weight
Dimensions (L x W
x H)
1.62kg
359.9mm x 95.5mm x 95.5mm
Environm. Rating
IP66 for outdoor
Certificates
CE, FCC
50
8W (IR LEDs on )
EZN-Series IP Cameras
EverFocus Electronics Corp.
EverFocus Taiwan:
EverFocus Europe - Germany:
12F, No.79, Sec. 1, Shin-Tai Wu Road,
Albert-Einstein-Strasse 1, D-46446
Hsi-Chih, Taipei, Taiwan
Emmerich, Germany
TEL: +886 2 2698 2334
TEL: +49 2822 93940
FAX: +886 2 2698 2380
FAX: +49 2822 939495
www.everfocus.com.tw
www.everfocus.de
[email protected]
[email protected]
EverFocus China - Beijing:
EverFocus China - Shenzhen:
Room 609, Technology Trade Building,
4F, No. 2, D4 Building, Wan Yelong
Shangdi Information Industry Base,
Industrial Park, Tangtou Road, Shiyan,
Haidian District, Beijing 100085, China
Baoan, Shenzhen, Guangdong 518101, China
TEL: +86 10 6297 3336~39
TEL: +86 755 2765 1313
FAX: +86 10 6297 1423
FAX: +86 755 2765 0337
www.everfocus.com.cn
www.everfocus.com.cn
[email protected]
[email protected]
EverFocus USA - California:
EverFocus USA - New York:
1801 Highland Avenue, Unit A, Duarte, CA 91010, USA
415 Oser Avenue, Unit S, Hauppauge, NY 11788, USA
TEL: +1 626 844 8888
TEL: +1 631 436 5070
FAX: +1 626 844 8838
FAX: +1 631 436 5027
www.everfocus.com
www.everfocus.com
[email protected]
[email protected]
EverFocus Japan:
EverFocus Europe - UK:
5F, Kinshicho City Building, 2-13-4 Koto-Bashi,Sumida-Ku,
Unit 12, Spitfire Business Park,
Tokyo, 130-0022, Japan
Hawker Road, Croydon Surrey, CR0 4WD, UK
TEL: +81 3 5625 8188
TEL: +44 20 8649 9757 / +44 845 430 9999
FAX: +81 3 5625 8189
FAX: +44 20 8649 9907
www.everfocus.co.jp
www.everfocusuk.co.uk
[email protected]
[email protected]
EverFocus India:
Your EverFocus product is designed
and manufactured with high quality
materials and components which can
be recycled and reused.
This symbol means that electrical and
electronic equipment, at their
end-of-life, should be disposed of
separately from your household
waste.
Please, dispose of this equipment at
your local community waste
collection/recycling centre.
In the European Union there are
separate collection systems for used
electrical and electronic product.
Please, help us to conserve the
environment we live in!
Suite 803, Housefin Bhavan, C-21,
Bandra Kurla Complex, Bandra (East),
Mumbai 400051, India
TEL: +91 22 6128 8700
FAX: +91 22 6128 8705
www.everfocus.in
Ihr EverFocus Produkt wurde entwickelt
und hergestellt mit qualitativ
hochwertigen Materialien und
Komponenten, die recycelt und wieder
verwendet werden können.
Dieses Symbol bedeutet, dass
elektrische und elektronische Geräte am
Ende ihrer Nutzungsdauer vom
Hausmüll getrennt entsorgt werden
sollen.
Bitte entsorgen Sie dieses Gerät bei
Ihrer örtlichen kommunalen
Sammelstelle oder im Recycling Centre.
Helfen Sie uns bitte, die Umwelt zu
erhalten, in der wir leben!
[email protected]
P/N: 4605PZ3160B010A
51

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement