JVC SR-DVM70US User's Manual

JVC SR-DVM70US User's Manual
DVM70S_00.book Page 1 Friday, May 6, 2005 12:06 PM
DVD / HDD & Mini DV VIDEO RECORDER
SR-DVM70US
CABLE/DBS
TV
DVD
STANDBY/ON
TV/
DVD
VIDEO TV/CBL/DBS
DV
HDD
DVD
TV VOL
CH
CANCEL
LIVE
AUX
MEMO/MARK
DUBBING
EDIT
PROG
TV MUTING
TOP MENU
NAVIGATION
ENTER
RETURN
MENU
PREVIOUS
NEXT
SLOW
PLAY/SELECT
STOP/ CLEAR
REC
SLOW
NTSC
PAUSE
JUMP
REC MODE
DISPLAY
ON SCREEN
SET UP
VPS/PDC
SAT
SUBTITLE
ANGLE
PROGRESSIVE
SCAN
OPERATE
REMAIN
DISPLAY
AUDIO
EJECT
S-VIDEO
VIDEO (MONO)L - AUDIO - R
DV
CH
REC
HDD
REC
DVD
REC
EJECT
DV/HDD/DVD
STOP
REC MODE
REW
PLAY
INSTANT REPLAY
FF
PAUSE
AUDIO DUB.
REC
INSERT
DV IN/ OUT
IN F-1
LIVE CHECK
For Customer Use:
Enter below the Model No. and Serial
No. which are located on the rear of
cabinet. Retain this information for
future reference.
INSTRUCTIONS
Model No.
Serial No.
LPT1006-001B
EN
Filename [DVM70S_02Safety.fm]
Masterpage:Left0
DVM70S_00.book Page 2 Friday, May 6, 2005 12:06 PM
2
EN
SAFETY FIRST
Dear Customer,
Thank you for purchasing the JVC DVD / HDD & Mini DV video
recorder. Before use, please read the safety information and
precautions to ensure safe use of your new unit.
Cautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS
RISQUE DE CHOC ELECTRIQUE
- NE PAS OUVRIR.
CABLE COMPATIBLE TELEVISION APPARATUS
- TELEVISION CABLOCOMPATIBLE , CANADA
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the user
to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and maintenance
(servicing) instructions in the literature
accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
CAUTION:
This unit should be used with AC 120VH, 60Hz only.
To prevent electric shocks and fire hazards, DO NOT use any
other power source.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF
PLUG TO WIDE SLOT, FULLY INSERT.
ATTENTION:
POUR ÉVITER LES CHOCS ÉLECTRIQUES, INTRODUIRE
LA LAME LA PLUS LARGE DE LA FICHE DANS LA BORNE
CORRESPONDANTE DE LA PRISE ET POUSSER
JUSQU’AU FOND.
Note to CATV system installer:
This reminder is provided to call the CATV system installer’s
attention to Article 820-40 of the NEC that provides guidelines
for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the
building, as close to the point of cable entry as practical.
CAUTION:
Changes or modifications not approved by JVC could void user’s
authority to operate the equipment.
CAUTION:
A UNIT IS A CLASS 1 LASER PRODUCT. HOWEVER THIS
UNIT USES A VISIBLE LASER BEAM WHICH COULD CAUSE
HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE
SURE TO OPERATE THE UNIT CORRECTLY AS
INSTRUCTED.
WHEN THIS UNIT IS PLUGGED INTO THE WALL OUTLET,
DO NOT PLACE YOUR EYES CLOSE TO THE OPENING OF
THE DISC TRAY AND OTHER OPENINGS TO LOOK INTO
THE INSIDE OF THIS UNIT.
USE OF CONTROLS OR ADJUSTMENTS OR
PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF.
REFER SERVICING TO QUALIFIED PERSONNEL.
CLASS 1 LASER PRODUCT
REPRODUCTION OF LABELS
WARNING LABEL INSIDE OF THE UNIT
Page 2
Friday, 6 May 2005 12:06
Filename [DVM70S_02Safety.fm]
DVM70S_00.book Page 3 Friday, May 6, 2005 12:06 PM
Masterpage:Right+
SAFETY FIRST
IMPORTANT PRODUCT SAFETY
INSTRUCTIONS
Electrical energy can perform many useful functions. But improper
use can result in potential electrical shock or fire hazards. This
product has been engineered and manufactured to assure your
personal safety. In order not to defeat the built-in safeguards,
observe the following basic rules for its installation, use and
servicing.
EN
3
ANTENNA INSTALLATION INSTRUCTIONS
1. Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product,
be sure the antenna or cable system is grounded so as to provide
some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regard to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an
antenna discharge unit, size of grounding connectors, location of
antenna discharge unit, connection to grounding electrodes, and
requirements for the grounding electrode.
ATTENTION:
Follow and obey all warnings and instructions marked on your
product and its operating instructions. For your safety, please read
all the safety and operating instructions before you operate this
product and keep this booklet for future reference.
2. Lightning
For added protection for this product during a lightning storm, or
when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable
system. This will prevent damage to the product due to lightning
and power-line surges.
INSTALLATION
1. Grounding or Polarization
(A)Your product may be equipped with a polarized alternatingcurrent line plug (a plug having one blade wider than the other).
This plug will fit into the power outlet only one way. This is a
safety feature.
If you are unable to insert the plug fully into the outlet, try
reversing the plug. If the plug should still fail to fit, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the polarized plug.
(B)Your product may be equipped with a 3-wire grounding-type
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet, contact your
electrician to replace your obsolete outlet. Do not defeat the
safety purpose of the grounding-type plug.
2. Power Sources
Operate your product only from the type of power source indicated
on the marking label. If you are not sure of the type of power
supply to your home, consult your product dealer or local power
company. If your product is intended to operate from battery
power, or other sources, refer to the operating instructions.
3. Overloading
Do not overload wall outlets, extension cords, or integral
convenience receptacles as this can result in a risk of fire or
electric shock.
4. Power Cord Protection
Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them,
paying particular attention to cords at plugs, convenience
receptacles, and the point where they exit from the product.
5. Ventilation
Slots and openings in the cabinet are provided for ventilation. To
ensure reliable operation of the product and to protect it from
overheating, these openings must not be blocked or covered.
● Do not block the openings by placing the product on a bed, sofa,
rug or other similar surface.
● Do not place the product in a built-in installation such as a
bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
6. Wall or Ceiling Mounting
The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
3. Power Lines
An outside antenna system should not be located in the vicinity of
overhead power lines or other electric light or power circuits, or
where it can fall into such power lines or circuits. When installing
an outside antenna system, extreme care should be taken to keep
from touching such power lines or circuits as contact with them
might be fatal.
Page 3
Friday, 6 May 2005 12:06
Filename [DVM70S_02Safety.fm]
DVM70S_00.book Page 4 Friday, May 6, 2005 12:06 PM
4
EN
Masterpage:Left+
SAFETY FIRST
USE
1. Accessories
To avoid personal injury:
● Do not place this product on an unstable cart, stand, tripod,
bracket, or table. It may fall, causing serious injury to a child or
adult, and serious damage to the product.
● Use only with a cart, stand, tripod, bracket, or table
recommended by the manufacturer or sold with the product.
● Use a mounting accessory recommended by the manufacturer
and follow the manufacturer’s instructions for any mounting of
the product.
● Do not try to roll a cart with small casters across thresholds or
deep-pile carpets.
2. Product and Cart Combination
A product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.
3. Water and Moisture
Do not use this product near water—for
example, near a bath tub, wash bowl,
kitchen sink or laundry tub, in a wet
basement, or near a swimming pool and the like.
4. Object and Liquid Entry
Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or shortout parts that could result in a fire or electric shock. Never spill
liquid of any kind on the product.
5. Attachments
Do not use attachments not recommended by the manufacturer
of this product as they may cause hazards.
6. Cleaning
Unplug this product from the wall outlet before cleaning. Do not
use liquid cleaners or aerosol cleaners. Use a damp cloth for
cleaning.
7. Heat
The product should be situated away from heat sources such
as radiators, heat registers, stoves, or other products (including
amplifiers) that produce heat.
SERVICING
1. Servicing
If your product is not operating correctly or exhibits a marked
change in performance and you are unable to restore normal
operation by following the detailed procedure in its operating
instructions, do not attempt to service it yourself as opening or
removing covers may expose you to dangerous voltage or other
hazards. Refer all servicing to qualified service personnel.
2. Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to
qualified service personnel under the following conditions:
a. When the power supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the product.
c. If the product has been exposed to rain or water.
d. If the product does not operate normally by following the
operating instructions. Adjust only those controls that are
covered by the operating instructions as an improper
adjustment of other controls may result in damage and will
often require extensive work by a qualified technician to restore
the product to its normal operation.
e. If the product has been dropped or damaged in any way.
f. When the product exhibits a distinct change in performance—
this indicates a need for service.
3. Replacement Parts
When replacement parts are required, be sure the service
technician has used replacement parts specified by the
manufacturer or which have the same characteristics as the
original part. Unauthorized substitutions may result in fire,
electric shock or other hazards.
4. Safety Check
Upon completion of any service or repairs to this product, ask
the service technician to perform safety checks to determine
that the product is in safe operating condition.
HOW TO USE THIS INSTRUCTION MANUAL
● All major sections and subsections are listed in the Table Of
Contents on page 6. Use this when searching for information on
a specific procedure or feature.
● The Index on pages 12 - 15 illustrates the controls and
connections on the front and rear panel, the front display panel
and the remote control.
● The list of terms on page 89 lists frequently-used terms, and the
number of the page on which they are used or explained in the
manual.
● The A mark signals a reference to another page for instructions
or related information.
● Operation buttons necessary for the various procedures are
clearly indicated through the use of illustrations at the beginning
of each major section.
BEFORE YOU INSTALL YOUR NEW UNIT . . .
. . . please read the sections/literature listed below.
● ACautionsB on page 2
● AIMPORTANT PRODUCT SAFETY INSTRUCTIONSB on
pages 3 - 5
Page 4
Friday, 6 May 2005 12:06
Filename [DVM70S_02Safety.fm]
DVM70S_00.book Page 5 Friday, May 6, 2005 12:06 PM
Masterpage:Right+
SAFETY FIRST
Declaration of Conformity
Model Number:
SR-DVM70US
Trade Name:
JVC
Responsible Party: JVC Americas Corp.
Address:
1700 Valley Road Wayne, N.J. 07470
Telephone Number: 973-317-5000
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
NTSC
● Manufactured under license from Dolby Laboratories. ADolbyB
and double-D symbol are trademarks of Dolby Laboratories.
● ADTSB and ADTS DIGITAL OUTB are trademarks of Digital
Theater Systems, Inc.
P can be used with the DV deck of this
unit. The DV deck can play back and record only NTSC signals.
● VCR Plus+ and PlusCode are registered trademarks of Gemstar
Development Corporation.
The VCR Plus+ system is manufactured under license from
Gemstar Development Corporation.
● DSS is an official trademark of DIRECTV, Inc., a unit of GM
Hughes Electronics. DISH Network is a trademark of Echostar
Communications Corporation.
● This product incorporates copyright protection technology that is
protected by method claims of certain U.S. patents and other
intellectual property rights owned by Macrovision Corporation
and other rights owners. Use of this copyright protection
technology must be authorized by Macrovision Corporation, and
is intended for home and other limited viewing users only unless
otherwise authorized by Macrovision Corporation. Reverse
engineering or disassembly is prohibited.
● Cassettes marked
TM
EN
5
When the equipment is installed in a cabinet or a shelf, make sure
that it has sufficient space on all sides to allow for ventilation
(10 cm or more on both sides, on top and at the rear).
When discarding batteries, environmental problems must be
considered and the local rules or laws governing the disposal of
these batteries must be followed strictly.
Failure to heed the following precautions may result in
damage to the unit, remote control or disc/cassette.
1. DO NOT place the unit ^
^ in an environment prone to extreme temperatures or
humidity.
^ in direct sunlight.
^ in a dusty environment.
^ in an environment where strong magnetic fields are
generated.
^ on a surface that is unstable or subject to vibration.
2. DO NOT block the unit’s ventilation openings or holes.
(If the ventilation openings or holes are blocked by a
newspaper or cloth, etc., the heat may not be able to get out.)
3. DO NOT place heavy objects on the unit or remote control.
4. DO NOT place anything which might spill on top of the unit
or remote control.
(If water or liquid is allowed to enter this equipment, fire or
electric shock may be caused.)
5. DO NOT expose the apparatus to dripping or splashing.
6. DO NOT use this equipment in a bathroom or places with
water. Also DO NOT place any containers filled with water or
liquids (such as cosmetics or medicines, flower vases, potted
plants, cups, etc.) on top of this unit.
7. DO NOT place any naked flame sources, such as lighted
candles, on the apparatus.
8. AVOID violent shocks to the unit during transport.
MOISTURE CONDENSATION
Moisture in the air will condense on the unit when you move it from
a cold place to a warm place, or under extremely humid
conditions^just as water droplets form on the surface of a glass
filled with cold liquid. In conditions where condensation may occur,
disconnect the unit’s power plug from the wall and keep it
disconnected for a few hours to let the moisture dry, then turn on
the unit.
DISCLAIMER OF LIABILITY
JVC shall not be liable for any loss relating to the unit’s failure to
properly record, store or playback any content (video, audio or
otherwise) for any reason whatsoever. Any applicable warranties
shall only cover replacement or repair of the effected unit, and
shall not apply to recovery or replacement of lost content.
TM
Page 5
ATTENTION:
8 Using a mobile phone in the vicinity of the unit may cause
picture vibration on the TV screen or change the screen to a
blue back display.
8 Some TVs or other appliances generate strong magnetic
fields. Do not place such appliances on top of the unit as it
may cause picture disturbance.
8 When moving the product, press A to turn off the power,
and wait at least 30 seconds before unplugging the power
cord. Then, wait at least 2 minutes before moving the
product.
8 If there is a power outage when using the unit, the recorded
data may be erased.
8 It is recommended to back up discs which contain important
recordings periodically (every few years). As digital signals
do not deteriorate, failure to play back or record might arise
due to the effects of the disc aging through the years
depending on the storage environment.
8 Recorded programs and data cannot be restored once the
disc is damaged.
Friday, 6 May 2005 12:06
Filename [DVM70S_03TOC.fm]
Masterpage:Left0
DVM70S_00.book Page 6 Friday, May 6, 2005 12:06 PM
6
EN
CONTENTS
SAFETY FIRST
DISC INFORMATION
2
7
About Discs ....................................................................................7
INDEX
12
INSTALLING YOUR NEW UNIT
18
Basic Connections .......................................................................18
INITIAL SETTINGS
19
Plug & Play Set ............................................................................19
Language .....................................................................................20
Clock Set......................................................................................21
Tuner Set .....................................................................................22
Monitor Set...................................................................................23
BASIC OPERATIONS ON DVD DECK
24
Basic Playback.............................................................................24
Playback Features .......................................................................25
Using The On-screen Bar ............................................................29
Parental Lock ...............................................................................33
Basic Recording ...........................................................................34
Recording Features......................................................................35
BASIC OPERATIONS ON HDD DECK
37
Basic Recording ...........................................................................37
Recording Features......................................................................38
Basic Playback.............................................................................39
Playback Features .......................................................................39
BASIC OPERATIONS ON DV DECK
41
NAVIGATION ON HDD/DVD DECK
50
Library Database Navigation ....................................................... 50
Edit Original Information .............................................................. 51
Edit Play List Information............................................................. 53
Edit Library Information ............................................................... 55
Playback With MP3/WMA/JPEG Navigation ............................... 56
EDITING
57
Dubbing ....................................................................................... 57
DV Dubbing (HDD & DVD Deck Only) ........................................ 60
Edit From A Camcorder ............................................................... 62
Edit To Or From Another Recorder ............................................. 63
Digital Audio Dubbing .................................................................. 64
Audio Dubbing (DV Deck Only) ................................................... 65
Insert Editing (DV Deck Only)...................................................... 66
REMOTE CONTROL
67
Remote Control Functions ........................................................... 67
SYSTEM CONNECTIONS
69
Connecting To A Dolby Digital Decoder Or An Amplifier
With Built-in DTS....................................................................... 69
SUBSIDIARY SETTINGS
70
Mode Set ..................................................................................... 70
Changing VCR Plus+ Setting ...................................................... 73
Format A Disc (DVD Deck Only) ................................................. 74
Finalize A Disc (DVD Deck Only) ................................................ 75
Scan Mode Set (HDD & DVD Deck Only) ................................... 76
Tray Lock (DVD Deck Only) ........................................................ 76
Mode Lock ................................................................................... 76
Last Function Memory ................................................................. 76
Basic Playback.............................................................................41
Playback Features .......................................................................42
TROUBLESHOOTING
77
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
APPENDIX
81
RS-232C INTERFACE
84
43
Live Memory Playback .................................................................43
TIMER RECORDING ON HDD/DVD DECK
46
VCR Plus+ Timer Programming...................................................46
Manual Timer Programming.........................................................48
Page 6
RS-232C Interface – Command Table – ..................................... 84
RS-232C Interface – Specifications –.......................................... 84
RS-232C Interface – Command – ............................................... 85
SPECIFICATIONS
88
LIST OF TERMS
89
May 6, 2005 12:06 pm
Filename [DVM70S_04DiscInfo.fm]
DVM70S_00.book Page 7 Friday, May 6, 2005 12:06 PM
Masterpage:Right0
DISC INFORMATION
About Discs
Recordable/Playable Discs
You can use discs with the following logos for recording and
playback.
DVD-RAM
DVD-RW
12 cm: 4.7 GB/9.4 GB
8 cm: 1.4 GB/2.8 GB
Ver. 2.0/2x speed
Ver. 2.1/1x – 3x speed
Ver. 2.2/5x speed
12 cm: 4.7 GB/9.4 GB
Ver. 1.1/1x – 2x speed
(Video mode/VR mode)
Ver. 1.2/4x speed
(Video mode/VR mode)
DVD-R
12 cm: 4.7 GB
8 cm: 1.4 GB
Ver. 2.0/1x – 4x/8x speed
(Video mode)
● The above table is based on the information as of October 2004.
● Recording and playback may not be performed depending on the
characteristics and condition of the disc used, leading to
unsatisfactory results. Using discs manufactured by JVC is
recommended since they have been tested to be compatible with
this unit.
DVD-RAM Discs
It is only possible to use discs which conform with DVD-RAM
standard Version 2.0 or 2.1.
● It is impossible to record on DVD-RAM discs which do not
conform to this standard. If you use a disc formatted under a
different standard version, format it on this unit before use.
● It may not be possible to record, play back, edit or dub a
DVD-RAM disc even if it conforms to the standard if it was
recorded or edited on the devices from other manufacturers or on
a PC, or if it has far too many titles, or if there is very little
available capacity remaining on the disc.
● DVD-RAM discs recorded on this unit cannot be played back on
an incompatible DVD player.
● It is possible to record copy-once programs of digital broadcasts
only onto 4.7/9.4 GB DVD-RAM discs (2.8 GB DVD-RAM discs
are not compatible).
Page 7Friday, 6 May 2005 12:06
EN
7
DVD-R/RW Discs
It is only possible to use DVD-R discs which conform with DVD-R
standard Version 2.0.
When a DVD-R/RW disc (Video mode) is finalized (A pg. 75), it
can be played back on a standard DVD player as a DVD VIDEO
disc.
When a DVD-RW disc (VR mode) is finalized (A pg. 75), it can be
played back on a standard DVD player compatible with the VR
mode of DVD-RW discs.
Before finalizing ^
^ it is possible to record on unrecorded areas of the disc, edit the
disc title and program titles, and delete programs.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
program is deleted from a DVD-R disc.
After finalizing ^
After a DVD-R/RW disc (Video mode) has been finalized, it is
possible to play back the recorded programs (video and/or audio)
on a standard DVD video player as a DVD VIDEO disc.
● Edited titles are displayed as the
ADVD menuB in video mode.
● It is impossible to record, edit or
delete the data either in video
mode or in VR mode.
● Either in video mode or in VR
mode, although the disc can be
played back on DVD players from
other manufacturers, sometimes it
may not be possible to play back depending on the disc and
recording conditions.
● It is impossible to record on CD-R/RW or DVD-R discs used for
authoring.
● It is impossible to record onto DVD-R/RW (Video mode) discs
broadcasts that allow you to copy once. The copy once programs
can only be recorded onto DVD-RW discs formatted in VR mode.
HOME MOVIES
DOCUMENTARIES
MTV
CARTOON
TRAVELLING CLIPS
NOTE:
The following may result if you play back a DVD-R disc recorded
on another unit.
● The disc does not play.
● A mosaic pattern (block noise) appears on the screen.
● Video or audio may be dropped out.
● The unit stops during playback.
Filename [DVM70S_04DiscInfo.fm]
DVM70S_00.book Page 8 Friday, May 6, 2005 12:06 PM
8 EN DISC INFORMATION
Discs For Playback Only
Unplayable Discs
You can use discs with the following logos for playback only.
DVD VIDEO
Video CD/Super Video CD
(example of region code
indications)
Audio CD
CD-DA files
CD-R
CD-DA/JPEG/
MP3 files
CD-RW
CD-ROM
JPEG/MP3 files
CD-DA/JPEG/
MP3 files
● Playback may not be performed depending on the characteristics
and condition of the disc used.
● DTS Audio CDs can also be played back (An optional DTS
decoder is required).
● MP3 and JPEG discs can be played back on this unit only when
they have been recorded in the ISO9660 or Joliet format and
finalized.
● JPEG files that can be played back on this unit must conform to
JFIF/Baseline process, and the maximum resolution of a JPEG
file is 2,812 pixels in width and 2,112 pixels in height.
● CD-R/RW discs recorded in music CD format need to be finalized
to play back on this unit.
● Operation and audio quality of this unit are not guaranteed for
discs that do not conform to the Compact Disc specification
(CD-DA).
Before you play back a CD, check for the CD logo and read the
notes on the package to confirm that it conforms to the Compact
Disc specification.
● Depending on the intentions of the author of the software,
recording conditions of DVD discs and Video CD/SVCD discs
may be restricted. Since this unit plays back discs according to
the intentions of the author of the software as indicated on the
disc, some functions may not operate as commanded.
● When switching from the first layer to the second layer of doublelayered DVD VIDEO discs, the image and sound may be
momentarily distorted. This is not a malfunction.
● DVD-AUDIO discs compatible with DVD video players can be
played.
● Super Audio CDs (SACD) compatible with conventional CD
players can be played.
Page 8Friday, 6 May 2005 12:06
Masterpage:Left+
The following types of discs cannot be played using this unit.
Do not attempt to play back any kind of disc that is damaged
(cracked, warped, or repaired with adhesive tape) or discs in
unusual shapes (heart-shaped, octagonal, or other forms). If such
discs are accidentally played back, it may cause noise that can
lead to speaker damage.
● CD-ROM discs (including PHOTO-CD and CD-G)
● Discs recorded in Packet Write (UDF) format
● 1.3-GB double density CDs (DDCD)
● High density CDs (HDCD)
The following discs also cannot be played back.
● Discs of a region number other than A1B
● DVD-RAM (2.6 GB/5.2 GB)
● DVD-RAM (TYPE1)
Caution for DualDisc playback
The Non-DVD side of a ADualDiscB does not comply with the
ACompact Disc Digital AudioB standard. Therefore, the use of NonDVD side of a DualDisc on this product may not be recommended.
Region Number
The world is divided into 6 regions for DVD VIDEO discs.
DVD VIDEO discs are assigned a region number to indicate which
region they may be played back in. A disc cannot be played back
on this unit unless the region number of the disc matches that of
the unit. The region number for this unit is A2B. Only discs whose
region number includes A2B or AALLB can be played back such as
shown below.
Examples of DVD VIDEO labels which can be played back
using this unit.
Marks of discs in this instruction manual
Allows operation with a
DVD-RAM disc.
Allows operation with a
Video CD/Super Video
CD (SVCD) disc.
Allows operation with a
DVD-R disc.
Allows operation with
an Audio CD disc.
Allows operation with a
DVD-RW disc.
Allows operation with a
disc including MP3
files.
Allows operation with a
DVD VIDEO disc.
Allows operation with a
disc including JPEG
files.
Filename [DVM70S_04DiscInfo.fm]
Masterpage:Right+
DVM70S_00.book Page 9 Friday, May 6, 2005 12:06 PM
DISC INFORMATION
Recording Medium And Format
DVD-RAM
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
● While recording, it is possible not only to start playback of a
program currently being recorded, but also to watch another
program previously recorded.
DVD-RW (VR mode)
● Recording and erasing can be performed as many times as
possible on a disc.
● Editing can be performed after recording, such as deleting
unwanted parts.
DVD-RW (Video mode)
● Can be played back on other DVD players.
● New recording can be performed by erasing all the data on a disc
once played back.
EN
9
Audio CD/Video CD/SVCD
Typically, Audio CD discs are divided into separate tracks each
containing one song. Each track is assigned a number. For
example, the third track is Track 3. The same is true for Video CD/
SVCD discs.
However, some discs are not divided into tracks.
Audio CD or Video CD/SVCD
Track 1
Track 2
Track 3
Track 4
JPEG/MP3 Disc (CD-R/RW/ROM)
MP3/JPEG files put in directories nested in several levels on a disc
will be organized as if they were put in single level directories
(groups) by the MP3/JPEG Navigation of this unit. (A pg. 56)
File structure of a disc before starting the MP3/JPEG
Navigation
DVD-R
● Can be played back on other DVD players.
● Suitable when keeping a recorded disc for a long time.
File Structure Of Discs
DVD VIDEO
Typically, DVD VIDEO discs are made up of larger units called
AtitlesB. Each title has a number (title number) that can be used to
select desired titles. Titles are further divided into units called
AchaptersB. Each chapter has a number (chapter number) that can
also be used to select desired chapters. Note that some discs are
not divided into titles and chapters.
When you record a program on a DVD-RAM/RW (VR mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes from monaural to stereo
due to commercial breaks, etc. It is also possible to insert chapter
marks at desired locations during playback. (A pg. 27)
Directory
MP3 file
JPEG file
File structure of the disc after starting the MP3/JPEG
Navigation
Files are automatically grouped as follows and displayed on the
MP3/JPEG Navigation screen. Data is displayed in the
alphabetical order of file name. Files are grouped based on roots.
When you record a program on a DVD-R/RW (Video mode)
disc
A single recording session results in a single title (a single
chapter). However, chapter marks are automatically inserted when
recording is paused, or audio changes due to commercial breaks,
etc. It is also possible to insert chapter marks at desired locations
during either recording or playback. Once the disc has been
finalized, these chapter marks are deleted and new chapter marks
are assigned automatically approximately every 5 minutes.
DVD-RAM, DVD-RW, DVD-R or DVD VIDEO disc
Title 1
Chapter 1
Chapter 2
● This unit can recognize up to 9 hierarchies including directories
Title 2
Chapter 3
Chapter 1
Chapter 2
Chapter 3
● In Video mode, even before finalizing, it is impossible to perform
editing operations other than changing the disc name and/or title
names and deleting programs and/or titles.
● After finalizing, it is impossible to perform editing operations.
Page 9Friday, 6 May 2005 12:06
and files.
Also, it can recognize up to 250 files in each group, and up to 99
groups on a disc.
NOTES:
● Video CD/SVCD discs that support Playback Control (PBC)
The contents of a disc are recorded into several hierarchies, and
played back according to the instructions on the screen while
navigating through the hierarchies. It is also possible to playback
recorded tracks consecutively without activating the PBC function
even when playing a PBC-compatible disc. (A pg. 28)
● Regarding the contents recorded on discs
Some files may not be played back depending on the file types
and other factors.
Filename [DVM70S_04DiscInfo.fm]
DVM70S_00.book Page 10 Friday, May 6, 2005 12:06 PM
10 EN DISC INFORMATION
DVD VIDEO Marks
Masterpage:Left+
Placing A Disc
Sometimes marks are printed on a DVD disc and/or on its
packaging to indicate information regarding the contents and
functions of the disc. Check the marks indicating the contents and
functions of the disc. Note, however, that in some cases a disc
may not include a mark even for a function it supports.
Opening the disc tray
Press M to open the disc tray.
Marks related to video
Number of subtitles
Number of angles
DVD
Recorded under the
standard 4:3 aspect
ratio
Screen includes black
bands at the top and
the bottom of image
which has a standard
4:3 aspect ratio (letter
box)
Video playback is in Wide video mode (16:9) on
wide televisions, but in letter box on televisions
with standard 4:3 aspect ratio.
Video playback is in Wide video mode (16:9) on
wide televisions, but pan and scan is used on
televisions with standard 4:3 aspect ratio (either
the left or right side of the image is cut-out).
EJECT
REC
DV/HDD/DVD
REC MODE
STOP
REW
PLAY
INSTANT REPLAY
FF
PAUSE
AUDIO DUB.
REC
INSERT
DV IN/ OUT
● Pressing the button again closes the disc tray.
● Use the button to open and close the disc tray.
● Do not block the disc tray with your hand while it is opening or
closing as this may result in hardware failure.
● Do not place unplayable discs or any object other than a disc on
the disc tray.
● Do not press down strongly on the disc tray or place any heavy
objects on it.
Discs without cartridges
Marks related to audio
Number of audio tracks
DUBBIN
DVD
G
VCR
TIMER
DVD
REC
PULL-OP
REC
PLAY
SE
REMAIN
REC
PAUSE
REW
<< SLOW
REC
Dolby Digital mark
It has been developed by Dolby Laboratories as
a digital surround system.
DTS (Digital Theater Systems)
You can enjoy DTS audio if you connect an
amplifier with a built-in DTS decoder to the
DIGITAL OUT connector of the unit.
LINK
EN
DV IN
CH
STOP
PEN/CLO
FF
DVD
>>
MODE
Disc tray
Place the disc on the disc tray with the label side facing up. Since
disc size changes depending on the disc to be played back, be
sure to correctly align the disc with the grooves for its size. If the
disc is not in its groove, it may be scratched or otherwise
damaged. To insert an 8 cm disc, place it according to the inner
groove.
DVD-RAM discs contained in cartridges
Double-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the side
you wish to play back or record facing down. If you insert the disc
with ASide AB facing down, programs are recorded on the side A.
Single-sided discs:
Remove the disc from the cartridge. Align the disc with the grooves
on the disc tray as shown in the illustration and insert with the label
side facing up.
Page 10Friday, 6 May 2005 12:06
Filename [DVM70S_04DiscInfo.fm]
DVM70S_00.book Page 11 Friday, May 6, 2005 12:06 PM
Masterpage:Right+
DISC INFORMATION
Care And Handling Of Discs
How to handle discs
When handling a disc, do not
touch the surface of the disc.
Since discs are made of
plastic, they are easily
damaged. If a disc gets dirty,
dusty, scratched or warped, the
images and sound will not be
picked up correctly, and such a
disc may cause the unit to malfunction.
Label side
Do not damage the label side, stick paper to or use any adhesives
on its surface.
Recording side
Make sure that discs are not scratched or dirty on the recording
side before use. Scratches and dirt on the recording side of a disc
may hinder proper playback and recording. Also be careful that a
DVD-RAM disc may get scratched or dirty when removed from
cartridge then put back in after use.
Storage
Make sure that discs are kept in their cases. If discs are piled on
top of one another without their protective cases, they can be
damaged. Do not put discs in a location where they may be
exposed to direct sunlight, or in a place where the humidity or
temperature is high. Avoid leaving discs in your car!
Maintenance of discs
If there are fingerprints or other dirt adhering
to a disc, wipe with a soft dry cloth, moving
from the centre outwards.
If a disc is difficult to clean, wipe with a cloth
moistened with water. Never use record
cleaners, petrol, alcohol or any anti-static
agents.
CAUTION:
Sometimes during playback, noise may appear or images may
be garbled. This is sometimes due to the disc. (It may not be up
to industry standards.)
These symptoms are caused by the discs, not by the
malfunction of the unit.
Page 11Friday, 6 May 2005 12:06
EN
11
Filename [DVM70S_05Name.fm]
Masterpage:Left0
DVM70S_00.book Page 12 Friday, May 6, 2005 12:06 PM
12 EN INDEX
Front View
J
A
C
B
D
E
F
G
H
EJECT
DV/HDD/DVD
K L M
I
OPERATE
DISPLAY
EJECT
S-VIDEO
DV
VIDEO (MONO)L - AUDIO - R
−
REC
HDD
REC
DVD
REC
STOP
CH +
REC MODE
REW
PLAY
INSTANT REPLAY
FF
PAUSE
AUDIO DUB.
REC
INSERT
DV IN/ OUT
IN F-1
N
O
A
B
C
D
P
Q
R
OPERATE Button (A)
Eject Button (EJECT M) (DV) A pg. 41
Mini DV Cassette Loading Slot
DV Lamp (DV) A pg. 41
DV Recording Lamp (REC)
E HDD Lamp (HDD) A pg. 20, 37
HDD Recording Lamp (REC) A pg. 37
F DVD Lamp (DVD) A pg. 20, 24
DVD Recording Lamp (REC) A pg. 34
G Open/Close Button (EJECT M) (DVD) A pg. 10
H DV/HDD/DVD Select Button (DV/HDD/DVD) A pg. 24, 37, 41
● This button will not function during navigation mode or set up
mode.
I Recording Mode Button (REC MODE) A pg. 34, 37
J Instant Replay Button (INSTANT REPLAY) A pg. 28, 40, 42
K Disc Tray
L Audio Dubbing Button (AUDIO DUB.) A pg. 65
M Insert Button (INSERT) A pg. 66
S
T U VWX Y
Z
N Display Button (DISPLAY) A pg. 27, 35
O S-video Input Connector [S-VIDEO] A pg. 62
P Video/Audio Input Connectors
[VIDEO/AUDIO ((MONO) L/R)] A pg. 62
Q Channel Buttons (CH +/- JK) A pg. 34, 37
R Front Display Panel A pg. 14
S Infrared Beam Receiving Window
T Stop Button (STOP o) A pg. 24, 39
U Reverse Search Button (O) (HDD & DVD deck) A pg. 25,
44
Rewind Button (REW O) (DV deck) A pg. 41, 42
V Play Button (PLAY I) A pg. 24, 39
W Forward Search Button (N) (HDD & DVD deck) A pg. 25,
44
Fast Forward Button (FF N) (DV deck) A pg. 41, 42
X Pause Button (PAUSE W) A pg. 24, 39
Y Record Button (REC R) A pg. 34, 37
Z DV Input/Output Connector [DV IN/OUT(A*)] A pg. 60
* A (i.Link) refers to the IEEE1394-1995 industry specification and
extensions thereof. The A logo is used for products compliant with the
i.Link standard.
Page 12
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right+
DVM70S_00.book Page 13 Friday, May 6, 2005 12:06 PM
INDEX
EN
13
Rear View
A
B
C
D
E
F
S VIDEO
G
I
H
S VIDEO
VHF/UHF
S VIDEO
Y
PB
IN
SERIAL COM.
HDD/DVD
PCM/
STREAM
DIGITAL
AUDIO OUT
DV/HDD/DVD
OUTPUT
AUDIO
PR
R
VIDEO
COMPONENT
VIDEO OUT
COAXIAL
OPTICAL
J
A Region Number A pg. 8
B AC Power Cord A pg. 18
C Cooling Fan
● This prevents the temperature from rising inside the unit.
Do not remove it.
● Install the unit so as not to block the area around the fan.
● The unit may become hot when it is turned off, as the cooling
fan on the rear of the unit is not activated. However, the cooling
fan may be activated in the following cases;
^ When AAUTO CLOCKB is set to AONB (A pg. 21).
(Set AAUTO CLOCKB to AOFFB if you mind the noise of the
fan.)
D Component Video Output Connectors [COMPONENT
VIDEO OUT (Y/PB/PR)] (HDD & DVD deck only) A pg. 18
E Serial Command Connector (D-SUB 9-PIN) [SERIAL COM.]
A pg. 84
● Use this connector when controlling this unit via a computer.
The cable to be used should be a RS-232C interface cable
(straight type). For details on the RS-232C interface command,
refer to page 86.
Page 13
VIDEO
L
K
OUTPUT
HDD/DVD
VIDEO
VIDEO
L
AUDIO
R
L
AUDIO
REMOTE IN
OUT
R
INPUT L-1 OUTPUT
DV/HDD/DVD
L
M
F S-video/Video/Audio Output Connectors [S-VIDEO/VIDEO/
AUDIO OUTPUT] (HDD & DVD deck only) A pg. 18
G S-video/Video/Audio Input Connectors [S-VIDEO/VIDEO/
AUDIO INPUT (L-1)] A pg. 62
H S-video/Video/Audio Output Connectors [S-VIDEO/VIDEO/
AUDIO OUTPUT] A pg. 18
I Antenna Input Connector [VHF/UHF IN] A pg. 18
J Digital Audio Output Connectors
[DIGITAL AUDIO OUT (OPTICAL/COAXIAL)] (HDD & DVD
deck only) A pg. 64, 69
K BNC Video Output Connector [VIDEO OUTPUT] A pg. 18
L Remote Input Connector* [REMOTE IN]
* There is currently no compatible remote control unit available.
M Antenna Output Connector [VHF/UHF OUT] A pg. 18
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Left+
DVM70S_00.book Page 14 Friday, May 6, 2005 12:06 PM
14 EN INDEX
Front Display Panel
A
B
C
D
E
F
G
H
J
I
LPCM
FR
XP SP LP EP
VR -RW VCD
-RAM
K
L
A Disc Type Indicator
When a disc is loaded, the type of the disc is indicated.
Disc Status Indicator
When a disc is running, the disc marks rotate.
During High-Speed Search:
Rotate faster than normal playback.
During Slow Motion:
Rotate slower than normal playback.
While recording:
Inner red ring lights in the same way as normal playback.
During Instant Timer Recording (ITR), inner red ring slowly
blinks.
While paused:
Disc marks blink when either recording or playing back.
While stopped:
Disc marks all light.
While resume stopped:
Disc marks all blink.
While the disc tray opened: Disc marks all light out.
No disc on the disc tray:
Disc marks all light out.
VR Mode Indicator (VR) A pg. 74
Lights when a DVD-RW disc is formatted in VR mode.
B Linear PCM Indicator (LPCM)
Lights when AXP MODE REC AUDIOB is set to ALINEAR PCMB
(A pg. 71) for recording with HDD, DVD-RAM, DVD-R and
DVD-RW discs, and when Linear PCM audio is played.
C Cassette Loaded Mark (u)
Indicates the present of a cassette in the DV deck.
Lights when a cassette is loaded into the DV deck. It will remain
lit as long as the cassette is loaded, even if the HDD or DVD
deck is being selected.
D Recording Mode Indicator (XP/SP/LP/EP/FR) A pg. 34
Blinks when recording mode is being set.
While AFRB is blinking, the left 3 digits of the Multi Display (L
N) indicate setting values ranging from A60B to A480B. After the
value has been set, only AFRB lights.
E Group/Title Indicator (GRP/TITLE)
AGRPB or ATITLEB lights depending on a disc loaded while the
left 2 digits of the Multi Display (L) indicate the numbers
explained below.
AGRPB: Total number of groups or group number being played
back are displayed on the Multi Display.
ATITLEB: Total number of titles or title number being played
back are displayed on the Multi Display.
F Channel Indicator
Indicates the channel received.
Page 14
M
N
O
P
Q
G Track/Chapter Indicator (TRK/CHAP)
ATRKB or ACHAPB lights depending on a disc loaded while the
3rd and 4th digits from the left of the Multi Display (N) indicate
the numbers explained below.
ATRKB: Total number of tracks or track number being played
back are displayed on the Multi Display.
ACHAPB: Chapter number being played back are displayed on
the Multi Display.
H Simulated Surround Effect Indicator (3D) A pg. 31
Lights when a simulated surround effect is set to A3D-ONB on
the on-screen bar.
I Random/Program Playback Mode Indicator (RND/PRGM)
A pg. 32
ARNDB: Lights when Random Playback mode is set.
APRGMB: Lights when Program Playback mode is set.
J Repeat Mode Indicator (x/1/A-B) A pg. 29
Select Repeat Playback mode on the on-screen bar.
AxB:
Whole disc is played back repeatedly.
Ax1B:
A single title/chapter/track is played back
repeatedly.
AxA-BB: The selected part (A-B) is played back repeatedly.
No display: Repeat Playback mode is off.
K Video Output Indicator (q) A pg. 76
No display: Indicates that interlace mode is engaged.
q:
Indicates that progressive mode is engaged.
(Example) q lights when video output mode is in progressive
mode.
L Group/Title Number Display
M Audio Dubbing/Insert Editing Indicator
AADUBB or AINSB lights up during Audio Dubbing or Insert
Editing respectively.
N Track/Chapter Number Display
O Remaining Time/Elapsed Time Indicator A pg. 27, 35
Lights when remaining time of HDD, DVD-RAM, DVD-R and
DVD-RW discs is displayed, and lights out when elapsed time
is displayed.
The right 6 digits of the Multi Display (P) indicate elapsed or
remaining time of each track.
No display: Indicates elapsed time of the disc.
Displayed: Indicates remaining time of the disc.
P Remaining Time/Elapsed Time Display A pg. 27, 35
Time Code Display A pg. 42
Q Multi Display
Displays clock, received channel, elapsed time, and remaining
time.
Also displays status of the unit (NO DISC/OPEN/CLOSE/
READING).
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right+
DVM70S_00.book Page 15 Friday, May 6, 2005 12:06 PM
INDEX
Remote Control
CABLE/DBS
TV
A
DVD
STANDBY/ON
TV/
DVD
VIDEO TV/CBL/DBS
B
C
DV
HDD
DVD
TV VOL
T
U
V
W
X
D
CH
E
F
G
H
I
J
CANCEL
AUX
MEMO/MARK
LIVE
DUBBING
EDIT
M
TOP MENU
MENU
RETURN
PREVIOUS
NEXT
SLOW
PLAY/SELECT
REC
STOP/ CLEAR
SLOW
PAUSE
JUMP
O
R
NAVIGATION
ENTER
N
P
Q
PROG
TV MUTING
K
L
Y
REC MODE
DISPLAY
ON SCREEN
SET UP
REMAIN
AUDIO
S
SUBTITLE
ANGLE
LIVE CHECK
PROGRESSIVE
SCAN
Z
a
b
c
d
e
f
g
h
i
j
k
l
m
n
o
p
EN
15
Display Button (DISPLAY) A pg. 27, 35, 42
Audio Button (AUDIO) A pg. 28
Subtitle Button (SUBTITLE) A pg. 28
TV/CABLE/DBS/DVD switch A pg. 20
DVD STANDBY/ON Button (DVD A)
TV/CBL/DBS STANDBY/ON Button (TV/CBL/DBS A)
A pg. 67
W DVD Button* A pg. 24
Q
R
S
T
U
V
* This button will not function during navigation mode or set up mode.
X TV Volume Buttons (TV VOL +/–) A pg. 67
Y Channel Buttons (CH +/-) A pg. 34, 67
Z Memo Button (MEMO) A pg. 51, 54
Mark Button (MARK) A pg. 27
a Programming Button (PROG) A pg. 46, 48, 49
b Edit Button (EDIT) A pg. 51
c Navigation Button (NAVIGATION) A pg. 50
d Enter Button (ENTER) A pg. 20
e Return Button (RETURN) A pg. 28, 30, 46
f Forward Skip Button (T) A pg. 25, 44
Next Button (NEXT) A pg. 28
g Forward Search Button (N) (HDD & DVD deck) A pg. 25,
44
Fast Forward Button (N) (DV deck) A pg. 41
Forward Slow Button (SLOW +) A pg. 26
h Play Button (I) A pg. 24, 39
Select Button (SELECT) A pg. 56
i Pause Button (W) A pg. 24, 39
j Stop Button (o) A pg. 24, 39
Clear Button (CLEAR) A pg. 32
k Skip Search Button (v) A pg. 26, 44
l Set Up Button (SET UP) A pg. 20
m Instant Replay Button (w) A pg. 44
n On-Screen Button (ON SCREEN) A pg. 16, 29
o Progressive Scan Button (PROGRESSIVE SCAN) A pg. 76
p Angle Button (ANGLE) (DVD deck only) A pg. 27
Live Check Button (LIVE CHECK) A pg. 44
How To Use
Before use, insert two AA size batteries into the remote control
with the polarity (F and G) matched correctly as indicated on
the battery compartment or on the lid.
The remote control can operate most of your unit’s functions, as
well as basic functions of TV sets of JVC and other brands.
(A pg. 67)
● Point the remote control toward the receiving window.
● The maximum operating distance of the remote control is
about 8 m.
NOTE:
If the remote control doesn’t work properly, remove its batteries,
wait a short time, replace the batteries and then try again.
A TV/VIDEO Button*
* Not function with this unit.
B DV Button* A pg. 41
* This button will not function during navigation mode or set up mode.
C HDD Button* A pg. 37
* This button will not function during navigation mode or set up mode.
D
E
F
G
H
I
J
K
L
M
N
O
P
Number Keys A pg. 34, 37
Cancel Button (CANCEL(L)) A pg. 32
Auxiliary Button (AUX): Not use on this unit.
Live Button (LIVE) A pg. 44
Dubbing Button (DUBBING) A pg. 57
TV Muting Button (TV MUTING) A pg. 67
Top Menu Button (TOP MENU) A pg. 25
FGD E Buttons A pg. 20
Menu Button (MENU) A pg. 25
Reverse Skip Button (S) A pg. 25, 44, 40
Previous Button (PREVIOUS) A pg. 28
Reverse Search Button (O) (HDD & DVD deck) A pg. 25,
44
Rewind Button (O) (DV deck) A pg. 41
Reverse Slow Button (SLOW –) A pg. 26
Record Button (R) A pg. 34, 37
Jump Button (JUMP +/–) A pg. 40
Recording Mode Button (REC MODE) A pg. 34, 37
Remain Button (REMAIN) A pg. 27, 35
Page 15
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Left+
DVM70S_00.book Page 16 Friday, May 6, 2005 12:06 PM
16 EN INDEX
On-Screen Display (HDD & DVD deck)
When ASUPERIMPOSEB is set to AONB or AAUTOB and
ON SCREEN on the remote control is pressed, various operational
indicators appear on the TV screen. To clear the operational
indicators, press ON SCREEN twice.
When pressing REC MODE
(Appears for eight seconds.)
7: 00
10: 00
20: 00
28: 00
36: 00
When playing back a recorded title
HDD
A Remaining disc time for each recording speed
B Recording speed
0:00
1:00
FISHING WORLD
A
B
C
D
E
F
G
H
XP
SP
LP
EP
FR480
2:00 01:16:48
FR360
Digital
When pressing R during recording
ITR
Title start
Current playback point
Title end
Elapsed playing time
Play mode
Name of title currently being played back
Time scale (This title is an hour and a half long.)
Audio mode
2 : 30
A Recording time for Instant Timer Recording (ITR) mode
When using Live Memory playback
HDD
11:00
12:00
13:00
DVD
TITLE99 CHAPTER999 T. REMAIN6:59:59
XP
Digital
11:35AM
PR.12
11:33AM
FR360
DVD
FISHING WORLD
A
B
C
D
E
F
G
H
I
RAM
Playback title number
Playback chapter number
Disc remaining time
Current status (playback)
Audio mode
Bar meter
Name of title (or play list) currently being played back
Current playback point
Recorded mode
FR360
HDD
11:00
12:00
13:00
11:35AM
11:35AM
PR.12
11:33AM
A Time scale for recording (HDD deck)
Bar meter for recording (DVD deck)
B Current recording point
C Recording mode
D Current time
E Current playback channel position number
F Time scale for Live Memory Playback (HDD deck)
Bar meter for Live Memory Playback (DVD deck)
G Current playback point
H Live Memory playback mode
I Current playback time
When recording
FR360
TITLE99 CHAPTER999 T. REMAIN6:59:59
PR.12
LIVE
DVD
RAM
TITLE99 CHAPTER999 T. REMAIN6:59:59
11:35AM
PR.12
FR360
LIVE
A
B
C
D
Recording point
Current status (recording)
Current time
Recording channel number
Page 16
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right+
DVM70S_00.book Page 17 Friday, May 6, 2005 12:06 PM
INDEX
EN
17
On-Screen Display (DV Dubbing)
On-Screen Display (DV deck)
When capturing images from the external DV
equipment
When ASUPERIMPOSEB is set to AONB or AAUTOB and
ON SCREEN on the remote control is pressed, various operational
indicators appear on the TV screen. To clear the operational
indicators, press ON SCREEN again.
HDD
A
B
C
D
E
F
G
H
I
J
K
0:00
1:00
FR360
00:00:00. 00
12bit
DV
JVC
2:00
DV
GR-DV3500
H
00:00:00. 00
SOUND1
GR-DV3500
G
F
Recording speed
HDD capacity graph
HDD time counter
Recording time scale
HDD mode
Remote control mode
Connected DV equipment mode
Connected DV equipment model information
Input channel
Sound mode
Sound input bit-rate*
E
* Indicates the sound bit-rate of the connected DV equipment
A
B
C
D
L Connected DV equipment information*
* Maker name and model name, etc. may not appear depending on the
connected equipment.
M Time counter for the connected DV equipment
N Sound monitor mode
DV
DV
1
E
F
G
H
RW
L-1
U S E
L WX R
CL E A N IN G
u SP
1 6B I T
CA SS E T T E
0 : 0 0 : 0 0 : 00
A
B
C
D
Operation Mode Indicators
Tape Speed (SP/LP)
Sound Mode Display A pg. 71
Current Month/Day/Year/Clock Display/Time Code Display
A pg. 42
Audio Mode Display A pg. 42
Warning Message
Auxiliary Input Indicator (L-1, F-1 or DV)
ACassette LoadedB Mark
2
O Remote control switch
P Auto capture button
Q Sound monitor switch
179 : 59 : 59
R Elapsed recording time
Page 17
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Left0
DVM70S_00.book Page 18 Friday, May 6, 2005 12:06 PM
18
EN
INSTALLING YOUR NEW UNIT
Basic Connections
Antenna or Cable
Coaxial cable
AC outlet
Flat feeder
Matching transformer
(not supplied)
To [VHF/
UHF IN]
AC power cord
Back of unit
To
[COMPONENT
VIDEO OUT (Y/
PB/PR)]
Component
video cable
(not supplied)
To
[VIDEO
OUTPUT]
To
[AUDIO/
VIDEO
OUT]
To
[S-VIDEO
OUTPUT]
BNC video Audio/Video S-video cable
cable (not supplied)
cable (not
(supplied)
supplied)
To
[VHF/
UHF
OUT]
RF cable
(supplied)
8 S-Video Connection
To connect to TV’s S-VIDEO input and AUDIO input
connectors ^
A Perform A – C of AAV ConnectionB in the left column.
B Connect the unit’s [S-VIDEO OUTPUT] connector to the TV’s
S-VIDEO input connector.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
8 Component Video Connection
To connect to TV’s component video input connectors ^
A Perform A – C of AAV ConnectionB in the left column.
B Connect the unit’s [COMPONENT VIDEO OUT (Y/PB/PR)]
connectors to the TV’s component video input connectors.
C Connect the unit’s [AUDIO OUTPUT] connectors to the TV’s
AUDIO input connectors.
● You can obtain high-quality component video pictures.
● The [COMPONENT VIDEO OUT (Y/PB/PR)] connectors do not
output DV signals.
● If your TV is not stereo-capable, use the unit’s [AUDIO
OUTPUT] connectors to connect to an audio amplifier for Hi-Fi
stereo sound reproduction.
● By using the component video connection, you can view the
images in the progressive mode. For switching to the
progressive mode, refer to AScan Mode Set (HDD & DVD Deck
Only)B (A pg. 76).
4
TV
It’s essential that your unit be properly connected.
Plug the end of the AC power cord into an AC outlet.
This unit performs Plug & Play Set automatically. (A pg. 19)
● The clock and tuner channels will automatically be set when the
antenna is connected and when the AC power cord is first
connected to an AC outlet. (If AAUTOB and the channel indicator
are displayed on the front display panel before the unit is
powered on, the clock and tuner channels are being set
automatically. Wait for the time to be displayed on the front
display panel before turning on the unit.)
● ALOADINGB blinks on the front display panel when the AC plug
of the AC power cord is connected into a AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is
not a malfunction.
ATTENTION:
Connect the AC plug only after all connections to the TV has
been completed.
THESE STEPS MUST BE COMPLETED BEFORE ANY VIDEO
OPERATION CAN BE PERFORMED.
1
2
3
Make sure the package contains all of the accessories listed in
ASPECIFICATIONSB (A pg. 88).
Place the unit on a stable, horizontal surface.
Connect the unit to a TV depending on the TV and cables you
use.
8 AV Connection
To connect to a TV with AV input connectors ^
A Disconnect the TV aerial cable from the TV.
B Connect the TV antenna cable to the [VHF/UHF IN] connector
on the rear panel of the unit.
C Connect the [VHF/UHF OUT] connector on the rear panel of the
unit and the TV’s antenna connector with the supplied RF
cable.
D Connect the supplied audio/video cable between the [AUDIO/
VIDEO OUTPUT] connectors on the rear panel of the unit and
the TV’s audio/video input connectors.
● if your TV is equipped with a BNC video connector, connect an
optional BNC video cable between the unit’s BNC [VIDEO
OUTPUT] connector and the TV’s BNC VIDEO input connector.
Page 18
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right0
DVM70S_00.book Page 19 Friday, May 6, 2005 12:06 PM
INITIAL SETTINGS
Plug & Play Set
Auto Clock Set/Auto Tuner Set
This unit sets the clock and tuner channels automatically when AC
power cord is first connected to an AC outlet. The antenna cable
must be connected for the Plug & Play setting.
The time and date can be set automatically by the clock setting
data transmitted from one of the regular TV broadcast channels.
We call this TV channel the “host channel” and it is a PBS channel
in your area.
ATTENTION:
● If you use a cable box, Plug & Play will not function; set the
clock and tuner channels separately. (墌 pg. 21 – 22)
● Depending on areas or reception conditions, the unit may not
receive the Auto clock setting data from the PBS channel. If
this function is taking a considerable amount of time, it may be
necessary to perform the Semiauto or Manual Clock Set
procedure.
EN
19
1
Connect the antenna cable to the unit. (A pg. 18) Then connect
the AC power cord to an AC outlet. Do not turn on the unit.
The clock and tuner channels will be set automatically.
● ALOADINGB blinks on the front display panel when the AC plug
of the AC power cord is connected into an AC outlet and it takes
approximately 50 seconds for the unit to be turned on. This is
not a malfunction.
NOTES:
● Auto Clock Set is performed first.
AAUTOB blinks on the front display panel during Auto Clock Set.
● Auto Channel Set is performed next. Auto Channel Set scans all
the channels that are receivable by your unit. During Auto
Channel Set, the channel numbers are displayed as they are
scanned and set.
● When Plug & Play setting has been completed successfully, the
correct clock time is displayed. If you perform Plug & Play setting
successfully, there is no need to perform AClock SetB (A pg. 21)
and ATuner SetB (A pg. 22). If, however, you want to add or
delete channels, refer to AManual Channel SetB (A pg. 22).
During Auto Clock Set
AAUTOB blinks.
During Auto Channel Set
The channel numbers are displayed and AAUTOB blinks as they
are scanned and set.
INFORMATION
● If AAUTO CLOCKB is set to AONB (A pg. 21), the clock will be
adjusted automatically by the host channel every hour (except
11:00 PM, midnight, 1:00 AM and 2:00 AM) using the incoming
PBS channel clock setting data. (This automatic clock
adjustment can only be performed when the unit is turned off.
The clock will be adjusted just on these hours — on the time
displayed on the front display panel, not on the actual real
time.) The default setting of AAUTO CLOCKB is AONB.
(A pg. 21)
● If the memory backup fails, because a power outage occurs or
because the AC power cord is unplugged, Plug & Play will be
performed when power is restored to the unit.
Plug & Play Completed
The current time is displayed.
● If an incorrect clock time or AcB appears on the front display
panel, see AWhat to do if Plug & Play setting failedB (A pg. 19).
What to do if Plug & Play setting failed
● If an incorrect time is displayed on the front display panel, you
may be receiving the clock setting data of a PBS channel from
an adjacent time zone, or an incorrect PBS channel from a
cable TV system. In this case, perform ASemiauto Clock SetB
(A pg. 21) or AManual Clock SetB (A pg. 21).
● If AcB appears on the front display panel, your antenna
cable may not be connected to the unit or there may not be a
Host PBS signal available in your area. Ensure that the
antenna cable is connected correctly. Then turn on and off the
unit; the Plug & Play setting will be automatically reactivated. If
Plug & Play setting is not performed though the antenna cable
is connected correctly, perform AManual Clock SetB (A pg. 21)
and AAuto Channel SetB (A pg. 22) or AManual Channel SetB
(A pg. 22).
Page 19
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Left+
DVM70S_00.book Page 20 Friday, May 6, 2005 12:06 PM
20
EN
INITIAL SETTINGS
On-screen Language Set
Language
This unit offers you the choice to view on-screen messages in 3
different languages.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
DVD
DVD
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
5
6
7
ENTER
FGDE
SET UP
Press D E to select AFUNCTION SET UPB, then press G.
Press D E to select ADISPLAY
SETB, then press G.
Press F G to select AON
SCREEN LANGUAGEB, then
press ENTER.
Press F G to select your desired
language, then press ENTER.
DVD VIDEO SET UP HDD/DVD/DV SET UP
REC/PLAY SET UP
DISPLAY SET
INITIAL SET UP
FUNCTION SET UP
VIDEO IN/OUT
SUPERIMPOSE
AUTO
ON
BLUE BACK
BRIGHT
DIMMER
POWER SAVE
OFF
ENGLISH
ON SCREEN LANGUAGE
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press SET UP to complete the
setting.
Menu/Audio/Subtitle Language Set (DVD deck only)
Some DVD discs contain the DVD menu display, audio and
subtitles in multiple languages. With these discs, you can set the
default language as you like.
● The procedure shows how to set AMENU LANGUAGEB as an
example.
1
2
3
4
5
6
Press DVD so that the DVD lamp lights up on the unit.
Press SET UP to access the Main Menu screen.
Press D E to select ADVD VIDEO SET UPB, then press G.
Press D E to select
ALANGUAGE SETB, then press
G.
Press F G to select AMENU
LANGUAGEB, then press
ENTER.
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
LANGUAGE SET
MENU LANGUAGE
PARENTAL LOCK
INITIAL SET UP
DISC PLAY SET UP
ENGLISH
AUDIO LANGUAGE
ENGLISH
SUBTITLE
ENGLISH
Press F G to select your desired
language, then press ENTER.
● See ALanguage Code ListB (A pg. 81).
7
AUDIO OUTPUT
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press SET UP to complete the setting.
NOTE:
When the selected language is not available on the disc, the disc’s
default menu language is played back.
Page 20
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right+
DVM70S_00.book Page 21 Friday, May 6, 2005 12:06 PM
INITIAL SETTINGS
21
8
Clock Set
Perform clock setting only if the clock has not been set correctly by
the Plug & Play setting.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Press F G to select ATIME ZONEB, then press ENTER. Press
F G to select AAUTOB or the desired time zone, then press
ENTER.
● Each time you press F G, the time zone changes as follows:
YAUTOYATLANTICYEASTERNYCENTRALYMOUNTAINY
PACIFICYALASKAYHAWAIIY(back to the beginning)
NOTE:
If an incorrect time is displayed by the Plug & Play function, you
may be receiving the clock setting data of a PBS channel from an
adjacent time zone or from an incorrect PBS channel from a cable
TV system. If you selected AAUTOB for the host channel in step 6,
be sure to select the correct time zone manually.
CABLE/DBS
TV
HDD
EN
DVD
9
DVD
Press SET UP to complete the setting.
IMPORTANT
Turn off the unit after performing Semiauto Clock. AAUTOB will
appear on the front display panel while the clock is being set.
The current clock time will appear automatically when the clock
setting is complete.
ENTER
Auto Daylight Saving Time
This function enables automatic adjustment of the unit’s clock at
the start and end of Daylight Saving Time.
With Auto DST activated, ^
^ on the first Sunday of April at 2:00 AM, the clock is adjusted
to 3:00 AM.
^ on the last Sunday of October at 2:00 AM, the clock is
adjusted to 1:00 AM.
FGDE
SET UP
NOTE:
Timer recording may not function correctly at the time Daylight
Saving Time is adjusted.
Manual Clock Set
Semiauto Clock Set
You can change the host channel/D.S.T. (Daylight Saving Time)/
time zone setting manually.
NOTE:
The time set previously will be erased when AAUTO CLOCKB,
AHOST CHB, AD. S. T.B or ATIME ZONEB setting is changed.
1
2
3
4
5
6
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
Press D E to select AINITIAL SET UPB, then press G.
Press D E to select ACLOCK
SETB, then press G.
DVD VIDEO SET UP
HDD/DVD/DV SET UP
TUNER SET
CLOCK SET
INITIAL SET UP
FUNCTION SET UP
AUTO CLOCK
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
ON
HOST CH [CATV]
AUTO
D. S. T.
AUTO
TIME ZONE
AUTO
Press SET UP to access the Main Menu screen.
Press D E to select AINITIAL SET UPB, then press G.
Press D E to select ACLOCK
SETB, then press G.
Press F G to select AAUTO
CLOCKB, then press ENTER.
Press F G to select AONB, then
press ENTER.
DVD VIDEO SET UP
HDD/DVD/DV SET UP
TUNER SET
CLOCK SET
INITIAL SET UP
FUNCTION SET UP
AUTO CLOCK
5
ON
HOST CH [CATV]
AUTO
D. S. T.
AUTO
TIME ZONE
AUTO
Press F G to select AAUTO
CLOCKB, then press ENTER.
Press F G to select AOFFB,
then press ENTER.
6
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP
HDD/DVD/DV SET UP
TUNER SET
CLOCK SET
Press F G to select AHOST CH
[CATV]B, then press ENTER.
Press F G to select AAUTOB or
the desired PBS channel number, then press ENTER.
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press F G to select AD. S. T.B, then press ENTER. Press F G
to select the desired setting, then press ENTER.
AUTO:
Select if you want to adjust your unit’s clock automatically by
the incoming signal from the host channel. Be sure to select the
correct time zone manually in step 8.
ON:
Adjustment will be made by the built-in clock itself.
INITIAL SET UP
FUNCTION SET UP
OFF
AUTO CLOCK
TIME
– –:– –
DATE
1/1(SAT)
YEAR
2005
Press F G to select ATIMEB,
then press ENTER. Press F G
until the desired time appears,
then press ENTER to start
clock.
● Set the date and year in the same way.
● Holding F G changes the time in 30-minutes interval, or
changes the date in 15-days interval.
D. S. T.
NOTE:
Some PBS channels do not transmit clock setting data.
7
1
7
ON
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press F G to select AD. S. T.B, then press ENTER. Press F G
to select the desired setting, then press ENTER.
ON:
Adjustment will be made by the built-in clock itself.
OFF:
Select when Daylight Saving Time does not apply to you.
8
Press SET UP to complete the setting.
OFF:
Select when Daylight Saving Time does not apply to you.
Page 21
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Left+
DVM70S_00.book Page 22 Friday, May 6, 2005 12:06 PM
22
EN
INITIAL SETTINGS
Manual Channel Set
Tuner Set
You can add the channels you want or delete the channels you do
not want manually.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
DVD
DVD
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
5
Press SET UP to access the Main Menu screen.
6
0-9
Press D E to select AINITIAL SET UPB, then press ENTER.
Press D E to select ATUNER SETB, then press G.
Press FGD E to select AMANUAL CH SETB, then press
ENTER.
Add or skip the desired
channels.
INITIAL SET UP > MANUAL CH SET
BAND
CATV
To add channels
A Press F G to select ACHB, then
press ENTER.
B Press the number keys to enter
a channel number you want to
add, then press ENTER.
C Press F G to select AADD/SKIPB, then press ENTER.
D Press F G to select AADDB, then press ENTER.
E Repeat B – D to add other channels.
CH
ADD/SKIP
ENTER
FGDE
0-9
SET UP
ENTER
EXIT
SELECT
1
ADD
RETURN
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
To skip channels
A Press F G to select ACHB, then press ENTER.
B Press F G to select a channel number you want to skip, then
press ENTER.
C Press F G to select AADD/SKIPB, then press ENTER.
D Press F G to select ASKIPB, then press ENTER.
E Repeat B – D to skip other channels.
SET UP
7
Press SET UP to complete the setting.
INFORMATION
The unit selects the correct band (TV or CATV) automatically
during Auto Channel Set. The selected band will be displayed on
the right side of ABANDB on the Tuner Set screen.
Auto Channel Set
Perform Auto Channel Set only if channels have not been set
correctly by the Plug & Play setting.
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
Press D E to select AINITIAL SET UPB, then press G.
Press D E to select ATUNER
SETB, then press G.
DVD VIDEO SET UP
HDD/DVD/DV SET UP
TUNER SET
CLOCK SET
AUTO CH SET
FUNCTION SET UP
INITIAL SET UP
MANUAL CH SET
GUIDE CH SET
11
5
SET UP
ENTER
EXIT
SELECT
12
13
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press FGD E to select AAUTO
CH SETB, then press ENTER.
You can automatically set the
receivable channels in your
area in the order of their
frequencies.
● When Auto Channel Set is
complete, ASCAN
COMPLETEDB appears on the
TV screen.
● If the scan was unsuccessful, ASCAN COMPLETED –NO
SIGNAL–B appears on screen. Check the connections and start
again.
INITIAL SET UP > AUTO CH SET
AUTO CHANNEL SET
SCANNING...
CANCEL
6
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Press SET UP to complete the setting.
Page 22
Friday, 6 May 2005 12:06
Filename [DVM70S_05Name.fm]
Masterpage:Right+
DVM70S_00.book Page 23 Friday, May 6, 2005 12:06 PM
INITIAL SETTINGS
Monitor Set
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
DVD
EN
1
2
Press DVD so that the DVD lamp lights up on the unit.
3
4
Press D E to select AFUNCTION SET UPB, then press G.
23
Press SET UP to access the Main Menu screen.
● You cannot set the monitor type during recording or playback.
5
Press D E to select AVIDEO IN/
OUTB, then press G.
DVD VIDEO SET UP
HDD/DVD SET UP
FUNCTION SET UP
REC/PLAY SET UP
DISPLAY SET
VIDEO IN/OUT
Press F G to select AMONITOR
TYPEB, then press ENTER.
6
Press F G to select the desired
option, then press ENTER.
7
Press SET UP to complete the
setting.
INITIAL SET UP
MONITOR TYPE
4:3LB
FRONT AUX F-1
VIDEO
REAR AUX L-1
VIDEO
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
* The boldface settings below indicate the settings at your purchase.
8 MONITOR TYPE - 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
4:3LB (Letter Box conversion):
ENTER
FGDE
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars appear
on the top and the bottom of the screen.
4:3PS (Pan&Scan):
Select this when the aspect ratio of your TV is 4:3 (conventional
TV). While viewing a wide screen picture, the black bars do not
appear; however, the left and right edges of the pictures will not
be shown on the screen.
SET UP
16:9AUTO (Wide television conversion):
Select this when the aspect ratio of your TV is 16:9 (wide TV).
16:9FIX (Wide television conversion):
Select this when the aspect ratio of your TV is fixed to 16:9
(wide TV). The unit automatically adjusts the screen width of
the output signal correctly when playing back a picture whose
aspect ratio is 4:3.
Pan&Scan/Letter Box
In general, DVD VIDEO disc are produced for a wide-screen TV
with 16:9 aspect ratio.
Material with this ratio will not fit to a TV with 4:3 aspect ratio.
There are two styles to display the image, APan&ScanB (PS) and
ALetter BoxB (LB).
Pan&Scan
The right and left side of the image are cut off.
The image fills the screen.
● The picture will be shown in the A4:3LBB mode
depending on the disc even if the A4:3PSB
mode is selected.
Letter Box
Black bands appear at the top and bottom of
the image. The image itself appears in 16:9
aspect ratio.
Page 23
Friday, 6 May 2005 12:06
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left0
DVM70S_00.book Page 24 Friday, May 6, 2005 12:06 PM
24
EN
BASIC OPERATIONS ON DVD DECK
To play back an MP3/JPEG disc, see APlayback With MP3/WMA/
JPEG NavigationB (A pg. 56).
Basic Playback
1
Load a disc.
● For details, refer to APlacing A DiscB (A pg. 10).
● Pressing I also closes the disc tray.
● Playback begins automatically if an auto-playback DVD disc is
loaded.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
o
I
W
CABLE/DBS
TV
Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
3
Press I to start playback.
● If you load a DVD disc whose region code does not match the
DV/HDD/DVD
M
2
DVD
DVD
unit, AREGION CODE ERRORB appears on the TV screen. For
details, refer to ARegion NumberB (A pg. 8).
● If ACAN NOT PLAY BACK DISC UNDER CURRENT SETTINGB
appears on the TV screen, refer to AParental LockB (A pg. 33).
● With Video CD/SVCD discs with PBC control or some DVD
discs, the menu display may appear on the TV screen after
starting playback. In this case, select an item which you want to
play back from the menu. Otherwise, the playback cannot go
forward. Refer to APlayback Control (PBC) FunctionB (A pg. 28)
or ALocating A Desired Scene Using The DVD MenuB
(A pg. 25).
● The Library Database Navigation also enables you to search
and select the desired titles. (A pg. 51)
4
Press W to pause playback.
5
Press o to stop playback.
● To resume normal playback, press I.
● When a recordable disc is played, playback stops and a
ENTER
I
o
W
ATTENTION:
● It takes approximately 30 seconds to read a disc depending on
the type and condition of the disc since this unit is multi-disc
compatible (DVD-RAM, DVD-RW, DVD-R). It may even take
several minutes when a disc is dirty, scratched or warped.
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
Page 24Friday, 6 May 2005 12:06
program received with the unit’s tuner resumes on the TV
screen.
● When a playback-only disc is played, playback stops and the
TV screen becomes all blue when you press o. Pressing o
again resumes a program received with the unit’s tuner.
● If M is pressed during playback, playback stops, then the disc
tray opens.
NOTES:
● When the Library Database Navigation screen appears, choose
a thumbnail image of the desired title on the TV screen, then
press ENTER. (A pg. 51)
● It is not possible to playback the DVD disc recorded in 96 kHz on
DVD during recording or Live Memory Playback on HDD.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 25 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
25
Locating The Start Point Of The Item Or Skip The Item
Playback Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
CABLE/DBS
TV
EN
Press S or T during playback.
● Pressing T locates the start point or marked points of the item
or skips the item in the forward direction, then resumes playback.
● Pressing S locates the start point or marked points of the item
or skips the item in the reverse direction, then resumes playback.
DVD
Current playback point
DVD
0-9
TOP MENU
ENTER
MENU
S
I
O/SLOW o
JUMP JUMP +
FGDE
T
N/SLOW +
W
Locating A Desired Scene Using The DVD Menu
DVD VIDEO discs may have top menu and disc menu.
Top menu
DVD discs generally have their own menus which show the disc
contents. These menus contain various items such as titles of a
movie, names of songs, or artist information. You can locate a
desired scene by using the top menu displayed on the TV screen.
Press TOP MENU to access the top menu.
Disc menu
Disc menus include playback data (angle menu, subtitle menu,
etc.) specific to each title.
Press MENU to access the disc menu.
1
Previous
program
or
Scene 2
(Chapter 2)
or
Track 2
Press TOP MENU or MENU to
access the DVD menu.
Drama
or
Scene 3
(Chapter 3)
or
Track 3
Next program
or
Scene 4
(Chapter 4)
or
Track 4
Movie
or
Scene 5
(Chapter 5)
or
Track 5
Forward
Reverse
● : marked points (A pg. 27)
Variable Speed Search
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
For Audio CD
You can perform 4 levels of speed search with N and O. (Audio
is active also during variable speed search.) You cannot perform
slow motion for each direction.
Reverse O
N Forward
Reverse
Reverse Search Reverse
Normal Forward Search
Slow Motion Slow Motion
4 steps
Play
Play
4 steps
3 steps
3 steps
-60 -15 -5 -3
-1
-½ -¼ -116 116
¼ ½
1
3
5
15
Still Picture/Frame-By-Frame Playback
2
Press FGD E to select a
desired title, then press
ENTER. Playback starts.
● It may be possible to select the
desired item using the number
keys depending on the menu
display.
Example:
NOTE:
When A7B appears on the TV screen in step 1, the disc does not
have a top menu or disc menu.
Page 25Friday, 6 May 2005 12:06
1
2
Press W to pause during playback.
Press SLOW – (O) or SLOW + (N) to activate frame-byframe playback.
● Each press of SLOW – (O) or SLOW + (N) advances/
reverses the still picture frame by frame.
● Frame-by-frame playback for reverse direction cannot be
performed with Video CD/SVCD discs.
● To resume normal playback, press I.
60
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 26 Friday, May 6, 2005 12:06 PM
26 EN BASIC OPERATIONS ON DVD DECK
Slow Motion
1
2
Resume Function
Press W to pause during playback.
Press SLOW – (O) or SLOW + (N) for 2 or more seconds.
● Each press of SLOW – (O) or SLOW + (N) increases the
slow motion speed for each direction.
● Slow motion for reverse direction cannot be performed with
Video CD/SVCD discs.
1
Skip Search
Jump Search
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (A pg. 72)
during playback (or Live Memory Playback).
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP +
repeatedly within 5 seconds of each press to continue jump.
● Depending on the time from where you want to start jump search,
the first press of JUMP – or JUMP + will not necessarily lead to a
jump of the selected time interval. The first press will lead to a
jump to the nearest quarter points of an hour (15 min/ 30 min/ 45
min/ 00 min). The subsequent jumps will then be in accordance
to the selected time interval.
● When you cannot advance any further (beginning or end of
program reached), the message AUNABLE TO GO BACK ANY
MOREB appears on the screen and the on-air screen resumes. In
such a case, press S, O or o.
Example:
Playback search when jump interval is set to 15 MIN jumps.
Taking for instance, you want to start jump search 40 minutes after
the beginning of the program. Pressing JUMP – or JUMP + will
result in a jump to the scene at the 30 minutes point or 45 minutes
point respectively as illustrated below. At the subsequent press, the
scene will jump to the 15 minutes point or 1 hour point respectively,
according to the selected time interval, which in this case is A15 MINB.
Beginning of program
Press o during playback to memorize a resume point.
● The unit enters Resume Stop mode and memorizes the
During playback, press v.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
● Skip search cannot be performed when a VCD/SVCD disc is
being played back with the PBC function.
Time counter
0 min
15 min
It is possible to memorize the position where you stop playback
and resume playback from that position.
● Be sure to set ARESUMEB to AONB or ADISC RESUMEB.
(A pg. 71)
● Resume function always works for DVD-R/DVD-RW discs that
have not been finalized and DVD-RAM regardless of the setting
of ARESUMEB.
30 min
40 min
45 min
Current scene
1 h 15 min
1h
End of program
NOTE:
Jump search cannot be performed with finalized DVD-R/DVD-RW
(video mode) discs.
Page 26Friday, 6 May 2005 12:06
position where you have stopped playback as a resume point.
(The inside of the disc status indicator on the front display panel
blinks while memorizing.)
● The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected if
ARESUMEB is set to ADISC RESUMEB. (A pg. 71)
● To clear the resume points:
(The inside of the disc status indicator stops blinking and
lights.)
When ARESUMEB is set to AONB:
• Press A to turn off the unit.
• Press M to take out the disc.
• Press o in stop mode.
• Press TOP MENU to display the top menu, then start playback
by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
When ARESUMEB is set to ADISC RESUMEB:
• Set ARESUMEB to AOFFB. (A pg. 71)
• Press o in stop mode.
• Press TOP MENU to display the top menu, then start playback
by selecting an item, etc.
• Press MENU to display the disc menu, then start playback by
selecting an item, etc.
2
Press I in stop mode to resume playback. The unit starts
playback from the resume point.
NOTES:
● ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under AONB setting will be applied
even if ARESUMEB is set to ADISC RESUMEB. (A pg. 71)
● If you stop the playback of a disc for which a resume point has
already been memorized, the memory will be updated with the
new resume point.
● After the unit has memorized the resume points for 30 discs,
remembering a new resume point will cause the unit to delete the
oldest memorized point. Stopping playback of a disc for which a
resume point is already stored may change the order in which the
points are stored. This may potentially change the order in which
points are deleted.
● When the unit memorizes a resume point for a disc, it also
remembers audio language, subtitle and angle settings.
● This function may not work for some Video CD/SVCDs.
● When ARESUMEB is changed to AONB or AOFFB (A pg. 71),
resume points of the discs memorized with ARESUMEB set to
ADISC RESUMEB will be cleared.
● Resume points are memorized for each side of a double-sided
disc.
● When you switch to HDD while playing back JPEG/MP3 files,
playback stops. The Resume Function doesn’t work when you
switch to DVD thereafter to playback the disc.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 27 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
CABLE/DBS
TV
EN
27
Checking The Time Information
DVD
DVD
You can check time information of a disc on the front display panel
and the TV screen.
0-9
FGDE
8 DVD-RAM/DVD-R/DVD-RW
Each press of DISPLAY on the remote control or the unit changes
the display as follows:
During recording
Clock time (front display panel only) N Current title elapsed time
N Disc remaining time* N (back to the beginning)
RETURN
* only discs before finalizing
T/NEXT
During playback
Each title elapsed time N Current title elapsed time N
Disc remaining time* N (back to the beginning)
MARK
ENTER
MENU
S/PREVIOUS
I
o
REC MODE/REMAIN
DISPLAY
SET UP
AUDIO
SUBTITLE
ANGLE
* only discs before finalizing
Marking Positions To Play Back Again Later
It is possible to mark positions (up to 999 points) where you want
to play back once again later, and start playback from a marked
position. Marking onto DVD-RAM/RW (VR mode only) discs when
recording is helpful to locate a start point when you play back the
discs later.
To mark positions:
During playback, press MARK at
positions you want to mark.
● AMARKB appears on the TV screen.
You can easily locate the marked
positions using S or T when
you play back the disc.
To delete the marked positions:
While paused, press S or T to
locate a marked position you want to
delete, then press MARK.
● Crossed AMARKB appears on the
TV screen, and the marked position
is deleted.
NOTES:
● When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
● For DVD-R/RW (Video mode) discs, marks are assigned
automatically every 5 minutes.
● If MARK is pressed when playing back a disc that does not allow
marks to be inserted, A7B appears on the TV screen.
Page 27Friday, 6 May 2005 12:06
During recording/playback or in stop mode
Press REC MODE.
● The disc remaining time according to recording modes appears
on the TV screen.
● It is possible to check disc remaining time according to recording
modes also by pressing REMAIN.
● In FR mode, it is possible to set recording time in detail. While the
recording mode and the disc remaining time are displayed by
pressing REMAIN, press F G to select AFRB, then press D E to
select the desired recording time. (A pg. 36)
● It is not possible to switch the recording mode during playback or
while recording.
8 Video CD/SVCD/Audio CD
During playback or in stop mode
Current track elapsed time N Current track remaining time N Total
elapsed time N Total remaining time N (back to the beginning)
NOTE:
When a PBC-compatible Video CD/SVCD disc is loaded,
deactivate the PBC function. (A pg. 28)
Angle Selection
You can enjoy a variety of scene angles if a DVD VIDEO disc
contains Amulti-angleB parts, where the same scene was shot from
different angles.
If the disc contains Amulti-angleB parts, AyB appears on the TV
screen at the beginning of the Amulti-angleB part.
1 Press ANGLE during
playback. The angle selection
display appears on the TV
When 3 scene angles are
screen.
contained.
2
Press ANGLE or D E to select
your desired angle.
● Each time you press ANGLE or D E, the angle changes.
● When A7B appears on the TV screen, the current scene is not
recorded from multiple angles. In addition, some discs prohibit
angle selection.
● To clear the angle selection display, press ENTER. In addition,
the angle selection display disappears automatically if no
operation is done for 10 seconds.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 28 Friday, May 6, 2005 12:06 PM
28 EN BASIC OPERATIONS ON DVD DECK
Subtitle Selection
Audio Language/Sound Selection
Some DVD VIDEO discs contain more than one subtitle language,
from among which you can choose the desired subtitle language.
AhB appears on the TV screen at the beginning of the part where
more than one subtitle language are recorded.
Some DVD VIDEO discs contain the multiple audio language or
sound. You can select the desired audio language or sound. For
some Video CD/SVCD discs, you can switch the audio channel to
choose Karaoke either with or without the vocal.
1
1
Press SUBTITLE during
playback. The subtitle
selection display appears on
the TV screen.
● Each time you press
SUBTITLE, the subtitle display
is switched on and off.
2
ENGLISH
When 3 subtitle languages are
contained.
Press D E to select your desired language.
● To clear the subtitle selection display, press ENTER.
NOTES:
● When A7B appears on the TV screen, no subtitle language is
recorded.
● When the subtitle language won’t be changed with the procedure
above, change the subtitle on a disc menu displayed by pressing
MENU.
Audio Channel Selection
When watching bilingual programs or playing discs on which you
recorded bilingual or stereo programs, you can choose the desired
audio channel.
● When ASUPERIMPOSEB is set to AONB or AAUTOB, you can
confirm on the TV screen the audio channel you have chosen.
(A pg. 72)
● Each time you press AUDIO, the audio
channel changes.
TRACK
USE
On-Screen Display
For stereo discs
For audio of left channel
For audio of right channel
When you can’t switch the audio channel of a bilingual
program
When the unit is connected with a digital audio device using an
optional optical cable and ADIGITAL AUDIO OUTB is set to
ADOLBY DIGITAL/PCMB, it is not possible to switch the audio
channel of a bilingual program recorded on a DVD-RAM or
DVD-RW (VR mode) disc. (A pg. 69) In this case, perform the
following steps using the remote control to switch ADIGITAL
AUDIO OUTB from ADOLBY DIGITAL/PCMB to APCM ONLYB.
A Press SET UP to access the Main Menu screen.
B Press D E to select ADVD VIDEO SET UPB, then press G.
C Press D E to select AAUDIO OUTPUTB, then press G.
D Press F G to select ADIGITAL AUDIO OUTB, then press
ENTER.
E Press F G to select APCM ONLYB, then press ENTER.
(A pg. 70)
F Press SET UP to complete the setting.
G Press AUDIO to select the desired audio channel.
Page 28Friday, 6 May 2005 12:06
Press AUDIO during playback.
The Audio Language/Sound
selection display appears.
For example: DVD VIDEO
2
Press AUDIO or D E to select
When 3 audio languages are
your desired audio language/
contained.
sound.
● Each time you press AUDIO or D E, the audio language/sound
changes.
● To clear the Audio Language/Sound selection display, press
ENTER.
NOTES:
● When A7B appears on the TV screen, no audio language is
recorded.
● When the audio language won’t be changed with the procedure
above, change the audio on a disc menu displayed by pressing
MENU.
● Pressing AUDIO to select the audio language/sound is only
possible during playback. It is not possible to select by pressing
AUDIO in stop mode. However, you can select the desired audio
language/sound from the setup menu while in stop mode.
Playback Control (PBC) Function
Some Video CD/SVCD discs support the PBC function. PBC is an
abbreviation of APlay Back ControlB. A Video CD/SVCD disc
recorded with PBC has its own menus, such as a list of the songs
on the disc. You can locate a specific scene by using the menu.
1
2
Press I in stop mode. The PBC menu appears.
Press the number keys to enter the number of the desired
scene, then press ENTER. The unit starts playback of the
selected item.
● APBCB appears on the front display panel.
● When ANEXTB or APREVIOUSB appears on the TV screen:
Pressing NEXT(T) advances to the next page.
Pressing PREVIOUS(S) returns to the previous page.
● You can return to the menu by pressing RETURN.
● The method of the operation is different depending on the disc.
NOTE:
If you want to playback a PBC-compatible Video CD/SVCD disc
without activating the PBC function, start playback with the PBC
function, then press o to stop playback. The TV screen becomes
all blue. Then start playback in stop mode by using the number
keys to choose the track, then press ENTER.
Instant Replay
You can move back the playback position slightly.
Press w on the remote control or INSTANT REPLAY on the unit.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 29 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
A
B
C
D
E
F
Using The On-screen Bar
The on-screen bar allows you to control various playback
functions. Some of the functions operated on Navigation Menu can
be controlled on the On-screen bar.
ATTENTION:
The on-screen bar can also be used for the HDD deck.
Be sure to clear Library Database Navigation screen by pressing
NAVIGATION.
CABLE/DBS
TV
DVD
G
H
I
J
K
L
EN
29
Disc type.
Select this for Repeat Playback. (A pg. 29)
Select this for A-B Repeat Playback. (A pg. 30)
Select this for search function. (A pg. 30)
Select this for time search function. (A pg. 31)
Select this to switch Simulated Surround Effect function.
(A pg. 31)
Select this for Picture Control function. (A pg. 31)
Select this to switch picture source type. (A pg. 32)
Current status area for the selected item.
Select this for Program Playback. (A pg. 32)
Select this for Random Playback. (A pg. 32)
Select this to control the switching interval of the slide show.
(A pg. 32)
NOTE:
Although examples of the on-screen bar are provided here only for
3 types of discs, the on-screen bar will be displayed for whichever
disc indicated in the left column.
Basic Operation On The On-screen Bar
Example: When selecting Picture Control function of DVD
During playback or while stopped
1
NAVIGATION
ENTER
Press ON SCREEN twice to access the on-screen bar. The
item currently selected is highlighted and pointed by :.
TITLE 99
FGDE
CHAPTER 99
3D-ON
DVD-
RETURN
EACH 0:00
CINEMA
AUTO
VIDEO
2
Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
ON SCREEN
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
3
Press F G to select the desired option, then press ENTER.
TITLE 99
How To Access The On-screen Bar
1
CHAPTER 99
EACH 0:00
3D-ON
DVD-
Press ON SCREEN twice whenever a disc is loaded.
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
To clear the on-screen bar
Press ON SCREEN.
NOTE:
See the corresponding pages for details on each menu item.
Repeat Playback
Video CD/SVCD
TRACK 99
EACH 0:00
CINEMA
VCD
You can repeat playback as you like according to the type of disc.
1
2
JPEG disc
Press ON SCREEN twice to access the on-screen bar.
Press D E to select AxB, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
GROUP 99 TRACK 99
JPEG
AUTO
NORMAL
CINEMA
SHARP
SOFT
Contents of the on-screen bar during playback
DVD VIDEO
TITLE 99
CINEMA
VIDEO
DVD-
EACH 0:00
3D-ON
CINEMA
AUTO
VIDEO
5 sec
Page 29Friday, 6 May 2005 12:06
CHAPTER 99
3
Press F G repeatedly to select the desired Repeat mode, then
press ENTER.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left+
DVM70S_06DVD Operation.fm Page 30 Thursday, June 2, 2005 6:06 PM
30
EN
BASIC OPERATIONS ON DVD DECK
To cancel A-B Repeat Playback
Press D E to select AA-B xB, then press ENTER.
DVD-RAM/RW/R
OFF:
NOTES:
Repeat playback is not performed.
● A-B Repeat Playback may not work properly depending on the
ALL REPEAT:
type of disc being used.
The whole disc is played back repeatedly.
● The subtitles recorded around the A-B point may not appear.
● When the end of the item is reached before the end point is set,
TITLE REPEAT:
The current title is played back repeatedly.
the on-screen bar disappears from the TV screen. In such a
case, repeat the procedure from step 1.
● The point B must be set at least 3 seconds after the point A.
● When playing back a DVD, A-B Repeat Playback is possible only
within the same title.
● AA-B xB cannot be selected during Program and Random
Playback.
● AA-B xB cannot be selected while stopped.
DVD VIDEO
OFF:
Repeat playback is not performed.
TITLE REPEAT:
The current title is played back repeatedly.
CHAPTER REPEAT:
The current chapter is played back repeatedly.
Locating The Beginning Of A Desired Selection
Audio CD/Video CD/SVCD/JPEG/MP3
OFF:
Repeat playback is not performed.
ALL REPEAT:
You can locate the beginning of a title, chapter, group or track.
The whole disc is played back repeatedly.
During playback or while stopped
TRACK REPEAT*:
1
2
3
The current track is played back repeatedly.
* ATRACK REPEATB cannot be selected for JPEG discs.
To clear the on-screen bar
Press ON SCREEN.
Press ON SCREEN twice to access the on-screen bar.
Press D E to select A9B, then press ENTER.
Press F G to select the desired item, then press ENTER.
● Skip this step for Video CD/SVCD and Audio CD.
To cancel Repeat Playback
Repeat the above procedure from step 1, select AOFFB in step 3,
then press ENTER.
NOTES:
● Repeat Playback is not possible for a Video CD/SVCD with PBC
function.
● Repeat Playback may not work properly depending on the type of
the disc being used.
● It is possible to use Mode Lock function. (A pg. 76)
For DVD-RAM/RW/R, DVD VIDEO
ATITLE SEARCHB or ACHAPTER SEARCHB is selectable.
(However, only ATITLE SEARCHB is selectable while stopped.)
For JPEG, MP3
AGROUP SEARCHB or ATRACK SEARCHB is selectable. (However,
only AGROUP SEARCHB is selectable while stopped.)
For Video CD/SVCD, Audio CD
ATRACKB is selectable.
NOTE:
Settings that are selectable during playback and stop mode differ
depending on the type of disc and search used.
A-B Repeat Playback
GROUP 99
You can repeat the desired part.
DVD-
Press D E to select AA-B xB.
Press ENTER at the beginning of the desired part you want to
repeat (point A). The elapsed playing time of the point A
appears.
CHAPTER 99
EACH 0:00
3D-ON
DVD-
CINEMA
AUTO
VIDEO
A
1 : 25 : 58
B
:
Press ENTER at the end of the desired part you want to repeat
(point B). The elapsed playing time of the point B appears.
● The selected part of the disc (between point A and B) is played
repeatedly.
CHAPTER 99
EACH 0:00
3D-ON
DVDVIDEO
A
1 : 25 : 58
B
To clear the on-screen bar
Press ON SCREEN.
Page 30Thursday, 2 June 2005 18:06
1 : 40 : 00
4
Press the number keys to enter the desired item number, then
press ENTER.
● Playback starts from the selected section.
Examples:
A To select track 5, press the number key A5B.
B To select track 15, press the number key A1B and A5B.
C To select track 25, press the number key A2B, then A5B.
If you have specified a wrong selection
Press RETURN on the remote control and repeat the above
procedures from step 2.
:
4
TITLE 99
CINEMA
TITLE SEARCH
CHAPTER SEARCH
Press ON SCREEN twice to access the on-screen bar.
TITLE 99
EACH 179:59
5
VIDEO
During playback
1
2
3
CHAPTER 99
CINEMA
AUTO
To clear the on-screen bar
Press ON SCREEN.
NOTES:
● When A7B is displayed on the TV screen in step 4, the chapter
you have selected is not contained in the disc, or chapter search
does not work on the disc.
● Before you press ENTER, playback may start automatically when
you enter the section’s number depending on the disc.
● This function is not possible for a Video CD/SVCD with PBC
function.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 31 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
31
Simulated Surround Effect
CABLE/DBS
TV
EN
DVD
It is possible to get a simulated surround effect from your stereo
system. You can enjoy the virtual surround sound with your 2channel stereo system.
0-9
1
2
CANCEL
Press ON SCREEN twice to access the on-screen bar.
Press D E to select A
B, then press ENTER.
● A3D-ONB appears above the selected item and Simulated
ENTER
Surround Effect is activated.
FGDE
● Each time you press ENTER, A3D-ONB appears and disappears
RETURN
T
S
alternately.
TITLE 99
I
CLEAR
CHAPTER 99
EACH 0:00
3D-ON CINEMA
DVD-
AUTO
VIDEO
ON SCREEN
To clear the on-screen bar
Press ON SCREEN.
To cancel the simulated surround effect
Press ENTER to clear A3D-ONB from the screen.
Time Search
You can play back a disc from the desired point by specifying the
elapsed playing time from the beginning of a program (DVD-RAM,
DVD-R, DVD-RW, DVD VIDEO and HDD) or a disc (Video CD/
SVCD and Audio CD).
1
2
Press ON SCREEN twice to access the on-screen bar.
Press D E to select Aj9B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
CINEMA AUTO
DVD-
NOTES:
● Simulated Surround Effect works correctly only when playing
back a title recorded in multichannels.
● Simulated Surround Effect does not affect the DVD VIDEO
bitstream signal from the [DIGITAL AUDIO OUT] connectors.
● When Simulated Surround Effect is activated, the settings of
AANALOG AUDIO OUTB and AD. RANGE CONTROLB are
disabled. (A pg. 70)
● Simulated Surround Effect cannot be activated under the
following conditions:
● When the HDD deck is in the recording mode.
● When the HDD or DVD deck is in the timer standby mode.
● When a disc containing both the Dolby Digital 5.1CH and 2CH
sound formats is playing back a scene that is not in the 5.1CH
sound format.
Adjusting The Picture Quality
VIDEO
3
Press the number keys to enter the time, then press ENTER.
Playback starts from the specified time.
Example:
To play back from a point 12 (minutes): 50 (seconds) elapsed.
TIME
TIME
Press 1
TIME
You can obtain optimal picture quality by selecting an appropriate
picture mode.
1
2
Press 2
Press 0
EACH 0:00
CINEMA AUTO
VIDEO
3
Press F G to select the desired option, then press ENTER.
NORMAL:
Normally select this option.
To clear the on-screen bar
Press ON SCREEN.
CINEMA:
NOTES:
● When A7B is displayed on the TV screen in step 3, you have
selected a point that exceeds the recording time of the disc.
● Some DVD VIDEO discs do not contain time information, and it is
not possible to use the Time Search function. In such cases, A7B
is displayed on the TV screen as well.
● This function is not possible for a Video CD/SVCD with PBC
function.
SHARP:
Page 31Friday, 6 May 2005 12:06
CHAPTER 99
DVD-
TIME
If you have specified a wrong selection,
Press RETURN on the remote control and repeat the above
procedures from step 2.
Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
TIME
Press 5
Press ON SCREEN twice to access the on-screen bar.
Suitable for a movie disc, etc.
Clearer, sharper-edged picture when viewing images with lots
of flat, same-colored surfaces such as cartoons.
SOFT:
Select this option when too much noise appears.
To clear the on-screen bar
Press ON SCREEN.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 32 Friday, May 6, 2005 12:06 PM
32 EN BASIC OPERATIONS ON DVD DECK
Setting The Progressive Mode
4
You can obtain optimal picture quality by selecting whether the content on
the disc is processed by field (video source) or by frame (film source).
1
2
3
Set the unit to the progressive scan mode. (A pg. 76)
Press ON SCREEN twice to access the on-screen bar.
Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
TITLE 99
CHAPTER 99
EACH 0:00
3D-ON
DVD-
Press I. Playback starts in the programmed order.
● When all of the programmed tracks have been played back,
CINEMA AUTO
Program Playback stops, but the programmed information
remains.
● To add tracks to the end of the program, perform steps 1
through 3.
To clear the on-screen bar and the contents of the program
Press ON SCREEN.
To cancel Program Playback
Press D E to select APRGMB, then press ENTER.
NOTE:
Program Playback is not possible depending on the type of disc.
Random Playback
VIDEO
4
Press F G to select the desired option, then press ENTER.
You can play back all the tracks on the disc in random order.
AUTO:
This mode automatically detects film and video content for
progressive playback. When film content is found, flag
detection is used to invoke playback of film data in full screen.
When video content is found, pictures from multiple fields are
used to detect sections with movement, and then this
movement undergoes advanced image processing for output of
sharp, detailed progressive images without any reduction in
image quality where movement occurs. Normally, operation in
this mode is recommended.
FILM:
Suitable for playing back a progressive scanned film source
disc.
VIDEO:
Suitable for playing back a video source disc. The outlines on
the played back pictures will be soft.
To clear the on-screen bar
Press ON SCREEN.
1
2
Press ON SCREEN twice to access the on-screen bar.
Press D E to select ARNDB, then press ENTER. Playback starts
in random order.
TRACK 99
You can program up to 30 tracks (Video CD/SVCD or Audio CD) to
play back in the desired order.
While stopped
To clear the on-screen bar
Press ON SCREEN.
To cancel Random Playback
Perform steps 1 and 2.
NOTE:
The same track will not be played back more than once during
Random Playback.
You can control the switching interval of the slide show.
1
2
Press ON SCREEN twice to access the on-screen bar.
Press D E to select A
B, then press ENTER. The pop-up
window appears under the selected item.
GROUP 99 TRACK 99
Press D E to select APRGMB, then press ENTER. The program
table appears under on-screen bar.
JPEG
EACH 0:00
VCD
3
CINEMA
Press the number keys to
USE [0-9] KEYS TO SELECT TRACK
enter the track numbers in the
desired order.
Examples:
A To select track 5, press the
number key A5B and ENTER.
B To select track 15, press the
Program Total Time
number key A1B and A5B.
C To select track 25, press the number key A2B and A5B.
If you have specified a wrong selection
Press CANCEL(L). The last selection is erased.
Or press CLEAR (o). The whole selection is erased.
Page 32Friday, 6 May 2005 12:06
CINEMA
VCD
Press ON SCREEN twice to access the on-screen bar.
TRACK 99
EACH 0:00
Select The Switching Interval Of The Slide Show
Program Playback
1
2
While stopped
3
5 sec
Press F G to select the desired option, then press ENTER.
● Each time you press F G, the interval changes as follows:
5 sec Y 10 sec Y 15 sec Y 20 sec Y 25 sec Y 30 sec Y
(Back to the beginning)
To clear the on-screen bar
Press ON SCREEN.
NOTE:
JPEG files are played back as a slide show. It may take more time
to display an image with larger file size.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 33 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
Parental Lock
EN
8
Press F G to select your country code, then press ENTER.
9
Press the number keys to enter the same password as in
step 6 above, then press ENTER.
33
● If you do not need to change your country code, jump to 10.
● See ACountry/Area Code List for Parental LockB (A pg. 82)
This function restricts playback of DVD VIDEO discs which contain
violent (and other) scenes according to the level set by the user.
For example, if a movie which includes violent scenes supports the
parental lock feature, such scenes which you do not want to let
children view can be cut or replaced by other scenes.
NOTE:
Remember your password, or make a note of it.
To Change The Settings
You can change the Parental Lock settings later.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD so that the DVD lamp lights up on the unit.
1
Perform steps 1 to 3 of ATo Set Parental Lock For The First
TimeB to access the APARENTAL LOCKB screen before
continuing.
To change the level
CABLE/DBS
TV
10 Press SET UP to complete the setting.
2
3
DVD
DVD
Press F G to select APARENTAL LEVELB, then press ENTER.
Press F G to select the desired level, then press ENTER.
To change the country code
0-9
4
5
Press F G to select ACOUNTRY CODEB, then press ENTER.
6
Press the number keys to enter the same password as in
step 6 of ATo Set Parental Lock For The First TimeB, then press
ENTER.
7
Press SET UP to complete the setting.
Press F G to select your country code, then press ENTER.
● See ACountry/Area Code List for Parental LockB (A pg. 82).
ENTER
FGDE
NOTE:
If you forget your password, enter A8888B in step 6.
To Temporarily Release Parental Lock
When you set the Parental Lock level strictly, some discs may not
be played back at all. When you insert such a disc and try to play it
back, the confirmation screen appears on the TV screen, asking
you whether you want Parental Lock to be temporarily released or
not.
SET UP
1
Load a disc.
● If the disc is rated higher than the selected level, the
confirmation screen appears.
To Set Parental Lock For The First Time
2
While stopped
1
2
3
3
Press SET UP to access the Main Menu screen.
Press D E to select ADVD VIDEO SET UPB, then press G.
Press D E to select
APARENTAL LOCKB, then
press G.
DVD VIDEO SET UP HDD/DVD/DV SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LEVEL
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC PLAY SET UP
NONE
US
COUNTRY CODE
4
Press F G to select
APARENTAL LEVELB, then
press ENTER.
5
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
DVD VIDEO SET UP HDD/DVD/DV SET UP
LANGUAGE SET
AUDIO OUTPUT
PARENTAL LEVEL
Press F G to select the
desired level, then press
ENTER.
● The smaller the value of level
is, the more restrictive the
Parental Lock level becomes.
● Select ANONEB to cancel the restriction.
FUNCTION SET UP
INITIAL SET UP
PARENTAL LOCK
DISC PLAY SET UP
NONE
US
COUNTRY CODE
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
6
Press the number keys to enter your desired four-digit number,
then press ENTER.
● If you made a mistake, enter a correct number again.
7
Press F G to select ACOUNTRY CODEB, then press ENTER.
Page 33Friday, 6 May 2005 12:06
Press D E to select AYESB, then press ENTER.
● If you select ANOB, you cannot play back that disc.
Press the number keys to enter the same password as in
step 6 of ATo Set Parental Lock For The First TimeB, then press
ENTER.
● When you enter the correct password, the Parental Lock is
released and the unit starts playback.
● If you enter a wrong password, AENTRY ERRORB appears on
the TV screen. Enter the correct password.
● If you have successively entered wrong password three times,
AENTRY ERROR CAN NOT CHANGE PASSWORDB appears
on the TV screen. In such a case, press ENTER. The disc will
stop. Then play back the disc again, and try the procedure
again from step 1.
NOTE:
If you forget your password, enter A8888B in step 3.
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Left+
DVM70S_06DVD Operation.fm Page 34 Thursday, June 2, 2005 6:08 PM
34
EN
BASIC OPERATIONS ON DVD DECK
7
Basic Recording
Press o twice to stop recording.
● It takes about 10 seconds to end the writing session when you
stop recording.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
It is not possible to record programs on a DVD-R disc which has
already been finalized.
DV/HDD/DVD REC MODE
o
CH +/-
I WR
CABLE/DBS
TV
DVD
DVD
0-9
NOTES:
● It is recommended to format a DVD-RAM disc before use if you
use the disc on this unit for the first time.
● When using a brand-new DVD-RW disc, format the disc either in
VR mode or in Video mode. (A pg. 74)
● Recordings made on DVD-R/RW disc must be finalized to play
back on other DVD players. Perform AFinalize A Disc (DVD Deck
Only)B (A pg. 75).
● You can record up to 99 programs and 99 play lists on each disc.
● Some programs can only be recorded one time.
● When recording is started, an index of the first part of recording is
automatically recorded (A pg. 50). To delete the index, refer to
page 52.
● Recording sometimes may stop or cannot be performed even if
there is enough available capacity remaining on the disc.
● It is not possible to record on both DVD and HDD simultaneously.
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the AbpsB unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
The recording modes for a 4.7 GB disc are set as follows:
Recording mode
Recording amount
(approx.)
XP
10 Mbps
1 hour
SP
5 Mbps
2 hours
CH +/-
ENTER
R
o
REC MODE
W
1
Load a recordable disc.
2
Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
3
Press CH +/- or the number keys to select the channel you
wish to record.
● For details, refer to APlacing A DiscB (A pg. 10).
4
Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes
as follows:
XP N SP N LP NEP N FR (60-360*, 420, 480)
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5-minutes interval by
pressing D E repeatedly after selecting AFR60–FR360B. To change the
value in 30-minutes interval, press and hold D E.
● For details on the recording mode, see the right column.
5
Press R on the unit to start recording. Or while holding R, press
I on the remote control.
● The DVD recording lamp lights up on the unit.
6
Press R and W on the remote control simultaneously to pause
recording.
● To resume recording, press R and I simultaneously.
Page 34Thursday, 2 June 2005 18:07
LP
2.5 Mbps
4 hours
EP
1.6 Mbps
6 hours
60-360
(A pg. 36)
I
FR
Maximum recording
time (approx.)
420
480
The amount varies
depending on the
selected time.
1 – 6 hours
7 hours
8 hours
● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36)
Filename [DVM70S_06DVD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 35 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DVD DECK
EN
35
Instant Timer Recording (ITR)
Recording Features
This easy method lets you record for 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or DVD on the
1
2
Press R on the unit to start recording.
3
If you want to record for more than 30 minutes, press R to
extend the time. Each press extends recording time by 30
minutes.
Press R again to engage the ITR mode.
● On the front display panel, A0:30B appears.
remote so that the DVD lamp lights up on the unit.
NOTES:
● You can only perform ITR using the R button on the unit.
● When the recording capacity becomes full during timer recording
or Instant Timer Recording, the unit automatically performs
ARelief RecordingB (A pg. 48).
DV/HDD/DVD
Watch Another Program While Recording On The Unit
R
DISPLAY
CABLE/DBS
TV / VIDEO
REMAIN
Page 35Friday, 6 May 2005 12:06
TV
DVD
While recording is going on, you can watch another program on
the TV. It does not interfere with recording.
1
2
Turn on the TV.
Select the desired channel to watch on the TV using your TV’s
remote control.
DVD
Elapsed Recording Time And Disc Remaining Time
Indication
CH +/-
During recording, press DISPLAY repeatedly until the desired
indication appears on the front display panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time N Disc remaining time N Clock N (Back
to the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of
disc remaining times for all recording modes appears on the TV
screen.
DISPLAY
Filename [DVM70S_06DVD Operation.fm]
DVM70S_00.book Page 36 Friday, May 6, 2005 12:06 PM
36 EN BASIC OPERATIONS ON DVD DECK
Free Rate Function
Second Audio Recording
To record the entire program, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the program to be recorded and either the remaining
disc space or the specified recording time (from 60 minutes to 480
minutes).
8 To record the entire program within the actual remaining
disc space (DVD deck only)
Select AFR (JUST)B in a recording mode selection procedure.
● Note that this function is available only for timer programming
recording (A pg. 46, 48) and dubbing from HDD to DVD
(A pg. 57).
8 To record the entire program by specifying the desired
recording time
Select AFR60–FR360B, AFR420B or AFR480B in a recording mode
selection procedure. (A pg. 34, 37, 46, 48)
8 To record a 25-min. long daily program five times just on
the same DVD disc for example
Perform AVCR Plus+ Timer ProgrammingB (A pg. 46) procedure.
Be sure to set the recording mode to AFR125B and set Weekly/
Daily Rec Function to AMON-FRIB in step 8 to fit the total recording
time to the whole disc space.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: 5th
When the same program is recorded in SP mode instead of in
AFR125B, the 5th program cannot be recorded.
Blank
A: 1st
B: 2nd
C: 3rd
D: 4th
E: Blank (20 min.)
NOTES:
● You can program this unit to timer-record, regardless of the disc
remaining time. When the disc remaining time is not enough, the
unit performs ARelief RecordingB (A pg. 48). To avoid this, make
sure of the disc remaining time before setting timer programming.
(Example) If you programmed to timer-record for 60 minutes in
SP mode on a 120-minute disc, the disc remaining time would be
30 minutes in XP mode, 60 minutes in SP mode, 120 minutes in
LP mode, 180 minutes in EP mode, and 240 minutes in FR480
mode. Timer-recording will not complete beyond these remaining
times.
● The maximum recording time of FR (JUST) mode is the same as
the recording time of FR480 mode. When timer programming a
long program in FR (JUST) mode on a disc whose remaining
time is short, it is recommended to check the disc remaining time
in FR480 mode to see if the remaining time is enough for the
program.
● Even if more than one program are timer programmed in FR
(JUST) mode, only the first one is recorded.
● In order to ensure that the recording fits on the disc, this feature
may leave a slight non-recorded section at the end of the disc.
● There may be some noise and sound disturbance at the point on
the disc where the unit switches the mode.
Page 36Friday, 6 May 2005 12:06
Masterpage:Left+
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set A2ND
AUDIO RECORDB to AONB. (A pg. 72)
NOTES:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
Filename [DVM70S_07HDD Operation.fm]
Masterpage:Right0
DVM70S_07HDD Operation.fm Page 37 Thursday, June 2, 2005 6:10 PM
BASIC OPERATIONS ON HDD DECK
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
ATTENTION:
The HDD on the unit requires approximately 20 seconds to start
up after the unit has been turned on, during which no operation
can be made.
DV/HDD/DVD
CH +/-
Recording Mode
MPEG2 format is used as recording format. As a guide for picture
quality, the AbpsB unit is used to represent how much data can be
recorded per second. The larger this value is, the better the picture
quality becomes but more capacity is required for the recording.
Select XP or SP for programs where quick movement occurs, such
as sports programs, and LP or EP for talk shows, etc. with
relatively less movement.
Recording mode
Maximum recording time (approx.)
XP
34 hours
R
o
CABLE/DBS
TV
DVD
HDD
SP
69 hours
LP
138 hours
EP
209 hours
FR480
300 hours
● For details on FR mode, refer to AFree Rate FunctionB (A pg. 36)
NOTE:
0-9
CH +/-
I
o
R
37
Pause recording on HDD deck
It is not possible to pause recording. Pressing W initiates Live
Memory Playback.
However, it is still possible to pause recording only when recording
the channels of external sources (AL-1B, AF-1B and ADVB). While
holding R, press W on the remote. To resume recording, while
holding R, press I on the remote.
No operation can be made with the buttons on the unit.
Basic Recording
HDD lamp
EN
The maximum recording time stated in the above table are the
approximate time under unused condition.
W
REC MODE
1
Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
2
Press CH +/- or the number keys to select the channel you
wish to record.
3
Press REC MODE repeatedly to select the recording mode,
then press ENTER.
● Each time you press REC MODE, the recording mode changes
as follows:
XP N SP N LP NEP N FR (60-360*, 420, 480)
(Back to the beginning)
* The value is selectable from 1 to 6 hours in 5 minutes interval by
pressing D E repeatedly after selecting AFR60–FR360B. To change the
value in 30 minutes interval, press and hold D E.
● For details on the recording mode, see the right column.
4
Press R on the unit to start recording. Or while holding R, press
I on the remote control.
● The HDD recording lamp lights up on the unit.
5
Press o twice to stop recording.
● Pressing o once displays the confirmation message to stop
recording. Press o again to terminate recording.
NOTES:
● Continuous recording for over 48 hours is not possible.
● It is not possible to record on both DVD and HDD simultaneously.
Page 37
Thursday, 2 June 2005 18:09
Filename [DVM70S_07HDD Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 38 Friday, May 6, 2005 12:06 PM
38
EN
BASIC OPERATIONS ON HDD DECK
Watch Another Program While Recording On The Unit
Recording Features
While recording is going on, you can watch another program on the
TV. It does not interfere with recording.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
HDD lamp
DISPLAY
R
CABLE/DBS
TV
TV / VIDEO
HDD
Turn on the TV.
Select the desired channel to watch on the TV using your TV’s
remote control.
Elapsed Recording Time And Disc Remaining Time
Indication
DV/HDD/DVD
CH +/-
1
2
DVD
During recording, press DISPLAY on the remote control or the unit
repeatedly until the desired indication appears on the front display
panel.
● Each time you press DISPLAY, the time indication changes as
follows:
Elapsed recording time N Disc remaining time N Clock N (Back
to the beginning)
● You can also check the disc remaining time by pressing REMAIN
while the unit is stopped or recording is in progress. The list of
disc remaining times for all recording modes appears on the TV
screen.
Second Audio Recording
CH +/-
REMAIN
DISPLAY
This unit’s built-in MTS decoder enables reception of Multichannel
TV Sound broadcast. To record a SAP program received, set A2ND
AUDIO RECORDB to AONB. (A pg. 72)
NOTES:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
Instant Timer Recording (ITR)
This easy method lets you record for 30 minutes to 6 hours
(selectable in 30-minutes interval), and shuts the unit off after
recording is finished.
1
2
Press R on the unit to start recording.
3
If you want to record for more than 30 minutes, press R to
extend the time. Each press extends recording time by 30
minutes.
Press R again to engage the ITR mode.
● On the front display panel, A0:30B appears.
NOTES:
● You can only perform ITR using the R button on the unit.
● When the recording capacity becomes full during timer recording
or Instant Timer Recording, the unit is automatically shut off.
Page 38
Friday, 6 May 2005 12:06
Filename [DVM70S_07HDD Operation.fm]
Masterpage:Right+
DVM70S_00.book Page 39 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON HDD DECK
Basic Playback
EN
39
Playback Features
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD so that the HDD lamp lights up on the unit.
DV/HDD/DVD
CABLE/DBS
TV
DVD
HDD
o
I W
MARK
CABLE/DBS
TV
DVD
HDD
I
S
O/SLOW -
T
N/SLOW +
W
o
JUMP JUMP +
ENTER
v
w
ON SCREEN
I
o
W
Variable Speed Search
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
Reverse O
N Forward
ATTENTION:
● It may take a few seconds to start playback. This is not a
malfunction.
● Forward/reverse high-speed search and other operations
cannot be performed while playback is stopped.
1
Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
2
Press I to start playback.
● The Library Database Navigation also enables you to search
and select the desired programs. (A pg. 51)
3
Press W to pause playback.
4
Press o to stop playback.
● To resume normal playback, press I.
NOTE:
When the Library Database Navigation screen appears, choose a
thumbnail image of the desired title on the TV screen, then press
ENTER. (A pg. 51)
Reverse
Reverse Search Reverse
Slow Motion Slow Motion Normal
4 steps
Play
Play
3 steps
3 steps
-60 -15 -5 -3
-1
-½ -¼ -116 116
¼ ½
1
Forward Search
5 steps
1.5
3
5
15 60
NOTE:
You can hear the (normal) audio track only during 1.5x speed
search.
Still Picture/Frame-By-Frame Playback
1
2
Press W to pause during playback.
Press SLOW – (O) or SLOW + (N) to activate frame-byframe playback.
● Each press of SLOW – (O) or SLOW + (N) advances/
reverses the still picture frame by frame.
● To resume normal playback, press I.
Slow Motion
1
2
Press W to pause during playback.
Press SLOW – (O) or SLOW + (N) for 2 or more seconds.
● Each press of SLOW – (O) or SLOW + (N) increases the
slow motion speed for each direction.
Skip Search
During playback, press v.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
Page 39
Friday, 6 May 2005 12:06
Filename [DVM70S_07HDD Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 40 Friday, May 6, 2005 12:06 PM
40 EN BASIC OPERATIONS ON HDD DECK
Instant Replay
Marking Positions To Play Back Again Later
You can move back the playback position slightly.
Press w on the remote control or INSTANT REPLAY on the unit.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
1.5x Speed Playback
You can play back a title quickly. The sound will also be played
back faster than normal speed during 1.5x speed playback.
1.5x speed playback cannot be performed during recording on
HDD or DVD.
1
2
3
Press O to locate the point to start 1.5x speed playback from.
Press I to resume playback.
Press N once.
● Pressing ON SCREEN displays AX1.5B on the top right corner of
the screen.
NOTE:
When the unit is connected with a digital audio device using an
optional optical cable, set ADIGITAL AUDIO OUTB to APCM ONLYB.
(A pg. 28)
It is possible to mark positions (up to 999 points) where you want to
play back once again later, and start playback from a marked
position. Marking onto the disc when recording is helpful to locate
a start point when you play back the disc later.
To mark positions:
During playback, press MARK at
positions you want to mark.
● AMARKB appears on the TV screen.
You can easily locate the marked
positions using S or T when
you play back the disc.
To delete the marked positions:
While paused, press S or T to
locate a marked position you want to
delete, then press MARK.
● Crossed AMARKB appears on the
TV screen, and the marked position
is deleted.
NOTE:
When a monaural program changes to a stereo program while
recording, a mark signal is automatically recorded.
Jump Search
You can locate a scene ahead or behind the current one by
jumping scenes according to selected time intervals (A pg. 72)
during playback (or Live Memory Playback).
Press JUMP – or JUMP +.
● To advance forward or back, press JUMP – or JUMP +
repeatedly within 5 seconds of each press to continue jump.
● Depending on the time from where you want to start jump search,
the first press of JUMP – or JUMP + will not necessarily lead to a
jump of the selected time interval. The first press will lead to a
jump to the nearest quarter points of an hour (15 min/ 30 min/ 45
min/ 00 min). The subsequent jumps will then be in accordance
to the selected time interval.
● When you cannot advance any further (beginning or end of
program reached), the message AUNABLE TO GO BACK ANY
MOREB appears on the screen and the on-air screen resumes. In
such a case, press S, O or o.
Example:
Playback search when jump interval is set to 15 MIN jumps.
Taking for instance, you want to start jump search 40 minutes after
the beginning of the program. Pressing JUMP – or JUMP + will
result in a jump to the scene at the 30 minutes point or 45 minutes
point respectively as illustrated below. At the subsequent press, the
scene will jump to the 15 minutes point or 1 hour point respectively,
according to the selected time interval, which in this case is A15
MINB.
Time counter
0 min
15 min
Beginning of program
Page 40
30 min
40 min
45 min
Current scene
1 h 15 min
1h
End of program
Friday, 6 May 2005 12:06
Filename [DVM70S_08DV Operation.fm]
Masterpage:Right0
DVM70S_00.book Page 41 Friday, May 6, 2005 12:06 PM
BASIC OPERATIONS ON DV DECK
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
DV/HDD/DVD
I
o O N
M
CABLE/DBS
TV
Load a cassette. Make sure the window side is up, the rear
label side is facing you and the arrow on the front of the
cassette is pointed toward the unit.
● Do not apply too much pressure when inserting.
● If the erase protection switch is set to ASAVEB, playback begins
automatically. It takes about 15 seconds until the playback
picture appears. However, when APOWER SAVEB is set to
AONB (A pg. 72), playback will not begin automatically even
though a cassette with its erase protection switch set to ASAVEB
is inserted.
● The unit’s power comes on automatically.
2
Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
3
Find the program start point. If the tape is advanced past the
start point, press O. To go forward, press N.
4
5
Press I to start playback.
Press o to stop playback.
● To eject the cassette, press M (DV).
DVD
Clean the video heads using a dry cleaning cassette
- M-DV12CL - when:
● No picture during playback.
● Block noise appears during playback.
● AUSE CLEANING CASSETTEB appears on the screen.
DV
o
o
41
1
Basic Playback
O
EN
N
NOTE:
The heads get dirty in the following cases:
● in an environment prone to extreme temperature or humidity
● in a dusty environment
● flaw, dirt or mould on video tapes
● continuous usage for a long time
Usable cassettes
● Cassettes marked P can be used with the DV deck.
● Tapes recorded in the DVCAM format can be played.
NOTE:
When you record a tape on the DV deck with the recording speed
set to ALPB, it is recommended to play back that tape back on this
DV deck. Digital video recorder from other manufacturers may not
be able to play back the tape properly.
Accidental erasure prevention
To prevent accidental recording on a recorded cassette, set its
erase protection switch to ASAVEB. To record on it later, set the
switch to ARECB.
Erase protection switch
Page 41Friday, 6 May 2005 12:06
Filename [DVM70S_08DV Operation.fm]
Masterpage:Left+
DVM70S_00.book Page 42 Friday, May 6, 2005 12:06 PM
42
EN
BASIC OPERATIONS ON DV DECK
Skip Search
Playback Features
During playback, press v.
● Each press initiates an approximately 30-second period of fastmotion playback. Normal playback resumes automatically.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly or DV on the
Instant Replay
During playback, press w on the remote control or
INSTANT REPLAY on the unit. The unit rewinds the picture a little
(about 7 seconds) and resumes playback.
remote so that the DV lamp lights up on the unit.
Next Function Memory
CABLE/DBS
TV
DV
DVD
The Next Function Memory AtellsB the unit what to do after rewinding.
Before continuing, make sure the unit is in the Stop mode.
1
For Automatic Start Of Playback
Press O, then press I within 2 seconds.
Soundtrack Selection
Your unit is capable of recording two soundtracks (L and R) and
will play back the one you select.
During Playback
Pressing AUDIO changes the soundtrack as follows:
TRACK
I
N
W
O
On-Screen Display
L+R
Both sounds on the left channel and
the right channel are mixed and
played back
L
Sound on the left channel is played
back
R
Sound on the right channel is played
back
DISPLAY
AUDIO
Time Code
ATTENTION:
In the search, still, slow-motion or frame-by-frame playback
mode, a slight mosaic effect appears on screen.
During recording, a time code is recorded on the tape. This time
code is used to confirm the position on the tape when playing back
or editing a tape.
Variable Speed Search
1
During playback, press N for forward variable speed search, or
O for reverse variable speed search.
● Each press of the button increases the search speed for each
direction.
● To resume normal playback, press I.
Reverse O
Reverse Search
3 steps
-12
-4
-2
N Forward
Reverse
Slow Motion Slow Motion
1 step
1 step
-1 5
Normal Play
15
1
Forward Search
3 steps
2
4
12
Still Picture/Frame-By-Frame Playback
1
2
Press W to pause during playback.
Press W to activate frame-by-frame playback.
● To resume normal playback, press I.
Slow Motion
1
2
Press W to pause during playback.
Press and hold W for 2 seconds, then release. Press W and
release again to return to still picture.
● Press N for forward slow motion or O for reverse slow
motion.
● To resume normal playback, press I.
Page 42Friday, 6 May 2005 12:06
USE
Press DISPLAY on the remote control or the unit until the time
code on the tape appears on the front display panel and the TV
screen.
● Each time you press DISPLAY, the indication changes as
follows:
Tape remaining time N Time code N Clock time N (Back to
the beginning)
Filename [DVM70S_09Live Memory.fm]
DVM70S_00.book Page 43 Friday, May 6, 2005 12:06 PM
Masterpage:Right0
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
EN
43
Recording/playback Status Display
Live Memory Playback
CABLE/DBS
TV
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DV/HDD/DVD on the unit repeatedly to select the HDD
or DVD deck.
This unit records pictures onto the hard disc and DVD-RAM disc,
instead of video tapes, then plays back the pictures recorded on
the disc. This makes it possible to achieve high-speed writing and
read-out that has not been possible with conventional VCRs,
enabling recording and playback simultaneously.
High-speed spin
Recording
(High-speed writing)
Playback
(High-speed read-out)
It is called ALive Memory PlaybackB to start playback of the
program being recorded, with a time-lag between a recording point
and a playback point, as shown in the figure below.
Current playback point
(Live Memory Playback)
Recording start point
Current recording position
(Recording point)
Recording
continues
Playback
continues
0
30 min.
Currently elapsed recording time
1 hour
Not only can this unit play back a program previously recorded
while recording or timer recording another program, but the unit
also allows you to play back from the beginning of a program while
continuing to record the same program.
Page 43Friday, 6 May 2005 12:06
DVD
LIVE
NAVIGATION
Press NAVIGATION to display Library Database
Navigation menu, then choose a program to
play back. (A pg. 50)
o
ON SCREEN
Live Memory Playback status can be checked by
pressing ON SCREEN to display the bar meter on
the superimpose display. The current status is
superimposed on the TV screen. (A pg. 16, AWhen
using Live Memory playbackB)
NOTES:
● Live Memory Playback could be performed approximately 30
seconds after recording has started on the DVD-RAM disc.
However, for HDD, Live Memory Playback is possible right after
recording has started.
● Although high-speed search up to approximately 30 seconds
before the current recording point is possible during Live Memory
Playback, once the current recording point is reached, the unit
resumes normal playback and maintains a delay of
approximately 30 seconds so that recording and playback can
continue.
● When using Live Memory Playback during timer recording,
playback continues even after the end of the recording.
● When using Live Memory Playback during timer recording,
playback is automatically stopped just before recording starts,
and then recording starts when the time arrives for the next timerprogram.
● It is impossible to perform ITR even if you press R during Live
Memory Playback. (A pg. 38)
Press o to display the program being recorded, then perform ITR
settings.
● Playback may be paused for a moment during Live Memory
Playback, which does not interfere with recording.
● Live Memory Playback cannot be performed while recording the
source from DV input. (A pg. 60, ADV Dubbing (HDD & DVD
Deck Only)B)
● When LIVE CHECK is pressed to display the picture currently
being recorded, the picture size may not be correct.
● Press R or LIVE to stop Live Memory Playback.
● Live Memory Playback cannot be performed even if the ALIVE
MEMORYB in AHDD SET UPB is set to other than AOFFB, as
temporary recording on HDD stops during recording on DVD.
Filename [DVM70S_09Live Memory.fm]
DVM70S_00.book Page 44 Friday, May 6, 2005 12:06 PM
44 EN LIVE MEMORY PLAYBACK ON HDD/DVD DECK
Buttons To Be Used During Live Memory Playback
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to select the desired deck for Live Memory
Playback.
CABLE/DBS
TV
HDD
DVD
DVD
A
B
C
D
E
G
F
I
J
H
K
L
M
A LIVE
Returns to on air program screen. When a confirmation
message appears by pressing this button during timer
programming or title editing, etc., follow the instruction to return
to the previous screen.
B NAVIGATION
Displays Library Database Navigation menu. You can choose a
title to play back.
C S
● Pressing once skips back to the beginning of the chapter being
played back.
● Pressing down for 2 or more seconds during playback reverses
playback at 5 times the normal speed while pressed. Releasing
the button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed.
D T
● Pressing once skips forward to the beginning of the next
chapter being played back.
● Pressing down for 2 or more seconds during playback
advances playback at 5 times the normal speed while pressed.
Releasing the button resumes normal playback.
Available only when paused
● Pressing down for 2 or more seconds advances playback at 1/
16 times the normal speed.
E O
● Each press of the button during playback advances the
playback speed in 5 steps in the reverse direction.
Available only when paused
● Each press of the button reverses the still picture frame by
frame.
● Pressing down for 2 or more seconds reverses playback at 1/16
times the normal speed. Then, each press of the button
reverses slow-motion at 1/16 times, 1/4 times and 1/2 times the
normal playback.
Page 44Friday, 6 May 2005 12:06
Masterpage:Left+
F N
● Each press of the button during playback advances the
playback speed in 4 steps in the forward direction.
Available only when paused
● Each press of the button advances the still picture frame by
frame.
● Pressing down for 2 or more seconds advances playback at 1/
16 times the normal speed. Then, each press of the button
advances slow-motion at 1/16 times, 1/4 times and 1/2 times
the normal playback.
G o
● Pressing once during Live Memory Playback or RetroActive
Recording returns to the screen on air.
● Pressing twice during recording stops recording and returns to
the screen on air.
H W
● Pressing once pauses playback (still picture playback).
● Pressing repeatedly advances the still picture frame by frame.
I JUMP –
Each press of the button during Live Memory Playback jumps
back for the selected time interval and resumes playback.
(A pg. 40, AJump SearchB)
J JUMP +
Each press of the button during Live Memory Playback jumps
forward for the selected time interval and resumes playback.
(A pg. 40, AJump SearchB)
K v
It is useful when skipping over unwanted sections.
● Pressing once skips forward for approximately 30 seconds and
resumes playback.
● Pressing repeatedly skips forward continuously as many times
as pressed.
L w
It is useful when watching sports programs, etc.
● Each press skips back for approximately 7 seconds and
resumes playback.
● Pressing repeatedly skips back for approximately 7 seconds
continuously as many times as pressed.
M LIVE CHECK
You can check, for example, if the program you are recording
has already finished.
● Pressing once displays the picture currently being recorded and
the one being played back simultaneously.
● Pressing successively clears the Live Check window and
displays only the picture currently being played back.
Filename [DVM70S_09Live Memory.fm]
Masterpage:Right+
DVM70S_00.book Page 45 Friday, May 6, 2005 12:06 PM
LIVE MEMORY PLAYBACK ON HDD/DVD DECK
EN
45
Temporary recording for Live Memory (HDD deck only)
Simultaneous Recording and Playback
This unit automatically records the channel being received, within
the specified range of time, to the reserved space on the hard disc.
The time range can be set for 30 minutes, 1 hour, and 3 hours.
(A pg. 71)
You can play back the previous part of the channel you are
recording or other programs available in the Library Database.
1
Press NAVIGATION. The Library Database Navigation screen
appears.
NOTE:
Previous temporary recordings will be overwritten since the unit is
always recording the channel being received. Thus, it is not
possible to play back TV programs recorded beyond the specified
range of time since they are already overwritten. To avoid this in
order to save titles, perform normal recording (A pg. 37), timer
recording (A pg. 46, 48), or RetroActive Recording (A pg. 45).
2
3
Press D E to select AORIGINALB, then press ENTER.
About limitation on temporary recording
The temporary recording for Live Memory is canceled in the
following cases, and will start all over again when it is to resume.
● When the power is turned off
● When the system is powered again after a power failure was
occurred
● When normal recording, timer recording or RetroActive
Recording is performed
● When the ALIVE MEMORYB setting is changed (A pg. 71)
● When tuner channel setting is performed (A pg. 22)
● When dubbing is performed by pressing DUBBING (A pg. 57)
● When ADVB is selected by pressing CH +/- (A pg. 60)
RetroActive Recording (HDD deck only)
You can start recording from the previous part of the channel you
are currently watching (temporarily recorded on the background).
(A pg. 45, ATemporary recording for Live Memory (HDD deck
only)B)
1
Press S or O to locate the point to start recording from.
2
Press R on the unit to start RetroActive Recording. Or while
holding R, press I on the remote control.
3
Press o to stop RetroActive Recording.
● Each press of O increases the reverse search speed.
● The on-air screen resumes.
NOTES:
● You cannot use RetroActive Recording for channels other than
the channel you are currently watching.
● Recording speed is automatically set to FR65 mode when
RetroActive Recording is started.
● Temporarily recorded data prior to the beginning of RetroActive
Recording is erased when RetroActive Recording started.
Press FGD E to select the desired title, then press ENTER.
● For DVD-RAM, playback starts from the beginning of the title if
ACONTINUOUS PLAYB in ADVD SET UPB is set to AONB
(A pg. 71).
4
Press D E to select the desired playback method
(ABEGINNINGB, ARESUMEB or AREPEATB), then press ENTER.
● Playback of the selected title begins automatically.
5
Press o to stop playback.
● The on-air screen resumes.
NOTES:
● You can use various playback features during Live Memory
Playback.
● To stop simultaneous playback, press o. The on-air screen
resumes. To stop actual recording, press o again.
Instant Replay
You can move back the playback position slightly during recording
or Live Memory Playback.
Press w on the remote control or INSTANT REPLAY on the unit.
8 DVD-RAM
● Pressing once during recording skips back for approximately 30
seconds and starts Live Memory Playback. While pressing once
during Live Memory Playback skips back for approximately 7
seconds and resumes playback.
● Each subsequent press skips back for approximately 7 seconds
and resumes playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
8 HDD
● Pressing during recording skips back for approximately 7
seconds and starts Live Memory Playback. While pressing during
Live Memory Playback skips back for approximately 7 seconds
and resumes playback.
● Each press skips back for approximately 7 seconds and resumes
playback.
● Pressing while paused skips back for approximately 7 seconds
and resumes pause.
Resuming Playback (HDD deck only)
You can resume playback of a TV broadcast you were recording or
watching from the point you have paused.
1
Press W to pause a TV broadcast.
2
Press I to start Live Memory Playback.
3
Press o to resume the on-air screen.
● Recording continues when recording.
● Playback resumes from the paused position.
Page 45Friday, 6 May 2005 12:06
Filename [DVM70S_10Timer Recording.fm]
Masterpage:Left0
DVM70S_00.book Page 46 Friday, May 6, 2005 12:06 PM
46
EN
TIMER RECORDING ON HDD/DVD DECK
7
VCR Plus+ Timer Programming
You can program this unit to timer record as many as 16 programs.
With the VCR Plus+ system, timer programming is greatly
simplified because each TV program has a corresponding code
number which your unit is able to recognize.
You can use the remote control to enter the PlusCode number.
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
IMPORTANT:
Make sure the channel position number you wish to record is
displayed; if not, see AChanging VCR Plus+ SettingB (A pg. 73)
and set the Guide Channel number correctly.
8
Press F G to select the desired recording option as required.
Press F G to select the desired setting, then press ENTER.
● AINPUT NAMEB (A pg. 51, AModify Title NameB)
● ACATEGORYB (A pg. 52, AModify CategoryB)
● AWEEKLY/DAILYB (A pg. 47, AWeekly/Daily RecordingB)
● AREC MODEB (A pg. 34, ARecording ModeB)
CABLE/DBS
TV
The PlusCode number you entered and the matching timerrecording information are displayed on the TV screen. Check
the program data.
● To cancel this setting, press RETURN.
DVD
9
Press F G to select AOKB, then press ENTER to access the
Program Confirmation screen.
10 Press D E to select AEXITB, then press ENTER to complete
0–9
timer programming.
● To program another timer, press D E to select ACONTINUEB,
then press ENTER.
PROG
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
ENTER
FGDE
NOTES:
RETURN
● There may be cases that the VCR Plus+ Timer Programming
function prolongs the stop time of the programming.
● When two successive programs are recorded on a DVD-RW disc
with the VCR Plus+ Timer Programming function, the beginning
of the second one may be left off the recording.
● If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
DISPLAY
1
2
3
Load a recordable disc if recording to DVD.
Press PROG to access the program top screen.
Press FGD E to select AVCR Plus+ PR.B, then press ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
4
Press the number keys to
enter the PlusCode number of
a program you wish to record.
1234
OR
1 2 3
4 5 6
Press FGD E to select the
7 8 9
desired number key on the
0
screen, then press ENTER.
Repeat to enter all required
numbers.
● If you have made a mistake, press FGD E to select ADELETEB
or ADELETE ALLB, then press ENTER and input the correct
number before you press ENTER again.
123 PROGRAM > VCR Plus+ PR. (1/2)
PLUS CODE NO.
SELECT WITH @
THEN PRESS [ENTER]
PRESS [PROG] TO EXIT
DELETE
PROG
ENTER
EXIT
SELECT
RECORD TO
DELETE ALL
DVD
CONFIRM
5
Press F G to select ARECORD TOB, then press ENTER. Press
F G to select the desired recording deck, then press ENTER.
6
Press FGD E to select ACONFIRMB, then press ENTER.
● If the number you entered is invalid, APLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRYB appears on the TV
screen. Input a valid PlusCode number.
● If AGUIDE PROGRAM IS NOT SET SET GUIDE PROGRAM
THEN RETRYB appears on the TV screen, set Guide Channel
Numbers manually. (A pg. 73)
Page 46Friday, 6 May 2005 12:06
IMPORTANT:
If you have moved to a different area or if a broadcasting
station’s channel number has been changed, the wrong channel
number will be displayed on the VCR Plus+ program screen in
step 7. When this happens, set the correct Guide Channel
number for that station. (A pg. 73, AChanging VCR Plus+
SettingB)
Cable Box and DBS Receiver Users
To timer record a satellite broadcast using the VCR Plus+
system:
A Perform AVCR Plus+ Timer ProgrammingB (A pg. 46).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
Filename [DVM70S_10Timer Recording.fm]
Masterpage:Right+
DVM70S_00.book Page 47 Friday, May 6, 2005 12:06 PM
TIMER RECORDING ON HDD/DVD DECK
Weekly/Daily Recording
You can record programs with one of the following weekly/daily
timer settings.
For the HDD deck
When you select a mode other than ONCE, the space on the hard
disk drive is saved for new recordings by overwriting previous
recordings. To prevent loss of a needed recording, backup
programs you wish to save by dubbing them to DVD discs before
overwriting previous recordings. Or save the title of weekly/daily
programs to avoid overwriting of a previous week/day. (A pg. 49)
ONCE (One Time Recording)
In this mode a program will not be automatically overwritten.
WEEKLY (OVERWRITE) (Weekly Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program
recorded last week is automatically deleted and overwritten by
the new program. Save the title of each program you wish to
save, then the recorded program is saved and will not be
overwritten by the new program.
This week’s drama
Overwritten
Last week’s drama
MON-SUN (FOR A WEEK)/ MON-SAT (FOR A WEEK)/
MON-FRI (FOR A WEEK) (Daily Recording/Weekly Overwrite)
When the set weekly program is broadcast, the program
recorded on the same day last week is automatically deleted
and overwritten by the new program. Save the title of each
program you wish to save, then the recorded program is saved
and will not be overwritten by the new program.
Overwritten
This
week
MON TUE
WED THU
FRI
Last
week
MON TUE
WED THU
FRI
MON-SUN (OVERWRITE)/ MON-SAT (OVERWRITE)/
MON-FRI (OVERWRITE) (Daily Recording/Daily Overwrite)
When the set daily program is broadcast, yesterday’s program
is automatically deleted and overwritten by the new program.
Save the title of each program you wish to save, then the
recorded program is saved and will not be overwritten by the
new program.
Tuesday’s program
Overwritten
Monday’s program
For the DVD deck
ONCE (One Time Recording)
WEEKLY (Weekly Recording)
MON-SUN/ MON-SAT/ MON-FRI (Daily Recording)
Page 47Friday, 6 May 2005 12:06
EN
47
Filename [DVM70S_10Timer Recording.fm]
Masterpage:Left+
DVM70S_00.book Page 48 Friday, May 6, 2005 12:06 PM
48
EN
TIMER RECORDING ON HDD/DVD DECK
Manual Timer Programming
You can program this unit to timer record as many as 16 programs.
If you do not know the PlusCode number for the program you wish
to record, use the following procedure to set your unit to
timer record the program.
Press F G to select ASOURCEB, then press ENTER. Press F G
to select the desired source.
9
Press F G to select ACHB, then press ENTER. Press F G to
select the desired channel.
10 Press F G to select ACONFIRMB, then press ENTER.
11 Set the other recording options as required.
● Refer to step 8 in AVCR Plus+ Timer ProgrammingB
● Make sure that the unit’s built-in clock is set properly.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
(A pg. 46).
12 Press F G to select AOKB,
then press ENTER to access
the Program Confirmation
screen.
13 Press D E to select AEXITB,
CABLE/DBS
TV
8
DVD
2
PROGRAM > CALENDAR PR. (3/3)
01/08/03 WED 10:30PM - 11:00PM
DBS 100
GARDENING
[EDUCATION] FR360
1:00
SELECT WITH @
THEN PRESS [ENTER]
28:00
INPUT NAME
GARDENING
CATEGORY
EDUCATION
PRESS [PROG] TO EXIT
WEEKLY/DAILY
MON-FRI (FOR A WEEK)
then press ENTER to
complete timer
programming.
● To program another timer,
press D E to select ACONTINUEB, then press ENTER.
● If APROGRAM OVERLAPPEDB appears on the TV screen,
delete or modify the programs.
REC MODE
PROG
ENTER
EXIT
SELECT
FR360
OK
PROG
ENTER
NOTES:
● When two successive programs are recorded on a DVD-RW disc
with Manual Timer Programming function, the beginning of the
second one may be left off the recording.
● If the copy limited program is received during timer-recording, the
unit enters Record Pause mode. Recording starts again if it is
switched to a recordable broadcast during the time you
programmed.
FGDE
Cable box and DBS Receiver Users
To timer record a satellite broadcast using Manual Timer
Programming:
A Perform AManual Timer ProgrammingB (A pg. 48).
B Set the cable box or DBS receiver to the appropriate channel
before the selected program begins.
C Leave the cable box or DBS receiver’s power on.
1
2
3
Load a recordable disc if recording to DVD.
4
5
Press FGD E to select the desired date, then press ENTER.
Press PROG to access the program top screen.
Press FGD E to select ACALENDAR PR.B, then press ENTER.
● When APROGRAM FULL DELETE UNWANTED TIMER
PROGRAMSB appears on the TV screen, you need to cancel
some of the reserved programs. (A pg. 49)
Press F G to select ARECORD
TOB, then press ENTER. Press
F G to select the desired
recording deck, then press
ENTER.
2
PROGRAM > CALENDAR PR. (2/3)
01/08/03 WED 10:30PM - 11:00PM DBS 100
[MISC. ] XP
SELECT WITH @
THEN PRESS [ENTER]
HDD
RECORD TO
START
10:30PM
STOP
11:00PM
PRESS [PROG] TO EXIT
6
Press F G to select ASTARTB,
then press ENTER. Press F G
to set the desired start time,
then press ENTER.
● Each press of F G increases/decreases the start time in 1minute interval.
● To increase/decrease the start time in 30-minutes interval,
press and hold F G.
CATV
SOURCE
100
CH
PROG
ENTER
EXIT
SELECT
CONFIRM
7
Press F G to select ASTOPB, then press ENTER. Press F G to
set the desired stop time, then press ENTER.
● Each press of F G increases/decreases the stop time in 1minute interval.
● To increase/decrease the stop time in 30-minutes interval,
press and hold F G.
Page 48Friday, 6 May 2005 12:06
Relief Recording
When a program that is set for the DVD deck cannot be
recorded properly, the program is recorded to the HDD deck
instead in XP mode.
● If the remaining capacity of the hard disc is not sufficient, the
program is recorded to the DVD deck until the remaining
capacity of the DVD disc lasts.
● If AJUSTB is selected for the recording mode, the current
recording mode for the DVD deck is applied.
Filename [DVM70S_10Timer Recording.fm]
Masterpage:Right+
DVM70S_00.book Page 49 Friday, May 6, 2005 12:06 PM
TIMER RECORDING ON HDD/DVD DECK
CABLE/DBS
TV
DVD
EN
49
Check Programs
To check the whole list of programs
1
2
Press PROG to access the program top screen.
Press FGD E to select APROGRAM LISTB, then press ENTER.
● The details of a selected program appear on the top of the
screen.
● The daily program of a title is listed as one program.
PROG
ENTER
FGDE
To check the list of programs by date
1
2
3
Press PROG to access the program top screen.
Press FGD E to select ACALENDAR LISTB, then press ENTER.
Press F G to select the desired date, then press ENTER.
Cancel And Change Programs
● Repeat steps in ACheck ProgramsB to select a program before
proceeding.
To cancel the program
1
Press FGD E to select ACANCELB, then press ENTER.
To modify the program settings
1
2
Press FGD E to select AMODIFYB, then press ENTER.
Change the settings of the desired recording options as
required.
● Refer to steps 4 – 13 in AManual Timer ProgrammingB
(A pg. 48).
To skip the weekly/daily programs to the next week/day
It is easy to temporarily cancel weekly/daily programs of a week/
day.
1
2
Press FGD E to select APROGRAM SKIPB, then press ENTER.
Press D E to select ASKIPB, then press ENTER.
To save the titles of weekly/daily programs (HDD Deck Only)
Use this function to avoid overwriting titles of weekly/daily
programs of a previous week/day.
1
2
Press FGD E to select ATITLE SAVEB, then press ENTER.
Press D E to select ASAVEB, then press ENTER.
NOTE:
This function is available only when the remaining capacity of the
hard disc is sufficient.
Page 49Friday, 6 May 2005 12:06
Filename [DVM70S_11Navigation.fm]
DVM70S_00.book Page 50 Friday, May 6, 2005 12:06 PM
50
EN
NAVIGATION ON HDD/DVD DECK
Using Library Database Navigation system, you can easily modify
registered information, edit the title or play list, as well as search
for the beginning of each title.
Library Database Navigation
The Library Database Navigation enables you to search and select
the desired titles recorded on the HDD deck and the DVD deck
very easily.
You can record up to 99 titles on a disc.
Each time a title is recorded, the information of the title is
registered for the Library Database Navigation automatically.
So, you can confirm the information of the titles recorded with the
Library Database Navigation screen. And, you can also select one
of the titles recorded using the Library Database Navigation.
The following screen appears as the Library Database Navigation
screen when you press NAVIGATION. You can move the arrow to
select the desired position on the screen by pressing FGD E on
the remote control.
NAVIGATION > ORIGINAL
A
0026 [FISH WORLD
]
25/12/03 THU 10:00AM - 10:15AM
FROG WORLD
143 MIN
PR. 3
[HOBBY] EP
D
SELECT WITH @
THEN PRESS [ENTER]
B
C
PRESS [NAVIGATION]
TO EXIT
NAVIGATION
ENTER
EXIT
SELECT
E
F
G
A Playback screen
(Indicates currently received TV program.)
B Guidance for operations
C Scroll bar
(Appears when there are over nine registered titles (or play
lists). The scroll bar only indicates that there are more titles (or
play lists) hidden off the current screen display. To show hidden
titles (or play lists), press FGD E repeatedly.)
D Recording information for the title indicated by the arrow
E Index list
(Thumbnail still of each title)
Thumbnail still is not to be played back.
F Index
:Indicates no index is registered.
:Indicates title in standby for timer recording.
:Indicates no title is registered.
G Icons
(Indicate the record condition of each title.)
The Icons and their meanings
This title is write-protected.
This title was recorded with timer recording.
W
This title is Weekly Recording/Weekly Overwrite.
D
This title is Daily Recording/Daily Overwrite.
D
NEW
Masterpage:Left0
This title is Daily Recording/Weekly Overwrite.
This title has not been played back.
This title is copy-protected.
This title can only be recorded once (copy-once title).
Page 50Friday, 6 May 2005 12:06
About registration of information
The following information is automatically registered for each title
when ordinary recording or timer recording is performed, then
stored in an area specified on the unit.
● index* (reduced pictures to show program titles)
● program title*
● category*
● date and time
● channel
● recording mode
● length of recording time
The items marked with an asterisk (*) can be easily modified and
registered again after recording by using Library Database
Navigation system.
The limitations of registration
You can register information up to 99 titles for the DVD deck and
200 titles for the HDD deck.
When the amount of information is at the limits of registration, you
cannot record new titles any more. In this case, you need to delete
old titles to register new one. (A pg. 52)
NOTES:
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● When you move the title recorded on HDD to DVD, the icon will
be changed to
.
● Sound of received channel may be interrupted while the Library
Database Navigation screen is displayed.
● The order of index which are displayed by pressing DUBBING
differs from the images displayed by pressing NAVIGATION or
EDIT.
● You cannot perform timer recording during editing of thumbnail
images or play lists by pressing EDIT. Press EDIT to clear the
Editing screen before performing timer recording.
Filename [DVM70S_11Navigation.fm]
Masterpage:Right+
DVM70S_00.book Page 51 Friday, May 6, 2005 12:06 PM
NAVIGATION ON HDD/DVD DECK
Scan For Beginning Of Title
Edit Original Information
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to scan.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
CABLE/DBS
TV
HDD
CANCEL
ENTER
o
DVD
DVD
ATTENTION:
● It is not possible to modify discs recorded on DVD units from
other manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
MEMO
NAVIGATION
FGDE
Modify Index
I
1
2
W
3
2
3
Press FGD E to select AORIGINALB, then press ENTER.
Press FGD E to select the
index (small pictures) of the
desired title, then press
ENTER.
● When you want the plural titles
to be played back
continuously, press MEMO
after selecting the desired title.
The numbers of the playback
order appear on the index. You can select up to 8 titles.
● When you want to correct the order, move the arrow to the
desired index and press MEMO. The number disappears and
the unit re-numbers the other programs automatically.
● When you want to cancel the order, press CANCEL(L).
NAVIGATION > ORIGINAL
0026 [FISH WORLD
]
143 MIN
TV 3
[HOBBY] EP
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
NAVIGATION
ENTER
EXIT
SELECT
4
Press D E to select
ABEGINNINGB, then press
ENTER.
● To resume playback from the
point where playback was
previously stopped, press D E
to select ARESUMEB, then
press ENTER.
● To repeat playback of a
selected title, press D E to select AREPEATB, then press
ENTER.
NAVIGATION > ORIGINAL
25/12/03 THU
10:00AM - 10:15AM TV
FROG WORLD
3
SELECT HOW TO PLAY BACK
Press W to pause playback.
6
Press o to stop playback.
NAVIGATION
ENTER
EXIT
SELECT
● To resume normal playback, press I.
Page 51Friday, 6 May 2005 12:06
BEGINNING
RESUME
SP
[HOBBY]
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
Press FGD E to select AMODIFYB under AORIGINALB, then
press ENTER.
4
Press FGD E to select one title you want to modify, then press
ENTER.
5
6
Press D E to select AINDEXB, then press ENTER.
TV 3
25/12/03 THU 10:00AM - 10:15AM
Press NAVIGATION. The Library Database Navigation screen
appears.
25/12/03 THU 10:00AM - 10:15AM
(DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
EDITING > MODIFY INDEX
1
FROG WORLD
Press EDIT. The Editing screen appears.
Press I to start playback. Press O or N to search for the
picture from the title, then press W.
● The pictures of the title appear
on the left window.
You can scan the beginning of the title easily with the Library
Database Navigation.
5
51
EN
REPEAT
FROG WORLD
7
Confirm the arrow is on
AREPLACEB, then press
ENTER to register new index.
New index appears on the
right window.
● When you press ENTER with
the arrow on ARETURNB you
can return to the previous screen.
8
[OTHERS] SP
INDEX
PROG. 1
0 : 01 : 03
SELECT IMAGE TO REPLACE WITH
ON REMOTE
REPLACE
RETURN
Press EDIT to return to the normal screen.
Modify Title Name
1
Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
2
3
Press FGD E to select ANAMEB, then press ENTER.
Press FGD E to select the
desired letter or command,
then press ENTER. Repeat
this process to complete the
name.
● To correct a letter, press
FGD E to select ADELETEB,
then press ENTER.
● You can enter the letters up to
64.
4
5
ABC EDITING > MODIFY NAME
0026 [FISH WORLD
]
64 MIN
TV 3
25/12/03 THU 10:00AM - 10:15AM
[HOBBY] XP
FROG WORLD
F R O G WO R L D
SELECT WITH @
THEN PRESS [ENTER]
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
A
B
a
b
G
H
K
L
g
h
i
j
M
N
O
P
Q
R
m
n
o
p
q
r
7
S
T
U
V
W
X
s
t
u
v
w
x
0
+
-
Y
Z
C
y
z
*
/
=
!
"
#
$
;
<
>
?
@
[
|
}
~
'
(
)
,
\
]
^
_
`
{
I
D
J
CANCEL
E
F
% &
.
:
DELETE
Press FGD E to select ASAVEB, then press ENTER.
Press EDIT to return to the normal screen.
c
d
e
k
f
1
2
3
l
4
5
6
8
9
SAVE
Filename [DVM70S_11Navigation.fm]
Masterpage:Left+
DVM70S_00.book Page 52 Friday, May 6, 2005 12:06 PM
52 EN NAVIGATION ON HDD/DVD DECK
Modify Category
Delete Unwanted Part Of The Title
(DVD-RAM & DVD-RW (VR mode) only)
1
Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
2
3
Press FGD E to select ACATEGORYB, then press ENTER.
4
Press FGD E to select the
desired category, then press
ENTER.
Press EDIT to return to the
normal screen.
You can delete unwanted part of the title.
EDITING > MODIFY CATEGORY
0026 [FISH WORLD
]
64 MIN
TV 3
25/12/03 THU 10:00AM - 10:15AM
[HOBBY] XP
FROG WORLD
SELECT WITH @
THEN PRESS [ENTER]
MOVIES
PRESS [EDIT]
TO EXIT
EDIT
ENTER
EXIT
SELECT
MUSIC
DRAMA
ANIMATION
SPORTS
DOCUMENTARY
NEWS
WEATHER
EDUCATION
HOBBY
ENTERTAINMENT
ART
Protect Title (DVD-RAM & DVD-RW (VR mode) only)
1
Perform steps 1 – 2 of AModify IndexB (A pg. 51) before
continuing.
2
3
Press FGD E to select ADEL SCENB, then press ENTER.
4
Press I to start playback. Press O or N to find the point
where you want the deletion to begin, then press W.
5
Confirm the arrow is on AINB,
then press ENTER.
6
Press I to start playback.
Press O or N to find the
point where you want the
deletion to end, then press W.
You can protect titles to prevent accidental erasure of the
important titles.
1
Perform steps 1 – 2 of AModify IndexB (A pg. 51) before
continuing.
2
3
Press FGD E to select APROTECTB, then press ENTER.
Press FGD E to select a title you want to protect, then press
ENTER.
4
Press D E to select APROTECTB, then press ENTER. A
B
appears.
● To cancel the protection, repeat 3 – 4 again. In step 4, select
ACANCEL PROTECTB, then press ENTER.
5
Press EDIT to return to the normal screen.
NOTE:
All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles. (A pg. 52)
Delete Title
You cannot record any more with Library Database Navigation
once the registered titles on the disc reach 99 titles for the DVD
deck and 200 titles for the HDD deck. Deleting unnecessary titles
after dubbing or other operations can increase remaining time and
available recording capacity. (For DVD-R discs, although it is
possible to delete recorded titles, available recording capacity
does not increase.) The deleted title is never resumed. Play lists
and title information in the unit’s library are also deleted.
1
2
3
Press EDIT. The Editing screen appears.
(DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
Press FGD E to select ADELETEB under AORIGINALB, then
press ENTER.
4
Press FGD E to select one title you want to delete, then press
ENTER.
5
Press D E to select ADELETEB, then press ENTER.
6
Press EDIT to return to the normal screen.
● When you cancel the deletion, select ACANCELB, then press
ENTER.
Page 52Friday, 6 May 2005 12:06
Press FGD E to select one title whose unwanted part you want
to delete, then press ENTER.
7
Press D E to select AOUTB,
then press ENTER.
● Select APREVIEWB, then press
ENTER to preview the edited title.
8
EDITING > ORIGINAL/DEL SCENE
21/12/03 SUN 5:30AM - 8:00AM
TV 12
[OTHERS] SP
RALLY CAR
IN
0 : 05 :15
OUT
0 : 06 :15
PROG. 1
0 : 01 : 03
SELECT SCENE TO DELETE WITH
IN
OUT
ON REMOTE
PREVIEW
OK
Press D E to select AOKB, then press ENTER.
● If you do not want to delete the scene, press RETURN.
To modify the points
A Press RETURN.
B Repeat steps 4 – 8 as necessary.
9
Press D E to select ADELETEB, then press ENTER. The
selected scene is deleted.
● To cancel the deletion, press D E to select ACANCELB, then
press ENTER.
10 Press EDIT to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● Available recording capacity may not match the deleted part after
deletion.
Filename [DVM70S_11Navigation.fm]
Masterpage:Right+
DVM70S_00.book Page 53 Friday, May 6, 2005 12:06 PM
NAVIGATION ON HDD/DVD DECK
Divide Title (HDD deck only)
1
2
3
4
5
EN
53
Edit Play List Information
Press EDIT. The Editing screen appears.
Press FGD E to select ADIVIDEB, then press ENTER.
Press FGD E to select a title to divide, then press ENTER.
Press I to start playback. Press O or N to locate a point to
divide, then press W.
Confirm the arrow is on ADIVIDEB, then press ENTER.
● The first picture (start) of the newly created title appears in the
bottom right window.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
● Load a DVD disc to modify.
● Select APREVIEWB, then press ENTER. The first several
seconds of the newly created title is played back, then the
playback pauses at the dividing point.
● To undo the division, press D E to select ARETRYB, then press
ENTER. Repeat the above procedure to locate another point to
divide.
6
7
Press D E to select AOKB, then press ENTER.
ATTENTION:
● It is not possible to modify discs recorded on DVD units from
other manufacturers.
● You cannot perform timer recording during editing the index by
pressing EDIT. Press EDIT to clear the editing screen before
performing timer recording.
Press D E to select ADIVIDEB, then press ENTER.
● Select ACANCELB, then press ENTER to return to the previous
CABLE/DBS
screen.
8
TV
Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Modify Chapter
(HDD, DVD-RAM & DVD-RW (VR mode) only)
CANCEL
ENTER
You can create and delete chapter marks in titles.
1
Perform steps 1 – 4 of AModify IndexB (A pg. 51) before
continuing.
2
3
Press FGD E to select ACHAPTERB, then press ENTER.
Press I to start playback.
Press O or N, then press
W at the positions you want to
mark.
HDD
S
O
o
EDITING > MODIFY CHAPTER
DVD
DVD
MEMO
EDIT
NAVIGATION
DFGE
T
I
N
W
CHAPTER 03/10
0 : 07 : 01
4
Press D E to select AMARKB,
then press ENTER.
● To undo the marking, press
D E to select ARETRYB, then
press ENTER.
● Repeat the above steps 3 and 4 to locate another point to mark.
01 00 : 00 : 00
MARK
02 00 : 05 : 30
03 00 : 07 : 00
ERASE
RETRY
04 00 : 30 : 00
RETURN
5
Press S or T to select one chapter you want to delete,
press D E to select AERASEB, then press ENTER.
● To undo the deletion, press D E to select ARETRYB, then press
ENTER.
6
Press EDIT to return to the normal screen.
NOTE:
There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
Page 53Friday, 6 May 2005 12:06
Play List
It is a collection of the scenes. A play list can be freely edited and
played back without ever changing any original recording data.
Using the random access of a disc (which allows video data to be
instantly read no matter where it is on the disc), a play list includes
information such as the timer counter for the playback start point
and end point, indexes for checking the contents of recorded data,
category information, and more. Playback according to a play list
you have created allows you to enjoy various combinations of
video images from a single title.
Filename [DVM70S_11Navigation.fm]
Masterpage:Left+
DVM70S_00.book Page 54 Friday, May 6, 2005 12:06 PM
54 EN NAVIGATION ON HDD/DVD DECK
Create Play List
1
2
3
4
5
1
Perform steps 1 – 5 in AEdit ScenesB (A pg. 54) before
continuing.
2
3
Press FGD E to select ASEL. TITLEB, then press ENTER.
Press FGD E to select ACREATEB, then press ENTER.
Press FGD E to select a title that includes scenes to be
included in a play list, then press ENTER.
Move Scenes
Press I to start playback. Press O or N to find the point
where you want the created play list to begin, then press W.
1
Perform steps 1 – 5 of AEdit ScenesB (A pg. 54) before
continuing.
2
3
4
Press FGD E to select AMOVEB, then press ENTER.
5
Perform steps 9 – 11 in ACreate Play ListB (A pg. 54).
Press EDIT. The Editing screen appears.
(DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
6
Confirm the arrow is on AIN/
OUTB, then press ENTER.
● The edit-in time is displayed on
the screen.
● To undo, press D E to select
ARETRYB, then press ENTER.
7
Add scenes
TOTAL TIME
EDITING > PLAY LIST/CREATE
SCENE
00 : 00 : 00
PAGE
1/1
1 PRO. 1
2
3
4
PRO. 1
5
0 : 00 :15
6
7
Press I to start playback.
Press O or N to find the
point where you want the
created play list to end, then press W.
IN
8
OUT
IN/OUT
MODIFY
MOVE
PREVIEW
SEL. TITLE
DELETE
RETRY
OK
8
Confirm the arrow is on AIN/OUTB, then press ENTER.
● The edit-out time is displayed on the screen.
● The edit-out point must come after the edit-in point.
● Select APREVIEWB, then press ENTER to preview the play list.
9 Press FGD E to select AOKB, then press ENTER.
10 Press D E to select AEXITB, then press ENTER
11 Press EDIT to return to the normal screen.
NOTES:
● There may be a discrepancy of several seconds between the
scene you intend to edit, and the scene which is actually edited.
● The title, index and category of the play list can be modified in the
same way as AORIGINALB. (A pg. 51)
● You can modify the play list that has just been created here by
adding, moving, or deleting unwanted parts to create a digest
edition, etc.
Edit Scenes
1
2
3
Press EDIT. The Editing screen appears.
(DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
Press FGD E to select AMODIFYB under APLAY LISTB, then
press ENTER.
4
5
6
7
Press FGD E to select a play list to modify, then press ENTER.
8
Perform steps 5 – 11 in ACreate Play ListB (A pg. 54).
Press FGD E to select ASCENEB, then press ENTER.
Press FGD E to select AMODIFYB, then press ENTER.
Press FGD E to select the start or end point of a scene to
modify, then press ENTER.
Page 54Friday, 6 May 2005 12:06
Perform steps 4 – 11 in ACreate Play ListB (A pg. 54).
Press F G to select a scene to move, then press ENTER.
Press F G to select another scene to which the scene is to be
moved, then press ENTER.
● To cancel the move, press FGD E to select ARETRYB, then
press ENTER.
Delete Scenes
1
Perform steps 1 – 5 of AEdit ScenesB (A pg. 54) before
continuing.
2
3
4
Press FGD E to select ADELETEB, then press ENTER.
Press F G to select a scene to delete, then press ENTER.
Perform steps 9 – 11 in ACreate Play ListB (A pg. 54).
Play Back Play List
1
Press NAVIGATION. The Library Database Navigation screen
appears.
2
3
Press FGD E to select APLAY LISTB, then press ENTER.
Press FGD E to select the
index (small pictures) of the
desired play list, then press
ENTER.
● When you want the plural play
lists to be played back
continuously, press MEMO
after selecting the desired play
lists. The numbers of the
playback order appear on the index. You can select up to 8 play
lists.
● When you want to correct the order, move the arrow to the
desired index and press MEMO. The number disappears and
the unit re-numbers the other play lists automatically.
● When you want to cancel the order, press CANCEL(L).
NAVIGATION > PLAY LIST
0026 [FISH WORLD
]
143 MIN
026 CREATED 26/12/03 FRI
TEDDY BEAR 25/12
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
4
NAVIGATION
ENTER
EXIT
SELECT
[MOVIES]
001
002
003
004
005
006
007
008
009
Press D E to select ABEGINNINGB, then press ENTER. The
playback starts.
● Upon completing play list playback, the normal screen will
resume.
● The normal screen will also resume when o is pressed to stop
play list playback.
Filename [DVM70S_11Navigation.fm]
Masterpage:Right+
DVM70S_00.book Page 55 Friday, May 6, 2005 12:06 PM
NAVIGATION ON HDD/DVD DECK
Delete Play List
1
2
3
EN
55
Edit Library Information
Press EDIT. The Editing screen appears.
(DVD deck only) Press FGD E to select AMODIFYB under
AORIGINAL/PLAY LISTB, then press ENTER.
Press FGD E to select ADELETEB under APLAY LISTB, then
press ENTER.
4
Press FGD E to select one play list you want to delete, then
press ENTER.
5
Press D E to select ADELETEB, then press ENTER.
6
Press EDIT to return to the normal screen.
● When you cancel the deletion, select ACANCELB, then press
ENTER.
Title information can be registered in the unit’s memory for up to
600 DVD discs, 2,000 titles. It is helpful when finding a desired title
(or play list) by sorting according to the sort options registered
during (or after) recording.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press HDD or DVD to choose the corresponding deck.
NOTE:
Even if a play list is deleted, the titles recorded and the library
information are not affected at all.
CABLE/DBS
TV
HDD
Modify Index
DVD
DVD
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
B Perform steps 5 – 8 of AModify IndexB (A pg. 51).
Modify Play List Name
ENTER
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
B Perform steps 2 – 5 of AModify Title NameB (A pg. 51).
NAVIGATION
FGDE
Modify Category
A Perform steps 1 – 4 of AEdit ScenesB (A pg. 54) before
continuing.
B Perform steps 2 – 4 of AModify CategoryB (A pg. 52).
Scan For Title From Library
1
Press NAVIGATION. The Library Database Navigation screen
appears.
2
Press FGD E to select the
appropriate sort button to sort
the information, then press
ENTER.
ADATEB:
Sort by date
ADISC No.B:
A
Sort by disc number
ACATEGORYB:
Sort by category
ANAMEB:
Sort by name
● ADATEB and ADISC No.B are available for the DVD deck only.
NAVIGATION
DVD NAVIGATION
ORIGINAL
PLAY LIST
SELECT WITH @
THEN PRESS [ENTER]
PRESS [NAVIGATION]
TO EXIT
NAVIGATI
EXIT
3
DVD LIBRARY
DATE
DISC No.
CATEGORY
NAME
ENTER
SELECT
Press FGD E to select the desired title, then press ENTER.
● Playback begins automatically after the selected title is located.
NOTE:
If a disc registered in the library is recorded or modified on DVD
units from other manufacturers, it may become impossible to
operate properly.
Register Disc
When a disc that is not registered in the library is loaded, a
message appears confirming if the disc should be registered. If
registering, perform the following procedure.
1
Press D E to select AREGISTERB, then press ENTER to confirm
the registration.
2
Press NAVIGATION to return to the normal screen.
NOTES:
● It is not possible to register discs formatted on devices other than
JVC’s DVD recorders.
● It is not possible to register discs recorded on devices other than
JVC’s DVD recorders.
● It is not possible to register discs when ASAVE AS LIBRARYB is
set to AOFFB. (A pg. 71)
Page 55Friday, 6 May 2005 12:06
Filename [DVM70S_11Navigation.fm]
Masterpage:Left+
DVM70S_00.book Page 56 Friday, May 6, 2005 12:06 PM
56
EN
NAVIGATION ON HDD/DVD DECK
Playback With MP3/WMA/JPEG
Navigation
This unit can play back discs that MP3/WMA sound files and JPEG
image files taken with digital still cameras or other devices are
recorded.
The MP3/WMA/JPEG Navigation enables you to search and select
the desired files recorded on CD-R/RW or CD-ROM discs very
easily.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Press DVD to select the DVD deck.
NAVIGATION > ORIGINAL
GROUP : 001/100
TRACK : 001/100
0 : 07 : 01
IT’S SHOWTIME ! ! /B’z
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
A Selected group number/total number of groups on the disc
B Selected file number/total number of files in the group that
contains the selected file
C Elapsed time (MP3 only)
D Name of the selected file
E Group name
F Selected file
NOTES:
● If there are more than 100 files, the rest of the files are not
displayed. In this case, press ON SCREEN to display them on
the TV screen.
● If both MP3 files and WMA files are recorded on the same disc,
WMA files cannot be played back as they are not displayed on
the navigation screen.
Page 56Friday, 6 May 2005 12:06
Locating The Desired Group And Tracks
1
2
3
4
Load a disc.
Press NAVIGATION.
Press FGD E to select AORIGINALB, then press ENTER.
Press F G to select the
desired group, then press
ENTER.
● A list of files in the selected
group appears.
5
Press F G to select the
desired item, then press
ENTER. The unit starts
playback from the selected
item.
● The unit stops when all items
in the selected group are
played back.
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NAVIGATION > ORIGINAL
GROUP : 001/100
IT’S SHOWTIME ! ! /B’z
TRACK : 001/100
0 : 07 : 01
ROOT
001. IT’S SHOWTIME ! ! /B’z
CLASSIC
002. ONLY FLOWER IN THE WORLD/SMAP
CLUB
003. SEXY GUY/GOMAKI
DANCE
004. HEY?/AYAYA
EUROPE
005. DOOR TO TOMORROW/I WISH
FOREIGN GROUP
006. REASON/ASAMI
FOREIGN ROCK
007. DIE ANOTHER DAY/JAMES BOND
NOTES:
● If you press SELECT(I) instead of ENTER in step 4, the unit
starts playback from the first file of the group.
● JPEG files are played back as a slide show at the set intervals.
(A pg. 32)
● If a file name includes any 2-byte character, the unit may not
show the file name correctly.
● The order of the groups and items shown in steps 4 and 5 may
differ from the order shown on your PC.
Filename [DVM70S_12Editing.fm]
Masterpage:Right0
DVM70S_00.book Page 57 Friday, May 6, 2005 12:06 PM
EDITING
EN
57
● It is not possible to dub the following programs to DVD-R/RW
Dubbing
disc (Video mode):
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
DV
DVD
DVD
MARK
DUBBING
ENTER
FGDE
●
●
●
●
which contains more than one audio language.
which is on the play list.
which is edited (also RetroActive Recording).
which is recorded in LP mode or FP155-FP240 mode.
● Recording may not be performed in the highest speed depending
on the characteristics of the disc used.
1
2
3
4
5
Load a recordable disc.
6
Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
press ENTER to start dubbing.
Press DUBBING to access the Dubbing Menu screen.
Press FGD E to select AHDDNDVDB, then press ENTER.
Press FGD E to select AHIGH SPEEDB, then press ENTER.
Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
● The recordable time of the disc is displayed on the bar meter.
For details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
NOTES:
R
o
W
ON SCREEN
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
● It is not possible to discontinue dubbing once it has been started.
Just Dubbing (From HDD To DVD)
Auto Finalizing
When dubbing from a Mini DV or HDD to a DVD (Video mode)
disc, you can select whether to finalize the disc automatically
after dubbing has been completed.
It is also possible to create a disc in the desired playback format
when finalizing the disc. Each time the finalized disc is played
back, it will be played back in accordance to the setting you have
selected during finalization. For details, refer to ADISC TYPEB
(A pg. 71).
NOTE:
With Auto Finalizing, the background after finalization will be the
same as that used during the previous finalization.
NOTES:
● It is not possible to dub copy-protected contents. An error
message will appear on the TV screen.
● It is not possible to dub simultaneously when timer
programming is set. Select either dubbing or timer
programming.
● The order of the index which are displayed by pressing
DUBBING differs from the images displayed by pressing
NAVIGATION or EDIT.
High Speed Dubbing (From HDD To DVD)
It is possible to dub the original recordings and/or play lists on the
HDD deck to DVD discs. The dubbing is performed in high speed,
keeping the original transfer rate.
NOTES:
● After accessing the Dubbing Menu screen, it is not possible to
take out a disc.
● It is not possible to dub copy-once titles in Video mode.
● When dubbing a copy-once title, the data will be moved from
HDD to DVD upon completing dubbing.
● When you cancel dubbing a copy-once title during dubbing, the
original recording on the HDD deck remains and the title copied
to a DVD disc is deleted.
● It is not possible to dub play lists which contain copy-once titles.
Page 57
By using Just Dubbing function, when dubbing all selected original
recordings and/or play lists, the unit automatically sets the
appropriate recording mode depending on the combination of the
total time of the selected recordings and/or play lists to be dubbed
and the available disc space.
1
2
3
4
5
Load a recordable disc.
Press DUBBING to access the Dubbing Menu screen.
Press FGD E to select AHDDNDVDB, then press ENTER.
Press FGD E to select AJUSTB, then press ENTER.
Perform steps 5 – 6 of AHigh Speed Dubbing (From HDD To DVD)B.
NOTES:
● Play lists are dubbed as programs.
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
However, the lower transfer rate cannot be dubbed in the higher
transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
● It is not possible to discontinue dubbing once it has been started.
Manual Dubbing (From HDD To DVD)
It is possible to perform dubbing in the desired transfer rate.
1
2
3
4
5
Load a recordable disc.
6
Press F G to select AREC MODEB, then press ENTER. Press
F G to select the desired option, then press ENTER.
7
8
Press G to select ACONFIRMB, then press ENTER.
Press DUBBING to access the Dubbing Menu screen.
Press FGD E to select AHDDNDVDB, then press ENTER.
Press FGD E to select AMANUALB, then press ENTER.
Perform step 5 of AHigh Speed Dubbing (From HDD To DVD)B.
The Manual Dubbing screen appears.
Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
press ENTER to start dubbing.
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 58 Friday, May 6, 2005 12:06 PM
58
EN
EDITING
NOTES:
● In Video mode, if the selected play list includes the scenes
recorded in the different transfer rate, the dubbing is performed in
the highest transfer rate of the scenes in the selected play list.
However, the lower transfer rate cannot be dubbed in the higher
transfer rate.
● The recordable time of the disc is displayed on the bar meter. For
details, refer to AAbout Disc Remaining DisplayB (A pg. 59).
● During dubbing, it is not possible to play back on HDD or DVD, or
to set timer programming.
● It is not possible to discontinue dubbing once it has been started.
Dubbing From HDD To DV
It is possible to perform dubbing from the HDD deck to the DV
deck.
1
2
3
4
Load a Mini DV cassette with the erase protection switch set to
ARECB.
Press DUBBING to access the Dubbing Menu screen.
Press FGD E to select AHDDNDVB, then press ENTER.
Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
Dubbing From DVD To DV
It is possible to perform dubbing from the DVD deck to the DV
deck.
1
Load the disc you want to dub onto the DVD deck, and a Mini
DV cassette with the erase protection switch set to ARECB to the
DV deck.
2
3
4
Press DUBBING to access the Dubbing Menu screen.
5
Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER. The confirmation screen appears.
Press FGD E to select ADVDNDVB, then press ENTER.
Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
6
Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
● Sound mode selection is not available when dubbing a
DVD-RW (Video mode) or DVD-R disc.
7
Press G to select ACONFIRMB, then press ENTER. The
confirmation screen appears.
Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
8
9
Press DV so that the DV lamp lights up on the unit.
Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
10 Press DVD so that the DVD lamp lights up on the unit.
7
Press G to select ACONFIRMB, then press ENTER. The
confirmation screen appears.
11 Press D E to select AEXECUTEB, then press ENTER to
8
9
Press DV so that the DV lamp lights up on the unit.
5
6
Press I to locate the point from where you want to start
dubbing, then press R and W simultaneously so that the DV
deck enters the record pause mode.
10 Press HDD so that the HDD lamp lights up on the unit.
● The dubbing screen will appear.
11 Press D E to select AEXECUTEB, then press ENTER for
confirmation.
● To cancel the dubbing, press o then D E to select ACANCELB
Press I to locate the point from where you want to start
dubbing, then press R and W simultaneously so that the DV
deck enters the record pause mode.
● The dubbing screen will appear.
confirm.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
12 Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
NOTES:
● It is not possible to dub play lists on DVD discs.
● It is not possible to dub Video CDs/SVCDs or Audio CDs.
● When dubbing is in progress, only o is functional.
and press ENTER to confirm.
12 Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
Original Dubbing (From DVD To HDD)
It is possible to dub the original recordings on DVD discs to the
HDD deck.
1
2
3
4
Load a disc you want to dub.
5
Press D E to select AEXECUTEB, then press ENTER to start
dubbing.
Press DUBBING to access the Dubbing Menu screen.
Press FGD E to select ADVDNHDDB, then press ENTER.
Press FGD E to select indexes (small pictures) of desired
original recordings and/or play lists, then press MARK. After
selecting all indexes you want to dub, press ENTER.
● You can select up to 8 original recordings and/or play lists.
NOTES:
is not possible to dub play lists on DVD discs.
is not possible to dub pre-recorded DVD VIDEO discs.
is not possible to dub Video CDs/SVCDs or Audio CDs.
is not possible to discontinue dubbing once it has been started.
● It
● It
● It
● It
Page 58
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Right+
DVM70S_00.book Page 59 Friday, May 6, 2005 12:06 PM
EDITING
Dubbing From DV To HDD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the DV deck to the HDD deck using
the AENTIREB dubbing.
1
Load the Mini DV cassette you want to dub. Make sure its erase
protection switch is set to ASAVEB.
● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)
EN
59
9
Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
● The tape will automatically be rewound.
NOTES:
● ASUPERIMPOSEB is automatically set to AOFFB. It will return to
AAUTOB after dubbing is completed.
● The program information at the DV deck will not be dubbed.
● When there are blanks on the tape of more than 2 seconds, the
DVD deck will enter into pause mode. Dubbing will resume once
recorded portion is detected.
● Dubbing copyright guarded tape is not possible.
● When dubbing is in progress, only o is functional.
2
3
4
5
Press DUBBING to access the Dubbing Menu screen.
6
Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
7
About Disc Remaining Display
When dubbing from HDD to DVD, the unit displays the time
information for dubbing by bar meter. By comparing the disc
remaining time and the necessary time for dubbing of the selected
items, it is possible to check if the dubbing can be performed
completely or not.
Press G to select ACONFIRMB, then press ENTER. The
confirmation screen appears.
When performing the High Speed Dubbing
Press FGD E to select ADVNHDDB, then press ENTER.
Select AENTIREB, then press ENTER.
Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
8
Press D E to select AEXECUTEB, then press ENTER for
confirmation.
● Once dubbing starts, it will continue dubbing until the end of the
tape is reached.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after
automatically rewinding the tape to the beginning.
Capacity of a disc
Remaining capacity
21%
Dark green: Length of already recorded item
Light green: Length of selected item
Yellow: Length of the item now being selected by arrow
Red: Excess over the capacity
9
Upon completing dubbing, the tape stops and ADUBBING
COMPLETEDB appears on the TV screen. Press ENTER to
end.
● The tape will automatically be rewound.
NOTES:
● ASUPERIMPOSEB is automatically set to AOFFB. It will return to
AAUTOB after dubbing is completed.
● When there are blanks on the tape of more than 2 seconds, the
HDD deck will enter into pause mode. Dubbing will resume once
recorded portion is detected.
● Dubbing copyright guarded tape is not possible.
● When dubbing is in progress, only o is functional.
Dubbing From DV To DVD
(Dubbing An Entire Cassette)
It is possible to perform automatic dubbing of all the recorded
programs of a cassette from the DV deck to the DVD deck using
the AENTIREB dubbing.
When performing the Just Dubbing
TOTAL 105MIN
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The total time of a loaded disc is displayed on the right of the bar
meter.
When performing the Manual Dubbing
MAX FR240
● The unit displays the status on the assumption that the selected
items are dubbed in the lowest transfer rate.
● The available highest transfer rate is displayed on the right of the
bar meter.
1
Load the Mini DV cassette you want to dub. Make sure its erase
protection switch is set to ASAVEB.
● Set ADV AUDIO RECB to the appropriate mode. (A pg. 71)
2
3
4
5
Press DUBBING to access the Dubbing Menu screen.
6
Press F G to select ASELECT SOUND MODEB, then press
ENTER. Press F G to select the desired option, then press
ENTER.
7
Press G to select ACONFIRMB, then press ENTER. The
confirmation screen appears.
Press FGD E to select ADVNDVDB, then press ENTER.
Select AENTIREB, then press ENTER.
Press F G to select ASELECT RECORDING MODEB, then
press ENTER. Press F G to select the desired option, then
press ENTER.
8
Press D E to select AEXECUTEB or AAUTO FINALIZEB, then
press ENTER for confirmation.
● Once dubbing starts, it will continue dubbing until the end of the
tape is reached.
● To cancel the dubbing, press o then D E to select ACANCELB
and press ENTER to confirm.
● If the tape is not rewind, the unit will start dubbing after
automatically rewinding the tape to the beginning.
Page 59
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 60 Friday, May 6, 2005 12:06 PM
60
EN
EDITING
DV Dubbing (HDD & DVD Deck Only)
The following on-screen display for DV dubbing appears when
ON SCREEN is pressed while the channel has been set to ADVB.
You can dub programs from a camcorder or DV equipment
connected to the unit with a DV cable. The unit’s remote control
allows you the limited control of the connected camcorder or DV
equipment functions during dubbing.
NOTES:
● Use the DV cable VC-VDV 204U for connection.
● When you connect a PC to the [DV IN] connector, we do not
assure the normal operation of this unit.
Your unit
To [DV IN]
HDD
FR360
12bit
0:00
1:00
00:00:00. 00
JVC
DV
DV
A
2:00
DV
B
DV
GR-DV3500
00:00:00. 00
L – R
SOUND1
GR-DV3500
1 2
C
A Remote control switch
To switch between the devices operable by the remote control
unit. The unit is operable when the remote icon (
)
displayed faces to the left, while the DV device is operable
when the remote icon is facing to the right.
B Auto capture button
Select to start or pause the dubbing. If ENTER is pressed when
the DV device is in the pause condition, preroll editing* where it
is possible to dub with a start time that is highly accurate will be
activated. When the DV device cannot be operated from the
unit (such as in camera mode), proceed with normal recording
(A pg. 34, 37).
* Preroll editing refers to the playback after the DV tape is slightly
rewind. (For DV devices that do not support the –1x speed, the
rewinding time may be longer.)
Camcorder
DV cable
(VC-VDV 204U)
(not supplied)
DV connector
C Sound monitor switch
For selecting the desired sound format for dubbing.
1
Connect a camcorder or DV equipment to the [DV IN]
connector on the unit’s front panel.
2
Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
3
4
Press CH +/- to set the channel to ADVB.
5
Press D E to select
, then press ENTER to display
the remote icon (facing to the right) for the DV equipment.
6
7
Press REC MODE repeatedly to set the recording mode.
8
Press D E to select
, then press ENTER repeatedly
until the desired sound track appears on the TV screen.
Press ON SCREEN.
● The on-screen display for DV dubbing appears.
DV equipment
Locate the point from where you want to start dubbing, then
stop or pause playback by pressing the following buttons on the
remote control: I, N, O, o, W.
● To play back in slow speed (1/10 of the normal speed), press W
to pause playback, then press O or N.
● To play back frame-by-frame, press W to pause playback, then
press W repeatedly. Each press of W advances a frame.
● To change the playback direction, press O or N.
SOUND1:
Select this to record the original stereo sound played back on
the connected DV equipment.
SOUND2:
Select this to record the dubbed stereo sound played back on
the connected DV equipment.
MIX:
Select this to record the sound of both ASOUND1B and
ASOUND2B.
● Note that this selection is not available when the source
program is recorded in 16BIT (48 kHz) mode.
9
Press D E to select
, then press ENTER. The
dubbing starts.
● Playback on the external DV equipment and recording on the
unit should start simultaneously.
● To pause dubbing, press D E to select
, then press
ENTER. Both the unit and the external DV equipment pause
dubbing. Pressing W on the unit also works the same way.
10 Press D E to select
, then press ENTER. Then
press o. The DV equipment stops.
11 Press D E to select
Page 60
, then press ENTER.
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
DVM70S_00.book Page 61 Friday, May 6, 2005 12:06 PM
Masterpage:Right+
EDITING
EN
61
12 Press o twice on the remote control to stop dubbing.
● Both the unit and the external DV equipment stop dubbing.
NOTES:
● Dubbing copyright guarded programs is not possible.
● Original DV information such as the recording date and time are
not recorded.
● The superimposed indication during the operation or dubbing is
not recorded.
● If the dubbing is paused while the channel is set to ADVB, you
cannot switch channels.
When you dub from DV equipment other than a
camcorder
A Perform step 1 to 4.
B Locate the point from where you want to start dubbing,
then stop on the DV equipment.
● If you pause the DV equipment in this step, a few
second’s still picture will be recorded at the beginning of
the recorded program.
C Set the input mode to ADV INPUTB on the DV equipment.
● If you select an input mode other than ADV INPUTB,
unwanted pictures may be recorded at the beginning of
the recorded program.
D Perform step 9 to 12.
To skip unwanted part of the source picture
Press ENTER to stop both equipment, then press D E to select
.
Locate the point where you want to restart dubbing by pressing I,
N, or O, then press o.
Press D E to select
, then press ENTER to restart
dubbing.
Page 61
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 62 Friday, May 6, 2005 12:06 PM
62
EN
EDITING
Edit From A Camcorder
● Slide the TV/CABLE/DBS/DVD switch to DVD.
You can use a camcorder as the source player and your unit as the
recording deck. If your camcorder has a DV IN/OUT connector,
you can use the camcorder as the recording deck and your unit as
the source player.
A If the camcorder has no S-VIDEO output connector:
Recorder
To [VIDEO/AUDIO
((MONO) L/R)] input
Audio/video cable
(not supplied)
1 Make connections.
A If the camcorder has no S-VIDEO output connector:
^ connect the camcorder’s AUDIO/VIDEO OUT connectors to
the unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors
on the front panel.
● When using a monaural camcorder, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
B If the camcorder has an S-VIDEO output connector:
^ connect the camcorder’s AUDIO OUT and S-VIDEO OUT
connectors to the unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
C If the camcorder has a DV IN/OUT connector:
^ connect the camcorder’s DV IN/OUT connector to the unit’s
[DV IN/OUT] connector.
● When using your unit as the source player, refer to the
camcorder’s instruction manual for the recording procedure.
2
Press DV/HDD/DVD on the unit repeatedly to select the
recording deck.
3
Press CH +/- to select AF-1B or ADVB.
● Set AFRONT AUX F-1B to AVIDEOB for the [VIDEO] input
connector, or AS-VIDEOB for the [S-VIDEO] input connector,
depending on the connector being used. (A pg. 72)
AUDIO/VIDEO OUT
Player
B If the camcorder has an S-VIDEO output connector:
To [S-VIDEO]
input
Recorder
To [AUDIO] input
S-video cable
(not supplied)
S-VIDEO
OUTPUT
Audio cable
(not
supplied)
4
5
Press REC MODE repeatedly to set the recording mode.
6
Press R on the unit to start recording. Or while holding R, press
I on the remote control. The dubbing starts.
7
Press o on the unit, then stop playback on the camcorder.
Start playback on the camcorder slightly before the actual point
from where you wish to start dubbing.
NOTES:
● All necessary cables can be obtained from your dealer.
● Refer to the camcorder’s instruction manual for operating
procedure.
● The quality of dubbed picture becomes poorer than that of the
original.
● When you are editing through the [DV IN/OUT] connector, the
unit will stop if the player begins playing a blank portion of tape or
the signal is interrupted.
● When connecting the unit to a device equipped with a DV input
connector, be sure to use the optional DV cable (VC-VDV204U)
● To edit through the [DV IN/OUT] connector using the HDD or
DVD deck, refer to ADV Dubbing (HDD & DVD Deck Only)B
(A pg. 60).
AUDIO OUTPUT
Player
C If the camcorder has a DV IN/OUT connector:
Recorder/Player
To [DV IN]
DV cable
(VC-VDV 204VU)
(not supplied)
DV connector
Player/Recorder
Page 62
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Right+
DVM70S_00.book Page 63 Friday, May 6, 2005 12:06 PM
EDITING
Edit To Or From Another Recorder
You can use your unit as the source player or as the recording
deck.
NOTES:
● When using another recorder as the recording deck, refer to its
instruction manual.
● It is not possible to dub copy-protected contents. An error
message will appear on the TV screen.
A When using your unit as the source player
TV receiver
EN
63
● Slide the TV/CABLE/DBS/DVD switch to DVD.
1 Make connections.
A When using your unit as the source player:
^ connect its [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors
to the input connectors on another recorder.
B When using your unit as the recording deck:
^ connect its [S-VIDEO/VIDEO/AUDIO OUTPUT] connectors
on the front or rear panel to the output connectors on
another recorder.
● When connecting to another recorder with S-video connector,
set AREAR AUX L-1B or AFRONT AUX F-1B to AS-VIDEOB.
2
Press CH +/- to select the external input.
● Select AF-1B when the source player is connected to the unit’s
Player
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
front panel, and select AL-1B when it is connected to the unit’s
[VIDEO/AUDIO] or [S-VIDEO/AUDIO] input connectors on the
rear panel.
Your unit
3
4
5
6
Press REC MODE repeatedly to set the recording mode.
Engage the Play mode on the source player.
Engage the Record mode on the recording deck.
Stop recording on the recording deck, then stop playback on
the source player.
NOTES:
● All necessary cables can be obtained from your dealer.
● When you use this unit as the source player for editing, be sure to
set ASUPERIMPOSEB to AOFFB before starting. (A pg. 72)
Another recorder
Recorder
B When using your unit as the recording deck
TV receiver
Player
Your unit
Another recorder
Recorder
Page 63
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 64 Friday, May 6, 2005 12:06 PM
64
EN
EDITING
Digital Audio Dubbing
You can dub selected audio from a DVD or Audio CD disc to a
digital audio device.
However, it is not possible to dub copy-protected discs.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Example: Dubbing to an MD
Recorder
1
Connect the unit and a digital audio device using either an
optional optical cable or an optional coaxial cable.
2
Place a disc on the unit and load an MD on the connected
digital audio device.
3
4
Select the audio to be dubbed.
5
6
7
8
9
Press W to pause playback.
Start playback slightly before the actual point from where you
wish to start dubbing.
Select the input mode on the connected digital audio device.
Press I to start playback on the unit.
Start recording on the digital audio device.
Stop recording on the digital audio device. Then press o to stop
playback on the unit.
NOTE:
There may be a discrepancy of several seconds between where
you intend editing to start, and where it actually starts.
Digital audio device
(MD deck, etc.)
Coaxial cable
(not supplied)
Player
To [DIGITAL
AUDIO OUT
(COAXIAL)]
Optical cable
(not supplied)
To [DIGITAL AUDIO
OUT (OPTICAL)]
Rear of unit
Note for connection:
Remove the protection cap from the optical
cable.
Page 64
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Right+
DVM70S_00.book Page 65 Friday, May 6, 2005 12:06 PM
EDITING
Audio Dubbing (DV Deck Only)
65
● Slide the TV/CABLE/DBS/DVD switch to DVD.
This function allows you to record new audio, without erasing the
original audio, on a DV tape that was recorded with ADV AUDIO
RECB set to A12BITB (A pg. 71).
ATTENTION:
You cannot perform Audio Dubbing on a tape that was recorded
with ADV AUDIO RECB set to A16BITB (A pg. 71), on a tape that
was recorded at the ALPB speed, or on a blank tape.
Your unit
EN
Recorder
1
Connect an audio device to the unit’s [AUDIO] input connectors
on the front panel.
● When using a monaural audio device, connect its AUDIO OUT
connector to the [AUDIO-L] input connector on your unit.
2
3
Load a Mini DV cassette with the erase protection switch set to
ARECB.
Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
4
5
Press CH +/- to select AF-1B.
6
7
Press W to pause playback.
Start playback slightly before the actual point from where you
wish to start dubbing.
Press AUDIO DUB. to engage the audio dubbing mode.
● Your unit enters the Audio Dubbing Pause mode.
● To perform Audio Dubbing with audio mixing, press AUDIO to
To [AUDIO]
input
CH +/-
select AL+RB at this point. When using the DV deck as the
recording deck, also make sure that AAUDIO MODEB is set to
ASOUND1B (A pg. 71).
AUDIO DUB.
* Audio Dubbing with audio mixing is not possible if you are using a
monaural audio component, or if you don’t have an audio mixer.
Audio cable
(not supplied)
8
Engage the audio device’s playback, then press I to start the
tape in the unit. Audio dubbing starts at this point.
● To stop dubbing temporarily, press W. Press I to resume
dubbing.
AUDIO OUT
9
CD player, etc.
Press o on the unit, then stop playback on the audio device to
end the audio dubbing.
NOTES:
● Once the Audio Dubbing starts, you cannot use the other deck.
● When monitoring the audio dubbed sound on the DV deck, set
AAUDIO MODEB to ASOUND2B (A pg. 71).
● When playing back an audio dubbed Mini DV tape on the DV
deck, set AAUDIO MODEB to ASOUND2B (A pg. 71).
● Audio dubbing is not possible using the [DV IN/OUT] connector.
● Audio dubbing is not possible on a blank portion of the tape.
CD player, etc.
Mixer output
Audio mixer
Original sound
[AUDIO OUTPUT]
Your unit
To
[AUDIO]
input
Page 65
CH +/-
Recorder
AUDIO DUB.
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 66 Friday, May 6, 2005 12:06 PM
66
EDITING
EN
Insert Editing (DV Deck Only)
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Insert Editing replaces the pictures with new ones, while the audio
soundtrack remains unchanged. For Insert Editing, use your unit
as the recording deck.
ATTENTION:
Insert Editing is not possible with a Mini DV cassette recorded in
LP mode.
A If the player has no S-VIDEO output connector:
CH +/-
Your unit
To [VIDEO/AUDIO
((MONO) L/R)] input
2
Recorder
INSERT
Another recorder
Player
B If the player has an S-VIDEO output connector:
To [S-VIDEO]
input
S-video cable
(not supplied)
S-VIDEO
OUT
To [AUDIO] input
Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
4
5
Press CH +/- to select AF-1B.
6
Press INSERT to engage the insert editing mode.
Press S, T and W to determine the edit-in point (the
beginning of the segment to be replaced).
● Be sure to engage the Still mode at the edit-in point.
you are going to record.
AUDIO/VIDEO OUT
CH +/-
3
Load a Mini DV cassette with the erase protection switch set to
ARECB.
● Your unit enters the Insert Pause mode.
● The TV screen changes from the still picture to the input source
Audio/video
cable
(not supplied)
Your unit
1 Make connections.
A If the player has no S-VIDEO output connector:
^ connect the player’s AUDIO/VIDEO OUT connectors to your
unit’s [VIDEO/AUDIO ((MONO) L/R)] input connectors on
the front panel.
B If the player has an S-VIDEO output connector:
^ connect the player’s AUDIO OUT and S-VIDEO OUT
connectors to your unit’s [AUDIO] and [S-VIDEO] input
connectors on the front panel.
Recorder
7
Load the source cassette and play back the segment that is to
be inserted. When you reach the start of the section of the
source tape that you wish to insert, press I to start the tape in
your unit. Insert editing begins at this point.
8
Press o to stop recording on the DV deck to end insert editing.
NOTES:
● Once the Insert Editing starts, you cannot use the other deck.
● All necessary cables can be obtained from your dealer.
● Insert Editing cannot be performed on a Mini DV cassette that
has had its erase protection switch set to ASAVEB.
● When Insert Editing is performed on a tape that has been
recorded on another video recorder, the inserted portion may
appear distorted.
● A small portion of the recording which precedes an insert edit
may become erased.
● Insert Editing is not possible using the [DV IN/OUT] connector.
● Insert Editing is not possible on a blank portion of the tape.
INSERT
Audio cable
(not supplied)
AUDIO OUT
Another recorder
Player
Page 66
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Right0
DVM70S_00.book Page 67 Friday, May 6, 2005 12:06 PM
REMOTE CONTROL
Remote Control Functions
EN
67
CABLE/DBS
TV / VIDEO
Remote Control 1/2/3/4 Code Switching
TV
DVD
A
The remote control is capable of controlling four JVC video units
independently. Each of the units can respond to one of the four
codes (1, 2, 3 or 4). The remote control is preset to send code 3
signals because your unit is initially set to respond to code 3
signals. You can easily modify your unit to respond to code 1, 2 or
4 signals.
0–9
TV VOL +/CH +/-
TV MUTING
ENTER
● Slide the TV/CABLE/DBS/DVD switch to DVD.
SET UP
A
I
CABLE/DBS
TV
DVD
1–4
TV Multi-Brand Remote Control
Your remote control can operate the basic functions of your TV set.
In addition to JVC TVs, other manufacturer’s TVs can also be
controlled.
ENTER
● Turn off the TV using its remote control.
● Slide the TV/CABLE/DBS/DVD switch to TV.
o
SET UP
IMPORTANT:
Although the provided remote control unit is compatible with JVC
televisions, as well as many other models, it may not work with
your TV, or in some instances, may have limited function
capability.
● Keep pressing SET UP down during step 1.
1
Enter your TV’s brand code using the number keys, then press
ENTER.
2
● Keep pressing SET UP down during step 1.
1
Press the number key A1B for 1, A2B for 2, A3B for 3 or A4B for 4 to
change the remote control code, then press ENTER.
2
3
Press A on the unit to turn off the unit.
4
Press o on the remote control to change the unit’s code. The
code currently set on the remote control blinks on the front
display panel for approximately 5 seconds, and is applied to the
unit.
Press I on the unit for over 5 seconds while the unit is turned
off. The code currently set appears on the front display panel.
Press A on the unit’s remote control to turn on the TV and try
operations (A step 3).
● Once you have set the remote control to operate the TV, you do
not have to repeat this step until you replace your remote
control’s batteries.
● Some brands of TVs have more than one code. If the TV does
not function with one code, try entering another.
3
Press the corresponding buttons to operate the TV: A,
TV/VIDEO, CH +/-, TV VOL +/–, TV, number keys.
● For some brands of TVs, you must press ENTER after having
pressed the number keys.
NOTE:
When APOWER SAVEB is set to AONB (A pg. 72), it is not possible
to change the remote code.
Page 67
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Left+
DVM70S_00.book Page 68 Friday, May 6, 2005 12:06 PM
68
EN
REMOTE CONTROL
BRAND NAME
CODE
CABLE BOX BRAND
CODE
JVC
HITACHI
MAGNAVOX
MITSUBISHI
PANASONIC
RCA
SHARP
SONY
SAMSUNG
SANYO
SEARS
TOSHIBA
ZENITH
01, 03
10
02
03
04, 11
05
06
07
12
13
13
08
09
ARCHER
CABLETENNA
CABLEVIEW
CITIZEN
CURTIS
DIAMOND
GC BRAND
GEMINI
GENERAL INSTRUMENTS
HAMLIN
JASCO
JERROLD
NOVAVISION
OAK
PANASONIC
PULSER
RCA
REGAL
REMBRANDT
SAMSUNG
SCIENTIFIC ATLANTA
SIGMA
SL MARX
SPRUCER
STARGATE
TELEVIEW
TOCOM
UNIKA
UNIVERSAL
VIDEOWAY
ZENITH
01, 05, 17
01, 17
15, 16, 17, 21, 25
15, 16, 17, 21, 25
02
01, 17
15, 16, 17, 21, 25
15
01, 04, 06, 11, 12, 15, 28
10, 18, 23
15
01, 04, 06, 11, 12, 15, 28
02
07
13, 14
15, 16, 17, 21, 25
13, 14
10, 18, 23
01, 16, 17
05, 16, 24
02
07
05, 16, 17, 24, 25
13, 14
05, 15, 16, 17, 21, 24, 25
05, 16, 24
01, 04, 16
01, 17
16, 17, 25
03, 09, 22
03, 09, 22
DBS RECEIVER BRAND
CODE
JVC (DISH Network)
ECHOSTAR (DISH Network)
SONY (DSS)
RCA (DSS)
51
51
41
40
Cable Box Or DBS Receiver Multi-Brand Remote
Control
Your remote control can operate the basic functions of your cable
box or DBS (Direct Broadcast Satellite) receiver set. In addition to
JVC cable boxes or DBS receivers, other manufacturer’s cable
boxes or DBS receivers can also be controlled.
● Slide the TV/CABLE/DBS/DVD switch to CABLE/DBS.
● Keep pressing SET UP down during step 1.
1
Enter your cable box or DBS receiver’s brand code using the
number keys, then press ENTER.
2
Press A on the unit’s remote control to turn on the cable box
or DBS receiver and try operations (墌 step 3).
● Once you have set the remote control to operate the cable box
or DBS receiver, you do not have to repeat this step until you
replace your remote control’s batteries.
● Some brands of cable box or DBS receiver have more than one
code. If the cable box or DBS receiver does not function with
one code, try entering another.
3
Press the corresponding buttons to operate the cable box or
DBS receiver: A, CH +/-, number keys.
● For some brands of cable box, you must press ENTER after
having pressed the number keys.
● The number keys may not function with some cable boxes.
IMPORTANT:
It may not work with your cable box, or in some instances, may
have limited function capability.
NOTES:
● It’s not possible to operate a cable box or DBS receiver that is not
equipped with a receiving window.
● It’s not possible to set the remote control for both your cable box
and a DBS receiver at the same time. You can only set the
remote control to operate one of these units at a time.
Page 68
Friday, 6 May 2005 12:06
Filename [DVM70S_12Editing.fm]
Masterpage:Right0
DVM70S_00.book Page 69 Friday, May 6, 2005 12:06 PM
SYSTEM CONNECTIONS
Connecting To A Dolby Digital Decoder
Or An Amplifier With Built-in DTS
These instructions enable you to connect your unit to a Dolby
Digital Decoder or an amplifier with built-in DTS.
1
EN
69
Connect the unit and a Dolby Digital Decoder or an amplifier
with built-in DTS using either an optional optical cable or an
optional coaxial cable.
NOTES:
● For Dolby Digital sound, set ADIGITAL AUDIO OUTB to ADOLBY
DIGITAL/PCMB. (A pg. 70)
● For DTS sound, set ADIGITAL AUDIO OUTB to ASTREAM/PCMB.
(A pg. 70)
CAUTIONS:
● This unit has a dynamic range of more than 110 dB with regards
to its Hi-Fi audio capability. It is recommended that you check the
maximum level if you are going to listen to the Hi-Fi audio signals
through a stereo amplifier. A sudden surge in the input level to
the speakers may damage them.
● Some speakers and televisions are specially shielded to prevent
television interference. If both are of the non-shielded type, do
not place the speakers adjacent to the TV set as this can
adversely affect the playback picture.
Dolby Digital Decoder or
amplifier with built-in DTS
To DIGITAL AUDIO
input
Coaxial cable
(not supplied)
Optical cable
(not supplied)
To [DIGITAL
AUDIO OUT
(COAXIAL)]
To [DIGITAL AUDIO
OUT (OPTICAL)]
Rear of unit
Note for connection:
Remove the protection cap from the
optical cable.
Page 69
Friday, 6 May 2005 12:06
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left0
DVM70S_00.book Page 70 Friday, May 6, 2005 12:06 PM
70
EN
SUBSIDIARY SETTINGS
* The boldface settings below indicate the settings at your purchase.
Mode Set
AUDIO OUTPUT
8 DIGITAL AUDIO OUT ^ DOLBY DIGITAL/PCM / STREAM/
PCM / PCM ONLY
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
Set to the appropriate mode according to the type of the device
connected to [DIGITAL AUDIO OUT] connector.
DOLBY DIGITAL/PCM:
CABLE/DBS
TV
HDD
Select this when you connect the digital input connector of a
Dolby Digital Decoder or an amplifier with a built-in Dolby Digital
Decoder.
DVD
DVD
STREAM/PCM:
Select this when you connect the digital input connector of an
amplifier with a built-in DTS, Dolby Digital, or MPEG
multichannel decoder.
PCM ONLY:
Select this when you connect the linear PCM digital input of
other audio equipment (amplifier, MD or DAT deck, etc.).
ENTER
NOTES:
● This setting also functions when HDD is active.
● If you watch or play back a title which contains multiple audio
languages, select APCM ONLYB in advance and choose main or
sub audio with AUDIO.
FGDE
8 ANALOG AUDIO OUT ^ STEREO / DOLBY SURROUND
SET UP
Select the appropriate setting to accommodate the unit to the
connected A/V equipment. This function takes effect when a
DVD VIDEO disc is played back.
STEREO:
AUDIO
Various modes of this unit are categorized into menus nested in 2
levels shown in the following table. To change the settings of these
modes, find the desired mode in the menu (for details on each
menu, see pages 70 through 72), then follow the procedure below.
DVD VIDEO SET UP
LANGUAGE SET (A pg. 20)
AUDIO OUTPUT (A pg. 70)
PARENTAL LOCK (A pg. 33)
DISC PLAY SET UP (A pg. 71)
Select this when listening to conventional two-channel stereo
audio with the unit’s [AUDIO OUTPUT] connectors connected
to a stereo amplifier/receiver or TV set, or in case you want to
record the audio from a DVD VIDEO disc to a Mini Disc, etc.
DOLBY SURROUND:
Select this when listening to multichannel surround audio with
the unit’s [AUDIO OUTPUT] connectors connected to an
amplifier/receiver with a built-in surround decoder or a surround
decoder.
8 D. RANGE CONTROL ^ NORMAL / WIDE RANGE / TV MODE
The dynamic range (the difference between the loudest sound and
the quietest one) can be compressed during playback of a program
encoded in Dolby Digital format.
This function takes effect when a DVD VIDEO disc recorded in
Dolby Digital format is played back at low or middle volume.
HDD/DVD/DV SET UP
HDD SET UP (A pg. 71)
DVD SET UP (A pg. 71)
DISC SET UP (A pg. 74, 75)
DV SET UP (A pg. 71)
FUNCTION SET UP
REC/PLAY SET UP (A pg. 71)
DISPLAY SET (A pg. 72)
VIDEO IN/OUT (A pg. 23, 72)
WIDE RANGE:
TUNER SET (A pg. 22)
CLOCK SET (A pg. 21)
TV MODE:
INITIAL SET UP
NORMAL:
● The procedure below shows how to set the desired option of the
A2ND AUDIO RECORDB mode as an example.
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
5
6
7
Press D E to select AFUNCTION SET UPB, then press G.
Press D E to select AREC/
PLAY SET UPB, then press G.
Press F G to select A2ND
AUDIO RECORDB, then press
ENTER.
Press F G to select the
desired option, then press
ENTER.
Press SET UP to complete the
setting.
Page 70Friday, 6 May 2005 12:06
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
REC/PLAY SET UP
DISPLAY SET
Select this to deactivate this function when you enjoy wide
dynamic range program.
Select this when you hear the sound through the TV’s
speaker(s).
NOTES:
● This function has no effect on programs other than those
recorded in Dolby Digital format.
● This function does not work when Simulated Surround Effect is
activated. (A pg. 31)
● The effect of ANORMALB and AWIDE RANGEB may not be
different depending on discs.
INITIAL SET UP
8 OUTPUT LEVEL ^ STANDARD / LOW
VIDEO IN/OUT
XP MODE REC AUDIO
DOLBY DIGITAL
2ND AUDIO RECORD
OFF
JUMP TIME
Normally select this setting to activate this function.
15 MIN
You can lower the output level of analog audio to accommodate
the unit to the connected A/V equipment.
STANDARD:
Normally select this setting.
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
LOW:
The output level of analog audio is lowered.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right+
DVM70S_00.book Page 71 Friday, May 6, 2005 12:06 PM
SUBSIDIARY SETTINGS
DISC PLAY SET UP
8 RESUME ^ OFF / ON / DISC RESUME
When this function is set to AONB or ADISC RESUMEB, you can use
the resume function. (A pg. 26)
OFF:
EN
71
ATTENTION:
When changing the settings in the ADV SET UPB menu while in
the DV deck mode, the unit will switch to HDD or DVD deck
mode. To proceed to DV deck after making the changes, press
DV/HDD/DVD on the unit repeatedly or DV on the remote control
to select the DV deck.
You cannot use the resume function.
ON:
You can start playback from the resume point of the placed disc.
DISC RESUME:
The unit retains a memory of the resume points of the last 30
discs played back, even though they have been ejected.
NOTE:
ADISC RESUMEB setting works on DVD VIDEO, VCD, SVCD and
already finalized DVD-R/DVD-RW (video mode) discs. For other
types of discs, the function under AONB setting will be applied even
if ARESUMEB is set to ADISC RESUMEB.
HDD SET UP
8 LIVE MEMORY ^ OFF / 30 MIN / 1 HR / 3 HR
When this function is set to A30 MINB, A1 HRB or A3 HRB, you can
apply the selected time length to ATemporary recording for Live
Memory (HDD deck only)B (A pg. 45).
DVD SET UP
8 SAVE AS LIBRARY ^ OFF / ON
When this function is set to AONB, the recording information is
automatically stored in the library. For details, refer to AEdit Library
InformationB (A pg. 55).
8 CONTINUOUS PLAY ^ OFF / ON
When this function is set to AONB, multiple titles on a disc are
played back continuously one after another.
8 VIDEO MODE RECORDING ASPECT ^ PRIORITIZE 4:3 /
PRIORITIZE 16:9
This is the setting for the aspect ratio used when you dub titles to
DVD discs in video mode. If the titles you want to dub are recorded
in both 16:9 and 4:3, you must select one aspect ratio.
PRIORITIZE 4:3:
If you select APRIORITIZE 4:3B, even a title recorded in 16:9 is
dubbed in 4:3.
PRIORITIZE 16:9:
If you select APRIORITIZE 16:9B, even a title recorded in 4:3 is
dubbed in 16:9.
8 MP3 & WMA / JPEG ^ MP3 & WMA / JPEG
You can select files to play back, when both MP3&WMA files and
JPEG files are recorded on a disc.
MP3 & WMA:
Select this to play back MP3/WMA files.
JPEG:
Select this to play back JPEG files.
8 DISC TYPE ^ MANUAL START / MENU STOP / AUTO
REPEAT
MANUAL START:
To be chosen when you want to playback the disc manually by
pressing I each time after the disc is read.
MENU STOP:
To be chosen when you want playback to stop each time a
menu screen is displayed. The unit automatically starts
playback after the disc is read.
AUTO REPEAT:
To be chosen when you want the disc to be played back
repeatedly each time it is played back. The unit automatically
starts playback after the disc is read.
Page 71Friday, 6 May 2005 12:06
DV SET UP
8 DV AUDIO REC ^12BIT / 16BIT
This is the setting for sound mode before recording on a Mini DV
tape.
12BIT:
Enables Audio Dubbing later.
16BIT:
Audio Dubbing is not possible but the recorded sound quality is
higher than A12BITB.
8 AUDIO MODE ^ SOUND1 / SOUND2 / MIX
You can select the desired sound mode when playing back an
audio dubbed Mini DV tape.
SOUND1:
Original recorded sound.
SOUND2:
Audio dubbed sound.
MIX:
Original recorded sound and audio-dubbed sound.
NOTES:
● When AAUDIO MODEB is set to AMIXB, both the main and sub
audio will be audible for bilingual tapes.
● To select only the main audio or only the sub audio of bilingual
tapes, set AAUDIO MODEB to ASOUND1B.
REC/PLAY SET UP
8 XP MODE REC AUDIO ^ DOLBY DIGITAL / LINEAR PCM
You can select the audio format when you record a title in XP
mode. When this function is set to ALINEAR PCMB, you can obtain
a high-quality audio sound.
DOLBY DIGITAL:
To record in Dolby Digital format.
LINEAR PCM:
To record in Linear PCM format.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left+
DVM70S_00.book Page 72 Friday, May 6, 2005 12:06 PM
72
EN
SUBSIDIARY SETTINGS
8 2ND AUDIO RECORD ^ OFF / ON
When this function is set to AONB;
If a SAP program is received, the SAP audio is recorded on L/R
tracks. The main audio is not recorded.
If a non-SAP program is received, the main audio is recorded on L/
R tracks.
When this function is set to AOFFB, the SAP audio cannot be recorded.
NOTE:
When the channel is changed on the unit;
● The AMONOB indicator appears on the screen for about 5
seconds if the program is a monaural broadcast.
● The ASTEREOB indicator appears on the screen for about 5
seconds if the program is a stereo broadcast.
● Both ASTEREOB and ASAPB indicators appear when a stereo
program is accompanied by SAP sound.
● Both AMONOB and ASAPB indicators appear when the main audio
on the monaural broadcast is accompanied by SAP sound.
8 JUMP TIME ^ 15 MIN / 30 MIN / 1 HR
You can locate a scene ahead of or behind the currently viewed one
by jumping a selected time interval during playback (or Live Memory
Playback). For details, refer to AJump SearchB (A pg. 26, 40).
DISPLAY SET
8 SUPERIMPOSE ^ AUTO / ON / OFF
When this function is set to AAUTOB, various operational indicators
appear on the TV screen. Messages appear in the selected
language. (A pg. 20)
AUTO:
To superimpose operational indications for approximately five
seconds just after the corresponding operation.
ON:
To turn on superimposed indications.
OFF:
To turn off superimposed indications.
NOTES:
● When you use this unit as the source player for editing, be sure to
set ASUPERIMPOSEB to AOFFB before starting. (A pg. 63)
● When you select AAUTOB, during playback, the operation mode
indicators may be disturbed depending on the type of disc being
used.
8 BLUE BACK ^ OFF / ON
When this function is set to AONB, the TV screen becomes all blue
when receiving a channel not in use.
NOTE:
When you want to receive an unstable channel with poor signals,
set this function to AOFFB.
8 DIMMER ^ BRIGHT / DIMMED
You can change the brightness of the front display panel.
BRIGHT:
Normally select this.
DIMMED:
To dim the front display panel. (Blue lamp on the front display
panel is turned off.)
8 POWER SAVE ^ OFF / ON
When this function is set to AONB, you can reduce the power
consumption while the unit is turned off.
NOTES:
● During Power Save mode ^
^ the front display panel will be turned off.
● Power Save does not work when ^
^ the unit is in the Timer mode.
● It takes some time for the unit to complete initialization after you
turn on the unit power, with AWAKE UPB blinking on the front
display panel.
Page 72Friday, 6 May 2005 12:06
8 ON SCREEN LANGUAGE
This unit offers you the choice to view on-screen messages in 3
different languages.
For details, refer to AOn-screen Language SetB (A pg. 20)
VIDEO IN/OUT
8 MONITOR TYPE ^ 4:3LB / 4:3PS / 16:9AUTO / 16:9FIX
You can select the monitor type depending on the TV used when
you play back DVD VIDEO discs recorded for wide-screen TVs.
For details, refer to AMonitor SetB (A pg. 23).
8 FRONT AUX F-1 ^ VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (F-1)
being used on the front panel.
VIDEO:
To use the [VIDEO] input connector on the front panel.
S-VIDEO:
To use the [S-VIDEO] input connector on the front panel.
8 REAR AUX L-1 ^ VIDEO / S-VIDEO
Select the appropriate mode depending on the connector (L-1)
being used on the rear panel.
VIDEO:
To use the [VIDEO INPUT] connector on the rear panel.
S-VIDEO:
To use the [S-VIDEO INPUT] connector on the rear panel.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right+
DVM70S_00.book Page 73 Friday, May 6, 2005 12:06 PM
SUBSIDIARY SETTINGS
Changing VCR Plus+ Setting
The VCR Plus+ programming system assigns a VCR Plus+ guide
channel to the TV channels and the cable channels. These guide
channel numbers are also called the VCR Plus+ channel codes.
Most TV listings have a section, usually a chart, indicating the
guide channel numbers assigned to each station.
To ensure that VCR Plus+ timer recording operates correctly, it is
necessary to set the “VCR Plus+ Guide Channel” for each station.
If you have moved to a different area or if a broadcasting station’s
channel number has been changed, perform the following steps to
set the correct guide channel number.
NOTES:
● In many instances, the VCR Plus+ guide channel numbers for
cable and broadcast TV stations DO NOT match the channel
number on which it is received by your unit or cable box. Check
your TV listing, or contact your cable supplier for details.
● Many TV stations can be viewed on cable. Check your TV listing,
or contact your cable supplier for details.
● Turn on the unit.
● Turn on the TV and select the video channel (or AV mode).
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
DVD
FGDE
SET UP
Page 73Friday, 6 May 2005 12:06
73
Guide Channel Number Set
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
5
Press D E to select AINITIAL SET UPB, then press G.
Press D E to select ATUNER
SETB, then press G.
DVD VIDEO SET UP
HDD/DVD/DV SET
TUNER SET
INITIAL SET UP
FUNCTION SET UP
CLOCK SET
Press FGD E to select AGUIDE
CH SETB, then press ENTER.
MANUAL CH SET
AUTO CH SET
GUIDE CH SET
11
6
7
Press F G to select AGUIDE CH
SETB, then press ENTER.
SET UP
ENTER
EXIT
SELECT
11
12
13
12
13
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
INITIAL SET UP > GUIDE CH SET
GUIDE CH
1
CABLE CH
--
Press F G to select the Guide
Channel number for the desired
station as shown in the TV
listings. Then press ENTER.
● If you receive your channels
with a cable box and if you have
properly set your Controller,
ACABLE CHB appears in place of ADVD CHB.
SET UP
ENTER
EXIT
SELECT
RETURN
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
8
Press F G to select ADVD CHB, then press ENTER. Press F G
to select the number of the unit’s channel position on which the
Guide Channel Number’s broadcast is received by the unit or
the DBS receiver. Then press ENTER.
● Repeat steps 6 – 8 as necessary.
9
ENTER
EN
Press SET UP to complete the setting.
Guide Channel Number
“Guide Channel (GUIDE CH) Number” refers to the assigned TV
station numbers, according to broadcast area, for the VCR Plus+
timer recording. The Guide Channel Numbers can be found in
most TV listings.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left+
DVM70S_00.book Page 74 Friday, May 6, 2005 12:06 PM
74
EN
SUBSIDIARY SETTINGS
Format A Disc (DVD Deck Only)
Some DVD-RAM/RW discs are unformatted.
Format the disc when you use an unformatted disc or you want to
delete all recordings and data on the disc.
ATTENTION:
● When a disc is formatted, all recordings and data are erased. It
is impossible to restore them.
● Never turn off the unit or disconnect the AC power cord while
ANOW FORMATTING...B is displayed on the TV screen.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-RAM/RW disc to format.
CABLE/DBS
TV
DVD
Format A DVD-RAM Disc
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
3
4
Press SET UP to access the Main Menu screen.
5
6
Press D E to select AHDD/DVD/DV SET UPB, then press G.
Press D E to select ADISC SET
UPB, then press G.
DVD VIDEO SET UP HDD/DVD/DV SET UP FUNCTION SET UP
HDD SET UP
Press FGD E to select
AFORMATB, then press
ENTER. Press D E to select
AOKB, then press ENTER.
Press D E to select
AEXECUTEB, then press
ENTER.
DVD SET UP
DISC SET UP
FINALIZE
CANC. FINALIZ.
INITIAL SET UP
DV SET UP
Video
Vid
eo
FORMAT
SET UP
ENTER
EXIT
SELECT
SELECT WITH @
THEN PRESS [ENTER]
PRESS [SET UP] TO EXIT
Format A DVD-RW Disc
1
Perform steps 1 to 4 of AFormat A DVD-RAM DiscB as above
before continuing.
2
Press FGD E to select AFORMATB, then press ENTER. Press
D E to choose AVR MODEB or AVIDEO MODEB, then press
ENTER when ADISC WILL BE FORMATTEDB appears on the
TV screen.
AVR MODEB:
To be chosen when you want to record, erase, or edit data on
the disc repeatedly.
ENTER
FGDE
SET UP
Page 74Friday, 6 May 2005 12:06
AVIDEO MODEB:
To be chosen when you want to erase all the data on the disc
once played back to record new data, or play back the disc on
other DVD players.
3
Press D E to select AEXECUTEB, then press ENTER.
NOTES:
● It is impossible to format Version 1.0 DVD-RW discs in Video
mode.
● It is impossible to format DVD-R discs.
● All the titles on a disc will be deleted once the disc is formatted
even if they are protected titles. (A pg. 52)
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right+
DVM70S_00.book Page 75 Friday, May 6, 2005 12:06 PM
SUBSIDIARY SETTINGS
Finalize A Disc (DVD Deck Only)
Finalizing DVD-R/RW discs recorded on this unit makes it possible
for the discs to be played back on other DVD players. DVD-RW
discs are finalized in the mode that the discs were formatted,
enabling playback on compatible DVD players.
Title names input in the Library Database Navigation are
registered as title names in the DVD menu. (A pg. 51)
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
● Load a DVD-R/RW disc to finalize.
CABLE/DBS
TV
DVD
EN
75
Finalize A DVD-R/RW Disc
1
Perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74)
before continuing.
2
Press FGD E to select AFINALIZEB, then press ENTER.
● For DVD-R/RW (Video mode) discs, the background selection
screen will appear. Press FGD E to select the desired
background from a selection of 18 backgrounds, then press
ENTER.
3
4
Press D E to select AOKB, then press ENTER.
5
Press SET UP to return to the normal screen.
Upon completing finalization, ACOMPLETEDB appears on the
TV screen. Press ENTER to end.
● Menu screen is cleared.
● Once a DVD-R/RW (Video mode) disc has been finalized, the
displays for original and play list do not appear. Only display for
library appears.
● Once a DVD-RW (VR mode) disc has been finalized, it can be
played on DVD players compatible with VR mode.
Cancel The Finalization Of A DVD-RW Disc
ENTER
FGDE
1
Load a DVD-RW disc to cancel the disc finalization, and
perform steps 1 to 4 of AFormat A DVD-RAM DiscB (A pg. 74)
before continuing.
2
3
4
Press FGD E to select ACANC. FINALIZ.B, then press ENTER.
5
Press SET UP to return to the normal screen.
Press D E to select AEXECUTEB, then press ENTER.
Upon completing cancellation of finalization, ACANCELLATION
COMPLETEDB appears on the TV screen. Press ENTER to
end.
● When the disc finalization is canceled, the mode in which the
disc was formatted is restored, making the disc recordable.
(A pg. 9, 74)
SET UP
Before finalizing
● It is possible to record on a blank space.
● It is possible to enter title names. (A pg. 51)
● It is possible to delete titles. (A pg. 52)
● It is impossible to overwrite recorded areas of DVD-R discs.
● Available recording capacity does not increase even if a recorded
title is deleted from a DVD-R disc.
● It is impossible to record or edit DVD-R/RW discs recorded on
other devices even if they have not been finalized.
After finalizing (For DVD-R/RW (Video mode) discs)
● Video and audio that have been recorded by then are recorded in
conformity to the DVD Video standard, enabling you to play back
the discs as DVD VIDEO discs.
● Although DVD-R/RW discs finalized on this unit become playable
on DVD players compatible with DVD-R/RW discs, some discs
still may not play, for which JVC cannot take responsibility.
● Marked points marked before finalizing will be deleted, and titles
will be divided automatically into AchaptersB approximately every
5 minutes. (A pg. 27)
● Depending on the DVD players and DVD-R/RW discs used, and
on the conditions of recording, it may not be possible to play back
the discs. In this case, play back the discs on this unit.
● Additional recordings become impossible.
Page 75Friday, 6 May 2005 12:06
Filename [DVM70S_13Subsidiary.fm]
DVM70S_00.book Page 76 Friday, May 6, 2005 12:06 PM
76
EN
Masterpage:Left+
SUBSIDIARY SETTINGS
Scan Mode Set (HDD & DVD Deck Only)
If you connect the unit and TV with Component Video Connection
(A pg. 18), you can select the scan mode from two modes:
Interlaced scan mode which is used in the conventional TV
system, and Progressive scan mode which enables reproduction
of higher-quality images.
Tray Lock (DVD Deck Only)
You can lock the disc tray to prohibit the unwanted disc ejection by
children.
● Turn off the unit.
8 Interlaced scan
M
In the conventional video system, a picture is shown on the display
monitor in two halves. The Interlaced scan system places lines of
the second half of the picture in-between lines of the first half of the
picture.
o
8 Progressive scan
Progressive scan displays all the horizontal lines of a picture at
one time, as a single frame. This system can convert the interlaced
video from DVD into progressive format for connection to a
progressive display. It dramatically increases the vertical
resolution.
ATTENTION:
Your TV needs to be compatible with Progressive.
To lock tray
While the unit is turned off, press and hold o, then press M on the
unit. ALOCKB appears on the front display panel and the disc tray is
locked.
To unlock tray
While the unit is turned off, press and hold o, then press M on the
unit. AUNLOCKB appears on the front display panel.
● Turn on the unit.
● Turn on the TV and select the AV mode.
● Slide the TV/CABLE/DBS/DVD switch to DVD.
CABLE/DBS
TV
HDD
DV
DVD
DVD
Mode Lock
When the unit is turned on, press and hold ENTER on the remote
control for more than 5 seconds. ALOCKB appears on the front
display panel.
● No buttons will function and playback and recording will not be
interrupted.
● When the unit is in the stop mode, all buttons will not function
except R and I.
To cancel Mode Lock, press and hold ENTER again for more than
5 seconds.
NOTE:
It is also possible to use Mode Lock during Repeat Playback
(A pg. 29).
Last Function Memory
PROGRESSIVE SCAN
1
Press HDD or DVD so that the HDD or DVD lamp lights up on
the unit.
2
Press PROGRESSIVE SCAN for 3 or more seconds.
● Video output indicator (q) lights on the front display panel if
Progressive scan mode has been established. (A pg. 14)
● Each press of PROGRESSIVE SCAN for 3 or more seconds
switches the scan mode.
NOTES:
● Interlaced scan mode is the setting at your purchase.
● Interlaced scan mode might be suitable depending on video
material.
● Scan mode cannot be set while menu screen is displayed.
● When the Progressive scan mode is engaged, no video signal is
output from [S-VIDEO OUTPUT] connector and [VIDEO/AUDIO
OUTPUT] connectors.
Page 76Friday, 6 May 2005 12:06
When the power plug is disconnected from unit or when power
failure occurs, your settings for the following functions are kept in
the memory. These settings will resume when the unit is turned on
again.
● Input selection (channel or auxiliary input; L-1, F-1 or DV)
● Recorder selection (The last selected deck is memorized.)
● Country setting (A pg. 12)
● Recording speed (A pg. 34, 37)
● Mode settings (A pg. 70 – 72)
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right0
DVM70S_00.book Page 77 Friday, May 6, 2005 12:06 PM
TROUBLESHOOTING
Before requesting service for a problem, use this chart and see if
you can solve the trouble yourself. Small problems are often easily
solved, and this can save you the trouble of sending your unit off
for repair.
Initializing (DVD Deck Only)
Malfunction occurs on the unit.
] Press A to turn off the unit, press and hold A, then press o
for two seconds or more.
General
No power is supplied to the unit.
●
The AC power plug is disconnected from the AC outlet.
] Connect the AC power plug to the AC outlet securely.
(A pg. 18)
The remote control does not work properly.
] Remove the batteries, wait for 5 minutes or more, then load the
butteries again.
● The setting of the remote control code is inappropriate.
] Set the same remote control code (1, 2, 3, or 4) on both the unit
and the remote control. (A pg. 67)
● The batteries are discharged.
] Replace the dead batteries with new ones.
Dubbing from the external equipment is not possible.
●
]
●
]
●
]
The source (another video recorder, camcorder) has not been
properly connected.
Confirm that the source is properly connected.
All necessary power switches have not been turned on.
Confirm that all units’ power switches are turned on.
The setting of the input channel position is inappropriate.
Select the input channel position (AF-1B or AL-1B) that
corresponds to the input terminal connected to the external
equipment. (A pg. 63)
The on-screen display superimposed on the program played
back/received on this unit is recorded when you dub the
program to an external recording equipment.
] Set ASUPERIMPOSEB to AOFFB. (A pg. 72)
The unit does not operate.
●
●
There are cases when the operation is prohibited on the disc.
Lightning or static electricity may cause malfunction of the unit.
] Press A to turn the power off, then press the button again to
turn the power on.
The remote control of a JVC TV will not operate the unit.
●
The setting of the remote control code is inappropriate.
] To operate the unit using a JVC TV remote control, set the
remote control code of the unit to A1B (Default: A3B). (A pg. 67)
Page 77Friday, 6 May 2005 12:06
EN
77
Playback (DVD Deck)
The DVD deck cannot be operated.
● The DVD deck is not selected.
] Press DV/HDD/DVD on the unit repeatedly or DVD on the
remote so that the DVD lamp lights up on the unit.
Images do not appear on the TV screen.
● The TV receiver’s channel selector is not set to the AV mode.
] Set the TV to its AV mode.
● When interlace scanned program is played back, progressive
scan mode is selected.
] Press and hold PROGRESSIVE SCAN until q disappears
from the front display panel. (A pg. 76)
Playback does not start or stop immediately after playback is
started by pressing I.
On the front display panel, ANO DISCB appears.
● The disc is loaded upside down.
] Place the disc on the disc tray with the playback surface facing
down. (A pg. 10)
● A disc not being compatible with the unit is loaded.
] Load a playable disc on the unit. (A pg. 7)
● A dirty disc is loaded.
] Clean the disc. (A pg. 11)
● Defective disc is loaded.
] Replace the warped or scratched disc with a normal one.
Images are blurred or distorted when you start High-Speed
Search.
] Images are blurred or distorted at the point where the playback
speed changes and this is not a malfunction of the unit.
Playback does not start.
] Playback does not start for approximately 30 seconds after
recording is stopped and this is not a malfunction of the unit.
Playback does not start when you select a title or a chapter.
●
The Parental Lock is engaged and the disc is rated higher than
the set level.
] Release the Parental Lock temporarily or change the set level.
(A pg. 33)
Playback (HDD Deck)
The HDD deck cannot be operated.
●
The HDD deck is not selected.
] Press DV/HDD/DVD on the unit repeatedly or HDD on the
remote so that the HDD lamp lights up on the unit.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left+
DVM70S_00.book Page 78 Friday, May 6, 2005 12:06 PM
78 EN TROUBLESHOOTING
Playback (DV Deck)
Recording (HDD Deck)
The DV deck cannot be operated.
TV broadcasts cannot be recorded.
●
●
The DV deck is not selected.
] Press DV/HDD/DVD on the unit repeatedly or DV on the remote
so that the DV lamp lights up on the unit.
The tape will not rewind or fast-forward.
●
The tape is already fully rewound or fast-forwarded.
] Check the cassette.
The playback picture does not appear while the tape is
running.
AL-1B or AF-1B has been selected as the input mode.
] Set to the desired channel.
Camcorder recording is not possible.
●
The camcorder has not been properly connected.
] Confirm that the camcorder is properly connected.
● The input mode is not correct.
] Set the input mode to AF-1B. (A pg. 62)
Recording (DV Deck)
●
The TV is not set to the AV mode.
] Set the TV to the AV mode.
Noise appears during visual search.
●
This is normal.
The playback picture is blurred or interrupted while TV
broadcasts are clear or AUSE CLEANING CASSETTEB
message appears on the screen.
● The video heads may be dirty.
] Use a dry cleaning cassette M-DV12CL, or consult your JVC
dealer.
Recording (DVD Deck)
The desired program cannot be recorded.
●
The channel position does not correspond to that in the
receiving area.
] Set the correct channel position for the receiving broadcast.
(A pg. 22)
Recording cannot be made.
●
No disc or a disc not being compatible with the unit is loaded.
] Load a recordable disc on the unit. (A pg. 7)
● The disc loaded is not formatted.
] Format the disc. (A pg. 74)
● A finalized DVD-R disc is loaded.
] Recording cannot be made on finalized discs. Load a
recordable disc on the unit.
● The disc is full or does not have enough space for the title to be
recorded.
] Clear unnecessary titles on the disc or load a blank disc.
(A pg. 52)
● The DVD-RAM disc loaded has had its protect tab slid to the
protect position.
] Release the protect tab. (A pg. 10)
Page 78Friday, 6 May 2005 12:06
During recording, the tape does not run. The DV recording
lamp lights up on the unit.
● The unit is in the Record Pause mode.
] Press I to resume recording.
Recording cannot be done.
●
There is no cassette loaded, or the cassette loaded has had its
erase protection switch set to ASAVEB.
] Insert a Mini DV cassette, or set the erase protection switch set
to ARECB.
Camcorder recording is not possible.
●
The camcorder has not been properly connected.
] Confirm that the camcorder is properly connected.
● The input mode is not correct.
] Set the input mode to AF-1B or ADVB.
The tape is automatically rewound, then the unit is shut off.
● The end of the tape was reached during recording.
] The program may not have been recorded in its entirety. Next
time make sure you have enough time on the tape to record the
entire program.
Audio dubbing is not possible.
●
ADV AUDIO RECB had been set to A16BITB at the original
recording.
] Set ADV AUDIO RECB to A12BITB at the original recording.
● The tape speed had been set to LP at the original recording.
] Set the tape speed to SP at the original recording.
Monitoring the audio dubbed sound is not possible during
audio dubbing.
] This is normal. Monitor the sound using the connected devices.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right+
DVM70S_00.book Page 79 Friday, May 6, 2005 12:06 PM
TROUBLESHOOTING
EN
79
Timer Recording (HDD & DVD Deck)
Other Problems
Timer programming cannot be made.
The image of the TV broadcast appears distorted on the TV
screen.
●
Date and time is not correct.
] Set date and time correctly. (A pg. 21)
● Timer recording is in progress.
] Timer programming can’t be performed while a timer recording
is in progress. Wait until it finishes.
Timer programming recording does not start.
● Date and time is not correct.
] Set date and time correctly. (A pg. 21)
VCR Plus+ Timer Programming cannot be made.
●
Date and time set on the unit is not correct.
] Set date and time correctly. (A pg. 21)
● The channel position does not correspond to that in the
receiving area.
] Set the correct channel position for the receiving broadcast.
(A pg. 22)
For RF/AV/S-video connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights off on the front display panel.
For component video connection
] Press PROGRESSIVE SCAN for 3 or more seconds so that the
Video output indicator (q) lights up on the front display panel.
Whistling or howling is heard from the TV during camcorder
recording.
● The camcorder’s microphone is too close to the TV.
] Position the camcorder so its microphone is away from the TV.
● The TV’s volume is too high.
] Turn the TV’s volume down.
When scanning channels, some of them are skipped over.
●
The VCR Plus+ system does not timer-record properly.
Those channels have been designated to be skipped.
] If you need the skipped channels, restore them. (A pg. 22)
● The unit’s channel positions have been set incorrectly.
] Refer to AChanging VCR Plus+ SettingB (A pg. 73) and
reperform the procedure.
●
On the front display panel, A– –:– –B appears.
The channel cannot be changed.
Recording or RetroActive Recording* is in progress.
] Press W to pause recording, change the channel, then press I
to resume recording.
●
Power failure occurred.
] Set date and time correctly. (A pg. 21)
APROGRAM FULLB appears on the TV screen during timer
programming.
●
16 programs have already been timer programmed.
] Clear unnecessary programs on the unit, then try timer
programming again. (A pg. 49)
The disc space does not increase when recorded titles are
cleared.
●
The PC’s data recorded on a DVD-RAM drive cannot be
cleared on this unit.
] Format the disc. (When the disc is soiled, wipe the disc with a
soft dry cloth before formatting.) (A pg. 11, 74)
* HDD deck only
Channel settings that were made manually seem to have
changed or disappeared.
●
After the manual settings were made, Auto Channel Set was
performed.
] Perform AManual Clock SetB (A pg. 21).
Even though Auto or Semiauto Clock Set has been
performed, the clock is incorrect.
●
The clock setting data received from the host channel is
incorrect.
] Select a different host channel during ASemiauto Clock SetB
(A pg. 21), or perform AManual Clock SetB (A pg. 21).
Malfunction occurs and the unit cannot be power off.
] Reset the unit by disconnecting the AC power plug from the AC
outlet and connect again.
Buttons and controls do not function at all.
● Mode Lock is activated.
] Press and hold ENTER for more than 5 seconds to cancel
Mode Lock. Or disconnect the power cord and connect again.
Page 79Friday, 6 May 2005 12:06
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left+
DVM70S_00.book Page 80 Friday, May 6, 2005 12:06 PM
80 EN TROUBLESHOOTING
On-screen Message (HDD & DVD Deck Only)
DISC NOT REGISTERED IN THE LIBRARY
REGISTER DISC?
● A disc that is not registered in the library has been inserted.
Register the disc as necessary. (A pg. 55)
INSERT DISC XXXX
● Appears when a title that has been selected in the library is not
contained in the loaded disc.
CAN NOT RECORD OR MAKE PLAY LIST
DELETE UNWANTED TITLES
● Recording and/or editing cannot be performed.
● The number of titles exceeds 99.
● The number of play lists exceeds 99.
SET CLOCK BEFORE TIMER PROGRAMMING
● To set the timer program, the clock must be set in advance.
(A pg. 21)
PROGRAM FULL
DELETE UNWANTED TIMER PROGRAMS
● You can program this unit to timer-record as many as 32
programs. To program more, you need to cancel a timer program
already set. (A pg. 49)
DISC NOT LOADED
● Operation has been attempted when a disc is not loaded, or
UNREADABLE DISC
CHECK DISC
● When an incompatible disc is loaded, I has been pressed.
(A pg. 8)
COULD NOT FORMAT THE DISC
CHECK THE DISC
● Formatting is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (A pg. 11, 74)
CAN NOT FINALIZE THIS DISC
● Finalizing is not complete since the disc may be dirty or
damaged. Take out the disc, clean it and retry. (A pg. 11, 75)
CAN NOT CANCEL FINALIZATION OF THIS DISC
● Canceling disc finalization is not complete since the disc may be
dirty or damaged. Take out the disc, clean it and retry. (A pg. 11,
75)
PRESS [STOP] AGAIN TO STOP RECORDING
● During Live Memory playback, o has been pressed. (A pg. 44)
TIMER RECORDING COMPLETED
● Timer recording has finished during Live Memory playback.
PLAYBACK WILL STOP
THEN TIMER RECORDING WILL START
● Timer recording finished during Live Memory playback, then the
next timer recording is about to begin while playback continues.
loaded upside down. (A pg. 10)
DISC NOT RECORDABLE
INSERT RECORDABLE DISC
● When a playback-only disc or a finalized disc is loaded, R has
been pressed. (A pg. 7)
COPY PROHIBITED
CAN NOT RECORD
● An attempt has been made to record copy-protected contents.
● An attempt has been made to record copy-once contents on a
disc that is not CPRM compatible, such as DVD-R.
PLUSCODE NO. ERROR
CONFIRM PLUSCODE NO. THEN RETRY
COPY PROHIBITED
CAN NOT PLAY
● An invalid PlusCode number has been input. (A pg. 46)
● The unit has detected invalid contents at the start or in the middle
GUIDE PROGRAM IS NOT SET
SET GUIDE PROGRAM THEN RETRY
● To set the timer program using the VCR Plus+ system, the Guide
Channel Number must be set in advance. (A pg. 73)
of playback.
THE i.LINK DEVICE THAT YOU HAVE CONNECTED IS NOT
RECOGNIZED
MAKE SURE THAT THE DEVICE IS CONNECTED PROPERLY
AND POWERED ON
CAN NOT SET VCR PLUS+ TIMER PROGRAMMING DURING
TIMER RECORDING OR INSTANT TIMER RECORDING
● An attempt has been made to start DV dubbing when a digital
● Appears when you tried to input a PlusCode number during timer
● Check the connection. (A pg. 60)
recording or instant timer recording.
REGION CODE ERROR
CHECK DISC
● A disc loaded cannot be played back on this unit since the region
number of the disc does not match that of the unit. (A pg. 8)
Page 80Friday, 6 May 2005 12:06
video camera is not properly connected to the unit.
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right0
DVM70S_00.book Page 81 Friday, May 6, 2005 12:06 PM
APPENDIX
Language Code List
AA
Afar
IK
Inupiak
RN
Kirundi
AB
Abkhazian
IN
Indonesian
RO
Rumanian
AF
Afrikaans
IS
Icelandic
RU
Russian
AM
Ameharic
IW
Hebrew
RW
Kinyarwanda
AR
Arabic
JI
Yiddish
SA
Sanskrit
AS
Assamese
JW
Javanese
SD
Sindhi
AY
Aymara
KA
Georgian
SG
Sangho
AZ
Azerbaijani
KK
Kazakh
SH
Serbo-Croatian
BA
Bashkir
KL
Greenlandic
SI
Singhalese
BE
Byelorussian
KM
Cambodian
SK
Slovak
BG
Bulgarian
KN
Kannada
SL
Slovenian
BH
Bihari
KO
Korean (KOR)
SM
Samoan
BI
Bislama
KS
Kashmiri
SN
Shona
BN
Bengali, Bangla
KU
Kurdish
SO
Somali
BO
Tibetan
KY
Kirghiz
SQ
Albanian
BR
Breton
LA
Latin
SR
Serbian
CA
Catalan
LN
Lingala
SS
Siswati
CO
Corsican
LO
Laothian
ST
Sesotho
CS
Czech
LT
Lithuanian
SU
Sundanese
CY
Welsh
LV
Latvian, Lettish
SW
Swahili
DZ
Bhutani
MG
Malagasy
TA
Tamil
EL
Greek
MI
Maori
TE
Telugu
EO
Esperanto
MK
Macedonian
TG
Tajik
ET
Estonian
ML
Malayalam
TH
Thai
EU
Basque
MN
Mongolian
TI
Tigrinya
FA
Persian
MO
Moldavian
TK
Turkmen
FJ
Fiji
MR
Marathi
TL
Tagalog
FO
Faroese
MS
Malay (MAY)
TN
Setswana
FY
Frisian
MT
Maltese
TO
Tonga
GA
Irish
MY
Burmese
TR
Turkish
GD
Scots Gaelic
NA
Nauru
TS
Tsonga
GL
Galician
NE
Nepali
TT
Tatar
GN
Guarani
OC
Occitan
TW
Twi
GU
Gujarati
OM
(Afan) Oromo
UK
Ukrainian
HA
Hausa
OR
Oriya
UR
Urdu
HI
Hindi
PA
Panjabi
UZ
Uzbek
HR
Croatian
PL
Polish
VI
Vietnamese
HU
Hungarian
PS
Pashto, Pushto
VO
Volapuk
HY
Armenian
PT
Portuguese
WO
Wolof
IA
Interlingua
QU
Quechua
XH
Xhosa
IE
Interlingue
RM
Rhaeto-Romance
Page 81Friday, 6 May 2005 12:06
YO
Yoruba
ZU
Zulu
EN
81
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Left+
DVM70S_00.book Page 82 Friday, May 6, 2005 12:06 PM
82 EN APPENDIX
Country/Area Code List for Parental Lock
AD
Andorra
CK
Cook Islands
GN
Guinea
AE
United Arab Emirates
CL
Chile
GP
Guadeloupe
AF
Afghanistan
CM
Cameroon
GQ
Equatorial Guinea
AG
Antigua and Barbuda
CN
China
GR
Greece
AI
Anguilla
CO
Colombia
GS
South Georgia and the South
Sandwich Islands
AL
Albania
CR
Costa Rica
GT
Guatemala
AM
Armenia
CU
Cuba
GU
Guam
AN
Netherlands Antilles
CV
Cape Verde
GW
Guinea-Bissau
AO
Angola
CX
Christmas Island
GY
Guyana
AQ
Antarctica
CY
Cyprus
HK
Hong Kong
AR
Argentina
CZ
Czech Republic
HM
Heard Island and McDonald
Islands
AS
American Samoa
DE
Germany
HN
Honduras
AT
Austria
DJ
Djibouti
HR
Croatia
AU
Australia
DK
Denmark
HT
Haiti
AW
Aruba
DM
Dominica
HU
Hungary
AZ
Azerbaijan
DO
Dominican Republic
ID
Indonesia
BA
Bosnia and Herzegovina
DZ
Algeria
IE
Ireland
BB
Barbados
EC
Ecuador
IL
Israel
BD
Bangladesh
EE
Estonia
IN
India
BE
Belgium
EG
Egypt
IO
British Indian Ocean Territory
BF
Burkina Faso
EH
Western Sahara
IQ
Iraq
BG
Bulgaria
ER
Eritrea
IR
Iran (Islamic Republic of)
BH
Bahrain
ES
Spain
IS
Iceland
BI
Burundi
ET
Ethiopia
IT
Italy
BJ
Benin
FI
Finland
JM
Jamaica
BM
Bermuda
FJ
Fiji
JO
Jordan
BN
Brunei Darussalam
FK
Falkland Islands (Malvinas)
JP
Japan
BO
Bolivia
FM
Micronesia
(Federated States of)
KE
Kenya
BR
Brazil
FO
Faroe Islands
KG
Kyrgyzstan
BS
Bahamas
FR
France
KH
Cambodia
BT
Bhutan
FX
France, Metropolitan
KI
Kiribati
BV
Bouvet Island
GA
Gabon
KM
Comoros
BW
Botswana
GB
United Kingdom
KN
Saint Kitts and Nevis
BY
Belarus
GD
Grenada
KP
Korea, Democratic People’s
Republic of
BZ
Belize
GE
Georgia
KR
Korea, Republic of
CA
Canada
GF
French Guiana
KW
Kuwait
CC
Cocos (Keeling) Islands
GH
Ghana
KY
Cayman Islands
CF
Central African Republic
GI
Gibraltar
KZ
Kazakhstan
CG
Congo
GL
Greenland
LA
Lao People’s Democratic
Republic
CH
Switzerland
GM
Gambia
LB
Lebanon
CI
Côte d’Ivoire
Page 82Friday, 6 May 2005 12:06
Filename [DVM70S_13Subsidiary.fm]
Masterpage:Right+
DVM70S_00.book Page 83 Friday, May 6, 2005 12:06 PM
APPENDIX
LC
Saint Lucia
NU
Niue
SZ
LI
Liechtenstein
NZ
New Zealand
TC
Turks and Caicos Islands
LK
Sri Lanka
OM
Oman
TD
Chad
EN
Swaziland
LR
Liberia
PA
Panama
TF
French Southern Territories
LS
Lesotho
PE
Peru
TG
Togo
LT
Lithuania
PF
French Polynesia
TH
Thailand
LU
Luxembourg
PG
Papua New Guinea
TJ
Tajikistan
LV
Latvia
PH
Philippines
TK
Tokelau
LY
Libyan Arab Jamahiriya
PK
Pakistan
TM
Turkmenistan
MA
Morocco
PL
Poland
TN
Tunisia
MC
Monaco
PM
Saint Pierre and Miquelon
TO
Tonga
MD
Moldova, Republic of
PN
Pitcairn
TP
East Timor
MG
Madagascar
PR
Puerto Rico
TR
Turkey
MH
Marshall Islands
PT
Portugal
TT
Trinidad and Tobago
ML
Mali
PW
Palau
TV
Tuvalu
MM
Myanmar
PY
Paraguay
TW
Taiwan
MN
Mongolia
QA
Qatar
TZ
Tanzania, United Republic of
MO
Macau
RE
Réunion
UA
Ukraine
MP
Northern Mariana Islands
RO
Romania
UG
Uganda
MQ
Martinique
RU
Russian Federation
UM
United States Minor Outlying
Islands
MR
Mauritania
RW
Rwanda
US
United States
MS
Montserrat
SA
Saudi Arabia
UY
Uruguay
MT
Malta
SB
Solomon Islands
UZ
Uzbekistan
MU
Mauritius
SC
Seychelles
VA
Vatican City State (Holy See)
MV
Maldives
SD
Sudan
VC
Saint Vincent and the
Grenadines
MW
Malawi
SE
Sweden
VE
Venezuela
MX
Mexico
SG
Singapore
VG
Virgin Islands (British)
MY
Malaysia
SH
Saint Helena
VI
Virgin Islands (U.S.)
MZ
Mozambique
SI
Slovenia
VN
Viet Nam
NA
Namibia
SJ
Svalbard and Jan Mayen
VU
Vanuatu
NC
New Caledonia
SK
Slovakia
WF
Wallis and Futuna Islands
NE
Niger
SL
Sierra Leone
WS
Samoa
NF
Norfolk Island
SM
San Marino
YE
Yemen
NG
Nigeria
SN
Senegal
YT
Mayotte
NI
Nicaragua
SO
Somalia
YU
Yugoslavia
NL
Netherlands
SR
Suriname
ZA
South Africa
NO
Norway
ST
Sao Tome and Principe
ZM
Zambia
NP
Nepal
SV
El Salvador
ZR
Zaire
NR
Nauru
SY
Syrian Arab Republic
ZW
Zimbabwe
Page 83Friday, 6 May 2005 12:06
83
Filename [DVM70S_142RS232.fm]
Masterpage:Left0
DVM70S_00.book Page 84 Friday, May 6, 2005 12:06 PM
84
EN
RS-232C INTERFACE
RS-232C Interface – Command Table –
0
Lower OrderN
Higher OrderQ
1
0
2
3
4
5
6
7
8
9
Cassette
Out
A
B
ACK
NAK
C
D
E
F
1
2
3
PLAY
STOP
4
STILL
5
6
7
8
9
A
Standby
ON
Standby
OFF
Eject
B
FF
Fwd Shtl
REW
Rev Shtl
DateData
Sense
C
Rec
D
Status
Sense
Tc Data
Sense
ClockData
Sense
Rec
Pause
CTL
Data
Sense
JVCStatus
Sense
E
F
Command
Target
Rec/Dub
Request
Vtr Ind
RS-232C Interface – Specifications –
● 9PIN D-Sub
1
5
9
6
PIN No.
Signal
Operation
Direction of
signal
2
RxD
Receive data
HDD/DVDOPC
3
TxD
Transmit data
HDD/DVDNPC
5
GND
Signal grounding
Mode
Character length
Parity check
Start bit
Stop bit
Data rate
Bit configuration
D0
Starting bit
:
:
:
:
:
:
D1
Non-synchronous
8 bits
None
1
1
9600bps
D2
D3
D4
D5
D6
D7
Stopping bit
NOTES:
● When using the Serial Command Connector, the cable to be used should be a RS-232C interface cable (straight type).
● It takes about 10 seconds for the communication to be established after turning on the unit.
Page 84
Friday, 6 May 2005 12:06
Filename [DVM70S_142RS232.fm]
Masterpage:Right+
DVM70S_00.book Page 85 Friday, May 6, 2005 12:06 PM
RS-232C INTERFACE
RS-232C Interface – Command –
● Operation Commands
Commands for operating functions such as PLAY and REC on the
HDD/DVD/Mini DV deck.
Command
Description
3A
Plays the selected deck.
3F
Stops the selected deck. Resume will be cleared
when this is pressed while in the Stop mode.
(HDD/DVD Deck)
Rec Request will be cleared.
4F
Switches the selected deck to the Still mode.
AO
Power On
A1
Power Off
A3
Eject: HDD/DVD Deck: Opens/Closes tray.
Mini DV Deck: Removes cassette.
AB
FF: HDD/DVD Deck: Functions only during
playback. Activates forward search. Forward
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Fast forward. Search Fwd during
playback.
AC
B5
85
● System Commands
Commands relating to RS-232C control system.
Command
Description
0A
ACK: A return command issued when a defined
command is received.
0B
NAK: A return command issued when an
undefined or possibly nonexistent command is
received.
FB
VTR Ind: A command for checking whether the
connected device is a VTR.
● Response Commands
Commands for acquiring information such as deck status.
Command
Description
03
Cassette Out: Issued by the Mini DV deck when
the cassette is ejected after ejecting is performed.
BE
Date Sense: For acquiring the currently
configured year, month and day.*
BF
Time Sense: For acquiring the currently
configured hour, minute and second.*
D7
Status Sense: For acquiring the deck
information.*
REW: HDD/DVD Deck: Functions only during
playback. Activates reverse search. Reverse
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Rewind. Search Rev during
playback.
D8
TC Data Sense: For acquiring the total remaining
time in the current recording mode when there is
a media in the selected deck.*
D9
CTL Data Sense: For acquiring the lapse counter
when there is a media in the selected deck.*
Fwd Shtl: HDD/DVD Deck: Functions only during
playback. Activates forward search. Forward
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Fast forward. Search Fwd during
playback.
DD
JVC Data Sense: Returns data from the unit.*
B6
Rev Shtl: HDD/DVD Deck: Functions only during
playback. Activates reverse search. Reverse
search speed increases in step of 2x, 4x, 8x and
16x via each operation.
Mini DV Deck: Rewind. Search Rev during
playback.
CA
Rec: Starts recording at the selected deck when
a Rec Request is received.
CB
Rec Pause: Switches the selected deck to the
Rec Pause mode when a Rec Request is
received.
F0
Command Target: VTR1: For selecting Mini DV
deck.
HDD1: For selecting HDD deck.
DVD1: For selecting DVD deck.
FA
Rec Request: For issuing approval for recording.
This can be cleared using STOP.
Page 85
EN
* See pages 86 and 87 for data format.
Friday, 6 May 2005 12:06
Filename [DVM70S_142RS232.fm]
Masterpage:Left+
DVM70S_00.book Page 86 Friday, May 6, 2005 12:06 PM
86
EN
RS-232C INTERFACE
Date Data Sense
For acquiring the currently configured year, month and day in ASCII codes.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
Yr (Tens)
Yr (Ones)
Mth (Tens)
Mth (Ones)
Day (Tens)
Day (Ones)
BE
3*
3*
3*
3*
3*
3*
E.g. (2004.11.17)
30
34
31
31
31
37
Date Sense
When the current time is not set, the value is fixed as “—” (0x2D).
Time Data Sense
For acquiring the currently configured hour, minute and second in ASCII codes.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
Hr (Tens)
Hr (Ones)
Min (Tens)
Min (Ones)
Sec (Tens)
Sec (Ones)
BF
3*
3*
3*
3*
3*
3*
E.g. (12:34:56)
31
32
33
34
35
36
Time Sense
When the current time is not set, the value is fixed as “—” (0x2D).
Status Data Sense
D7 STATUS SENSE
1byte
DV
2byte
HDD/DVD
DV
3byte
HDD/DVD
DV
HDD/DVD
bit7
1 (Fixed)
1 (Fixed)
Video EE
Video EE
0 (Fixed)
0 (Fixed)
bit6
0 (Fixed)
0 (Fixed)
Audio EE
Audio EE
0 (Fixed)
Timer REC
(Including
PAUSE)
bit5
0 (Fixed)
0 (Fixed)
Video Mute
Video Mute
0 (Fixed)
0 (Fixed)
bit4
Record
Forbidden
Record
Forbidden
Audio Mute
Audio Mute
0 (Fixed)
0 (Fixed)
bit3
Cassette Not
Inserted
Cassette Not
Inserted
Occurrence of
abnormality in VTR
Occurrence of
abnormality in VTR
0 (Fixed)
0 (Fixed)
bit2
0 (Fixed)
0 (Fixed)
Occurrence of moisture
condensation in VTR
Occurrence of moisture
condensation in VTR
0 (Fixed)
During Repeat
Playback (Including
PAUSE)
bit1
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit0
Occurrence of
DV EMG
Occurrence of
EMG
0 (Fixed)
0 (Fixed)
D7 STATUS SENSE
4byte
DV
5byte
HDD/DVD
DV
HDD/DVD
bit7
During PLAY
During PLAY
During PAUSE (Set to 1 simultaneously
with ADuring PLAYB in STILL mode, set
to 1 simultaneously with ADuring RECB
in REC PAUSE mode.)
During PAUSE (Set to 1 simultaneously
with ADuring PLAYB in STILL mode, set
to 1 simultaneously with ADuring RECB
in REC PAUSE mode.)
bit6
During FF
During FF
0 (Fixed)
0 (Fixed)
bit5
During REW
During REW
During Reverse Shuttle Search
(Excluding STILL)
0 (Fixed)
bit4
During STOP
During STOP
During Forward Shuttle Search
(Excluding STILL)
0 (Fixed)
bit3
During STANDBY
(Unit Power Off)
During STANDBY
(Unit Power Off)
SPEED CODE 3
0 (Fixed)
bit2
During CASSETTE
EJECT
0 (Fixed)
SPEED CODE 2
0 (Fixed)
bit1
During REC
During REC
SPEED CODE 1
0 (Fixed)
bit0
During Audio Dub
During Audio Dub
SPEED CODE 0
0 (Fixed)
Page 86
Friday, 6 May 2005 12:06
Filename [DVM70S_142RS232.fm]
Masterpage:Right+
DVM70S_00.book Page 87 Friday, May 6, 2005 12:06 PM
RS-232C INTERFACE
TC Data Sense
EN
87
For acquiring the remaining time in the current recording mode in hours, minutes and seconds for HDD/DVD,
and hours and minutes for Mini DV.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
7th Byte
8th Byte
Hr (Tens)
Hr (Ones)
Min (Tens)
Min (Ones)
Sec (Tens)
Sec (Ones)
Frame
(Tens)
Frame
(Ones)
D8
3*
3*
3*
3*
3*
3*
3*
3*
E.g. (01:23:45)
30
3
32
33
34
35
30
30
TC Data Sense
E.g.: When remaining time is 1 hr 23 min 45 sec.
Mini DV (hr and min only)
HDD/DVD (hr, min and sec only)
Frame is fixed as 0.
CTL Data Sense
For acquiring lapse counter of selected deck in hours, minutes and seconds.
1st Byte
2nd Byte
3rd Byte
4th Byte
5th Byte
6th Byte
7th Byte
8th Byte
Hr (Tens)
Hr (Ones)
Min (Tens)
Min (Ones)
Sec (Tens)
Sec (Ones)
Frame
(Tens)
Frame
(Ones)
D9
3*
3*
3*
3*
3*
3*
3*
3*
Eg. (01:23:45)
30
31
32
33
34
35
30
30
CTL Data Sense
E.g.: When time lapse counter is 1 hr 23 min 45 sec.
JVC Data Sense
DD JVC
SENSE
1byte
DV
2byte
HDD/DVD
DV
HDD/DVD
3byte
DV
4byte
HDD/DVD
DV
HDD/DVD
bit7
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
1 (Fixed)
1 (Fixed)
bit6
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
1 (Fixed)
1 (Fixed)
bit5
0 (Fixed)
0 (Fixed)
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit4
During
Playback of LP
Recorded Tape
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit3
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit2
0 (Fixed)
0 (Fixed)
0 (Fixed)
0 (Fixed)
During Audio
Dub (Including
PAUSE)
0 (Fixed)
0 (Fixed)
0 (Fixed)
bit1
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
During Insert
(Including
PAUSE)
0 (Fixed)
0 (Fixed)
0 (Fixed)
During REC
(Including
PAUSE)
During REC
(Including Timer
REC, Normal REC,
OTR, RECLINK
REC, DV AUTO
REC and also REC
PAUSE.)
0 (Fixed)
0 (Fixed)
bit0
Page 87
1 (Fixed)
1 (Fixed)
0 (Fixed)
0 (Fixed)
Friday, 6 May 2005 12:06
Filename [DVM70S_142RS232.fm]
Masterpage:Left0
DVM70S_00.book Page 88 Friday, May 6, 2005 12:06 PM
88
EN
SPECIFICATIONS
GENERAL
VIDEO/AUDIO (HDD Deck)
Power requirement
AC 120 VH, 60 Hz
Video recording compression system
MPEG2 (VBR)
Power consumption
Power on: 49 W
Power off: 15 W
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Temperature
Operating: 5°C to 35°C (41°F to 95°F)
Storage: –20°C to 60°C (–4°F to 140°F)
Recording time
Maximum 300 hours (with 160 GB HDD)
(XP): Approx. 34 hours
(SP): Approx. 69 hours
(LP): Approx. 138 hours
(EP): Approx. 209 hours
(FR): Approx. 300 hours
Operating position
Horizontal only
Dimensions (WxHxD)
435 mm x 96 mm x 372 mm (17-1/10" x 3-4/5" x 14-3/5")
Weight
6.2 kg (13.7 lbs)
Input/Output
Video input: 0.5 – 2.0 Vp-p, 75 K (pin jack)
Video output: 1 Vp-p, 75 K (BNC)
Audio input:
–8 dB, 50 kK (pin jack)
Corresponding to mono (left)
Audio output: –8 dB, 1 kK (pin jack)
S-video input:
Y: 0.8 – 1.2 Vp-p, 75 K
C: 0.2 – 0.4 Vp-p, 75 K
S-video output:
Y: 1.0 Vp-p, 75 K
C: 0.3 Vp-p, 75 K
DV: 4-pin for DV IN/OUT
Component video output:
Y: 1.0 Vp-p, 75 K
CB/CR, PB/PR: 0.7 Vp-p, 75 K
Corresponding to copy protection
Remote Input: R3.5 mm Jack
Serial Command: D-SUB 9-PIN
Digital audio output:
Optical, Coaxial
Corresponding to Dolby Digital and DTS Digital Surround
Bit stream
Selectable in digital audio output setting menu
VIDEO/AUDIO (DVD Deck)
Recording time
Maximum 8 hours (with 4.7 GB disc)
(XP): Approx. 1 hour
(SP): Approx. 2 hours
(LP): Approx. 4 hours
(EP): Approx. 6 hours
(FR): Approx. 1 hour – 8 hours
VIDEO/AUDIO (DV Deck)
Signal system
NTSC color signal and EIA monochrome signal, 525 lines/60 fields
Recording system
Digital Component Recording
Format
DV format (SD mode)
Cassette
Mini DV Cassette
Maximum recording time
(SP): 80 min. with M-DV80ME cassette
(LP): 120 min. with M-DV80ME cassette
Audio recording system
PCM 48 kHz, 16 bit (2 ch)/
32 kHz, 12 bit (4 ch)
Specifications shown are for SP mode unless otherwise specified.
TUNER/TIMER
Tuning system
Frequency synthesized tuner
Channel coverage
VHF: Channels 2 - 13
UHF: Channels 14 - 69
CATV: 113 channels
Memory backup time
Approx. 60 minutes
ACCESSORIES
Audio recording system
Dolby Digital (2 ch)
Linear PCM (XP mode only)
Provided accessories
RF cable,
Audio/Video cable,
Infrared remote control unit,
AAAB battery x 2
Video recording compression system
MPEG2 (CBR/VBR)
E.& O.E. Design and specifications subject to change without
notice.
ATTENTION:
This unit contains microcomputers. External electronic noise or
interference could cause malfunctioning. In such cases, switch
the unit off and unplug the AC power cord. Then plug it in again
and turn the unit on. Take out the disc. After checking the disc,
operate the unit as usual.
Page 88
Friday, 6 May 2005 12:06
Filename [DVM70S_15IX.fm]
Masterpage:Right0
DVM70S_00.book Page 89 Friday, May 6, 2005 12:06 PM
LIST OF TERMS
EN
89
A
O
A-B Repeat Playback ................................................ 30
Accidental erasure prevention .................................... 41
Adjusting The Picture Quality ..................................... 31
Angle Selection ........................................................ 27
Audio Channel Selection ........................................... 28
Audio Language/Sound Selection ............................... 28
Auto Channel Set ..................................................... 22
Auto Daylight Saving Time ........................................ 21
On-screen Bar .......................................................... 29
On-screen Language Set ........................................... 20
C
Cancel And Change Programs ................................... 49
Check Programs ....................................................... 49
Country/Area Code List for Parental Lock .................... 82
D
Disc menu ............................................................... 25
Disc Remaining Time ...........................................35, 38
Disc Resume ........................................................... 71
Discs For Playback Only ............................................. 8
DVD menu ............................................................... 25
E
Elapsed Recording Time Indication .......................35, 38
F
File Structure Of Discs ................................................ 9
Free Rate Function ................................................... 36
G
Guide Channel Number ............................................. 73
I
Instant Replay ......................................... 28, 40, 42, 45
Instant Timer Recording (ITR) ...............................35, 38
Interlaced scan ......................................................... 76
P
Pan&Scan ................................................................ 23
Play List ................................................................... 53
Playback Control (PBC) ............................................. 28
Program Playback .................................................... 32
Progressive scan ...................................................... 76
R
Random Playback ..................................................... 32
Recordable/Playable Discs .......................................... 7
Recording Medium And Format .................................... 9
Recording Mode ................................................. 34, 37
Region Number .......................................................... 8
Register Disc ............................................................ 55
Relief Recording ....................................................... 48
Repeat Playback ...................................................... 29
Resume Function ..................................................... 26
Resuming Playback .................................................. 45
RetroActive Recording .............................................. 45
S
Select The Switching Interval Of The Slide Show ......... 32
Semiauto Clock Set .................................................. 21
Setting The Progressive Mode ................................... 32
Simulated Surround Effect ......................................... 31
Simultaneous Recording and Playback ....................... 45
Skip Search ..................................................26, 39, 42
Slow Motion ..................................................26, 39, 42
Soundtrack Selection ................................................ 42
Still Picture/Frame-By-Frame Playback ............25, 39, 42
Subtitle Selection ...................................................... 28
J
T
Jump Search .......................................................26, 40
Temporary Recording ................................................ 45
Time Code ............................................................... 42
Time Search ............................................................ 31
Top menu ................................................................ 25
L
Language Code List .................................................. 81
Last Function Memory ............................................... 76
Letter Box ................................................................ 23
Live Memory ............................................................ 45
M
Manual Channel Set ................................................. 22
Manual Clock Set ..................................................... 21
Marking Positions To Play Back Again Later ...........27, 40
Menu/Audio/Subtitle Language Set ............................. 20
Mode Lock ............................................................... 76
U
Unplayable Discs ........................................................ 8
Usable cassettes ...................................................... 41
V
Variable Speed Search ................................... 25, 39, 42
W
Weekly/Daily Recording ............................................ 47
N
Next Function Memory .............................................. 42
Page 89
Friday, 6 May 2005 12:06
Filename [DVM70S_15IX.fm]
DVM70S_00.book Page 90 Friday, May 6, 2005 12:06 PM
90
EN
Page 90
Masterpage:Left-No-Heading
MEMO
Friday, 6 May 2005 12:06
Filename [DVM70S_15IX.fm]
DVM70S_00.book Page 91 Friday, May 6, 2005 12:06 PM
Masterpage:Right-No-Heading
MEMO
Page 91
EN
91
Friday, 6 May 2005 12:06
DVM70S_00.book Page 92 Friday, May 6, 2005 12:06 PM
EN
SR-DVM70US
© 2005 Victor Company of Japan, Limited
US
Printed in China
0405CSH-SW-BJ
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement