continued | Manualzz

HITACHI
Liquid Crystal Projector
Model
C P-X960WA / 970W
USER'S GUIDE
Thank
you for purchasing
the Hitachi
liquid
thoroughly
to ensure correct usage through
manual in a safe place for future reference.
Outline
NTSC/PAL/SECAM
video signals
onto a
screen. Little space is required for installation
and large images
can easily be realized.
(1) Outstanding
brightness
lamp
and high-efficiency
optical
system assure a high level of brightness.
(2) Partial magnification
Distortion-free
Please
After
read this user's
reading,
correction
function
images are quickly available.
(4) Power zoom and power focus.
(5) P in P function
(6) USB jack
Checking
for
manual
store this instruction
Page
Before Use ................................................
the package
Contents
3
................ 8
Names and functions of each part ............ 8
Installation
..............................................
12
Basic operations
......................................
and functions
......................
13
17
Connection
to the video signal
terminals ................................
22
Connection
to the RGB signal
terminal ..................................
22
Connecting
Connection
function
Interesting parts of images can be magnified
closer viewing.
(3) Distortion
understanding.
Adjustments
Features
UHB
projector.
Contents
This liquid crystal projector is used to project
various
computer
signals
as well
as
The
crystal
to the USB ............................
to the CONTROL signal
terminal ..................................
setup ........................
25
26
Example
of system
Cleaning
Lamp
the air filter ................................
..............................................
31
32
31
Message
table ..........................................
32
When you think something wrong ............ 33
Specifications
..........................................
34
About the warranty and
after-service
..........................
35
/
_
About Trademarks
t
• VGA and XGA are trademarks
of IBM (International
Business Machines Corporation).
• Macintosh is a registered trademark of Apple Computer
• VESA and SVGA are trademarks
• Windows95 and Windows98
Corporation of the U.S.
or registered trademarks of Video Electronics
Standards association.
are registered trademarks of Microsoft Corporation in the U.S. and other countries.
Carefuly observe the trademarks
and registered trademarks of all companies,
even when not mentioned.
FOR THE CUSTOMERS IN U.K
TH1S PRODUCT
IS SUPPLIED
FOR THE U.K PLEASE
WlTH
A TWO PIN MAINS
REFER TO THE NOTES
IMPORTANT
WORDING
is supplied
EUROPE.
ON THIS PAGE.
FOR UNITED
FOR CLASS I EQUIPMENT
The mains lead on this equipment
PLUG FOR USE IN MA1NLAND
KINGDOM
INSTRUCTION
with a moulded
BOOKS AND LABELS
plug incorporating
a fuse, the value of which is
indicated on the pin face of the plug. Shoud the fuse need to be replaced, an ASTA or BS1 approved BS 1362
fuse must be used of the same rating. If the fuse cover is detachable never use the plug with the cover omitted.
If a replacement fuse cover is required, ensure it is of the same cotour as that visible on the pin face of the plug.
Fuse covers are available from your dealer.
DO NOT cut off the mains plug from this equipment. If the plug fitted is not suitable for the power points in
your home or the cable is too short to reach a power point, then obtain an appropriate safety approved extension
lead or consult your dealer.
Shoud it be necessary to change the mains plugs, this must be carried
qualified electrician.
If there is no alternative
removed
out by a competent
to cutting off the mains plug, ensure that you dispose
the fuse, to avoid a possible
shock hazard by inadvertent
WARNING: THIS EQUIPMENT
IMPORTANT:
connection
person,
of it immediately,
preferable
having
a
first
to the mains supply.
MUST BE EARTHED
The wires in the mains lead are coloured in accordance with the following code:
Green and Yellow = Earth, Blue = Neutral, Brown = Live.
Green & Yellow to Earth
Brown to Live
Fuse
Blue to Neutral
1El
Cord Clamp
As these colours
as follows:
may not correspond
The wire which is
with the letter E or
The wire coloured
BLACK. The wire
BROWN
or RED.
with the coloured
makings
identifying
the terminals
in your plug, proceed
coloured Green and Yellow must be connected to the terminal in the plug which is marked
by the earth symbol @ or coloured Green or Green and Yellow.
Blue must be connected to the terminal marked with the letter N or cotoured BLUE or
coloured BROWN must be connected to the terminal marked with the letter L or coloured
WARNING:
device,
against
This equipment
has been tested and found to comply
with the limits for a Class A digital
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
harmful interference when the equipment is operated in a commercial environment.
This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
instruction manual, may cause harmful interference to radio communications,
a residential
interference
area is likely to cause harmful
at his own expense.
interference
and used in accordance with the
Operation of this equipment in
in which case the user wilt be required
to correct the
]/
Instructions to Users:
This equipment complies with the requirements
equipments provided that following conditions
(1) Video
signal
of FCC (Federal
are met.
Communication
Commission)
Class A
cables:
Double shielded coaxial cables (so called FCC shield cable) must be used and the outer shield must be
connected to the ground. Or, if normal coaxial cables are used, the cables must be enclosed in metal pipes
or similar way to reduce the interference
(2) Power cord:
Shielded power cord must be used.
(3) Video
noise radiation.
The outer shield must be connected
to the ground.
inputs:
The input signal amplitude
must no exceed the specified
level.
Before Use
<Before
Using>
About the Symbols
Various symbols are used in this instruction manual and on the product itself to
ensure correct usage, to prevent danger to the user and others, and to prevent
property
important
contents.
damage. The meanings
of these
that you read these descriptions
Warning
Caution
This symbol
indicates
result in personal
symbols
are described
below.
thoroughly
and fully understand
information
that, if ignored,
It is
the
could possibly
injury or even death due to incorrect
handling.
This symbol indicates information
that, if ignored, could result
possibly in personal injury or physical damage due to incorrect
handling.
Typical Symbols
This symbol
indicates
an additional
warning
illustration
is provided to clarify the contents
indicates danger of electrical shock).
(including
cautions).
(the illustration
An
to the left
indicated in an illustration or nearby (the symbol to the left indicates that
This symbol indicates a prohibited
action. The contents will be clearly
disassembly is prohibited).
indicated in an illustration or nearby (the symbol to the left indicates that
This symbol indicates a compulsory
action. The contents will be clearly
the power plug should be disconnected from the power outlet).
3
[Safety Precaution]
• If a problem
should
occur.
• Do not insert
If smoke or a strange odor arise, continued
use could result in fire or electrical shock. In
foreign
objects.
switch and then disconnect
the power plug
from the power outlet. After making sure that
Do not insert metal objects through
the ventilation
openings,
etc., of
this projector or drop such objects
inside because this could result in
fire or electrical shock.
the smoke or odor has stopped, contact your
dealer for repairs. Never attempt
to make
repairs yourself because this is dangerous.
If a foreign
object should enter this
projector, immediately tum off the power
switch,
disconnect
the
Do not use this projector
power
power
such
case,
immediately
turn off the power
if
there
is no image
or
sound, or if the sound is
distorted.
Continued
use
could
result
in fire or
electrical
Disconnect the
plug from the
power outlet.
shock.
In such case, immediately turn off the power
switch, disconnect
the power plug from the
power outlet and contact your dealer.
If water should
enter the inside
projector,
immediately
turn
of this
off the power
switch, disconnect
the power plug from the
power outlet and contact your dealer.
• Do not install on an unstable
Do not install this projector
surface.
on an
A
unstable surface such as a wobbly
stand or incline because this could
result
in the projector
falling
_'_
k,N
and
causing injury.
• Do not open
your dealer.
Continued use could
Disconnectthe
result in
plug from
fire or electrical
shock. Use
special caution in households
where children
• Do
not
when
look
the
the cabinet.
open the cabinet.
There
inside
is high canvoltage
which
cause
are present.
through
lamp
the
lens
_
V
is on.
Never look through the lens when the
lamp is on. The powerful light could adversely
affect vision. Use special caution
where children are present.
in households
• Avoid shock or impact on the projector.
If the
projector
resulting
cabinet,
should
in damage
immediately
fall,
to the
turn off
Disconnect the
plug from the
power outlet.
outlet and contact your dealer.
Continued
use could result in
fire or electrical shock.
_
shock.
the
power outlet.
the power switch, disconnect
the power plug from the power
Never
electrical
plug
from
the
outlet and contact
Donot
Electricshock
Contact your dealer for disassemble, hazard.
internal inspection, adjustment and
• Do
not
place
a container
this
projector
containing
in
liquid.
Do not place flower vases, flower
pots, cups, cosmetics,
liquids
repair.
• Do not modify.
_._
such as water, etc., on top of this projector.
Spillage could result in fire or electrical shock.
Do not modify this projector because
Do not
this could result in fire or electrical shock, disassemble"
• Use
• Do not use in the bathroom.
Do
not
use
this
projector
bathroom
because this could
fire or electrical shock,
4
/_
in the
result
in De net use near
water.
only
the
indicated
power
supply.
Use only
the
indicated
power
supply. The use of any other power
could result in fire or electrical shock.
supply
•
Handle the power cord with care.
_Do
not damage,
cut,
process
• High
or
strongly twist the power cord. Placing
heavy objects on the power cord, heating or
strongly pulling the power cord can result
damage as welt as fire or electrical shock.
• Pulling on the power cord
temperatures
are generated
when
the lamp is lit, so do not place objects
front of the lens.
_.
in
A
• Placing heavy objects on the power cord /r_'_
• Damaging the cord
k,Y
• Placing near heaters
Do not position
cord under
the
the power
projector.
This can
damage the power cord and cause fire or
electrical shock. Also, do not place a spread,
cover, etc., over the power cord because this
could result in the inadvertent
placing
of
heavy objects on the concealed power cord.
If the
power
cord
(exposed
or broken
etc.), contact
your
is damaged
core wires,
dealer
for
/g|_k
/.'x
replacement;
otherwise,
fire or
electrical shock could result.
Make sure there is no dust, etc., on the power
plug and insert a knife blade to make sure that
there is no looseness.
• Do not allow the laser beam to enter the
eyes.
This remote control is equipped with a
laser pointer and a laser beam is emitted
from the laser outlet. Do not look directly
into the laser beam outlet or direct the
laser beam at other people.
Vision can be impaired if the laser beam
enters the eyes. Especially pay attention if
children are present.
®
Laser beam outlet
in
/
• Do
not
this
sit
or place
heavy
objects
•
projector.
Do not sit on this projector.
where children are present.
Do not place heavy
projector.
Placing
heavy
objects
_"_
Do not block the ventilation
or falling
openings.
and
purposes,
could result
on its
plug
from
the
before
starting
maintenance
the
sure
terminals
the
or dusty
in a humid
near
a humidifier
the
or other
locations
where there is oily smoke or humidity.
This could result in fire or electrical shock.
• Use the caster brakes.
When
power
installing
this projector
on a stand
moving
with
overturning
personal
Do not handle
plus
and
aligned
due to battery
A
and
injury.
the power
cord roughly.
*Keep
the power
cord
away
from
heaters
because
the heat could melt the
A
Do not touch the power plug
with wet hands because this
_'_
could result in electrical
or personal
cracking
or
are correctly
•
or
power cord and cause fire or electrical
batteries
when loading
the batteries,
Incorrect
loading could result in
personal injury or contamination
of
the surroundings
leakage.
installation
kitchen,
causing
this projector.
Do not mix old
and new batteries
because
this
6
_Avoid
t,N
of this projector.
• Battery
usage.
Use only the specified
leakage.
_Make
in humid
about
or dusty location.
This could
result in fire or electrical shock.
power
outlet
the care and
result
in fire
due to battery
installation
Do not install this projector
in
Disconnect the
plug from the
power outlet.
could
injury
Avoid
for details
with casters,
use the caster
brakes
to prevent
the stand
disconnect
the
locations.
maintenance.
For safety
of dust inside
in fire
or A
season, etc. Ask your dealer
internal cleaning.
•
etc. Also, when installing this projector, make
sure the ventilation openings are at least 30cm
from the wall.
Care
Accumulations
can result
more effective
if performed
befor
every humid periods
such as rainy
projector
place this projector
on a carpet or
bedding or cover it with a table cloth,
once
/,'x
on this
side during use or push it into a small,
poorly
ventilated
location.
Do not
interior
malfunction
if not cleaned
for an /€|_
extended
period.
This cleaning
is
Do not block the ventilation
openings of
this projector. Blocking ventilation could lead
to internal overheating
which
fire. Do not place this projector
projector
two years.
years.
projector
objects
on this
the
Request your dealer to clean the interior
of the projector approximately
every two
A
could result in loss of balance
and cause personal
injury.
•
Clean
every
This could result in overturning,
leading to damage or personal injury.
Use special caution in households
•
on
_When
power
shock.
shock.
disconnecting
the
plug, do not pull on the power
minus
cord. This could damage the power cord and
cause fire or electrical shock. Always grip the
A
plug when disconnecting.
f|_k
cracking
or
•
When
the
projector
for an extended
•
is not to be used
/
the projector.
When moving the projector, be sure _1_
to replace lens cap, disconnect
the
power plug from the power outlet
and disconnect
all external
Disconnect
period.
For safety
purposes
when
the
projector
is not to be used for an
extended period because of travel,
etc., always disconnect
the power
Moving
plug
plug from the power outlet. Also
power outlet.
close the lens cover to prevent the lens
connections.
Failure to do this
could damage the power cord
and cause fire or electrical shock.
surface being scratched.
Avoid
Disconnect the
plug
from
the
any impact
because
or shock
the
from
power outlet.
to the projector
this could result in malfunction.
When moving
this projector
outdoors,
protect
it from wetting due to rain, etc. If the
projector should become wet, dry it
thoroughly
before
further
use. I_1._
Continued
use while
wet could
result in fire or electrical shock.
[General Cautions]
•
Avoid
excessively
Do not place
•
hot locations.
this projector
in direct
sunlight or near a hot object such as a
stove, etc., because
the heat could
have adverse influence on the cabinet
Cabinet
care.
The cabinet is made of plastic and discoloration
or paint peeling can occur if wiped with a solvent
such as benzine, thinner, etc.
t.y
Before using chemical wipes,
and observe the instructions.
and other parts.
Do not spray
•
Sound
volume.
Set the
volume
at a suitable
level
insect repellent
allow long-term
to avoid
environment.
operation
•
Lens
cameras, eyeglasses,
not to scratch
the
objects.
etc.). Be careful
lens with hard
such
as
on the cabinet. Also, do not
close contact with rubber or
panel.
When
excessively
soiled,
dilute a neutral detergent
in water, wet and
wring out the cloth and afterward wipe with a
care
Use commercially
available
lens
tissue to clean the lens (used to clean
substances
vinyl products because this could result in
discoloration,
peeling paint, etc.
Use a soft cloth to clean the cabinet
and
bothering other people. It is also better to keep
the volume level low and close the windows at
night to protect the neighborhood
volatile
be sure to read
dry cloth. Do not apply
directly to the projector.
®
•
Extended
When
period,
prevent
using
undiluted
detergent
usage.
this projector
stop periodically
eye fatigue.
for an extended
to rest the
eyes
to
the
Checking the package Contents
Make sure all of the following
items are included
dealer..---
in the package.
If anything
is missing,
please
contact
your
._,
_U
_Lz
C P-X960WA/970W
_Z2uT,2_'='_
-Remote control
Projector unit
Remote control
Batteries
_:_:_'
il
&_"_2_'*__
User's Guide (this document)
Power Cord
110V-US
220*UK, Europe
3_Conductor
video/Audio cable
RG B cable
(t5-15 pin M/M)
Names and functions
Mac adapter
with dip switch
of each part
Main unit
FOCUS button
Used to adjust the focus of the image on the
screen. (Refer to page 13.)
ZOOM button
Used to adjust the size of the
image. (Refer to page 13.)
INPUT button
Press this button to switch the input. The input
changes in the following sequence each time
this button is pressed.
MUTE
button
This button turns the sound
off. Press once to turn the sound off;
then press again to turn the sound
back on.
STANDBY
/ ON
Mouse cable x 3
RGB1 _
RGB2 _
VIDEO
MENU button
Displays the image menu. Refer to page 17 21 for details.
button
Press this button to turn the power on
and off. When turned off, the projector
enters standby status. Refer to page 13
- 14 for details.
Used to reset the initial settings.
Refer to page 10.17.25.26 for details.
LAMP indicator
Lights or flashes when the temperature
inside the projector increases or the lamp
does not light. Refer to page 33 for details.
TEMP indicator
Blinks when the fan malfunctions. Refer to
page 33 for details.
POWER indicator
This indicatorlights or blinks during standby
and during operation. Refer to page 33 for
details.
Speaker
Speaker
Remote control I/R receiver
Cooling fan
(exhaust side)
Cardng handle
Lens cap
Cooling fan
(intake side)
• Use the remote
control in front of the remote
control photoreceptor
at a distance
of about 5 m or less and an angle of 30 degrees to the left or fight of the center.
8
Names and functions of each part (continued)
/
Remote control I/R receiver
Main power switch
Used to turn the power on and off,
© : OFF
I:ON
AC IN jack
/
Used to connect the
accessory power cord.
I/fxCautionl
Connecting
Make sure the accesory
VIDEO
to the AC IN jack
power cord is plugged
into
the AC IN jack as far as it will go. Incomplete
connection can result in fire or electrical shock.
1
IN
jack
S-VIDEO iN jack
Mini DIN 4-pin connector
VIDEO IN jack
RCA jack
AUDIO L/R IN jack
RCA jack
RGB
IN
2
RGB IN jack
D-sub 15-pin shrink (1/2)
CONTROL
VIDEO
IN
AUDIO
IN
RGB OUT
CONTROL
jack_
D-sub 15-pin shrink
[]
7
USB jack
AUDIO IN jack (RGB)
Stereo mini jack
72e n_eOuse CtUr
orS_rbya _obenecoc
t tinrOlgledo
by
persona[ computer.
%
RGB OUT jack
D-sub 15-pin shrink
AUDIO OUT jack (RGBNIDEO)
Stereo mini jack
9
Names and functions of each part (continued)
Remote control transmitter
Press to switch the input. (Refer to page 13, 19.)
VIDEO, RGB button _
STANDBY
/ ON button
_
_
VEOEO
Turns the laser beam on and off. Refer to page
LASER
button
11
conceming
usage and observe the cautions.
sTAN_B¥/oN_
PosmoN
Used to turn the power on and off.
Press for 1 sec. or more to turn the power off
(enter standby status).
(Refer to pages13 and 14.)
* POSITION button
PressPosition,thenusethe mouse DiskPadto adjust
_
the image position (RGB mode only).
(Refer to page 16.)
_¢
$ DISK PAD / MOUSE
button
*4
(1) Used to select menu items when the menu
screen is displayed (refer to page 18 - 18).
(2) When the menu is not displayed, the mouse
shift function and left click function are active.
*t (3)After
the POSITION
button
has been
pressed, the screen can be moved upward,
downward and
ght.
*t
RESET
/ MOUSE
RIGHT
button
(1)Operates as the RESET batten when the menu
is displayed. Press this button to return to the
initial settings,
(2)Used to click the right mouse button when the
menu is not displayed (refer to page 25,26).
(3)Pressing this button after scrolling the screen
with POSITION returns the screen to the original
button
* MENU button
Used to turn the menu screen display on and off.
(Refer to page 17 - 21.)
Used to turn the freeze (still) image display on and off.
(Refer to page 15.)
VOLUME
¢ MAGNIFY
button
Used to magnify the displayed=msge.
(Refer to page 16.)
button
Adjusts the volume of the sound. Press [/\]
to
increase the volume and (V) to decrease the volume.
When there is no video signal input, operation is not
possible when the input video signal is outside the
sync range,
* P in P button "2
Used to turnP in P (Picture In Picture: displays sub video
signal images in the RG8 signal) on and off.
Each time this button is pressed, operation will change in
the following sequence:
button
Applies Mute. (Press the Play button again to
cancel.)
(1)
TIMER button
(1)- (3)
t
(Refer to page 20.)
Turns the display of the time set with the Timer
on the Menu screen on and off.
The timer is not displayed when no input signal
is detected or when SYNC is out of range or
during blanking or during freezing.
Refer to page 21 concerning the method used to
set the timer.
BLANK button
Used to turn blanking on and off.
(Refer to page 20.)
FOCUS button
Used to adjust the focus of the image on the
screen. (Refer to page 13.)
ZOOM button
Used to adjust the size of the image. (Refer to
page 13.)
* AUTO button
Used to execute auto-adjust.*3
*These
functions
do not operate when initial screen
message "NO INPUT
*1 POSITION
icon
When the POSITION button is pressed, the moving display icon
will appear at the bottom right of the screen.
While displaying the icon, you can operate POSITION.
IS DETECTED"
or "SYNC IS OUT OF RANGE" is displayed.
*3 Auto adjustment
function
The projector automatically adjusts 4 items (V. POSIT, H. POSIT,
H. PHASE, H. SIZE).
When you choose AUTO (move the cursor to the right from the
manual operation position), the AUTO confirmation menu shown
below is indicated.
*4 Disk Pad method of operation
• Move and select by tilting Disk Pad in the required direction.
• Press Disk Pad in to realize the function of the mouse left
button.
• A mouse cable is necessary if a mouse is to be used.
(Refer to pages 26, 27.)
"2 p in P function
With the P in P function,
signals are input to both RGB and
VIDEO. This function operates only when the RGB signal has
been selected. There is no display in the case of the no signal and
when the RGB signal is outside the sync range.
When P in P is used, audio is automatically switched to video.
In P in P, audio input can be switched by pressing the VOL /\and
VOL _/keys of the remote control, displaying the audio bar and
moving DiSK PAD left and right during the display.
E_ _
10
RGB/VIDEO
Names and functions of each part (continued)
•
•
•
•
•
•
•
•
•
•
/
Auto adjust can take up to 30 seconds.
Auto adjust may not operate correctly in some cases, depending
on the computer connected
and the signal.
Be sure to expand images to full screen size when displaying
low resolution
images.
After auto adjust, the image may be slightly dark in some cases due to automatic adjustment
of the signal level.
Auto adjust can not execute when the initial display is "NO INPUT IS DETECTED"
or "SYNC IS OUT OF RANGE"
during FREEZE or MAGNIFY.
Auto Adjust is executed when the following operations
are performed.
I. When the type of input source signal is changed.
2. When the Auto Adjust (AUTO) button is pressed.
The message AUTO IN PROGRESS
will be displayed on the screen during automatic adjustment.
The screen may be disrupted during automatic adjustment
but this is not a malfunction.
RGB 1 or RGB2 only can be used as the input signal.
Auto Adjust can also be executed using the operation buttons of the main unit. Hold down the RESET button and press
the input switch (INPUT) button.
r-
Loading the batteries
[_Remove
the
Loading
AA batteries
battery
cover.
Push
lifting
cover.
the
up
knob
the
while
battery
into the remote
control.
[_Loading
[_Close
I/_Caution]
Battery
usage cautions
Use only the specified batteries with this projector.
Also, do
not mix new and old batteries.
This could cause in battery
cracking or leakage,
which could result in fire or personal
injury.
When loading the batteries,
make sure the plus and minus
poles are correctly
oriented
as indicated
in the projector.
incorrect orientation
could cause battery cracking or leakage,
which could result in personal
injury or pollution
of the
surrounding
environment.
the batteries.
Make sure the plus and
minus poles are correctly
oriented.
(Caution}
the battery cover.
Remote control usage cautions
Do not drop the remote control or apply impact.
Do not wet the remote control or place it on any wet object.
Such actions could result in malfunction.
When not to be used for an extended
batteries from the remote control.
period,
Replace
becomes
control
the batteries
difficult.
when
remote
remove
the
operation
Do not place the remote control close to the cooling fan of
the projector.
Do not disassemble
the remote
control
in case
of
malfunction,
please
bring
it to the service
station.
CAUTION
LASER RADIATION
IS
EMITTED FROM THIS
APERTURE
11
Installation
Typical LCD Projector and Screen Installation
Use the diagram
below as reference
to determine
-"
To_D view
Screen
)
the screen size and projection
distnace.
S
_)
Side view
\_
_h
)
)
/
a (inches)
Screen size (inches)
b (inches)
Minimum
Maximum
4O
55
73
1
6O
85
114
2
8O
114
151
2
100
144
191
3
120
176
231
3
a. Distance
b.Distance
from the LCD projector to the screen
from the lens center to the bottom of
the screen (a,b : +/-10%).
150
220
282
4
200
291
386
6
(Caution)
The LCD projector
should normally
level (the legs can point upward).
be used
Positioning
the projector
sideways, or with the
lens pointing upward or downward can cause the
internal temperature
a malfunction.
to rise, which could result in
The projection distances shown in the diagram
the left are for full size (1,024 x 768 dots).
Using the adjusters ]
Use the adjusters
on the bottom to adjust the projection
f
(
angle.
Side view
,
Front
view
J
)
__
\
\\
Adjuster
Variable within the range of approximately
0° - 9 °
1. Lift up the projector and release the adjuster lock.
2. After adjusting the projection angle, firmly lock the adjusters.
3. Rotate the adjusters
IAkCaution]
for fine adjustment.
• Do not release
overturn
the locks
unless
the projector
is being
held;
or the fingers could get caught and cause personal
• Do not force the adjusters
otherwise,
the projector
could
injury.
to rotate. This could damage the adjusters
or cause the lock to fail.
• Lock the adjusters firmly. If the lock is difficult to operate, change the angle slightly and try again.
12
to
Basic operations
To project 1
m
5 7 4 2
5_
j4
1
_
1
Turn on the main power switch of the projector [ I: ON].
• The Power indicator
lights orange.
Press the STANDBY / ON button.
• The Power indicator will blink green and then light green.
• The green blinking indicates wannup.
3
Remove
4
Use the ZOOM button to adjust the screen size.
5
Use the FOCUS button to adjust the focus.
the lens cap.
( 1) The display shown to the right will appear when the FOCUS button is pressed.
(2) Use the FOCUS button to adjust the focus until the image is sharp.
+ + + FOCUS+ + +
(3) The message "Focus" will disappear if any other button is pressed.
• (When there is no input signal, the Focus characters are not displayed when the input signal is outside the sync range.)
6
7
Turn on the power to the connected equipment.
Refer to page 31 concerning
the connection
of other equipment.
Press
either
the INPUT
button
of the
projector or the VIDEO/RGB
button of the
remote control to select the signal to be
projected on the screen.
Exampleon-screendisplay
RGB 1
The selected signal input channel will be displayed in the lower right part of the screen.
13
Basic operations
(continued)
Turning off the power]
1
2
P _n P
MUTE
BLANK
1
Press the STANDBY/ON
button for approximately
• The Power indicator will blink orange, then the lamp wilt turn off. Approximately
indicator wilt light orange.
• After the power is turned off, the lamp will be cooled for approximately
be turned off even by pressing the STANDBY/ON
button.
• The standby
status wilt not be entered
if the time which
AUTO
TIMER
1 sec.
1 sec. after that, the
1 min. and the power cannot
the STANDBY/ON
button
is pressed
is too
short.
2
3
Turn off the main power switch of the projector [ _ : OFF].
Attach the lens cap.
(Caution)
The fan will continue nmning for approximately
1 min. after the STANDBY/ON
button is pressed.
Do not turn offthe main power switch while the lamp is on because this will shorten the service life of
the lamp.
Plug & Play
This projector
is VESA
DDC
1/2B compatible.
Plug & play is possible
VESA DDC (Display Data Channel) compatible.
(Plug & play is a system configured
with peripheral
operating
equipment
by connecting
including
a computer
to a computer
that is
and display,
and an
system.
_Caution_
• Use the RGB cable included with this projector when using plug & play. With other cables,
pins (12) - (15) are sometimes not connected (effective only for RGB1).
• This device is recognized as a plug-and-play
monitor. Use the standard Windows95/98
display
drivers.
• This function may not operate, depending on the personal computer used.
• When the DDC function does not operate on a personal computer running Windows95/98,
select the display type from Screen Priority. It is recommended
that Super VGA 1024 x 768
(60-75Hz)
be selected as the display type.
The DDC function will not operate when connected to a Macintosh.
14
Basic operations (continued)
/
[Freeze function]
This function is used to freeze the image being displayed.
(refer to page 10)
p _nP
MUTE
C)
@
BkANK
AOTO
TIMER
C)(2)C)
1
Press the FREEZE button.
• The image being displayed
• The [ || ] mark appears
will freeze.
in the lower fight corner of the screen when the Freeze function
Cancelling the FREEZE function
1
is on.
I
Press the FREEZE button.
• The FREEZE
function
will be cancelled.
• The [ _ ] mark will be displayed
(Caution)
• When
for approximately
there is no input signal, the Freeze
3 sec. when the FREEZE
function
is not effective
function
when
is cancelled.
the input signal is
outside the sync range.
• Pressing
the FREEZE button alternately
• The FREEZE
function
will be cancelled
turns the freeze function
on and off.
when the input select button is pressed
or the display
mode of the PC being used for display is changed.
• When a still image signal is input when the FREEZE
cancel the FREEZE function.
• FREEZE
function
will be cancelled
"P in P", "AUTO", "BLANK",
function
after the operations
"VOLUME
_, _/","MENU",
is on, make sure not to forget to
such as "FOCUS +,-",
"TIMER",
"MUTE" and "POSITION".
15
Basic operations (continued)
I Magnify function
Part of an image can be displayed
(refer to page 10)
m4
magnified.
S_
5
j6
p _n p
BL_NK
1
MUTE
AUTO
TIMER
Press the MAGNIFY + button.
• The center part of the image wilt be displayed
magnified
Changing the magnification
approximately
2x.
ratio ]
Press the MAGNIFY + button.
• When this button is pressed, the image wilt be displayed
3
Press the MAGNIFY-
even larger.
button.
• When this button is pressed, the image wilt be displayed
even smaller.
Moving the display area
4
Press the POSITION
5
Press the DISK PAD up, down, left and right buttons.
• The magnified
button.
area will move in accordance
with the button pressed.
Returning to normal display]
6
Press the MAGNIFY OFF button.
_Caution_
• When there is no video signal input, Magnify
is not effective
when the video signal input is
outside the sync range.
• The magnify
function
will be cancelled
when the input select button is pressed
or the display
mode of the PC being used for display is changed.
• The Magnify
16
function will be cancelled
after the operations
such as "AUTO",
"KEYSTONE".
Adjustments
and functions
1,2,3
\3
1
1
Press the MENU ( _)_)(_(_
) buttons of the projector or the
MENU button of the remote control.
• The Menu screen wilt appear. (refer to page 18 - 21 for details.)
2
Press the MENU ((i)_)_)(_))
buttons of the projector or the DISK
PAD button of the remote control to select the menu item to be
adjusted.
3
• The selected
menu item will be displayed
in orange.
Adjust the selected menu item with the MENU ((i)(_)_i)_))
buttons of the projector or the DISK PAD button of the
remote control.
• The selected menu item wilt be displayed
in orange.
Returning to the initial settings I
• Select the adjustment
item to be returned
to the initial settings.
• Press the RESET button.
17
Adjustments and functions
(continued)
SET UP
Images
and display positions
can be adjusted
from the SETUP menu.
RGB signal input
[
ETUP
INPUT
VOLUME
Video signal input
/__
_
E_
BRtGHT
_
_
CONTRAST
_
V POSIT
H
100
POSIT
H PHASE
H SIZE
COLOR
800
BALE
Adjustment item
Adjustment description
VOLUME
Volume decreases
BRIGHT
(BRIGHTNESS)
_
Volume increases
Darker _
CONTRAST
Brighter
Lower contrast _
SHARPNESS
Stronger contrast
Softer image _
COLOR
Sharper image
Less _
TINT
More
Redder _
Greener
V, POSIT
(V. POSITION)
Moves the image up and down.
H. POSIT
(H. POSITION)
Moves the image left and right.
H, PHASE
Eliminates blanking.
H, SIZE
Adjusts the horizontal size of the image.
COLOR BAL R
(COLORBALANCERed)
Less
COLOR BAL B
(COLORBALANCEBlue
Less
red _
More
blue _
red
More blue
Using the SETUP Menu
Move the cursor to the item to be adjusted and move the MENU
button of the remote control to change the length of the bar display.
(Caution)
• The menu cannot
out of range.")
be displayed
button
while the initial screen
of the projector
("No input is detected."
• Tint, color and sharpness
with N-PAL, M-PAL, PAL or SECAM
cannot
be adjusted
video signal input.
with RGB signal input.
• V. POSIT, H. POSIT, H. PHASE and H. SIZE cannot be adjusted
• Displaying
18
or "Sync
is being displayed.
• Tint cannot be adjusted
• FREEZE
or the DISK
function
wilt be cancelled
after the operation
the menu cancels freeze operations.
"Menu".
with video signal input.
PAD
is
Adjustments and functions
(continued)
/
INPUT]
The INPUT menu is used to select RGB signal sync signal frequency
of the monitor
VIDEO
•
_
J
RGB
VIDEO _.
fH:38kHz
fV:60Hz
Adjustment
signal.
tMAG E
IMAG E
RGB
and the VIDEO
item
Adjustment
t, AUTO
NTSC
PAL
SECAM
NTSC4 43
M_PAL
N-PAL
description
RGB
Displays the following RGB inputs
fH: horizontal sync frequency
fV: vertical sync frequency
VIDEO
Sets the video signal system, When the screen is unstable (no color)
or rolls, select the mode that matches the input signal,
19
Adjustments and functions
(continued)
IMAGE
Projection
image inversion,
etc., can be selected
from the IMAGE
SETUP
INPUT
IMAGE
menu.
OPT
SETUP
INPUT
KEYSTONE
STARTUP
_M_,GE
OPT
_
•
_E5
SETUP
_P_ IN FL
INPUT
IMAGE
OPT
[S E T U P ] IN P U T
b
EL1
KEYSTONE
BLANK
}
_
•
MIRROR_
SETUP
iNPUT
iMAGE
OPT
E
Adjustment
item
KEYSTONE
MIRROR
BLANK
START UP
P in P
2O
Adjustment
description
Reduces keystone
distortion at the bottom _
Reduces keystone
distortion at the top
Sets vertical or horizontal inversion of the projected image.
H: horizontal inversion only
V: vertical inversion only
H&V: both horizontal and vertical inversion.
Sets the color to be used for blanking with BLANK ON or when there is no signal.
Blanking is turned on, when there is no signal for approximately 5 min.
Opens and closes the initial settings screen during signal input at start up.
When canceled, the background color will change to blue.
Selects the P in P sub screen display position.
/_
Adjustments and functions
(continued)
/
OPT
Communication
functions,
etc., can be set from the OPT menu.
OM BITS
TIMER
[SETUP[
_NPUT
COMSPEED
COMBITS
TIMER
LANGUAGE
AUTO
OFF
SYNC
ON G
•
LANGUAGE
COMSPEED
SYNC ON G
SETUP
INPUT
IMAGE
bOR_
•
[ S E T U P ] IN P U T [ [ M A G E
COMSPEED
C_COM_TS
_MER
_TIMER
LANGUAGE
Adjustment
item
COM. SPEED
COM. BITS
TIMER
Adjustment
Sets the communication
description
speed (5 steps).
Sets the bit configuration for the communication
7N1...7 data bits, No parity, 1 stop bit.
8N1...8 data bits, No parity, 1 stop bit.
data.
Sets the timer display time (0 - 99) min.
LANGUAGE
Selects the menu screen language
(English, French, German, Spanish, Italian, Norwegian, Dutch, Japanese).
AUTO OFF
Sets the time after which the power will be turned off (standby status) when
there is no input signal. The settings are 1 - 99 min, 0 and None.
SYNC ON G
Sets the SYNC ON G feature on/off.
21
Connection to the video signal terminals
1. Input signals
Brightness signal
Color signal
S-VIDEO signal
1.0V p-p, 75 £2terminator
0.286V p-p (burst signal), 75 £2 terminator
1.0V p-p, 75 £2terminator
VIDEO signal
Input
200mV rms, 20k £2or less (max. 3.0V p-p)
Output
0-200mVrms,
Audio signal
1k
2. Signal input jacks
Brightness signal
Color signal
Ground
Ground
S-VIDEO input (mini DIN 4-pin)
_Caution_
The priority sequence
of the video input jacks is as follows.
(1) S-VIDEO input jack
(2) RCA jack input jack
When video signals are being projected, the audio input by the video is output to the audio
output jack (RGB/V1DEO).
Connection to the RGB signal terminal
1. Input signals
Video signal
Analog, 0.7V p-p, 75 £2terminator (positive polarity)
Horizontal sync signal
TTL level (positive/negative
polarity)
Vertical sync signal
TTL level (positive/negative
polarity)
Compound sync signal
TTL level
Input
200mV rms, 20k £2or less (max. 3.0V p-p)
Output
O~200mVrms, 1k £2
Audio signal
2. Signal input jacks
22
1
Video input (red)
9
N.C
2
Video input (green)
10
Ground
3
Video input (blue)
11
N.C
4
N.C
12
DDC jack (Display Data Channel)
5
N.C
13
Horizontal sync signal/compound
6
Ground (red)
14
Vertical sync signal
7
Ground (green)
15
DDC jack (Display Data Channel)
8
Ground (blue)
5
1
15
11
,0(OoOoO
o&
sync signal
D-sub 15-pin
shrink jack
Connectiontothe RGBsignalterminal(continued)
3. Example
of computer
signal
Resolution
Hx V
fH
(kHz)
fV
(Hz)
640 x 400
24.8
56,4
640 x 350
37.9
85,1
640 x 400
37.9
720 x 400
Rating
Signal mode
Display mode
NEC PC9800
Zoom in
VESA
VGA-1
Zoom in
85.1
VESA
VGA-2
Zoom in
37.9
85.0
VESA
TEXT
Zoom in
640 x 480
31,5
59.9
VESA
VGA-3
Zoom in
640 x 480
35,0
66.7
Mac13"mode
Zoom in
640 x 480
37,9
72.8
VESA
VGA-3(72Hz)
Zoom in
640 x 480
37,5
75.0
VESA
VGA-3(75Hz)
Zoom in
640 x 480
43,3
85.0
VESA
VGA-3(85Hz)
Zoom in
800 x 600
35,2
56.3
VESA
SVGA(56Hz)
Zoom in
800 x 600
37,9
60.3
VESA
SVGA(6OHz)
Zoom in
800 x 600
48,1
72.2
VESA
SVGA(72Hz)
Zoom in
800 x 600
46,9
75.0
VESA
SVGA(75Hz)
Zoom in
800 x 600
53,7
85.1
VESA
SVGA(85Hz)
Zoom in
832 x 624
49,7
74.5
Mac16"mode
Zoom in
1024 x 768
48,4
60.0
VESA
XGA(6OHz)
1024 x 768
56,5
70.1
VESA
XGA(7OHz)
1024 x 768
60,0
75.0
VESA
XGA(75Hz)
1152 x 864
67,5
75.0
VESA
SXGA(75Hz)
Zoom out
1280 x 960
60,0
60.0
VESA
SXGA(6OHz)
Zoom out
1280 x 1024
64,0
60.0
VESA
SXGA(60Hz)
Zoom out
1280 x 1024
80,0
75.0
VESA
SXGA(75Hz)
Zoom out
/
Note 1
SW 1 ON
SW 2 ON
SW 2 ON
SW 4 ON
UUUUU
Note 1: Mac adapter is necessary to the resolution
Projector is compatible with 13 inch mode
Mac 13" mode switch 1 and switch 2 are
Mac 16" mode switch 2 and switch 4 are
mode.
and 16 inch mode.
ON.
ON.
(Example 16 inch mode)
(Caution)
• Some computers may have multiple
not be possible with this projector.
• Be sure to check jack
projector to a computer.
• Depending
type,
signal
display screen modes.
level,
timing
Use of some of these modes will
and resolution
on the input signal, full-size display may not be possible
before
connecting
this
in some cases.
23
Connectiontothe RGBsignalterminal(continued)
4. Initial set signals
The following signals are used for the initial settings.
The signal timing of some computer models may be different.
the V_POS1T and H.POS1T of the menu.
In such case, refer to pages 17 and 18 and adjust
Back porch b
:_'-!
DATA
_ ,I
!
HSYNC _C_
Computer/Signal
Front porch d
i
Display interval c
1i
1i
Synca
Horizontal signal timing (ps)
Computer/Signal
a
b
c
d
VGA-1(85Hz)
2.0
3.0
20.3
1.0
SVGA (72Hz)
VGA-2(85Hz)
2.0
3.0
20.3
1.0
SVGA (75Hz)
PC-9800
3.0
3.8
30.4
3.0
TEXT
2.0
3.0
20.3
1.0
Horizontal signal timing (ps)
a
b
c
d
2.4
1.3
16.0
1.1
1.6
3.2
16.2
0.3
SVGA (85Hz)
1.1
2.7
14.2
0.6
Mac 16"mode
1.1
3.9
14.5
0.6
2.5
15.8
0.4
VGA-3
3.8
1.9
25.4
0.6
XGA (60Hz)
2.1
Mac 13"mode
2.1
3.2
21.2
2.1
XGA (70Hz)
1.8
1.9
13.7
0.3
VGA-3(72Hz)
1.3
3.8
20.3
1.0
XGA (75Hz)
1.2
2.2
13.0
0.2
VGA-3(75Hz)
2.0
3.8
20.3
0.5
SXGA(1152X964,75Hz)
1.2
2.4
10.7
0.6
VGA-3(85Hz)
1.6
2.2
17.8
1.6
SXGA(1286X960,60Hz)
1.0
2.9
11.9
0.9
SVGA(56Hz)
2.0
3.6
22.2
0.7
SXGA
(1280
X 1024,
60Hz)
1.0
2.9
11.9
0.9
SVGA(60Hz)
3.2
2.2
20.0
1.0
SXGA
(1280
X 1024,
75Hz)
1.1
1.8
9.5
0.1
Front )orch d
Back porch b
i
i-1
DATA
_
]_
VGA-1 (85Hz)
24
"]'Hi
1i
1
VSYNC
Computer/Signal
Display intervalc
i
Sync a
Vertical signal timimg (lines)
a
b
c
d
3
60
350
32
Vertical signal timimg
Computer/Signal
(lines)
a
b
c
d
SVGA (72Hz)
6
23
600
37
3
21
600
1
VGA-2 (85Hz)
3
41
400
1
SVGA (75Hz)
PC-9800
8
25
400
7
SVGA (85Hz)
3
27
600
1
3
39
624
1
TEXT
3
42
480
1
Mac 16"mode
VGA-3
2
33
480
10
XGA (60Hz)
6
29
768
3
29
768
3
Mac 13"mode
3
39
480
3
XGA (70Hz)
6
VGA-3 (72Hz)
3
28
480
9
XGA (75Hz)
3
28
768
1
32
864
1
VGA-3 (75Hz)
3
16
480
1
SXGA(1152X964,75Hz)
3
VGA-3 (85Hz)
3
25
480
1
SXGA(1280X960,6OHz)
3
36
960
1
38
1024
1
38
1024
1
SVGA (56Hz)
2
22
600
1
SXGA
(1280
X 1024,
60Hz)
3
SVGA (60Hz)
4
23
600
1
SXGA
(1280
X 1024,
75Hz)
3
Connecting the USB
1. Connect
the projector
and computer
with a suitable
cable from the projector.
2. Press the INPUT button of the projector
where the computer is to be connected.
3. Start the mouse function.
4. Refer to page 10 concerning
commercially
available
1/2 button
of the remote
or the RGB
cable.
Disconnect
control
the mouse
/
and select the input
the remote control of mouse operations.
5. Varying the force with which the DISK PAD button is pressed varies the speed of mouse operation.
USB jack
(B type)
2
1
Projector
Computer
+5V(_l_
USB jack
(A type)
@+5V
[email protected]
@-DATA
[email protected]
@+DATA
1
3
4
[email protected]
2
3
4
@GND
USB cable
_Caution-_
• Before making connections, read the instruction
• Use the optional USB cable to connect.
manual
of the equipment
to be connected.
• Effective with USB only when the mouse is used.
• Do not use with any device other than a personal computer.
• When using with Windows 95, it is necessary to set so that USB can be used with version
OSR 2.1 or higher. Depending on the kind or the virsion of the host controller, operation may
not be possible in some cases.
• In the case of notebook type computers
some cases the built-in pointing
the mouse may not be selected.
with a built-in pointing
device such as a track ball, in
device wilt have priority even if a mouse is connected
In such case, disable the built-in pointing
so that an external mouse can be selected.
device and change the BIOS setting (system
and
setup)
After changing the B1OS setting, perform the operations described in 1 - 3 above.
Refer to the computer hardware manual concerning the BIOS setting.
Also, some computers
may not have a utility
computer hardware manual.
program
to operate
a mouse.
Refer
to the
25
Connection to the control signal terminal
1.
Mouse
functions
(1) Turn off the main power switches
provided
projector.
or an optional
suitable
of the projector
commercially
and computer
available
and connect
cable.
the two units with the cable
Disconnect
the USB cable
from the
(2) Turn on the main switch of the projector (the POWER indicator lamp will light green).
(3) Press the 1NPUT button of the projector or the RGB button of the remote control and select the input
where the computer is to be connected.
(4) Turn on the computer power supply.
(5) Start the mouse function.
If the mouse has not been started, reboot the computer
(soft reboot or reboot buttons).
(6) Refer to page 10 concerning remote control operation.
(7) Varying the force with which the DISK PAD button is pressed
PSI2 Mouse
Projector
Corn _uter
Mouse jack Mini
DIN 6-pin
CLK
DATA
control jack
D-sub 15-pin shrink jack
1
varies the speed of mouse operation.
5
0IoOOOOoO
L
SEL0
RTS
11
+5V
GND
15
Use the mouse cable provided
Cables for ADB
(Caution-)
or a PS/2 mouse cable (for IBM and compatibles).
mouse (Apple),
bus mouse (NEC) and serial mouse are available
as options.
• Before making connections, read the instruction manual of the equipment
• Turn off the projector and computer power supplies before connecting.
to be connected.
Connecting the mouse cable with the computer power on can result in a malfunction.
Use the mouse cable provided or an optional mouse cable to make the connection.
• In the case of notebook type computers with a built-in pointing device such as a track ball, in
some cases the built-in pointing device wilt have priority even if a mouse is connected and
the mouse may not be selected.
In such case, disable the built-in pointing
so that an external mouse can be selected.
device and change
After changing
the operations
the B1OS setting, perform
the B1OS setting (system
described
in (1) - (3) above.
Refer to the computer hardware manual concerning the BIOS setting.
Also, some computers
may not have a utility program to operate
computer
26
hardware
manual.
setup)
a mouse.
Refer
to the
Connection
tothecontrolsignalterminal(continued)
CONTROL
signal jack
RS-232C
PS/2
ADB
Serial
Projector
1
2
CLK
3
DATA
|
ADB (Mac) mouse
Mouse
Pin no.
Computer
Mouse
jack
Mini DIN 4-pin
II
(POWER ON)
ADB
DATA
DATA
4
5
6
SELO
SELO
SELO
7
RTS
RTS
RTS
+5V
+5V
GND
GND
RTS
RTS
8
GND
9
10
GND
GND
11
Mouse cable (ADB) (option)
12
13
RD
14
TD
TD
15
Serial mouse
Pro
_ctor
Computer
Mouse jack
D-sub 9-pin
RD
TD
DTR
GND
SELO
RTS
_DSR
t
_CTS
[email protected]®®®
®_®®
\
_RTS
GND
TD
Mouse cable (serial) (option)
27
Connection
tothecontrolsignalterminal(continued)
2.
RS232C
communication
(1) Turn off the projector
and computer
power supplies and connect
with the RS232C cable.
(2) Turn on the computer power supply and, after the computer has started up, mm on the projector power supply.
(3) Refer to page 21 and set the communication
speed and the number of communication
bits.
(4) Start RS232C
communication.
Projector
Computer
RS232C jack
D-sub 9-pin
RD
TD
DTR
GND
Control jack
D-sub 15-pin shrink
1
5
SELO
_)DSR
RTS
RTS
DTS
6_10
11
®®®®
15
GND
RS232C cable
RD
TD
Pr_ector-_computer
Response code
Command
28
1st
2nd
Computer4projector
Inqui_ code
Setting code
da_
1st
2nd
1st
2rid
data
DeNults_ting cede
1st 2nd
MOUSE
11h 05h
+1
20h
05h
31h
05h
+1
40h
05h
COMMUNICATE
11h 06h
+1
20h
06h
31h
06h
+1
40h
06h
POWER
11h
11h
+1
20h
11h
31h
11h
+1
ZOOM
11h
12h
+1
31h
12h
+1
FOCUS
11h
13h
+1
31h
13h
+1
MIRROR
11h
14h
+1
20h
14h
31h
14h
+1
40h
14h
INPUT
11h 21h
+1
20h
21h
31h
21h
+1
40h
21h
(VIDEO)SYSTEM
12h 22h
+2
20h
22h
32h
22h
+2
40h
22h
VOLUME
11h 23h
+1
20h
23h
31h
23h
+1
40h
23h
MUTE
11h 24h
+1
20h
24h
31h
24h
+1
40h
24h
BRIGHT
13h
31h
+3
20h
31h
33h
31h
+3
40h
31h
CONTRAST
13h
32h
+3
20h
32h
33h
32h
+3
40h
32h
COLOR
13h
33h
+3
20h
33h
33h
33h
+3
40h
33h
TINT
13h
34h
+3
20h
34h
33h
34h
+3
40h
34h
SHARPNESS
13h
35h
+3
20h
35h
33h
35h
+3
40h
35h
H.PHASE
13h
37h
+3
20h
37h
33h
37h
+3
40h
37h
H.POSIT
14h
38h
+4
34h
38h
+4
40h
38h
H.SlZE
14h
36h
+4
34h
36h
+4
40h
36h
V.POSIT
14h
3Ah
+4
34h
3Ah
+4
40h
3Ah
COLOR BALANCE R
13h
3Bh
+3
20h
3Bh
33h
3Bh
+3
40h
3Bh
COLOR BALANCE B
13h
3Dh
+3
20h
3Dh
33h
3Dh
+3
40h
3Dh
AUTO ADJUST
11h
3Ch
+1
20h
3Ch
31h
3Ch
+1
40h
3Ch
BLANK
11h 41h
+1
20h
41h
31h
41h
+1
40h
41h
MAGNIFY
11h
15h
+1
20h
15h
31h
15h
+1
40h
15h
FREEZE
11h
16h
+1
20h
16h
31h
16h
+1
40h
16h
Connection
tothecontrolsignalterminal(continued)
Command
data chart
Item
00h=disable
COMMUNICATE
0Xh=8N1,
mouse function, 01 - 7Fh=start mouse function
1Xh=7N1
X0h=1200bps,
X1h=2400bps,
X2h=4800bps,
X3h=9600bps,
X4h=19200bps
POWER
3Eh=power
ZOOM
01 - 3Fh=Zoom +, 41 - 7Fh=Zoom -
FOCUS
01 - 3Fh=Focus +, 41 - 7Fh=Focus -
MIRROR
00h=Normal,
01h=H : Invert, 02h=V : Invert, 03h=H & V : Invert
INPUT
1lh=VIDEO,
21h=RGB1, 22h=RGB2
SYSTEM(VIDEO)
00h
00h
off (standby status), 3Fh=power on
00h=Auto,
02h=PAL,
00h 01h=NTSC, 00h 04h=NTSC4.43
00h 03h=SECAM, 00h 05h=M-PAL, 00h
06h=N-PAL
VOLUME
00h (low volume) - 24h (high volume)
MUTE
00h=mute off,
BRIGHT
00h
00h
00h(dark)-00h
CONTRAST
00h
00h
00h(Iow)-00h
COLOR
00h
00h
00h(pale)-00h
TINT
00h
00h
00h(reddish)-00h
SHARPNESS
00h
00h
00h(soft)-00h
H.PHASE
00h
00h
00h-00h
H.POSIT
00h
00h
00h
00h
00h
00h
01h (Right) moves one step
7Fh (Left) moves one step
H.SIZE
00h
00h
00h
00h
00h
00h
01h(Large) moves two step
7Fh (Small) moves two step
V.POSIT
00h
00h
00h
00h
00h
00h
01h(Up) moves one step
7Fh (Down) moves one step
COLOR BALANCE R
00h
00h
00h (Light red) -00h
COLOR BALANCE B
00h
00h
00h (Light blue) - 00h
AUTO ADJUST
00h (AUTO ADJUST (Play))
BLANK
0Xh=blanking off, 1Xh=blanking on
X=8 Black, X=9 Blue, X=F White
MAGNIFY
00h=normal display, 01h=zoom Magnify display or Magnify ratio up.
7Fh=zoom ratio down
FREEZE
00h=normal
The command
/
Data code
MOUSE
code configuration
• The first byte of a command
with 4 bits on the LSB side.
01h=mute on
00h
00h
24h(strong)
00h
24h (dense)
00h
00h
00h
24h(bright)
24h(greenish)
24h (sharp)
24h
00h
24h (Dark red)
00h
24h (Dark blue)
display, 01h=still image display
consists
indicates
of a 2-byte command
the command
and the following
type with 3 bits on the MSB side and the data length
Projector - computer
'0xH' : Error code
Computer - projector
'2xH' : inquiry code
'lxH'
'70H'
'3xH'
'4xH'
: response code
: frame error code
data.
: setting code
: default setting code
'x' indicates the data length (example: x_ means a 2-byte command).
• The second byte of a command indicates the command contents.
29
Connection
tothecontrolsignalterminal(continued)
Requesting
projector status
(1) Send the request code '20H' + 'yyH'
(2) The projector
returns the response
Changing
the projector
settings
(1) Send the setting code '3xH' + 'yyH'
(2) The projector
(3) The projector
from the computer
code ' 1xH' + 'yyH'
to the projector.
+data to the computer.
+data from the computer
to the projector.
changes the setting based on the above setting code.
returns the response code ' 1xH' + 'yyH' +data to the computer.
( Caution ) The response
data in (3) above need not match the setting data in (1).
For example, when the projector cannot set the setting data in (1), the projector may set the/
closest value. That value will be used as the response data in (3). Or else the projector wilt]
return the error code '0xH' + 'yyH' +data.
Using the projector
default settigns
(1) The computer sends the default setting code '40H'
(2) The projector
(3) The projector
+ 'yyH'
to the projector.
changes the specified setting to the default value.
returns the default value with the response code ' 1xH' + 'yyH'
When a command
sent by the projector
cannot
be understood
-data.
by the computer
(1) The computer sends the command code '3xH',
'4xH' or '4xH' + 'yyH' +data to the projector.
(2) When the command
sent by the projector cannot be understood,
the error command
'0OH' + 'yyH'
returned
J
is
by the computer.
When data sent by the projector
(1) The computer sends the command
(2) When the command
returned.
cannot be understood
code '3xH', '4xH' or '4xH'
sent by the projector
cannot
be understood,
+ 'yyH'
+data to the projector.
the the error code '0xH'
+'yyH'
+data is
When the data length is greater than indicated by the data length code, the projector wilt ignore the excess data code.
Conversely, when the data length is shorter than indicated by the data length code, an error code will be
retumed
When
Repeats
to the projector.
a frame
error occurs
10 times per second until there is some sort of response
When the interval
between
bytes in one command
to the error code 70H + 70H.
is 500ms or greater
When a command or data is not sent within 500ms after the command code '2xH',
'3xH' or '4xH' is sent by
the computer, the error command '70H' +'70H'
will be returned as soon as the 500ms elapses. After this, if
there is no response
(Caution)
within 1 sec,
• Operation
• Provide
30
a frame error will occur.
cannot be guaranteed
when the projector
an interval of at least 40ms between
receives
the response
an undefined
command
code and any other code.
or data.
Example of system setup
Computer
(notebook type)
/
AC input
@
/
I
\
i
i
Computer
(desktop type)
i
i
Video tape recorder with S jack
i
i
Video tape recorder
Speaker (with built-in amp)
( Caution
Display monitor
Turn power off to all devices
Refer to the instruction
before connecting.
manual of each device before connecting.
Cleaning the Air filter
Clean the air filter about every 100 hours.
1
Turn off the MAIN POWER switch of the projector and
pull out the power cord.
2
Remove the front air filter.
Filter
Parts Number
Air Filter
MU00831
31
Cleaning the Air filter (continued)
3
Cleaning the air filter with a vacuum cleaner
4
Installing the air filter
(Caution)
When
the air filter
prevent
becomes
clogged
with dust, etc., the projector
the internal heat level rising. (The lamp indicator
Do not operate
the projector
with the air filter removed.
dust can enter the LCD panel and produce
an adverse
color changes
power
may turn off to 1
/
to red.)
(lf used with the air filter removed,/
/
effect on image quality.)
Lamp
The light source lamp has a service life.
When used for an extended time, the images may become
A malfunction
The following
darker and the colors may deteriorate.
could occur if the projector is used in this condition, so replace the lamp with a new one.
indicator or a message which appears when the power is turned on will indicate when the lamp
should be replaced.
At such time, it is necessary
to replace
the lamp with a new one. For lamp replacement,
please
contact
your
dealer or service company.
Even when the lamp is at a high temperature, the power to the projector may cut off to prevent
an excessive temperature increase inside the projector. (The POWER indicator turns off.) Turn
off the MA1N POWER switch, wait for some 20 minutes and turn on the MAIN POWER
(Caution_
switch
again.
If the projector
is not recovered
after turning
on the MA1N POWER
switch
please contact your dealer or service company.
Message
table
Screen displays
The following
messages
are displayed
on the screen.
CHANGE THE LAMP"CALL
The total lamp usage time is nearing the service life of the lamp. Replace with a new lamp.
A MAINTENANCE PERSON"
The lamp will turn off automatically when the lamp replacement time has been exceeded.
"CHANGE THE LAMP"
"CALL
A MAINTENANCE
The total lamp time is nearing the lamp replacement time. After (*) hours, the lamp will turn
off. Quickly replace with a new lamp.
PERSON"
'1
"1
*Indicates the number of hours until the lamp turns off automatically.
"THE POWER WILL
TURN OFF AFTER * hr."
Blinking of
"CHANGE THE LAMP"
approximately 10 min. and then turn off automatically. Replace with a new lamp.
NO INPUT IS DETECTED
There is no signal input (refer to pages 22, 23).
SYNC IS OUT OF RANGE
The current horizontal or vertical frequency cannot be used by this projector (refer to pages 23, 24).
• 1 This display will disappear
32
The total lamp time has exceeded the replacement time. The indicator will blink for
after 3min. but wilt reappear
when the power is turned on again.
Message table (continued)
Indicators
The POWER
indicator,
LAMP indicator
and TEMP indicator
light or blink in the following
/
cases.
POWER
indicator
LAMP
indicator
TEMP
indicator
Lights orange
Turns off
Turns off
Standby status
Flashes green
Turns off
Turns off
Warming up
Lights green
Turns off
Turns off
Operation status ,1
Flashes orange
Turns off
Turns off
Cool down
Lights red
Lights red
Turns off
The lamp does not light. *2 tuming the power on again. Clean the air
The interior is too hot.
filter before turning the power on. If the
indicatorstill lights, contact your dealer.
Lights red
Flashes red
Turns off
A lamp has not been inserted
or the lamp cover is missing. Contact your dealer.
Lights red
Turns off
Flashes red
The coolingfan is not operating. Contact your dealer.
Flashes red
Flashes red
Turns off
The total lamp time has
Contact your dealer.
exceededthe replacementtime.
Status
Processing
Wait some time (approx. 20 min.) before
When the LAMP or TEMP indicator lights or flashes, turn off the MAIN POWER switch before proceeding.
If the problem still persists, contact your
dealer or service company.
*1: When the cooling fan is stopped and the interior becomes overheated, the power will tam off automatically
off). In such cases, tam offthe
to allow cooling (the indicator will turn
projector power, allow the set to cool aM then turn the projector power on again. The lamp will then ligN. If the lamp
does not light, contact your dealer or service company.
*2: In some cases, when the air holes becomes blocked and the interior temperature rises, the lamp will be turned off for protection and the LAMP
iMicator will flash red. In such cases, turn offthe MAIN POWER switch, allow the set to cool (for approx. 20 min.) and then turn the power on again.
When you think something wrong
Before requesting repair, check in accordance
contact your dealer.
Symptom
with the following
chart. If the situation cannot be corrected,
Possible cause
Remedy
then
Page
The power is not
turned on.
,The main power switch is not turned on.
,The power cord is disconnected.
,Turn on the main power switch.
,Plug the powercord into an AC poweroutlet.
P.13
P.9
No video or audio.
,The input is not correctly set.
,Use the projector or remote control to set.
•No signal input.
,Connect correctly.
P.8.10,
13,19
P.9.31
,The projector is not correctly connected.
,The volume is set to minimum.
P.9.31
P.10.18
•Mute is turned on.
•Audio is switched to RGB when P in P is on.
,Connect correctly.
,Press VOLUME + on the remote control or display
the menu screen and adjust the volume.
,Press the MUTE button.
,Displaysthe Volumebarandswitchesthe Audioinput.
,The
,The
fully
•The
,Connect correctly.
,Select BRIGHT with the MENU button and then
press the (@) ) key.
,Remove the lens cap.
P.9.31
P.17
Video is present but
no audio.
Audio is present but
no video.
projector is not correctly connected.
brightness adjustment knob is rotated
clockwise,
lens cap is still on.
P.8.10
P.10
P.13
Colors are pale and
colormatching is poor.
Color density and color matching are not
correctly adjusted.
Adjust the video.
P.18
Images are dark.
,Brightnessandcontrastare not correctlyadjusted.
•The lamp is nearing the endof its servicelife.
,Adjust the video.
,Replace with a new lamp.
P.18
P.32
Video is blurred.
Focus or H PHASE is out of adjustment.
Adjust the focus or H PHASE.
P.13.18
The LAMP indicator
lights red.
Lamp failure.
Wait approximately 20 min. and then turn the
power on again.
P.33
Internal overheating.
,Make surethe ventilation openingsare not blocked.
•Clean the air filter.
•Lowerthe ambienttemperatureto 35degreesC or less.
P.31.32
A bright dot may
be seen in the picture.
This is a phenomenon
peculiar
to the liquid crystal
and is not a problem.
33
Specifi cations .These
speoi'_oations
are
sobject
tochange
without
no.ce.
Product name
Liquid crystal projector
Model
CP-X960WA/970W
Display method
Three liquid crystal panels, three primary color system.
Liquid crystal
Panel size
3.3 cm (1.3 type)
panel
Drive system
TFT active matrix
Number of pixels
786,432 pixels (1,024 horizontal x 768 vertical)
Lens
Zoom lens F=1.7~2.3
Lamp
190w UHB
Speaker
1.2W + 1.2W (Stereo)
Power supply
AC100 ~ 120V, 3.7A / AC220 - 240V, 1.5A.
Power consumption
320W
Operating temperature
range
f=49-64mm
0 - 35°C
Size
11" (W) x 5" (H) x 14" (D), 289mm(W) x 124mm(H) x 345mm(D)
Weight (mass)
13 Ibs, 5.9kg
S VIDEO: mini DIN 4-pin jack
VIDEO signal input jacks
VIDEO: RCA jack
AUDIO: RCA jack
RGB signal input/output jacks
RGB signals: D-sub 15-pin shrink jack
Audio: stereo mini-jack
CONTROL signal jack
D-sub 15-pin shrink jack
USB jack
B type
Dimensional
Unit: inches
34
Diagram 1
About the warranty and after-service
/
About the warranty]
A warranty
is provided
for this product.
Fill in the necessary
items and store in a safe place.
About after-service]
When a problem occurs, please check first using the Troubleshooting
If the problem still persists, contact your dealer or service company.
Chart provided
in this instruction
manual.
About repairs during the warranty period
Repairs will be made as described in the warranty.
For details, please read the warranty.
Repairs after the warranty period has elapsed ]
Paid repairs will be made if desired in the event that the function
Parts will be made available for a minimum period of 8 years.
can be restored
by such repairs.
35