bettini SP-1256HSP Instruction

Mini Speed Dome Camera
Mini
Internal
INSTRUCTION
MANUAL
External
CAUTl0N
RISK OF ELECTRIC
SHOCK DO NOT OPEN
CAUTION
：To reduce the risk of electrical shock, do not open covers.
No user serviceable parts inside.
Refer servicing to qualified service personal.
This lightning flash with arrowhead symbol is intended to alert the user to the
presence of un-insulated "dangerous voltage" within the product's enclosure that
may be of sufficient magnitude to constitute a risk of electric shock to persons.
This exclamation point symbol is intended to alert the user to the presence of
important operating and maintenance (servicing) instructions in the literature
accompanying the appliance.
WARNING：To prevent the risk of fire or electric shock hazard do not expose
this camera to rain or moisture.
Mini Speed Dome Camera Introduction Manual
1
▌▌Important Safeguard
1.
Read Instructions
Read all of the safety and operating instructions before using the product.
2.
Retain Instructions
Save these instructions for future reference.
3.
Attachments
／Accessories
Do not use attachments or accessories unless recommended by the appliance manufacturer as they
may cause hazards, damage product and void warranty.
4.
Water and Moisture
Do not use this product near water or moisture.
5.
Installation
Do not place or mount this product in or on an unstable or improperly supported location. Improperly
installed product may fall, causing serious injury to a child or adult, and damage to the product. Use
only with a mounting device recommended by the manufacturer, or sold with the product. To insure
proper mounting, follow the manufacturer’s instructions and use only mounting accessories
recommended by manufacturer.
6.
Power source
This product should be operated only from the type of power source indicated on the marking label.
▌▌Precautions
Operating
Before using, make sure power supply and others are properly connected.
While operating, if any abnormal condition or malfunction is observed, stop using the camera
immediately and then contact your local dealer.
Handling
Do not disassemble or tamper with parts inside the camera.
Do not drop or subject the camera to shock and vibration as this can damage camera.
Care must be taken when you clean the clear dome cover. Especially, scratch and dust will ruin your
quality of camera.
Installation and Storage
Do not install the camera in areas of extreme temperature, which exceed the allowable range.
Avoid installing in humid or dusty places.
Avoid installing in places where radiation is present.
Avoid installing in places where there are strong magnetic fields and electric signals.
Avoid installing in places where the camera would be subject to strong vibrations.
Never expose the camera to rain and water.
Mini Speed Dome Camera Introduction Manual
2
Features
1. Introduction
Product
2. Installation
3. Operation
4. How to use OSD Menu
5. Specifications
＆ Accessories
DIP Switch Setup
4
6
8
Cabling
10
Checking before Operation
12
Preset and Pattern Function Pre-Check
12
Start OSD Menu
13
Reserved Preset
13
Preset
14
Swing
14
Pattern
15
Group
16
Other Functions
17
OSD Display of Main Screen
18
General Rules of Menu Operation
19
Main Menu
19
Display Setup
20
Privacy Zone Mask Setup
21
Camera Module Setup
22
Motion Setup
24
Preset Setup
25
Swing Setup
26
Pattern Setup
27
Group Setup
28
Alarm Setup
29
System Initialize
30
Specifications
31
Dimension
32
Mini Speed Dome Camera Introduction Manual
3
█▐ Features ▌█
▌▌Camera Specifications
CCD Sensor: 1 / 4 " Interline Transfer CCD
Zoom Magnification: x 12 Optical Zoom, x 16 Digital Zoom (Max x 192 Zoom)
Day & Night Function
Various Focus Mode : Auto-Focus / Manual Focus / Semi-Auto Focus.
Independent
＆ Simultaneous Camera Characteristic Setup in Preset operation
▌▌Powerful Pan/Tilt Functions
Max. 300º /sec high speed Pan/Tilt Motion
Using Vector Drive Technology, Pan/Tilt motions are accomplished in a shortest path. As a result,
time to target view is reduced dramatically and the video on the monitor is very natural to watch.
For jog operation using a cont roller, since ultra slow speed 0.05 º/sec can be reached , it is very
easy to locate camera to desired target view. Additionally it is easy to move camera to a desired
position with zoom-proportional pan/tilt movement.
▌▌Preset, Pattern, Swing, Group, Privacy Mask and More...
MAX. 127 Presets are assignable and characteristics of each preset can be set up independently.
Max. 8 set of Swing action can be stored. This enables to move camera repetitively between two
preset positions with designated speed.
Max .4 of Patterns can be recorded and played back. This enables to move camera to follow any
trajectory operated by joystick as closely as possible.
Max- 8 set of Group action can be stored. This enables to move camera repetitively with
combination of Preset. A Group is composed of max. 16 entities of Preset.
Privacy Masks are assignable, not to intrude on other's privacy. (8 Privacy Zones)
▌▌PTZ(Pan/Tilt/Zoom)Control
With RS-485 communication, max. 255 of cameras can be controlled at the same time.
Pelco-D or Pelco-P protocol can be selected as a control protocol in the current version of firmware.
Mini Speed Dome Camera Introduction Manual
4
▌▌OSD (On Screen Display) Menu
OSD menu is provided to display the status of camera and to configure the functions interactively.
The information such as Camera ID, temperature, Pan/Tilt Angle, Alarm Input and Preset can be
displayed on screen.
▌▌I/O Functions (for External Mini Model)
To reject external electric noise and shock perfectly, alarm sensor Input is decoupled with photo
coupler.
Using the dry contact for alarm input.
If an external sensor is activated, camera can be set to move to the corresponding Preset position.
▌▌Reserved Presets for Special Purpose
Most camera characteristics can be set up easily and directly with reserved preset, not entering
into OSD menu. For more information, refer to “Reserved Preset” in this manual.
Mini Speed Dome Camera Introduction Manual
5
▌▌Product & Accessories
►Assembly
* Ceiling bracket is standard for mini PTZ Dome.
Option
Ceiling Bracket
(Do not support Internal PTZ Dome)
Pendant Bracket
L type
Wall Mount Bracket
ARM Type
Wall Mount Bracket
Mini Speed Dome Camera Introduction Manual
6
Option
Ceiling Bracket
Pendant Bracket
* Internal PTZ Dome built in a ceiling plate for installation.
L type
Wall Mount Bracket
ARM Type
Wall Mount Bracket
* ARM Type wall mount bracket is standard for External
mini PTZ Dome.
Mini Speed Dome Camera Introduction Manual
7
▌▌DIP Switch Setup
Before you install the camera, you should set the DIP switches to configure the camera ID,
communication baud rate.
Camera ID
PIN
Communication Baud Rate
1
2
3
4
5
6
7
8
A0
A1
A2
A3
A4
A5
A6
A7
Baud Rate
ON
1
2
4
8
16
32
64
128
Refer to
OFF
0
0
0
0
0
0
0
0
the Manual
FUNC.
9
10
►Camera ID Setup
ID number of camera is set using binary number. The example
is shown bellow.
PIN
1
2
3
4
5
6
7
8
ID Value
1
2
4
8
16
32
64
128
OSD menu setup
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
ex ) ID=5
ON
OFF
ON
OFF
OFF
OFF
OFF
OFF
ex ) ID=10
OFF
ON
OFF
ON
OFF
OFF
OFF
OFF
The range of ID is 1~255. Factory default of Camera ID is 1.
If you want to control a certain camera, you must match the
camera ID with Cam ID setting of DVR or Controller.
When DIP SW set all off the speed dome can change the ID
address and baud rate via OSD menu.
Mini Speed Dome Camera Introduction Manual
8
►Communication Baud Rate Setup
Select the appropriate Baud Rate with DIP
switch combination.
Switch State
Baud Rate
P9
P10
OFF
OFF
default 2400 bps
ON
OFF
2400 bps
OFF
ON
4800 bps
ON
ON
9600 bps
If you want to control using DVR or P/T
controller, their protocol must be identical to
camera. Otherwise, you can not control the
camera.
If you changed camera protocol by changing DIP
S/W, the change will be effective after you reboot
the camera.
Factory default of baud rate is 2400 bps. You
can change it in OSD menu.
Speed dome will detect the Pelco-D or
Pelco-P automatically in the Present
conditions.
Mini Speed Dome Camera Introduction Manual
9
▌▌Cabling
Cabling Terminal Block
►Power Connection
Please, check the voltage and current capacity of rated power carefully.
Rated power is indicated in the back of main unit.
Rated Power
Input Voltage Range
Current Consumption
DC 12V
DC 11V~13 V
0.8A
►RS-485 Communication
For PTZ control, connect this line to keyboard and DVR.
To control multiple cameras at the same time,
RS-485 communication lines of them is connected in parallel as shown below.
Mini Speed Dome Camera Introduction Manual
10
►Video Connection
Connect with BNC coaxial cable.
►Alarm input
Signal
Description
IN COM
Common point for alarm
IN1-,IN2-,IN3-, In4-,
Alarm input signal
Speed dome can detect the status of alarm input (NO or NC) automatically.
Normal Open and Normal Close define as below
Normal Open
No contact between alarm input and common point
Normal Close
Keeping contact between alarm input and common point
Mini Speed Dome Camera Introduction Manual
11
▌▌Check points before operation
Before power is applied, please check the cables carefully.
The camera ID of the controller must be identical to that of the target camera. The camera ID can be
checked by reading DIP switch of the camera.
If your controller supports multi-protocols, the protocol must be changed to match to that of the
camera.
If you changed camera protocol by changing DIP switch, the change will be effective after you reboot
the camera.
Since the operation method can be different for each controller available, refer to the manual for your
controller if camera can not be controlled properly. The operation of this manual is based on the
standard Pelco® Controller.
▌▌Preset and pattern Function Pre-Check
Check how to operate preset and pattern function with controller or DVR in advance to operate
camera function fully when using controller or DVR.
Refer to the following table when using standard Pelco® R protocol controller.
<Go Preset>
Press [Call] input [Preset number]and press [Enter]
<Set Preset>
Press [Preset] input [Preset number] and press [Enter]
<Run Pattern>
Press [Call] input [Pattern number] and press [Enter]
<Set Pattern>
Please refer to the pattern setup, turn to “Pattern Setup”
If controller or DVR has no pattern button or function, use shortcut keys with preset numbers. For
more information, refer to “Reserved Preset” in this manual.
Mini Speed Dome Camera Introduction Manual
12
▌▌Starting OSD Menu
Function
Using the OSD menu, Preset, Pattern, Swing, Group and Alarm Input function can be
configured for each application.
Enter Menu
Press <Call> + Preset Number [95] +<Enter>
▌▌Reserved Preset
Description
Some Preset numbers are reserved to special functions.
Function
<Call> [95]<Enter>
: Enters into OSD menu
<Call>[131~134]<Enter>
: Runs Pattern Function 1~4
<Call>[141~148]<Enter>
: Runs Swing Function 1~8
<Call>[151~158]<Enter>
: Runs Group Function 1~8
<Call>[200]<Enter>
: Runs the minimum angle of Horizontal scanning.
<Call>[160]<Enter>
: Sets Alarm ON
<Call>[161]<Enter>
: Sets Alarm OFF
<Call>[170]<Enter>
: Sets Camera BLC Mode to OFF
<Call>[171]<Enter>
: Sets Camera BLC Mode to ON
<Call>[174]<Enter>
: Sets Camera Focus Mode to AUTO
<Call>[175]<Enter>
: Sets Camera Focus Mode to Manual
<Call>[176]<Enter>
: Sets Camera Focus Mode to SEMI-AUTO
<Call>[177]<Enter>
: Sets Day & Night Mode to AUTO
<Call>[178]<Enter>
: Sets Day & Night Mode to NIGHT
<Call>[179]<Enter>
: Sets Day & Night Mode to DAY
<Call>[190]<Enter>
: Sets OSD Display Mode to AUTO
(Except Privacy Mask)
<Call>[191]<Enter>
: Sets OSD Display Mode to OFF (Except Privacy Mask)
<Call>[192]<Enter>
: Sets OSD Display Mode to ON (Except Privacy Mask)
<Call>[193]<Enter>
: Sets all Privacy Mask Display to OFF
<Call>[194]<Enter>
: Sets all Privacy Mask Display to ON
Mini Speed Dome Camera Introduction Manual
13
▌▌Preset
Function
Max 127 positions can be stored as Preset position. The Preset number can be
assigned from 1 to 128, but 95 is reserved for starting OSD menu.
Set Preset
<Preset>[1~128 ] <Enter> (Except [95])
Run Preset
<Call>[1~128 ] <Enter> (Except [95])
Delete Preset To delete Preset, use OSD menu.
→<PRESET SETUP>→<CLR PRESET>
<DOME CAMERA SETUP>
▌▌Swing
Function
By using Swing function, you can make camera to move between 2 Preset positions
repeatedly. When swing function runs, camera moves from the preset assigned as
st
the 1 point to the preset assigned as the 2nd point in CW (Clockwise) direction. Then
camera moves from the preset assigned as the 2nd point to the preset assigned as
the 1st point in CCW(Counterclockwise)direction.
Speed can be set up from 1° /sec to 180° /sec.
Set Preset
To set Swing, use OSD menu.
→<SWING SETUP>
<DOME CAMERA SETUP>
Run Swing
Ex: Run the first swing <Call>[141]<Enter>
Ex: Run the second swing <Call>[142]<Enter>
Delete Swing To delete Swing, use OSD menu.
→<SWING SETUP>→<CLEAR SWING>
<DOME CAMERA SETUP>
Mini Speed Dome Camera Introduction Manual
14
▌▌Pattern
Function
Pattern Function is that a camera memorizes the path (mostly curve path) by joystick
of controller for assigned time and revives the path exactly as it memorized.
4 Patterns are available and Maximum 150~180S or 500 communication commands
can be stored in a pattern.
Setup Pattern
→<PATTERN SETUP>→<EDIT PATTERN>
<DOME CAMERA SETUP>
□ Pattern editing screen is displayed as bellow.
□ Movement by Joystick and preset movement can be memorized in a pattern.
□ The recording time will be shown on the right-down corner
(Max 150~180S or 500 commands)
□ To save the recording, press OPEN key to save.
Run Pattern
Ex) Run Pattern 1: <Call>[131]<Enter>
Ex) Run Pattern 2: <Call>[132]<Enter>
Delete Pattern
Use OSD menu to delete Pattern
→<PATTERN SETUP>→<CLR PATTERN>
<DOME CAMERA SETUP>
Mini Speed Dome Camera Introduction Manual
15
▌▌Group
Function
The group function allows running sequence of Presets Max 8 group can be stored.
Each group can have max 16 preset can be set up in Group setup.
Dwell time between actions can be set up also.
Set Group
Use OSD Menu to create a Group
Run Group
Ex) Run Group 1: <Call>[151]<Enter>
Ex) Run Group 2: <Call>[152]<Enter>
Delete Group
Use OSD Menu to delete
→<GROUP SETUP>→<CLR GROUP>
<DOME CAMERA SETUP>
Mini Speed Dome Camera Introduction Manual
16
▌▌Other Functions
Power Up Action
This function enables to resume the last action executed before power down. Most of
actions such as Preset, Pattern, Swing and Group are available for this function but jog
actions are not available to resume.
Auto Flip
In case that tilt angle arrives at the top of tilt orbit (90º), zoom module camera keep
moving to opposite tilt direction (180º) to keep tracing targets. As soon as zoom
module camera passes through the top of tilt direction (90º), images should be reversed
automatically.
Parking Action
This function enables to locate the camera to specific position automatically if operator
doesn't operate the controller for a while. The Park Time can be defined as an interval
from 3 to 240 seconds.
Home Place
This function enables to adjust the camera in the best condition as the Home Place.
Privacy Zone Mask
To protect privacy, MAX. 8 Privacy Masks can be created on the arbitrary position to
hide objects such as windows, shops or private house. With Spherical Coordinates
system, powerful Privacy Zone Mask function is possible.
Global/Local Image Setup
WB(White Balance) and AE (Auto Exposure) and Brightness (1 to 100)can be set up
independently for each.
SemiAuto Focus
This mode exchanges focus mode automatically between Manual Focus mode and Auto
Focus mode by operation. Manual Focus mode activates in preset operation and Auto
Focus mode activates during jog operation With Manual mode at presets, Focus data is
memoried in each preset in advance and camera calls focus data in correspondence
with presets as soon as camera arrives at a preset. It should shorten time to get focuses
Focus mode changes to Auto Focus mode automatically when jog operation starts.
Mini Speed Dome Camera Introduction Manual
17
▌▌OSD Display of Main Screen
P/T/Z Information
Current Pan/Tilt angle in degree and a compass direction.
Camera ID
Current Camera ID (Address).
Action Title
Following are possible Action-Titles and their meaning.
"SET PRESET xxx"
When Preset xxx is stored
"GOTO PRESET xxx"
When camera reach to Preset xxx
"RUN PATTERN x"
When Pattern x is in action
“RUN SWG x / GROUP xxx”
"xxxxxx ERROR xxx"
When Swing is in action
When undefined function is called to run
Action Label
The Label stored for specific Preset and Pattern and Group.
Alarm Input
<for External Mini Model>
This information shows current state of Alarm Input. If an Input point is ON
state it will show a number corresponding to each point If an Input point is OFF
state, ' - ' will be displayed
Ex) Point 2 & 3 of inputs are ON, OSD will show as below
Temperature
Shows Show current speed dome internal temperature.
Mini Speed Dome Camera Introduction Manual
18
▌▌General Rules of Key Operation for Menu
The menu items surrounded with ( ) always has its sub menu.
For aIl menu level, to go into sub menu, press OPEN key or use joystick in the right.
To go to up-one-level menu, press CLOSE key or use joystick in the left.
To move from items to item in the menu, use joystick in the Up/Down.
To change a value of an item, use Up/Down of the joystick in the controller.
Press OPEN key or use joystick in the right to save values and Press CLOSE key or use joystick in the left to
cancel Values.
▌▌Main Menu
System Information
Displays system information and configuration.
Display Setup
Enable/Disable of OSD display on Main Screen
Dome Camera Setup
Configure various functions of this camera.
Alarm Setup
Configure alarm action.
System Initialize
Initializes system configuration and sets all data to factory default
configuration
Mini Speed Dome Camera Introduction Manual
19
▌▌Display Setup
This menu defines Enable/Disable of OSD display on Main
Screen.
If an item is set to be AUTO, the item is displayed only when
the value of it is changed.
Camera ID
[ON/OFF]
PTZ Information
[ON/OFF/AUTO]
Action Title
[ON/OFF/AUTO]
Alarm Input
[ON/OFF/AUTO]
Temperature
[ON/OFF/AUTO]
■ Compass Direction Setup
Set North to assign compass direction as criteria. Move
camera and press OPEN button to save.
Mini Speed Dome Camera Introduction Manual
20
▌▌Privacy Zone Mask Setup
<DISPLAY SETUP>
→<PRIVACY ZONE>
Select area in image to mask.
Mask No
[1~8]
Select Mask number. If the selected mask
has already data, camera moves as it was
set. Otherwise, “UNDEFINED” will be
displayed under “Mask No”.
Display
[ON/OFF]
Sets if camera makes mask shows or not on
images
Clear Mask [CANCEL/OK]
Deletes data in the selected mask NO.
■ Privacy Zone Area Setup
<DISPLAY SETUP>
→<PRIVACY ZONE>→<EDIT MASK>
Move camera to area to mask. Then the menu to adjust
mask size will be displayed.
By Pressing “OPEN” to enter, then press “OPEN” again,
the menu to adjust mask size will be displayed.
■ Privacy Zone Size Adjustment
Adjust mask size. Use joystick or arrow buttons to adjust mask
size.
● ◄ ► (TILT/WIDE)
Adjusts mask width.
● ▲ ▼(FAR/NEAR)
Adjusts mask height.
Mini Speed Dome Camera Introduction Manual
21
►Camera Setup
→<CAMERA SETUP>
<DOME CAMERA SETUP>
Setup the general functions of zoom camera module
Focus Mode [AUTO/MANUAL/SEMIAUTO]
Sets camera focus mode.
■ SEMIAUTO Mode
This mode exchanges focus mode
automatically between Manual Focus mode and
Auto Focus mode Manual Focus mode
activates in preset operation and Auto Focus
mode activates when jog operation Starts.
With Manual mode at presets, Focus data is
memorized in each preset in advance and
camera calls focus data in correspondence with
presets as soon as camera arrives at a preset
IRIS Mode
[AUTO/MANUAL/SEMIAUTO]
Sets camera IRIS mode.
Day/Night
[AUTO/DAY/NIGHT]
Sets camera day or night mode.
Digital Zoom [ON/OFF]
Sets digital zoom function to ON/OFF. If this is
set to OFF, optical zoom function runs but zoom
function stops at the end of optical zoom
magnification.
■ White Balance Setup
→<CAMERA SETUP>
<DOME CAMERA SETUP>
→<WHITE BALANCE SETUP>
WB Mode
[AUTO/MANUAL]
In Manual mode, Red and Blue level can be set
up manually
Red Adjust
Blue Adjust
～200]
[50～200]
[50
Mini Speed Dome Camera Introduction Manual
22
■ Auto Exposure Setup
<Dome Camera Setup>→<Camera Setup>
→<Auto Exposure Setup>
Backlight
[HIGH/NORMAL/OFF]
Sets Backlight Compensation
Brightness
[0∼100]
Adjusts brightness of images. Iris, Shutter
Speed and Gain are adjusted automatically in
correspondence with this value
Shutter
[DEFAULT/MANUAL/A.FLK]
If Shutter Speed is set to A. Flicker, to remove
Flicker, Shutter Speed should be set to 1/100
secretary.
／120 for PAL.
for NTSC and 1
AGC
[HIGH/MIDDLE/LOW/OFF]
Enhances image brightness automatically in
case that luminance level of image signal is too
low.
SSNR
[OFF/LOW/MIDDLE/HIGH]
Enhances images by deducting noises when
gain level of images is too high.
SENS-UP
[ON/OFF]
Activates Slow Shutter function when
luminance of Image (signal) is too dark
It is possible to set up the maximum number of
frames piled up one on another by Slow Shutter
function.
SENS-UP
[0~11]
The user can configure Sens-Up limit by
increasing/decreasing the shutter speed.
Mini Speed Dome Camera Introduction Manual
23
▌▌Motion Setup
→<MOTION SETUP>
<DOME CAMERA SETUP>
Setup the general functions of Pan/Tilt motions.
Motion Lock [ON/OFF]
Group. It is possible only to run those functions.
To set up and delete those functions, enter into
OSD menu.
Power Up Action [NORTH/GROUP/PATTERN/SWING]
Refer to "Other Functions" section.
Auto Flip
[ON/OFF]
Refer to "Other Functions" section.
H.REVERSE [ON/OFF]
Flip horizontal
Jog Direction [INVERSE/NORMAL]
If you set this to 'Inverse', the view in the
screen is moving same direction with jog
tilting. If 'Normal' is selected, the view in
the screen is moving reversely.
Jog Max Speed
[1º /sec∼300º /sec]
Sets maximum jog speed. Jog speed is
inversely proportional to zoom magnification.
As zoom magnification goes up, pan/tilt speed
goes down
Freeze in Preset [ON/OFF]
At start point of preset movement, camera
starts freezing the image of start point. Camera
keeps displaying the image of start point
during preset movement and does not display
the images which camera gets during preset
movement. As soon as camera stops at preset
end point, camera starts displaying live images
which it gets at preset end point.
This function availability should be different by
models.
Mini Speed Dome Camera Introduction Manual
24
■ Parking Action Setup
<DOME CAMERA SETUP>→<MOTION SETUP>
→<PARKING ACTION SETUP>
If Park Enable is set to ON, camera runs assigned function
automatically if there is no PTZ command during assigned
''Wait Time''.
Wait Time
[003~240S]
The time is displayed with "XXX S" format
and you can change this joystick or
keyboard..
Park Action [NOTHING/PATTERN/SWING/GROUP]
Ex) If you set park action is HOME, the
camera will move to home position when
there is no PTZ command during assigned
"Wait Time".
▌▌Preset Setup
<DOME CAMERA SETUP>→<PRESET SETUP>
Preset Number
[1~128] (Except [95])
If a selected preset is already defined,
camera moves to pre- defined position. If a
selected preset is not defined. "UNDEFINED"
shows on monitor.
／OK]
Clear Preset [CANCEL
Delete current Preset data (include edit label)
Clear all Preset
／OK]
[CANCEL
Delete all current Preset data (include edit
label)
Edit Scene
Redefine current Preset scene position Using
Joystick move camera to desired position, By
pressing OPEN to save current PTZ data.
Edit Label
Edits Label to show on monitor when preset
runs MAX. 18 alphabets are allowed. Enter
edit label, “?” cursor will be displayed on the
screen, using up/down of joystick to select
character, and using left/right to move cursor.
After inputting, press “OPEN” key to save and
exit the setting.
Mini Speed Dome Camera Introduction Manual
25
▌▌Swing Setup
<Dome Camera Setup>→<Swing Setup>
Swing Number
[1~8]
Selects Swing number to edit.
Start PositionSet up the 2 position for Swing function if a
End Position
selected preset is not defined,
"UNDEFINED" will be displayed.
When swing function runs, camera moves
form the preset assigned as the start point
to the preset assigned as the end point in
CW (Clockwise) direction. The camera
moves from preset assigned as the start
point to preset assigned as the end point
CCW(Counterclockwise) direction.
Then camera moves from the preset
assigned as the endpoint to the preset
assigned as the start point in CCW
(Counterclockwise) direction.
Swing Speed [001~180 ]
Sets Swing speed from 001 to 180.
Clear Swing [CANCEL/OK]
Deletes current Swing data
Run Swing
Run current Swing
Mini Speed Dome Camera Introduction Manual
26
▌▌Pattern Setup
<DOME CAMERA SETUP>→<PATTERN SETUP>
Pattern Number
[1~4]
Selects Pattern number to edit.
If a selected pattern number is not defined,
"UNDEFINED" will be displayed under
selected pattern number.
Clear Pattern [CANCEL/OK]
Deletes data in current pattern
Label Display [ON/OFF]
Edit Pattern
[OK/CANCEL]
OK: Edit the pattern function
Cancel: Don't execute the pattern function.
▌▌Edit Pattern
Edit Pattern
Starts editing pattern. By using Joystick, move
to start position with appropriate zoom. To start
pattern recording, press OPEN key. To exit this
menu, press CLOSE key. Move camera with
joystick of controller or run preset function to
memorize the path (mostly curve path) in a
selected pattern. Maximum 500 commands can
be stored in a pattern
Edit Label
Edits Label to show on monitor when preset
runs MAX. 18 alphabets are allowed. Enter edit
label, “?” cursor will be displayed on the screen,
using up/down of joystick to select character,
and using left/right to move cursor, After
inputting, press “OPEN” key to save and exit
the setting.
Run Pattern Run current Pattern
Mini Speed Dome Camera Introduction Manual
27
▌▌Group Setup
<Dome Camera Setup>→<Group Setup>
Croup Number
[1~8]
Selects Group number to edit.
If a selected Group number is not defined,
"UNDEFINED" will be displayed under
selected Group number.
Clear Group [CANCEL/OK]
Deletes data in current Group
Edit Group
Starts editing Group.
Edit Label
Edits Label to show on monitor when preset
runs MAX. 18 alphabets are allowed. Enter
edit label, “?” cursor will be displayed on the
screen, using up/down of joystick to select
character, and using left/right to move cursor,
After inputting, press “OPEN” key to save and
exit the setting.
Run Group
▌▌Edit Group
Run current Group
<Dome Camera Setup>→<Group Setup>→<Edit Group>
1. Press OPEN key to start Tour setup.
2. Note that MAX. 16 “Presets” are allowed in a Tour.
Move
cursor up/down and press OPEN key to set up.
3. Set up Action, Dwell time and Speed is optional. Time value
from displayed in reverse. Move cursor Left/Right to select
items and 3 sec To 240 sec. Speed value from 50 to 300.
Move cursor Left/Right to select items and move cursor
Up/Down to change each value.
Mini Speed Dome Camera Introduction Manual
28
▌▌Alarm Input Setup (For External mini PTZ Dome only)
→<ALARM SETUP>
<DOME CAMERA SETUP>
Match the Alarm sensor input to one of Preset Positions
/Home/Auto Scan/Group/Pattern/Swing. If an external sensor
is activated, camera will corresponding command position
when this item is predefined.
Alarm Enable
[ON/OFF]
Establish the current passage reports to the
police open of function with pass
Alarm No.
[001~004]
Select alarm channel number
Alarm x Action
[NOTHING/PRESET/PATTERN/SWING/
GROUP]
Assign counteraction Preset position to each
Alarm input.
Release Time
[001~240 S]
Alarm output time is postponed to a certain
time, adjustable range is 0 sec t 240 sec.
Start Fan
[20~60ºC]
Ex) If set start fan is 30ºC, the dome will start
fan when above 30ºC, and it will stop to fan
when temperature is lower than set value
5ºC.
Start Heater [-20~10ºC]
Ex) If set start fan is -10ºC, the dome will start
heat when above -10ºC, and it will stop to
heat when temperature is higher than set
value 5ºC.
Mini Speed Dome Camera Introduction Manual
29
▌▌System Initialize
Clear All Data
Deletes all configuration data such as
display, camera, motion setup and so on.
Clear Display Set Initializes Display Configuration
Clear Camera Set Initializes Camera Configuration
Clear Motion Set Initializes Motion Configuration
Clear Edit Data
Deletes Preset Date, Swing Data,
Pattern Data and Group Data
Reboot Camera
Reboots Zoom Camera module
Reboot System
Reboots Speed Dome Camera
■ Initial Configuration Table
Display Configuration
Camera Configuration
Camera ID
ON
Focus Mode
SemiAu to
PTZ Information
AUTO
Iris Mode
SemiAu to
Action Title
AUTO
Digital Zoom
OFF
Alarm Input
AUTO
Day & Night
AUTO
Temperature
AUTO
White Balance
AUTO
<Set North Direction>
Backlight
OFF
<Privacy Zone>
Brightness
50
Shutter
DEFAULT
AGC
HIGH
Motion Configuration
Motion Lock
OFF
SSNR
MID DLE
Power Up Action
NOTHING
SENS-UP
ON
Auto Flip
OFF
User Edit Data
Jog Max Speed
300º/sec
Preset 1~128
Undefined
Jog Direction
NORMAL
Swing 1~8
Undefined
Freeze In Preset
OFF
Pattern 1~4
Undefined
Park Action
NOTHING
Group 1~8
Undefined
Mini Speed Dome Camera Introduction Manual
30
▌▌Specifications
Type
Mini
External mini
Video Signal System
NTSC / PAL
CCD
1/4" Interline Transfer CCD
Max. Pixels
NTSC: 811(H)×508(V)410K / PAL: 795(H)×596(V)470K
Effective Pixels
NTSC: 768(H)×494(V)380K / PAL: 752(H)×582(V)440K
Horizontal Res.
600 TV Line(Color), 680 TV Line(B/W)
S/N
Ration 52 dB (AGC Off)
Zoom
x12 Optical zoom, x16 Digital Zoom
Focal length
Min. Illumination
f=3.94 ~ 46.05 mm (F1.67~1.88)
0.2 Lux /F1.67(50 IRE)Color / 0.02 Lux F1.67 (50 IRE)B/W
Day & Night
Auto / Day(Color)/ Night(ICR, B/W)
Focus
Auto / Manual / Semi Auto
Iris
Auto / Manual / Semi Auto
Shutter
Pal: x128 ~ 1/120000 sec
AGC
White Balance
Low / Middle / High / Off
Auto / Manual(Red, Blue Gain Adjustable)
BLC
Normal / High / Off
SSNR UP
ON/OFF
SSNR
Low / Middle / High / Off
Pan : 360°(Endless)
SSNR Pan/Tilt Speed
Tilt : 180°(Auto-Flip), 95°(Normal)
Go to Preset Speed : 1~300°/sec
Preset
Manual : 0.05~300°/sec
127 Preset(Label)
Pattern
4 Pattern, 1200 commands /Pattern
Swing
8 Swing/Speed:1~180/sec
Group
8 Group (20 action entities per Group)
Direction
INVERSE / NORMAL
Other Functions
Auto flip, Auto Parking, Power Up Action etc.
Communication
RS-485(9600, 4800, 2400 Select table or change from OSD menu)
Protocol
Pelco-D, Pelco-P, Auto identify
Privacy Zone
Alarm Input
8 Zone
No
OSD
Fan and Heater
4 Input
Menu / PTZ information etc
No
Yes
DC 12V / 0.8A
DC 12V / 1.1A
Ø128 x 187(H)mm
Ø190 x 144(H)mm
Weight
about 2.4Kg
about 2.6Kg
Operating Temp.
0°C ~ 40°C
-30°C ~ 50°C
Rated Power
Dimension
Mini Speed Dome Camera Introduction Manual
31
▌▌Dimension
► Ceiling Bracket
► Pendant Bracket
►ARM Type Wall Mount Bracket
►L Type Wall Mount Bracket
V.20111226
Mini Speed Dome Camera Introduction Manual
32