advertisement
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • snowdoggplows.com
SnowDogg
®
Snowplow Headlight Adapter
INSTALLATION INSTRUCTIONS
16071130
HB1
HB1/9004 DODGE 1994-1998
1994-1998
Ram 1500
RAM 2500/3500
HB1/9004
SWITCHED GROUND
DODGE 1999-2001
1999-2002
RAM 1500 - NON SPORT - 2 LAMPS
RAM 2500/3500 - NON SPORT - 2 LAMPS
If your application is not shown here, contact your dealer for further assistance
NOTE: The 16071130 Headlight Adapter is only for use with HB1 headlights. HB5 headlights use the same connector, but require a 16071120 adapter. Always check the application guide and your bulb marking before installation.
INSTRUCTIONS
Always verify that all truck lights are functioning correctly before beginning any installation.
1. Disconnect both PS and DS side truck headlights from the truck headlight harnesses.
2. Connect the 16071130 adapters to the truck headlights and truck headlight harnesses.
3. Connect the 16071130 adapters to the 8-pin RELAY HARNESS connectors.
4. Use an included Tap connector to tap the PURPLE wire into the TURN light circuits on the passenger and driver sides of the truck.
If the truck is a SWITCHED GROUND INSTALL – skip step 5 and go to the special instructions.
5. Use an included Tap connector to tap the BROWN wire into the PARK light circuits on passenger and driver sides of the truck.
6. Check all light functionality before operating the plow.
—continued on back
9049 Tyler Blvd. • Mentor, Ohio 44060
Phone (440) 974-8888 • Fax (440) 974-0165
Toll-Free Fax 800-841-8003 • snowdoggplows.com
SPECIAL INSTRUCTIONS FOR:
DODGE 1500 1999-2001 2 LAMP (NON-SPORT) –
SWITCHED GROUND INSTALL
DODGE 2500/3500 1999-2002 2 LAMP (NON-
SPORT) – SWITCHED GROUND INSTALL
NOTE: Auxiliary relay kit 16071210 is required on most switched ground Dodge’s to ensure proper operation when the vehicle is turned off. Without this kit, with ignition in the off position, the relay module may buzz, the parking lights on the will remain on, and the high beam indicator will be lit.
The 16160100 RELAY HARNESS must be installed for SWITCHED GROUND configuration per the diagram shown on back .
1. Locate the gray wire with pre-connected male/ female quick connects. Disconnect the two halves.
The male quick connect will not be used and should be taped off.
2. The female end should be connected to the
RED/WHITE wire from the 16160300 CONTROL
HARNESS
3. CONNECT THE BROWN WIRES ON THE
HEADLIGHT ADAPTERS TO GROUND - THEY DO
NOT CONNECT TO THE PARKING CIRCUIT.
4. Connect the WHT/BLK, ORANGE, and BLACK wires as shown. Do not heat-shrink or seal – these will be disconnected when the 16071210 is installed.
5. Verify function of headlights, parking lights, and turn signals on plow and truck.
6. Follow 16071210 installation instructions.
SWITCHED GROUND HEADLIGHTS
(SEE APP GUIDE FOR ASSISTANCE)
RELAY HARNESS
WHITE/BLK
CONTROL HARNESS
BLACK
ORANGE
GRAY
NOT USED - COVER END
WITH TAPE OR HEAT SHRINK
RED/WHITE
GRAY
HARNESS REFERENCE
Make sure to apply dielectric grease to each connection
16071130INST Rev D
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project