JVC UX-GP5 User's Manual
Warnings, Cautions and Others
Mises en garde, précautions et indications
diverses
IMPORTANT FOR LASER PRODUCTS
1. CLASS 1 LASER PRODUCT
2. CAUTION: Do not open the top cover or cabinet. There
are no user serviceable parts inside the unit; leave all
servicing to qualified service personnel.
3. CAUTION: Visible and/or invisible class 1M laser radiation
when open. Do not view directly with optical instruments.
4. REPRODUCTION OF LABEL: CAUTION LABEL, PLACED
INSIDE THE UNIT.
IMPORTANT POUR PRODUITS LASER
1. PRODUIT LASER CLASSE 1
2. ATTENTION: N’ouvrez pas le couvercle supérieur ni
le coffret de l’appareil. Il n’y a aucune pièce réparable
par l’utilisateur à l’intérieur de l’appareil; confiez toute
réparation à un personnel qualifié.
3. ATTENTION: Rayonnement laser visible et/ou invisible
de classe 1M une fois ouvert. Ne pas regarder directement
dans le faisceau avec des instruments optiques.
4. REPRODUCTION DE L’ÉTIQUETTE: ÉTIQUETTE DE
PRÉCAUTION PLACÉE À L’INTERIEUR DE L’APPAREIL.
MICRO COMPONENT SYSTEM
UX-GP5
—Consists of CA-UXGP5 and SP-UXG300
The lightning flash with arrowhead symbol,
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
“dangerous voltage” within the products
enclosure that may be of sufficient magnitude
to constitute a risk of electric shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Thank you for purchasing a JVC product.
INSTRUCTIONS
Basic and Common Operations
STANDBY lamp
Point at the remote sensor on the front panel.
(The operating range is approx. 7 m.)
CAUTION: Proper Ventilation
To avoid risk of electric shock and fire, and to prevent
damage, locate the apparatus as follows:
1. Front: No obstructions and open spacing.
2. Sides/Top/Back: No obstructions should be placed in the
areas shown by the dimensions below.
3. Bottom: Place on the level surface. Maintain an adequate
air path for ventilation by placing on a stand with a height
of 10 cm or more.
For Canada/pour le Canada:
THIS DIGITAL APPARATUS DOES NOT EXCEED THE CLASS
B LIMITS FOR RADIO NOISE EMISSIONS FROM DIGITAL
APPARATUS AS SET OUT IN THE INTERFERENCE-CAUSING
EQUIPMENT STANDARD ENTITLED “DIGITAL APPARATUS,”
ICES-003 OF THE DEPARTMENT OF COMMUNICATIONS.
CET APPAREIL NUMERIQUE RESPECTE LES LIMITES DE
BRUITS RADIOELECTRIQUES APPLICABLES AUX APPAREILS
NUMIRIQUES DE CLASSE B PRESCRITES DANS LA NORME SUR
LE MATERIEL BROUILLEUR; “APPAREILS NUMERIQUES”, NMB003 EDICTEE PAR LE MINISTRE DES COMMUNICATIONS.
©2008 Victor Company of Japan, Limited
Le symbole de l’éclair à l’intérieur d’un triangle
équilatéral est destiné à alerter l’utilisateur sur
la présence d’une “tension dangereuse” non
isolée dans le boîtier du produit. Cette tension
est suffisante pour provoquer l’électrocution
de personnes.
Le point d’exclamation à l’intérieur d’un
triangle équilatéral est destiné à alerter
l’utilisateur sur la présence d’opérations
d’entretien importantes au sujet desquelles
des renseignements se trouvent dans le
manuel d’instructions.
Caution —
(Standby/on) button!
Disconnect the mains plug to shut the power off completely
(the STANDBY lamp goes off). When installing the apparatus,
ensure that the plug is easily accessible. The
(Standby/on)
button in any position does not disconnect the mains line.
• When the system is on standby, the STANDBY lamp lights
red.
• When the system is turned on, the STANDBY lamp goes off.
The power can be remote controlled.
(attente/sous tension)!
ATTENTION—Touche
Déconnectez la fiche secteur pour mettre l’appareil
complètement hors tension (le témoin STANDBY l s’éteint).
Lors de l’installation de l’appareil, assurez-vous que la fiche
soit facilement accessible. La touche
(attente/sous tension)
dans n’importe quelle position ne déconnecte pas l’appareil
du secteur.
• Quand l’appareil est en mode d’attente, le témoin STANDBY
est allumé en rouge.
• Quand l’appareil est sous tension, le témoin STANDBY
s’éteint.
L’alimentation peut être commandée à distance.
Note to CATV system installer:
This reminder is provided to call the CATV system
installer’s attention to Section 820-40 of the NEC which
provides guidelines for proper grounding and, in particular,
specifies that the cable ground shall be connected to the
grounding system of the building, as close to the point of
cable entry as practical.
[European Union only]
[Union européenne seulement]
Side view
PHONES jack
Select a source
See “Playing Back a Disc” on page 4 and “Listening to an
iPod” on page 5.
Stereo mini plug cord
Connections
Press and hold until the AHB indicator lights up.
• When Sound Turbo function is activated (see above),
this function cannot be activated.
To cancel this function, press and hold again when
Sound Turbo function is deactivated.
Press once for adjusting the bass level; twice for treble
level, then, press VOLUME +/–.
Adjustable range: –3 to +3.
—
Adjust the tone
(Bass/Treble)
—
Using Headphones
Be sure to turn down the volume before connecting or putting on the headphones.
• Connecting the headphones will deactivate the speakers.
• Sound adjustments also affect the sound through the headphones.
Change the display
brightness
NOTE:
DO NOT turn off (standby) the System with the volume set to an extremely high level;
otherwise, the sudden blast of sound can damage your hearing, speakers and/or
headphones when you turn on the System or start playback.
—
Change the display
information (Clock
and Source)
Set the Save Mode
You can dim the display window and illumination lamp.
While the System is turned on...
For setting the clock, see “Setting the Clock and Using
Timers” on page 6.
—
—
Press when the System is on standby.
Setting the save mode allows you to reduce power
consumption by turning the display off while on
standby.
To cancel this function, press again when the System
is on standby.
3
Do not connect the AC power cord until all other connections have been made.
To connect the FM antenna (supplied)
Extend it so that you can obtain the best reception.
To connect the AM loop antenna (supplied)
To assemble the AM loop antenna
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
This System can play back...
– CD.
– CD-R/CD-RW recorded in audio CD format (CD-DA) or recorded MP3/WMA files
in ISO 9660 format.
• When playing back an MP3 or WMA track, MP3 or WMA indicator lights up.
FM antenna (supplied)
AM loop antenna (supplied)
Turn it until the best reception
is obtained.
Loading a Disc (on the System only)
Outdoor FM antenna
(not supplied)
When you use the remote control for the first time, pull out
the insulation sheet.
Disconnect the supplied FM antenna, and connect
to an outdoor FM antenna using a 75 Ω wire with
coaxial type connector (IEC or DIN45325).
1
Press to open the disc tray.
2
• When using an 8 cm disc, place it on the inner
circle of the disc tray.
Basic Disc Operations
To
Play back the disc
Stop playback
Select a track
Press
Programming the Playing Order—Program Play
Indication/Result
• Current track number and elapsed playing
time appear.
For MP3/WMA files: Before current track
number and elapsed playing time appear, the
tag information appears if it is recorded.
• During playback, press again to pause.
• While playback is stopped, total track number
and total playing time (for MP3/WMA files,
group number and track number) appear.
Select the next tracks.
Select a group
(MP3/WMA only)
Rear view
To connect the speaker cords
Lithium coin battery
(product number: CR2025)
Forward search/
Reverse search
Prohibiting Disc Ejection
Press and hold
NOTES:
• Store the battery in a place where children cannot reach. If
a child accidentally swallows the battery, consult a doctor
immediately.
• To prevent the battery from over-heating, cracking, or starting
a fire:
– Do not recharge, short, disassemble or heat the battery or
dispose of it in a fire.
– Do not leave the battery with other metallic materials.
– Wrap the battery with tape and insulate when throwing
away or saving it.
– Do not poke the battery with tweezers or similar tools.
• Dispose of battery in the proper manner, according to federal,
state, and local regulations.
• The batteries (battery pack or batteries installed) shall not be
exposed to excessive heat source such as sunshine, fire or the
like.
(on the System only)
You can lock the disc tray so that no one can eject the loaded disc.
• This is possible while the System is on standby.
To cancel the prohibition, repeat the same procedure.
+
Select the next groups.
Press and hold to fast-forward the track during
playback.
To stop searching, release the button.
Press and hold to fast-reverse the track during
playback.
To stop searching, release the button.
NOTES:
• If no disc is inserted, “NO DISC” appears on the main display.
• If MP3/WMA files are not recorded on the disc, “NO PLAY” appears on the main
display.
Playing Repeatedly—Repeat Play
Release
Insert
1
Press repeatedly to specify the repeat mode as follows:
Red
REP TRK: Repeats the current (or specified) track. [ ]
REP GRP: Repeats all tracks in the current group (MP3/WMA
only). [ ]
REP ALL: Repeats all tracks. [ ALL ]
REP OFF: Normal playback
To a wall outlet
Plug the AC power cord only after all connections are complete.
NOTES:
• Make sure the antenna conductors do not touch any other terminals, connecting cords and power cord. Also, keep the antennas
away from metallic parts of the System, connecting cords, and the AC power cord. This could cause poor reception.
• Make sure both the speakers are connected correctly and firmly.
• When connecting the speaker cords, match the polarity of the speaker terminals: red color to (+) and black color to (–).
• DO NOT connect more than one speaker to each terminal.
• DO NOT allow the conductor of the speaker cords to be in touch with the metallic parts of the System.
2
From right
speaker
Black
From left
speaker
3
4
5
•
•
•
•
•
or
During stops, press until the PRGM (program) indicator lights up
before playing.
• For MP3/WMA files: Select a group number, then a track
number.
• For CD: Select a track number.
Press to program the selected group/track.
Repeat steps 2 and 3 to program other tracks you want.
• If you try to program a 51st track, “FULL” will appear.
The tracks are played back in the programmed order.
To check the programmed contents, press 4 or ¢.
To add tracks, repeat steps 2 and 3 above.
To erase the last programmed track, press CANCEL.
To erase the entire program, press and hold CANCEL for about 2 seconds.
To exit from program play, press MODE.
– The stored program is kept.
Select the previous groups.
Press to close the disc tray.
3
1
2
Operations for Program Play (while not playing)
To go back to the beginning of the current or
previous tracks.
Insulation sheet
CAUTION:
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
—
Playing Back a Disc
Prepare the Remote Control
For USA-California Only
This product contains a CR Coin Cell Lithium Battery which
contains Perchlorate Material – special handling may
apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate
To restore the volume, press again, or adjust the
volume level.
The
indicator lights up.
To cancel this function, press repeatedly until
indicator lights off.
The S.TURBO indicator lights up.
To cancel this function, press again.
—
Reinforce the bass
sound (Active Hyper
Bass Pro function)
How to cancel the demonstration
Press and hold DEMO button while on standby. (Refer to the attached “Information
about the demonstration function.”)
For better FM reception
To Replace the Battery in the Remote Control
Adjustable range: Level 0 (“VOL MIN”) to level 40
(“VOL MAX”).
Emphasize the
sound (Sound Turbo
function)
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
Getting Started
Supplied Accessories
The STANDBY lamp on the System turns off/on.
Drop the volume in a
moment
Activate the EALA
surround mode
1
After unpacking, check to be sure that you have all the
following items.
• Remote control, RM-SUXGP5A (× 1)
• Lithium coin battery CR2025 (× 1)
– The battery has been installed when shipped from the
factory.
• AM loop antenna (× 1)
• FM antenna (× 1)
If anything is missing, consult your dealer immediately.
Turn on or off
(standby) the power
Front view
CAUTION:
• Do not block the ventilation openings or holes. (If the
ventilation openings or holes are blocked by a newspaper
or cloth, etc., the heat may not be able to get out.)
• Do not place any naked flame sources, such as lighted
candles, on the apparatus.
• When discarding batteries, environmental problems
must be considered and local rules or laws governing the
disposal of these batteries must be followed strictly.
• Do not expose this apparatus to rain, moisture, dripping
or splashing and that no objects filled with liquids, such as
vases, shall be placed on the apparatus.
• Excessive sound pressure from earphones or headphones
can cause hearing loss.
Indication/Result
Press repeatedly to select “FM” or “AM.”
• For “FM/AM,” see “Listening to FM and AM
Broadcasts” on page 5.
See “Listening to Digital Audio Player” on page 5.
CAUTION:
Changes or modifications not approved by JVC could void
the user’s authority to operate the equipment.
For customer use:
Enter below the Model No. and Serial No. which are
located either on the rear, bottom or side of the cabinet.
Retain this information for future reference.
Model No.
Serial No.
Press
System Remote
To
Adjust the volume
GVT0242-019B[J/C]
0108WMKMDWJMM
For U.S.A.
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules.
These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or
television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and
receiver. Connect the equipment into an outlet on a circuit
different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician
for help.
CAUTION
To reduce the risk of electrical shocks, fire, etc.:
1. Do not remove screws, covers or cabinet.
2. Do not expose this appliance to rain or moisture.
ATTENTION
Afin d’éviter tout risque d’électrocution, d’incendie, etc.:
1. Ne pas enlever les vis ni les panneaux et ne pas ouvrir le
coffret de l’appareil.
2. Ne pas exposer l’appareil à la pluie ni à l’humidité.
2
Playing at Random—Random Play
1
2
Press until the RND (random) indicator lights up before you start
playback.
Playback starts in random order.
Random Play ends when all tracks are played back.
Operations for Random Play
• To skip a track, press ¢.
• To go back to the beginning of the current track, press 4.
• To exit from random play, press MODE while playback is stopped.
RESUME Play (For MP3/WMA only)
When you stop the playback by one of the following operations, this System
stores the beginning of the stopped track on the disc.
– Pressing 7 once
– Changing the source
When you start playback again, playback starts from the stored position.
To clear the stored position, open the disc tray.
• When you clear the stored position and start playback, playback starts from the
beginning of the first track.
NOTE:
This function does not work in Program Play and Random Play.
4
GVT0242-019A EN_UX-GP5[JC]ff
Listening to an iPod
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
To
Display the menu/
Go back to the
previous menu
Select an item on
the menu
Press
—
• The UP/DOWN buttons work in the same
way as operating the iPod’s click wheel
counterclockwise/clockwise. (Refer to the
iPod’s instruction manual for details.)
or
Connecting an iPod
Front view
Open the direct
dock for iPod.
Insert the iPod directly to
the connector pins in the
direct dock for iPod.
Direct dock for iPod
Apple iPod
(separately
purchased))
Connector pins
• Be sure to reduce the volume on the System to the minimum level before
connecting an iPod. Adjust the volume after starting playback.
• DO NOT connect or disconnect the iPod when the System is turned on.
• You cannot send any data to your iPod from the System.
• Do not carry the System with iPod dock open and iPod is connected. You might
drop it or it might cause damages to the iPod dock.
• Do not touch or hit the iPod terminal pins or connector pins in the iPod dock
directly. It might cause damages to the connector part.
Basic iPod Operations
To
Play back an iPod
Press
Select a track
Change the
charge mode
(on the System
only)
Indication/Result
The System detects the iPod and starts
playback.
• To turn off the iPod, press and hold for
more than 2 seconds.
Select the next tracks.
• Press and hold to fast-forward the track
during playback.
To stop searching, release the button.
To go back to the beginning of the current
or previous tracks.
• Press and hold to fast-reverse the track
during playback.
To stop searching, release the button.
Press and hold while “iPod” is selected as the
source. To select the charge mode:
Play back at
random
Play back
repeatedly
Turn on iPod’s
backlight
Presetting Stations
Indication/Result
• Refer to the iPod’s instruction manual for
details.
• Refer to the iPod’s instruction manual for
details.
Press and hold for 2 seconds.
You can preset 30 FM and 15 AM stations manually.
Tune in to a station you want to preset.
• You can also store the FM reception mode.
Press to activate the preset number entry mode.
• Finish the following steps while the indication on the
display is flashing.
Press to select a preset number for the station you want to
or
store.
1
2
3
4
Press to store the station.
Listening to Digital Audio Player
Listening to FM and AM Broadcasts
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
Listening to Digital Audio Player
Front view
Digital Audio Player
Basic Tuner Operations
To
Select FM or AM
Press
Select a frequency
or
Tune in to a preset
station
or
Indication/Result
Press repeatedly.
• The selected frequency band appear.
Press and hold for more than 2 seconds.
The System starts searching for stations and
stops when a station of sufficient signal
strength is tuned in.
• If an FM program is broadcast in stereo,
the S (stereo) indicator lights up (only
when the reception is good).
• Press during searching to stop.
• Press repeatedly to change the frequency
step by step.
Press to select its preset number.
• For presetting stations, see below.
Press to improve reception.
The M (mono) indicator lights up.
Stereo effect will be lost.
To restore the stereo effect, press again.
Change the FM
reception mode
(When an FM
stereo broadcast is
hard to receive)
Stereo mini plug cord
(not supplied)
To audio output (or
headphone out, etc.)
1
Turn the volume to minimum.
2
3
4
Press repeatedly to select “AUDIO IN.”
Learning More about This System
Basic and Common Operations (see page 3)
• Pressing one of the source buttons also turns on the System
and starts playing back if the source is ready or connected.
Playing Back a Disc (see page 4)
• This System cannot play “packet write” discs.
• For MP3/WMA playback...
– In this manual, “file” and “track” are interchangeably used
for MP3/WMA operations.
– This System can show the Tag data (Version 1).
– MP3/WMA discs are required a longer readout time than
regular CDs. (It depends on the complexity of the group/
file configuration.)
– Some MP3/WMA files cannot be played back and will be
skipped. This result from their recording processes and
conditions.
– When making MP3/WMA discs, use ISO 9660 Level 1 or
Level 2 for the disc format.
– This System can play back MP3/WMA files with the
extension code <.mp3> or <.wma> (regardless of the
letter case—upper/lower).
– It is recommended that you make each MP3/WMA file at a
sampling rate of 44.1 kHz and at bit rate of 128 kbps. This
System cannot play back files made at bit rate of less than
64 kbps.
– Playback order of MP3/WMA tracks may be different from
the one you have intended while recording. If a folder
does not include MP3/WMA tracks, they are ignored.
• This System can recognize up to 99 groups in a disc. The
total number of groups and tracks (in a disc) that can be
recognized by the System is 512 (for MP3/WMA).
Playing Back an iPod (see page 5)
• Compatible iPod:
– iPod nano 1GB/2GB/4GB
– iPod nano (2nd Generation) 2GB/4GB/8GB
– iPod nano (3rd Generation) 4GB/8GB
– iPod mini 4GB/6GB
– iPod (4th Generation) 20GB/40GB
– iPod photo (4th Generation) 20GB/30GB/40GB/60GB
– iPod video (5th Generation) 30GB/60GB/80GB
– iPod touch (1st Generation) 8GB/16GB
• If incompatible iPod type is connected, the iPod may not be
operated from the System. To enable the operation, before
connecting the iPod, switch the charge mode to “OFF” (see
page 5) with “iPod” selected as source.
• Sound distortion may occur when playing back audio
sources with high recording levels. When distortion occurs,
it is recommended to turn off the equalizer of the iPod. For
information on operating the iPod, see the iPod instruction
manual.
S.TURBO (Sound Turbo) indicator (See page 3.)
Start playing the Digital Audio Player connected.
Setting the Clock and Using Timers
Adjust the volume.
2
or
Setting the Daily Timer
Using Daily Timer, you can wake up with your favorite music.
• You can store three Daily Timer settings; however, you can activate only one of
the Daily Timers.
Press repeatedly to select one of the timer setting modes
you want to set—DAILY 1 ON time, DAILY 2 ON time, or
DAILY 3 ON time—as follows:
1
• To exit from the clock setting, press CLOCK/TIMER as required.
• To go back to the previous step, press CANCEL.
Setting the Sleep Timer
When the System is on, press repeatedly to specify the time (in
minutes) as follows:
The SLEEP indicator lights up.
• To check the remaining time until the System shuts off, press once.
3
No sound is heard.
\ Speaker connections are incorrect or loose.
\ Headphones are connected.
The System does not work properly.
\ Many functions of this System are implemented by
microcomputers. If the System does not work correctly,
disconnect the AC power cord from the wall outlet, wait
for a while, and connect the cord again.
Play mode indicators (See page 4.)
1 Adjust the hour then the minute for on-time.
2 Adjust the hour then the minute for off-time.
3 Select the playback source—“TUNER-FM,” “TUNER-AM,”
“DISC,” “AUDIO IN,” or “IPOD.”
4 For “FM/AM”: Select a preset channel.
For “DISC”: Select a track. (For MP3/WMA: Select the
group, then the track number.).
For “AUDIO IN”: Make the connected device ready for
playback.
5 Select the volume.
• You can select the volume level (“VOLUME 0”
(VOL MIN) to “VOLUME 40” (VOL MAX) and
“VOLUME – –”). If you select “VOLUME – –,” the volume
is set to the last level when the System is turned off.
Turn off the System (on standby).
• When the on-time comes, the System sets the volume
gradually to the preset level.
• To exit from the timer setting, press CLOCK/TIMER as required.
• To correct a misentry during the process, press CANCEL. You can return to the
previous step.
1 Press repeatedly to select “DAILY 1,” “DAILY 2,” or “DAILY 3.”
2
To turn on the Daily Timer again, select one of the timer settings by pressing
CLOCK/TIMER, then press SET.
Turning Off the System Automatically
—AUTO STANDBY function (only for Disc/iPod)
Press and hold until the A.STBY indicator lights on the display.
• The A.STBY indicator starts flashing after playback stops.
If no operation is done for about 3 minutes, the System turns off.
• Not applicable for FM/AM/AUDIO IN.
To cancel this function, press and hold again.
6
The iPod does not play, but “CONNECT” appears on the
display.
\ The iPod battery is low or exhausted. Charge the iPod
battery.
Radio Operations
Hard to listen to broadcasts because of noise.
\ Antennas connections are incorrect or loose.
\ The AM loop antenna is too close to the System.
\ The FM antenna is not properly extended and
positioned.
\ Electrostatic discharge from your body may cause noise.
If this happens, turn off and on the System again.
Timer Operations
Daily Timer does not work.
\ The System has been turned on when the on-time
comes. Timer starts working only when the System is
turned off.
Microsoft and Windows Media are either registered
trademarks or trademarks of Microsoft Corporation in the
United States and/or other countries.
iPod is a trademark of Apple Inc., registered in the U.S. and
other countries.
Disc Operations
The disc does not play.
\ The disc is placed upside down. Place the disc with the
label side up.
\ The disc is recorded with the “packet writing (UDF file
system).” It cannot be played. Check the files you want to
play back.
MP3/WMA groups and tracks are not played back as you
expect.
\ Playing order is determined when the groups and tracks
were recorded. It depends on the writing application.
FM reception indicators (See page 5.)
The disc sound is discontinuous.
\ The disc is scratched or dirty.
If the sound from the Digital Audio Player connected to the AUDIO IN jack is too
loud or too quiet, you can change the audio input level through the AUDIO IN jack
(without changing the volume level).
The disc tray does not open or close.
\ The AC power cord is not plugged in.
\ Disc ejection is prohibited (see page 4).
Timer mode indicators
(See page 6.)
SLEEP indicator (See page 6.)
Main display
A.STBY (Auto Standby) indicator (See page 6.)
7
Notes on the power cord
• When you are away on travel or otherwise for an extended period of time,
remove the plug from the wall outlet.
• When unplugging the System from the wall outlet, always pull the plug, not the
power cord.
• Do not handle the power cord with wet hands.
• Disconnect the power cord before cleaning the System or moving the System.
• Do not alter, twist or pull the power cord, or put anything heavy on it, which may
cause fire, electric shock, or other accidents.
• If the cord is damaged, consult a dealer and have the power cord replaced with a
new one.
Avoid moisture, water, dust, and high temperatures
• Do not place the System in moist or dusty places.
• If water gets inside the System, turn off the power and remove the plug from the
wall outlet, then consult your dealer. Using the System in this state may cause a
fire or electrical shock.
• Do not expose the System to direct sunlight or place it near a heating device.
Notes on installation
• Select a place which is level, dry and neither too hot nor too cold—between 5˚C
(41˚F) and 35˚C (95˚F).
• Do not install the System in a place subject to vibrations.
• Do not put heavy objects on the System.
To prevent malfunction or damage of the System
• Do not insert any metallic objects, such as wires, hairpins, coins, etc. into the
System.
• Do not block the vents.
There are no user-serviceable parts inside. If anything goes wrong, unplug
the power cord and consult your dealer.
Maintenance
To get the best performance of the System, keep your discs and mechanism clean.
To Turn Off the Daily Timer
iPod Operations
To Adjust the Audio Input Level
Precautions
1
• If you have already adjusted the clock before, press
the button repeatedly until the clock setting mode is
selected.
Adjust the hour, then the minute.
Unable to operate the System from the remote control.
\ The path between the remote control and the remote
sensor on the System is blocked.
\ The batteries are exhausted.
Source indicators (See page 3.)
5
or
Operations are disabled.
\ The built-in microprocessor may malfunction due to
external electrical interference. Unplug the AC power
cord and then plug it back in.
AHB indicator (See page 3.)
Surround mode indicator (See page 3.)
As the number increases, the sound becomes louder.
2
Adjustments or settings are suddenly canceled before you
finish.
\ There is a time limit. Repeat the procedure again.
Display Information
Source indicators (See page 3.)
Setting the Clock
Power does not come on.
\ Power plug is not inserted securely. Plug in securely.
Setting the Clock and Using Timers (see page 6)
• You can set the clock and Daily Timer while the Save Mode
is turned on. While setting the clock or Daily Timer, the
display is turning on.
• The clock may gain or lose 1 to 2 minutes per month. If this
happens, readjust the clock.
• When you unplug the AC power cord or if a power failure
occurs, the clock and the timer will be canceled. You need
to set the clock first, then the timer again.
Timer Priority:
• If you set the Sleep Timer after Daily Timer starts playing the
selected source, Daily Timer is canceled.
File type indicators (See page 4.)
Without setting the built-in clock, you cannot use Daily Timer and Sleep Timer.
• “0:00” flashes on the main display until you set the clock.
Press to activate the clock setting mode.
General
Press and hold for more than 2 seconds while “AUDIO IN” is selected
as the source.
You can select one of three levels as follows:
P. ON: The battery in the iPod is charged
through the iPod terminal when
“iPod” is selected as the source or
during Standby Mode.
P. OFF: The battery is not charged.
The following operations are explained using the remote control, unless
mentioned otherwise. However, if the System has the same or similar button
names, they can also be used for the operations.
Troubleshooting
If you are having a problem with your System, check this list
for a possible solution before calling for service.
Handling discs
• Remove the disc from its case by holding it at the edge while pressing the center
hole lightly.
• Do not touch the shiny surface of the disc, or bend the disc.
• Put the disc back in its case after use.
• Be careful not to scratch the surface of the disc when placing it back in its case.
• Avoid exposure to direct sunlight, temperature extremes, and moisture.
Specifications
Amplifier section
OUTPUT POWER:
35 W per channel, min. RMS, driven into 4 Ω at 1 kHz with no
more than 10% total harmonic distortion
Speakers/Impedance:
4 Ω – 16 Ω
Audio input AUDIO IN: 500 mV/50 kΩ (at “IN LVL1”)
250 mV/50 kΩ (at “IN LVL2”)
125 mV/50 kΩ (at “IN LVL3”)
Digital input:
iPod
Tuner section
FM tuning range:
87.5 MHz - 108.0 MHz
AM (MW) tuning range: 530 kHz - 1 710 kHz
CD player section
Dynamic range:
Signal-to-noise ratio:
Wow and flutter:
88 dB
85 dB
Immeasurable
iPod section
iPod output power:
DC 5 V
500 mA
Speakers
Speaker units:
Impedance:
Dimensions (W x H x D)
(approx.):
Mass (approx.):
10 cm (3-15/16 inches) cone x 1
4Ω
160 mm x 250 mm x 150 mm
(6-5/16 inches x 9-7/8 inches x
5-15/16 inches)
1.6 kg (3.6 lbs) each
BT-51018-5
(0306)
General
Power requirements:
Power consumption:
AC 120 V , 60 Hz
20 W (power on)
3.5 W (standby mode)
1 W or less (Save Mode)
Dimensions (W x H x D): 165 mm x 251 mm x 255 mm
(6-1/2 inches x 9-15/16 inches x
10-1/16 inches)
Mass:
2.6 kg (5.8 lbs)
Specifications and appearance are subject to change without
prior notice.
To clean the disc:
• Wipe the disc with a soft cloth in a straight line from center to edge.
Cleaning the System
• Stains should be wiped off with a soft cloth. If the System is heavily stained, wipe
it with a cloth soaked in water-diluted neutral detergent and wrung well, then
wipe clean with a dry cloth.
• Since the System may deteriorate in quality, become damaged or get its paint
peeled off, be careful about the following:
– DO NOT wipe it hard.
– DO NOT wipe it with thinner or benzine.
– DO NOT apply any volatile substance such as insecticides to it.
– DO NOT allow any rubber or plastic to remain in contact for a long time.
8
GVT0242-019A EN_UX-GP5[JC]f
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising