BACKPACK SPRAYER JACTO PJBc

BACKPACK SPRAYER JACTO PJBc
12. Important Return Safety Instructions
If it is necessary to return the sprayer for repair, always perform
the following:
ters, seals, rechargeable battery, hydraulic pump, electronic
panel, charger and its cables, agitator lever, belt, UNLESS
THEY SHOW DEFECTS IN WORKMANSHIP, ASSEMBLY OR
MATERIAL.
• Damages resulting from accidents.
1.
Flush chemical residue from the pump, tank and hoses
(performed in an approved containment area).
2.
Circulate fresh water in the tank, pump and hoses.
3.
Tag the sprayer with type of chemicals that have been
sprayed.
4.
Include complete description of operation problem, such
as how sprayer was used, symptoms of malfunction, how
many working hours per day, etc.
Operator’s Manual - English
BACKPACK SPRAYER JACTO PJBc
Edition Nº 1231339
10/2015
• Transportation or freight of the equipment, parts and components in case such warranty is not approved.
• Transportation and travel time of technicians.
5.
Remove the battery from the sprayer and keep it in clean
and dry conditions. Battery must accompany the sprayer
when it is returned for repairs.
Since the sprayer can contain residues of toxic chemicals, these
steps are necessary to protect all the people who handle return
shipments, and to help identify the reason for the breakdown.
13. Statement of Limited Warranty
MÁQUINAS AGRÍCOLAS JACTO S.A. shall warrant the equipment
described in this manual and shall repair or replace parts and
components which, under normal operation and wear, in accordance with technical recommendations, show DEFECTS IN MATERIAL OR WORKMANSHIP, based on the following conditions.
13.5. General terms
• Parts replaced within the warranty period shall be property
of JACTO.
• The warranty on replaced parts and components shall expire together with the equipment warranty period.
• Eventual delays in performing services shall not give the
owner right either to indemnity or to extension of the warranty period.
• JACTO reserves the right to modify its products or to interrupt the manufacture without prior notice.
• Any suggestion, questions and complaints shall be submitted to CUSTOMER CARE SERVICE: Jacto Incorporated - 19217
SW 119th Ave. - Tualatin OR, 97062 - Phone: 1-800-522-8610
- Fax: 1-800-511-3671 - Email: [email protected]
13.1. Warranty period
03 (three) years from the date of sale to the original purchaser.
13.2. Warranty application
JACTO shall honor this warranty, free of charge, if any part or
component shows defect in MATERIAL OR WORKMANSHIP, after
final analysis at the factory.
13.3. This warranty shall be null & void in
case of:
• Misuse of the equipment against specifications in this manual, overwork or accidents.
• Use the equipment to spray products not intended for
plants protection or not approved by regulatory authorities
to be used with knapsack sprayers.
• Preventive/remedial maintenance performed by unauthorized people.
• Use of parts and components not supplied by JACTO.
• Modification of the equipment or any characteristic of the
original design.
13.4. This warranty shall exclude
• Parts which show wear and tear due to use: spray nozzle, fil-
16/16
Manufactured by INTERMAN Corporation Ltd.
under license of Máquinas Agrícolas Jacto S.A.
Rojana Industrial Park (Rayong)
3/3, Moo 2, Bankhai-Banbueng Rd.T. Nongbua.
A.Bankhai Rayong 21120 - Thailand
Website: www.jacto.com
Customer assistance: JACTO INC.
19217 SW 119 th Ave.
Tualatin, Oregon 97062
Tel: (503) 885-8723
Fax: (800) 511-3671
Toll free: (800) 522-8610
E-mail: [email protected]
Home page: www.jacto.com
SUMMARY
1. Introduction
2. Specifications
3. General Power Tool Safety Warnings
3.1. Work area safety
3.2. Electrical safety
3.3. Personal Safety
3.4. Power tool use and care
3.5. Battery tool use and care
3.6. Service
4. Symbols
5. Important Safety Instructions for Battery Chargers
5.1. Charging procedure
5.2. Important charging notes
6. Important Safety Instructions for Battery Packs
7. Important Safety Instructions for Sprayers
7.1. Triple rinse of empty agrochemicals containers
8. Operating Instructions
8.1. Select the correct nozzle
8.2. Calibration of battery powered backpack sprayer
8.3. Filling the spray tank with pesticides
8.4. Shoulder strap adjust (16c and 20c)
8.4. Shoulder strap adjust (8c)
8.6. Turn On/Off the sprayer
8.7. Application
9. Maintenance
10. Parts list
10.1 PJB-16c/PJB-20c
10.2 PJB-8c
11. Troubleshooting
12. Important Return Safety Instructions
13. Statement of Limited Warranty
13.1. Warranty period
13.2. Warranty application
13.3. This warranty shall be null & void in case of
13.4. This warranty shall exclude
13.5. General terms
11. Troubleshooting
3
3
3
3
3
3
4
4
4
4
4
5
5
6
6
7
8
8
8
8
9
9
9
9
10
11
11
13
15
16
16
16
16
16
16
16
If sprayer is not working as expected, consider the following table before contacting technical assistance.
Malfunction / Status
Trigger valve is not released
Sprayer is turned ON, but
pump is not working (no
audible noise from pump)
Cause
Action
Trigger valve is shut
Release trigger valve
Pump electrical connector is
disconnected
Connect pump electrical connector
Nozzle or nozzle filter is blocked
Clean or replace nozzle or filter
Pump wiring is broken
Trigger valve is released
Contact technical assistance
Pump is damaged
Battery is fully discharged
Battery is permanently damaged or
electronic module is damaged
Trigger valve is not released
Pump is working, but
spray is not coming out
Trigger valve is released
Recharge battery
Contact technical assistance
Trigger valve is shut
Release trigger valve
Nozzle or nozzle filter is blocked
Clean or replace nozzle or filter
Pump suction is blocked (inside
chemical tank)
Suction hose is blocked or disconnected
Contact technical assistance
Pump or hoses are leaking
Air accumulation inside the lance
Place the lance with the trigger
valve pressed above the base of the
sprayer until the spray jet begins to
spray continuously
Pump suction is partially blocked
(inside chemical tank)
Remove obstruction and circulate
fresh water to clean hoses
Suction hose is partially blocked
Circulate fresh water to clean hoses
Pump or hoses are leaking
Contact technical assistance
Nozzle or filters are blocked or
damaged
Clean or replace nozzle or filter
ON/OFF button was pressed
Pump reached maximum pressure,
pressure switch activated
Verify if the nozzle is clogged. Clean it
No audible noise from pump
Pump wiring is loose, damaged or
disconnected
Check pump wiring
Battery is not being fully charged
Charge battery until charger LED
indicator is green
Not original JACTO charger
Use original JACTO charger
Not original pump (excessive load)
Use original pump
Damaged charger or charger cords/
plugs
Replace charger
Sprayer sprays but is abnormal or spray pressure
is weak
Spraying was normal but
stopped suddenly
Battery charge is not
lasting as usual or is not
charging at all
New battery
Battery is damaged (wet, pierced,
broken terminals…)
Used battery (more than 300
recharge cycles)
Replace battery
Battery life cycle is near the end
15/16
1. Introduction
3. General Power Tool Safety Warnings
This manual contains information for the proper assembly, operation and care of your sprayer. Carefully read and follow the
instructions contained in this manual before using your sprayer.
This equipment was designed for spraying plants protection
products approved by regulatory authorities to be used in knapsack sprayers.
2. Specifications
Read all safety warnings and all instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or
serious injury.
Model
PJBc - 20/16/8
SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE.
Maximum dimensions (L x W x H)
15 in. X 8 in. X 21 in.
(385 mm x 205 mm x 532 mm)
15 in. X 8 in. X 18.5 in.
(385 mm x 205 mm x 462 mm)
10 in. X 6 in. X 16.4 in.
(255 mm x 159 mm x 417 mm)
The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Net weight
8.8 lbs / 7.1 lbs / 5.3 lbs (4.0 kg / 3.2
kg / 2.4 kg)
Gross weight
Spray lance length
Hose length
52.9 lbs / 42.3 lbs / 22.9 lbs (24 kg /
19.2 kg / 10.4 kg)
23.6 in / 23.6 in / 13.8 in (600 mm /
600 mm / 350 mm)
53 in / 53 in / 65 in (1350 mm /
1350 mm / 1650 mm)
Chemical tank
3.1. Work area safety
a. Keep work area clean and well lit. Cluttered or dark areas
invite accidents.
b. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Power tools create sparks which may ignite the dust or
fumes.
Capacity
5.3 gal. / 4.2 gal / 2.1 gal
(20L / 16L / 8L)
Residual volume
None
c. Keep children and bystanders away while operating a
power tool. Distractions can cause you to lose control.
Filling opening diameter
4.5 in / 4.5 in / 3.9 in (115 mm / 115
mm / 100 mm)
3.2. Electrical safety
Material
Polyethylene
Pump
Type
Diaphragm
Maximum pressure
60 psi (4.1 bar)
Open flow
0.50 gpm (1.9 L/min)
Nozzle installed
Blue adjustable cone
Battery
Type
Lithium Ion, rechargeable
Rated Voltage
10.8 V d.c.
Capacity
20 Wh (2200 mAh)
Recharge time
6 hours
a. Power tool plugs must match the outlet. Never modify
the plug in any way. Do not use any adapter plugs with
earthed (grounded) power tools. Unmodified plugs and
matching outlets will reduce risk of electric shock.
b. Avoid body contact with earthed or grounded surfaces
such as pipes, radiators, ranges and refrigerators. There
is an increased risk of electric shock if your body is earthed or
grounded.
c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
SAFETY GUIDELINES – DEFINITIONS
d. Do not abuse the cord. Never use the cord for carrying,
pulling or unplugging the power tool. Keep cord away
from heat, oil, sharp edges or moving parts. Damaged or
entangled cords increase the risk of electric shock.
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING
PROBLEMS. The symbols below are used to help you recognize this information.
e. When operating a power tool outdoors, use an extension
cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
f. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
DANGER!
WARNING!
Indicates a potentially hazardous situation which, if not avoided,
could result in death or serious injury.
CAUTION!
Indicates a potentially hazardous situation which, if not avoided,
may result in minor or moderate injury.
14/16
WARNING!
3.3. Personal Safety
a. Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use a power
tool while you are tired or under the influence of drugs,
alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
3/16
b. Use personal protective equipment. Always wear eye
protection. Protective equipment such as dust mask, non-skid
safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
c. Prevent unintentional starting. Ensure the switch is in
the off-position before connecting to power source and/
or battery pack, picking up or carrying the tool. Carrying
power tools with your finger on the switch or energizing power
tools that have the switch on invites accidents.
d. Remove any adjusting key (wrench, screwdriver…) before
turning the power tool on. A wrench or a key left attached to
a rotating part of the power tool may result in personal injury.
e. Do not overreach. Keep proper footing and balance at all
times. This enables better control of the power tool in unexpected situations.
f. Dress properly. Do not wear loose clothing or jewellery.
Keep your hair, clothing and gloves away from moving
parts. Loose clothes, jewellery or long hair can be caught in
moving parts.
g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce
dust-related hazards.
3.4. Power tool use and care
a. Do not force the power tool. Use the correct power tool
for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
b. Do not use the power tool if the switch does not turn it
on and off. Any power tool that cannot be controlled with the
switch is dangerous and must be repaired.
c. Disconnect the plug from the power source and/or the
battery pack from the power tool before making any adjustments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the
power tool accidentally.
d. Store idle power tools out of the reach of children and do
not allow persons unfamiliar with the power tool or these
instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other
condition that may affect the power tool’s operation. If
damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly maintained
cutting tools with sharp cutting edges are less likely to bind and
are easier to control.
g. Use the power tool, accessories and tool bits etc., in accordance with these instructions, taking into account the
working conditions and the work to be performed. Use
of the power tool for operations different from those intended
could result in a hazardous situation.
3.5. Battery tool use and care
4/16
a. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may
create a risk of fire when used with another battery pack.
10.2. PJB-8c
Nº
Code
Description
b. Use power tools only with specifically designated battery
packs. Use of any other battery packs may create a risk of injury
and fire.
1
560573
DIAPHRAGM LID (NITRILE)
1
2
1210726
LID XP WITH DIAPHRAGM
1
3
1168414
STRAINER XP
1
c. When battery pack is not in use, keep it away from other
metal objects like paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connection
from one terminal to another. Shorting the battery terminals
together may cause burns or a fire.
4
1224653
PJB-8c STRAP COMPLETE
1
5
1224654
TANK PJB-8c JACTO
1
6
1168418
FILTER LP-3
1
7
1224183
BASE PJB-8c
1
d. Under abusive conditions, liquid may be ejected from
the battery, avoid contact. If contact accidentally occurs,
flush with water. If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may cause irritation or burns.
8
1168544
TRIGGER VALVE CAP AND O-RING
2
9
1220934
O-RING OR1-019
2
10
1180613
STAINLESS STEEL SPRING 9,2
1
11
1168422
NEEDLE LP-3 WITH O-RINGS
1
12
1168421
TRIGGER VALVE LEVER
1
13
1168419
TRIGGER VALVE ASSEMBLY LP-3
1
14
1221557
DUST COVER
1
1
e. Do not use a battery pack or appliance that is damaged
or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
f. Do not expose a battery pack or appliance to fire or excessive temperature. Exposure to fire or temperature above 60°C
may cause explosion.
3.6. Service
a. Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure
that the safety of the power tool is maintained.
4. Symbols
The label on your tool may include the following symbols. The
symbols and their definitions are as follows:
V
volts
A
amperes
W
watts
Hz
hertz
Bar
Bar
min
h
n0
l
no-load speed
Qty.
15
1224664
HOSE KIT PJB 8c
16
1220925
CLAMP SIMPLEX D 12-14 STEEL
5
17
1168397
BASE LOCK XP
2
18
915744
SCREW CAP 11/16”
2
19
909309
CONE PACKING
2
20
1224677
LANCE PJB-8c COMPLETE
1
21
1224680
SPRAYER HOSE PJB-8c
1
22
1220634
IN-LINE FILTER
1
23
1220632
PJB PUMP FILTER KIT
1
24
635276
ELBOW 11/16”-16 UN
1
25
592139
NOZZLE FILTER M50/60
1
26
325787
BLUE ADJUSTABLE CONE NOZZLE
1
27
1220622
FLANGE HEAD SCREW PHILLIPS 5X12 MM
4
1
ou d.c.
direct current
28
1220639
DIAPHRAGM PUMP - COMPLETE
ou a.c
alternating current
29
1231358
BATTERY CHARGER LI-ION 12.4V IEC TYPE A
1
earthing terminal
30
1224719
LI-ION BATTERY JB 1220
1
litres
31
1224693
BASE COVER PJB-8c
1
32
1220947
SCREW PAN HEAD M 5X0,8X 12
1
minutes
kg
kilograms
hours
m
meters
5. Important Safety Instructions for
Battery Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety instructions for battery chargers. Before using charger,
read all instructions and cautionary markings on charger, battery pack, and product using battery pack.
WARNING:
Shock hazard. Do not allow any liquid to get
inside charger.
13/16
CAUTION!
• Burn hazard. To reduce the risk of injury,
charge only designated JACTO batteries.
Other types of batteries may burst causing
personal injury and damage.
32
29
33
26
30
WARNING!
28
34
05
27
25
24
23
35
14
22
19
21
17
18
15
20
17
13
16
09
05
03
04
06
07
12
11
08
10
02
01
36
• DO NOT attempt to charge the battery
pack with any chargers other than the
ones in this manual. The charger and
battery pack are specifically designed to
work together.
• These chargers are not intended for any
uses other than charging designated
JACTO lithium rechargeable batteries.
Any other uses may result in risk of fire,
electric shock or electrocution.
• Do not expose charger to rain or snow.
• Pull by plug rather than cord when disconnecting charger. This will reduce risk of
damage to electric plug and cord.
• Make sure that cord is located so that it
will not be stepped on, tripped over, or
otherwise subjected to damage or stress.
• Do not use an extension cord unless it
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock, or electrocution.
• An extension cord must have adequate
wire size (AWG or American Wire Gauge)
for safety. When using more than one
extension to make up the total length, be
sure each individual extension contains at
least the minimum wire size. When using
an extension cord, be sure to use one heavy
enough to carry the current that product will
draw. An undersized cord will cause a drop
in line voltage resulting in loss of power and
overheating. The following table shows the
correct size to use depending on cord length
and nominal current presented in the label of
the charger mentioned in this manual. If in
doubt, use the next heavier gauge.
Up to
15.2 m
From 15.2 m
and up to 30 m
More than 30 m
Wire Size (AWG)
16
14
Not recommended
Wire Size (mm2)
1.5
2.5
Not recommended
• Do not mount charger on wall or permanently affix charger to any surface. The
charger is intended to use on a flat, stable
surface (i.e., table top, bench top).
• Do not operate charger with damaged
cord or plug - have them replaced immediately.
• Do not operate charger if it has received a
sharp blow, been dropped, or otherwise
damaged in any way. Take it to an authorized service center.
• Do not disassemble charger; take it to
an authorized service center when service
or repair is required. Incorrect reassembly
may result in a risk of electric shock, electrocution or fire.
• Disconnect the charger from the outlet
before attempting any cleaning. This will
reduce the risk of electric shock. Removing the
battery pack will not reduce this risk.
• NEVER attempt to connect 2 chargers
together.
• The charger is designed to operate on
standard household electrical power. Do
not attempt to use it on any other voltage.
• Battery chargers contain electronic parts.
Dispose of properly.
• Under certain conditions, with the charger
plugged in to the power supply, the charger
can be shorted by foreign material. Foreign
materials of a conductive nature such as, but
not limited to, steel wool, aluminum foil, or
any buildup of metallic particles should be
kept away from charger contacts. Always
unplug the charger from the power supply
when not charging battery. Unplug charger
before attempting to clean.
31
Extension Cord
Total Length
5.1. Charging procedure
JACTO charger provided with this sprayer is designed to charge
JACTO battery pack model JB1220 in 6 hours.
1.
Turn off the sprayer. Ensure the button on the electric panel is in “OFF” position. IMPORTANT NOTE: If the sprayer ON/
OFF switch is in “ON” position, battery will not recharge!
2.
Connect the charger plug to the battery recharge plug in
the electric panel.
3.
The charge light will remain red/orange while charging.
4.
When battery pack is fully charged, charge light will
change its color to green.
5.
As soon as the battery is fully charged, disconnect the battery from the charger.
6.
Unplug charger from outlet.
Recharge discharged batteries as soon as possible or battery life may be greatly diminished. For longest battery life,
do not discharge batteries fully. It is recommended that the
batteries be recharged after each use.
5.2. Important charging notes
12/16
5/16
• DO NOT charge the battery pack in an air temperature below
32 °F (0 °C) or above 113 °F (45 °C). This is important and will
prevent serious damage to the battery pack.
• The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and does
not indicate a problem. To facilitate the cooling of the battery
pack after use, avoid placing the charger or battery pack in a
warm environment such as in a shed.
• Do not freeze or immerse charger in water or any other liquid.
6. Important Safety Instructions for
Battery Packs
WARNING:
For safe operation, read this manual and
manuals originally supplied with tool
before using the charger. When opening
the tool package for the first time, the battery
pack will not be fully charged. Before using
the battery pack and charger, read the safety
instructions below. Then follow charging
procedures outlined.
READ ALL INSTRUCTIONS
• Do not incinerate the battery pack even if it is severely
damaged or is completely worn out. The battery pack can
explode in a fire. Toxic fumes and materials are created when
battery packs are burned.
• Do not charge or use battery in explosive atmospheres,
such as in the presence of flammable liquids, gases or
dust. Inserting or removing the battery from the charger may
ignite the dust or fumes.
• If battery contents come in to contact with the skin, immediately wash area with mild soap and water. If battery
liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the
battery electrolyte for Li-ion batteries is composed of a mixture
of liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause respiratory
irritation. Provide fresh air. If symptoms persist, seek medical
attention.
• Disposal of used batteries must be made at appropriate
locations and approved for receiving such material. If a
recycling center is not available in your area please contact CUSTOMER SERVICE: Jacto Inc. 19217 SW 119th Ave. Tualatin, OR
97062 - Phone 1-800-522-8610 - Email: [email protected] - Website: www.jacto.com
WARNING!
Burn hazard. Battery liquid may be flammable
if exposed to spark or flame.
• Charge the battery packs only in JACTO
chargers.
6/16
• DO NOT splash or immerse in water or
other liquids. This may cause premature
cell failure.
• Do not store or use the tool and battery
pack in locations where the temperature
may reach or exceed 113°F (45 ºC).
• Never attempt to open the battery pack for
any reason. If battery pack case is cracked or
damaged, do not connect to charger. Do not
crush, drop or damage battery pack. Do not
use a battery pack or charger that has been
dropped, run over or damaged in any way
(i.e., pierced with a nail, hit with a hammer,
stepped on). Damaged battery packs should
be returned to service center for recycling.
• Fire hazard. Do not store or carry battery so that metal objects can contact
exposed battery terminals. For example,
do not place battery in aprons, pockets, tool
boxes, product kit boxes, drawers, etc., with
loose nails, screws, keys, etc. Transporting
batteries can possibly cause fires if the
battery terminals inadvertently come in
contact with conductive materials such
as keys, coins, hand tools and the like.
Certain regulations prohibit transporting
batteries on airplanes (i.e., packed in suitcases and carry-on luggage) UNLESS they
are properly protected from short circuits.
So when transporting individual batteries,
make sure that the battery terminals are
protected and well insulated from materials
that could contact them and cause a short
circuit. NOTE: Batteries should not be put
in checked baggage.
7. Important Safety Instructions for
Sprayers
DANGER!
• DO NOT spray flammable or combustible
chemical products. This will result in serious
risk of fire and explosion.
• DO NOT spray acids or corrosive chemicals. This will result in serious risk of fire,
explosion and leakage. Sprayer parts can
be permanently damaged.
WARNING!
• DO NOT use the sprayer for purposes
other than spraying agricultural defensives approved by competent authorities.
Always consider the following recommendations:
• Check sprayer before spraying. Ensure
there is no leakage or missing parts. Do not
use sprayer if it is not in good condition.
• Do not eat, drink or smoke while spraying.
A
10. Parts list
B
10.1. PJB-16c/ PJB-20c
C
D
• Only fill the tank with a water soluble agrochemical or an already mixed powder liquid form through the filling filter. Do
not prepare mixtures directly in the sprayer tank;
Nº
Code
Description
1
1220947
SCREW PAN HEAD M 5X0, 8X 12
Qty.
1
2
1220640
BASE COVER
1
3
1231358
BATTERY CHARGER LI-ION 12.4V IEC TYPE A
1
4
1168397
BASE LOCK XP
1
5
1168544
TRIGGER VALVE CAP AND O-RING
2
6
1220634
IN-LINE FILTER
1
7
1220934
O-RING OR1-019
1
8
1220632
PJB PUMP FILTER KIT
1
9
1224055
HOSE KIT PJB-c
1
10
325787
BLUE ADJUSTABLE CONE NOZZLE
1
11
592139
FILTER M50/60
1
12
635276
ELBOW 11/16”-16 UN
1
13
909309
CONE PACKING
2
14
915744
SCREW CAP 11/16”
2
1
15
100131
EXTENSION
16
1220925
CLAMP SIMPLEX D 12-14 STEEL
6
17
1220622
FLANGE HEAD SCREW PHILLIPS 5X12 MM
6
18
1220636
CONNECTOR NUT
1
19
1220635
HOSE CONNECTOR
1
20
1220639
DIAPHRAGM PUMP - COMPLETE
1
21
1224057
COMPLETE PANEL PJB-c
1
22
1220641
BASE PJB
1
23
1224059
AGITATOR COVER
1
24
1168422
NEEDLE LP-3 WITH O-RINGS
1
• The spray lance can be conveniently stored on the clips on
the side of the tank;
25
1180613
STAINLESS STEEL SPRING 9,2
1
26
1224062
COMPLETE HOSE FOR LP3 PJB-c
1
• Ensure that there is no liquid waste in the sprayer, especially
in harsh winter locations;
27
1168421
TRIGGER VALVE LEVER
1
28
1168418
FILTER LP-3
1
29
942920
STRAINER (PJ)
1
• This sprayer is an electronic tool and must be protected from
severe environmental conditions. When not using, do not
leave the sprayer in sun, rain or frost;
• Do not submerge the sprayer completely or partially;
• After finishing the application, clean and wash all equipment
in an approved decontamination area;
• Clean the sprayer before storage. Circulate fresh water
through the tank, pump and hoses after each use. This will
help remove chemical residues and extend life of sprayer
parts;
• Nozzles and filters must be periodically cleaned or replaced.
Do not clean nozzles or filters with sharp hard objects, nor
blow through them using the mouth.
30
1224068
TANK PJB-20c WITHOUT LOGO
1
30a
1224070
TANK PJB-16c WITHOUT LOGO
1
31
560573
LID DIAPHRAGM (NITRILE)
1
32
4739
LID WITH DIAPHRAGM (ORANGE)
1
33
1220618
COMPLETE BELT WITH TRANSPORT HANDLE
1
2
34
635672
BUCKLE HD
35
1168419
TRIGGER VALVE ASSEMBLY LP-3
1
36
1188330
LANCE LP600 WITH TRIGGER LP3
1
11/16
WARNING!
•
Do not spray near people who are not using
PPE, springs, lakes and rivers.
head protector
•
eyes protector
dust mask
•
WARNING!
In case of an accident remove the sprayer immediately as shown in the illustration below.
long-sleeved shirt
•
•
smock
•
gloves
•
•
long pants
•
boot
•
•
WARNING!
•
•
Use of individual protective clothing and
safety equipment is required.
9. Maintenance
For extended product life, follow these important care instructions:
WARNING!
Use the correct dose and volume of chemical
according to the product label.
• When filling up the tank, always use the strainer provided.
This will reduce the chance of undesirable debris that could
damage the pump.
• Do not operate the sprayer without the pump suction filter.
This can severely damage the pump. Periodically clean or replace this filter as follows:
1.
Empty the tank, make sure the sprayer is turned off and
put it upside down;
2.
Remove screw A;
3.
Remove base cover B;
4.
Unscrew filter cover C;
5.
Clean or replace filtering element D.
7.1. Triple rinse of empty agrochemicals
containers
NOTE: Even the containers considered empty contain chemical
residues. Therefore, discarding the containers without washing
out the residues is extremely dangerous to man, animals and environment. In the case of metal, plastic and glass chemical containers, each container must be rinsed three times to ensure the
residues are completely removed. This manual describes how to
make the triple rinse in a correct, safe and effective way.
1.
Spray downwind and avoid
drift
10/16
Keep constant height
Serious risk of poisoning.
Do not mix chemical products, unless
recommended by manufacturer. Intense
chemical reactions can occur.
Read the label of chemical products
carefully. Always follow manufacturer’s
recommendations.
High pressure present at end of nozzle
and inside sprayer base. Turn-off the
sprayer completely and release pressure
before attempting to repair or replace parts
of the sprayer.
Do not direct spray towards bystanders.
Spray may be toxic.
After the use of herbicides always clean
the equipment before using other formulations.
Wear individual protection equipment.
Wear gloves, safety glasses, safety mask and
protective clothing.
Clean yourself after spraying. Take a
shower with plenty of soap and water. Put
on clean clothes.
The clothing used during spray application must be washed separate from other
clothes of ordinary use.
Keep chemical products out of reach of
children and animals. Lock up the chemical
products to prevent untrained persons from
handling them.
In case of intoxication, see a doctor
immediately. Show him/her the chemicals
manufacturer’s label.
Dispose of chemical containers properly.
Observe your local regulatory agency recommendations and follow manufacturer’s
disposal instructions.
Do not pollute the environment.
During the transport in vehicles, the
sprayer must be turned off and secured.
Always keep the trigger valve shut during
transport and when not using the sprayer.
2.
Hold the container in the upright position and fill it with
water up to 1/4. For example: in a 1000 ml container, put
250 ml of water.
3.
Install the container cap and tighten enough to avoid
leakage during the agitation.
4.
Agitate the container strongly in all ways (horizontal and
vertical), for approximately 30 seconds to remove the residues that are on the container internal walls.
5.
Take the container cap off and carefully pour the rinse water into the spray tank.
6.
Keep holding the container over the spray tank opening
for approximately 30 seconds to the last drop.
7.
Repeat this operation twice more. This way, you complete
the triple rinse.
8.
Make the plastic and metallic containers useless by piercing the container bottom with a pointed instrument. This
way, their labels are not damaged for identification purposes.
Immediately after emptying the container, you must keep
it with the opening upside down over the sprayer tank
opening or over the bucket that you are using to prepare
the chemical mixture for at least 30 seconds, until no residue is left in the container, when the drops are falling in
long intervals.
7/16
8. Operating Instructions
Band width
ft (m)
1.6
(0.5)
2.2
(0.7)
3.2
(1.0)
3.9
(1.2)
4.9
(1.5)
Distance to
walk ft (m)
164
(50.5)
117.1
(35.7)
82.0
(25.0)
68.2
(20.8)
54.7
(16.7)
The following steps describe how to safely use the sprayer.
8.1. Select the correct nozzle
NOZZLE
FILTER (Mesh)
TYPE
IDENTIFICATION
(Part no. - Description)
80 (Zinc yellow)
(1197535) JEF 110015
GREEN
50(Gentian blue)
(1197536) JEF 11002
YELLOW
50(Gentian blue)
(1197537) JEF11003
BLUE
APPLICATION
Herbicides
80 (Zinc yellow) (1197475) JSF 110015
GREEN
50(Gentian blue)
(1197476) JSF 11002
YELLOW
50(Gentian blue)
(1197477) JSF11003
BLUE
50(Gentian blue)
(1197565) JHC 8002
YELLOW
50(Gentian blue)
(1198892) JHC 8004
RED
50(Gentian blue)
(1198893) JHC 8005
BROWN
50(Gentian blue)
(1197486) JDF 04
RED
50(Gentian blue)
(1197487) JDF 05
BROWN
50(Gentian blue)
(1197488) JDF 06
GREY
80 (Zinc yellow)
(1197497) JAI 120015
GREEN
80 (Zinc yellow)
(1197499) JAI 12002
YELLOW
50(Gentian blue)
(1197501) JAI 12003
BLUE
PRESSURE FLOW RATE
gpm (L/min)
(psi)
30
0.13 GPM
(0.49 L/min)
30
0.17 GPM
(0.65 L/min)
30
0.26 GPM
(0.98 L/min)
30
0.13 GPM
(0.49 L/min)
30
0.17 GPM
(0.65 L/min)
30
0.26 GPM
(0.98 L/min)
45
0.21 GPM
(0.80 L/min)
45
0.42 GPM
(1.60 L/min)
45
0.53 GPM
(2.00 L/min)
15
0.24 GPM
(0.92 L/min)
15
0.30 GPM
(1.15 L/min)
15
0.37 GPM
(1.39 L/min)
20
0.11 GPM
(0.42 L/min)
20
0.15 GPM
(0.57 L/min)
20
0.22 GPM
(0.85 L/min)
• Attach the calibrator bottle to the lance as shown:
4.
8.4. Shoulder strap adjust (16c and 20c)
The tank is contoured for the operator comfort. The shoulder
straps can be quickly adjusted to properly position the sprayer
on the operator’s back.
1.
Mount the strap belt onto the tank as shown in position A.
2.
Hook the buckle of the strap to the plastic couplers located at the side of the sprayer’s base, as shown in position B.
3.
To tighten the strap belt, hold the strap buckle firmly with
one hand and pull the handle downward with the other
hand. To loosen the strap belt, hold the buckle firmly with
one hand and pull the strap upward with the other hand.
Fungicide,
insecticide
and
foliar
fertilizers
Herbicides
and
foliar
fertilizers
Herbicides
Cover
Nozzle
Nozzle cap
Calibrator
bottle
A
• Mount the calibrator cover to the lance.
• Screw the calibrator onto the cover.
2.
Hold the lance at the working height and spray to measure the application band width.
3.
Based on the band width, calculate the total walking distance required to spray the desired area. Use the chart as
shown next.
1.
Turn on the sprayer using the ON/OFF switch in the electric panel.
2.
Place the lance with the trigger valve pressed above the
base of the sprayer until the spray jet begins to spray continuously.
3.
Direct the spray lance to a safe position and open the trigger valve to begin spraying.
To turn off the sprayer:
1.
Shut off the trigger valve. The internal pump pressure
switch will automatically turn off the pump (the sprayer is
said to be in idle state).
2.
Turn off the sprayer using the ON/OFF switch in the electric panel.
3.
Direct the spray lance to a safe position and open the trigger valve to release pressure before storing the sprayer.
B
8.5. Shoulder strap adjust (8c)
Record the time it takes to walk
340 sq/ft (1/128th acre)
Simulate the spraying of 340
sq/ft (1/128th acre)
1.
Hold the lance at the normal working height and spray
into the bottle while walking the distance required to
spray an area corresponding to 340 sq/ft (1/128th acre).
2.
Place the bottle on a level surface and observe the liquid
level visible through the side of the bottle. The ounces
collected corresponds to gallons per acre. For example if
you collected 10 ounce while spraying 340 sq/ft this equal
10 GPA.
3.
Empty the bottle and repeat this operation to determine
the average of two or more readings.
PROCEDURE
USING CALIBRATOR BOTTLE (OPTIONAL)
To turn on the sprayer:
• Reinstall the filter, nozzle and cap.
NOTE: This sprayer is packaged with the Blue Adjustable Cone
nozzle fitted in the lance. Other nozzles mentioned in this manual are optional, so they do not accompany this sprayer.
1.
NOTE: Before starting to spray, retighten the hose clamps to
avoid contamination of the operator and of the environment.
• Remove the cap, nozzle and filter.
*Approximate data based on a spray swath for unique nozzles at
20 inch height of the target.
8.2. Calibration of battery powered knapsack sprayer
8.6. Turn On/Off the sprayer
Lance
Filter
Herbicides
Pour the solution into the tank while filling with water.
1.
Mount the strap belt onto the tank as shown in position A.
2.
Finally, adjust the strap length as desired, as shown in B.
To tighten the strap belt, hold the strap buckle firmly with
one hand and pull the handle.
8.7. Application
B
A
Wear appropriate protective clothing
NOTE: To convert GPA to L/ha multiply by 9.353.
8.5. Filling the spray tank with pesticides.
Band
width
8/16
1.
Read carefully the chemicals manufacturer’s labels;
2.
Put 1.3 gallon (5 Liters) of water in a bucket and add the
chemical product;
3.
Stir until it becomes an homogeneous mixture;
Handle
Buckle
Buckle
Do not contaminate water
9/16
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement