Kenmore 625.3835 User manual

Kenmore 625.3835 User manual
Use & Care
Manual
English
Guide
Sy;tem
nternational
de Uso y Cuidado
/
tested
and certif ed by NSIF
against II",,,,ISIF/ANSStandard
for ha dness reduction.
44
Espa_ol
IEste s sterna ha sdo probado y cert f cado
por NSF Internat onal de acuerdo a
I!"rrl,
orma INSIF!AIIXrJ,
SI 44
para la reducci6n de la dureza,,
Model
,/Modelo
No. 625.383500
I(enmore
wth
High Flow Valve
Agua
co_"_valvula
de al_o flu]o
Sears Brands Management
Hoffman Estates, IL 60179
www.kenmorewater.com
Corporation
U.S.A.
www.kenmore.com
www.sears.com
®
Printed on recycled paper/
Impreso en papel reciclado
P/N 7325207
(Rev. A 12/22/I0)
WARRANTY
ONE YEAR LIMITED WARRANTY
When
installed,
operated
ON KENMORE WATER SOFTENER
ON WATER SOFTENER
and maintained
according
to all instructions
supplied
Kenmore appliance fails due to a defect in material and workmanship
chase, call 1-800-4-MY-HOME
® to arrange for free repair.
TEN YEAR LIMITED WARRANTY
When
installed,
operated
AGAINST
and maintained
within
with the product,
if this
one year from the date of pur-
LEAKS
according
to all instructions
supplied
with the product,
if the water
softener tank or salt storage drum develops a leak within ten years from the date of purchase,
call 1-800-4-MY-HOME
® to arrange for free tank or drum replacement.
After the first year you must pay an
initial
trip charge.
All warranty
coverage
If this appliance
does not include
water
is used for other than private
softener
family
resin, which
is an expendable
purposes, this warranty
item.
applies
for only 90 days from
the date of purchase.
This warranty
covers only defects in material
1. A service technician
to instruct
2. A service technician
to clean or maintain
and workmanship.
the user in correct
product
Sears will NOT pay for:
installation,
operated
of this product
resulting
5. Damage
of this product
caused by the use of detergents,
in all instructions
6. Damage
to or failure
Disclaimer
of implied warranties;
from accident,
or maintained
4. Damage to or failure
ed purpose.
to or failure
or maintenance.
this product.
3. Damage to or failure of this product if it is not installed,
instructions supplied with the product.
than those recommended
operation
supplied
of parts or systems resulting
limitation
according
to the all
abuse, misuse or use for other than its intend-
cleaners, chemicals or utensils other
with the product.
from
unauthorized
modifications
made to this product.
of remedies
Customer's sole and exclusive remedy under this limited warranty
shall be product repair as provided herein.
Implied warranties, including warranties
of merchantability
or fitness for a particular
purpose, are limited to
one year or the shortest period allowed by law. Sears shall not be liable for incidental
or consequential damages. Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages, or limitation
on the duration
limitations may not apply to you.
This warranty
applies
This warranty
state.
gives you specific
of implied
only while this appliance
legal
Call the Kenmore
of merchantability
or fitness, so these exclusions
Water
or
is used in the United States or Canada.
rights, and you may also have other rights which vary from
Sears Brands Management
Questions?
warranties
Corporation,
Hoffman
Line 1-800-426-9345
Estates, IL 60179
state to
U.S.A.
or visit www.kenmorewater.com
Warranty
Safety
.....................................................................................
Guides
Specifications
Packing
List
3
& Dimensions
4
Adding
Controller
..........................................................................
the Softener
the Water
Salt to the Storage
Features
Tank
..................................................................
..........................................................................
•
14
14
...........................................................................
Softener
Information
12-13
....................................................................
Service
•
5-7
7-11
.....................................................................
Softener
Care of Your Water
Exploded
5
..................................................................................
Programming
Sanitizing
......................................................................
...................................................................................
Plan Your Installation
Installation
2
..................................................................................
View & Parts List
15-18
.....................................................................
19
19-22
...................................................................
Read all steps and guides carefully before installing
and using your new water softener.
Follow all steps
exactly to correctly install.
Failure to follow them
could cause personal injury or property damage.
Reading this manual will also help you to get all the
benefits from your water softener.
Your Kenmore water softener will remove hardness
minerals from water. This is measured in grains per
gallon (gpg). It will also remove some clear water
iron _:. This is measured in parts per million (ppm).
See the specifications
page for the maximum limits
of hardness and iron removal.
•
A water softener will not improve other water problems such as acidity, tastes and odors, or iron other
than clear water iron.
•
Do not attempt to use this product to make safe
drinking water from non-potable
water sources. Do
not use the system on microbiologically
unsafe water,
or water of unknown quality without adequate disinfection before or after the system.
•
Check with your local public works department
for
plumbing and sanitation codes. You must follow
their guides as you install the system. Follow your
local codes if they differ with guides in this manual.
In Massachusetts,
plumbing code 248-CMR 3.00 and
10.00 shall be adhered to. Consult with a licensed
plumber.
24-27
•
Use only lead-free solder and flux for all sweat-solder
connections, as required by federal codes, when
installing soldered copper plumbing.
•
Use care when handling the water
turn upside down or drop.
•
Avoid installing
cause distortion
parts.
•
This water softener works on water pressures of 20 psi
(minimum) to 125 psi (maximum).
If your house water
pressure is over the maximum, install a pressure reducing valve in the water supply pipe to the softener.
•
This softener works on 24 volt, 60 Hz electrical power
only, supplied by a direct plug-in transformer
(included). Be sure to use the included transformer
and plug
it into a nominal 120V, 60 cycle household outlet that
is properly protected
by an overcurrent device such as
a circuit breaker or fuse. If transformer
is replaced,
use only the authorized
service, Class II, 24V 10VA
transformer.
•
Do not install the water softener outside, or in extreme
hot or cold temperatures.
Temperature
of the water
supply to the water softener must be between 40°F
and 120°F. Do not install on hot water.
in direct sunlight.
or other damage
softener.
Do not
Excessive heat may
to non-metallic
_: The capacity to reduce clear water iron is substantiated
by Water Quality Association test data.
European Directive 2002/96/EC
requires all electrical and electronic
equipment to be disposed of according to Waste Electrical and Electronic
Equipment (WEEE) requirements.
This directive or similar laws are in
place nationally
and can vary from region to region. Please refer to your
state and local laws for proper disposal of this equipment.
Questions?
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
3
Model No. 625.383500
Model
Code
350
Rated Softening
Rated Efficiency
Rated Service
Amount
Capacity
(Grains
(Grains/Pound
Ion Exchange
Water
Supply
Max.
Water
Supply
Max. Clear Water
Water
Pressure Limits (minimum
Water
Temperature
Maximum
Salt Dose)
5,090
Water
Resin
0.83 cu. ft.
Flow
10 psig
Hardness
90 gpg
Iron
11 ppm*
/ maximum)
Limits (minimum
Supply
@ 2.5 Ibs.
8.0 gpm
Pressure Drop at Rated Service
Intermittent
of Salt @ Minimum
Flow Rate
of High Capacity
Minimum
12,600 @ 2.5 Ibs.
26,900 @ Z9 Ibs.
32,100 @ 13.3 Ibs.
@ Salt Dose)
20 - 125 psi
/ maximum)
40 - 120 °F
Flow Rate
3 gpm
Flow @ 15 psi
10 gpm**
Drain Flow Rate
2.0 gpm
*Capacity
to reduce clear water iron is substantiated
by WQA test data.
State of Wisconsin
requires additional
treatment
if water supply contains clear water iron exceeding 5 ppm.
**Intermittent
flow rate does not represent the maximum service flow rate used for detemining the softener's rated capacity and efficiency.
Continuous operation at flow rates
greater than the service flow rate may affect capacity and efficiency
performance.
These systems conform to NSF/ANSI
substantiated
by test data.
44 for the specific
The efficiency
rating is only valid at the stated
rated according
to NSF/ANSI
Standard 44.
Variable
salt dose.
performance
claims as verified
These softeners
Salt Dose: The salt dose is selected by the electronic
based on the amount needed.
controls
and
were efficiency
at regeneration
time
16-1/2" _
3-3/8"
IN - OUT
47-3/4"
41-1/2"
40-1/4"
I
FRONT VIEW
Questions?
4
Call
the
Kenmore
Water
SIDE VIEW
Line 1-800-426-9345
or visit
Figure
www.kenmorewater.com
1
The parts required
to assemble
and install the water
Remove and discard
softener are included with the unit. Thoroughly check
the water softener for possible shipping damage and
parts loss. Also inspect
shipping carton.
and note any damage
to the
iiiiilHliiiii!!
Ground
(or recycle)
all packing
materials.
To avoid loss of small parts, we suggest you keep the
small parts in the parts bag until you are ready to use
them.
l!!!ii
....
Installation
Clamp
Kit
20 ft. Drain Hose
Bypass Valve
Adaptors
Clips
(including
Hose Clamps
THE PROPER ORDER
(Shows sequence
Adaptor
TO INSTALL
of equipment
WATER TREATMENT
only - not all items are needed
Untreated
Outside
Cold Water
to House
Grommet
Elbow
to House
Cartridge
Filter
Water
Softener
Central
Water
EQUIPMENT
in all applications)
City Water Supply
Sediment
Heater
Figure 2
Water to
Faucets
Hot Water
Water
1 spare)
t
Pressure
Tank
I
Iron
Filter
Well Water
Supply
Filtration
Well
Pump
System
• Always
locate
an Iron Filter UPSTREAM of the water
• Locate a Central
water
Water
Filtration
supply, or DOWNSTREAM
Questions?
Call
the
Kenmore
System UPSTREAM of the water
of the water
Water
f
softener.
softener
softener
on a non-chlorinated
Line 1-800-426-9345
on a chlorinated
water
or visit
supply.
Figure
3
www.kenmorewater.com
5
TYPICAL
WHERE
TO INSTALL
Review the following
to put your softener:
THE WATER SOFTENER
points before
you choose a place
1. Place as close as possible to, but always
from, the pressure tank (well water)
(city water).
2. Place as close as possible
floor drain,
laundry
to a water
downstream
or water
meter
drain
such as a
tub, sump or standpipe
(See Fig.
4).
3. Connect
to the house main water
pipe UPSTREAM
OF THE WATER HEATER (See Fig. 3). The temperature of water going through the softener must not be
more than 120°F (49°C).
Hot water will damage
inner softener parts. To reduce the risk of hot water
backup,
heater
piping
between
the softener
4. Keep outside faucets on hard water
water and salt. See Fig. 4.
6
and water
Call the Kenmore
to save soft
Water
5. Do not install in a place where the softener could
freeze. Damage caused by freezing voids the warranty
by Sears Brands Management
6. Put the softener in a place where
least likely to occur if it develops
the manufacturer
damage.
will not repair
Corporation.
water damage is
a leak. Sears or
or pay for water
7. A grounded, 120V, 60 Hz. electrical outlet is needed
within 10 feet of the softener to plug in the transformer (See Fig. 4). Be sure the outlet and transformer are in an inside location, protected from wet
weather.
Use a continuously
"live" outlet, which cannot be accidentally
8. When
should be as long as possible.
Questions?
INSTALLATION
installing
switched
in an outside
off.
location,
you must take
the steps necessary to assure the softener, installation
plumbing, and wiring, are protected from the elements, direct sunlight, contamination,
vandalism, etc.
Line 1-800-426-9345
or visit www.kenmorewater.com
CHECK
YOUR WATER
PRESSURE BEFORE INSTALLING
For your water softener to work properly, incoming
water pressure in your house pipes must be no lower
psi, buy and install a pressure reducing valve
pipe supplying water to the softener's inlet.
than 20 pounds per square inch (psi). The highest
allowable
pressure is 125 psi. If pressure is above 125
NOTE: If water
INSTALL
Complete
and/or
SINGLE
BYPASS VALVE AND/OR
the following
the included
steps to assemble
THREADED
the adaptors
single bypass valve.
INSTALLATION
SINGLE
supply to the water
the day is 100 psi or
the night may go above
ADAPTORS
BYPASS VALVE:
6. Push the bypass valve
1. Close the shutoff valve on the house main water pipe,
near the water meter or pressure tank, to turn off the
water.
2. Shut off the gas or electric
heater.
pressure during
more, pressure during
125 psi.
in the
into the softener
valve's inlet
and outlet ports as far as it will go. Snap the two
large holding clips into place, from the top down as
shown (see Fig. 8).
CAUTION:
Be sure the clips snap firmly
into place so
the bypass valve will not pull out.
3. Open the highest and lowest water faucets in your
house. This will let water drain from the pipes.
Close faucets after water has drained.
4. Remove the top cover. Pull outward on the two tabs
to release top cover (see Fig. 5). The salt lid remains
attached to the top cover when removed.
covers aside so they will not get scratched
Set both
or broken.
INLET AND OUTLET THREADED
7. Push the adaptors
ADAPTORS:
into the valve inlet and outlet
ports, or bypass valve ports, as far as they will go.
Both adaptors are the same and fit either port. Snap
the two large holding
clips into place, as shown (see
Fig. 8).
CAUTION:
Salt Lid
Be sure the clips snap firmly into place so
the adaptors will not pull out.
Top
Clips
Threaded
Installation
Valve
Adaptors
Outlet
Figure
5
5. Visually check and remove any foreign materials from the valve inlet and outlet ports (see
Fig. 6). Carefully remove
clips (you will use them).
the turbine and support
(see Fig. 7).
NOTE:
the two large plastic
Check to be sure
are firmly
in place
Clip
If you will not install the included bypass
valve because you will have a 3-valve
bypass
perform
in your plumbing,
Valve
Inlet
Single
Bypass Valve
skip step 6, but
Clip
step 7.
Figure 6
Questions?
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
7
INSTALLSINGLEBYPASSVALVE(cont.)
ASSEMBLE
Before installing the bypass valve and/or
installation
adaptors, make sure that the turbine and support are
Measure, cut (thread if needed) and put together all
pipe and fittings up to the main water pipe. Make sure
firmly
that the incoming
inlet side.
in place inside the softener
valve's outlet port.
Turbine
CAUTION:
Support
Outlet j"
/
Turbine
HOLDING
Bypass Valve or
Installation
Adaptor
CLIPS
/
\
supply
Never solder
pipe goes to the valve
fittings
parts.
before
while connected
Be careful when putting
er. Do not cross thread,
tighten.
pipe fittings togethand do not over-
Solder.
NOTE: To be certain
that heat will not
1. Cut pipe to
correct
travel down the pipe
and into the bypass
valve or installation
"_
ALTERNATE
BYPASS VALVE
length
2. Solder. When
cool, do step 3.
3. Put threaded
adaptor
into
bypass valve
port.
O-Ring
Plastic clip snaps
into groove in
bypass or adaptor
to
Wait until soldered pipe
connection.
See Fig. 10.
adaptors, wrap the
bottom of the p_pe
and the bypass valve
with a wet rag.
Valve Inlet or Outlet
PLUMBING
Incoming
Hard
Water
o
Plastic Clip
OUTLET
/Vlain _Vater Pipe
Figure 7
INSTALL
water
nonmetallic
has cooled
CAUTION:
Valve
INLET AND
IN
Figure 8
INSTALLATION
Figure 10
If connecting to floor
level plumbing, install
the bypass valve turned
downward,
as shown.
IN
Questions?
Figure 9
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
CONNECT
THE VALVE DRAIN
Take a length of 3/8"
(supplied) and attach
HOSE
COPPER DRAIN
inside diameter drain tubing
one end to the drain fitting (see
To adapt
Fig. 11). Use a tube clamp from the parts bag to hold it
in place. Put the other end of the tubing over a floor
drain, into a laundry tub, standpipe,
drain. Check your local codes.
Leave an air gap of about 1-1/2"
codes may
a copper
drain
tube to the softener, purchase
a compression fitting (1/4" female pipe threads x 1/2"
O.D. tube) and tubing from your local hardware store.
or other suitable
between
TUBE: Local plumbing
require the use a copper valve drain tube. A copper
tube is also best to use if running a drain line overhead.
CONNECT
the end of
SALT TANK
OVERFLOW
HOSE
the hose and the drain. This gap is needed so you
don't get a backflow of sewer water into the softener.
1. Locate the rubber grommet, adaptor elbow and tube
clamp (see Fig. 11) that are in the parts bag.
Do not put the end of the hose into the drain
nect without the air gap.
2. Push the grommet into the hole in the salt tank wall
so that half is inside and half is outside.
Locate and support
or con-
the hose so it does not kink or have
3. Push the larger
sharp bends. Secure the hose end so water pressure
does not cause the hose to "whip".
Tie or wire it in
from the parts
bag to hold it in place.
5. Put the other end of the tubing
or restricted in any way. Direct drain flow down into
drain from drain line as flow could possibly overshoot
the drain cover.
fitting.
into the grommet.
4. Push one end of a length of 3/8" I.D. tubing (supplied) onto the tube adaptor, using a tube clamp
place.
Do not pinch the hose shut. The softener will
not work if this drain hose is pinched, plugged, closed
Keep the hose lower than the drain
end of the adaptor
IMPORTANT:
Overflow
water
over the floor
must run down
drain.
by gravity
through the tubing.
Do not raise the tubing higher than the adaptor (see Fig. 11).
In some
IMPORTANT:
homes, to get to a drain you must raise the hose and
run it overhead.
Do not raise the hose more than 8 feet
above the floor.
Do not connect
this hose to the valve
drain hose you just installed (see above).
Both drains must have a separate hose.
1/4 NPT
Threads
SUBSTITUTING
RIGID
DRAIN
LINE
Barbs
1/2" Outside
Diameter Copper
Tube (not supplied)
Clip
Fitting
Cut barbs from
drain fitting (pull
clip and remove
fitting from valve)
Compression Fittin,
1/4 NPT x 1/2" O.D.
Tube (not supplied)
x_,
\\
\\
\\
\\
Grommet
Tube
--,._,=\/_lv_
Drain Hose
\\
\\
Todrain
point other
._.
than floor
_
drain.
.....
STANDPIPE
Support
tubing in place
Tie or wire
tubing in
1-1/2"
Air Gap
as needed.
Gap
place
NOTE: Drain Hose
(20 ft.) is included.
See also parts list.
Salt Tank
Overflow
Hose
Questions?
Call the Kenmore
FLOOR DRAIN
Figure 11
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
9
LEAKTEST
SINGLE
To check for leaks, complete
CAUTION:
the following
BYPASS VALVE
steps:
To avoid water or air pressure damage to
softener inner parts, and to flush pipe chips
Pull stem outward
for Service
or other residue from the water pipes, be
sure to do the following steps exactly as
instructed.
1. Fully open two nearby cold water
stream from the softener.
faucets
Push inward
for Bypass
down-
2. Place bypass valve(s) in "bypass" position (see
Figures 12 & 13). On a single valve, slide the stem
inward to bypass. On a 3-valve bypass, close the
inlet and outlet valves and open the bypass valve.
3. Fully open the house main water
Observe
steady
water
flow from
pipe shutoff
valve.
Figure 12
both open faucets.
4. Place bypass valve(s) in SERVICE, EXACTLY as follows: Keep soft water faucets open.
a. Single Bypass Valve: Slowly, slide pull the valve
stem outward toward service, pausing several times
to allow the softener to pressurize gradually.
b. 3-Valve Bypass: Fully close the bypass valve and
open the outlet valve.
Slowly open the inlet valve,
pausing several times to allow the softener to pressurize gradually.
5. After about three minutes, open a hot water faucet
for about one minute, or until all air is expelled, then
close.
6. Close both cold water
3-VALVE
If this procedure
Bypass
Valve
FOR SERVICE
Close bypass valve.
Open inlet & outlet
valves.
Outlet
Valve
Inlet
Valve
FOR BYPASS
Open bypass valve.
Close inlet & outlet
valves.
faucets.
7. Check your plumbing work for leaks, and fix right
away if any are found. Be sure to observe previous
caution notes.
NOTE:
BYPASS
is performed
Figure 13
on a new softener,
water coming from the taps may initially be discolored.
This normally occurs the first time
water runs through the resin bed. The discolored water is not harmful, and the discoloration
will not last more than a few minutes.
Questions?
10
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
INSTALL
GROUNDING
CLAMP
METAL
PIPE GROUNDING
The house cold water pipe (iron or copper) is often used
to ground all electrical outlets in the home. To maintain
this ground, use the ground clamp kit included in the
parts bag. Install the ground clamp across the inlet
and outlet metal pipes (see Fig. 14). Make sure good
contact is made between the pipe and the clamps.
INSTALL
After
TO
Valve Inlet
8
Ground
(2 Clamp
halves) "'_1
COVERS
installing your water
softener,
put the covers on.
Angle the covers so the top cover clips onto the back
Screw with J
Iockwasher
& nut
first, then bring down in front and clip on the tabs
inside the rim and lower the salt lid closed (See Fig. 5).
CONNECT
TO ELECTRICAL
FROM
Valve Inlet
POWER
The softener
works on 24 volt, 60 Hz electrical
The included
house power
transformer
to 24 volts.
ener's transformer
Be sure the outlet
switched
power.
Figure 14
changes standard 120 volt AC
You must plug the water soft-
into a grounded, 120 volt outlet
is always "live" so it cannot be
only.
off by mistake.
NOTE: The electrical outlet you plug the transformer
into must be indoors, protected from weather.
RESTART THE WATER HEATER
Turn on the gas (or electric)
and light the pilot.
YOUR
PLUMBING
ELECTRICAL
Questions?
WORK
supply to the water
heater
INSTALLATION
AND
ARE NOW
COMPLETE.
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
11
SET SALT LEVEL button
UP button
Display
SELECT button
/
TANK LblGtH_
ht_
A_T
/
REGENERATION
PROGRAM
When
\
LOW SALT indicator
button
THE SOFTENER
the transformer
is plugged
SET WATER
into the electrical
out-
let, the model code (350) and a test number (example:
J3.0), are briefly shown in the display. Then the words
"PRESENT TIME"
appear
DOWN
button
Figure 15
HARDNESS
NUMBER
If you completed
the previous step, the word "HARDNESS" should show in the display. Otherwise, press the
SELECT button
several times until they do.
and 12:00 PM begins to flash.
_C,UU
PRESENT
TIME
I -t,FtFI ._]
1. Press the /X UP or V
Figure 16
SET PRESENT TIME
OF DAY
If the words "PRESENT TIME" do not show in the display, press the SELECT button a few times until they do.
I
'
I
AM
r r.30
hardness of your water
The default is 25.
DOWN
buttons to set the
supply, in grains
per gallon.
NOTE: If your water supply contains iron, compensate
for it by adding to the water hardness number.
For example, assume your water is 20 gpg hard
and contains 2 ppm iron. Add 5 to the hardness
number for each 1 ppm of iron. In this example,
you would
PRESENT
TIME
Figure 18
HARDNESS
use 30 for your hardness
number.
PRESENT
TIME
20 gpg hardness
2 ppmironx5-(times)
10
+10
30 HARDNESS
NUMBER
Figure 17
1. Press the /X UP or V
DOWN
buttons to set the
present time. Up moves the display ahead; down
sets the time back. Be sure AM or PM is correct.
NOTE:
Press buttons and quickly
advance the display.
fast advance.
2. When
the correct
Questions?
12
bed at least every 6 months. Your local Sears
store has Water Softener Cleaner (Part Number
34427)
release to slowly
Hold the buttons down for
time is displayed,
button, and the display
"Hardness"
screen.
If your water supply contains iron, it is recommended that you clean your water softener resin
press the SELECT
available.
2. When finished setting your water's hardness number,
press the SELECT button, and the display will change
to show the "Recharge Time" screen.
will change to show the
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
SET RECHARGE
(REGENERATION)
START TIME
If you completed
the previous step, the words "RECHARGE TIME" should show in the display.
Otherwise,
press the SELECT button
several times until they do.
-J,rJ rJ AM
C.uu
RECHARGE
TIME
Figure 19
1. The softener's default recharge start time is 2:00 AM.
This is normally a time of day when water is not
being used in the household.
the softener if the household
Hard water
draws water
bypasses
during the
recharge cycle.
If a different recharge start time is
desired, press the /X UP or V DOWN buttons to
change the time, in 1-hour increments.
Be sure AM or
PM is correct.
2. When
the desired
recharge
start time is displayed,
press the SELECT button, and the display
to the normal run (time of day) screen.
oo_1
-t. i-I
i
2. rC
PM
WATER
FLOW
Questions?
Call the Kenmore
will return
Figure 20
Water
Line 1-800-426-9345
or visit www.kenmorewaterocom
13
SANITIZETHEWATERSOFTENER
1. Open salt lid, remove the brinewell cover and pour
about 3 oz. (6 tablespoons)
of household bleach into
the softener
brinewell.
Replace
2. Make sure the bypass valve(s)
(open) position.
the brinewell
allow 50 gallons of water to pass through the system. This should take at least 20 minutes. Close the
faucet.
Your new Sears softener
cover.
the water
for
is in the "service"
Press the REGENERATION
button
away, you can drain the water heater so it refills with
soft water.
If you don't drain the water heater, it will
and hold for 3 seconds, until "RECHARGE",
"Serv"
take a few days before
3. Start a recharge:
and "Fill" begin to flash in the display. This recharge
draws the sanitizing bleach into and through the
water softener. Any air remaining in the unit is
purged
ADDING
colored.
This normally occurs the first time
water runs through the resin bed. The discolored water is not harmful, and the discoloration
will not last more than a few minutes.
to the drain.
SALT TO THE STORAGE
TANK
You must keep salt in the tank, but it is not necessary
to
Untreated Water Hardness
(grains per gallon)
fill it full. Especially in humid areas, it is best to fill the
storage tank no more than half full, and to add salt
more often. Salt "bridging"
conditions are humid.
Use NUGGET
occurs
or PELLET water
more often when
softener
salt.
DO NOT
use rock salts, as they have dirt and sediments that will
stop the softener from working.
To maintain optimum
performance
of your water softener, the salt tank
should be cleaned out every 2 to 3 years.
POTASSIUM
If you choose
CHLORIDE
(I(CI)
Potassium Chloride
following these suggestions
maintenance
free service.
(KCI) as a regenerant,
will help give you years of
(the salt storage tank should contain
60 pounds of KCI at any one time).
at a time
inoperable).
3. Check the brine tank and brinewell
(black
4. If your softener does not have a KCI salt setting,
must increase your hardness setting by 25% to
Questions?
soft water.
See table
Call the Kenmore
15 gpg
19 gpg
20 gpg
25 gpg
25 gpg
35 gpg
30 gpg
40 gpg
35 gpg
45 gpg
40 gpg
50 gpg
at right.
Water
restricted
diets should con-
hard, and you drank 3 quarts of softened water you
would consume 335 milligrams of sodium. That is
equivalent
to eating
2-1/2
SOFTENING
slices of white
SALT WITH
bread.
IRON
ADDITIVES
Some salts have an additive
to help the softener
handle
iron in the water supply. These salts may be used if
your water supply has a high iron content.
It is recommended to use Sears Water Softener Cleaner (refer to
the parts list in back of manual for part number) for
tube in
salt storage tank) monthly.
If hardening is present,
pour small amounts of warm water onto hardened
areas until they loosen.
ensure continuous
7 gpg
13 gpg
REMOVING
2. A softener using KCI should not be placed in areas
with temperature
fluctuations
and high humidity (KCI
will harden in these environments and may make the
softener
5 gpg
sider the added sodium as part of their overall sodium
intake.
For example, if your water supply is 15 grains
WATER
no more than
Softener Setting when
using I(CI salt (add 25%)
10 gpg
Persons who are on sodium
SALT
1. Place only one bag of KCI in your softener
you have fully soft water.
NOTE: If this procedure is performed
on a new softener,
water coming from the taps may initially be dis-
4. After the recharge has completed, fully open a cold
water faucet, downstream
from the softener, and
14
is now softening
your household needs. However, your WATER HEATER
is filled with hard water.
To have fully soft water right
you
periodic treatments to keep your resin bed clean.
is available
at your local Sears store.
This
Persons who are concerned about their drinking water
should consider a Kenmore reverse osmosis drinking
water system that will remove in excess of 90% of the
sodium
and other drinking
Line 1-800-426-9345
water
contaminants.
or visit www.kenmorewater.com
EXTRA
RECHARGE
SALT MONITOR
SYSTEM
Sometimes, a manually initiated recharge (regeneration)
may be desired, or needed.
Two examples are:
The water softener has a salt monitor
remind you to add salt to the storage
• You have used more water
NOTE: You must set salt level each time salt is added
to the water softener.
than usual (guests visiting)
and you may run out of soft water
automatic
regeneration.
before
• You did not add salt to the softener
Add salt to the softener
before
You can start a regeneration
the next
before
it ran out.
regenerating.
immediately,
number the leveled
salt is at, or
button and hold for 3 sec-
begin to flash in the display.
"Serv"
The softener
cycle of regeneration
immediately.
will take about 2 hours to complete.
NOTE:
tank.
2. The yellow salt level decal, on the brinewell inside
the tank, has numbers from 0 to 8 (see Fig. 23).
Observe the highest
closest to.
until the words "RECHARGE",
have soft water
NOTE: The salt monitor system estimates salt levels, and
accuracy will vary with different salts.
1. Lift the salt lid and level the salt in the storage
NOW
Press the REGENERATION
light to
To set this monitor system:
or you can
set the controller to regenerate at the next preset
recharge time (2:00 AM, or as set).
RECHARGE
indicator
tank.
and "Fill"
enters the fill
This regeneration
Then, you will
Salt Level
again.
If the "Clean
Feature"
is set ON, the normal
regeneration
cycle is preceded by a cleaning
backwash and rinse. The words "CLEAN" and
"Bkwsh" or "Rinse" flash in the display, along
with the minutes of the clean cycle remaining.
_,ess
Levelk_L_
Decal
_
f_tcn'cjht Low
_"_)immediate _'i"
hold for
Figure 23
RECHARGE
3. Press the SET SALT LEVEL button
Figure 21
WATERFLOW
RECHARGE
4. If you want to turn the salt monitor off, press the SET
SALT LEVEL button past 8, until "OFF" shows in the
TONIGHT
Press and release (do not hold) the REGENERATION
button.
"RECHARGE TONIGHT"
will begin flashing
in
the display,
at
and the softener
as many times as
necessary to make the salt level bars in the display
(see Fig. 23) match the number on the decal. At
level 2 or below, the "Low Salt" indicator will flash.
will begin regeneration
display
next to the number 8.
PM
the next preset recharge time (2:00 AM, or as set). If
you decide to cancel the regeneration
before it starts,
press and release the RECHARGE button once more.
"RECHARGE TONIGHT"
will stop flashing in the display.
i OFFI
J:
IE
WATERFLOW
Figure 24
5J.r_
RECHARGE
TONIGHT
-I. I-I.M ]
ii::i
Questions?
WATER
FLOW
Call the Kenmore
Figure 22
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
15
OPTIONAL
SETTINGS:
2. Press SELECT again to display
screens shown below.
• SALT EFFICIENCY
• CLEAN
FEATURE
• CLEAN
FEATURE
• MAXIMUM
F FF
UFF
MINUTES
DAYS BETWEEN
one of the "Clean"
n
un
CLEAN
CLEAN
REGENERA-
TIONS
• 97°/o
FEATURE
• 12 / 24 HOUR
• BACKWASH
Figure 26
CLOCK
1. To set any of these options,
for 3 seconds
CLEAN: This feature
& FAST RINSE TIMES
until "000"
press and hold SELECT
shows in the display.
press (do not hold) SELECT again to display
the "Salt Efficiency" screens shown below.
t' FF
UFF
one of
water
softener
When
Figure 25
this feature
will operate
DOWN
buttons to change
Press SELECT again to display
screen shown below.
the "Clean
is ON, the
at salt efficiencies
between
TIME
Figure 27
California
Efficiency
CLEAN
FEATURE
Clean
Feature
cycle
OFF and ON.
can
this
time
To change
this
cycle
the time,
time.
If you
the length
adjust
en the
Your Kenmore Water Softener has a "High
Efficiency"
feature that can be set ON or OFF.
MINUTES:
ON,
automatically
increase
Requirement
Time"
CLEAN
salt dosage and less water. This softener is shipped
with the efficiency feature set OFF. Installations
in
the State of California require this setting to be
turned ON. Use the /X UP or V DOWN buttons to
between
MIN
of
4000 grains of hardness per pound of salt or higher.
The softener may recharge more often using smaller
change
the
extra
supply does not contain iron or sediments, be sure
this feature is set to OFF. The default is OFF. Use
.
SALT EFFICIENCY:
supplies
cleaning of the resin bed before it is regenerated
with the salt brine. To conserve water, if your water
the /X UP or V
OFF and ON.
Icon
on water
and fast rinse cycle will occur first, preceding
normal regeneration
sequence.
This provides
Then
FI
Efficiency
is beneficial
containing iron and/or
high amounts of sediments
(sand, silt, dirt, etc.). When set to ON, a backwash
have
of the
set the
extra
backwash
is set to 2 minutes.
However,
from
in length.
1 to 15 minutes
time,
or the
If no change
use the
V
/_
DOWN
is desired,
UP button
button
step.
capacity while most often achieving maximum salt
efficiencies.
When installing this unit in the State
of California,
you MUST turn the efficiency feature
ON. The softener may initiate more frequent
Questions?
16
at 4000
Call the Kenmore
grains
Water
per
Line 1-800-426-9345
to
to short-
continue
This softener is shipped with the efficiency
feature
set OFF, which will utilize the maximum rated
recharges, but it will operate
pound of salt or higher.
you
or visit www.kenmorewater.com
to
next
4. Press SELECT again
to display
the "Recharge
Days"
screen.
6. Press SELECT again
to display
the "12 or 24 hr"
screen.
r
RECHARGE
C!
AM
r
RECHARGE
TIME
DAY
Default
Display
_
DAY ]
between
regenerations
12 OR 24 HOUR CLOCK: All time displays are shown
in standard clock time (1 to 12 AM; and 1 to 12 PM)
Figure 28
MAXIMUM
Figure 30
Example:
Set to 4 days maximum
DAYS BETWEEN REGENERATIONS:
electronic controller automatically
eration frequency.
This provides
determines
the greatest
at the 12 hr default setting. If 24 hour time format
desired, set to 24 hr by pressing the UP f button.
The
regenoperat-
7. Press SELECT again
to display
the alternating
O0
set this feature to force a regeneration
every set
number of days. You may want to do this if, for
buttons
to change
a_
Bk wsh
TIME
TIME
to display
the "97%"
screen.
Figure 31
BACKWASH & FAST RINSE TIMES: If you experience
salty tasting water after regeneration,
you may need
to increase the backwash and fast rinse times. The
cycle times during
nEE
UFF
RECHARGE
MIN
the number of
days (up to 6).
5. Press SELECT again
n}
MIN
Bk wsh
example, your water supply contains iron and you
want the softener to regenerate at least once every
few days to keep the resin bed clean. Use the f
DOWN
screens
shown in Figure 31.
ing efficiency and, under most conditions this feature
will be left in its default mode. However, you can
UP or V
is
RECHARGE
regenerations
are determined
by
the softener's electronic controller.
However, you may
increase the backwash and fast rinse times, in 1
minute increments.
If you wish to increase the backwash time, use the f UP button to add up to 15 min-
Figure 29
utes to the backwash time. Then press SELECT to display the alternating
screens shown in Figure 32.
w
97°/o FEATURE: The 97%
H OOM'N
I1
Feature can save salt and
water by regenerating
when 97% of the softener's
capacity has been used up. With this feature ON,
the regeneration
can occur at any time (whenever
Rinse
TIME
Rinse
the system has reached 97% of its capacity).
The
default is OFF. If this feature is desired, turn it on by
pressing the UP f
button.
f UP button
rinse time.
the fast rinse time, use the
to add up to 15 minutes to the fast
8. Press SELECT to return to the normal
day) screen.
Call
the
Kenmore
Water
TIME
_N
Figure 32
If you wish to increase
Questions?
0}
U
Line 1-800-426-9345
or visit
run (time of
www.kenmorewater.com
17
TANK LIGHT
PROGRAM
To light the the inside of the salt storage tank, press the
TANK LIGHT button on the faceplate.
Press this button
If electrical power to the softener goes off, the time display is blank but the electronic controller keeps the cor-
again to turn the light off.
ically after 15 minutes.
rect time for several hours. When electrical power
comes on again, you will have to reset the present time
It will also turn off automat-
MEMORY
only if the display is flashing.
The HARDNESS and
RECHARGE TIME never require resetting unless a
change is desired.
Even if the clock is incorrect after a
long power outage, the softener works as it should to
Tank Light
Icon
Figure 33
WATER
FLOW
keep your water soft, however, regenerations
may occur
at the wrong time of day until you reset the clock to the
correct
WATER
FLOW THROUGH
If soft water is in use, the water flow bars continually
scroll across the display.
The bars scroll slowly when
water flow is slow, and move faster as water flow
increases. The flow bars do not show when all faucets
and water
using appliances
are off.
Flow bars scroll when soft water
6
The ultra cleansing feature keeps larger particles of
sediment from entering the home's plumbing system.
screen clean.
IMPORTANT:
POSITION
TIME
REMAINING
34
is OFF.
The ultra cleansing feature is not intended
to replace pretreatment
filtration.
For
indicators (Serv, Fill, Brine,
while the softener is recharg-
sediment
filtration
products.
Ultra Cleansing
Screen
Resin
Tank
return to service appears in place of the present time.
When the valve is moving from one cycle to another,
indicators
The default
Sears offers a full line of dedicated
ing. RECHARGE flashes in the display and, beginning
with Brine, the minutes of recharge remaining before
both position
The
for
problem water applications,
additional
sediment filtration is recommended.
& VALVE
INDICATORS
One of the valve position
Bkwsh, Rinse) is displayed
As
water passes through the softener, the larger sediment
particles are collected in the integrated
basket and
cleansing
WATERFLOW
Figure
RECHARGE
FEATURE
screens. The "Clean Feature" may be turned ON to
provide an extra backwash that will help keep the ultra
mm
WATERFLOW
ULTRA CLEANSING
water using appliances by reducing the chance of larger particles entering the various products valves and
5
8
KENMORE'S
then rinsed to the drain before each regeneration.
ultra cleansing feature provides added protection
is in use
]: 2
7
_4
_3
_2
time of day.
THE SOFTENER
7
are flashing.
Recharge
Time
Valve
Position
Indicator
Remaining
Figure 35
Top
Distributor
Figure 36
Questions?
18
Call
the
Kenmore
Water
Line 1-800-426-9345
or visit
www.kenmorewater.com
SALTBRIDGE
Sometimes,
brine tank.
a hard crust or salt "bridge"
forms in the
It is usually caused by high humidity or the
wrong kind of salt. When the salt "bridges,"
an empty
space forms between the water and the salt. Then, salt
will not dissolve in the water to make brine. Without
brine, the resin bed is not recharged
will result.
gently
to the rim of the water
push the broom
handle
\\
to break _"_t
1"-2"
and hard water
If the storage tank is full of salt, it is difficult to tell if
you have a salt bridge.
A bridge may be underneath
loose salt. Take a broom handle, or like tool, and hold
it next to the water softener. Measure the distance
from the floor
Push tool into
salt bridge_
softener.
straight
Pencil
Mark
Salt
Then,
down into the
salt. If a hard object is felt before the pencil mark is
even with the top, it is most likely a salt bridge.
Gently
Broom J
_.
push into the bridge in several places to break it. Do
not use any sharp or pointed objects as you may punc-
_
w_._
ture the brine tank. Do not try to break the salt bridge
by pounding on the outside of the salt tank. You may
damage
ALWAYS
•
MAKE
THESE INITIAL
If display
tener.
CHECKS
show the correct
is blank, check
power
Level
Empty
Space
Figure 37
FIRST
time of day?
source to the sof-
If time is flashing,
power
was off for a long peri-
If an error code (example:
"Err3")
operation
time.
but
shows in the dis-
play, go to "Troubleshooting".
2. Are bypass valve(s)
4. Is the softener's transformer
plugged
grounded wall outlet, and the power
securely to the controller?
Call the I<enmore
to the sof-
into a "live",
cable fastened
Water
7. Is the brine tubing
to nozzle/venturi
tank?
connected?
Brine tubing
and brine valve
connects
assembly.
8. Press the SELECT button twice to display the hardness setting. Make sure it is correct for the household's water supply. Perform a hardness test of the
untreated incoming water and compare with the
fully in service position?
3. Are the inlet and outlet pipes connected
tener inlet and outlet respectively?
Questions?
5. Is the valve drain hose free of kinks and sharp bends,
and not elevated more than 8 ft. above the floor?
6. Is there salt in the storage
od. The softener resumes normal
regenerations
occur at the wrong
•
Water
the tank.
1. Does the time display
•
Salt Bridge
Handle
hardness setting. Also test a soft water sample to
verify if a problem exists. Press the SELECT button
several
Line 1-800-426-9345
more times to return to present time display.
or visit www.kenmorewater.com
19
TROUBLESHOOTING
If your water softener does not work properly, make the following easy checks. Often, you will find what
yourself and you won't have to call and wait for service.
If you do not find anything wrong while making
and your softener
still does not work properly,
PROBLEM
No soft water
level
Department.
CAUSE
No soft water
No soft water
play is blank
call your Sears Service
No salt in the storage
& dis-
& salt
not dropping
CORRECTION
tank.
Add salt and then use RECHARGE
feature.
Check for loss of power and correct.
Reprogram electronic control and then use
RECHARGE NOW feature.
Fuse blown, circuit breaker tripped, or circult switched off (see "Power Outage
Memory").
Replace fuse, reset circuit breaker, or switch
circuit on, and then use RECHARGE NOW
feature.
Salt storage
tank "bridged".
Bypass valve(s)
Dirty, plugged
turi assembly
water
Valve drain
Refer to "Breaking
in "bypass"
or damaged
Move
nozzle &ven-
Take apart, clean and inspect nozzle & venturi (see instruction decal under salt lid).
hose is plugged
water
Incorrect
time set.
Incorrect
water
a Salt Bridge".
position.
or restricted.
bypass valve(s)
blockage
Check and change
hardness
set.
to "service"
position.
Hose must not have any kinks, sharp bends or
any water flow
Requirements").
hard
NOW
Transformer
unplugged at wall outlet, or
power cable disconnected
from back of
electronic board or transformer
malfunction.
No soft water & salt
storage tank full of
Intermittent
is wrong
the checks,
Refer to "Set Water
(See "Valve
Drain
time setting.
Hardness
Number"
to
set correctly.
Hot water being
regenerating,
used when softener
Possible increase
in water
is
hardness.
Avoid using hot water while the softener is
regenerating,
as the water heater will fill with
hard water.
Test untreated
water
for hardness
and iron.
Program the water softener accordingly
"Set Water Hardness Number").
Brine tank flooded
Valve drain
Dirty, plugged
turi assembly,
hose is plugged
or damaged
or restricted.
nozzle &ven-
Salty tasting water
immediately after
Backwash and fast rinse cycle times are not
long enough.
regeneration
Valve drain
hose is plugged
or restricted.
Hose must not have any kinks, sharp bends or
any water flow blockage (See "Valve Drain
Requirements").
Take apart, clean and inspect
turi (see "Cleaning the Nozzle
Questions?
2O
Fault in electronic controller or wiring harness connections to position switch, position
switch inoperable
or motor inoperable,
Call the Kenmore
Water
Line 1-800-426-9345
nozzle & ven& Venturi").
Increase backwash & fast rinse times (see
"Back Wash & Fast Rinse Times").
Hose must not have any kinks, sharp bends or
any water flow
Requirements").
Error code appears
(example:
"Err3")
(see
blockage
(see "Valve
Drain
Unplug power cord. Check all wiring connections to be sure they are secure. Plug in
power cord and wait 6 minutes. If error
code returns, call I<enmore Water Line.
or visit www.kenmorewater.com
MANUALLY
INITIATED
ELECTRONIC
DIAGNOSTICS
1. To enter diagnostics, press the SELECT button and
hold for three seconds. The display will change to
show turbine count, valve cycle position,
switch status (open or closed).
and position
Motor
Turbine Count
Valve Position
Indicator
Turbine Count
(No Water
Flowing)
(Water
Flowing)
Position
Sensor
Switch
s
uuu!
_4
1
j
Housing
I
Turbine
I
Turbine
Support
& Shaft
Im12
WATERFLOW
Valve Outlet
Position Switch
Indicator
TURBINE
Figure 38
Figure 39
(Open)
OPERATION:
If no water
is flowing
through
NOTE: If the electronic
controller
is left in the diagnos-
the softener, the turbine indicator displays three zeros.
When water is flowing, a 000 to 199 count repeats for
tic display (or a flashing display when setting
times or hardness), the normal time of day dis-
each gallon of water passing through the turbine.
To
check for positive operation of the turbine if zeros are
play automatically
returns if a button has not
been pressed for 4 minutes. To return to the
shown, open a nearby soft water faucet and observe
the turbine count. If you don't get a reading in the dis-
diagnostic
play with faucet open, pull the sensor housing from the
valve outlet port (see Fig. 39). Pass a small magnet
back and forth in front of the sensor. You should get a
reading in the display.
If you get a reading, unhook the
inlet and outlet plumbing
binding.
POSITION
SWITCH
and check the turbine
STATUS: With
the valve
RESETTING
display,
repeat
TO FACTORY
step 1, above.
DEFAULTS:
To reset the electronic controller to its factory
for all settings (time, hardness, etc.):
default
1. Press the SELECT button and hold it until the display
changes twice to show the flashing model code.
for
in service,
2. Press the /X UP button to display
a flashing
"SOS".
or any of the recharge cycle positions, the position
switch indicator will show the switch open. While the
valve is rotating from one position to another, the position switch indicator will show the switch closed. There
is likely a problem
if indications vary from this pattern.
OTHER INFORMATION:
While
in the diagnostics
screen, the following information is available
and may
be beneficial
for various reasons. This information
is
retained
by the electronic
electrical
•
power
controller
is applied
from the first time
to the unit.
Press and hold the /X UP button
ber of days this controller
to display
has had electrical
the num-
Figure
3. Press the SELECT button,
will restart.
and the electronic
40
controller
4. Set the present time, hardness, etc., as described
pages 12 & 13.
on
power
applied.
•
Press and hold the V
DOWN
button
to display
the
number of regenerations
initiated by this controller
since the model code number was entered.
Questions?
Call the I<enmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
21
MANUAL
ADVANCE
REGENERATION
CHECK
This check verifies proper operation of the valve motor,
brine tank fill, brine draw, regeneration
flow rates, and
other controller functions.
Always make the initial
checks first, and perform
the manually
initiated
Position Markers
(valve in service)
elec-
tronic diagnostics.
NOTE: The display must show a steady time (not flashing). If an error code shows, first press the
SELECT button to enter the diagnostic
1. Press the REGENERATION
seconds.
"RECHARGE",
button
"Serv"
display.
®
©
and hold in for 3
and "Fill"
flash in the display as the softener
cycle of regeneration.
begin to
enters the fill
Motor
o
O
Figure 41
does not enter the tank, look for an
obstructed
nozzle, venturi,
or brine valve
NOTE: If water system pressure is low, an elevated
drain hose may cause back pressure, stopping
brine draw.
fill flow plug, brine tubing,
riser pipe.
4. After observing fill, press the REGENERATION
button
to move the softener into brining.
A slow flow of
5°
®
Cam
2. When valve reaches "Fill" position, remove the
brinewell cover and, using a flashlight, observe fill
water entering the tank.
3. If water
O
water to the drain will begin. Verify brine draw
from the brine tank by shining a flashlight into the
6. Again press REGENERATION to move the softener
into backwash.
Look for a fast flow of water from
the drain hose.
brinewell and observing
uid level.
7. An obstructed
tor, backwash
If the softener
a noticeable
does not draw
venturi
drop in the liq-
brine:
•
nozzle and/or
•
nozzle and venturi
•
•
restricted drain (check drain fitting
ineffective
nozzle and venturi seal
•
other inner valve
8. Press REGENERATION
dirty
not seated
problem
properly
on gasket
to move the softener
brine that may remain
and hose)
brining
(rotor seal, rotor & disc,
SCHEMATIC
top distribuinto fast
rinse. Again look for a fast drain flow. Allow the
softener to rinse for a few minutes to flush out any
in the resin tank from the
cycle test.
9. To return the softener
TION once more.
wave washer, etc.)
WIRING
flow indicates a plugged
flow plug or drain hose.
to service, press REGENERA-
Back of Controller (PWA)
AC INPUT
_
POS. / TURBINE
MOTOR
__ _±L_____B__L_
Valve
Transformer
Turbine
Sensor
Questions?
22
Call
the
grn
brn
I<enmore
Water
Line 1-800-426-9345
&
_O
NO
NC
or visit
Position
Switch
Figure
www.kenmorewater.com
42
Questions?
Call the I<enmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
23
1
2
3
\
\
27
Rating Decal
Location
"_.'_
7
2O
19
28
8
18
9
17
1(
29
\A
i
I
I
12
13
', 1/[
j
14
3O
't
!
Questions?
24
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
Key
No.
Part No.
Description
Key
No.
24V, 1OVA
17
7327584
Repl. Bottom Distributor
18
0502272
Resin
1
7275907
Transformer,
2
7325168
Top Cover
3
7325223
Salt Lid (order
7325231
Instruction
Decal,
7325257
Instruction
Decal, Spanish
4
7327827
Repl. Electronic
5
7325134
Faceplate
(order
•
7325142
Faceplate
Decal
6
7325388
Rim
7
7265025
Ultra
decal below)
English
Controller
decal
(PWA)
below)
•
7112963
Distributor O-Ring Kit
(includes Key Nos. 20-22)
20
_h
O-Ring,
2-3/4"
21
_h
O-Ring,
13/16"
x 1-1/16"
22
_h
O-Ring,
2-7/8"
x 3-1/4"
7077870
Top Distributor
7141001
Vapor
Barrier
Clamp
Section
26
7088033
Retainer
27
7248706
Grounding
Nut, 1/4"
28
7171349
Cone Screen
1/4"
29
7310202
Brine Valve Assembly
7327576
Brinewell Mounting Hardware
(includes Key Nos. 9-11)
Cover
9
_h
Wing
10
_h
O-Ring,
11
_h
Plastic Screw, 1/4-20
x 1/2"
x 5/8"
Brinewell Assembly
(includes Key Nos. 12 & 13)
12
_h
Brinewell
13
_h
Decal, Salt Level
14
7324879
Salt Storage
15
1103200
Adaptor
Tank
Kit
(2 req.)
Clip (2 req.)
Kit
30
7327568
Float, Stem & Guide
•
3442707
Water
•
7278573
Parts
5 ea.
2 ea.
1 ea.
•
7325207
Owner's
•
Not illustrated.
Softener
Assembly
Cleaner
"/€
Bag (includes
of Key No. 69,
of Key Nos. 57 & 70,
of Key Nos. 15, 16, 27 & 97)
Manual
Elbow
Grommet
•/€ Not included with water
Questions?
x 3"
7176292
•
9003500
Repl. Resin Tank, 8" x 40"
25
Screen
Brinewell
16
7113058
24
Cleansing
7219888
7214375
Description
19
23
8
•
Part No.
Call the Kenmore
Water
Line 1-800-426-9345
softener.
or visit www.kenmorewater.com
25
52
51
95
96
9493__
!
54
J
55
90
_
_ 62
61
Cross-Section
_" 67
View
8_\
68
63
77
t
80
79
78
75
76
Questions?
26
Call
the
Kenmore
Water
Line 1-800-426-9345
or visit
www.kenmorewater.com
Key
No.
Part No.
Description
50
7224087
Screw, #8-32
51
7286039
Motor
52
0900857
Screw, #6-20
Key
No.
Part No.
Description
x 1" (2 req.)
76
7082053
Valve
(incl. 2 ea. of Key No. 50)
77
7081201
Retainer, Nozzle
78
7170319
O-Ring,
79
7081104
Housing,
x 3/8"
(2 req.)
Plate
Body
1/4"
53
7231385
Motor
54
0503288
Bearing
80
1202600
Nut - Ferrule
55
7284964
Cam & Gear
81
7095030
Cone Screen
56
7142942
Clip, Drain
82
Nozzle
& Venturi
7204362
Gasket
(only)
84
0521829
Flow Plug, 0.1 gpm
85
7146043
Screen
86
7167659
Screen Support
x 5/8"
87
7170262
O-Ring,
x 15/16"
88
7199729
Cap
89
7309803
Wire
90
7085263
Valve
x 9/16"
91
7074123
Screw, #10-14
& Venturi
92
7077472
Expansion
93
7030713
Switch
(2 provided)
58
7024160
Adaptor,
59
7170327
O-Ring,
60
0501228
Flow Plug, 2.0 gpm
•
7129716
Seal Kit, (includes
83
Drain Hose
5/8"
7/16"
62
_
O-Ring,
3/4"
63
_
O-Ring,
3-3/8"
64
/h
Rotor Seal
65
_
O-Ring,
66
_h
Seal, Nozzle
x 13/16"
Key Nos. 61-66)
x 3-5/8"
3/8"
Gasket
Kit
x 1-3/8"
Harness (Sensor)
Cover
x 2" (5 req.)
Pin
67
7082087
Bearing, Wave
68
7199232
Rotor & Disc
94
7117816
Spacer
69
7116713
Clip (4 req.)
95
7070412
Screw, #4-24
(2 req.)
96
7254260
Installation Adaptor Kit,
(includes 2 ea. copper tubes, nuts,
clips & washers) "/t
70
7278442
Washer
1-1/8"
(2 req.)
& Venturi
Flow plug, 0.3 gpm
Tubing Clamp
O-Ring,
Nozzle
1148800
0900431
_
x 3/8"
7187772
57
61
& Venturi
Installation Adaptor, 1" NPT (2 req.,
includes 2 ea. of Key No. 71)
15/16"
x 1-3/16"
(2 req.)
x 1-1/8",
Flat Head
71
7170288
O-Ring
72
7092642
Plug, Drain Seal
73
7129889
Spring
97
7278434
Bypass Valve Assembly
(includes 2 ea. of Key No. 71)
•
7113040
Turbine & Support Assembly
(includes 1 ea. of Key Nos. 74, 75
& 2 ea. of Key No. 71)
•
7187065
Nozzle & Venturi Assembly
(includes Key Nos. 79 & 81-88)
74
_
Turbine Support
•
7139999
Drain Tubing, 3/8"
75
_
Turbine
•
7123613
Silicone
Grease
•
42-34405
Flexible
Connectors,
3/4"
•
42-34407
Flexible
Connectors,
1" "/t
& Shaft
•
Questions?
(for O-Rings)
"/t
"/t
Not illustrated.
Not included with water
71
I.D. x 20 ft.
softener.
97
Call the Kenmore
Water
Line 1-800-426-9345
or visit www.kenmorewater.com
27
Your Home
For expert troubleshooting
and home solutions advice:
managemylife
Our Home
For repair of carry-in items like vacuums, lawn equipment,
and electronics, call anytime for the location of your nearest
Sears Parts & Repair Service
1-800-488-1222
(U.S.A.)
1-800-469-4663
www.sears.com
To purchase
agreement
(U.S.A.)
Para pedir servicio de reparaci6n
a domicilio, y para ordenar piezas:
1-888-SU-HOGAR
on a product serviced
1-800-361-6665
Au Canada
®
(1-888-784-6427)
www.sears.com
® Registered Trademark
® Marca Registrada
(Canada)
www.sears.ca
a protection
1-800-827-6655
Center
by Sears:
(Canada)
pour service en frangais:
1-800-LE-FOYER
Mc
(1-800-533-6937)
www.sears.ca
/ TNTrademark of KCD IP, LLC in the United States, or Sears Brands, LLC in other countries
/ TNMarca de Fabrica de KCD IP, LLC en Estados Unidos, o Sears Brands, LLC en otros parses
NCMarque de commerce
/ ND Marque depos6e de Sears Brands, LLC
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement